INSTRUCTION MANUAL - CIRCUTORdocs.circutor.com/docs/M064B01-03.pdf · Instruction Manual 7 Wibeee 1...

INSTRUCTION MANUAL

Consumption analysers

(M064B01-03-20A)

SMART PLUGGING

2

Wibeee

Instruction Manual

3Instruction Manual

Wibeee

SAFETY PRECAUTIONS

DANGERWarns of a risk, which could result in personal injury or material damage.

ATTENTIONIndicatesthatspecialattentionshouldbepaidtoaspecificpoint.

Follow the warnings described in this manual with the symbols shown below.

If you must handle the unit for its installation, start-up or maintenance, the following should be taken into consideration:

Incorrect handling or installation of the unit may result in injury to personnel as well as damage to the unit. In particular, handling with voltages applied may result in electric shock, which may cause death or serious injury to personnel. Defective installation or maintenance may also leadtotheriskoffire.Read the manual carefully prior to connecting the unit. Follow all installation and maintenance instructions throughout the unit’s working life. Pay special attention to the installation stan-dards of the National Electrical Code.

Refer to the instruction manual before using the unit

In this manual, if the instructions marked with this symbol are not respected or carried out correctly, it can result in injury or damage to the unit and /or installations.

CIRCUTOR,SAreservestherighttomodifyfeaturesortheproductmanualwithoutpriornotification.

DISCLAIMER

CIRCUTOR, SAreservestherighttomakemodificationstothedeviceortheunitspecifica-tions set out in this instruction manual without prior notice.

CIRCUTOR, SA on its web site, supplies its customers with the latest versions of the device specificationsandthemostupdatedmanuals.

www.circutor.com

CIRCUTOR, recommends using the original cables and accessories that are supplied with the device.

4

Wibeee

Instruction Manual

CONTENTSSAFETY PRECAUTIONS ��3DISCLAIMER ��3CONTENTS ��4REVISION LOG ��6SYMBOLS ��61�- VERIFICATIONS UPON RECEPTION ��72�- DESCRIPTION OF THE PRODUCT ��73�- INSTALLING THE DEVICE ��8

3�1�- PRELIMINARY RECOMMENDATIONS ��8 3�2�- INSTALLATION ��9 3�3�- DEVICE TERMINALS ��10

3�3�1�- Wibeee-M-L ��103�3�2�- Wibeee-M-R ��103�3�3�- Wibeee-T-L �� 113�3�4�- Wibeee-T-R �� 11

3�3�5�- Wibeee-3P ��123�4�- CONNECTION DIAGRAMS ��12

3�4�1�- Wibeee-M-L ��123�4�2�- Wibeee-M-R ��133�4�3�- Wibeee-T-L ��133�4�4�- Wibeee-T-R ��143�4�5�- Wibeee-3P ��14

3�5�- STARTING UP THE DEVICE ��153�5�1�- APPLICATION MODE ��153�5�2�- DIRECT SHARE MODE ��16

3�6�- CALIBRATION ��174�- OPERATION ��18

4�1�- OPERATING PRINCIPLE ��18 4�2�- MEASUREMENT PARAMETERS ��18

4�2�1�- Wibeee-M-L and Wibeee-M-R ��184�2�2�- Wibeee-T-L, Wibeee-T-R and Wibeee-3P ��19

4�3�- LED INDICATORS ��19 4�4�- BUTTON ��20 4�5�-START-UP ��20

5�- DISPLAY AND CONFIGURATION ��22 5�1�-MOBILE APPLICATION ��22 5�2�- WEB PLATFORM ��23

5�2�1�- HOME ��245�2�2�- DASHBOARD ��285�2�3�- DEVICES ��295�2�4�- NOTIFICATIONS ��295�2�5�- REPORTS ��30

5�2�6�- HELP ��325�3�- INTERNAL WEB SERVER ��32

5�3�1�- INSTANT DATA��335�3�2�- NETWORK ��345�3�3�- ADVANCED OPTIONS ��345�3�4�- GENERAL OPTIONS ��35

5�4�- CONFIGURATION THROUGH HTTP GET REQUESTS ��355�4�1�- PARAMETER QUERY ��355�4�2�- CONFIGURATION ��38

6�- WIRELESS COMMUNICATIONS ��40 6�1�- USAGE ENVIRONMENT AND HEALTH ��40 6�2�- Wi-Fi COMMUNICATIONS ��40 6�3�- MODBUS TCP PROTOCOL ��40 6�4�- MODBUS MEMORY MAP ��41

7�- TECHNICAL FEATURES ��438�- MAINTENANCE AND TECHNICAL SERVICE ��46

5Instruction Manual

Wibeee

9�- WARRANTY ��4610�- CE CERTIFICATE ��47

6

Wibeee

Instruction Manual

REVISION LOGTable 1: Revision log�

Date Revision Description01/18 M064B01-03-18A Initial Version

08/18 M064B01-03-18B Changes in the following sections:7

02/20 M064B01-03-20A Changes in the following sections:2.- 3.5. - 5.2.1.1.

Note: The images of the devices are for illustration purposes only and may differ from the orig-inal device.

SYMBOLS

Table 2: Symbols�Symbol Description

Compliant with the relevant European standards.

Do not remove from hazardous live conductors or place it around them.

Double insulation.

~ AC current.

Device covered by European directive 2002/96/EC. At the end of its usefullife, do not leave the device in a household waste container. Follow local regulations on electronic equipment recycling.

7Instruction Manual

Wibeee

1�- VERIFICATIONS UPON RECEPTION

The following must be checked upon reception of the device:

a)Thedevicehasbeensuppliedaccordingtothespecificationsinyourorder. b) The device has not been damaged during transport. c) Perform an external visual inspection of the device before connecting it. d) Check that it has been supplied with the following:

- An installation guide, - A set of magnets,

2�- DESCRIPTION OF THE PRODUCT

Wibeee is a new method for electrical data acquisition, to facilitate decision making when it comes to understanding the use of electrical energy. The technology used, which is attached via a clip, is based on the patented DINZERO system and consists of simply attaching the de-vice to the cable or to the upper part of an MCB (miniature circuit breaker). Once switched on, the device will begin to convert the measured parameters into information that is sent via a wireless connection.

There are 5 models available:

Wibeee-M-L single-phase model with a neutral connection on the left. Wibeee-M-R single-phase model with a neutral connection on the right. Wibeee-T-L three-phase model with a neutral connection on the left. Wibeee-T-R three-phase model with a neutral connection on the right. Wibeee-3P three-phase model with no neutral connection.

The models have:

- 2 indicator LEDs- 1 Reset button

- Wi-Fi communications You can access the data measured by the device via the Wibeee Circutor mobile application, the website http://wibeee�circutor�com, or the device's internal web server.

8

Wibeee

Instruction Manual

3�- INSTALLING THE DEVICE

3.1.- PRELIMINARY RECOMMENDATIONS

In order to use the device safely, it is critical that individuals who handle it follow the safety measures set out in the standards of the country where it is being used, use the personal protective equipment necessary (rubber gloves, face protection andapprovedflame-resistantclothing)topreventinjuriesduetoelectricshockorelectric arc due to exposure to current-carrying conductors and pay attention to the various warnings indicated in this instruction manual.

The Wibeeedevicemustbeinstalledbyauthorisedandqualifiedstaff.

Disconnect the device from the power supply and disconnect the measuring devices before handling, changing the connections or replacing the device. Handling the device while it is con-nected is hazardous to people nearby.

It is essential to keep the cables in a perfect condition to avoid accidents, personal injury and damage to installations.

Limittheoperationofthedevicetomeasuringthespecifiedcurrentorvoltagevalues.

The manufacturer of the device shall not be held responsible for any damage resulting from the user or installation company failing to observe the warnings and/or recommendations indicated in this manual nor for any damage resulting from the use of non-original products or accesso-ries or those from other brands.

Do not use the device to take measurements if you detect an anomaly or malfunction.

Check the environment in which the device is installed before taking a measurement. Do not use the device to take measurements in dangerous, explosive, wet or damp environments.

Disconnect the device from the mains and from the power supply (both the device and its measuring system) before performing any maintenance work, repairs or handling any of the connections of the device. Contact the after-sales service if you detect that the device is not working prop-erly.

9Instruction Manual

Wibeee

3.2.- INSTALLATION

Before using the Wibeee ensure that the conditions are appropriate for working, and that the protective equipment is adequate�

Use of the Wibeee on uninsulated conductors is limited to 265 V~ to the power frequency.

For measuring of uninsulated conductors, use the appropriate and necessary personal protective equipment.

The device should be installed after the circuit breaker. (Imax: 63 A)

To install the device, carry out the following steps:

1� Remove the protective panel from the electric panel.

Figure 1: Remove the connection panel�

2� When installing the device, make sure that the neutral terminal (N) corresponds with the neu-tral cable of the installation (your device could be damaged if incorrectly installed).Place the magnetic connectors in the direction of the circuit breaker and near to the casing of the Wibeee.

Figure 2: Install the device�

10

Wibeee

Instruction Manual

3� Check that it is secured.

4� Check that the red LED is on and blinking.

5� After a few seconds, the blue LED will start blinking.

3.3.- DEVICE TERMINALS

3�3�1�- Wibeee-M-LTable 3:List of terminals of the Wibeee-M-L�

Terminals of the Wibeee-M-L device1: N, Neutral2: L1, Voltage input

1 2

Figure 3:Wibeee-M-L Terminals�

3�3�2�- Wibeee-M-RTable 4:List of terminals of the Wibeee-M-R�

Terminals of the Wibeee-M-R device1: L1, Voltage input2: N, Neutral

1 2

Figure 4:Wibeee-M-R Terminals�

11Instruction Manual

Wibeee

3�3�3�- Wibeee-T-LTable 5:List of terminals of the Wibeee-T-L�

Terminals of the Wibeee-T-L device1: N, Neutral 3: L2, Voltage input L22: L1, Voltage input L1 4: L3, Voltage input L3

1 2 3 4

Figure 5:Wibeee-T-L Terminals�

3�3�4�- Wibeee-T-RTable 6:List of terminals of the Wibeee-T-R�

Terminals of the Wibeee-T-R device1: L1, Voltage input L1 3: L3, Voltage input L32: L2, Voltage input L2 4: N, Neutral

1 2 3 4

Figure 6:Wibeee-T-R Terminals�

12

Wibeee

Instruction Manual

3�3�5�- Wibeee-3PTable 7:List of terminals of the Wibeee-3P�

Terminals of the Wibeee-3P device1: L1, Voltage input L1 3: L3, Voltage input L32: L2, Voltage input L2

1 2 3

L2 L3

Figure 7:Wibeee-3P Terminals�

3.4.- CONNECTION DIAGRAMS

3�4�1�- Wibeee-M-L

N L

Figure 8: Wibeee-M-L connection diagram�


Wibeee

3�4�2�- Wibeee-M-R

NL

Figure 9: Wibeee-M-R connection diagram�

3�4�3�- Wibeee-T-L

N L1 L2 L3

Figure 10: Wibeee-T-L connection diagram�

14

Wibeee

Instruction Manual

3�4�4�- Wibeee-T-R

NL1 L2 L3

Figure 11: Wibeee-T-R connection diagram�

3�4�5�- Wibeee-3P

L1 L2 L3

Figure 12: Wibeee-3P connection diagram�


Wibeee

3.5.- STARTING UP THE DEVICE

To start communication with the device it is necessary:

1�- To have access to the Internet through a wireless network.

2�- To check that the following ports are open:

- Port 8080 for Http Get / Post. - Port 53 for DNS - Port 80 for Internet

Note: The Orange Livebox Next router is incompatible with Wibeee devices when in “WPA/WPA2” security mode and they do not connect. When in “only WPA2” mode they connect cor-rectly.

Note: For the correct functioning of the Wibeee, it is necessary to connect it to one of the first 11 Wi-Fi channels.

The Wibeee's data can be accessed in two ways:

Application mode. Direct share mode.

3�5�1�- APPLICATION MODE

In application mode, the data measured by the Wibeee is uploaded to the cloud and accessed using the Wibeee CIRCUTOR application. When using this mode, the Wibeee and the user whohasconfigureditarelinked,sotheusercancontrolthedevice,viewthedatathathasbeensent and the charts and manage groups of devices.

To start the device in application mode, follow these steps:

1�- Scan the QR code to download the application or download it from:http://wibeee�circutor�com

2�- Open the Wibeee CIRCUTOR application. And follow the steps that it indicates.

16

Wibeee

Instruction Manual

3�5�2�- DIRECT SHARE MODE

In direct share mode the Wibeee's data is directly accessed from the device's integrated web server, so you can view the measurements being captured at that moment in real time and manuallyconfigurethedevice.Thisallowsyoutochangeparameters,suchastheserverandport to which the Wibeee willsendthedata.IfyouconfigureaWibeee while using this mode, there is no link between the user and the device, so the only way to access the device when it is connected to the network is by knowing its IP address and accessing it using a search tool.

To start the device in direct share mode, follow these steps:

1�- On a smartphone/tablet, use the Wi-Fi connection's settings to connect to the Wibeee�

2�-Youcangetaccesstothenetconfigurationandinstantmeasurementsthroughyourbrows-er, at the address: http://192�168�1�150

User: user Password: user


Wibeee

3.6.- CALIBRATION

When the device has been installed and started, it needs to be calibrated.

The calibration process appears automatically in the Wibeee Circutor mobile application dur-ing installation.

Follow these steps:

1�- When the device has been successfully installed, measure the current of the L1 with a cur-rent clamp, and enter the value on the calibration screen, Figure 13.

Note: calibration should be performed when the device has a current flow of 5 ... 10 A.

Figure 13: Calibration screen�

2�- Repeat the calibration process for each of the device's measurement cables.

If you skip the calibration process while installing the device, the accuracy of the measurements is not guaranteed.

If the measurement cables are replaced or moved after calibration has been performed, it must be repeated. You can calibrate the device again via the Edit menu.

18

Wibeee

Instruction Manual

4�- OPERATION

4.1.- OPERATING PRINCIPLE

The Wibeee is a power consumption measurement device with a Wi-Fi wireless connection to display or download the data that is measured, using any smartphone, tablet or PC.

Electrical Panel Wibeee Laptop PC Smartphone Tablet

Figure 14: Overview

The device can work in two operating modes:

Application mode In application mode, the data measured by the Wibeee is uploaded to the cloud and ac-cessed via the Wibeee CIRCUTOR application or the http://wibeee�circutor�com web platform.

Direct share modeIn direct share mode the Wibeee's data is directly accessed from the device's integrated web server.

Note: The device's integrated web server can also be accessed in the application's operating mode.

4.2.- MEASUREMENT PARAMETERS

The device measures and logs the following parameters:

4�2�1�- Wibeee-M-L and Wibeee-M-RTable 8: Measurement parameters of the Wibeee-M-L and Wibeee-M-R�

Parameter UnitsVoltage VCurrent AFrequency HzActive Power kWApparent Power kVAInductive Reactive Power kvarLCapacitive Reactive Power kvarCPower Factor PFActive Energy kWhReactive Energy kvarh


Wibeee

Table 8 (Cont�): Measurement parameters of the Wibeee-M-L and Wibeee-M-R�

Parameter UnitsInductive Reactive Energy kvarLhCapacitive Reactive Energy kvarChCost -CO2 Emissions KgCO2

4�2�2�- Wibeee-T-L, Wibeee-T-R and Wibeee-3P

Table 9: Measurement parameters of the Wibeee-T-L, Wibeee-T-R and Wibeee-3P�

Parameter Units Phases L1-L2-L3 Total

Voltage V

Current A

Frequency Hz

Active Power kW

Apparent Power kVA

Inductive Reactive Power kvarL

Capacitive Reactive Power kvarC

Power Factor PF

Active Energy kWh

Reactive Energy kvarh

Inductive Reactive Energy kvarLh

Capacitive Reactive Energy kvarCh

Cost -

CO2 Emissions KgCO2

4.3.- LED INDICATORS

The device has 2 status LEDs, Figure 15 and Table 10.

L2 L3

Blue Red Blue Red Blue Red

Figure 15:LED indicators�

20

Wibeee

Instruction Manual

Table 10: Description of the LEDs�

LED Description Red Blinking light: Powered device.

Blue

Indicates the connection status:Slow blinking light (1s): Generating a Wi-Fi network.Fast blinking light (<1s) : Connected to a Wi-Fi network.Steady light: Data being sent over the network.

4.4.- BUTTON

The device has a Reset button, Figure 16, to restore the device's factory settings (hold it down for more than 6 seconds).

Reset Reset

L2 L3

Reset

Figure 16:Reset Button�

4.5.-START-UP

During the start-up of the device, the Wibeee goes through different states:

1�- Configuration state

Blue LED→Slowblinkinglight(1s)Red LED→Slowblinkinglight(1s)

In this state, the Wibeee generates its own Wi-Fi network called WIBEEE_xx:xx:xx� Itisonlyusedtoconfigurethedeviceandconnectittotheuser'snetwork.

If you want to return to this state to obtain the initial conditions, you should hold down the Re-set button for more than 6 seconds. The device deletes any previous settings and restores the default values.

2�- Connecting�� state

Blue LED→OffRed LED→Slowblinkinglight(1s)

In this state, the Wibeee is managing the connection with the router/access point.This state should last for 40 seconds, when there is good Wi-Fi coverage. In places where there is weak Wi-Fi coverage, it may take longer.


Wibeee

If it takes longer than 2 minutes, it is recommended to return to the initial state, check the Wi-Fi coverage and re-start the process.

If it is unable to connect to the Wi-Fi, the device retries 5 times. If the lack of connection per-sists, it goes into Configurationmode(sothattheconfigurationcanbechangedwithoutopen-ing the panel) for 5 minutes; it then tries to reconnect again and, until it manages to reconnect, it remains in this alternating mode. (5 minutes in the Configuration state and 1 attempt to connect).

3�- Connecting state

Blue LED→Fastblinkinglight(<1s)Red LED→Slowblinkinglight(1s)

Inthisstate,thedevicehasconnectedtotheWi-Finetworkandiswaitingtocompletethefirstsuccessful transfer of data.Whenitfirstmanagestosuccessfullysenddata,itwillenterthe“Connected and sending OK” state.

Ifthedeviceisnotabletosuccessfullysendthefirstsetofdata,itwillretry3times.Ifitdoesnotmanage to send it, the Wi-Fi connection is restarted and it retries sending the package 3 times. Itremainsinthisstateuntilthefirstdataissuccessfullysent.

4�- Connected and sending OK state

Blue LED→Steadylight.Red LED→Slowblinkinglight(1s)

When thedevice is configuredand connected to thenetwork in theuser's infrastructure, itautomatically starts sending data on the installation's power consumption to the server (every minute).It also allows you to access instant measurements by making requests to its internal XML and Modbus servers.

22

Wibeee

Instruction Manual

5�- DISPLAY AND CONFIGURATION

When the device has been installed and started up, it is possible to access all of its data by using different methods, depending on the device's operating mode, Figure 17.

Application mode Direct share mode

Internal Webserver

Web platformhttp://wibeee.circutor.com

Mobile applicationWibeee Circutor

Internal Webserver

Data display

Figure 17: Data display based on the operating mode�

5.1.-MOBILE APPLICATION

The Wibeee Circutor mobile application is compatible with iOS and Android, and has a version for smartphones and tablets.

Inityoucanviewandconfigurealloftheparametersmeasuredbythedevice.

Figure 18: Wibeee Circutor mobile application�


Wibeee

5.2.- WEB PLATFORM

Figure 19 shows the main screen of the http://wibeee�circutor�com web platform.

Figure 19:Main screen of the web platform�

From this screen you can access the different sections of the platform:

: Home, summary of consumption, displays charts and gives access to the dashboardconfigurationoptions(graphicalinterface).

: Dashboard, displays all of the dashboards of every active device.

: Devices, access to all of the connected devices.

: Notifications,displaysthenotificationslog.

: Reports, access to regular report generation.

: Help, help screen.

24

Wibeee

Instruction Manual

5�2�1�- HOME

The Home screen is divided into different areas:

The area in Figure 20 displays a summary of consumption and CO2 emissions from the previous month, the current month and the forecast for the end of the month. It also displays the set target value.

Figure 20: Summary area�

The area in Figure 21 shows 2 of the possible charts that can be viewed. Table 8 and Table 9 show all of the parameters that can be graphically displayed. Use the < > arrows to toggle between charts.


Wibeee

Figure 21: Charts area�

The area in Figure 22 shows the latest measurements sent by the device.

Figure 22: Measurements area�

In the area in Figure 23 you can access the configuration options for the devices and dashboard, see “5.2.1.1.- Configuration screen for the devices/dashboard”.

Figure 23: Access to the device/dashboard configuration area.

26

Wibeee

Instruction Manual

5.2.1.1.- Configuration screen for the devices/dashboard.

Onthedevice/dashboardconfigurationscreenyoucanconfigurethefollowingdata:

DEVICE

Figure 24: Configuration screen: Device.

The device's basic data is entered in this section: Name: The name of the device.Select Dashboard: Dashboard selection.Mac: MAC address of the device.2-4 Quadrants: Measurement selection for 2 quadrants (consumption) or 4 quadrants (consumption and generation).

LOCATION

Figure 25: Configuration screen: Location.


Wibeee

The device's location data is entered in this section: Name: Name of the device's location.Time zone: Time zone.Longitude, Latitude: Location of the device.

COST

Figure 26: Configuration screen: Cost

The costs are entered in this section: Price kWh : Price of kWh.Tax (%), Other Tax (%) : Fees and taxes.Other Costs (Cost/day): Other costs.Cost kW Day (Cost/kW Day): Cost in kW per day.Billing date: Billing date.Contracted power (kW): Contracted power.

TARGET AND NOTIFICATIONS

Figure 27: Configuration screen: Target and Notifications.

28

Wibeee

Instruction Manual

In this section you enter the following: Target Limit (kWh) : The maximum consumption value that you want to reach, in kWh.

Andthefollowingnotificationsareactivatedordeactivated:

• Wibeee has been inactive for 1 day, Wibeee has been without sending data to the Web platform for more than a day.

• Wibeee has been inactive for 3 days, Wibeee has been without sending data to the Web platform for more than three days.

• Overvoltage, Wibeee has detected a overvoltage (> 253 V ) for more than one minute in the last hours (> 253V, t > 1 min.)

• Undervoltage,Wibeeehasdetectedaundervoltage(<207V)formorethanoneminuteinthelasthours(<207V,t>1min.)

• High consumption, alarm for high consumption in the installation, with the current consumption the limit established in the Wibeee will be exceeded at the end of the month.

5�2�2�- DASHBOARD The Dashboard screen, Figure 28, shows all of the active dashboards.

Figure 28: Dashboard Screen�

It is also possible to create a chart comparing different dashboards. To do this, simply select the dashboards that you want to compare by ticking the box, as shown in Figure 29.

Figure 29: Selecting the Factory dashboard�


Wibeee

5�2�3�- DEVICES

The Devices screen, Figure 30, displays a list of all of the connected devices.

Figure 30: Devices screen�

5�2�4�- NOTIFICATIONS

The Notifications screen, Figure 31,showsa logofallof thenotificationsthathavebeengenerated.

Figure 31: Notifications screen.

30

Wibeee

Instruction Manual

5�2�5�- REPORTS

The Reports screen, Figure 32, is divided into two areas:

Figure 32: Reports Screen�

REPORTSThis section shows the scheduled reports to be regularly generated.

To create a new regular report, press the icon. The dialogue box in Figure 33 opens.

Figure 33: New Report�


Wibeee

In this dialogue box, you should enter:

Report name: Name with which the report is going to be saved.Select Dashboard: Select the Dashboard on which you are going to prepare the report.Frequency: Select the frequency of the report: Weekly, Monthly, Billing period.Recipients: Enter the email addresses of the recipients of the report.

You can prepare a simple version of a report by selecting Normal Section (Figure 33), where everythingispre-configuredandyouonlyhavetoselectthequantity.Or an advanced version, by selecting Advanced Section (Figure 34),whereyoucanconfigurea lot more options.

Figure 34: New Report: Advanced Section�

REPORT LOG

In this section you can download all of the reports that have already been created.

32

Wibeee

Instruction Manual

5�2�6�- HELP

The Help screen, Figure 35, tries to answer any questions about the installation, operation, web platform and application of the two Wibeee systems.

Figure 35: Help Screen�

5.3.- INTERNAL WEB SERVER

Figure 36 shows the screen where you access the device's internal web server. The device's default address is: http://192�168�1�150

User: user Password: user

Figure 36:Internal web server access screen�

The main screen is shown in Figure 37�


Wibeee

Figure 37:Main screen of the internal web server�

5�3�1�- INSTANT DATA

In this section you can access instant data from each of the measurement phases, Figure 38.

Figure 38:Internal web server: Instant Data�

34

Wibeee

Instruction Manual

5�3�2�- NETWORK

YoucanconfigurethenetworkparametersintheNetwork section, Figure 39.

Figure 39:Internal web server: Network�

5�3�3�- ADVANCED OPTIONS

YoucanconfiguretheIPparametersintheAdvanced Options section, Figure 40.

Figure 40:Internal web server: Advanced Options�

wibeee.circutor.com


Wibeee

5�3�4�- GENERAL OPTIONS

Figure 41 shows the General Options section.

Figure 41:Internal web server: General Options�

Youcanconfigurethefollowingparametersinthissection:

Measures Refresh Time (s): The measurement refresh time.Data Refresh Time (min): The data refresh time. If the value is set to -1, the sending of data is deactivated.It is also possible to reset the energy meter, by pressing the button.

5.4.- CONFIGURATION THROUGH HTTP GET REQUESTS

Wibeee accepts HTTP GET requests for parameter and settings queries for the device. Requests must be made directly to the IP address: 192.168.1.150 after connecting to the Wi-Fi network created by the device.

All requests made to the Wibeee's internal server are GET requests and when they have been processed by the server it sends an HTTP correct access response: “HTTP 200 OK”.

5�4�1�- PARAMETER QUERY

5�4�1�1�- DEVICE ID

You should use the following request to view the device's ID:

http://ip_address/services/user/devices.xml

36

Wibeee

Instruction Manual

Figure 42: HPPT queries: Device ID�

5�4�1�2�- Values of the device's variables

To view the values of all of the device's variables, use the following request:

http://ip_address/services/user/values.xml?id=device

Itisalsopossibletoviewspecificvariables,seeTable 11 with the available variables.

http://ip_address/services/user/values.xml?var=device.variable

Figure 43:HPPT queries: Values of the device's variables�

Table 11: Variables table�

Variable Description Units<var>measuresRefresh</var> Measures refresh time of the internal web Seconds<var>appRefresh</var> Time sending data to the server. Minutes<var>softVersion</var> Firmware version of the device -<var>model</var> Modelidentifier -<var>ipAddr</var> Type of IP : DHCP or static IP -<var>gwAddr</var> The device's current IP. -<var>subnetMask</var> Gateway. -


Wibeee

Table 11 (Cont�): Variables table

Variable Description Units<var>primaryDNS</var> Primary DNS server. -<var>secondaryDNS</var> Secondary DNS server. -<var>macAddr</var> MACidentifier -<var>ssid</var> Name of the network. -<var>keyEnc</var> Password type. -<var>keyType</var> Password format: Hex or ASCII -<var>securKey</var> Password. -<var>serverIp</var> Name of the server domain. -<var>serverIpResolved</var> IP address of the server. -<var>serverPort</var> Sending port. -<var>vrms1</var> Phase voltage L1 V<var>vrms2</var> Phase voltage L2 V<var>vrms3</var> Phase voltage L3 V<var>vrmst</var> Total voltage (average of L1, L2, L3) V<var>irms1</var> Current L1 A<var>irms2</var> Current L2 A<var>irms3</var> Current L3 A<var>irmst</var> Total current (average of L1, L2, L3) A<var>pap1</var> Apparent Power L1 VA<var>pap2</var> Apparent Power L2 VA<var>pap3</var> Apparent Power L3 VA<var>papt</var> Total Apparent Power VA<var>pac1</var> Active Power L1 W<var>pac2</var> Active Power L2 W<var>pac3</var> Active Power L3 W<var>pact</var> Total Active Power W<var>preac1</var> L1 Reactive Power Var<var>preac2</var> L2 Reactive Power Var<var>preac3</var> L3 Reactive Power Var<var>preact</var> Total Reactive Power Var<var>freq1</var> Frequency L1 Hz<var>freq2</var> Frequency L2 Hz<var>freq3</var> Frequency L3 Hz<var>freqt</var> Total frequency (average of L1, L2, L3) Hz<var>fpot1</var> Power Factor L1 -<var>fpot2</var> Power Factor L2 -<var>fpot3</var> Power Factor L3 -<var>fpott</var> Total Power Factor -<var>eac1</var> Active Energy L1 Wh<var>eac2</var> Active Energy L2 Wh<var>eac3</var> Active Energy L3 Wh<var>eactt</var> Total Active Energy Wh<var>ereactl1</var> Inductive Reactive Energy L1 VArLh<var>ereactl2</var> Inductive Reactive Energy L2 VArLh

38

Wibeee

Instruction Manual

Table 11 (Cont�): Variables table

Variable Description Units<var>ereactl3</var> Inductive Reactive Energy L3 VArLh<var>ereactlt</var> Total Inductive Reactive Energy VArLh<var>ereactc1</var> Capacitive Reactive Energy L1 VArCh<var>ereactc2</var> Capacitive Reactive Energy L2 VArCh<var>ereactc3</var> Capacitive Reactive Energy L3 VArCh<var>ereactct</var> Total Capacitive Reactive Energy VArCh

5�4�2�- CONFIGURATION

TheminimumrequestsforconfiguringtheWibeee with HPPT are:

1�- DeviceNetworkconfiguration:

http:// ip_address/config_value?name=WIBEEE&dhcp=false&ip=c0a80196&gw=-c0a80101&subnet=ffff0000&id=0.5973659041337669

Table 12: Configuration HPPT variables (Request 1)

Variable Descriptionname Name of the Wibeee

dhcp false: static networktrue: dynamic network

ip IP address in hexadecimalgw Gateway in hexadecimal

subnet Subnet mask in hexadecimal

2�-ConfigurationoftheLocalWi-FiNetwork:

h t t p : / / i p _ a d d r e s s / c o n f i g _ v a l u e ? s s i d = C i r p r o t e c - A l m a c e n & s e c u r i t y = 5 & t y -pekey=2&id=0.5105853546410799


Variable Descriptionssid Name of the Wi-Fi

security Type of security:0: OPEN - 1: WEP - 5:WPA - 9: WPA2 - 13: WPA/WPA2

typekey Password encryption: 1: Hexadecimal - 2: PassPhrase

3�- Password sending:

http://ip_address/config_value?pass=xxxxxxxxx&id=0.9732521877158433


Wibeee


Variable Descriptionpass Wi-Fi password

4�- ServerConfiguration:

http://ip_address/conFigure_server?URLServidor=c339a462&portServidor=1f91&id=0.33531335316222393


Variable DescriptionServerURL Name of the server domainServerport Port in hexadecimal

5�- Resetting the device:

http://ip_address/config_value?reset=true&id=0.03616242413409054

40

Wibeee

Instruction Manual

6�- WIRELESS COMMUNICATIONS

6.1.- USAGE ENVIRONMENT AND HEALTH

Wireless communications emit radio frequency electromagnetic energy, like other radio devic-es.

Because wireless communications operate within the guidelines found in radio frequency safe-ty standards and recommendations, they are safe for users to use.

In certain environments or situations, the use of wireless communications may be restricted by the owner of the building or the representatives responsible for the organisation. These situations include:

The use of wireless connections on board aircraft, in hospitals or near to service stations, blasting areas, medical implants or electronic medical devices implanted in the body (pace-makers etc.).

In any other environment where the risk of interference with other devices or services is identifiedashazardous.

If you are unsure about the policy implemented regarding the use of wireless devices in a spe-cificorganisation(airport,hospital,etc.),itisadvisabletoaskforauthorisationtousewirelesscommunications.

6.2.- Wi-Fi COMMUNICATIONS

Wi-Fi is one of the most widely used wireless technologies today, for connecting and exchang-ing information between electronic devices without having to connect them physically.

The Wibeee has Wi-Fi communications in the 2.4 GHz band, compliant with standard IEEE 802.11

6.3.- MODBUS TCP PROTOCOL

The MODBUS protocol is an industry communication standard that enables the network connection of multiple devices, where there is a master and multiple slaves.

The MODBUS functions implemented in the device are:

Function 0x03. Reading of multiple registers. This function is used to request the desired measurement parameters from the Wibeee Modbus server.

Function 0x05.Writingofaspecificregister.This function isused todelete theWibeee's energy meters.

If the Wibeeereceivesafunctionrequestotherthanthoseabove,orfornon-specifiedmemoryregisters,thedeviceidentifiesthisasan“Illegal error” and responds with the appropriate ex-ception code.


Wibeee

As it is a MODBUS TCP server, the device number internally assigned to the Wibeee is 1.

Bydefault,onceconfigured,theWibeee starts to send data over the internet to the CIRCUTOR server. If you want to stop this data from being sent (for example, because the local network does not have an Internet connection) you have to set a data refresh time of -1. This way, the device is only waiting to handle MODBUS requests.

6.4.- MODBUS MEMORY MAP

All MODBUS map addresses are in hexadecimal format.

Table 16: Modbus memory map

Parameter Symbol Address Units Wibeee model

Phase voltage L1 Vrms1x10 0000 V x 10 Single-phase Three-phase

Phase voltage L2 Vrms2x10 0001 V x 10 Three-phasePhase voltage L3 Vrms3x10 0002 V x 10 Three-phase

Current L1 Irms1x10 0003 A x 10 Single-phase Three-phase

Current L2 Irms2x10 0004 A x 10 Three-phaseCurrent L3 Irms3x10 0005 A x 10 Three-phase

Frequency L1 Freq1x10 0006 Hz x 10 Single-phase Three-phase

Frequency L2 Freq2x10 0007 Hz x 10 Three-phaseFrequency L3 Freq3x10 0008 Hz x 10 Three-phase

Total Frequency FreqTx10 0009 Hz x 10 Single-phase Three-phase

Active Power L1 Wreal1x10 000A W x 10 Single-phaseThree-phase

Active Power L2 Wreal2x10 000B W x 10 Three-phaseActive Power L3 Wreal3x10 000C W x 10 Three-phaseTotal Active Power WrealTx10 000D W x 10 Three-phase

L1 Reactive Power Wreact1x10 000E Var x 10 Single-phase Three-phase

L2 Reactive Power Wreact2x10 000F Var x 10 Three-phaseL3 Reactive Power Wreact3x10 0010 Var x 10 Three-phaseTotal Reactive Power WreactTx10 0011 Var x 10 Three-phase

Apparent Power L1 Waparent1x10 0012 VA x 10 Single-phase Three-phase

Apparent Power L2 Waparent2x10 0013 VA x 10 Three-phaseApparent Power L3 Waparent3x10 0014 VA x 10 Three-phaseTotal Apparent Power WaparentTx10 0015 VA x 10 Three-phase

Power Factor L1 PF1 x 100 0016 x 100 Single-phase Three-phase

Power Factor L2 PF2 x 100 0017 x 100 Three-phasePower Factor L3 PF3 x 100 0018 x 100 Three-phaseTotal Power Factor TPF x 100 0019 x 100 Three-phase

Active Energy L1 Eact1 001A - 001B kWh Single-phase Three-phase

42

Wibeee

Instruction Manual

Table 16 (Cont�): Modbus memory map�Parameter Symbol Address Units Wibeee modelActive Energy L2 Eact2 001C - 001D kWh Three-phaseActive Energy L3 Eact3 001E - 001F kWh Three-phaseTotal Active Energy EactT 0020 - 0021 kWh Three-phase

Inductive Reactive Energy L1 EreactL1 0022 - 0023 kVarh Single-phase Three-phase

Inductive Reactive Energy L2 EreactL2 0024 - 0025 kVarh Three-phaseInductive Reactive Energy L3 EreactL3 0026 - 0027 kVarh Three-phaseTotal Inductive Reactive Energy EreactLT 0028 - 0029 kVarh Three-phase

Capacitive Reactive Energy L1 EreactC1 002A - 002B kVarh Single-phase Three-phase

Capacitive Reactive Energy L2 EreactC2 002C - 002D kVarh Three-phaseCapacitive Reactive Energy L3 EreactC3 002E - 002F kVarh Three-phaseTotal Capacitive Reactive Energy EreactCT 0030 - 0031 kVarh Three-phase

Function 05 is used to delete energy meters.

Table 17:Modbus memory map: Deleting parameters

Deleting parameters Address Value to be sentDeleting energy meters 0000 0xFF00


Wibeee

7�- TECHNICAL FEATURESNote: Themetrologicalspecificationsgivenarealwayswiththerangeofadjustment.

Power supply

Rated VoltageWibeee-M-x , Wibeee-T-x(1) Wibeee-3P(1)

85 to 265 V ~ 105... 440 V ~ (Ph-Ph)

Frequency 50 ... 60 Hz 50 ... 60 HzConsumption 1.5... 4.5 VA 3.5... 5.5 VA

(1) The Wibeee-T model is powered between L1 and N. The WiBeee-3P model is powered between L2 and L3.Voltage measurement circuit

Voltage measurement marginWibeee-M-x , Wibeee-T-x Wibeee-3P

85 to 265 V ~ 105... 440 V ~ (Ph-Ph)

Frequency measurement margin 50 ... 60 Hz 50 ... 60 HzMin� voltage measurement (Vstart) 85 V 100 VInstallation category CAT III CAT III

Current measurement circuit

Current measurement marginWibeee-M-x , Wibeee-T-x Wibeee-3P

1 ... 65 A 1... 65 AMin� current measurement (Istart) 500 mA 500 mAInstallation category CAT III CAT III

Measurement accuracy Voltage measurement 2 % + variations in range of use (at PF = 1)Current measurement 2 % + variations in range of use Power measurement 4 % + variations in range of use

Variations in Range of UseMagnitude of influence Range of influence Typical MaximumTemperature - 10ºC ... +45ºC - 0.3 %Relative humidity 10% ... 90% - 0.3 %Crosstalk (current) - 0.9 % -External demagnetising field (current) - 1 % -Conductor position - 2 % 3 %Adjust Full Scale 0.2 % 0.4 %Distance between wire and sensor - 2.5% / 0.1 mm -

CommunicationsType Wi-Fi (IEEE 802.11)Protocol HTTP, Modbus/TCP, XMLFrequency Range 2.405 - 2.48 GHzEncryption AES128Monthly data consumption 300 MBFCC(USA),IC(CANADA),ETSI(EUROPA)Certified

User interfaceLED 2 LEDsButton 1 button Mobile application Wibeee Circutor

44

Wibeee

Instruction Manual

Environmental featuresOperating temperature -10ºC ... +45ºCStorage temperature -40ºC ... +85ºCRelative humidity (without condensation) 10 ... 90%Maximum altitude 2000 mProtection degree IP20Insulation Double insulation

Mechanical features

Dimensions (mm)Wibeee-M-x Wibeee-T-x Wibeee-3P

Figure 44 Figure 45 Figure 46Weight 37 g 64 g 53 gSurround Self-extinguishing VO Plastic (UNE 21031 90ºC)

4950,5

28

20

22

Figure 44: Dimensions : Wibeee-M-L and Wibeee-M-R�

8050,5

28

20

22

Figure 45: Dimensions : Wibeee-T-L y Wibeee-T-R�

47,87

53,4049

Figure 46: Dimensions : Wibeee-3P�


Wibeee

StandardSafety requirements for electrical equipment for measurement, control and laboratory use -- Part 2-030: Particular requirements for testing and mea-suring circuits

UNE-EN 61010-2-030

Electrical equipment for measurement, control and laboratory use - EMC requirements -- Part 1: General requirements (IEC 61326-1:2005) UNE-EN 61326-1

Electromagnetic compatibility and Radio spectrum Matters (ERM); Elec-troMagnetic Compatibility (EMC) standard for radio equipment; Part 17: Specific conditions for Broadband Data Transmission Systems

EN 301 489-17 V2�2�1�

46

Wibeee

Instruction Manual

8�- MAINTENANCE AND TECHNICAL SERVICE

9�- WARRANTY

In the case of any query in relation to device operation or malfunction, please contact the CIRCUTOR, SA Technical Support Service.

Technical Assistance ServiceVial Sant Jordi, s/n, 08232 - Viladecavalls (Barcelona)Tel: 902 449 459 ( España) / +34 937 452 919 (outside of Spain)email: [email protected]

• No returns will be accepted and no unit will be repaired or replaced if it is not ac-companied by a report indicating the defect detected or the reason for the return.•The guarantee will be void if the units has been improperly used or the stora-ge, installation and maintenance instructions listed in this manual have not been followed.“Improperusage”isdefinedasanyoperatingorstorageconditioncon-trary to the national electrical code or that surpasses the limits indicated in the technical and environmental features of this manual.• CIRCUTOR accepts no liability due to the possible damage to the unit or other parts of the installation, nor will it cover any possible sanctions derived from a pos-siblefailure,improperinstallationor“improperusage”oftheunit.Consequently,this guarantee does not apply to failures occurring in the following cases:- Overvoltages and/or electrical disturbances in the supply;-Water,iftheproductdoesnothavetheappropriateIPclassification;- Poor ventilation and/or excessive temperatures;- Improper installation and/or lack of maintenance;-Buyerrepairsormodificationswithoutthemanufacturer’sauthorisation.

CIRCUTOR guarantees its products against any manufacturing defect for two years after the delivery of the units.

CIRCUTOR will repair or replace any defective factory product returned during the guarantee period.


Wibeee

10�- CE CERTIFICATE

48

Wibeee

Instruction Manual


Wibeee

CIRCUTOR, SA Vial Sant Jordi, s/n08232 - Viladecavalls (Barcelona)Tel.: (+34) 93 745 29 00 - Fax: (+34) 93 745 29 14 www.circutor.com [email protected]

Date post:	25-Jul-2020
Category:	Documents
Upload:	others
View:	0 times
Download:	0 times

INSTRUCTION MANUAL - CIRCUTORdocs.circutor.com/docs/M064B01-03.pdf · Instruction Manual 7 Wibeee 1...

Documents