timberwolf-uk.com
INSTRUCTION MANUAL
TW S426TDHB SHREDDER
© Copyright Entec Industries Ltd 2015
The content of this publication may not be copied, reproduced, republished, posted, broadcast, transmitted
or used in any way in any medium without the written permission of Entec Industries Ltd.
CONTENTS TIMBERWOLFTW S426TDHB
Section Page No.
INTRODUCTION 1PURPOSE OF MACHINE 2MACHINE DIMENSIONS & SPECIFICATIONS 2PARTS LOCATION DIAGRAMS 4SAFE WORKING 6
Operator’s Personal Protective Equipment Required 6Basic Shredding Safety 6General Safety Matters - Do’s and Dont’s 7Noise Test 8
OPERATING INSTRUCTIONS 9Safe Transportation 9Hitching onto the Tow Ball 9Unhitching the Shredder 9Delivery 10Operator’s Personal Protective Equipment Required 10Manual Controls 10Auto Controls 11Daily Checks Before Starting 11Engine Controls 11Starting the Engine 11Controlling the Engine Speed 11Stopping the Engine 12Before Using the Shredder 12Starting to Shred 12Discharge Controls 12Hydraulic Oil Lever Indicator 13Fuel Level Indicator 13Shredding 13Blockages 13
SERVICE INSTRUCTIONS 14Service Schedule 15Safe Maintenance 16Spares 16Safe Lifting of the Shredder 16Change Hydraulic Oil and Filter 16Copper Ease Safety Information 17Battery Removal and Maintenance 17Battery Safety Information 17Check Fittings 19Check Free Rotation of Drum and Hammers 19Change Hammers 20Check Hoses 20Grease Drum Bearings 21Tension Drive Belts 21Grease the Roller Box Slide 22Grease the Roller Spline and Bearing 22Grease Jack Stand 22Grease the Discharge Flange 22Engine Manufacturer’s Handbook 22
WARRANTY STATEMENT 23EC DECLARATION OF CONFORMITY CERTIFICATE 24IDENTIFICATION PLATES 25DECALS 26ELECTRICAL DETAIL 28HYDRAULIC LAYOUT 29CIRCUIT DIAGRAM 30V- BELT TENSIONING TABLE 31PARTS LISTS 32WARRANTY SERVICE CHECK RECORD 49SERVICE RECORD 50 10.04.2017
TIMBERWOLFTW S426TDHB1
Thank you for choosing this Timberwolf shredder. Timberwolf shredders are designedto give safe and dependable service if operated according to the instructions.
IMPORTANT HEALTH AND SAFETY INFORMATIONBefore using your new shredder, please take time to read this manual. Failure to doso could result in:
- PERSONAL INjURY- EqUIPMENT DAMAGE- DAMAGE TO PROPERTY - 3RD PARTY INjURY
This manual covers the operation and maintenance of the Timberwolf TW S426TDHB.All information in this manual is based on the latest product information available at thetime of purchase.
All the information you need to operate the machine safely and effectively is containedwithin pages 2 to 13. Ensure that all operators are properly trained for operating thismachine, especially safe working practices.
Timberwolf's policy of regularly reviewing and improving their products may involve majoror minor changes to the shredders or their accessories. Timberwolf reserves the rightto make changes at any time without notice and without incurring any obligation.
Due to improvements in design and performance during production there may be (insome cases) minor discrepancies between the actual shredder and the text in this manual.
The manual should be considered an important part of the machine and should remain with it if the machine is resold.
CAUTION or WARNINGBE AWARE OF THIS SYMBOL AND WHERE
SHOWN, CAREFULLY FOLLOW THE INSTRUCTIONS.
This caution symbol indicates important safety messages in this manual.When you see this symbol, be alert to the possibility of injury to yourselfor others and carefully read the message that follows.
ALWAYS FOLLOW SAFE OPERATING AND MAINTENANCE PRACTICES
INTRODUCTION
PH
TIMBERWOLF TW S426TDHB SPECIFICATIONEngine type Kubota 4-cylinder turbo dieselMaximum power 33kW (45hp)Cooling method Water cooledOverall weight 1350kgStarting method ElectricRoller feed Hydraulic motor
Feed roller opening 426mm (17”) x 230mm (9")Fuel capacity 33 litresHydraulic oil capacity 15 litresMaterial processing capacity up to 3 tonnes/hrFuel type Diesel
The Timberwolf TW S426TDHBThe Timberwolf S426TDHB is a high speed, heavy duty professional shredder. It is designed to shred generalgreen waste (brash, prunings, hedge trimmings, Leylandii, Christmas trees, rootballs, etc.),brushwood up to100mm (4”), pallets, domestic doors, wooden and plastic window frames (all pre-cut to fit feed aperture),contaminated timber, chipboard, MDF, packaging materials, uPVC plastic, cardboard, wooden furniture, fenceposts and similar items. The machine will tolerate drinks cans, plastic bottles, stones, rocks and concrete (upto fist size), nails, metal door furniture, glass bottles and similar items.
TIMBERWOLF
TW S426TDHB
To properly control the speed of material entering the shredder chamber, the machine relies on the large feedroller to grip the material. The feed roller can grip material down to 15mm in diameter. The machine will nottolerate or process items such as tyres, mattresses, heavy duty plastic containers (used for oils, chemicals,etc.), carpets, reinforced concrete, metallic items exceeding lightweight domestic door furniture, commercialplastic gas pipe, alkathene water pipe, metal reinforced drainage/irrigation pipe, baler twine, rope, metalbanding, computer hard drives (which contain magnets) and any similar objects to the above.
NOTE: When materials are corrosive they may attack and degrade the individual components. It is essential thatthe unit be thoroughly cleaned down after shredding anything that may contain materials of an aggressive nature.
Ejection of material – Warning! The S426TDHB shredder ejects material at high speed. Ensure there is anadequate safety zone and that ejected material is aimed away from operators into a safe area, i.e. anenclosure or container with a back stop (i.e. wall) behind it to prevent ejected material from leaving the workarea and causing injury and damage. If loading into a truck or trailer, ensure the structure is strong enough tocope with the impact from ejected material.
DIMENSIONSSerial No. Location
The serial number can be foundon the identification platelocated on the chassis beam.
Towing Length: 3600mm, Working Length with standard tow head: 4220mm
1506mm
2220
mm
, (16
75m
m w
ithdi
scha
rge
rem
oved
)
WARNING LIMITATIONS ON MATERIALS
2TIMBERWOLFTW S426TDHB
The TW S426TDHBA shredder has the ability to adjust the towhead height to correspond with thevehicles towing point.
The preferred towing angle of any shredder is with thechassis level to the ground. The adjustable head hasthe ability to move between 300mm from the groundto 875mm giving an overall adjustment of 575mm.
The towhead latch and handbrake fundamentallywork the same as a fixed standard towhead, howeverthe front section of the head is retained in position viaa locking ring and single clamp handle.To adjust the height the locking handle located on theside of the head (1) is turned in an anticlockwisedirection to allow for the locking ring to disengagefrom its apposing ring. An internal damper is fitter tosupport the heads weight allowing both hands free toadjust the height. Once the desired height has beenachieved the locking handle is turned clockwise until
tight. The latching of the hitch is as normal as is the fitting of the light plug and breakaway cable asoutlined in the ‘Hitching onto the tow ball’ section on page 9.
1
Engine type Kubota 4-cylinder turbo dieselMaximum power 33kW (45hp)Cooling method Water cooledOverall weight 1415kgStarting method ElectricRoller feed Hydraulic motor
Maximum diameter material 225mm (9")Fuel capacity 33 litresHydraulic oil capacity 15 litresMaterial processing capacity up to 3 tonnes/hrFuel type Diesel
TIMBERWOLF TW S426TDHBA SPECIFICATION
DIMENSIONS
Serial No. LocationThe serial number can be foundon the identification platelocated on the chassis beam.
2220
mm
, (16
75m
m w
ithdi
scha
rge
rem
oved
)
1506mm
Towing Length: 4650mm, Working Length with adjustable tow head: 5270mm
ADJUSTING THE TOWHEAD HEIGHT
3 TIMBERWOLFTW S426TDHB
TIMBERWOLF
TW S426TDHB
PH TIMBERWOLFTW S426TDHB 4
FEED
FU
NN
EL
DIS
CH
AR
GE
TUB
E
DIS
CH
AR
GE
BU
CK
ET
SAFE
TY B
AR
DR
UM
HO
USI
NG
FUEL
TA
NK
ENG
INE
GU
AR
D
TOW
HEA
D(F
IXED
TOW
HEA
DSH
OW
N)
RO
LLER
CO
N-
TRO
LS
DIS
CH
AR
GE
AD
jUST
MEN
TC
ON
TRO
LA
IR IN
TAK
E
EXH
AU
ST
FEED
TR
AY
TIM
BER
WO
LF
TW S
426T
DHB
SPA
RE
WH
EEL
CLE
AR
ING
PLAT
E
REF
LEC
TOR
SR
AIN
FLA
PS
REF
LEC
TOR
S
PARTS LOCATOR
jOCKEYWHEEL
ASSEMBLY
BATTERY DRUM
PULLEYDRIVE
PULLEY
FUELPUMP
DIPSTICK
OIL FILTER
ALTERNATOR
ENGINECONTROL PANEL
STARTERMOTOR
RADIATORTOP ROLLERSLIDE
DIRECTIONALCONTROL
VALVE
RESERVE TANK
HYDRAULICOIL TANK
HYDRAULICOIL FILTER
MOTOR
DRUM
HAMMERS
THROTTLE
TIMBERWOLFTW S426TDHB5 SAFE WORKING
PARTS LOCATOR
PHSAFE WORKING
BASIC SHREDDING SAFETY
WARNINGThe shredder will feed material through on its own. To do this, it relies onthe hammers to be free to swing. DO NOT put bricks, large stones, string,carpet, tyres or metal into the shredder.
OPERATOR'S PERSONAL PROTECTIVE EQUIPMENT REQUIRED
Chainsaw safety helmet fittedwith mesh visor and recommended ear defenders tothe appropriate specifications.
Work gloves with elasticatedwrist.
Close fitting heavy-dutynon-snag clothing.
Face mask if appropriate.
DO NOTwear rings, bracelets, watches,jewellery or any other items thatcould be caught in the materialand draw you into the shredder.
Steel toe cap safety boots.
6TIMBERWOLFTW S426TDHB
The operator should be aware of the following points:
MAINTAIN A SAFETY EXCLUSION ZONE around the shredder of at least 10 metres for thegeneral public or employees without adequate protection. Due to the nature of material beingshredded and the distance/velocity of discharge, the exclusion zone must be extended to 20metres in front of the discharge tube exit. Use hazard tape to identify this working area and keepit clear from debris build up. Shredded material should be ejected away from any area thegeneral public have access to.
HAZARDOUS MATERIAL - Some species of trees and bushes are poisonous. The shreddingaction can produce vapour, spray and dust that can irritate the skin. This may lead torespiratory problems or even cause serious poisoning. Check the material to be shreddedbefore you start. Avoid confined spaces and use a facemask if necessary.
BE AWARE when the shredder is processing material that is an awkward shape. The materialcan move from side to side in the funnel with great force. If the material extends beyond thefunnel, the brash may push you to one side causing danger.
BE AWARE that the shredder can eject material out of the feed funnel with considerable force.Always wear full head and face protection.
ALWAYS work on the side of the machine furthest from any local danger, e.g. not road side.
ü
SAFE WORKING
GENERAL SAFETY MATTERSD O ’ S A N D D O N ’ T S
ALWAYS stop the shredder engine before making any adjustments, refuelling or cleaning.
ALWAYS check machine has stopped rotatingand remove shredder ignition key before maintenance of any kind, or whenever the machine is to be left unattended.
ALWAYS check machine is well supported andcannot move.
ALWAYS run with the engine set to maximumspeed.
ALWAYS check (visually) for fluid leaks.
ALWAYS take regular breaks. Wearing personalprotective equipment for long periods can be tiring and hot.
ALWAYS keep hands, feet and clothing out offeed opening, discharge and moving parts.
ALWAYS use the next piece of material or apush stick to push in short pieces. Under no circumstances should you reach into the funnel.
WAYS keep the operating area clear of people,animals and children.
ALWAYS keep the operating area clear from debris build up.
ALWAYS keep clear of the chip discharge tube.Foreign objects may be ejected with great force.
ALWAYS ensure protective guarding is in placebefore commencing work. Failure to do so mayresult in personal injury or loss of life.
ALWAYS use shredder in a well ventilated area -exhaust fumes are dangerous.
ü
DO NOT use shredder unless available light issufficient to see clearly.
DO NOT use or attempt to start the shredderwithout the feed funnel, belt guard, guards anddischarge unit securely in place.
DO NOT start the shredder running unlessproperly guarded.
DO NOT stand directly in front of the feed funnelwhen using the shredder. Stand to one side.
DO NOT allow -
DO NOT smoke whenrefuelling. Petrol/diesel fuel isexplosive!
DO NOT let anyone who hasnot received instruction operate the machine.
DO NOT climb on the machine at any time.
DO NOT handle material that is partially engagedin the machine.
DO NOT touch any exposed wiring while machineis running.
DO NOT use the shredder inside buildings.
- to enter the machine, as damage is likely.
BRICKS STRING METAL
CLOTH OR CARPET
RUBBER LARGESTONES
7 TIMBERWOLFTW S426TDHB
PHSAFE WORKING 8TIMBERWOLFTW S426TDHB
NOISE TESTMACHINE: TW S426TDHB & TW S426TDHBANOTES: Tested shredding 120mm x 120mm corsican pine 1.5m
in lengthNoise levels above 80dB (A) will be experienced at the working position. Wear ear protectionat all times to prevent possible damage to hearing. All persons within a 4 metre radius must alsowear good quality ear protection.
95.1 dB94.8 dB
97.2 dB96.6 dBR= 4 metres
Guaranteed Sound Power: 120dB (A)
100.7 dB
95.1 dB
As required by Annex III of Directive 2000/14/EC “Noise Emission in the environment by equipment for use outdoors”.
R= 10 metres
90.9
dBC
alcu
late
d
90.9dB Calculated
90.9dB Calculat
ed
TIMBERWOLFTW S426TDHB9 OPERATING INSTRUCTIONS
• CHECK ball head is well greased.• WIND jockey wheel assembly anticlockwise until
the tow head is above the height of the ball hitch on the vehicle.
• REVERSE vehicle so the ball hitch is directly belowthe tow head.
• ATTACH breakaway cable to a strong point on the vehicle, not the ball hitch.
• GRASP handle on tow head and push back catch with thumb.
• WIND jockey wheel assembly clockwise, to lower the tow head onto the ball hitch.
• RELEASE handle and continue to wind jockey
wheel clockwise. The tow head should snap into place on the ball hitch. If it doesn't, repeat previous 2 steps.
• WIND jockey wheel up until fully retracted and the jockey wheel frame is seated in its notch on the stem. The chipper weight should be fully on the vehicle.
• RELEASE jockey wheel clamp and slide the jockeywheel assembly fully up.
• TIGHTEN clamp on jockey wheel assembly.• CONNECT electrical plug to socket on rear of
towing vehicle and check operation of all the trailer and vehicle lights.
• THE shredder is now properly attached to the vehicle.
WARNINGDO NOT RIDE ON THE
SHREDDER WHEN IT ISBEING TOWED.
HITCHING ONTO THE TOW BALL
When the shredder is unhitched it should be made secure before starting work by applying the handbrakeand lowering the prop stand and jockey wheel (b).
When hitched to a vehicle the shredder handbrakeshould be released and the prop stand and jockeywheel stored in the towing position (a).
• APPLY handbrake. • DISCONNECT the electrical cable from the
vehicle socket.• RELEASE breakaway cable.• RELEASE the jockey wheel assembly clamp.• LOWER the jockey wheel assembly fully.• RETIGHTEN the jockey wheel assembly clamp.• WIND the jockey wheel assembly anticlockwise
until it starts to take the weight of the shredder.
• GRASP the handle and release the catch with your thumb.
• CONTINUE to wind the jockey wheel anticlockwise. This should lift the tow head clear of the ball hitch.
• DRIVE the vehicle clear of the shredder.• WIND the jockey wheel assembly to a suitable
point where the shredder is level.• THE shredder is now fully detached from the
vehicle.
• WHEN towing a shredder the maximum speed limitis 60 mph (100 kph).
• ON rough or bumpy road surfaces reduce speed accordingly to protect your machine from unnecessary vibration.
• WHEN towing off road be aware of objects that may catch the shredder undergear.
• WHEN towing off road ensure inclination is not excessive.
• AVOID excessively pot holed ground.
• WHEN reversing the shredder the short wheel base will react quickly to steering.
• ALWAYS check the discharge is tight before moving.• KEEP tyre pressures inflated to 2.9 bar or 42 psi.• CHECK wheel nuts are tightened to 90Nm (65 lbs ft).• CLEAR loose shreddings and debris from the
machine before departing.• ENSURE safety bar catch is properly engaged
before departing
(a) (b)
SAFE TRANSPORTATION
UNHITCHING THE SHREDDER
STABILISING THE SHREDDER
OPERATING INSTRUCTIONS
CHAINSAW safety helmet fitted with visorand recommended ear defenders to an appropriate specification.HEAVY-DUTY gloves with elasticated wrist area.
CLOSE - FITTING heavy-duty non-snag clothing.
SAFETY footwear.
FACE MASK (if appropriate).
See page 6 for more detailed information.
DELIVERY
OPERATOR’S PERSONAL PROTECTIVE EQUIPMENT REQUIRED
MANUAL CONTROLS
All Timberwolf S426TDHB & S426TDHBA machines have a full pre - delivery inspection beforeleaving the factory and are ready to use. Read and understand this instruction manual beforeattempting to operate the shredder. In particular, read pages 6-8 which contain important health andsafety information and advice.
Roller control boxes- two control boxes are located on either side of the feed tray. Their function is tocontrol the feed roller that draw material into the machine. They do not control the main drum.
RED SAFETY BAR = This is the large red bar that surrounds the feed tray and side of the feedfunnel. The bar is spring loaded and connected to a switch that will interrupt the power to the roller. Theswitch is designed so that it only activates if the bar is pushed to the limit of its travel. The roller willstop instantly, but can be made to turn again by pressing either the GREEN FEED or BLUE REVERSEcontrol buttons.
WARNING DO NOT remove, jam, disable, bypass, override or otherwiseimpede the effectiveness of the red safety bar.
GREENFORWARD
FEEDPANEL
BLUE REVERSE
FEEDPANEL
RED SAFETY BAR
Control Box Diagram
Do not rely on the red bar to keep the rollerstationary if it is necessary to clear or touch theroller. Always switch off the machine and removeignition key before approaching the roller.
There are two control boxes, located oneither side of the feed tray.
RED SAFETY BAR TESTTo ensure the safety bar is always operational it must be activated once before each work session.The rollers will not function until the bar is activated. This procedure must be repeated each time theignition is switched off.
GREEN BUTTON = Forward feed - Push the button once - this activates the roller and will allow you tostart shredding (if the drum speed is high enough).
BLUE BUTTON = Reverse feed - allows you to back material out of the roller. The roller will only turnin reverse as long as you keep pressing the button.
10TIMBERWOLFTW S426TDHB
OPERATING INSTRUCTIONS
LOCATE the machine on firm level ground.CHECK machine is well supported and cannot move.CHECK jack stand is lowered and secure.CHECK all guards are fitted and secure.CHECK the discharge unit is in place and fastened securely. CHECK discharge tube is pointing in a safe direction. CHECK the feed funnel to ensure no objects are inside.CHECK feed tray is in up position - to prevent people reaching the roller.CHECK for free rotation of drum and hammers (see instructions on page 19).CHECK controls as described below.CHECK (visually) for fluid leaks.CHECK fuel and hydraulic oil levels.
For parts location see diagrams on pages 4 & 5
The engine management unit controls the feed rate of the material going into the shredding chamber.If the engine speed is below the predetermined level, the engine management unit will not allow the feedroller to work in the forward “infeed” direction, until the drum speed rises above the predetermined level.At this point, the feed roller will start turning without warning. The reverse function will work at anyengine speed.
AUTO CONTROLS
DAILY CHECKS BEFORE STARTING
ENSURE throttle lever is in the slow (tortoise) position.INSERT key. Turn to heat.HEATER LED comes on. WAIT FOR HEATER LED TO GO OUT.TURN key to engage starter motor.RELEASE key once engine starts.
Do not engage starter motor for more than 20 seconds- allow one minute before attempting to start. Investigatereasons for failure to start.
The engine controls are in two locations. The engine ignition is on thecontrol panel in the centre of the machine, and the throttle lever is on thebonnet (see parts locator on page 5).
The engine has two throttle settings, idle and fast. These are controlled by thethrottle lever on the bonnet. Moving the lever towards the ‘Hare’ on the pictogramwill increase engine speed while moving it towards the ‘Tortoise’ will decrease theengine speed.
HOURSCOUNTER
POWERON / OFF& START
POWERON LED
1 4 6 2 9 7 5
HEATERON LED
01 2
STARTHEATOFF ON
1 20
ENGINE CONTROLS
11 TIMBERWOLFTW S426TDHB
STARTING THE ENGINE
CONTROLLING ENGINE SPEED
H
DISCHARGE CONTROLS
STOPPING THE ENGINE
STARTING TO SHRED
IT IS ESSENTIAL TO CARRY OUT THE FOLLOWING TESTS to check safety equipment - this sequenceof tests will only take a few seconds to carry out. We recommend that these tests are carried out daily.Observing the function as described will confirm that the safety circuits are working correctly. This is alsoa good opportunity to remind all operators of the control and emergency stop systems.
31 2PRESS THE GREEN BUT-
TON THE ROLLER
SHOULD TURN FORWARDS
PRESS THE REDSAFETY BARTHE ROLLER
SHOULD STOP
PRESS THE BLUE BUTTON THE ROLLER SHOULD TURN
BACKWARDS ONLY WHILE THEBUTTON IS PRESSED
WITH THE ENGINE RUNNING AT FULL SPEED
MOVE the throttle lever to the ‘Tortoise’ to reduce the engine speed to idle.LEAVE the engine running for 1 minute.TURN the power switch to position 0. The engine should stop after a few seconds.AT the end of operations allow sufficient time for all shredded material to be ejected from thedischarge before switching off.
CHECK that shredder is running smoothly.RELEASE the catches on the feed tray and lower. PRESS the green control button. The roller will commence turning. STAND to one side of the feed funnel.PROCEED to feed material into the feed funnel. AT the end of operations allow sufficient time for all shredded material to be ejected from the dis-charge before switching off.
Controlling the discharge is an essential part of safe working.ROTATION
Slacken nut ‘C’ using integral handle, rotate tube, retighten nut.BUCKET ANGLE
Adjust the bucket to the desired angle by loosening clamp ‘A’ and pushing/pulling handle ‘B’. When angle achieved retighten clamp ‘A’.NOTE: Handle ‘B’ can be positioned in either upper or lower holes according to operator preference.
CLEARING PLATEUnclip catches ‘D’ on both sides to open the clearing plate.
C
D
AB
BEFORE USING THE SHREDDER
WARNINGDo not use or attempt to start the shredder without the protectiveguarding and discharge unit securely in place. Failure to do so mayresult in personal injury or loss of life.
12TIMBERWOLFTW S426TDHBOPERATING INSTRUCTIONS
HYDRAULIC OIL LEVEL INDICATOR
Always be aware that what you are putting into the shredder must come out. If the material stops coming out ofthe discharge tube but the shredder is taking material in - STOP IMMEDIATELY. Continuing to feed material intoa blocked machine may cause damage and will make it difficult to clear. Two areas of the machine can becomeblocked - the discharge tube and the drum housing. To clear a blockage proceed as follows:
Continuing to feed the shredder with material once it has become blocked will cause the shredder tocompact material in the drum housing and discharge chute and it will be difficult and time consumingto clear.
AVOID THIS SITUATION - WATCH THE DISCHARGE TUBE AT ALL TIMES.
STOP the engine and remove the keys.
REMOVE the two drum housing securing nuts and open the drum housing until it rests against therubber stop. WARNING! Ensure the weight of the discharge tube is fully supported whilst opening the drum housing, to avoid injury and damage.
REMOVE any blockage from the discharge tube, ensuring that it is clear along its entire length.
WEARING gloves, reach into the drum housing and remove the material causing the blockage, including any material that may have also entered the side fan casing. WARNING! Beware of turning the drum whilst clearing a blockage, as this could lead to injury.
CLOSE the drum housing and replace and tighten the two securing nuts. WARNING! Ensure the weight of the discharge tube is fully supported whilst lowering the drum housing, to avoid injury and damage.
RESTART the engine and increase to full throttle. Allow sufficient time for the machine to clear any residual material before recommencing work.
This can be viewed through the wall of the tank. Maximum and minimum marks are provided.
The fuel level can be seen through the tube fitted to the side of the tank.
To properly control the speed of material entering the shredder chamber, the machine relies on the large feedroller to grip the material. The feed roller can grip material down to 15mm in diameter. The machine will nottolerate or process items such as tyres, mattresses, heavy duty plastic containers (used for oils, chemicals,etc.), carpets, reinforced concrete, metallic items exceeding lightweight domestic door furniture, commercialplastic gas pipe, alkathene water pipe, metal reinforced drainage/irrigation pipe, baler twine, rope, metalbanding, computer hard drives (which contain magnets) and any similar objects to the above.
NOTE: When materials are corrosive they may attack and degrade the individual components. It is essential that theunit be thoroughly cleaned down after shredding anything that may contain materials of an aggressive nature.
Ejection of material – Warning! The TW S426TDHB / TW S426TDHBA shredder ejects material at high speed.Ensure there is an adequate safety zone and that ejected material is aimed away from operators into a safe area,i.e. an enclosure or container with a back stop (i.e. wall) behind it to prevent ejected material from leaving thework area and causing injury and damage. If loading into a truck or trailer, ensure the structure is strong enoughto cope with the impact from ejected material.
FUEL OIL LEVEL INDICATOR
SHREDDING
WARNING LIMITATIONS ON MATERIALS
BLOCKAGES
13 TIMBERWOLFTW S426TDHBOPERATING INSTRUCTIONS
THE FOLLOWING PAGES DETAIL ONLY BASIC MAINTENANCE GUIDELINES SPECIFIC
TO YOUR SHREDDER.
THIS IS NOT A WORKSHOP MANUAL.
THE FOLLOWING GUIDELINES ARE NOT EXHAUSTIVE AND DO NOT EXTENDTO GENERALLY ACCEPTED STANDARDS OF ENGINEERING/MECHANICAL
MAINTENANCE THAT SHOULD BE APPLIED TO ANY PIECE OF MECHANICALEQUIPMENT AND THE CHASSIS TO WHICH IT IS MOUNTED.
AUTHORISED TIMBERWOLF SERVICE AGENTS ARE FULLY TRAINED IN ALLASPECTS OF TOTAL SERVICE AND MAINTENANCE OF TIMBERWOLF
SHREDDERS. YOU ARE STRONGLY ADVISED TO TAKE YOUR SHREDDER TOAN AUTHORISED AGENT FOR ALL BUT THE MOST ROUTINE MAINTENANCE
AND CHECKS.
TIMBERWOLF ACCEPTS NO RESPONSIBILITY FOR THE FAILURE OF THEOWNER/USER OF TIMBERWOLF SHREDDERS TO RECOGNISE GENERALLYACCEPTED STANDARDS OF ENGINEERING/MECHANICAL MAINTENANCE
AND APPLY THEM THROUGHOUT THE MACHINE.
THE FAILURE TO APPLY GENERALLY ACCEPTED STANDARDS OF MAINTENANCE, OR THE PERFORMANCE OF
INAPPROPRIATE MAINTENANCE, MAY INVALIDATE WARRANTY IN WHOLE OR IN PART.
PLEASE REFER TO YOUR AUTHORISED TIMBERWOLF SERVICE AGENT FOR
SERVICE AND MAINTENANCE.
PH TIMBERWOLFTW S426TDHB 14SERVICE INSTRUCTIONS
TIMBERWOLFTW S426TDHB15 SERVICE INSTRUCTIONS
WARNINGAlways immobilise the machine by stopping the engine, removingthe ignition key and disconnecting the battery before undertakingany maintenance work.
SERVICE SCHEDULE
SERVICE SCHEDULE
Check water. üCheck engine oil - top up if necessary (10W-30). üCheck for engine oil / hydraulic oil leaks. üCheck tyre pressure is 2.9 Bar (42 psi). üCheck feed funnel, feed roller cover, access covers, engine covers and discharge unit are securely fitted. üCheck for free rotation of drum and hammers. üCheck air intake is clear. üClean air filter element.Grease the drum bearings.
Grease the roller box slides. üGrease the roller spline and bearing. üCheck for tightness all nuts, bolts and fasteningsmaking sure nothing has worked loose. üCheck tension of main drive belts (and tension if necessary). üGrease discharge flange. üCheck anvil for wear. üGrease jack stand. üCheck battery electrolyte level. üCheck for loose electrical wiring. üReplace hydraulic oil filter - every year or 100 hours after service or repair work to the hydraulic system. ü üReplace hydraulic oil. ü üService tow head/adjustable tow head.Axle maintenance.Road brake maintenance.Replace anvil when worn.
DailyCheck
50Hours
100Hours
500Hours
1Year
RETURN TO DEALER FOR ANVIL CHANGE
OROR
SEE MANUFACTURERS
SHEET FOR DETAILS
OR AS REqUIRED - SEE PAGE 22OR AS REqUIRED - SEE PAGE 22
GREASE DAILY OR AS REqUIRED WITH INFREqUENT USE - SEE PAGE 21
DEPENDING ON WORKING ENVIRONMENT
NOTE: Your Timberwolf shredder is covered by a full 12 months parts and labour warranty. Subject tocorrect maintenance and proper machine usage, the bearings are guaranteed for 12 monthsregardless of hours worked by the machine. In conditions of 'heavy usage' - i.e. in excess of 500 hoursper year - it is recommended that the bearings are changed annually to ensure that the machine retainsoptimum working performance.
SAFE MAINTENANCE
WARNINGUse plastic gloves to keep oil off skin and dispose of the used oiland filter in an ecologically sound way. The oil and filter should bechanged once a year or at any time it becomes contaminated.Before starting check that the shredder is standing level and theengine is cool.
CHANGE HYDRAULIC OIL AND FILTER
PH TIMBERWOLFTW S426TDHB 16SERVICE INSTRUCTIONS
HANDLE hammers with extreme caution to avoid injury. Gloves should always be worn when handling the hammers.THE drive belts should be connected while changing blades, as this will restrict sudden movement of the drum.
THE major components of this machine are heavy. Lifting equipment must be used for disassembly. CLEAN machines are safer and easier to service. AVOID contact with hydraulic oil and fuel.
Only fit genuine Timberwolf replacement screws and shredder spares. Failure to do so willresult in the invalidation of the warranty and may result in damage to the shredder, personalinjury or even loss of life.
1. Remove the side panel.2. Remove the black screw cap from the top of the filter housing.3. Partially remove filter element from inner cup. Leave filter to
drain for 15 minutes.4. Remove filter element from cup when clear of hydraulic oil.5. Remove drain plug and drain oil into a suitable container.6. Replace drain plug.7. Refill with VG 32 hydraulic oil until the level is between the min and
max lines marked on the tank (about 15 litres).8. Refit the filter cup, install a new filter element and refit the
black screw cap to the filter housing, ensuring o-ring remains in place.
3
2
ALWAYS IMMOBILISE THE ENGINE BEFORE UNDERTAKING ANY MAINTENANCE WORK ON THESHREDDER BY REMOVING THE KEY AND DISCONNECTING THE NEGATIVE LEAD AT THE BATTERY.
21 320o
39o
DO NOT use handgrabs for lifting.
3500mm
2200
mm
SAFE LIFTING OF THE SHREDDER
SPARES
Use slings rated at 2000kg each for the lifting procedure.Lift from lugs (No. 1 & 2), using correctly rated ‘D’shackles with slings approx 1500mm long giving anincluded angle of 20o (rear view). Pass a third sling under chassis beams around thetowhead (3). The length of this rigged sling should beapprox. 7000mm. The ideal lift angle of these combinedslings is 39o (side view).Ensure area is clear of bystanders when lifting and donot walk/crawl under shredder when raised from floor.
TIMBERWOLFTW S426TDHB17 SERVICE INSTRUCTIONS
For safety reasons, wear eye protection when handling a battery.
Keep children away from acid and batteries.
Fires, sparks, naked flames and smoking are prohibited.-Avoid causing sparks when dealing with cables and electrical equipment, and beware of electrostatic discharges.-Avoid short circuits.
Explosion hazard:-A highly explosive oxyhydrogen gas mixture is produced when batteries are charged.
Corrosive hazard:-Battery acid is highly corrosive, therefore:-Wear protective gloves and eye protection.-Do not tilt the battery, acid may escapefrom the vent openings.
First aid:-Rinse off acid splashed in the eyes immediately for several minutes with clear water! Then consult a doctor immediately.
-Neutralise acid splashes on the skin or clothes immediately with acid neutraliser (soda) or soap
suds, and rinse with plenty of water.-If acid is swallowed, consult a doctor immediately.
Warning notes: The battery case can become brittle, toavoid this:
-Do not store batteries in direct sunlight.-Discharged batteries may freeze up, therefore store in an area free from frost.
Disposal:-Dispose of old batteries at an authorised collection point.
-The notes listed under item 1 are to be followed for transport.-Never dispose of old batteries in household waste.
Product name: Copper Ease.Copper Ease contains no hazardous ingredients at or above regulatory disclosure limits, however,safety precautions should be taken when handling (use of oil-resistant gloves and saftey glasses arerecommended - respiratory protection is not required). Avoid direct contact with the substance andstore in a cool, well ventilated area avoiding sources of ignition, strong oxidising agents and strongacids. Dispose of as normal industial waste (be aware of the possible existance of regional or nationalregulations regarding disposal), do not discharge into drains or rivers. In case of fire: in combustion the product emits toxic fumes, extinguish with alcohol or polymer foam,carbon dioxide or dry chemical powder. Wear self-contained breathing apparatus and protective clothingto prevent contact with skin and eyes.FIRST AIDSkin contact: there may be mild irritation at the site of contact, wash immediately with plenty of soapand water.Eye contact: there may be irritation and redness, bathe the eye with running water for 15 minutes. Ingestion: there may be irritation of the throat, do not induce vomiting, wash out mouth with water.A safety data sheet for this product can be obtained by writing to the manufacturer at the following address: Comma Oil and Chemicals Ltd., Deering Way, Gravesend, Kent DA12 2qX.Tel: 01474 564311, Fax: 01474 333000.
BATTERY SAFETY INFORMATION
COPPER EASE SAFETY INFORMATION
The battery can be serviced in situ. To remove the battery, first remove the negative battery lead,followed by the positive battery lead, then the battery strap. When reinstalling the battery apply asmall smear of Vaseline to the terminals.
BATTERY REMOVAL AND MAINTENANCE
WARNING Refer to the battery safety section below.
WARNING NOTES AND SAFETY REGULATIONS FOR FILLED LEAD-ACID BATTERIES
1. Storage and transport- Batteries are filled with acid.- Always store and transport batteries upright
and prevent from tilting so that no acid can escape.
- Store in a cool and dry place.- Do not remove the protective cap from the
positive terminal.- Run a FIFO (first in-first out)warehouse
management system.
2. Initial operation- The batteries are filled with acid at a density of
1.28g/ml during the manufacturing process and are ready for use.
- Recharge in case of insufficient starting power (cf. section 4).
3. Installation in the vehicle and removal fromthe vehicle
- Switch off the engine and all electrical equipment.
- When removing, disconnect the negative terminal first.
- Avoid short circuits caused by tools, for example.- Remove any foreign body from the battery tray,
and clamp battery tightly after installation.- Clean the terminals and clamps, and lubricate
slightly with battery grease.- When installing, first connect the positive
terminal, and check the terminal clamps for tight fit.
- After having fitted the battery in the vehicle, remove the protective cap from the positive terminal, and place it on the terminal of the replaced battery in order to prevent short circuits and possible sparks.
- Use parts from the replaced battery, such as the terminal covers, elbows, vent pipe connection and terminal holders (where applicable); use available or supplied filler caps.
- Leave at least one vent open, otherwise there is a danger of explosion. This also applies when old batteries are returned.
4. Charging- Remove the battery from the vehicle;
disconnect the lead of the negative terminal first.- Ensure good ventilation.- Use suitable direct current chargers only.- Connect the positive terminal of the battery to
the positive output of the charger. Connect the negative terminal accordingly.
- Switch on the charger only after the battery hasbeenconnected, and switch off the charger first after charging has been completed.
- Charging current-recommendation: 1/10 ampere of the battery capacity Ah.
- Use a charger with a constant charging voltage of 14.4V for re-charging.
- If the acid temperature rises above 55o Celsuis, stop charging.
- The battery is fully charged when the charging voltage has stopped rising for two hours.
5. Maintenance- Keep the battery clean and dry.- Use a moist anti-static cloth only to wipe the
battery, otherwise there is a danger of explosion.
- Do not open the battery.- Recharge in case of insufficient starting power
(cf. section 4).
6. jump Starting- Use the standardised jumper cable in
compliance with DIN 72553 only, and follow theoperating instructions.
- Use batteries of the same nominal voltage only.- Switch off the engines of both vehicles.- First connect the two positive terminals (1) and
(2), then connect the negative terminal of the charged battery (3) to a metal part (4) of the vehicle requiring assistance away from the battery.
- Start the engine of the vehicle providing assistance, then start the engine of the vehicle requiring assistance for a maximum of 15 seconds.
- Disconnect the cables in reverse sequence (4-3-2-1).
7. Taking the battery out of service- Charge the battery; store in a cool place or in
the vehicle with the negative terminal disconnected.
- Check the battery state of charge at regular intervals, and correct by recharging when necessary (cf. section 4).
(1)(2)
(3) (4)
12V 12V
BATTERY SAFETY INFORMATION...cont.
PH TIMBERWOLFTW S426TDHB 18SERVICE INSTRUCTIONS
CHECK FREE ROTATION OF DRUM AND HAMMERS
TIMBERWOLFTW S426TDHB19 SERVICE INSTRUCTIONS
4
5
1. Turn off shredder and remove key.
2. Remove the negative battery lead.
3. Turn the discharge tube to point forward of the machine.
4. Using a 24 mm spanner remove the two M16 nuts clamping the drum housing shut.
5. Carefully lift the drum housing until it rests on its stop.
6. Using the paddles to turn the drum, set a bank of hammers at 12 o'clock.
7. Check that each of the 9 hammers in this bank all rotate freely through 360o.
8. Turn the drum to check the second bank of hammers.
9. Check all 9 hammers in second bank also rotate freely through 360o.
10. Lower the top of the drum housing and reinstall the two M16 nuts.
11. Torque these to 65lbft.
12. Re-attach the battery lead.
7
The TW S426TDHB / TW S426TDHBA is subject to large vibrations during the normal course ofoperation. Consequently there is always a possibility that nuts and bolts will work themselves loose.It is important that periodic checks are made to ensure the security of all fasteners. Fasteners shouldbe tightened using a torque wrench to the settings listed below . Uncalibrated torque wrenches canbe inaccurate by as much as 25%. It is therefore essential that a calibrated torque wrench isused to achieve the tightening torques listed below.
CHECK FITTINGS
WARNING Wear heavy gloves for the drumdrum/hammer checking operation.
Size Pitch Head Torque Ibft
Hammer Locating Bolts M8 Standard 6 mm Allen Key 31Anvil Bolts M16 Standard 14 mm Allen Key 175Drum Shaft Retaining Bolts M16 Standard 24 mm Hex 90Funnel Retaining Nuts M12 Standard 19 mm Hex 60General M8 Standard 13 mm Hex 17General M10 Standard 17 mm Hex 34General M12 Standard 19 mm Hex 60
PH TIMBERWOLFTW S426TDHB 20
CHANGE BLADES
WARNING Wear heavy gloves for the blade changing operation.
SERVICE INSTRUCTIONS
9
84
5
1. Turn off shredder and remove key.
2. Remove the negative battery lead.
3. Turn the discharge tube to point forward of the machine.
4. Using a 24 mm spanner remove the two M16 nuts clamping the drum housing shut.
5. Carefully lift the drum housing until it rests on its stop.
6. Using the paddles to turn the drum, set a bank of hammers at 12 o'clock.
7. With a 6mm hex key undo and remove the bolt in the hammer at each end of the bank of hammers.
8. The shaft can now be withdrawn. The shaft will need to be tapped away from the main drive pulley side.
9. As the shaft is removed the hammers will be released off the shaft. These need to be held and removed as the shaft is withdrawn.
10. The hammer replacement is the reverse of the above with the addition of some copper slip on the hammer retainer bolts. Note the hammer bushes should not be greased or lubricated in any way. Any build up of debris should be removed from both the shaft and the hammer bushes so the hammer can swing freely.
11. Turn the drum to change the second bank of hammers.
12. Lower the top of the drum housing and reinstall the two M16 nuts.
13. Torque these to 65lbft.
14. Re-attach the battery lead.
7
All the hydraulic hoses should be regularly inspected for chafing and leaks. The hydraulic system ispressurized to 150 Bar (2175 PSI) and thus the equipment containing it must be kept in good condition.Identify the hoses that run to the top motor. These have the highest chance of damage as they areconstantly moving. If any hydraulic components are changed new seals should be installed duringreassembly. Fittings should then be retightened.
CHECK HOSES
21
TENSION DRIVE BELTS
SERVICE INSTRUCTIONSGREASE THE DRUM BEARINGS
TIMBERWOLFTW S426TDHB
2 1. Remove the drum housing guard, situated on the offside of the machine.
2. Apply two pumps of grease to the bearing taking care not to over grease.
3. Refit guard.
2
34
1. Remove the drum housing guards, (as shown in diagram above).
2. Slacken the six M12 bolts but do not remove (there are three located on each side of the machine).
3. Slacken the M8 tension nut from the adjuster bracket about 5mm on both sides of roller box.
4. Tension each of the M8 adjuster nuts drawing the drum housing, roller box and funnel away from the engine bay. For instructions on checking belt tension & correct belt tension values, please refer to the Timberwolf V-Belt Tensioning Data (page 31).
5. Check the belt tension and repeat as necessary.6. Once belt tension is correct lock off the M8 nut against the
tension bracket.7. Retighten the six M12 bolts.8. Refit the belt guard when finished.
Both bearings need regularly greasing.
1. Turn the discharge tube to point forward of the machine.2. Using a 24 mm spanner remove the two M16 nuts clamping the
drum housing shut.3. Carefully lift the drum housing until it rests on its stop.4. Apply two pumps of grease to the bearing taking care not to
over grease.5. Lower the top of the drum housing and reinstall the two M16
nuts.6. Torque these to 65lbft.
NOTE: There will normally be a rapid drop in tension during run-in period for new belts. When newbelts are fitted, check the tension every 2 - 3 hours and adjust until the tension remains constant.
Belt failures due to lack of correct tensioning will not be covered under your Timberwolf warranty.
3
2
PH TIMBERWOLFTW S426TDHB 22SERVICE INSTRUCTIONS
NOTE: This should be done every 50 hours. In dirty or dusty conditions or during periods of hardwork it should be done more frequently. If the slides become dry the top roller will tend to hangup and the pulling-in power of the roller will be much reduced. Excessive wear will ensue.
2
The jack stand requires intermittent greasing to maintain a smooth operation.1. Brush off dirt with a stiff brush.2. Apply grease liberally to screw thread using a brush.3. Wind mechanism up and down a couple of times to ensure grease has covered all surfaces.
1. Remove the top roller box guard.2. Remove the nearside roller box guard.3. Apply multipurpose grease directly to the slide
surfaces indicated. DO NOT USE GRAPHITE BASED GREASE.
4. Refit both the roller box guards.
1. Remove the top roller box guard.2. Locate the grease nipple indicated.3. Use a pump action grease gun to apply a generous
amount of grease to each roller drive. DO NOT USE GRAPHITE BASED GREASE.
4. Refit the top roller box guard.
1. Remove the discharge tube.
2. Apply multipurpose grease to surface shown.
3. Refit discharge tube.
2
NOTE: This should be done regularly. In dirty and dusty conditions or during periods of hardwork it should be weekly. If the bearings and splines are allowed to run dry premature wear willoccur resulting in a breakdown and the need for replacement parts. This failure is not warranty.Early signs of insufficient grease includes squeaking or knocking rollers.
2
GREASE THE ROLLER SPLINE AND BEARING
GREASE THE ROLLER BOX SLIDES
GREASE THE JACK STAND
GREASE THE DISCHARGE FLANGE
ENGINE SERVICINGAll engine servicing must be performed in accordance with the Engine Manufacturer’s Handbookprovided with the machine. FAILURE TO ADHERE TO THIS MAY INVALIDATE WARRANTY AND/ORSHORTEN ENGINE LIFE.
TIMBERWOLFTW S426TDHB23 WARRANTY STATEMENT
ENTEC INDUSTRIES LTD 36 MONTHWARRANTYWARRANTYThe warranty period for your Entec Industries Ltd machine commences on the date of sale to the firstend user and continues for a period of 36 months. This guarantee is to the first end user only and is nottransferable except when an Authorised Timberwolf Dealer has a machine registered with EntecIndustries Ltd as a hire chipper or long term demonstrator – in these situations they are duly authorisedto transfer any remaining warranty period to their first end user. Any warranty offered by the TimberwolfDealer beyond the original 36-month period will be wholly covered by said Dealer.
LIABILITYNo liability will be accepted for special, indirect, incidental, or consequential loss or damages of any kind.Our obligation under this warranty is limited to repair at Entec Industries Ltd Authorised TimberwolfDealers or at Entec Industries Ltd premises.
WARRANTY STATEMENTEntec Industries Ltd warrants to the first end user that:
Your machine shall be designed, built and equipped, at the point of sale, to meet all current•applicable regulations.Your machine shall be free from manufacturing defects both in materials and workmanship in•normal service for the period mentioned above.
Normal wear & tear on consumable items and their routine maintenance or replacement are notwarrantable items. Engine units are covered independently by their respective manufacturer warranties.OWNERS WARRANTY RESPONSIBILITIESAs the owner of an Entec Industries Ltd machine you are responsible for the following:
Operation of the machine in accordance with the Entec Industries Ltd instruction manual.•Performance of the required maintenance listed in your Entec Industries Ltd instruction manual.•In the event of a failure the Entec Industries Ltd authorised Timberwolf dealer is to be notified•within 10 days of failure and the equipment is to be made available for inspection by the dealertechnician.
WARRANTY RESTRICTIONSThe Entec Industries Ltd warranty is restricted to the first end user only and is not transferable exceptwhen an authorised Timberwolf dealer has a wood chipper registered with Entec Industries Ltd as a hirechipper or long term demonstrator – in these situations they are duly authorised to transfer any remainingwarranty period to their first end user.The Entec Industries Ltd warranty may be invalidated if any of the following apply:
The failed parts or assembly is interfered with in any way.•Normal maintenance has not been performed.•Incorrect reassembly of components.•The machine has undergone modifications not approved in writing by Entec Industries Ltd.•In the case of tractor driven equipment, use has been on an unapproved tractor.•Conditions of use can be deemed abnormal.•The machine has been used to perform tasks contrary to those stated in the Entec Industries Ltd•instruction manual.
WARRANTY SERVICETo obtain warranty service please contact your nearest Entec Industries Ltd approved Timberwolf dealer.To obtain details of the nearest facility please contact Entec Industries Ltd at the address on the back ofthis manual. These warranty terms are in addition to and not in substitution for and do not affect any rightand remedies which an owner might have under statute or at common law against the seller of the goodsunder the contract by which the owner acquired the goods.
PH TIMBERWOLFTW S426TDHB
CERTIFICATE OF CONFORMITY
24
TIMBERWOLFTW S426TDHB25
EXAMPLE
IDENTIFICATION PLATE
PH TIMBERWOLFTW S426TDHB 26DECALS
Hot exhaustDanger.
Rotating blades.Keep hands and feet out.
High velocity discharge -keep clear
Reverse feed
Forward feed
Read the instruction manual for greasing and maintenance information
Personal Protective Equipment required
The instruction manualwith this machine contains important
operating, maintenanceand health and safety information. Failure to follow the information
contained in the instruction manual maylead to death or serious
injury.
Lifting eye is designed to lift themachine’s weight only.
Do not use hoist hook directly onlifting eye. Use correctly rated
safety shackle only through liftingeye.Lifting eye to be inspectedevery 6 months or before each
use. Always visually inspect liftingeye prior to each use. Do not
use lifting eye if damaged.
New drive belts need re-tensioning.
When new belts are fittedcheck tension every 2-3
hours & adjust until tension remains constant.
Push to stop.
Do not pull here.
If excessive vibration isnoted whilst using this
shredder switch off immediately,
check for free rotation ofrotor drum & hammers.
Refer to instruction manual
Allow time for allshredded material to be
ejected from the dischargebefore switching off.
Decal Description Decal Description
616
617
1661
1662
18393
18713
4099
2800 2801
670
2949
18714
1399
P691
TIMBERWOLFTW S426TDHB27 DECALS
Danger. Do not operate without this
cover in place.
Danger. Rotating blades inside.
Stop engine and remove keybefore removing discharge unit.
Warning. Do not engage startermotor for more than 20 seconds.
Allow one minute beforeattempting to start. Investigate
reasons for failure to start.Excessive cranking will result in
starter motor failure. This will notbe covered under warranty.
Caution. When transporting,discharge clamps may work
loose.Check frequently.
Caution. Avoid standing
directly in front of feed funnelto reduce exposure to noise,
dust and risk fromejected particles.
Danger. Do not use this
machine without the discharge unit fitted. Failure
to comply may result in serious inury or damage.
WarningFailure to maintain brake adjustment will result in
damper failure. No warrantyliability will be accepted on
this item.
Danger.Autofeed system fitted.
Rollers may turn without warning!
When the engine is switchedoff the rollers will turn during
the run down period
Engine safetyForward latch
Fuel Here.Risk of fire. Allow engine
to cool for 1 minute beforerefuelling.
Use diesel fuel only.
P637
19517
P655
P653
P654
P656
Decal Description Decal Description
3004 2998 2950 2951 1363 17861 17862
18483 P*151
dB
LWA
11992 dB
LAeq0
12
TIMBERWOLFTW S426TDHB
1258 P650
P1810
P1811C192-0112
PH TIMBERWOLFTW S426TDHB 28ELECTRICAL PARTS LOCATOR
Date Last Modified: 13th Feb 08
TIMBERWOLFTW S426TDHB29 CIRCUIT DIAGRAM
DO
CU
ME
NT
No.
ISS
UE
CIR
CU
IT D
IAG
RA
M F
OR
: 42
6SH
142
6 S
HR
ED
DE
R-C
D
1950
30
KE
Y S
WIT
CH
AC
C
OF
F
AC
RU
N
ST
AR
T
FD ECBA
SP
LIT
TO
FU
NN
EL
LO
OM
HO
UR
FU
EL
F
UE
L
SO
LE
NO
ID
RO
TO
R
SW
ITC
H
1-A
C3m
m
411m
m12
.5m
m
pt
1mm
40 151m
m
1.5m
m16
WA
TE
R T
EM
PS
WIT
CH
OIL
PR
ES
SS
WIT
CH
LE
D
HE
AT
ER
SO
N L
ED
LE
DL
ED
PO
WE
R O
N
FUS
E 1 IG
P
1mm
2mm
155
14B
LU
ES
P#4
0.5
SO
LE
NO
IDF
WD
RE
VE
RS
E
SO
LE
NO
ID
EN
GIN
E
GR
OU
ND
PO
INT
.5m
m14
.5m
m8
1mm
40
1mm
3mm
2748182m
m
1mm
20
GL
OW
PL
UG
LA
MP
OU
T 3
BA
T
OU
T 5
OU
T 1
OU
T 2
15 16 17 18141312
FU
EL
HO
LD
SO
LE
NO
ID
BA
T 1
2 V
IGP
SO
L G
ND
SP
EE
D C
ON
TR
OL
LE
D
EM
ER
GE
NC
Y/R
OT
OR
SW
ITC
H
RE
SE
T R
EV
ER
T T
O R
ES
ET
MO
DE
ST
T
RS
T
AX
1
AX
2
GN
D
EP
C
8 9 10 1175 6
GN
D 0
v
GL
OW
PL
UG
I/P
IN-
EP
A
IN+
EP
B
1 32 4
SP
EE
D S
IG -
SP
EE
D S
IG +
OIL
PR
ES
SU
RE
SW
WA
TE
R T
EM
P S
W
CO
NT
RO
LL
ER
H-B
OX
PC
U
LIN
K L
EA
D
8530
86
8787a
ST
AR
T
RE
LA
Y
LA
TC
H R
EL
AY
FW
D S
OL
GR
OU
ND
SE
CU
RIT
Y
EN
GIN
E
401m
m
391m
m
401m
m
80.
5
50E
1mm
40401m
m
1mm
R
1mm
33
71m
m28
1mm
PU
MP
ME
TE
R
FR
OM
SA
FE
TY
SW
ITC
H
CO
NF
IGU
RA
TIO
N T
.B.A
.
23
12
31
8530
87a 8687
B
BLA
CK
N
BR
OW
NU
B
LUE
S
GR
EY
G
GR
EE
N
LG
LIG
HT
GR
EE
NO
O
RA
NG
EK
P
INK
R
RE
D
W
WH
ITE
Y
YE
LLO
W
KE
Y T
O W
IRIN
G
P
PU
RP
LE
B/W
B
LAC
K W
ITH
WH
ITE
TR
AC
ER
GR
EE
NS
P#2
BL
AC
KS
P#1
U
W/P
W
HIT
E W
ITH
PU
RP
LE T
RA
CE
RB
P/W
P
UR
PLE
WIT
H W
HIT
E T
RA
CE
R
N/B
P
B/N
B/N
U/B
B
LUE
WIT
H B
LAC
K T
RA
CE
R
W
O
B
BU
WUO
P/W
G/U
U
P/WP/W
U/G
B
W/P
BR
BR
G
R
R
Y/U
Y
ELL
OW
WIT
H B
LUE
TR
AC
ER
N/B
B
RO
WN
WIT
H B
LAC
K T
RA
CE
R
W/R
B
U
BB
/W
P
N/R
B/N
O
U
B
N/R
B
RO
WN
WIT
H R
ED
TRA
CE
R
Y/UY/R
N
B
W/R
B
B/R
W/P
W/P
W/P
U/B
U/G
B
LUE
WIT
H G
RE
EN
TR
AC
ER
G/U
G
RE
EN
WIT
H B
LUE
TR
AC
ER
B/R
U/B
351m
m
SP 2
SP 2
SP 1
SP 1
SP 1
SP 1
SP 1
SP 1
SP 1
SP 1 SP 1
SP 1
SP 5
SP 4
SP 4
SP 4
SP 4
SP 4
GL
OW
PL
UG
S
PU
LL
HO
LD
21
AL
TE
RN
AT
OR
RO
TO
R
O/P
ST
AR
TE
R
BA
TT
ER
Y
ST
AR
TE
RS
OL
TE
RM
EN
G G
ND
PO
INT
BA
TT
25m
m
BA
TT
25m
m RR
U
R
MA
IN T
ER
M
ST
AR
TE
RM
OT
OR
SP 4
B
G
N.O
./N.C
.
1314
2122
B/W
Y/U Y/R
MA
IN L
OO
M 1
8461
PA
RT
No
. 173
78
PA
RT
No
. 173
77
PA
RT
No
. 178
09
M
U SP 4
SP 1B
B
1 2 3
SA
FE
TY
SW
N.O
./N.C
.
P/W
G/B
U
G/B
G/U
RE
VF
WD
N.O
./N.C
.
1314
2122
N.O
.
1314
CD
AB
RE
VF
WD
N.O
./N.C
.
1314
2122
N.O
.
1314
FU
NN
EL
RO
LLE
R C
ON
TR
OL
RE
D B
AR
8530
86
8787a
SP 4
N
FU
NN
EL
RO
LLE
R C
ON
TR
OL
AX
2
AX
1
OU
T 4
AU
TO
RE
VE
RS
E P
UL
SE
OU
TP
UT
E-S
TO
P
SW
ITC
H
N.O
./N.C
.
1314
2122
TR
AC
K M
AC
HIN
E O
NL
Y
B/W
B/W
N N/B P
N/R
W
U
P
P/W
B/N
B
LAC
K W
ITH
BR
OW
N T
RA
CE
R
Date Last Modified: 15th Feb 08
PH TIMBERWOLFTW S426TDHB 30HYDRAULIC LAYOUT
PUMP
TANK
1781417815
17813
18525
17812
FILTER
MOTOR
Date Last Modified: 12th Sept 06
KIT NO: 17826
DCVP T
A B
13/75G 190TDHB 190TFTR 190TVGTR 350DHB(t) PTO100 PTO150S426
ShredderS426 TFTR Shredder
PTOS426 Shredder
Gates Super HC-
MN
Gates Super HC-MN
Gates Super HC-MN
Gates Super HC-MN
Gates Super HC-MN
Gates Super HC-MN
Gates Super HC-MN
Gates Super HC-MN
Gates Super HC-MN
Gates Super HC-MN
SPA SPA SPA SPA SPB SPA SPA SPB SPB SPB900 1232 1232 1232 2530 900 900 2120 2120 1700
Belt Deflection = h 2 3 3 3 8 2 2 7 7 63.26 - 3.50 5.69 - 6.1 5.68 - 6.08 5.54 - 5.94 8.32 - 8.91 4.36 - 4.69 4.36 - 4.67 7.95 - 8.52 7.96 - 8.53 6.50 - 6.902.80 - 3.03 4.88 - 5.28 4.87 - 5.28 4.75 - 5.14 7.13 - 7.72 3.74 - 4.04 3.74 - 4.04 6.81 - 7.38 6.82 - 7.39 5.60 - 6.00
TW Model No.:
Roto
r Bel
ts
Belt Mffr / Type
Belt Pitch DesignationBelt Length in mm
Force Reading New beltUsed Belt
METHOD:1. Set the deflection distance on the lower scale of the tension gauge so that the underside of the 'o'-ring
equals the 'h' value given in the table.2. Ensure that the deflection force scale is zero'd by pushing the upper 'o'-ring all the way down.3. Place the tension gauge in the centre of the belt span as shown in the diagram.4. Press downwards on the rubber buffer, deflecting the belt until the underside of the lower 'o'-ring is level
with the belt behind (use a straight edge if there is only 1 belt).5. Take the reading from the deflection scale of the tension meter (read at the lower edge of the 'o'-ring) &
compare this value with that given in the table.6. Tighten or loosen belts as required following procedure given in this operator's manual.
Tension gauges are available from Timberwolf spares, quoting part no. 18091
Rotor Pulley
Engine Pulley
TIPS ON BELT TIGHTENING:There will normally be a rapid drop in tension•during the run-in period for new belts. When newbelts are fitted, check the tension every 2-3 hours& adjust until the tension remains constant.The best tension for V-belt drives is the lowest•tension at which the belts do not slip or ratchetunder the highest load condition.
Too much tension shortens belt & bearing life.•Too little tension will affect the performance of•your machine especially in respect of no-stressdevices.Ensure that belt drives are kept free of any•foreign materials.If a belt slips - tighten it! •
TIMBERWOLFTW S426TDHB31 V-BELT TENSIONING TABLE
PH TIMBERWOLFTW S426TDHB 32
The following illustrations are for parts identification only. The removal orfitting of these parts may cause a hazard and should only be carried out bytrained personnel.
PARTS LISTS
CHASSIS - WITH FIXED TOWHEAD 33CHASSIS - WITH ADjUSTABLE TOWHEAD 34CHASSIS - RAINFLAPS AND REFLECTORS 35CONTROL BOX 36CONTROL PANEL 37DECALS SEE PAGES 26 - 27DISCHARGE 38DRIVE TRAIN 39DRUM 40DRUM HOUSING 41ELECTRICAL LAYOUT 42ENGINE 43ENGINE BAY 44FUEL TANK/GUARDS 45FUNNEL 46HYDRAULICS 47ROLLER BOX 48
TIMBERWOLFTW S426TDHB33 CHASSIS (1)
1 2 3 4 5 1
78
910
711
12
13
1415
1646
1542
1917
426
4048
40 22 32
39
23
2425
2126
37 38
20
2731
47
29
34 3128
30 26 35
3222
33
x2
x8x4
Item
Part
No
Part
Nam
eq
’ty1
1036
M10
Pla
in N
ut2
217
981
Bra
ke R
od1
304
81M
8 T
Nyl
oc N
ut9
400
78N
ut B
all
25
0079
FN
ut B
all
16
1905
8FB
Out
er C
hass
is B
eam
N/S
17
0067
Pop
Riv
et4
829
63C
atch
19
0360
M10
/25
Bol
t8
1008
39M
10 C
Was
her
811
0358
Cat
ch P
late
112
1785
7FB
Tool
Box
Lid
113
1785
6FB
Nea
rsid
e M
udgu
ard
114
0352
M8/
40 B
olt
215
0712
M8
C W
ashe
r16
1619
619
Ligh
tboa
rd1
1718
121
M8/
120
Bol
t2
Item
Part
No
Part
Nam
eq
’ty18
1907
1FB
Mud
guar
d Su
ppor
t N/S
119
1905
7FB
Ligh
tboa
rd B
rack
et1
2019
059F
BO
uter
Cha
ssis
Bea
m O
/S1
2103
21M
12/3
0 B
olt
822
0704
M12
C W
ashe
r12
2318
352F
BD
rum
Hou
sing
Cro
ss B
eam
124
1754
7FB
Rea
r Cro
ss B
eam
125
1754
8FB
Fron
t Cro
ss B
eam
126
0702
M12
A W
ashe
r12
2730
43FS
Out
er B
eam
Han
dle
228
P*14
00jo
ckey
Whe
el C
lam
p1
2918
333
jock
ey W
heel
130
1520
M10
/50
Bol
t2
3107
01M
10 A
Was
her
832
0644
M12
P N
yloc
Nut
833
1749
3To
w H
ead
134
4345
M10
P N
yloc
Nut
6
Item
Part
No
Part
Nam
eq
’ty35
0313
M12
/100
Bol
t4
3626
33W
ind
Dow
n ja
ck S
tand
137
1785
5FB
Offs
ide
Mud
guar
d1
3819
32W
heel
(inc
. spa
re)
339
1779
2A
xle
140
0429
M12
/35
Bol
t6
4103
50M
8/25
Bol
t4
4204
79M
8 P
Nyl
oc N
ut2
4316
83Pl
ain
Stan
d O
ff1
4403
54M
8/60
Bol
t1
4516
82Th
read
ed S
tand
Off
146
0346
M8/
20 B
olt
547
0382
M10
/30
Bol
t4
4804
15H
eavy
Was
her
249
1907
2FB
Mud
guar
d Su
ppor
t O/S
150
P*14
02Pr
essu
re P
ad1
51P*
1399
Cla
mp
Han
dle
1
44 43 315
46 1545 36
1541 42
3431x2
15
49
153
1815
42x2
on
opp.
sid
e
x2 o
nop
p. s
ide
3
46
41
50
51
PH TIMBERWOLFTW S426TDHB 34CHASSIS (2)
1 2 3 4 5 1
78
910
711
12
13
1415
1646
1542
1917
42
640
48
40 22 32
39
23
2425
2126
37 38
20
2731
47
2934 31
28
30
26
35
32
4833
x2
x8
x4
Item
Part
No
Part
Nam
eq
’ty1
1036
M10
Pla
in N
ut2
219
584
Bra
ke R
od1
304
81M
8 T
Nyl
oc N
ut9
400
78N
ut B
all
25
0079
FN
ut B
all
16
1955
1FB
Out
er C
hass
is B
eam
N/S
17
0067
Pop
Riv
et4
829
63C
atch
19
0360
M10
/25
Bol
t8
1008
39M
10 C
Was
her
811
0358
Cat
ch P
late
112
1785
7FB
Tool
Box
Lid
113
1785
6FB
Nea
rsid
e M
udgu
ard
114
0352
M8/
40 B
olt
215
0712
M8
C W
ashe
r16
1619
619
Ligh
tboa
rd1
1718
121
M8/
120
Bol
t2
Item
Part
No
Part
Nam
eq
’ty18
1907
1FB
Mud
guar
d Su
ppor
t N/S
119
1905
7FB
Ligh
tboa
rd B
rack
et1
2019
552F
BO
uter
Cha
ssis
Bea
m O
/S1
2103
21M
12/3
0 B
olt
822
0704
M12
C W
ashe
r8
2318
352F
BD
rum
Hou
sing
Cro
ss B
eam
124
1754
7FB
Rea
r Cro
ss B
eam
125
1754
8FB
Fron
t Cro
ss B
eam
126
0702
M12
A W
ashe
r12
2730
43FS
Out
er B
eam
Han
dle
228
P*14
00jo
ckey
Whe
el C
lam
p1
2918
333
jock
ey W
heel
130
1520
M10
/45
Bol
t2
3107
01M
10 A
Was
her
832
0644
M12
P N
yloc
Nut
833
1958
3A
djus
tabl
e To
w H
ead
134
4345
M10
P N
yloc
Nut
6
Item
Part
No
Part
Nam
eq
’ty35
4333
M12
/170
Bol
t4
3626
33W
ind
Dow
n ja
ck S
tand
137
1785
5FB
Offs
ide
Mud
guar
d1
3819
661
Whe
el (i
nc. s
pare
)3
3917
792
Axl
e1
4004
29M
12/3
5 B
olt
6 41
0350
M8/
25 B
olt
442
0479
M8
P N
yloc
Nut
243
1683
Plai
n St
and
Off
144
0354
M8/
60 B
olt
145
1682
Thre
aded
Sta
nd O
ff1
4603
46M
8/20
Bol
t5
4703
82M
10/3
0 B
olt
448
0415
Hea
vy W
ashe
r6
4919
072F
BM
udgu
ard
Supp
ort O
/S1
50P*
1402
Pres
sure
Pad
1 51
P*13
99C
lam
p H
andl
e1
44 43 315
46 1545 36
1541 42
3431
x2
15
49
153
1815
42x2
on
opp.
side
x2 o
nop
p. s
ide
3
46
41
5051
TIMBERWOLFTW S426TDHB35 CHASSIS - RAIN FLAPS & REFLECTORS
Item Part No Part Name q’ty1 18919 Reflector Support Bracket 22 18923 Reflector Amber 13 0346 M8/20 Bolt 44 0711 M8 A Washer 45 0236 M5 P Nyloc Nut 46 0857 M5 A Washer 47 0712 M8 C Washer 12
Item Part No Part Name q’ty8 0481 M8 T Nyloc Nut 89 18922 Reflector Clear 210 0856 M5/20 Pan Pozi 411 0351 M8/30 Bolt 412 19626 Rainflap Clamp 213 19625 Rainflap Supports 214 19603 Rainflap 2
Date Last Modified: 5th April 12
11712
1413
78
1093
45
6
2
10
7
8
5
1
PH TIMBERWOLFTW S426TDHB 36CONTROL BOX
Item Part No Part Name q’ty1 17802FB Control Box Cover 12 17963 M10/160 Bolt 13 0839 M10 C Washer 24 2804 Bush M10 Top Hat 45 0067 Pop Rivet M5/12 46 18108 M6/8 Pan Pozi 47 2834 AV Mount VE Type 28 4345 M10 P Nyloc Nut 1
Item Part No Part Name q’ty9 17803FS Finger Plate 210 18168 M4/35 Pan Pozi 411 18100 M4 Washer 412 18235 M4 P Nyloc Nut 413 17927 Limit Switch 214 17805FS Switch Mounting Plate 115 0142 M6 P Nyloc Nut 416 18000 AV Mount 3
Date Last Modified: 31st March 11
x4
1
23 4
9
4
7
4 38
10
11
13
14
12
6 x4
5
11
12
1516
TIMBERWOLFTW S426TDHB37 CONTROL PANEL
Date Last Modified: 5th May 11
13
01 2
17
Item Part No Part Name q’ty1 0438 M6/16 Pan Pozi 32 0709 M6 C Washer 33 Supp’d with loom Relay 34 0391 M6 T Nyloc Nut 35 Supp’d with loom Fuse 16 1151 Countersunk Pop Rivet 17 18104 M5/12 Pan Pozi 48 0857 M5 A Washer 9 9 18405 H-Box 1
Item Part No Part Name q’ty10 2958FS Electrical Panel 111 18291 M5 Plain Nut 512 3024 M5 Spring Washer 513 4033 M5 AV Mount 514 Supp’d with loom LED 215 Supp’d with engine Ignition Switch 116 0327 Hours Counter 117 2951 Control Panel Decal 118 18398F H-Box Bracket 2
24
5
7
18
6
9
10
1112
813
14
15
16
1
3
24
8
PH TIMBERWOLFTW S426TDHB 38DISCHARGE
Item Part No Part Name q’ty1 18427FO Discharge Tube 12 18663FO Discharge Bucket 13 0644 M12 P Nyloc Nut 24 0704 M12 C Washer 25 0429 M12/35 Bolt 36 17996 Black Handle Grip 27 0364 Catch 28 0067 M5 Pop Rivet 8mm long 89 4088 Catch Plate 210 0045 M12 T Nyloc Nut 111 0702 M12 A Washer 212 18382 M12/280 Bolt 113 18351FO Anti Block Flap 114 2837MS Clamp Nut Small 115 1511 M16 P Nyloc Nut 116 0832 M24 Washer 117 0333 M16/60 Hex Bolt 118 1649MS Discharge Clamp Handle 219 4109M M16 Clamp Nut 220 4131 Roll Pin 221 0434 M16/70 Hex Bolt 122 1354 M16 C Washer 123 18643 Discharge Grill Washer 124 18671 Bush Top Hat 125 18664FS Stay Arm 126 18710MS Stay Handle 127 0360 M10/25 Bolt 128 0701 M10 A Washer 129 0839 M10 C Washer 1
1
21
4
2
Date Last Modified: 16th Dec 10
19
16 14
18
43
20
1722
15
7
5
5
89
1011
12 136
23
18
19
20
5 4
2410
2625
2927
TIMBERWOLFTW S426TDHB39 DRIVE TRAIN
Date Last Modified: 15th Aug 07
1
3 4
5
Item Part No Part Name q’ty1 18068 Vee Belt 2120 SPB 32 17921 Taper Lock Bush 3020 50 mm 13 18067 Pulley 280 x 3 14 18328 Key 37 x 14 x 9 15 18029 Pulley Engine 168 x 3 SPB 1
2
PH 40TIMBERWOLFTW S426TDHBDRUM
Item Part No Part Name q’ty1 18381 M16/45 Bolt 82 1218 M16 Hardened Washer 83 17793 Bearings 24 18350PS Bearing Shield 15 18141F Drum 16 17616 Hammer Shaft 2
Item Part No Part Name q’ty7 18072MH Hammer Plain - Forging 148 18073MH Hammer with Cross Drill - Forging 49 18354 Hammer Bush 40 x 40 1410 P0000022 M8/80 Caphead 411 18355M Hammer Bush 40 x 40 Cross for Drill 4
Date Last Modified: 11th June 12
1
7 inner hammers per shaft2 outer hammers per shaft
This section x2
2
3
5
4
3
218
10
7
6
118
9
TIMBERWOLFTW S426TDHB41 DRUMHOUSING
Item Part No Part Name q’ty1 18425FO Top Section Drum Housing 12 18485 Catcher Finger 33 18484 M12/30 Button Head 24 0045 M12 T Nyloc Nut 35 0644 M12 P Nyloc Nut 86 0479 M8 P Nyloc Nut 17 0712 M8 C Washer 78 2978S M16 Flange Nuts 29 1721 M8/10 Bolt 210 0711 M8 A Washer 411 0355 M8/16 Csk 412 18149FO Lower Fan Housing 113 0178 Rubber End Stop 114 18168 M4/35 Pan Pozi 215 1348 Limit Switch 116 1868 M8 AV Mount 217 18153PS Switch Mounting Plate 118 1321 M12/30 Bolt 419 0704 M12 C Washer 18
Item Part No Part Name q’ty20 18330MS Side Brace 121 0429 M12/35 Bolt 222 0431 M12/40 Bolt 623 0702 M12 A Washer 224 18331PS Catcher Plate 225 4068 M10/40 Caphead 1026 0701 M10 A Washer 2027 0052 M10 T Nyloc Nut 1028 0350 M8/25 Bolt 429 18143FS Fan Assembly 130 18144M Fan Hub 131 2850 Taper Lock 2012 50 132 18329 Key 22 x 14 x 9 133 18150FO Fan Cover 134 18381 M16/45 Bolt 235 0277 M12/25 Bolt 236 0350 M8/25 Bolt 437 18167FO Base Section Drum Housing 138 P*12 M8/10 Csk Screw 2
Date Last Modified: 19th Nov 2014
1
6 7 8
14151617
7
9
3811 12
29
2810
3031
3233
34
18 19
20
2119
2219
5
x3 bothsides
x4
2526 27 24
13
36
735
23
235
37
23
4
5
PH TIMBERWOLFTW S426TDHB 42ELECTRICAL LAYOUT
Item Part No Part Name q’ty
1 17809 Control Box/Safety Switch Loom 1
2 18461 Main Loom 1
Item Part No Part Name q’ty
3 17378 Negative Battery Cable 1
4 17377 Positive Battery Cable 1
2
1
4
Date Last Modified: 13th Feb 08
3
TIMBERWOLFTW S426TDHB43 ENGINE PARTS
Date Last Modified: 19th Dec 13
Item Part No Part Name q’ty1 Air Cleaner 12 0095 Oil Filter 13 18345 Air Filter 14 19369 Directional Control Valve (DCV) 15 19156FB Engine Bracket Nearside 16 0711 M8 A Washer 57 0346 M8/20 Bolt 38 19155FB Engine Bracket Offside 19 4319 Radiator Kit 110 4313 Engine 111 0644 M12 P Nyloc Nut 412 4054 M10/35 Fine Thread Socket Cap 613 1629 M10/25 Fine Thread Socket Cap 1614 18338FS Engine Bracket Base 2
Item Part No Part Name q’ty15 2954 Throttle Cable Bracket 116 18029 Pulley Engine 168 x 3 SPB 117 0352 M8/40 Bolt 118 0481 M8 T Nyloc Nut 119 2946 Throttle Assembly 120 17794FB Air Intake Tube 121 4335 Radiator Fan Guard 122 0392 M6 Plain Nut 423 0437 M6/16 Bolt 424 0709 M6 C Washer 825 18106 M6 Spring Washer 426 0332 M12/90 Bolt 427 18332 AV Mount 428 0704 M12 C Washer 8
3
4
19
13
9
10
16
67
5
2
12
10
15
176
19
7
18
8
1
21
20
2324
2522
x4
11 27
28 26
x4
14
14
PH TIMBERWOLFTW S426TDHB 44ENGINE BAY
x3
12 13 14456
75
8
910
1115
13 40
21
20
22
23
24
26 1716
x5
x6
2627
25
2830
27 29
3132
18
35
33
34
Date Last Modified: 3rd April 08
x5
36
3738
2726
27
x3
39
40
Item Part No Part Name q’ty1 18477FB Exhaust Deflector 12 18478 Exhaust Clamp 13 18423 Exhaust Tube 14 0438 M6/16 Pan Pozi 35 0067 Pop Rivet 4.8 x 12 46 0235 Catch 17 17544FO Access Panel 18 4088 Catch Plate 19 2946 Throttle Assembly 110 0435 M5/16 Pan Posi 311 0857 M5 A Washers 312 0344 M8/16 Bolt 213 0711 M8 A Washer 714 4320 Reserve Tank 115 18334FO Top Engine Guard 116 4345 M10 P Nyloc Nut 517 0701 M10 A Washer 518 0709 M6 C Washer 519 0142 M6 P Nyloc Nut 320 18476 Exhaust & Fittings 121 17539 Side Guard with Filter 122 0431 M12/40 Bolt 623 0704 M12 C Washer 1224 0644 M12 P Nyloc Nut 625 17738FS Top Belt Guide 1
Item Part No Part Name q’ty26 0878 M10/20 Bolt 827 0839 M10 C Washer 1228 17737FS Bottom Belt Guide 129 0052 M10 T Nyloc Nut 230 17820FS Light Board Cable Bracket 131 4315 In-Line Fuel Filter 132 0437 M6/16 Bolt 233 4314 Fuel Pump 134 18326FB Base Guard 135 17538FO Side Guard 136 17991 Side Panel Handle 237 17776FS Battery Strap 138 4210 Battery 139 0712 M8 C Washer 1040 0479 M8 P Nyloc Nut 741 1009 M8/25 Button Head 442 18012FB Mesh for Side Guard 143 0085 Fuel Filter 144 18456 Flexi Adaptor 145 0351 M8/30 Bolt 446 0714 M8 Penny Washer 447 0481 M8 T Nyloc Nut 448 0346 M8/20 Bolt 449 1008 M8 Spring Washer 450 0476 M8 Plain Nut 4
x4
4139
42
43
44
x3
18
19
x4
x420
45
5044
1349
1
2
3
48
39
46
47
x4
TIMBERWOLFTW S426TDHB45 FUEL TANK/GUARDS
Date Last Modified: 19th Dec 2013
2
9
3
Item Part No Part Name q’ty1 1374 Locking Tank Cap 12 1658 M6/12 Bolt 63 0709 M6 C Washer 64 2617FS Fuel Tank Filler Assy 15 17537FO Fuel Tank 16 0878 M10/20 Bolt 67 0839 M10 C Washer 138 18310FO Roller Box Lid 19 0360 M10/25 Bolt 1110 18309FO Offside Roller Box Guard 111 1629 M10/25 Caphead 4
Item Part No Part Name q’ty12 18311FO Offside Drum Housing Guard 113 4059 Banjo Bolt 214 2896 Copper Washer 415 17998 Banjo Fitting 216 17933 Clear Tubing 117 0211 3/8” Drain Plug 118 0396 3/8” Dowty Washer 119 0701 M10 A Washer 1220 4345 M10 P Nyloc Nut 121 18577 Bracket 122 17892 AV Mount 50 x 21 1
1
4
5
7
6
7
8
10
1211
1314
15
16
9
67
67
79
17
18
1920 7
2122
PH TIMBERWOLFTW S426TDHB 46FUNNEL
1
11
14
26
1516
19
29
20
12
18
33
31
24 27
23
25
9
2240
10
17
7
32
28
31
tItem Part No Part Name q’ty1 18321FO Funnel 1 2 1933FS Spare Wheel Bracket 13 0045 M12 T Nyloc Nut 64 0702 M12 A Washer 45 0320 M12/25 Cup Square 46 1932 Spare Wheel 17 0704 M12 C Washer 78 18381 M16/45 Bolt 49 18108 M6/8 Pan Pozi 810 1143 M16 A Washer 811 1601 Nylon Piston 212 1603 Die Spring 213 0644 M12 P Nyloc Nut 314 0429 M12/35 Bolt 215 1605M Stainless Spacer 216 1599 Bearing Washer 217 (see page 36) Control Box 218 1348 Limit Switch 119 1520 M10/45 Bolt 220 1591 Nylon Spacer 221 4206 Nylon Bush 122 0479 M8 P Nyloc Nut 123 2923FS Hinge Pin 224 2986 1/2” Spring Bolt 2
Item Part No Part Name q’ty25 1276 Split Pin 226 1598FR Safety Bar 127 0391 M6 T Nyloc Nut 828 4344 M10 C Repair Washer 229 0178 Rubber End Stop 130 2727FS Actuator Bracket 131 0437 M6/16 Bolt 1032 0709 M6 C Washer 1033 2914FO Feed Tray 134 18000 AV Mount 835 1511 M16 P Nyloc Nut 436 18115 M8/50 Csk Soc. 137 1006 M4/30 Pan Pozi 238 4345 M10 P Nyloc Nut 139 2493 Rubber Cap 240 0712 M8 C Washer 841 0142 M6 P Nyloc Nut 842 18104 M5/12 Pan Pozi 443 0857 M5 A Washer 444 18924 Square Reflector 245 18102 M5 T Nyloc Nut 246 P*144 Operator’s Manual Cannister 147 0347 M8/20 Button Head 348 0481 M8 T Nyloc Nut 4
21
30 35
8
32
36
7 340 48
37
38
39
17
x4
2
3
45
6
7
13
41
34
4342
44 45
x4
x3
40
46
47
48
TIMBERWOLFTW S426TDHB47 HYDRAULICS
Date Last Modified: 4th Jan 2015
Item Part No Part Name q’ty1 18525 Hose 3/4” 12 17813 Hose 1/2” 13 17812 Hose 1/2” 14 17815 Hose 1/2” 15 17814 Hose 1/2” 16 1660 Hydraulic Pump 17 0396 3/8 Dowty Seal 68 0026 Adaptor mm 1/2”- 3/8” BSP 59 0100 Filter 110 18170 M8/30 Bolt 211 0711 M8 A Washer 2 12 1434 Tank Top Filter Housing 113 1067 Breather Filter 114 1658 M6/12 Bolt 8
Item Part No Part Name q’ty15 0709 M6 C Washer 816 1702FS Tank Top Plate 117 0398 1/2 Dowty Seal 418 1583 Adaptor 1/2”- 3/4” BSP 119 4252 Directional Control Valve 120 1766 Adapter 3/4” - 3/4” BSP 121 0152 3/4 Dowty Seal 122 1703 Tank 123 0211 3/8” BSP Plug 124 4219 3/4” Tapered Blanking Plug 125 0027 Adaptor 1/2”- 1/2” BSP 226 17810 Motor 127 17777FS Hydraulic Tank Strap 1
3
5
12
4
22
121718
10
11
13
9
67
8
78
8
2
3
19
1
17
18
20 21
24
23
2617
25
45
14
15
16
727
PH TIMBERWOLFTW S426TDHB 48ROLLER BOX
Dat
e La
st M
odifi
ed: 2
5th
Mar
ch 1
0
x4
x4
x4
x3
x2
x4x4
x2
x8
x10
121
4
5
3
98 13
12 1415
11
16
17
1819
20
21
2223
2425
10
37 38
6
78
9
31
3332
34
2120
26
27
2829
23
35
1
2130
39
1913
Item
Par
t No
Par
t Nam
eq
’ty1
0644
M12
P N
yloc
Nut
52
0702
M12
A W
ashe
r4
317
556S
Top
Pla
te1
417
775F
STo
p G
uard
Bra
cket
15
1857
1FB
Rol
ler
Box
16
1760
9Fl
ap10
717
608F
SFl
ap H
olde
r10
807
01M
10 A
Was
her
139
4345
M10
P N
yloc
Nut
1310
1812
M10
/35
Bol
t10
1117
557
Top
Rol
ler
Slid
e A
ssem
bly
112
3009
Slid
e P
lug
813
1780
8AV
Mou
nt3
1417
21M
8/10
Bol
t2
1507
14M
8 P
enny
Was
her
2
Item
Par
t No
Par
t Nam
eq
’ty16
1755
3A
nvil
117
1818
1M
16/3
5 C
aphe
ad5
1817
810
Mot
or1
1919
85M
12/3
0 C
aphe
ad8
2003
21M
12/3
0 B
olt
621
0704
M12
C W
ashe
r9
2217
662M
Nyl
ube
Bus
h1
2303
86M
10/3
0 C
aphe
ad8
2418
628M
Non
-Mot
or D
rive
Bos
s1
2517
615
Spa
cer
Pla
te S
tub
126
1757
1C
entr
e P
late
Rol
ler
127
1757
0S
plin
e D
rive
End
Pla
te1
2818
379
315m
m T
ube
129
1801
6M14
T S
plin
e D
rive
130
1801
712
mm
x 4
0mm
Dow
els
2
Item
Par
t No
Par
t Nam
eq
’ty31
0839
Layf
lat S
prin
g P
rote
ctor
432
2116
Spr
ing
433
4333
M12
/170
Bol
t1
3417
774F
SS
prin
g H
ange
r B
rack
et1
3504
29M
12/3
5 B
olt
236
1847
4R
otat
ing
Fitt
ing
137
1756
8R
olle
r B
lade
s8
3818
059
M16
/35
Csk
Scr
ew24
3918
285
M16
Nor
dloc
k W
ashe
r5
4018
475
Buf
fer
Con
e2
4118
192
Rem
ote
Gre
aser
142
150m
m x
5m
m P
ipe
143
0479
M8
P N
yloc
Nut
244
0712
M8
C W
ashe
r2
41 42 36
40
9 8
43 44
2
TIMBERWOLFTW S426TDHB49
Date:
Hours:
Invoice number:
Signature:
Next service due:
WARRANTY SERVICE CHECK RECORD
50 HOUR SERVICE
Date:
Hours:
Invoice number:
Signature:
Next service due:
11 MONTH WARRANTY SERVICE CHECK
Date:
Hours:
Invoice number:
Signature:
Next service due:
Authorised dealer stamp23 MONTH WARRANTY SERVICE CHECK
Authorised dealer stamp
Authorised dealer stamp
TIMBERWOLFTW S426TDHB 50
Date:
Hours:
Invoice number:
Signature:
Next service due:
Authorised dealer stamp
Date:
Hours:
Invoice number:
Signature:
Next service due:
Authorised dealer stamp
Date:
Hours:
Invoice number:
Signature:
Next service due:
Authorised dealer stamp
Date:
Hours:
Invoice number:
Signature:
Next service due:
Authorised dealer stamp
SERVICE RECORD
timberwolf-uk.com
Timberwolf Wood Chippers & ShreddersTomo Industrial Estate, Stowmarket, Suffolk IP14 5AY, United KingdomT: +44 1449 765809 E: [email protected] W: timberwolf-uk.com