+ All Categories
Home > Documents > Instructions UFO Mk1 - Sirrob01 · PDF fileI designed the UFO MK-1 to be used with Okumarts...

Instructions UFO Mk1 - Sirrob01 · PDF fileI designed the UFO MK-1 to be used with Okumarts...

Date post: 23-Feb-2018
Category:
Upload: letruc
View: 217 times
Download: 1 times
Share this document with a friend
9
(Attribution-NonCommercial 3.0 Unported (CC BY-NC 3.0)
Transcript
Page 1: Instructions UFO Mk1 - Sirrob01 · PDF fileI designed the UFO MK-1 to be used with Okumarts Retro Aliens, ... Start at front side with tabs on both sides. Laser Assembly (Part No 14

(Attribution-NonCommercial 3.0 Unported (CC BY-NC 3.0)

Page 2: Instructions UFO Mk1 - Sirrob01 · PDF fileI designed the UFO MK-1 to be used with Okumarts Retro Aliens, ... Start at front side with tabs on both sides. Laser Assembly (Part No 14

Overview Assembly Diagram Solid Canopy

(Print Only Page 1 of PDF)

Introduction I designed the UFO MK-1 to be used with Okumarts Retro Aliens, but you should be able to use it with any kind of

alien, the cockpit and chair should be able to hold any kind of 25/30mm miniature metal alien. The model isn't

complex to build although the clear canopy and guns can be a little bit of a challenge. To finish off the weapons it's

handy to have a couple of 3-4 mm (1/8 inch) plastic beads to stick on the ends to complete that retro laser look.

Overview Assembly Diagram Clear Canopy (Print 2

nd page of PDF on clear transparency)

Page 3: Instructions UFO Mk1 - Sirrob01 · PDF fileI designed the UFO MK-1 to be used with Okumarts Retro Aliens, ... Start at front side with tabs on both sides. Laser Assembly (Part No 14

Overview Assembly Diagram Solid Canopy (Print 1

st page of PDF only)

Page 4: Instructions UFO Mk1 - Sirrob01 · PDF fileI designed the UFO MK-1 to be used with Okumarts Retro Aliens, ... Start at front side with tabs on both sides. Laser Assembly (Part No 14

Main Body Assembly (Part No 6)

Do not Glue part 5 into place

Outer Cockpit Tube (Part No 3 & 4)

Detailed Part Assembly

Page 5: Instructions UFO Mk1 - Sirrob01 · PDF fileI designed the UFO MK-1 to be used with Okumarts Retro Aliens, ... Start at front side with tabs on both sides. Laser Assembly (Part No 14

Inner Cockpit Tube (Part No 1 & 2)

Control Panel (Part No 10 & 11)

Canopy (Part No 17)

Start at front side with tabs on both sides

Page 6: Instructions UFO Mk1 - Sirrob01 · PDF fileI designed the UFO MK-1 to be used with Okumarts Retro Aliens, ... Start at front side with tabs on both sides. Laser Assembly (Part No 14

Laser Assembly (Part No 14 & 15)

End ball is 3-4mm plastic bead. If using a plastic bead don’t cap both ends of Laser tube

Engine/Base (Part No 16)

Page 7: Instructions UFO Mk1 - Sirrob01 · PDF fileI designed the UFO MK-1 to be used with Okumarts Retro Aliens, ... Start at front side with tabs on both sides. Laser Assembly (Part No 14

Chair Assembly (Part No 7, 8 & 9)

Rest (Part No 5, 12 & 13)

Page 8: Instructions UFO Mk1 - Sirrob01 · PDF fileI designed the UFO MK-1 to be used with Okumarts Retro Aliens, ... Start at front side with tabs on both sides. Laser Assembly (Part No 14

Detailed UFO Assembly

Page 9: Instructions UFO Mk1 - Sirrob01 · PDF fileI designed the UFO MK-1 to be used with Okumarts Retro Aliens, ... Start at front side with tabs on both sides. Laser Assembly (Part No 14

Recommended