Date post: | 19-Oct-2015 |
Category: |
Documents |
Upload: | enronbuster |
View: | 43 times |
Download: | 0 times |
of 41
www.DrSpeedometer.com [GM INSTRUMENT CLUSTER REMOVAL GUIDE]
1
03+ GM Instrument Cluster Removal Guide
Dear GM Owner,
Thank you for downloading my 03+ GM instrument cluster removal guide! I put this
guide together as a courtesy to my clients who want to remove their clusters themselves
to send in for repair. I hope that you find this guide useful and if you have any questions
about cluster removal or any aspect of GM cluster repair you can always contact me
24hrs a day at [email protected] or by phone, toll free at 1-800-405-1056,
Monday-Friday 9-5 CST.
Thanks!
Fred Dr.Speedometer Burge
www.drspeedometer.com
(P.S. Weve just added a bunch of really great looking cluster upgrade options to the
website such as blue and red LED lighting, colored needles and even white gauge faces
and theyre getting really popular. Check em all out here: Upgrade My Order!)
Have you received your free shipping label yet?
Please visit www.drspeedometer.com/how-to-buy for instructions on how to
place your order and receive your free shipping label.
www.DrSpeedometer.com [GM INSTRUMENT CLUSTER REMOVAL GUIDE]
2
Table of Contents:
Page 3: Silverado, Sierra, Suburban, Yukon, Tahoe, Avalanche, Escalade
Page 4: Trailblazer, Envoy, Rainier
Page 7: Aztec
Page 9: Monte Carlo
Page 11: Impala
Page 13: Cavalier
Page 16: Sunfire
Page 19: SSR
Page 26: Tracker
Page 28: Hummer H2
Page 30: Venture
Page 36: Rendezvous
www.DrSpeedometer.com [GM INSTRUMENT CLUSTER REMOVAL GUIDE]
3
Silverado, Sierra, Suburban, Yukon, Tahoe,
Avalanche, Escalade
Truck/full size SUV video is located on Youtube here.
1. Apply the parking brake to prevent the vehicle from moving
2. If equipped with and automatic transmission, move the shift lever all the way
down to last gear.
3. Tilt the steering wheel to the full down position
4. Pull gently rearward on the corners of the bezel from the instrument panel (IP)
assembly
5. Remove the bezel
6. After removing the trim plate bezel simply remove the four screws holding the
instrument cluster in place. Pull the cluster out and unplug the single wiring
harness connection in the back.
Trailblazer, Envoy, Rainier
www.DrSpeedometer.com [GM INSTRUMENT CLUSTER REMOVAL GUIDE]
4
1. Tilt the steering wheel to the full down position 2. Remove or lower the left closeout/insulator panel, see pic below:
3. Remove the 4 screws from the knee bolster trim panel, see pic below:
4. Remove the 6 screws retaining the bezel to the instrument panel (Chevrolet pic
below).
www.DrSpeedometer.com [GM INSTRUMENT CLUSTER REMOVAL GUIDE]
5
GMC and Buick version below (4 screws):
5. Remove the bezel from the instrument panel. (Chevrolet: by tilting it towards the
passenger side out of your way, its not necessary to remove the 4x4 or wiper
switch.) 6. After moving the trim plate bezel to the right, simply remove the four screws
holding the instrument cluster in place. Pull the cluster out and unplug the single
wiring harness connection in the back.
www.DrSpeedometer.com [GM INSTRUMENT CLUSTER REMOVAL GUIDE]
6
www.DrSpeedometer.com [GM INSTRUMENT CLUSTER REMOVAL GUIDE]
7
Aztek
1. Remove the knee bolster panel
2. Remove the front floor console trim plate
3. Remove the instrument panel (I/P) accessory trim plate.
4. Remove the 3 screws from the I/P cluster trim plate at the assist handle
5. Pull out the I/P cluster trim plate in order to release from the retainers.
6. From the back side disconnect the driver information center (DIC) from the I/P
cluster trim plate panel.
7. Loosen the steering column bracket and lower the steering column.
8. Remove the I/P cluster trim plate.
9. After removing the trim plate bezel simply remove the four screws holding the
instrument cluster in place. Pull the cluster out and unplug the single wiring
harness connection in the back.
www.DrSpeedometer.com [GM INSTRUMENT CLUSTER REMOVAL GUIDE]
8
www.DrSpeedometer.com [GM INSTRUMENT CLUSTER REMOVAL GUIDE]
9
Monte Carlo 1. Adjust the steering wheel for access.
2. Using a small flat-bladed tool, remove the bezel from the ignition switch
cylinder.
3. Remove the access cover from the left instrument panel (IP) fuse block.
4. Remove the steering column filler.
5. Open the IP compartment door.
6. Remove the screw from the left side of the IP cluster trim plate.
www.DrSpeedometer.com [GM INSTRUMENT CLUSTER REMOVAL GUIDE]
10
7. Remove the screw from the right side of the IP cluster trim plate
8. If the vehicle is equipped with a front floor console, position the transaxle shift
control lever to the rear most position.
10. After removing the trim plate bezel simply remove the four screws holding the
instrument cluster in place. Pull the cluster out and unplug the single wiring
harness connection in the back.
www.DrSpeedometer.com [GM INSTRUMENT CLUSTER REMOVAL GUIDE]
11
Impala
1. Apply the parking brake
2. Using a small flat-bladed tool, remove the bezel from the ignition switch cylinder.
3. If the vehicle is equipped with a column shift, position the transaxle shift control
indicator to 1. Keep the key in the ignition switch cylinder.
4. Adjust the steering wheel for access.
5. Remove the steering wheel filler panel
www.DrSpeedometer.com [GM INSTRUMENT CLUSTER REMOVAL GUIDE]
12
6. Remove the instrument panel (I/P) fuse block access hole covers.
7. Remove the screws from the I/P cluster trim plate.
8. Starting at the right end of the I/P cluster, grasp the trim plate and pull rearward.
9. Continue working around the I/P cluster trim plate until all of the retainers are
released from the I/P trim pad.
10. Disconnect the electrical connectors from the hazard switch and from the traction
control switch, if equipped.
11. Remove the I/P cluster trim plate.
12. After removing the trim plate bezel simply remove the four screws holding the
instrument cluster in place. Pull the cluster out and unplug the single wiring
harness connection in the back.
www.DrSpeedometer.com [GM INSTRUMENT CLUSTER REMOVAL GUIDE]
13
Cavalier
1. Remove the defroster grille screw
2. With flat bladed tool disengage the defroster grille from the instrument panel
(I/P)trim pad.
3. With flat bladed tool disengage the outer trim covers from the I/P carrier. Pull
the cover rearward to disengage the locating tabs from I/P carrier.
4. Open the I/P compartment.
5. Remove the I/P trim pad screws (1)
6. Remove the I/P trim pad (2) from the I/P carrier.
www.DrSpeedometer.com [GM INSTRUMENT CLUSTER REMOVAL GUIDE]
14
7. Remove the screws (1) from the I/P cluster trim panel. (3)
8. Remove the I/P cluster trim panel (3). Pull rearward in order to disengage the
retainers (2).
9. Disconnect the electrical connectors for the headlamp dimmer switch.
10. Disconnect the electrical connectors for the cigar lighter, if equipped.
www.DrSpeedometer.com [GM INSTRUMENT CLUSTER REMOVAL GUIDE]
15
11. Remove the screws (6) from the top of the I/P cluster (5).
12. Remove the I/P cluster (5) pulling rearward.
13. Disconnect the electrical connector (1) from the I/P cluster (5)
14. Remove the I/P cluster from the I/P.
www.DrSpeedometer.com [GM INSTRUMENT CLUSTER REMOVAL GUIDE]
16
Sunfire
1. Release the defroster grille (2) retainers using a small flat bladed tool.
2. Remove the grille (2) from the instrument panel (I/P) upper trim pad (1).
www.DrSpeedometer.com [GM INSTRUMENT CLUSTER REMOVAL GUIDE]
17
3. The air bag system does not need to be disabled if it the passenger air
bag is left connected during this process.
4. Remove the I/P upper trim panel (4) by lifting upward to release the
retainers.
5. Remove the screws from the I/P outer trim cover
6. Remove the I/P outer trim covers.
7. Remove the I/P accessory trim plate (3). Open the I/P compartment door
in order to access the screws (2).
8. Remove the screws (2) from the I/P accessory trim plate (3).
9. Pull the I/P trim plate (3) rearward to disengage the retainers.
10. Remove the I/P trim plate from the I/P carrier.
www.DrSpeedometer.com [GM INSTRUMENT CLUSTER REMOVAL GUIDE]
18
11. Remove the screws (1) from the right I/P trim panel.
12. Remove the right I/P trim panel (3).
13. Remove the screws (1) attaching the I/P trim pad (2).
14. Remove the I/P pad (2) from the I/P carrier.
www.DrSpeedometer.com [GM INSTRUMENT CLUSTER REMOVAL GUIDE]
19
SSR 1. Disconnect negative battery cable
2. Remove passenger seat to gain room
3. Remove Left trim panel using flat-bladed plastic tool, start at top edge,
release retaining clips
4. Remove right trim panel, first removing HVAC knobs
www.DrSpeedometer.com [GM INSTRUMENT CLUSTER REMOVAL GUIDE]
20
5. Remove glove box door
6. Remove left side knee bolster. Remove 3 screws holding knee bolster to
instrument panel
7. Unplug electrical connector (2) from headlamp switch
www.DrSpeedometer.com [GM INSTRUMENT CLUSTER REMOVAL GUIDE]
21
8. Remove right knee bolster Remove the ashtray door and 3 upper retaining
fasteners.
9. Remove the 2 left retaining fasteners.
10. Disconnect the airbag module disable switch.
11. Disconnect the I/P compartment light electrical connector (1).
www.DrSpeedometer.com [GM INSTRUMENT CLUSTER REMOVAL GUIDE]
22
12. Disconnect the bed cover electrical connector (2).
13. Disconnect the power point receptacle connector (1).
14. Remove bolster from vehicle.
15. Remove right airbag module. Using ratchet, an 8 inch extension with a
universal adapter and a 10mm deep well socket. Remove 2 upper airbag
fasteners (1).
16. Disconnect the airbag module connector position assurance.
17. Disconnect the airbag module electrical connector.
www.DrSpeedometer.com [GM INSTRUMENT CLUSTER REMOVAL GUIDE]
23
18. Remove the 2 lower airbag retaining bolts (1)
19. Remove the airbag from the front of the I/P cluster
20. Move steering wheel to full down position
21. Remove 5 fasteners from the center trim panel
www.DrSpeedometer.com [GM INSTRUMENT CLUSTER REMOVAL GUIDE]
24
22. Release retaining clips from the center trim panel and remove
23. Remove the instrument panel cluster seal from the IPC
24. Remove 4 screws that retain the cluster bezel to the I/P
25. Partially remove the cluster bezel to gain access to the electrical connections.
26. Disconnect the electrical connections and remove cluster from dash.
www.DrSpeedometer.com [GM INSTRUMENT CLUSTER REMOVAL GUIDE]
25
www.DrSpeedometer.com [GM INSTRUMENT CLUSTER REMOVAL GUIDE]
26
Tracker
1. Remove the 4 screws which secure the plastic trim piece that goes around
the cluster and radio area
2. Gently pry the trim piece away from the dash using a flat bladed tool, use
tape on the tool if necessary to prevent damage to plastic
3. Remove the 4 screws (1) that hold the cluster in place.
4. Pull the cluster forward to gain access to the electrical connectors
www.DrSpeedometer.com [GM INSTRUMENT CLUSTER REMOVAL GUIDE]
27
5. Disconnect the 3 electrical connectors (2) and remove the cluster from
the dash.
www.DrSpeedometer.com [GM INSTRUMENT CLUSTER REMOVAL GUIDE]
28
Hummer H2
1. First, remove trim panel by removing screws that hold cluster trim panel to instrument
panel
2. Use care to remove cluster trim panel from tabs in instrument panel
3. Now, remove the screws from the instrument cluster
www.DrSpeedometer.com [GM INSTRUMENT CLUSTER REMOVAL GUIDE]
29
4. Finally, disconnect the instrument cluster electrical connection.
www.DrSpeedometer.com [GM INSTRUMENT CLUSTER REMOVAL GUIDE]
30
Venture Instrument panel insulator right side:
1. Remove the push-in retainers from the IP (instrument panel) insulator to
instrument panel.
2. Remove the press-on retainers from the IP insulator to dash mat.
www.DrSpeedometer.com [GM INSTRUMENT CLUSTER REMOVAL GUIDE]
31
3. Unsnap the IP courtesy lamp from the IP insulator
4. Remove the IP insulator from the instrument panel
Instrument panel insulator left side:
5. Remove the push-in retainers from the IP insulator to instrument panel.
www.DrSpeedometer.com [GM INSTRUMENT CLUSTER REMOVAL GUIDE]
32
6. Remove the press-on retainers from the IP insulator to dash mat.
7. Unsnap the IP courtesy lamp from the IP insulator
8. Remove the IP insulator from the instrument panel
www.DrSpeedometer.com [GM INSTRUMENT CLUSTER REMOVAL GUIDE]
33
Knee Bolster
9. Remove the bolts/screws from the bottom of the knee bolster
10. Pull on the knee bolster in order to release the upper clips
Accessory Trim Plate
11. Open the ashtray or the cup holder.
12. Remove the following sets of screws:
www.DrSpeedometer.com [GM INSTRUMENT CLUSTER REMOVAL GUIDE]
34
- Two screws from the front of the trim panel. For access to the front screws,
remove the ashtray or the cupholder.
- Two screws from the bottom of the trim panel. For access to the bottom
screws, remove the console storage box.
13. Use a small, flat-bladed tool in order to remove the upper tabs on the IP
accessory plate from the instrument panel.
14. Disconnect the electrical connectors, if equipped.
15. Remove the IP accessory trim plate from the instrument panel.
Instrument Cluster Trim Plate
16. Position the tilt steering wheel to the lowest position.
17. Pull on the IP cluster trim plate in order to release the clips that secure the IP
cluster trim plate to the instrument panel. Begin near the headlamp switch and
work toward the center of the vehicle IP cluster trim plate.
18. Remove the IP cluster trim plate from the instrument panel.
Instrument Cluster Removal Important the ignition switch must be in the OFF position when removing the instrument
panel cluster.
www.DrSpeedometer.com [GM INSTRUMENT CLUSTER REMOVAL GUIDE]
35
19. Remove the screws from the IP cluster to instrument panel.
20. Remove the IP cluster from the instrument panel.
www.DrSpeedometer.com [GM INSTRUMENT CLUSTER REMOVAL GUIDE]
36
Rendezvous
Instrument panel insulator right side:
1. Remove the push-in retainers from the IP (instrument panel) insulator to
instrument panel. 2. Remove the press-on retainers from the IP insulator to dash mat.
www.DrSpeedometer.com [GM INSTRUMENT CLUSTER REMOVAL GUIDE]
37
3. Unsnap the IP courtesy lamp from the IP insulator
4. Remove the IP insulator from the instrument panel
Instrument panel insulator left side:
5. Remove the push-in retainers from the IP insulator to instrument panel.
www.DrSpeedometer.com [GM INSTRUMENT CLUSTER REMOVAL GUIDE]
38
6. Remove the press-on retainers from the IP insulator to dash mat.
7. Unsnap the IP courtesy lamp from the IP insulator
8. Remove the IP insulator from the instrument panel
www.DrSpeedometer.com [GM INSTRUMENT CLUSTER REMOVAL GUIDE]
39
Knee Bolster
9. Remove the bolts/screws from the bottom of the knee bolster
10. Pull on the knee bolster in order to release the upper clips
Driver Information Display Switch 11. Use a flat-bladed tool to pry the cover of the driver info center panel from the
instrument panel
www.DrSpeedometer.com [GM INSTRUMENT CLUSTER REMOVAL GUIDE]
40
12. Disconnect the electrical connectors from the driver info center panel and
remove.
Cluster Trim Plate Bezel Important: turn the ignition switch to the OFF position before you remove the instrument panel cluster.
13. Loosen the steering column bracket. Lower the steering column
14. Remove the trim plate bezel from the instrument panel cluster.
15. Remove the screws from the IP cluster.
16. Disconnect the electrical connectors from the IP cluster and remove.
www.DrSpeedometer.com [GM INSTRUMENT CLUSTER REMOVAL GUIDE]
41
If your vehicle is not covered by this guide please contact us by email at:
Disclaimer
This guide is not to be distributed, copied, reproduced or otherwise duplicated in any form either
online or offline.
Dr.Speedometer www.drspeedometer.com and/or Fred Burge accept(s) no responsibility for any
damage to person or property that may occur as a result of using this guide, this guide is intended for
informational purposes only. Please use all caution when working with tools, electronics and
electricity. By using this guide you accept and agree that any injury or damage suffered to person or
property as a result of using this guide is the sole responsibility of the user and will not hold
Dr.Speedometer or Fred Burge responsible or pursue any legal action whatsoever.
Ready To Order? Next step:
Please visit www.drspeedometer.com/how-to-buy to place your order and receive
your free shipping label.