Intel 852GM Small Form Factor Proof-of-Concept Board€¦ · 2intel® 852gm small form factor...

Intel® 852GM Small Form Factor Proof-of-Concept BoardUser’s Manual

March 2006

Order Number: 309239-002

2 Intel® 852GM Small Form Factor Proof-of-Concept Board User’s Manual

INFORMATION IN THIS DOCUMENT IS PROVIDED IN CONNECTION WITH INTEL® PRODUCTS. EXCEPT AS PROVIDED IN INTEL’S TERMS AND CONDITIONS OF SALE FOR SUCH PRODUCTS, INTEL ASSUMES NO LIABILITY WHATSOEVER, AND INTEL DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY RELATING TO SALE AND/OR USE OF INTEL PRODUCTS, INCLUDING LIABILITY OR WARRANTIES RELATING TO FITNESS FOR A PARTICULAR PURPOSE, MERCHANTABILITY, OR INFRINGEMENT OF ANY PATENT, COPYRIGHT, OR OTHER INTELLECTUAL PROPERTY RIGHT.

Intel Corporation may have patents or pending patent applications, trademarks, copyrights, or other intellectual property rights that relate to the presented subject matter. The furnishing of documents and other materials and information does not provide any license, express or implied, by estoppel or otherwise, to any such patents, trademarks, copyrights, or other intellectual property rights.

Intel products are not intended for use in medical, life saving, life sustaining, critical control or safety systems, or in nuclear facility applications.

Intel may make changes to specifications and product descriptions at any time, without notice.

Designers must not rely on the absence or characteristics of any features or instructions marked “reserved” or “undefined.” Intel reserves these for future definition and shall have no responsibility whatsoever for conflicts or incompatibilities arising from future changes to them.

The Intel® 852GM Small Form Factor Proof-of-Concept Board may contain design defects or errors known as errata which may cause the product to deviate from published specifications. Current characterized errata are available on request.

MPEG is an international standard for video compression/decompression promoted by ISO. Implementations of MPEG CODECs, or MPEG enabled platforms may require licenses from various entities, including Intel Corporation.

This User’s Manual as well as the software described in it is furnished under license and may only be used or copied in accordance with the terms of the license. The information in this manual is furnished for informational use only, is subject to change without notice, and should not be construed as a commitment by Intel Corporation. Intel Corporation assumes no responsibility or liability for any errors or inaccuracies that may appear in this document or any software that may be provided in association with this document.

Except as permitted by such license, no part of this document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means without the express written consent of Intel Corporation.

Contact your local Intel sales office or your distributor to obtain the latest specifications and before placing your product order.

Copies of documents which have an ordering number and are referenced in this document, or other Intel literature may be obtained by calling 1-800-548-4725 or by visiting Intel's website at http://www.intel.com.

AnyPoint, AppChoice, BoardWatch, BunnyPeople, CablePort, Celeron, Chips, CT Media, Dialogic, DM3, EtherExpress, ETOX, FlashFile, i386, i486, i960, iCOMP, InstantIP, Intel, Intel Centrino, Intel logo, Intel386, Intel486, Intel740, IntelDX2, IntelDX4, IntelSX2, Intel Create & Share, Intel GigaBlade, Intel InBusiness, Intel Inside, Intel Inside logo, Intel NetBurst, Intel NetMerge, Intel NetStructure, Intel Play, Intel Play logo, Intel SingleDriver, Intel SpeedStep, Intel StrataFlash, Intel TeamStation, Intel Xeon, Intel XScale, IPLink, Itanium, MCS, MMX, MMX logo, Optimizer logo, OverDrive, Paragon, PC Dads, PC Parents, PDCharm, Pentium, Pentium II Xeon, Pentium III Xeon, Performance at Your Command, RemoteExpress, SmartDie, Solutions960, Sound Mark, StorageExpress, The Computer Inside., The Journey Inside, TokenExpress, VoiceBrick, VTune, and Xircom are trademarks or registered trademarks of Intel Corporation or its subsidiaries in the United States and other countries.

*Other names and brands may be claimed as the property of others.

Copyright © 2006, Intel Corporation

http://www.intel.com

Contents

Contents1 Product Overview ............................................................................................................................6

1.1 Introduction ...........................................................................................................................61.2 Related Documents ..............................................................................................................61.3 Product Contents ..................................................................................................................71.4 Proof-of-Concept Board Features.........................................................................................71.5 SFF POC Board Block Diagram ...........................................................................................9

2 Installation Guide for POC Board ..................................................................................................11

2.1 Before You Begin................................................................................................................112.2 Setting up the SFF POC Board ..........................................................................................11

3 Connectors and Jumpers ..............................................................................................................15

3.1 List of Jumpers ...................................................................................................................163.2 List of Connectors ...............................................................................................................18

Figures1 SFF POC Board Block Diagram ...................................................................................................92 SFF Placement - Top View.........................................................................................................103 Assembled Board, Front View ....................................................................................................124 20-pin Power Supply Connector .................................................................................................145 SFF POC Board Connectors and Jumpers ................................................................................156 SFF POC Board Solder Side ......................................................................................................16

Tables1 Related Documents ......................................................................................................................62 Additional Hardware ...................................................................................................................113 Jumper Settings..........................................................................................................................124 Jumpers ......................................................................................................................................166 LCD Voltage Selection (JP2) ......................................................................................................177 COM2 RS-232/422/485 Selection (JP3).....................................................................................178 COM2 RS-232/422/485 Selection (JP4).....................................................................................179 RI/+5V/+12V Selection (JP5)......................................................................................................175 Clear CMOS (JP1)......................................................................................................................1710 Connectors .................................................................................................................................1811 USB Connector (CN1) ................................................................................................................1812 USB Connector (CN2) ................................................................................................................1913 Primary IDE Hard Drive Connector (CN3) ..................................................................................1914 Digital IO Connector (CN4).........................................................................................................2015 Front Panel (CN5).......................................................................................................................2016 Serial Port COM2 Connector (CN6) RS-232 Mode ....................................................................2017 Serial Port COM2 Connector (CN6) RS-422 Mode ....................................................................2018 Serial Port COM2 Connector (CN6) RS-485 Mode ....................................................................2119 Parallel Port Connector (CN7) ....................................................................................................21

Intel® 852GM Small Form Factor Proof-of-Concept Board User’s Manual 3

Contents

20 Dual Channel LVDS Connector (CN8) .......................................................................................2121 4P Power Connector (CN9)........................................................................................................ 2222 TV-out Connector (CN10)........................................................................................................... 2223 DVI Connector (CN11) ............................................................................................................... 2224 Audio Input/Output Connector (CN12) .......................................................................................2325 Ethernet 10/100BaseT RJ-45 Phone Jack Connector (CN13) ................................................... 2326 External 5VSB/PWRGD Connector (CN14) ............................................................................... 2327 IrDA Connector (CN15) .............................................................................................................. 2328 Fan Connector (CN16) ............................................................................................................... 2429 Mini-DIN PS/2 Connector (CN17)............................................................................................... 2430 Serial Port COM1 Connector (CN18) .........................................................................................2431 CRT Display Connector (CN19) ................................................................................................. 2532 External Battery (VBA T2) .......................................................................................................... 2533 Compact Flash Disk Slot (CFD) ................................................................................................. 25


Contents

Revision History

Date Revision Description

March 2006 002 Updated with branding changes.

September 2005 001 Initial release


Product Overview

Product Overview 1

1.1 Introduction

The POC board utilizes the Ultra Low Voltage Intel® Celeron® M or Mobile Intel® Celeron®

processor, Intel® 852GM chipset and the Intel® FW82801DB I/O Controller Hub. It is a fanless design which provides higher processing capability with excellent power consumption control. It offers a stable and efficient solution for customer who is seeking a trade-off between high performance and low power consumption. The POC board supports multiple display modes including CRT, LCD, DVI and TV-out. With the dimension of 146 mm X 102 mm, SFF also has the expansion capability through on-board Mini-PCI slot.

1.2 Related Documents

For more information, please contact your Intel local representative.

Table 1. Related Documents

Intel Order Number Document Location

251308 Mobile Intel® Celeron® Processor Datasheet www.intel.com/design/mobile/datashts/251308.htm

300302 Intel® Celeron® M Processor Datasheet www.intel.com/design/mobile/datashts/300302.htm

252407 Intel® 852GM Chipset (GMCH) Datasheet www.intel.com/design/mobile/datashts/252407.htm

290744 Intel® 82801DB I/O Controller Hub 4 (ICH4) Datasheet www.intel.com/design/chipsets/datashts/290744.htm

290745 Intel® 82801DB I/O Controller Hub 4 (ICH4) Specification Update

http://developer.intel.com/design/chipsets/specupdt/290745.htm

252338 Intel® 852GM Chipset Platform Design Guide www.intel.com/design/mobile/desguide/252338.htm


www.intel.com/design/mobile/datashts/251308.htm



www.intel.com/design/chipsets/datashts/290744.htm

www.intel.com/design/chipsets/datashts/290744.htm

http://developer.intel.com/design/chipsets/specupdt/290745.htm

www.intel.com/design/mobile/desguide/252338.htm

Product Overview

1.3 Product Contents

The SFF POC board is shipped with the following peripherals and features:

• One SFF POC Board with heat sink

• One IDE cable

• One Keyboard/Mouse cable

• Two USB cables

• One Audio cable

• One COM port cable

• One TV-out and S-terminal cable

• One DVI cable

• One Parallel port cable

• One Jumper cap

1.4 Proof-of-Concept Board Features

The proof-of-concept board features are summarized as below:

System:

• CPU: Onboard Intel® Celeron® M Processor Ultra Low Voltage 600 MHz 512K L2 Cache or Mobile Intel Celeron Processor at 600MHz Processor

• Memory: 200-pin DDR 266MHz SODIMM x 1, Max. 1GB

• Chipset: Intel 852GM chipset + Intel® 82801DB I/O Controller Hub 4 (ICH4)

• I/O Chipset: ITE IT8712F

• Ethernet: Intel® 82562 Fast Ethernet Controller, 10/100Base-TX RJ-45

• BIOS: AWARD 512KB FLASH ROM

• Watchdog Timer: Generate a Time-out System Reset

• SSD: Type II CompactFlash* slot x 1

• Expansion Interface: Type III Mini PCI Socket x 1

• Battery: Lithium battery

• Power Supply Voltage: +5V. AT/ATX

• Board Size: 5.75”(L) x 4”(W) (146mm x 102mm)

• Gross Weight: 0.55lb(0.4kg)

• Operating Temperature: 32ºF~140ºF (0ºC~60ºC)


Product Overview

Display:

• Chip: Intel 852GM chipset + Chrontel 7009

• Memory: Shared System Memory Up to 64 MB with DVMT

• Resolutions: Up to 1280 x 1024 @ 32bpp Colors for CRT and Up to 1280 x 1024 @ 24 bpp Colors for LCD

• TV-Out: Supports NTSC and PAL standard;

I/O:

• Miscellaneous: EIDE x 1(UDMA33 x 1), KB + Mouse x 1, RS-232 x 1, RS-232/422/485 x 1, Parallel x 1

• IrDA: IrDA Tx/Rx Header x 1

• Audio: MIC in, Line in, Line out 5.1 Output

• USB: Two 5 x 2 Pin Headers Support 4 USB 2.0 Ports


Product Overview

1.5 SFF POC Board Block Diagram

Figure 1. SFF POC Board Block Diagram

DDR266

Clock Synthesizer

mFCBGAIntel® Celeron® M

processor

Intel® 82852GM/GME Graphics Controller

400MHz FSB

Intel® 82801DB I/O Controller Hub 4

(ICH4)

Intel® 82562ET Fast

Ethernet Controller


Product Overview

For more details information on connectors’ placement, please refer to Chapter 3, “Connectors and Jumpers”.

Figure 2. SFF Placement - Top View

Intel® 82801DB I/O Controller Hub 4 (ICH4)

Intel® 852GM chipset


Installation Guide for POC Board

Installation Guide for POC Board 2

2.1 Before You Begin

Table 2 represents the additional hardware you may require to set up the board.

2.2 Setting up the SFF POC Board

Gather the hardware described in Table 2 and follow the steps below to set up the POC board. This manual assumes you are familiar with basic concepts of installing and configuring hardware for an x86 architecture platform.

1. Ensure a static-free work environment. Static-free procedures must be completed before removing any components from various anti-static packaging. The POC board is susceptible to electrostatic discharge (ESD), which may cause product failure or unpredictable operation.

Warning: Connecting the wrong cable or reversing a cable may damage the POC board and the device being connected. Since the board is not in a protective chassis, use caution when connecting cables to this product.

2. Verify contents. Inspect the contents of your kit and make sure that everything listed in Section 2.1 is included. Check for damage that may have occurred during shipment.

3. Check jumper settings. Verify that the following jumpers are set in their default state (see Table 3).

Table 2. Additional Hardware

Component Description

VGA Monitor Standard VGA or greater resolution monitor

Keyboard Keyboard with a PS/2 connector or adapter

Mouse Mouse with a PS/2 connector or adapter

IDE DevicesUp to two IDE devices can be connected to the POC board. One cable is included in this kit. The cable accommodates the included hard drive and one other IDE device, such as a CD-ROM drive or another hard drive.

Network AdapterAn Intel® 82562ET Ethernet Controller is included in the development kit. A CAT-5 cable with an RJ-45 connector is required to connect this Ethernet adapter to local area network.

AT Power Supply Require an AT power supply to power the board. If you are using ATX power supply, some minor work is required.

Memory Require one module of 200-pin DDR266 SODIMM (max 1 GB)

Other Devices and Adapters

Many PC compatible peripherals can be attached and configured to work with the POC board. For example, to install an additional network adapter into the mini PCI slot. Procuring and installing any drivers required for additional devices will need to be done by user.



4. Verify installed hardware. Make sure the following hardware is populated on your POC board:

• One Onboard Intel® Celeron® M processor 1.3 GHz, mFCBGA479 package

• BIOS FWH

• Battery

• Heatsink

Note: If the above hardware is not installed correctly, DO NOT apply power to the board. Correctly re-install the components before proceeding.

5. Install memory. Install the SO-DIMM in memory slot DIMM1. Insert the SO-DIMM above the slot (the DIMM is keyed so that it only fits in the slot in one orientation). Firmly, but carefully, insert the SO-DIMM into the slot until the tabs close.

Table 3. Jumper Settings

Jumper Function Default Setting

J1 Clear CMOS 1-2 Normal

J2 LCD Voltage Selection 1-2 +5 V

J3 COM2 RS-232/422/485 Mode Selection - 1 1-2 RS232

J4 COM2 RS-232/422/485 Mode Selection - 1 1-2 RS232

J5 COM2 RI/+5V/+12V Selection 5-6 RI

Figure 3. Assembled Board, Front View



6. Install storage devices. There is one IDE connector on the POC board that supports two IDE devices—a master and a slave. Attach the unconnected pin 41-43 header to the board. For a correct boot-up of the system, the included hard drive must be installed as the primary master.

Note: Master/slave settings are determined by a jumper on each IDE device. Consult the device label/documentation to verify that the jumper is set correctly for your configuration.

7. A CD-ROM drive or additional hard drive may be installed as a primary slave device. To install the included hard drive on the POC board:

a. Verify that the jumper on the hard drive is set correctly for single or master, depending on your configuration.

b. Connect the end of the IDE cable (pin 41-43) to the IDE connector CN3 on the board. Ensure that the tracer on the cable is aligned with pin 1 of the connector.

c. Connect the middle connector of the cable to the hard drive. Again, ensure that the cable tracer is aligned with pin 1 of the connector.

Warning: Failure to properly align the IDE cable may damage the POC board and/or the hard drive.

d. Connect the four-pin power connector from the power supply to the hard drive.

8. Install the CD-ROM drive (optional). A CD-ROM drive is not included in the kit and is not required, but it may be useful in loading additional software. To install it on the POC board:

a. Verify that the jumper on the CD-ROM drive is set for slave.

b. Connect the unused end of the IDE cable you already attached to the POC board to the CD-ROM drive. Ensure that the cable tracer is aligned with pin 1 of the CD-ROM drive connector.

c. Connect a large four-pin power connector from the power supply to the CD-ROM drive.

9. Connect the monitor. Connect the monitor cable to the VGA port.

10. Connect the keyboard and mouse. Connect the KB/Mouse cable to the Mini-Din PS/2 connector CN17 on the POC board. Then connect a PS/2 mouse and keyboard to the KB/Mouse cable. Alternatively, USB keyboard and a USB mouse maybe plug into one or both of the USB connectors on the POC board. Note that a legacy (PS/2) keyboard may be required for BIOS setup.

Note: Prior to connect the USB keyboard and USB mouse, you must first have the USB cable connect to the connector CN1 or CN2 on the POC board.

11. Connect the power supply. Make sure the power supply is turned off and unplugged. Connect the AT 4P power supply cables to connector CN9 on the POC board. Next, plug the power cord into the power supply and the wall.

12. Power up the system. Turn on the monitor and follow by the power supply. If you are using the ATX power supply, then you will need to short the pin15 (black) and pin14 (green) of the 20pin power supply connector in order to power up the system.

Warning: Loose jumper wire could lead to intermittent power which could eventually damage the POC board or cause electrical short to the user.



Warning: Powering up without all components installed correctly can lead to a failure that can damage the board. Do not apply power to the board until any loose components are fixed.

§ §

Figure 4. 20-pin Power Supply Connector


Connectors and Jumpers

Connectors and Jumpers 3

This section describes the placement of the connectors as well as setting jumpers setting on the board.

Figure 5. SFF POC Board Connectors and Jumpers

910

12

11

2

1

8

7

JP1

CN

1

CN

2

CN

4

CN

5

CN

6

JP3

JP

4

JP

5

JP2

CN19

CN9

CN14

CN17

CN16

CN8

CN11

CN10

CN18

CN13

CN15

CN

12

CN

7

CN

3

M PC I1



3.1 List of Jumpers

Table 4 must be used in setting the jumpers on the POC board. These tables give details about the jumpers shown in Figure 5and Figure 6. The jumpers allow configuring the system to user’s application. The table below shows the function of each of the board’s jumpers:

Figure 6. SFF POC Board Solder Side

CFD1

DIMM1

Table 4. Jumpers

Label Function

JP1 Clear CMOS

JP2 LCD Voltage Selection

JP3 COM2 RS-232/422/485 Mode Selection – 1

JP4 COM2 RS-232/422/485 Mode Selection – 2

JP5 COM2 RI /+5 V /+12 V Selection



Table 5. Clear CMOS (JP1)

JP1 Function

1-2 Normal (Default)

2-3 Clear CMOS

Table 6. LCD Voltage Selection (JP2)

JP2 Function

1-2 +5 V

2-3 +3.3 V (Default)

Table 7. COM2 RS-232/422/485 Selection (JP3)

JP3 Function

1-2, 4-5, 7-8, 10-11 RS-232 (Default)

2-3, 5-6, 8-9, 11-12 RS-422

2-3, 8-9 RS-485

Table 8. COM2 RS-232/422/485 Selection (JP4)

JP4 Function

1-2 RS-232(Default)

3-4 RS-422

5-6 RS-485

Table 9. RI/+5V/+12V Selection (JP5)

JP5 Function

5-6 RI(Default)

3-4 +5 V

1-2 +12 V



3.2 List of Connectors

The POC board has a number of connectors configuring the system to user’s application. The table below shows the function of each board’s connectors:

Table 10. Connectors

Label Function

CN1 USB 2.0 Port 1 Connector

CN2 USB 2.0 Port 2 Connector

CN3 Primary IDE Hard Drive Connector

CN4 Digital I/O Connector

CN5 Front Panel

CN6 Serial Port COM2 Connector

CN7 Parallel Port 1 Connector

CN8 Dual Channel LVDS Connector

CN9 4P Power Connector

CN10 TV-Out Connector

CN11 DVI Connector

CN12 Audio Input/Output Connector

CN13 Ethernet 10/100BaseT RJ-45 Phone Jack

CN14 External 5VSB/PWRGD Connector

CN15 IrDA Connector

CN16 Fan Connector

CN17 Mini-Din PS/2 Connector

CN18 Serial Port COM1 Connector

CN19 CRT Display Connector

MPCI1 Mini-PCI Slot

CFD1 CompactFlash* Disk Slot

Table 11. USB Connector (CN1)

Pin Signal Pin Signal

1 USBVDD0-1 2 GND

3 USBD0- 4 GND

5 USBD0+ 6 UDBD1+

7 GND 8 USBD1-

9 GND 10 USBVDD0-1



Table 12. USB Connector (CN2)


1 USBVDD2-3 2 GND

3 USBD2- 4 GND

5 USBD2+ 6 UDBD3+

7 GND 8 USBD3-

9 GND 10 USBVDD2-3

Table 13. Primary IDE Hard Drive Connector (CN3)


1 PRI_IDERST# 2 GND

3 PDD7 4 PDD8

5 PDD6 6 PDD9

7 PDD5 8 PDD10

9 PDD4 10 PDD11

11 PDD3 12 PDD12

13 PDD2 14 PDD13

15 PDD1 16 PDD14

17 PDD0 18 PDD15

19 GND 20 N.C.

21 PDREQ 22 GND

23 PDIOW# 24 GND

25 PDIOR# 26 GND

27 PIORDY 28 GND

29 PDDACK# 30 GND

31 IRQ14 32 N.C.

33 PDA1 34 P66DET

35 PDA0 36 PDA2

37 PDCS#1 38 PDCS#3

39 IDEACTP# 40 GND

41 +5V 42 +5V

43 GND 44 N.C.



Table 14. Digital IO Connector (CN4)


1 DIN_IN0 2 DIN_IN1

3 DIN_IN2 4 DIN_IN3

5 DIO_OUT0 6 DIO_OUT1

7 DIO_OUT2 8 DIO_OUT3

9 +5V 10 GND

Table 15. Front Panel (CN5)

Pin Signal

1-2 ATX Power-On Button

3-4 HDD Active LED

5-6 External Speaker

7-8 Power LED

9-10 System Reset Button

Table 16. Serial Port COM2 Connector (CN6) RS-232 Mode


1 DCDB 2 RXB

3 TXB 4 DTRB

5 GND 6 DSRB

7 RTSB 8 CTSB

9 RIB 10 N. C.



1 TXD- 2 RXD+

3 TXD+ 4 RXD-

5 N. C. 6 N. C.

7 N. C. 8 N. C.

9 GND 10 N. C.





1 TXD- 2 N.C.

3 TXD+ 4 N. C.

5 N. C. 6 N. C.

7 N. C. 8 N. C.

9 GND 10 N. C.

Table 19. Parallel Port Connector (CN7)


1 STBX 2 AFD#

3 PTD0 4 ERR#

5 PTD1 6 PINIT#

7 PTD2 8 SLIN#

9 PTD3 10 GND

11 PTD4 12 GND

13 PTD5 14 GND

15 PTD6 16 GND

17 PTD7 18 GND

19 ACK# 20 GND

21 BUSY 21 GND

23 PE 23 GND

25 SLCT 26 N. C.

Table 20. Dual Channel LVDS Connector (CN8) (Sheet 1 of 2)


1 Back-Light Enable 2 Back-Light Control

3 LCD Volt. 4 GND

5 TXLCLK# 6 TXLCLK

7 LCD Volts 8 GND

9 TXL0# 10 TXL0

11 TXL1# 12 TXL1

13 TXL2# 14 TXL2

15 TXL3# 16 TXL3

17 LVDS_DATA 18 LVDS_CLK



19 TXU0# 20 TXU0

21 TXU1# 22 TXU1

23 TXU2# 24 TXU2

25 TXU3# 26 TXU3

27 LCD Volt. 28 GND

29 TXUCLK# 30 TXUCLK

Table 21. 4P Power Connector (CN9)

Pin Signal

1 +5 V

2 GND

3 GND

4 +12 V

Table 22. TV-out Connector (CN10)


1 Y 2 CVBS

3 GND 4 GND

5 C 6 N. C.

7 GND 8 N. C.

Table 23. DVI Connector (CN11)


1 TD1 2 TD1#

3 GND 4 GND

5 TDC 6 TDC#

7 GND 8 +5 V

9 HPDET 10 +5 V

11 TD2 12 TD2#

13 GND 14 GND

15 TD0 16 TD0#

17 N.C. 18 N.C.

19 DVI_DATA 20 DVI_CLK

Table 20. Dual Channel LVDS Connector (CN8) (Sheet 2 of 2)



Table 24. Audio Input/Output Connector (CN12)


1 MIC_IN 2 MIC_Vcc

3 Audio GND 4 CD_GND

5 LINE_IN L 6 CD_L

7 LINE_IN R 8 CD_GND

9 Audio GND 10 CD_R

11 LINE_OUT L 12 LINE_OUT R

13 Audio GND 14 Audio GND

Table 25. Ethernet 10/100BaseT RJ-45 Phone Jack Connector (CN13)


1 TX+ 2 TX-

3 TCT 4 N.C.

5 N.C. 6 RCT

7 RX+ 8 RX-

9 LINK_LED 10 ACT_LED

11 SPD_LED 12 +3.3V

Table 26. External 5VSB/PWRGD Connector (CN14)

Pin Signal

1 N. C.

2 GND

3 N, C,

4 GND

5 PS_ON

6 +5 V (Standby)

Table 27. IrDA Connector (CN15)

Pin Signal

1 +5 V

2 N. C. (CIR_Tx_Option)

3 Rx



4 GND

5 Tx

6 N. C. (CIR_Tx_Option)

Table 28. Fan Connector (CN16)

Pin Signal

1 Fan Sense

2 +5 V

3 GND

Table 29. Mini-DIN PS/2 Connector (CN17)


1 Keyboard Data 2 Mouse Data

3 GND 4 Shield

5 +5 V 6 Keyboard Clock

7 Shield 8 Mouse Clock

Table 30. Serial Port COM1 Connector (CN18)


1 DCDA 2 RXA

3 TXA 4 DTRA

5 GND 6 DSRA

7 RSTA 8 CTSA

9 RIA 10 N. C.

Table 27. IrDA Connector (CN15)



Table 31. CRT Display Connector (CN19)


1 CRT_RED 9 5 V

2 CRT_GREEN 10 VGA GND

3 CRT_BLUE 11 N.C.

4 N.C. 12 CRT_SDA

5 VGA GND 13 CRT_HSYNC

6 VGA GND 14 CRT_VSYNC

7 VGA GND 15 CRT_SCL

8 VGA GND

Table 32. External Battery (VBA T2)

Pin Signal

1 VBAT (+3.3 V)

2 GND

Table 33. Compact Flash Disk Slot (CFD) (Sheet 1 of 2)


1 GND 26 GND

2 SDD3 27 SDD11

3 SDD4 28 SDD12

4 SDD5 29 SDD13

5 SDD6 30 SDD14

6 SDD7 31 SDD15

7 SDCS#1 32 SDCS#3

8 GND 33 GND

9 GND 34 SDIOR#

10 GND 35 SDIOW#

11 GND 36 +5 V

12 GND 37 IRQ15

13 +5 V 38 +5V

14 GND 39 CSEL#

15 GND 40 N.C.

16 GND 41 IDERST#

17 GND 42 SIORDY



18 SDA2 43 DMAREQ

19 SDA1 44 DMAACK

20 SDA0 45 DASP#

21 SDD0 46 PDIAG#

22 SDD1 47 SDD8

23 SDD2 48 SDD9

24 N.C. 49 SDD10

25 GND 50 GND

Table 33. Compact Flash Disk Slot (CFD) (Sheet 2 of 2)



Date post:	14-Jun-2020
Category:	Documents
Upload:	others
View:	0 times
Download:	0 times