© 2008 Autodesk 1

Inventor 2009 - What’s New

First and Last Name Presenter’s Title

© 2008 Autodesk 2

Simulation

Perform more advanced analysis with less setup time

What’s NewParametric Gear JointsReference FramesSpatial Joint3D Contact EnhancementPrecise Contact EventsCreate new traces during simulationOutput to Inventor Studio

© 2008 Autodesk 3

Simulation

Reduce the time needed to learn and use simulation tools

What’s NewColor display of rigid groupsPan and zoom control for input and output graphersImproved scale readabilityOutput variable names

© 2008 Autodesk 4

Part Modeling

Incorporate imported part geometry with fewer intermediate work steps

What’s NewChamfer, Fillet, 면기울기에Apply button 추가Shell – tangent face controlFillet – Minimal bend optionExtrude – To Point optionBoundary Patch – improved default tangency3D Grip – enhanced preview

Image Courtesy Adept Airmotive

© 2008 Autodesk 5

Tube & Pipe

Design self-draining process lines for sterility and clean-ability requirements

What’s NewGravity vectorSelf draining tube and pipe stylesASME BPE fittings libraryAuto-route self draining linesEnhanced Routing Tool

© 2008 Autodesk 6

Frame Generator

Incorporate custom frame sections in the design

What’s NewUser defined section profilesMultiple element insert Improved content migration

© 2008 Autodesk 7

Belt Generator

Streamline the design process for synchronous belt drives

What’s NewInitial start positionSketch representationTeeth representation

© 2008 Autodesk 8

Gear Generator

Spend less time designing reduction gears

What’s New3D grips for faster adjustment of gear dimensionsANSI/AGMA 2001-D04 strength check for spur and bevel gears.Bevel gear preview now shows helical teethNew Start Plane flip button

© 2008 Autodesk 9

Shaft Generator

Complete the as-manufactured shaft design without additional modeling steps

What’s NewInner and outer threads, keyway grooves with one rounded endPlain keyway grooves Chamfer for n-sided prismInner Bore Features:

chamfers, threads and grooves for inner retaining rings

New O-ring generator

© 2008 Autodesk 10

디자인액셀러레이터

Belt 디테일• Solid• Sketch• Detail

Feature 편집기능• 잠금• i-Feature 편집

Bolt 연결-장공에결합기능

Bolt 연결-• 패턴자동찾기• 돌출명령의홀인식• Sheetmetal fastner추가

© 2008 Autodesk 11

Vault Workflows

Spend less time dealing with the Vault and more time working on your design

What’s NewSingle Step Check InDWF Check in optimized Direct Access from File DialogsLLower Browser OverheadOD SupportSeparate Server Log in

© 2008 Autodesk 12

Improved Publishing

Facilitate design reviews for people without specialized viewers

What’s NewDWFx output for native IE7 viewing2D PDF outputHigher publishing speeds

© 2008 Autodesk 13

DWF Publishing

Output more accurate and consistent representation of parts and assemblies with better performance

What’s NewExpress optionPreserve the Inventor perspective view setting & environment mapMultiple decal output

© 2008 Autodesk 14

Wire & Harness

Multi node move /rotate

Harness Setting

업데이트연기

© 2008 Autodesk 15

Working with Larger Assemblies

Work on very complex machines and assemblies

What’s New64 Bit SupportAssembly SubstitutionMemory reduction for Derived PartsPerformance Optimization

© 2008 Autodesk 16

Full 64 Bit Support

Take advantage of the enormous memory capacity of 64 bit Windows

What’s NewFull support for Windows XP and Windows Vista 64 bit editionsCapacity Meter – Display physical memory optionAutomatic installation

© 2008 Autodesk 17

Assembly Substitution

What’s NewiMate

Capacity meterPlace OrientationAngle ConstraintsDrive Constraint to Piont of

CollisionReduced Memory Mode for Derived

AssembliesCenter of GravitySubstitue Level of DetailGrip Snap

© 2008 Autodesk 18

Concept Design

Experiment with alternative design concepts before starting detailed design

What’s NewGrip Snap – Move & Rotate assembly components using geometric input

© 2008 Autodesk 19

Derive – Reduced Memory Option

Create derived assemblies that consume less memory

What’s NewNew option in Derived Assembly dialog panelSignificant memory reduction with larger derived assembliesNo solid body nodes in browser of target Part

© 2008 Autodesk 20

Studio

Add extra realism to renderings and animations

What’s NewDynamic Sim->StudioUser defined camera pathsDepth of field / f-numberVideo compositingSoft shadowsLocal lightsReposition Lighting OriginsConstraint Suppression

© 2008 Autodesk 21

Updated Navigation Controls

Single click access to orthographic and isometric views and quicker access to pan, zoom and rotate

What’s NewView Cube

On screen 3D view control with user defined home viewUse View Cube Front to define Base View in drawing sheets

Steering WheelEye-level access to 2D navigation controls

© 2008 Autodesk 22

Native Translators

Work with suppliers and customers who use native CAD file formatsMigrate data from legacy 3D systems

What’s NewNative Translators

SolidWorks Pro/E

Parasolid

PTC Granite

STEP&

IGES

UG-NX

SATJTSTL

© 2008 Autodesk 23

Sketching Productivity

Rapidly interpret design intent from Inventor sketches

What’s NewPoint Alignment(Constraint

Persistence,Inference)Scale FactorDegree of FreedomSketch Property in ModelTrim & ExtendArc TextImport pointsPoints remains

Inventor 2008

Inventor 2009

© 2008 Autodesk 24

Sketching Productivity

Rapidly interpret design intent from Inventor sketches

What’s NewSimpler representation for coincidenceNew glyph designSingle glyphs for perpendicular and tangent constraintsSelect Sketch enables Sketch Properties toolbar outside of Sketch ModeEnable Toggle Button outside Sketch Mode

Inventor 2008

Inventor 2009

© 2008 Autodesk 25

Sketching Productivity

Enjoy increased productivity when creating sketches

What’s NewText along arcs and circlesDegrees of freedom displayAutomatic tangent constraint for closed arc-line sketchesSpline through imported pointsPoint-curve coincident constraint for 3D sketch Trim/extend alternate solution

© 2008 Autodesk 26

Constraint Inference & Persistence

Easily experiment with new layouts and conceptual designs

What’s NewNew Inference and Persistence controls

No constraintsInfer constraints but no persistenceCreate persistent constraints

New inference scope controlAdditional point alignment controlQuadrant point constraints

© 2008 Autodesk 27

Sheet Metal Styles

Create parts based on material and manufacturing capabilities

What’s NewSheet Thickness integrated into Material StylesDirect bend tables editing in the Styles EditorNew Sheet Metal RulesNew Unfold Rules replaces Unfold Methods

© 2008 Autodesk 28

Interactive Flange Options

Reduce time creating and modifying flanges with custom seam and corner reliefs

What’s NewMulti-edge mitering including non-adjacent edgesNew direct edit UI to override corner seams and reliefsLarge radius bends

© 2008 Autodesk 29

Sheet Metal - iParts

Represent geometry variations and manufacturing capabilities of different suppliers

What’s NewInclude bend and unfold rules in the iPart tableControl Flat Patterns in the iParttableDrawing manager support

© 2008 Autodesk 30

Sheet Metal Fasteners

Insert PEM style sheet metal fasteners in the design

What’s NewPEM fasteners available from Content CenterAutoDrop and Bolted Connection support for PEM fasteners

© 2008 Autodesk 31

Sheet Metal - Others

Reduce the time required to create and document sheet metal parts

What’s NewNew mid-plane offset option in Contour FlangeArc weld corner relief for 2-bend cornersSupport for simple tearsNamed flat pattern orientationsBend Angle DefinitionAccess kFactor in Bend Notes

© 2008 Autodesk 32

Contents Center

Save copy as독립형

종속형

© 2008 Autodesk 33

Drawing Manager

What’s NewPart list FiltersShaded View ResolutionReorder Prompted EntriesMulti Center lineView Annotation StyleView Label & View LeaderContaint to View BorderCropInterference EdgesLinear Dimension TEXT wrapingCorner Leader Attachment Feature

control Frame

© 2008 Autodesk 34

Drawing Manager

Be more productive when creating manufacturing drawings

What’s NewCrop ViewInterference EdgesCenter of Gravity DisplayParts List FiltersReorder Prompted Entries

© 2008 Autodesk 35

Drawing Manager

Exercise precise control over annotation format

What’s NewNew Punch Note tool View configuration control with new View Annotation StyleDetail View leader linesSuperscript & SubscriptFractional dimension values

© 2008 Autodesk 36

CAPACITY

PRODUCTIVITY

PERFORMANCE

© 2008 Autodesk 37

Increasing Design Productivity

Sketch UsabilitySheet MetalNew Drawing Manager ToolsImproved Navigation Tools

© 2008 Autodesk 38

Working With Other People’s Data

Native translators

Integrate imported geometry in 3D models

Improved publishing

© 2008 Autodesk 39

Other Productivity Enhancements

Cable & Harness – Defer update optionCable & Harness – Multiple control point modification

Format control for custom iProperties

Content Center – Separate server login

Content Center – Performance improvements

Improved Help System

© 2008 Autodesk 40

Driving Innovation

Improved Design Accelerators

Simulation Workflow

User Defined Frame Sections

Self Draining Lines

Simplified Rendering Tools

© 2008 Autodesk 41

Simplified Software Administration

License ManagementIdle session timeout

Install & DeploymentImproved Installer PerformanceFull support for 32 & 64 bit deploymentsUnified Installer DocumentationCAD Manager DocumentationSmaller deployment images

© 2008 Autodesk 42

Increasing User ProductivityWorking on larger designs

Native 64 bit versionComponent substitutionPerformance optimization

Working with other people’s dataNative translators: Pro/E, Granite, UG-NX, Parasolid and SolidWorks

Enabling more innovation Easy to use simulation tools integrated with the design workflowAdvanced sheet metal with manufacturing design rulesSmart pipe runs with new support for hygienic pipe standards

© 2008 Autodesk 43