Date post: | 18-Apr-2015 |
Category: |
Documents |
Upload: | petar-uljarevic |
View: | 163 times |
Download: | 2 times |
WCDMA RAN and I-HSPA, Rel. RU30, Operating Documentation, Issue 07
IP Configuration Plan Interface Parameters
DN70257257
Issue 04FApproval Date 2011-11-25
Confidential
2 DN70257257Issue 04F
IP Configuration Plan Interface Parameters
Id:0900d805809140a9Confidential
The information in this document is subject to change without notice and describes only the product defined in the introduction of this documentation. This documentation is intended for the use of Nokia Siemens Networks customers only for the purposes of the agreement under which the document is submitted, and no part of it may be used, reproduced, modified or transmitted in any form or means without the prior written permission of Nokia Siemens Networks. The documentation has been prepared to be used by professional and properly trained personnel, and the customer assumes full responsibility when using it. Nokia Siemens Networks welcomes customer comments as part of the process of continuous development and improvement of the documentation.
The information or statements given in this documentation concerning the suitability, capacity, or performance of the mentioned hardware or software products are given "as is" and all liability arising in connection with such hardware or software products shall be defined conclusively and finally in a separate agreement between Nokia Siemens Networks and the customer. However, Nokia Siemens Networks has made all reasonable efforts to ensure that the instructions contained in the document are adequate and free of material errors and omissions. Nokia Siemens Networks will, if deemed necessary by Nokia Siemens Networks, explain issues which may not be covered by the document.
Nokia Siemens Networks will correct errors in this documentation as soon as possible. IN NO EVENT WILL Nokia Siemens Networks BE LIABLE FOR ERRORS IN THIS DOCUMENTA-TION OR FOR ANY DAMAGES, INCLUDING BUT NOT LIMITED TO SPECIAL, DIRECT, INDI-RECT, INCIDENTAL OR CONSEQUENTIAL OR ANY LOSSES, SUCH AS BUT NOT LIMITED TO LOSS OF PROFIT, REVENUE, BUSINESS INTERRUPTION, BUSINESS OPPORTUNITY OR DATA,THAT MAY ARISE FROM THE USE OF THIS DOCUMENT OR THE INFORMATION IN IT.
This documentation and the product it describes are considered protected by copyrights and other intellectual property rights according to the applicable laws.
The wave logo is a trademark of Nokia Siemens Networks Oy. Nokia is a registered trademark of Nokia Corporation. Siemens is a registered trademark of Siemens AG.
Other product names mentioned in this document may be trademarks of their respective owners, and they are mentioned for identification purposes only.
Copyright © Nokia Siemens Networks 2011. All rights reserved
f Important Notice on Product SafetyThis product may present safety risks due to laser, electricity, heat, and other sources of danger.
Only trained and qualified personnel may install, operate, maintain or otherwise handle this product and only after having carefully read the safety information applicable to this product.
The safety information is provided in the Safety Information section in the “Legal, Safety and Environmental Information” part of this document or documentation set.
The same text in German:
f Wichtiger Hinweis zur Produktsicherheit Von diesem Produkt können Gefahren durch Laser, Elektrizität, Hitzeentwicklung oder andere Gefahrenquellen ausgehen.
Installation, Betrieb, Wartung und sonstige Handhabung des Produktes darf nur durch geschultes und qualifiziertes Personal unter Beachtung der anwendbaren Sicherheits-anforderungen erfolgen.
Die Sicherheitsanforderungen finden Sie unter „Sicherheitshinweise“ im Teil „Legal, Safety and Environmental Information“ dieses Dokuments oder dieses Dokumentations-satzes.
DN70257257 3
IP Configuration Plan Interface Parameters
Id:0900d805809140a9Confidential
Table of contentsThis document has 216 pages.
1 Summary of changes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 141.1 New Parameters in . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Issue 04F141.2 Changed parameters in . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Issue 04F141.3 Removed Parameters in . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Issue 04F141.3.1 IBFP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 141.3.1.1 profileType (BFD Profile Type) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 141.3.1.2 holdupTime (Holdup Time) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 141.3.2 IPRO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 141.3.2.1 phbeBE (PHB BE) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
2 Introduction to IP configuration plan interface parameters . . . . . . . . . . 152.1 How to read parameter tables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
3 IAIF Parameters. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 173.1 atmIfId (ATM interface id) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 173.2 atmIfNetId (IP over ATM interface id) . . . . . . . . . . . . . . . . . . . . . . . . . . 183.3 encapsulationMethod (Encapsulation method) . . . . . . . . . . . . . . . . . . . 193.4 type (Type). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 193.5 usage (Usage) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 203.6 vci (VCI) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 213.7 vpi (VPI) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
4 IBFD Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 244.1 alarmEnabled (Alarm enabled flag) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 244.2 bfdEnabled (Bfd enabled flag) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 244.3 bfdId (BFD session id) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 254.4 dstIp (Destination IP address) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 264.5 ipbrId (Ip based route Id) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 274.6 profileId (Profile identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 284.7 sessionType (Session Type) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 294.8 srcIp (Source IP address) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
5 IBFP Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 315.1 desiredMinTx (Min transmission interval) . . . . . . . . . . . . . . . . . . . . . . . 315.2 detectMult (Detection multiplier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 315.3 dscp (DSCP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 325.4 profileId (IBFP identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 335.5 profileName (Multi-Hop BFD Profile Name). . . . . . . . . . . . . . . . . . . . . . 345.6 requiredMinRx (Required minimum reception interval) . . . . . . . . . . . . . 35
6 IDNS Parameters. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 376.1 cache (Resolver Cache) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 376.2 iDNSId (DNS Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 386.3 localDomain (Local domain name) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 386.4 roundRobin (Round robin) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 396.5 serverIPAddr (Server IP address list) . . . . . . . . . . . . . . . . . . . . . . . . . . 406.6 addrValue (Address value) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
4 DN70257257
IP Configuration Plan Interface Parameters
Id:0900d805809140a9Confidential
6.7 addrVer (IP address version for server IP address) . . . . . . . . . . . . . . . . 426.8 sortList (Network sortlist) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 436.9 addrValue (Address value) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 446.10 netmask (Netmask). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
7 IDSP Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 467.1 dscpProfileName (DSCP to PHB mapping ProfileName) . . . . . . . . . . . . 467.2 idspId (DSCP to PHB mapping profile Identifier) . . . . . . . . . . . . . . . . . . 477.3 profileList (Profile list) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 477.4 dscpNumber (Dscp Value) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 487.5 phb (PHB value) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
8 IEIF Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 518.1 IPV4Addr (IPv4 address list). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 518.2 addrTypeIPV4 (Address type IPv4) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 518.3 addrValueIPV4 (IP address IPv4) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 528.4 destAddrIPV4 (Destination address IPv4) . . . . . . . . . . . . . . . . . . . . . . . 538.5 netmask (Netmask). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 548.6 administrativeState (Administrative state). . . . . . . . . . . . . . . . . . . . . . . . 558.7 ethIfNetId (Ethernet Interface Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . 568.8 ifType (Interface type) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 578.9 mtu (Maximum Transfer Unit) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
9 IGIF Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 609.1 RncEthernetBw (EthernetBw) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 609.2 ethInterfaceRate (Ethernet interface rate) . . . . . . . . . . . . . . . . . . . . . . . 609.3 igifId (Ethernet Interface Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
10 IICP Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6310.1 echoReplyTmout (Timeout for echo reply re-ceiving) . . . . . . . . . . . . . . . 6310.2 echoReqPeriod (Period for echo request packet sending) . . . . . . . . . . . 6310.3 maxLostPkt (maxLostPkt) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6410.4 payloadLength (payloadLength) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6510.5 profileId (IICP identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
11 IOAM Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6811.1 InstanceID (Ethernet OAM Instance ID) . . . . . . . . . . . . . . . . . . . . . . . . . 6811.2 activeMode (Link OAM working Mode) . . . . . . . . . . . . . . . . . . . . . . . . . . 6911.3 adminState (Link OAM Administration State ) . . . . . . . . . . . . . . . . . . . 6911.4 almClrTimer (Link OAM Critical Event Alarm Clearance Timer) . . . . . . . 7011.5 efEvtThd (Link OAM Error Frame Event Threshold) . . . . . . . . . . . . . . . . 7111.6 efEvtWnd (Link OAM Error Frame Event Window). . . . . . . . . . . . . . . . . 7211.7 efSecThd (Link OAM Error Frame Seconds Threshold) . . . . . . . . . . . . . 7311.8 efSecWnd (Link OAM Error Frame Seconds Window) . . . . . . . . . . . . . . 7411.9 lostTimer (Ethernet OAM Link Timeout) . . . . . . . . . . . . . . . . . . . . . . . . . 7511.10 lpDuration (Link OAM Loopback Duration Time) . . . . . . . . . . . . . . . . . . 7611.11 lpLostTimer (Link OAM Loopback Timeout) . . . . . . . . . . . . . . . . . . . . . . 7711.12 lpPktRate (Link OAM Loopback Packet Rate) . . . . . . . . . . . . . . . . . . . . 7811.13 lpPktSize (Link OAM Loopback Packet Size ) . . . . . . . . . . . . . . . . . . . . 7911.14 pduTimer (Link OAM PDU Timer) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80
DN70257257 5
IP Configuration Plan Interface Parameters
Id:0900d805809140a9Confidential
11.15 templateID (Template ID). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81
12 IOAMT Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8312.1 almClrTimer (Link OAM Critical Event Alarm Clearance Timer) . . . . . . 8312.2 efEvtThd (Link OAM Error Frame Event Threshold) . . . . . . . . . . . . . . . 8312.3 efEvtWnd (Link OAM Error Frame Event Window) . . . . . . . . . . . . . . . . 8412.4 efSecThd (Link OAM Error Frame Seconds Threshold ) . . . . . . . . . . . . 8512.5 efSecWnd (Link OAM Error Frame Seconds Window) . . . . . . . . . . . . . 8612.6 lostTimer (Ethernet OAM Link Timeout) . . . . . . . . . . . . . . . . . . . . . . . . 8712.7 lpDuration (Link OAM Loopback Duration Time) . . . . . . . . . . . . . . . . . . 8812.8 lpLostTimer (Link OAM Loopback Timeout) . . . . . . . . . . . . . . . . . . . . . 8912.9 lpPktRate (Link OAM Loopback Packet Rate) . . . . . . . . . . . . . . . . . . . . 9012.10 lpPktSize (Link OAM Loopback Packet Size) . . . . . . . . . . . . . . . . . . . . 9012.11 pduTimer (Link OAM PDU Timer) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9112.12 templateID (Template ID). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9212.13 templateName (Ethernet OAM Template Name). . . . . . . . . . . . . . . . . . 93
13 IOPF Parameters. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9513.1 iopfId (IOPF Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9513.2 rfc1583comp (RFC1583 Compatibility) . . . . . . . . . . . . . . . . . . . . . . . . . 9513.3 routeId (Router Id) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9613.4 spfDelay (SPF Delay) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9713.5 spfHoldtime (SPF Holdtime) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98
14 IPBR Parameters. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10014.1 committedBW (Committed BW) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10014.2 committedDcnBW (Committed DCN BW). . . . . . . . . . . . . . . . . . . . . . 10014.3 committedSigBW (Committed signal BW ) . . . . . . . . . . . . . . . . . . . . . 10114.4 ifcFlag (IP IFC Flag). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10214.5 ipBasedRouteName (IP based route name) . . . . . . . . . . . . . . . . . . . . 10314.6 ipbrId (IP based route id) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10414.7 localMuxUDPPort (IP multiplexing local UDP port) . . . . . . . . . . . . . . . 10514.8 maxMuxPackets (IP multiplexing max packets). . . . . . . . . . . . . . . . . . 10614.9 ratio (Ratio ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10614.10 remoteMuxUDPPort (IP multiplexing remote UDP port) . . . . . . . . . . . 10714.11 routeBW (Route bandwidth). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10814.12 udpMuxDSCP (IP multiplexing DSCP value). . . . . . . . . . . . . . . . . . . . 10914.13 udpMuxEnabled (IP multiplexing flag) . . . . . . . . . . . . . . . . . . . . . . . . . 110
15 IPHB Parameters. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11115.1 phbId (PHB profile Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11115.2 phbProfileName (PHB profile name) . . . . . . . . . . . . . . . . . . . . . . . . . . 11215.3 profileList (PHB Profile List) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11215.4 expWeig (Exponential weight factor) . . . . . . . . . . . . . . . . . . . . . . . . . . 11315.5 length (Queue length) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11415.6 maxDrop (Max drop value) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11515.7 maxThreshold (Max threshold) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11615.8 minThreshold (Min threshold) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11715.9 phb (PHB value) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 118
6 DN70257257
IP Configuration Plan Interface Parameters
Id:0900d805809140a9Confidential
15.10 quePriority (Queue priority). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11915.11 queWeight (Queue weight) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11915.12 schedule (Queue schedule) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12015.13 vlanPri (Vlan priority). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 121
16 IPNO Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12316.1 IPForwardingIPV4 (IP Forwarding flag) . . . . . . . . . . . . . . . . . . . . . . . . 12316.2 defaultTTL (Default TTL). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12416.3 hostName (Host name). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12416.4 ipNodeId (IP Node Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12516.5 subnetsAreLocal (Subnets are local) . . . . . . . . . . . . . . . . . . . . . . . . . . 126
17 IPRO Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12817.1 ipBasedRoute (IP based route Entries) . . . . . . . . . . . . . . . . . . . . . . . . 12817.2 addrValueIPV4 (IP address ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12917.3 ipBasedRouteId (IP based route id) . . . . . . . . . . . . . . . . . . . . . . . . . . . 12917.4 phbAF1 (PHB AF1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13017.5 phbAF2 (PHB AF2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13117.6 phbAF3 (PHB AF3) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13317.7 phbAF4 (PHB AF4) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13417.8 phbEF (PHB EF) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13517.9 iproId (network interface Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13617.10 iproListMode (IP Based Route id list update mode) . . . . . . . . . . . . . . . 137
18 IPRT Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14018.1 ipRoutingTableId (IP Routing Table Identifier) . . . . . . . . . . . . . . . . . . . 14018.2 iprtListMode (IP static route list update mode) . . . . . . . . . . . . . . . . . . . 14118.3 routeEntriesIPV4 (Route Entries for IPv4) . . . . . . . . . . . . . . . . . . . . . . 14218.4 bfdId (BFD session ID) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14318.5 destIPAddrIPV4 (Destination IPv4 address) . . . . . . . . . . . . . . . . . . . . . 14418.6 gatewayIPV4 (Gateway IPv4 address) . . . . . . . . . . . . . . . . . . . . . . . . . 14518.7 netmask (Netmask). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14618.8 preference (Preference) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14718.9 routeType (Route type) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14718.10 srcIPAddrIPV4 (Source IPv4 address) . . . . . . . . . . . . . . . . . . . . . . . . . 148
19 IQOS Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15019.1 dspmProfileId (DSPM profile id) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15019.2 dspmProfileName (DSPM profile name). . . . . . . . . . . . . . . . . . . . . . . . 15019.3 iqosId (Qos interface) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15119.4 phbProfileId (PHB profile id) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15219.5 phbProfileName (PHB profile name). . . . . . . . . . . . . . . . . . . . . . . . . . . 15319.6 status (Status) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 154
20 ISBFP Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15620.1 desiredMinTx (Min transmission interval) . . . . . . . . . . . . . . . . . . . . . . . 15620.2 detectMult (Detection multiplier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15620.3 dscp (DSCP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15720.4 holdupTime (Holdup Time) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15820.5 profileId (ISBFP identifier). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 159
DN70257257 7
IP Configuration Plan Interface Parameters
Id:0900d805809140a9Confidential
20.6 profileName (Single-hop BFD Profile Name) . . . . . . . . . . . . . . . . . . . . 16020.7 requiredMinRx (Required minimum reception interval) . . . . . . . . . . . . 161
21 ISPF Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16221.1 areaId (Area Identification) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16221.2 interfaceEntries (Interface Entries) . . . . . . . . . . . . . . . . . . . . . . . . . . . 16221.3 cost (Cost) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16321.4 deadInterval (Dead Interval) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16421.5 helloInterval (Hello Interval) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16521.6 interfaceName (Interface Name) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16621.7 passive (Passive). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16721.8 password (Password) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16821.9 priority (Priority) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16921.10 type (Type). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17021.11 ispfId (ISPF Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17121.12 networkPrefixEntries (Network Prefix Entries) . . . . . . . . . . . . . . . . . . . 17121.13 maskLength (Mask Length) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17221.14 networkPrefix (Network Prefix) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17321.15 restriction (Restriction) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17421.16 networkStubEntries (Network Stub Entries). . . . . . . . . . . . . . . . . . . . . 17521.17 cost (Cost) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17621.18 stubNetwork (Stub Network) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17721.19 stubPrefixLength (stub netmask ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17721.20 routeCost (Route Cost) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17821.21 stubArea (Stub Area) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17921.22 stubbyArea (Stubby Area) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18021.23 virLinkEntries (Virtual Link Entries) . . . . . . . . . . . . . . . . . . . . . . . . . . . 18121.24 deadInterval (Dead Interval) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18221.25 helloInterval (Hello Interval) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18321.26 password (Password) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18421.27 remoteRouteId (Remote Route Id). . . . . . . . . . . . . . . . . . . . . . . . . . . . 18421.28 type (type) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 185
22 ISPRT Parameters. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18722.1 interfaceEntries (Interface Entries) . . . . . . . . . . . . . . . . . . . . . . . . . . . 18722.2 ifName (Interface Name) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18722.3 metric (Metric) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18822.4 isprtId (ISPRT identifier). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18922.5 redistAllEntries (Redistribute Entries) . . . . . . . . . . . . . . . . . . . . . . . . . 19022.6 metric (Metric) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19122.7 type (Type). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19122.8 routeEntries (Route Entries) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19222.9 destIPAddrIPV4 (DestIPAddrIPV4) . . . . . . . . . . . . . . . . . . . . . . . . . . . 19322.10 gatewayIPV4 (GatewayIPV4) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19422.11 metric (Metric) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19522.12 netmask (Netmask) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 196
23 ITRKGRP Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19723.1 trkGrpBoolVal (Network Status Tracker Group Operation Bool Value) 197
8 DN70257257
IP Configuration Plan Interface Parameters
Id:0900d805809140a9Confidential
23.2 trkGrpId (Network Status Tracker Group ID) . . . . . . . . . . . . . . . . . . . . 19823.3 trkGrpOperation (Network Status Tracker Group Operation) . . . . . . . . 19923.4 trkGrpWeightVal (Network Status Tracker Group Operation Weight Value)
20023.5 trkType (Network Status Tracker Group Type) . . . . . . . . . . . . . . . . . . . 201
24 ITRKOBJ Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20224.1 trkObjName (Network Status Tracker Object Name) . . . . . . . . . . . . . . 20224.2 trkObjWeight (Network Status Tracker Object Weight). . . . . . . . . . . . . 203
25 IUBSNT Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20425.1 IPV4MaskLength (IPV4 mask length) . . . . . . . . . . . . . . . . . . . . . . . . . . 20425.2 IPV4SubnetAddress (IPV4 subnet address). . . . . . . . . . . . . . . . . . . . . 20425.3 assocMaxRetrans (Association max retrans) . . . . . . . . . . . . . . . . . . . . 20525.4 hbInterval (HB interval) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20625.5 iubsntId (Iubsnt Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20725.6 maxInitRetrans (MaxInitRetrans) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20825.7 pathMaxRetrans (PathMaxRetrans) . . . . . . . . . . . . . . . . . . . . . . . . . . . 20925.8 rtoInitial (RTO Initial) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20925.9 rtoMax (RTO Max) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21025.10 rtoMin (RTO Min) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21125.11 sackPeriod (sackPeriod) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21225.12 validCookieLife (Valid Cookie Life) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 213
26 IVIF Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21426.1 parentInterface (Vlan physical Interface) . . . . . . . . . . . . . . . . . . . . . . . 21426.2 vid (Vlan id) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21426.3 vlanIfId (Vlan Interface Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 215
DN70257257 9
IP Configuration Plan Interface Parameters
Id:0900d805809140a9Confidential
List of tablesTable 1 How to read parameter tables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15Table 2 atmIfId (ATM interface id) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17Table 3 atmIfNetId (IP over ATM interface id) . . . . . . . . . . . . . . . . . . . . . . . . . . 18Table 4 encapsulationMethod (Encapsulation method) . . . . . . . . . . . . . . . . . . . 19Table 5 type (Type) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19Table 6 usage (Usage) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20Table 7 vci (VCI) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21Table 8 vpi (VPI) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22Table 9 alarmEnabled (Alarm enabled flag) . . . . . . . . . . . . . . . . . . . . . . . . . . . 24Table 10 bfdEnabled (Bfd enabled flag) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24Table 11 bfdId (BFD session id) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25Table 12 dstIp (Destination IP address) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26Table 13 ipbrId (Ip based route Id) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27Table 14 profileId (Profile identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28Table 15 sessionType (Session Type) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29Table 16 srcIp (Source IP address) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30Table 17 desiredMinTx (Min transmission interval) . . . . . . . . . . . . . . . . . . . . . . 31Table 18 detectMult (Detection multiplier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31Table 19 dscp (DSCP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32Table 20 profileId (IBFP identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33Table 21 profileName (Multi-Hop BFD Profile Name) . . . . . . . . . . . . . . . . . . . . . 34Table 22 requiredMinRx (Required minimum reception interval) . . . . . . . . . . . . . 35Table 23 cache (Resolver Cache) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37Table 24 iDNSId (DNS Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38Table 25 localDomain (Local domain name) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38Table 26 roundRobin (Round robin) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39Table 27 serverIPAddr (Server IP address list) . . . . . . . . . . . . . . . . . . . . . . . . . . 40Table 28 addrValue (Address value) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41Table 29 addrVer (IP address version for server IP address) . . . . . . . . . . . . . . . 42Table 30 sortList (Network sortlist) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43Table 31 addrValue (Address value) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44Table 32 netmask (Netmask) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44Table 33 dscpProfileName (DSCP to PHB mapping ProfileName) . . . . . . . . . . . 46Table 34 idspId (DSCP to PHB mapping profile Identifier) . . . . . . . . . . . . . . . . . 47Table 35 profileList (Profile list) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47Table 36 dscpNumber (Dscp Value) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48Table 37 phb (PHB value) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49Table 38 IPV4Addr (IPv4 address list) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51Table 39 addrTypeIPV4 (Address type IPv4) . . . . . . . . . . . . . . . . . . . . . . . . . . . 51Table 40 addrValueIPV4 (IP address IPv4) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52Table 41 destAddrIPV4 (Destination address IPv4) . . . . . . . . . . . . . . . . . . . . . . 53Table 42 netmask (Netmask) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54Table 43 administrativeState (Administrative state) . . . . . . . . . . . . . . . . . . . . . . . 55Table 44 ethIfNetId (Ethernet Interface Identifier) . . . . . . . . . . . . . . . . . . . . . . . . 56Table 45 ifType (Interface type) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
10 DN70257257
IP Configuration Plan Interface Parameters
Id:0900d805809140a9Confidential
Table 46 mtu (Maximum Transfer Unit) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58Table 47 RncEthernetBw (EthernetBw) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60Table 48 ethInterfaceRate (Ethernet interface rate) . . . . . . . . . . . . . . . . . . . . . . . 60Table 49 igifId (Ethernet Interface Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61Table 50 echoReplyTmout (Timeout for echo reply re-ceiving) . . . . . . . . . . . . . . 63Table 51 echoReqPeriod (Period for echo request packet sending) . . . . . . . . . . 63Table 52 maxLostPkt (maxLostPkt) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64Table 53 payloadLength (payloadLength) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65Table 54 profileId (IICP identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66Table 55 InstanceID (Ethernet OAM Instance ID) . . . . . . . . . . . . . . . . . . . . . . . . 68Table 56 activeMode (Link OAM working Mode) . . . . . . . . . . . . . . . . . . . . . . . . . 69Table 57 adminState (Link OAM Administration State ) . . . . . . . . . . . . . . . . . . . 69Table 58 almClrTimer (Link OAM Critical Event Alarm Clearance Timer) . . . . . . 70Table 59 efEvtThd (Link OAM Error Frame Event Threshold) . . . . . . . . . . . . . . . 71Table 60 efEvtWnd (Link OAM Error Frame Event Window) . . . . . . . . . . . . . . . . 72Table 61 efSecThd (Link OAM Error Frame Seconds Threshold) . . . . . . . . . . . . 73Table 62 efSecWnd (Link OAM Error Frame Seconds Window) . . . . . . . . . . . . . 74Table 63 lostTimer (Ethernet OAM Link Timeout) . . . . . . . . . . . . . . . . . . . . . . . . 75Table 64 lpDuration (Link OAM Loopback Duration Time) . . . . . . . . . . . . . . . . . . 76Table 65 lpLostTimer (Link OAM Loopback Timeout) . . . . . . . . . . . . . . . . . . . . . 77Table 66 lpPktRate (Link OAM Loopback Packet Rate) . . . . . . . . . . . . . . . . . . . . 78Table 67 lpPktSize (Link OAM Loopback Packet Size ) . . . . . . . . . . . . . . . . . . . . 79Table 68 pduTimer (Link OAM PDU Timer) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80Table 69 templateID (Template ID) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81Table 70 almClrTimer (Link OAM Critical Event Alarm Clearance Timer) . . . . . . 83Table 71 efEvtThd (Link OAM Error Frame Event Threshold) . . . . . . . . . . . . . . . 83Table 72 efEvtWnd (Link OAM Error Frame Event Window) . . . . . . . . . . . . . . . . 84Table 73 efSecThd (Link OAM Error Frame Seconds Threshold ) . . . . . . . . . . . . 85Table 74 efSecWnd (Link OAM Error Frame Seconds Window) . . . . . . . . . . . . . 86Table 75 lostTimer (Ethernet OAM Link Timeout) . . . . . . . . . . . . . . . . . . . . . . . . 87Table 76 lpDuration (Link OAM Loopback Duration Time) . . . . . . . . . . . . . . . . . . 88Table 77 lpLostTimer (Link OAM Loopback Timeout) . . . . . . . . . . . . . . . . . . . . . 89Table 78 lpPktRate (Link OAM Loopback Packet Rate) . . . . . . . . . . . . . . . . . . . . 90Table 79 lpPktSize (Link OAM Loopback Packet Size) . . . . . . . . . . . . . . . . . . . . 90Table 80 pduTimer (Link OAM PDU Timer) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91Table 81 templateID (Template ID) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92Table 82 templateName (Ethernet OAM Template Name) . . . . . . . . . . . . . . . . . . 93Table 83 iopfId (IOPF Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95Table 84 rfc1583comp (RFC1583 Compatibility) . . . . . . . . . . . . . . . . . . . . . . . . . 95Table 85 routeId (Router Id) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96Table 86 spfDelay (SPF Delay) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97Table 87 spfHoldtime (SPF Holdtime) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98Table 88 committedBW (Committed BW) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100Table 89 committedDcnBW (Committed DCN BW) . . . . . . . . . . . . . . . . . . . . . . 100Table 90 committedSigBW (Committed signal BW ) . . . . . . . . . . . . . . . . . . . . . 101Table 91 ifcFlag (IP IFC Flag) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 102Table 92 ipBasedRouteName (IP based route name) . . . . . . . . . . . . . . . . . . . . 103
DN70257257 11
IP Configuration Plan Interface Parameters
Id:0900d805809140a9Confidential
Table 93 ipbrId (IP based route id) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104Table 94 localMuxUDPPort (IP multiplexing local UDP port) . . . . . . . . . . . . . . . 105Table 95 maxMuxPackets (IP multiplexing max packets) . . . . . . . . . . . . . . . . . 106Table 96 ratio (Ratio ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106Table 97 remoteMuxUDPPort (IP multiplexing remote UDP port) . . . . . . . . . . . 107Table 98 routeBW (Route bandwidth) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108Table 99 udpMuxDSCP (IP multiplexing DSCP value) . . . . . . . . . . . . . . . . . . . 109Table 100 udpMuxEnabled (IP multiplexing flag) . . . . . . . . . . . . . . . . . . . . . . . . 110Table 101 phbId (PHB profile Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 111Table 102 phbProfileName (PHB profile name) . . . . . . . . . . . . . . . . . . . . . . . . . . 112Table 103 profileList (PHB Profile List) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 112Table 104 expWeig (Exponential weight factor) . . . . . . . . . . . . . . . . . . . . . . . . . 113Table 105 length (Queue length) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 114Table 106 maxDrop (Max drop value) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 115Table 107 maxThreshold (Max threshold) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 116Table 108 minThreshold (Min threshold) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 117Table 109 phb (PHB value) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 118Table 110 quePriority (Queue priority) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 119Table 111 queWeight (Queue weight) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 119Table 112 schedule (Queue schedule) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120Table 113 vlanPri (Vlan priority) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 121Table 114 IPForwardingIPV4 (IP Forwarding flag) . . . . . . . . . . . . . . . . . . . . . . . 123Table 115 defaultTTL (Default TTL) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 124Table 116 hostName (Host name) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 124Table 117 ipNodeId (IP Node Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125Table 118 subnetsAreLocal (Subnets are local) . . . . . . . . . . . . . . . . . . . . . . . . . 126Table 119 ipBasedRoute (IP based route Entries) . . . . . . . . . . . . . . . . . . . . . . . 128Table 120 addrValueIPV4 (IP address ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 129Table 121 ipBasedRouteId (IP based route id) . . . . . . . . . . . . . . . . . . . . . . . . . . 129Table 122 phbAF1 (PHB AF1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 130Table 123 phbAF2 (PHB AF2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 131Table 124 phbAF3 (PHB AF3) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 133Table 125 phbAF4 (PHB AF4) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 134Table 126 phbEF (PHB EF) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 135Table 127 iproId (network interface Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . 136Table 128 iproListMode (IP Based Route id list update mode) . . . . . . . . . . . . . . 137Table 129 ipRoutingTableId (IP Routing Table Identifier) . . . . . . . . . . . . . . . . . . 140Table 130 iprtListMode (IP static route list update mode) . . . . . . . . . . . . . . . . . . 141Table 131 routeEntriesIPV4 (Route Entries for IPv4) . . . . . . . . . . . . . . . . . . . . . 142Table 132 bfdId (BFD session ID) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 143Table 133 destIPAddrIPV4 (Destination IPv4 address) . . . . . . . . . . . . . . . . . . . . 144Table 134 gatewayIPV4 (Gateway IPv4 address) . . . . . . . . . . . . . . . . . . . . . . . . 145Table 135 netmask (Netmask) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 146Table 136 preference (Preference) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 147Table 137 routeType (Route type) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 147Table 138 srcIPAddrIPV4 (Source IPv4 address) . . . . . . . . . . . . . . . . . . . . . . . . 148Table 139 dspmProfileId (DSPM profile id) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 150
12 DN70257257
IP Configuration Plan Interface Parameters
Id:0900d805809140a9Confidential
Table 140 dspmProfileName (DSPM profile name) . . . . . . . . . . . . . . . . . . . . . . . 150Table 141 iqosId (Qos interface) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 151Table 142 phbProfileId (PHB profile id) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 152Table 143 phbProfileName (PHB profile name) . . . . . . . . . . . . . . . . . . . . . . . . . . 153Table 144 status (Status) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 154Table 145 desiredMinTx (Min transmission interval) . . . . . . . . . . . . . . . . . . . . . . 156Table 146 detectMult (Detection multiplier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 156Table 147 dscp (DSCP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 157Table 148 holdupTime (Holdup Time) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 158Table 149 profileId (ISBFP identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 159Table 150 profileName (Single-hop BFD Profile Name) . . . . . . . . . . . . . . . . . . . . 160Table 151 requiredMinRx (Required minimum reception interval) . . . . . . . . . . . . 161Table 152 areaId (Area Identification) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 162Table 153 interfaceEntries (Interface Entries) . . . . . . . . . . . . . . . . . . . . . . . . . . . 162Table 154 cost (Cost) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 163Table 155 deadInterval (Dead Interval) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 164Table 156 helloInterval (Hello Interval) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 165Table 157 interfaceName (Interface Name) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 166Table 158 passive (Passive) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 167Table 159 password (Password) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 168Table 160 priority (Priority) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 169Table 161 type (Type) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 170Table 162 ispfId (ISPF Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 171Table 163 networkPrefixEntries (Network Prefix Entries) . . . . . . . . . . . . . . . . . . . 171Table 164 maskLength (Mask Length) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 172Table 165 networkPrefix (Network Prefix) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 173Table 166 restriction (Restriction) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 174Table 167 networkStubEntries (Network Stub Entries) . . . . . . . . . . . . . . . . . . . . . 175Table 168 cost (Cost) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 176Table 169 stubNetwork (Stub Network) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 177Table 170 stubPrefixLength (stub netmask ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 177Table 171 routeCost (Route Cost) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 178Table 172 stubArea (Stub Area) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 179Table 173 stubbyArea (Stubby Area) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 180Table 174 virLinkEntries (Virtual Link Entries) . . . . . . . . . . . . . . . . . . . . . . . . . . . 181Table 175 deadInterval (Dead Interval) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 182Table 176 helloInterval (Hello Interval) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 183Table 177 password (Password) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 184Table 178 remoteRouteId (Remote Route Id) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 184Table 179 type (type) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 185Table 180 interfaceEntries (Interface Entries) . . . . . . . . . . . . . . . . . . . . . . . . . . . 187Table 181 ifName (Interface Name) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 187Table 182 metric (Metric) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 188Table 183 isprtId (ISPRT identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 189Table 184 redistAllEntries (Redistribute Entries) . . . . . . . . . . . . . . . . . . . . . . . . . 190Table 185 metric (Metric) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 191Table 186 type (Type) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 191
DN70257257 13
IP Configuration Plan Interface Parameters
Id:0900d805809140a9Confidential
Table 187 routeEntries (Route Entries) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 192Table 188 destIPAddrIPV4 (DestIPAddrIPV4) . . . . . . . . . . . . . . . . . . . . . . . . . . . 193Table 189 gatewayIPV4 (GatewayIPV4) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 194Table 190 metric (Metric) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 195Table 191 netmask (Netmask) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 196Table 192 trkGrpBoolVal (Network Status Tracker Group Operation Bool Value) 197Table 193 trkGrpId (Network Status Tracker Group ID) . . . . . . . . . . . . . . . . . . . 198Table 194 trkGrpOperation (Network Status Tracker Group Operation) . . . . . . . 199Table 195 trkGrpWeightVal (Network Status Tracker Group Operation Weight Value)
200Table 196 trkType (Network Status Tracker Group Type) . . . . . . . . . . . . . . . . . . 201Table 197 trkObjName (Network Status Tracker Object Name) . . . . . . . . . . . . . 202Table 198 trkObjWeight (Network Status Tracker Object Weight) . . . . . . . . . . . . 203Table 199 IPV4MaskLength (IPV4 mask length) . . . . . . . . . . . . . . . . . . . . . . . . . 204Table 200 IPV4SubnetAddress (IPV4 subnet address) . . . . . . . . . . . . . . . . . . . . 204Table 201 assocMaxRetrans (Association max retrans) . . . . . . . . . . . . . . . . . . . 205Table 202 hbInterval (HB interval) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 206Table 203 iubsntId (Iubsnt Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 207Table 204 maxInitRetrans (MaxInitRetrans) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 208Table 205 pathMaxRetrans (PathMaxRetrans) . . . . . . . . . . . . . . . . . . . . . . . . . . 209Table 206 rtoInitial (RTO Initial) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 209Table 207 rtoMax (RTO Max) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 210Table 208 rtoMin (RTO Min) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 211Table 209 sackPeriod (sackPeriod) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 212Table 210 validCookieLife (Valid Cookie Life) . . . . . . . . . . . . . . . . . . . . . . . . . . . 213Table 211 parentInterface (Vlan physical Interface) . . . . . . . . . . . . . . . . . . . . . . 214Table 212 vid (Vlan id) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 214Table 213 vlanIfId (Vlan Interface Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 215
14 DN70257257
IP Configuration Plan Interface Parameters
Id:0900d805808e2b75Confidential
Summary of changes
1 Summary of changesChanges between document issues are cumulative. Therefore, the latest document issue contains all changes made to previous issues.
Changes between Issue 04E (2011-09-16, RU30) and Issue 04F (2011-11-25, RU30).
1.1 New Parameters in Issue 04FThere are no new parameters.
1.2 Changed parameters in Issue 04FThere are no changed parameters.
1.3 Removed Parameters in Issue 04F
1.3.1 IBFP
1.3.1.1 profileType (BFD Profile Type)
1.3.1.2 holdupTime (Holdup Time)
1.3.2 IPRO
1.3.2.1 phbeBE (PHB BE)
DN70257257 15
IP Configuration Plan Interface Parameters Introduction to IP configuration plan interface parame-ters
Id:0900d805808e2b75Confidential
2 Introduction to IP configuration plan inter-face parametersThe purpose of this document is to assist RNC and NetAct users to find IP configuration plan interface parameters, their meanings, specifications, and default values. The managed objects and parameters are represented in an alphabetical order.
The plan-based RNC IP configuration feature introduces the configuration management interface between the RNC and NetAct. The object model and the attributes applied in the plan interface follow the generic NWI3 presentation that is also used in other Nokia Siemens Networks RAN network elements.
2.1 How to read parameter tables
Entry Description
Parameter name The user interface name for the parameter
Abbreviated name The parameter name used in XML and CSV plan files
3GPP name The used parameter name in 3GPP specifications
Managed object The object for which the parameter is defined
Parameter group The functional group which the parameter belongs to
Category The parameters are classified into the following categories:
• Operation and Maintenance • Performance Management • Radio Resource Utilisation • Telecom • Transmission
Multiplicity The multiplicity of the parameter
Description Describes the purpose of the parameter and sometimes includes extra information on the parameter
Range The user interface value range for the parameter
Step The value by which the parameter value increases or decreases within the range
Unit The measurement unit in use for the range and step, for example,
s (seconds), min (minutes), h (hour), m (meters), km (kilometers),
dBm (decibelmeter), dB (decibel), bits (bit per second),
kbit/s (kilobits per second), % (percent), per mil (per mille), period;
if no unit indicator is given, it means that the value range has no measurement unit or the parameter has no step
Formula for getting internal value
The formula for calculating the system internal value which is used within the system
Default value Nokia Siemens Networks specified default value
Table 1 How to read parameter tables
16 DN70257257
IP Configuration Plan Interface Parameters
Id:0900d805808e2b75Confidential
Introduction to IP configuration plan interface parame-ters
Default value notes Additional information (if any) on the default value
Related functions Radio-network-related functions (in addition to the main function) of the parameter
System information Accurate System information block which parameters send to a mobile
Modification Requires object locking =The managed object must be locked by the user before the modification is possible.
Not modifiable =The parameter value can be modified only through recreation of the managed object.
Online = The parameter value can be changed without any disturbance to ongoing calls
Related parameters Other parameters that affect the parameter
Parameter relationship Dependencies between the parameter and the related parameters
Related features Features associated with the parameter
Interface Information on which interfaces the parameter is transferred
References References (if any) to 3GPP specifications
Entry Description
Table 1 How to read parameter tables (Cont.)
DN70257257 17
IP Configuration Plan Interface Parameters IAIF Parameters
Id:0900d805808e2b75Confidential
3 IAIF Parameters
3.1 atmIfId (ATM interface id)
Parameter name ATM interface id
Abbreviated name atmIfId
3GPP name -
Managed Object IAIF
Parameter group -
Classification -
Multiplicity 1
Description This parameter identifies the associated ATM interface. The whole triplet ATM if, VPI, VCI needs to be given.
The related ATM layer object in RNC MML: VCLtp (ZLC)
The related ATM plan managed object: TCTT
The corresponding MML command group: ZQM, "ATM interface".
Range 1... 588
Step 1
Units -
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes Default value is not possible
Related functions -
Modification Not modifiable
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • RNC <-> RAC • RAC <-> RACApp
References -
Table 2 atmIfId (ATM interface id)
18 DN70257257
IP Configuration Plan Interface Parameters
Id:0900d805808e2b75Confidential
IAIF Parameters
3.2 atmIfNetId (IP over ATM interface id)
Parameter name IP over ATM interface id
Abbreviated name atmIfNetId
3GPP name -
Managed Object IAIF
Parameter group -
Classification -
Multiplicity 1
Description This parameter identifies the IP over ATM interface
in the system.
For OMU and GTPU, the interface id is AA0-AA511.
For ICSU, the interface id is AA0-AA449.
For NPS1(P), the interface id is IFAE0-IFAE1399.
The identifier is part of the distinguished
name and is formed in the following way:
NE-x/IPNO-unitType-unitIndex/IAIF-ifName. For
example: RNC-1/IPNO-OMU-0/IAIF-AA0.
The corresponding MML command: ZQMF,"IP interface".
Range 1...32
Step -
Units characters
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes Default value is not possible
Related functions -
Modification Not modifiable
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • RNC <-> RAC • RAC <-> RACApp
References -
Table 3 atmIfNetId (IP over ATM interface id)
DN70257257 19
IP Configuration Plan Interface Parameters IAIF Parameters
Id:0900d805808e2b75Confidential
3.3 encapsulationMethod (Encapsulation method)
3.4 type (Type)
Parameter name Encapsulation method
Abbreviated name encapsulationMethod
3GPP name -
Managed Object IAIF
Parameter group -
Classification -
Multiplicity 1
Description This parameter identifies the encapsulation method. The value is either LLC/SNAP or VCMUX.
The corresponding MML command group: ZQM, "encapsulation method".
Range LLC/SNAP (0), VCMUX (1)
Step -
Units -
Formula for getting internal value
gui ==> internal
LLC/SNAP ==> 0
VCMUX ==> 1
Default value LLC/SNAP (0)
Default value notes -
Related functions -
Modification Not modifiable
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • RNC <-> RAC • RAC <-> RACApp
References -
Table 4 encapsulationMethod (Encapsulation method)
Parameter name Type
Abbreviated name type
3GPP name -
Table 5 type (Type)
20 DN70257257
IP Configuration Plan Interface Parameters
Id:0900d805808e2b75Confidential
IAIF Parameters
3.5 usage (Usage)
Managed Object IAIF
Parameter group -
Classification -
Multiplicity 1
Description This parameter defines whether IPoA is terminated to the logical or physical address type of the unit. The possible parameter value is "L" for logical address type only.
The corresponding MML command group: ZQM, "interface type".
Range Logical (1)
Step -
Units -
Formula for getting internal value
gui ==> internal
Logical ==> 1
Default value Logical (1)
Default value notes -
Related functions -
Modification Not modifiable
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • RNC <-> RAC • RAC <-> RACApp
References -
Table 5 type (Type) (Cont.)
Parameter name Usage
Abbreviated name usage
3GPP name -
Managed Object IAIF
Parameter group -
Classification -
Multiplicity 1
Table 6 usage (Usage)
DN70257257 21
IP Configuration Plan Interface Parameters IAIF Parameters
Id:0900d805808e2b75Confidential
3.6 vci (VCI)
Description This parameter identifies the usage of the connection.
The value can be IPOAUD, IPOART,IPOAM,or IPCONN . This parameter identifies the usage of connection. The value can be IPOAUD, or IPOAM
for OMU, RSMU, ICSU and GTPU units, and the default value is IPOAM. For NPS1(P)
units, the value is IPCONN.
Note:
The value IPOART is available only if the feature
'Streaming packet switched QoS' is in use, otherwise
it is restricted.
The corresponding MML command group: ZQM,
"usage".
Range IPOAUD (0), IPOART (1), IPOAM (2), IPCONN (3)
Step -
Units -
Formula for getting internal value
gui ==> internal
IPOAUD ==> 0
IPOART ==> 1
IPOAM ==> 2
IPCONN ==> 3
Default value -
Default value notes IPCONN (3) is for NPS1(P),and IPOAM (2) is for other units.
Related functions -
Modification Not modifiable
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • RNC <-> RAC • RAC <-> RACApp
References -
Table 6 usage (Usage) (Cont.)
Parameter name VCI
Abbreviated name vci
Table 7 vci (VCI)
22 DN70257257
IP Configuration Plan Interface Parameters
Id:0900d805808e2b75Confidential
IAIF Parameters
3.7 vpi (VPI)
3GPP name -
Managed Object IAIF
Parameter group -
Classification -
Multiplicity 1
Description This parameter identifies the associated VCI within the VPI. The whole triplet ATM if, VPI, VCI needs to be given.
The related ATM layer object in RNC MML: VCLtp (ZLC command group).
The related ATM plan managed object: VCCT object id.
The corresponding MML command group: ZQM, "VCI number".
Range 1... 65535
Step 1
Units -
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes Default value is not possible
Related functions -
Modification Not modifiable
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • RNC <-> RAC • RAC <-> RACApp
References -
Table 7 vci (VCI) (Cont.)
Parameter name VPI
Abbreviated name vpi
3GPP name -
Managed Object IAIF
Parameter group -
Classification -
Table 8 vpi (VPI)
DN70257257 23
IP Configuration Plan Interface Parameters IAIF Parameters
Id:0900d805808e2b75Confidential
Multiplicity 1
Description This parameter identifies the associated VPI within the ATM interface. The whole triplet ATM if, VPI, VCI needs to be given.
The related ATM layer object in RNC MML: VPLtp (ZLC command group).
The related ATM plan managed object: VPTT object id.
The corresponding MML command group: ZQM, "VPI number".
Range 0... 4095
Step 1
Units -
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes Default value is not possible
Related functions -
Modification Not modifiable
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • RNC <-> RAC • RAC <-> RACApp
References -
Table 8 vpi (VPI) (Cont.)
24 DN70257257
IP Configuration Plan Interface Parameters
Id:0900d805808e2b75Confidential
IBFD Parameters
4 IBFD Parameters
4.1 alarmEnabled (Alarm enabled flag)
4.2 bfdEnabled (Bfd enabled flag)
Parameter name Alarm enabled flag
Abbreviated name alarmEnabled
3GPP name -
Managed Object IBFD
Parameter group -
Classification -
Multiplicity 1
Description This parameter defines whether alarm reporting per BFD session is enabled or dis-abled.
The corresponding MML command group: ZYGS,"alarm".
Range Disable (0), Enable (1)
Step -
Units -
Formula for getting internal value
gui ==> internal
Disable ==> 0
Enable ==> 1
Default value Enable (1)
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • RNC <-> RAC • RAC <-> RACApp
References -
Table 9 alarmEnabled (Alarm enabled flag)
Parameter name Bfd enabled flag
Table 10 bfdEnabled (Bfd enabled flag)
DN70257257 25
IP Configuration Plan Interface Parameters IBFD Parameters
Id:0900d805808e2b75Confidential
4.3 bfdId (BFD session id)
Abbreviated name bfdEnabled
3GPP name -
Managed Object IBFD
Parameter group -
Classification -
Multiplicity 1
Description This parameter defines whether a BFD session is enabled or disabled. If it is dis-abled, the session remains in the "AdminDown" state until it is enabled again. It must be enabled for the Create operation if it exists in the download file.
The corresponding MML command group: ZYGS, "mode".
Range Disable (0), Enable (1)
Step -
Units -
Formula for getting internal value
gui ==> internal
Disable ==> 0
Enable ==> 1
Default value Enable (1)
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • RNC <-> RAC • RAC <-> RACApp
References -
Table 10 bfdEnabled (Bfd enabled flag) (Cont.)
Parameter name BFD session id
Abbreviated name bfdId
3GPP name -
Managed Object IBFD
Parameter group -
Table 11 bfdId (BFD session id)
26 DN70257257
IP Configuration Plan Interface Parameters
Id:0900d805808e2b75Confidential
IBFD Parameters
4.4 dstIp (Destination IP address)
Classification -
Multiplicity 1
Description This parameter identifies the BFD session in the system. The identifier is part of the distinguished name and is formed in the following way: NE-x/IPNO-unitType-unit-Index/IBFD-bfdId. For example: RNC-02/IPNO-NPGEP-0/IBFD-1.
The corresponding MML command group: ZYGS,"session id".
Range 1... 3000
Step 1
Units -
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes -
Related functions -
Modification Not modifiable
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • RNC <-> RAC • RAC <-> RACApp
References -
Table 11 bfdId (BFD session id) (Cont.)
Parameter name Destination IP address
Abbreviated name dstIp
3GPP name -
Managed Object IBFD
Parameter group -
Classification -
Multiplicity 1
Description This parameter defines the destination IP address used for the BFD session. The address is specified in the conventional dot notation (#.#.#.#).
The corresponding MML command group: ZYGS,"remote IP address".
Range 7...15
Table 12 dstIp (Destination IP address)
DN70257257 27
IP Configuration Plan Interface Parameters IBFD Parameters
Id:0900d805808e2b75Confidential
4.5 ipbrId (Ip based route Id)
Step -
Units characters
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes default value is not possible
Related functions -
Modification Not modifiable
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • RAC <-> RNC • RAC <-> RACApp
References -
Table 12 dstIp (Destination IP address) (Cont.)
Parameter name Ip based route Id
Abbreviated name ipbrId
3GPP name -
Managed Object IBFD
Parameter group -
Classification -
Multiplicity 1
Description This parameter identifies the IP based route to which the operator wants to asso-ciate the BFD session. The association is not mandatory but is needed to allow HSPA Transport Fallback basing on the BFD session status.
Range 0... 4095
Step 1
Units -
Formula for getting internal value
internal_value = gui_value
Default value 0
Default value notes 0 means undefined (no associated IPBR)
Table 13 ipbrId (Ip based route Id)
28 DN70257257
IP Configuration Plan Interface Parameters
Id:0900d805808e2b75Confidential
IBFD Parameters
4.6 profileId (Profile identifier)
Related functions -
Modification Not modifiable
Related parameters ipbrId of IPBR - The IP Based route must be created firstly.
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • RNC <-> RAC • RAC <-> RACApp
References -
Table 13 ipbrId (Ip based route Id) (Cont.)
Parameter name Profile identifier
Abbreviated name profileId
3GPP name -
Managed Object IBFD
Parameter group -
Classification -
Multiplicity 1
Description The profile identifier parameter is used to associate a BFD session to an existing BFD profile. The corresponding MML command group: ZYGS, "profile id".
Range 0... 7
Step 1
Units -
Formula for getting internal value
internal_value = gui_value
Default value 0
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Table 14 profileId (Profile identifier)
DN70257257 29
IP Configuration Plan Interface Parameters IBFD Parameters
Id:0900d805808e2b75Confidential
4.7 sessionType (Session Type)
Interfaces • RNC <-> RAC • RAC <-> RACApp
References -
Table 14 profileId (Profile identifier) (Cont.)
Parameter name Session Type
Abbreviated name sessionType
3GPP name -
Managed Object IBFD
Parameter group -
Classification -
Multiplicity 1
Description The parameter defines the type of the BFD session. It can set values 0(BFD Multi-Hop Session), 1(ICMP Session) and 2(BFD Single-Hop Session).
The corresponding MML command:ZYGS
Range BFD MULTI-HOP (0), ICMP (1), BFD SINGLE-HOP (2)
Step -
Units -
Formula for getting internal value
gui ==> internal
BFD MULTI-HOP ==> 0
ICMP ==> 1
BFD SINGLE-HOP ==> 2
Default value BFD MULTI-HOP (0)
Default value notes -
Related functions -
Modification Not modifiable
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • RNC <-> RAC • RAC <-> RACApp
References -
Table 15 sessionType (Session Type)
30 DN70257257
IP Configuration Plan Interface Parameters
Id:0900d805808e2b75Confidential
IBFD Parameters
4.8 srcIp (Source IP address)
Parameter name Source IP address
Abbreviated name srcIp
3GPP name -
Managed Object IBFD
Parameter group -
Classification -
Multiplicity 1
Description This parameter defines the source IP address used for the BFD session. The address is specified in the conventional dot notation (#.#.#.#).
The corresponding MML command group: ZYGS,"local IP address".
Range 7...15
Step -
Units characters
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes Default vlaue is not possible
Related functions -
Modification Not modifiable
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • RNC <-> RAC • RAC <-> RACApp
References -
Table 16 srcIp (Source IP address)
DN70257257 31
IP Configuration Plan Interface Parameters IBFP Parameters
Id:0900d805808e2b75Confidential
5 IBFP Parameters
5.1 desiredMinTx (Min transmission interval)
5.2 detectMult (Detection multiplier)
Parameter name Min transmission interval
Abbreviated name desiredMinTx
3GPP name -
Managed Object IBFP
Parameter group -
Classification -
Multiplicity 1
Description This parameter defines the minimum interval between two transmitted control packets.
The corresponding MML command group:
For MHOP sessions, ZYGR,"minimum TX interval".
Range 500... 5000
Step 500
Units milliseconds
Formula for getting internal value
internal_value = gui_value
Default value 500
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • RAC <-> RNC • RACApp <-> RAC
References -
Table 17 desiredMinTx (Min transmission interval)
Parameter name Detection multiplier
Table 18 detectMult (Detection multiplier)
32 DN70257257
IP Configuration Plan Interface Parameters
Id:0900d805808e2b75Confidential
IBFP Parameters
5.3 dscp (DSCP)
Abbreviated name detectMult
3GPP name -
Managed Object IBFP
Parameter group -
Classification -
Multiplicity 1
Description This parameter indicates the number of control packets that the RNC will lose
before the BFD session is declared down.
The corresponding MML command group: ZYGR, "detect multi".
Range 2... 10
Step 1
Units -
Formula for getting internal value
internal_value = gui_value
Default value 5
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • RAC <-> RNC • RACApp <-> RAC
References -
Table 18 detectMult (Detection multiplier) (Cont.)
Parameter name DSCP
Abbreviated name dscp
3GPP name -
Managed Object IBFP
Parameter group -
Classification -
Multiplicity 1
Table 19 dscp (DSCP)
DN70257257 33
IP Configuration Plan Interface Parameters IBFP Parameters
Id:0900d805808e2b75Confidential
5.4 profileId (IBFP identifier)
Description This parameter defines the DSCP value.
The corresponding MML command: ZYGR.
Range 0... 63
Step 1
Units -
Formula for getting internal value
internal_value = gui_value
Default value 34
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • RNC <-> RAC • RAC <-> RACApp
References -
Table 19 dscp (DSCP) (Cont.)
Parameter name IBFP identifier
Abbreviated name profileId
3GPP name -
Managed Object IBFP
Parameter group -
Classification -
Multiplicity 1
Description This parameter defines the Multi-hop BFD profile in the system.
The default profile with the profile id "0" cannot be udpated or deleted.
It exists only in the upload file and is returned for planning purposes.
The identifier is part of
the distinguished name and it is formed in the following way: NE-x/IBFP-profileId. For example: RNC-02/IBFP-1.
The corresponding MML command group: ZYGR, "profile id".
Table 20 profileId (IBFP identifier)
34 DN70257257
IP Configuration Plan Interface Parameters
Id:0900d805808e2b75Confidential
IBFP Parameters
5.5 profileName (Multi-Hop BFD Profile Name)
Range 0... 7
Step 1
Units -
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes -
Related functions -
Modification Not modifiable
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • RAC <-> RNC • RAC <-> RACApp
References -
Table 20 profileId (IBFP identifier) (Cont.)
Parameter name Multi-Hop BFD Profile Name
Abbreviated name profileName
3GPP name -
Managed Object IBFP
Parameter group -
Classification -
Multiplicity 1
Description This parameter defines the name of the BFD profile.
The different profiles can use the same name.
MML command ZYGR is used in the Multi-Hop profile.
Range 1...10
Step -
Units characters
Formula for getting internal value
internal_value = gui_value
Default value UNDEFINED
Table 21 profileName (Multi-Hop BFD Profile Name)
DN70257257 35
IP Configuration Plan Interface Parameters IBFP Parameters
Id:0900d805808e2b75Confidential
5.6 requiredMinRx (Required minimum reception interval)
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • RNC <-> RAC • RAC <-> RACApp
References -
Table 21 profileName (Multi-Hop BFD Profile Name) (Cont.)
Parameter name Required minimum reception interval
Abbreviated name requiredMinRx
3GPP name -
Managed Object IBFP
Parameter group -
Classification -
Multiplicity 1
Description This parameter defines the minimum required interval between two received control packets.
The corresponding MML command group:
For MHOP sessions, ZYGR,"minimum RX interval".
Range 500... 5000
Step 500
Units milliseconds
Formula for getting internal value
internal_value = gui_value
Default value 500
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Table 22 requiredMinRx (Required minimum reception interval)
36 DN70257257
IP Configuration Plan Interface Parameters
Id:0900d805808e2b75Confidential
IBFP Parameters
Related options -
Feature dependencies -
Interfaces • RAC <-> RNC • RACApp <-> RAC
References -
Table 22 requiredMinRx (Required minimum reception interval) (Cont.)
DN70257257 37
IP Configuration Plan Interface Parameters IDNS Parameters
Id:0900d805808e2b75Confidential
6 IDNS Parameters
6.1 cache (Resolver Cache)
Parameter name Resolver Cache
Abbreviated name cache
3GPP name -
Managed Object IDNS
Parameter group -
Classification -
Multiplicity 1
Description This parameter defines whether the cache is in use or not. If the parameter is given for the first time, the default value is "YES", otherwise the default value is the current value. The possible values to the parameter are:
YES = The resolver cache is in use.
NO = The resolver cache is not in use.
The corresponding MML command group: ZQRK, "resolver cache".
Range No (0), Yes (1)
Step -
Units -
Formula for getting internal value
gui ==> internal
No ==> 0
Yes ==> 1
Default value Yes (1)
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • RNC <-> RAC • RAC <-> RACApp
References -
Table 23 cache (Resolver Cache)
38 DN70257257
IP Configuration Plan Interface Parameters
Id:0900d805808e2b75Confidential
IDNS Parameters
6.2 iDNSId (DNS Identifier)
6.3 localDomain (Local domain name)
Parameter name DNS Identifier
Abbreviated name iDNSId
3GPP name -
Managed Object IDNS
Parameter group -
Classification -
Multiplicity 1
Description This parameter identifies the DNS entity related to the IPNO in the system. There is only one IDNS within the IPNO. The identifier is part of the distinguished name and it is formed in the following way: NE-x/IPNO-unitType-unitIndex/IDNS-1. For example: RNC-1/IPNO-OMU-0/IDNS-1.
The corresponding MML command group: ZQRK.
Range 1... 1
Step 1
Units -
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes -
Related functions -
Modification Not modifiable
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • RNC <-> RAC • RAC <-> RACApp
References -
Table 24 iDNSId (DNS Identifier)
Parameter name Local domain name
Abbreviated name localDomain
3GPP name -
Table 25 localDomain (Local domain name)
DN70257257 39
IP Configuration Plan Interface Parameters IDNS Parameters
Id:0900d805808e2b75Confidential
6.4 roundRobin (Round robin)
Managed Object IDNS
Parameter group -
Classification -
Multiplicity 1
Description The local domain name as a character string. The maximum length of the name is 100 characters. If you enter a full stop (".") as the value, no domain name is used. The default value is the current value.
The corresponding MML command group: ZQRK, "local domain name".
Range 1...100
Step -
Units characters
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • RNC <-> RAC • RAC <-> RACApp
References -
Table 25 localDomain (Local domain name) (Cont.)
Parameter name Round robin
Abbreviated name roundRobin
3GPP name -
Managed Object IDNS
Parameter group -
Classification -
Multiplicity 1
Table 26 roundRobin (Round robin)
40 DN70257257
IP Configuration Plan Interface Parameters
Id:0900d805808e2b75Confidential
IDNS Parameters
6.5 serverIPAddr (Server IP address list)
Description This parameter defines whether the round robin is in use or not. If the parameter is given for the first time, the default value is "YES", otherwise the default value is the current value. The possible values to the parameter are:
YES = The round robin is in use.
NO = The round robin is not in use.
The corresponding MML command group: ZQRK, "round robin".
Range No (0), Yes (1)
Step -
Units -
Formula for getting internal value
gui ==> internal
No ==> 0
Yes ==> 1
Default value Yes (1)
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • RNC <-> RAC • RAC <-> RACApp
References -
Table 26 roundRobin (Round robin) (Cont.)
Parameter name Server IP address list
Abbreviated name serverIPAddr
3GPP name -
Managed Object IDNS
Parameter group -
Classification -
Multiplicity 3
Description Server IP address list. The corresponding MML command group: ZQRK, "pri-mary/secondary/third DNS server".
Table 27 serverIPAddr (Server IP address list)
DN70257257 41
IP Configuration Plan Interface Parameters IDNS Parameters
Id:0900d805808e2b75Confidential
6.6 addrValue (Address value)
Formula for getting internal value
-
Default value -
Default value notes -
Related functions -
Child parameters • addrValue • addrVer
Modification On-Line
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • RNC <-> RAC • RAC <-> RACApp
References -
Table 27 serverIPAddr (Server IP address list) (Cont.)
Parameter name Address value
Abbreviated name addrValue
3GPP name -
Managed Object -
Parameter group -
Classification -
Multiplicity 1
Description The IP address of the server. The address is specified in the conventional dot notation (#.#.#.#).
The corresponding MML command group: ZQRK, "primary/secondary/third DNS server".
Range 7...39
Step -
Units characters
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes -
Table 28 addrValue (Address value)
42 DN70257257
IP Configuration Plan Interface Parameters
Id:0900d805808e2b75Confidential
IDNS Parameters
6.7 addrVer (IP address version for server IP address)
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • RNC <-> RAC • RAC <-> RACApp
References -
Table 28 addrValue (Address value) (Cont.)
Parameter name IP address version for server IP address
Abbreviated name addrVer
3GPP name -
Managed Object -
Parameter group -
Classification -
Multiplicity 1
Description The IP address version for the server IP address. The corresponding MML command: ZQRK, "primary/secondary/third DNS server".
Range IPV4 (0)
Step -
Units -
Formula for getting internal value
gui ==> internal
IPV4 ==> 0
Default value IPV4 (0)
Default value notes -
Related functions -
Modification Not modifiable
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Table 29 addrVer (IP address version for server IP address)
DN70257257 43
IP Configuration Plan Interface Parameters IDNS Parameters
Id:0900d805808e2b75Confidential
6.8 sortList (Network sortlist)
Interfaces • RNC <-> RAC • RAC <-> RACApp
References -
Table 29 addrVer (IP address version for server IP address) (Cont.)
Parameter name Network sortlist
Abbreviated name sortList
3GPP name -
Managed Object IDNS
Parameter group -
Classification -
Multiplicity 10
Description The IP address of the sortlist. The address is specified in the conventional dot notation (#.#.#.#).
If you enter "0.0.0.0" as the value, there is no sortlist. The default value is the current value.
The corresponding MML command group: ZQRK, "sortlist".
Formula for getting internal value
-
Default value -
Default value notes -
Related functions -
Child parameters • addrValue • netmask
Modification On-Line
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • RNC <-> RAC • RAC <-> RACApp
References -
Table 30 sortList (Network sortlist)
44 DN70257257
IP Configuration Plan Interface Parameters
Id:0900d805808e2b75Confidential
IDNS Parameters
6.9 addrValue (Address value)
6.10 netmask (Netmask)
Parameter name Address value
Abbreviated name addrValue
3GPP name -
Managed Object -
Parameter group -
Classification -
Multiplicity 1
Description The IP address of the sortlist. The address is specified in the conventional dot notation (#.#.#.#).
If you enter '0.0.0.0' as the value, there is no sortlist. The default value is the current value.
The corresponding MML command group: ZQRK, "sortlist".
Range 7...39
Step -
Units characters
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • RNC <-> RAC • RAC <-> RACApp
References -
Table 31 addrValue (Address value)
Parameter name Netmask
Abbreviated name netmask
3GPP name -
Table 32 netmask (Netmask)
DN70257257 45
IP Configuration Plan Interface Parameters IDNS Parameters
Id:0900d805808e2b75Confidential
Managed Object -
Parameter group -
Classification -
Multiplicity 1
Description Netmask for the sortlist address.
The corresponding MML command: ZQRK, "sortlist".
Range 7...39
Step -
Units characters
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • RNC <-> RAC • RAC <-> RACApp
References -
Table 32 netmask (Netmask) (Cont.)
46 DN70257257
IP Configuration Plan Interface Parameters
Id:0900d805808e2b75Confidential
IDSP Parameters
7 IDSP Parameters
7.1 dscpProfileName (DSCP to PHB mapping ProfileName)
Parameter name DSCP to PHB mapping ProfileName
Abbreviated name dscpProfileName
3GPP name -
Managed Object IDSP
Parameter group -
Classification -
Multiplicity 1
Description This parameter defines the DSCP to PHB mapping profile name.
The profile name 'DEFAULT' is the default profile and it cannot be updated or deleted. It exists only in the upload file for planning purposes.
The profile name is unique in the RNC.
The corresponding MML command group: ZQ8B, "profile name".
Range 1...20
Step -
Units characters
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • RNC <-> RAC • RAC <-> RACApp
References -
Table 33 dscpProfileName (DSCP to PHB mapping ProfileName)
DN70257257 47
IP Configuration Plan Interface Parameters IDSP Parameters
Id:0900d805808e2b75Confidential
7.2 idspId (DSCP to PHB mapping profile Identifier)
7.3 profileList (Profile list)
Parameter name DSCP to PHB mapping profile Identifier
Abbreviated name idspId
3GPP name -
Managed Object IDSP
Parameter group -
Classification -
Multiplicity 1
Description This parameter identifies the DSCP to PHB mapping profile in the system.
The profile id 0 is the default profile and it cannot be updated or deleted. It exists only in the upload file for planning purposes.
The profile id is unique in the RNC.
The identifier is part of the distinguished name and it is formed in the following way:
NE-x/IDSP-dspId. For example: RNC-1/IDSP-1.
The corresponding MML command group: ZQ8B, "profile id".
Range 0... 10
Step 1
Units -
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes -
Related functions -
Modification Not modifiable
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • RNC <-> RAC • RAC <-> RACApp
References -
Table 34 idspId (DSCP to PHB mapping profile Identifier)
Parameter name Profile list
Table 35 profileList (Profile list)
48 DN70257257
IP Configuration Plan Interface Parameters
Id:0900d805808e2b75Confidential
IDSP Parameters
7.4 dscpNumber (Dscp Value)
Abbreviated name profileList
3GPP name -
Managed Object IDSP
Parameter group -
Classification -
Multiplicity 64
Description This parameter defines the DSCP to the PHB mapping profile.
There is one default profile for mapping the DSCP to PHB.
When you create another profile, you can input only some mapping items other than 64; for others, the mapping relationship in the default profile is used.
Formula for getting internal value
-
Default value -
Default value notes -
Related functions -
Child parameters • dscpNumber • phb
Modification On-Line
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • RNC <-> RAC • RAC <-> RACApp
References -
Table 35 profileList (Profile list) (Cont.)
Parameter name Dscp Value
Abbreviated name dscpNumber
3GPP name -
Managed Object -
Parameter group -
Classification -
Multiplicity 1
Table 36 dscpNumber (Dscp Value)
DN70257257 49
IP Configuration Plan Interface Parameters IDSP Parameters
Id:0900d805808e2b75Confidential
7.5 phb (PHB value)
Description This parameter defines the DSCP value which is used for mapping the PHB value.
The corresponding MML command group: ZQ8B.
Range 0... 63
Step 1
Units -
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes Default value is not possible
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • RNC <-> RAC • RAC <-> RACApp
References -
Table 36 dscpNumber (Dscp Value) (Cont.)
Parameter name PHB value
Abbreviated name phb
3GPP name -
Managed Object -
Parameter group -
Classification -
Multiplicity 1
Description This parameter defines the PHB value which used for the DSCP value mapping.
The corresponding MML command group: ZQ8B.
Range BE (0), EF (1), AF1 (21), AF2 (22), AF3 (23), AF4 (24)
Step -
Units -
Table 37 phb (PHB value)
50 DN70257257
IP Configuration Plan Interface Parameters
Id:0900d805808e2b75Confidential
IDSP Parameters
Formula for getting internal value
gui ==> internal
BE ==> 0
EF ==> 1
AF1 ==> 21
AF2 ==> 22
AF3 ==> 23
AF4 ==> 24
Default value -
Default value notes Default value is not possible
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • RNC <-> RAC • RAC <-> RACApp
References -
Table 37 phb (PHB value) (Cont.)
DN70257257 51
IP Configuration Plan Interface Parameters IEIF Parameters
Id:0900d805808e2b75Confidential
8 IEIF Parameters
8.1 IPV4Addr (IPv4 address list)
8.2 addrTypeIPV4 (Address type IPv4)
Parameter name IPv4 address list
Abbreviated name IPV4Addr
3GPP name -
Managed Object IEIF
Parameter group -
Classification -
Multiplicity 10
Description IPv4 address list. The corresponding MML command group: ZQRN.
One interface can support 10 physical IP addresses and/or 10 logical IP addresses.
Formula for getting internal value
-
Default value -
Default value notes -
Related functions -
Child parameters • addrTypeIPV4 • addrValueIPV4 • destAddrIPV4 • netmask
Modification On-Line
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • RNC <-> RAC • RAC <-> RACApp
References -
Table 38 IPV4Addr (IPv4 address list)
Parameter name Address type IPv4
Abbreviated name addrTypeIPV4
Table 39 addrTypeIPV4 (Address type IPv4)
52 DN70257257
IP Configuration Plan Interface Parameters
Id:0900d805808e2b75Confidential
IEIF Parameters
8.3 addrValueIPV4 (IP address IPv4)
3GPP name -
Managed Object -
Parameter group -
Classification -
Multiplicity 1
Description The logical or physical IP address for the network interface.
Logical IP address: This address belongs to the specified interface of the specified functional unit. The logical IP address follows the active unit. The logical IP address can be given to 2N and N+1 units. In N+1 units, you have to identify the unit type and the unit index. In 2N units, you only have to identify the unit type of the 2N unit; the unit index is not needed for DMX unit.
Physical IP address: This address is assigned to the specified computer unit per-manently. Note that with the physical IP address you have to identify both the unit type and the unit index. The physical IP address is not allowed in the 2N IP-NIU type units and EIPU units.
The corresponding MML command group: ZQRN
Range Physical (0), Logical (1)
Step -
Units -
Formula for getting internal value
gui ==> internal
Physical ==> 0
Logical ==> 1
Default value -
Default value notes Default value is based on the unit type and index.
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • RNC <-> RAC • RAC <-> RACApp
References -
Table 39 addrTypeIPV4 (Address type IPv4) (Cont.)
Parameter name IP address IPv4
Table 40 addrValueIPV4 (IP address IPv4)
DN70257257 53
IP Configuration Plan Interface Parameters IEIF Parameters
Id:0900d805808e2b75Confidential
8.4 destAddrIPV4 (Destination address IPv4)
Abbreviated name addrValueIPV4
3GPP name -
Managed Object -
Parameter group -
Classification -
Multiplicity 1
Description IPv4 Address, 10 physical addresses and 10 logical addresses can be set for one interface.
The corresponding MML command group: ZQRN, "IP address".
Range 7...15
Step -
Units characters
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • RNC <-> RAC • RAC <-> RACApp
References -
Table 40 addrValueIPV4 (IP address IPv4) (Cont.)
Parameter name Destination address IPv4
Abbreviated name destAddrIPV4
3GPP name -
Managed Object -
Parameter group -
Classification -
Multiplicity 1
Table 41 destAddrIPV4 (Destination address IPv4)
54 DN70257257
IP Configuration Plan Interface Parameters
Id:0900d805808e2b75Confidential
IEIF Parameters
8.5 netmask (Netmask)
Description The IP address of the point-to-point link. This parameter can be given only if the interface type is 'AA', 'IFAI', or 'IFAE'. The corresponding MML command group: ZQRN, "destination IP address".The address is specified in the conventional dot notation (#.#.#.#). The range for each part of the address is from 0 to 255.
The corresponding MML command group: ZQRN, "destination IP address".
Range 7...15
Step -
Units characters
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • RNC <-> RAC • RAC <-> RACApp
References -
Table 41 destAddrIPV4 (Destination address IPv4) (Cont.)
Parameter name Netmask
Abbreviated name netmask
3GPP name -
Managed Object -
Parameter group -
Classification -
Multiplicity 1
Description Netmask for the address.
The corresponding MML command group: ZQRN, "netmask".
Range 7...15
Step -
Units characters
Table 42 netmask (Netmask)
DN70257257 55
IP Configuration Plan Interface Parameters IEIF Parameters
Id:0900d805808e2b75Confidential
8.6 administrativeState (Administrative state)
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • RNC <-> RAC • RAC <-> RACApp
References -
Table 42 netmask (Netmask) (Cont.)
Parameter name Administrative state
Abbreviated name administrativeState
3GPP name -
Managed Object IEIF
Parameter group -
Classification -
Multiplicity 1
Description This parameter indicates the initial administrative state of the interface immediately after the configuration. If the interface is configured for the first time, the default value is "UP". If the state is omitted and the network interface has been configured before, the state does not change.
The corresponding MML command: ZQRN, "state".
Range UP (1), DOWN (3)
Step -
Units -
Formula for getting internal value
gui ==> internal
UP ==> 1
DOWN ==> 3
Default value UP (1)
Default value notes -
Table 43 administrativeState (Administrative state)
56 DN70257257
IP Configuration Plan Interface Parameters
Id:0900d805808e2b75Confidential
IEIF Parameters
8.7 ethIfNetId (Ethernet Interface Identifier)
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • RNC <-> RAC • RAC <-> RACApp
References -
Table 43 administrativeState (Administrative state) (Cont.)
Parameter name Ethernet Interface Identifier
Abbreviated name ethIfNetId
3GPP name -
Managed Object IEIF
Parameter group -
Classification -
Multiplicity 1
Description This parameter identifies the network interface within the IP node entity in the system. The identifier is part of the distinguished name and it is formed in following way: NE-x/IPNO-unitType-unitIndex/IEIF-ifName. For example: RNC-1/IPNO-OMU-0/IEIF-EL0.
The name must start with 'AA' (external or internal IPoA interface), 'IFAE' (external IPOA interface), 'IFAI' (internal IPOA interface), 'EL'(ethernet interface), 'IFETH' and 'IFFGE' (ethernet interface), 'IFFE'and 'IFGE' (ethernet interface), 'LO' (Loop-back interface), or 'VL' (VLAN interface).
The corresponding MML command group: ZQRN, "interface name".
Range 3...8
Step -
Units characters
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes -
Related functions -
Table 44 ethIfNetId (Ethernet Interface Identifier)
DN70257257 57
IP Configuration Plan Interface Parameters IEIF Parameters
Id:0900d805808e2b75Confidential
8.8 ifType (Interface type)
Modification Not modifiable
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • RNC <-> RAC • RAC <-> RACApp
References -
Table 44 ethIfNetId (Ethernet Interface Identifier) (Cont.)
Parameter name Interface type
Abbreviated name ifType
3GPP name -
Managed Object IEIF
Parameter group -
Classification -
Multiplicity 1
Description A numbered or unnumbered point to point interface type for the network interface. This parameter is only valid to ATM ('AA', 'IFAE' and 'IFAI') point to point inter-faces.If you want to change the point to point interface type, you have to remove the interface by using the command QRG and configure it as another point to point interface type.
The numbered interface has a unique IP address. This is the default value.
The unnumbered interface does not have a unique IP address, but it shares its IP address with the Ethernet interface's IP address.
The corresponding MML command group: ZQRN, "point to point interface type".
Range Unnumbered (0), Numbered (1)
Step -
Units -
Formula for getting internal value
gui ==> internal
Unnumbered ==> 0
Numbered ==> 1
Default value Numbered (1)
Default value notes -
Related functions -
Table 45 ifType (Interface type)
58 DN70257257
IP Configuration Plan Interface Parameters
Id:0900d805808e2b75Confidential
IEIF Parameters
8.9 mtu (Maximum Transfer Unit)
Modification Not modifiable
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • RNC <-> RAC • RAC <-> RACApp
References -
Table 45 ifType (Interface type) (Cont.)
Parameter name Maximum Transfer Unit
Abbreviated name mtu
3GPP name -
Managed Object IEIF
Parameter group -
Classification -
Multiplicity 1
Description The maximum transmittable size of a single, complete IP data unit. You can give MTU only for some interfaces.
For LO of DMX units, the value is fixed to 33204.
For LO of chorus units (except NPGE and NPS1), the value is fixed to 16384.
For NPGE LO is 500-4500, and default value is 1500. For NPS1 LO is 500-9180, and default value is 9180.
The range of AA and IFAE is 500-9180, and default value is 9180.
The range of VL, IFGE and IFAI is 500-4500, and default value is 1500.
For EL, IFETH and IFFE, the value is fixed to 1500.
The corresponding MML command group: ZQRN, "MTU".
Range 1... 65535
Step 1
Units -
Formula for getting internal value
internal_value = gui_value
Default value 1500
Default value notes The default value is different based on the unit type and unit interface.
Related functions -
Table 46 mtu (Maximum Transfer Unit)
DN70257257 59
IP Configuration Plan Interface Parameters IEIF Parameters
Id:0900d805808e2b75Confidential
Modification On-Line
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • RNC <-> RAC • RAC <-> RACApp
References -
Table 46 mtu (Maximum Transfer Unit) (Cont.)
60 DN70257257
IP Configuration Plan Interface Parameters
Id:0900d805808e2b75Confidential
IGIF Parameters
9 IGIF Parameters
9.1 RncEthernetBw (EthernetBw)
9.2 ethInterfaceRate (Ethernet interface rate)
Parameter name EthernetBw
Abbreviated name RncEthernetBw
3GPP name -
Managed Object IGIF
Parameter group -
Classification -
Multiplicity 1
Description This parameter defines the ethernet interface bandwidth.
The corresponding MML command: ZQA,"Ethernet interface
bandwidth".
Range 100... 1000
Step 100
Units Mbps
Formula for getting internal value
internal_value = gui_value
Default value 1000
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • RNC <-> RAC • RAC <-> RACApp
References -
Table 47 RncEthernetBw (EthernetBw)
Parameter name Ethernet interface rate
Abbreviated name ethInterfaceRate
Table 48 ethInterfaceRate (Ethernet interface rate)
DN70257257 61
IP Configuration Plan Interface Parameters IGIF Parameters
Id:0900d805808e2b75Confidential
9.3 igifId (Ethernet Interface Identifier)
3GPP name -
Managed Object IGIF
Parameter group -
Classification -
Multiplicity 1
Description This parameter defines the ethernet interface rate. A special rate value 0 indicates that autonegotiation is on.
The corresponding MML command: ZQA,"Ethernet interface rate".
Range Autonegotation (0)
Step -
Units -
Formula for getting internal value
gui ==> internal
Autonegotation ==> 0
Default value Autonegotation (0)
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • RNC <-> RAC • RAC <-> RACApp
References -
Table 48 ethInterfaceRate (Ethernet interface rate) (Cont.)
Parameter name Ethernet Interface Identifier
Abbreviated name igifId
3GPP name -
Managed Object IGIF
Parameter group -
Classification -
Multiplicity 1
Table 49 igifId (Ethernet Interface Identifier)
62 DN70257257
IP Configuration Plan Interface Parameters
Id:0900d805808e2b75Confidential
IGIF Parameters
Description This parameter identifies the Ethernet interface which configures the rate and bandwidth in the system. Only IFGE interface is supported on NPGE(P) unit.
The identifier is part of the distinguished name and it is formed in the following way: NE-x/IPNO-unitType-unitIndex/IGIF-ifName. For example: RNC-1/IPNO-NPGEP-0/IGIF-IFGE0.
The corresponding MML command: ZQA,"interface name".
Range 3...8
Step -
Units characters
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes -
Related functions -
Modification Not modifiable
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • RNC <-> RAC • RAC <-> RACApp
References -
Table 49 igifId (Ethernet Interface Identifier) (Cont.)
DN70257257 63
IP Configuration Plan Interface Parameters IICP Parameters
Id:0900d805808e2b75Confidential
10 IICP Parameters
10.1 echoReplyTmout (Timeout for echo reply re-ceiving)
10.2 echoReqPeriod (Period for echo request packet sending)
Parameter name Timeout for echo reply re-ceiving
Abbreviated name echoReplyTmout
3GPP name -
Managed Object IICP
Parameter group -
Classification -
Multiplicity 1
Description Echo Reply timeout is the maximum time waited for an Echo Reply message after an Echo Request. If an Echo Reply is not received within this time, it is considered lost. Reply Timeout value must be strictly less than request period.
Range 100... 600000
Step 50
Units -
Formula for getting internal value
internal_value = gui_value
Default value 500
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • RAC <-> RNC • RAC <-> RACApp
References -
Table 50 echoReplyTmout (Timeout for echo reply re-ceiving)
Parameter name Period for echo request packet sending
Abbreviated name echoReqPeriod
Table 51 echoReqPeriod (Period for echo request packet sending)
64 DN70257257
IP Configuration Plan Interface Parameters
Id:0900d805808e2b75Confidential
IICP Parameters
10.3 maxLostPkt (maxLostPkt)
3GPP name -
Managed Object IICP
Parameter group -
Classification -
Multiplicity 1
Description Echo Request period is the desired time between two consecutive Echo Request packets sent over network.
Range 150... 600000
Step 50
Units -
Formula for getting internal value
internal_value = gui_value
Default value 1000
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • RAC <-> RNC • RAC <-> RACApp
References -
Table 51 echoReqPeriod (Period for echo request packet sending) (Cont.)
Parameter name maxLostPkt
Abbreviated name maxLostPkt
3GPP name -
Managed Object IICP
Parameter group -
Classification -
Multiplicity 1
Table 52 maxLostPkt (maxLostPkt)
DN70257257 65
IP Configuration Plan Interface Parameters IICP Parameters
Id:0900d805808e2b75Confidential
10.4 payloadLength (payloadLength)
Description This parameter defines the number of icmp echo reply packets that are lost contin-ually, in order for the session to be declared in down state.
Maximum lost packets indicates the number of consecutive lost Echo Replies to be waited for before declaring a session as "Down".
Range 1... 255
Step 1
Units -
Formula for getting internal value
internal_value = gui_value
Default value 5
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • RAC <-> RNC • RAC <-> RACApp
References -
Table 52 maxLostPkt (maxLostPkt) (Cont.)
Parameter name payloadLength
Abbreviated name payloadLength
3GPP name -
Managed Object IICP
Parameter group -
Classification -
Multiplicity 1
Description ICMP Payload length represents the payload size of sent Echo Requests.
Range 0... 128
Step 1
Units -
Formula for getting internal value
internal_value = gui_value
Table 53 payloadLength (payloadLength)
66 DN70257257
IP Configuration Plan Interface Parameters
Id:0900d805808e2b75Confidential
IICP Parameters
10.5 profileId (IICP identifier)
Default value 64
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • RAC <-> RNC • RAC <-> RACApp
References -
Table 53 payloadLength (payloadLength) (Cont.)
Parameter name IICP identifier
Abbreviated name profileId
3GPP name -
Managed Object IICP
Parameter group -
Classification -
Multiplicity 1
Description This parameter defines the IICP profile in the system.
The default profile with the profile id "0" cannot be udpated or deleted.
It exists only in the upload file and is returned for planning purposes.
The identifier is part of the distinguished name and it is formed in the following way: NE-x/IICP-profileId. For example: RNC-02/IICP-1.
The corresponding MML command group: ZYGQ, "profile id".
Range 0... 7
Step 1
Units -
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes -
Related functions -
Table 54 profileId (IICP identifier)
DN70257257 67
IP Configuration Plan Interface Parameters IICP Parameters
Id:0900d805808e2b75Confidential
Modification Not modifiable
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • RAC <-> RNC • RAC <-> RACApp
References -
Table 54 profileId (IICP identifier) (Cont.)
68 DN70257257
IP Configuration Plan Interface Parameters
Id:0900d805808e2b75Confidential
IOAM Parameters
11 IOAM Parameters
11.1 InstanceID (Ethernet OAM Instance ID)
Parameter name Ethernet OAM Instance ID
Abbreviated name InstanceID
3GPP name -
Managed Object IOAM
Parameter group -
Classification -
Multiplicity 1
Description This parameter identifies the Ethernet interface which is for Ethernet OAM. Only IFGE and IFFE interfaces are supported on NPGE(P) unit.
The identifier is part of the distinguished name and it is formed in the following way: NE-x/IPNO-unitType-unitIndex/IOAM-ifName. For example: RNC-1/IPNO-NPGEP-0/IOAM-IFGE0.
The corresponding MML command: ZQAN,"interface name".
Range 3...8
Step -
Units characters
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes -
Related functions -
Modification Not modifiable
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • RNC <-> RAC • RAC <-> RACApp
References -
Table 55 InstanceID (Ethernet OAM Instance ID)
DN70257257 69
IP Configuration Plan Interface Parameters IOAM Parameters
Id:0900d805808e2b75Confidential
11.2 activeMode (Link OAM working Mode)
11.3 adminState (Link OAM Administration State )
Parameter name Link OAM working Mode
Abbreviated name activeMode
3GPP name -
Managed Object IOAM
Parameter group -
Classification -
Multiplicity 1
Description The working mode for Ethernet OAM is defined with the link OAM mode parameter.
The corresponding MML command: ZQAN
Range ACTIVE (1), PASSIVE (2)
Step -
Units -
Formula for getting internal value
gui ==> internal
ACTIVE ==> 1
PASSIVE ==> 2
Default value PASSIVE (2)
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • RNC <-> RAC • RAC <-> RACApp
References -
Table 56 activeMode (Link OAM working Mode)
Parameter name Link OAM Administration State
Abbreviated name adminState
3GPP name -
Managed Object IOAM
Table 57 adminState (Link OAM Administration State )
70 DN70257257
IP Configuration Plan Interface Parameters
Id:0900d805808e2b75Confidential
IOAM Parameters
11.4 almClrTimer (Link OAM Critical Event Alarm Clearance Timer)
Parameter group -
Classification -
Multiplicity 1
Description Ethernet OAM functionality is enabled/disabled with the link OAM administration state parameter. When the feature is disabled, the other Ethernet OAM related parameters do not have any effect.
The corresponding MML command: ZQAN
Range ENABLE (1), DISABLE (2)
Step -
Units -
Formula for getting internal value
gui ==> internal
ENABLE ==> 1
DISABLE ==> 2
Default value DISABLE (2)
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • RNC <-> RAC • RAC <-> RACApp
References -
Table 57 adminState (Link OAM Administration State ) (Cont.)
Parameter name Link OAM Critical Event Alarm Clearance Timer
Abbreviated name almClrTimer
3GPP name -
Managed Object IOAM
Parameter group -
Classification -
Multiplicity 1
Table 58 almClrTimer (Link OAM Critical Event Alarm Clearance Timer)
DN70257257 71
IP Configuration Plan Interface Parameters IOAM Parameters
Id:0900d805808e2b75Confidential
11.5 efEvtThd (Link OAM Error Frame Event Threshold)
Description This parameter defines the time to clean the link OAM critical event alarm when there is no Critical Event Flag received.
If the templateID is given, this parameter must be empty.
If this parameter is filled, the templateID must be empty.
The corresponding MML command: ZQAN
Range 1... 10
Step 1
Units -
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes If the templateID is given, this parameter must be empty.If this parameter is filled, the templateID must be empty.
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • RNC <-> RAC • RAC <-> RACApp
References -
Table 58 almClrTimer (Link OAM Critical Event Alarm Clearance Timer) (Cont.)
Parameter name Link OAM Error Frame Event Threshold
Abbreviated name efEvtThd
3GPP name -
Managed Object IOAM
Parameter group -
Classification -
Multiplicity 1
Table 59 efEvtThd (Link OAM Error Frame Event Threshold)
72 DN70257257
IP Configuration Plan Interface Parameters
Id:0900d805808e2b75Confidential
IOAM Parameters
11.6 efEvtWnd (Link OAM Error Frame Event Window)
Description This parameter defines the threshold for the error frame events. If the received error frames number is beyond the threshold during the window defined by efE-vtWnd, the peer will be alerted with event notification.
If the templateID is given, this parameter must be empty.
If this parameter is filled, the templateID must be empty.
The corresponding MML command: ZQAN
Range 0... 65535
Step 1
Units -
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes If the templateID is given, this parameter must be empty.If this parameter is filled, the templateID must be empty.
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • RNC <-> RAC • RAC <-> RACApp
References -
Table 59 efEvtThd (Link OAM Error Frame Event Threshold) (Cont.)
Parameter name Link OAM Error Frame Event Window
Abbreviated name efEvtWnd
3GPP name -
Managed Object IOAM
Parameter group -
Classification -
Multiplicity 1
Table 60 efEvtWnd (Link OAM Error Frame Event Window)
DN70257257 73
IP Configuration Plan Interface Parameters IOAM Parameters
Id:0900d805808e2b75Confidential
11.7 efSecThd (Link OAM Error Frame Seconds Threshold)
Description This parameter defines the time window for the error frame events statistics.
If the templateID is given, this parameter must be empty.
If this parameter is filled, the templateID must be empty.
The corresponding MML command: ZQAN
Range 1... 60
Step 1
Units -
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • RNC <-> RAC • RAC <-> RACApp
References -
Table 60 efEvtWnd (Link OAM Error Frame Event Window) (Cont.)
Parameter name Link OAM Error Frame Seconds Threshold
Abbreviated name efSecThd
3GPP name -
Managed Object IOAM
Parameter group -
Classification -
Multiplicity 1
Table 61 efSecThd (Link OAM Error Frame Seconds Threshold)
74 DN70257257
IP Configuration Plan Interface Parameters
Id:0900d805808e2b75Confidential
IOAM Parameters
11.8 efSecWnd (Link OAM Error Frame Seconds Window)
Description This parameter defines the threshold for the error frame seconds.
If the error frame is received during 1 second, the second is called the error frame second.
The parameter cannot be greater than efSecWnd.
If the error frame second number is beyond the threshold during the window defined by efSecWnd, the peer will be alerted with event notification.
If the templateID is given, this parameter must be empty.
If this parameter is filled, the templateID must be empty.
The corresponding MML command: ZQAN
Range 0... 900
Step 1
Units -
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes If the templateID is given, this parameter must be empty.If this parameter is filled, the templateID must be empty.
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • RNC <-> RAC • RAC <-> RACApp
References -
Table 61 efSecThd (Link OAM Error Frame Seconds Threshold) (Cont.)
Parameter name Link OAM Error Frame Seconds Window
Abbreviated name efSecWnd
3GPP name -
Managed Object IOAM
Parameter group -
Classification -
Multiplicity 1
Table 62 efSecWnd (Link OAM Error Frame Seconds Window)
DN70257257 75
IP Configuration Plan Interface Parameters IOAM Parameters
Id:0900d805808e2b75Confidential
11.9 lostTimer (Ethernet OAM Link Timeout)
Description This parameter defines the time window for the error frame seconds statistics.
If the templateID is given, this parameter must be empty.
If this parameter is filled, the templateID must be empty.
The corresponding MML command: ZQAN
Range 10... 900
Step 1
Units -
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes If the templateID is given, this parameter must be empty.If this parameter is filled, the templateID must be empty.
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • RNC <-> RAC • RAC <-> RACApp
References -
Table 62 efSecWnd (Link OAM Error Frame Seconds Window) (Cont.)
Parameter name Ethernet OAM Link Timeout
Abbreviated name lostTimer
3GPP name -
Managed Object IOAM
Parameter group -
Classification -
Multiplicity 1
Table 63 lostTimer (Ethernet OAM Link Timeout)
76 DN70257257
IP Configuration Plan Interface Parameters
Id:0900d805808e2b75Confidential
IOAM Parameters
11.10 lpDuration (Link OAM Loopback Duration Time)
Description This parameter is the maximum time that the OAM link peer responses. If the peer response is not received, it shows that the peer is inoperative.
If the parameter is modified, OAM discovery process will be reset.
If the templateID is given, this parameter must be empty.
If this parameter is filled, the templateID must be empty.
The corresponding MML command: ZQAN
Range 2... 30
Step 1
Units -
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes If the templateID is given, this parameter must be empty.If this parameter is filled, the templateID must be empty.
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • RNC <-> RAC • RAC <-> RACApp
References -
Table 63 lostTimer (Ethernet OAM Link Timeout) (Cont.)
Parameter name Link OAM Loopback Duration Time
Abbreviated name lpDuration
3GPP name -
Managed Object IOAM
Parameter group -
Classification -
Multiplicity 1
Table 64 lpDuration (Link OAM Loopback Duration Time)
DN70257257 77
IP Configuration Plan Interface Parameters IOAM Parameters
Id:0900d805808e2b75Confidential
11.11 lpLostTimer (Link OAM Loopback Timeout)
Description This parameter defines the time interval beyond which the remote loopback is dis-abled.
If loopback is enabled by local interface, it will be disabled when this time timeout.
If the templateID is given, this parameter must be empty.
If this parameter is filled, the templateID must be empty.
The corresponding MML command: ZQAN
Range 10... 300
Step 1
Units -
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes If the templateID is given, this parameter must be empty.If this parameter is filled, the templateID must be empty.
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • RNC <-> RAC • RAC <-> RACApp
References -
Table 64 lpDuration (Link OAM Loopback Duration Time) (Cont.)
Parameter name Link OAM Loopback Timeout
Abbreviated name lpLostTimer
3GPP name -
Managed Object IOAM
Parameter group -
Classification -
Multiplicity 1
Table 65 lpLostTimer (Link OAM Loopback Timeout)
78 DN70257257
IP Configuration Plan Interface Parameters
Id:0900d805808e2b75Confidential
IOAM Parameters
11.12 lpPktRate (Link OAM Loopback Packet Rate)
Description This parameter defines the time interval beyond which the local loopback is dis-abled.
If the loopback is enabled by remote interface, it will be disabled when this time timeout.
If the templateID is given, this parameter must be empty.
If this parameter is filled, the templateID must be empty.
The corresponding MML command: ZQAN
Range 10... 300
Step 1
Units -
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes If the templateID is given, this parameter must be empty.If this parameter is filled, the templateID must be empty.
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • RNC <-> RAC • RAC <-> RACApp
References -
Table 65 lpLostTimer (Link OAM Loopback Timeout) (Cont.)
Parameter name Link OAM Loopback Packet Rate
Abbreviated name lpPktRate
3GPP name -
Managed Object IOAM
Parameter group -
Classification -
Multiplicity 1
Table 66 lpPktRate (Link OAM Loopback Packet Rate)
DN70257257 79
IP Configuration Plan Interface Parameters IOAM Parameters
Id:0900d805808e2b75Confidential
11.13 lpPktSize (Link OAM Loopback Packet Size )
Description This parameter defines the packet rate of the test frames during the loopback enabled.
If the templateID is given, this parameter must be empty.
If this parameter is filled, the templateID must be empty.
The corresponding MML command: ZQAN
Range 20... 1000
Step 20
Units -
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes If the templateID is given, this parameter must be empty.If this parameter is filled, the templateID must be empty.
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • RNC <-> RAC • RAC <-> RACApp
References -
Table 66 lpPktRate (Link OAM Loopback Packet Rate) (Cont.)
Parameter name Link OAM Loopback Packet Size
Abbreviated name lpPktSize
3GPP name -
Managed Object IOAM
Parameter group -
Classification -
Multiplicity 1
Table 67 lpPktSize (Link OAM Loopback Packet Size )
80 DN70257257
IP Configuration Plan Interface Parameters
Id:0900d805808e2b75Confidential
IOAM Parameters
11.14 pduTimer (Link OAM PDU Timer)
Description This parameter defines the packet size of the test packets during Loopback enabled.
For IFGE interface, the max packet size is 1518 on NPGE(P) unit.
For IFFE interface, the max packet size is 1514 on NPGE(P) unit.
If the templateID is given, this parameter must be empty.
If this parameter is filled, the templateID must be empty.
The corresponding MML command: ZQAN
Range 64... 1518
Step 1
Units -
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes For IFGE interface, the max packet size is 1518 on NPGE(P) unit.For IFFE inter-face, the max packet size is 1514 on NPGE(P) unit.If the templateID is given, this parameter must be empty.If this parameter is filled, the templateID must be empty.
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • RNC <-> RAC • RAC <-> RACApp
References -
Table 67 lpPktSize (Link OAM Loopback Packet Size ) (Cont.)
Parameter name Link OAM PDU Timer
Abbreviated name pduTimer
3GPP name -
Managed Object IOAM
Parameter group -
Classification -
Multiplicity 1
Table 68 pduTimer (Link OAM PDU Timer)
DN70257257 81
IP Configuration Plan Interface Parameters IOAM Parameters
Id:0900d805808e2b75Confidential
11.15 templateID (Template ID)
Description This parameter defines the time period of sending OAM PDU.
If the templateID is given, this parameter must be empty.
If this parameter is filled, the templateID must be empty.
The corresponding MML command: ZQAN
Range 100... 1000
Step 100
Units -
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes If the templateID is given, this parameter must be empty.If this parameter is filled, the templateID must be empty.
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • RNC <-> RAC • RAC <-> RACApp
References -
Table 68 pduTimer (Link OAM PDU Timer) (Cont.)
Parameter name Template ID
Abbreviated name templateID
3GPP name -
Managed Object IOAM
Parameter group -
Classification -
Multiplicity 1
Table 69 templateID (Template ID)
82 DN70257257
IP Configuration Plan Interface Parameters
Id:0900d805808e2b75Confidential
IOAM Parameters
Description This parameter defines the template ID which used by the OAM link. The OAM template include the following parameters: (pduTimer,lostTimer,lpLostTimer,alm-ClrTimer,efEvtThd,efEvtWnd,efSecThd,efSecWnd,lpDuration,lpPktRate,lpPkt-Size).
If the templateID is given, the above parameters in brackets must be empty.
If any of the above parameters in brackets is filled, the templateID must be empty.
The corresponding MML command: ZQAN
Range 1... 5
Step 1
Units -
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes The OAM template include the following parameters: (pduTimer,lostTimer,lpLost-Timer,almClrTimer,efEvtThd,efEvtWnd,efSecThd,efSecWnd,lpDuration,lpPk-tRate,lpPktSize).If the templateID is given, the above parameters in brackets must be empty.If any of the above parameters in brackets is filled, the templateID must be empty.
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • RNC <-> RAC • RAC <-> RACApp
References -
Table 69 templateID (Template ID) (Cont.)
DN70257257 83
IP Configuration Plan Interface Parameters IOAMT Parameters
Id:0900d805808e2b75Confidential
12 IOAMT Parameters
12.1 almClrTimer (Link OAM Critical Event Alarm Clearance Timer)
12.2 efEvtThd (Link OAM Error Frame Event Threshold)
Parameter name Link OAM Critical Event Alarm Clearance Timer
Abbreviated name almClrTimer
3GPP name -
Managed Object IOAMT
Parameter group -
Classification -
Multiplicity 1
Description This parameter defines the time to clean the link OAM critical event alarm when there is no Critical Event Flag received.
The corresponding MML command: ZQAT
Range 1... 10
Step 1
Units -
Formula for getting internal value
internal_value = gui_value
Default value 5
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • RNC <-> RAC • RAC <-> RACApp
References -
Table 70 almClrTimer (Link OAM Critical Event Alarm Clearance Timer)
Parameter name Link OAM Error Frame Event Threshold
Table 71 efEvtThd (Link OAM Error Frame Event Threshold)
84 DN70257257
IP Configuration Plan Interface Parameters
Id:0900d805808e2b75Confidential
IOAMT Parameters
12.3 efEvtWnd (Link OAM Error Frame Event Window)
Abbreviated name efEvtThd
3GPP name -
Managed Object IOAMT
Parameter group -
Classification -
Multiplicity 1
Description This parameter defines the threshold for the error frame events. If the received error frames number is beyond the threshold during the window defined by efE-vtWnd, the peer will be alerted with event notification.
The corresponding MML command: ZQAT
Range 0... 65535
Step 1
Units -
Formula for getting internal value
internal_value = gui_value
Default value 1
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • RNC <-> RAC • RAC <-> RACApp
References -
Table 71 efEvtThd (Link OAM Error Frame Event Threshold) (Cont.)
Parameter name Link OAM Error Frame Event Window
Abbreviated name efEvtWnd
3GPP name -
Managed Object IOAMT
Parameter group -
Classification -
Table 72 efEvtWnd (Link OAM Error Frame Event Window)
DN70257257 85
IP Configuration Plan Interface Parameters IOAMT Parameters
Id:0900d805808e2b75Confidential
12.4 efSecThd (Link OAM Error Frame Seconds Threshold )
Multiplicity 1
Description This parameter defines the time window for the error frame events statistics.
The corresponding MML command: ZQAT
Range 1... 60
Step 1
Units -
Formula for getting internal value
internal_value = gui_value
Default value 1
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • RNC <-> RAC • RAC <-> RACApp
References -
Table 72 efEvtWnd (Link OAM Error Frame Event Window) (Cont.)
Parameter name Link OAM Error Frame Seconds Threshold
Abbreviated name efSecThd
3GPP name -
Managed Object IOAMT
Parameter group -
Classification -
Multiplicity 1
Table 73 efSecThd (Link OAM Error Frame Seconds Threshold )
86 DN70257257
IP Configuration Plan Interface Parameters
Id:0900d805808e2b75Confidential
IOAMT Parameters
12.5 efSecWnd (Link OAM Error Frame Seconds Window)
Description This parameter defines the threshold for the error frame seconds.
If the error frame is received during 1 second, the second is called the error frame second.
The parameter cannot be greater than efSecWnd.
If the error frame second number is beyond the threshold during the window defined by efSecWnd, the peer will be alerted with event notification.
The corresponding MML command: ZQAT
Range 0... 900
Step 1
Units -
Formula for getting internal value
internal_value = gui_value
Default value 1
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • RNC <-> RAC • RAC <-> RACApp
References -
Table 73 efSecThd (Link OAM Error Frame Seconds Threshold ) (Cont.)
Parameter name Link OAM Error Frame Seconds Window
Abbreviated name efSecWnd
3GPP name -
Managed Object IOAMT
Parameter group -
Classification -
Multiplicity 1
Description This parameter defines the time window for the error frame seconds statistics.
The corresponding MML command: ZQAT
Table 74 efSecWnd (Link OAM Error Frame Seconds Window)
DN70257257 87
IP Configuration Plan Interface Parameters IOAMT Parameters
Id:0900d805808e2b75Confidential
12.6 lostTimer (Ethernet OAM Link Timeout)
Range 10... 900
Step 1
Units -
Formula for getting internal value
internal_value = gui_value
Default value 60
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • RNC <-> RAC • RAC <-> RACApp
References -
Table 74 efSecWnd (Link OAM Error Frame Seconds Window) (Cont.)
Parameter name Ethernet OAM Link Timeout
Abbreviated name lostTimer
3GPP name -
Managed Object IOAMT
Parameter group -
Classification -
Multiplicity 1
Description This parameter is the maximum time that the OAM link peer responses. If the peer response is not received, it shows that the peer is inoperative.
The corresponding MML command: ZQAT
Range 2... 30
Step 1
Units -
Formula for getting internal value
internal_value = gui_value
Default value 5
Table 75 lostTimer (Ethernet OAM Link Timeout)
88 DN70257257
IP Configuration Plan Interface Parameters
Id:0900d805808e2b75Confidential
IOAMT Parameters
12.7 lpDuration (Link OAM Loopback Duration Time)
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • RNC <-> RAC • RAC <-> RACApp
References -
Table 75 lostTimer (Ethernet OAM Link Timeout) (Cont.)
Parameter name Link OAM Loopback Duration Time
Abbreviated name lpDuration
3GPP name -
Managed Object IOAMT
Parameter group -
Classification -
Multiplicity 1
Description This parameter defines the time interval beyond which the remote loopback is dis-abled.
If loopback is enabled by local interface, it will be disabled when this time timeout.
The corresponding MML command: ZQAT
Range 10... 300
Step 10
Units -
Formula for getting internal value
internal_value = gui_value
Default value 10
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Table 76 lpDuration (Link OAM Loopback Duration Time)
DN70257257 89
IP Configuration Plan Interface Parameters IOAMT Parameters
Id:0900d805808e2b75Confidential
12.8 lpLostTimer (Link OAM Loopback Timeout)
Related options -
Feature dependencies -
Interfaces • RNC <-> RAC • RAC <-> RACApp
References -
Table 76 lpDuration (Link OAM Loopback Duration Time) (Cont.)
Parameter name Link OAM Loopback Timeout
Abbreviated name lpLostTimer
3GPP name -
Managed Object IOAMT
Parameter group -
Classification -
Multiplicity 1
Description This parameter defines the time interval beyond which the local loopback is dis-abled.
If the loopback is enabled by remote interface, it will be disabled when this time timeout.
The corresponding MML command: ZQAT
Range 10... 300
Step 1
Units -
Formula for getting internal value
internal_value = gui_value
Default value 10
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • RNC <-> RAC • RAC <-> RACApp
Table 77 lpLostTimer (Link OAM Loopback Timeout)
90 DN70257257
IP Configuration Plan Interface Parameters
Id:0900d805808e2b75Confidential
IOAMT Parameters
12.9 lpPktRate (Link OAM Loopback Packet Rate)
12.10 lpPktSize (Link OAM Loopback Packet Size)
References -
Table 77 lpLostTimer (Link OAM Loopback Timeout) (Cont.)
Parameter name Link OAM Loopback Packet Rate
Abbreviated name lpPktRate
3GPP name -
Managed Object IOAMT
Parameter group -
Classification -
Multiplicity 1
Description This parameter defines the packet rate of the test frames during the loopback enabled.
The corresponding MML command: ZQAT
Range 20... 1000
Step 20
Units -
Formula for getting internal value
internal_value = gui_value
Default value 20
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • RNC <-> RAC • RAC <-> RACApp
References -
Table 78 lpPktRate (Link OAM Loopback Packet Rate)
Parameter name Link OAM Loopback Packet Size
Table 79 lpPktSize (Link OAM Loopback Packet Size)
DN70257257 91
IP Configuration Plan Interface Parameters IOAMT Parameters
Id:0900d805808e2b75Confidential
12.11 pduTimer (Link OAM PDU Timer)
Abbreviated name lpPktSize
3GPP name -
Managed Object IOAMT
Parameter group -
Classification -
Multiplicity 1
Description This parameter defines the packet size of the test packets during Loopback enabled.
For IFGE interface, the max packet size is 1518 on NPGE(P) unit.
For IFFE interface, the max packet size is 1514 on NPGE(P) unit.
The corresponding MML command: ZQAT
Range 64... 1518
Step 1
Units -
Formula for getting internal value
internal_value = gui_value
Default value 64
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • RNC <-> RAC • RAC <-> RACApp
References -
Table 79 lpPktSize (Link OAM Loopback Packet Size) (Cont.)
Parameter name Link OAM PDU Timer
Abbreviated name pduTimer
3GPP name -
Managed Object IOAMT
Parameter group -
Table 80 pduTimer (Link OAM PDU Timer)
92 DN70257257
IP Configuration Plan Interface Parameters
Id:0900d805808e2b75Confidential
IOAMT Parameters
12.12 templateID (Template ID)
Classification -
Multiplicity 1
Description This parameter defines the time period of sending OAM PDU.
The corresponding MML command: ZQAT
Range 100... 1000
Step 100
Units -
Formula for getting internal value
internal_value = gui_value
Default value 1000
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • RNC <-> RAC • RAC <-> RACApp
References -
Table 80 pduTimer (Link OAM PDU Timer) (Cont.)
Parameter name Template ID
Abbreviated name templateID
3GPP name -
Managed Object IOAMT
Parameter group -
Classification -
Multiplicity 1
Description This parameter defines the Ethernet OAM template in the system.
The identifier is part of
the distinguished name and it is formed in the following way: NE-x/IOAMT-tem-plateId. For example: RNC-02/IOAMT-1.
The corresponding MML command group: ZQAT, "Template ID".
Table 81 templateID (Template ID)
DN70257257 93
IP Configuration Plan Interface Parameters IOAMT Parameters
Id:0900d805808e2b75Confidential
12.13 templateName (Ethernet OAM Template Name)
Range 1... 5
Step 1
Units -
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes -
Related functions -
Modification Not modifiable
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • RNC <-> RAC • RAC <-> RACApp
References -
Table 81 templateID (Template ID) (Cont.)
Parameter name Ethernet OAM Template Name
Abbreviated name templateName
3GPP name -
Managed Object IOAMT
Parameter group -
Classification -
Multiplicity 1
Description This parameter defines the template name which is used for OAM link.
The corresponding MML command: ZQAT
Range 1...10
Step -
Units characters
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes -
Table 82 templateName (Ethernet OAM Template Name)
94 DN70257257
IP Configuration Plan Interface Parameters
Id:0900d805808e2b75Confidential
IOAMT Parameters
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • RNC <-> RAC • RAC <-> RACApp
References -
Table 82 templateName (Ethernet OAM Template Name) (Cont.)
DN70257257 95
IP Configuration Plan Interface Parameters IOPF Parameters
Id:0900d805808e2b75Confidential
13 IOPF Parameters
13.1 iopfId (IOPF Identifier)
13.2 rfc1583comp (RFC1583 Compatibility)
Parameter name IOPF Identifier
Abbreviated name iopfId
3GPP name -
Managed Object IOPF
Parameter group -
Classification -
Multiplicity 1
Description This parameter identifies the OSPF configuration entity in the system. There is only one instance in IPNO. The identifier is part of the distinguished name and it is formed in a following way: NE-x/IPNO-unitType-unitIndex/IOPF-x. For example: RNC-1/IPNO-OMU-0/IOPF-1. The corresponding MML command group: ZQKI.
Range 1... 1
Step 1
Units -
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes -
Related functions -
Modification Not modifiable
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • RNC <-> RAC • RAC <-> RACApp
References -
Table 83 iopfId (IOPF Identifier)
Parameter name RFC1583 Compatibility
Abbreviated name rfc1583comp
Table 84 rfc1583comp (RFC1583 Compatibility)
96 DN70257257
IP Configuration Plan Interface Parameters
Id:0900d805808e2b75Confidential
IOPF Parameters
13.3 routeId (Router Id)
3GPP name -
Managed Object IOPF
Parameter group -
Classification -
Multiplicity 1
Description This implementation of OSPF is based on RFC2178, which fixes some looping problems in an earlier specification of OSPF. If this implementation is running in the environment with OSPF implementations based on RFC1583 or earlier, this OSPF must run in the compatibility mode. This ensures backwards compatibility. The default value is "Yes" (enabled). Yes = RFC1583 compatibility is enabled. No = RFC1583 compatibility is disabled. The corresponding MML command group: ZQKS, "rfc1583compatibility".
Range No (0), Yes (1)
Step -
Units -
Formula for getting internal value
gui ==> internal
No ==> 0
Yes ==> 1
Default value Yes (1)
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • RAC <-> RNC • RACApp <-> RAC
References -
Table 84 rfc1583comp (RFC1583 Compatibility) (Cont.)
Parameter name Router Id
Abbreviated name routeId
3GPP name -
Managed Object IOPF
Table 85 routeId (Router Id)
DN70257257 97
IP Configuration Plan Interface Parameters IOPF Parameters
Id:0900d805808e2b75Confidential
13.4 spfDelay (SPF Delay)
Parameter group -
Classification -
Multiplicity 1
Description The router identification is given in the form of an IP address. The Router ID spec-ifies a number that uniquely defines the router in a routing domain. Selecting an existing IP address in the unit as the OSPF router ID inherently makes it unique.
The IP network number of a subnetwork can be used as the area ID.
Set the router ID yourself and do not rely on the system to pick a router ID based on an IP address. This is to prevent the router ID from changing if the interface used for the router ID goes down.
Give the value as a dotted quad, for example [0-255].[0-255].[0-255].[0-255]. If you do not give a router ID, the router selects internally the highest interface address at the time of OSPF being enabled. The corresponding MML command: ZQKS, "router identification".
Do not use the 0.0.0.0 router ID, because by the 0.0.0.0 value the current router ID is taken out of use.
Range 7...15
Step -
Units characters
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes Default is empty.
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • RAC <-> RNC • RACApp <-> RAC
References -
Table 85 routeId (Router Id) (Cont.)
Parameter name SPF Delay
Abbreviated name spfDelay
Table 86 spfDelay (SPF Delay)
98 DN70257257
IP Configuration Plan Interface Parameters
Id:0900d805808e2b75Confidential
IOPF Parameters
13.5 spfHoldtime (SPF Holdtime)
3GPP name -
Managed Object IOPF
Parameter group -
Classification -
Multiplicity 1
Description The parameter defines the waiting time before recalculating the OSPF routing table after a change in the topology.
The corresponding MML command group: ZQKS, "spf delay".
Range 1... 60
Step 1
Units seconds
Formula for getting internal value
internal_value = gui_value
Default value 2
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • RAC <-> RNC • RACApp <-> RAC
References -
Table 86 spfDelay (SPF Delay) (Cont.)
Parameter name SPF Holdtime
Abbreviated name spfHoldtime
3GPP name -
Managed Object IOPF
Parameter group -
Classification -
Multiplicity 1
Table 87 spfHoldtime (SPF Holdtime)
DN70257257 99
IP Configuration Plan Interface Parameters IOPF Parameters
Id:0900d805808e2b75Confidential
Description This parameter defines the minimum time between the recalculations of the OSPF routing table.
The corresponding MML command group: ZQKS, "spf hold time".
Range 1... 60
Step 1
Units seconds
Formula for getting internal value
internal_value = gui_value
Default value 5
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • RAC <-> RNC • RACApp <-> RAC
References -
Table 87 spfHoldtime (SPF Holdtime) (Cont.)
100 DN70257257
IP Configuration Plan Interface Parameters
Id:0900d805808e2b75Confidential
IPBR Parameters
14 IPBR Parameters
14.1 committedBW (Committed BW)
14.2 committedDcnBW (Committed DCN BW)
Parameter name Committed BW
Abbreviated name committedBW
3GPP name -
Managed Object IPBR
Parameter group -
Classification -
Multiplicity 1
Description This parameter defines the committed BW for the IP based route.
Corresponding MML command: ZQRU, "committed bandwidth of ip based route".
There is one rule about related bandwidth parameters.
routeBW >= committedBW > committedDcnBW + committedSigBW
Range 0... 1000000
Step 1
Units kbps
Formula for getting internal value
internal_value = gui_value
Default value 0
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • RNC <-> RAC • RAC <-> RACApp
References -
Table 88 committedBW (Committed BW)
Parameter name Committed DCN BW
Table 89 committedDcnBW (Committed DCN BW)
DN70257257 101
IP Configuration Plan Interface Parameters IPBR Parameters
Id:0900d805808e2b75Confidential
14.3 committedSigBW (Committed signal BW )
Abbreviated name committedDcnBW
3GPP name -
Managed Object IPBR
Parameter group -
Classification -
Multiplicity 1
Description This parameter defines the committed DCN bandwidth for IP based route.
The corresponding MML command: ZQRU, "committed bandwidth of DCN".
There is one rule about related bandwidth parameters.
routeBW >= committedBW > committedDcnBW + committedSigBW
Range 0... 1000
Step 1
Units kbps
Formula for getting internal value
internal_value = gui_value
Default value 0
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • RNC <-> RAC • RAC <-> RACApp
References -
Table 89 committedDcnBW (Committed DCN BW) (Cont.)
Parameter name Committed signal BW
Abbreviated name committedSigBW
3GPP name -
Managed Object IPBR
Parameter group -
Classification -
Table 90 committedSigBW (Committed signal BW )
102 DN70257257
IP Configuration Plan Interface Parameters
Id:0900d805808e2b75Confidential
IPBR Parameters
14.4 ifcFlag (IP IFC Flag)
Multiplicity 1
Description This parameter defines the committed signaling bandwidth for ip based route.
The corresponding MML command: ZQRU, "committed signaling bandwidth".
There is one rule about related bandwidth parameters.
routeBW >= committedBW > committedDcnBW + committedSigBW
Range 0... 50000
Step 1
Units kbps
Formula for getting internal value
internal_value = gui_value
Default value 0
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • RAC <-> RNC • RAC <-> RACApp
References -
Table 90 committedSigBW (Committed signal BW ) (Cont.)
Parameter name IP IFC Flag
Abbreviated name ifcFlag
3GPP name -
Managed Object IPBR
Parameter group -
Classification -
Multiplicity 1
Description This parameter defines whether the internal flow control is used or not.
The corresponding MML command: ZQRU, "ifcmethod".
Range OFF (0), ON (1)
Step -
Table 91 ifcFlag (IP IFC Flag)
DN70257257 103
IP Configuration Plan Interface Parameters IPBR Parameters
Id:0900d805808e2b75Confidential
14.5 ipBasedRouteName (IP based route name)
Units -
Formula for getting internal value
gui ==> internal
OFF ==> 0
ON ==> 1
Default value OFF (0)
Default value notes -
Related functions -
Modification Not modifiable
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • RNC <-> RAC • RAC <-> RACApp
References -
Table 91 ifcFlag (IP IFC Flag) (Cont.)
Parameter name IP based route name
Abbreviated name ipBasedRouteName
3GPP name -
Managed Object IPBR
Parameter group -
Classification -
Multiplicity 1
Description This parameter defines the name of the IP based route.
The IP based route name is unique in the RNC.
The corresponding MML command: ZQRU, "IP based route name".
Range 1...16
Step -
Units characters
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes Default value is not possible
Table 92 ipBasedRouteName (IP based route name)
104 DN70257257
IP Configuration Plan Interface Parameters
Id:0900d805808e2b75Confidential
IPBR Parameters
14.6 ipbrId (IP based route id)
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • RNC <-> RAC • RAC <-> RACApp
References -
Table 92 ipBasedRouteName (IP based route name) (Cont.)
Parameter name IP based route id
Abbreviated name ipbrId
3GPP name -
Managed Object IPBR
Parameter group -
Classification -
Multiplicity 1
Description This parameter identifies the IP based route.
The IP based route id is unique in the RNC.
The identifier is part of the distinguished name and it is formed in the following way: NE-x/IPBR-ipbrId. For example: RNC-1/IPBR-1.
The corresponding MML command: ZQRU, "ip based route id".
Range 1... 4095
Step 1
Units -
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes -
Related functions -
Modification Not modifiable
Related parameters -
Parameter relationships -
Table 93 ipbrId (IP based route id)
DN70257257 105
IP Configuration Plan Interface Parameters IPBR Parameters
Id:0900d805808e2b75Confidential
14.7 localMuxUDPPort (IP multiplexing local UDP port)
Related options -
Feature dependencies -
Interfaces • RNC <-> RAC • RAC <-> RACApp
References -
Table 93 ipbrId (IP based route id) (Cont.)
Parameter name IP multiplexing local UDP port
Abbreviated name localMuxUDPPort
3GPP name -
Managed Object IPBR
Parameter group -
Classification -
Multiplicity 1
Description This parameter defines the local UDP port for IP multiplexing.
The corresponding MML commands: QRU, QRL, "IP multiplexing local UDP port".
Range 49152... 65535
Step 1
Units -
Formula for getting internal value
internal_value = gui_value
Default value 65535
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options • Efficient Transport for Small IP Packets
Feature dependencies -
Interfaces • RNC <-> RAC • RAC <-> RACApp
References -
Table 94 localMuxUDPPort (IP multiplexing local UDP port)
106 DN70257257
IP Configuration Plan Interface Parameters
Id:0900d805808e2b75Confidential
IPBR Parameters
14.8 maxMuxPackets (IP multiplexing max packets)
14.9 ratio (Ratio )
Parameter name IP multiplexing max packets
Abbreviated name maxMuxPackets
3GPP name -
Managed Object IPBR
Parameter group -
Classification -
Multiplicity 1
Description This parameter defines the maximum number of packets in one multiplexed packet for IP multiplexing.
The corresponding MML commands: QRU, QRL, "IP multiplexing max packets".
Range 1... 30
Step 1
Units -
Formula for getting internal value
internal_value = gui_value
Default value 30
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options • Efficient Transport for Small IP Packets
Feature dependencies -
Interfaces • RNC <-> RAC • RAC <-> RACApp
References -
Table 95 maxMuxPackets (IP multiplexing max packets)
Parameter name Ratio
Abbreviated name ratio
3GPP name -
Managed Object IPBR
Table 96 ratio (Ratio )
DN70257257 107
IP Configuration Plan Interface Parameters IPBR Parameters
Id:0900d805808e2b75Confidential
14.10 remoteMuxUDPPort (IP multiplexing remote UDP port)
Parameter group -
Classification -
Multiplicity 1
Description This parameter defines the Ratio for Iur/(Iub+Iur).
The corresponding MML command: ZQRU,"ratio".
Range 0... 100
Step 1
Units -
Formula for getting internal value
internal_value = gui_value
Default value 20
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • RNC <-> RAC • RAC <-> RACApp
References -
Table 96 ratio (Ratio ) (Cont.)
Parameter name IP multiplexing remote UDP port
Abbreviated name remoteMuxUDPPort
3GPP name -
Managed Object IPBR
Parameter group -
Classification -
Multiplicity 1
Description This parameter defines the remote UDP port for IP multiplexing.
The corresponding MML commands: QRU, QRL, "IP multiplexing remote UDP port".
Range 49152... 65535
Table 97 remoteMuxUDPPort (IP multiplexing remote UDP port)
108 DN70257257
IP Configuration Plan Interface Parameters
Id:0900d805808e2b75Confidential
IPBR Parameters
14.11 routeBW (Route bandwidth)
Step 1
Units -
Formula for getting internal value
internal_value = gui_value
Default value 65535
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options • Efficient Transport for Small IP Packets
Feature dependencies -
Interfaces • RNC <-> RAC • RAC <-> RACApp
References -
Table 97 remoteMuxUDPPort (IP multiplexing remote UDP port) (Cont.)
Parameter name Route bandwidth
Abbreviated name routeBW
3GPP name -
Managed Object IPBR
Parameter group -
Classification -
Multiplicity 1
Description This parameters defines the route bandwidth for IP based route.
The corresponding MML command: ZQRU, "route bandwidth of ip based route".
There is one rule about related bandwidth parameters.
routeBW >= committedBW > committedDcnBW + committedSigBW
Range 0... 1000000
Step 1
Units kbps
Formula for getting internal value
internal_value = gui_value
Default value 0
Table 98 routeBW (Route bandwidth)
DN70257257 109
IP Configuration Plan Interface Parameters IPBR Parameters
Id:0900d805808e2b75Confidential
14.12 udpMuxDSCP (IP multiplexing DSCP value)
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • RNC <-> RAC • RAC <-> RACApp
References -
Table 98 routeBW (Route bandwidth) (Cont.)
Parameter name IP multiplexing DSCP value
Abbreviated name udpMuxDSCP
3GPP name -
Managed Object IPBR
Parameter group -
Classification -
Multiplicity 1
Description This parameter defines the DSCP value for IP multiplexing.
The corresponding MML commands: QRU, QRL, "IP multiplexing DSCP value".
Range 0... 63
Step 1
Units -
Formula for getting internal value
internal_value = gui_value
Default value 46
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options • Efficient Transport for Small IP Packets
Feature dependencies -
Table 99 udpMuxDSCP (IP multiplexing DSCP value)
110 DN70257257
IP Configuration Plan Interface Parameters
Id:0900d805808e2b75Confidential
IPBR Parameters
14.13 udpMuxEnabled (IP multiplexing flag)
Interfaces • RNC <-> RAC • RAC <-> RACApp
References -
Table 99 udpMuxDSCP (IP multiplexing DSCP value) (Cont.)
Parameter name IP multiplexing flag
Abbreviated name udpMuxEnabled
3GPP name -
Managed Object IPBR
Parameter group -
Classification -
Multiplicity 1
Description This parameter defines whether IP multiplexing is enabled or not.
The corresponding MML commands: QRU, QRL, "IP multiplexing".
Range Disable (0), Enable (1)
Step -
Units -
Formula for getting internal value
gui ==> internal
Disable ==> 0
Enable ==> 1
Default value Disable (0)
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options • Efficient Transport for Small IP Packets
Feature dependencies -
Interfaces • RNC <-> RAC • RAC <-> RACApp
References -
Table 100 udpMuxEnabled (IP multiplexing flag)
DN70257257 111
IP Configuration Plan Interface Parameters IPHB Parameters
Id:0900d805808e2b75Confidential
15 IPHB Parameters
15.1 phbId (PHB profile Identifier)
Parameter name PHB profile Identifier
Abbreviated name phbId
3GPP name -
Managed Object IPHB
Parameter group -
Classification -
Multiplicity 1
Description This parameter identifies the PHB profile ID.
The profile id 0 is the default profile and it cannot be updated or deleted. It exists only in the upload file for planning purposes.
The profile id is unique in the RNC.
The identifier is part of the distinguished name and it is formed in the following way:
NE-x/IPHB-phbId. For example: RNC-1/IPHB-1.
The corresponding MML command group: ZQ8V, "profile id".
Range 0... 10
Step 1
Units -
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes -
Related functions -
Modification Not modifiable
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • RNC <-> RAC • RAC <-> RACApp
References -
Table 101 phbId (PHB profile Identifier)
112 DN70257257
IP Configuration Plan Interface Parameters
Id:0900d805808e2b75Confidential
IPHB Parameters
15.2 phbProfileName (PHB profile name)
15.3 profileList (PHB Profile List)
Parameter name PHB profile name
Abbreviated name phbProfileName
3GPP name -
Managed Object IPHB
Parameter group -
Classification -
Multiplicity 1
Description This parameter defines the PHB profile name.
The profile name 'DEFAULT' is the default profile and it cannot be updated or deleted. It exists only in the upload file for planning purposes.
The profile name is unique in the RNC.
The corresponding MML command group: ZQ8V, "profile name".
Range 1...20
Step -
Units characters
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • RAC <-> RNC • RACApp <-> RAC
References -
Table 102 phbProfileName (PHB profile name)
Parameter name PHB Profile List
Abbreviated name profileList
Table 103 profileList (PHB Profile List)
DN70257257 113
IP Configuration Plan Interface Parameters IPHB Parameters
Id:0900d805808e2b75Confidential
15.4 expWeig (Exponential weight factor)
3GPP name -
Managed Object IPHB
Parameter group -
Classification -
Multiplicity 6
Description This parameter defines the PHB profile.
The corresponding MML command group: ZQ8V.
Formula for getting internal value
-
Default value -
Default value notes -
Related functions -
Child parameters • expWeig • length • maxDrop • maxThreshold • minThreshold • phb • quePriority • queWeight • schedule • vlanPri
Modification On-Line
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • RNC <-> RAC • RAC <-> RACApp
References -
Table 103 profileList (PHB Profile List) (Cont.)
Parameter name Exponential weight factor
Abbreviated name expWeig
3GPP name -
Table 104 expWeig (Exponential weight factor)
114 DN70257257
IP Configuration Plan Interface Parameters
Id:0900d805808e2b75Confidential
IPHB Parameters
15.5 length (Queue length)
Managed Object -
Parameter group -
Classification -
Multiplicity 1
Description This parameter defines the exponential weight factor.
The corresponding MML command: ZQ8V, "Exponential weight factor."
Range 0... 0
Step 1
Units -
Formula for getting internal value
internal_value = gui_value
Default value 0
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • RNC <-> RAC • RAC <-> RACApp
References -
Table 104 expWeig (Exponential weight factor) (Cont.)
Parameter name Queue length
Abbreviated name length
3GPP name -
Managed Object -
Parameter group -
Classification -
Multiplicity 1
Table 105 length (Queue length)
DN70257257 115
IP Configuration Plan Interface Parameters IPHB Parameters
Id:0900d805808e2b75Confidential
15.6 maxDrop (Max drop value)
Description This parameter defines the queue length. The value is constant for different PHB values. The value is 500 for the BE PHB. The value is 300 for the AF1, AF2 and AF3 PHB. The value is 100 for the AF4 and EF profile.
Range 0... 500
Step 1
Units -
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes Default value is decided by PHB.
Related functions -
Modification Not modifiable
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • RNC <-> RAC • RAC <-> RACApp
References -
Table 105 length (Queue length) (Cont.)
Parameter name Max drop value
Abbreviated name maxDrop
3GPP name -
Managed Object -
Parameter group -
Classification -
Multiplicity 1
Description This parameter defines the WRED maximum drop probability value.
The corresponding MML command group: ZQ8V, "wred max drop probability".
Range 0... 100
Step 1
Units %
Table 106 maxDrop (Max drop value)
116 DN70257257
IP Configuration Plan Interface Parameters
Id:0900d805808e2b75Confidential
IPHB Parameters
15.7 maxThreshold (Max threshold)
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes Default value is not possible
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • RNC <-> RAC • RAC <-> RACApp
References -
Table 106 maxDrop (Max drop value) (Cont.)
Parameter name Max threshold
Abbreviated name maxThreshold
3GPP name -
Managed Object -
Parameter group -
Classification -
Multiplicity 1
Description This parameter defines the WRED maximum thresholds.
For the current PHB, this value is always 100.
The corresponding MML command group: ZQ8V.
Range 100... 100
Step 1
Units %
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes Default value is not possible
Related functions -
Modification On-Line
Table 107 maxThreshold (Max threshold)
DN70257257 117
IP Configuration Plan Interface Parameters IPHB Parameters
Id:0900d805808e2b75Confidential
15.8 minThreshold (Min threshold)
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • RNC <-> RAC • RAC <-> RACApp
References -
Table 107 maxThreshold (Max threshold) (Cont.)
Parameter name Min threshold
Abbreviated name minThreshold
3GPP name -
Managed Object -
Parameter group -
Classification -
Multiplicity 1
Description This parameter defines the WRED minimum thresholds.
The corresponding MML command group: ZQ8V.
Range 0... 100
Step 1
Units %
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • RNC <-> RAC • RAC <-> RACApp
References -
Table 108 minThreshold (Min threshold)
118 DN70257257
IP Configuration Plan Interface Parameters
Id:0900d805808e2b75Confidential
IPHB Parameters
15.9 phb (PHB value)
Parameter name PHB value
Abbreviated name phb
3GPP name -
Managed Object -
Parameter group -
Classification -
Multiplicity 1
Description This parameter defines the PHB value.
The corresponding MML command group: ZQ8V.
Range BE (0), EF (1), AF1 (21), AF2 (22), AF3 (23), AF4 (24)
Step -
Units -
Formula for getting internal value
gui ==> internal
BE ==> 0
EF ==> 1
AF1 ==> 21
AF2 ==> 22
AF3 ==> 23
AF4 ==> 24
Default value -
Default value notes Default value is not possible
Related functions -
Modification Not modifiable
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • RNC <-> RAC • RAC <-> RACApp
References -
Table 109 phb (PHB value)
DN70257257 119
IP Configuration Plan Interface Parameters IPHB Parameters
Id:0900d805808e2b75Confidential
15.10 quePriority (Queue priority)
15.11 queWeight (Queue weight)
Parameter name Queue priority
Abbreviated name quePriority
3GPP name -
Managed Object -
Parameter group -
Classification -
Multiplicity 1
Description This parameter defines the attribute of the queue whether it is RT or NRT.
This value is constant for the PHB. It is RT for PHB (AF4 and EF) and NRT for the other PHB.
Range NRT (0), RT (1)
Step -
Units -
Formula for getting internal value
gui ==> internal
NRT ==> 0
RT ==> 1
Default value -
Default value notes -
Related functions -
Modification Not modifiable
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • RNC <-> RAC • RAC <-> RACApp
References -
Table 110 quePriority (Queue priority)
Parameter name Queue weight
Abbreviated name queWeight
3GPP name -
Table 111 queWeight (Queue weight)
120 DN70257257
IP Configuration Plan Interface Parameters
Id:0900d805808e2b75Confidential
IPHB Parameters
15.12 schedule (Queue schedule)
Managed Object -
Parameter group -
Classification -
Multiplicity 1
Description This parameter defines the queue weight.
This value is not valid for the EF PHB, so it should skip in the dowload and upload file.
The corresponding MML command group: ZQ8V, "queue weight".
Range 1... 10000
Step 1
Units -
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • RNC <-> RAC • RAC <-> RACApp
References -
Table 111 queWeight (Queue weight) (Cont.)
Parameter name Queue schedule
Abbreviated name schedule
3GPP name -
Managed Object -
Parameter group -
Classification -
Multiplicity 1
Table 112 schedule (Queue schedule)
DN70257257 121
IP Configuration Plan Interface Parameters IPHB Parameters
Id:0900d805808e2b75Confidential
15.13 vlanPri (Vlan priority)
Description This parameter defines the queue schedule type.
This value is constant for different PHB values. The value is SP for EF PHB, and WRR for other PHB.
Range WRR SCHED (2), SP SCHED (4)
Step -
Units -
Formula for getting internal value
gui ==> internal
WRR SCHED ==> 2
SP SCHED ==> 4
Default value -
Default value notes The default value is decided by PHB.
Related functions -
Modification Not modifiable
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • RNC <-> RAC • RAC <-> RACApp
References -
Table 112 schedule (Queue schedule) (Cont.)
Parameter name Vlan priority
Abbreviated name vlanPri
3GPP name -
Managed Object -
Parameter group -
Classification -
Multiplicity 1
Description This parameter defines the VLAN priority for this PHB value.
The corresponding MML command group: ZQ8V, "vlan priority". Even though this parameter can be modified On-Line, a new value is only taken into use after the next interface unit reset.
Range 0... 7
Table 113 vlanPri (Vlan priority)
122 DN70257257
IP Configuration Plan Interface Parameters
Id:0900d805808e2b75Confidential
IPHB Parameters
Step 1
Units -
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes Default value is not possible
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • RNC <-> RAC • RAC <-> RACApp
References -
Table 113 vlanPri (Vlan priority) (Cont.)
DN70257257 123
IP Configuration Plan Interface Parameters IPNO Parameters
Id:0900d805808e2b75Confidential
16 IPNO Parameters
16.1 IPForwardingIPV4 (IP Forwarding flag)
Parameter name IP Forwarding flag
Abbreviated name IPForwardingIPV4
3GPP name -
Managed Object IPNO
Parameter group -
Classification -
Multiplicity 1
Description This parameter determines whether the TCP/IP stack forwards unicast IP packets that do not belong to it. If the parameters are configured for the first time, the default value is "OFF" for DMX unit; the default value is "ON" for CHORUS units; other-wise, the current value remains.
The parameter is used for the IPv4 stack configuration.
The corresponding MML command: ZQRT, "IP forwarding".
Range No (0), Yes (1)
Step -
Units -
Formula for getting internal value
gui ==> internal
No ==> 0
Yes ==> 1
Default value -
Default value notes Default value is based on the unit type.
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • RNC <-> RAC • RAC <-> RACApp
References -
Table 114 IPForwardingIPV4 (IP Forwarding flag)
124 DN70257257
IP Configuration Plan Interface Parameters
Id:0900d805808e2b75Confidential
IPNO Parameters
16.2 defaultTTL (Default TTL)
16.3 hostName (Host name)
Parameter name Default TTL
Abbreviated name defaultTTL
3GPP name -
Managed Object IPNO
Parameter group -
Classification -
Multiplicity 1
Description The maximum time-to-live (hop count) value for an IP packet sourced by the system. Values range from zero to 254. The default value is 64 if configured for the first time, otherwise the current value remains.
The parameter is used for the IPv4 stack configuration.
The corresponding MML command group: ZQRT, "IP TTL".
Range 0... 254
Step 1
Units -
Formula for getting internal value
internal_value = gui_value
Default value 64
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • RNC <-> RAC • RAC <-> RACApp
References -
Table 115 defaultTTL (Default TTL)
Parameter name Host name
Abbreviated name hostName
3GPP name -
Table 116 hostName (Host name)
DN70257257 125
IP Configuration Plan Interface Parameters IPNO Parameters
Id:0900d805808e2b75Confidential
16.4 ipNodeId (IP Node Identifier)
Managed Object IPNO
Parameter group -
Classification -
Multiplicity 1
Description The name of the host computer for which you want to create either a fully qualified domain name (FQDN) or a name without the domain part. The name can contain the following characters: letters A-Z, numbers 0-9, and a hyphen (-). The maximum length of the name is 100 characters.
The parameter is used for the IPv4 stack configuration.
The corresponding MML command group: ZQRT, "host name".
Range 1...100
Step -
Units characters
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • RNC <-> RAC • RAC <-> RACApp
References -
Table 116 hostName (Host name) (Cont.)
Parameter name IP Node Identifier
Abbreviated name ipNodeId
3GPP name -
Managed Object IPNO
Parameter group -
Classification -
Multiplicity 1
Table 117 ipNodeId (IP Node Identifier)
126 DN70257257
IP Configuration Plan Interface Parameters
Id:0900d805808e2b75Confidential
IPNO Parameters
16.5 subnetsAreLocal (Subnets are local)
Description This parameter identifies the IP node entity in the system. The identifier is part of the distinguished name and is formed in the following way: NE-x/IPNO-unitType-unitIndex. For example: RNC-1/IPNO-OMU-0.
The corresponding MML command group: ZQRT.
Range 1...32
Step -
Units characters
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes -
Related functions -
Modification Not modifiable
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • RNC <-> RAC • RAC <-> RACApp
References -
Table 117 ipNodeId (IP Node Identifier) (Cont.)
Parameter name Subnets are local
Abbreviated name subnetsAreLocal
3GPP name -
Managed Object IPNO
Parameter group -
Classification -
Multiplicity 1
Description This parameter defines whether subnets are considered to be local addresses. If not, only destination IP addresses on an attached subnetwork are considered local. The default value is 'YES' if parameters are configured for the first time, otherwise the current value remains. This parameter only exists in the DMX unit.
The parameter is used for the IPv4 stack configuration.
The corresponding MML command group: ZQRT, "Subnets are local".
Table 118 subnetsAreLocal (Subnets are local)
DN70257257 127
IP Configuration Plan Interface Parameters IPNO Parameters
Id:0900d805808e2b75Confidential
Range No (0), Yes (1)
Step -
Units -
Formula for getting internal value
gui ==> internal
No ==> 0
Yes ==> 1
Default value Yes (1)
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • RNC <-> RAC • RAC <-> RACApp
References -
Table 118 subnetsAreLocal (Subnets are local) (Cont.)
128 DN70257257
IP Configuration Plan Interface Parameters
Id:0900d805808e2b75Confidential
IPRO Parameters
17 IPRO Parameters
17.1 ipBasedRoute (IP based route Entries)
Parameter name IP based route Entries
Abbreviated name ipBasedRoute
3GPP name -
Managed Object IPRO
Parameter group -
Classification -
Multiplicity 1800
Description Defines the IP based route network.
One unit can supports 1024 IP based routes at most.
The corresponding MML command is ZQRC;
Formula for getting internal value
-
Default value -
Default value notes -
Related functions -
Child parameters • addrValueIPV4 • ipBasedRouteId • phbAF1 • phbAF2 • phbAF3 • phbAF4 • phbBE • phbEF
Modification On-Line
Related parameters iproListMode of IPRO
Parameter relationships The parameter has an effect on how the list is processed in the plan activation.
Related options -
Feature dependencies -
Interfaces • RNC <-> RAC • RAC <-> RACApp
References -
Table 119 ipBasedRoute (IP based route Entries)
DN70257257 129
IP Configuration Plan Interface Parameters IPRO Parameters
Id:0900d805808e2b75Confidential
17.2 addrValueIPV4 (IP address )
17.3 ipBasedRouteId (IP based route id)
Parameter name IP address
Abbreviated name addrValueIPV4
3GPP name -
Managed Object -
Parameter group -
Classification -
Multiplicity 1
Description This parameter defines the IP address which is attached to the IP based route. The address is specified in the conventional dot notation (#.#.#.#).
The corresponding MML command group: ZQRC,"IP address".
Range 7...15
Step -
Units characters
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes -
Related functions -
Modification Not modifiable
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • RAC <-> RNC • RAC <-> RACApp
References -
Table 120 addrValueIPV4 (IP address )
Parameter name IP based route id
Abbreviated name ipBasedRouteId
3GPP name -
Managed Object -
Table 121 ipBasedRouteId (IP based route id)
130 DN70257257
IP Configuration Plan Interface Parameters
Id:0900d805808e2b75Confidential
IPRO Parameters
17.4 phbAF1 (PHB AF1)
Parameter group -
Classification -
Multiplicity 1
Description This parameter defines the IP based route to which this interface is attached.
The corresponding MML command group: ZQRC, "IP based route id".
Range 1... 4095
Step 1
Units -
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes Defualt value is not possible
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • RNC <-> RAC • RAC <-> RACApp
References -
Table 121 ipBasedRouteId (IP based route id) (Cont.)
Parameter name PHB AF1
Abbreviated name phbAF1
3GPP name -
Managed Object -
Parameter group -
Classification -
Multiplicity 1
Table 122 phbAF1 (PHB AF1)
DN70257257 131
IP Configuration Plan Interface Parameters IPRO Parameters
Id:0900d805808e2b75Confidential
17.5 phbAF2 (PHB AF2)
Description PHB set is attached to the IP based route for VLAN traffic differentiation, and takes effect in VLAN configured site. Only the traffic whose type is within the PHB set will run on the specified IP based route. For example: "EF,AF4" is attached to IP based route "ipbr_1", "AF1,BE" is attached to IP based route "ipbr_2", then "voice" traffic will run on "ipbr_1" and BE traffic will run on "ipbr_2".
Note: PHB set is the combination of one or more of the PHB value. For example: "AF4, AF3, EF" or "AF1, BE".
This parameter determines whether PHB value "AF1" is available in the PHB set of the IP based route. The value of this parameter is "true" if PHB value "AF1" is avail-able in the PHB set, else "false". The corresponding MML command group: ZQRC,"PHBSet".
Range false (0), true (1)
Step -
Units -
Formula for getting internal value
• false => 0 • true => 1
Default value true (1)
Default value notes All PHB value("BE","AF4","AF3","AF2","AF1","EF") are available for the PHB set of the IP based route in default.
Related functions -
Modification On-Line
Related parameters phbBE of IPRO
phbAF4 of IPRO
phbAF3 of IPRO
phbAF2 of IPRO
phbEF of IPRO
Parameter relationships phbAF1 can not be set to "false" if phbBE,phbAF2,phbAF3,phbAF4 and phbEF are all set as "false". In other words, at least one of phbBE,phbAF1,phbAF2,phbAF3,phbAF4 and phbEF should be set to "true".
Related options -
Feature dependencies -
Interfaces • RNC <-> RAC • RAC <-> RACApp
References -
Table 122 phbAF1 (PHB AF1) (Cont.)
Parameter name PHB AF2
Table 123 phbAF2 (PHB AF2)
132 DN70257257
IP Configuration Plan Interface Parameters
Id:0900d805808e2b75Confidential
IPRO Parameters
Abbreviated name phbAF2
3GPP name -
Managed Object -
Parameter group -
Classification -
Multiplicity 1
Description PHB set is attached to IP based route for VLAN traffic differentiation, and takes effect in VLAN configured site. Only the traffic whose type is within the PHB set will run on the specified IP based route. For example: "EF,AF4" is attached to IP based route "ipbr_1", "AF1,BE" is attached to IP based route "ipbr_2", then "voice" traffic will run on "ipbr_1" and BE traffic will run on "ipbr_2".
Note: PHB set is the combination of one or more of the PHB value. For example: "AF4, AF3, EF" or "AF1, BE".
This parameter determines whether PHB value "AF2" is available in the PHB set of the IP based route. Value of this parameter is "true" if PHB value "AF2" is available in the PHB set, else "false". The corresponding MML command group: ZQRC,"PHBSet".
Range false (0), true (1)
Step -
Units -
Formula for getting internal value
• false => 0 • true => 1
Default value true (1)
Default value notes All PHB value("BE","AF4","AF3","AF2","AF1","EF") are available for the PHB set of the IP based route in default.
Related functions -
Modification On-Line
Related parameters phbBE of IPRO
phbAF4 of IPRO
phbAF3 of IPRO
phbAF1 of IPRO
phbEF of IPRO
Parameter relationships phbAF2 can not be set to "false" if phbBE,phbAF1,phbAF3,phbAF4 and phbEF are all set as "false". In other words, at least one of phbBE,phbAF1,phbAF2,phbAF3,phbAF4 and phbEF should be set to "true".
Related options -
Feature dependencies -
Interfaces • RNC <-> RAC • RAC <-> RACApp
Table 123 phbAF2 (PHB AF2) (Cont.)
DN70257257 133
IP Configuration Plan Interface Parameters IPRO Parameters
Id:0900d805808e2b75Confidential
17.6 phbAF3 (PHB AF3)
References -
Table 123 phbAF2 (PHB AF2) (Cont.)
Parameter name PHB AF3
Abbreviated name phbAF3
3GPP name -
Managed Object -
Parameter group -
Classification -
Multiplicity 1
Description PHB set is attached to IP based route for VLAN traffic differentiation, and takes effect in VLAN configured site. Only the traffic whose type is within the PHB set will run on the specified IP based route. For example: "EF,AF4" is attached to IP based route "ipbr_1", "AF1,BE" is attached to IP based route "ipbr_2", then "voice" traffic will run on "ipbr_1" and BE traffic will run on "ipbr_2".
Note: PHB set is the combination of one or more of the PHB value. For example: "AF4, AF3, EF" or "AF1, BE".
This parameter determines whether PHB value "AF3" is available in the PHB set of the IP based route. The value of this parameter is "true" if PHB value "AF3" is avail-able in the PHB set, else "false". The corresponding MML command group: ZQRC,"PHBSet".
Range false (0), true (1)
Step -
Units -
Formula for getting internal value
• false => 0 • true => 1
Default value true (1)
Default value notes All PHB value("BE","AF4","AF3","AF2","AF1","EF") are available for the PHB set of the IP based route in default.
Related functions -
Modification On-Line
Related parameters phbBE of IPRO
phbAF4 of IPRO
phbAF2 of IPRO
phbAF1 of IPRO
phbEF of IPRO
Table 124 phbAF3 (PHB AF3)
134 DN70257257
IP Configuration Plan Interface Parameters
Id:0900d805808e2b75Confidential
IPRO Parameters
17.7 phbAF4 (PHB AF4)
Parameter relationships phbAF3 can not be set to "false" if phbBE,phbAF1,phbAF2,phbAF4 and phbEF are all set as "false". In other words, at least one of phbBE,phbAF1,phbAF2,phbAF3,phbAF4 and phbEF should be set to "true".
Related options -
Feature dependencies -
Interfaces • RNC <-> RAC • RAC <-> RACApp
References -
Table 124 phbAF3 (PHB AF3) (Cont.)
Parameter name PHB AF4
Abbreviated name phbAF4
3GPP name -
Managed Object -
Parameter group -
Classification -
Multiplicity 1
Description PHB set is attached to IP based route for VLAN traffic differentiation, and takes effect in VLAN configured site. Only the traffic whose type is within the PHB set will run on the specified IP based route. For example: "EF,AF4" is attached to IP based route "ipbr_1", "AF1,BE" is attached to IP based route "ipbr_2", then "voice" traffic will run on "ipbr_1" and BE traffic will run on "ipbr_2".
Note: PHB set is the combination of one or more of the PHB value. For example: "AF4, AF3, EF" or "AF1, BE".
This parameter determines whether PHB value "AF4" is available in the PHB set of the IP based route. The value of this parameter is "true" if PHB value "AF4" is avail-able in the PHB set, else "false". The corresponding MML command group: ZQRC,"PHBSet".
Range false (0), true (1)
Step -
Units -
Formula for getting internal value
• false => 0 • true => 1
Default value true (1)
Default value notes All PHB value("BE","AF4","AF3","AF2","AF1","EF") are available for the PHB set of the IP based route in default.
Related functions -
Table 125 phbAF4 (PHB AF4)
DN70257257 135
IP Configuration Plan Interface Parameters IPRO Parameters
Id:0900d805808e2b75Confidential
17.8 phbEF (PHB EF)
Modification On-Line
Related parameters phbBE of IPRO
phbAF3 of IPRO
phbAF2 of IPRO
phbAF1 of IPRO
phbEF of IPRO
Parameter relationships phbAF4 can not be set to "false" if phbBE,phbAF1,phbAF2,phbAF3 and phbEF are all set as "false". In other words, at least one of phbBE,phbAF1,phbAF2,phbAF3,phbAF4 and phbEF should be set to "true".
Related options -
Feature dependencies -
Interfaces • RNC <-> RAC • RAC <-> RACApp
References -
Table 125 phbAF4 (PHB AF4) (Cont.)
Parameter name PHB EF
Abbreviated name phbEF
3GPP name -
Managed Object -
Parameter group -
Classification -
Multiplicity 1
Description PHB set is attached to IP based route for VLAN traffic differentiation, and takes effect in VLAN configured site. Only the traffic whose type is within the PHB set will run on the specified IP based route. For example: "EF,AF4" is attached to IP based route "ipbr_1", "AF1,BE" is attached to IP based route "ipbr_2", then "voice" traffic will run on "ipbr_1" and BE traffic will run on "ipbr_2".
Note: PHB set is the combination of one or more of the PHB value. For example: "AF1, AF3, EF" or "AF2, BE".
This parameter determines whether PHB value "EF" is available in the PHB set of the IP based route. The value of this parameter is "true" if PHB value "EF" is avail-able in the PHB set, else "false". The corresponding MML command group: ZQRC,"PHBSet".
Range false (0), true (1)
Step -
Table 126 phbEF (PHB EF)
136 DN70257257
IP Configuration Plan Interface Parameters
Id:0900d805808e2b75Confidential
IPRO Parameters
17.9 iproId (network interface Identifier)
Units -
Formula for getting internal value
• false => 0 • true => 1
Default value true (1)
Default value notes All PHB value("BE","AF4","AF3","AF2","AF1","EF") are available for the PHB set of the IP based route in default.
Related functions -
Modification On-Line
Related parameters phbBE of IPRO
phbAF4 of IPRO
phbAF3 of IPRO
phbAF2 of IPRO
phbAF1 of IPRO
Parameter relationships phbEF can not be set to "false" if phbBE,phbAF1,phbAF2,phbAF3 and phbAF4 are all set as "false". In other words, at least one of phbBE,phbAF1,phbAF2,phbAF3,phbAF4 and phbEF should be set to "true".
Related options -
Feature dependencies -
Interfaces • RNC <-> RAC • RAC <-> RACApp
References -
Table 126 phbEF (PHB EF) (Cont.)
Parameter name network interface Identifier
Abbreviated name iproId
3GPP name -
Managed Object IPRO
Parameter group -
Classification -
Multiplicity 1
Description This parameter identifies the network interface which configures the IP based route within the IP node entity in the system. The identifier is part of the distinguished name and it is formed in the following way: NE-x/IPNO-unitType-unitIndex/IPRO-ifName. For example: RNC-1/IPNO-NPGEP-0/IPRO-IFGE0.
The corresponding MML command group: ZQRC, "interface name".
Table 127 iproId (network interface Identifier)
DN70257257 137
IP Configuration Plan Interface Parameters IPRO Parameters
Id:0900d805808e2b75Confidential
17.10 iproListMode (IP Based Route id list update mode)
Range 3...8
Step -
Units characters
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes -
Related functions -
Modification Not modifiable
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • RNC <-> RAC • RAC <-> RACApp
References -
Table 127 iproId (network interface Identifier) (Cont.)
Parameter name IP Based Route id list update mode
Abbreviated name iproListMode
3GPP name -
Managed Object IPRO
Parameter group -
Classification -
Multiplicity 1
Table 128 iproListMode (IP Based Route id list update mode)
138 DN70257257
IP Configuration Plan Interface Parameters
Id:0900d805808e2b75Confidential
IPRO Parameters
Description This parameter determines which of the following two modes is used to update the IP-based route id list:
iproListMode:”Full”
The whole list structure is downloaded. This contains all the existing items received at the IP plan upload, as well as new IP-based route id entries. Items that exist in the IP layer configuration, but which are not included in the download plan list, are removed in the plan activation operation.
Note: In this mode, the whole IP-based route list is delivered in the IP plan. Items not included in the list are deleted from the IP layer configuration.
Note: If PHB set is not defined, all PHBs are set to 'true'.
iproListMode:”Add”
Only the new entries in the list structure are delivered, that is, only the newly added IP-based route id and IP address pairs are included in the list. The new items are added into the configuration, while the existing IP layer configuration remains unchanged. If an item to be added already exists in the configuration, there are 2 cases:
1. If PHB set is not defined, the existing item remains unchanged.
2. If PHB set is defined, the PHB set of existed item will be updated.
Note: Deletion of IP-based route id and IP address pairs is only supported in “Full” operation mode. Only one deletion plan at a time is sent and activated with an up-to-date list. All items that are to remain in the IP layer configuration must be included in the list.
The parameter value is not stored in the IP layer configuration; it is only used to determine the mode in which the IPRO-IPBasedRoute list is processed. When the parameter value is not included in the downloaded plan file, the default value (“Full”) is used by the network element. This parameter is not used in IPRO object creation.
Range Full (0), Add (1)
Step -
Units -
Formula for getting internal value
gui ==> internal
Full ==> 0
Add ==> 1
Default value Full (0)
Default value notes In the default mode “Full,” all existing entries that are not to be changed must be found from the list. Items that currently exist in the IP layer configuration, but which are not included in the list, are deleted.
Related functions -
Modification On-Line
Related parameters ipBasedRoute of IPRO
Parameter relationships This parameter detemines the way in which the list is processed in plan activation.
Table 128 iproListMode (IP Based Route id list update mode) (Cont.)
DN70257257 139
IP Configuration Plan Interface Parameters IPRO Parameters
Id:0900d805808e2b75Confidential
Related options -
Feature dependencies -
Interfaces • RAC -> RNC • RACApp -> RAC
References -
Table 128 iproListMode (IP Based Route id list update mode) (Cont.)
140 DN70257257
IP Configuration Plan Interface Parameters
Id:0900d805808e2b75Confidential
IPRT Parameters
18 IPRT Parameters
18.1 ipRoutingTableId (IP Routing Table Identifier)
Parameter name IP Routing Table Identifier
Abbreviated name ipRoutingTableId
3GPP name -
Managed Object IPRT
Parameter group -
Classification -
Multiplicity 1
Description Identifies the IP routing table within the IP node entity in the system. There is only one IPRT within the IPNO.
Only the routing table on working unit is shown as an operational object and when configuring route entries it has to be done for the working unit, not for the spare unit.
The identifier is part of the distinguished name and it is formed in the following way: NE-x/IPNO-unitType-unitIndex/IPRT-1. For example: RNC-1/IPNO-OMU-0/IPRT-1.
The corresponding MML command group: ZQKC, ZQKA, ZQKB.
Range 1... 1
Step 1
Units -
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes -
Related functions -
Modification Not modifiable
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • RNC <-> RAC • RAC <-> RACApp
References -
Table 129 ipRoutingTableId (IP Routing Table Identifier)
DN70257257 141
IP Configuration Plan Interface Parameters IPRT Parameters
Id:0900d805808e2b75Confidential
18.2 iprtListMode (IP static route list update mode)
Parameter name IP static route list update mode
Abbreviated name iprtListMode
3GPP name -
Managed Object IPRT
Parameter group -
Classification -
Multiplicity 1
Description This parameter determines which of the following two modes is used to update the IP static route list:
iprtListMode:”Full”
The whole list structure is downloaded. This contains all the existing items received at the IP plan upload, as well as the new IP static route entries. Items that exist in the IP layer configuration, but which are not included in the download plan list, are removed in the plan activation operation.
Note: In this mode, the whole IP static route list is delivered in the IP plan. Items not included in the list are deleted from the IP layer configuration.
iprtListMode:”Add”
Only the new entries in the list structure are delivered, that is, only the newly added IP static routes are included in the list. The new items are added into the configu-ration, while the existing IP layer configuration remains unchanged. If an item to be added already exists in the configuration, then the existing item remains unchanged.
Note: Deletion of IP static route entries is only supported in ”Full” operation mode. Only one deletion plan at a time is sent and activated with an up-to-date list. All items that are to remain in the IP layer configuration must be included in the list.
The parameter value is not stored in the IP layer configuration; it is only used to determine the mode in which the IPRT- routeEntriesIPV4 list is processed. When the parameter value is not included in the downloaded plan file, the default value (“Full”) is used by the network element. This parameter is not used in IPRT object creation.
Range Full (0), Add (1)
Step -
Units -
Formula for getting internal value
gui ==> internal
Full ==> 0
Add ==> 1
Default value Full (0)
Table 130 iprtListMode (IP static route list update mode)
142 DN70257257
IP Configuration Plan Interface Parameters
Id:0900d805808e2b75Confidential
IPRT Parameters
18.3 routeEntriesIPV4 (Route Entries for IPv4)
Default value notes In the default mode “Full,” all existing entries that are not to be changed must be found from the list. Items that currently exist in the IP layer configuration, but which are not included in the list, are deleted.
Related functions -
Modification On-Line
Related parameters routeEntriesIPV4 of IPRT
Parameter relationships This parameter determines the way in which the list is processed in plan activation.
Related options -
Feature dependencies -
Interfaces • RAC -> RNC • RACApp -> RAC
References -
Table 130 iprtListMode (IP static route list update mode) (Cont.)
Parameter name Route Entries for IPv4
Abbreviated name routeEntriesIPV4
3GPP name -
Managed Object IPRT
Parameter group -
Classification -
Multiplicity 1024
Description Route entries for IPv4. The corresponding MML command group: ZQKC,ZQKG.
For destination address based route:
ZQKC:[<unit_type>,[<unit_index>]]:[<dst_ip_address>,<net-mask>]:[<gateway_ip_address>]: [<route_type>];
For source address based route:
ZQKC:[<unit_type>,[<unit_index>]]::[<gateway_ip_address>,<src_ip_address>,<netmask>]: [<route_type>];
Formula for getting internal value
-
Default value -
Default value notes -
Related functions -
Table 131 routeEntriesIPV4 (Route Entries for IPv4)
DN70257257 143
IP Configuration Plan Interface Parameters IPRT Parameters
Id:0900d805808e2b75Confidential
18.4 bfdId (BFD session ID)
Child parameters • bfdId • destIPAddrIPV4 • gatewayIPV4 • netmask • preference • routeType • srcIPAddrIPV4
Modification On-Line
Related parameters iprtListMode of IPRT
Parameter relationships The parameter has an effect on how the list is processed in the plan activation.
Related options -
Feature dependencies -
Interfaces • RNC <-> RAC • RAC <-> RACApp
References -
Table 131 routeEntriesIPV4 (Route Entries for IPv4) (Cont.)
Parameter name BFD session ID
Abbreviated name bfdId
3GPP name -
Managed Object -
Parameter group -
Classification -
Multiplicity 1
Description This parameter gets/sets the BFD session ID which is bound with the static route. Only the Single-Hop BFD sessions are supported.
If the static is not bound with the BFD session, the parameter will be 0.
The parameter is only valid for the destination address based route.
The corresponding MML command: ZQKG,ZQKB
Range 0... 3000
Step 1
Units -
Formula for getting internal value
internal_value = gui_value
Default value 0
Table 132 bfdId (BFD session ID)
144 DN70257257
IP Configuration Plan Interface Parameters
Id:0900d805808e2b75Confidential
IPRT Parameters
18.5 destIPAddrIPV4 (Destination IPv4 address)
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • RNC <-> RAC • RAC <-> RACApp
References -
Table 132 bfdId (BFD session ID) (Cont.)
Parameter name Destination IPv4 address
Abbreviated name destIPAddrIPV4
3GPP name -
Managed Object -
Parameter group -
Classification -
Multiplicity 1
Description The route's destination IP address or IP subnetwork. The address is specified in the conventional dot notation (#.#.#.#). The parameter range for each part of the address is from zero to 255.
For default static route, destIPAddrIPV4 is (0.0.0.0) and netmask is( 255.255.255.255).
For source based static route, fill correct srcIPAddrIPV4 and netmaks, keep destIPAddrIPV4 (0.0.0.0).
The corresponding MML command: ZQKC, "destination IP address".
Range 7...15
Step -
Units characters
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes -
Related functions -
Table 133 destIPAddrIPV4 (Destination IPv4 address)
DN70257257 145
IP Configuration Plan Interface Parameters IPRT Parameters
Id:0900d805808e2b75Confidential
18.6 gatewayIPV4 (Gateway IPv4 address)
Modification On-Line
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • RNC <-> RAC • RAC <-> RACApp
References -
Table 133 destIPAddrIPV4 (Destination IPv4 address) (Cont.)
Parameter name Gateway IPv4 address
Abbreviated name gatewayIPV4
3GPP name -
Managed Object -
Parameter group -
Classification -
Multiplicity 1
Description The IP address of the gateway. The address is specified in the conventional dot notation (#.#.#.#). The parameter range for each part of the address is from zero to 255. This parameter is obligatory.
The corresponding MML command group: ZQKC, "gateway IP address".
Range 7...15
Step -
Units characters
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Table 134 gatewayIPV4 (Gateway IPv4 address)
146 DN70257257
IP Configuration Plan Interface Parameters
Id:0900d805808e2b75Confidential
IPRT Parameters
18.7 netmask (Netmask)
Interfaces • RNC <-> RAC • RAC <-> RACApp
References -
Table 134 gatewayIPV4 (Gateway IPv4 address) (Cont.)
Parameter name Netmask
Abbreviated name netmask
3GPP name -
Managed Object -
Parameter group -
Classification -
Multiplicity 1
Description Netmask used for the static route.
For the destination based route, it is the netmask of destIPAddrIPV4.
For the source based route, it is the netmask of srcIPAddrIPV4.
For the default static route, netmask is (255.255.255.255) and keep destIPAddrIPV4 as (0.0.0.0).
The corresponding MML command group: ZQKC, "netmask".
Range 7...15
Step -
Units characters
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • RNC <-> RAC • RAC <-> RACApp
References -
Table 135 netmask (Netmask)
DN70257257 147
IP Configuration Plan Interface Parameters IPRT Parameters
Id:0900d805808e2b75Confidential
18.8 preference (Preference)
18.9 routeType (Route type)
Parameter name Preference
Abbreviated name preference
3GPP name -
Managed Object -
Parameter group -
Classification -
Multiplicity 1
Description Router preference is used to configure different route priority.
Only destination address based route is supported.
The corresponding MML command: ZQKC,ZQKB
Range 0... 255
Step 1
Units -
Formula for getting internal value
internal_value = gui_value
Default value 0
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • RNC <-> RAC • RAC <-> RACApp
References -
Table 136 preference (Preference)
Parameter name Route type
Abbreviated name routeType
3GPP name -
Managed Object -
Table 137 routeType (Route type)
148 DN70257257
IP Configuration Plan Interface Parameters
Id:0900d805808e2b75Confidential
IPRT Parameters
18.10 srcIPAddrIPV4 (Source IPv4 address)
Parameter group -
Classification -
Multiplicity 1
Description The route type for the static route to be created.
Physical: A route that uses a physical address to reach its gateway. A physical route is always present in the unit it is configured.
Logical: A route that uses a logical address to reach its gateway. The route follows the logical address if a switchover occurs.
The corresponding MML command group: ZQKC, "route type".
Range Physical (0), Logical (1)
Step -
Units -
Formula for getting internal value
gui ==> internal
Physical ==> 0
Logical ==> 1
Default value -
Default value notes For NPGE, Default value is Physical (0).For NPGEP,Default value is Logical (1).
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • RNC <-> RAC • RAC <-> RACApp
References -
Table 137 routeType (Route type) (Cont.)
Parameter name Source IPv4 address
Abbreviated name srcIPAddrIPV4
3GPP name -
Managed Object -
Parameter group -
Classification -
Table 138 srcIPAddrIPV4 (Source IPv4 address)
DN70257257 149
IP Configuration Plan Interface Parameters IPRT Parameters
Id:0900d805808e2b75Confidential
Multiplicity 1
Description The route's source IP address or IP subnetwork. The address is specified in the conventional dot notation (#.#.#.#). The parameter range for each part of the address is from zero to 255.
For the default static route, destIPAddrIPV4 is (0.0.0.0), netmask is( 255.255.255.255), and keep srcIPAddrIPV4 blank.
For the destination based static route, destIPAddrIPV4 is like(X.X.X.X), netmask is like (255.255.x.x) and keep srcIPAddrIPV4 blank.
For the source based static route, srcIPAddrIPV4 is like(X.X.X.X), netmask is like (255.255.x.x) and keep destIPAddrIPV4 as (0.0.0.0).
Range 7...15
Step -
Units characters
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • RNC <-> RAC • RAC <-> RACApp
References -
Table 138 srcIPAddrIPV4 (Source IPv4 address) (Cont.)
150 DN70257257
IP Configuration Plan Interface Parameters
Id:0900d805808e2b75Confidential
IQOS Parameters
19 IQOS Parameters
19.1 dspmProfileId (DSPM profile id)
19.2 dspmProfileName (DSPM profile name)
Parameter name DSPM profile id
Abbreviated name dspmProfileId
3GPP name -
Managed Object IQOS
Parameter group -
Classification -
Multiplicity 1
Description This parameter defines the DSPM profile to which the interface is attached.
The corresponding MML command: ZQ8S, "dspm profile id".
Range 0... 10
Step 1
Units -
Formula for getting internal value
internal_value = gui_value
Default value 0
Default value notes The default id is the former configured id for the interface otherwise default id is 0.
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • RAC <-> RNC • RACApp <-> RAC
References -
Table 139 dspmProfileId (DSPM profile id)
Parameter name DSPM profile name
Abbreviated name dspmProfileName
3GPP name -
Table 140 dspmProfileName (DSPM profile name)
DN70257257 151
IP Configuration Plan Interface Parameters IQOS Parameters
Id:0900d805808e2b75Confidential
19.3 iqosId (Qos interface)
Managed Object IQOS
Parameter group -
Classification -
Multiplicity 1
Description This parameter defines the DSPM profile to which the interface is attached.
The corresponding MML command: ZQ8S, "dspm profile name".
Range 1...20
Step -
Units characters
Formula for getting internal value
internal_value = gui_value
Default value DEFAULT
Default value notes The default name is the former configured name for the interface otherwise default id is "DEFAULT".
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • RAC <-> RNC • RACApp <-> RAC
References -
Table 140 dspmProfileName (DSPM profile name) (Cont.)
Parameter name Qos interface
Abbreviated name iqosId
3GPP name -
Managed Object IQOS
Parameter group -
Classification -
Multiplicity 1
Table 141 iqosId (Qos interface)
152 DN70257257
IP Configuration Plan Interface Parameters
Id:0900d805808e2b75Confidential
IQOS Parameters
19.4 phbProfileId (PHB profile id)
Description This parameter identifies the Ethernet interface which is used for the QoS configu-ration in the system. The identifier is part of the distinguished name and it is formed in the following way: NE-x/IPNO-unitType-unitIndex/IQOS-ifName. For example: RNC-1/IPNO-NPGEP-0/IQOS-IFGE0.
The corresponding MML command: ZQ8S,"interface name".
Range 3...8
Step -
Units characters
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes -
Related functions -
Modification Not modifiable
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • RAC <-> RNC • RACApp <-> RAC
References -
Table 141 iqosId (Qos interface) (Cont.)
Parameter name PHB profile id
Abbreviated name phbProfileId
3GPP name -
Managed Object IQOS
Parameter group -
Classification -
Multiplicity 1
Description This parameter defines the phb profile to which the interface is attached.
The corresponding MML command: ZQ8S, "phb profile id".
Range 0... 10
Step 1
Units -
Table 142 phbProfileId (PHB profile id)
DN70257257 153
IP Configuration Plan Interface Parameters IQOS Parameters
Id:0900d805808e2b75Confidential
19.5 phbProfileName (PHB profile name)
Formula for getting internal value
internal_value = gui_value
Default value 0
Default value notes The default id is the former configured id for the interface otherwise default id is 0.
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • RAC <-> RNC • RACApp <-> RAC
References -
Table 142 phbProfileId (PHB profile id) (Cont.)
Parameter name PHB profile name
Abbreviated name phbProfileName
3GPP name -
Managed Object IQOS
Parameter group -
Classification -
Multiplicity 1
Description This parameter defines the name of the phb profile to which the interface is attached.
The corresponding MML command: ZQ8S, "phb profile name".
Range 1...20
Step -
Units characters
Formula for getting internal value
internal_value = gui_value
Default value DEFAULT
Default value notes The default name is the former configured name for the interface otherwise default id is "DEFAULT".
Related functions -
Modification On-Line
Table 143 phbProfileName (PHB profile name)
154 DN70257257
IP Configuration Plan Interface Parameters
Id:0900d805808e2b75Confidential
IQOS Parameters
19.6 status (Status)
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • RAC <-> RNC • RACApp <-> RAC
References -
Table 143 phbProfileName (PHB profile name) (Cont.)
Parameter name Status
Abbreviated name status
3GPP name -
Managed Object IQOS
Parameter group -
Classification -
Multiplicity 1
Description This parameter defines the diffServ configuration for the IP interface.
DiffServ Disable for IP interface means that all the traffic to or from the interface is treated as BE traffic.
The corresponding MML command group: ZQ8S, "enable or disable".
Range Disable (0), Enable (1)
Step -
Units -
Formula for getting internal value
gui ==> internal
Disable ==> 0
Enable ==> 1
Default value Enable (1)
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Table 144 status (Status)
DN70257257 155
IP Configuration Plan Interface Parameters IQOS Parameters
Id:0900d805808e2b75Confidential
Interfaces • RAC <-> RNC • RACApp <-> RAC
References -
Table 144 status (Status) (Cont.)
156 DN70257257
IP Configuration Plan Interface Parameters
Id:0900d805808e2b75Confidential
ISBFP Parameters
20 ISBFP Parameters
20.1 desiredMinTx (Min transmission interval)
20.2 detectMult (Detection multiplier)
Parameter name Min transmission interval
Abbreviated name desiredMinTx
3GPP name -
Managed Object ISBFP
Parameter group -
Classification -
Multiplicity 1
Description This parameter defines the minimum interval between two transmitted control packets.
The corresponding MML command : ZYGP,"minimum TX interval".
Range 50... 5000
Step 50
Units -
Formula for getting internal value
internal_value = gui_value
Default value 250
Default value notes The unit is milliseconds.
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • RNC <-> RAC • RAC <-> RACApp
References -
Table 145 desiredMinTx (Min transmission interval)
Parameter name Detection multiplier
Abbreviated name detectMult
Table 146 detectMult (Detection multiplier)
DN70257257 157
IP Configuration Plan Interface Parameters ISBFP Parameters
Id:0900d805808e2b75Confidential
20.3 dscp (DSCP)
3GPP name -
Managed Object ISBFP
Parameter group -
Classification -
Multiplicity 1
Description This parameter indicates the number of control packets that the RNC will lose before the BFD session is declared down.
The corresponding MML command group: ZYGP, "detect multi".
Range 2... 10
Step 1
Units -
Formula for getting internal value
internal_value = gui_value
Default value 5
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • RNC <-> RAC • RAC <-> RACApp
References -
Table 146 detectMult (Detection multiplier) (Cont.)
Parameter name DSCP
Abbreviated name dscp
3GPP name -
Managed Object ISBFP
Parameter group -
Classification -
Multiplicity 1
Table 147 dscp (DSCP)
158 DN70257257
IP Configuration Plan Interface Parameters
Id:0900d805808e2b75Confidential
ISBFP Parameters
20.4 holdupTime (Holdup Time)
Description This parameter defines the DSCP value.
The corresponding MML command: ZYGP.
Range 0... 63
Step 1
Units -
Formula for getting internal value
internal_value = gui_value
Default value 48
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • RNC <-> RAC • RAC <-> RACApp
References -
Table 147 dscp (DSCP) (Cont.)
Parameter name Holdup Time
Abbreviated name holdupTime
3GPP name -
Managed Object ISBFP
Parameter group -
Classification -
Multiplicity 1
Description After BFD session state changes to UP, the subscribed service, such as static route, will be affected after Holdup Time.
The corresponding MML command: ZYGP.
Range 0... 900
Step 1
Units -
Table 148 holdupTime (Holdup Time)
DN70257257 159
IP Configuration Plan Interface Parameters ISBFP Parameters
Id:0900d805808e2b75Confidential
20.5 profileId (ISBFP identifier)
Formula for getting internal value
internal_value = gui_value
Default value 0
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • RNC <-> RAC • RAC <-> RACApp
References -
Table 148 holdupTime (Holdup Time) (Cont.)
Parameter name ISBFP identifier
Abbreviated name profileId
3GPP name -
Managed Object ISBFP
Parameter group -
Classification -
Multiplicity 1
Description This parameter defines the Single-hop BFD profile in the system. The default profile with the profile id "0" cannot be udpated or deleted. It exists only in the upload file and is returned for planning purposes. The identifier is part of the distin-guished name and it is formed in the following way: NE-x/IBFP-profileId. For example: RNC-02/ISBFP-1.
The corresponding MML command group: ZYGP, "profile id".
Range 0... 7
Step 1
Units -
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes -
Table 149 profileId (ISBFP identifier)
160 DN70257257
IP Configuration Plan Interface Parameters
Id:0900d805808e2b75Confidential
ISBFP Parameters
20.6 profileName (Single-hop BFD Profile Name)
Related functions -
Modification Not modifiable
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • RNC <-> RAC • RAC <-> RACApp
References -
Table 149 profileId (ISBFP identifier) (Cont.)
Parameter name Single-hop BFD Profile Name
Abbreviated name profileName
3GPP name -
Managed Object ISBFP
Parameter group -
Classification -
Multiplicity 1
Description This parameter defines the name of the single-hop BFD profile.
The different profiles can use the same name.
MML command ZYGP is used in the Single-Hop profile.
Range 1...10
Step -
Units characters
Formula for getting internal value
internal_value = gui_value
Default value UNDEFINED
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Table 150 profileName (Single-hop BFD Profile Name)
DN70257257 161
IP Configuration Plan Interface Parameters ISBFP Parameters
Id:0900d805808e2b75Confidential
20.7 requiredMinRx (Required minimum reception interval)
Interfaces • RNC <-> RAC • RAC <-> RACApp
References -
Table 150 profileName (Single-hop BFD Profile Name) (Cont.)
Parameter name Required minimum reception interval
Abbreviated name requiredMinRx
3GPP name -
Managed Object ISBFP
Parameter group -
Classification -
Multiplicity 1
Description This parameter defines the minimum required interval between two received control packets.
The corresponding MML command: ZYGP,"minimum RX interval".
Range 50... 5000
Step 50
Units -
Formula for getting internal value
internal_value = gui_value
Default value 250
Default value notes The unit is milliseconds.
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • RNC <-> RAC • RAC <-> RACApp
References -
Table 151 requiredMinRx (Required minimum reception interval)
162 DN70257257
IP Configuration Plan Interface Parameters
Id:0900d805808e2b75Confidential
ISPF Parameters
21 ISPF Parameters
21.1 areaId (Area Identification)
21.2 interfaceEntries (Interface Entries)
Parameter name Area Identification
Abbreviated name areaId
3GPP name -
Managed Object ISPF
Parameter group -
Classification -
Multiplicity 1
Description The area ID for a new OSPF area.
The area ID is given as a dotted quad, for example, [0-255].[0-255].[0-255].[0-255]. The area ID of 0.0.0.0 is reserved for the backbone. The IP network number of a subnetwork can be used as the area ID. The corresponding MML command : ZQKE, "area identification".
Range 7...15
Step -
Units characters
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes -
Related functions -
Modification Not modifiable
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • RAC <-> RNC • RACApp <-> RAC
References -
Table 152 areaId (Area Identification)
Parameter name Interface Entries
Table 153 interfaceEntries (Interface Entries)
DN70257257 163
IP Configuration Plan Interface Parameters ISPF Parameters
Id:0900d805808e2b75Confidential
21.3 cost (Cost)
Abbreviated name interfaceEntries
3GPP name -
Managed Object ISPF
Parameter group -
Classification -
Multiplicity 1500
Description Defines the OSPF interface list.
Formula for getting internal value
-
Default value -
Default value notes -
Related functions -
Child parameters • cost • deadInterval • helloInterval • interfaceName • passive • password • priority • type
Modification On-Line
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • RAC <-> RNC • RACApp <-> RAC
References -
Table 153 interfaceEntries (Interface Entries) (Cont.)
Parameter name Cost
Abbreviated name cost
3GPP name -
Managed Object -
Parameter group -
Table 154 cost (Cost)
164 DN70257257
IP Configuration Plan Interface Parameters
Id:0900d805808e2b75Confidential
ISPF Parameters
21.4 deadInterval (Dead Interval)
Classification -
Multiplicity 1
Description The weight of a given path in a route. The higher the cost, the less preferred the link. You can explicitly override this in route redistribution. For example, to use one interface over another for routing paths, give one a higher cost. The corresponding MML command group: ZQKF, "ospf cost".
Range 1... 65535
Step 1
Units -
Formula for getting internal value
internal_value = gui_value
Default value 1
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • RAC <-> RNC • RACApp <-> RAC
References -
Table 154 cost (Cost) (Cont.)
Parameter name Dead Interval
Abbreviated name deadInterval
3GPP name -
Managed Object -
Parameter group -
Classification -
Multiplicity 1
Table 155 deadInterval (Dead Interval)
DN70257257 165
IP Configuration Plan Interface Parameters ISPF Parameters
Id:0900d805808e2b75Confidential
21.5 helloInterval (Hello Interval)
Description The length of being unable to hear a router's hello packets before the router declares that the neighbour is down.
The length is given in seconds. Typically, the value of this field must be four times the size of the hello interval. For a given link, this field must be the same on all routers, otherwise adjacencies are not formed. The corresponding MML command group: ZQKF, "router dead interval".
Range 1... 65535
Step 1
Units -
Formula for getting internal value
internal_value = gui_value
Default value 40
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • RAC <-> RNC • RACApp <-> RAC
References -
Table 155 deadInterval (Dead Interval) (Cont.)
Parameter name Hello Interval
Abbreviated name helloInterval
3GPP name -
Managed Object -
Parameter group -
Classification -
Multiplicity 1
Description The length between hello packets sent by the router on the interface. The length is given in seconds. For a given link, this field must be the same on all routers, other-wise adjacencies are not formed. The corresponding MML command group: ZQKF, "hello interval".
Range 1... 65535
Table 156 helloInterval (Hello Interval)
166 DN70257257
IP Configuration Plan Interface Parameters
Id:0900d805808e2b75Confidential
ISPF Parameters
21.6 interfaceName (Interface Name)
Step 1
Units -
Formula for getting internal value
internal_value = gui_value
Default value 10
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • RAC <-> RNC • RACApp <-> RAC
References -
Table 156 helloInterval (Hello Interval) (Cont.)
Parameter name Interface Name
Abbreviated name interfaceName
3GPP name -
Managed Object -
Parameter group -
Classification -
Multiplicity 1
Description This parameter defines the name of the interface, given as a character string of maximum 8 characters. Only attached interfaces can be used. The corresponding MML command: ZQKF, "interface identification".
Range 3...8
Step -
Units characters
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes -
Table 157 interfaceName (Interface Name)
DN70257257 167
IP Configuration Plan Interface Parameters ISPF Parameters
Id:0900d805808e2b75Confidential
21.7 passive (Passive)
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • RAC <-> RNC • RACApp <-> RAC
References -
Table 157 interfaceName (Interface Name) (Cont.)
Parameter name Passive
Abbreviated name passive
3GPP name -
Managed Object -
Parameter group -
Classification -
Multiplicity 1
Description An interface that is put into passive mode will not send hello packets out of the given interface. This means no adjacencies will be formed on the link. The purpose of this mode is to enable the network associated with the interface to be included in the intra-area route calculation as opposed to redistributing the network into OSPF and having it as an ASE. In the passive mode, all interface configuration information, with the exception of the associated area and the cost, are ignored.
Y = Suppress hello packets.
N = Do not suppress hello packets.
The corresponding MML command: ZQKF, "passive".
Range No suppress mode (0), Suppress mode (1)
Step -
Units -
Formula for getting internal value
gui ==> internal
No suppress mode ==> 0
Suppress mode ==> 1
Default value No suppress mode (0)
Default value notes -
Table 158 passive (Passive)
168 DN70257257
IP Configuration Plan Interface Parameters
Id:0900d805808e2b75Confidential
ISPF Parameters
21.8 password (Password)
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • RAC <-> RNC • RACApp <-> RAC
References -
Table 158 passive (Passive) (Cont.)
Parameter name Password
Abbreviated name password
3GPP name -
Managed Object -
Parameter group -
Classification -
Multiplicity 1
Description If you set the authentication type to SIMPLE, a password is required. If it is SIMPLE, the password is an American Standard Code for Information Interchange (ASCII) string of 1 to 8 characters.
The password is to be given inside quotes. The corresponding MML command group: ZQKF, "password".
Range 1...8
Step -
Units characters
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options -
Table 159 password (Password)
DN70257257 169
IP Configuration Plan Interface Parameters ISPF Parameters
Id:0900d805808e2b75Confidential
21.9 priority (Priority)
Feature dependencies -
Interfaces • RAC <-> RNC • RACApp <-> RAC
References -
Table 159 password (Password) (Cont.)
Parameter name Priority
Abbreviated name priority
3GPP name -
Managed Object -
Parameter group -
Classification -
Multiplicity 1
Description The priority for becoming the Designated Router (DR) on this link.
When two routers are attached to a network and both attempt to become a desig-nated router, the one with the highest priority wins. If there is currently an elected DR on the link, it remains the DR regardless of the configured priority. This is to prevent changing the DR too often. This field is relevant only on a shared-media interface (Ethernet), as a DR is not elected on point-to-point type interfaces. A router with 0 priority is not eligible to become the DR. The corresponding MML command group: ZQKF, "election priority".
Range 0... 255
Step 1
Units -
Formula for getting internal value
internal_value = gui_value
Default value 0
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Table 160 priority (Priority)
170 DN70257257
IP Configuration Plan Interface Parameters
Id:0900d805808e2b75Confidential
ISPF Parameters
21.10 type (Type)
Interfaces • RAC <-> RNC • RACApp <-> RAC
References -
Table 160 priority (Priority) (Cont.)
Parameter name Type
Abbreviated name type
3GPP name -
Managed Object -
Parameter group -
Classification -
Multiplicity 1
Description The type of authentication scheme to use for a given OSPF interface. Routers on a given link must agree on the authentication configuration in order to form neigh-bour adjacencies. This is used to guarantee that routing information is accepted only from trusted routers.
NONE = No authentitacion used.
SIMPLE = Simple password authentication.
The corresponding MML command group: ZQKF, "authentication".
Range NONE (0), SIMPLE (1)
Step -
Units -
Formula for getting internal value
gui ==> internal
NONE ==> 0
SIMPLE ==> 1
Default value NONE (0)
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • RAC <-> RNC • RACApp <-> RAC
Table 161 type (Type)
DN70257257 171
IP Configuration Plan Interface Parameters ISPF Parameters
Id:0900d805808e2b75Confidential
21.11 ispfId (ISPF Identifier)
21.12 networkPrefixEntries (Network Prefix Entries)
References -
Table 161 type (Type) (Cont.)
Parameter name ISPF Identifier
Abbreviated name ispfId
3GPP name -
Managed Object ISPF
Parameter group -
Classification -
Multiplicity 1
Description Identifies the OSPF configuration entity related to the IPNO in the system. The identifier is part of the distinguished name and it is formed in the following way: NE-x/IPNO-unitType-unitIndex/ISPF-x. For example: RNC-1/IPNO-OMU-0/ISPF-1. The corresponding MML command group: ZQKE.
Range 0... 65535
Step 1
Units -
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes -
Related functions -
Modification Not modifiable
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • RNC -> RAC • RAC <-> RACApp
References -
Table 162 ispfId (ISPF Identifier)
Parameter name Network Prefix Entries
Table 163 networkPrefixEntries (Network Prefix Entries)
172 DN70257257
IP Configuration Plan Interface Parameters
Id:0900d805808e2b75Confidential
ISPF Parameters
21.13 maskLength (Mask Length)
Abbreviated name networkPrefixEntries
3GPP name -
Managed Object ISPF
Parameter group -
Classification -
Multiplicity 8
Description Defines the network prefix list to an OSPF area.
Formula for getting internal value
-
Default value -
Default value notes -
Related functions -
Child parameters • maskLength • networkPrefix • restriction
Modification On-Line
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • RAC <-> RNC • RACApp <-> RAC
References -
Table 163 networkPrefixEntries (Network Prefix Entries) (Cont.)
Parameter name Mask Length
Abbreviated name maskLength
3GPP name -
Managed Object -
Parameter group -
Classification -
Multiplicity 1
Description The mask length of the advertised address range. The corresponding MML command: ZQKH, "network prefix mask length".
Table 164 maskLength (Mask Length)
DN70257257 173
IP Configuration Plan Interface Parameters ISPF Parameters
Id:0900d805808e2b75Confidential
21.14 networkPrefix (Network Prefix)
Range 1... 32
Step 1
Units -
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • RAC <-> RNC • RACApp <-> RAC
References -
Table 164 maskLength (Mask Length) (Cont.)
Parameter name Network Prefix
Abbreviated name networkPrefix
3GPP name -
Managed Object -
Parameter group -
Classification -
Multiplicity 1
Description Any area can be configured with multiple address ranges. These ranges are used to potentially reduce the number of routing entries that a given area emits into the backbone, and this way all areas. If a given prefix aggregates a number of more specific prefixes within an area, an address range can be configured and is the only prefix advertised into the backbone. Configure an address range that covers parts of a prefix that are not contained within the area with care.
Give the value as a dotted quad, for example '[0-255].[0-255].[0-255].[0-255]'. If you do not give a router ID, the router selects internally the highest interface address at the time of OSPF being enabled. The corresponding MML command group: ZQKH, "network prefix".
Range 7...15
Table 165 networkPrefix (Network Prefix)
174 DN70257257
IP Configuration Plan Interface Parameters
Id:0900d805808e2b75Confidential
ISPF Parameters
21.15 restriction (Restriction)
Step -
Units characters
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • RAC <-> RNC • RACApp <-> RAC
References -
Table 165 networkPrefix (Network Prefix) (Cont.)
Parameter name Restriction
Abbreviated name restriction
3GPP name -
Managed Object -
Parameter group -
Classification -
Multiplicity 1
Description If an address range has marked restrict, no advertisement is injected into the back-bone. The default value is Yes (advertised).
Yes = Summary LSAs are advertised.
No = No summary LSAs are advertised.
The corresponding MML command group: ZQKH, "network prefix restriction".
Range No (0), Yes (1)
Step -
Units -
Table 166 restriction (Restriction)
DN70257257 175
IP Configuration Plan Interface Parameters ISPF Parameters
Id:0900d805808e2b75Confidential
21.16 networkStubEntries (Network Stub Entries)
Formula for getting internal value
gui ==> internal
No ==> 0
Yes ==> 1
Default value Yes (1)
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • RAC <-> RNC • RACApp <-> RAC
References -
Table 166 restriction (Restriction) (Cont.)
Parameter name Network Stub Entries
Abbreviated name networkStubEntries
3GPP name -
Managed Object ISPF
Parameter group -
Classification -
Multiplicity 8
Description Defines the stub network list to an OSPF area.
Formula for getting internal value
-
Default value -
Default value notes -
Related functions -
Child parameters • cost • stubNetwork • stubPrefixLength
Modification On-Line
Related parameters -
Table 167 networkStubEntries (Network Stub Entries)
176 DN70257257
IP Configuration Plan Interface Parameters
Id:0900d805808e2b75Confidential
ISPF Parameters
21.17 cost (Cost)
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • RNC <-> RAC • RAC <-> RACApp
References -
Table 167 networkStubEntries (Network Stub Entries) (Cont.)
Parameter name Cost
Abbreviated name cost
3GPP name -
Managed Object -
Parameter group -
Classification -
Multiplicity 1
Description The cost that the stub network must be advertised with. The corresponding MML command group: ZQKJ, "stub network cost".
Range 1... 65535
Step 1
Units -
Formula for getting internal value
internal_value = gui_value
Default value 1
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • RAC <-> RNC • RACApp <-> RAC
References -
Table 168 cost (Cost)
DN70257257 177
IP Configuration Plan Interface Parameters ISPF Parameters
Id:0900d805808e2b75Confidential
21.18 stubNetwork (Stub Network)
21.19 stubPrefixLength (stub netmask )
Parameter name Stub Network
Abbreviated name stubNetwork
3GPP name -
Managed Object -
Parameter group -
Classification -
Multiplicity 1
Description The OSPF can advertise reachability to addresses that are not running the OSPF to indicate reachability. This can include remote addresses of point-to-point links or additional addresses configured on the router that are not directly running OSPF. Give the stub host as dotted quad, for example, '[0-255].[0-255].[0-255].[0-255]'. The corresponding MML command group: ZQKJ, "stub host".
Range 7...15
Step -
Units characters
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • RAC <-> RNC • RACApp <-> RAC
References -
Table 169 stubNetwork (Stub Network)
Parameter name stub netmask
Abbreviated name stubPrefixLength
3GPP name -
Table 170 stubPrefixLength (stub netmask )
178 DN70257257
IP Configuration Plan Interface Parameters
Id:0900d805808e2b75Confidential
ISPF Parameters
21.20 routeCost (Route Cost)
Managed Object -
Parameter group -
Classification -
Multiplicity 1
Description The parameter defines mask length of the stub network address range. The corre-sponding MML command group: ZQKH, "stub network mask length".
Range 1... 32
Step 1
Units -
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • RNC <-> RAC • RAC <-> RACApp
References -
Table 170 stubPrefixLength (stub netmask ) (Cont.)
Parameter name Route Cost
Abbreviated name routeCost
3GPP name -
Managed Object ISPF
Parameter group -
Classification -
Multiplicity 1
Description The cost of injecting a default route into the stub. This parameter applies only to a stub area. This parameter can also be called the stub default cost. The correspond-ing MML command group: ZQKE, "stub area route cost". It exists only when it is a stub Area.
Table 171 routeCost (Route Cost)
DN70257257 179
IP Configuration Plan Interface Parameters ISPF Parameters
Id:0900d805808e2b75Confidential
21.21 stubArea (Stub Area)
Range 1... 65535
Step 1
Units -
Formula for getting internal value
internal_value = gui_value
Default value 1
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • RAC <-> RNC • RACApp <-> RAC
References -
Table 171 routeCost (Route Cost) (Cont.)
Parameter name Stub Area
Abbreviated name stubArea
3GPP name -
Managed Object ISPF
Parameter group -
Classification -
Multiplicity 1
Description The stub area parameter block is required only if the area identification specifies a non-backbone area.
The stub area parameter specifies an area in which there are no Autonomous System External (ASE) routes. ASE routes are routes to destinations external to the AS. If this parameter is set to yes, the area must be a stub, so the external routing capability is disabled. The default value is N.
Y = Stub area.
N = Not a stub area.
The corresponding MML command group: ZQKE, "stub area".
Range N (0), Y (1)
Table 172 stubArea (Stub Area)
180 DN70257257
IP Configuration Plan Interface Parameters
Id:0900d805808e2b75Confidential
ISPF Parameters
21.22 stubbyArea (Stubby Area)
Step -
Units -
Formula for getting internal value
gui ==> internal
N ==> 0
Y ==> 1
Default value N (0)
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • RAC <-> RNC • RACApp <-> RAC
References -
Table 172 stubArea (Stub Area) (Cont.)
Parameter name Stubby Area
Abbreviated name stubbyArea
3GPP name -
Managed Object ISPF
Parameter group -
Classification -
Multiplicity 1
Description An area in which there are no ASE routes and summary routes. This parameter applies only to a stub area. The default value is N.
Y= Totally stubby area.
N = Not a totally stubby area.
The corresponding MML command group: ZQKE, "totally stubby area".
Range N (0), Y (1)
Step -
Units -
Table 173 stubbyArea (Stubby Area)
DN70257257 181
IP Configuration Plan Interface Parameters ISPF Parameters
Id:0900d805808e2b75Confidential
21.23 virLinkEntries (Virtual Link Entries)
Formula for getting internal value
gui ==> internal
N ==> 0
Y ==> 1
Default value N (0)
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • RAC <-> RNC • RACApp <-> RAC
References -
Table 173 stubbyArea (Stubby Area) (Cont.)
Parameter name Virtual Link Entries
Abbreviated name virLinkEntries
3GPP name -
Managed Object ISPF
Parameter group -
Classification -
Multiplicity 8
Description OSPF virtual link list
Formula for getting internal value
-
Default value -
Default value notes -
Related functions -
Child parameters • deadInterval • helloInterval • password • remoteRouteId • type
Modification On-Line
Table 174 virLinkEntries (Virtual Link Entries)
182 DN70257257
IP Configuration Plan Interface Parameters
Id:0900d805808e2b75Confidential
ISPF Parameters
21.24 deadInterval (Dead Interval)
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • RAC <-> RNC • RACApp <-> RAC
References -
Table 174 virLinkEntries (Virtual Link Entries) (Cont.)
Parameter name Dead Interval
Abbreviated name deadInterval
3GPP name -
Managed Object -
Parameter group -
Classification -
Multiplicity 1
Description The length of being unable to hear a router's hello packets before the router declares that the neighbour is down. The length is given in seconds. This field must be the same on the other end of the virtual link. The value of the router dead interval has to be bigger than the hello interval. The corresponding MML command group: ZQKV, "router dead interval".
Range 1... 65535
Step 1
Units -
Formula for getting internal value
internal_value = gui_value
Default value 120
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Table 175 deadInterval (Dead Interval)
DN70257257 183
IP Configuration Plan Interface Parameters ISPF Parameters
Id:0900d805808e2b75Confidential
21.25 helloInterval (Hello Interval)
Interfaces • RAC <-> RNC • RACApp <-> RAC
References -
Table 175 deadInterval (Dead Interval) (Cont.)
Parameter name Hello Interval
Abbreviated name helloInterval
3GPP name -
Managed Object -
Parameter group -
Classification -
Multiplicity 1
Description The length between hello packets sent by the router on the interface. The length is given in seconds. This field must be the same on the other end of the virtual link. The corresponding MML command group: ZQKV, "hello interval".
Range 1... 65535
Step 1
Units -
Formula for getting internal value
internal_value = gui_value
Default value 30
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • RAC <-> RNC • RACApp <-> RAC
References -
Table 176 helloInterval (Hello Interval)
184 DN70257257
IP Configuration Plan Interface Parameters
Id:0900d805808e2b75Confidential
ISPF Parameters
21.26 password (Password)
21.27 remoteRouteId (Remote Route Id)
Parameter name Password
Abbreviated name password
3GPP name -
Managed Object -
Parameter group -
Classification -
Multiplicity 1
Description If you set the authentication type to SIMPLE, a password is required. If it is SIMPLE, the password is an ASCII string of 1 to 8 characters.
The corresponding MML command: ZQKV, "password".
Range 1...8
Step -
Units characters
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • RAC <-> RNC • RACApp <-> RAC
References -
Table 177 password (Password)
Parameter name Remote Route Id
Abbreviated name remoteRouteId
3GPP name -
Managed Object -
Table 178 remoteRouteId (Remote Route Id)
DN70257257 185
IP Configuration Plan Interface Parameters ISPF Parameters
Id:0900d805808e2b75Confidential
21.28 type (type)
Parameter group -
Classification -
Multiplicity 1
Description The router ID of the remote endpoint of the virtual link. The corresponding MML command group: ZQKV, "router identification".
Range 7...15
Step -
Units characters
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • RAC <-> RNC • RACApp <-> RAC
References -
Table 178 remoteRouteId (Remote Route Id) (Cont.)
Parameter name type
Abbreviated name type
3GPP name -
Managed Object -
Parameter group -
Classification -
Multiplicity 1
Table 179 type (type)
186 DN70257257
IP Configuration Plan Interface Parameters
Id:0900d805808e2b75Confidential
ISPF Parameters
Description An interface that is put into passive mode will not send hello packets out of The type of authentication scheme to use for the virtual link. In general, routers on a given link must agree on the authentication configuration in order to form neighbour adja-cencies. This is used to guarantee that routing information is accepted only from trusted routers. NONE = No authentitacion used. SIMPLE = Simple password authentication. The corresponding MML command group: ZQKV, "authentication".
Range NONE (0), SIMPLE (1)
Step -
Units -
Formula for getting internal value
gui ==> internal
NONE ==> 0
SIMPLE ==> 1
Default value NONE (0)
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • RAC <-> RNC • RACApp <-> RAC
References -
Table 179 type (type) (Cont.)
DN70257257 187
IP Configuration Plan Interface Parameters ISPRT Parameters
Id:0900d805808e2b75Confidential
22 ISPRT Parameters
22.1 interfaceEntries (Interface Entries)
22.2 ifName (Interface Name)
Parameter name Interface Entries
Abbreviated name interfaceEntries
3GPP name -
Managed Object ISPRT
Parameter group -
Classification -
Multiplicity 64
Description Defines the interface list which is redistributed into the OSPF.
Formula for getting internal value
-
Default value -
Default value notes -
Related functions -
Child parameters • ifName • metric
Modification On-Line
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • RNC <-> RAC • RAC <-> RACApp
References -
Table 180 interfaceEntries (Interface Entries)
Parameter name Interface Name
Abbreviated name ifName
3GPP name -
Managed Object -
Parameter group -
Table 181 ifName (Interface Name)
188 DN70257257
IP Configuration Plan Interface Parameters
Id:0900d805808e2b75Confidential
ISPRT Parameters
22.3 metric (Metric)
Classification -
Multiplicity 1
Description This parameter defines the interface name which is redistributed into the OSPF. The corresponding MML command: ZQKU.
If ALL is given, all valid interface routes are redistributed.
Range 3...8
Step -
Units characters
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • RNC <-> RAC • RAC <-> RACApp
References -
Table 181 ifName (Interface Name) (Cont.)
Parameter name Metric
Abbreviated name metric
3GPP name -
Managed Object -
Parameter group -
Classification -
Multiplicity 1
Description This parameter defines the cost for the redistribution.
The corresponding MML command group: ZQKU,"metric".
Range 1... 16777215
Step 1
Table 182 metric (Metric)
DN70257257 189
IP Configuration Plan Interface Parameters ISPRT Parameters
Id:0900d805808e2b75Confidential
22.4 isprtId (ISPRT identifier)
Units -
Formula for getting internal value
internal_value = gui_value
Default value 1
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • RNC <-> RAC • RAC <-> RACApp
References -
Table 182 metric (Metric) (Cont.)
Parameter name ISPRT identifier
Abbreviated name isprtId
3GPP name -
Managed Object ISPRT
Parameter group -
Classification -
Multiplicity 1
Description Identifies the OSPF redistribution configuration in the system. There is only one instance in one IPNO. The identifier is part of the distinguished name and is formed in the following way: NE-x/IPNO-unitType-unitIndex/ISPRT-x. For example: RNC-1/IPNO-OMU-0/ISPRT-1. The corresponding MML command group: ZQKU.
Range 1... 1
Step 1
Units -
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes default value is not possible
Related functions -
Table 183 isprtId (ISPRT identifier)
190 DN70257257
IP Configuration Plan Interface Parameters
Id:0900d805808e2b75Confidential
ISPRT Parameters
22.5 redistAllEntries (Redistribute Entries)
Modification Not modifiable
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • RNC <-> RAC • RAC <-> RACApp
References -
Table 183 isprtId (ISPRT identifier) (Cont.)
Parameter name Redistribute Entries
Abbreviated name redistAllEntries
3GPP name -
Managed Object ISPRT
Parameter group -
Classification -
Multiplicity 2
Description Defines the redistribute all list.
Formula for getting internal value
-
Default value -
Default value notes -
Related functions -
Child parameters • metric • type
Modification On-Line
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • RNC <-> RAC • RAC <-> RACApp
References -
Table 184 redistAllEntries (Redistribute Entries)
DN70257257 191
IP Configuration Plan Interface Parameters ISPRT Parameters
Id:0900d805808e2b75Confidential
22.6 metric (Metric)
22.7 type (Type)
Parameter name Metric
Abbreviated name metric
3GPP name -
Managed Object -
Parameter group -
Classification -
Multiplicity 1
Description This parameter defines the cost for the redistribution.
The corresponding MML command group: ZQKU,"metric".
Range 1... 16777215
Step 1
Units -
Formula for getting internal value
internal_value = gui_value
Default value 1
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • RNC <-> RAC • RAC <-> RACApp
References -
Table 185 metric (Metric)
Parameter name Type
Abbreviated name type
3GPP name -
Managed Object -
Parameter group -
Table 186 type (Type)
192 DN70257257
IP Configuration Plan Interface Parameters
Id:0900d805808e2b75Confidential
ISPRT Parameters
22.8 routeEntries (Route Entries)
Classification -
Multiplicity 1
Description This parameter defines the type which redistributes all valid static route or all valid interface routes into OSPF.
The corresponding MML command group: ZQKU.
Range Static route (0), Interface (1)
Step -
Units -
Formula for getting internal value
gui ==> internal
Static route ==> 0
Interface ==> 1
Default value -
Default value notes Default value is not possible
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • RNC <-> RAC • RAC <-> RACApp
References -
Table 186 type (Type) (Cont.)
Parameter name Route Entries
Abbreviated name routeEntries
3GPP name -
Managed Object ISPRT
Parameter group -
Classification -
Multiplicity 64
Description Defines the redistribute static route list which is redistributed into the OSPF.
Formula for getting internal value
-
Table 187 routeEntries (Route Entries)
DN70257257 193
IP Configuration Plan Interface Parameters ISPRT Parameters
Id:0900d805808e2b75Confidential
22.9 destIPAddrIPV4 (DestIPAddrIPV4)
Default value -
Default value notes -
Related functions -
Child parameters • destIPAddrIPV4 • gatewayIPV4 • metric • netmask
Modification On-Line
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • RNC <-> RAC • RAC <-> RACApp
References -
Table 187 routeEntries (Route Entries) (Cont.)
Parameter name DestIPAddrIPV4
Abbreviated name destIPAddrIPV4
3GPP name -
Managed Object -
Parameter group -
Classification -
Multiplicity 1
Description The parameter defines the destination IP address of the static route which is redis-tributed and the address is specified in the conventional dot notation (#.#.#.#).
The corresponding MML command group: ZQKU. If ALL is given, all valid static routes are redistributed.
Range 7...15
Step -
Units characters
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes -
Table 188 destIPAddrIPV4 (DestIPAddrIPV4)
194 DN70257257
IP Configuration Plan Interface Parameters
Id:0900d805808e2b75Confidential
ISPRT Parameters
22.10 gatewayIPV4 (GatewayIPV4)
Related functions -
Modification Not modifiable
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • RNC <-> RAC • RAC <-> RACApp
References -
Table 188 destIPAddrIPV4 (DestIPAddrIPV4) (Cont.)
Parameter name GatewayIPV4
Abbreviated name gatewayIPV4
3GPP name -
Managed Object -
Parameter group -
Classification -
Multiplicity 1
Description The parameter defines the gateway IP address of the static route which is redistrib-uted and the address is specified in the conventional dot notation (#.#.#.#).
Range 7...15
Step -
Units characters
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes -
Related functions -
Modification Not modifiable
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Table 189 gatewayIPV4 (GatewayIPV4)
DN70257257 195
IP Configuration Plan Interface Parameters ISPRT Parameters
Id:0900d805808e2b75Confidential
22.11 metric (Metric)
Interfaces • RNC <-> RAC • RAC <-> RACApp
References -
Table 189 gatewayIPV4 (GatewayIPV4) (Cont.)
Parameter name Metric
Abbreviated name metric
3GPP name -
Managed Object -
Parameter group -
Classification -
Multiplicity 1
Description This parameter defines the cost for the redistribution.
The corresponding MML command group: ZQKU,"metric".
Range 1... 16777215
Step 1
Units -
Formula for getting internal value
internal_value = gui_value
Default value 1
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • RNC <-> RAC • RAC <-> RACApp
References -
Table 190 metric (Metric)
196 DN70257257
IP Configuration Plan Interface Parameters
Id:0900d805808e2b75Confidential
ISPRT Parameters
22.12 netmask (Netmask)
Parameter name Netmask
Abbreviated name netmask
3GPP name -
Managed Object -
Parameter group -
Classification -
Multiplicity 1
Description This parameter defines the netmask of the static route which is redistributed.
The corresponding MML command group: ZQKU.
Range 1... 32
Step 1
Units -
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes Default value is not possible
Related functions -
Modification Not modifiable
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • RNC <-> RAC • RAC <-> RACApp
References -
Table 191 netmask (Netmask)
DN70257257 197
IP Configuration Plan Interface Parameters ITRKGRP Parameters
Id:0900d805808e2b75Confidential
23 ITRKGRP Parameters
23.1 trkGrpBoolVal (Network Status Tracker Group Operation Bool Value)
Parameter name Network Status Tracker Group Operation Bool Value
Abbreviated name trkGrpBoolVal
3GPP name -
Managed Object ITRKGRP
Parameter group -
Classification -
Multiplicity 1
Description This parameter defines the bool value of the network tracker group.
The input value is only valid when creating the non-default tracker group(trk-GrpId!=0) with trkGrpOperation=BOOL. It is ignored when the trkGrpOperation is WEIGHT.
When creating the default tracker group(trkGrpId=0), this parameter is the fixed value 0(OR).
The corresponding commands: ZQJC.
Range OR (0), AND (1)
Step -
Units -
Formula for getting internal value
gui ==> internal
OR ==> 0
AND ==> 1
Default value OR (0)
Default value notes -
Related functions -
Modification Not modifiable
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • RNC <-> RAC • RAC <-> RACApp
References -
Table 192 trkGrpBoolVal (Network Status Tracker Group Operation Bool Value)
198 DN70257257
IP Configuration Plan Interface Parameters
Id:0900d805808e2b75Confidential
ITRKGRP Parameters
23.2 trkGrpId (Network Status Tracker Group ID)
Parameter name Network Status Tracker Group ID
Abbreviated name trkGrpId
3GPP name -
Managed Object ITRKGRP
Parameter group -
Classification -
Multiplicity 1
Description This parameter defines the network tracker group identification.
Group ID 0 (default) is unique on the single EIPU unit. However, other group IDs (1~127) are unique on the whole RNC.
When creating the tracker group with trkGrpId=0, the following parameters are the fixed values. All the input values are ignored.
trkGrpType: 0(Faulty Switchover)
trkGrpOperation: 0(BOOL)
trkGrpBoolVal: 0(OR)
When creating the group with trkGrpId 0, two ITRKOBJs will be created without the trkObjWeight values:
ITRKOBJ-IFGE0
ITRKOBJ-IFGE1
When deleting an ITRKGRP, all the ITRKOBJs attached will be deleted.
The identifier is part of the distinguished name and it is formed in the following way: NE-x/IPNO-unitType-unitIndex/ITRKGRP-trkGrpId. For example: RNC-02/IPNO-NPGEP-0/ITRKGRP-123.
The corresponding commands: ZQJC, ZQJM
Range 0... 127
Step 1
Units -
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes -
Related functions -
Modification Not modifiable
Related parameters -
Parameter relationships -
Related options -
Table 193 trkGrpId (Network Status Tracker Group ID)
DN70257257 199
IP Configuration Plan Interface Parameters ITRKGRP Parameters
Id:0900d805808e2b75Confidential
23.3 trkGrpOperation (Network Status Tracker Group Opera-tion)
Feature dependencies -
Interfaces • RNC <-> RAC • RAC <-> RACApp
References -
Table 193 trkGrpId (Network Status Tracker Group ID) (Cont.)
Parameter name Network Status Tracker Group Operation
Abbreviated name trkGrpOperation
3GPP name -
Managed Object ITRKGRP
Parameter group -
Classification -
Multiplicity 1
Description This parameter defines the tracker operation of the network tracker group.
The input value is only valid when creating the non-default tracker group(trk-GrpId!=0).
When creating the default tracker group(trkGrpId=0), this parameter is the fixed value 0(BOOL).
The corresponding commands: ZQJC.
Range BOOL (0), WEIGHT (1)
Step -
Units -
Formula for getting internal value
gui ==> internal
BOOL ==> 0
WEIGHT ==> 1
Default value BOOL (0)
Default value notes -
Related functions -
Modification Not modifiable
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Table 194 trkGrpOperation (Network Status Tracker Group Operation)
200 DN70257257
IP Configuration Plan Interface Parameters
Id:0900d805808e2b75Confidential
ITRKGRP Parameters
23.4 trkGrpWeightVal (Network Status Tracker Group Opera-tion Weight Value)
Interfaces • RNC <-> RAC • RAC <-> RACApp
References -
Table 194 trkGrpOperation (Network Status Tracker Group Operation) (Cont.)
Parameter name Network Status Tracker Group Operation Weight Value
Abbreviated name trkGrpWeightVal
3GPP name -
Managed Object ITRKGRP
Parameter group -
Classification -
Multiplicity 1
Description This parameter defines the weight value of the network tracker group.
The input value is only valid when creating the non-default tracker group(trk-GrpId!=0) with trkGrpOperation=WEIGHT. It is ignored when the trkGrpOperation is BOOL.
When creating the default tracker group(trkGrpId=0), this parameter is ignored.
The corresponding commands: ZQJC.
Range 1... 999
Step 1
Units -
Formula for getting internal value
internal_value = gui_value
Default value 100
Default value notes -
Related functions -
Modification Not modifiable
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • RNC <-> RAC • RAC <-> RACApp
References -
Table 195 trkGrpWeightVal (Network Status Tracker Group Operation Weight Value)
DN70257257 201
IP Configuration Plan Interface Parameters ITRKGRP Parameters
Id:0900d805808e2b75Confidential
23.5 trkType (Network Status Tracker Group Type)
Parameter name Network Status Tracker Group Type
Abbreviated name trkType
3GPP name -
Managed Object ITRKGRP
Parameter group -
Classification -
Multiplicity 1
Description This parameter defines the tracker type of the network tracker group.
The input value is only valid when creating the non-default tracker group(trk-GrpId!=0).
When creating the default tracker group(trkGrpId=0), this parameter is the fixed value 0(Faulty Switchover).
The corresponding commands: ZQJC.
Range Faulty Switchover (0)
Step -
Units -
Formula for getting internal value
gui ==> internal
Faulty Switchover ==> 0
Default value Faulty Switchover (0)
Default value notes -
Related functions -
Modification Not modifiable
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • RNC <-> RAC • RAC <-> RACApp
References -
Table 196 trkType (Network Status Tracker Group Type)
202 DN70257257
IP Configuration Plan Interface Parameters
Id:0900d805808e2b75Confidential
ITRKOBJ Parameters
24 ITRKOBJ Parameters
24.1 trkObjName (Network Status Tracker Object Name)
Parameter name Network Status Tracker Object Name
Abbreviated name trkObjName
3GPP name -
Managed Object ITRKOBJ
Parameter group -
Classification -
Multiplicity 1
Description This parameter defines the name of the network status tracker object.
The name must be one of the following names: "IFGE0", "IFGE1", "IFFE0", "IFFE1".
The ITRKOBJ cannot be added/deleted to/from the default ITRKGRP (trkGrpId=0). The ITRKOBJs in the default ITRKGRP are added/deleted automatically when cre-ating/deleting the default ITRKGRP.
The identifier is part of the distinguished name and it is formed in the following way: NE-x/IPNO-unitType-unitIndex/ITRKGRP-trkGrpId/ITRKOBJ-xxx. For example: RNC-02/IPNO-NPGEP-0/ITRKGRP-123/ITRKOBJ-IFGE0.
The corresponding commands: ZQJM.
Range 3...8
Step -
Units characters
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes -
Related functions -
Modification Not modifiable
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • RNC <-> RAC • RAC <-> RACApp
References -
Table 197 trkObjName (Network Status Tracker Object Name)
DN70257257 203
IP Configuration Plan Interface Parameters ITRKOBJ Parameters
Id:0900d805808e2b75Confidential
24.2 trkObjWeight (Network Status Tracker Object Weight)
Parameter name Network Status Tracker Object Weight
Abbreviated name trkObjWeight
3GPP name -
Managed Object ITRKOBJ
Parameter group -
Classification -
Multiplicity 1
Description This parameter defines the weight of the network status tracker object.
The input value is only valid when creating the ITRKOBJ in the non-default tracker group(trkGrpId!=0) with trkGrpOperation=WEIGHT. It is ignored when creating the ITRKOBJ in the tracker group with trkGrpOperation=BOOL.
The corresponding commands: ZQJM
Range 1... 999
Step 1
Units -
Formula for getting internal value
internal_value = gui_value
Default value 100
Default value notes -
Related functions -
Modification Not modifiable
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • RNC <-> RAC • RAC <-> RACApp
References -
Table 198 trkObjWeight (Network Status Tracker Object Weight)
204 DN70257257
IP Configuration Plan Interface Parameters
Id:0900d805808e2b75Confidential
IUBSNT Parameters
25 IUBSNT Parameters
25.1 IPV4MaskLength (IPV4 mask length)
25.2 IPV4SubnetAddress (IPV4 subnet address)
Parameter name IPV4 mask length
Abbreviated name IPV4MaskLength
3GPP name -
Managed Object IUBSNT
Parameter group -
Classification -
Multiplicity 1
Description This parameter defines the local subnet mask length.
The corresponding MML command: ZQMN,"local subnet mask length".
Range 4... 26
Step 1
Units -
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes -
Related functions -
Modification Not modifiable
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • RNC <-> RAC • RAC <-> RACApp
References -
Table 199 IPV4MaskLength (IPV4 mask length)
Parameter name IPV4 subnet address
Abbreviated name IPV4SubnetAddress
3GPP name -
Table 200 IPV4SubnetAddress (IPV4 subnet address)
DN70257257 205
IP Configuration Plan Interface Parameters IUBSNT Parameters
Id:0900d805808e2b75Confidential
25.3 assocMaxRetrans (Association max retrans)
Managed Object IUBSNT
Parameter group -
Classification -
Multiplicity 1
Description This parameter defines the local subnet IPv4 address.
The address is specified in the conventional dot notation (#.#.#.#). The correspond-ing MML command: ZQMN,"local subnet ipv4 address".
Range 7...15
Step -
Units characters
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes -
Related functions -
Modification Not modifiable
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • RNC <-> RAC • RAC <-> RACApp
References -
Table 200 IPV4SubnetAddress (IPV4 subnet address) (Cont.)
Parameter name Association max retrans
Abbreviated name assocMaxRetrans
3GPP name -
Managed Object IUBSNT
Parameter group -
Classification -
Multiplicity 1
Table 201 assocMaxRetrans (Association max retrans)
206 DN70257257
IP Configuration Plan Interface Parameters
Id:0900d805808e2b75Confidential
IUBSNT Parameters
25.4 hbInterval (HB interval)
Description This parameter defines the association Max.Retrans (Maximum number of unac-knowledged transmissions (including heartbeats) per association).
The corresponding MML command: ZQMP.
Range 1... 15
Step 1
Units -
Formula for getting internal value
internal_value = gui_value
Default value 5
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • RAC <-> RNC • RACApp <-> RAC
References -
Table 201 assocMaxRetrans (Association max retrans) (Cont.)
Parameter name HB interval
Abbreviated name hbInterval
3GPP name -
Managed Object IUBSNT
Parameter group -
Classification -
Multiplicity 1
Description This parameter defines HB.interval in milliseconds.
The corresponding MML command: ZQMP.
Range 100... 300000
Step 1
Units milliseconds
Table 202 hbInterval (HB interval)
DN70257257 207
IP Configuration Plan Interface Parameters IUBSNT Parameters
Id:0900d805808e2b75Confidential
25.5 iubsntId (Iubsnt Identifier)
Formula for getting internal value
internal_value = gui_value
Default value 1000
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • RAC <-> RNC • RACApp <-> RAC
References -
Table 202 hbInterval (HB interval) (Cont.)
Parameter name Iubsnt Identifier
Abbreviated name iubsntId
3GPP name -
Managed Object IUBSNT
Parameter group -
Classification -
Multiplicity 1
Description Identifies the local subnet configuration in the system. The identifier is part of the distinguished name and is formed in the following way: NE-x/IUBSNT-x. For example: RNC-1/IUBSNT-1. The corresponding MML command: ZQMN.
Range 1... 1
Step 1
Units -
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes -
Related functions -
Modification Not modifiable
Table 203 iubsntId (Iubsnt Identifier)
208 DN70257257
IP Configuration Plan Interface Parameters
Id:0900d805808e2b75Confidential
IUBSNT Parameters
25.6 maxInitRetrans (MaxInitRetrans)
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • RAC <-> RNC • RACApp <-> RAC
References -
Table 203 iubsntId (Iubsnt Identifier) (Cont.)
Parameter name MaxInitRetrans
Abbreviated name maxInitRetrans
3GPP name -
Managed Object IUBSNT
Parameter group -
Classification -
Multiplicity 1
Description This parameter defines Max.Init.Retransmits.
Range 1... 254
Step 1
Units -
Formula for getting internal value
internal_value = gui_value
Default value 8
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • RAC <-> RNC • RACApp <-> RAC
References -
Table 204 maxInitRetrans (MaxInitRetrans)
DN70257257 209
IP Configuration Plan Interface Parameters IUBSNT Parameters
Id:0900d805808e2b75Confidential
25.7 pathMaxRetrans (PathMaxRetrans)
25.8 rtoInitial (RTO Initial)
Parameter name PathMaxRetrans
Abbreviated name pathMaxRetrans
3GPP name -
Managed Object IUBSNT
Parameter group -
Classification -
Multiplicity 1
Description This parameter defines Path.Max.Retrans (Maximum number of unacknowledged transmissions (including heartbeats) per path).
The corresponding MML command: ZQMP.
Range 1... 15
Step 1
Units -
Formula for getting internal value
internal_value = gui_value
Default value 5
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • RAC <-> RNC • RACApp <-> RAC
References -
Table 205 pathMaxRetrans (PathMaxRetrans)
Parameter name RTO Initial
Abbreviated name rtoInitial
3GPP name -
Managed Object IUBSNT
Table 206 rtoInitial (RTO Initial)
210 DN70257257
IP Configuration Plan Interface Parameters
Id:0900d805808e2b75Confidential
IUBSNT Parameters
25.9 rtoMax (RTO Max)
Parameter group -
Classification -
Multiplicity 1
Description This parameter defines RTO.initial (Initial retransmission time-out in milliseconds).
The corresponding MML command group: ZQMP.
Range 10... 60000
Step 1
Units milliseconds
Formula for getting internal value
internal_value = gui_value
Default value 1000
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • RAC <-> RNC • RACApp <-> RAC
References -
Table 206 rtoInitial (RTO Initial) (Cont.)
Parameter name RTO Max
Abbreviated name rtoMax
3GPP name -
Managed Object IUBSNT
Parameter group -
Classification -
Multiplicity 1
Description This parameter defines RTO.Max (Maximum value of retransmission time-out in milliseconds).
The corresponding MML command: ZQMP.
Table 207 rtoMax (RTO Max)
DN70257257 211
IP Configuration Plan Interface Parameters IUBSNT Parameters
Id:0900d805808e2b75Confidential
25.10 rtoMin (RTO Min)
Range 10... 120000
Step 1
Units milliseconds
Formula for getting internal value
internal_value = gui_value
Default value 2000
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • RAC <-> RNC • RACApp <-> RAC
References -
Table 207 rtoMax (RTO Max) (Cont.)
Parameter name RTO Min
Abbreviated name rtoMin
3GPP name -
Managed Object IUBSNT
Parameter group -
Classification -
Multiplicity 1
Description This parameter defines RTO.Min (Minimum value of retransmission time-out in mil-liseconds).
The corresponding MML command group: ZQMP.
Range 10... 20000
Step 1
Units milliseconds
Formula for getting internal value
internal_value = gui_value
Default value 750
Table 208 rtoMin (RTO Min)
212 DN70257257
IP Configuration Plan Interface Parameters
Id:0900d805808e2b75Confidential
IUBSNT Parameters
25.11 sackPeriod (sackPeriod)
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • RAC <-> RNC • RACApp <-> RAC
References -
Table 208 rtoMin (RTO Min) (Cont.)
Parameter name sackPeriod
Abbreviated name sackPeriod
3GPP name -
Managed Object IUBSNT
Parameter group -
Classification -
Multiplicity 1
Description This parameter defines the sack period in milliseconds.
The corresponding MML command group: ZQMN, "sack period".
Range 0... 500
Step 1
Units milliseconds
Formula for getting internal value
internal_value = gui_value
Default value 200
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Table 209 sackPeriod (sackPeriod)
DN70257257 213
IP Configuration Plan Interface Parameters IUBSNT Parameters
Id:0900d805808e2b75Confidential
25.12 validCookieLife (Valid Cookie Life)
Interfaces • RNC <-> RAC • RAC <-> RACApp
References -
Table 209 sackPeriod (sackPeriod) (Cont.)
Parameter name Valid Cookie Life
Abbreviated name validCookieLife
3GPP name -
Managed Object IUBSNT
Parameter group -
Classification -
Multiplicity 1
Description This parameter defines Valid.Cookie.Life.
Range 5000... 120000
Step 1
Units milliseconds
Formula for getting internal value
internal_value = gui_value
Default value 60000
Default value notes -
Related functions -
Modification On-Line
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • RAC <-> RNC • RACApp <-> RAC
References -
Table 210 validCookieLife (Valid Cookie Life)
214 DN70257257
IP Configuration Plan Interface Parameters
Id:0900d805808e2b75Confidential
IVIF Parameters
26 IVIF Parameters
26.1 parentInterface (Vlan physical Interface)
26.2 vid (Vlan id)
Parameter name Vlan physical Interface
Abbreviated name parentInterface
3GPP name -
Managed Object IVIF
Parameter group -
Classification -
Multiplicity 1
Description This parameter defines the physical interface to which the VLAN interface is attached to.
The corresponding MML command group: ZQRM, "vlan physical interface".
Range 3...8
Step -
Units characters
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes -
Related functions -
Modification Not modifiable
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • RNC <-> RAC • RAC <-> RACApp
References -
Table 211 parentInterface (Vlan physical Interface)
Parameter name Vlan id
Abbreviated name vid
Table 212 vid (Vlan id)
DN70257257 215
IP Configuration Plan Interface Parameters IVIF Parameters
Id:0900d805808e2b75Confidential
26.3 vlanIfId (Vlan Interface Identifier)
3GPP name -
Managed Object IVIF
Parameter group -
Classification -
Multiplicity 1
Description This parameter defines the VLAN id of the VLAN interface.
The corresponding MML command group: ZQRM, "vlan identifier".
Range 2... 4094
Step 1
Units -
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes Default value is not possible
Related functions -
Modification Not modifiable
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • RNC <-> RAC • RAC <-> RACApp
References -
Table 212 vid (Vlan id) (Cont.)
Parameter name Vlan Interface Identifier
Abbreviated name vlanIfId
3GPP name -
Managed Object IVIF
Parameter group -
Classification -
Multiplicity 1
Table 213 vlanIfId (Vlan Interface Identifier)
216 DN70257257
IP Configuration Plan Interface Parameters
Id:0900d805808e2b75Confidential
IVIF Parameters
Description This parameter identifies the VLAN interface within the IP node entity in the system. The identifier is part of the distinguished name and it is formed in the following way: NE-x/IPNO-unitType-unitIndex/IVIF-ifName. For example: RNC-1/IPNO-NPGEP-0/IVIF-VL1.
The VLAN interface name is VLx, where x is a number and the range is from 0 to 9999.
The corresponding MML command group: ZQRM, "vlan interface".
Range 3...8
Step -
Units characters
Formula for getting internal value
internal_value = gui_value
Default value -
Default value notes -
Related functions -
Modification Not modifiable
Related parameters -
Parameter relationships -
Related options -
Feature dependencies -
Interfaces • RNC <-> RAC • RAC <-> RACApp
References -
Table 213 vlanIfId (Vlan Interface Identifier) (Cont.)