1
IPD Series PTZ & Positioning Camera User Installation Manual
Model Series: PTZ Dome Range CAM-IPD-xx-xxx-DN Series. CAM-IPD-xx-xxx-IC. CAM-IPD-xx-xxx-IRL, CAM-IPD-xx-xxx-IR, Positioning PTZ CAM-IRZ-xx-xxx-IR. CAM-LTZ-xx-xxx-IRL
2
Contents
1. Precautions ............................................................................................................................................................... 3
2. Installation ................................................................................................................................................................ 4 2.1 Cautions ............................................................................................................................................................ 4
2.2 Distributing of power close to the device. ........................................................................................................ 4
2.3 Lightning Proof and Surge Protection ............................................................................................................... 5
2.4 Water Proof ....................................................................................................................................................... 5
2.5 Preparation of Installation ................................................................................................................................ 5
2.6 Model Range ..................................................................................................................................................... 2
2.7 Bracket Selection .............................................................................................................................................. 2
2.8 Installation ........................................................................................................................................................ 3
2.8.1 Wall Mount ................................................................................................................................................... 3
2.8.2 Pendant Mount ............................................................................................................................................. 4
2.8.3 Cable Connection .......................................................................................................................................... 4
2.8.4 Positioning Unit ............................................................................................................................................. 2
3. Performance.............................................................................................................................................................. 2 3.1 Generic Production Specifications .................................................................................................................... 2
3.2 Camera Technical Specifications ....................................................................................................................... 2
3.3 Network IP Specifications ................................................................................................................................. 3
4. Performance and Application ................................................................................................................................... 4 4.1 PTZ Performance and Features ......................................................................................................................... 4
4.2 Camera ID .......................................................................................................................................................... 2
4.3 Auto-run motion ............................................................................................................................................... 2
4.4 Camera Control ................................................................................................................................................. 2
5. Network Configuration ............................................................................................................................................. 2
5.1 Login .................................................................................................................................................................. 2
5.2 Download ActiveX plugin .................................................................................................................................. 2
5.3 Login Browser.................................................................................................................................................... 3
5.4 Live Preview ...................................................................................................................................................... 3
5.5 Client Search Tool ............................................................................................................................................. 4
6. Appendix ................................................................................................................................................................... 5
6.1 Basic Operation ................................................................................................................................................. 5
6.2 Shortcut Keys .................................................................................................................................................... 6
6.3 Menu Index ....................................................................................................................................................... 7
6.4 CAD Dimensions ................................................................................................................................................ 8
6.4.1 Internal PTZ and D/N PTZ Models. ............................................................................................................ 8
6.4.2 Laser LED and IR LED PTZ Models. ............................................................................................................ 8
6.4.3 Positioning units ........................................................................................................................................ 8
6.5 RS485 Bus Basic Knowledge .............................................................................................................................. 9
7. Maintenance and Service ........................................................................................................................................ 10 7.1 Limited Warranty ............................................................................................................................................ 10
7.2 Warranty terms ............................................................................................................................................... 10
7.3 Warranty Shipping .......................................................................................................................................... 10
8. Regulatory Information ........................................................................................................................................... 11 8.1 EU Conformity Statement ............................................................................................................................... 11
3
1. Precautions
Electrical safety Conform to the country and local electrical safety standard when using or installing the product. Transportation Protect the PTZ against extremes of pressure, vibration, and humidity during shipping, storage, and installation. Use the packaging designed for and supplied with the PTZ camera. Installation of care Please refer to this user installation manual before installation. Please pick up the Infrared parts gently and do not press, you may damage the unit which will cause a malfunction. Requirements to service personnel Qualified technicians should do all the service work. Only when authorized by Aventura Support. Do not disassemble the pan/tilt module Do not remove screws, and don't maintain the parts in the Pan/Tilt by yourself. Only qualified and authorized personnel can undertake repairs. Please contact support for problems and resolutions. Environmental requirements for PTZ: Environmental temp: -25°C ~ +50°C Humidity: <90% Air pressure: 86~106Kpa Power supply: AC 24V/2500MA, 50/60HZ Don't aim the camera to view any strong light directly Don't point the PTZ to the sun or other bright objects. It may affect image quality. The function of waterproof (Outdoor models) The product is water-proof, humidity-proof and dust-proof, which pass the standard of IP66. A high humidity environment may cause damage to the internal workings and should be avoided.
4
2. Installation
2.1 Cautions Please read all this user manual before installation.
Power: AC24V or High PoE when available, use the power devices supplied with the unit only.
Precise optical and electronic parts inside of the product. Avoiding severe pressure, hard vibration, etc. non-correct operation methods, which may cause damage to the product when in transportation and during installation.
Please do not disassemble parts inside of product at random, which may cause a negative influence on the use of the product. No user serviceable parts inside and will void warranty.
Please comply with standards of Electrify Safety and use the supplied transformer with the product. Enough distance must be ensured between Network or RS-485 cable, Video signal cable and equipment’s of high voltage when doing transmission. Lightning-proof and surge-proof etc. protection measures are needed. The Device subject to abnormal operational use will void warranty.
Do not use product beyond the rated temperature, humidity or specifications of power. Do not place camera pointing to Sun or extreme brightness, care to be taken if installation during the day, when external lighting may not be noticeable. Avoid such locations or adjust external lighting not to interfere with camera positions and operation.
Do not use abrasive cleansers to clean product. Please use a dry cloth to clean up dirt; the Neutral solvent is needed when the surface is not easy to clean.
Handle product with care to avoid or excessive vibration; Incorrect use of camera can result in damage and void the warranty.
Please fix product to the position which is stable and firm. This device is not suitable for mobile applications.
2.2 Distributing of power close to the device. Please refer to right Figure 1 right
It is necessary to keep 50 meters distances at least
between the high voltage unit and the high voltage
cable with the signal transmission line.
Outdoor wiring is best to along under the eve of the
house.
Wiring at void place must adopt by way of sealed steel
tube bury underground, and sealed steel tube should
be grounded.
Under thunderstorm or high inductive voltage region
(e.g., high voltage transformer substation), you must
add extra high-power lightning proof equipment and
install lighting rod.
Outdoor equipment, routes of lighting proof and
ground design must consider according to the request of construction lightning proof and coincide with
connection requests of country and industry standard.
The system must provide an equipotential ground. Grounding equipment must satisfy the anti-jamming and
electrical safety requirements and must not short-circuit or mix connection with high voltage electricity net.
When the system is grounded separately, the ground resistance should be not more than 4 ohms, and a
section of the grounding conducting wire should be less than 25 mm².
1 2 3
1 Power Supply Surge
2 Data Signal Surge
3 Video Signal Surge
45º
Lighting Rod
Install with the 45º of Rod
ProtectiveTube
Earth resistance must
be less than 4
Figure 1
5
2.3 Lightning Proof and Surge Protection This product uses TVS lightning Proof
technology, can prevent the damage of the
equipment caused by kinds of pulse signal such as
instant lightning strike of power below 4000V, the
surge and so on.
At the same time, you must adopt the essential
protective measure according to the actual situation
regarding outdoor installation under guarantee
electricity security. (Refer to the previous chapter)
2.4 Water Proof Outdoor PTZ is waterproof, moisture-proof,
dustproof performance has achieved the IP66
international standard. The indoor PTZ doesn't allow
to install in an outdoor environment which is full of
moisture. - This is not an indoor model! You should
prevent the camera and the internal components
from damage that caused by the long-time water
collecting, such as ice or snow.
2.5 Preparation of Installation The request of the quality of installation person
and maintainer: o All installation and maintenance work
related to this product should complete by technical personnel who qualify for installation and maintenance.
Basic requirements o Please refer to this handbook for detail. o All electrical work must be observed local
latest electricity laws, regulation on fireproof as well as the related rules and regulations:
o Checking everything is completed according to the packing list. Make sure the application place and the way of installation for PTZ are compatible with the request. If not, please contact your supplier.
o Please use this product according to the working conditions request.
o Please handle with the pan/tilt module
carefully, do not extrude various structure parts; The down cover belongs to the senior optics part, do not touch with the hand; Please do not get through power
except for the electrifying inspection in the process of installation.
Check the structure intensity for installation space and installation site.
o Make sure you have enough space to hold this product and its parts of installation in the site.
o Make sure the bearing capacity of ceiling, wall, the bracket that installs the PTZ support the gross weight of the PTZ and the structural parts of the installation. Having the safe coefficient of 4 times or above is necessary.
Installation
Stuff Preparation Please select the type of cables based on transmitting distance:
1. 75Ωimpedance 2. All copper conductor wire 3. 95% copper net structure 4. Network cable RJ45 <100M {330feet} 5. RS485 Communication cables (Refer to
manual appendix) 6. 24VAC Power supply cable (Refer to manual
appendix)
Keep All the Original Package Materials
Please preserve the mode original package material properly after opening the PTZ packing, to return in original package is such conditional require.
Failure to return in the original package may cause further damage to the product, and additional costs and warranty issues can be avoided. Please contact Aventura technical for advice.
Brief introduction of a mounting way The mounting way of pan/tilt: wall mount, pendant mount.
Bracket Installation: Installation position must enable to undertake high weight pressure, which must be 4times of the total weight of PTZ and bracket. The wall must be secure and stable; bracket must attach to a solid wall, and
not a free-standing wall with little or no-load bearing
capacity.
WARNING
2
2.6 Model Range The PTZ consists of several parts, which form the basis of a complete solution. Bracket for fitting, and the main housing body. Positioning model is an all in one complete camera and requires just the installation to a bracket. The Day/Night PTZ dome style models will have a removable dome cover and a module which can be removed. IR and Laser LED models are also fully encapsulated and require only the attachment to the required bracket.
2.7 Bracket Selection
Most cameras are supplied with a standard Wall mount.: Other options available as shown below diagram:
Internal Recess Mount PTZ Day/Night PTZ IR Led PTZ Laser Light PTZ Positioning Unit. PTZ with Thermal or IR LED)
Wall Mount (PTZ & Positioning PTZ) Pendant Mount Corner Mount Pole Mount
3
2.8 Installation
2.8.1 Wall Mount a) The installation site must be able to support
the sum of weight such as the dome, the
bracket, and the pedestal, multiplied by four.
b) The chosen wall of installation site must be
substantial. Make sure the bracket installs on
the wall first and it sturdy and horizontal.
c) Depending on access to the back of the wall, it may be necessary to pull all wires out through the bracket before mounting, then connect wires to cameras and push up into mount before attaching a camera body to the bracket.
d) Attach the bracket to surface with four M6 holes. A suggested depth of 75mm will allow for a perfect fit of supplied bolt anchors.
Note: Be sure to have access for cables at the rear. The rear of the bracket has breakaway slots to allow for side exit of wires against a flat surface.
e) Please pay attention to Figure 2 below ○1
must have an appropriate seal applied to
prevent the water ingress.
f) With the bracket secure you can attach the
dome body using the bolts which fix around
the ○2 holes.
g) You should align the home position, so the
camera is pointing forward.
You need to follow the operation
guide; it’s essential to keep water
away from the internals of the
product. Water damage will not be
covered under warranty repairs.
242mm
200m
m[7
.87"]
170m
m[6
.69"]
60mm[2.36"]
12mm[0.47"]
[9.52"]
140mm[5.51"]
114mm[4.48 "]
Figure 2
WARNING
4
2.8.2 Pendant Mount a) The installation surface must be able to
support the weight of the dome.
b) Do not install on ceiling tiles which are brittle
and would break easily.
c) Attach the bracket to surface with three M6 holes. A suggested depth of 75mm will allow for a perfect fit of supplied bolt anchors.
You need to follow the operation guide; it’s
essential to keep water away from the
internals of the product. Water damage will
not be covered under warranty repairs. The
device is designed for maintenance-free
operation under normal conditions.
d) Before connecting the dome to the pendant
mount bracket, it’s best to present all cables
being connected to the device. And allow for
some movement of wires above the
installation.
e) Connect all cables to the central dome body,
and ease device onto the bracket, and attach
the side bolts to secure dome.
2.8.3 Cable Connection
P1 RJ45 Connector for Ethernet/PoE
P2 Reset
P3 Audio In
P4 Audio Out
P5 Alarm In
P6 Alarm Out
P7 RS485 (note + and – marked)
P8 AC24V (Red and Black) 0
0
103mm
120º
120º
[4.05"]
WARNING
2
2.8.4 Positioning Unit a) Optionally positioning cameras can be installed to
a pole mount bracket. The pole mount is a
universal bracket which also is suitable for other
PTZ series devices.
b) The positioning bracket then attaches to the pole,
using the supplied bolts.
c) If you are not using the pole mount, then the
bracket will attach to a stable surface / such as a
wall. It is essential you have a durable solid
surface due to the tension weight of camera when
connected.
d) You must also provide suitable cable access
through the bracket center.
e) Finally, a secure main camera body to the bracket. Care should be taken with the weight, and the cables will
need to be attached in advance. The install is a two-person operation due to the weight of device and time
which would be required to make the connections to the camera unit.
Note: You need to be sure connections of the four bolts are tight, and the washers are used as shown in the above diagram.
2
3. Performance
3.1 Generic Production Specifications
3.2 Camera Technical Specifications
PTZ Dome Range CAM-IPD-xx-xxx-DN Series. CAM-IPD-xx-xxx-IC. CAM-IPD-xx-xxx-IRL, CAM-IPD-xx-xxx-IR, Positioning PTZ CAM-IRZ-xx-xxx-IR. CAM-LTZ-xx-xxx-IRL
Model variations if available replace the xx-xxx with codes below.
Model Code Variation 2Z-36X 2Z-20X 2Z-40X 3Z-36X 8Z-36X
Image element 1/2.8 Type Exmor CMOS sensor 1/2.4 Type Exmor CMOS sensor
Total pixels 3.21M 2.13M 3M 8.51M
Low Illumination Color:0.05 Lux W/B:0.01Lux Color:0.05 Lux
W/B:0.01Lux Color:0.05 Lux W/B:0.01Lux
Optical zoom 20X 36X 40X 30X 30X
Lens 5-100mm 4.5-165mm 6.8-272mm 4.6-165mm 6-180mm
F-Stop F1.5(Wide)~F3.2(Tele) F1.6(Wide)~F5.5(Tele) F1.8(Wide)~F6.0(Tele) F1.6(Wide) ~ F5.5(Tele) F1.5(Wide) ~ F4.0(Tele)
Zoom speed 5.2s /7.0s 4.2s /6.0s 5.2s /7.0s 5.2s /7.0s 5.2s /7.0s
Digital zoom 16X 16X 16X 16X 16X
Wide Angle (W x H) 58.5°x 33.2° 60.5°x 35.1° 33.5°x 25.3° 60.5°x 35.1° 60.5°x 35.1°
Tele Angle (W x H) 3.1°x 1.7° 1.8°x 1.0° 1.2°x 0.7° 1.8°x 1.0° 1.8°x 1.0°
Min. Working distance 1m (Wide)2m (Tele) 1m (Wide)1.5m (Tele) 1m (Wide)2m (Tele)
Resolution(H*V) 1920×1080,1280×720 2048×1536,1920x1080 3840×2160,2592×1944
Main stream 1080P(1920×1080)/720P (1280×720) 3840×2160,2592×1944
Sub stream D1/VGA (640×480)/ QVGA (320×240) (1920×1080) / (1280×720)
Video frame rate 1 ~ 25fps (50HZ) 1 ~ 30fps (60HZ)
Video compression H.264/MJPEG
Audio compression G.711a/ G.711u
Comm. Interface Onvif 2.4 (TCP/IP) Visca protocol (TTL 3.3v) Pelco D protocol (TTL 3.3v)
WDR Range ON/OFF
Sharpness control 16 steps
Preset 128
S/N >50db
3D Noise Reduce 0-5, total 6 grade
BLC ON/OFF
Area Exposure / Focu
s
N/A
Electronic Shutter 1/30~1/10000
Day/Night Auto/Color/White & Black
Electrical Setting:
Power supply AC24V / PoE Baud rate (RS485) 2400/4800/9600/19200bps
Consumption Outdoor 30W Protocol PELCO_D
Decoder Built-in Address setting RS485: 0-254
Surge Buitt-in TVS4000V, Lighting Environmental:
Operation: Operational -10°C~+50°C (14°F~+122°F)
Pan rotation 360° continuously Environmental humidity 0-90% none compensation
Tilt rotation Tilt90°, with auto flip Protection grade IP66, Weatherproof housing
Rotation speed Pan0.4~320°/S Tilt0.4 ~150°/S Physical:
Preset 128 Presets Weight 6.1/6.8kg (13lb/14.9lb) (Model Dependant)
Surveillance Preset, Tour, Scan, Pattern Mount Wall, Pendant, Corner, Pole, Recess
3
3.3 Network IP Specifications
Support H.264/MJPEG/H.265 Video Compression, dual frame rate, high compression, high video quality
Support Micro SD card storage( need factory preset）
IP PT tile, date, time, frame rate
Support multi-network protocol: TCP/IP, UDP, RTSP, HTTP, DDNS, FTP, NTP, PPPOE, SMTP
Built-in web server, support IE explorer video watch, match specification, upgrade, User Rights Management
Built-in ONVIF protocol can make technology docking with another onvif platform, built-in SD card storage function
Support ONVIFonvif
ONVIF technology
docking
Compliant NVR: Dahua, HIKVISION, Zeno-tech
Compliant:nuuo, Digifort,milestone
Video compression H.264/ MJPEG
HD
Image resolution (main stream) 1080P(1920×1080)/720P(1280×720) 3MP / 8MP models support (2048x1536) / (3840x2140)
Image resolution (Secondary stream) D1/VGA(640×480)/QVGA(320×240)
SD
Image resolution (main stream) 704×576, 1-25 (30) fps/s; 640×480, 1-25 (30) fps/s
Image resolution (Secondary stream)
704×576, 1-25 (30) fps/s;640×480, 1-25 (30) fps/s 320×240, 1-25 (30) fps/s
Video Bitrate 32Kbps-16Mbps vary continious, support CBR/VBR
Info display
(featured product) Dome Title, Preset, Pattern, Scan, Zone, Zoom, Alarm, Date/Time G.711U, G.711A,
Audio compression Support 32K stereo
Audio compression Video/image/file
Saving Methods manual, auto(loop, timing, alarm switch volume, motion detection)
Protocol support TCP/IP，UDP, RTP, RTSP, RTCP, HTTP, DNS, DDNS, DHCP,
FTP, NTP, PPPOE, SMTP, UPNP
Web client viewing Support IE10.0 and over( built in Web Server), support 8.
4
4. Performance and Application
4.1 PTZ Performance and Features This intelligent PTZ comes with a smart design and a sturdy structure which is intended for a special occasion
and high-point monitoring. With built-in constant temperature device and wipers (if model supports), it can
dramatically enhance the usability in a broad variety environment. It also can contain multiple light source
for different applications and locations, with the low noise flexible rotation capacity and powerful functions
of the camera block, it will provide an excellent graphics for your customer.
Built-in receiver. o All configurable options stored in central control board to protect against power cuts. o Integrate design and high durability. o 128 presets can be randomly stored. o 01-80preset support auto-tour and each tour can save up to 16 presets. o Four pattern tours. o Four scans. o Built-in direction indicator o Built-in temperature indicator.
o Built-in clock setting function o RJ45 network interface, Min3.5 audio
interface. o RS485 Bus communication.
o One alarm input, one alarm output (relay normally open or normally closed)
Pan Tilt Feature o Aluminum alloy material and anti-violence design surface are well hidden, and rapid heat removal;
Level of protection achieves IP66. o Precise stepping motor drives the pan to run smoothly and react to sensitivity. o Integrated design, compact structure, easy to disassemble.
o Exquisite mechanical drive, support to rotate pan 360°continuously and tilt 0°~ +90° and may
rotate 180°with an auto flip.
o Pan 0.1°/s to rotate slowly, and the image doesn't vibrate.
Built-in digital camera o High sensitivity, high resolution, and integrated digital processing o Auto-focus o Auto-Iris o Auto brightness control o Auto white balance
o Auto backlight compensation o Auto slow shutter o Auto switch day/night
OSD menu o Webpage support English Language (Future revision may contain additional languages) o Visual OSD menu. Revising the PTZ's information and parameter by keyboard and OSD menu, and it
is easy to operate. o Set park action function and set presets, or run a scan, pattern, tour, etc. during idle time.
Internal temperature test o Set time display. o When the temperature exceeds the limit, the screen will display alarm information. o When the temperature is under the limit, the PTZ will delay to startup, and when the heating device
is heated and got higher than the low limit temperature to startup. o According to the temperature, the fan measures if it is to start or not and prolong the life of the fan.
Night View Function (optional feature on models with IR LED / Laser) o Select the different light source according to your need; this option will be not available if the PTZ
has no this function) o Can manual control or auto-control infrared LED ON/OFF, manual control through keyboard call 62
preset can turn infrared LED ON/OFF. If auto-control is working, image color will be a switch to black and white when in low brightness, black and white will be a switch to color when in high intensity.
2
Alarm in/out control function. On the IE interface, you can set the corresponding input and output functions, such as: receiving the alarm input signal can send a message can post an e-mail or capture pictures.
The items below describe the primary functions and the general principle of intelligence PTZ cameras. They may not refer to the particular operation methods of your device. A different system may have different operation methods.
4.2 Camera ID There is two eight-position dial switches SW1 and SW2 inside the PTZ housing, and SW2 is for setting
communication baud rate and controlling protocol. (For detail setting, please refer to DIP switch setting)
Besides the factory protocol (FACTORY), the PTZ is compatible with various popular protocols, such as
PECLO-D, PECLO-P, and customized protocol. See section 6.5 for further information about RS-485.
Any controlling command must base on the physical camera address, and the camera only answers to the
controlling command address which coincides with itself. There are three kinds of camera address:
Common address: Use the camera's switch number to set address 1-8 bits, the address range is 1-254.
Debug address: (Only factory protocol and PELCO can be set) if the camera ID is set 0, the user may select any address to control the PTZ. And there is also an IP address which the camera will respond to commands.
4.3 Auto-run motion Focus/speed proportion pan
When manually adjusting, for far focus situation, the PTZ responds at a high-speed so that touching rocker
slightly may make the picture move rapidly, thus causing the image to lose. To base on humanized design,
the PTZ automatically adjust pan and tilt rotation according to zoom near and far, which make it is
convenient to operate manually to make tracking for the object. In the menu, you may change system
parameter setting proportion pan as ON to run this function.
Auto flip
If the user holds the joystick in the down position, the camera rotates pan 180 degrees. In the menu, you
may set the system parameter setting AUTO FLIP as ON to run this function.
Park action
By the menu “park time” and “park action,” the user may set auto-call preset or run tour, pattern, and scan,
etc. after pointing a few minutes if the PTZ doesn't run any motions.
Power up action
By the menu “power up the action,” after the PTZ powers up or restarts, the user may set auto-resume
movements before power up and auto- call preset or run tour, pattern, and scan, etc.
4.4 Camera Control Magnification control
The user can control “Wide/Tele” to adjust zoom far and near of the image by keyboard controller to obtain
a panoramic image or close view that you need. The PTZ support digital zoom and optical zoom.
Focus control
The system defaults Autofocus. When the lens changes, the camera will auto-adjust focus according to the
center of the image to get a sharp image; the user can also manually focus to get the desired image by
operating keyboard “FAR/NEAR.” When operating keyboard joystick, camera resumes to autofocus.
The camera will be unable to autofocus in the following conditions:
o Target is not the center of the image.
3
o Observation of the target near and far at the same time, cannot be clear at the same time.
o Target is a strong light object, such as neon light, spotlight, etc.
o Target moves too fast.
o Target area such as a wall.
o Target is too dark or vague.
o The target image is too small.
Iris control
The system defaults Auto Iris. The camera can rapidly adjust the size of Iris, through the automatically induct the changing of environment ray, and thus make the brightness of deferent image stable. The user may adjust Iris by controller keyboard “open/close” to get required brightness that you need. The user also can resume auto Iris by joystick operation. When controlling the Iris manually, the PTZ locks current position you manually controlled; when operating joystick, the PTZ resume auto Iris.
Auto backlight compensation
Camera sub-area can carry out auto backlight compensation. Under a strong light background, the camera
will auto compensate light for the darker object and adjust daylight to the bright environment. To avoid
making the image lack fidelity by the back line is too bright, and the object is unable to be recognized
because of darkness, thus gain a clear image.
Auto white balance
The camera can automatically adjust white balance by the alteration of background lightness to reach a pure
color.
Thermal
Positioning units with a thermal part will feature a dual network camera device, and so a thermal image will
be encoded at the same position as the main zoom camera position. There is a minor offset of position due
to the thermal lens having a fixed focal length. This will vary depending on the chosen mm at the time of
purchase.
2
5. Network Configuration Network Connection brief
All PTZ cameras' factory default IP is 192.168.1.88, be sure you are on the correct network segment for
successful communications. Use static IP addresses for multiple PTZ devices, proper assignment of address
should be performed in advance of devices being physically installed to reduce potential conflicts or network
issues.
Users can modify the PTZ IP address through the quick configuration tool or via a web browser on the device.
5.1 Login Before login the camera, please confirm that the network segment of the camera and local PC is the same.
E.g., the IP address of the camera is 192.168.1.100, so the IP address of the local pc should be 192.168.1.xxx.
The default IP address of the camera is 192.168.1.88, so we should check the IP address of PC in the network segment 192.168.1.xxx or not. Start->Run->CMD, input the command ipconfig -all to verify the IP address of PC, if the IP in the 192.168.1.xxx as follows, so we can access the camera:
5.2 Download ActiveX plugin Run Internet Explorer (IE), enter the default IP address of the PTZ device.
Download and install ActiveX is required before any further steps can be undertaken.
ActiveX installing method:
Download installation will prompt you to run or download. You will be unable to enter the device settings
without the completion of this installation.
For each PC this will only be required once. So, to configure or set several devices, you will install ActiveX on
each PC which involves browser access.
Running the ActiveX part will be a set of prompts which will then proceed to install into your system.
3
5.3 Login Browser Using Internet Explorer (IE) with default address at URL. As a first security measure, you are prompted to set
a complex password. The help provided will provide the details of the minimal requirements.
5.4 Live Preview After successful login to the device, you will enter directly into the Liveview. The full selection of features of
PTZ is activated by clicking the icon at the top right as indicated below:
In the real-time browsing page, you can capture video images, video, playback, voice intercom, monitor,
clear the alarm, Log query, partial image enlargement, full-screen preview and cloud mirror control and
other operations.
[Master Stream] Retrieve the master stream of the device to view the video in real time to get the best
view.
4
[Secondary Stream] Retrieve the secondary stream of the device to see videos and reduce the network load.
[PTZ control] up, down, left, right, automatically adjust the PTZ rotation speed PTZ operation. As shown
below (Figure 3).
[Lens control] Zoom, focus, aperture, light, wiper, and other PTZ operations are available. The interface is
also on the primary control in (Figure 3).
[Preset Control] Presets can be set, called PTZ operation, click the inverted triangle below at bottom as
(Figure 3), Click the right triangle below will expand the options to present all additional options as shown
(Figure 4).
Figure 3 Figure 4
5.5 Client Search Tool Supplied on the provided CD with the product is the AV PTZ Tool. This application runs only on Windows PC
systems. You can run directly from the CD and does not require an install.
The tool will Search all PTZ / Positioning cameras. And IP settings / Time and firmware upgrades. Click the
Search will populate the found devices. Factory device has a username and password as admin. When you
first connect to the browser you are prompted to change password.
5
6. Appendix
6.1 Basic Operation Current-carrying to PTZ and Self-testing
The PTZ conducts self-testing after current-carrying, and it rotates slowly until displaying pan origin that is default setting, then moving to tilt origin, the lens is adjusted from far zoom to near zoom, then from near zoom to far zoom, when self-testing completes, there is relevant system information displaying on the screen, as follow:
S/N of the PTZ Firmware version Protocol PTZ ID Communication parameter
The information will not disappear until you stop to operate the system. If you set “power up action,” The PTZ will automatically activate motions after self-testing. How to perform the function? We will explain detail introduction in following passages.
Call the main menu The system enters the main menu by calling 95 preset or by calling nine preset twice within 3 seconds. All the menu setting is available from the main menu.
Menu and Keyboard operation:
o Keyboard operation:
[OPEN] when choosing pictures, it means to increase Iris; when setting menu, it means to enter the next menu or setting or means to save after setting. [CLOSE] when choosing pictures, it means to reduce Iris; when setting menu, it means to exit without saving the setting. [NEAR] Focus to near [TELE] Increase magnification [WIDE] Reduce magnification Joystick to up: When choosing the menu, it means to pick the former one; when selecting a picture, it means camera tilt up. Joystick to down: when choosing the menu, it means to select the next one; when selecting a picture, it means camera tilt down. Joystick to the left: when choosing the menu, it is equal with [CLOSE], when selecting a picture, it means camera tilt left. Joystick to the right: when choosing the menu, it is equal with [OPEN], when selecting a picture, it means camera tilt right. Press [TELE] and [WIDE] at the same time, it means 3D joystick rotates joystick cap.
o Menu Operation
“BACK”: Back to the former menu
“EXIT”: Exit to menu
“ ON”: Open some setting
“OFF”: Close some setting
6
6.2 Shortcut Keys PT unique shortcut keys as below. Functions are issued with preset from Browser or NVR devices. And
also, can be called via an RS485 connected keyboard.
Thermal shortcut keys (if products without thermal, no need to refer below) “ZOOM+” continuously clicking “+,” zoom is increasing uninterruptedly, zoom range from 1x to 8x “ZOOM-” continuously clicking “-,” zoom is reducing uninterruptedly, zoom range from 8x to 1x “FOCUS+” continuously clicking” +,” manual near focus uninterruptedly. “FOCUS-” continuously clicking”-,” manual far focus uninterruptedly. “IRIS+” click open “+” every time, the color code is switch once. “IRIS-” Soft press trigger autofocusing
In 3 seconds call 59 preset twice, and enter into the menu of the thermal camera. The following description for the buttons: ZOOM (+) upward cursor movement ZOOM (-) downward cursor movement FOCUS (+) go back superior menu FOCUS (-) enter submenu or go to current menu IRIS (-) save button
Set Call Function Description
N / Save No.N preset
/ N Call No.N preset
59 / Iris off
59 Iris on
51
/
Save horizontal scan left limit #1
52 Save horizontal scan right limit #1
53 Save horizontal scan left limit #2
64 Save horizontal scan right limit #1
51 Call horizontal scan #1
52 Call horizontal scan #2
53 Call preset cruise #1
54 Call preset cruise #2
55 /
Record pattern scanning #1
56 Record pattern scanning #2
57 Stop to record pattern scanning
55 Call pattern scan #1
56 Call pattern scan #2
61 or 62 Turn light on
61 or 62 / Turn light off
/
63 Start wiper（auto stop after 4times）
94 Reboot PT
95 Enter into menu
96 Factory default
163 Turn on off guardian function
164 Turn on preset guardian function
165 Turn on horizontal scan guardian function
166 Turn on cruise guardian function
131-150
/
E.g.: set+140+ preset, the time is
( 140-130)X 3=30seconds
Set free time of guardian function( num-150) x3minutes，
151-170 Set free time of guardian function(num-150) x3minutes, E.g:set+160+ preset, the time is (160-150)X 3=30minutes
7
6.3 Menu Index MAIN MENU
SYSTEM SETTING CAMERA SETTING FUNCTION SETTING WINDOW BLANKING EXIT
SYSTEM SETTING EDIT DOME LABEL INITIAL INFO DISPLAY SETUP MOTION CLEAR PASSWORD SETUP CLOCK SETTING COMM SETTING BACK EXIT
EDIT DOME LABEL
L：HD SPEED DOME BACK EXIT
INITIAL INFO FIRMWARE V1.23 6300
PROTOCOL：FACTORY
DOMEADDRESS：000
COMM：4800,N,8,1 BACK EXIT
DISPLAY SETUP DOME LABEL OFF PRESET LABEL OFF ZOOM LABEL ON ZONE LABEL OFF DIR. LABEL ON TEM. LABEL OFF TIME LABEL ON DATE LABEL ON BACK
MOTION AUTO FLIP ON PROPORTION ON PARK TIME 005 PARK ACTION SCAN POWER UP ACTION AUTO FAN ENABLED 045C TEMP C/F CENT ADVANCE SETTING BACK
CLEAR CLEAR ALL ZONES CLEAR ALL PRESETS CLEAR ALL PATTERNS CLEAR ALL TOURS CLEAR ALL WINDOWS FACTORY DEFAULTS RESTART BACK EXIT
PASSWORD SETUP OLD :****** NEW :****** CONF :****** ENABLE : OFF BACK EXIT
COMM SETTING S/N: 4JKAA7824000058 CONF: 4JKAA7824000058 SITE ID 001 COMM SPEED 4800BPS BACK EXIT
CAMERA SETTING ZOOM SPEED HIGH DIGITAL ZOOM OFF BLC MODE OFF SLOW SHUTTER OFF LINE SYNC N/A WDR MODE N/A ADVANCE SETTING1 ADVANCE SETTING2 BACK
ADVANCE SETTING1
B&W AUTO BLACK TIME N/A COLOR TIME N/A THRESHOLD 10dB MAX GAIN 08dB EXPOS. COMP ON MIRROR ON FLIP OFF NEXT
NEXT
SHARPNESS 005 PS SCAN OFF STABLE ZOOM OFF DNR OFF VIDEO MODE 1080I60 BACK EXIT
ADVANCE SETTING 2 AE MODE AUTO SHUTTER N/A IRIS N/A BRIGHT N/A WB MODE AUTO R GAIN N/A B GAIN N/A HI-RESOLU 018 BACK
ADVANCE SETTING
EIS ENABLED OFF PRESET FREEZE OFF AUTO FOCUS OFF DEFOGGER 015C HEAD UP ON BACK EXIT
FUNCTION SETTING PRESETS SCAN PATTERNS TOUR ZONES TIME RUNNING AUTO TRACKING BACK
PRESETS PRESET NUMBER 05 SET PRESET SHOW PRESET CLEAR PRESET AUTO TRACKING NONE EDIT PRESET LABEL BACK EXIT
SCAN
SCAN NUMBER 04 SCAN SPEED 50 SET LEFT LIMIT SET RIGHT LIMIT RUN SCAN CLEAR SCAN EDIT SCAN LABEL BACK EXIT
PATTERNS PATTERN NUMBER PROGRAM PATTERN RUN PATTERN CLEAR PATTERN EDIT PATTERN LABEL BACK EXIT
TOUR TOUR NUMBER 1 EDIT TOUR RUN TOUR CLEAR TOUR BACK EXIT
ZONES ZONES NUMBER 1 SET LEFT LIMIT SET RIGHT LIMIT CLEAR ZONE EDIT ZONE LABEL BACK EXIT
T
IME RUNNING DAY SAT TIME CHANNEL 1 START TIME 00:00 END TIME 00:00 RUNNING TOUR1 BACK EXIT
AUTO TRACKING DAY THU STATE OFF/TIME START TIME 00:00 END TIME 00:00 SENSITIVE MID TRACKING-ZOOM OFF TRACKING-SPEED MID TRACKING PARA BACK EXIT
WINDOW BLANKING WINDOW NUMBER 01 EDIT WINDOW ENABLE WINDOW OFF CLEAR WINDOW BACK
EDIT PRESET LABEL
L：PRESET 05 BACK EXIT
EDIT SCAN LABEL
L：AUTO SCAN BACK EXIT
EDIT PATTERN LABEL
L：PATTERN 1 BACK EXIT
EDIT TOUR PO-S-TM PO-S-TM 00-0-00 00-0-00 00-0-00 00-0-00 00-0-00 00-0-00 00-0-00 00-0-00 00-0-00 00-0-00 00-0-00 00-0-00 00-0-00 00-0-00 00-0-00 00-0-00 BACK EXIT
EDIT ZONE LABEL
L：ZONE 1 BACK EXIT
TRACKING PARA
SET LEFT LIMIT SET RIGHT LIMIT SET UP LIMIT SET DOWN LIMIT PARK TIME 000s PARK ACTION NONE BACK
EXIT
8
6.4 CAD Dimensions
6.4.1 Internal PTZ and D/N PTZ Models.
6.4.2 Laser LED and IR LED PTZ Models.
6.4.3 Positioning units
Pole Mount
215mm[8.46"]
4658m
m[2
2.2
"]
212mm[8.34"]
Wall Mount
378m
m[1
4.8
"]
346m
m
320mm[12.6"]
215mm[8.46"]
13.6
"][253m
m[9
.96"]
97m
m[3
.81"]
245mm[9.64"]
152mm[5.98"]
Recess Mount
200 mm[7.87"]
140 mm[5.51"]
200
mm
[7.8
7"
mm
312 mm
]
[17.5
"]
[16.3
"]
[12.3"]
445
mm
359m
m[1
4.1
"]
200mm
[7.87"]
Laser Light PTZ IR Led PTZ
Left Side Zoom Right Laser LED or Thermal
411mm
[16.8"]
273m
m
[10.7
"]
218mm[8.58"]
98mm
[3.85"]
175mm
[6.88"]
98mm
[3.85"]
9
6.5 RS485 Bus Basic Knowledge
Characteristics of RS485 Bus:
The connection of 120Ω termination resistor:
As specified by the RS485 standard, RS485 Bus is of half-duplexed data transmission cables with
characteristic impedance as 120Ω. The maximum load capacity is 32-unit loads (including the main
controller and controlled equipment.)
Transmission distances of RS485 Bus:
When the user selects the 0.56mm(24AWG) twisted pair wires as data transmission cable, the maximum
theoretical transmitting distance is as follows:
If the user selects thinner cables or installs the PTZ in an environment with strong electromagnetic
interference, or connects lots of equipment to the RS485 Bus, the maximum transmitting distance will be
decreased.
Connection and termination resistor
The RS485 standards require a daisy-chain Connection between the equipment. There must be termination
resistors with 120Ω (as Figure 6.6-1). Please refer to Figure 6.6-2 for simple connection. Note: “D” should not
exceed 7M (23feet)
Device terminal 120Ωresistance factory set inside the mounting base; there are two kinds of connection
mode for your option. Method 1, default connection, the jumper cap is in position2&3, this means 120Ω
resistance is not connected.
Inside the camera, the device has a mainboard as below, with a link to the termination of the RS485 bus.
This can be enabled by moving the jumper cap from position 2&3 to position 1&2. Care should be taken if
this feature is required. For normal operation on IP only use there will be no need for the opening of the
device.
Baud rate Max distance
2400BPS 1800m
4800BPS 1200m
9600BPS 800m
19200BPS 600m
10
7. Maintenance and Service
7.1 Limited Warranty The product will carry a two-year warranty.
The product will be obtained the free maintenance service if the same malfunction appears again within
three months.
Malfunction of products caused by force majeure (such as war, earthquake, lightning strike and so on),
abuse,
non-standard operation change of construction, non-normal wear or accident are non-free of warranty.
Please prevent the damage which is caused by heavy pressure, the excessive vibration.
Please use the original package or for transportation to prevent damage.
The maintenance services will not be free when the pan/tilt module is disassembled or serviced by the
user voluntarily.
To the products with defect: if it's in the period of warranty, please fill in the form of warranty
information correctly, describe the trouble in detail, and provide original sales. Invoice or its copy.
For the damage and loss which was caused by the user's specific application, the factory won't bear any
risk and responsibility. The factory compensation made by breach of faith, negligence or tortious won't
exceed the amount of the products. The factory won't bear any burden for the unique, unexpected and
continue damage caused by any other reasons.
Our company has the ultimate right of explanation for the above terms.
7.2 Warranty terms If the products are within the warranty time, the buyer should fill in the warranty card and send back
together with the products.
7.3 Warranty Shipping If the product needs repairing, you can return it to the manufacturer through the supplier or directly. If
you choose the later, please contact us to speed up the process. And our company only undertake the
one-way freight from manufacturer to customer after maintenance.
11
8. Regulatory Information
This equipment has been tested and found to comply with the limits for a class B digital device, under part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and if not installed and used by the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
The user is cautioned that changes and modifications made to the equipment without the approval of the manufacturer could void the user’s authority to operate this equipment.
8.1 EU Conformity Statement This product and - if applicable - the supplied accessories too are marked with "CE" and comply therefore with the applicable harmonized European standards listed under the Low Voltage Directive 2006/95/EC, the EMC Directive 2004/108/EC.
This product has been tested and complies with the Directive 2011/65/EU Restriction of Hazardous Substances.
2002/96/EC (WEEE directive): Products marked with this symbol cannot be disposed of as unsorted municipal waste in the European Union. For proper recycling, return this product to your local supplier upon the purchase of equivalent new equipment, or dispose of it at designated collection points. For more information, see www.recyclethis.info.
