IRM Control Systems - cdn.gep-water.comcdn.gep-water.com/GEP-download/en_GB/10.GEP Brochures/GEP...

IRM Control Systems RainwaterWoningbouw

Afkoppelen & infiltratie

Rainwaterutiliteitsbouw

DEHOUST Tanks

Grijswater

Afvalwater

Breaktanks

w w w . g e p - r a i n w a t e r . c o m

Utilize the possibilities of rainwater

DEHOUST Tanks

Grey Water

Waste Water

Breaktanks

Disconnecting & Infiltration

Drinking water

Rainwater

The brain of your rainwater system

www.gep-rainwater.com IRM control systems V 16.04 © GEP Tel. +32 (0)56/299.701 or +31 (0)183 610520

Rain

wat

er

2

IRM®-1 -Rainmanager RMS

• Electronic fully automatic controls• Maintenance-free corrosion proof four-stage self-

priming membrane pump• Built-in pressure controls• Integrated ‚internal supplementation‘ in accordance

with EN1717• Automatic water replacement• Motor-controlled valve for automatic switch to

drinking water• 18-litre maintenance-free pressure vessel• Provided with sound-insulating foam cover• Belgaqua and KIWA certificates

• Extremely energy efficient only 98 watts

• Very compact housing• Easy and quick to connect• Connections on one side • Suitable for bottom assembly• Includes complete connection set

with 8-litre pressure vessel

PrincipleThe IRM®-1 Rainmanager RMS works on the basis of IRM technology and is the intelligent brain of the rainwater system. The IRM®-controls monitor and control the entire rainwater system and guarantee continuous high reliability.

IRM®-1 Rainmanager RMS functions in accordance with the duplex principle, for which the integrated Rainmanager pump can be supplied with (rain)water from the rainwater tank or (drinking) water via the internal break tank of the Rainmanager depending on the tank’s water level.

Thanks to these two independent water flows, it is possible to keep the rainwater system in commission in case of an empty tank or for maintenance works in the large tank. This means that the system will be provided with water under all circumstances and at all tap points.

After a signal from the sensor or the manual switch, the IRM®-1 Rainmanager RMS automatically switches to drinking water. In this case, water is drawn from the

internal break tank. As such, just as much drinking water is supplemented as is actually used.

The principle of the IRM® philosophy truly is done justice. Guaranteed operation with optimum saving. Moreover, drinking water will never enter the large tank.

In accordance with EN1717, the IRM®-1 Rainmanager RMS is equipped with internal supplementation and can be placed above ground level without any problems. Installation below ground level is possible if the overflow is linked to a pump well with submersible pump that subsequently drains the water or if it is combined with a GEP water trap. The break tank of the IRM®-1 Rainmanager RMS is automatically refreshed so that still water is prevented.

Product Advantages

Description

Internals of the IRM®-1 Rainmanager RMS

* System not suited for connecting long-term automatic garden watering. Continued activation not longer than 20 minutes.Cut-out pressure can be set; factory settings at ca. 3.0 bar.

Specifications

IRM-1 Rainmanager RMS

Maximum flow Qmax 905 liter/h

Maximum suction lift H max 4,1 bar

Intelligent Regenwater Management

www.gep-rainwater.com IRM control systems V 16.04 3© GEP Tel. +32 (0)56/299.701 or +31 (0)183 610520

Art. No Description PG

402101 IRM®-1 -Rainmanager RMS incl. connection set 1

Accessories

402121 Level display of the current water level in rainwater tank 1

402122 Relay box for pump or automatic filter cleaning 1

402123 IRM®-Water lock 1/2“ 1

The pump of the IRM®-1 Rainmanager RMS is a special membrane pump; a four-chambered diaphragm pump that works according to the positive displacement principle. This principle through the four chambers provides a very energy-efficient effect. The pump controls switch on the pump as soon as there is a water demand. The connection set provides a pressure vessel, shut-off valves and flexible connections. Moreover, the pump operates at low voltage (24V). The combination of low voltage and energy efficiency ensures extremely low energy consumption. The IRM®-1 Rainmanager RMS’ control panel has the following features: On/Off switch, Drinking water/automated pump switch, LED indicators for automated pump, drinking water use, manual drinking water, pump on. The software in the IRM®-1 Rainmanager RMS has the following features: automatic water renewal for break tank, optional emergency overflow, reverse flow alarm and automatic dry running protection of the pump.

Energy-efficient Pump by IRM®-1 Rainmanager RMS• Switch box for supply pump • Level indicator• Connection set additional pressure

vessel• Switch box for automatic filter

cleaning• Switch box for external alarms

Pump characteristic

IRM®-1 -Rainmanager RMS

Height A 340 mm

Width B 340 mm

Depth C 279 mm

Drinking water connection D 1⁄2“

Suction pipe E 3⁄4“

Pressure pipe F 3⁄4“

Emergency overflow G 40 mm

Weight (empty) 6 kg

Specifications

Accessories

Price group UK

Connection diagram

All prices are excluding VAT and transport

Suction pipe 3/4“

IRM® -1 Rainmanager RMS

Drinking water 3/4“Overflow 40 mm

ConnectionTank

Pressure pipe 3/4“Assembly on solid floor.

bar

lit/min

CER TIFICAAT

pressure tank


Rain

wat

er

4

Inside of the IRM® -3 -Watermanager

IRM®-3 - Watermanager

Intelligent Rainwater Management

• Sound isolating foam housing• Automatic self-correction• Automatic adjustable filter cleaning• Automatic periodic water refreshing• Clear control panel with LED’s• Option for automatic water stop• High quality RC-pump from GEP• Sound isolating suspension system, with

shock absorbers• Suitable for GEP mobile phone-alarm• Suitable for back flow alarm• With integrated pressure display• All the connections are grouped at the

bottom to minimize the installation time

Product benefits

Description• Electronic full automatic control with IRM technology.• Multistage self priming centrifugal pump which is resistant to

corrosion, with pressure control and run-dry protection• Internal supplementation which is water hammer absorbing

and lime-resistant• Motor controlled ball valve for the switch to tap-water• Self controllable tap water floater with auto correctional

function• Integrated control pressure on manometer• Periodically refreshing of the water in the breaktank to prevent stagnant water• Belgaqua, DVGW and KIWA certified (in request)• Sound isolating and closed foam housing• Pump is placed on shock absorbers to reduce resonances• Product is suspended with the use of a

resonancereducingprofileDescriptionThe IRM Watermanager is a compact, plug and plug installatio for the usage of rainwater in a family home. The rainwater har-vesting system operates with the IRM technology and forms the intelligent brain of the rainwater harvesting system. The IRM control system monitors and controls the rainwater harvesting system and ensures a high operational reliability. The integra-ted pump of the IRM Watermanager can use (rain)water from the rainwater tank or (tap)water via the internal reservoir of the IRM Watermanager, this depends on the water level inside of the rainwater tank. Thanks to the IRM technology, it is possi-ble to retain two independent water flows (when the tank is empty or when there is maintenance required in the big rain-water tank). The IRM Watermanager automatically switches to tap water when the sensor or floater gives a signal, or when the system is manually switched. The IRM Watermanager now uses water from the internal water reservoir. This internal water reservoir is filled up with the amount which is actually required. This refill is done with a proportional valve to ensure a silent and calm water flow. This internal reservoir is build up from two compartments to reduce the sound of flowing water. The IRM Watermanager also contains a self-control function for the tap water floater with an auto correctional mode. The IRM Water-

manager tries to self-control, when there is a leakage in the valve. If this is futile, the IRM Watermanager will emit a visual and acoustic alarm.It is also possible to connect an additional valve in the tap water supply to allow the repair of the leaking pipe. The IRM control also automatically refreshes the water in the breaktank compartment. When the control system detects that the system is running on rainwater for a period of time, it will automatically flush the tap water pipes to prevent stagna-tion. The IRM control also makes sure that the rainwater filter is periodically cleaned, this is done by a strong pulsating water jet. This ensures the quality and durability of the rainwater filter. The duration and time interval of this water jet is adjustable on the IRM control system. The IRM Watermanager can also be connected to a back flow sensor which is placed in the rainwa-ter tank. The system automatically switches to (safe) tap water when back flow from the sewerage system occurs, the IRM con-trol also emits a visual and acoustic alarm. This prevents that tainted water comes into the pump, pipes, toilet floaters and taps. This switch is powered by a motor controlled ball valve. This ball valve can also be manually switched in order to ensure operational reliability.


Art.-Nr. Description PG

402112 IRM®-3 -Watermanager 1

Accessories

402119 GEP Supply pump for the IRM®-3 Watermanager 1

401158 GEP backflow sensor IRM®-Watermanagers 1

402132 Mobile phone alarm module 1

402275 Water stop for the IRM®-3 -Watermanager 1

Pump characteristics

Specifications

price group

Connection scheme


CER TIF ICAAT

Connection IN 3/4”

internalPower 900 Watt

Connection OUT 1” internal

Max. capacity 3,6 m³/h

Overflow Ø 75 RPM 2.900

Suction pipe 1‘‘ internal

Max. pressure 5,0 bar

Length in mm 662 Weight 23 kg

Height in mm 596 Temperature 5-35 °C

Width in mm 365 Capacitor 20 µF

Dimensions

Tap water IN

Greywater OUT

OverflowSuct

ion

pipe

230 V 50 Hz

Valve for filter cleaning

Status March 2016: Certificates requested

DescriptionThe IRM Watermanager consists out of a housing made of sound isolating foam this encloses the entire pump system. The internal break tank is equipped with an internal tap water refill, type AB, break and can be installed above ground level. Installation below ground level is possible when the (emergency) overflow is coupled to a pump pit or a GEP water stop. The IRM Watermanager is characterized by the following functions and characteristics; internal tap water refill based on demand, according to the EN1717, continuous operating of the rainwater system, function control, acoustic and visual signals during malfunctions, the possibility to manually switch the system to tap water, clear control panel with rotatable knobs, a pressure control with internal pressure tank, manometer, reset button and pump status display via LED lights, mo-tor controlled ball valve with manual control options, pump installation with shock ab-sorbers. Two-part foam housing which encloses the entire pump system, anti-vibration wall mounting via a rubber profile, all connections at the bottom of the unit and are equipped with a three-piece connection and a stop. Pump housing is made of stain-less steel and brass, thermal protection, integrated run-dry protection, tap water-, suc-tion- and pressure connection are equipped with a three-piece connection, automatic water refreshing after long operating periods, automatic control of filter cleaning, and potential-free contact for domotics or building control systems. The IRM Watermana-ger can also be equipped with an alarm which sends a text message, a supply pump in order to bridge long distances between tank and pump, a back flow alarm, a water stop for the tap water supply, or a water stop for the overflow.

• IRM 3 Watermanager with connection set consists out of; 1x resonance reducing wall bracket, 1x stop 3/4”, 1x stop 1”, floater switch with weight, mounting kit

• GEP supply pump set, necessary when suction pipe is longer than 15 meters

• GEP backflow sensor, detects back flow from the sewerage system, which allows the IRM Watermanager to switch to (safe) tap water

• GEP Water stop, closes the tap water pipe when there is leakage

• GEP mobile phone alarm, sends an alarm via a text message

Delivery specification and options


Rain

wat

er

6

IRM®-5 - Rainmanager

• Sound isolating foam housing• Automatic self-correction• Automatic adjustable filter cleaning• Automatic periodic water refreshing• Clear control panel with LED’s• Option for automatic water stop• High quality RC-pump from GEP• Sound isolating suspension system, with

shock absorbers• Suitable for GEP mobile phone-alarm• Suitable for back flow alarm• With integrated pressure display• All the connections are grouped at the

bottom to minimize the installation time

Product benefits

Description• Electronic full automatic control with IRM technology.• Multistage self priming centrifugal pump which is resistant to

corrosion, with pressure control and run-dry protection• Internal supplementation which is water hammer absorbing

and lime-resistant• Motor controlled ball valve for the switch to tap-water• Self controllable tap water floater with auto correctional

function• Integrated control pressure on manometer• Periodically refreshing of the water in the breaktank to prevent stagnant water• Belgaqua, DVGW and KIWA certified (in request)• Sound isolating and closed foam housing• Pump is placed on shock absorbers to reduce resonances• Product is suspended with the use of a

resonancereducingprofileDescriptionThe IRM Watermanager is a compact, plug and plug installatio for the usage of rainwater in a family home. The rainwater har-vesting system operates with the IRM technology and forms the intelligent brain of the rainwater harvesting system. The IRM control system monitors and controls the rainwater harvesting system and ensures a high operational reliability. The integra-ted pump of the IRM Watermanager can use (rain)water from the rainwater tank or (tap)water via the internal reservoir of the IRM Watermanager, this depends on the water level inside of the rainwater tank. Thanks to the IRM technology, it is possi-ble to retain two independent water flows (when the tank is empty or when there is maintenance required in the big rain-water tank). The IRM Watermanager automatically switches to tap water when the sensor or floater gives a signal, or when the system is manually switched. The IRM Watermanager now uses water from the internal water reservoir. This internal water reservoir is filled up with the amount which is actually required. This refill is done with a proportional valve to ensure a silent and calm water flow. This internal reservoir is build up from two compartments to reduce the sound of flowing water. The IRM Watermanager also contains a self-control function for the tap water floater with an auto correctional mode. The IRM Water-

manager tries to self-control, when there is a leakage in the valve. If this is futile, the IRM Watermanager will emit a visual and acoustic alarm.It is also possible to connect an additional valve in the tap water supply to allow the repair of the leaking pipe. The IRM control also automatically refreshes the water in the breaktank compartment. When the control system detects that the system is running on rainwater for a period of time, it will automatically flush the tap water pipes to prevent stagna-tion. The IRM control also makes sure that the rainwater filter is periodically cleaned, this is done by a strong pulsating water jet. This ensures the quality and durability of the rainwater filter. The duration and time interval of this water jet is adjustable on the IRM control system. The IRM Watermanager can also be connected to a back flow sensor which is placed in the rainwa-ter tank. The system automatically switches to (safe) tap water when back flow from the sewerage system occurs, the IRM con-trol also emits a visual and acoustic alarm. This prevents that tainted water comes into the pump, pipes, toilet floaters and taps. This switch is powered by a motor controlled ball valve. This ball valve can also be manually switched in order to ensure operational reliability.

Binnenwerk van de IRM® -3 -Watermanager



Specifications

Art.-Nr. Description PG

402113 IRM®-5 -Watermanager 1

Accessories

402129 Systempackage with supply pump 1

402124 IRM - Water stop 3/4“ 1

price group


Connection DN1 1” bi Power 1350 Watt

Connection DN2 1” bi Max. capacity 5,4 m³/h

Length in mm 662 Max. pressure 5,2 bar

Height in mm 596 Weight 23 kg

Width in mm 365 Temperature 5-35 °C

RPM 2.900 Capacitor 25 µF


Description

Connection scheme

The IRM Watermanager consists out of a housing made of sound isolating foam this encloses the entire pump system. The internal break tank is equipped with an internal tap water refill, type AB, break and can be installed above ground level. In-stallation below ground level is possible when the (emergency) overflow is coupled to a pump pit or a GEP water stop. The IRM Watermanager is characterized by the following functions and characteristics; internal tap water refill based on demand, according to the EN1717, continuous operating of the rainwater system, function control, acoustic and visual signals during malfunctions, the possibility to manually switch the system to tap water, clear control panel with rotatable knobs, a pressure control with internal pressure tank, manometer, reset button and pump status dis-play via LED lights, motor controlled ball valve with manual control options, pump installation with shock absorbers. Two-part foam housing which encloses the entire pump system, anti-vibration wall mounting via a rubber profile, all connections at the bottom of the unit and are equipped with a three-piece connection and a stop. Pump housing is made of stainless steel and brass, thermal protection, integrated run-dry protection, tap water-, suction- and pressure connection are equipped with a three-piece connection, automatic water refreshing after long operating periods, au-tomatic control of filter cleaning, and potential-free contact for domotics or building control systems. The IRM Watermanager can also be equipped with an alarm which sends a text message, a supply pump in order to bridge long distances between tank and pump, a back flow alarm, a water stop for the tap water supply, or a water stop for the overflow.

• IRM 3 Watermanager with connection set consists out of; 1x resonance reducing wall bracket, 1x stop 3/4”, 1x stop 1”, floater switch with weight, mounting kit

• - GEP supply pump set, necessary when suction pipe is longer than 15 meters

• GEP backflow sensor, detects back flow from the sewerage system, which allows the IRM Watermanager to switch to (safe) tap water

• GEP Water stop, closes the tap water pipe when there is leakage

• GEP mobile phone alarm, sends an alarm via a text message

Delivery specification and options

Dimensions

CER TIFICAAT

Tap water IN

Greywater OUT

OverflowSuct

ion

pipe

230 V 50 Hz

Valve for filter cleaning

Status March 2016: Certificates requested


Rain

wat

er

8

• Extremely silent operation• Very small, compact housing• High reliability thanks to IRM®

controls• Easy and quick to connect• RME: with water level indicator

internals of the IRM® -3 -Rainmanager RME

IRM®-3 -Rainmanager RME en RMC

Maximum flow Qmax 3,2m3/h

Maximum suction lift H max 44 m

Description• Electronic fully automatic controls• Maintenance-free, corrosion proof, multi-stage

membrane self-priming centrifugal pump with pump controls and dry running protection

• Integrated ‘internal supplementation’ in accordance with EN1717

• Proportional internal drinking water supplementation• Motor-controlled valve for automatic switch to

drinking water• RME: self-inspection drinking water float• Integrated dry running protection• Integrated systems pressure indicator• RME: automatic water renewal of break tank• RME: level indicator of current water level• RME: filter cleaning indicator• Belgaqua and KIWA certificates

PrincipleThe IRM®- Rainmanager RME works on the basis of IRM technology and is the intelligent brain of the rainwater system. The IRM®-controls monitor and control the entire rainwater system and guarantee continuous high reliability.

IRM®- Rainmanager RME functions in accordance with the duplex principle, for which the integrated Rainmanager pump can be supplied with (rain)water from the rainwater tank or (drinking) water via the internal break tank of the Rainmanager depending on the tank’s water level.


After a signal from the sensor or the manual switch, the IRM®- Rainmanager automatically switches to drinking

water. In this case, water is drawn from the internal break tank. As such, just as much drinking water is supplemented as is actually used. Moreover, the IRM®- Rainmanager has a self-inspection function of the float valve.


In accordance with EN1717, the IRM®- Rainmanager is equipped with internal supplementation and can be placed above ground level without any problems. Installation below ground level is possible if the overflow is linked to a pump well with submersible pump that subsequently drains the water.

Specifications

IRM®-3 -Rainmanager RME and RMC

Control pannel of the RME and RMC


Product Advantages



402103 IRM®-3 -Rainmanager RME incl. connection set 1

402102 IRM®-3 -Rainmanager RMC incl. connection set 1

Accessories

402128 Filter for drinking water supply 0,1 mm 1

402129 RME: supply pump 1

402122 Relay box for pump or automatic filter cleaning 1

The IRM®- Rainmanager RME is characterised by the following features and properties: needs dependent internal drinking water supplementation according to EN1717, continuous functioning of the rainwater system, function control, acoustic fault signal, possibility to switch the system to drinking water manually, permanently visible control panel, low-noise, vibration dampening, corrosion proof housing, integrated dry running protection, drinking water, input and output pipe equipped with three-part screw connections, automatic water renewal for long standstills, optional connection for supply pump, optic signal for filter cleaning, water level indicator.

Materials.Housing from recyclable EPP foam, break tank from synthetic material, magnet valve from high-quality brass, pump housing and impellers from stainless steel, pump input housing and output housing from α brass, pressure switch from synthetic PP.

IRM®-3 -Rainmanager RME.Compact rainwater system controls comprising of: electronic controls, integrated level indicator, maintenance-free, corrosion proof, multi-stage self-priming centrifugal pump, internal supplementation in accordance with EN1717, proportional needs dependent drinking water supplementation, motor-controlled three-way valve.

Description

• Connection set Rainmanager output side comprising of: 1 x brass T-coupling, 1 x water hammer absorber, 2 x flexible reinforced hose, 2 x brass adapter, 1 x 1m flexible hose.

• Connection set Rainmanager input side 1 x water filter, 1x brass three-way connection (see page 51)

• RME: system package with supply pump (see page 37)

• RME: potential free contacts• RME: reverse flow alarm (see page 50)• Filter for drinking water supply• RME: Computer/Domotica bus RS232• RME: Filter cleaning set

Pump characteristic

IRM®-3 -control system RME and RMC

Height A 580mm

Width B 380mm

Depth C 274mm


Suction pipe E 1“

Emergency overflow F DN 50 mm

Pressure pipe G 1“

Weight 18kg

Specifications

B

G

D

A

EF

C

Accessories

Price group UK

Connection diagram

Pressure pipe 1‘‘

Drinking water ¾‘‘

Connection tank

Suction pipe 1‘‘

Overflow 50 mm

IRM®-3 -Rainmanager


CER TIFICAAT


Rain

wat

er

10

• Extremely silent operation• High reliability thanks to IRM®-

Technology• Large pump capacity• With stagnation protection• Connection option for supply pump

Product Advantages

IRM® -5 -Rainmanager RM-5 (without isolating cover)

IRM®-5 -Rainmanager RM-5

Maximum flow Qmax 5 m3/h


Description

• Electronic fully automatic controls• Maintenance-free, corrosion proof, multi-stage

membrane self-priming centrifugal pump with pump controls and dry running protection


• Proportional internal drinking water supplementation• Motor-controlled valve for automatic switch to

drinking water• RM-5: self-inspection drinking water float• Integrated dry running protection• Integrated systems pressure indicator• RM-5: automatic water renewal of break tank• RM-5: level indicator of current water level• RM-5: filter cleaning indicator• Belgaqua and KIWA certificates

PrincipleThe IRM®-5 Rainmanager RM-5 works on the basis of IRM technology and is the intelligent brain of the rainwater system. The IRM®-controls monitor and control the entire rainwater system and guarantee continuous high reliability.

The IRM®-5 Rainmanager RM-5 functions in accordance with the duplex principle, for which the integrated Rainmanager pump can be supplied with (rain)water from the rainwater tank or (drinking) water via the internal break tank of the rain manager depending on the tank’s water level.


After a signal from the sensor or the manual switch, the IRM®-5 Rainmanager RM-5 automatically switches to

drinking water. In this case, water is drawn from the internal break tank. As such, just as much drinking water is supplemented as is actually used. Moreover, the IRM®-5 Rainmanager RM-5 has a self-inspection function of the float valve.


In accordance with EN1717, the IRM®-5 Rainmanager RM-5 is equipped with internal supplementation and can be placed above ground level without any problems. Installation below ground level is possible if the overflow is linked to a pump well with submersible pump that subsequently drains the water.

Specifications


IRM® -5 -Rainmanager RM-5



The IRM®-5 Rainmanager RM-5 is characterised by the following features and properties: needs dependent internal drinking water supplementation according to EN1717, continuous functioning of the rainwater system, function control, acoustic fault signal, possibility to switch the system to drinking water manually, permanently visible control panel, low-noise, vibration dampening, corrosion proof housing, integrated dry running protection, drinking water, input and output pipe equipped with three-part screw connections, automatic water renewal for long standstills, optional connection for supply pump, optic signal for filter cleaning, water level indicator.

MaterialsNoise insulating housing from recyclable EPP foam, break tank from synthetic material, magnet valve from high-quality brass, pump housing and impellers from stainless steel, synthetic pump input housing and output housing, pressure switch from synthetic PP.

IRM®-5 -Rainmanager RM-5Compact rainwater system controls comprising of: electronic controls, integrated level indicator, maintenance-free, corrosion proof, multi-stage self-priming centrifugal pump, internal supplementation in accordance with EN1717, proportional needs dependent drinking water supplementation, motor-controlled three-way valve.

Description

• Connection set Rainmanager RM-5 comprising of: 1 x brass T-coupling, 1 x water hammer absorber, 2 x flexible reinforced hose, 1 x brass adapter, 1 x 1m flexible hose.

• Optional supply pump. If the input pipe of the IRM®-5 -Rainmanager is longer than 15 metres, a supply pump must be installed that can be connected directly to the Rainmanager RM-5.

Pump characteristic


Height A 700mm

Width B 595mm

Depth C 305mm


Suction pipe E 1“

Emergency overflow F DN 75 mm

Weight 18kg

Specifications

C

AccessoriesConnection diagram


CER TIFICAAT

Pressure pipe 1‘‘

Drinking water ¾‘‘

Connection tank

Suction pipe 1‘‘Overflow 75 mm


402104 IRM®-5 -Rainmanager RM-5 incl. connection set 1

Accessories

402129 System Package with supply pump RM-5 1

402124 IRM - Water lock 3/4“ 1

Price group UK


Optional supply pump

A

B

E

D

E

F

RM-5

suct

ion

lift i

n m

flow in m3/h


Rain

wat

er

12

• Silent operation• Small, compact housing• High reliability thanks to IRM®

controls• Easy and quick to connect• Prefab assembly

Product advantages

Description

• Maintenance-free, corrosion proof, multi-stage selfpriming centrifugal pump with pump controls and dry running protection


• Proportional internal drinking water supplementation• Motor-controlled tap for automatic switch to drinking

water• Belgaqua and KIWA certificates

Principle

The IRM®- Rainmanager RMX works on the basis of IRM technology and is the intelligent brain of the rainwater system. The IRM®-controls monitor and control the entire rainwater system and guarantee continuous high reliability.

The IRM®- Rainmanager RMX functions in accordance with the duplex principle, for which the integrated Rainmanager pump can be supplied with (rain)water from the rainwater tank or (drinking) water via the internal break tank of the Rainmanager depending on the tank’s water level.

Thanks to these two independent water flows, it is possible to keep the rainwater system in commission in case of an empty tank or for maintenance works in the large tank. This means that the system will be provided with water under all circumstances and at all tap points.After a signal from the sensor or the manual switch, the IRM®- Rainmanager automatically switches to drinking

water. In this case, water is drawn from the internal break tank. As such, just as much drinking water is supplemented as is actually used. The machine is KIWA and Belgaqua certified.


In accordance with EN1717, the IRM®- Rainmanager is equipped with internal supplementation and can be placed above ground level without any problems. Installation below ground level is possible if the overflow is linked to a pump well with submersible pump that subsequently drains the water.

IRM®-Rainmanager RMX



Price group


402105 IRM -Rainmanager RMX Basic 1

IRM -Rainmanager RMX Advanced 1

402126 IRM -Rainmanager RMX connection set 1

402129 IRM -Supply pump for the IRM -Rainmanager RMX Advanced 1

UK


IRM®-System control RMX

Height 475 mm

Width 545 mm

Depth 340 mm

Drinking water connection 3/4“

Suction pipe 1“

Emergency overflow DN 75 mm

Weight 30 kg

Maximum flow Qmax 3,6 m3/h


Pump characteristic Specifications

Flow in m3/h

Max

imum

suc

tion

lift

RMX

Connection scheme


Rain

wat

er

14

The IRM® System Control TEA works on the basis of IRM technology and is the intelligent brain of the rainwater system. The IRM®-controls check, monitor and control the entire rainwater system and guarantee continuous high reliability.

The IRM® System Control TEA functions according to the duplex, implex or suplex principles for which the pump can be supplied with (rain)water from the rainwater tank or (drinking) water via the IRM® System Control TEA depending on the tank’s water level.


After a signal from the sensor or the manual switch, the IRM® System Control TEA automatically switches to drinking water. In this case, water is drawn from the internal break tank. As such,just as much drinking water is supplemented as is actually

used. The status can be read from the control panel of the IRM® controls. Moreover, the IRM® Control TEA also has a self-inspection function of the float valve. Possible faults are subsequently indicated optically and acoustically on the control panel.

The IRM® System Control TEA is equipped with internal supplementation and can be placed above ground level without any problems. Installation below ground level is possible if the overflow is linked to a pump well with submersible pump that subsequently drains the water.

IRM®-3/5 -System control TEA

• Needs dependent internal drinking water supplementation

• High reliability thanks to IRM® controls

• Self-inspection drinking water float

Product Advantages

insi

des

of th

e TE

A

Principle

Description• Electronic fully automatic controls• Internal supplementation • Proportional needs dependent on drinking water• Manual and automatic switching to drinking water• Motor-controlled valve for switching to drinking

water• KIWA certificationIRM® -system control TEA

control pannel TEA Intelligent Regenwater Management


Price group

Specifications

Connection diagram

Description

IRM®–System control TEA-3 TEA-5

supply capacity 3 m3/h 5 m3/h

Connection Drinking

water A

½“ bu ¾“ bu

Connection overflow B 50 mm 50 mm

Connection pump C 1“ bi 1“ bi

voltage 230 V / 50 Hz 230 V / 50 Hz

Dimensions(H x W x D)

610x355x280 mm

610x355x280 mm

Material housing recyclable PE recyclable PE

Material floater valve Plastic Plastic


402106 IRM®-System control TEA-3 with floater 1

402107 IRM®-System control TEA-5 with floater 1

Accessories

402127 Connection set TEA 1

402128 Filter for drinking water supply 0,1 mm 1

UK

IRM® System Control TEASystem control with needs dependent internal drinking water supplementation, continuous operation of the rainwater system, option to switch to drinking water manually, permanently visible control panel, float switch with 20 m cable, weight with plug, vibration dampening, motor-controlled ball valve 1“.

IRM®-Systemcontrol

Drinking water

Overflow 50mm

Suction pipe 1“

Pressure pipe 1“

Connection tank

E

610

mm

355 mm

A

B

C100 mm

135 mm

70 mm

340 mm

280 mm


Connection diagram with submerged pump

Accessories• Connection set TEA for a quick, reliable and vibration-free assembly comprising

of: 0.5 m flexible, anti-germinating hose 1”, brass couplings (2 hose grommets, 1 nipple, 1 t-coupling) and 2 hose clamps.

• Filter for drinking water supply


Rain

wat

er

16

The DBS system stands for Drinking water Bijvul Systeem (Drinking Water Replenishing System) with a submersible pressure pump. The multi-stage, water-cooled submersible pump distributes the water from the rainwater tank to the points of consumption via the controls. The pressure controls switch the pump on and off depending on flow and pressure. In case of a drop in pressure, the pump will automatically switch back on. As soon as the pressure is back to maximum, the pump will switch off again. Moreover, the pressure controls comprise of dry running protection that protects the pump against running dry. The actual operating pressure can be viewed on a manometer. In accordance with EN1717, the controls automatically fill the rainwater tank with drinking water as soon as it runs empty. The controls comprise of the following components: a float for level protection, a magnetic valve that opens the water mains if the float indicates a low level and a funnel that needs to be connected to the replenishment main to the rainwater well. Everything is pre-assembled on a handy wall console.

DBS Drinking Water Replenishing System


DBD Rainwater System with Submersible Pump


402201 DBD Rainwater System with Submersible Pump 1

402260 Connection set DBS Submersible Pump 1

402253 Submersible Pump revision set 1

Max. Capacity 3,0 m3/h

Connection Drinking water 1/2“

floater cabel 20 m

Max. pressure pump 3.4 bar

Refill funnel 50 mm

Connection Pressure pipe 3/4“

Connection pump 1“

power pump 900 W

Weight pump 12.6 kg

Specifications

CAUTION!No drinking water!


The DBS interior pump system stands for Drinking water Bijvul Systeem (Drinking Water Replenishing System) with an indoor pump. The controls make sure that the tank is partly replenished with tap water if the well is in danger of running dry. The controls comprise of the following components: a float for level indication, a magnetic valve that opens the water mains if the float indicates a low level and a funnel that needs to be connected to the replenishment main to the rainwater well. Everything is pre-assembled on a handy wall console. The pump can be used to connect 4 toilets, a washing machine and a maximum of three garden taps. The distance the pump can span on the output side is a maximum of 8 metres high and 30 metres long.

DBS Drinking Water Replenishing System with Indoor Pump


This self-priming centrifugal pump is intended for a horizontal set-up and is equipped with five impellers. The pump’s housing is made from brass and stainless steel. The interior is made from stainless steel and ceramic couplings developed especially for rainwater. The connections of the input and output side are 1” interior thread. The pump is delivered including a pressure switch for a pressure dependent activation/deactivation of the pump. Furthermore, the pressure switch is fitted with a manometer, LED indicator and dry running protection.

Description

Operation

Specifications


402202 DBS Drinking Water Replenishing System with Indoor Pump 3 m3/h 1

402203 DBS Drinking Water Replenishing System with Indoor Pump 5 m3/h 1

402254 Pomp connection set 1

Pump characteristic

DBS-3 DBS-5 DBS-3 DBS-5

Pump power 900 Watt 1.350 Watt Dimensions (HxWxL) 59 x 56 x 24 cm

Max. capacity 3,6 m³/h 5,4 m³/h Connection suction side

1“ bi

Max. pressure 5.0 bar 5.2 bar Connection pressure side

1“ bu

Drinking water supplementation

Connection 1/2” Weight 15 kg

Connection filling pipe

50 mm Condensator 16 µF

Photo: DBS rainwater system

Photo: DBS system including Connections

Photo: Detail of DBS

Price group UK

CAUTION!No drinking water!


Rain

wat

er

18

The RC-3 pump can be used to connect 4 toilets, a washing machine and a maximum of three garden taps. The RC-5 pump has more capacity: about 8 toilets and 5 garden taps. The distance the pump can span on the output side is a maximum of 8 metres high and 30 metres long for the RC-3 and 15 metres 40 metres respectively for the RC-5. This self-priming centrifugal pump is intended for a horizontal set-up and is equipped with four impellers. The pump’s housing is made from brass and stainless steel. The interior is made from stainless steel and ceramic couplings developed especially for rainwater. The connections of the input and output side are 1” interior thread. The pump is delivered including a pressure switch for a pressure dependent activation/deactivation of the pump. Furthermore, the pressure switch is fitted with a manometer, LED indicator and dry running protection.

RC 3/5 Self-priming centrifugal pump


1 intake coupling (1” interior) for the mains from the rainwater tank. The RC indoor pump takes in rainwater from the tank. The length of the intake mains between the RC pump and the tank cannot be longer than 15 metres.2 Output couplings (1” outer) for the mains to the toilets, washing machine and/or other tap points. The rainwater taken in leaves the pump through the pressure regulator.3 The pressure regulator ensures that the pump switches on if water is required and switches the pump off again is no more water is required. The manometer indicates the actual pressure in the mains system between the pump and the connected tap points. In order to use the pump, the intake mains and the pump well must be filled with water. This means that it is required to install a non-return valve in the intake mains. These are listed under pump accessories. which is also where you can find floating intake fixtures with non-return valves that ensure the intake of clear water.Trident filter technology inside

RC Self-priming Centrifugal Pump

Operation

Specifications

Dimensions


402207 RC-3 RC Self-priming Centrifugal Pump for rainwater 1


402254 Pump connection set 1

402255 Pumpconsole for wall construction for the rc-3/-5 1

DB-3 DB-5

Connection DN1

1” bi power 900 Watt 1350 Watt

Connection DN2

1” bi Max. capacity 3,6 m³/h 5,4 m³/h

Length L 409 Max. pressure 5,0 bar 5,2 bar

Height H 153 Weight 11.3 kg 11.5 kg

Width B 150 Temperature 5-35 °C

RPM 2.900 Condensator 20 µF 25 µF

Pump characteristic

Price group UK

1

2

3

Detail display


This self-priming centrifugal pump is intended for a horizontal set-up and is equipped with four or five impellers. The pump’s housing is made from brass and stainless steel. The interior is made from stainless steel and ceramic couplings developed especially for rainwater. The connections of the input and output side are 1” interior thread. The pump is delivered including a pressure switch for a pressure dependent activation/deactivation of the pump. Furthermore, the pressure switch is fitted with a manometer, LED indicator and dry running protection.

RC 8/9 Self-priming centrifugal pump


1 intake coupling (1” interior) for the mains from the rainwater tank. The RC indoor pump takes in rainwater from the tank. The length of the intake mains between the RC pump and the tank cannot be longer than 15 metres.2 Output couplings (1” outer) for the mains to the toilets, washing machine and/or other tap points. The rainwater taken in leaves the pump through the pressure regulator.3 The pressure regulator ensures that the pump switches on if water is required and switches the pump off again is no more water is required. The manometer indicates the actual pressure in the mains system between the pump and the connected tap points. In order to use the pump, the intake mains and the pump well must be filled with water. This means that it is required to install a non-return valve in the intake mains. These are listed under pump accessories. which is also where you can find floating intake fixtures with non-return valves that ensure the intake of clear water.

RC Self-priming Centrifugal Pump

Operation

Specifications

Dimensions




402256 Pump console for wall construction for the rc-8/-9 1

RC-8 RC-9

Connection DN1

1” bi Power 1700 Watt 2050 Watt

Connection DN2

1” bi Max. capacity 8,7 m³/h 8,7 m³/h

Length L 409 Max. pressure 5,3 bar 6,3 bar

Height H 153 Weight 11.3 kg 11.5 kg

Width B 150 Temperature 5-35 °C

RPM 2.900 Condensator 25 µF 40 µF

Pump characteristic

RC-8

RC-9

Price group UK

1

2 3

Detail display


Rain

wat

er

20

Specifications and Price group

GEP -Combipress 5-30 5-60 5-80

flow Q max. 4,5m3/h 5,2m3/h 5,4m3/h

suction lift H max 34m 58m 80m

Temperature in °C 0 - 35 0 - 35 0 - 35

Max. pressure 10 bar 10 bar 10bar

Max. Height 20m 40m 60m

RPM 2.800 2.800 2.800


402211 GEP -Combipress 5-30 complete including pressure control and TWIST, 1 meter 1



402214 GEP -Combipress 5-30 complete including pressure control and SAFF, 1 meter 1

Accessories

402253 Combipress Submersible Pump revision set 1

402260 Connection set Submersible Pump 1

GEP -Combipress 5-30 5-60 5-80

A (1~230V) 4,2 6,0 8,0

µF 230V 20 25 40

P2 (Kw) 0,6 0,9 1,2

Electrical data

Dimensions

these properties are based on a viscosity of 1mm

2/s and a specific w

eight of 1,000kg/m3.

IRM®–Combipress 5-30 5-60 5-80

A Height mm 436 504 584

B Width mm 194 194 194

C Pressure side 1“ bi 1“ bi 1“ bi

D Suction side 1“ bi 1“ bi 1“ bi

Weight kg 12,6 13,6 15,6

Fans 3 5 7


UK

Combipress Submersible Pump

DescriptionCombipress 5-40 including KIT-02Complete pump system for submerged set-up for implex rainwater systems that are equipped with IRM® system controls TEA or TEO comprising of: multi-stage submersible pressure pump, housing completely from stainless steel with output coupling of 1”, two intake connections of 1”, floating intake TWIST with 1 m hose, jacket-cooled squirrel-cage armature motor, protective class IP68, insulation class F, suitable for continuous operation, one-phased with thermal protection, pressure controls KIT-02, wall bracket for KIT-02 with corresponding assembly materials.

• Submersible pressure pump for continuous operation

• Extra wide base for stable placement• Handle for assembly• Includes 20 m cable H07• 2x ¼“ interior-connection on intake side for:

IRM® system controls and floating intake• 1” interior-connection on output side• Including pressure control KIT-02• Incl. floating intake TWIST with 1 m hose• Plug with capacitor

Description IRM® -Combipress

pressure control KIT-02

Materials• Pump well made from stainless steel AISI-304• Rotor made from stainless steel AISI-420• Noryl diffuser• Double axle seal of silicon-carbonate and

aluminium oxide/ceramic in oil-filled chamber• Control housing made from polypropylene

(PP) recyclable• Hose made from bacteriostatic thermoplast• Strainer and hose clamps made from

stainless steel


Com

bipr

ess

Subm

ersi

ble

Pum

p

submersible pump revision set

D

C

A

B


Specifications and Price group

GEP - Inpress 5-3 5-4 5-5

Flow Q max. 5,4 m3/h 5,6 m3/h 5,8 m3/h

Suction lift H max 34m 58m 80m

Depth max 10m 10m 10m

pressure max. 3,4 bar 4,4 bar 5 bar

Max. Height 20m 20m 20m


402215 GEP - Inpress 5-3 with integrated pressure control and TWIST 1 meter 1



Accessories

402253 Submersible Pump revision set 1

402260 Connection set Submersible Pump 1


A (1~230V) 3,0 4,0 8,0

µF 230V 20 25 40

P2 (Kw) 0,6 0,9 1,2

Electrical data

Dimensions

A

B


A Height mm 690 730 760

B Diameter mm 98 98 98

C Pressure side 1“ bi 1“ bi 1“ bi

D Suction side 1 1/4“ bi 1 1/4“ bi

1 1/4“ bi

Weight kg 10 11 12

Pump characteristic

UK

GEP - Inpress with built-in pressure controls

DescriptionThe GEP - Inpress submersible pump is a multi-stage, medium-cooled submersible pump for tank or ground water. The integrated pressure switch automatically switches on the pump on the basis of water demand. In case of water extraction, the pump will switch on, and in case of a sealed tap point, the pump will automatically switch off. A stainless steel strainer protects the pump against contamination. The new submersible pump concept combines proven pump technology with an advanced control system in a compact product that can be used immediately. Optionally, the pump can also be delivered as a well pump - without connecting a floating intake.

• Easy to assemble• Integrated pump controls, dry running

protection and non return valve• Only 10 cm in diameter• Water-cooled motor• Corrosion proof• Stainless steel intake filter• Includes floating intake

• Connection on the side for a floating intake. • Multi-stage submersible pumps mono block

pump with hydraulic part below the motor.• Built-in thermal protection.• Built-in electronic flow compensation monitor.• Synthetic impellers (POM).• Pump well made from stainless steel (AISI-

304).• Able to resist a maximum of 0.15% of sand.


D

C

Product Advantages

Technical Specifications


Rain

wat

er

22

Price group

The GEP Water Seal is a smart leak detection and water control system for use in homes. If the sensor contacts water, you will hear a loud buzzer. At the same time, the water supply will be switched off automatically. The GEP water seal comprises of a metal ball valve with motor drive. This is connected to the detector unit through a supple connection cord. The unit works on one standard 9 Volt battery and, as such, operates independently from the power grid. The GEP Water Seal can be used for rainwater systems that can be assembled below the sewerage level. (In the basement, for example) Naturally, it can also be used to protect rooms and equipment other than rainwater systems against water damage.

GEP Water seals


GEP Water Seal 1/2“

Specifications


402123 GEP Water seal 1/2“ 1

402124 GEP Water seal 3/4“ 1

402125 GEP Water seal 1“ 1

Water seal 1/2“ Water seals 3/4“ & 1“

Alarm Buzzer (92 dB) Buzzer (92 dB)

Detection build in moisture sensor single moisture sensor

Placement Standing or lying on the floor or

in mounting piece

Standing or lying on the

floor or in mounting piece

Height x Width x Depth 90 x 65 x 25 mm 110 x 65 x 45 mm

shut-off valve Motor controled water controled

Operations principle Swivel ball valve magnetic valve

Connection pipe 1/2“ 3/4“ or 1“

power supply 9 volt battery (included) 230 V / 50 Hz

Quality Mark CE CE 89/336 EWG

Connection mounting piece 50 mm 50 mm

The GEP Water Seals 3/4” and 1” are suitable for the protection of water mains with a diameter larger than 15 mm, such as, for example, the GEP Rainmanagers RM5, B-Class and C-Class. The GEP Water Seal is a complete set comprising of controls, a separate water sensor with 2 metres of cable, a magnetic valve and gaskets. An acoustic alarm will sound from the controls in case the sensor detects water. Moreover, the water mains will be sealed by the magnetic valve. Furthermore, there is the option of running the voltage supply of the equipment to be protected through the water seal. In case of an alarm, it will be automatically disengaged along with the acoustic alarm.

GEP Water Seal 3/4“ en 1“ GEP Water seal 1/2“

connection of the GEP Water seal 1/2“

Valve of the GEP Water seal 1/2“ on a Rainmanager RMC

GEP Water seal 3/4“ and 1“

To be placed near (preferably below) the rainwater system to be protected. The seal must be placed in the supply mains. Subsequently place the detector on the floor or in the mounting piece. Plug in the connection cord of the seal and the protection is ready. After hearing an alarm, press the reset button until you hear a beeping sound. You then hear a little motor that returns the valve in the open state. Apart from sealing the water mains, the water seals 3/4” and 1” have an additional function. These types also provide protection for electrical equipment. For instance, the rain manager on which the water seal is connected can be protected. In case of water detection, the voltage supply to the equipment in question is also disconnected; this does not only disconnect the water, but also the electricity.

Operation

UK


Drinking water supplementation sets


402204 Drinking water supplementation sets with 10 m kabel 1

402205 Drinking water supplementation sets with 20 m kabel 1


402206 Drinking water supplementation sets with level display 1


402252 Electronic level display 1

402251 Mechanical level display 1


Complete set for drinking water supplementation in the tank

in accordance with EN1717 comprising of:

• 1 x water hammer absorbing magnetised valve ½”, 230V, with 1.5 m of cable and

plug*

• 1 x feed funnel 50 mm

• 1x adapter plug, earthed with built-in socket

• 1 x float switch with 10 m of cable and weight

• 1 x marking sticker text ‘No drinking water’

Set can also be provided with a 20-metre cable.

Drinking Water Supplementation Set with Level Indicator

Complete set for drinking water supplementation in the tank according to EN1717. Water level display in the tank by means of a capacitive measurement, water level indication with LEDs in increments of 10% comprising of:

• 1 x water hammer absorbing magnetised valve ½”, 230V, with 1.5 m cable and plug*

• 1 x feed funnel 50 mm• 1 x LED-level indicator• 1 x sensor capacitive with 20 m cable

Level Indicator for Tanks

• Electronic current water level indicator in the tank by means of capacitive measurement. Water level indicator with LEDs in increments of 10%• Mechanical indicator of water level in the tank

Mechanical level display

Electronic level display

* Drinking water supplementation sets fill the tank with drinking water and some, contrary to most IRM® controls, are not fitted with an alarm that registers possible leakage of the magnetic valve. As such, regular inspection of the magnetic valve is required to prevent damage as a result of leakage. GEP is not liable for water damage or waste in such cases.

Drinking water supplementation sets with level display



GeenDrinkwaterwww.regenwater.com


Rain

wat

er

24


403651 Floating extraction TWIST Length 2m 2

403652 Floating extraction TWIST Length 3m 2

403653 Floating extraction SAFF Length 2m 2

403654 Floating extraction SAFF Length 3m 2

403655 Suction hose, flexible, spiral reinforced, 1“, roll of 30 meters 2

403656 Suction hose, flexible, spiral reinforced, 1“, roll of 15 meters 2

403657 Suction hose, flexible, spiral reinforced, 1“, per meter 2

403658 Suction set with filter basket and check valve, including hose nozzle and hose clamp. 2

Floating intakes TWIST and SAFF

Connection

When using the floating intakes TWIST and SAFF, the water is taken in 15 cm below the water surface which is where the purest water in a tank is located. In case of a low water level, the hose length prevents the strainer from falling to the bottom. This protects the pump against both floating dirt and sediment.

Materials• Brass tank feed-through• Spiral reinforced hose

made from bacteriostatic thermoplast

• Strainer and hose clamps made from stainless steel

• PP and brass foot valve• PE floater• Stainless steel spiral

• Simple and quick to install• No bacterial growth• Intake of the purest water

Product Advantages

Operation

With 2 or 3-metre hose. Set for a flexible floating intake from the tank, completely assembled, comprising of:• 1 x stainless steel strainer

with mesh size of 1 mm TWIST and 0.44 mm SAFF, with floater and mounting bracket

• 1 x 2 m anti-germinating hose 1” with hose grommet with built-in foot valve

• 1 x brass tank feed-through 90° corner piece with hose grommet including clamping ring

The special tank feed-through prevents friction forces of the weight so that the water resistance remains intact; even after multiple years.

Description

PG-swivel

Tank connectioncap

PE-screw connection

TWIST SAFF

TWIST: for systems with a pre-filter

SAFF: for systems without a pre-filter

Accessories: hose clamp, floater


Floating dirt

Sediment layer

casing tube

supply

Siphon with

clamp

drainage

with check

valve

floating extraction SAFF


Fine Filter Carbon Filter Set TRIO


402305 Fine filter carbon filterset Trio 1

401155 Automatic time controled filter cleaning 1/2” 1

402306 Filter element Triofilter 10 µm with carbon 1

402307 Filterelement Triofilter 25 µm 1

402301 GEP Fine filter 3/4” 1

402302 Filter Cartridge GEP Fine filter 3/4” 1

402303 GEP Fine filter 6/4” 1

402304 Filter Cartridge GEP Fine filter 6/4” 1

Fine Filter Carbon Filter Set TRIO

Collected filtered rainwater is suitable for flushing the toilet, for use in the washing machine and in the garden. For more high-quality applications, it is sometimes wise to install an additional fine filter. The GEP Trio filter set is a filter that ensures that the collected rainwater achieves a high, sound quality level. Thanks to the self-cleaning/back-flushing of the pre-filter, particles up to 90 micrometer are collected in the first element and flushed away (automatically). The second element collects particles up to 25 micrometer and the last element collects particles up to a size of 10 micrometer. The final filter element also contains carbon (activated carbon), which also removes bad odours and colour from the water.the GEP Trio filter set contains a discharge siphon, which makes sure that the water in the system is not contaminated by reverse flow in accordance with the European standard EN 1717. The reverse flow is protected because the filter elements have been placed behind an (electro-magnetic) tap valve.The three-stage filter is made with a unique three-fold housing that ensures the system is sound, safe and compact.

Filter carbon filterset Trio


• Simple and quick assembly• Low maintenance• Also for existing renovation

construction• No bad odours and colours• Self-cleaning fine filter

Product Advantages

Technical data and Specifications

Height A in mm 420

Length B in mm 336

Width C in mm 107

Flow at 3 bar (m³/h) 2,8

Inlet pressure Min. 1,8 bar \ Max. 8,0 bar

Temperature Max. 45°C

Connections 1“

Mesh size 90 µm - 25 µm - 10 µm

Weight 3 kg

Special properties: The TRIO is created out of one piece, which means there are no leaks. The TRIO comprises of three components that provide optimum protection: first filter for a pre-filter of 90µm (washable cartridge), second filter with a finer filtration of 25µm, third filter for an even finer final filtration of 10µm including activated carbon element that remove odour and colour from the rainwater. Wall bracket for assembly and wrench to make replacing cartridges easier are included.

GEP Fine filtersFine filter filters the small particles out of the water. The filter cartridge can be removed and is easy to clean or replace, provided with non-return valve. Filter is quick and easy to inspect through transparent, UV-protected impact-resistant filter housing. Specifications Fine filter ¾” Maximum debit: 3,000 L/h, rating: 50 micron, Nominal work pressure 10 bar, max. Temperature 60 degrees Celsius. Specifications Fine filter 6/4” Maximum debit: 4,000 L/h, rating: 80 micron, Nominal work pressure 16 bar, max. Temperature 40 degrees Celsius.

GEP

fine

filte

r


Rain

wat

er

26

IRM® - Rainwater for Utility and Industrial Construction

GEP provides rainwater systems for the utility and industrial construction. In principle, we distinguish between two types of systems; the self-priming rainwater systems and the rainwater systems with supply pump. The self-priming models on average are suitable for buildings with a roof surface up to ca. 1,700 m2 and a maximum debit up to 10m3/h. The IRM Rainmanagers

type B-Class and C-Class Compact C are such systems. Because of reliability, the pump capacity is doubled and these systems have an integrated switch to tap water. In case there is insufficient rainwater in the rainwater well, tap water is pumped into the internal break tank. This means that the large rainwater wells are not filled with valuable tap water. The IRM-Rainmanager saves more water and guarantees higher reliability than traditional systems with drinking water supplementation in the rainwater tank. Naturally, all these machines are KIWA and Belgaqua are certified. The Rainmanager checks, monitors and controls the entire rainwater system and guarantees continuous high reliability.

CER TIFICAAT

IRM®-6 Rainmanager B-Class


Floating extraction TWIST


GEP’s rainwater systems that are equipped with a supply pump are suitable for the relatively large rainwater systems in the utility and industrial construction. For instance, roofs up to 10,000 m2 and debits up to 100 m3/h. The IRM Rainmanagers A-Class, C-Class, D-Class and E-Class are such systems. These IRM rain managers comprise of a steel box with integrated break tank and double

pump system. This break tank is supplied with water from the large tank by means of a supply pump. The double pump system in the Rainmanager provides enough water pressure to the tap points. In case there is insufficient rainwater in the rainwater tank, tap water is pumped into the break tank. This means that the large rainwater wells are not filled with valuable tap water. The IRM-Rainmanagers save more water and guarantee higher reliability than traditional systems with drinking water supplementation in the rainwater tank. Naturally, all these machines are KIWA and Belgaqua are certified. The Rainmanager checks, monitors and controls the entire rainwater system and guarantees continuous high reliability.

CER TIFICAAT


IRM®-10 Rainmanager C-Class GEP supply pump

IRM®-Rainwater System with Supply Pump


Rain

wat

er

28

Price group

IRM®- 6 Rainmanager B-Class

Width in mm 550

Depth in mm 650

Height in mm 850

Weight (empty) 60 kg

Suction pipe 2 x 1” bi

Pressure pipe 1¼”

Overflow in mm 2 x 75

Drinking water 2 x ¾”

Floater cabel 20 m

Power 1,6 kW

Max. flow 8 m3/h

Max. Suction lift 20 m

Max. pressure 3,5 bar

Voltage 230V/50Hz

Weight (empty) 60 kg

Materials: cover of PS, Breaktank of PE, Console of galvanized steel, pump console PP


402601 IRM®-6 -Rainmanager B-Class 4

Accessories

402702 Connection set B-Class 4

402706 Supply pump for the B-Class 4

402710 level sensor for the B-Class 25 meter 4

401158 Back flow protection 2

B-Class with supply pump

The IRM®-6 Rainmanager B-Class is a complete system for bottom installation with IRM® controls, integrated disconnection tank and built-in double pump system. The IRM® controls control the water levels in the disconnection tank and the large rainwater well. The controls also provide for cascade control and an operation hours schedule for the pumps. Lacking rainwater, system fault or manual operation, the system will switch back to the disconnection tank. The drinking water is supplemented into the disconnection tank through a special proportional float. This happens in a reliable manner in accordance with EN1717 and the machine as such is Belgaqua and KIWA certified.

The switch to municipal water can also take place manually. The municipal connection is fitted with stagnation protection that automatically refreshes the water in the machine every 10 days. The potential free contact makes a connection to automated and building management systems possible. Fitted with automatic filter cleaning controls.

Description

Specifications

UK



IRM® -6 -Rainmanager RM-6


Connection diagram

* If the distance between B-Class and rainwater tank is larger than 15 metres, an additional supply pump must be used. (Optio-nal) The controls of the B-Class provide control of the automatic filter cleaners of the Trident rainwater filters.

*

Installation

Drinking water 1 min. ¾‘‘

Drinking water 2 min. ¾‘‘

Suction pipe 1 min. 1‘‘

Suction pipe 2 min. 1‘‘

Emergency overflow 1 min. 75

Emergency overflow 2 min. 75

Pressure pipe min. 1‘‘

Cabels of the B-Class

Digital display B-Class

CER TIFICAAT


Rain

wat

er

30

IRM®- 8 Rainmanager C-Class Compact C

Principle

The IRM® controls with micro-processor of the GEP CompactC checks, monitors and controls the entire rainwater system and guarantees continuous high reliability.

For the hybrid rainwater system, the rainwater is pumped from the large tank to the system tank. From this system tank, a double pump system provides water to the tap points. Drinking water supplementation takes place in the system tank. This means drinking water never reaches the large tank.

Thanks to these two independent water flows, it is possible to keep the rainwater system operational in case of an empty tank or for maintenance works in the large tank. Thus, the hybrid system is always operational, even without the large tank.The reliability can be increased even further in combination

with a GEP overflow trap with an alarm. In case of reverse flow from the sewer, the system will automatically switch to drinking water and the fault will be indicated optically and acoustically by means of the GEP CompactC.

After a signal from the level indicator, the alarm or the manual switch, the GEP CompactC IRM® system controls automatically switch to drinking water. In this case, (drinking) water is drawn from the break tank. The status and water level can be read from the control panel of the IRM® controls. The controls furthermore provide control of the automatic filter cleaners of the Trident rainwater filters.

The principle of the IRM® philosophy truly is done justice. Guaranteed low-maintenance operation with optimum saving and drinking water will never enter the large tank.

GEP C- Class Compact C with internal pump installation, breaktank, IRM®- system-control, prefab inwstalled in steel housing

Product Advantages

• Double pump system with self-priming pumps. • Cascade controlled.• Possibility of connecting an additional (second) supply

pump to (possibly) use two different rainwater wells.• Optionally available as self-priming system (without

supply pump, type SA)• Electronic controls with four-line LCD-display.• Operation hours counter for every pump.• Pressure indicator for the system.• Level indicator of the water level in the rainwater well.

(optional)• Manual switch to tap water is possible.• Potential-free alarm• RS232 bus connection• Prefab assembly in box made from enamelled steel.• Control of automatic filter cleaners.

Description

• Very small and compact• Internal supplementation in accordance

with EN1717• Optimum reliability thanks to IRM®

controls• Ready for immediate operation, prefab

assembly, including double pump system

Digital LCD-Display

Max. flow in m3/h 8,0

Max. pressure in bar 3,0 of 5,0

Voltage 230V/50Hz

Max. power usage A 2 x 3,0 A of 5,0 A

Max. Power in Watt 2 x 650 of 1.100

Technical data

Protection class IP44

Security class EN1717 type AA

Voltage 9V DC

Standby usage 3,5 watt

housing metal coated steel



Price group

Width mm 570

Depth mm (with door) 630

Height mm (without adjustable feet) 1.325

Weight empty in kg 90

Weight full in kg 190

Pressure pipe 1 1⁄2“ bu

Drinking water connection 5/4“ bu

Supply pump 5/4“ bu

Emergency overflow 110 mm

Supply Voltage 230V

Dimensions CompactCDescription

Accessories

• C-Class supply pump• Automatic filter cleaning module• Reverse flow protection • Domotics connection set• Level indicator• Water trap

The CompactC is built into a steel box and the integrated break tank is supplemented with water from the large tank by means of a supply pump. In case of an empty tank, the break tank is supplemented with drinking water. The double pump system in the CompactC provides water pressure from the break tank to the tap points. The IRM® system controls of the GEP CompactC provide level indication of the tank, automatic controls of the pumps and automatic drinking water supplementation.Moreover, the controls have the following protections:checking and setting switch points, checking number of operation hours, automatic system check with acoustic and optic alarm, reverse flow protection, pump motor protection, potential-free contacts, possibility of switch to drinking water manually, checking optional level sensor, setting operation with one or two independent rainwater wells.Prefab built-in break tank with integrated smoothing inlet, emergency overflow, magnetic valve with water hammer

absorber and internal supplementation.Compact housing with output side and overflow can be connected to both left and right side so placement in small room is possible. Everything is KIWA and Belgaqua certified. The system controls also provide the option of working with two independent rainwater wells. Rainwater well 1 is supplemented from rainwater well 2 between 30 and 50 %. The SP types are self-priming and thus function without supply pump.

Double pump system with:• Independent commissioning • Manual individual pump test• Dry running protection• Duration protection • Operation hours division over the

pumps• Cascade controls of the pumps• Configurable engage and

disengage pressures• Control of automatic filter cleaners



UK


402602 IRM®- 8 Rainmanager C-Class CompactC 8-30 4

402603 IRM®- 8 Rainmanager C-Class CompactC 8-50 4

402604 IRM®- 8 Rainmanager C-Class CompactC 8-30 SP 4

402605 IRM®- 8 Rainmanager C-Class CompactC 8-50 SP 4

Accessories

402707 Supply pumpset C-Class 4

402710 Level sensor 25 meter 4

402712 Non-return valve for C-Class 4

402703 Connection set C-Classe 4

CER TIFICAAT


Rain

wat

er

32

PrincipleThe IRM® controls with micro-processor of the IRM®-10 Rainmanager C-Class checks, monitors and controls the entire rainwater system and guarantees continuous high reliability.


Thanks to these two independent water flows, it is possible to keep the rainwater system operational in case of an empty tank or for maintenance works in the large tank. Thus, the hybrid system is always operational, even without the large tank.

The reliability can be increased even further in combination with a GEP overflow trap with an alarm. In case of reverse flow from the sewer, the system will automatically switch to drinking water and the fault will be indicated optically and acoustically by means of the IRM® -10 Rainmanager C-Class.

After a signal from the level indicator, the alarm or the manual switch, the IRM® system controls IRM®-10 Rainmanager automatically switch to drinking water. In this case, (drinking) water is drawn from the break tank. The status and water level can be read from the control panel of the IRM® controls.

The principle of the IRM® philosophy truly is done justice. Guaranteed operation with optimum saving and drinking water will never enter the large tank.

Type C-Class C-Class

6-40

C-Class

6-50

C-Class 8-40

C-Class 8-50

C-Class 14-40

Max. flow per pump m3/h 3,5 3,5 4,8 4,8 7,2

Max. flow submersible pump m3/h ca. 6 ca. 6 ca. 9 ca. 9 ca. 14

Max. Suction lift m 42 52 42,2 57,7 47,3

Power per pomp Watt 2 x 700 2 x 950 2 x 880 2 x 1.200 2 x 1.200

Technical data

IRM®-10 -Rainmanager C-Class with internal pump installation, breaktank, IRM®- system control in steel housing

Product Advantages

• Electronic IRM® controls with micro-processor• Integrated internal supplementation in accordance

with EN1717• Drinking water supplementation up to 10 m³/hour

with water hammer absorber• Integrated level indicator for large tank• Automatic and manual switch to drinking water use• Automatic water renewal of break tank• Electronic check of the filling pump and the magnetic

valve• Potential-free output for alarm indicators• Can be connected to alarm trap GEP RSW• Hybrid break tank with smoothing inlet• Can be connected to level dependent automatic filter

cleaning• Systems pressure indicator

Description

• Internal supplementation in accordance with EN1717

• Optimum reliability thanks to IRM® controls

• ready for immediate operation, prefab assembly, including double pump system

control pannel

CER TIFICAAT

IRM®-10 -Rainmanager C-Class



Price group

Width mm 570



Electrical security 20A

Max. flow 14m3

Suction lift max. 56m

Pressure pipe 5/4“ bi

Drinking water connection 1“ bu

Supply pump 5/4“ bi

Breaktank 100 l


Dimensions C-ClassDescription

Accessories• C-Class supply pump• Automatic filter cleaning module• Reverse flow protection • Domotics connection set• Water trap• Computer LON-Bus RS232

The IRM®-10 Rainmanager C-Class is built into a steel box and the integrated break tank is supplemented with water from the large tank by means of a supply pump. In case of an empty tank, the break tank is supplemented with drinking water. The double pump system in the IRM®-10 Rainmanager C-Class provides water pressure from the break tank to the tap points. The IRM® system controls of the IRM®-10 Rainmanager C-Class provide level indication of the tank, automatic controls of the pumps and automatic drinking water supplementation.Moreover, the controls have the following protections:checking and setting switch points, system check with acoustic and optic alarm, reverse flow protection, pump motor protection, potential-free contacts, possibility of switch to drinking water manually, checking level sensor

Connections:• computer LON-Bus RS232• Level dependent control of

automatic filter cleaning

Prefab built-in break tank with integrated smoothing inlet, emergency overflow, magnetic valve 1” with water hammer absorber and internal supplementation.

Double pump system• Automatic self-calibration of the

engage and disengage pressure• Continuous independent

calibration of the switch points• Indicator of pressure by means of

LEDs• Manual individual pump test• Dry running protection• Duration protection (if the pump is

engaged for longer than 15 min., it will be disengaged for a short time; if the pressure lowers, the pump will be engaged again and if the pressure remains the same, automatic calibration will take place)

• Automatic equal operation hours division over the pumps

• Cascade controls of the pumps

6-406-50 8-40

8-50

14-40

Suct

ion

lift i

n m

Flow in l/min



UK


402606 IRM®-10 -Rainmanager C-Class HY 6-40 including double pump installation 4





Accessories

402707 Supply pump voor A/C-Class 4

402712 Non-return valve C-Class 4

402703 Connection set C-Classe 4


Rain

wat

er

34

IRM®- 14 Rainmanager D-Class

Principle

The IRM® controls with micro-processor of the GEP D-Class checks, monitors and controls the entire rainwater system and guarantees continuous high reliability.


Thanks to these two independent water flows, it is possible to keep the rainwater system operational in case of an empty tank or for maintenance works in the large tank. Thus, the hybrid system is always operational, even without the large tank.The reliability can be increased even further in combination with a GEP overflow trap with an alarm. In case of reverse

flow from the sewer, the system will automatically switch to drinking water and the fault will be indicated optically and acoustically by means of the GEP D-Class.

After a signal from the level indicator, the alarm or the manual switch, the GEP D-Class IRM® system controls automatically switch to drinking water. In this case, (drinking) water is drawn from the break tank. The status and water level can be read from the control panel of the IRM® controls. The controls furthermore provide control of the automatic filter cleaners of the Trident rainwater filters.


GEP D- Class with internal pump installation, breaktank, IRM®- system control in steel housing

Product Advantages

• Double pump system, horizontal centrifugal pumps • Cascade controlled• Possibility of connecting an additional (second) supply


supply pump)• Electronic controls with four-line LCD-display• Operation hours counter for every pump• Pressure indicator for the system• Level indicator of the water level in the rainwater well.

(optional)• Manual switch to tap water is possible• Potential-free alarm• RS232 bus connection• Prefab assembly in box made from enamelled steel• Control of automatic filter cleaners

Description



• Ready for immediate operation, prefab assembly

Digital LCD-Display

CER TIFICAAT

Max. flow in m3/h 14

Max. pressure in bar 5,8

Voltage 230V/50Hz

Max. power usage A 2 x 6,5 A

Max. Power in kW 2 x 1.360

Technical data

Protection class IP44


Control Voltage 9V DC




Price group

Width mm 800





Pressure pipe 1 1⁄2“ bi

Drinking water connection 5/4“ bu

Supply pump 5/4“ bi


Dimensions D-ClassDescription

Accessories• D-Class supply pump• Reverse flow protection • Non-return valve• Connection set• Water trap

The GEP D-Class is built into a steel box and the integrated break tank is supplemented with water from the large tank by means of a supply pump. In case of an empty tank, the break tank is supplemented with drinking water. The double pump system in the GEP D-Class provides water pressure from the break tank to the tap points. The IRM® system controls of the GEP D-Class provide level indication of the tank, automatic controls of the pumps and automatic drinking water supplementation.

Moreover, the controls have the following protections:checking and setting switch points, system check with acoustic and optic alarm, reverse flow protection, pump motor protection, potential-free contacts, possibility of switch to drinking water manually, checking level sensor

Connections:• computer LON-Bus RS232• Water trap• Level dependent control of

automatic filter cleaning


Double pump system with:• Independent commissioning • Continuous independent

calibration of the switch points• Pressure indicator on LCD Display• Manual individual pump test• Dry running protection• Duration protection (if the pump is



• Cascade controls of the pumps• Control of automatic filter cleaners

14-60

Suct

ion

lift i

n m

Flow in m3/uur



UK


402611 IRM®- 14 Rainmanager D-Class 14-50 4

402612 IRM®- 14 Rainmanager D-Class 14-60 4

402613 IRM®- 14 Rainmanager D-Class 14-50 SP Self-priming 4

402614 IRM®- 14 Rainmanager D-Class 14-60 SP Self-priming 4

Accessories

402708 Supply pump for the IRM®- 14 D-Class 4

402713 Non-return valve D-Classe/E-Classe 4

402704 Connection set D-Classe 4

14-50


Rain

wat

er

36

IRM®- 25 Rainmanager E-Class

PrincipleThe IRM® controls with micro-processor of the GEP E-Class checks, monitors and controls the entire rainwater system and guarantees continuous high reliability.


Thanks to these two independent water flows, it is possible to keep the rainwater system operational in case of an empty tank or for maintenance works in the large tank. Thus, the hybrid system is always operational, even without the large tank.

The reliability can be increased even further in combination with a GEP overflow trap with an alarm. In case of reverse flow from the sewer, the system will automatically switch to

drinking water and the fault will be indicated optically and acoustically by means of the GEP E-Class.

After a signal from the level indicator, the alarm or the manual switch, the GEP E-Class IRM® system controls automatically switch to drinking water. In this case, (drinking) water is drawn from the break tank. The status and water level can be read from the control panel of the IRM® controls. The controls furthermore provide control of the automatic filter cleaners of the Trident rainwater filters.


GEP E- Class with internal pumpinstallation, breaktank, IRM®- system control in steel housing

Product Advantages

• Double pump system, horizontal centrifugal pumps • Cascade controlled.• Possibility of connecting an additional (second) supply


supply pump)• Electronic controls with four-line LCD-display.• Operation hours counter for every pump.• Pressure indicator for the system.• Level indicator of the water level in the rainwater well.

(optional)• Manual switch to tap water is possible.• Potential-free alarm• RS232 bus connection• Prefab assembly in box made from enamelled steel.• Control of automatic filter cleaners.

Description



• Ready for immediate operation, prefab assembly, including double pump system

Digital LCD-Display

CER TIFICAAT

Max. flow in m3/h 25

Max. pressure in bar 5,8

Voltage 400V/50Hz

Max. power usage A 2 x 6,5 A

Max. Power in kW 2 x 2.680

Technical dataProtection class IP44


Control Voltage 9V DC


Housing metal metal



Price group

Width mm 800





Pressure pipe 1 1⁄2“bi

Drinking water connection 5/4“bu

Supply pump 1 1⁄2“bi


Supply Voltage 400V

Dimensions E-ClassDescription

Accessories

The GEP E-Class is built into a steel box and the integrated break tank is supplemented with water from the large tank by means of a supply pump. In case of an empty tank, the break tank is supplemented with drinking water. The double pump system in the GEP E-Class provides water pressure from the break tank to the tap points. The IRM® system controls of the GEP E-Class provide level indication of the tank, automatic controls of the pumps and automatic drinking water supplementation.

Moreover, the controls have the following protections:checking and setting switch points, system check with acoustic and optic alarm, reverse flow protection, pump motor protection, potential-free contacts, possibility of switch to drinking water manually, checking level sensor

Connections:• Computer Bus RS232


Double pump system with:• Independent commissioning • Manual individual pump test• Dry running protection• Duration protection (if the pump is



• Cascade controls of the pumps• Control of automatic filter cleaners of

Trident rainwater filters• Pressure indicator on LCD Display

LCD-Display



UKArt. No Description PG

402615 IRM - 20 Rainmanager E-Class 20-50 4




Accessories

402709 Supply pumpset E-Class 2 pieces 230V 4

402713 Non-return valve D-Classe/E-Classe 4

402705 Connection set E-Classe 4

E-Class type 20-50 20-60 25-50 25-60

Power (watt) 2x1.500 2x2.200 2x1.500 2x2.200

power consumption (A) 2x3,5 2x5,1 2x3,5 2x5,1

• E-Class supply pump• Reverse flow protection • Non-return valve• Water trap


Rain

wat

er

38

IRM ® Hybrid-A-Class Customization.



• Can connect alarm trap• KIWA certified drinking water

Product Advantages

• Electronic IRM® controls with micro-processor• Integrated internal supplementation in accordance

with EN1717• Drinking water supplementation up to 10 m³/hour

with water hammer absorber• Integrated level indicator for system tank and large

tank• Automatic and manual switch to drinking water use• Automatic water renewal of buffer tank• Electronic control and check of the supply pump

and the magnetic valve• Potential-free output for alarm indicators• Can be connected to alarm trap GEP RSW• Hybrid system tank with smoothing inlet and trap

Principle Hybrid systemFor the IRM®-Hybrid rainwater system, the rainwater is pumped from the large tank to the system tank. From this system tank, a double pump system provides water to the tap points. Drinking water supplementation takes place in the system tank. Thanks to these two water flows, it is possible to keep the rainwater system operational in case of an empty tank or for maintenance. This means the hybrid system can operate continuously.The reliability can be increased even further in combination with a GEP overflow trap with an alarm. In case of reverse flow from the sewer, the system will automatically switch to drinking water and the fault will be indicated optically and acoustically.After a signal from the level indicator, the alarm or the manual switch, the A-Class IRM® system controls automatically switch to drinking water. In this case, water is drawn from the system tank. The operational state, possible faults and the water level are displayed on the control panel. Moreover, the A-Class also has a self-inspection function of the magnetic valve. This valve is automatically engaged on a regular basis so that the mains are not filled with still water for a longer period of time.

Description


Hybrid System AQF

Dimensions Hybrid system AQF 570/690 Liter Grey

1430

/170

0

1170

/144

5

570 liter tank690 liter tank

Art. No Description Dimensions in mm(HxWxL)

Connections Weight PG

402619 Hybrid system AQF 570 Liter Grey 720x720x1430 Top 2 x 2“ Bottom 2 x S56x4 18 kg 4

402620 Hybrid system AQF 690 Liter Grey 720x720x1700 Top 2 x 2“ Bottom 2 x S56x4 22 kg 4

402621 Hybrid system AQF 750 Liter Blue 720x720x1720 Top 2 x 2“ Bottom 1 x S56x4 24 kg 4

402622 Hybrid system AQF 1000 Liter Blue 780x780x2000 Top 2 x 2“ Bottom 1 x S56x4 30 kg 4

90

135

720 Z

Hybrid system AQF 570

• KIWA certified internal supplementation• Also available as break tank• Additional connections available• Various capacities• Fits through standard door• Available in various heights

Product Advantages

Synthetic tank, type AQF, from high-quality recyclable polyethylene (HDPE). Tanks are suitable for the storage of rainwater and drinking water and available as break tank, hybrid tank or rainwater tank. Available in grey or blue depending on the volume.

The 570 and 690 litre versions are grey; the 750 and 1,000 litre versions are blue. Tanks are provided with a 240 mm opening on the top that is fitted with a screw cover. Moreover, the tanks are fitted with two connections on the top of 2” each with a screw cap for installing sensors or level switches. On the bottom, the tanks are fitted with one or two connections with an S56 interior thread. These are delivered from the factory with a cap.

Tanks are fitted with handles to accommodate quick and easy installation and transport. Adapters and complete connection sets by GEP are available for the connections on the bottom, such as a tap valve, pump connections, taps, etc. Additional connections, such as an overflow trap, KIWA certified filler funnels, smoothing inlet, large inspection cover, threaded mounts, etc. are available on request.

Description

Dimensions Hybrid system AQF 1000/750 Liter Blue

/167

0

/118

0/7

50

/nvt

1000 liter tank750 liter tank

Hybrid system AQF 1.000

* Take into account the 35 cm working space above the tanks.


Rain

wat

er

40

Price group

Double pump system DPA RC-5

Product Advantages

• Maintenance-free multi-stage centrifugal pump• Very silent operation and self-priming up to 8 metres

high• Includes micro-processing cascade controls• Alternating operation of pumps• Pressure indication on LCD Display• Integrated protection for every pump• Potential-free output for connecting alarm indicators• Completely preassembled on the base plate• Includes dual pressure pipe with 1 ½” interior• Function inspection per pump• Automatic operation hours distribution• Digital LCD display• Configurable engage and disengage pressures• Configurable lag time• Float connection for dry running protection

Description

• Maintenance-free and fitted with dry running protection

• Proportional distribution operation hours over two pumps

• Configurable pressure• LCD Display


402623 Double pump GEP DPA RC-5 4

Accessories

402701 Double pump connection set 4


UK

Pomptype GEP DPA RC-5

Height mm 500

Width mm 350

Depth mm 500

Suction side 2 x 1“

Pressure side 11⁄2“

Weight kg 38

A1 230V/50Hz 3,3

µF 230V/50Hz 12

P1 (Kw) 2 x 0,8

Dimensions and specifications Pump characteristic

Drinking water

Supply

Overflow

Tank-Connection

Supply pump in the tankPressure

pipePump installation

Connection diagram Hybrid system

RM-5

Suct

ion

lift i

n m

Flow in m3/h


Price group

The educational display allows for visualising the water flows and rainwater system consumption at a glance. For a building, such as a school, this provides quick insight into what happens in the building to save on water and the environment. TFT display indicates the following:

• Consumed water since last rest• Total consumed number of rainwater litres in litres • Total consumed drinking water in litres • Water level in rainwater tank.*

The consumption can be set to zero (reset) to measure from a specific point in time; this makes the display very suited for a school’s lesson plan or to provide insight into the daily, weekly, monthly, etc. consumption.The housing is suited for wall mounting. The design of the image can be designed to the client’s wishes, if requested.

Educational display

Digital educational display for monitoring the various water flows of a rainwater or grey water system.

Display can be assembled away from the system controls, for instance, so that the water flows in a building can be displayed to visitors, employees, students or pupils in a reception or central hall in the building.

The display indicates the rainwater consumption, total water consumption, total drinking water consumption and the water level in the rainwater tank. Display on TFT screens suitable for wall mounting.

Educational display

Voltage 230 V/50Hz nominal capacity 6 m3/h

Connection Rainmanager RS232 reach 11 - 12.000 l/h

Connection Display RS485 Max. Temperature 30 °C

Data cable control box in 2 x 2 x 0,2mm² protected Pulse sensor 1 per liter

Data cable control out 3 x 2 x 0,2mm² protected Length 642 mm

Internal connection DIN rail Height 468 mm

Max. cable length 1.000 meter Depth 78 mm

Technical data Educational display


402714 Educational display IRM-8, -10 and -14** 5

402715 Educational display with water gages 5

402716 Customized Display Design 5

UK


* Only in combination with rainwater tank level sensor. ** Educational display is suitable for combination with GEP Rain Managers B-Class and E-Class and E-Class

Operation

Description


Rain

wat

er

42

GEP Pressure vessel

• several volumes available • reliable• increases efficiency and longevity of

pumping system• easy and fast to install• both horizontal and vertical systems

available• water-carrying parts are protected

against corrosion• pressure is easy to adjust

Product benefits

Description

Art. Nr. Description capacity

in liters

P. Max.in bar

Height H in mm

Diameter Ø in mm

Connection (4)

PG

409251 GEP Pressure vessel 8 liter 8 8 325 195 3/4“ 4

402718 GEP Pressure vessel 24 liter 24 8 420 295 3/4“ 4

402719 GEP Pressure vessel Horizontal 50 liter 50 10 390 635 1“ 4

402720 GEP Pressure vessel Vertical 50 liter 50 10 790 370 1“ 4



402723 GEP Pressure vessel Vertical 300 liter 300 10 1225 650 1 1/4“ 4

402724 GEP Pressure vessel Vertical 500 liter 500 10 1450 750 1 1/4“ 4


GEP Pressure vessel horizontal

GEP Pressure vessel

1. Half-shell. 2. Tie rod. 3. Membrane. 4. Connection. 5. Flange. 6. Weld seam. 7. Contra flange.8. Screws. 9. Valve. 10. Air chamber.

The pressure vessel with exchangeable membrane is a metal vessel which can absorbe and store the potential energy of a pressurized liquid in a rubber back, also known as the membrane. When water is required it is possible to make use of the stored energy of the pressurized liquid into usefull capacity. The air chamber is isolated of the water reservoir by the EPDM-membrane (3), which reduces the risks of water pollution by dust, fumes, smoke, oil, bacteria and odors. The insulation between the walls prevents the risk of corrosion.

GEP Pressure vessel

Fluid pressure vessels with interchangeable membrane for sanitary cold water circuits. EPDM membrane, on request BUTYL membrane. Working at a temperature of -10 °C to 110 °C.


Disconnection point Flow x Amount = Flow

Toilet reservoir 12 mm 0,04 l/s* x = l/s

Washing machine 15 mm 0,16 l/s* x = l/s

Urinoir 15 mm 0,24 l/s* x = l/s

Drukspoelinrichting 1,0 l/s x = l/s

Disconnection tap 15 mm 0,16 l/s* x = l/s

Disconnection tap 20 mm 0,5 l/s x = l/s

Disconnection tap 25 mm 1,0 l/s x = l/s

Total Flow = ∑ = l

Total Flow x Simultaneity factor = Flow Qmax

l/s x = l/s

hd + (ld x 0,2) = Hd

m + m = m

hs + (ls x 0,2) = *Hs

m + m = m

Minimum pressure at disconnection point = 10 m

Max discharge height (*Hmax) = m

Type Qmax Hmax

l/s m

Pump capacity calculation

Project:

Street:

PC + City + Country:

Calculation maximum flow of pump

Physical principles:Water temperature: 11°C Kinematic viscosity: 1,52mm2/s Density: 0,999kg/dm3

Vapure pressure 0,0116bar

* source isso 70.1

The total flow has to be multiplied with a

simultaneity factor when several properties are

connected to a single pump:

Discharge height

Result pump choise

ld hd

lshs

*If Hs is larger than 5m, a submersible pump has to be applied.

Number of houses Simultaneity factor

1 1,0

2 0,9

3 0,8

4 0,7

5 0,6

8 0,5

10 0,4

20 0,35

Suction pipe

Length of suction pipe ls (m)

Suct

ion

heig

ht h

s (m)

Max suction pipe Duplex-Systeem

Max suction pipe Implex-Systeem

Suction length and - height of a centrifugal pump

Length of suction hose between system control and pump ls (m)

Hei

ght o

f tan

k bo

ttom

to th

e bo

ttom

of

the

syst

em c

ontr

ol h

s (m)

ls

hs

hs

ls

Attention!Systems outside of the light shaded area may cause malfunctions.

Suction pipe: PE-HD 1“Flow: 3 m3/h

Suction pipe: PE 1“Flow: 4m3/h

0,9

00 5 15 20 25 30 3610

1,5

2,1

2,7

3,6

4,8

6,0

7,2

8,4

0 5 10 15 20 25 30 35

5

4

3

2

1

0

www.gep-rainwater.com

x 3.600 = m3 /h

w w w . g e p - r a i n w a t e r . c o m

Utilize the possibilities of rainwater

GEP, the rainwater specialist!

© GEP

NL +31 (0)183 610520

BE +32 (0)56/299.701

GEP has a complete, comprehensive and quality range of products which allows composition of each project with an adequate and sustainable water system.

Rainwater

Waste Water

Disconnecting & Infiltration

Drinkingwater

DEHOUST Tanks

Breaktanks

Grey Water

Design your rainwater system onlineusing the calculation module on www.regenwater.com

GEP-Matrix® Boxesfor infiltration

Flatrainwater

tanks

Rainwater filters

(Rain)water pumps

Submersible pumps

Bladder tanks

Rainwater tanks with integrated

rainwater filter

Waste water pumpsand pump pits

Date post:	12-Aug-2019
Category:	Documents
Upload:	tranquynh
View:	220 times
Download:	0 times

IRM Control Systems - cdn.gep-water.comcdn.gep-water.com/GEP-download/en_GB/10.GEP Brochures/GEP...

Documents