IRMWARE VERSION 071619 SET UP AND OPERATION · 2020-04-10 · POINT CTRL VIRTUAL REALITY CONTROL...

Spec Tech

Design Manufacturing and Training

FIRMWARE VERSION 071619

SET UP AND OPERATION

1

2

Table of Contents

Firmware Updates

Overview

HMS & FCU Controls

Charging FCU’s

FCU LED Time Out

FCU Brightness

Mouse Wheel Emulation

Mounting HMS

IR Room Survey

Calibration Overview

V/R View User Menu

Initial Calibration

Edge Calibration

FCU Zoom

DCU Button Mapping

Calibration Practice Page

3

4

7

10

11

12

13

14

15

16

18

19

23

27

28

29

3

Firmware Updates

V071619 DCS Centered Windowed View is now default. Added cursor box limits to calibration procedure to prevent clicking out of DCS window.

Factory reset is now for Rift S, DCS centered windowed view, FCU Proximity Zoom = OFF, Left Mouse Button = FCU Button 1 (Forward Most Button)Improved FCU button zoom – FCU buttons 1 and 2 must be pressed simultaneously within ½ second to activate zoom. This reduces unintended zooming.

V070419Zoom Function – Enhanced Zoom functionality and added ability to turn off proximity zoom.

POINT CTRLVIRTUAL REALITY CONTROL DEVICE SPEC TECH DESIGN MANUFACTURING AND TRAINING

HOW DOES POINT CTRL WORK

Point CTRL employs 3 wearable devices working in unison. The HMS sensor is mounted to the

Virtual Reality headset and tracks the position of each IR LED mounted to the FCU’s. The

location of the on-screen cursor in the virtual reality environment corresponds to where the user

is physically pointing in real life. Switches and dials are then manipulated by pressing the

function specific tactile switches on each FCU.

Prototype HMS and FCU

4


WHAT TECH DOES POINT CTRL USE

Point CTRL uses 3 wirelessly connected devices utilizing the newest IR optical tracking, and RF

transceiver technology.

FCU or the Finger Control Units consist of an Atmel MCU, 2.4GHZ transceiver, 850nm LED, three

tactile pushbuttons, and an 150mah onboard rechargeable lithium polymer battery.

HMS or the Head Mounted Sensor consist of a PixArt proprietary optical tracking sensor, 2/4GHZ

transceiver, Atmel MCU, two setup control buttons , and USB micro USB interface.

Point CTRL is recognized as a windows HID compliant pointing device, and requires no driver

installation. Point CTRL is compatible with any simulator, or software title that has mouse support.

5


COMPONETS

HMS ( Head Mounted Sensor)

FCU (Finger Control Unit)

3Meter Micro USB Cable

Lipo Battery Charger

Lipo Safe Bag

Attachment Accesories

6


HMS (HEAD MOUNTED SENSOR)

IR Sensor

BTN Right

Hold to Enter

User Settings

and

Calibration

Factory Reset

The HMS can be reset to

factory settings. Press and

hold both of the black

buttons on the HMS while

pressing and releasing the

white reset button. After

successful reset the cursor will

move from the left edge of

the field of view to the right

edge as confirmation.

Factory Calibration is for Rift S

, Full Screen, Stretched view,

but it will serv as a good

starting reference for all other

V/R Headsets.

HMS Reset

Double Press

for Firmware

Update

Micro USB

Connector

Auxiliary V/R HMD

Push-Button

Headers

BTN Left

Disables FCU

7


FCU (FINGER CONTROL UNIT)

IR LED

Charging

Jack

ON/OFF

Strap

Adjustment

Slots

Elastic

Strap

FCU Button 3

Mouse Wheel

FCU Button 2

Right Mouse BTN

FCU Button 1

Left Mouse BTN8


FCU OPERATION – POWER ON/OFF

TURN ON TURN OFF

IR LED

Press and

Hold for

1Second

Until IRLED

Lights

IR LED

Press and

Hold for 3

Seconds

Until IRLED

Turns Off

Must wait 4 seconds after

turning FCU OFF before

turning FCU back ON again

Must wait 4 seconds after

turning FCU ON before

turning FCU back OFF again

9


FCU CHARGING AND LIPO BATTERY SAFTEY

Intelligent ChargerNormal Charging time is between 15

and 40 minutes

Charging

Jack

Charging IndicatorRed Light On = Battery Fully Charged

or No Battery ConnectedLight Off = Battery is Charging

LiPo Safe

Charging Bag

10

LiPo Battery SafetyCare must be taken when

using Lithium polymer

batteries. A faulty charger or

battery could cause heat

and flames. Always store

and charge your FCU’s in

the provided fire-resistant

case. Never leave Lipo

batteries unattended during

quick charging.

Graphic Place Holder


FCU OPERATION - LED TIME OUT

ENTER SET-UP MODE COUNT FLASHES

IR LED

Step (2)Press and Hold for

1 SecondIRLED will rapidly flash

for 1 second

confirming you are in LED Timeout mode

Step (3)IR LED Flashes

Once per second

Step (4)As soon as the desired time out is reached press FCU BTN 3 to save

Step(1) Press and Hold FCU BTN 1

before and while turning on FCU

Each Flash represents 10 seconds of LED TimeoutExample 4 flashes = 40

seconds of inactivity before the LED turns off.The LED is turned on by

pressing any of the three buttons

LED will flash rapidly and then turn off

confirming LED Time

Out is set. Press any BTN to turn on LED

11


FCU OPERATION - LED BRIGHTNESS ADJUSTMENT

ENTER SET-UP MODE SET BRIGHTNESS

IR LED

Step (2)Press and Hold for

1SecondIRLED will Slowly din and then get bright

again confirming you are in LED Brightness Adjustment Mode

Step (3)IR LED will display currently

set brightness

Step

(3A)Press to Brighten

LED

Step(1) Press and Hold FCU BTN 2

before and while turning on FCU

LED Brightness can be dimmed to save battery

life but is does slightly affect tracking resolution

Step

(3B)Press to Dim LED

Step (4)Press to

Save Brightness

setting

12


FCU OPERATION – MOUSE WHEEL FUNCTION

Press to Execute Mouse

Wheel Movement

Press to Set Mouse

Wheel Direction

Mode to Forward

Mouse Wheel Functionality Emulation Direction

The Mouse Wheel Button (3) will Emulate the Mouse

Movement Direction of the Last Pressed BTN (1 or 2)

Press to Set mouse

Wheel Direction

Mode to Backward

BTN 1BTN 2

Emulation Speed

The Mouse Wheel Speed will Start out Slowly and

Increase in Speed if the Execute BTN (3) is Held downBTN 3

Note:

When Changing Mouse Wheel

Direction with BTNs (1 or 2) be

sure to not click on switches or

dials

13


HMS OPERATION – MOUNTING TO VR HEAD SET

Pre-PositionCenter sensor and ensure it is parallel to your line of sight

before making contact with tape

Cut and Fit DS Tape Cut

and fit double sided tape

to HMS

Mount SensorFirmly Attach

Sensor and secure micro USB cable

with zip ties

14

Test Fit Generic MountIdentify Gaps to be filled with double

face tape or EVA foam if required

Dedicated

MountModel Specific

Dedicated Mounts require

no fitting. Example Rift S


HMS OPERATION – SURVEYING IR ENVIRONMENT / FCU TEST

Check Sensor FOVCheck Sensor Field of View By Moving FCU

to Confirm Limits

HMS On indicator

Red Glow = ON

Survey

RoomRotate Sensor

While Seated in Flying Position to Check for Stray IR Light

Occlude Any

Detected IR Sources

IR and USB indicatorGreen = IR Source DetectedAlso Flashes when Sending

HID DATA

14

1 F

OV

141 F

OV

BADPhoto Courtesy

mariner3302

FCU In FOVGreen Glow =

FCU Visible

FCU Out Of FOVNo Green Glow =

FCU Not Visible

15


CALIBRATION OVERVIEW DCS WINDOWED VIEW

Windowed View Cursor BoxPointCTRL is optimized for DCS windowed view, compared to full screen

stretched view. A user defined cursor box limits the mouse movement to

the DCS window. Your HMD screens limits must be defined to ensure that

we don’t click outside of the DCS window causing it to lose focus. We

start with defining the horizontal 1& 2, followed by the vertical 3 & 4.

4

3

2

4

3

2

1

1

16

Windowed View

Cursor Box DefinitionThe Cursor box limits will appear as 4 flashing cursors each axis. The

horizontal axis will be displayed and adjusted first by cursor sets 1 & 2,

followed by display and adjustment to cursor sets 3 & 4.

3

21

4


CALIBRATION OVERVIEW

Define the Left and Right Visible Cursor Limits of Your V/R Head Set

Each V/R Head has different resolutions and field of view. We must first define the Left and Right cursor

limits in V/R using the FCUs.

1

Calibrate FCU to Each Defined LimitNext we point at and click each of the 5 sequentially presented cursor targets.

After the last Target, PointCTRL is operational and the settings are saved.

Note: You will only see the stationary cursor targets, not any moving cursors.

1 32

4

This page is only an overview, detailed instructions follow.

17

Define the Upper and Lower Visible Cursor Limits of Your V/R Head Set

This step is not usually required. It is only necessary for desktops that are extended vertically by multiple

monitors or a V/R Headset reporting as two monitors.

5

Cursor Movement Menu Representations

Down/UpEnter or

Exit Setting

FOV Define

Left/Right

Upper/Lower

Center

ZoomDefine FCU

to HMS

Distance

Edge CalibrationFine Adjustment

of Finger to

Cursor Edge

Movement

FCU MapingDefine Left &

Right Mouse

Buttons

ExitExits

Graphic

Menu

Menu LeftDisplays Next

Graphic Menu Item

Menu RightDisplays Next

Graphic Menu Item

Select Menu Item

Advance StepSteps from Left/Right

to Upper/Lower Limits,

Then, Cursor Targets

Enter User MenuPress and Hold Right Button on HMS for 3

seconds until the Cursor moves down

the center of the screen.

18

Toggles HMS ON/OFF

POINT CTRLVIRTUAL REALITY CONTROL DEVICE

CALIBRATION (MONITOR VIEW) SET CURSOR BOX LIMITS

Step1Confirm Use Mouse

Checkbox is Checked in the DCS VR Setting Tab

Step 3Navigate to the Calibration Mode (cursor tracing a circle)and Press FCU Button 3

Note: You may have to manually activate your HMD’s presence sensor with a Finger or Blue packing tape to activate your desktop view.

Step 44 Flashing Cursors will be displayed, Move the

Cursors with the FCU Buttons (shown below)positioning them at the Left and Right

Edges inside the DCS Window as Shown Below.

Monitor View

Menu Left

Displays Next

Graphic Menu Item

Menu Right

Displays Next

Graphic Menu Item

Select

Enters the Menu

Setting Item

T1 = Move Cursors Left

T2 = Move Cursors Closer

T1 = Move Cursors Right

T2 = Move Cursors Wider

Toggles Between

T1 and T2

Step 2With your VR Head Set

Off Your Head and Viewing your Monitor,

from the CockpitEnter User Settings Menu

Press and Hold BTN2 (Right) for 3 Seconds

19

HMS ON/OFF

Toggle

Step 5Press the

ON/OFF

Button to

Advance to

the Vertical

Cursor Box

Adjustment

Monitor View

CALIBRATION (MONITOR VIEW) SET CURSOR BOX LIMITS

20

Note:Step 6 is usually not

required, and you can bypass it by pressing the

ON/OFF button

Vertical Cursor Box Limits different from factory

reset is only required for an expanded vertical

desktop .

Cursors can not be moved up or down

following a factory reset, or while at normal max

height setting. They must be made narrower first.

Monitor View

Step 64 Flashing Cursors will just be visible at the top and bottom of the monitor. If required. Move the Cursors with the FCU

Buttons (shown below)Positioning them at the Top and Bottom Edges inside the DCS Window as Shown Below.

T1 = Move Cursors Down

T2 = Move Cursors CloserStep 7

Press the ON/OFF

Button to

Advance to the

Setting the Cursor

Edge Targets

Toggles Between

T1 and T2

T1 = Move Cursors Up


Step 8Put on your VR Headset to

proceed.

Coming Soon

You can also continue with the

custom DCS kneeboard instructions

in the mission PointCTRL_Set_Up.miz

available from the PointCTRL.com


CALIBRATION (V/R HEAD SET VIEW) SET CURSOR TARGETS

Step 9Two Cursor Targets will be Displayed. Use the

FCU Buttons to Position the Two Cursors as Shown

V/R Head Set View

T1 = Move Cursors Left


T1 = Move Cursors Right


Toggles Between

T1 and T2

Step 10Press the

ON/OFF

Button to

Advance to

the Vertical

FOV

Adjustment

Step 11Two Cursor Targets will be Displayed. Use the

FCU Buttons to Position the Two Cursors as Shown

T1 = Move Cursors Down


T1 = Move Cursors Up


Toggles Between

T1 and T2

Note:

Step 11 is usually not required,

and you can bypass it by

pressing the ON/OFF button

Setting the vertical cursor

targets different from factory

reset is only required for an

expanded vertical desktop.

Cursors can not be moved up

or down following a factory

reset, or while at normal max

height setting. They must be

made narrower first.

Step 12Press the ON/OFF

Button to

Advance to the

Cursor Target

Presentations

CALIBRATION (V/R HEAD SET VIEW) ALIGN AND LOCK IN TARGETS

Step 13Take your time and accurately point at, and accept each of the 5 sequentially presented targets. You will not see a moving cursor. The objective is to be naturally pointing at each

target when pressing the FCU accept button.

Press FCU Button 1 to

Accept in Cursor

Alignment

12

5

4

3

Important !!Before Accepting Cursor Alignment

Press the FCU Button 3 to

Ensure the LED is On and not Timed

Out

22

Edge Calibration

PointCTRL is now ready to use. After you become more familiar with the operation and functions, you can apply edge calibration to

fine tune the cursor movement. Edge Calibration helps keep the cursor locked to the same position in the cockpit when the

head is moved but not the FCU.

Confirm Calibration

After clicking on the final target PointCTRL will exit the Calibration Menu and save your

settings. Point to different Items in the cockpit and verify that the cursor is where you are

pointing. If not, you can recalibrate.


EDGE CALIBRATIONEdge Calibration is just what the name implies. We are

only adjusting the Finger to Cursor alignment at the

edges of our view without effecting the center

alignment.

The left and right Finger to Cursor Alignment is done in

one step because of the symmetrical bio-mechanics

between the FCU finger and the HMS.

(left and right edge movement is mirrored)

The upper and lower edges are adjusted separately

because of the asymmetric biomechanics of raising and

lowering the arms in relation to the FCU finger and the

HMS.

(up and down movement is not the same)

When properly executed, edge calibration will enable

the cursor to stay in the same location in the cockpit

when the head is slowly moved left, right, up, or down,

while the finger or FCU is stationary.

Note: While PointCTRL processes and sends mouse

commands at 200 FPS there is a short lag in V/R when

the head is moved quickly . This is followed by the

cursors quickly settling back down to its intended

position. (Looking into WMR implementation for solution)

Step 2Navigate to the Edge Calibration Mode

(4 Cursor Starburst)and Press FCU Button 3

V/R Head Set View

Menu Left

Displays Next

Graphic Menu Item

Menu Right

Displays Next

Graphic Menu Item

Select

Enters the Menu

Setting Item

Step 1Enter User Settings Menu

While in Cockpit ViewPress and Hold BTN2 (Right) for 3 seconds

23

HMS ON/OFF

Toggle

Do not press


EDGE CALIBRATION LEFT AND RIGHT EDGE

Step 3Select a point in the cockpit where you will be manipulating most of your controls and center

it in your field of view and point at it. Finger and Cursor should line up

Step 4While keeping your hand in the same location,

move your head slowly left or right until the cursor reaches the edge of your view. Observe

if the cursor has moved left or right from its original location.

Move Cursor Left

Move Cursor Right

Advance to Next Step

Upper Edge Cursor Alignment24

Step 5Keeping your head and hand in the

same stationary position, adjust the lateral cursor location with the FCU buttons until it returns to its original

location centered on the MFD . Press FCU button 3 when done.

If cursor moved here

as head was rotated…

…with out moving you head or

hand ,move cursor back here

by pressing FCU Button 2

Center MFD in FOV

and Point at it


EDGE CALIBRATION UPPER EDGE CURSOR

Step 6Return to your reference point in the cockpit

and center it in your field. Now point directly at the reference point again.

Finger and Cursor should line up

Step 7While keeping your hand in the same location, move your head slowly down until the cursor

reaches it movement limit. Observe if the cursor moves Above or Below original location.

Move Upper Cursor Up

Move Upper Cursor Down

Advance to Next Step

Lower Cursor Edge Alignment25

Step 8While keeping your head and hand in

the same stationary position, adjust the cursor location with the FCU

buttons until it returns to its original location centered on the MFD.Press FCU button 3 when done.

If cursor moved here as

head was rotated down…




Center MFD in FOV

and Point at it

Note:

During this phase you can

only adjust the cursors upper

limit. The FCU buttons will

only move the cursor when

the cursor is located on the

upper half of the screen.


EDGE CALIBRATION LOWER EDGE CURSOR

Step 9Return to your reference point in the cockpit

and center it in your field. Now point directly at the reference point.

Finger and Cursor should line up

Step 10While keeping your hand in the same location, move your head slowly upward until the cursor

reaches it limit. Observe if the cursor moved Above or Below original location.

Move Upper Cursor Up

Move Upper Cursor Down

Advance to Save Settings

26

Note1:

During this phase you can

only adjust the cursors lower

limit. The FCU buttons will

only move the cursor when

the cursor is located on the

lower half of the screen.

Step 11While keeping your head and hand in

the same stationary position, adjust the cursor location with the FCU

buttons until it returns to its original location centered on the MFD.

Press FCU button 3 to save and Exit.

If cursor moved here when

you looked down…




Center MFD in FOV

and Point at it

Note 2:

Care must be take to

remember wich of the 3

cursor adjustment you are

making, 1) Left/Rigtht,

2)Upper, or 3) Lower.

USER SETTINGS FCU ZOOM

Step 2Navigate to the Zoom Mode (cursor tracing a

rectangle)and Press FCU Button 3

Step 3Two cursors , a center for reference, and the active, will

become visible. Move FCU to where you want the

Zoom to become active and Press FCU Button 2.

To Disable Proximity Zoom move the FCU close to HMS

while keeping the active cursor centered., When the

second cursor disappears Press FCU Button 2

V/R Head Set View

Menu Left

Displays Next

Graphic Menu Item

Menu Right

Displays Next

Graphic Menu Item

Select

Enters the Menu

Setting Item

Set Zoom Out Distance

Set Zoom In Distance

Save Setting and Exit


While in Cockpit View

Press and Hold BTN2 (Right)

for 3 seconds

27

Step 4Move FCU to the distance where you want the Zoom

to Return to normal and FCU Button 1

Step 5Continue to test and modify you distance settings.

When satisfied Press FCU Button 3 to Save and Exit

2 & 3 Together

Zoom Out

1 & 2 Together

Zoom In

IRLED Not in

FOV Zoom Out

NoteIf Proximity Zoom is disabled, you will see the cursor

move from left to right before moving up when you

save the settings

ImportantIn DCS, you must first bind

the VR zoom to [RightALT]+[0]

[0] = Keyboard Zero, Not Pad

USER SETTINGS FCU MAPPING

Step 2Navigate to the FCU Mapping Mode

(3 Flashing Cursors Representing FCU Buttons)

and Press FCU Button 3

Step 3Cursors will Change to 2 Flashing Cursors Representing

the 2 choices for Mapping. Press either FCU 1 or 2 to

Map the Left Click to. The Other Unpressed Button will

be mapped to Right Click. V/R Head Set View

Menu Left

Displays Next

Graphic Menu Item

Menu Right

Displays Next

Graphic Menu Item

Select

Enters the Menu

Setting Item

Set FCU Button 1 to

Left Click

Set FCU Button 2 to

Left Click

Save Setting and Exit


While in Cockpit View

Press and Hold BTN2 (Right)

for 3 seconds

28

Step 4Press FCU Button 3 to Save Remapped Settings

Mapping will only Change the Left and Right Mouse

Click Functions

29


Spec Tech

Design Manufacturing and Training

30

31

PointCTRL Sensor Field of View

VR Headset Image Field of View

Long armed Person

pointing at cursor

Short Armed Person

pointing at cursor

Cursor 45 degrees

right of center view

Cursor 45 degrees

left of center view

HMS sensor reading 60

degrees left of center

HMS sensor reading 50

degrees right of center

The reason we do not see a moving cursor while clicking on the cursor

target is because we want to point at the cursor targets naturally and

intuitively. This method aligns the cursors to our perception and feel of

where we are pointing in the 3d environment.

Date post:	12-May-2020
Category:	Documents
Upload:	others
View:	3 times
Download:	0 times

IRMWARE VERSION 071619 SET UP AND OPERATION · 2020-04-10 · POINT CTRL VIRTUAL REALITY CONTROL...

Documents