Ironing board design and construction - Home | Interact personal... · Web viewThe ironing board...

Jansan FSSI Personal Hygiene & Paper IPD’s

NSN: 3510-00-222-1457

PIN, NET, LAUNDRY: Shall be in accordance with Commercial Item Description (CID) A-A-52127 dated June 15, 1993 and 27 September 2001 Validation Notice 1 dated with the following characteristics;

Length overall - 5 inches (plus or minus 1/8 inch)

Material; Clasp - copper alloy Wire - copper alloy

Finish - nickel or chromium

NOTICE: The use of any plastic material in the packaging or packing of this item is prohibited.

EXCEPTION TO THE CID:

1) Delete paragraph 3.1 and substitute the following: 3.1 Product Conformance. The products provided shall meet the salient characteristics of this commercial item description, conform to the producer’s own drawings, specifications, standards, and quality assurance practices and be the same product offered for sale in the commercial market. The Government reserves the right to require proof of such conformance.”

Unit of Issue - HD (one hundred pins).

NSN: 3510-00-273-9738

NET, LAUNDRY: Shall be in accordance with Federal Specification JJ-N-180G dated July 20, 1978 with the following characteristics;

Type I - With grommetsStyle A - Leno weave (Nylon) or Style B - Warp knit (Nylon)Size 2 - 12 x 22 inches (305 x 559 mm)

EXCEPTIONS TO THE SPECIFICATION:

1) Style B warp knit (Nylon) may be provided in lieu of Leno weave (Nylon).

2) Polyester may be used in lieu of nylon. When polyester is used, the bursting strength requirements of Table I shall be amended to require 150 pounds, for nets manufactured from polyester.

3) Add the following sentence to Paragraph 3.2.3: “Dimensions are to the center of the hole in the grommet.”

4) Delete all references to “MIL-STD-105” and substitute; “ANSI/ASQC Z1.4”.

Application for copies of ANSI/ASQC standards should be addressed to American Society for Quality Control, PO Box 3005,611 E. Wisconsin Avenue, Milwaukee, WI 53201-4606.

Unit of issue is 1 DZ (12 each)

NSN: 3510-00-273-9739

NET, LAUNDRY: Shall be in accordance with Federal Specification JJ-N-180G dated July 20, 1978 with the following characteristics;

Type I - With grommetsStyle A - Leno weave (Nylon) or Style B - Warp knit (Nylon)Size 4 - 24 x 36 inches (610 x 914 mm)

EXCEPTIONS TO THE SPECIFICATION:

1) Style B warp knit (Nylon) may be provided in lieu of Leno weave (Nylon).

2) Polyester may be used in lieu of nylon. When polyester is used, the bursting strength requirements of Table I shall be amended to require 150 pounds, for nets manufactured from polyester.

3) Add the following sentence to Paragraph 3.2.3: “Dimensions are to the center of the hole in the grommet.”

4) Delete all references to “MIL-STD-105” and substitute; “ANSI/ASQC Z1.4”.

Application for copies of ANSI/ASQC standards should be addressed to American Society for Quality Control, PO Box 3005, 611 E. Wisconsin Avenue, Milwaukee, WI 53201-4606.

Unit of issue is 1 DZ (12 each)

NSN: 4510-00-203-2707

DISPENSER, SOAP, LIQUID: Shall be a rigid dispenser suitable for dispensing liquid soap, and with the following characteristics:

1) The dispenser shall have a 10 fluid ounce minimum capacity and shall dispense liquid soap by means of a spring action push-in valve or other suitable pump action design. The dispensing mechanism shall be capable of being operated with one hand while dispensing soap. The dispenser shall be self-priming and except for initial use after filling or refilling, shall not require more than one positive action to begin dispensing soap.

2) Parts in contact with soap shall be stainless steel, chromium plated brass, chromium plated carbon steel, chromium plated aluminum, chromium plated zinc die casting, or plastic.

3) All exposed or visible metal parts except stainless steel shall be chromium plated. Stainless steel shall have a polished finish. Exposed or visible plastic shall be chromium plated, white plastic, white baked on enamel finish, or the manufacturer’s standard pastel color.

4) A wall type bracket or holder with not less than three mounting screws shall be furnished with each dispenser. The dispenser shall be fully assembled and ready for mounting on a flat vertical surface. Installation, operation, and maintenance instructions shall be provided with each dispenser. The instructions shall include repair procedures and a listing of available repair parts.

5) The dispenser’s capacity shall accept liquid type soap through a separate bulk source and capable of being cleaned, filled, and repaired without the use of special tools.

Unit of issue is each (EA)

NSN: 4510-00-224-8549

DISPENSER, PAPER TOWEL: The dispenser shall be designed for and capable of dispensing single-fold paper towels (for hand drying), and shall have the following characteristics:

1) Fabricated of carbon or stainless steel with a minimum thickness of 0.029 inch.

2) Minimum capacity of 350 paper towels. The paper towels shall have a basis weight in pounds of 25-30 (24x36-500), smaller dimension of 9-1/4 inches 1/2 inch, and a fold depth of 5-1/2 inches 1/2 inch.

3) Provided with a front opening hinged door panel and lock with one key, minimum, and shall lock automatically when the door is closed, or be provided with a dead bolt keylock, at the manufacturer’s option; bottom dispensing slot; fill indicator; and rear panel fastening holes for surface mounting.

4) The paint for the finish shall be white dry/powdered or a smooth baked, white gloss enamel, which shall be hard and durable. The exterior and interior finish shall be continuous, free from blisters, pinholes, or other blemishes. Exposed surfaces of the finish shall be smooth and uniform in application and color, free of chips, runs, cracks, or other defects affecting appearance or serviceability.

Unit of issue is each (EA)

NSN: 4510-00-752-9065

DISPENSER, TOILET PAPER: 3-roll toilet paper dispenser shall be designed for surface mounting vertically, is intended for other than residential use, and shall have the following characteristics:

1) The cabinet shall be stainless steel with a satin finish. At the manufacturer’s option, the front panel may be gray plastic with a textured or embossed finish. All other exterior surfaces must be metal. At the manufacturer’s option, interior metallic surfaces shall be chromium plated, bright zinc plated, dry/powdered or baked on white enamel. Interior plastic surfaces shall be as molded.

2) The cabinet closure panel shall lock automatically upon closing or shall be provided with a tumbler lock and key, all keyed alike.

3) The cabinet opening shall be a minimum of 4-5/8 inches in width, height, and depth, for acceptance of 2-ply toilet paper rolls, 4-1/2 + 1/8 inches wide x 4-1/2 + 1/8 inches in diameter with a 1-3/8 to 1-3/4 inch inside diameter core.

4) The dispensers shall be provided with fastener holes or slots at the corners with adequate spacing across the cabinet back to provide for stability after installation. Each cabinet shall be furnished with plated or stainless steel fasteners, sheet metal screws, or mounting hardware normally supplied with the manufacturer’s standard commercial product.

5) The cabinet shall be capable of housing three (3) rolls of toilet tissue mounted horizontally and stacked vertically. The dispenser roller mechanism shall be capable of automatically dropping the stored roll(s) of tissue, without jamming, when the roll being dispensed has 5 percent or less remaining.

6) Each dispenser shall be clearly and permanently marked with the manufacturer’s name or trademark.

Unit of Issue – EA (Each)

NSN: 4510-01-521-9867

DISPENSER, SOAP: Shall be Travis Association for the Blind Skilcraft p/n 1959-12, GOJO Industries, Inc., p/n 9033-12, or equal, in accordance with the following characteristics:

One-hand push operation and portion control wall soap dispenser shall be compatible for use with GOJO 800-mL Lotion Soap and Shampoo refill pouches, including GOJO Lotion Soap p/n 9112-12 (8520-01-378-3090) and GOJO Shampoo p/n 9126-12 (8520-01-522-0836).

Unit of Issue – BX (box containing twelve (12) dispensers)

NSN: 4510-01-521-9868

DISPENSER, SOAP: Shall be Travis Association for the Blind Skilcraft p/n 1959-01, or equal, in accordance with the following characteristics:

One-hand push operation and portion control wall soap dispenser shall be compatible for use with GOJO 800-mL Lotion Soap and Shampoo refill pouches, including GOJO Lotion Soap p/n 9112-12 (8520-01-378-3090) and GOJO Shampoo p/n 9126-12 (8520-01-522-0836).


NSN: 4510-01-521-9870

DISPENSER, HAND SANITIZER: Shall be Travis Association for the Blind Skilcraft p/n 1973-06, GOJO Industries, Inc., p/n 2120-06, or equal, in accordance with the following characteristics:

One-hand push operation and portion control wall hand sanitizer dispenser shall be compatible for use with GOJO 1000-mL hand sanitizer refill pouches, including GOJO Purell Instant Hand Sanitizer with Aloe 2137-08 (8520-01-522-3888), GOJO Purell Instant Hand Sanitizer 2156-08 (8520-01-522-0828 and GOJO Purell Instant Hand Sanitizer 2156-04 (8520-01-539-0840).

Unit of Issue – BX (Box containing six dispensers)

NSN: 4510-01-521-9873


One-hand push operation and portion control wall soap dispenser shall be compatible for use with GOJO 2000-mL lotion soap and shampoo refill pouches, including GOJO Body and Hair Shampoo 2252-04 (8520-01-522-0832) and GOJO Lotion Soap with Moisturizers 2217-04 (8520-01-522-0837).

Unit of Issue – BX (Box containing eight dispensers)

NSN: 4510-01-551-2864


One-hand push operation and portion control wall foaming soap dispenser shall be compatible for use with GOJO 1250-mL foam soap refills, including GOJO Luxury Foam Antibacterial Handwash p/n 5162-03 (8520-01-556-2576) and GOJO Green Certified Foam Hand Cleaner p/n 5165-03 (8520-01-556-2577).

Unit of Issue – BX (Box containing six (6) dispensers)

NSN: 6508-01-579-3825

HAND SANITIZER GEL: Shall be in accordance with the following characteristics:

Hand sanitizer gel in a 2-liter pump bottle, active ingredient 62% ethyl alcohol (minimum). May be used without water or towels.

Shall meet FDA requirements.

The hand sanitizer gel shall have a minimum biobased content of 73%. The minimum biobased content requirement shall be based on the amount of qualifying biobased carbon in the product as a percent of the weight (mass) of the total organic carbon in the finished product as specified in 7 CFR 3201.18.

Shelf life code: Q Maximum age on delivery - Five (5) months from date of manufacture. Date of expiration shall be thirty-six (36) months from date of manufacture

Unit of Issue – BX (Box of Four 2-liter pump bottles)

NSN: 7240-00-269-1243

BASKET, FRAME MOUNTED: This is a caster mounted steel frame with removable cloth liner (without handles), similar to illustration(s) herein, furnished completely assembled with the following characteristics:

Frame size – Inside dimensions at the top 42”L x 30”W x 30”D

Bottom dimensions shall measure 2-1/2 inches less in length (L) and width (W) than at the top

Casters - Four (4) casters shall be of the same wheel diameterTwo (2) rigid casters shall be mounted on each side and two (2) swivel casters shall be center mounted on each end

Cloth liner – Cotton duck material in natural colorCapacity - 18 bushel

UNIT OF ISSUE - EA (each)

NSN: 7290-00-125-9069

HANGER, COAT: Shall be in accordance with the following characteristics:

Construction. The hanger shall be constructed of steel and shall be designed for standard (light duty) use as a coat hanger. The hanger shall be of a one-piece formed design, with a shoulder bar unit, trouser bar, and suspension hook. The hanger shall be manufactured from steel wire having a minimum diameter of 0.092-inch (Standard Wire Gauge 13 gauge). The hanger shall be swaged (wrapped) around the base of the suspension hook with the option of forming an open eyehook. The hook radius shall completely fit over a 1-1/2 inch (3.81 cm) diameter bar without binding. The trouser rod shall be included without a trouser guard.

Finish. Enamel.

Size. The hanger shall have a minimum width of 15-3/4 inches (40.0 cm).

Workmanship. Hangers shall be free from any sharp edges, projections, and other defects that could snag or tear garments. Surfaces shall be free from flaws, cracked or peeling paint, and other defects that could impair appearance or serviceability as specified herein.

Unit of Issue – BX (Box of 500 hangers)

NSN: 7290-00-148-7068

FLATIRON, ELECTRIC (STEAM): Shall be in accordance with the following characteristics:

Design - Spray, steam, Dry, 120 volts AC, steam vents, water level window.Cord - 2 conductor cord with 2 prong plug.Features - Fabric guide indicator, temperature selector, heel rest. AUTO SHUTOFF FEATURE REQUIRED

Safety - Shall be in compliance with the latest revision of UL 1005

Shall have a button nook or some other feature such as large gap between the sole plate and main body of the flatiron, to facilitate ironing around a button.

CARE AND USE INSTRUCTION BOOKLET: Each flatiron shall be accompanied by a care and use instruction booklet. The care and use instructions shall be in the same format as and contain the same information as the care and use information furnished with the flatiron for commercial sales.


NSN: 7290-00-663-7300

IRONING BOARD, HOUSEHOLD: Household ironing board with pad and Teflon treated or silicone-aluminum coated cotton cover shall be in accordance with the following characteristics:

Ironing board design and construction

The ironing board shall provide a stable, smooth, ventilated ironing surface.

The ironing board shall be made of commercial grade; cold rolled steel and shall have a baked enamel finish or an electrostatic powder coated finish, at the manufacturer's option.

The ironing board shall have a T-leg or four-leg design, at the option of the manufacturer, and shall have a non-mar, non-skid cushioning cap over the end of each leg.

The ironing board shall have a means of opening, closing, and locking to a selected ironing surface height. The ironing board surface height shall be adjustable to any height ranging from 24 ± 1 inch (61.0 ± 2.5 cm) up to 36 ± 1 inch (91.4 ± 2.5 cm), measured from the top surface of the ironing board to the floor. A positive retention feature shall maintain the selected ironing surface height and prevent the ironing board from collapsing.

The ironing board shall fold flat for storage.

The ironing surface shall have a perforated or expanded mesh design, at the manufacturer's option.

The ironing surface shall have the shape and dimensions shown in the figure. The corners at the wide end shall be slightly rounded.

(81.3 ±3.8 cm)

(36.

8 ±1

.3 c

m)

(137.2 ±2.5 cm)

32 ±1.5 inches

54 ±1 inches

14.5

±0.

5 in

ches

Top View

Ironing board performance

The ironing board shall be rigid, stable, free of wobble, and capable of supporting a 50 lb (22.7 kg) weight placed in the center of the board within a bearing area of not more than 64 in2 (412.9 cm2) for three minutes. The ironing board shall be capable of supporting the specified weight without a permanent deflection in the top surface and shall maintain all height positions.

Ironing board pad

The ironing board pad shall fit the ironing board depicted in the figure, covering the entire ironing surface of the ironing board.

The pad shall be cut in one piece, although a separate nosepiece, wide enough to securely hold the end of the pad to the end of the ironing board, shall be sewn to the tapered end of the pad.

The pad shall be an assembly of a top and a bottom layer of interlocked synthetic and natural fibers with a natural or synthetic foam rubber core or shall be a combination of interlocked synthetic and natural fibers without a core. The pad shall be 1/4 inch (0.6 cm) thick, minimum, and shall weigh 14 oz/yd2 (466.7 g/m2), minimum.

At the manufacturer's option, the pad may have a natural or synthetic foam rubber backing.

The entire perimeter of the pad shall be finished with binding tape or over-edge stitching. The edge finish shall be sewn through all component layers of the pad.

Ironing board cover

The ironing board cover shall fit the ironing board depicted in the figure and shall be large enough to be securely fitted over the ironing board top with the pad in place.

The cover shall be unbleached, sized or unsized, 100 percent cotton sheeting or drill.

The cover shall be cut in one piece. A separate nosepiece may be attached at the tapered end of the cover, at the manufacturer's option.

The edges of the cover shall be finished with a hem or binding and shall employ a drawstring or elastic binding to hold the cover on the ironing board. Additional tie tapes may be furnished, at the option of the manufacturer.

Drawstring or elastic binding

A drawstring or elastic binding shall be provided, and shall be of sufficient durability and strength to hold the cover and pad to the ironing board under normal use. Drawstrings shall be encased in an edge hem or binding, shall extend around the entire perimeter of the cover, and shall extend a minimum of 4 inches (10.2 cm) beyond the opening at each end of the hem or binding. Elastic bindings shall be securely sewn around the entire perimeter of the cover.

Ironing board cover cloth

The base cloth shall have a minimum yarn count per inch (per 2.5 cm) of 50 x 50 and minimum weight of 1.4 oz/yd2 (83.3 g/cm2) before Teflon treatment or silicone-aluminum coating. The coating shall be uniformly applied to the face of the cover and shall not crock, transfer, or rub off during normal use. The coated cloth shall show no pinholes when held up to a bright light.

Workmanship. The finished ironing board, pad, and cover shall be clean, well made, and free of any defect affecting appearance, function or serviceability. The finished ironing board shall be free of all burrs and sharp edges. The finished ironing board pad and ironing board cover shall be free of tears, cuts, holes, weak spots, thin spots, skipped stitches, open seams, puckers, or other fabric or construction defects.

Unit of Issue – EA (each)

NSN: 7290-00-893-7339

HANDCART, MAIL: Shall be a caster-mounted metal frame with two removable wire baskets in accordance with the following salient characteristics:

Material. Tubing, angle, strip, rod, and wire shall be carbon steel in accordance with American Iron and Steel Institute (AISI) 1010, 1015, 1016, 1018, or 1020 (Unified Numbering System (UNS) G10100, G10150, G10160, G10180, or G10200).

Supporting structure. The frame and handle shall be 7/8 inch, 18 gauge, 1 inch, 16 or 18 gauge, or 1 inch by 1-1/2 inch, 16 gauge.

Dimensions. The mail handcart dimensions, in inches, shall be within the following ranges. The width and length dimensions of the baskets shall be sized to properly fit the overall width and length dimensions of the cart frame.

Overall Upper Basket Lower BasketHeight 1/ 36 - 42 10 - 12 5 - 8Width 17 - 24 17 - 24 17 - 24Length 2/ 32 - 43 25 - 36 25 - 36

1/ Overall height measured at rear of cart frame.2/ Overall length measured from front of frame to back of rear wheel.

Frame. The frame shall be rigid and boltless. The handle may be an integral part of the frame, welded to the frame, or bolted to the frame. Alternately the handle may be a snap on design held securely in place with a spring pin insert.

Baskets. The removable baskets shall be rectangular and made from wire mesh. Frame wire shall be 6 gauge (minimum). Mid-frame wire shall be shall be 6 gauge (minimum). Cross wire shall be 11 gauge (minimum). Snap-on adjustable file guide bars shall be furnished with the upper basket.

Casters and wheels. The cart shall have two 4-inch or 5-inch front swiveling rubber casters and two 10-inch non-swiveling semi-pneumatic rear wheels. Casters and wheels shall be bolted to the frame or may be attached by cart frame tubing staked to the caster stems.

Finish. All components of the mail handcart shall be treated with the manufacturer's commercial standard rust and corrosion proofing treatment.

Assembly. The mail handcart shall be shipped either unassembled or fully assembled and ready to use.

Workmanship. The mail handcart shall be free from sharp edges, projections, and defects which might impair serviceability or appearance or endanger the health or safety of users. All component parts shall fit properly with applicable component parts. All component parts shall be physically and functionally interchangeable without the need for modification within the same model number mail handcart.


NSN: 7290-01-369-7966

FLATIRON, ELECTRIC (STEAM): Shall be in accordance with the latest revisions of UL Standards 1005, 498, and 817, and shall have the following characteristics:

TYPE - Spray/Steam/Dry.CORD - 3-conductor cord (2 conductor with grounding conductor) with 3-terminal (male prong) plug.LOAD RATING - 125 Volts, 15-Amp, 50-60 Hz, 16 AWG.VOLTAGE - 120 volts AC.

CORD: NEC Flexible, Type HPN, 2 conductor with additional grounding conductor shall be used and conform to the requirements of UL Standard 1005.

PLUG: 3-terminal (male prong), non-locking, non-polarized, integrally molded.

NOTE: Removable pin terminal type connection shall not be used.

SALIENT CHARACTERISTICS: The flatiron shall have a smooth, snag-free sole plate, temperature selector, push button spray, heel rest, button nook, and water level window or transparent water tank.

MARKINGS AND LABELS: If the flatiron is modified from the original UL listed manufactured flatiron, all of the original manufacturer’s names, labels, logos, care instructions, fabric guides, and inkjet or “molded

in” markings and all UL labels and markings shall be completely and permanently removed from each flatiron.

FABRIC GUIDE LABEL: Each flatiron shall contain a permanent, waterproof fabric guide label, centered on the upper surface of the flatiron. If the flatiron is modified from the original UL listed manufactured flatiron, the fabric guide label shall be in the same format as and contain the same information as the original manufacturer's label, and the fabric guide label shall contain the name and address of the company modifying the flatiron (the company installing the three prong wire and cord). The name and address shall be located on the bottom portion of the fabric guide label. If the flatiron is modified from the original UL listed manufactured flatiron, the fabric guide label shall contain no reference to the original manufacturer's names, markings, or model numbers, or to UL logos or markings.

NOTE: The fabric guide label shall be consistent with information listed in the care and use instruction booklet.

CARE AND USE INSTRUCTION BOOKLET: Each flatiron shall be accompanied by a care and use instruction booklet. The care and use instructions shall be in the same format as and contain the same information as the care and use information furnished with the original manufacturer's flatiron. If the flatiron is modified from the original UL listed manufactured flatiron, no manufacturers' names, markings, model numbers, or logos shall appear anywhere in the instruction booklet.

HAZARDOUS MATERIALS: The flatiron components shall be completely free of all asbestos material.

WORKMANSHIP: The irons shall contain no dents, cracks, scratches, loose screws or parts, and shall have no defects that may affect performance or serviceability. The bottom plate shall be smooth and flat with no burrs, scratches, or edges sharp enough to damage any cloth. The power supply cord and plug shall be free from cracks, cuts, chips, or worn insulation. The supply cord connections at the base of the flatiron and at the plug shall not be loose or damaged. The plug contacts shall not be corroded or damaged. The flatiron shall be manufactured to preclude any possible safety hazard.


NSN: 8105-00-922-9469

ITEM NAME BAG, PILOT RELIEF (UNISEX)

IAW MIL-B-83665

OVERALL LENGTH 12.0 INCHES OVERALL WIDTH 7.0 INCHES OVERALL THICKNESS 0.5 INCHES BAG TYPE UNISEX, COMPACT, LIGHTWEIGHT, EASY TO STORE.

LEAK-PROOF WITH AIRTIGHT SEALING SYSTEM THAT TRAPS WASTE AND ODOR.

SPECIAL FEATURES ABSORBENT HYDROPHILIC GRANULATED POWDER. DISPOSABLE

EXCEPTION TO THE SPECIFICATION:DELETE SECTION 5. PREPARATION FOR DELIVERY IN ITS ENTIRETY.

UI: EA

NSN: 8510-01-490-7318

SKIN CARE EMOLLIENT CREAM: Shall be GOJO Industries Aquell moisturizing lotion p/n 3828-12, or equal, in accordance with the following characteristics:

Dermatologist-tested moisturizing lotion in a 16-ounce pump bottle. Contains emollients, mineral oil, aloe, and vitamins A and E to protect skin and leave hands feeling soft and smooth.


Unit of Issue – BX (Box of twelve 16-ounce pump bottles)

NSN: 8520-00-082-2146

HAND CLEANER (WATERLESS, CREAM FORM): Shall be a one (1) pound container of hand cleaner in accordance with the following characteristics:

The hand cleaner shall be a cream waterless hand cleaner for removing grease and industrial soils from the hands and shall be an odorless or mildly scented cream. It shall not smell rancid or have odors characteristic of ammonia or kerosene and shall not irritate unabraded skin when used as directed on the container.

pH: The pH of a 5 percent by weight suspension of the hand cleaner in distilled water shall be 5.5 to 9.5.

Free alkali: The hand cleaner shall contain no more than 0.1 percent by weight free alkali as NaOH, see ASTM D 820.

Heat stability: During heating at 38C for 72 hours, the hand cleaner shall not separate, change color or turn rancid.

Freeze-thaw stability: During three cycles of freezing at -10C for 16 hours and thawing at 22C for 8 hours, the hand cleaner shall not separate into components.

Performance: Within 120 seconds, 2.5 grams of hand cleaner shall suspend and completely remove from the palms of the hands a thin, uniform layer of asphalt 30 mm in diameter, which has been applied to the palm of each hand. (Form asphalt into a rod, dip in Stoddard solvent and apply to palms). The asphalt used in the testing shall meet the requirements of ASTM D 312, Type II, or shall be commercial petroleum asphalt having the following characteristics:

Softening point (ASTM D 36), 170F to 195FPenetration (ASTM D 5) at 77F, in Penetration Units: 25 to 85.Solubility in carbon tetrachloride, 98% minimum.

Viscosity: The hand cleaner shall have a viscosity of not less than 400,000 centipoise at 25C.

The hand cleaner shall comply with the Federal Food, Drug, and Cosmetic Act and the regulations published under the Act (21 CFR Part 1, General Enforcement Regulations of the Federal Food, Drug, and Cosmetic Act).

Shelf life code: 6. Maximum age on delivery shall not exceed three (3) months from date of manufacture. Date of re-inspection shall be twenty-four (24) months after date of manufacture.

Unit of Issue – BX (Box containing twelve 1-lb

NSN: 8520-00-129-0803

SOAP, TOILET (FOR HARD AND SOFT WATER): Bars of toilet soap, milled and mildly perfumed, shall meet the requirements specified in the following table when tested in accordance with ASTM D 820, Standard Test Methods for Chemical Analysis of Soaps Containing Synthetic Detergents.

Characteristic RequirementMoisture, maximum percent 13.0Synthetic detergent, minimum percent 25.0Sum of soap and synthetic Detergent, minimum percent 60.0Free alkali (as NaOH), maximum percent 0.1

The issue of ASTM D 820 in effect on the date of the solicitation shall be used to determine compliance with these requirements.

Soap bar: 3-3/4 1/2 ounces


Unit of Issue – BX (Box of seventy-two 3.75-ounce individually wrapped bars)

NSN: 8520-00-225-8563

HAND CLEANER (WATERLESS, CREAM FORM): Shall be a five (5) ounce tube of antimicrobial hand cleaner in accordance with the following characteristics:

The hand cleaner shall be a cream waterless hand cleaner for removing grease and industrial soils from the hands and shall be an odorless or mildly scented cream. It shall not smell rancid or have odors characteristic of ammonia or kerosene and shall not irritate unabraded skin when used as directed on the container.

pH: The pH of a 5 percent by weight suspension of the hand cleaner in distilled water shall be 5.5 to 9.5.

Free alkali: The hand cleaner shall contain no more than 0.1 percent by weight free alkali as NaOH, see ASTM D 820.

Heat stability: During heating at 38C for 72 hours, the hand cleaner shall not separate, change color or turn rancid.

Freeze-thaw stability: During three cycles of freezing at -10C for 16 hours and thawing at 22C for 8 hours, the hand cleaner shall not separate into components.

Performance: Within 120 seconds, 2.5 grams of hand cleaner shall suspend and completely remove from the palms of the hands a thin, uniform layer of asphalt 30 mm in diameter, which has been applied to the palm of each hand. (Form asphalt into a rod, dip in Stoddard solvent and apply to palms). The asphalt used in the testing shall meet the requirements of ASTM D 312, Type II, or shall be commercial petroleum asphalt having the following characteristics:

Softening point (ASTM D 36), 170F to 195FPenetration (ASTM D 5) at 77oF, in Penetration Units: 25 to 85.Solubility in carbon tetrachloride, 98% minimum.

Viscosity: The hand cleaner shall have a viscosity of not less than 400,000 centipoise at 25C.

Antimicrobial activity: A 25 percent by weight suspension of the hand cleaner in distilled water shall inhibit the growth of Staphylococcus aureus (ATCC 6538), Salmonella typhi (ATCC 6539) and Trichophyton mentagrophytes (ATCC 9533). See “Disinfection, Sterilization and Preservation” by Seymour S. Block, Second Edition, 1977, Lea and Febiger; pp 95-96 “Agar Cup-Plate Method for Bacteriostatic Activity” and p 142 “Seeded Agar Cup-Plate Method for Fungistatic Activity.”

The hand cleaner shall comply with the Federal Food, Drug, and Cosmetic Act and the regulations published under the Act (21 CFR Part 1, General Regulations for the Enforcement of the Federal Food, Drug and Cosmetic Act).


Unit of Issue – BX (Box containing twenty-four 5-ounce tubes of hand cleaner)

NSN: 8520-00-228-0598

SOAP, TOILET: Shall be National Industries for the Blind Skilcraft p/n 1064013 with the following characteristics:

Gentle and efficient liquid soap contains 15% coconut oil, and is specially formulated to be dispensed from liquid soap dispensers undiluted without clogging or dripping. Mildly scented.

The hand cleaner shall have a minimum biobased content of 64%. The minimum biobased content requirement shall be based on the amount of qualifying biobased carbon in the product as a percent of the weight (mass) of the total organic carbon in the finished product as specified in 7 CFR 2902.18.


Unit of Issue – BX (Box having six 1-gallon containers)NSN: 8520-00-531-6484

SOAP, TOILET: Shall be a high-grade, milled cake soap, either colored or uncolored, mildly perfumed, as free as possible from water, thoroughly saponified, and well compressed in firm, smooth cakes, primarily for use with soft water to clean the skin. Shall lather freely when used with cold, soft water. Shall conform to the requirements in the table below regarding chemical composition. The percentage of matter volatile at 105C shall be calculated on the basis of the soap as received, but all other constituents shall be calculated on the basis of material containing 15% of matter volatile at 105C.

Milled Toilet Soap, Chemical CompositionMoisture and matter volatile at 105C, max, % 15.0Sum of free alkali, total matter insoluble in alcohol, and sodium chloride, max, %

3.0

Free alkali, calculated as NaOH, max, % 0.1Matter insoluble in water, max, % 1.0Unsaponified saponifiable matter (free fat), max, % 0.3Rosin acids, and foreign matter noneAnhydrous soap content, min % 83.0

5.0 0.5 ounces per cake


Unit of Issue – HD (One hundred cakes of soap per box)

NSN: 8520-00-550-6417

SOAP GRIT (CAKE PUMICE SOAP): Shall be in accordance with the following characteristics:

The soap shall be pumice soap in cake form for removing oil, grease, and other heavy occupational soils from the hands. The finished product shall be a mixture of soap and finely ground pumice in compressed cake form. The grit soap cakes shall be uniform in size, homogeneous in appearance and texture, firm and not crumbly, and free from any gouges, holes, breaks, cracks or chipped surfaces. The grit soap shall be odorless or mildly perfumed. Each cake shall weight 5.0 ± 0.5 ounces per cake. The maximum for free fatty acid shall be 3.0 percent and the maximum for the material retained on a No. 80 sieve shall be 1.0 percent.

Exception to DoD 4140-27-M, delete paragraph 2-12, and substitute the following:

“2-12. Any soap delivered from a contractor not having at least 17 months shelf-life remaining shall be considered non-conforming.”

Maximum age on delivery – 7 months from date of manufacture (see exception to DoD 4140-27-M).

Shelf life code: 6. Maximum age on delivery shall not exceed SEVEN (7) months from date of manufacture. Date of re-inspection shall be twenty-four (24) months after date of manufacture.

Unit of Issue – HD (One hundred cakes of soap per box)NSN: 8520-00-551-0375

SOAP, TOILET: Shall be a high-grade, milled cake soap, either colored or uncolored, mildly perfumed, as free as possible from water, thoroughly saponified, and well compressed in firm, smooth cakes, primarily for use with soft water to clean the skin. Shall lather freely when used with cold, soft water. Shall conform to the requirements in the table below regarding chemical composition. The percentage of matter volatile at 105ºC shall be calculated on the basis of the soap as received, but all other constituents shall be calculated on the basis of material containing 15% of matter volatile at 105ºC.

Milled Toilet Soap, Chemical CompositionMoisture and matter volatile at 105ºC, max, % 15.0Sum of free alkali, total matter insoluble in alcohol, and sodium chloride, max, % 3.0Free alkali, calculated as NaOH, max, % 0.1Matter insoluble in water, max, % 1.0Unsaponified saponifiable matter (free fat), max, % 0.3Rosin acids, and foreign matter noneAnhydrous soap content, min % 83.0

0.75 ± 0.25 ounce cake of soap individually wrapped

Shelf life code: 8. Maximum age on delivery shall not exceed seven (7) months from date of manufacture.Date of re-inspection shall be forty-eight (48) months after date of manufacture.

Unit of Issue – MX (One thousand (1000) individually wrapped cakes of soap per box).

NSN: 8520-01-303-4037

TOOTHPASTE: Fluoride toothpaste shall be in accordance with the following characteristics:

Ingredients. All material used in making the toothpaste shall be USP, NF, food or cosmetic grade quality. The finished product shall conform in all respects to the provisions of the Federal Food, Drug and Cosmetic Act (21 CFR), including the Drug Facts labeling requirements in 21 CFR Section 201.66.

Consistency. The toothpaste shall be a homogenous mixture and shall be free of lumps or particles which are palpable in the mouth as separate or discrete particles.

PH. The pH of the toothpaste shall be not less than 4.2 and not greater than 10.0 when tested as specified in ASTM E 70, using one part by weight of toothpaste dissolved in four parts by weight of distilled water as the test solution. The issue of ASTM E 70 in effect on the date of the solicitation shall be used to determine compliance with these requirements.

ASTM standards are available from the American Society for Testing and Materials, 100 Barr Harbor Drive, West Conshohocken, PA 19428-2959.

Color. The toothpaste shall be white or made with FDA certified dyes.

Appearance. The toothpaste shall be opaque or translucent or a combination of both.

Flavor. The toothpaste shall have a distinct and pleasant flavor.

Safety. When used in normal manner the toothpaste shall not cause injury or irritation to the teeth, gums or mucous membranes of the mouth.

Ease of extrusion. It shall be possible to extrude not less than 95 percent by weight of the toothpaste from the tube in a continuous mass at a temperature of 10 C without the application of excessive force which would damage the tube.

Stability. The toothpaste shall not segregate, ferment or deteriorate when cooled in a stoppered test tube to -15 C for 72 hours or heated in a stoppered test tube to 45 C for 72 hours.

Fluoride. The toothpaste shall contain a fluoride compound and shall have formulation fulfilling the guidelines of the OTC Anticaries Drug Monograph, have an approved new Drug Application, or Seal of Approval of the ADA council on Dental Therapeutics. The name of the fluoride compound shall be marked on the tube.


Unit of Issue – DZ (Dozen tubes, each containing 2.7 to 3.5 ounces (by weight) of toothpaste)

NSN: 8520-01-303-4038

CREAM, SHAVING: Brushless shaving cream in 2-ounce tube shall be a smooth, clean, homogeneous cream, shall not contain any grit, and shall be packaged in containers that will not be corroded by the contents.

The shaving cream shall meet the requirements specified in the following table when tested in accordance with ASTM D 460 Standard Test Methods for Sampling and Chemical Analysis of Soaps and Soap Products.

Characteristic RequirementMoisture, maximum percent 60Free alkali (as NaOH), maximum percent 0Free fatty acid (as stearic acid), minimum percent 25

The issue if ASTM D 460 in effect on the date of the solicitation shall be used to determine compliance with these requirements.

Material shall not contain ingredients that are classified as hazardous according to the Occupational Safety and Health Administration, 29 CFR Part 1910.

Shelf life code: 7. Maximum age on delivery shall not exceed five (5) months from date of manufacture. Date of re-inspection shall be thirty-six (36) months after date of manufacture.

Unit of Issue – DZ (One dozen 2-ounce tubes)

NSN: 8520-01-303-4039

CREAM, SHAVING: Brushless shaving cream in 4.5-ounce tube shall be a smooth, clean, homogeneous cream, shall not contain any grit, and shall be packaged in containers that will not be corroded by the contents.

The shaving cream shall meet the requirements specified in the following table when tested in accordance with ASTM D 460 Standard Test Methods for Sampling and Chemical Analysis of Soaps and Soap Products.

Characteristic RequirementMoisture, maximum percent 60Free alkali (as NaOH), maximum percent 0Free fatty acid (as stearic acid), minimum percent 25

The issue if ASTM D 460 in effect on the date of the solicitation shall be used to determine compliance with these requirements.

Material shall not contain ingredients that are classified as hazardous according to the Occupational Safety and Health Administration, 29 CFR Part 1910.

Shelf life code: 7. Maximum age on delivery shall not exceed five (5) months from date of manufacture. Date of re-inspection shall be thirty-six (36) months after date of manufacture.

Unit of Issue – DZ (One dozen 4.5-ounce tubes)

NSN: 8520-01-303-6438

TOOTHPASTE: Regular (no fluoride) toothpaste shall be in accordance with the following characteristics:

Ingredients. All material used in making the toothpaste shall be USP, NF, food or cosmetic grade quality. The finished product shall conform in all respects to the provisions of the Federal Food, Drug and Cosmetic Act (21 CFR 1).








Ease of extrusion. It shall be possible to extrude not less than 95 percent by weight of the toothpaste from the tube in a continuous mass at a temperature of 10 C without the application of excessive force which would damage the tube.

Tube. The toothpaste shall be provided in a tube, each tube containing 1.5 ± 0.1 ounce (by weight) of toothpaste.

Stability. The toothpaste shall not segregate, ferment or deteriorate when cooled in a stoppered test tube to -15 C for 72 hours or heated in a stoppered test tube to 45 C for 72 hours.


Unit of Issue – DZ (Dozen)

NSN: 8520-01-370-2162

HAND CLEANER: Shall be Simple Green hand cleaner gel p/n 42128, or equal, in accordance with the following characteristics:

Heavy duty hand cleaner gel in a one-gallon pump bottle. Contains surfactants, lanolin, and pumice. Works with or without water to remove grease, oil, and dirt from hands. Non-toxic, biodegradable and non-flammable. Has a pH of 7.7 ± 1.0 (for a 10% solution).

Unit of Issue – BX (Four one-gallon pump bottles per box)

NSN: 8520-01-370-4284

HAND CLEANER: Shall be Simple Green hand cleaner gel p/n 42675, or equal, in accordance with the following characteristics:

Heavy duty hand cleaner gel in a 6.75 ± 0.5-ounce squeeze tube. Contains surfactants, lanolin, and pumice. Works with or without water to remove grease, oil, and dirt from hands. Non-toxic, biodegradable and non-flammable. Has a pH of 7.7 ± 1.0 (for a 10% solution).

Unit of Issue – BX (Twelve 6.75 ± 0.5-ounce squeeze tubes per box)

NSN: 8520-01-371-0047

HAND CLEANER: Shall be Permatex p/n 14104, or equal, in accordance with the following characteristics:

Heavy-duty hand cleaner removes ink, grease, adhesives, varnish, hydraulic fluids, carbon, and other tough industrial soils. Fortified with emollients to prevent drying and cracking. Coconut scented.

Unit of Issue - BX (Box of six 4.0-lb cans)

NSN: 8520-01-378-3090

SKIN CLEANSER: Shall be Travis Association for the Blind Skilcraft p/n 1720-12, or equal, in accordance with the following characteristics:

Mild cleansing lotion soap in an 800 mL pouch. Gently removes light soil leaving hands clean and refreshed. PH-balanced for skin care and formulated for frequent and general use. Pink, synthetic detergent formula.

Shall be compatible for use with GOJO wall dispenser 9033, which is available under NSN 4510-01-521-9868 for a single dispenser, and NSN 4510-01-521-9867 for a box of 12 dispensers.

Unit of Issue – BX (twelve 800 mL pouches per box)

NSN: 8520-01-381-1914

SOAP, TOILET: Shall be Cavalier Inc. p/n 997345, or equal, in accordance with the following characteristics:

Cream hand soap with lanolin is for use in standard 800-mL soap dispensers.

Unit of Issue – BX (Box containing twelve 800-mL refill bags of liquid soap)

NSN: 8520-01-411-0628

SOAP, TOILET: Shall be a high-grade, milled cake soap, either colored or uncolored, mildly perfumed, as free as possible from water, thoroughly saponified, and well compressed in firm, smooth cakes, primarily for use with soft water to clean the skin. Shall lather freely when used with cold, soft water. Shall conform to the requirements in the table below regarding chemical composition. The percentage of matter volatile at 105C shall be calculated on the basis of the soap as received, but all other constituents shall be calculated on the basis of material containing 15% of matter volatile at 105C.

Milled Toilet Soap, Chemical CompositionMoisture and matter volatile at 105C, max, % 15.0Sum of free alkali, total matter insoluble in alcohol, and sodium chloride, max, %

3.0

Free alkali, calculated as NaOH, max, % 0.1Matter insoluble in water, max, % 1.0Unsaponified saponifiable matter (free fat), max, % 0.3Rosin acids, and foreign matter noneAnhydrous soap content, min % 83.0

3.0 0.50 ounce cake of soap individually wrapped.


Unit of Issue – BX (Box of seventy-two 3.0-ounce individually wrapped cakes)

NSN: 8520-01-415-2931

HAND CLEANER: Shall be Ecolab Inc. Part Number 14894, or equal, in accordance with the following characteristics:

Antibacterial liquid hand cleaner is designed for employee restroom and kitchen handwashing sinks. Contains alcohol as the active antibacterial ingredient. Mild, moisturizing formula is intended to clean and remove bacteria from the hands of food service personnel. Excellent degreasing formula has good hand coverage to help with hand-washing compliance. Light, honey almond scent. Sealed cartridge refill system eliminates waste and spillage. For use with the Ecolab Clean and Smooth dispenser.


Unit of Issue - BX (Box containing sixteen 450 mL cartridges of hand cleaner)

NSN: 8520-01-422-2216

TOWELETTE, SKIN CLEANSING: Dymon Inc. SCRUBS in-a-Bucket p/n 42272, or equal, in accordance with the following characteristics:

Premoistened hand cleaner towel, treated with grease-cutting soil lifting formulation and skin conditioners, to dissolve adhesives, caulk, epoxy, ink and dye, paint, sealant, tar, urethane, wax and polyurethane.

Natural citrus fragrance.

Unit of Issue – BX (6 durable plastic self-dispensing type containers with handle containing 72 towelettes per container)

NSN: 8520-01-425-5328

HAND CLEANER: Shall be Zep Double Play, p/n 095024, or equal, in accordance with the following characteristics:

Heavy-duty hand cleaner with natural citrus, lanolin, and pumice scrubs away grease and grime. For use with dispenser 4510-01-441-2117. For industrial and institutional use.

Shelf life code: 6. Maximum age on delivery shall not exceed three (3) months from date of manufacture. Date of re-inspection shall be twelve (12) months after date of manufacture.

Unit of Issue – BX (Box containing four 1-gallon jugs)

NSN: 8520-01-432-2618

HAND CLEANER: Shall in accordance with the following characteristics:

For general cleaning of hands, liquid, with fragrance added, formulated to quickly emulsify, rich lather with mild detergents, with moisturizers, pH balanced, provided in 1-gallon container with handle. Can be used in all liquid soap dispenser and central dispensing systems with no dilution.



Unit of Issue – BX (Box containing four 1-gallon containers)

NSN: 8520-01-454-1144

TOWELETTE, SKIN CLEANSING: Heavy-duty 6.3”x6.25” towelettes with glycerin and aloe, pre-moistened in pop-up dispenser, fifty (50) wipes per dispenser.

Unit of Issue – BX (Box containing twelve (12) dispensers, each dispenser containing fifty (50) towelettes)

NSN: 8520-01-458-0767

HAND CLEANER: Shall be Travis Association for the Blind Skilcraft p/n 1935-04, GOJO Industries, Inc., p/n 0955-04, or equal, in accordance with the following characteristics:

Petroleum-free, quick-acting lotion formula in a 1-gallon bottle with pump dispenser. Contains pumice scrubbing particles for cleaning industrial soils, medium dirt and grease. Contains baby oil and an orange citrus formula with lanolin, aloe, and jojoba to help protect hands.


Unit of Issue – BX (four 1-gallon pump bottles per box)

NSN: 8520-01-490-7322

SOAP, HARD: Shall be Dial Corporation p/n 1092384100, or equal, in accordance with the following characteristics:

Hypoallergenic hand and body soap3.0 ± 0.5-ounce bar unwrapped

Unit of Issue – BX (Box of 200 unwrapped bars of soap

NSN: 8520-01-490-7324

SOAP, HARD: Shall be Dial Corporation p/n 109230009800, or equal, in accordance with the following characteristics:

Antibacterial deodorant bar soapHand and body barRinses clean with a fresh scent and rich lather2.5-ounce bar unwrapped

Unit of Issue – BX (Box of 200 unwrapped bars of soap)

NSN: 8520-01-490-7358

HAND SANITIZER: Shall be GOJO Industries, Purell Instant Hand Sanitizer p/n 9651-24, or equal, in accordance with the following characteristics:

Hand sanitizer in 4.25 ± 0.25-ounce squeeze bottle, active ingredient 62% ethyl alcohol. Contains moisturizers and vitamin E. Kills 99.99% of most common germs that may cause illness, in as little as 15 seconds. Convenient, portable individual size. Use anytime, anyplace, without water or towels. Leaves hands feeling refreshed without stickiness or residue.


Unit of Issue – BX (Box of twenty-four 4.25 ± 0.25-ounce squeeze bottles)

NSN: 8520-01-490-7365

HAND SANITIZER: Shall be GOJO Industries, Purell Instant Hand Sanitizer p/n 3659-12, or equal, in accordance with the following characteristics:

Hand sanitizer in 12-ounce pump bottle, active ingredient 62% ethyl alcohol. Contains moisturizers and vitamin E. Kills 99.99% of most common germs that may cause illness, in as little as 15 seconds. Convenient, portable individual size. Use anytime, anyplace, without water or towels. Leaves hands feeling refreshed without stickiness or residue.



NSN: 8520-01-490-7367

SOAP ANTIBACTERIAL: Shall be GOJO Industries, Micrell antibacterial lotion soap p/n 9755-04 or equal in accordance with the following characteristics:

Antibacterial lotion soap in one-gallon jug contains 0.3% chloroxylenol (antimicrobial agent) and an effective degreaser. Lightly scented, non-irritating formula.


Unit of Issue – GL (Gallon)

NSN: 8520-01-490-7370

SOAP ANTIBACTERIAL: Shall be GOJO Industries, Micrell antibacterial lotion soap p/n 9759-12, or equal, in accordance with the following characteristics:

Antibacterial lotion soap in a 12-ounce pump bottle contains 0.3% chloroxylenol (antimicrobial agent) and an effective degreaser. Lightly scented, non-irritating formula.



NSN: 8520-01-521-4206

SOAP, TOILET: Shall be Ecolab Inc. p/n 23671, or equal, in accordance with the following characteristics:

Mild hand soap that removes soil on hands. Honey-almond fragrance.

Shelf life code: 4. Maximum age on delivery shall not exceed two (2) months from date of manufacture. Date of re-inspection shall be twenty-four (24) months after date of manufacture.

Unit of Issue – BX (Six 750-mL containers of liquid hand soap per box)

NSN: 8520-01-522-0828

HAND SANITIZER: Shall be Travis Association for the Blind Skilcraft p/n 1850-08, GOJO Industries, Inc., p/n 2156-8, or equal, in accordance with the following characteristics:

Instant hand sanitizer in a 1000-mL pouch has a pleasant fragrance, and is non-toxic, dye-free and hypoallergenic. Contains a unique blend of ethyl alcohol and moisturizers. Sanitizes hands when soap and water are not available, leaving hands feeling soft and refreshed without a sticky or tacky residue.


Unit of Issue – BX (eight 1000-mL pouches per box)

NSN: 8520-01-522-0829

SOAP, ANTIBACTERIAL: Shall be Travis Association for the Blind Skilcraft p/n 1799-12, GOJO Industries, Micrell antibacterial lotion soap p/n 9757-12, or equal, in accordance with the following characteristics:

Specially formulated anti-bacterial soap in an 800-mL pouch. With a quick-acting anti-microbial agent to kill germs in seconds. Pleasant fragrance is non-irritating and leaves hands feeling soft and refreshed.

Shall be compatible for use with GOJO wall dispenser 9721, which is available from GOJO under p/n 9721-12.


Unit of Issue – BX (twelve 800-mL pouches per box)

NSN: 8520-01-522-0830


The product shall be packaged in an 800-mL pouch, have a pleasant fragrance, be non-toxic, dye-free, and hypoallergenic. The product shall contain a unique blend of ethyl alcohol, moisturizers and vitamin E. It shall sanitize hands when soap and water are not available. The product shall leave hands feeling soft and refreshed without a sticky or tacky residue.

The product shall be compatible for use with GOJO wall dispenser 9621, which is available from GOJO under p/n 9621-12 for a box of 12 dispensers.

Unit of Issue – BX (twelve 800-mL pouches per box)

NSN: 8520-01-522-0834

SOAP, ANTIBACTERIAL: Shall be Travis Association for the Blind Skilcraft p/n 1805-08, GOJO Industries, Micrell antibacterial lotion soap p/n 2157-08, or equal, in accordance with the following characteristics:

Specially formulated anti-bacterial lotion soap with moisturizers in a 1000-mL pouch. With a quick acting anti-microbial agent to kill germs in seconds. Pleasant fragrance is non-irritating and leaves hands feeling soft and refreshed.

Shall be compatible for use with GOJO wall dispenser 2125, which is available from GOJO under p/n 2125-06.



NSN: 8520-01-522-0835


The product shall be instant hand sanitizer in a 2-ounce squeeze bottle has a pleasant fragrance, and is non-toxic, dye-free, and hypoallergenic. It shall contain a unique blend of ethyl alcohol and moisturizers. It shall sanitize hands when soap and water are not available, leaving hands feeling soft and refreshed without a sticky or tacky residue.

The hand sanitizer shall have a minimum biobased content of 73%. The minimum biobased content requirement shall be based on the amount of qualifying biobased carbon in the product as a percent of the weight (mass) of the total organic carbon in the finished product as specified in 7 CFR 3201.18.

Unit of Issue – BX (twenty-four 2-ounce squeeze bottles per box)

NSN: 8520-01-522-0837

SKIN CLEANSER: Shall be Travis Association for the Blind Skilcraft p/n 1744-04, GOJO Industries, Inc., p/n 2217-04, or equal, in accordance with the following characteristics:

Mild cleansing lotion soap in a 2000-mL pouch. Gently removes light soil leaving hands clean and refreshed. PH-balanced for skin care and formulated for frequent and general use. Pink, synthetic detergent formula.


Unit of Issue – BX (four 2000-mL pouches per box)

NSN: 8520-01-522-0838

SKIN CLEANSER: Shall be Travis Association for the Blind Skilcraft p/n 1737-08, GOJO Industries, Inc., p/n 2117-08, or equal, in accordance with the following characteristics:

Mild cleansing lotion soap in a 1000-mL pouch. Gently removes light soil leaving hands clean and refreshed. PH-balanced for skin care and formulated for frequent and general use. Pink, synthetic detergent formula.



NSN: 8520-01-522-0839

SKIN CLEANSER: Shall be Travis Association for the Blind Skilcraft p/n 1751-12, or equal, in accordance with the following characteristics:

Mild cleansing lotion soap in a 12-ounce pump bottle. Gently removes light soil leaving hands clean and refreshed. PH-balanced for skin care and formulated for frequent and general use. Pink, synthetic detergent formula.

Unit of Issue – BX (twelve 12-ounce pump bottles per box)

NSN: 8520-01-522-0840


Petroleum-free, quick-acting lotion formula in a 1-gallon bottle with pump dispenser. Contains pumice scrubbing particles for cleaning industrial soils, medium dirt and grease. Contains baby oil and an orange citrus formula with lanolin, aloe, and jojoba to help protect hands.


Unit of Issue – BX (six 1/2-gallon bottles per box)

NSN: 8520-01-522-3885


Instant hand sanitizer with Aloe in an 800-mL pouch has a pleasant fragrance, and is non-toxic, dye-free, and hypoallergenic. Contains a unique blend of ethyl alcohol, Aloe, and specially formulated moisturizers. The product shall sanitize hands when soap and water are not available, leaving hands feeling soft and refreshed without a sticky or tacky residue.

The product shall be compatible for use with Gojo wall dispenser 9621, which is available from Gojo under p/n 9621-12 for a box of 12 dispensers.

Unit of Issue – BX (twelve 800-mL pouches per box)NSN: 8520-01-522-3886


Instant hand sanitizer with Aloe in a 4-ounce squeeze bottle has a pleasant fragrance, and is non-toxic, dye-free, and hypoallergenic. Contains a unique blend of ethyl alcohol, Aloe, and specially formulated moisturizers. Sanitizes hands when soap and water are not available, leaving hands feeling soft and refreshed without a sticky or tacky residue.

Unit of Issue – BX (twenty-four 4-ounce squeeze bottles per box)

NSN: 8520-01-522-3887

HAND SANITIZER: Shall be Travis Association for the Blind Skilcraft p/n 3143-0074, GOJO Industries, Inc., p/n 9639-12, Gojo Industries, Inc. p/n 3639-12, or equal, in accordance with the following characteristics:

Instant hand sanitizer with Aloe in a 12-ounce pump bottle has a pleasant fragrance, and is non-toxic, dye-free, and hypoallergenic. Contains a unique blend of ethyl alcohol, Aloe, and specially formulated moisturizers. It shall sanitize hands when soap and water are not available, leaving hands feeling soft and refreshed without a sticky or tacky residue.

Unit of Issue – BX (twelve 12-ounce pump bottles per box)

NSN: 8520-01-522-3888


Instant hand sanitizer with aloe in a 1000-mL pouch has a pleasant fragrance, and is non-toxic, dye-free, and hypoallergenic. Contains a unique blend of ethyl alcohol, aloe, and specially formulated moisturizers. Sanitizes hands when soap and water are not available, leaving hands feeling soft and refreshed without a sticky or tacky residue.

Shall be compatible for use with Gojo wall dispenser 2120, which is available under NSN 4510-01-521-9866 for a single dispenser, and NSN 4510-01-521-9870 for a box of 6 dispensers.


NSN: 8520-01-556-2576


Smooth, orange foaming hand wash with germ-killing power in an orange blossom fragrance.

Shall be compatible for use with Gojo wall dispenser 5150, which is available under NSN 4510-01-551-2864 for a box of 6 dispensers, and NSN 4510-01-551-2865 for a single dispenser.


Unit of Issue – BX (three 1250 mL containers per box)

NSN: 8520-01-556-2577


Mild, biodegradable foam soap and lotion formula used for general hand cleaning. Meets the Green Seal and EcoLogo environmental standard for institutional hand cleaners based on their reduced human and aquatic toxicity and reduced smog production potential.



Unit of Issue – BX (three 1250 mL containers per box)

NSN: 8520-01-556-2834


Instant hand sanitizer foam kills 99.99% of most germs. Thick, rich foam clings to your hands, contains moisturizers. The product shall meet the CDC Guideline for Hand Hygiene in Health-Care Setting, JCAHO guidelines, NFPA and IFCI regulations for alcohol-base hand rubs, OSHA Blood borne Pathogens Standards for hand hygiene practice. It shall be compatible with latex, nitrile, and vinyl gloves and CHG. Dermatologist tested and hypoallergenic. It shall be a fast, broad-spectrum antimicrobial efficacy and dye-free.



Unit of Issue – BX (Box of three 1200 mL containers)

NSN: 8520-01-566-2392

SANITIZER, HAND: Shall be Ecolab Inc. p/n 23674, or equal, in accordance with the following characteristics:The product shall be a foaming hand sanitizer, quaternary and alcohol formula, mild on hands and have a mild odor.

Shelf life code: 6. Maximum age on delivery shall not exceed Five (5) months from date of manufacture. Date of re-inspection shall be thirty-six (4) months after date of manufacture.

Unit of Issue – BX (Six 750-mL containers of hand sanitizer per box)NSN: 8520-01-574-6494

HAND CLEANER: Shall be Cavalier p/n 997337, in accordance with the following characteristics:

Foaming soap contains aloe, vitamin E, and tropical fragrance.

Product is listed in NAVSEA Pub. No. S6480-A4-CAT-010; U.S. Navy Surface Ship (Non-Submarine) Authorized Chemical Cleaning Products And Dispensing Systems Catalog. This is the only product under this NSN approved for use aboard US Navy ships. As such, the item is considered unique and a part number description is required.

Unit of Issue – BX (Box of six (6) 1000 mL bags)

NSN: 8530-00-162-5629

BLADE, SAFETY RAZOR, SINGLE EDGE, CARBON STEEL: The construction, configuration, and dimensions shall be those commercially accepted for single edge razor blades usable with common commercially available single edge safety razors. Each blade shall be provided with securely attached metal backing strip and be suitable for shaving human skin. Please see Figure 1 for a depiction of this type of safety razor blade.

Figure 1Single edge razor blade

The vendor supplying the product must have been marketing the product commercially for a minimum of two years.

Unit of Issue – BX (Box of 100 blades)

NSN: 8530-01-293-1387

TOOTHBRUSH, ADULT’S (MULTITUFT): Soft, straight line design toothbrush in accordance with the following characteristics:

The toothbrushes shall have a rounded leading end, shaped neck, and flat even working surface. The head, neck and handle shall be molded in one piece from Grade A quality polypropylene.

PHYSICAL CHARACTERISTIC REQUIREMENT

Block length, overall (min.) 6 inchesHead molding length (min.) 7/8 inchHead molding width, (min.) 23/64 inchThickness (min.) 3/16 inchNumber of tuft holes 30-60Filament ends per tuft (min.) 30Filament length clear of block (min.) 0.406 inchFilament diameter 0.006 - 0.008 inch

The toothbrush shall have a minimum of three rows of bristle tufts. The tufts shall be uniformly spaced and symmetrically located. The tufts shall be firmly anchored in the holes either by nickel silver slugs or by stapling.

The filaments for the tuft material shall be quality nylon. The ends of the filaments shall be rounded so that sharp points and rough edges, that could cause injury to the gums, are eliminated.

Unit of Issue – DZ (Dozen)

NSN: 8530-01-293-1388

TOOTHBRUSH, CHILD’S (MULTITUFT): Soft, straight line design toothbrush in accordance with the following characteristics:

The toothbrushes shall have a rounded leading end, shaped neck, and flat even working surface. The head, neck and handle shall be molded in one piece from quality polypropylene.

PHYSICAL CHARACTERISTIC REQUIREMENT

Block length, overall 5-1/4 to 6-1/2 inchesHead molding length 1-1/16 + 1/16 inchHead molding width, max. 23/64 + 1/64 inchThickness, max. 3/16 inchNumber of tuft holes 24-30Filament ends per tuft (min.) 40Filament length clear of block 3/8 + 1/32 inchFilament diameter 0.005 - 0.007 inch

The toothbrush shall have a minimum of three rows of bristle tufts. The tufts shall be uniformly spaced and symmetrically located. The tufts shall be firmly anchored in the holes either by nickel silver slugs or by stapling.

The filaments for the tuft material shall be quality nylon. The ends of the filaments shall be rounded so that sharp points and rough edges, that could cause injury to the gums, are eliminated.

Unit of Issue - BX (Box containing 144 toothbrushes)

NSN: 8530-01-490-7372

TOILETRIES KIT: Shall be in accordance with the following characteristics:

Shampoo and body wash – minimum 2 ouncesHair conditioner – minimum 2 ouncesHand and body lotion – minimum 2 ouncesShave cream – minimum 0.85-ouncePlastic comb – length of 6 ± 1 inch6-inch plastic toothbrush4-inch twin-edge plastic razor

Fluoride toothpaste – minimum 0.85-ounce. Fluoride toothpaste shall be in accordance with the following characteristics:

Ingredients. All material used in making the toothpaste shall be USP, NF, food or cosmetic grade quality. The finished product shall conform in all respects to the provisions of the Federal Food, Drug and Cosmetic Act (21 CFR), including the Drug Facts labeling requirements in 21 CFR Section 201.66.








Ease of extrusion. It shall be possible to extrude not less than 95 percent by weight of the toothpaste from the tube in a continuous mass at a temperature of 10o C without the application of excessive force which would damage the tube.

Stability. The toothpaste shall not segregate, ferment or deteriorate when colled in a stoppered test tube to -15o C for 72 hours or heated in a stoppered test tube to 45o C for 72 hours.

Fluoride. The toothpaste shall contain a fluoride compound and shall have formulation fulfilling the guidelines of the OTC Anticaries Drug Monograph, have an approved new Drug Application, or Seal of Approval of the ADA council on Dental Therapeutics. The name of the fluoride compound shall be marked on the tube.

Unit of Issue – BX (Box containing twelve (12) kits)

NSN: 8540-00-149-1601

ITEM NAME: NAPKIN, COCKTAIL, PAPER

OVERALL LENGTH 10.0 INCHES (+/-0.5 INCHES)OVERALL WIDTH 10.0 INCHES (+/-0.5 INCHES)COLOR WHITE OVERALL WITH FED-STD-595 GOLD No. 27043

EMBOSSED ON EDGES ONLY TO A DEPTH OF 1 INCH PLUS OR MINUS 1/8 INCH; EMBOSSING SHALL BE SIMPLE RIPPLE OR BARK TYPE PATTERN WITH MITERED CORNERS, FINISHED ON THEINSIDE WITH SIMPLE ROPE BEADING OR RIBBON TYPE EDGE FROM 1/8 TO 1/4 INCH WIDE; THE TRADEMARK OR IDENTIFICATION OF THE MANUFACTURER SHALL NOT APPEAR ON THE NAPKIN.

ORNAMENTATION THE GREAT SEAL SHALL BE PRINTED AND PLACED ON THE NAPKIN

PLY QUANTITY 3 PLY CONSTRUCTION

SPECIAL FEATURE PRINTED WITH THE GREAT SEAL AND "UNITED STATES OF AMERICA" IN ONE COLOR METALLIC GOLD INK

UNIT QUANTITY FORM PACKAGE

NOTE TO CONTRACTING OFFICER: CONTACT THE ENGINEERING SECTION FOR A DIAGRAM OF THE FINISHED NAPKIN.

PACKAGING/PACKING: One thousand (1,000) cocktail napkins shall be packaged in accordance with normal commercial practice and packed to assure acceptance by common carrier and to provide product protection against loss or damage during multiple shipments, handling and storage. The shipping container shall be in compliance with the National Motor Freight Classification and the Uniform Freight Classification, and shall not be more than 51 pounds in weight.

UI: PG (One thousand (1,000) cocktail napkins per package)

NSN: 8540-00-262-7178

ITEM NAME TOWEL, PAPER DESIGN FORM SINGLE FOLD INTERLOCKED TO FACILITATE

DISPENSING ONE AT A TIME

MINIMUM SURFACE AREA 99.00 SQUARE INCHES (UNFOLDED)OVERALL FOLDED DEPTH 5.50 INCHES (+/- 0.5 INCH)OVERALL FOLDED WIDTH 9.25 INCHES (+/- 0.5 INCH)BASIS WEIGHT 22 TO 30 LBS (24 IN X 36 IN - 500 SHEETS) IAW

TAPPI T 410MINIMUM TENSILE STRENGTH 34 OZ/IN - IAW TAPPI T 404MINIMUM WATER ABSORPTION 70 SEC PER 0.1 ML - IAW TAPPI T 432FINISH STYLE UNIFORM FORMATION FINISH PROCESS CREPING OR EMBOSSINGUNIT PACKAGE QUANTITY 4,000 PAPER TOWELSUNIT PACKAGE TYPE BOX

PACKAGING: Towels may be bundled in quantities of two hundred (200) or two hundred and fifty (250) in accordance with normal commercial practice.

PACKING: Four thousand (4,000) paper towels shall be packaged in a box in accordance with normal commercial practice and packed to assure acceptance by common carrier and to provide product protection against loss or damage during multiple shipments, handling and storage. The

shipping container shall be in compliance with the National Motor Freight Classification and the Uniform Freight Classification, and shall not be more than 51 pounds in weight.

The contractor shall certify that the product offered shall include a range of 40 - 100% recovered fiber, including a range of 40 - 60 % postconsumer fiber in accordance with the EPA Comprehensive Procurement Guidelines, which may be found at:

www.epa.gov/epawaste/conserve/tools/cpg/index.htm

UI: BX (Four thousand (4,000) paper towels shall be packaged in a box)(Towels may be bundled in quantities of two hundred (200) or two hundred and fifty (250))

NSN: 8540-00-276-7569

ITEM NAME NAPKIN, TABLE, PAPEROVERALL UNFOLDED WIDTH 11.25 INCHESOVERALL UNFOLDED LENGTH 11.25 INCHESOVERALL SURFACE AREA 149.0 SQUARE INCHESMATERIAL PAPERNOMINAL BASIS WEIGHT 13 POUNDS (24 INCHES X 36 INCHES PER 500 SHEETS)FOLD TYPE QUARTER FOLDEDPLY TYPE SINGLEOVERALL FINISH PAPER SHALL BE CREPED OR EMBOSSEDUNIT PACKAGING FORM BOXUNIT PACKAGING QUANTITY 6,000 QUANTITY PER UNIT 6,000 NAPKINS PER BOX

CHARACTERISTIC REQUIREMENT TEST METHODBasis Weigh, min. g/m2(Lbs. 24 x 36-500)

20.3 g/m2 (12.5)

T410

Dry Tensile strengthMD, Kg/15 mm (oz/inch) min.CD, Kg/15 mm (oz/inch) min.

0.268 (16) 0.10 (5.9)

T 404 or T494

Absorption Time, sec., max. 100 T432Brightness, percent, min. 76 T 452

PACKAGING/PACKING: Six thousand (6,000) table paper napkins shall be packaged in accordance with normal commercial practice to assure acceptance by common carrier and to provide product protection against loss or damage during multiple shipments, handling and storage. The shipping container shall be in compliance with the National Motor Freight Classification and the Uniform Freight Classification, and shall not be more than 51 pounds in weight.

The contractor shall certify that the product offered shall include a minimum range of 30 - 100% recovered fiber, including 30 - 60 % postconsumer fiber in accordance with the EPA Comprehensive Procurement Guidelines, which may be found at:


http://www.epa.gov/epawaste/conserve/tools/cpg/index.htm


UI: BX (Six thousand (6,000) table paper napkins shall be packaged per box)

NSN: 8540-00-276-7570 ITEM NAME NAPKINS, TABLE, PAPER OVERALL WIDTH 16.00 INCHESOVERALL LENGTH 16.00 INCHESNOMINAL BASIS WEIGHT 10.50 POUNDS (24 IN. x 36 IN. PER 500 SHEETS) OVERALL SURFACE AREA 272.00 SQUARE INCHESNAPKIN TYPE DINNERPLY TYPE 3 PLYFOLD QUANTITY 8 FOLDSPECIAL FEATURE EMBOSSED

CHARACTERISTIC REQUIREMENT TEST METHODBasis Weigh, min. g/m2 (10.5) T 410(Lbs, 24 x 36-500) min

Absorption Time, sec., max 100 T 432

Brightness, percent, min 76 T 452

PACKAGING/PACKING: Two thousand (2,000) napkins shall be packaged in a box in accordance with normal commercial practice and packed to assure acceptance by common carrier and to provide product protection against loss or damage during multiple shipments, handling and storage. The shipping container shall be in compliance with the National Motor Freight Classification and the Uniform Freight Classification, and shall not be more than 51 pounds in weight.



UI: BX (Two thousand (2,000) napkins shall be packaged in a box

NSN: 8540-00-279-7777

ITEM NAME NAPKINS, TABLE, PAPER

OVERALL WIDTH 14.50 INCHESOVERALL LENGTH 14.50 INCHESOVERALL SURFACE AREA 217.0 SQUARE INCHESNOMINAL BASIS WEIGHT 20 POUNDS (24 INCHES X 36 INCHES PER 500 SHEETS) NAPKIN TYPE DINNER SIZEPLY TYPE 2NUMBER OF FOLDS EIGHT UNIT PACKAGING FORM BOXUNIT PACKAGING QUANTITY 3,000 NAPKINS PER BOX


PHYSICAL REQUIREMENT:

CHARACTERISTIC REQUIREMENT TEST METHOD

Basis Weigh, min. g/m2 32.6 g/m2 T410(Lbs, 24 x 36-500) min. (20)

Absorption Time, sec., max. 100 T 432

Brightness, percent, min. 76 T 452

PACKAGING/PACKING: Three thousand (3,000) table paper napkins shall be packaged in a box in accordance with normal commercial practice to assure acceptance by common carrier and to provide product protection against loss or damage during multiple shipments, handling and storage. The shipping container shall be in compliance with the National Motor Freight Classification and the Uniform Freight Classification, and shall not be more than 51 pounds in weight.



UI: BX (Three thousand (3,000) table paper napkins shall be packaged in a box)

NSN: 8540-00-281-8360

ITEM NAME TISSUE, FACIAL

OVERALL WIDTH 7.000 INCHES MINIMUM SURFACE AREA 66.00 SQUARE INCHESNOMINAL BASIS WEIGHT 19 POUNDS (24 INCHES X 36 INCHES PER 500 SHEETS)COLOR WHITEMATERIAL BLEACHED CHEMICAL FIBERPLY QUANTITY 2FOLD C-FOLDED OR MULTIFOLDUNIT PACKAGING FORM PACKAGEUNIT PACKAGE QUANTITY 200


QUANTITY PER UNIT 200 TISSUES PER PACKAGEUNIT OF ISSUE 6 PACKAGES PER BOX TENSILE STRENGTH DRY, CROSS DIRECTION (2 IN. GAGE LENGTH) - 4 OZF/IN.,

MIN.ABSORPTION TIME (0.01 ml. H2O/sec.) - 5 sec., max.


The facial tissue shall comply with Table I of ASTM D4369; Table A and the following characteristics.

The sizes for type II shall be as listed in Table A.

Table A Type Area Smaller dimension inches (min.) fold II 66.0 7.0 Supplier's option

NOTE. If creases or the finished size of the tissues make it impossible to prepare specimens of the required size from the tissues, tests shall be performed on the large roll of paper, before cutting and packaging.

PACKAGING/PACKING: One thousand two hundred (1,200) facial tissues shall be packaged in accordance with normal commercial practice and packed to assure acceptance by common carrier and to provide product protection against loss or damage during multiple shipments, handling and storage. The shipping container shall be in compliance with the National Motor Freight Classification and the Uniform Freight Classification, and shall not be more than 51 pounds in weight.

The contractor shall certify that the product offered shall include a range of 10 - 100 % recovered fiber, including a range of 10 - 15 % postconsumer fiber in accordance with the EPA Comprehensive Procurement Guidelines, which may be found at:


UI: PG (thousand two hundred (1,200) facial tissues per package)

NSN: 8540-00-285-7001

ITEM NAME NAPKIN, TABLE, PAPER

OVERALL UNFOLDED WIDTH 9.875 INCHESOVERALL UNFOLDED LENGTH 9.875 INCHESOVERALL FOLDED WIDTH 3.375 INCHES MINIMUM TO 3.625 INCHES MAXIMUM OVERALL FOLDED LENGTH 6.625 INCHES MINIMUM TO 6.875 INCHES MAXIMUM OVERALL SURFACE AREA 130.0 SQUARE INCHESMATERIAL PAPERCOLOR WHITEOVERALL FINISH PAPER SHALL BE CREPED OR EMBOSSEDPLY SINGLE


DISPENSER TYPE SENIORUNIT PACKAGING FORM BOXUNIT PACKAGE QUANTITY 10,000 TISSUES PER PACKAGE


Basis Weigh, min. g/m2(Lbs. 24 x 36-500)

20.3 g/m2 (12.5)

T410


0.268 (16) 0.10 (5.9)

T 404 or T494


PACKAGING/PACKING: Ten thousand (10,000) table paper napkins shall be packaged in accordance with normal commercial practice to assure acceptance by common carrier and to provide product protection against loss or damage during multiple shipments, handling and storage. The shipping container shall be in compliance with the National Motor Freight Classification and the Uniform Freight Classification, and shall not be more than 51 pounds in weight.



UI: BX (Ten thousand (10,000) table paper napkins per box)

NSN: 8540-00-291-0389 ITEM NAME TOWEL, PAPER

OVERALL WIDTH 9.200 INCHES (+/- 0.500 INCHES)OVERALL FOLD DEPTH 3.125 INCHES (+/- 0.125 INCHES)OVERALL SURFACE AREA 85.00 SQUARE INCHESDESIGN FORM MULTI-FOLDCOLOR NATURALNOMINAL BASIS WEIGHT 22 TO 30 LBS (24 INCHES X 34 INCHES PER 500 SHEETS)OVERALL FINISH FINISH TOWEL SHALL HAVE A UNIFORM FORMATION AND

SHALL BE CREPED OR EMBOSSEDUSAGE FORM SHEETUNIT PACKAGING FORM BOX UNIT PACKAGING QUANTITY 4,000 QUANTITY PER UNIT 4,000 SHEETS PER BOX

PHYSICAL REQUIREMENT

TAPPI TEST METHOD (T410) TYPE II 40-49 (25-30)


TAPPI TEST METHOD (T404) TENSILE STRENGTH, AVERAGE OF BOTH DIRECTIONS, MIN. DRY, N/M (OZ/INCH) 458 (42)

TAPPI TEST METHOD (T432) WATER ABSORPTION 0.1 ML, SEC., MAX 100

PACKAGING/PACKING: Four thousand (4,000) paper towels shall be packaged in a snug fitting fiberboard box in accordance with normal commercial practice and packed to assure acceptance by common carrier and to provide product protection against loss or damage during multiple shipments, handling and storage. The shipping container shall be in compliance with the National Motor Freight Classification and the Uniform Freight Classification, and shall not be more than 51 pounds in weight.



UI: BX (Four thousand (4,000) paper towels shall be packaged per box)

NSN: 8540-00-291-0392

ITEM NAME TOWEL, PAPEROVERALL WIDTH 10.25 INCHES OVERALL FOLD DEPTH 4.000 INCHES OVERALL SURFACE AREA 130.0 SQUARE INCHESMATERIAL PAPERCOLOR NATURALDESIGN FORM C-FOLD NOMINAL BASIS WEIGHT 22 TO 30 LBS (24 INCHES X 36 INCHES PER 500 SHEETS)SPECIAL FEATURE COMPATIBLE FOR USE WITH GSA DISPENSER

NSN 4510-00-585-6305 UNIT PACKAGING FORM BOXUNIT PACKAGING QUANTITY 200 TOWELS PER BUNDLEQUANTITY PER UNIT 12 BUNDLES PER BOX

PHYSICAL REQUIREMENTS.

Characteristic Requirement Tappi Test Method

Water absorption 0.1 ml, 100 sec T432seconds (max)

Tensile strength I/N/100 mm (oz/in), avg. of both directions (min) Dry 29.4 (27) T494Wet 8.7 (8) T456


PACKAGING/PACKING: Two thousand four hundred (2,400) paper towels shall be packaged in accordance with normal commercial practice to assure acceptance by common carrier and to provide product protection against loss or damage during multiple shipments, handling and storage. The shipping container shall be in compliance with the National Motor Freight Classification and the Uniform Freight Classification, and shall not be more than 51 pounds in weight.



UI: BX (Two thousand four hundred (2,400) paper towels shall be packaged in a box)

NSN: 8540-00-793-5425

ITEM NAME TISSUE, FACIAL

OVERALL WIDTH 7.000 INCHESOVERALL SURFACE AREA 66.00 SQUARE INCHESNOMINAL BASIS WEIGHT 19 POUNDS (24 INCHES X 36 INCHES PER 500 SHEETS) PLY QUANTITY 2COLOR WHITEMATERIAL BLEACHED CHEMICAL FIBER DESIGN FORM C-FOLDED OR MULTIFOLDEDTENSILE STRENGTH DRY, CROSS DIRECTION (2 IN. GAGE LENGTH) 4 OZF/IN.,

MIN.ABSORPTION TIME (0.01 ml. H2O/sec.) - 5 sec., max.UNIT PACKAGING QUANTITY 1,200 TISSUES PER PACKAGE


The facial tissue shall comply with Table I of ASTM D4369; Table A and the following characteristics.

Table AType Area Smaller dimension inches (min.) Fold II 66.0 7.0 Supplier's option

The tissues shall be individually cut and, as specified above. If other than the interfold is selected, then the open side of the tissue shall be facing towards the dispenser's opening such that the end of the tissue can be used to pull it out of the dispenser. If interfold is required, the tissue dispenses a portion of the following tissue.

NOTE. If creases or the finished size of the tissues, make it impossible to prepare specimens of the required size from the tissues, tests shall be performed on the large roll of paper, before cutting and packaging.


PACKAGING/PACKING: One thousand two hundred (1,200) facial tissues shall be packaged in accordance with normal commercial practice and packed to assure acceptance by common carrier and to provide product protection against loss or damage during multiple shipments, handling and storage. The shipping container shall be in compliance with the National Motor Freight Classification and the Uniform Freight Classification, and shall not be more than 51 pounds in weight.



UI: PG (One thousand two hundred (1,200) facial tissues per package)

NSN: 8540-00-965-4691

ITEM NAME NAPKIN, TABLE, PAPER

OVERALL UNFOLDED WIDTH 7.0000 INCHESOVERALL UNFOLDED LENGTH 13.875 INCHESFOLDED WIDTH 3.3750 INCHES MINIMUM TO 3.6250 INCHES MAXIMUMFOLDED LENGTH 6.6250 INCHES MINIMUM TO 6.8750 INCHES MAXIMUM OVERALL SURFACE AREA 94.500 SQUARE INCHESOVERALL FINISH FINISHED PAPER SHALL BE CREPED OR EMBOSSEDMATERIAL PAPERDISPENSER TYPE JUNIORPLY QUANTITY SINGLEFOLD TYPE DISPENSERUNIT PACKAGING FORM BOXUNIT PACKAGING QUANTITY 10,000QUANTITY PER UNIT 10,000 NAPKINS PER BOX

CHARACTERISTIC REQUIREMENT TEST METHODBasis Weigh, min. g/m2(Lbs. 24 x 36-500)

20.3 g/m2 (12.5)

T410


0.268 (16) 0.10 (5.9)

T 404 or T494


PACKAGING/PACKING: Ten thousand (10,000) napkins shall be packaged in accordance with normal commercial practice to assure acceptance by common carrier and to provide product protection against loss or damage during multiple shipments, handling and storage. The shipping


container shall be in compliance with the National Motor Freight Classification and the Uniform Freight Classification, and shall not be more than 51 pounds in weight.



UI: BX (Ten thousand (10,000) napkins shall be packaged per box)

NSN: 8540-00-965-5790 ITEM NAME COVER, TOILET SEAT, DISPOSABLE

OVERALL OPENED WIDTH 14.75 INCHES (+/- 0.50 INCH)OVERALL OPENED LENGTH 17.25 INCHES (+/- 0.50 INCH)OVERALL CENTER TEAR OUT WIDTH 6.000 INCHES (+/- 0.50 INCH)OVERALL CENTER TEAR OUT LENGTH 10.75 INCHES (+/- 0.50 INCH)OVERALL FOLDED COVER WIDTH 7.000 INCHES (+/- 0.50 INCH)OVERALL FOLDED COVER LENGTH 10.00 INCHES (+/- 0.50 INCH)FOLD TYPE QUARTER FOLDEDCOLOR WHITE

SPECIAL FEATURES - the seat covers shall fit and feed satisfactorily from a Rochester Midland dispenser model no. 25131500 or a James River dispenser model no. 726 or a Protecto Model no. Vanguard 9270.

The contractor shall certify that product meets the salient characteristics of this descriptions. The toilet seat covers shall not clog or interfere with the water flow of waste lines or septic tank systems, and that it shall be nontoxic and harmless to humans.

The disposable paper seat covers shall be an unsized tissue and shall contain no wet-strength additives.

BLEACHING -To obtain an acceptable brightness, in accordance with the performance standards of this document, a chemical bleaching process may be used. When specified in the ordering data, the bleaching process shall not include the use of chlorine, chlorine dioxide, or other chlorine compounds. The government reserves the right to require proof of such conformance prior to first delivery and thereafter as may be otherwise provided for under the provisions of the contract.

PHYSICAL REQUIREMENT.


BASIS WEIGHT 15 G/M2, MIN.(9.1 LB. (24X36-500)), MIN) T410 INTERNAL TEARING RESISTANCE MD 8 G, MIN CD 10 G, MIN T414BURSTING STRENGTH 4.0 PSI, MIN. T403BRIGHTNESS 70 PERCENT, MIN. T452


PACKAGING/PACKING: Two hundred fifty (250) covers shall be packaged in accordance with normal commercial practice and packed to assure acceptance by common carrier and to provide product protection against loss or damage during multiple shipments, handling and storage. The shipping container shall be in compliance with the National Freight Classification and the Uniform Freight Classification, and shall not be more than 51 pounds in weight.

UI: PG (Two hundred fifty (250) covers per package)

NSN: 8540-01-055-6094

ITEM NAME PAPER, TOILETIAW A-A-697

TYPE 1OVERALL WIDTH 4.5000 INCHESOVERALL ROLL LENGTH 4375.0 INCHES OVERALL OUTSIDE DIAMETER 4.5000 INCHES (+/- 0.1250 INCHES)OVERALL CORE DIAMETER 1.3750 INCHES MINIMUM TO 1.7500 INCHES MAXIMUMPERFORATION INTERVAL 4.2500 INCHES MINIMUM TO 4.6250 INCHES MAXIMUM MATERIAL FIBROUS, CELLULOSIC MATERIALPLY QUANTITY 1 NOMINAL BASIS WEIGHT 11 POUNDS (24 INCHES X 36 INCHES PER 500 SHEETS) USAGE FORM ROLL UNIT PACKAGING QUANTITY 48 ROLLS PER BOX

PHYSICAL REQUIREMENTS:

2 Salient Characteristic. Toilet tissues shall be wound evenly on a round paperboard core, made from fibrous, cellulosic material and meet the requirements of Table 1, below.

Table 1Characteristic Type 1 TAPPI

Basis Weight, g/m2, min(24 x 36-500), min.

17.9(11 lb)

T410

Tensile Strength, Dry CD 50mm (2 in.), min.

44 N/m4.0 ozf/in

T494

Absorption Time, 0.01 ml H2O, max

35 sec T432

Brightness, avg. both sides, min.

65 percent T452

Inside dia. of core 34.925 - 44.45 mm (1 3/8 - 1 3/4")

Roll width 114.3 +/- 3.175 mm (4 1/2 +/- 1/8")

Roll outside diameter 114.3 +/- 3.175 mm (4 1/2 +/- 1/8")

Perforation interval 107.95 - 117.475 mm (4 1/4 - 4 5/8")

Average roll length, min. 114,300 mm

(4,500") Length per roll, min. 11,125 mm

(4,375")

2.1 Bleaching: To obtain an acceptable brightness, a chemical bleaching process may be used. When specified, the bleaching process shall not include the use of chlorine, chlorine dioxide, or hypochlorite. Certification of compliance shall be made available upon request by the Government.

2.2 Workmanship. For Types 1 toilet tissues shall be clean and free from dirt spots, holes, or tears 1/16 inch or larger, or more than 5 dirt spots, holes, or tears less than 1/16 inch in one sheet; shives or slivers 1/8 inch or more in length, or more than five shives or slivers less than 1/8 inch in length in one sheet; any foreign matter, undigested paper, or unbleached waste. Toilet tissue shall be uniform in color and shall be trimmed with clean, smooth edges. Sheet formation shall be uniform. Clumps of undispersed fibers or thin looking areas is evidence of poor formation. The tissues shall be perforated so that the sheets can be evenly and completely separated.

2.3 Certification Clause. The supplier shall certify that the toilet tissue shall not clog or interfere with the water flow of waste lines or septic tank systems, and that it shall be nontoxic and harmless to humans. PACKAGING/PACKING: Forty eight (48) toilet paper rolls shall be packaged in accordance with normal commercial practice to assure acceptance by common carrier and to provide product protection against loss or damage during multiple shipments, handling and storage. The shipping container shall be in compliance with the National Motor Freight Classification and the Uniform Freight Classification, and shall not be more than 51 pounds in weight.

NOTICE: Packaging and packing requirements in this item purchase description are unique at the request of the U.S. Navy Supply Systems Command. This item is included in the Navy’s PLASTICS REMOVAL IN MARINE ENVIRONMENT (PRIME) PROGRAM under the U.S. Marine Plastic Pollution Research and Control Act of 1987 (MPPRCA) and the International Convention for the Prevention of Pollution from Ships Treaty (MARPOL) Annex V. Items in the PRIME program require biodegradable packing materials. The statement "PLASTIC PACKING MATERIALS AND PRESSURE SENSITIVE TAPES ARE PROHIBITED" is included in the packaging and packing requirements for all PRIME program items.

PREPARATION FOR DELIVERY: The item(s) shall be packaged and packed in accordance with the latest revision of ASTM D 3951, Standard Practice for Commercial Packaging. PLASTIC PACKING MATERIALS AND PRESSURE SENSITIVE TAPES ARE PROHIBITED. Copies of ASTM standards are available from the American Society for Testing and Materials, 100 Barr Harbor Drive, West Conshohocken, PA 19428-2959. Phone: 610-832-9585, Fax: 610-832-9555, Web site: www.astm.org, e-mail: [email protected].




mailto:[email protected]

UI: BX: ( Forty eight (48) toilet paper rolls shall be packaged per box)

NSN: 8540-01-055-6134

ITEM NAME TOWEL, PAPEROVERALL WIDTH 9.250 INCHES (+/- 0.500 INCHES)OVERALL FOLD DEPTH 5.500 INCHES (+/- 0.500 INCHES)OVERALL SURFACE AREA 99.00 SQUARE INCHES (+/- 3 PERCENT)MATERIAL PAPER, UNBLEACHED COLOR KRAFTDESIGN FORM SINGLEFOLD NOMINAL BASIS WEIGHT 25 TO 30 POUNDS (24 INCHES X 36 INCHES PER 500

SHEETS)UNIT PACKAGING FORM BOXUNIT PACKAGING QUANTITY 250 TOWELS PER PACKAGEQUANTITY PER UNIT 16 PACKAGES PER BOX

PACKAGING/PACKING: Sixteen (16) packages of paper towels (totaling 4,000 towels) shall be packed in a close-fitting box conforming to ASTM D5118/D5118M, Type CF, single wall, Style RSC, Class Weather Resistant, Grade V3c or W5c. The box shall be closed in accordance with method B of ASTM D1974. Closing and sealing tape shall be 2 inches wide conforming to ASTM D5486/D5486M, Type V. Plastic packaging, bundling, palletizing, and associated marking materials are prohibited. The shipping container shall be in compliance with the National Motor Freight Classification and the Uniform Freight Classification, and shall not be more than 51 pounds in weight.

NOTICE: Packaging and packing requirements in this item purchase description are unique at the request of the U.S. Navy Supply Systems Command. This item is included in the Navy’s PLASTICS REMOVAL IN MARINE ENVIRONMENT (PRIME) PROGRAM under the U.S. Marine Plastic Pollution Research and Control Act of 1987 (MPPRCA) and the International Convention for the Prevention of Pollution from Ships Treaty (MARPOL) Annex V. Items in the PRIME program require biodegradable packing materials. The statement "PLASTIC PACKING MATERIALS AND PRESSURE SENSITIVE TAPES ARE PROHIBITED" is included in the packaging and packing requirements for all PRIME program items.






UI: BX (PACKAGING/PACKING: (Sixteen (16) packages of paper towels (totaling 4,000 towels) shall be packed in a close-fitting box)

NSN: 8540-01-056-2897 ITEM NAME NAPKIN, TABLE, PAPER

OVERALL UNFOLDED WIDTH 9.875 INCHESOVERALL UNFOLDED LENGTH 9.875 INCHESOVERALL FOLDED WIDTH 3.375 INCHES MINIMUM TO 3.625 INCHES MAXIMUM OVERALL FOLDED LENGTH 6.625 INCHES MINIMUM TO 6.875 INCHES MAXIMUMOVERALL SURFACE AREA 130.0 SQUARE INCHESMATERIAL PAPERNAPKIN TYPE SENIOR DISPENSER NAPKINNOMINAL BASIS WEIGHT 12.50 POUNDS (24 INCHES X 36 INCHES PER 500 SHEETS)PLY TYPE SINGLEDISPENSER TYPE SENIORPULP TYPE WOOD FIBERFOLD TYPE DISPENSERUNIT PACKAGING FORM BOXUNIT PACKAGING QUANTITY 10,000QUANTITY PER UNIT 10,000 NAPKINS PER BOX

PHYSICAL REQUIREMENT: CHARACTERISTIC REQUIREMENT TEST METHOD

Basis Weigh, min. g/m2(Lbs. 24 x 36-500)

20.3 g/m2 (12.5)

T410


0.268 (16) 0.10 (5.9)

T 404 or T494


PACKAGING/PACKING: Ten thousand (10,000) napkins shall be packaged in accordance with normal commercial practice to assure acceptance by common carrier and to provide product protection against loss or damage during multiple shipments, handling and storage. The shipping container shall be in compliance with the National Motor Freight Classification and the Uniform Freight Classification, and shall not be more than 51 pounds in weight.

NOTICE: Packaging and packing requirements in this item purchase description are unique at the request of the U.S. Navy Supply Systems Command. This item is included in the Navy’s PLASTICS REMOVAL IN MARINE ENVIRONMENT (PRIME) PROGRAM under the U.S. Marine Plastic Pollution Research and Control Act of 1987 (MPPRCA) and the International Convention for the Prevention of Pollution from Ships Treaty (MARPOL) Annex V. Items in the PRIME program require biodegradable packing materials. The statement "PLASTIC PACKING MATERIALS AND PRESSURE SENSITIVE

TAPES ARE PROHIBITED" is included in the packaging and packing requirements for all PRIME program items.


The contractor shall certify that the product offered shall include minimum range of 30 - 100% recovered fiber, including 30 - 60 % postconsumer fiber in accordance with the EPA Comprehensive Procurement Guidelines, which may be found at:


UI: BX (Ten thousand (10,000) napkins shall be packaged in per box)

NSN: 8540-01-359-0764 ITEM NAME PAPER, TOILET

IAW A-A-697

OVERALL WIDTH 4.5000 INCHESOVERALL LENGTH 4500.0 INCHESOVERALL INSIDE CORE DIAMETER 1.375 INCHES TO 1.750 INCHESPERFORATION INTERVAL 4.250 TO 4.625 INCHES MATERIAL FIBROUS, CELLULOSIC MATERIAL (UNBLEACHED)COLOR WHITEPLY QUANTITY 1NOMINAL BASIS WEIGHT 10 POUNDS (24 INCHES X 36 INCHES PER 500

SHEETS)UNIT PACKAGING FORM ROLL UNIT PACKAGE QUANTITY 96 ROLLS PER BOX

PACKAGING/PACKING: Ninety-six (96) rolls of toilet paper shall be packaged in accordance with normal commercial practice and packed to assure acceptance by common carrier and to provide product protection against loss or damage during multiple shipments, handling and storage. The shipping container shall be in compliance with the National Motor Freight Classification and the Uniform Freight Classification, and shall not be more than 51 pounds in weight.



UI: BX (Ninety-six (96) rolls of toilet paper shall be packaged per box)




NSN: 8540-01-359-0798

ITEM NAME TOWEL, PAPER

OVERALL WIDTH 9.250 INCHES (+/- 0.500 INCHES)OVERALL FOLD DEPTH 5.500 INCHES (+/- 0.500 INCHES)MATERIAL PAPER OVERALL, UNBLEACHEDOVERALL BASIS WEIGHT 25 TO 30 LBS (24 INCHES X 36 INCHES PER 500 SHEETS)OVERALL AREA 99 SQUARE INCH (+/- 3.000 PERCENT, MIN. SURFACE

AREA)OVERALL FINISH CREPING OR EMBOSSINGSPECIAL FEATURE 100 PERCENT WASTE PAPER INCLUDING A MINIMUM OF 90

PERCENT POST-CONSUMER RECOVERED MATERIALSUNIT PACKAGING FORM BOXUNIT PACKAGING QUANTITY 4,000 PER BOX

PACKAGING/PACKING: Four thousand (4,000) paper towels shall be packaged in a box in accordance with normal commercial practice and packed to assure acceptance by common carrier and to provide product protection against loss or damage during multiple shipments, handling and storage. The shipping container shall be in compliance with the National Motor Freight Classification and the Uniform Freight Classification, and shall not be more than 51 pounds in weight.

UI: BX (Four thousand (4,000) paper towels shall be packaged in a box)

NSN: 8540-01-378-1315


OVERALL WIDTH 8.000 INCHESOVERALL LENGTH 800.0 FEET PERFORATION TYPE NON-PERFORATEDCOLOR WHITEUSAGE FORM BOXUNIT PACKAGING FORM 12 ROLLS PER BOX

PHYSICAL PROPERTIES


Water Capacity (g/4 x4 ) 1.0 T432

Water Wicking MD (cm/15 seconds) 1.0

Caliper, single sheet (.000 in) 8.7

Tensile Strength MD Wet (g/3 in.) 1900 T494

Tensile Strength MD Dry (g/3 in.) 5900 T456Tensile Strength CD Wet (g/3 in.) 850Tensile Strength CD Dry (g/3 in.) 2900MD Stretch (%) 9.0

PACKAGING/PACKING: Twelve (12) paper towel rolls shall be packaged in accordance with normal commercial practice and packed to assure acceptance by common carrier and to provide product protection against loss or damage during multiple shipments, handling and storage. The shipping container shall be in compliance with the National Motor Freight Classification and the Uniform Freight Classification, and shall not be more than 51 pounds in weight.



UI: BX (Twelve (12) paper towel rolls shall be packaged in a box)

8540-01-378-5292

ITEM NAME: PAPER, TOILET

OVERALL WIDTH 0003.650 INCHESOVERALL LENGTH 1000.000 FEETOVERALL DIAMETER 0009.000 INCHESNOMINAL BASIS WEIGHT 0017.000 POUNDSCOLOR WHITE OVERALLMATERIAL PAPER, TOILET TISSUEPLY TWO PLYUSAGE FORM ROLLUNIT PACKAGING FORM BOXUNIT PACKAGE QUANTITY TWELVE (12) ROLLS PER BOX

PACKAGING/PACKING: Twelve (12) rolls of toilet paper shall be packaged in a box in accordance with normal commercial practice and packed to assure acceptance by common carrier and to provide product protection against loss or damage during multiple shipments, handling and storage. The shipping container shall be in compliance with the National Motor Freight Classification and the Uniform Freight Classification, and shall not be more than 51 pounds in weight.



UI: BX (Twelve (12) rolls of toilet paper shall be packaged in a box)



NSN: 8540-01-378-6218

ITEM NAME PAPER, TOILETOVERALL ROLL WIDTH 3.500 INCHES OVERALL ROLL LENGTH 4,000 FEETPLY SINGLE / 1 PLYPERFORATION NON PERFORATEDUSAGE FORM ROLLROLL SIZE JUMBOCOLOR WHITESAMPLING TEST METHOD I.A.W. TAPPI T400 - COMMERCIAL ITEM DESCRIPTION UNIT PACKAGING QUANTITY 6 ROLLS SHEETS PER BOX


Basis Weigh, min. g/m2 17.9 g/m2 T 410(lbs, 24 x 36-500), min (11)

Tensile strength, Dry CD 44 N/m T 494, 50mm (2 in), min 4.0 ozf/in

Absorption Time, 0.01 ml H20, max 3 5 sec

Brightness, avg. both sides, min. 65% T 452

PACKAGING/PACKING: Six (6) toilet paper rolls per box shall be packaged in accordance with normal commercial practice and packed to assure acceptance by common carrier and to provide product protection against loss or damage during multiple shipments, handling and storage. The shipping container shall be in compliance with the National Motor Freight Classification and the Uniform Freight Classification, and shall not be more than 51 pounds in weight.



UI: BX (Six (6) toilet paper rolls per box)NSN: 8540-01-380-0690

ITEM NAME PAPER, TOILET

OVERALL SHEET WIDTH 4.00 INCHESOVERALL SHEET LENGTH 4.00 INCHESSHEET PERFORATION INTERVAL 4.250 INCHES - 4.375 INCHESOVERALL ROLL LENGTH 2,200 INCHES, WRAPPED AROUND A CORENUMBER OF SHEETS PER ROLL 550 SHEETSMATERIAL FIBROUS, CELLULOSIC MATERIALUSAGE FORM ROLL, INDIVIDUALLY WRAPPED, UNCOMPRESSED


ROLL SIZE JUMBOUNIT PACKAGING QUANTITY 80 ROLLS PER BOX

PHYSICAL REQUIREMENTS


Basis Weigh, min. g/m2 17.9 g/m2 T 410(lbs, 24 x 36-500), min (11)


Absorption Time, 0.01 ml H20, max. 35 sec

Brightness, avg. both sides, min. 65% T 452

TEST METHOD I.A.W. TAPPI T400 - COMMERCIAL ITEM DESCRIPTION

PACKAGING/PACKING: Eighty (80) toilet paper rolls shall be packaged in accordance with normal commercial practice and packed to assure acceptance by common carrier and to provide product protection against loss or damage during multiple shipments, handling and storage. The shipping container shall be in compliance with the National Motor Freight Classification and the Uniform Freight Classification, and shall not be more than 51 pounds in weight.



UI: BX (Eighty (80) toilet paper rolls shall be packaged per box)

NSN: 8540-01-462-5333


OVERALL ROLL WIDTH 7.875 INCHESOVERALL ROLL LENGTH 400 FEETCORE INCLUDEDUSER FORM ROLL COLOR NATURALUNIT PACKAGING QUANTITY 12 ROLLS PER BOX



PHYSICAL PROPERTY DATA IS AS PRODUCED; SUBSEQUENT STORAGE CONDITIONS AND THE AGE OF THE PRODUCT, THAT MAY AFFECT THE PROPERTIES OF THE PRODUCT AS RECEIVED. TEST RESULTS OF COMPETITIVE PRODUCT ARE SINGLE SAMPLE OF THE PRODUCT PROVIDED BY THE CUSTOMER.

CHARACTERISTIC REQUIREMENT TEST METHODWATER CAPACITY (G/4 X4 ) 1.0 T 432WATER WICKING MD (CM/15 SECONDS) 1.0CALIPER, SINGLE SHEET .000 IN) 8.7TENSILE STRENGTH MD WET (G/3 IN.) 1900 T 494TENSILE STRENGTH MD DRY (G/3 IN.) 5900 T 456TENSILE STRENGTH CD WET (G/3 IN.) 850TENSILE STRENGTH CD DRY (G/3 IN.) 2900MD STRETCH (PERCENT) 9.0

PACKAGING/PACKING: Twelve (12) rolls of paper towels shall be packaged in accordance with normal commercial practice and packed to assure acceptance by common carrier and to provide product protection against loss or damage during multiple shipments, handling and storage. The shipping container shall be in compliance with the National Motor Freight Classification and the Uniform Freight Classification, and shall not be more than 51 pounds in weight.



UI: BX (Twelve (12) rolls of paper towels shall be packaged per box)

NSN: 8540-01-494-0909


NOMINAL WIDTH 10.25 INCHES NOMINAL FOLD DEPTH 4.00 INCHES BASIS WEIGHT 25 TO 30 POUNDS (24 INCHES X 36 INCHES PER 500 SHEETS)DESIGN FORM C-FOLDMATERIAL PAPER


COLOR WHITESPECIAL FEATURE CHLORINE - FREEFOR USE WITH GSA DISPENSER NSN 4510-00-585-6305 UNIT PACKAGING FORM BOXUNIT PACKAGING QUANTITY 200 TOWELS PER BUNDLEUNIT PACKING QUANTITY 12 BUNDLES PER BOX (TOTAL 2,400 TOWELS)


CHARACTERISTIC REQUIREMENT TAPPI TEST METHOD

Water absorption 0.1 ml, seconds (max) 100 sec T432

Tensile strength I/N/100 mm (oz/in), avg. of both directions (min) Dry 29.4 (27) T494Wet 8.7 (8) T456 PACKAGING/PACKING: Twelve (12) bundles (totaling 2,400 towels) of paper towels shall be packaged in a box in accordance with normal commercial practice and packed to assure acceptance by common carrier and to provide product protection against loss or damage during multiple shipments, handling and storage. The shipping container shall be in compliance with the National Motor Freight Classification and the Uniform Freight Classification, and shall not be more than 51 pounds in weight.



UI: BX (Twelve (12) bundles (totaling 2,400 towels) of paper towels shall be packaged in a box)

NSN: 8540-01-494-0911

ITEM NAME TOWEL, PAPER OVERALL WIDTH 9.250 INCHES OVERALL FOLD DEPTH 5.375 INCHES DESIGN FORM SINGLE FOLD, UNBLEACHEDMATERIAL PAPERCOLOR KRAFT


BASIS WEIGHT 25 TO 30 POUNDS (24 INCHES X 36 INCHES PER 500 SHEETS)

UNIT PACKAGING FORM BOXUNIT PACKAGING QUANTITY 250 TOWELS PER BUNDLEUNIT PACKING QUANTITY 16 BUNDLES PER BOX (TOTAL 4,000 TOWELS)




Tensile strength I/N/100 mm (oz/in), avg. of both directions (min) Dry 29.4 (27) T494Wet 8.7 (8) T456

PACKAGING/PACKING: Sixteen (16) bundles (totaling 4,000 towels) of paper towels shall be packaged in a box in accordance with normal commercial practice and packed to assure acceptance by common carrier and to provide product protection against loss or damage during multiple shipments, handling and storage. The shipping container shall be in compliance with the National Motor Freight Classification and the Uniform Freight Classification, and shall not be more than 51 pounds in weight.



UI: BX (Sixteen (16) bundles (totaling 4,000 towels) of paper towels shall be packaged in a box)

NSN: 8540-01-494-1900


OVERALL WIDTH 10.25 INCHES OVERALL FOLD DEPTH 4.000 INCHES OVERALL SURFACE AREA 130.0 SQUARE INCHESMATERIAL PAPER, CHLORINE-FREE


COLOR WHITEDESIGN FORM C-FOLDPLY QUANTITY 1NOMINAL BASIS WEIGHT 25 TO 30 LBS (24 INCHES X 36 INCHES PER 500 SHEETS)SPECIAL FEATURE COMPATIBLE FOR USE WITH GSA DISPENSER NSN 4510-00-585-6305 UNIT PACKAGING FORM BOXUNIT PACKAGE QUANTITY 200 TOWELS PER BOX TOTALING 1400 TOWELSQUANTITY PER UNIT 7 PACKAGES PER BOX




Tensile strength I/N/100 mm (oz/in), avg. of both directions (min) Dry 29.4 (27) T494Wet 8.7 (8) T456 PACKAGING/PACKING: Seven (7) boxes of paper towels (totaling 1,400) paper towels per box shall be packaged in accordance with normal commercial practice and packed to assure acceptance by common carrier and to provide product protection against loss or damage during multiple shipments, handling and storage. The shipping container shall be in compliance with the National Motor Freight Classification and the Uniform Freight Classification, and shall not be more than 51 pounds in weight.



UI: BX (Seven (7) boxes of paper towels (totaling 1,400) paper towels per box shall be packaged per box)

NSN: 8540-01-554-7678


OVERALL PERFORATED WIDTH 4.000 INCHESOVERALL PERFORATED LENGTH 4.000 INCHESOVERALL LENGTH 2200.0 INCHES


PLY QUANTITY 2 MATERIAL FIBROUS, CELLULOSIC MATERIAL (CHLORINE-FREE)USAGE FORM ROLLROLL SIZE JUMBOPERFORATION TYPE PERFORATED SINGLE SHEET WOUND AROUND A CORETEST METHOD I.A.W. TAPPI T400 - COMMERCIAL ITEM DESCRIPTION UNIT PACKAGING FORM BOXUNIT PACKAGING QUANTITY 500 SHEETS PER ROLL

40 ROLLS PER BOX



Basis Weigh, min. g/m2 17.9 g/m2 T 410(lbs, 24 x 36-500), min (17 lb)


Absorption Time, 0.01 ml H20, max. 5 sec

Brightness, avg. both sides, min. 65 PERCENT T 452

PACKAGING/PACKING: Forty (40) rolls of toilet paper shall be packed in a close-fitting fiberboard box to insure delivery at destination, to provide for redistribution by the initial receiving activity, and shall be acceptable by common carrier under National Motor Freight Classification and Uniform Freight Classification, and shall not be more than 51 pounds in weight.The contractor shall certify that the product offered shall include a range of 20 - 100 % recovered fiber, including a range of 20 - 60 % postconsumer fiber in accordance with the EPA Comprehensive Procurement Guidelines, which may be found at:


UI: BX ((40) rolls of toilet paper shall be packed in a close-fitting fiberboard box)

NSN: 8540-01-590-9068


OVERALL WIDTH 3.7000 INCHES (+/- 0.125 INCHES) OVERALL LENGTH 2000.0 INCHES OVERALL OUTSIDE DIAMETER 12.000 INCHESOVERALL INSIDE CORE DIAMETER 3.3000 INCHES MATERIAL FIBROUS, CELLULOSIC MATERIAL (CHLORINE-FREE)


COLOR WHITEPLY QUANTITY 2ROLL SIZE JUMBO USAGE FORM ROLLUNIT PACKAGING QUANTITY 6 ROLLS PER BOX


The paper shall be wound evenly on a round paper board, made from fibrous, cellulosic material and specified the requirement of Table 1 below.


The paper shall be wound evenly on a round paper board, made from fibrous, cellulosic material and specified the requirement of Table 1 below.

TABLE I Physical Requirements________________________________________________________________________________CHARACTERISTIC REQUIREMENT TAPPI________________________________________________________________________________Basis Weight per ply (24 x 36 -500) Grammage, g/m2 (pounds) Min 8.5 T410________________________________________________________________________________Water absorption 0.1ml, Seconds (max) 5 seconds T432 ________________________________________________________________________________Tensile strength, dry CD, grams 150(1 ) per ply, min/target/max 250 N/A T494________________________________________________________________________________Tensile strength, dry MD, grams 300(1 ) per ply, min/target/max 350

400 T494________________________________________________________________________________Brightness, percentAverage both sides, min 76 PERCENT T452________________________________________________________________________________Stretch target + or -2 PERCENT 10 ________________________________________________________________________________Moisture, target + or -1 PERCENT 6________________________________________________________________________________Caliper, 8 plies, inches .027-.030________________________________________________________________________________Red Lines/ Paper Breaks: No more than two per parent roll, none within 6 inches of the core, and none within 4 inches from the outside edge. No more than 25 percent of a shipment may contain red lines________________________________________________________________________________*Before Tappi T432 is performed the paper should be conditioned according to Tappi T402.

ODOR. Tissue shall have no disagreeable odor when dry or wet. To test for odor when wet, soak a single tissue in distilled water at room temperature for 2 minutes. Remove the tissue from the water and smell the tissue at a distance of 304 610 mm (12 -24 inches). Any disagreeable odor shall be cause for rejection. Supplier shall certify that the tissue shall not clog or interfere with the water flow of waste lines or septic systems.

BLEACHING. To obtain an acceptable brightness, a chemical bleaching process may be used. Only when specified, the bleaching process shall not include the use of chlorine, chlorine dioxide, or hypochlorite. Certification of compliance shall be made available upon request by the Government.

PACKAGING/PACKING: Six (6) rolls of unwrapped Jumbo roll 2-ply toilet tissue shall be packed in a close-fitting corrugated fiberboard box. The complete shipping container shall not exceed 51 pounds in weight, and shall be in compliance with the Uniform Freight Classification and Item of the National Motor Freight Classification.



UI: BX (Six (6) rolls of unwrapped Jumbo roll 2-ply toilet tissue shall be packed in a close-fitting corrugated fiberboard box)

NSN: 8540-01-590-9069


OVERALL LENGTH 600 FEETOVERALL WIDTH 8.250 INCHESOVERALL INSIDE CORE DIAMETER 2.250 INCHESMATERIAL FIBROUS, CELLULOSIC MATERIAL, CHLORINE-FREEPLY QUANTITY 2COLOR WHITEUSAGE FORM ROLLUNIT PACKAGING FORM BOXUNIT PACKAGE QUANTITY 6 ROLLS PER BOX


CHARACTERISTIC REQUIREMENT TAPPI TESTBasis Weight per ply (24 x 36 -500) Grammage, g/m2 (pounds) Min 11.5 T410

Water absorption 0.1ml, Seconds (max) 10 seconds T432


average of both directions Dry 42 oz/in T404 Wet 12 oz/in T456

Brightness, percentAverage both sides, min 76 percent T452

Stretch target + or -2 percent Moisture, target + or -1 percentCaliper, 8 plies, inches

Red lines: No more than one per roll, None within six inches of the core, and none within 4 inches from the outside edge. No more than 25 percent of a shipment may contain red lines________________________________________________________________________________*Before Tappi T432 is performed the paper should be conditioned according to Tappi T402.

PACKAGING/PACKING: Six (6) rolls of paper towels per box shall packaged in accordance with normal commercial practice and packed to assure acceptance by common carrier and to provide product protection against loss or damage during multiple shipments, handling and storage. The shipping container shall be in compliance with the National Motor Freight Classification and the Uniform Freight Classification, and shall not be more than 51 pounds in weight.



UI: BX (Six (6) rolls of paper towels per box)

NSN: 8540-01-590-9072


OVERALL WIDTH 3.7000 INCHES (+/- 0.1250 INCHES) OVERALL LENGTH 2000.0 INCHESOVERALL OUTSIDE DIAMETER 9.0000 INCHESOVERALL CORE DIAMETER 3.3000 INCHESMATERIAL FIBROUS, CELLULOSIC MATERIAL


COLOR WHITEPLY QUANTITY 1ROLL SIZE JUMBO USAGE FORM ROLLUNIT PACKAGING FORM BOXUNIT PACKAGING QUANTITY 12 ROLLS PER BOX


The paper shall be wound evenly on a round paper board, and specified the requirement of Table 1 below.

TABLE IPhysical Requirements

________________________________________________________________________________CHARACTERISTIC REQUIREMENT TAPPI________________________________________________________________________________Basis Weight (24 x 36 -500) Grammage, g/m2 (pounds) Min 10.2 T410________________________________________________________________________________Water absorption 0.1ml, Seconds (max) 35 seconds T432 ________________________________________________________________________________Tensile strength, dry CD, grams 150(1 ) per ply, min/target/max 250

N/A T494________________________________________________________________________________Tensile strength, dry MD, grams 450(1 ) per ply, min/target/max 500

550 T494________________________________________________________________________________Brightness, percentAverage both sides, min 76 percent T452________________________________________________________________________________Stretch target + or -2 percent 10________________________________________________________________________________Moisture, target + or -1 percent 6________________________________________________________________________________Caliper, 8 plies, inches .027-.030________________________________________________________________________________Red Lines/ Paper Breaks: No more than two per parent roll, none within 6 inches of the core, and none within 4 inches from the outside edge. No more than 25% of a shipment may contain red lines________________________________________________________________________________*Before Tappi T432 is performed the paper should be conditioned according to Tappi T402.

ODOR. Tissue shall have no disagreeable odor when dry or wet. To test for odor when wet, soak a single tissue in distilled water at room temperature for 2 minutes. Remove the tissue from the water and smell the tissue at a distance of 304 610 mm (12 -24 inches). Any disagreeable odor shall be

cause for rejection. Supplier shall certify that the tissue shall not clog or interfere with the water flow of waste lines or septic systems.


PACKAGING/PACKING: Twelve (12) rolls of unwrapped Jumbo roll single-ply toilet tissue shall be packed in a close-fitting corrugated fiberboard box. The complete shipping container shall not exceed 51 pounds in weight, and shall be in compliance with the Uniform Freight Classification and Item of the National Motor Freight Classification.



UI: BX (Twelve (12) rolls of unwrapped Jumbo roll single-ply toilet tissue shall be packed in a close-fitting corrugated fiberboard box)

NSN: 8540-01-590-9073 PAPER, TOILET

DESCRIPTION


OVERALL WIDTH 3.7000 INCHES (+/- 0.1250 INCHES)OVERALL LENGTH 1000.0 INCHESOVERALL OUTSIDE DIAMETER 9.0000 INCHESOVERALL CORE DIAMETER 3.3000 INCHESMATERIAL FIBROUS, CELLULOSIC MATERIALPLY QUANTITY 2ROLL SIZE JUMBO USER FORM ROLLCOLOR WHITEUSAGE FORM ROLLUNIT PACKAGING QUANTITY 12QUANTITY PER UNIT 12 ROLLS PER BOX


The paper shall be wound evenly on a round paper board, and specified the requirement of Table 1 below.

TABLE IPhysical Requirements


________________________________________________________________________________CHARACTERISTIC REQUIREMENT TAPPI________________________________________________________________________________Basis Weight per ply (24 x 36 -500) Grammage, g/m2 (pounds) Min 8.5 T410________________________________________________________________________________Water absorption 0.1ml, Seconds (max) 5 seconds T432 ________________________________________________________________________________Tensile strength, dry CD, grams 150(1 ) per ply, min/target/max 250

N/A T494________________________________________________________________________________Tensile strength, dry MD, grams 300(1 ) per ply, min/target/max 350

400 T494________________________________________________________________________________Brightness, percentAverage both sides, min 76 percent T452________________________________________________________________________________Stretch target + or -2 percent 10 ________________________________________________________________________________Moisture, target + or -1 percent 6________________________________________________________________________________Caliper, 8 plies, inches .027-.030________________________________________________________________________________Red Lines/ Paper Breaks: No more than two per parent roll, none within 6 inches of the core, and none within 4 inches from the outside edge. No more than 25 percent of a shipment may contain red lines________________________________________________________________________________*Before Tappi T432 is performed the paper should be conditioned according to Tappi T402.

ODOR. Tissue shall have no disagreeable odor when dry or wet. To test for odor when wet, soak a single tissue in distilled water at room temperature for 2 minutes. Remove the tissue from the water and smell the tissue at a distance of 304 610 mm (12 -24 inches). Any disagreeable odor shall be cause for rejection. Supplier shall certify that the tissue shall not clog or interfere with the water flow of waste lines or septic systems.


PACKAGING/PACKING: Twelve (12) rolls of unwrapped toilet tissue shall be packaged in accordance with normal commercial practice and packed to assure acceptance by common carrier and to provide product protection against loss or damage during multiple shipments, handling and storage. The shipping container shall be in compliance with the National Motor Freight Classification and the Uniform Freight Classification, and shall not be more than 51 pounds in weight.



UI: BX (Twelve (12) rolls of unwrapped toilet tissue shall be packaged in a box)


Date post:	16-Mar-2018
Category:	Documents
Upload:	buiminh
View:	218 times
Download:	3 times

Ironing board design and construction - Home | Interact personal... · Web viewThe ironing board...

Documents