Disclosure to Promote the Right To Information Whereas the Parliament of India has set out to provide a practical regime of right to information for citizens to secure access to information under the control of public authorities, in order to promote transparency and accountability in the working of every public authority, and whereas the attached publication of the Bureau of Indian Standards is of particular interest to the public, particularly disadvantaged communities and those engaged in the pursuit of education and knowledge, the attached public safety standard is made available to promote the timely dissemination of this information in an accurate manner to the public. इंटरनेट मानक “!ान $ एक न’ भारत का +नम-ण” Satyanarayan Gangaram Pitroda “Invent a New India Using Knowledge” “प0रा1 को छोड न’ 5 तरफ” Jawaharlal Nehru “Step Out From the Old to the New” “जान1 का अ+धकार, जी1 का अ+धकार” Mazdoor Kisan Shakti Sangathan “The Right to Information, The Right to Live” “!ान एक ऐसा खजाना > जो कभी च0राया नहB जा सकता ह ै” Bhartṛhari—Nītiśatakam “Knowledge is such a treasure which cannot be stolen” IS 15424-5 (2004): Tools for Pressing - Guide Pillars, Part 5: Type D, End-Locking Pillars with Flange [PGD 4: Metal Forming Machines]
Transcript
Disclosure to Promote the Right To Information
Whereas the Parliament of India has set out to provide a practical regime of right to information for citizens to secure access to information under the control of public authorities, in order to promote transparency and accountability in the working of every public authority, and whereas the attached publication of the Bureau of Indian Standards is of particular interest to the public, particularly disadvantaged communities and those engaged in the pursuit of education and knowledge, the attached public safety standard is made available to promote the timely dissemination of this information in an accurate manner to the public.
इंटरनेट मानक
“!ान $ एक न' भारत का +नम-ण”Satyanarayan Gangaram Pitroda
“Invent a New India Using Knowledge”
“प0रा1 को छोड न' 5 तरफ”Jawaharlal Nehru
“Step Out From the Old to the New”
“जान1 का अ+धकार, जी1 का अ+धकार”Mazdoor Kisan Shakti Sangathan
“The Right to Information, The Right to Live”
“!ान एक ऐसा खजाना > जो कभी च0राया नहB जा सकता है”Bhartṛhari—Nītiśatakam
“Knowledge is such a treasure which cannot be stolen”
“Invent a New India Using Knowledge”
है”ह”ह
IS 15424-5 (2004): Tools for Pressing - Guide Pillars, Part5: Type D, End-Locking Pillars with Flange [PGD 4: MetalForming Machines]
IS 15424 (Part 5): 2004ISO 9182-5:1992
Indian Standard
TOOLS FOR PRESSING — GUIDE PILLARSPART 5 TYPE D, END-LOCKING PILLARS WITH FLANGE
ICS 25.20.10
0 BIS 2004
BUREAU OF INDIAN STANDARDSMANAK BHAVAN, 9 BAHADUR SHAH ZAFAR MARG
NEW DELHI 110002
June 2004 Price Group 2
Metal Forming Machines Sectional Committee, BP 04
NATIONAL FOREWORD
This Indian Standard (Part 5) which is identical withISO9182-5: 1992 ‘Tools for pressing — Guide pillars— (Part 5) : Type D, end-locking pillars with flange’ issued by-the International Organization forStandardization (ISO) was adopted by the Bureau of Indian Standards on the recommendations of theMetal Forming Machines Sectional Committee and approval of the Basic and Production EngineeringDivision Council.
The text of the ISO Standard has been approved as suitable for publication as an Indian Standard withoutdeviations. Certain conventions are, however, not identical to those used in Indian Standards. Attention is
particularly drawn to the following:
a) Wherever the words ‘International Standard’ appear referring to this standard, they should be readas ‘Indian Standard’.
b) Comma (,) has been used as a decimal marker in the International Standard, while in IndianStandards, the current practice is to use a point (.) as the decimal marker.
In the adopted standard, reference appears to the following International Standard for which Indian Standardsalso exist. The corresponding Indian Standards which are to be substituted in their place are listed belowalong with their degree of equivalence for the editions indicated:
International Standard Corresponding Indian Standard Degree ofEquivalence
ISO 6753: 19821) Machined IS 11143 (Part 1) :2002 Tools for pressingplates for press tools, moulds, and moulding-machined plates: Part 1jigs and fixtures — Nominal Machined plate for press tools jigs and fixturesdimensions (first revision) Identical
IS 11143 (Part 2) :2002 Tools for pressingand moulding-machined plates: Part 2Machined plates for moulds (first revision)
For the purpose of deciding whether a particular requirement of this standard is complied with, the finalvalue, observed or calculated, expressing the result of a test or analysis shall be rcwnded off in accordancewith IS 2 : 1960 ‘Rules for rounding off numerical values (revised)’. The number of significant placesretained in the rounded off value should”be the same as that of the specified value in this standard.
v Revised and corresponding Indian Standards are based on ISO 6753 (Parts 1 and 2).
ts 15424 (Part 5) :2004ISO 9182-5:1992
Indian Standard
TOOLS FOR PRESSING — GUIDE PILLARSPART 5 TYPE D, END-LOCKING PILLARS WITH FLANGE
1 Scope
This part of ISO 9182 specifies the dimensions andtolerances, in millimetres, of guide pillars, type D,end-locking pillars with flange, intended for use inpress tools.
It gives guidance on materials and specifies thehardness and the designation of guide pillars whichmeet the requirements of this part of ISO 9182.
2 Normative reference
The following standard contains provisions which,
through reference in this text, constitute provisionsof this part of ISO 9182. At the time of publication,the edition indicated was valid. All standards aresubject to revision, and parties to agreements basedon this part of ISO 9182 are encouraged to investi-gate the possibility of applying the most recent edi-tion of the standard indicated below. Members ofIEC and ISO maintain registers of currently validInternational Standards.
ISO 6753:1982, Machinedmoulds, jigs and fixtures —
3 Dimensions
See figure 1 and table 1.
plates for press tools,Nominal dimensions.
4 Material and hardness
The material is left to the manufacturer’s discretion.The hardness shall be (62 “’~) HRC,
5 Designation
Guide pillars for press tools in accordance with thispart of ISO 9182 shall be designated by
a) “Guide pillar”;
b) reference to this part of ISO 9182;
c) its type;
d) its diameter, d,, in millimetres;
e) its length, 12, in millimetres;
f) its length, 1, in millimetres.
EXAMPLE
The designation for a guide pillar, type D, of diam-eter 4 = 12 mm, length /2= 12 mm and lengthf= 63 mm is as follows:
Guide pillar ISO 9182-5- D -12 x 12 x 63
1
IS 15424 (Part 5) :2004ISO 9182-5:1992
a%Sllghtly rounded” G
1 em
/ofQ [ —-+” ‘“- -
1, 6.3 ● 0,1Centre ootlonnl
1 1
1) The values of the radll ore Left to the manufacturer’s discretion.21The tolerance J6maybe reducedtor a certain port of Length12to act as a pilot for flttlng purposes.
- Radlue
b-——.Alternotlve
Figure 1 – End-locking guide pillar with flange
2
IS 15424 (Part 5) :2004ISO 9182-5:1992
/
r1 min.
r2 min.
o1
12. 16 20 25 32 40 50 63 80 100
16 20 25 32 40 50 63 80 100 125
4 4 4 6 6 ““ 6 8 8 .8 8
12 16 20 25 32 40 50 50 63 63
63 x
80 x x x x
90 x x x x x
100 x x x x xi
112 x x x x x
125 x x x x x x x
140 x x x x x x
160 x x x x x x x—
180 x x x x x x x
200 x x x x x x
224 x x x x x
250 x x x x x x
280 x x x x x, ,
315 x x x x x——— ..——— ———
355 x x x x x
400 x x x x.—
450 x x x x
-...I 1~1._J-----ll”l AIx
NOTES
1 x standardized dimensions.
2 Larger values of Iz shall be chosen as a function of other dimensions such as the plate thickness in accordance withISO 6753.
3 To prevent an incorrect assembly of the upper and lower plates of the die set in relation to each other, the followingvalues for diameter d, are recommended: 11, 15, 19, 24, 30, 38, 48 and 60.
IS 15424 (Part 51:2004ISO 9182-5:1992
Annex A
(informative)
Bibliography
[1] ISO 6508:1986, Mets//ic materiak – Hardness test – Rockwe// test (scales A - B - C - D - E - F -G - H .K).
[2] ISO 9182-1:1992, Too/s for pressing – Guide pillars – Part 1: Types.
4
Bureau of Indian Standards
BIS is a statutory institution established under the Bureau of /rrdian Standards Act, 1986 to promoteharmonious development of the activities of standardization, marking and quality certification of goodsand attending to connected matters in the country.
Copyright
BIS has the copyright of all its publications. No part of these publications may be reproduced in anyform without the prior permission in writing of BIS. This does not preclude the free use, in the course ofimplementing the standard, of necessary details, such as symbols and sizes, type or grade designa-tions. Enquiries relating to copyright be addressed to the Director (Publications), BIS.
Review of Indian Standards
Amendments are issued to standards as the need arises on the basis of comments. Standards arealso reviewed periodically; a standard along with amendments is reaffkmed when such review indl-cates that no changes ars needed; if the review indicates that changes are needed, it is taken up forrevision. Users of Indian Standards should ascertain that they are in possession of the latest amend-ments or edition by referring to the latest issue of ‘BIS Catalogue’ and ‘Standards: Monthly Additions’.
This Indian Standard has been developed from Doc : No. ‘BP 04 (0376).
Amendments Issued Since Publication
Amend No. Date of Issue Text Affected
BUREAU OF INDIAN STANDARDS
Headquarters :
Manak Bhavan, 9 Bahadur Shah Zafar Marg, New Delhi 110002 Telegrams : ManaksansthaTelephones :23230131,23233375,2323 9402 (Common to all offices)
Regional Offices : Telephone
Central :
Eastern :
Northern :
Southern :
Western :
Manak Bhavan, 9 Bahadur Shah Zafar Marg
{
23237617NEW DELHI 110002 23233841
1/14 C.I,T. Scheme Vli M, V. I. P. Road, Kankurgachi
