Disclosure to Promote the Right To Information
Whereas the Parliament of India has set out to provide a practical regime of right to information for citizens to secure access to information under the control of public authorities, in order to promote transparency and accountability in the working of every public authority, and whereas the attached publication of the Bureau of Indian Standards is of particular interest to the public, particularly disadvantaged communities and those engaged in the pursuit of education and knowledge, the attached public safety standard is made available to promote the timely dissemination of this information in an accurate manner to the public.
इंटरनेट मानक
“!ान $ एक न' भारत का +नम-ण”Satyanarayan Gangaram Pitroda
“Invent a New India Using Knowledge”
“प0रा1 को छोड न' 5 तरफ”Jawaharlal Nehru
“Step Out From the Old to the New”
“जान1 का अ+धकार, जी1 का अ+धकार”Mazdoor Kisan Shakti Sangathan
“The Right to Information, The Right to Live”
“!ान एक ऐसा खजाना > जो कभी च0राया नहB जा सकता है”Bhartṛhari—Nītiśatakam
“Knowledge is such a treasure which cannot be stolen”
“Invent a New India Using Knowledge”
है”ह”ह
IS 3311 (1979): waste plug and its accessories for sinksand wash-basins [CED 3: Sanitary Appliances and WaterFittings]
IS : 3311 - 1979
Indian Standard SPECIFICATION FOR
WASTE PLUG AND ITS ACCESSORIES FOR SINKS AND WASH-BASINS
( First Revision )
Sanitary Appliances and Water Fittings Sectional Committee, BDC 3
Chairman
SHRI V. D. DESAI
Members
Rcjmrrnfing
Bombay Municipal Corporation
AD~ISEB Central Public Health & Environmental Engineer- ing Organization ( Ministry of Works & Housing )
SHRI B. B. RAU ( &tern& ) SHRI M. K. BASU Central Glass & Ceramic Research Institute
( CSIR ), Ahmadabad SWRI K. D. BISWAS Indian Iron & Steel Co Ltd, Calcutta SHRI D. S. CHABHAL Directorate General of Technical Development,
New Delhi SERI T. RAMASUBRAMANIAN ( Alternate )
SHRI S. P. CHAKRABARTY Cent_;olrkF;ilding Research Institute ( CSIR ),
SHRI S. K. SHA~MA ( Alternate > CHIEF ENQINEER’ Public Health Engineering Department, Government
of Kerala, Trivandrum SHRI K. RAMACHANDRAN ( Alternate )
CHID- ENGINEER Tamil Nadu Water Supply & Drainage Board, Madras
CHIEI+ ENQINEEE U. P. Jai N&am, Lucknow SUPERINTENDING ENGINEER ( Alternate )
CHIEF ENGINEER ( WATER ) Municipal Corporation of Delhi, Delhi DRAINAQX ENGINEER ( Adfarnale )
SHRI L. M. CR~UDIIARY Public Health Engineering Department, Government of Haryana, Chandigarh
SHRI I. CHAXDRA ( Al&mu~fr )
( Co&n ucd on page 2 )
@ Copyright 1980 INDIAN STANDARDS INSTITUTION
This publication is protected under the Indian Copyright Act ( XIV of 1957 ) and reproduction in whole or in part by anv means except with written permission of the publisher shall be deemed to be an infringement of copyright under the said Act.
IS : 3311- 1979
Membrrs Repr6smting
CITY ENQINEER Bombay Municipal Corporation HYDRAULIC ENGINEER ( Ahmat )
SHRI H. N. DALLAS Indian Institute of Architects. Bombay DIRECTOR Bombay Potteries & Tiles Ltd, Bombay
SRRI A. M. KEMBHAVI ( Allernatc ) SH~I B. R. N. GUPTA Engineer-in-Chief’s Branch ( Army Headquarters )
SERI K. V. KRISHNAMURTEY ( Altcrnn~a ) SHRI M. T. KANSE Directorate General of Supplies & Disposals New
Delhi SHRI S. R. KSHIRSAQAR National Environmental Engineering Research
Institute ( CSIR ), Nagpur SHRI R. C. REDDY ( Alternuts)
SERI K. LAPSBMINALAYANAN Hindustan Shipyard Ltd, Vishakhapatnam SHRI A. SKAXIFF ( Ahrnds )
SHRI E. K. RAMAOHANDRAN National Test House, Calcutta SHRI S. K. BANERJEE ( Altcrnata )
SERI RAN JIT SINGE Railway Board ( Ministry of Railways ) DR A. V. R. RAO National Buildings Organization, New Delhi
SHRI J. SENGUPTA ( Ahnote ) SHRI P. JAGANATH RAO E. I. D.-Parry Ltd, Madras
SHPI M. MOOSA SULAIMAN ( Alternate ) SHRI R. K. SOMANY Hindustan Sanitaryware & Industries Ltd,
Bahadurgarh SURVEYOR OF WORKS ( ND2 ) Central Public Works Department, New Delhi
SURVEYOR OR WORKS I ( NDZ ) ( Alternat )
SHRI D. AJIT~A SIMHA, Director ( Civ Engg )
Director General, ISI ( Ex-&io Member )
SHRI S. P. MAQGU Assistant Director ( Civ Engg ), ISI
Domestic Sanitary Appliances and Accessories Subcommittee, BDC 3 : 1
Convener
SHRI G. F. KEAXBATTI Bombay Municipal Corporation
Membrrs
SHRI M. C. AQRAWAL SHRI N. L. BIRLA C A/f6mt6 1
ASSISTANT DIRECTOR, STANDARDS ( ARCHITECTURE ) ( RDSO )
SHRI M. K. BASU
Indian Plastics Ltd, Bombay
Ministry of Railways
Central Glass & Ceramic Research Institute ( CSIR ), Ahmadabad
SHRI S. P. CHAXRABARTY
CHIEF ENQINEER
Central Building Research Institute ( CSIR ), Roorkee -
Public Health Engineering Department, Government of Kerala
SHRI K. RAMACHAXDBAN ( All6matr )
( Confinucd on page 7 )
L
IS:3311 - 1979
Indian Standard SPECIFICATION FOR
WASTE PLUG AND ITS ACCESSORIES FOR SINKS AND WASH-BASINS
( First Revision )
0. FOREWORD
0.1 This Indian Standard ( First Revision ) was adopted by the Indian Standards Institution on 31 December 1979, after the draft finalized by the Sanitary Appliances and Water Fittings Sectional Committee had been approved by the Civil Engineering Division Council.
0.2 This standard was first printed in 1965. As a result of experience gained during these years and the publication of the revised standards for wash-basins and sinks. it has been decided to revise this standard. Reference to the new standard ( IS : 7608-1975* ) as material for chain has been introduced.
0.3 In the formulation of this standard, due weightage has been given to international co-ordination amc;ng the standards and practices prevailing in diffcrcnt countries in addition to relating it to the practices in the field iv this country.
0.4 For the purpose of deciding whether a particular requirement of this standard is complied with, the final value, observed or calculated, expressing the result of a test or analysis, shall be rounded off in accordance with IS : 2-1960t The number of significant places retained in the rounded off values should be the same as that of the specified value in this standard.
1. SCOPE
1.1 This standard covers the requirements for materials, manufacture, construction, testing and finish of waste plug, chain and stay suitable for
*Specification for phosphor bronze wires ( for general engineering purposes ). tRulcs for rounding off numerical values ( r&sad ).
3
IS : 3311.1979
use in wash-basins and sinks complying with IS : 771 ( Part II )-1979*, 1s : 2556 ( Part IV )-1972t and IS : 2556 ( Part V )-19795.
1.1.1 The dimensions of the waste plug have been specified so as to suit waste fittings covered in IS : 2963-1979s.
2. MATERIALS, MANUFACTURE AND CONSTRUCTION
2.1 Waste Plug - The waste plu, u shall be made of rubber of hard and durable quality having sufficient chemical resistance to resist normal disinfectants used in cleaning wash-basins and sinks. It may also be made of any other equally suitable material. The depth and thickness of the plug shall be such as to provide and maintain required rigidity and watertightness.
2.1.1 Each waste plug shall have a loqse shackle which provides a suitable anchor for the plug chain. The shackle and other metal components, if any, of the plug shall be of brass or other equally suitable corrosion resistant material.
2.1.2 The shape and dimensions of plug shall be as shown in Fig. 1.
2.2 Chain - The chain shall be manufactured from phosphor bronze or brass wire conforming to IS : 7608-197511 and IS : 2704-19647 respectively or from any other equally suitable corrosion resistant material as agreed to between the manufacturer and the purchaser. Where it is made from bronze or brass wire, it shall have a minimum diameter of 1.80 mm with brazed oval links approximately 13 mm in length. The overall length of the chain ( excluding shackle ) shall be not less than 300 mm. One end of the chain shall be securely attached to the shackle of the waste plug and the other end to the shackle of the stay.
2.3 Stay - Chain stay shall be of bolt type or screw type as specified by the purchaser and shall be made of brass or any other equally suitable corrosion resistant material. The shank of the stays shall be fully threaded to the underside of the flange.
*Specification for glazed fire-clay sanitary appliances: Part II Specific requirements of kitchen and laboratory sinks ( second mision ).
tSpccification for vitreous sanitary appliances ( vitreous china ): Part IV Specific requirements of wash-basins ( second rcaisiun ):
ISpecification for vitreous sanitary appltances ( vitreous china ): Part V Specific requi emcnts of laboratory sinks ( second revirion ).
SSpecification for copper allov waste fittines for wash-basins and sinks (/;rst revision ). [ISpecification for phosphor bronze wires ( for general rngineering purposes ). ISpecification for brass wire for cold-headed and machined parts.
4
1979
BOLT TYPE STAY
DETAILS FOR SCREW TYPE STAY
SIZE WASH BASIN SINK
A 42 60 ~ 13 APPROX-, _
METALLIC PORTION (OPTIONAL)
SHACKLE
t 10 MIN
15 MAX
WASTE PLUG
, I
I
SECTION XX TAPER 1 IN 7/ ----I X
NOTE - This illustration is not intended to indicate details of design.
All dimensions in millimetres.
FIG. 1 TYPICAL DETAILS OF WASTE PLUG AND CHAIN WITH STAY FOR SINKS AND WASH-BASINS
5
IS : 3311- 1979
2.3.1 Bolt type shall conform to the following dimensions:
Dia of flange, Min 12 mm
Dia of threaded shank M5 [ see IS : 4218 ( Part II )-1976* 1
Length of shank, Min 50 mm
Thickness of nut, Min 6.5 mm
2.3.2 Screw type shall conform to the following dimensions:
Flange dia, Min 12 mm
Shank length, Min 20 mm
Thread on shank No. 11 wood screw thread ( IS : 451-1972t )
2.4 Illustration of a typical construction of waste plug, chain and stay is given in Fig. 1.
3. LOAD TEST
3.1 The complete assembly of waste plug, chain and stay shall be capable of withstanding a load of not less than 200 N ( 20 kg ) without visible deformation.
4. FINISH 4.1 Plug chain and stay shall be chromium-plated. The quality of chromium plating shall not be less than Service Grade No. 2 of IS : 4827- 19681.
5. MARKING
5.1 Manufacturer’s name or trade-mark may be legibly marked on any portion of the assembly of waste plug, chain and stay.
5.1.1 Each waste plug, chain and stay may also be marked with the ISI Certification Mark.
NOTE - The use of the IS1 Certification Mark is governed by the provisions of the Indian Standards Institution ( Certification Marks ) Act and the Rules and Regulations made thereunder. The ISI Mark on products covered by an Indian Standard conveys the assurance that they have been produced to comply with the requirements of that standard under a well-defined system of inspection, testing and quality control which is devised and supervised by IS1 and operated by the producer. IS1 marked products are also continuously checked by IS1 for conformity to that standard as a further safeguard. Details of conditions under which a licence for the use of the IS1 Certification Mark may be granted to manufacturers or orocessors. may be obtained from the Indian Standards Institution.
*ISO metric screw threads: Part II Diameter pitch combinations (first rcuision ). tTechnica1 supply conditions for wood screws ( second reuision ). SSpecification for electroplated coatings of nickel and chromium on copper and
copper alloys.
6
IS a 3311 - 1979
( Continued from page 2 )
Mcmbrrs Representing
CnrEs ENGINEER ,
Tam~a~~a~u Water Supply & Drainage Board,
CHIEF ENQINEER ( WATER ) Municipal Corporation of Delhi ADDITIONAL CHIEF ENQINEER ( WATER ) ( Aftccmate )
CITY ENQINEER Bombay Municipal Corporation DIRECTOR Bombay Potteries & Tiles Ltd, Bombay
SHRI A. M. KEBSBHAVI ( Alternate ) SHRI M. K. GANPULE Parshuram Pottery Works Co Ltd, Thangadh
SHRI R. M. JOSSI ( Alfsrnatc ) SHRI B. R. N. GUPTA Ministry of Dcfence
SHRI K V. KRISHNAMURTEY ( Altrrnate ) SHRI M. T. KANSE Directorate General of Supplies & Disposals,
New Delhi SHRI B. K. MALHAN In personal capacity ( 9 .Tain Mandir Road, New Dslhi ) SHRI B. S. MIKCHANDANI Phenoweld Polymer Private Limited, Bombay
SRRI P. R. GUPTA ( Alternate ) SHRI B. J. PCNTONY Neiveli Ceramics & Refractories Limited
SHRI UMATOSH SARKAR ( Altrrnats ) SRRI P. JAOANATH RAO E. I. D. -Parry Ltd Madras
SHRI M. MOOSA SULAIMAN ( Altrrnatc ) SHRI L. R. SEHGAL L. R. Sehgal & Company, New Delhi SHRI AMAL KUMAR SEN Bengal Enamel Works Ltd, Calcutta SBRI J. SENQUPTA National Buildings Organization, New Delhi
SHRI 0. P. RATRA ( Alternate ) SHRI R. K. SOMANY Hindustan Sanitaryware & Industries Ltd,
Bahadurgarh SURVEYOR OF WORKS ( NDZ ) Central Public Works Department, New Delhi SHRI S. A. TUNaARE The Indian Institute of Architects, Bombay
7
INTERNATIONAL SYSTEM OF UNITS ( SI UNITS )
Base Units
QUANTITY
Length
Mass
Time
Electric current
Thermodynamic temperature
Luminous intensity
Amount of substance
Supplementary Units
QUAiXTlTT
Plane angle
Solid angle
Derived Unita
QUABTITI
Force
Energy
Power
Flux
Flux density
Frequency
Electric conductance
Electromotive force
Pressure, stress
UNIT
metrc
kilogram
second
ampere
kelvin
candela
mole
UNIT
radian
steradian
UNIT
newton
joule
watt
weber
tesla
herta
siemens
volt
Pascal
SYMBOL
m
kg s
A
Ii .
cd
mol
SYMBOL
rad
sr
SYMBOL
N
J W
Wb
T
HZ
S
V
Pa
I N = 1 kg.m/s*
1 J = 1 N.m
1 w - 1 J/s 1 Wb - 1 V.s
1 T = 1 Wb/m*
1 Ha = 1 c/s (s-1)
1 S - 1 A/V
1 v = 1 W/A
1 Pa = 1 N/m*