8/12/2019 is.4260.2004

1/10

IS 4 6 : 4

\\ \fi timIndian Standard

RECOMMENDED PRACTICE FOR ULTRASONICTESTING OF BUTT WELDS IN FERRITIC STEEL

Third Revision

ICS 77.040.20

0 BIS 2004

BUREAU OF INDIAN STANDARDSMANAK BHAVAN, 9 BAHADUR SHAH ZAFAR MARGNEW DELHI 110002November 2004 Price Group 4

8/12/2019 is.4260.2004

2/10

Non-destructive Testing Sectional Committee, MTD 21

FOREWORDThis Indian Standard Third Revision was adopted by the Bureau of Indian Standards, after the draft finalizedby the Non-destructive Testing Sectional Committee had been approved by the Metallurgical Engineering DivisionCouncil.This standard was first published in 1967 and subsequently revised in 1975 and 1986. This has now beenrevised again in the light of experience gained and the latest developments in ultrasonic testing of welds. Therequirements for distance amplitude correction examination procedure and periodic calibration have beenmodified.This standard is intended to be a guide for method of ultrasonic testing of welds by direct contact pulse echoreflection method.For general technique relating to ultrasonic testing, reference may be made to IS 3664:1981 Code of practicefor ultrasonic pulse echo testing by contact and immersion methods @st revision .This standard gives detailed procedure of examination of butt welds in ferritic steel.For the purpose of deciding whether a particular requirement of this standard is complied with, the final value,observed or calculated, expressing the result of a test or analysis, shall be rounded off in accordance withIS 2:1960 Rules for rounding off numerical value revised . The number of significant places retained in therounded off value should be the same as that of the specified value in this standard.

8/12/2019 is.4260.2004

3/10

IS 4260:2004Indian Standard

RECOMMENDED PRACTICE FOR ULTRASONICTESTING OF BUTT WELDS IN FERRITIC STEEL

Third Revision1 SCOPE1.1 This standard prescribes a method for ultrasonictesting and inspection of welds by direct contact pulseecho reflection method. This method is applicable tomaterial thickness over 5 mm.1.2 These requirements are established for detection,location and evaluation of reflection within the weld,heat affected zone and adjacent material. Theexamination classification are:

a Welds in ferritic product forms in wrought andcast materials, other than pipes; andb Ferritic welds in ferritic pipes.

1.3 This standard covers technique to be employed atnormal temperature. Care shall be taken to ensurethat the temperature of test piece is not above thetemperature for which the probe is designated.2 REFERENCESThe following standards contain provisions, whichthrough reference in this text, constitute provisions ofthis standard. At the time of publication, the editionsindicated were valid. All standards are subject torevision, and parties to agreements based on thisstandard are encouraged to investigate the possibilityof applying the most recent editions of the standardsindicated below

1S No.2417:2003

3664:1981

8791:1971

12666:1988

13805:2004

TitleGlossary of terms relating toultrasonic testing firstrevisionCode of practice for ultrasonicpulse echo testing by contact andimmersion method jirstrevisionCode of practice for ultrasonicflaw detection of ferritic steelforgingMethod for performanceassessment of ultrasonic flawdetection equipmentGeneral standard forqualification and certificationof non-destructive testingj~ersonnel

3 TERMINOLOGYFor the purpose of this standard, the definitions givenin IS 2417 shall apply.4 EQUIPMENT4.1 The ultrasonic apparatus shall be capable ofproducing, receiving and displaying high frequencyacoustic pulses over the nominal range of 1to 5 MHLand shall be of pulse echo reflection type. Otherfrequencies may be used, if equal to better sensitivitycan be demonstrated.4.2 The ultrasonic instruments and probes shall becapable of being used without difficulty in thetemperature range of 10 to + 50C.4.3 The ultrasonic instrument shall provide linearvertical presentation within + 5 percent of fill screenheight from 20 to 80 percent of the full screen height.The screen height linearity shall be measured andrecorded in accordance with IS 12666.4.4 The ultrasonic apparatus shall have an amplitudecontrol, accurate over its useful range of* 20 percentof the nominal amplitude ratio to allow measurementof indications beyond the linear range of the verticaldisplay on the screen. The amplitude control linearityshall be measured as described in IS 12666.4.5 The ultrasonic apparatus shall be adjusted for sweeprange and calibrated prior to inspection as described inIS 12666.5 TEST PROCEDURES5.1 Basic Calibration Block5.1.1 The basic calibration reflectors shall be used toestablish a primary reference response of theequipment. The basic calibration reflectors may belocated either in the finished component materialprovided the same shall not affect the serviceabilityor in a basic calibration block.5.1.2 The material from which the block is fabricatedshall be of the same product form, that is, plate, forgingbar, tubes, etc, and material specification, havingsimilar acoustic characteristics of the finishedcomponent. The thickness of basic calibration block~iidl be related to finished component thickness asshown in Table 1 corresponding to Fig. 1. When twoor more base material thicknesses are involved, the

1

8/12/2019 is.4260.2004

4/10

IS 4260:2004calibration block thicknesses shall be determinedlyaverage thickness of weld. The finish on the surfaceof the block shall be representative of the surfacefinishes on the tinished components.5.1.3 For contact examination the temperaturedifference between the examination and the calibrationblock surfaces shall be within 14C. Calibration andsensitivity setting shall be performed under temperatureconditions similar to those used in the test or appropriatecompensations for angle and sensitivity changes shallbe made.6 PROBE6.1 A shear wave probe which produces an angle of45 to 70 in the examination medium isnormally used.The selection of the beam angle is dependent on thethickness and geometry of the weld. The recommendedbeam angles for different thicknesses of material areshown below:

Thickness Beam Angle Insidemm the Mediumdegreeup to 30 70Over 30 to 50 60Over 50 45

6.2 Probes with a beam angle less than 45 and morethan 70 may be used, if the geometry of the weld ismore adoptable to the chosen beam angle. Shoes maybe found necessary to fit into the probes to suit the

curvature of the surface. Whenever such probes areused for examination, calibration also has to be donewith the same type.6.3 The nominal frequency shall be in the range of 2to 5 MHz. Unless variables such as production materialand grain structure require the use of other frequenciesto assure adequate penetration or better resolution.7 COUPLANTA satisfactory couplant, liquid or paste, having goodwetting properties to permit the transmission ofmechanical vibrations between the probe and materialunder test shall be used. Oil, glycerine, water greases;silicone and white lead paste are among the morecommonly used couplants.8 SURFACE PREPARATION8.1 The base metal on each side of the weld shall befree of weld spatter, surface irregularities or foreignmatter that might interface with the examination.8.2 The weld ripples or weld surface irregularitiesshall be removed by any suitable mechanical meansto such a degree that the resulting ultrasonicexamination from any remaining irregularities cannotmask any objectionable defects. The finished surfaceof the reinforcement should merge smoothly into thesurface of the adjacent base material.8.3 The volume of the base material through whichthe sound will travel in angle beam examination shall

Table 1 Thickness of Basic Calibration BlockClause 5.1.2

SI Weld Thickness, t Basic Calibration Hole DiameterNo. mm Block Thickness, T mmi 2 3 4i 25.4 or less 190rt 2:4ii Over 25.4 upto51 380rt 3.2iii Over 51 up to 102 76 Or t 4.8iv Over 102upto 151 1270rt 6.4v Over 152 up to 203 1760rt 8.0vi Over 203 up to 254 228 or t 9.6

vii Over 254 see NotesNOTES1 For such increase in thickness of 51 mm or fraction thereof, the hole diameter shall increase 1.6 mm.2 Hole shall be drilled and reamed to a minimum of 38 mm essentially parallel to the examination surface.3 Curved surfaces: For curved surfaces, two curved blocks, one for each representative curvature or two setsof calibrationreflectors oriented 90 from each other shall be used.4 Notches maybe provided as required.5 Tolerances for hole diameter shall be+ 0.8 mm.6 Tolerance on notch depth shall be + 10 and 20 percent.7 Tolerance on hole location through thickness shall be + 3.2 mm.

2

8/12/2019 is.4260.2004

5/10

IS 4260:2004

Notch Size Width= 3.2 mm or 6.4 mm, Depth= 2 percent of T or 1.0 mm,whichever is greater into the base metal, Length=51 mm

FIG.1 BASICCALIBRATIONBLOCKbe completely scanned with a straight beam searchunit usually of 2 MHz frequency to detect and recordreflections which might affect interpretation of anglebeam results. This is not intended as an acceptance/rejection examination.8.4 Dual probes may be employed in plates ofthickness 5 mm to 12 mm for detection of reflectors.9 DISTANCE AMPLITUDE CORRECTION9.1 Compensation for the distance traversed by theultrasonic beam as it passes through the material isprovided by the use of curves shown in Fig. 2.

9.2 The angle beam probe shall be directed towardsthe basic calibration reflectors in the calibration block.The centre-line of the probe shall not point towardsthe corners of the hole. The sound beam shall beoriented perpendicular to the axis of the side drilledholes. The probe is positioned for maximum responsefrom the side-drilled hole that gives the highestamplitude. The sensitivity controls are adjusted toprovide an 80 percent + 5 percent of full screenheight of full screen indication from the hole. Thepeak of the indication is marked on the CRT screen.The probes are positioned at other nodel positionscovering the expected examination range. The

SENSITIVITY >80/.

IN-LINE HOLES ANDNOTCHES USED FORANGLE BEAM CALIBRATION

100/ I80-AMPLITUDE 60-IN PERCENT

40-

20-

SIGNAL FROMNOTCH 45

FIG. 2 DISTANCE AMPLITUDE CORRECTION3

8/12/2019 is.4260.2004

6/10

IS 4260:2004corresponding peaks are marked on the CRT screen.The peaks are joined by a smooth line whose lengthcover the examination range to generate DAC curve.9.3 For evaluation of discontinuities oriented perpendi-cular to examination surface at or near the surfaces,45 probe is positioned at appropriate distancenecessary for maximum signal amplitude from thesquare notch machined on the opposite surface of thecalibration block. This amplitude reference level isalone chosen for evaluation of discontinuities at or nearthe surfaces.9.4 Ifan electronic distance amplitude correctiondeviceis used the reference response shall be equalised at50 percent of full screen height over the distance rangeemployed in the examination.9.5 For weld thickness 25 mm or less a singlecalibration reflector shall be located at 50 percent Tthickness of calibration block. No DAC curve need beestablished. The signal amplitude obtained from thereflector is kept as the reference amplitude level fortesting. The signal amplitude obtained shall beappropriate to the metal path beam bath distanceemployed for the examination ofa welded component.9.6 For straight beam examination, the straight beamprobe is positioned for maximum response from thehole that gives the highest amplitude. The sensitivitycontrol of the unit are to be adjusted to provide an 80percent of full screen height. The probe shall bepositioned for maximum response from the anotherholes and the peaks of the indication shall be markedon the screen. The peaks are smoothly connected andextended through the thickness to provide the distanceamplitude curve from the side drilled holes.10 EXAMINATION PROCEDURE10.1 The volume of the weld shall be examined bymoving the probe over the examination surface so asto scan the entire examination volume. Each pass ofthe probe shall overlap a minimum of 10percent of thetransducer piezo electric element dimensionsperpendicular to the direction of the scan.10.2 The rate of probe movement for examination shallnot exceed 150 mm/s.10.3 During movement, both towards and away fromthe welded joints of flathear flat surface, the probe shallbe oscillated over an angle 10to 15 on each side of aline normal to the centre line of the weld.11 SCANNING11.1 For straight beam examination the probe ispositioned directly on the weld surface of theexamination material. The weld shall be scannedprogressively along and across the width of weldinclusive of adjacent heat affected zone to its entirelength. Penetration is always verified with back

reflection amplitude.11.2 When dual probes are employed for examination,the included angle between the beam paths shall be suchthat the focal length of the probe is not less than thethickness of the weld under examination. Theexamination shall be performed with the planeseparating the elements of the dual probe parallel andperpendicular to the axis of the weld in two directionsas described in 11.1.11.3 The scanning shall be performed at a gain setting6 dB above the reference level. Evaluation shall beperformed at the primary reference level for straightbeam examinations.11.4 Angle beam examinations of weld thickness lessthan 10mm shall be carried out from both sides of theweld on the same surface. The total width of thescanning zone shall be equal to twice the skip distance.11.5 For weld thickness between 10mm and 100 mm,angle beam examination shall be done from both sidesof the weld on the same surface wherever practicable,the scanning zone being a full skip distance.11.6 For welds over 100 mm in thickness the weldsshall be scanned using angle beam probes from foursides, that is, from both sides of the weld from innerand outer surfaces. The probe shall be moved as nearas possible to the centre line of the weld to ensure fullcoverage. The scanning width shall be 5/8th of a skipdistance from weld centre line.12 SCANNING FOR REFLECTORS ORIENTEDPARALLEL TO WELD12.1 The angle beam shall be directed as approximateright angles to the weld axis from two directions wherepossible. The probe shall be manipulated so that theultrasonic energy passes through the required volumesof weld and adjacent base metal. The scanning shall beperformed at a gain setting of 6 dB above the referencelevel. Evaluation shall be performed with respect tothe primary reference level.12.2 Scanning for Reflectors Oriented Transverseto WeldThe angle beam shall be directed essentially parallel tothe weld axis. The probe shall be adjusted so that theangle beam passes through the required volumes ofweld metal and adjacent basemetal. The scanning shallbe performed at a gain setting 6 dB above the referencelevel and evaluation will be performed with respect tothe primary reference level. The probe shall be rotated180 and the examination repeated.13 EVALUATION13.1 Any imperfection which causes an indication inexcess of 20 percent DAC shall be investigatedto estimate the nature of flaw, then can be evaluated

4

8/12/2019 is.4260.2004

7/10

in terms of a acceptances standard. The indicationsof height 50 to 100 percent DAC shall be recorded.13.2 Recording of indication shall be made withrespect to the reference level.14 FE RRITIC WELDS IN FERRITIC PIPE14.1 Basic Calibration Block14.2 The basic calibration block for weldments shallbe a section of the same nominal size, schedule heattreatment and material specification as the materialbeing examined. The surface finish of the calibrationblock shall be representative of the surface finish ofthe piping.14.3 The basic calibration reflections shall belongitudinal and circumferential notches on both theinner and outer surfaces. The sizes and locations ofthe calibration reflectors are shown in Fig. 3.15 ANGLE BEAM CALIBRATION15.1 The nominal frequency shall be 2.0 MHz. Higherfrequencies may be used, ifthere is a need for greaterresolution.15.2 The nominal beam angle of 45 shall be used.Other angles may be used as appropriate based on theconfigurations of weld joint being examined.16 DISTANCE-AMPLITUDE CORRECTIONDAC16.1 A distance-amplitude correction DAC curve isestablished by beaming the angle beam probe towardsthe calibration reflector that yields the maximumresponse to 80 percent of full screen height. Theprobe is then manipulated without changinginstrument settings, to obtain maximum responsefrom the calibration reflectors at the distanceincrement necessary to generate a 3 point DAC curve.

IS 4260:2004Welds may be tested as described in 11, 12 and13.16.2 Selection of Calibration ReflectorsA side drilled hole may be used for initial acceptanceof pipe weld, provided that it can be demonstratedthat the hole calibration produces a sensitivity equalto or greater than the notch calibration.17 EVALUATION17.1 Any imperfection that causes an indication inexcess of 20 percent DAC shall be investigated toestimate the nature of flaw that can be evaluated interms of acceptance standard. The indications of height50 to 100 percent DAC shall be recorded.17.2 Recording of indications shall be made withrespect to the reference level.18 PROCEDURES FOR DETERMINING THELOCATION AND SIZE OF FLAWS18.1 Flaw LocationThe position of flaw within the weld maybe estimatedfrom the position of the flaw echo on the CRT screen.The distance between the flaw echo and the initialpulse as read from the calibrated time base on thescreen is the actual beam path distance W of flaw.From the known beam angle of the probe used, theprecise location of the flaw from the entry surface canbe calculated using the formula t= W cos a where t isthe thickness of component on which the probe isplaced within half skip distance from the centre of theweld. When the crystal is placed between half andfull skip distance, the formula is to be corrected as2 t- W cosa. Alternatively a flaw locating rule oraccurate sketches may by drawn to locate the flaws ina weld.

L.

: ..@

A.L 0.. . . t

~.. ..

FIG.3 ANGLE BEAM CALIBRATION PIPEWELDSTypical Block Dimensions:Length L 200 mm or 8Twhichever is greaterMinimum ARCLength A.L.i for O.D.01.6 mm or less 270 deg.

ii for O.D. greater than 101.6 mm the greater of3Tor 200 mm.SpectJ c Notch Dimensions:Length 25 mm, MinDepth 10 percent, T tolerance on depth + 10 percent -20 percent .Width 3.2 mm or 6.4 mmLocation Not closer than Tfrom any block edge.

5

8/12/2019 is.4260.2004

8/10

IS 4260:200418.2 Size of the Flaw18.2.1 In order to estimate the size of a flaw in anyparticular direction, the effective beam width at the flawposition has to be known. In the flaw size investigationit is to be determined first, whether the flaw is a largereflector or a small reflector. Large reflector is onethat is larger than the sound beam at its position, and asmall reflector is one that is smaller than the sound beamat its position.18.2.2 The size of a large reflector is determined byscanning the borders of the flaw with the ultrasonicbeam, by moving the probe from the centre of thediscontinuity until the height 6 dB drop . Thisoperation is repeated to establish the boundary. This istrue for straight beam probes and inhorizontal, verticalplane for angle beam probes.18.2.3 In case of a small reflector using angle beamprobes measurements of beam spread in the verticalplane shall be made on the side drilled holes as givenin Fig. 1 and Table 1 for appropriate thickness atdifferent distance from the shear wave probe. Toestimate the flaw size the probe is scanned so that thebeam moves parallel to vertical direction and thedistance within which the flaw echo amplitude within6 dB of the maximum, is determined. The flaw size isgiven by the difference between the probe distancemoved to touch the edges of the calibration hole andflaw in the weld multiplied by the cosine of thebeam angle inside the medium. The calibration holechosen shall be appropriate to the scanning path ofthe flaw.18.2.4 To obtain the boundary inthe horizontal plane,the shear wave probe ismoved parallel to the blind sidedrilled hole described in 18.2.3 until the amplitude dripsto 6 dB from its maximum amplitude at differentdistances from the probe. The distance from the edgeof the block to the position of crystal subtracted fromthe depth of the hole gives half-beam width. To estimatethe flaw size in a horizontal plane the probe is movedlaterally so that the beam axis moves parallel to thelateral direction and the distance is within which theflaw echo amplitude is within 6 dB of the maximum isdetermined. The flaw also is given by the differencebetween the dimensions and effective full beamwidth.19 NATURE OF FLAWS19.1 On determining the location and size of the flawand from the knowledge of defects normallyencountered in different welding processes, an estimateof the nature of flaw may be made. These differenttypes may be classified, namely, isolated pores, typeselongated worm hole and planar flaws are usuallydifferentiated by various scanning techniques.19.1.1 Isolated pores are indicated by a constant echo

signal height using a swivel scan.19.1.2 Elongated cylindrical flaws are indicated by aconstant signal height over a significant length and asharp peak for a shorter length in lateral and depthscanning depending upon the orientation of theflaw.19.1.3 Planner flaws produce sharp peaks whenscanned normal to their direction and drops suddenlywhen the probe is swivelled.20 ACCEPTANCEUltrasonic acceptance or rejection criteria for individualbutt weld shall be based on a realistic appraisal ofservice requirements that shall be established betweenthe purchaser and the manufacturer on the basis ofthe quality that can normally be obtained in suchwelds.21 CHECK FOR LINEARITY ON TIMEBASE, SCREEN HEIGHT AND AMPLITUDECONTROL21.1 Time Base LinearityWhen the time base is linear, the distance betweenrepeat echoes shall be equal. The check shall be madeat the time of calibration oftest ranges. The position ofthe echoes are noted without parallax by adjusting theecho height to 50 percent of full screen height. Thedisplayed readings shall not deviate :2 percent ofthe range calibrated or one minor dwision of thescreen.21.2 Linearity of Vertical Scale and AmplitudeControlA straight beam searchunit frequency 2 MHz or 4 MHzshall be positioned over the depth resolution notch inthe IIW block described in IS 12666 so that the signalfrom the notch is 20 percent of screen height and thesignal from the 100 mm block surface is 40 percent ofscreen height. When the sensitivity of the apparatus isaltered so that the signal from notch is raised inincrement of one major vertical scale division until the100 mm location signal reaches full scale and thenlowered in increment the smaller indication readingshall be 50 percent of the larger amplitude within5 percent of full screen height. The readings shall beestablished to the nearest of 1 percent of full screenheight.21.3 Amplitude Control LinearityTo verify the accuracy of amplitude control of theultrasonic apparatus an angle beam search unit ispositioned on the calibration block as shown in Fig. 1so that the indication from the 1/2 T hole is peaked onthe screen. With the increase and decrease in theattenuation shown in the following table the indicationmust fall within the specified limits:

6

8/12/2019 is.4260.2004

9/10

IS 4260:2004Indication Set at Control Indication Limits

Percent Full Chance, Percent of FullScreen dB Screen

80 6 32 to 4860 12 16 to 2440 +6 64to 9620 + 12 64 to 96

The settings and readings must be estimated to thenearer one percent of full screen.22 CALIBRATION CONFIRMATION22.1 Calibration shall be performed prior to use ofthe system in the thickness range under examination,a calibration check shall verify the sweep rangecalibration and distance-amplitude correction.22.2 Sweep Range CorrectionIfa point on the DAC curve has moved on the sweepline more than 10 percent of the sweep reading or5 percent of full sweep, whichever is great, correctthe sweep range calibration and note the correction inthe examination record. If reflectors are recorded onthe data sheets, those data sheets shall be avoidedand a new calibration shall be recorded. All recordedindications since the last valid calibration or calibrationcheck shall be re-examined with the corrected

calibration and their values shall be changed on thedata sheets.22.3 DAC CorrectionIf a point on the distance-amplitude correction DACcurve has decreased 20 percent or 2 dB of itsamplitude, all data sheets since the last calibration orcalibration check shall be marked void. A newcalibration shall be made and recorded and the areacovered by the voided data shall be re-examined. Ifany point of the distance-amplitude correction DACcurve has increased more than 20 percent of 2dB ofits amplitude, all recorded indications since last validcalibration or calibration check shall be re-examinedwith the corrected calibration and their values shallbe changed on the data sheets.23 PERSONNEL REQUIREMENTSPersonnel performing ultrasonic examination to therequirements of this article shall be qualified asrequired by IS 13805.24 REPORTA report of the examination shall be made. The reportshall include a record indicating the weld or volumeexamined, the location of each recorded reflector andthe identification of the operator who carried out eachexamination or part thereof. The report shall be placedin file and maintained in accordance with IS 8791 andIS 3364.

7

8/12/2019 is.4260.2004

10/10

Bureau of Indian StandardsBIS is a statutory institution established under the Bureau oJ Indian Standards Act, 1986 to promoteharmonious development of the activities of standardization, marking and quality certification of goods andattending to connected matters in the country.CopyrightBIS has the copyright of all its publications. No part of these publications may be reproduced in any formwithout the prior permission in writing of BIS. This does not preclude the free use, in the course of implementingthe standard, of necessary details, such as symbols and sizes, type or grade designations. Enquiries relating tocopyright be addressed to the Director Publications , BIS.Review of Indian StandardsAmendments are issued to standards as the need arises on the basis of comments. Standards are also reviewedperiodically; a standard along with amendments is reaffirmed when such review indicates that no changes areneeded; if the review indicates that changes are needed, it is taken up for revision. Users of Indian Standardsshould ascertain that they are in possession of the latest amendments or edition by referring to the latest issue ofCBISCatalogue and Standards: Monthly Additions.This Indian Standard has been developed from Dot: No. MTD 21 4304 .

Amendments Issued Since PublicationAmend No. Date of Issue Text Affected

BUREAU OF INDIAN STANDARDSHeadquarters:Manak Bhavan, 9 Bahadur Shah Zafar Marg, New Delhi 110002Telephones: 23230131,23233375,2323 9402 website: www.bis.org.inRegional Offices: TelephonesCentral :

Eastern :

Northern :

Southern :

Western :

Branches :

Manak Bhavan, 9 Bahadur Shah Zafar Marg { 23237617NEW DELHI 110002 232338411/14 C.I.T. Scheme VII M, V.I.P. Road, Kankurgachi

{23378499,23378561

KOLKATA 700054 23378626,23379120SCO 335-336, Sector 34-A, CHANDIGARH 160022

{26038432609285

C.I.T. Campus, IV Cross Road, CHENNAI 600113 { 22541216,2254144222542519,22542315Manakalaya, E9 MIDC, Marol, Andheri East { 28329295,28327858MUMBAI 400093 28327891,28327892AHMEDABAD. BANGALORE. BHOPAL. BHUBANESHWAR. COIMBATORE. FARIDABAD.GHAZIABAD. GUWAHATI. HYDERABAD. JAIPUR. KANPUR. LUCKNOW. NAGPUR.NALAGARH. PATNA. PUNE. RAJKOT. THIRUVANANTHAPURAM. VISAKHAPATNAM.

Printed at Simco Printing Press, Delhi