ISO/IEC 17025:2017 and ANSI/NCSL Z540.3-2006 …...Certificate of Calibration ISO/IEC 17025:2017 and...

Certificate of CalibrationISO/IEC 17025:2017 and ANSI/NCSL Z540.3-2006

Certificate Number 1-10824024277-1

Model Number E8663DManufacturer Keysight Technologies IncDescription PSG RF Analog Signal GeneratorSerial Number MY53401535Customer Asset No. E8663D01535 Date of Calibration 30 Jan 2019Procedure TME-N7820A-E.16.05Temperature (23 ± 5) °CHumidity (50 ± 30) %RH

CustomerKeysight Technologies Inc 10090 Foothills Blvd ROSEVILLE CA 95747 United States

Location of Calibration

Keysight Technologies Inc 10090 Foothills Blvd. Roseville CA 95747-7102 UNITED STATES

This certifies that the equipment has been calibrated using applicable Keysight Technologies procedures and in compliance with ISO/IEC17025:2017 and ANSI/NCSL Z540.3-2006. The quality management system is registered to ISO 9001:2015. As Received ConditionsThe measured values of the equipment were observed in specification at the points tested. Additionally, the expanded measurementuncertainty intervals about the measured values were in specification. Action Taken- No corrective actions were necessary. As Completed ConditionsThe measured values of the equipment were observed in specification at the points tested. Additionally, the expanded measurementuncertainty intervals about the measured values were in specification. Remarks or Special Requirements This calibration certificate may refer to instruments manufactured by HP, Agilent and Keysight as being manufactured by KeysightTechnologies, Inc. The test limits stated in the report correspond to the published specifications of the equipment, at the points tested. Based on the customer's request, the next calibration is due on 30 Jan 2021.

Keysight Technologies Inc10090 Foothills Blvd.Roseville CA 95747-7102UNITED STATES Wes Fischbach Roseville Serv. Cntr. Mgr.

Issue Date 31 Jan 2019 Page 1 of 56



Traceability Information

Technician ID Number 01007027 Measurements are traceable to the International System of Units (SI) via national metrology institutes (www.keysight.com/find/NMI) thatare signatories to the CIPM Mutual Recognition Arrangement. This certificate shall not be reproduced, except in full, without prior written approval of the laboratory.

Calibration Equipment Used

Model Number Model Description Equipment ID Cal Due Date53132A Universal Counter, 225 MHz, 12 digit/s, 150 ps.

GPIB, RS23253132A02243 5 Nov 2019

53181A RF Counter, 225 MHz, 10 digit/s. GPIB, RS232 53181A05755 17 Jan 2020Datum 8040 Rubidium Frequency Standard 8040C04021 7 May 2019E4419B Power meter - EPM series, dual channel E4419B60686 21 Sep 2019E4448A PSA Spectrum Analyzer 3 Hz - 50 GHz E4448A20337 25 Jun 2020E8257D PSG analog signal generator E8257D20023 23 Jul 2020E9304A Power Sensor-Average, 9 kHz to 6 GHz, -60 to +20

dBmE9304A96846 13 Sep 2019

N5500A Phase noise test set N5500A01172 15 Mar 2019N5507A Low noise 26.5 GHz microwave downconverter N5507A01131 12 Mar 2019N9020A MXA Signal Analyzer N9020A20126 28 Mar 2019

Traceability Table

Model Model Description Equipment ID Certificate Number Trace ValueW,R 53132A Universal Counter, 225 MHz, 12 digit/

s, 150 ps. GPIB, RS23253132A02243 1-10535770140-1-ANAB:AC-1498 Frequency

W,R 53181A RF Counter, 225 MHz, 10 digit/s.GPIB, RS232

53181A05755 1-9600485871-1-ANAB:AC-1498 Frequency

W,R Datum 8040 Rubidium Frequency Standard 8040C04021 1-9783888205-1-ANAB:AC-1498 FrequencyW,R E4419B Power meter - EPM series, dual

channelE4419B60686 1-9222325679-1-ANAB :AC-1498 RF Power

W,R E4448A PSA Spectrum Analyzer 3 Hz - 50GHz

E4448A20337 1-10783202120-1-ANAB:AC-1498 AttenuationRF PowerSpectral Purity

W,R E8257D PSG analog signal generator E8257D20023 1-10207041822-1-ANAB:AC-1498 AmplitudeModulationFrequencyFrequencyModulationPhase ModulationPhase NoiseRF PowerSpectral Purity

Page 2 of 56



Model Model Description Equipment ID Certificate Number Trace ValueW,R E9304A Power Sensor-Average, 9 kHz to 6

GHz, -60 to +20 dBmE9304A96846 1-10380712845-1-ANAB:AC-1498 RF Power

W,R N5500A Phase noise test set N5500A01172 1-9216231112-1-ANAB :AC-1498 Phase NoiseW,R N5507A Low noise 26.5 GHz microwave

downconverterN5507A01131 1-9744487780-1-ANAB:AC-1498 Phase Noise

W,R N9020A MXA Signal Analyzer N9020A20126 1-8767980615-1-ANAB :AC-1498 AttenuationRF Power

Legend

W - Working Standard The calibration equipment used for the calibration of the Model indicated on the first page of the Certificate ofcalibration.R - Reference Standard The Reference Standard (Accredited or NMI-calibrated ETE) used to provide traceability to the SI-Units forthe calibration parameters listed.

Page 3 of 56



Compliance with Specification

The uncertainty of measurement has been taken into account when determining compliance with specification, as per ILAC-G8:03/2009.If the expanded measurement uncertainty intervals centered about one or more measured values were both in as well as out of specification(upper or lower), it is not possible to state compliance or non-compliance based on a 95% coverage probability for the expandedmeasurement uncertainty. An overall statement of compliance for all tests performed as received, and as completed (if any adjustments / repairs were performed) isincluded at the beginning of this report. Statements of compliance apply only to warranted specifications. When functional verification testsare performed, results are reported in the “Functional Test” section, and do not affect these statements of compliance.The status summaries relate to the tested item only. A final decision about whether the item's performance actually satisfies requirements ofthe user can only be made by the user.

Measurement results are reported as:

• Passed ( ) - The measured values of the equipment were observed in specification at the points tested. Additionally, the expandedmeasurement uncertainty intervals about the measured values were in specification.

• Undetermined (U) - The expanded measurement uncertainty intervals about one or more measured values were in as well as out ofspecification. Consequently, neither compliance nor non-compliance with specification can be declared based on thestated coverage probability.

• Failed (F) - One or more measured values of the equipment were observed out of specification at the points tested. Additionally, theexpanded measurement uncertainty intervals about one or more measured values were entirely outside the specification.

Upper Specification

Nominal

Lower Specification

Measurement Result Passed ( ) Undetermined (U) Undetermined (U) Failed (F)

( ) This result is indicated on the measurement report as a blank space in the column labeled “Status” or “Sts”.MU = 95% expanded measurement uncertainty.

Acceptance Limit

The "Keysight Cal + Uncertainties + Guardbanding" service employs a guard band in the amount of the 95% expanded measurementuncertainty (MU). The resulting acceptance limit applied for Pass or Fail decisions, and for performing adjustments, is the difference of thespecification and the guard band. Uncertainty of Measurement

The uncertainty evaluation has been performed in accordance with ISO/IEC Guide 98-3:2008 (GUM). The reported expanded uncertaintyof measurement is stated as the standard uncertainty of measurement multiplied by the coverage factor k such that the coverage probabilitycorresponds to approximately 95%. This probability corresponds to a coverage factor of k=2 for a normal distribution.

Page 4 of 56



Calibration Test Results Summary

Test Name As Received StatusMaximum Output Power PassedPower Level Accuracy PassedHarmonic Spurious PassedNon-Harmonic Spurious PassedSingle-Sideband Phase Noise PassedResidual Phase Noise PassedInternal Timebase Offset Passed

Functional Test Results Summary

The following functional test results are not part of an accredited delivery, even if they are part of an otherwise accredited calibration report.

The following tests document the functional verification of the instruments’ non-warranted performance. Neither a statement ofconformance or decision rule is used for a Functional Test, measurement uncertainties are only provided by exception. For a “FunctionalTest” the test results are reported as "As Expected" when showing expected performance and "Not As Expected" otherwise. "As Expected"results of individual test points are indicated in the measurement report by a blank space in the column labeled "Status" to allow easierrecognition of any "Not As Expected" points. If a functional test result is reported as "Not As Expected", repair and/or adjustment isrecommended. Test results reported as “Done” are possible if no limits are applied. For qualitative or quantitative “Functional Tests” the testresults are not warranted, and no judgment is made. The “actual” measured results are helpful to users for some applications.

Test Name As Received StatusSelf Check As Expected

Tested ConfigurationFirmware Version C.06.22

Tested Options 1E1 1EH 509 U04 UNX

Page 5 of 56

Measurement Report Certificate Number 1-10824024277-1

Model E8663D Serial MY53401535 Firmware Rev C.06.22Options Tested 1E1 1EH 509 U04 UNX

Test Date 30 Jan 2019Condition As Received

Maximum Output Power Passed

Harmonics Filter = Off

Frequency Minimum Measured Uncert. Status 0.25 MHz 14.00 dBm 16.12 dBm 0.15 dB 1.00 MHz 14.00 dBm 16.03 dBm 0.15 dB 10.10 MHz 15.00 dBm 16.08 dBm 0.15 dB 100.00 MHz 15.00 dBm 16.10 dBm 0.15 dB 800.00 MHz 15.00 dBm 16.11 dBm 0.16 dB 900.00 MHz 15.00 dBm 16.12 dBm 0.16 dB 1000.00 MHz 15.00 dBm 16.11 dBm 0.16 dB 1500.00 MHz 15.00 dBm 16.11 dBm 0.16 dB 1800.00 MHz 15.00 dBm 16.20 dBm 0.16 dB 1900.00 MHz 15.00 dBm 16.18 dBm 0.16 dB 2000.00 MHz 15.00 dBm 16.16 dBm 0.16 dB 2400.00 MHz 15.00 dBm 16.02 dBm 0.16 dB 2500.00 MHz 15.00 dBm 16.03 dBm 0.16 dB 2700.00 MHz 15.00 dBm 16.02 dBm 0.16 dB 2900.00 MHz 15.00 dBm 16.03 dBm 0.16 dB 3200.00 MHz 15.00 dBm 16.04 dBm 0.16 dB 3300.00 MHz 14.00 dBm 16.03 dBm 0.16 dB 4000.00 MHz 14.00 dBm 16.05 dBm 0.16 dB 5000.00 MHz 14.00 dBm 16.04 dBm 0.17 dB 6000.00 MHz 14.00 dBm 16.03 dBm 0.17 dB 7000.00 MHz 14.00 dBm 16.02 dBm 0.17 dB

Page 6 of 56




Maximum Output Power (cont.)Frequency Minimum Measured Uncert. Status

8000.00 MHz 14.00 dBm 16.03 dBm 0.17 dB 9000.00 MHz 14.00 dBm 15.97 dBm 0.17 dB 1.00 MHz 15.00 dBm 16.77 dBm 0.15 dB 10.10 MHz 15.00 dBm 16.90 dBm 0.15 dB 100.00 MHz 15.00 dBm 16.70 dBm 0.15 dB 250.00 MHz 15.00 dBm 16.49 dBm 0.16 dB

Harmonics Filter = On

Frequency Minimum Measured Uncert. Status 10.10 MHz 15.00 dBm 16.17 dBm 0.15 dB 100.00 MHz 15.00 dBm 16.12 dBm 0.15 dB 800.00 MHz 15.00 dBm 16.14 dBm 0.16 dB 900.00 MHz 15.00 dBm 16.19 dBm 0.16 dB 1000.00 MHz 15.00 dBm 16.19 dBm 0.16 dB 1500.00 MHz 15.00 dBm 16.18 dBm 0.16 dB 1800.00 MHz 15.00 dBm 16.16 dBm 0.16 dB 1900.00 MHz 15.00 dBm 16.18 dBm 0.16 dB 2000.00 MHz 15.00 dBm 16.17 dBm 0.16 dB 10.10 MHz 11.00 dBm 15.17 dBm 0.15 dB 100.00 MHz 11.00 dBm 14.85 dBm 0.15 dB 250.00 MHz 11.00 dBm 14.06 dBm 0.15 dB

Page 7 of 56




Power Level Accuracy Passed

Test Power = -90.00 dBm, Analog, Harmonic Filter = Off, Low Phase Noise Mode = Off

Frequency Minimum Measured Maximum Uncert. Status 195.10 MHz −0.80 dB 0.23 dB 0.80 dB 0.22 dB 250.10 MHz −0.80 dB 0.24 dB 0.80 dB 0.22 dB 455.10 MHz −0.80 dB 0.24 dB 0.80 dB 0.22 dB 505.10 MHz −0.80 dB 0.22 dB 0.80 dB 0.22 dB 905.10 MHz −0.80 dB 0.23 dB 0.80 dB 0.22 dB 1050.10 MHz −0.80 dB 0.21 dB 0.80 dB 0.22 dB 1980.10 MHz −0.80 dB 0.19 dB 0.80 dB 0.22 dB 2050.00 MHz −1.00 dB 0.10 dB 1.00 dB 0.22 dB 2550.10 MHz −1.00 dB 0.09 dB 1.00 dB 0.22 dB 2850.10 MHz −1.00 dB 0.11 dB 1.00 dB 0.22 dB 3150.10 MHz −1.00 dB 0.16 dB 1.00 dB 0.23 dB 3250.10 MHz −1.00 dB 0.17 dB 1.00 dB 0.23 dB 4000.10 MHz −1.00 dB 0.13 dB 1.00 dB 0.23 dB 8050.10 MHz −1.00 dB 0.07 dB 1.00 dB 0.24 dB 8950.10 MHz −1.00 dB 0.07 dB 1.00 dB 0.24 dB

Page 8 of 56




Power Level Accuracy (cont.)



Page 9 of 56







Page 10 of 56







Page 11 of 56







Page 12 of 56







Page 13 of 56







Page 14 of 56







Page 15 of 56







Page 16 of 56







Page 17 of 56







Page 18 of 56







Page 19 of 56







Page 20 of 56







Page 21 of 56







Page 22 of 56







Page 23 of 56







Page 24 of 56







Page 25 of 56





Test Power = 0.00 dBm, Analog, Harmonic Filter = Off, Low Phase Noise Mode = Off

Frequency Minimum Measured Maximum Uncert. Status 0.30 MHz −0.60 dB 0.14 dB 0.60 dB 0.056 dB 0.70 MHz −0.60 dB 0.13 dB 0.60 dB 0.056 dB 0.90 MHz −0.60 dB 0.14 dB 0.60 dB 0.056 dB 95.10 MHz −0.60 dB 0.18 dB 0.60 dB 0.054 dB 195.10 MHz −0.60 dB 0.18 dB 0.60 dB 0.055 dB 250.10 MHz −0.60 dB 0.18 dB 0.60 dB 0.055 dB 305.10 MHz −0.60 dB 0.17 dB 0.60 dB 0.056 dB 455.10 MHz −0.60 dB 0.16 dB 0.60 dB 0.056 dB 505.10 MHz −0.60 dB 0.17 dB 0.60 dB 0.056 dB 705.10 MHz −0.60 dB 0.15 dB 0.60 dB 0.055 dB 905.10 MHz −0.60 dB 0.15 dB 0.60 dB 0.054 dB 1050.10 MHz −0.60 dB 0.14 dB 0.60 dB 0.054 dB 1500.10 MHz −0.60 dB 0.16 dB 0.60 dB 0.055 dB 1800.10 MHz −0.60 dB 0.19 dB 0.60 dB 0.055 dB 1980.10 MHz −0.60 dB 0.15 dB 0.60 dB 0.055 dB 2050.00 MHz −0.80 dB 0.04 dB 0.80 dB 0.056 dB 2550.10 MHz −0.80 dB 0.05 dB 0.80 dB 0.058 dB 2650.10 MHz −0.80 dB 0.05 dB 0.80 dB 0.058 dB 2850.10 MHz −0.80 dB 0.05 dB 0.80 dB 0.059 dB 3150.10 MHz −0.80 dB 0.05 dB 0.80 dB 0.060 dB 3250.10 MHz −0.80 dB 0.09 dB 0.80 dB 0.061 dB 4000.10 MHz −0.80 dB 0.11 dB 0.80 dB 0.065 dB 5000.10 MHz −0.80 dB 0.08 dB 0.80 dB 0.080 dB

Page 26 of 56




Power Level Accuracy (cont.)Frequency Minimum Measured Maximum Uncert. Status

6350.10 MHz −0.80 dB 0.06 dB 0.80 dB 0.087 dB 8050.10 MHz −0.80 dB 0.05 dB 0.80 dB 0.090 dB 8950.10 MHz −0.80 dB 0.00 dB 0.80 dB 0.090 dB


Frequency Minimum Measured Maximum Uncert. Status 195.10 MHz −0.60 dB 0.15 dB 0.60 dB 0.13 dB 250.10 MHz −0.60 dB 0.15 dB 0.60 dB 0.13 dB 455.10 MHz −0.60 dB 0.11 dB 0.60 dB 0.13 dB 505.10 MHz −0.60 dB 0.13 dB 0.60 dB 0.13 dB 905.10 MHz −0.60 dB 0.10 dB 0.60 dB 0.13 dB 1050.10 MHz −0.60 dB 0.11 dB 0.60 dB 0.13 dB 1980.10 MHz −0.60 dB 0.12 dB 0.60 dB 0.14 dB 2050.00 MHz −0.80 dB 0.01 dB 0.80 dB 0.13 dB 2550.10 MHz −0.80 dB 0.00 dB 0.80 dB 0.13 dB 2850.10 MHz −0.80 dB 0.00 dB 0.80 dB 0.13 dB 3150.10 MHz −0.80 dB 0.02 dB 0.80 dB 0.13 dB 3250.10 MHz −0.80 dB 0.02 dB 0.80 dB 0.13 dB 4000.10 MHz −0.80 dB 0.04 dB 0.80 dB 0.14 dB 8050.10 MHz −0.80 dB 0.00 dB 0.80 dB 0.15 dB 8950.10 MHz −0.80 dB −0.04 dB 0.80 dB 0.15 dB

Page 27 of 56






Frequency Minimum Measured Maximum Uncert. Status 3250.10 MHz −0.80 dB 0.02 dB 0.80 dB 0.16 dB 4000.10 MHz −0.80 dB 0.05 dB 0.80 dB 0.16 dB 8050.10 MHz −0.80 dB 0.03 dB 0.80 dB 0.17 dB 8950.10 MHz −0.80 dB −0.03 dB 0.80 dB 0.17 dB

Page 28 of 56






Frequency Minimum Measured Maximum Uncert. Status 195.10 MHz −0.60 dB 0.14 dB 0.60 dB 0.15 dB 250.10 MHz −0.60 dB 0.12 dB 0.60 dB 0.15 dB 455.10 MHz −0.60 dB 0.13 dB 0.60 dB 0.15 dB 505.10 MHz −0.60 dB 0.16 dB 0.60 dB 0.15 dB 905.10 MHz −0.60 dB 0.13 dB 0.60 dB 0.16 dB 1050.10 MHz −0.60 dB 0.12 dB 0.60 dB 0.16 dB 1980.10 MHz −0.60 dB 0.17 dB 0.60 dB 0.16 dB 2050.00 MHz −0.80 dB 0.01 dB 0.80 dB 0.16 dB 2550.10 MHz −0.80 dB 0.02 dB 0.80 dB 0.16 dB 2850.10 MHz −0.80 dB 0.03 dB 0.80 dB 0.16 dB 3150.10 MHz −0.80 dB 0.04 dB 0.80 dB 0.16 dB

Test Power = -90.00 dBm, Analog, Harmonic Filter = On, Low Phase Noise Mode = On

Frequency Minimum Measured Maximum Uncert. Status 195.10 MHz −0.80 dB 0.24 dB 0.80 dB 0.22 dB



Page 29 of 56




Power Level Accuracy (cont.)Test Power = -80.00 dBm, Analog, Harmonic Filter = On, Low Phase Noise Mode = On


















Page 30 of 56




Power Level Accuracy (cont.)Test Power = -35.00 dBm, Analog, Harmonic Filter = On, Low Phase Noise Mode = On














Test Power = 0.00 dBm, Analog, Harmonic Filter = On, Low Phase Noise Mode = On

Frequency Minimum Measured Maximum Uncert. Status 95.10 MHz −0.60 dB 0.18 dB 0.60 dB 0.054 dB 195.10 MHz −0.60 dB 0.19 dB 0.60 dB 0.055 dB

Test Power = 5.00 dBm, Analog, Harmonic Filter = On, Low Phase Noise Mode = On


Page 31 of 56




Power Level Accuracy (cont.)Test Power = 11.00 dBm, Analog, Harmonic Filter = On, Low Phase Noise Mode = On


Harmonic Spurious Passed

2nd Harmonic, Harmonic Filter Off

Fundamental Frequency Harmonic Frequency Measured Maximum Uncert. Status 1.001 MHz 2.002 MHz −32.41 dBc −25.00 dBc 0.89 dB 10.001 MHz 20.002 MHz −35.89 dBc −28.00 dBc 0.89 dB 100.001 MHz 200.002 MHz −58.68 dBc −30.00 dBc 0.89 dB 250.001 MHz 500.002 MHz −40.03 dBc −30.00 dBc 0.89 dB 475.000 MHz 950.000 MHz −36.57 dBc −30.00 dBc 0.89 dB 500.001 MHz 1000.002 MHz −35.33 dBc −30.00 dBc 0.89 dB 700.000 MHz 1400.000 MHz −38.07 dBc −30.00 dBc 0.89 dB 900.000 MHz 1800.000 MHz −38.19 dBc −30.00 dBc 0.89 dB 1000.001 MHz 2000.002 MHz −35.48 dBc −30.00 dBc 1.0 dB 1800.000 MHz 3600.000 MHz −44.56 dBc −30.00 dBc 1.0 dB 2000.000 MHz 4000.000 MHz −79.44 dBc −30.00 dBc 1.1 dB 2000.001 MHz 4000.002 MHz −79.49 dBc −55.00 dBc 1.2 dB 2500.000 MHz 5000.000 MHz −87.57 dBc −55.00 dBc 1.3 dB 3200.000 MHz 6400.000 MHz −78.07 dBc −55.00 dBc 1.2 dB 3200.001 MHz 6400.002 MHz −77.61 dBc −55.00 dBc 1.2 dB

Page 32 of 56




Harmonic Spurious (cont.)Fundamental Frequency Harmonic Frequency Measured Maximum Uncert. Status

3900.000 MHz 7800.000 MHz −79.28 dBc −55.00 dBc 1.3 dB 4500.000 MHz 9000.000 MHz −78.70 dBc −55.00 dBc 1.3 dB

3rd Harmonic, Harmonic Filter Off

Fundamental Frequency Harmonic Frequency Measured Maximum Uncert. Status 1.001 MHz 3.003 MHz −44.26 dBc −25.00 dBc 0.89 dB 10.001 MHz 30.003 MHz −51.01 dBc −28.00 dBc 0.89 dB 100.001 MHz 300.003 MHz −73.88 dBc −30.00 dBc 0.90 dB 250.001 MHz 750.003 MHz −61.50 dBc −30.00 dBc 0.89 dB 475.000 MHz 1425.000 MHz −56.30 dBc −30.00 dBc 0.89 dB 500.001 MHz 1500.003 MHz −56.02 dBc −30.00 dBc 0.89 dB 700.000 MHz 2100.000 MHz −61.89 dBc −30.00 dBc 1.0 dB 900.000 MHz 2700.000 MHz −65.97 dBc −30.00 dBc 1.0 dB 1000.001 MHz 3000.003 MHz −51.83 dBc −30.00 dBc 1.0 dB 1800.000 MHz 5400.000 MHz −83.26 dBc −30.00 dBc 1.1 dB 2000.000 MHz 6000.000 MHz −83.44 dBc −30.00 dBc 1.1 dB 2000.001 MHz 6000.003 MHz −83.66 dBc −55.00 dBc 1.2 dB 2500.000 MHz 7500.000 MHz −83.37 dBc −55.00 dBc 1.4 dB

Page 33 of 56




Harmonic Spurious (cont.)

2nd Harmonic, Harmonic Filter On

Fundamental Frequency Harmonic Frequency Measured Maximum Uncert. Status 10.001 MHz 20.002 MHz −72.60 dBc −45.00 dBc 0.89 dB 100.001 MHz 200.002 MHz −69.28 dBc −55.00 dBc 0.89 dB 250.001 MHz 500.002 MHz −72.13 dBc −55.00 dBc 0.89 dB 475.000 MHz 950.000 MHz −74.83 dBc −55.00 dBc 0.90 dB 500.001 MHz 1000.002 MHz −65.03 dBc −55.00 dBc 0.89 dB 700.000 MHz 1400.000 MHz −78.46 dBc −55.00 dBc 0.91 dB 900.000 MHz 1800.000 MHz −72.89 dBc −55.00 dBc 0.90 dB 1000.001 MHz 2000.002 MHz −66.78 dBc −55.00 dBc 1.0 dB 1800.000 MHz 3600.000 MHz −74.52 dBc −55.00 dBc 1.0 dB 2000.000 MHz 4000.000 MHz −78.66 dBc −55.00 dBc 1.1 dB

Page 34 of 56




Harmonic Spurious (cont.)

3rd Harmonic, Harmonic Filter On

Fundamental Frequency Harmonic Frequency Measured Maximum Uncert. Status 10.001 MHz 30.003 MHz −77.91 dBc −45.00 dBc 0.91 dB 100.001 MHz 300.003 MHz −93.94 dBc −55.00 dBc 1.4 dB 250.001 MHz 750.003 MHz −85.54 dBc −55.00 dBc 1.0 dB 475.000 MHz 1425.000 MHz −83.61 dBc −55.00 dBc 0.97 dB 500.001 MHz 1500.003 MHz −98.57 dBc −55.00 dBc 2.1 dB 700.000 MHz 2100.000 MHz −88.13 dBc −55.00 dBc 1.2 dB 900.000 MHz 2700.000 MHz −97.60 dBc −55.00 dBc 2.2 dB 1000.001 MHz 3000.003 MHz −88.58 dBc −55.00 dBc 1.2 dB 1800.000 MHz 5400.000 MHz −83.88 dBc −55.00 dBc 1.1 dB 2000.000 MHz 6000.000 MHz −83.49 dBc −55.00 dBc 1.1 dB

Non-Harmonic Spurious PassedPower Supply Spurs, Low Phase Noise Mode Off

Fundamental Frequency Spurious Frequency Measured Maximum Uncert. Status 100.000 MHz 100.103 MHz −110.62 dBc −58.00 dBc 1.6 dB 500.000 MHz 500.103 MHz −110.21 dBc −80.00 dBc 1.6 dB 2000.000 MHz 2000.103 MHz −108.54 dBc −74.00 dBc 1.4 dB 3200.000 MHz 3200.103 MHz −108.57 dBc −68.00 dBc 2.3 dB 8900.000 MHz 8900.103 MHz −102.75 dBc −62.00 dBc 1.4 dB

Page 35 of 56




Non-Harmonic Spurious (cont.)Power Supply Spurs, Low Phase Noise Mode On

Fundamental Frequency Spurious Frequency Measured Maximum Uncert. Status 100.000 MHz 100.103 MHz −109.92 dBc −80.00 dBc 1.3 dB

Sampler Spurs, Low Phase Noise Mode Off

Fundamental Frequency Spurious Frequency Measured Maximum Uncert. Status 3698.724 MHz 3698.857 MHz −91.20 dBc −62.00 dBc 0.76 dB 4585.247 MHz 4585.380 MHz −99.07 dBc −62.00 dBc 1.7 dB 5907.122 MHz 5907.255 MHz −105.04 dBc −62.00 dBc 3.0 dB 5989.739 MHz 5989.872 MHz −97.56 dBc −62.00 dBc 1.5 dB 6031.048 MHz 6031.181 MHz −111.56 dBc −62.00 dBc 4.8 dB 7231.286 MHz 7231.419 MHz −102.99 dBc −62.00 dBc 2.5 dB 8130.698 MHz 8130.831 MHz −104.95 dBc −62.00 dBc 3.1 dB 8142.342 MHz 8142.474 MHz −98.55 dBc −62.00 dBc 1.7 dB 8490.226 MHz 8490.359 MHz −91.12 dBc −62.00 dBc 0.80 dB

Frac N 250 MHz Crossing Spurs, Low Phase Noise Mode Off

Fundamental Frequency Spurious Frequency Measured Maximum Uncert. Status 7661.311 MHz 7661.444 MHz −106.88 dBc −62.00 dBc 3.6 dB 7661.787 MHz 7661.920 MHz −99.05 dBc −62.00 dBc 1.7 dB 7663.869 MHz 7664.002 MHz −108.36 dBc −62.00 dBc 4.0 dB 7665.431 MHz 7665.564 MHz −100.88 dBc −62.00 dBc 2.1 dB 7666.993 MHz 7667.126 MHz −106.44 dBc −62.00 dBc 3.4 dB 7672.201 MHz 7672.334 MHz −108.60 dBc −62.00 dBc 4.1 dB 7676.368 MHz 7676.501 MHz −97.09 dBc −62.00 dBc 1.4 dB

IF 250 MHz Crossing Spurs, Low Phase Noise Mode Off

Fundamental Frequency Spurious Frequency Measured Maximum Uncert. Status 6046.282 MHz 6046.415 MHz −86.84 dBc −62.00 dBc 0.50 dB 6066.794 MHz 6066.927 MHz −95.89 dBc −62.00 dBc 1.3 dB 7403.312 MHz 7403.445 MHz −85.66 dBc −62.00 dBc 0.45 dB 7429.683 MHz 7429.816 MHz −108.15 dBc −62.00 dBc 3.9 dB 7798.820 MHz 7798.953 MHz −85.33 dBc −62.00 dBc 0.45 dB 7825.191 MHz 7825.324 MHz −100.99 dBc −62.00 dBc 2.1 dB 8220.699 MHz 8220.832 MHz −100.37 dBc −62.00 dBc 2.0 dB 8376.559 MHz 8376.692 MHz −105.58 dBc −62.00 dBc 3.2 dB 8660.152 MHz 8660.285 MHz −99.94 dBc −62.00 dBc 1.9 dB 8816.012 MHz 8816.145 MHz −105.43 dBc −62.00 dBc 3.3 dB

Offset Reference Spurs, Low Phase Noise Mode Off

Fundamental Frequency Spurious Frequency Measured Maximum Uncert. Status 80.000 MHz 60.000 MHz −115.44 dBc −58.00 dBc 2.7 dB 80.000 MHz 70.000 MHz −103.13 dBc −58.00 dBc 1.1 dB 80.000 MHz 90.000 MHz −102.92 dBc −58.00 dBc 1.1 dB

Page 36 of 56




Non-Harmonic Spurious (cont.)Fundamental Frequency Spurious Frequency Measured Maximum Uncert. Status

80.000 MHz 100.000 MHz −121.17 dBc −58.00 dBc 3.5 dB 980.000 MHz 960.000 MHz −121.97 dBc −80.00 dBc 3.4 dB 980.000 MHz 970.000 MHz −118.11 dBc −80.00 dBc 2.9 dB 980.000 MHz 990.000 MHz −110.72 dBc −80.00 dBc 1.6 dB 980.000 MHz 1000.000 MHz −122.45 dBc −80.00 dBc 3.4 dB 1980.000 MHz 1960.000 MHz −128.80 dBc −74.00 dBc 3.6 dB 1980.000 MHz 1970.000 MHz −122.29 dBc −74.00 dBc 3.5 dB 1980.000 MHz 1990.000 MHz −109.54 dBc −74.00 dBc 1.7 dB 1980.000 MHz 2000.000 MHz −125.85 dBc −74.00 dBc 3.6 dB 3180.000 MHz 3160.000 MHz −126.27 dBc −68.00 dBc 3.6 dB 3180.000 MHz 3170.000 MHz −115.73 dBc −68.00 dBc 3.5 dB 3180.000 MHz 3190.000 MHz −116.99 dBc −68.00 dBc 3.6 dB 3180.000 MHz 3200.000 MHz −121.41 dBc −68.00 dBc 3.6 dB 8980.000 MHz 8960.000 MHz −120.64 dBc −62.00 dBc 3.6 dB 8980.000 MHz 8970.000 MHz −113.04 dBc −62.00 dBc 3.4 dB 8980.000 MHz 8990.000 MHz −108.51 dBc −62.00 dBc 2.7 dB 8980.000 MHz 9000.000 MHz −123.48 dBc −62.00 dBc 3.6 dB

Offset Reference Spurs, Low Phase Noise Mode On

FundamentalFrequency Spurious Frequency Measured Maximum Uncert. Status

80.000 MHz 60.000 MHz −125.76 dBc −80.00 dBc 3.6 dB 80.000 MHz 70.000 MHz −113.10 dBc −80.00 dBc 1.9 dB 80.000 MHz 90.000 MHz −113.39 dBc −80.00 dBc 2.0 dB 80.000 MHz 100.000 MHz −124.39 dBc −80.00 dBc 3.5 dB

Clock Spurs, Low Phase Noise Mode Off

Fundamental Frequency Spurious Frequency Measured Maximum Uncert. Status 150.000 MHz 100.000 MHz −112.38 dBc −58.00 dBc 2.1 dB 200.000 MHz 233.554 MHz −123.83 dBc −58.00 dBc 3.6 dB 900.000 MHz 100.000 MHz −123.76 dBc −80.00 dBc 3.6 dB 950.000 MHz 983.554 MHz −129.85 dBc −80.00 dBc 3.6 dB 1950.000 MHz 1983.554 MHz −133.05 dBc −74.00 dBc 3.6 dB 3150.000 MHz 3183.554 MHz −124.40 dBc −68.00 dBc 3.6 dB 8900.000 MHz 100.000 MHz −123.13 dBc −62.00 dBc 3.6 dB 8950.000 MHz 8983.554 MHz −122.04 dBc −62.00 dBc 3.6 dB

Clock Spurs, Low Phase Noise Mode On

Fundamental Frequency Spurious Frequency Measured Maximum Uncert. Status 150.000 MHz 100.000 MHz −126.87 dBc −80.00 dBc 3.6 dB 200.000 MHz 233.554 MHz −123.51 dBc −80.00 dBc 3.6 dB

Page 37 of 56




Non-Harmonic Spurious (cont.)FracN Feedthru Spurs, Low Phase Noise Mode Off

Fundamental Frequency Spurious Frequency Measured Maximum Uncert. Status 1145.681 MHz 599.800 MHz −128.30 dBc −74.00 dBc 3.6 dB 1145.869 MHz 614.800 MHz −125.93 dBc −74.00 dBc 3.6 dB 1146.431 MHz 659.800 MHz −120.24 dBc −74.00 dBc 3.2 dB 1146.994 MHz 704.800 MHz −105.58 dBc −74.00 dBc 1.2 dB 1147.181 MHz 719.800 MHz −103.43 dBc −74.00 dBc 1.1 dB 1147.369 MHz 734.800 MHz −102.64 dBc −74.00 dBc 1.0 dB 1147.556 MHz 749.800 MHz −102.42 dBc −74.00 dBc 1.0 dB 2292.112 MHz 629.800 MHz −124.24 dBc −68.00 dBc 3.5 dB 2292.487 MHz 644.800 MHz −125.33 dBc −68.00 dBc 3.6 dB 2293.237 MHz 674.800 MHz −127.50 dBc −68.00 dBc 3.6 dB 2293.612 MHz 689.800 MHz −122.72 dBc −68.00 dBc 3.5 dB 2293.987 MHz 704.800 MHz −118.09 dBc −68.00 dBc 2.9 dB 2294.362 MHz 719.800 MHz −117.63 dBc −68.00 dBc 2.8 dB 2294.737 MHz 734.800 MHz −116.11 dBc −68.00 dBc 2.5 dB 2295.487 MHz 764.800 MHz −113.44 dBc −68.00 dBc 2.0 dB

Single-Sideband Phase Noise Passed

Carrier Frequency:100 MHz ModeLowPhaseNoise

CarrierFrequency Offset Test Mode Measured Max Uncert. Status

100 MHz 1 Hz ModeLowPhaseNoise −92.05 dBc/Hz −70.00 dBc/Hz 2.3 dB 100 MHz 10 Hz ModeLowPhaseNoise −118.34 dBc/Hz −97.00 dBc/Hz 2.3 dB 100 MHz 100 Hz ModeLowPhaseNoise −129.32 dBc/Hz −119.00 dBc/Hz 2.3 dB 100 MHz 1 kHz ModeLowPhaseNoise −147.95 dBc/Hz −130.00 dBc/Hz 2.3 dB

Page 38 of 56




Single-Sideband Phase Noise (cont.)

CarrierFrequency Offset Measured Max Uncert. Status

100 MHz 1 Hz −89.18 dBc/Hz −58.00 dBc/Hz 2.3 dB 100 MHz 10 Hz −112.01 dBc/Hz −87.00 dBc/Hz 2.3 dB 100 MHz 100 Hz −125.46 dBc/Hz −104.00 dBc/Hz 2.3 dB 100 MHz 1 kHz −131.94 dBc/Hz −121.00 dBc/Hz 2.3 dB 100 MHz 10 kHz −136.94 dBc/Hz −128.00 dBc/Hz 2.3 dB 100 MHz 100 kHz −137.10 dBc/Hz −130.00 dBc/Hz 2.3 dB

Page 39 of 56





Carrier Frequency Offset Measured Max Uncert. Status 255.1 MHz 1 Hz −77.53 dBc/Hz −61.00 dBc/Hz 2.3 dB 255.1 MHz 10 Hz −107.42 dBc/Hz −88.00 dBc/Hz 2.3 dB 255.1 MHz 100 Hz −119.90 dBc/Hz −108.00 dBc/Hz 2.3 dB 255.1 MHz 1 kHz −129.01 dBc/Hz −125.00 dBc/Hz 2.3 dB 255.1 MHz 10 kHz −140.72 dBc/Hz −132.00 dBc/Hz 2.3 dB 255.1 MHz 100 kHz −142.71 dBc/Hz −136.00 dBc/Hz 2.3 dB

Page 40 of 56






600 MHz 1 Hz −74.33 dBc/Hz −57.00 dBc/Hz 2.3 dB 600 MHz 10 Hz −98.65 dBc/Hz −84.00 dBc/Hz 2.3 dB 600 MHz 100 Hz −115.43 dBc/Hz −101.00 dBc/Hz 2.3 dB 600 MHz 1 kHz −128.97 dBc/Hz −121.00 dBc/Hz 2.3 dB 600 MHz 10 kHz −139.01 dBc/Hz −130.00 dBc/Hz 2.3 dB 600 MHz 100 kHz −138.92 dBc/Hz −130.00 dBc/Hz 2.3 dB

Page 41 of 56





CarrierFrequency Offset Measured Max Uncert. Status 1.8 GHz 1 Hz −66.41 dBc/Hz −51.00 dBc/Hz 2.3 dB 1.8 GHz 10 Hz −90.60 dBc/Hz −79.00 dBc/Hz 2.3 dB 1.8 GHz 100 Hz −104.70 dBc/Hz −96.00 dBc/Hz 2.3 dB 1.8 GHz 1 kHz −126.52 dBc/Hz −115.00 dBc/Hz 2.3 dB 1.8 GHz 10 kHz −130.51 dBc/Hz −124.00 dBc/Hz 2.3 dB 1.8 GHz 100 kHz −130.82 dBc/Hz −124.00 dBc/Hz 2.3 dB

Page 42 of 56






3.199 GHz 1 Hz −57.27 dBc/Hz −46.00 dBc/Hz 2.3 dB 3.199 GHz 10 Hz −86.14 dBc/Hz −74.00 dBc/Hz 2.3 dB 3.199 GHz 100 Hz −99.37 dBc/Hz −92.00 dBc/Hz 2.3 dB 3.199 GHz 1 kHz −120.57 dBc/Hz −111.00 dBc/Hz 2.3 dB 3.199 GHz 10 kHz −125.96 dBc/Hz −120.00 dBc/Hz 2.3 dB 3.199 GHz 100 kHz −125.64 dBc/Hz −120.00 dBc/Hz 2.3 dB

Page 43 of 56





CarrierFrequency Offset Measured Max Uncert. Status 9 GHz 1 Hz −50.10 dBc/Hz −37.00 dBc/Hz 2.3 dB 9 GHz 10 Hz −78.64 dBc/Hz −65.00 dBc/Hz 2.3 dB 9 GHz 100 Hz −90.78 dBc/Hz −81.00 dBc/Hz 2.3 dB 9 GHz 1 kHz −112.30 dBc/Hz −101.00 dBc/Hz 2.3 dB 9 GHz 10 kHz −117.68 dBc/Hz −110.00 dBc/Hz 2.3 dB 9 GHz 100 kHz −116.89 dBc/Hz −110.00 dBc/Hz 2.3 dB

Page 44 of 56




Residual Phase Noise Passed


100 MHz 10 Hz −115.31 dBc/Hz −100.00 dBc/Hz 2.3 dB 100 MHz 100 Hz −125.43 dBc/Hz −110.00 dBc/Hz 2.3 dB 100 MHz 1 kHz −130.78 dBc/Hz −120.00 dBc/Hz 2.3 dB 100 MHz 10 kHz −136.84 dBc/Hz −128.00 dBc/Hz 2.3 dB 100 MHz 100 kHz −137.31 dBc/Hz −130.00 dBc/Hz 2.3 dB

Page 45 of 56




Residual Phase Noise (cont.)


500 MHz 10 Hz −110.22 dBc/Hz −105.00 dBc/Hz 2.3 dB 500 MHz 100 Hz −120.37 dBc/Hz −115.00 dBc/Hz 2.3 dB 500 MHz 1 kHz −129.66 dBc/Hz −124.00 dBc/Hz 2.3 dB 500 MHz 10 kHz −139.84 dBc/Hz −132.00 dBc/Hz 2.3 dB 500 MHz 100 kHz −141.55 dBc/Hz −136.00 dBc/Hz 2.3 dB

Page 46 of 56





CarrierFrequency Offset Measured Max Uncert. Status 1 GHz 10 Hz −105.16 dBc/Hz −100.00 dBc/Hz 2.3 dB 1 GHz 100 Hz −113.74 dBc/Hz −110.00 dBc/Hz 2.3 dB 1 GHz 1 kHz −125.16 dBc/Hz −120.00 dBc/Hz 2.3 dB 1 GHz 10 kHz −135.79 dBc/Hz −130.00 dBc/Hz 2.3 dB 1 GHz 100 kHz −136.48 dBc/Hz −130.00 dBc/Hz 2.3 dB

Page 47 of 56





CarrierFrequency Offset Measured Max Uncert. Status 2 GHz 10 Hz −98.97 dBc/Hz −96.00 dBc/Hz 2.3 dB 2 GHz 100 Hz −111.43 dBc/Hz −104.00 dBc/Hz 2.3 dB 2 GHz 1 kHz −118.63 dBc/Hz −114.00 dBc/Hz 2.3 dB 2 GHz 10 kHz −130.32 dBc/Hz −124.00 dBc/Hz 2.3 dB 2 GHz 100 kHz −129.58 dBc/Hz −124.00 dBc/Hz 2.3 dB

Page 48 of 56





CarrierFrequency Offset Measured Max Uncert. Status 3.2 GHz 10 Hz −94.32 dBc/Hz −92.00 dBc/Hz 2.3 dB 3.2 GHz 100 Hz −105.29 dBc/Hz −100.00 dBc/Hz 2.3 dB 3.2 GHz 1 kHz −114.72 dBc/Hz −110.00 dBc/Hz 2.3 dB 3.2 GHz 10 kHz −125.57 dBc/Hz −120.00 dBc/Hz 2.3 dB 3.2 GHz 100 kHz −125.51 dBc/Hz −120.00 dBc/Hz 2.3 dB

Internal Timebase Offset PassedElapsed time after power-on: 50 h The relative frequency (Rel. Freq.) value below is the difference frequency (actual frequency minus nominal frequency) divided by the nominal frequency.

Timebase Actual Frequency Rel. Freq. Min Freq. Error Max Uncertainty Sts 10 MHz 9.99999952306 MHz −4.76940E-08 −0.50000 Hz −0.47694 Hz 0.50000 Hz 0.00016 Hz

NOTE: No adjustment needed

Self Check As ExpectedTest Group = ALC Board Tests

Test Name Minimum Measured Maximum Status +10V 9.50 10.00 10.50 +9V PTAT 7.00 8.58 11.00 −10V −10.50 −9.99 −9.50 ALC Current −1.70 0.04 2.30

Page 49 of 56




Self Check (cont.)Test Name Minimum Measured Maximum Status

ALC Mod 20 GHz Closed 0.00 0.89 6.00 ALC Mod 20 GHz Open −1.00 0.00 1.00 ALC Off −0.10 0.00 0.10 ALC Reference Part 1 −0.30 0.00 0.30 ALC Reference Part 2 −0.84 −0.54 −0.24 ALC Reference Part 3 0.24 0.55 0.84 HiBand/MaxOut −9.00 −0.45 1.00 HiBand/RF Off −1.00 0.00 1.00 Hiband-At Midpoint −0.10 0.01 0.10 Hiband-Under Midpoint −0.10 0.01 0.10 Integrator Railed Negative −11.00 −10.00 −4.00 Integrator Railed Positive 8.00 10.00 11.00 Integrator/RF Off −7.40 −7.10 −6.50 LoBand/RF Off −1.00 0.00 1.00 Lowband Modulation −10.00 4.91 10.00 LowBand/MaxOut −9.00 −0.29 1.00 Lowband-At Midpoint −0.10 0.01 0.10 Mod Level Part 1 4.00 7.98 9.00 Mod Level Part 2 4.00 8.70 9.25 Mod Level Part 3 4.00 7.26 9.00 Mod Level Part 4 4.00 6.49 9.00 Mod Level Part 5 4.00 9.47 10.00 Scalar Pulse Mod −2.50 −1.42 −0.50 Unlevel Indicator Part 1 1.00 1.00 1.00 Unlevel Indicator Part 2 0.00 0.00 0.00 Unlevel Indicator Part 3 0.00 0.00 1.00

Test Group = Analog ModGen Tests

Test Name Minimum Measured Maximum Status +10V node 9.90 10.00 10.10 +5V ref node 4.90 5.00 5.10 −10V node −10.10 −9.99 −9.90 −5V node −5.10 −5.00 −4.90 AM Offset Maximum 0.15 0.23 0.25 AM Offset Minimum −2.30 −2.21 −2.10 AM1 Path Loss 1.00 1.09 1.20 AM2 Path Loss 1.00 1.09 1.20 Ext1 Peak Maximum 0.67 0.73 0.90 Ext1 Peak Mimimum −2.00 −0.90 −0.70 Ext2 Peak Maximum 0.67 0.74 0.90 Ext2 Peak Minimum −2.00 −0.90 −0.70 FED Vref DAC Maximum 3.00 3.36 3.80 FED Vref DAC Minimum 0.70 0.78 0.90 FGEN1 Abus Zero 0.00 0.00 0.00 FGEN1 Max Output 1.90 2.16 2.20 FGEN1 Min Output −2.30 −2.17 −2.00 FGEN1 Offset Max 2.20 2.46 2.60 FGEN1 Offset Min −0.08 −0.07 −0.06 FGEN2 Abus Zero 0.00 0.00 0.00

Page 50 of 56





FGEN2 Max Output 1.90 2.17 2.20 FGEN2 Min Output −2.30 −2.17 −2.00 FGEN2 Offset Max 2.20 2.46 2.60 FGEN2 Offset Min −0.08 −0.07 −0.06 FM1 DC Gain 1.00 1.15 1.30 FM1 Max Negative Offset −0.16 −0.14 −0.08 FM1 Max Positive Offset 0.12 0.15 0.20 FM2 DC Gain 1.00 1.25 1.50 FM2 Max Negative Offset −0.02 −0.01 0.00 FM2 Max Positive Offset 0.00 0.01 0.02 High Perf Pulse Not Available. 0.00 0.00 0.00 IPG Locked 1.00 1.00 1.00 IPG Tune 0.10 1.52 2.30 LF Out Max Negative −8.40 −8.25 −7.80 LF Out Max Positive 7.80 8.25 8.40 Numeric Synth Clk Locked 1.00 1.00 1.00 Numeric Synth Tune 0.10 1.29 2.30 Pulse20 FED Maximum 1.60 1.91 3.20 Pulse20 FED Minimum 0.40 1.35 1.90 Pulse20 FED Out Disable −0.01 0.00 0.02 RED Vref DAC Maximum 3.00 3.36 3.80 RED Vref DAC Minimum 0.70 0.78 0.90 Std Pulse 2.00 2.58 2.90 Std Pulse Output Disable 4.80 5.17 5.30 Sync Out On 0.50 2.64 3.00 Video Out On 0.50 2.61 3.00

Test Group = CPU Bd Tests

Test Name Minimum Measured Maximum Status +10V Ref 9.90 10.00 10.10 +9V Ref 8.90 8.98 9.10 −5.2V Ref −5.30 −5.18 −4.85 −6V Ref −6.20 −5.98 −5.80

Test Group = FracN Tests

Test Name Minimum Measured Maximum Status +10V 9.90 10.00 10.10 1.55-2.4 GHz 0.50 2.84 13.50 1000 MHz tune voltage 17.70 21.75 23.20 1000 MHz VCO out 0.20 0.93 1.95 −10V −10.10 −10.03 −9.90 1-1.55 GHz 0.50 1.86 13.50 2.4-3.2 GHz 0.50 2.27 13.50 250-396 MHz 0.25 2.49 13.50 396-628 MHz 0.50 2.99 13.50 500 MHz tune voltage 3.00 4.13 4.80 500 MHz VCO out 0.50 2.24 3.60 628-1000 MHz 1.00 3.61 13.50

Page 51 of 56





750 MHz tune voltage 9.60 10.76 12.80 750 MHz VCO out 0.40 1.63 2.80 F/2 at 300.0742MHz out 3.00 3.63 4.40 Max scale loop gain −10.10 −9.99 −9.70 Min scale loop gain −0.02 0.00 0.02 Non-inverted mode 0.00 0.00 0.00 PLL lock @ 1 GHz 1.00 1.00 1.00 PLL Lock @ 500 MHz 1.00 1.00 1.00 PLL Lock @ 750 MHz 1.00 1.00 1.00

Test Group = LBF Bd Tests

Test Name Minimum Measured Maximum Status +10V Supply 8.00 9.99 12.00 +10VS Supply 8.00 9.99 12.00 +15V Supply 11.00 14.82 18.00 +3.3V Supply 2.00 3.46 4.00 +3.3VDF Supply 1.00 3.05 5.00 +5V Supply 3.00 5.10 7.00 1000-1500MHz Filter @1500MHz −13.00 −1.56 −0.10 1000-1500MHz Filter @2000MHz −0.50 0.00 0.50 10-14MHz Filter @14 MHz −13.00 −1.57 −0.10 10-14MHz Filter @20 MHz −0.50 0.00 0.50 105-146MHz Filter @146MHz −13.00 −1.56 −0.10 105-146MHz Filter @210MHz −0.50 0.00 0.50 −10V Supply −12.00 −9.98 −8.00 14-19MHz Filter @19 MHz −13.00 −1.57 −0.10 14-19MHz Filter @28 MHz −0.50 0.00 0.50 146-205MHz Filter @205MHz −13.00 −1.57 −0.10 146-205MHz Filter @292MHz −0.50 0.00 0.50 1500-2000MHz Filter @2000MHz −13.00 −1.54 −0.10 −15V Supply −18.00 −14.91 −11.00 19-27MHz Filter @27MHz −13.00 −1.57 −0.10 19-27MHz Filter @38MHz −0.50 0.00 0.50 2.5 GHz Bypass Path −13.00 −1.17 −0.10 205-250MHz Filter @250MHz −13.00 −1.57 −0.10 205-250MHz Filter @410MHz −0.50 0.00 0.50 250-396MHz Filter @396MHz −13.00 −1.59 −0.10 250-396MHz Filter @500MHz −0.50 −0.01 0.50 27-38MHz Filter @38MHz −13.00 −1.57 −0.10 27-38MHz Filter @54MHz −0.50 0.00 0.50 300 MHz Bypass Path −13.00 −1.57 −0.10 38-53MHz Filter @53MHz −13.00 −1.56 −0.10 38-53MHz Filter @76MHz −0.50 0.00 0.50 396-500MHz Filter @500MHz −13.00 −1.55 −0.10 396-500MHz Filter @792MHz −0.50 0.00 0.50 500-628MHz Filter @1000MHz −0.50 −0.01 0.50 500-628MHz Filter @628MHz −13.00 −1.55 −0.10 53-75MHz Filter @106MHz −0.50 0.00 0.50 53-75MHz Filter @75MHz −13.00 −1.56 −0.10

Page 52 of 56





−5V Supply −7.00 −5.00 −3.00 628-1000MHz Filter @1000MHz −13.00 −1.57 −0.10 628-1000MHz Filter @1236MHz −0.50 0.00 0.50 75-105MHz Filter @105MHz −13.00 −1.56 −0.10 75-105MHz Filter @150MHz −0.50 0.00 0.50 Analog Ground −0.50 0.00 0.50 Divider Test @10MHz 0.10 0.55 1.50 Divider Test @20MHz 0.10 0.56 1.50 Driver Amp Bias −4.00 −1.27 −0.10 Monotonicity Check 1.00 1.00 1.00 Power Amp 1 Bias −4.00 −1.04 −0.10 Power Amp 2 Bias −4.00 −1.05 −0.10 Pulse Modulator Off −13.00 −1.57 −0.10 Pulse Modulator On −0.50 0.01 0.50 Step Atten 1 0.50 0.85 1.50 Step Atten 16 12.00 16.01 19.00 Step Atten 2 1.00 2.00 3.00 Step Atten 4 3.00 4.04 5.00 Step Atten 8 5.00 8.00 10.00 Step Atten Reference @0 −2.00 0.00 2.00 Switched +10V Supply 8.00 9.93 12.00 Switched +10V Supply Off −1.00 −0.45 1.00 Switched +9V Supply 6.00 9.12 12.00 Switched +9V Supply Off −1.00 0.04 1.00 Switched -5V Supply −8.00 −4.73 −2.00 Switched -5V Supply Off −2.00 −1.13 −0.10 Test bad divide −5.00 −2.11 −0.50

Test Group = Lowband Bd Tests

Test Name Minimum Measured Maximum Status +10VP 9.00 10.00 11.00 +8Vsw Off −0.50 0.01 0.50 +8Vsw On 7.50 8.47 9.50 1000-1500MHz Filter @1499MHz −13.00 −2.18 −0.50 −10VP −11.00 −10.01 −9.00 1500-2400MHz Filter @2399MHz −13.00 −2.12 −0.50 250-396MHz Filter @395MHz −13.00 −3.19 −0.50 250-396MHz Filter @500MHz −0.50 −0.04 0.50 396-628MHz Filter @627MHz −13.00 −3.74 −0.50 396-628MHz Filter @792MHz −0.50 −0.06 0.50 628-1000MHz Filter @1256MHz −0.50 −0.02 0.50 628-1000MHz Filter @999MHz −13.00 −2.53 −0.10 ALC Mod Bias DAC @Max −13.00 −3.09 −0.50 ALC Mod Bias DAC @Min −0.50 −0.01 0.50 ALC Mod Offset DAC @Max −0.50 −0.01 0.50 ALC Mod Offset DAC @Min −13.00 −3.12 −0.50 Amp Bias Switch Off −0.50 −0.02 0.50 Amp Bias Switch On −4.50 −3.12 −0.50 Clamp Detector Test −4.00 −3.42 −0.50

Page 53 of 56





Ground voltage −0.50 0.03 0.50 Het band −13.00 −2.54 −0.50 Max current −13.00 −12.44 −8.00 Max Current −13.00 −12.44 −8.00 Min current 8.00 9.97 13.00 Min Current 8.00 9.92 13.00 Min Scale Prelevel −2.50 −0.56 −0.30 Nominal DAC settings −13.00 −2.64 −0.50 Power Limit DAC @Max −15.00 −0.38 15.00 Power Limit DAC @Min −0.50 −0.04 0.50 Prelevel cond 2 −0.50 −0.03 0.50 Temp Sense Voltage 6.00 7.65 11.00

Test Group = MID Bd Tests

Test Name Minimum Measured Maximum Status 12V Supply 11.50 11.91 12.50 3.5V Supply 3.00 3.48 3.70 −3V Supply −3.30 −3.14 −2.80 6.5V Supply 6.00 6.50 7.00 8V Supply 7.50 8.00 8.50 DBL20_8VSW_ABUS 7.00 7.86 8.50 DBL20_VD1_ABUS 6.00 7.08 7.80 DBL20_VD2_ABUS 6.00 7.08 7.80 DBL20_VD3_ABUS 6.00 7.07 7.80 DBL20_VD4_ABUS 6.00 7.11 7.80 HIBx10_ABUS @10GHz −9.00 −1.02 0.00 HIBx10_ABUS @12.8GHz −9.00 −1.07 0.00 HIBx10_ABUS @12.8GHz −9.00 −1.07 0.00 HIBx10_ABUS @2.01GHz −9.00 −0.92 0.00 HIBx10_ABUS @20GHz −9.00 −1.21 0.00 HIBx10_ABUS @2GHz −9.00 −0.94 0.00 HIBx10_ABUS @3.21GHz −9.00 −0.92 0.00 HIBx10_ABUS @3.2GHz −9.00 −0.92 0.00 HIBx10_ABUS @5GHz −9.00 −0.94 0.00 HIBx10_ABUS @8GHz −9.00 −1.00 0.00 Ig4(mA) @10GHz −8.00 3.88 5.00 Ig4(mA) @12.8GHz −8.00 2.31 5.00 Ig4(mA) @16GHz −8.00 1.66 5.00 Ig4(mA) @20GHz −8.00 −0.23 5.00 Ig4(mA) @3.21GHz −8.00 4.32 5.00 Ig4(mA) @5GHz −8.00 4.32 5.00 Ig4(mA) @8GHz −8.00 4.32 5.00 LOBx10_ABUS @2GHz −9.00 −0.91 0.00 Lowband Pulse Off −1.00 0.00 1.00 Lowband Pulse On −3.00 −1.13 0.00 MODF_12VSW_ABUS 11.00 11.67 12.50 MODF_9VSW_ABUS 8.00 8.95 9.50 MODF_VD1_ABUS 7.00 8.06 8.80 MODF_VD2_ABUS 10.00 10.85 11.80

Page 54 of 56





MODF_VD3_ABUS 10.00 10.85 11.80 MODF_VD4_ABUS 10.00 10.85 11.80 RF pulse off −1.00 0.00 1.00 RF pulse on −9.00 −0.93 0.00 SW_FAULT_ABUS @12GHz −8.00 −7.51 0.00 SW_FAULT_ABUS @12GHz −8.00 −7.51 0.00 SW_FAULT_ABUS @15GHz −8.00 −7.51 0.00 SW_FAULT_ABUS @15GHz −8.00 −7.52 0.00 SW_FAULT_ABUS @18GHz −8.00 −7.52 0.00 SW_FAULT_ABUS @4GHz −8.00 −7.51 0.00 SW_FAULT_ABUS @6GHz −8.00 −7.51 0.00 SW_FAULT_ABUS @9GHz −8.00 −7.52 0.00 U1 drain current(mA) 50.00 149.38 250.00 U1 Drain Current(mA) 50.00 295.20 350.00 U2 drain current(mA) 50.00 149.30 250.00 U2 Drain Current(mA) 50.00 414.85 500.00 U3 drain current(mA) 50.00 150.10 250.00 U3 Drain Current(mA) 50.00 412.20 500.00 U4 drain current(mA) 50.00 129.42 250.00 U4 Drain Current(mA) 50.00 413.34 500.00 VDET_ABUS @10GHz −10.00 −5.11 −1.00 VDET_ABUS @12.8GHz −10.00 −5.12 −1.00 VDET_ABUS @16GHz −10.00 −3.84 −1.00 VDET_ABUS @20GHz −10.00 −5.87 −1.00 VDET_ABUS @3.21GHz −10.00 −4.57 −1.00 VDET_ABUS @5GHz −10.00 −4.52 −1.00 VDET_ABUS @8GHz −10.00 −4.59 −1.00

Test Group = Reference Bd Tests

Test Name Minimum Measured Maximum Status +15V 1.30 1.38 1.50 +9V 0.80 0.82 0.90 100MHz Osc Tune Line −10.00 −0.03 10.00 100MHz Osc Unlock 0.00 0.00 0.00 100MHZ_TUNE0 0 −0.10 0.81 2.00 100MHZ_TUNE0 1 −0.10 0.81 2.00 100MHZ_TUNE0 2 −0.10 0.80 2.00 100MHZ_TUNE0 3 −0.10 0.80 2.00 100MHZ_TUNE0 4 −0.10 0.80 2.00 100MHZ_TUNE0 5 −0.10 0.80 2.00 100MHZ_TUNE0 6 −0.10 0.80 2.00 100MHZ_TUNE0 7 −0.10 0.80 2.00 −15V −1.50 −1.39 1.30 FracN Out 10MHz 0.00 1.32 1.50 Internal 10MHz 0.14 0.30 0.34 Lowband(Off) 1GHz Out −0.10 0.00 0.10 Lowband(On) 1GHz Out 0.00 0.29 1.00 Sampler 1GHz 0.00 0.81 1.00

Page 55 of 56




Self Check (cont.)Test Group = Sampler Bd Tests

Test Name Minimum Measured Maximum Status +4.5V node 4.30 4.52 4.70 +5.25V node 4.80 5.00 5.20 +8V node 7.90 8.10 8.30 Unlock detector 0.00 0.00 0.00 VCO_BIAS @ 618Mhz 1.20 2.53 4.40 VCO_BIAS @ 905Mhz 3.00 5.75 9.20 VCO_TUNE @ 618Mhz 1.90 2.85 4.00 VCO_TUNE @ 905Mhz 9.20 10.80 11.90

Test Group = Yig Driver Tests

Test Name Minimum Measured Maximum Status +2.5V 2.40 2.53 2.60 +9V 8.82 9.00 9.18 −5.2V −5.30 −5.19 −5.10 −6V −6.12 −5.99 −5.88 AC Coupled Path −0.10 0.00 0.10 Analog Mod Not Present 0.00 0.00 0.00 DC Coupled Path 9.50 10.07 10.50 Ground −0.10 0.00 0.10 Max Scale Pretune 10.78 10.99 11.22 Max Scale Sweep −5.10 −4.99 −4.90 Max scale VGHz 4.00 4.75 7.00 Min Scale Pretune −0.10 0.03 0.10 Min Scale Sweep −0.10 0.00 0.10 Min Scale VGHz −0.10 0.00 0.10

Page 56 of 56

nstewart

Text Box

Find us at www.keysight.com This information is subject to change without notice. © Keysight Technologies, 2019, Published in USA, March 19, 2019, 5992-3799EN

Date post:	25-Jun-2020
Category:	Documents
Upload:	others
View:	38 times
Download:	3 times

ISO/IEC 17025:2017 and ANSI/NCSL Z540.3-2006 …...Certificate of Calibration ISO/IEC 17025:2017 and...

Documents