Jet / Wilton Metalworking , Workholding and Hand Tool - Grainger

metalworking • workholding • hand tools

Contents:WORKHOLDING Vises ................................................... 2-4

Jaw Caps ................................................5

C-Clamps ................................................6

Bar Clamps .............................................7

Specialty Clamps ............................... 8-9

HAND TOOLSSledge Hammers ...................................5

METALWORKINGSawing .............................................. 9-11

Finishing ......................................... 11-12

Drilling ..................................................13

Fully stock your production shop with Quality JEt & wilton products.

WILTON® TRADESMAN VISES-SWIVEL BASESEE PAGE 2

WILTON® 4LB. HEAD UNBREAKABLE HANDLE SLEDGE HAMMERSEE PAGE 5

WILTON® 100 SERIES FORGED C-CLAMPS - HEAVY-DUTYSEE PAGE 6

WILTON® WILTON® 7" x 12" HORIZONTAL BANDSAWSSEE PAGE 9

JET® PARALLEL CLAMPSSEE PAGE 7

2

workholding

Grainger Part Number

Mfr. Model

Jaw Width (in.)

Maximum Opening (in.)

Throat Depth (in.)

Pipe Jaw Capacity (in.)

Ship Weight (lbs.)

WILTON® TRADESMAN VISES-SWIVEL BASE 4LT62 1745 4-1/2 4 3-1/4 1/4 – 2-1/2 42 4LT63 1755 5-1/2 5 3-3/4 1/4 – 3 53 4LT64 1765 6-1/2 6-1/2 4 1/4 – 3-1/2 73 4LT65 1780A 8 7 4-3/4 1/8 – 3-1/2 109

WILTON® MACHINISTS' BENCH VISES- SWIVEL BASE 2Z475 350S 3-1/2 5-1/4 2-3/4 — 41 1Z804 400S 4 6-1/2 3-1/2 — 62 6Z393 450S 4-1/2 7-1/2 4 — 72 6Z394 500S 5 8 4-1/4 — 95 1ATH2 600S 6 10 5-1/2 — 150

WILTON® COMBINATION PIPE AND BENCH VISES-SWIVEL BASE 1ATH3 C-0 3-1/2 5 4-1/2 1/8 – 2-1/2 52 4Z667 C-1 4-1/2 6 4-3/4 1/8 – 3-1/2 78 5Z039 C-2 5 7 5-5/16 1/8 – 4-1/2 113

WILTON® TRADESMAN VISES-SWIVEL BASEProudly made in the USA, the Tradesman round channel vise is designed to handle the most demanding clamping applications. Unlike most vises that have a fixed center nut, the Tradesman round channel vise nut is anchored at the rear. This rear anchored nut provides straight line pull and even pressure resulting in greater durability. The round channel design also allows for a completely enclosed spindle and nut assembly. This enclosure keeps debris out and lubrication in for a lifetime of smooth operation. For ultimate versatility the Tradesman is equipped with main jaws, pipe jaws and a machined anvil work surface. The main jaws are serrated for a sure grip. The pipe jaws are grooved to prevent rotation of round stock and have a two step design to assure a firm hold on both large and small diameter material. Both the main jaws and the pipe jaws are fully replaceable. The Tradesman vise is also equipped with a swivel base with dual locking nuts. The open locking design of the Tradesman base allows for a full 360 degrees of rotation. To prevent rotation during use, both the locking nuts and base have serrated edges that interact positively to assure a non-slip grip when tightened. The main base has four pre-cast holes for mounting the vise to a work surface. Each vise includes a mounting template for quick no guess hole placement for mounting.

• Wider Jaws provide greater clamping surface • Fully enclosed spindle and nut increases the life of the vise• Large anvil work surface• Precision turned sidebar• 360° swivel base with double lockdowns

WILTON® MACHINISTS' BENCH VISES-SWIVEL BASE• Replaceable, hardened steel, machine-serrated top jaw inserts assure a

positive hold• Enclosed design keeps contaminants out and lubrication in for a lifetime of

smooth operation• Horizontal spindle and nut eliminate thread wear and provide increased

clamping power• Large anvil work surface• Swivel base rotates 360 degrees with serrated edge and double lockdowns for

non-slip holding

WILTON® COMBINATION PIPE AND BENCH VISES-SWIVEL BASE• Self-centering hardened steel pipe jaws hold up to 6" pipe safely and securely• Replaceable, hardened steel, machine-serrated top jaw inserts assure a

positive hold• Enclosed design keeps contaminants out and lubrication in for a lifetime of

smooth operation• Horizontal spindle and nut eliminate thread wear and provide increased

clamping power• Large anvil work surface

VISES

No. 4LT62

No. 1ATH3

No. 2Z475

3

Grainger Part Number Mfr. Model

Jaw Width (in.)

Maximum Opening (in.)

Throat Depth (in.)

Pipe Jaw Capacity (in.)

Ship Weight (lbs.)

WILTON® 740 SERIES MECHANICS' VISES - SWIVEL BASE 2Z474 744 4 4-1/2 3-7/16 1/4 – 2 37 2Z346 745 5 5-1/4 3-3/4 1/4 – 2-1/2 50 1ATH4 746 6 5-3/4 4-1/8 1/4 – 3-1/2 64 6YA70 748A 8 8-1/4 4-3/4 1/4 – 3-1/2 89

WILTON® 740 SERIES HIGH-VISIBILITY SAFETY VISES 5LJ84 1550 5 5-1/4 3-3/4 1/4 – 2-1/2 49.4 5LJ85 1560 6 5-3/4 4-1/8 1/4 – 3-1/2 63.65

WILTON® MULTI-PURPOSE MECHANICS' VISE - SWIVEL BASE 5LK13 4500 5-1/2 6 (regular)

9-3/4 (reversed)3-7/16(regular) 2-3/4 (reversed) 1/4 – 3 50

COLUMBIAN MACHINISTS' VISES - SWIVEL BASE 5LK22 604M3 4 6 3-5/8 — 45.18 5LK21 604-1/2M 4-1/2 7 4-1/8 — 58.6 5LK23 605M3 5 8 4-1/4 — 78

COLUMBIAN COMBINATION PIPE AND BENCH VISES - SWIVEL BASE 5LJ87 204-1/2M3 4-1/2 5 5-3/8 1/8 - 3-1/4 60.25 5LJ88 205M3 5-1/2 6 6-1/4 1/8 - 4-1/2 96.3 5LJ89 206M3 6 10 7-1/8 1/8 - 6 163

WILTON® 740 SERIES MECHANICS' VISES - SWIVEL BASEVises have strength and durability to withstand many years of extra heavy-duty service with normal care. Built with replaceable hardened steel serrated metal jaws and pipe jaws, 360° swivel base with serrated locking faces, double lock-downs and extra-deep throats to handle large work pieces.

• Swivel base rotates 360° and has double lockdowns ensuring maximum stability

• Powder coat paint resists scratches and provides a tough durable finish• Replaceable hardened steel top and pipe jaws• Large anvil work surface

WILTON® 740 SERIES HIGH-VISIBILITY SAFETY VISES• Safety color conforms to OSHA standard for physical hazards; Regulation

#1910.144• Replaceable serrated top jaws and pipe jaws• 360° swivel base and double lockdowns• Fully enclosed spindle and nut• Large anvil work surface• Powder coat paint resists scratches and provides a tough durable finish

WILTON® MULTI-PURPOSE MECHANICS' VISE - SWIVEL BASE• Jaw opening expands to an incredible 9-3/4” when reversed• When jaws are in normal position, jaw width measures 5-1/2” wide

with a 6” opening• Replaceable, hardened tool steel jaw faces• Swivel base with four mounting lugs allows for 360° swivel• Two large anvil work surfaces• Two lockdown bolts ensure stability

COLUMBIAN MACHINIST VISES - SWIVEL BASE• Strong, ductile iron main castings are guaranteed against defects in

workmanship and materials• Steel jaw faces made from hardened tool steel have deep knurled

pattern to ensure positive gripping• All sizes (except 6”) feature a generous ground/polished anvil• Swivel base rotates 360° and gear lock bolt ensures positive locking

against slippage

COLUMBIAN COMBINATION PIPE AND BENCH VISES - SWIVEL BASE

• Strong ductile iron main castings are guaranteed for life against defects in workmanship and materials

• Hardened steel jaw faces have deep knurled pattern which ensures strength and longevity

• Pipe jaws are interchangeable and reversible. They do not protrude beyond the jaw faces, so other work can be held without removing pipe jaws

• Swivel base rotates 360° and gear lock bolt ensures positive locking against slippage

No. 2Z474

No. 5LK13

No. 5LK22

No. 5LJ87

No. 5LJ84

4

Grainger Part Number Model

Jaw Width (in.)

Jaw Opening (in.)

Throat Depth (in.)

Pipe Jaw Capacity (in.) Type of Base Type of Nut

Ship Wt (lbs.)

WILTON® 600 SERIES UTILITY VISES - SWIVEL BASE 4TK27 674 4-1/2 4 2-5/8 1/8 – 2 — — 19 4TK28 675 5-1/2 5 3-5/16 1/8 – 2-1/2 — — 29 4TK29 676 6-1/2 5-1/2 3-13/16 1/8 – 2-1/2 — — 43 1ATH1 656HD 6 6 4-3/16 1/8 – 3 — — 63 5C804 648HD 8 7-1/2 4-1/2 1/8 – 3 — — 80

WILTON® SUPER-JUNIOR VISES

5LK42 CBV-65 2-1/2 2-1/8 1-3/4 —Clamp On Swivel 45° left or right

— 11.1

5LK54 SBV-65 2/1/2 2-1/8 1-3/4 — Swivel 45° left or right — 9.4

5LK41 CBV-100 4 2-1/4 2 —Clamp On Swivel 45° left or right

— 18

5LK53 SBV-100 4 2-1/4 2 — Swivel 45° left or right — 14.15

WILTON® VACUUM BASE VISE 5LK01 3VB 2-3/4 2-1/2 — — Vacuum — 13

WILTON® CLAMP-ON BENCH VISE 6YA71 150 3 2-1/2 — — — — 4

WILTON® PIVOT JAW WOODWORKERS' VISE 4LT73 78A 4 x 7 10 — — — Rapid Acting 30

WILTON® 600 SERIES UTILITY VISES - SWIVEL BASEFor utility and light-duty applications. Constructed with formed steel channel beam and casting. Vises feature replaceable, serrated hardened steel top jaws for a light grip, built-in pipe jaws. 180° swivel base, and large anvil

• 180° swivel base with lockdown allows for quick and easy positioning

• Powder coat paint resists scratches and provides a tough durable surface

• Built-in pipe jaws handle various pipe sizes• Large anvil work surface• Perfect for general clamping applications• Rugged and versatile yet moderately priced vises

WILTON® SUPER-JUNIOR® VISES• Super-Junior® Vises come in two styles-clamp-on and

swivel base• Enclosed design keeps contaminants out and lubrication in

for smooth operation• Top jaws are grooved and replaceable• Double lockdowns ensure stability• Both swivel and clamp-on base models can rotate 45° left

or right on base

WILTON® PIVOT JAW WOODWORKERS' VISESFor securely holding wood, plastic, and composite materials. Semi steel casting adds strength at stress points. Jaw pivots and has rapid action enclosed spindle. Jaw can be easily removed if needed.

• Front jaw pivots 10° to allow for clamping irregular shaped parts

• Front jaw moves up 9/16" to act as a full length dog• Pivot jaw can be removed for wider clamping requirements

WILTON® VACUUM BASE VISELightweight and portable, swivels 360°, Vacuum base adheres to any smooth work surface. Jaws are 2-3/4" W; open to 2-1/2". Includes rubber jaw caps.

• Lightweight and portable• Cast aluminum body• 360° swivel base and 180° head tilt• Removable rubber jaw faces. Steel V-grooved jaws• Seal vacuum base to any flat, clean and dry surface by

pressing base to surface and pulling lock arm 180° into position

WILTON® CLAMP-ON BENCH VISE• Portable and compact bench vise for light work in the home,

garage and shop• Cast iron body with cast in pipe jaws• Double steel guide bars• Built-in anvil

Grainger Part Number Description 6YA91 Replacement jaw inserts for 4TK27 Vise 6YA92 Replacement Jaw inserts for 4TK28 Vise 6YA93 Replacement Jaw inserts for 4TK29 Vise 6YA94 Replacement Jaw inserts for 4LT62 Vise 6YA95 Replacement Jaw inserts for 4LT63 Vise 6YA96 Replacement Jaw inserts for 4LT64 Vise 6YA97 Replacement Jaw inserts for 6Z394 Vise 6YA98 Replacement Pipe Jaws for 4LT62, 4LT63, 4LT64 Vises

VISE ACCESSORIES

No. 4TK27

No. 5LK01 No. 6YA71

No. 4LT73

No. 5LK42

workholding

5

Grainger Part Number Description 6YA91 Replacement jaw inserts for 4TK27 Vise 6YA92 Replacement Jaw inserts for 4TK28 Vise 6YA93 Replacement Jaw inserts for 4TK29 Vise 6YA94 Replacement Jaw inserts for 4LT62 Vise 6YA95 Replacement Jaw inserts for 4LT63 Vise 6YA96 Replacement Jaw inserts for 4LT64 Vise 6YA97 Replacement Jaw inserts for 6Z394 Vise 6YA98 Replacement Pipe Jaws for 4LT62, 4LT63, 4LT64 Vises

Grainger Part Number Model Jaw Width (in.) Ship Wt (lbs.) 5C808 A-4 4 1 5LK37 A-4.5 4-1/2 1 5C809 A-5 5 1 5C810 A-6 6 1 5LK38 A-5.5 5-1/2 1 5LK39 A-6.5 6-1/2 1

WILTON® ALUMINUM V-GROOVE MAGNEFIx® JAW CAPS• Aluminum alloy design includes six grooves to compensate for the

unevenness of the workpiece• Deeper V-groove ensures more secure clamping of circular

workpieces• Use together with rubber magnefix jaw caps when clamping taper

pins and spherical parts

Grainger Part Number Model Jaw Width (in.) Ship Wt (lbs.) 5C811 R-4 4 1 5LK50 R-4.5 4-1/2 1 5C812 R-5 5 1 5C813 R-6 6 1 5LK38 A-5.5 5-1/2 1 5LK39 A-6.5 6 1

WILTON® ALUMINUM WITH RUBBER FACE JAW CAPS

• Aluminum alloy with synthetic rubber cover

• Jaw cap conforms to workpiece and grips firmly without slipping while protecting work surface

• Use in combination with aluminum and prism jaw caps to clamp taper pins or tapered workpieces

WILTON® MODEL P-PRISM MAGNEFIx® JAW CAPS

• Jaw construction includes a 120° horizontal V-groove, three vertical V-grooves and a 90° groove for marking out and center punching

• Ideal for light tapping and thread cutting

WILTON® UNBREAKABLE HANDLE SLEDGE HAMMER• Unbreakable handle is made with tempered steel, and surrounded by heavy-

duty molded rubber• Ergonomic handle absorbs shock, ensures comfort and has a slip-resistant grip• High-visibility head adds instant identification under any job site conditions;

encourages safe work habits• Not to be used to strike any object harder than 46HRC• Never replace a sledge handle again! Outlasts wood and fiberglass handle

sledges by thousands of strikes.

Grainger Part Number Model Jaw Width (in.) Ship Wt (lbs.) 5C814 P-4 4 1 5LK47 P-4.5 4-1/2 1 5C815 P-5 5 1 5C816 P-6 6 1 5LK48 P-5.5 5-1/2 1

Grainger Part Number Model Head Weight (lbs.) Handle Length (in.) Ship Weight (lbs.) 5LK44 HVS 412 4 12 6 5LK45 HVS 824 8 24 12 5LK46 HVS 830 8 30 13 5LK43 HVS 1430 14 30 19

6

WILTON® 100 SERIES FORGED C-CLAMPS - HEAVY-DUTY

• Recommended for heavy industrial and construction job site demands, the heavy-duty models are some of the toughest products available for their weight to strength ratio

• 100 Series model frames are forged of superior quality steels

• Spindles are turned from single pieces of square bar stock, and thread modified National Course for superior clamping force and are black-oxide coated

• Perma-Pads® are standard and are also black-oxide coated


Opening Capacity (in.)

Throat Depth (in.)

Spindle Diameter (in.)

Clamp Pressure (lbs.) Ship Wt (lbs.)

WILTON® 100 SERIES FORGED C-CLAMPS - HEAVY-DUTY 5C831 103 0 – 3 2 5/8 8,750 3 5C832 104 0 – 4 2-3/8 3/4 10,000 4-3/4 5C833 106 2 – 6 2-1/2 3/4 11,250 6-5/86YA88 108 4 – 8 2-5/8 3/4 12,500 7-1/2

WILTON® 400 SERIES DROP FORGED C-CLAMPS 5LK03 404-STG 0 – 4-1/4 3-1/4 3/4 6200 4 5LK04 406-STG 0 – 6-1/16 4-1/8 3/4 6600 6 5LK05 408-STG 0 – 8-1/4 5 3/4 6900 7 6YA99 Replacement Spindle Assembly

WILTON® 40 SERIES DROP FORGED C-CLAMPS 5LJ90 1/4 – 2 1-7/8 3/4 12,500 4.25 5LJ91 1/4 – 3-1/4 2-1/2 7/8 16,250 7 5LJ92 1/2 – 4-1/2 2-3/4 7/8 20,000 10.4 6YA87 1-1/2 – 6-1/2 2-3/4 1-1/8 27,500 18.45

WILTON® 400 SERIES DROP FORGED C-CLAMPS• Industry’s top choice for maintenance, production and repair

operations• Drop-forged steel frame, regular-duty with extra

deep-throat• Black-oxide coated spindles and Perma-Pad® resist corrosion, and

are replaceable• Innovative frame geometry for maximum strength• Available with exclusive Wilton-Grip® handle

for increased clamping speed and comfort

WILTON® 40 SERIES DROP FORGED C-CLAMPS• The partial closing, extra heavy duty models are designed to

stand up to the demands of heavy industrial applications like those encountered in ship building

• Hot upset square head on spindle withstands higher torque• Square-head spindle has large diameter rolled thread and

hardened point which provides smoother operation and added strength

• Black oxide coated spindle resists corrosion• Clamping pressure ranging up to 40,000 lbs.

No. 5C831

No. 5LK03

No. 5LJ90

workholding

7

WILTON® REGULAR-DUTY STEEL BAR CLAMPS• The ideal clamps for the metalworker, woodworker and

craftsman• Long, woodscrew handles (4-1/8") for secure hold and easy

gripping• Protective caps included to prevent marring of work• Ratcheting clutch provides quick adjustment at any point• Ductile frame with baked enamel finish

Grainger Part Number

Opening Capacity Max (in.)

Clamp Face (in.)

Spread Capacity (in.)

Throat Depth (in.)

Clamp Pressure (lbs.)

Ship Weight (lbs.)

JET® PARALLEL CLAMPS 6YA76 24 — 31 4-1/8 1000 6-1/2 6YA77 31 — 38 4-1/8 1000 7 6YA78 40 — 47 4-1/8 1000 8 6YA79 50 — 57 4-1/8 1000 9-1/2

JET® HAND SCREW CLAMPS 4CN76 6 — — — — .95 5A322 8 — — — — 1.9 5A323 10 — — — — 3 5A324 12 — — — — 3.9

WILTON® REGULAR-DUTY STEEL BAR CLAMPS 4CN54 6 — — 3-1/2 1000 2.5 4CN55 12 — — 3-1/2 1000 3 4CN56 18 — — 3-1/2 1000 3.5 4CN57 24 — — 3-1/2 1000 4 4CN58 36 — — 3-1/2 1000 5.1

WILTON® HEAVY-DUTY STEEL BAR CLAMPS 4CN60 12 — — 5 1600 5 4CN61 18 — — 5 1600 5.9 4CN62 24 — — 5 1600 6.3 4CN64 30 — — 5 1600 8.2

WILTON® REGULAR DUTY "I" BAR CLAMPS 5A325 24 1 7/8 24 1 13/16 6,000 7.75 5A326 36 1 7/8 36 1 13/16 6,000 8.3 5A327 48 1 7/8 48 1 13/16 6,000 10.25 4CN49 60 1 7/8 60 1 13/16 6,000 11.42 5A328 72 1 7/8 72 1 13/16 6,000 13.8

WILTON® LIGHT-DUTY STEEL BAR CLAMPS 5A329 12 — — 2-1/2 800 1.9 5A330 18 — — 2-1/2 800 2.1 5A331 24 — — 2-1/2 800 2.5 5A332 36 — — 2-1/2 800 3.2

WILTON® HEAVY-DUTY STEEL BAR CLAMPS• Heavy-duty bar clamp design, ideal for the metalworker, woodworker

and craftsman• Ratcheting clutch provides quick adjustment at any point• Long, woodscrew handles (4-3/4") for secure hold and easy gripping• Ductile frame with baked enamel finish

WILTON® REGULAR DUTY "I" BAR CLAMPS• A rapid acting powerful clamp designed and constructed for

hard, everyday production work.• Patented, quick action, no slip clutches are 3/4” apart and

formed in the web for greater bar strength• High strength ductile slide cannot slip or bind, easily released• Steel handle, with comfortable wood crank handle for fast

clamping• Bar dimension is 7/16” x 1-1/2” x 5/32”, screw diameter is 5/8”• Throat depth is 1-13/16” and clamp face is 1-7/8”

WILTON® LIGHT-DUTY STEEL BAR CLAMPS• The ideal clamp for the cabinet maker, woodworker, craftsman

and for light duty metal applications• Ratcheting clutch provides quick adjustment at any point• Long, 3-1/2” woodscrew handles for secure hold and easy

gripping• Protective caps included to prevent marring of work• Ductile frame with baked enamel finish• Zinc plated steel bar with 3/4” swivel pad

JET® PARALLEL CLAMPS• Exclusive design (patent pending) provides precision and power

with exact 90 degree clamping at up to 1,000 lbs. pressure• Precision-Rule™ measurement system (patent pending) provides a

consistent setup and quick identification of opening capacity• Slide-Glide trigger (patent pending) makes precise adjustments

rapidly and easily• Ergonomic SUMOGRIP® handle integrated with soft grip for added

comfort and increased torque• Moveable rail stand/end stop helps preset clamping capacity rapidly

and accurately• Non-marring composite resin jaw faces glue resistant in design,

ensure even clamping pressure• Reversible clamping movable jaw can be reversed to be used as a

spreader• Side profile allows narrow clamping on the side of the jaw face• Acme threaded handle turns easily and applies continuous pressure

JET® HAND SCREW CLAMPS• Solid hardwood bodies provide high clamping pressure• Independent jaw controls allow clamping of irregular shaped

workpieces• Deep-reach provides added capacity and versatility

No. 6YA76 No. 4CN76

No. 4CN54

No. 5A325

No. 5A329

No. 4CN60

JET® PARALLEL FRAMING BLOCK KIT (SET OF 4)• The Cross Doc™ framing blocks can be used for gluing

rectangular frames at four points safely and securely.• Four mounting holes guarantee a permanent setup.

JET® PARALLEL FRAMING BLOCK KIT (SET OF 4) 6YA80 — — — — — 1.7

8

JET® 90° MITER HEAVY-DUTY CLAMP• Clamp is used in gluing, framing, nailing, holding and

screwing projects to create 90° "L" and "T" joints• A maximum opening of 2" on both sides lets you clamp

different thicknesses of materials• Lead screw supplies high-torque clamping

WILTON® 3” CORNER CLAMP CARDED• Clamps or butts joints at true 90º angle for making picture

frames, screens, storm doors and windows• Holds work of different widths up to 3-1/2” (89mm), leaving

joints fully exposed for nailing, gluing, doweling, or for making mitre corrections

• Two countersunk holes permit mounting to work surface• Made of die-cast aluminum alloy

Grainger Part NumberOpening Capacity (in.)

Throat Depth (in.)

Ship Weight (lbs.)

4CN98 3 1-5/8 .4

Grainger Part Number Description Ship Weight (lbs.) 6YA85 90° Miter Heavy Duty Clam 5

JET® JOINTING CLAMP• EXCLUSIVE "Hands-Free Fastening" design aligns and

holds work automatically so you can finish jointing the rest of your project

• Stainless spring steel jaws hold different thicknesses of material up to 3/4" with no limit to the material length

• 90° and "T" joints are no problem• Fiber filled composite material

Grainger Part Number Opening Capacity (in.) Ship Weight (lbs.) 6YA72 3/4 .4


Throat Depth (in.)

Capacity Miter (in.)

Jaw Height (in.)

Jaw Length (in.)

Ship Weight (lbs.)

6YA84 AC-324 4 2-3/4 1-3/8 2-1/4 2-3/4

90° ANGLE CLAMP• Designed with self-centering jaws to

quickly adjust to work pieces• Squarely machined sides and base

provide secure and precise clamping• Oblong holes in base for use in

mounting clamp to workbench

450 STEEL PIPE CLAMP FIxTURES• Clamp is made of high strength iron with steel components• Multiple disc clutch provides instant adjustment, secure hold and

quick release• Designed for use on any length 3/4" threaded pipe

Grainger Part Number Model Pipe Size (in.) Clamp Face (in.) Ship Wt (lbs.) 5A320 450 3/4 1-3/4 3 5A321 452 1/2 1-1/2 2


Capacity Miter (in.) Jaw Height (in.)

Jaw Length (in.)

Ship Weight (lbs.)

5C843 AC-325 3-11/32 1-3/8 4-1/8 8-1/2 4CN99 AC-326 4-3/8 2-3/8 4-1/8 18

WILTON® 90° ANGLE CLAMPS - METALWORKING• The 90º angle clamp is made of high quality cast iron• The copper plated spindle pivots allowing the moveable

jaw to securely grip parts at 90°• Slotted holes are provided in the base for convenient

workbench mounting• Work surfaces (including base) are milled for added

precision

Grainger Part Number ModelUnit Packaging Ship Weight (lbs.)

4CN67 453 4 1/4

453 PIPE CLAMP PADS• Heavy-duty PVC pads that protect and hold finished woodwork and fine metal

work surfaces from damage• Good on 3/4" pipe clamp

workholding

9

Grainger Part Number 3Z990 Round at 90° (in.) 5Round at 45° (in.) 4Rectangle at 90° (in.) 5 x 7-1/2Rectangle at 45° (in.) 4-1/2 x 5Blade Size (in.) 1/2 x .025 x 68-1/2Blade Speeds (SFPM) 85-125-200Blade Wheel Diameter (in.) 7-1/2Bed Height (in.) 23-1/2Motor 1/2HP, 115V, 1Ph, 1725 RPMFloor Space Required (in./L x W x H) 37 x 16 x 37

Net Weight (lbs.) 143

WILTON® 5" x 8" HORIZONTAL METAL CUTTING BANDSAWS

• Adjustable hydraulic feed system• Adjustable ball bearing guides• Heat treated steel worm gear and

bronze drive gear

Grainger Part Number 5Z412 Cutting Capacity:Round at 90° (in.) 7Round at 45° (in.) 6Rectangle at 90° (in.) 7 x 10Rectangle at 45° (in.) 6 x 7Blade Size (in.) 3/4 x .035 x 93Blade Speeds (SFPM) 86-132-178-260Blade Wheel Diameter (in.) 11-7/16Bed Height (in.) 23-1/2Motor 3/4HP, 115V, 1Ph, 1725 RPMFloor Space Required (in./L x W x H) 50 x 18 x 41


WILTON® 7" x 12" HORIZONTAL BANDSAWS

• Blade Guides: Side: Eccentric shaft, ball bearing Rear: Ball bearings

• Blade drive is steel, heat treated worm, driving a bronze worm gear in oil bath

• Heavy-duty cast iron saw head and table

• Oil bath hardened and ground worm gear

• Rapid acting vise

Grainger Part Number 1VLZ5 Cutting Capacity:Round at 90° (in.) 8-1/2Round at 45° (in.) 8-1/2Rectangle at 90° (in.) 8-1/2 x 13Rectangle at 45° (in.) 8-1/2 x 9-3/4Blade Size (in.) 1 x .035 x 114.5Blade Speeds (SFPM) 82, 132, 170, 235Blade Wheel Diameter (in.) 12Bed Height (in.) 27-1/2Motor 1.5HP, 115/230V, 1Ph, Prewired 115VFloor Space Required (in./L x W x H) 62-1/2 x 23 x 48Net Weight (lbs.) 606

WILTON® 8" x 13" HORIZONTAL BANDSAW• Heavy-duty, rigid steel and cast iron construction of

the head, and base provides full blade support and eliminates vibration and deflection

• The combination of an oil bath, gear reduction power train, along with precision blade guides and a hydraulic feed system delivers consistent, accurate cuts and longer blade life

GRAINGER WET KIT FOR 5x8 BANDSAW 3Z990 Grainger Part Number Description 4Z402A Grainger Wet kit for 5X8 Bandsaw 3Z990

10

Grainger Part Number 4KM95 Round @ 90° (in.) 10Rectangle @ 90° (in.) 9 x 16Blade Size (in.) 1 x .035 x 135Blade Wheel Speeds (SFPM) 100 - 350Blade Wheels (in.) 14Height of Work Table (in.) 23-1/2Coolant Tank (gal) 8Motor 1-1/2HP, 115V, 1PhShip Weight (lbs.) 927

WILTON® 10" x 16" HORIZONTAL BANDSAWS• Variable speed drive system allows the operator

to fine tune the blade speed fast and easily• Exclusive 6 contact point blade guide assemblies• Exclusive swivel control panel• One piece wheel cover

Grainger Part Number 4VX64 1VR69 Round @ 90° (in.) 10 10Rectangle @ 90° (in.) 9 X 16 9 X 16Blade Size (in.) 1 X .035 X 135 1 X .035 X 135Blade Wheel Speeds (SFPM) 100 - 350 100 - 350Coolant Tank (gal) 8 8Motor 1-1/2HP, 115/230V, 1PH 2HP, 220V, 3PHShip Weight (lbs.) 1125 1125

WILTON® 10" x 16" MITER BANDSAWS• Variable speed drive system allows the operator to fine-tune the

blade speed fast and easily• Exclusive six contact point blade adjustable guide assemblies • Mitering Head — the workpiece remains

fixed while the head swivels to cut any angle 0°- 45°• Heavy duty transmission utilizes hardened and ground gears

operating in an oil bath

metalworking

11

WILTON® RIP FENCE FOR 14" VERTICAL BANDSAWGrainger Part Number Description 4VX90 Rip Fence for 14" Vertical Bandsaw

Grainger Part Number 1VLZ7 1VLZ9 Height (in.) 12 12Throat (in.) 20 20Blade Length (approx./in.) 150-1/2-156-1/2 150-1/2-156-1/2Blade Width (min.-max./in.) 1/8 - 1 1/8 - 1Blade Speed (SFPM) LOW 65-555, HIGH 390-3280 LOW 65-555, HIGH 390-3280Table Size (in.) 24 X 22-1/2 24 X 22-1/2Table Tilt R-15° L-12° F-B-8° R-15° L-12° F-B-8°Table Height at 90° (in.) 39-1/2 39-1/2Welder (KVA) 4-13/64 4-13/64Motor 2HP, 230V, 3PH 2HP, 460V, 3PHFloor Space Required (in./L x W x H) 42 X 29 X 79 42 X 29 X 79

Net Weight (lbs.) 1210 1210

WILTON® 20" VERTICAL BANDSAWS• Designed for multiple uses cutting both ferrous and

non-ferrous metals• Variable speed drive system• Blade speed and pitch selector• Large cast iron tilting table• LED SFPM readout• Blade welder, cutter and grinder are included

Grainger Part Number 4VX66 Under Guide (in.) 6Under Guide with Riser Block (in.) 12Throat Depth (in.) 13-1/2Blade Size (in.) 3/8 x .025 x 92-1/2Cutting Speeds Wood (SFPM) 3300Cutting Speeds Metal (SFPM) 39, 57, 78, 107, 142, 196, 278Table Tilt to Right 45°Table Tilt to Left 15°Table Height at 90° (in.) 68Table Size (in.) 14 x 14Miter Gauge Groove Wide x Deep (in.) 3/4 x 3/8Motor 1HP,115V,1Ph, 1725 RPMFloor Space Required (in./L x W x H) 20 x 16 x 68Net Weight (lbs.) 280

WILTON® 14" WOOD/METAL VERTICAL BANDSAW

• Cast iron frame• Solid, one-piece steel base for extra stability• Conveniently located on/off switch• Variable speed drive system (8201VS &

8203VS)• Exclusive gear box design allows wood/metal

model saws to be used for a wider variety of metal, wood, non-ferrous metal and plastic cutting applications

WILTON® ABRASIVE DISC CUT-OFF SAW• Portable Abrasive Disc Cut-Off Saw• Combines two operations into one, easy set-up and

operation• Precision cuts on a wide range of materials,

including hard steel, soft steel, ceramics, coated cable and composite materials

• Ideal for small cutting jobs such as cutting tools, screws, pins, bolts, springs, cable and tubing

• 4" abrasive cut-off wheel for cutting• 2" abrasive disc for finishing and deburring• Totally enclosed abrasive cut-off wheel guard• Strong, steel base construction

Grainger Part Number Motor Cut-Off Disc Size Grinding Disc Size Ship Wt (lbs.) 5XT46 1/2 HP, 115V, 1Ph 4 Diameter x .035 Wide 2 Diameter 16.3

WILTON® F225 COLDSAW• Self-centering vise has dual jaws

for burr-free cuts• Sturdy oil bath gear box design• Magnetic starter with overload

protection• Cutting head swivels up to 45° for

miter cuts• Control handle has built-in spring

loaded trigger switch

WILTON® F225 COLDSAW ACCESSORIES

Grainger Part Number 2ELE4Model F225Motor 1HP, 115V, 1PHBlade Speed (RPM) 52Blade Size (mm.) 225Round @ 90° 2-1/2Round @ 45° 2Square @ 90° 2-1/4Floor Space Required (in./L x W x H) 30 x 17 x 32

Blade not included

Grainger Part Number Description 4KM93 Replacement Blade for WiltonF225 225mm x 2mm x 32mm Ferrous 4KM94 Replacement Blade for Wilton F225 225mm x 2mm x 32mm x 120T Ferrous

12

Grainger Part Number 6KG18 Belt Size (in./W x L) 6 x 48Belt Speed (SFPM) 2850Belt Table Size (in.) 7-3/8 x 14-3/4Belt Table Tilt 45° Out, 20° Platen Disc Size (in.) 12Disc Speed (RPM) 1960Disc Table Size (in./W x L) 12 x 16-3/8Disc Table Tilt 45° Out; 20° InMiter Gauge Groove (in.) 3/8 x 3/4Motor 1-1/2HP, 115V, 1PhNet Weight (lbs) 327

Grainger Part Number 5XT47 Belt Size (WxL/in.): 6 x 48Belt Speed (SFPM): 1650Belt Table Size (in.): 6 x 10-1/2Disc Table Size (in.): 7-1/2 x 13Disc Table Tilt (deg.): 45° OutDisc Diameter (in.): 10Disc Speed (RPM): 2100Table Slot(s) (in.): 5/8Motor 1HP, 115V, 1PhNet Weight (lbs) 215

WILTON® INDUSTRIAL COMBINATION BELT & DISC FINISHING MACHINES

• Belt operates at any angle• Powered by a heavy-duty, UL/CSA

approved, 1-1/2HP TEFC motor• Contour, finishing, mitering, flat finishing,

beveling and precision• Fully machined balanced disc runs

vibration-free

WILTON® 6" COMBINATION BELT AND DISC FINISHING MACHINE

• 6" x 48" Belt• 10" Disc• Two cast iron tilting tables for mitering

applications• Full access to the belt when tilted in the

horizontal position• Dust collection shrouds on belt and disc• Quick-release tension mechanism makes belt

changes quick and easy

Grainger Part Number 6KG19 Belt Size (in./W x L) 6 x 48Belt Speed (SFPM) 2850Table Tilt 45° Out, 20° InPlaten (in.) 7-3/8 x 14-3/4Motor 1-1/2HP, 115/230V, 1Ph-Prewired 115VOverall Dimensions (in./W x D x H)

25-1/2 x 19 x 57-1/2 (Width when belt is in horizontal position)


WILTON® 6" INDUSTRIAL BELT FINISHING MACHINE

• Table tilts 45° out, and 20° in for all angle finishing operations

• Adjustable dust deflector and dust chute• Completely enclosed drums and guarded

sanding belt• Fine thread adjustment for simple and easy

belt tracking

Grainger Part Number 5XT48 Disc Size (in.) 12Disc speed (RPM) 1960Table Size (in.) 12 x 16-3/8Table tilt 45° out, 20° inMiter gauge groove (in.) 3/8 x 3/4Motor 1-1/2HP, 115/230V, 1Ph - Prewired 115VOverall Dimensions (in./W x D x H) 16 x 19 x 43Net Weight (lbs.) 234

Grainger Part Number 5XT50 Belt Size (WxL/in.) 6 x 48Belt Speed (SFPM) 28500Belt Table Size (in.) 7-3/8 x 14-3/4Belt Table Tilt (deg.) 45° Out, 20° InTable Slot(s) (in.) 3/8 x 3/4Platen( LxW/in.) 6 1/4 x 14 3/4Minimum Length of Work piece (in.) 350.00%Max. Cut at 45 deg. (in.) 1/4Max Cut at 15 deg. (in.) 3/16Bevel Angle 15° 45°

Number of Inserts for Cutter Head 3" milling cutter head with 8 replaceable carbide inserts

Motor 1-1/2HP, 115/230V, 1Ph, Prewired 115VShip Wt (lbs.) 321

WILTON® 12" INDUSTRIAL DISC FINISHING MACHINE

• Optimum speed of 1960 rpm, which is ideal for both metal and wood finishing

• Fully machined, balanced disc runs vibration-free

• Plain and compound miters are easily obtained by using the standard die-cast aluminum miter gauge

WILTON® BELT AND EDGE MILL• Combination 6" Belt And Chamfering Machine• 6" BELT SANDER• Contour finishing, mitering, flat finishing just to name

a few applications• Will handle virtually all the finishing operations in a

production line• Adjustable heavy-duty, cast iron, removeable platen• Removable upper guard for contour finishing• Variable-position locks; belt head adjusts vertically,

horizontally and in-between

metalworking

Grainger Part Number 3Z813 Belt Size (in./W x L) 2 x 72Belt Speed (SFPM) 4600Contact Wheel (in.) 8Contact Wheel Durometer 70Motor 1HP, 115/230V, 1PhNet Weight (lbs.) 113

Shown with optional stand

WILTON® 2" x 72" SqUARE WHEEL GRINDER

• Infinitely Variable Speeds 1100 to 6000 sfpm (4126AC)

• Latest AC Inverter Variable Speed technology (4126AC)

• Continuous speed adjustment while in operation

• East to view sfpm readout

13

Grainger Part Number 5XT43 5XT44 5XT45 Type 15" Bench 15" Floor 20" FloorDrills to Center of Circle (in.) 15 15 20Cast Iron Drilling Capacity (max./in.) 5/8 5/8 3/4Steel Drilling Capacity (max./in.) 1/2 1/2 5/8Quill Diameter (in.) 1-7/8 1-7/8 2-1/4Quill Travel (in.) 3-3/8 3-3/8 4-3/4Spindle Taper 2 MT 2 MT 3 MT

Separate Number & Range of Spindle Speeds (RPM)

12 (250, 340, 390, 510, 600, 650, 990, 1550, 1620, 1900, 2620, 3100)

12 (250, 340, 390, 510, 600, 650, 990, 1550, 1620, 1900, 2620, 3100)

12 (150, 260, 300, 440, 490, 540, 1150,1550,1840, 2220, 2950, 4200)

Overall Table Size (in.) 10 x 10 10 x 10 18-1/2 x 16-1/2Column Diameter (in.) 2-7/8 2-7/8 3-5/8Base Size (in.) 11 x 18-1/2 11 x 19-1/2 22-3/4 x 17-3/4Spindle to Base (in.) 24-1/2 48-3/4 43-1/2

Motor 3/4HP, 115V, 1Ph, 1725 RPM

3/4HP, 115V, 1Ph, 1725 RPM

1-1/2HP, 115V, 1Ph, 1725 RPM

Floor Space Required (in./L x W x H) 26 x 13-3/8 x 39 26 x 13-3/8 x 63-1/2 34 x 21 x 67

Net Weight (lbs.) 147 167 321

WILTON® 15” & 20” STEP PULLEY DRILL PRESSES

• Cast iron head• Large quill allows greater accuracy• Head casting features a permanently

lubricated ball bearing spindle assembly, using four heavy-duty ball bearings mounted in an enclosed quill for extended life

• Massive T-slotted production work table (Model 2550 only)

• Large ground steel column diameter for maximum head and table support

DRILL CHUCKGrainger Part Number Description 6X249 Drill Chuck, 3/16" - 3/4" Capacity, Arbor #3

WILTON® 20" VARIABLE SPEED DRILL PRESSES

• Variable spindle speeds from 300 to 2000 RPM• External #3 Morse Taper• Front mounted positive control depth stop• Massive 3" quill diameter• Heavy-duty cast iron design• Table rotates 360° around column

Grainger Part Number 5XT41 5XT42 Drills to Center of Circle (in.) 20 20Cast Iron Drilling Capacity (in.) 1-1/4 1-1/4Steel Drilling Capacity (in.) 1 1Column Diameter (in.) 4-1/2 4-1/2Range of Spindle Speeds (RPM) 300 to 2000 300 to 2000Spindle Travel (in.) 6 6Spindle Taper 3 MT 3 MTQuill Diameter (in.) 3 3Table Size (in.) 18-1/8 x 14-3/4 18-1/8 x 14-3/4T-Slots Number & Size (in.) 2 & 5/8 2 & 5/8Table Travel (in.) 32-3/8 32-3/8Base Working Surface (in.) 15-1/4 x 12-1/16 15-1/4 x 12-1/16Base Slots Number & Size (in.) 2 & 5/8 2 & 5/8

Motor 2HP, 115/220V, 1Ph, Prewired 115V

2HP, 220/440V, 3Ph, Prewired 440V

Floor Space Required (in./L x W x H) 34-1/4 x 27 x 77-1/4 34-1/4 x 27 x 77-1/4Net Weight (lbs.) 750 750

Grainger Part Number 4LL11 5XT73 Type 15" Floor 15" FloorRange of Spindle Speeds (RPM): 400 to 5000 400 to 5000Spindle Taper: 2 MT 2 MTQuill Diameter (in.): 2 1/4 2 1/4T-Slots Number and Size (in.): 2 & 1/2 2 & 1/2Work Table Weight Capacity (lbs.): 12-1/2 x 14-1/2 12-1/2 x 14-1/2Column Diameter (in.): 3 3Drilling Capacity Cast Iron (in.): 5/8 5/8Drilling Capacity Mild Steel (in.): 1/2 1/2Quill Travel (in.): 6 6Table Size (in.): 15-1/4 x 17-3/4 15-1/4 x 17-3/4Spindle Distance to Base (in.): 47-1/2 47-1/2Net Weight: 387.2 426

Motor: 1 HP, 115/230V, 1Ph, Prewired 115V

1HP, 220/440V, 3Ph, Prewired 220V

WILTON® 15" VARIABLE SPEED DRILL PRESSES

• Speeds from 400 to 5,000 RPM• Handwheel adjustment sets the speeds• Large 2-1/4” quill allows greater

accuracy• 3" column diameter for maximum head

support• Accurate depth stop for precise hole

depths

14

1ATH1 656HD, Utility Vise, 6" Jaw Width, 6" Jaw Opening, 4-3/16" Throat Depth 191 4

1ATH2 600S, Machinists' Bench Vises - Swivel Base, 6" Jaw Width, 10" Jaw Opening, 5-1/2" Throat Depth 10031 2

1ATH3 C-0, Combination Pipe and Bench Vises - Swivel Base, 3-1/2" Jaw Width, 5" Jaw Opening, 4-1/2" Throat Depth 10200 2

1ATH4 746, 740 Series Mechanics' Vise - Swivel Base, 6" Jaw Width, 5-3/4" Jaw Opening, 4-1/8" Throat Depth 21500 3

1VLZ5 Wilton 8" x 13" Horizontal Bandsaw 1-1/2HP 115/230V 1Ph 7015 9

1VLZ7 Wilton 20" Vertical Bandsaw 2HP 220V 3Ph 8020FW-2 11

1VLZ9 Wilton 20" Vertical Bandsaw 2HP 440V 3Ph 8020FW-4 11

1VR69 Wilton 10" Horizontal Mitering Bandsaw 2HP 230V 3 Ph 7040M 10

1Z804 400S, Machinists' Bench Vises - Swivel Base, 4" Jaw Width, 6-1/2" Jaw Opening, 3-1/2" Throat Depth 10016 2

2ELE4 225mm Manual Coldsaw 1HP 115V 1Ph F225 11

2Z346 745, 740 Series Mechanics' Vise - Swivel Base, 5" Jaw Width, 5-1/4" Jaw Opening, 3-3/4" Throat Depth 21400 3

2Z474 744, 740 Series Mechanics' Vise - Swivel Base, 4" Jaw Width, 4-1/2" Jaw Opening, 3-7/8" Throat Depth 21300 3

2Z475 350S, Machinists' Bench Vises - Swivel Base, 3-1/2" Jaw Width, 5-1/4" Jaw Opening, 2-3/4" Throat Depth 10011 2

3Z813 Square Wheel Belt Grinder 4103 12

3Z990 Wilton 5" x 8" Horizontal Bandsaw Dry 1/2HP 115V 1Ph 3130 9

4CN49 5' Jaw Opening, "I" Bar Clamp - 6,000 Load Capacity, Regular-Duty 21805 7

4CN54 6" Jaw Opening, Bar Clamp - Regular-Duty, 3-1/2" Throat Depth 53306 7





4CN60 12" Jaw Opening, Bar Clamp - Heavy-Duty, 5" Throat Depth 53512 7




4CN67 453, 4-Piece Clamp Fixture Pad Set 63112 8

4CN76 6" Hand Screw 709864 7

4CN98 3' Corner Clamp Carded 48404 8

4CN99 AC-326, 90 Degree Angle Clamp - Metalworking, 4-3/8" Miter Capacity, 2-3/8" Jaw Height, 4-1/8" Jaw Length 64002 8

4KM93 Replacement Blade for WiltonF225 225mm x 2mm x 32mm Ferrous 579000 11

4KM94 Replacement Blade for Wilton F225 225mm x 2mm x 32mm x 120T Ferrous 579002 11

4KM95 Wilton 10" x 16" Horizontal Bandsaw 1-1/2HP 115/230V 1 Ph 7020 10

4LL11 15" Variable Speed Drill Press , #2 MT Spindle, Chuck and Arbor, 115/220V, 1PH, 1HP Motor with Rotary Drum Switch A5816 13

4LT62 1745, Tradesman Vise , 4-1/2" Jaw Width, 4" Jaw Opening, 3-1/4" Throat Depth 63199 2

4LT63 1755, Tradesman Vise, 5-1/2" Jaw Width, 5" Jaw Opening, 3-3/4" Throat Depth 63200 2

4LT64 1765, Tradesman Vise, 6-1/2"Jaw Width, 6-1/2" Jaw Opening, 4" Throat Depth 63201 2

4LT65 1780A, Tradesman Vise , 8" Jaw Width, 7" Jaw Opening, 4-3/4" Throat Depth 63202 2

4LT73 78A, Pivot Jaw Woodworkers' Vise - Rapid Acting, 4" x 7" Jaw 63144 4

Grainger Part No. Product Description

Supplier Stock No.

Page No.


Supplier Stock No.

Page No.

CROSS REFERENCE

4TK27 674, Utility Vise , 4-1/2" Jaw Width, 4" Jaw Opening, 2-5/8" Throat Depth 11126 4

4TK28 675, Utility Vise , 5-1/2" Jaw Width, 5" Jaw Opening, 3-3/16" Throat Depth 11127 4

4TK29 676, Utility Vise , 6-1/2" Jaw Width, 5-1/2" Jaw Opening, 3-13/16" Throat Depth 11128 4

4VX64 Wilton 10" Horizontal Mitering Bandsaw 1-1/2HP 115/230V 1Ph 115V at Switch 7020M 10

4VX66 Wilton 14" Wood/Metal Vertical Bandsaw 1HP 115V 1Ph 8201K 11

4VX90 Rip Fence for 14" Vertical Bandsaw 5782171 11

4Z402 Grainger Wet Kit 4Z402A for 5X8 Bandsaw 3130 5631400 10

4Z667 C-1, Combination Pipe and Bench Vises - Swivel Base, 4-1/2" Jaw Width, 6" Jaw Opening, 4-3/4" Throat Depth 10225 2

5A320 Steel Pipe Clamp Fixture, 3/4" 63110 8

5A321 Steel Pipe Clamp Fixture, 1/2" 63111 8

5A322 8" Hand Screw 709865 7

5A323 10" Hand Screw 709866 7

5A324 12" Hand Screw 709867 7

5A325 2' Jaw Opening, "I" Bar Clamp - 6,000 Load Capacity, Regular-Duty 21801 7




5A329 12" Jaw Opening, Steel Bar Clamp - Light-Duty, 2-1/2" Throat Depth 42912 7




5C804 648HD, Workshop Vise, 8" Jaw Width, 7-1/2" Jaw Opening, 4-1/2" Throat Depth 11800 4

5C808 A-4, Aluminum Jaw Cap, 4" Jaw Width 14828 5



5C811 R-4, Rubber Face Jaw Cap, 4" Jaw Width 14840 5



5C814 P-4, Prism Jaw Cap, 4" Jaw Width 14846 5



5C831 103, 100 Series Forged C-Clamp - Heavy-Duty, 0" - 3" Jaw Opening , 2" Throat Depth 14128 6

5C832 104, 100 Series Forged C-Clamp - Heavy-Duty, 0" - 4" Jaw Opening , 2-1/4" Throat Depth 14142 6

5C833 106, 100 Series Forged C-Clamp - Heavy-Duty, 2" - 6" Jaw Opening, 2-1/2" Throat Depth 14156 6

5C843 AC-325, 90 Degree Angle Clamp - Metalworking, 3-11/32" Miter Capacity, 1-3/8" Jaw Height, 4-1/8" Jaw Length 64000 8

5LJ84 1550, High-Visibility Safety Vise, 5" Jaw Width, 5-1/4" Jaw Opening 63187 3

5LJ85 1560, High-Visibility Safety Vise, 6" Jaw Width, 5-3/4" Jaw Opening 63188 3

5LJ87 204-1/2M3, Combination Pipe and Bench Vises - Swivel Base,4-1/2" Jaw Width, 5" Jaw Opening, 5-3/8" Throat Depth 10404 3

5LJ88 205M3, Combination Pipe and Bench Vises - Swivel Base,, 5-1/2" Jaw Width, 6" Jaw Opening, 6-1/4" Throat Depth 10405 3

15


Supplier Stock No.

Page No.


Supplier Stock No.

Page No.

5LJ89 206M3, Combination Pipe and Bench Vises - Swivel Base,, 6" Jaw Width, 10" Jaw Opening, 7-1/8" Throat Depth 10406 3

5LJ90 1/4" - 2" Jaw Opening, 40 Series Forged C-Clamp - Partially Closing Spindle, Heavy-Duty, 1-7/8" Throat Depth 27204 6

5LJ91 1/4" - 3-1/4" Jaw Opening, 40 Series Forged C-Clamp - Partially Closing Spindle, Heavy-Duty, 2-1/2" Throat Depth 27205 6

5LJ92 1/2" - 4-1/2" Jaw Opening, 40 Series Forged C-Clamp - Partially Closing Spindle, Heavy-Duty, 2-3/4" Throat Depth 27206 6

5LK01 3VB, Vacuum Base Vise, 2-1/4" Jaw Width, 2-1/2" Jaw Opening 63500 4

5LK03 404-STG, 400 Series C-Clamp, 0" - 4-1/4" Jaw Opening, 3-1/4" Throat Depth 63153 6

5LK04 406-STG, 400 Series C-Clamp, 0" - 6-1/16" Jaw Opening, 4-1/8" Throat Depth 63154 6

5LK05 408-STG, 400 Series C-Clamp, 0" - 8-1/4" Jaw Opening, 5" Throat Depth 63155 6

5LK13 4500, Multi-Purpose Mechanics' Vise - Swivel Base, 5-1/2" Jaw Width, 6" (9-3/4" Reversed) Jaw Opening, 3-3/4" Throat Depth

14500 3

5LK21 604-1/2M3, Machinists' Vises - Swivel Base, 4-1/2" Jaw Width, 7" Jaw Opening, 4-1/8" Throat Depth 10204 3

5LK22 604M3, Machinists' Vises - Swivel Base, 4" Jaw Width, 6" Jaw Opening, 3-5/8" Throat Depth 10203 3

5LK23 605M3, Machinists' Vises - Swivel Base, 5" Jaw Width, 8" Jaw Opening, 4-1/4" Throat Depth 10205 3

5LK37 A-4.5, Aluminum Jaw Cap, 4-1/2" Jaw Width 14829 5



5LK41 CBV-100, Super-Junior Vise, 4" Jaw Width, 2-1/4" Jaw Opening 63247 4

5LK42 CBV-65, Super-Junior Vise, 2-1/2" Jaw Width, 2-1/8" Jaw Opening, 2" Throat Depth 63198 4

5LK43 HVS 1430, 14 Lb. Head, Unbreakable Handle Sledge Hammer, 30" Handle 20003 5




5LK47 P-4.5, Prism Jaw Cap, 4-1/2" Jaw Width 14847 5



5LK50 R-4.5, Rubber Face Jaw Cap, 4-1/2" Jaw Width 14841 5



5LK53 SBV-100, Super-Junior Vise, Swivel Base, 4" Jaw Width, 2-1/4" Jaw Opening 63248 4

5LK54 SBV-65, Super-Junior Vise, Swivel Base, 2-1/2" Jaw Width, 2-1/8" Jaw Opening 63244 4

5XT41 20" Variable Speed Drill Press 2HP, 1PH, 115/220V 2221VS 13

5XT42 20" Variable Speed Drill Press 3 HP, 3PH, 220/440V 2223VS 13

5XT43 15" Floor Model Drill Press, 3/4HP, 1725 RPM, 115V Motor (KD) 2500 13

5XT44 15" Bench Model Drill Press, 1/2HP, 1725 RPM, 115V Motor (KD) 2530 13

5XT45 20" Floor Model Drill Press, 1HP, 1725 RPM, 115V Motor (KD) 2550 13

5XT46 Fast Cut Disk Cut Off saw with disc grinder 3034 11

5XT47 6" Belt & Disc Sander w/Special Packaging 4210B 12

5XT48 12" Disc Sander 1-1/2HP TEFC Motor, 1Ph, 115/230V, Push Button Switch 4400A 12

5XT50 Belt and Edge Mill 1-1/2HP TEFC Motor, 1Ph, 115/230V and Push Button Switch 4500 12

5XT73 15" Variable Speed Drill Press, Floor, #2 MT Spindle, Chuck and Arbor, 220/440V, 3PH, 3HP Motor with Rotary Drum Switch

A5818 13

5Z039 C-2, Combination Pipe and Bench Vises - Swivel Base, 5" Jaw Width, 7" Jaw Opening, 5-5/16" Throat Depth 10250 2

5Z412 Wilton 7" X 12" Horizontal Bandsaw 3/4HP 115V 1Ph 3410 9

6HH06 3/4" Nominal Opening, Saw Buddy 49000 8

6KG18 Industrial Combination Belt and Disc Finishing Machine 4200A 12

6KG19 6" Industrial Belt Finishing Machine 4300A 12

6X249 Jacob's Chuck, 3/16" - 3/4" Capacity, Arbor #3 5108010 13

6YA70 748A, 740 Series Mechanics' Vise - Swivel Base, 8" Jaw Width, 8-1/4" Jaw Opening, 4-3/4" Throat Depth 21800 3

6YA71 150, Bench Vise - Clamp-On Base, 3" Jaw Width, 2-1/2" Maximum Jaw Opening 33150 4

6YA72 Jointing Clamp (Pair) 709055 8

6YA76 24" Parallel Clamp 70424 7




6YA80 Parallel Framing Block Kit (Set of 4) 70401 7

6YA84 AC-324, 90 Degree Angle Clamp, 4" Throat, 2-3/4" Miter Capacity, 1-3/8" Jaw Height, 2-1/4" Jaw Length 44324 8

6YA85 90 Degree Miter Heavy Duty Clamp 709857 8

6YA87 1-1/2" - 6-1/2" Jaw Opening, 40 Series Forged C-Clamp - Partially Closing Spindle, Heavy-Duty, 3-3/8" Throat Depth 27208 6

6YA88 108, 100 Series Forged C-Clamp - Heavy-Duty, 4" - 8" Jaw Opening, 2-3/4" Throat Depth 14170 6

6YA91 Replacement jaw inserts for 4TK27 Vise 76654S41 4

6YA92 Replacement Jaw inserts for 4TK28 Vise 11127S41 4

6YA93 Replacement Jaw inserts for 4TK29 Vise 11128S41 4

6YA94 Replacement Jaw inserts for 4LT62 Vise 2908060 4



6YA97 Replacement Jaw inserts for 6Z394 Vise 2905020 4

6YA98 Replacement Pipe Jaws for 4LT62, 4LT63, 4LT64 Vises 2904200 4

6YA99 Spindle Assembly for 5LK04 1700190 6

6Z393 450S, Machinists' Bench Vises - Swivel Base, 4-1/2" Jaw Width, 7-1/2" Jaw Opening, 4" Throat Depth 10021 2

6Z394 500S, Machinists' Bench Vises - Swivel Base, 5" Jaw Width, 8" Jaw Opening, 4-1/4" Throat Depth 10026 2

Stock No. 8SS2874 5M 3/09

©2009 WMH Tool Group, Inc.All Rights Reserved. Printed in the U.S.A.

The color WHITE is a registered trademark of WMH Tool Group, Inc.

Date post:	12-Sep-2021
Category:	Documents
Upload:	others
View:	2 times
Download:	0 times

Jet / Wilton Metalworking , Workholding and Hand Tool - Grainger

Documents