2-WAY FULL-RANGE LOUDSPEAKER 110° × 15°See NOTES TABULAR DATA for detailsCONFIGURATIONSubsystem: Transducer Loading
LF 2× 10 in cone Vented
HF 3× .75 in exit, 1.75 in voice coil Horn-loaded compression driver
Operating Mode:
Amplifier Channels External Signal Processing
Single-amp LF/HF High pass filter
Bi-amp LF,HF DSP w/2-way filtersPERFORMANCE Operating Range: 65 Hz to 20 kHz
Nominal Beamwidth: (rotatable) Horz 110° Vert 15°
Axial Sensitivity (whole space SPL): LF/HF 95 dB 65 Hz to 20 kHz
LF 96 dB 65 Hz to 1520 Hz
HF 102 dB 1320 Hz to 20 kHz
Input Impedance (ohms): Nominal Minimum
LF/HF 8 6.4 @ 200 Hz
LF 8 6.5 @ 630 Hz
HF 8 11.9 @ 20 kHz
High Pass Filter: High Pass =>60 Hz, 12 dB/octave Butterworth
Accelerated Life Test:
LF/HF 79.9 V 800 W @ 8 ohm
LF 79.9 V 800 W @ 8 ohm
HF 35.7 V 160 W @ 8 ohm
Calculated Axial Output Limit (whole space SPL): Average Peak
LF/HF 124 dB 130 dB
LF 125 dB 131 dB
HF 124 dB 130 dB
ORDERING DATA Description Part Number
EAW JFL213 Black 2039885-90
Optional Accessories
Eye Bolt Forged Shoulder M10 X 1.5 X 37mm 0029818
Flybar JFL & HDA Black [FB221] 2036411
FEATURES• Two-way, constant curvature line array module
• Compact and light; a “one-person lift”
• Easy to mount, fly or ground stack
• Two-module, pole-mounted arrays or up to five modules flown
• Classic EAW output, pattern control and fidelity
DESCRIPTIONThe JFL213 compact, two-way line array module features a range of EAW’s most innovative line array technologies within a mobile, light-weight package appropriate in a wide range of small- to medium-sized venues. With its companion subwoofer, the JFL118, this easy-to-use system solves problems in both portable and permanently installed applications.
The JFL213’s two-way design mounts dual 10-in cone transducers in an optimally vented enclosure and spaced to extend pattern control into the low frequency range. Three horn-loaded, 0.75-in exit / 1.75-in voice coil compression drivers deliver even dispersion of high frequency information over the entire 110° horizontal coverage area.
EAW engineers optimized the JFL213’s size, shape and weight for easy transport and setup by a single person, with side handles designed as part of the rigging system and aligned with the enclosure’s center of balance. Users can mount up to two JFL213s on a loudspeaker stand with a 35mm/1.38-in diameter pole. The cleverly-designed, dual-angle pole mount cup allows the bottom enclosure to be aimed 0° or -15°. (A two-module array with the lower modules aimed at -15° aims the upper module at 0°.) The JFL118 features an integrated pole mount cup, letting it serve as a large, stable base for pole mounting.
The JFL213’s ultra-strong rigging system allows users to hang up to five modules with a 10:1 safety factor, which meets or exceeds all standards enforced throughout the world. A single person can easily connect the modules to the accessory FB221 Fly Bar as well as to each other. The FB221 also doubles as a ground stack base for up to four JFL213s. For permanent installation, each JFL213 provides a pair of M10 threaded mounting points.
The JFL213 allows users to switch between single- or bi-amp powering modes. The JFL213 delivers optimal performance when operated in bi-amp mode with an EAW UX Series digital processor. In addition to the HF shading filters, UX Series digital processor deliver EAW Focusing™ setting, which correct for anomalies that occur in the time domain of any loudspeaker or transducer.
Enclosures are protected by our tough, scratch-resistant RoadCoat™ finish and durable, foam-backed steel grilles protect the transducers. Six year warranty.
JFL213 Specifications
Eastern Acoustic Works • One Main Street • Whitinsville, MA 01588 • tel 800 992 5013 / 508 234 6158 • fax 508 234 8251 • www.eaw.comAugust 2012Part Number: RD0732 Rev 100EAW products are continually improved. All specifications are therefore subject to change without notice.
NOTE: This drawing has been reduced. Do not scale.
JFL213 Specifications
Eastern Acoustic Works • One Main Street • Whitinsville, MA 01588 • tel 800 992 5013 / 508 234 6158 • fax 508 234 8251 • www.eaw.comAugust 2012Part Number: RD0732 Rev 100EAW products are continually improved. All specifications are therefore subject to change without notice.
12
34
12
34
ABC
ABC
PR
O E
NG
INE
ER
2039
856-
CD
-A_D
WG
_CU
STO
MR
_JFL
213
THE
INFO
RM
ATI
ON
CO
NTA
INE
DH
ER
EIN
IS P
RO
PR
IETA
RY
AN
DC
ON
FID
EN
TIA
L P
RO
PE
RTY
OF
LOU
D T
EC
HN
OLO
GIE
S, I
NC
.A
LL R
IGH
TS R
ES
ER
VE
D
UN
LES
S O
THE
RW
ISE
SP
EC
IFIE
D:
ALL
DIM
EN
SIO
NS
AR
E IN
INC
HE
S D
UA
L [M
M] D
IME
NS
ION
S
FOR
RE
F O
NLY
TO
LER
AN
CE
IN IN
CH
ES
LIN
EA
R ±
0.1
3 in
/ ±
3.3
mm
AN
GLE
S ±
1°
(X
.XX
) = R
EF
DIM
SN
O T
OLE
RA
NC
E IM
PLI
ED
TS
C =
TH
EO
RE
TIC
AL
SH
AR
P C
OR
NE
R
DIM
EN
SIO
NS
AC
RO
SS
CE
NTE
RLI
NE
STO
BE
SY
MM
ETR
ICA
LR
EV
ISIO
N:
DR
AW
ING
NU
MB
ER
:
THIR
D A
NG
LE P
RO
JEC
TIO
N
TITL
E:
SC
ALE
:1
1
ww
w.e
aw.c
om
15°
11.8
7[3
01.5
]TS
C15
.64
[397
.2]
(24.
84[6
31.0
])
11.3
7[2
88.8
]TS
C
12.3
7[3
14.2
]
9.73
[247
.3]
8.95
[227
.3]
11.7
4[2
98.1
]
21.1
4[53
7.0]
6.22
[158
.0]
19.4
1[49
3.0]
10.4
3[2
65.0
]
6.89
[175
.0]
5.0
[128
]
6.39
[162
.2]
6.22
[158
.0]
0.18
[4.5
]
DA
TEC
HA
NG
E N
UM
BE
RR
EV
2039
856-
CD
A
AS
HE
ET
O
F 0.
088
DW
G C
US
TOM
ER
JFL
213
[ME
CH
AN
ICA
L S
PE
CIF
ICA
TIO
N]
DA
TEC
HA
NG
E N
UM
BE
RR
EV
9/17
/12
EC
OW
HT8
923
A
2039
856-
CD
A
AS
HE
ET
O
F 0.
088
DW
G C
US
TOM
ER
JFL
213
[ME
CH
AN
ICA
L S
PE
CIF
ICA
TIO
N]
VIE
W A
-A
FRO
NT
TOP
RIG
HT
SID
ED
IME
NS
ION
S A
PP
LYTO
BO
TH S
IDE
S
JFL2
132X
HA
ND
LES
,P
RO
PR
IETA
RY
RIG
GIN
G S
YS
TEM
BA
CK
NO
TES
:1.
SY
MB
OL
I
ND
ICA
TES
MO
UN
TIN
G P
OIN
T,
M10
X 1
.5 T
HR
EA
DE
D H
OLE
(PI A
NG
LE).
2. S
YM
BO
L
IN
DIC
ATE
S C
EN
TER
OF
BA
LAN
CE
.3.
WE
IGH
T A
PP
RO
X. 6
2 lb
[28
kg].
4. S
HIP
PIN
G W
EIG
HT
AP
PR
OX
. 75
lb [3
4 kg
].
GR
ILLE
PA
RTI
ALL
YS
HO
WN
INP
UT
PA
NE
L
2X S
TAC
K P
AD
RO
UTS
PO
LE
MO
UN
T C
UP
S
AA
Exterior-grade Baltic birch plywoodWear resistant textured black paintPowder-coated perforated steel
MaterialFinishGrille
ENCLOSURE
BeamwidthHorizontal = orange Vertical = black
PERFORMANCE DATASee NOTES GRAPHIC DATA for details
Frequency Response: ProcessedLF = green, HF = black, Complete = blue
Frequency Response: UnprocessedLF = green, HF = black, Complete = blue
SP
L (d
B)
SP
L (d
B)
Frequency (Hz)
Frequency (Hz)
ImpedanceLF = green, HF = black, Complete = blue
Phase LinearityComplete = blue
Ohm
sD
egre
es
Frequency (Hz)
Frequency (Hz)
Deg
rees
Frequency (Hz)
Frequency Response: Unprocessed Single-ampSingle Box = green, Multi Box = orange, Long Throw = black
SP
L (d
B)
Frequency (Hz)
JFL213 Specifications
Eastern Acoustic Works • One Main Street • Whitinsville, MA 01588 • tel 800 992 5013 / 508 234 6158 • fax 508 234 8251 • www.eaw.comAugust 2012Part Number: RD0732 Rev 100EAW products are continually improved. All specifications are therefore subject to change without notice.
100
10
110 100 1000 20000
360
100
10
1100 1000 20000
10 100 1000 20000
100
60
70
80
90
120
110
10 100 1000 20000
-10
-50
-40
-30
-20
10
0
180
-0
-180
-90
90
10 100 1000 20000
10 100 1000 20000
100
60
70
80
90
120
110
HORIZONTAL POLAR DATASee NOTES GRAPHIC DATA for details
JFL213 Specifications
Eastern Acoustic Works • One Main Street • Whitinsville, MA 01588 • tel 800 992 5013 / 508 234 6158 • fax 508 234 8251 • www.eaw.comAugust 2012Part Number: RD0732 Rev 100EAW products are continually improved. All specifications are therefore subject to change without notice.
90˚
-90˚
45˚
-45˚
0˚
135˚
-135˚
180˚
90˚
-90˚
45˚
-45˚
0˚
135˚
-135˚
180˚
90˚
-90˚
45˚
-45˚
0˚
135˚
-135˚
180˚
90˚
-90˚
45˚
-45˚
0˚
135˚
-135˚
180˚
90˚
-90˚
45˚
-45˚
0˚
135˚
-135˚
180˚
90˚
-90˚
45˚
-45˚
0˚
135˚
-135˚
180˚
100Hz125Hz160Hz200Hz
250Hz315Hz400Hz500Hz
630Hz800Hz1000Hz1250Hz
1600Hz2000Hz2500Hz3150Hz
4000Hz5000Hz6300Hz8000Hz
10000Hz12500Hz16000Hz
VERTICAL POLAR DATASee NOTES GRAPHIC DATA for details
JFL213 Specifications
Eastern Acoustic Works • One Main Street • Whitinsville, MA 01588 • tel 800 992 5013 / 508 234 6158 • fax 508 234 8251 • www.eaw.comAugust 2012Part Number: RD0732 Rev 100EAW products are continually improved. All specifications are therefore subject to change without notice.
90˚
-90˚
45˚
-45˚
0˚
135˚
-135˚
180˚
90˚
-90˚
45˚
-45˚
0˚
135˚
-135˚
180˚
90˚
-90˚
45˚
-45˚
0˚
135˚
-135˚
180˚
90˚
-90˚
45˚
-45˚
0˚
135˚
-135˚
180˚
90˚
-90˚
45˚
-45˚
0˚
135˚
-135˚
180˚
90˚
-90˚
45˚
-45˚
0˚
135˚
-135˚
180˚
100Hz125Hz160Hz200Hz
250Hz315Hz400Hz500Hz
630Hz800Hz1000Hz1250Hz
1600Hz2000Hz2500Hz3150Hz
4000Hz5000Hz6300Hz8000Hz
10000Hz12500Hz16000Hz
NOTESTABULAR DATA 1. Measurement/Data Processing Systems: Primary - FChart: proprietary EAW software; Secondary - Brüel & Kjær 2012. 2. Microphone Systems: Earthworks M30; Brüel & Kjær 4133 3. Measurements: Dual channel FFT; length: 32 768 samples; sample rate: 48 kHz; logarithmic sine wave sweep. 4. Measurement System Qualification (includes all uncertainties): SPL: accuracy +/-0.2 dB @ 1 kHz, precision +/-0.5 dB 20 Hz to 20 kHz, resolution 0.05 dB; Frequency: accuracy +/-1 %, precision +/-0.1 Hz,resolutionthelargerof1.5Hzor1/48octave;Time:accuracy+/-10.4μs,precision+/-0.5μs,resolution10.4μs;Angular:accuracy+/-1°,precision+/-0.5°,resolution0.5°. 5. Environment: Measurements time-windowed and processed to eliminate room effects, approximating an anechoic environment. Data processed as anechoic or fractional space, as noted. 6. Measurement Distance: 7.46 m. Acoustic responses represent complex summation of the subsystems at 20 m. SPL is referenced to other distances using the Inverse Square Law. 7. Enclosure Orientation:Forbeamwidthandpolarspecifications,asshowninMechanicalSpecificationdrawing. 8. Volts: Measured rms value of the test signal. 9. Watts:Peraudioindustrypractice,“loudspeakerwatts”arecalculatedasvoltagesquareddividedbyratednominalimpedance.Thus,thesearenotTrueWattunitsofenergyasdefined by International Standard. 10. SPL: (Sound Pressure Level) Equivalent to the average level of a signal referenced to 0 dB SPL = 20 microPascals. 11. Subsystem: This lists the transducer(s) and their acoustic loading for each passband. Sub = Subwoofer, LF = Low Frequency, MF = Mid Frequency, HF = High Frequency. 12. Operating Mode:Userselectableconfigurations.Betweensystemelements,acomma(,)=separateamplifierchannels;aslash(/)=singleamplifierchannel.DSP=DigitalSignalProcessor. IMPORTANT:Toachievethespecifiedperformance,thelistedexternalsignalprocessingmustbeusedwithEAW-providedsettings. 13. Operating Range: Range where the processed Frequency Response stays within -10 dB SPL of the power averaged SPL within this range; measured on the geometric axis. Narrow band dips are excepted. 14. Nominal Beamwidth: Design angle for the -6 dB SPL points, referenced to 0 dB SPL as the highest level. 15. Axial Sensitivity: Power averaged SPL over the Operating Range with an input voltage that would produce 1 W at the nominal impedance; measured with no external processing on the geometric axis, referenced to 1 m. 16. Nominal Impedance: Selected 4, 8, or 16 ohm resistance such that the minimum impedance point is no more than 20% below this resistance over the Operating Range. 17. Accelerated Life Test:MaximumtestinputvoltageappliedwithanEIA-426Bdefinedspectrum;measuredwithrecommendedsignalprocessingandRecommendedProtectionFilter. 18. Calculated Axial Output Limit: Highest average and peak SPLs possible during the Accelerated Life Test. The Peak SPL represents the 2:1 (6 dB) crest factor of the Life Test signal. 19. High Pass Filter: This helps protect the loudspeaker from excessive input signal levels at frequencies below the Operating Range.
GRAPHIC DATA 1. Resolution:Toremoveinsignificantfinedetails,1/12octavecepstralsmoothingwasappliedtoacousticfrequencyresponsesand1/3octavecepstralsmoothingwasappliedtothebeamwidthand impedance data. Other graphs are plotted using raw data. 2. Frequency Responses: Variation in acoustic output level with frequency for a constant input signal. Processed: normalized to 0 dB SPL. Unprocessed inputs: 2 V (4 ohm nominal impedance), 2.83 V (8 ohm nominal impedance), or 4 V (16 ohm nominal impedance) referenced to a distance of 1 m. 3. Processor Response: The variation in output level with frequency for a constant input signal of 0.775 V = 0 dB reference. 4. Beamwidth:Averageangleforeach1/3octavefrequencybandwhere,startingfromtherearoftheloudspeaker,theoutputfirstreaches-6dBSPLreferencedto0dBSPLasthehighestlevel.Thismethod means the output may drop below -6 dB SPL within the beamwidth angle. 5. Impedance: Variation in impedance magnitude, in ohms, with frequency without regard to voltage/current phase. This means the impedance values may not be used to calculate True Watts (see 9 above). 6. Polar Data: Horizontal and vertical polar responses for each 1/3 octave frequency band 100 Hz to 16 kHz or Operating Range.
LEGENDHPF: High Pass Filter for crossover –or– Recommended High Pass Filter.LPF: Low Pass Filter for crossover.LF/MF/HF: Low Frequency / Mid Frequency / High Frequency.AMP: User Supplied Power Amplifier –or– Integral Amplifier for NT products.XVR: Passive LPFs, HPFs, and EQ integral to the loudspeaker.EAW Focusing: Digital Signal Processor capable of implementing EAW Focusing.
JFL213 Specifications
Eastern Acoustic Works • One Main Street • Whitinsville, MA 01588 • tel 800 992 5013 / 508 234 6158 • fax 508 234 8251 • www.eaw.comAugust 2012Part Number: RD0732 Rev 100EAW products are continually improved. All specifications are therefore subject to change without notice.
INPUT PANEL REV: DESCRIPTION:
REVISIONS
A00 NEW ISSUE PER ECOWHT8897 MJC
DWG SPEC/INPUT JFL213
SCALE:
2038890-SDMJC 09/14/11DRAWING NUMBER:DATE:DRAWN BY:
1 of 1
1:1REV:
A00LOUD TECHNOLOGIES INC, ALL RIGHTS RESERVED
ONE MAIN STREET, WHITINSVILLE, MA 01588 USA
LOUD Technologies Inc.
TITLE:
SHEET:ADOBE ILLUSTRATOR
BI-AMP
SINGLE-AMPPIN 1PIN 1PIN 2PIN 2
PIN 1 LF
NCNC
LFPIN 1PIN 2 HF
HFPIN 2
BI-AMP
SINGLE-AMPPIN 1PIN 1PIN 2PIN 2
PIN 1 LF
NCNC
LFPIN 1PIN 2 HF
HFPIN 2
HF SHADING
MULTI BOX
SINGLE BOX
LONG THROW
BI-AMP
SINGLE-AMP
OPERATING MODEJFL213
JFL213 = 30 KG / 65 LBJFL213 RIGGING WORKING LOAD LIMIT (WLL): FIVE(5)
JFL213 IN SUCCESSION. 148 KG / 325LB FAILURE TO FOLLOW MANUFACTURER’S
INSTRUCTIONS CAN RESULTIN DAMAGE, INJURY, OR DEATH.
DESIGNED IN WHITINSVILLE, MA, USA. MANUFACTURED IN CHINA. ©2012 LOUDTECHNOLOGIES, INC. “EAW” IS A REGISTERED TRADEMARK OF LOUD TECHNOLOGIES, INC.
THIS PRODUCT HAS M10 MOUNTING POINTS. SEE OWNER’S MANUAL.
REVISIONSERIAL NUMBER
NLT4MP
NLT4MP
SIGNAL DIAGRAM
DSPEQ
DELAYHPF/LPF
OR“EAW FOCUSING”
AMP
2-Way, Bi-Amp (LF, HF)
AMP
HF
LF
HPF
2-Way, Single-Amp (LF/HF)
AMP XVR
HF
LF