Please check the pack contents before attempting to assemble this product. A full checklist of compo-nents is given in this leaflet. If any components are missing, please contact the John Lewis Helpline.
This product is HEAVY, it should be assembled as near as possible to the point of use. TAKE CAREWHEN LIFTING to avoid personal injury and (or) damage to the product.
This product takes approximately 90 MINUTES to assemble with 2 PEOPLE.
The fittings pack contains SMALL ITEMS which should be KEPT AWAY FROM YOUNG CHILDREN.
Read this leaflet in full before commencing assembly.
If you are missing some fittings (cams, dowels and screws) please contact our spare partshelpline on 0330 005 9435. Opening hours are 9am - 5pm Monday to Friday.For all other queries, please call John Lewis Customer support on 0345 604 9049
John Lewis
Stock Code: 80321704 - 80321304 - 80321804 - 80321504
Mixit tall wardrobe
Thank you for purchasing this Mixit wardrobe. Please read the instructions carefully before use to en-sure safe and satisfactory operation of this product.
Think about your Ceiling Height beforeassembling your TALL wardrobe.
To build the wardrobe horizontally youneed a minimum clearance of 2.44 Mheight.
To build the wardrobe vertically youneed a minimum clearance of 2.40 Mheight.
Please refer to page 6 for further information.
PRE-ASSEMBLY PREPARATIONPlease ensure instructions are read in full before attempting to assemble this product.
Necessary Tools
Screwdriver Rulertape measure Small hammer
DrillEye protection
Spirit level
MXT 60 rev. 04 - 19/07/17
Page 1
Metal dowel x 12 Cam lock x 12 Wooden dowel x 16
30mm
Wedge!x housing x 4 Wedge!x dowel x 4 Support foot x 4
Hanger rail support x 2 11mm Euroscrew x 4 15mm Screw x 2
Spacer x 2 x 2 Levelling Wedge x 2
Bumper x 4 25mm Nail x 50 27mm Connector x 4
4MAx15 Connect. screw x 4 hanging rail x 1 Nail guide x 1
clip hinge x 8 hinge mounting plate x 815mm screw x 16
A B C
G
L
H
M
R S P1
D E F
I
N
O P Q
T I U
Page 2
MXT 60 rev. 04 - 19/07/17
Fittings checklist
1
1
2
2
3
4
5
6
Page 3
MXT 60 rev. 04 - 19/07/17
Parts checklist
1
67
6
1
7
3332
70
70
Right side
left side
Bottom
Bottom
71
71
F
U
2
A
F
U
2
A
4544
U
U32
33
4445
Step by step assembly instructions
Step OneAttach 12x metal dowels (A) into the pre-drilled holes on side panels (2) as shown. Use a screwdriver toturn fitting (A) clockwise to fix.Attach 4x support foot (F) into pre-drilled holes on side panels (2) as shown.Attach 4x hinge mounting plate (U) into pre-drilled holes on side panels (2) as shown. Pay attention toplace central hinge at correct position.
1.
2.3.
Page 4
MXT 60 rev. 04 - 19/07/17
Page 5
MXT 60 rev. 04 - 19/07/17
C
BC
1 x 2
B
5
C C
6 Raw
Step by step assembly instructions
Step TwoAttach 4x wooden dowels (C) into the pre-drilled holes on top/bottom panels (1) as shown.Place the cam lock (B) into the holes on top/bottom panels (1) as shown, arrow pointing towards thebolt.
1.2.
Step ThreeAttach 8x wooden dowels (C) into the pre-drilled holes on rails (5) (6) as shown.1.
D
3
D
Step FourAttach 4x wedgefix housing (D) into the pre-drilled holes on shelf (3) as shown.1.
Choose Mounting Method:
STEP ELEVENSTEP FIVE
Horizontal VerticalMinimum 2.44 M ceiling height clearance required
Measure ceiling hight:
Not less than 2.40 M.
+2.44 M
2.40 M
X cm
Page 6
Step by step assembly instructions
MXT 60 rev. 04 - 19/07/17
1
1
2
5
6
1 2
B
B
A
Page 7
MXT 60 rev. 04 - 19/07/17
1
1
2
5
6
1 2
B
A
B
Step by step assembly instructions Horizontal Wardrobe Assembly
Step FiveAttach top/bottom panels (1) and rails (5) (6) onto right side (2) as shown. Ensure metal dowels (A) andwooden dowels (C) are aligned correctly with the holes of matching parts before attaching.Secure top/bottom panels (1) to right side panel (2) using a screwdriver to turn fitting (B) clockwise to fix.
1.
2.
Step SixAttach top/bottom panels (1) and rails (5) (6) onto left side (2) as shown. Ensure metal dowels (A) andwooden dowels (C) are aligned correctly with the holes of matching parts before attaching.Secure top/bottom panels (1) to right side panel (2) using a screwdriver to turn fitting (B) clockwise to fix.
1.
2.
Page 8
MXT 60 rev. 04 - 19/07/17
4
Step by step assembly instructions
Step SevenWith help of an assistant, carefully rotate the unit.
1.
Step EightPosition back panel (4) as shown.1.
Page 9
MXT 60 rev. 04 - 19/07/17
P
P
P
Important:The cabinet MUST be ‘square’ when theback is attached.
4P1
Step by step assembly instructions
Step NineAttach back panel (4) onto back side of the unit using 50x nails (P), with the help of the nail guide (P1).1.
STEP FOURTEEN
Step TenWith help of an assistant, carefully stand up the unit upright.1.
1
1
2
5
6
2
B
1
A
B
C
Page 10
Step by step assembly instructions Vertical Wardrobe Assembly
Step ElevenAttach top/bottom panels (1) and rails (5) (6) onto left side (2) as shown. Ensure metal dowels (A) andwooden dowels (C) are aligned correctly with the holes of matching parts before attaching.Secure top/bottom panels (1) to right side panel (2) using a screwdriver to turn fitting (B) clockwise to fix.
1.
2.
MXT 60 rev. 04 - 19/07/17
1
1
2
2
B
6
1
A
B
C
Page 11
MXT 60 rev. 04 - 19/07/17
Step by step assembly instructions
Step TwelveAttach top/bottom panels (1) and rails (5) (6) onto left side (2) as shown. Ensure metal dowels (A) andwooden dowels (C) are aligned correctly with the holes of matching parts before attaching.Secure top/bottom panels (1) to right side panel (2) using a screwdriver to turn fitting (B) clockwise to fix.
1.
2.
P
P
4
Important:The cabinet MUST be ‘square’ when theback is attached.
P1 P1
1 2
Page 12
Step by step assembly instructions
Step ThirteenPosition back panel (4) as shown.Attach back panel (4) onto back side of the unit using 50x nails (P), with the help of the nail guide (P1).
1.2.
MXT 60 rev. 04 - 19/07/17
Page 13
MXT 60 rev. 04 - 19/07/17
Step by step assembly instructions
Ø5mm
RQ
Step FourteenUse 2x levelling wedge (N) to level the unit.1,
Step FifteenFittings have been supplied in order to join units together.Place units together in their final positon.Decide position where to drill through using a Ø5 mm bit.Push the Connector (Q) into the hole and then screw Bolt (R) in from the other side, tighten with ascrewdriver.
1.2.3.
N
N
L
MI
Wall plug and screw
not included.
Please see Guide to
wall mounting
20 mm
M
I
L
Page 14
MXT 60 rev. 04 - 19/07/17
Step by step assembly instructions
Step SixteenTo prevent possible overbalancing we recommend that this unit is secured to a suitable wall by use of two ‘L’Brackets (M) fitted to the Top of the unit.
Fix the Brackets (M) loosely onto the top of the unit using spacer (L) screw (I) and mark the wall for the wall fix-ing.Swivel the Bracket (M) away from the wall and drill a hole in the wall using a suitable drill bit and fit your wallfixing. Swivel the Bracket (M) back and fix the Bracket to the wall, then tighten Screw (I)
! IMPORTANT !Take care when drilling the wall that you do not drill into any pipes, wires etc. If in doubt, consult an expert.
Wall plug and screw not included. See wall fixing guide at page 14.
1.
2.
3.
E
E
3
G
HS
3
S
22
Recommended loading capacity:Single shelf: 20 KgsDouble shelf: 16 Kgs
Page 15
Step by step assembly instructions
Step SeventeenChose shelf (3) and hanging rail (S) position. Fix 2x hanger rail supports (G) onto the side panels (2) using the screws (H). Fit the hanging rail (S) onthe rail supports (G) as shown.Fix 4x shelf support (E) onto the side panels (2). Position the shelf on the shelf support as shown.
1.2.
3.
MXT 60 rev. 04 - 19/07/17
T
TI
I
T
T
I
I
O
O
O
x 2
T
U
CLICK
PUSH
Page 16
MXT 60 rev. 04 - 19/07/17
Step by step assembly instructions
Step EighteenFix 4x hinges (U) to each door using 15 mm screws (I). Repeat with all the doors.1.
Step NineteenHang the clip hinge (T) to the hinge plate (U). Click them together.To remove the door push the clip hinge button and remove the door carefully.
1.
LATERAL ADJUSTMENTby screw adjustment.
FRONT-TO-BACKby slackening and re-tighteningthe hinge-arm mounting screw.
VERTICAL ADJUSTMENTvia slot on mountingplate by slackening andre-tightening the screwson mounting plate
Page 17
MXT 60 rev. 04 - 19/07/17
HINGE ADJUSTMENT INSTRUCTIONS
WoodIf �xing to woodmake su re that itisn't chipboard asscrews can easilypull away from thecore structure
Brick or MasonryUse an appropriatewall plug provided youare sure your wall issound.
Cavity wallSpecial togglewall plugs areneeded. Seekexpert advice.
Page 18
Wall fixing - if in doubt seek professional advice
Care and Maintenance
MXT 60 rev. 04 - 19/07/17
This product has been manufactured using modern manufacturing methods and materials.
To keep your product, looking at its best, we strongly recommend either dusting with a soft cloth, orthe use of a damp (not wet ) cloth and water containing no more than a 5% soap solution. Dry with a soft clean cloth.
Aggressive chemicals, such as wax furniture polish, abrasive cleaners, bleach or hypochlorate (chlorine)based cleaners, multi purpose cleaners, dilutes, acetone, alcohol and solvent based liquid product shouldNOT be used, as may result in damage.
Page 19
MXT 60 rev. 04 - 19/07/17
Safety Instructions
Never drag furniture when moving it, always lift it.Periodically check all fixings to ensure none have come loose and re-tighten when necessary.Please take care when handling or moving the furniture as careless handling may cause damage or injury.Furniture can be dangerous if incorrectly installed. Assembly should be carried out by a competent person. Noliability will be accepted for damage or injury caused by incorrectly installed or assembled furniture.
It is recommended that before moving a heavy object to a new location it is completely dis-assembled to avoidpersonal injury or damage to the furniture. Please be careful to retain all fittings when doing this.
It is recommend by John Lewis that this product is fixed securely to a wall. However this is not compulsory.No liability will be accepted for damage or injury caused by inadequate fixing or use without fixing.
PLEASE KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE
John Lewis Partnership 171 Victoria Street London SWIE 5NNwww.johnlewis.com