JSP_PLIST_10_RESPIRATORY

Qualitative Fit Testing

Quantitative Fit Testing

Qualitative Fit Testing can be used on

what are defi ned as tight fi tting respirators,

with the exception of full face masks.

Within the JSP Respiratory Protective

Equipment range these products are :-

• Moulded Disposable Dust Masks

• Vertical Fold Flat Dust Masks

• Tradesman 2 and 3

(fi tted with dust fi lters)

• Midimask Half Mask


• Maximask Half Mask


• Maximask 2000 Half Mask


Full face masks cannot be tested because

the test hood is not large enough for the

mask fi tted with a fi lter. For testing this

product it will be necessary to use the

Quantitative method (discussed below).

Qualitative Fit Testing can be used not

only as a test method to ensure your

employees are properly protected; but

also as a very effective way of training

them in the correct way of fi tting a mask.

Dust and half masks commonly fail to do

the job they are intended to do because

of poor fi tting and care by the user.

The seal between the face

and the edge of the mask

is the most common problem

area. You will also see

users using a mask after

having kept it on their

head or hanging round the

neck.

The test employs a hood

to create a small test

chamber around the users

head, and a test solution.

This test solution has a

bitter taste. It is the same

type of solution that is

put on childrens toys

and fingernails to stop

them chewing them. As

the test uses these two

consumable parts and is

designed to be carried out

by the employer; it is a

very cost effective solution

for assessing the ability of the selected

Respiratory Protective Equipment and the

training given to protect the employee.

JSP offer a Quantitative Fit Testing

service that can be carried out at the

employers site. The service can not only

check how well protected the employers

staff are but also offer training in the

correct fi tting and care of the respirator

being tested.

Quantitative Fit Testing can be used on all

tight fi tting respirators including full face

masks. This means it is suitable for testing

all JSP Respiratory Protective Equipment

except; PowerCap, Jetstream and Air Fed.

However generally speaking this method

will not be used when disposable dust

masks are the RPE being used. JSP use the

Portacount from TSI to carry out on-site

Quantitative Fit Testing. This is an easily

portable particle counting device that has

been developed in the United States of

America. It has been well tested in this

market over many years. Unlike in the EU,

masks in the US are only tested for their

fi ltering effi ciency and not on a selection

of users to check the inward leakage of

contaminants as we do in the EU. The

problem with any standards testing is

that it cannot take into account the large

variation in the shapes of peoples faces

and therefore it is important to know that

a mask actually fi ts the wearers face.

With all Respiratory Protective Equipment,

the most common problem is the fi t of

the mask to the wearers face and the

care taken of the mask. Quantitative

Fit Testing is a very effective, and

importantly, measurable way of ensuring

that the user has a mask that will give

him/her adequate levels of protection.

Portacount works by comparing the

particles outside a wearers mask, with

those inside it, that have got past the

face seal. JSP’s Respiratory Technicians

will fi rst check that there is a suitable

number of particles in the area that the

masks are to be tested in.

At the end of the test, a report is produced

for inclusion in the employee’s records.

While this report is being printed JSP’s

Respiratory Technician will give the

wearer instructions in the care of his/her

respirator.

Quantitative Fit Testing provides the

employer with a measurable result for a

particular mask on a particular employee

and is therefore an extremely important

part of an effective Health and Safety

programme.

Please contact 01993 826050 or email

[email protected] to arrange

for a site visit from one of JSP’s

Respiratory Technicians.

RESPIRATORY PROTECTION - FIT TESTING

Call: 01993 826000 www.jsp.co.uk [email protected] [email protected]

CODE DESCRIPTION CARTON QTY

BPT050-000-000 Qualitative Fit Testing -

To determine the required APF it is simply a matter of dividing the measured level of concentration by the Workplace Exposure

Limit (WEL) that the local legislation allows. This calculation will give a required protection factor, selection is then just to ensure

that the APF for the RPE selected is above the Required. If when selecting RPE their is any question, then a quick call to JSP’s

Technical Helpline on +44(0)1993 826051 will help you solve any queries.

Whether or not a mask/fi lter/respirator is suitable can be determined by using the following calculation:

Required protection factor (RPF) = Measured level of contamination

Exposure limit for contaminateFor example:

RPF = 250mg/m³ 50mg/m³ RPF = 5

Therefore a respiratory device with an APF of 10 would be required (see shaded row above)

Respiratory protection is required where the wearer may encounter one of the following six forms of hazard in the workplace:-

DustFormed by the breaking down of solid materials, normally when materials are altered. For example, sanding, cutting, grinding and brushing. In general the smaller the dust particle the greater the hazard that it presents. Fibres from materials should also be treated as dusts.

MistFormed by processes that involve atomisation (such as spraying, cleaning and cutting/grinding using coolants) and consist of tiny liquid droplets rather like steam in a bathroom.

FumeFormed by the vapourisation of a solid material by the application of intense heat. Extremely fi ne particulates are formed as the fume cools and condenses. Many processes form fume; such as smelting, pouring metals and many welding applications.

VapourA gaseous state formed by evaporation

from substances that are normally either solid or liquid at room temperature. Generally released at room temperature (petrol, methalated spirits), many industrial processes, used in degreasing vapourise particularly quickly once heated.

GasAn air like substance at room temperature. Gases can travel far, very quickly.

Oxygen Defi ciency /Enrichment When an atmosphere is likely to contain less than 19% oxygen (or where conditions may exist in the future to cause this to happen); and in certain circumstances where the risk may be oxygen enrichment, which can lead to explosion and severe impairment of operatives.NOTE: Conventional respirators DO NOT protect the wearer from these hazards.

Respiratory Protection Requirements

Assigned Protection Factors

Assigned Protection

Factor

1/2 or 1/4Mask Plus Filter

Compressed air line

Valved Filtering1/2 Mask

Filtering1/2 Mask

Full FaceMask Plus Filter

Powered Filtering: Helmets and Hoods

EN140 EN270 EN405 EN149 EN136 EN12941

4 P1 - FMP1 FFP1 P1 -

10

P2

Gas X

Gas X +P3

-

FMP2

FMGas X

FMGas X +P3

FFP2 P2 TH1

All Face-Pieces

20 P3 FMP3 FFP3 Gas X

Gas X + P3

TH2

All Face-Pieces

40 - Continuous fl ow

hood & faceshield - - P3

TH3

Semi-hood,

Hood Blouse,

Semi-Blouse

www.jsp.co.uk [email protected] [email protected] Call: 01993 826000 25

RESPIRATORY PROTECTION REQUIREMENTS - RESPIRATORY PROTECTION

CBB610-211-100 Switch & Go Unit 8 Hour EN12941 : 1999 TH2PSL - UK PLUG 1

CBB610-311-100 Switch & Go Unit 8 Hour EN12941 : 1999 TH2PSL - EURO PLUG 1

Jetstream™ Switch & Go Unit (Standard Dust Version) The Jetstream Switch & Go is the fi rst low cost fully approved unit to EN12941, which features ALL the equipment

needed in one complete pack. Jetstream™ is a belt mounted rechargeable respirator with a large capacity disposable dust

fi lter. The waist belt and power unit weighs just 765g. Jetstream™ delivers 180 lt/min of air through the fi lter via a highly

fl exible hose to the desired headtop. The Switch and Go unit comes complete with a white nylon head top. Jetstream Switch & Go pack Contains: PSL Filter, Hose, Charger, Carry Case, Battery, White Nylon Headtop, Flow Meter & UK

Plug. Filter Performance: Offers an assigned protection factor (APF) of 20 x Work place Exposure Limit (WEL) for very fi ne

dusts, fi bres, fumes and aqueous mists.

CCA630-211-100 Jetstream Gas/Vapour GV-X Switch & Go c/w A2 Filter - UK PLUG 1

CCA630-311-100 Jetstream Gas/Vapour GV-X Switch & Go c/w A2 Filter - EURO PLUG 1

CCA620-211-100 Jetstream Gas/Vapour GV-X Switch & Go c/w A2PSL Filter - UK PLUG 1

CCA620-311-100 Jetstream Gas/Vapour GV-X Switch & Go c/w A2PSL Filter - EURO PLUG 1

Jetstream™ Switch & Go™ Gas/Vapour GV-X Version (Complete with white nylon headtop)A2 or A2PSL Filter, Hose, Charger, Carry Case, Battery, White Nylon Headtop, Flow Meter & UK Plug.

Filter Performance: Offers an assigned protection factor (APF) of 20 x Work place Exposure Limit (WEL)

for organic vapours and gases and for very fi ne dusts, fi bres, fumes and aqueous mists.

CBU220-001-100 Jetstream 8 hour Waist Mounted Power Unit c/w TH2SPL Filter - UK PLUG 1

CBU220-301-101 Jetstream 8 hour Waist Mounted Power Unit c/w TH2SPL Filter - EURO PLUG 1

CBU231-201-100 Jetstream Gas/Vapour GV-X 8 Hour Waist Mounted Power Unit c/w A2 Filter - UK PLUG 1

CBU231-301-100 Jetstream Gas/Vapour GV-X 8 Hour Waist Mounted Power Unit c/w A2 Filter - EURO PLUG 1

CBU233-201-100 Jetstream Gas/Vapour GV-X 8 Hour Waist Mounted Power Unit c/w A2PSL Filter - UK PLUG 1

CBU233-301-100 Jetstream Gas/Vapour GV-X 8 Hour Waist Mounted Power Unit c/w A2PSL Filter - EURO PLUG 1

Jetstream™ Waist Mounted Units Complete with Filter & Charger Only (No headpiece supplied)The Jetstream Waist Mounted Unit can be purchased separately to allow it to be combined with an alternative Jetstream

headpieces to provide additional protection to the head, eyes and face.

A2 Filter

A2PSL Filter

RESPIRATORY PROTECTION - JETSTREAM™ POWERED AIR RANGE



JETSTREAM™ SWITCH & GO™ UNIT

1

4

WAIST MOUNTED UNITBlower unit with fully automatic

alarm and integrated battery

providing 180 LT/min of fi ltered air

HEADPIECEA variety of headpieces available to

suit a range of applications

SUPPLY HOSEReinforced hose to prevent kinking

FILTERSChoice of fi lters for different uses

1

2

4

3

JETSTREAMSWITCH & GO



SW

ITCH AND

GO

SW

ITCH AND

GO

2

3RI

GHTS RESERVED

DESIGN REGISTERED

a

b

c

d

efg

CBU210-001-100 Waist Mounted Power Unit Only (PSL) for Dust Filter only (No fi lter or charger) 1

CBU211-001-100 Waist Mounted Power Unit Only (G-VX) for Gas Filters (No fi lter or charger) 1

CBU610-000-000 Standard Jetstream PSL Spare Filter 1

CBU620-000-000 Gas/Vapour GV-X A2PSL Spare Filter 1

CBU630-000-000 Gas/Vapour GV-X A2 Spare Filter 1

CBU120-000-000 Spare Charger - UK 1

CBU130-000-000 Spare Charger - EURO 1

CBU020-001-100 Long Jetstream Hose 1

CBU300-001-100 Airfed Replacement Hose 1

CBU010-001-100 Bayonet Fitting 1

CBU150-001-100 Replacement Skirt for Jetstream™ Helmet 1

CBU160-001-300 Replacement Visor for Jetstream™ Helmet 1

CBU170-001-100 Replacement Skirt for Jetstream™ Faceshield 1

CBU180-001-300 Replacement 20cm Slim P/C Visor-Jetstream™ Faceshield 1

CBU240-000-500 Translucent Blue Splash Cover for Jetstream™ Filter 1

Jetstream™ Spares Spares to maintain Jetstream as a highly effective respiratory product.

CBH050-000-000 Jetstream Clear PVC Hood 1

Jetstream™ Alternative Headpiece Clear PVC HoodFor pharmaceutical and high visibility work. The semi rigid visor allows a high optical clarity, ideal for clean room

environments. Conforms to BS EN 12941:1999

CBH040-000-000 Jetstream Non-Woven Hood 1

Jetstream™ Alternative Headpiece Non-Woven HoodLightweight hood with clear non impact visor, designed for semi disposable applications. Conforms to

BS EN 12941:1999

CBH010-000-000 Jetstream MK7 1

Jetstream™ Alternative Headpiece MK 7 Helmet with VisorHDPE industrial safety helmet to EN397 for protection against falling hazards with sealed visor.

Conforms to BS EN 12941:1999 TH2 Polycarbonate visor gives protection to EN 166.1.B.3.9

CBH030-000-000 Jetstream White Nylon Hood 1

Jetstream™ Alternative Headpiece White Nylon HoodMore sturdy than the Non Woven hood but still lightweight. White for most industrial environments.

Conforms to BS EN 12941:1999

CBJ031-001-100 Jetstream™ AIRFED COBRA * DIN 9-13 Airfed Cobra Welding 1

CBJ011-001-100 Airfed Welding/Grinding Visor DIN 9-13 1

CBJ020-001-300 Airfed Grinding Visor Only 1

i. Jetstream™ Airfed CobraDesigned to attach to the JSP Jetstream™ powered air unit. The Airfed Cobra™ has a uniquely developed

highly effi cient yet quiet air fl ow system through which 180 Ltrs per minute of fi ltered air is delivered.

Conforming to EN 12941 :1999. Designed to be the most cost effective powered air shade 9-13 auto

darkening fi lter (ADF) welding helmet on the market. Also available with a grinding visor.

Airfed

Welding/Grinding

Airfed

Grinding Visor


JETSTREAM™ POWERED AIR RANGE - RESPIRATORY PROTECTION

JETSTREAM™ ALTERNATIVE HEADPIECES


a

b

c

d

e

f

g

CAD602-21A-100 PowerCap® Lite ip - 8 hour re-chargeable - Wipeable Lite UK Plug (Made to order) 1

CAD602-31A-100 PowerCap® Lite ip - 8 hour re-chargeable - Wipeable Euro Plug (Made to order) 1

PowerCap® Lite ip WipeableAll the benefi ts of the Powercap lite plus the benefi ts of being easily wiped clean in a hygienic manner.

Conforms to EN 166, EN812, EN12941 TH1P

CAU020-001-100 Cap Black 1

CAU140-000-000 Powercap® Charger with UK plug 1

CAU130-000-000 Powercap® Charger with Euro plug 1

CAU110-000-000 Powercap® Charger with US plug 1

CAU610-000-010 Powercap® prefi lter Packs 1

CAU601-001-100 Filter TH1P (per pair) Black 1

CAU030-000-000 Standard Visor Kit 1

CAU080-000-000 Impact Protection Visor Kit 1

CAU070-001-100 Face Seal 1

CAU150-000-000 Peel Off Visor for Powercap®(Pack of 10) 10

PowerCap® SparesSpares to keep Powercap providing optimal levels of protection.

CAD601-201-100 PowerCap® Lite - 4 hour re-chargeable UK Plug - Black 1

CAD601-211-100 PowerCap® Lite - 8 hour re-chargeable UK Plug - Black 1

CAD601-301-100 PowerCap® Lite - 4 hour re-chargeable Euro Plug - Black 1

CAD601-311-100 PowerCap® Lite - 8 hour re-chargeable Euro Plug - Black 1

PowerCap® LiteThe Powercap Lite incorporates lithium ion batteries derived straight from the latest mobile telephone battery technology.

This has enabled the battery to be incorporated within the headpiece, so it is completely self-contained without any ancillary

battery pack. It provides the wearer with a greater feeling of freedom and ease of use, and will provide a consistent airfl ow

of 160 litres a minute for 4 or 8 hours continuously, with only 440g head weight. Conforms to EN12941 TH1P

CAD602-201-100 PowerCap® Lite ip - 4 hour re-chargeable UK Plug - Black 1

CAD602-211-100 PowerCap® Lite ip - 8 hour re-chargeable UK Plug - Black 1

CAD602-301-100 PowerCap® Lite ip - 4 hour re-chargeable Euro Plug - Black 1

CAD602-311-100 PowerCap® Lite ip - 8 hour re-chargeable Euro Plug - Black 1

PowerCap® Lite ip - Impact Protection A Powercap Lite incorporating BumpCap protection and and Impact Faceshield. Conforms to EN 166, EN812, EN12941 TH1P

RESPIRATORY PROTECTION - POWERCAP® POWERED AIR RANGE


POWERCAP® LITE & IP LITE


POWERED AIRGives a cooling, comfortable supply of fi ltered air

at 160 litres/minute. Equivalent to FFP2 levels

with an Assigned Protection Factor (APF) of 10

BUMP CAP PROTECTIONBump Cap Protection to EN812. Ideal for working

in confi ned spaces when there is a danger of

bumping or scraping the head

RECHARGEABLE BATTERIESLithium Re-chargeable 4 or 8 hour batteries

IMPACT PROTECTIONPowercap ip gives eye and face impact protection

to EN166 1B Ideal for working where there is a

danger of fl ying particles

1

2

4

3

1

2

3

4 RIGH

TS RESERVED

DESIGN REGISTERED

HEAD HARNESSAdjustable headpiece to get best possible fi t and comfort.

HOOD SEALHood to seal breathing area and to ensure high levels of

wearer comfort and cleanliness.

FACESHIELDHigh performance headpiece incorporates the proven JSP

Invincible faceshield with acetate or polycarbonate visor.

REGULATORPreset regulator incorporating fl ow warning gauge with

integrated high effi ciency coalescent fi lter.

1

2

4

3


ILES OPTICAL® AIRFED RANGE - RESPIRATORY PROTECTION

G-N-AF-KitBrowguard, harness, Visor, air tube & diffuser, face seal, neck cover,

Waistbelt with carbon fi lter regulator, visor cover and storage bag1

G-N-AFB-A Browguard, harness, Visor, air tube & diffuser, face seal, neck cover. 1

Airfed Faceshield The airfed faceshield meets all requirements of EN 270, features a preset regulator to ensure that the wearer receives a

continuous fl ow of 160-230 Ltr / min to faceshield head piece with a protection factor of up to 200.


BUA080-000-000 Wall Mounted Single Man Filter Unit 1

BUA100-000-000 Carbon Cartridge for Wall mounted Unit 1

Wall Mounted Single Man Filter UnitRequired where the compressed air supplied is not of breathable quality. The three-stage fi ltering removes large particles,

then oil mists, water and submicron particles, the fi nal fi lter removing any remaining oils.

G-N-AF-W-R-CF-Y Belt Regulator: Waistbelt c/w Carbon cartridge, air fl ow regulator, Q/R connector, Y piece 1

G-CC-CE Carbon Cartridge for Belt Regulator 1

Belt Regulator and Filter Assembly Belt with pocket regulator and coalescent fi lter to remove low levels of moisture and oil.

G-N-AFB Spare Browguard 1

G-N-AF-A170 Acetate Visor - 17cm 4

G-N-AF-BT Air Tube with diffuser 1

G-N-AF-HYGKIT Hygiene Kit - 5 x face seal, 5 x Sweatbands 1

G-N-AF-VC10 Disposable Visor Cover (pack 10) 1

G-N-AF-NC Fabric neck cover 5

G-N-AF-BAG Fabric storage bag 1

Replacement PartsUser replaceable parts to maintain the faceshield’s high performance.

1

2

3

4

AIRFED RANGE

RESPIRATORY PROTECTION - OLYMPUS® FULL FACE


Olympus® Silicone Full Face Mask - BlackModern design which features a completely clear visor design increasing

light levels within the mask and decreasing the feeling of claustrophobia

often experienced using full face masks. The Silicone construction

increases user comfort. It has a wide scratch resistant polycarbonate

visor and a lightweight centre canister connector for optimum balance.

The 5 point suspension harness and chin recess ensure a comfortable and

a stable fi t. Conforms to EN136

BPA000-011-000 Silicone Full Face Mask - Black 1

BMV210-000-000 A2 - DIN Thread Filter Canisters 22 x 3

BMV230-000-000 B2 - DIN Thread Filter Canisters 22 x 3

BMV270-000-000 K2 - DIN Thread Filter Canisters 22 x 3

BMV310-000-000 A2P3 - DIN Thread Filter Canisters 22 x 3

BMV340-000-000 ABEK2 - DIN Thread Filter Canisters 22 x 3

BMV360-000-000 ABEK2P3 - DIN Thread Filter Canisters 22 x 3

BMV370-000-000 AB2P3 - DIN Thread Filter Canisters 22 x 3

BMV430-000-000 AB2 - DIN Thread Filter Canisters 22 x 3

BMV390-000-000 P3 - DIN Thread Filter Canisters 22 x 3

Olympus® DIN Thread Canister FiltersA full range of quality multi-fi t DIN thread Filter Canisters giving protection

against either gases, particulates or a combination of the two. Colour coded to

European norms in EN 14387 & EN 143

OLYMPUS® FULL FACE MASKS


BPE000-011-000 Rubber Full Face Mask - Black 1

Olympus® Rubber Full Face Mask - BlackA well balanced rubber full face mask designed to accept JSP DIN

Canisters and other Canister fi lters using standard EN 148-1 (DIN)

thread connection. It features a wide scratch resistant polycarbonate

visor and a lightweight centre canister connector for optimum balance.

The 5 point suspension harness and chin recess ensure a comfortable,

stable fi t. Conforms to EN136.

Filter TypeType Colour Code DescriptionA Organic Vapours and Gases with boiling point 65°C and above

B Inorganic Vapours and Gases (excluding Carbon Dioxide/Monoxide)

E Sulphur Dioxide and Other Acidic Vapours and Gases

K Ammonia and Ammonia Derivatives Vapours and Gases

ABEK Combination fi lter, all of the above

P Dust/Particle

Filter Classifi cationClass Dust Gas Vapor1 Low Effi ciency Low Capacity

2 Medium Effi ciency Medium Capacity

3 High Effi ciency High Capacity


31

MAXIMASK 2000™ HALFMASK RANGE - RESPIRATORY PROTECTION

BHS383-005-800 Maximask 2000 - 2x P2 Filters - Blue 24

BHS393-005-800 Maximask 2000 - 2x P3 Filters - Blue 24

BHS213-005-800 Maximask 2000 - 2x A1 Filters - Blue 24

BHS193-005-800 Maximask 2000 - 2x A2 Filters - Blue 24

BHS263-005-800 Maximask 2000 - 2x K1 Filters - Blue 24

BHS333-005-800 Maximask 2000 - 2x ABEK1 Filters - Blue 24

BHS323-005-800 Maximask 2000 - 2x AB1 Filters - Blue 24

BHS543-005-800 Maximask 2000 - 2x AB1 Filters and P2 Pre-Filters - Blue 24

BHS553-005-800 Maximask 2000 - 2x A1 Filters and P2 Pre-Filters - Blue 24

BHS303-005-800 Maximask 2000 - 2x A2P3 Combination Filters - Blue 24

BHS423-005-800 Maximask 2000 - 2x AB1P3 Combination Filters - Blue 24

BHS523-005-800 Maximask 2000 - 2x ABEK1P3 Combination Filters - Blue 24

Maximask 2000™ c/w Filter Cartridges in Clam Shell packagingA premium half mask offering protection and comfort. A unique, extra wide sealing surface offers

unparalleled comfort and fi t. Available in durable thermoplastic rubber. Masks are supplied with low

profi le fi lters with push and quarter turn fi tting. Packed in clam shells.

Maximask 2000™ Replacement Cartridges and Filters (sold in pairs)Replacement fi lter with unique Maximask 2000 fi tting. Filters perform to EN143 and

EN14387. Available in both clam shell and hanging bag.

BHS003-005-000 Maximask 2000 - Blue supplied boxed without cartridges 48

Maximask 2000™ without Filter CartridgesMask supplied without fi lters to allow purchaser to select the fi lter or range of fi lters

required for a particular application.

MAXIMASK 2000™ HALF MASKS


CODE (CLAM SHELL)

QTY(PAIRS)

CODE (BAGGED)

QTY(PAIRS) DESCRIPTION

COMFORTDurable thermoplastic rubber mask for superior fi t to most face shapes.

HARNESSFully adjustable four point cradle suspension ensuring an effective facial fi t.

VALVELow resistance exhalation valve for easy breathing, with stable mask confi guration

FILTERLow profi le angle fi lter design for minimum visual impairment.

1

2

4

3

1

3

2

4

BMH380-011-000 56 BMH380-011-700 80 P2 Dust Cartridge

BMH390-011-000 40 BMH390-011-700 80 P3 Dust Cartridge

BMT380-000-900 56 BMT380-000-700 80 P2 Pre Filter Pack (2 Covers & 2 Filters)

BMH210-011-000 40 BMH210-011-700 80 A1 Organic Vapour Cartridge

BMH190-011-000 40 BMH190-011-700 80 A2 Organic Vapour Cartridge

BMH260-011-000 40 BMH260-011-700 80 K1 Ammonia Cartridge

BMH320-011-000 40 BMH320-011-700 70 AB1 Organic & In-Organic Cartridge

BMH330-011-000 40 BMH330-011-700 70 ABEK1 Combination Vapour Cartridge

BMJ540-011-000 40 BMJ540-011-700 70 AB1 P2 Organic & In-Organic Vapour & Dust Cartridge

BMJ550-011-000 40 BMJ550-011-700 80 A1 P2 Organic Vapour Dust Cartridge

BMJ300-011-000 40 BMJ300-011-700 70 A2P3 Organic Vapour & Dust Cartridge

BMJ420-011-000 40 BMJ420-011-700 70 AB1P3 Organic & In-Organic Vapour & Dust Cartridge

BMJ520-011-000 40 BMJ520-011-700 70 ABEKP3 Combination Vapour & Dust Cartridge

www.jsp.co.uk [email protected] [email protected] Call: 01993 826050

RESPIRATORY PROTECTION - FILTERSPECTM RANGE


FULLY ADJUSTABLEFully adjustable spectacle frame for maximum comfort and security.

LIGHTWEIGHTLightweight re-usable fi lter holder element for an economic PPE solution.

FILTER MASKExhale valve is fi tted to reduce heat &

CO2 buildup for greater comfort.

PERFECT FITComfortable fi t and no steaming.

1

2

3

FILTERSPEC™ -

FilterSpec™ White with 3 Filters, Clear Lens The unique FilterSpecTM effortlessly combines both eye & respiratory protection. The one-piece lens

offers optimal coverage and has Anti-Mist and Anti-Scratch coating as standard. FMP2 fi ltration giving

94% effi ciency. Includes white holder, 3 fi lters and spectacle with Clear HC & Anti-Mist Lens.

CODE (CLAM SHELL)

CODE (BOXED)

DESCRIPTION CARTON QTY

ASF02B-100-100 10 FMP2 Filters 20

ASG02B-100-100 10 FMP2 Valve Filters 20

ASG04B-100-100 10 FMP2 Odour Valve Filters 20


FilterSpec™ - White Replacement Filters Pack of 10Replacement Filters for the FilterSpec & FilterSpec Pro

FILTERSPEC™ REPLACEMENT FILTERS - WHITE

SPECTACLE• Stylish spectacle element design.

• Fully adjustable spectacle frame for maximum

comfort and security.

• 6.5 base, one-piece lens offers optimal coverage.

• Anti-Mist Coating on Lens as standard.

• Anti-Scratch Coating on Lens as standard.

• Wide range of lens coatings available.

• Wide range of colour combinations available.

Spectacle Conforms to: EN166.1.F

FILTER MASK• Disposable fi lter mask element for optimum protection.

• Re-usable fi lter holder element for an economic PPE solution.

• Lightweight for user comfort. (Under 60g)

• Exhale valve fi tted for increased fi lter element longevity.

• Each product comes supplied with 3 fi lter elements.

• Removable, replaceable elastic strapping.

Mask Conforms to: EN1827:1999:+A1:2009

FILTERSPEC™ - WHITE


THE ONLY APPROVED COMBINATION EYE & RESPIRATORY PROTECTION IN THE WORLD

4

NEW1

2

3

PATE

NT PENDING

DESIGN REGISTERED

ASF129-120-100 ASF124-120-100 FilterSpecTM White with FMP2 Filter (Clear Lens) 20

ASG129-120-100 ASG124-120-100 FilterSpecTM White with FMP2 Valve Filter (Clear Lens) 20

ASG149-120-100 ASG144-120-100 FilterSpecTM White with FMP2 Odour Valve Filter (Clear Lens) 20

ASG139-120-100 ASG134-120-100 FilterSpecTM White with FMP3 Valve Filter (Clear Lens) 20

AGB120-201-100 FilterSpecTM Pro Black with FMP2 Filter (Clear Lens) 20

AGE120-201-100 FilterSpecTM Pro Black with FMP2 Valve Filter (Clear Lens) 20

AGE150-201-100 FilterSpecTM Pro Black with FMP2 Odour Valve Filter (Clear Lens) 20

AGE130-201-100 FilterSpecTM Pro Black with FMP3 Valve Filter (Clear Lens) 20

FilterSpec™ Pro - Black with 3 Filters, Clear Lens - (Boxed) The unique FilterSpecTM effortlessly combines both eye & respiratory protection. The one-piece lens

offers optimal coverage and has Anti-Mist and Anti-Scratch coating as standard. Includes black

holder, 3 fi lters and goggle with Clear HC & Anti-Mist Lens.

FilterSpec™ - Black with 3 Filters, Clear Lens The unique FilterSpecTM effortlessly combines both eye & respiratory protection. The one-piece lens

offers optimal coverage and has Anti-Mist and Anti-Scratch coating as standard. FMP2 fi ltration giving

94% effi ciency. Includes black holder, 3 fi lters and spectacle with Clear HC & Anti-Mist Lens.

ASF02B-101-100 10 FMP2 Filters 20


ASG04B-101-100 10 FMP2 Odour Valve Filters 20


FilterSpec™ - Black & FilterSpec Pro - Black Replacement Filters Pack of 10Replacement FiltersTM Black


FILTERSPECTM RANGE - RESPIRATORY PROTECTION

FILTERSPEC™ - BLACK

CODE (CLAM SHELL)

CODE (BOXED)


FilterSpec™ - Black with 3 Filters, Smoke Lens Includes black holder, 3 fi lters and spectacle with Smoke HC & Anti-Mist Lens.


FILTERSPEC™ PRO - BLACK

FILTERSPEC™ REPLACEMENT FILTERS - BLACK


ASF129-121-100 ASF124-121-100 FilterSpecTM Black with FMP2 Filter (Clear Lens) 20

ASG129-121-100 ASG124-121-100 FilterSpecTM Black with FMP2 Valve Filter (Clear Lens) 20

ASG149-121-100 ASG144-121-100 FilterSpecTM Black with FMP2 Odour Valve Filter (Clear Lens) 20

ASG139-121-100 ASG134-121-100 FilterSpecTM Black with FMP3 Valve Filter (Clear Lens) 20

CODE (CLAM SHELL)

CODE (BOXED)


ASF129-125-800 ASF124-125-800 FilterSpecTM Black with FMP2 Filter (Smoke Lens) 20

ASG129-125-800 ASG124-125-800 FilterSpecTM Black with FMP2 Valve Filter (Smoke Lens) 20

ASG149-125-800 ASG144-125-800 FilterSpecTM Black with FMP2 Odour Valve Filter (Smoke Lens) 20

ASG139-125-800 ASG134-125-800 FilterSpecTM Black with FMP3 Valve Filter (Smoke Lens) 20

RESPIRATORY PROTECTION - DISPOSABLE MASKS, TYPHOON™ TECHNOLOGY


BEY110-201-000 Typhoon Horizontal FoldFlat FFP1 - 315 Overfl ow Valved 10 x 10


BEY150-201-000 Typhoon Horizontal FoldFlat Odour FFP2 - 326 Overfl ow Valved 10 x 10


TyphoonTM Valve Fold Flat MasksHorizontal Foldable Shape for better fi tting and clear vision, hygienically

individually packed. Extremely low breathing resistance, extremely low CO2

and heat build up, and extremely low moisture build up.

Conforms to EN149:2001+A1:2009


HORIZONTAL FOLD FLAT MASKS WITH TYPHOON™ VALVE

360O COMFORT FOAM A foam area around the inside of the mask provides a perfect fi t and

maximum resistance as well as preventing misting.

WELDED NOSE PIECEThe welded nose piece prevents any irritation,

misshaping and a tighter fi t

LATEX FREE ADJUSTABLE STRAPThe adjustable strap means it can be fi tted comfortably

to all head sizes and shapes.

UNIQUE VALVEThe silicone valve is unaffected by any moisture,

and therefore can be used with the same

performance under very low temperatures.

1

2

3

4

THE UNIQUE TYPHOON™ VALVE SYSTEMWhen the Diaphragm opens, exhaled air that would

normally be trapped under the upper section of the cage

and obstruct further exhalation, can escape, through the

additional overfl ow vents, and assure unrivalled minimum

breathing resistance. The Diaphragm is made out of

Silicone in order not to be affected by any moisture, and

therefore can be used with the same performance under

very low temperatures.

315 - FFP1 VALVED

NEW12

34

4

RIGH

TS RESERVED

DESIGN REGISTERED

325 - FFP2 VALVED

326 - FFP2

ODOUR VALVED

335 - FFP3 VALVED

FLEXIBLE COVER Flexible cover to protect and retain the shape of the mask

during long periods of wear

FACE SEALImproved Face seal for added comfort

GRILLTo protect the wearer against possible damage to the fi lter.

Hand welded seal allows for extremely effi cient sealing.

MODERN VALVEModern design valve allows for lower

breathing resistance.

1

2

3

4


FLEXINET™ DISPOSABLE MASKS - RESPIRATORY PROTECTION

BEQ122-101-000 FFP2 - 821 -

Small/Medium10 x 10

BEQ122-201-000 FFP2 - 821 -

Medium/Large10 x 10

Flexinet™ FFP2 - 821Medium effi ciency (94%

minimum) dust mask. There is

no need for a valve for lower

breathing resistance.


FLEXINET™ DISPOSABLE MASK

BER152-101-000 FFP2 Odour Valved -

823 - Small/Medium 10 x 10

BER152-201-000 FFP2 Odour Valved -

823 - Medium/Large 10 x 10

Flexinet™ FFP2 Odour Valved - 823 Activated carbon layer is

incorporated to remove

nuisance odours.


BER122-101-000 FFP2 Valved - 822-

Small/Medium10 x 10

BER122-201-000 FFP2 Valved - 822-

Medium/Large10 x 10

Flexinet™ FFP2 Valved - 822Medium effi ciency (94% minimum)

with exhalation to increase

comfort.

BER130-001-000 FFP3 Valved - 832

- One Size Only10 x 5

Flexinet™ FFP3 Valved - 832High effi ciency (99%

minimum) fi ltering

with exhale valve

and fully adjustable

4-point harness.

FLEXINET™ DELUXE DISPOSABLE MASK

The FlexinetTM disposable mask has an ergonomic 3D design to fi t most face shapes, and has extremely low breathing resistance due

to the mask’s design and protective shield. Because it has no metal parts it is ideal for use within the medical & pharmaceutical industry.

Available in two sizes (small/medium & medium/large), perfect for fi t testing. Conforms to EN149:2001+A1:2009

1

2

3

4

4

RIGH

TS RESERVED

DESIGN REGISTERED

RESPIRATORY PROTECTION - DISPOSABLE MASKS


BEJ110-001-000 FFP1 - 111 10 x 20

BEK110-001-000 FFP1 - 112 Valved 10 x 20

BEK140-001-000 FFP1 - 113 Odour Valved Welding 10 x 20

FFP1 Moulded Disposable MasksThis “shaped to fi t” quality range of

moulded disposable masks are available in

Small, Medium and Large sizes. The valve

products increase user comfort by lowering

C02 and heat build up. Class 1 effi ciency

(80% minimum) for low risk hazards where

a protection factor up to 4 is required.



MOULDED DISPOSABLE MASKS

BEJ120-001-000 FFP2 - 121 10 x 20

BEK120-001-000 FFP2 - 122 Valved 10 x 20

BEK150-001-000 FFP2 - 123 Odour Valved Welding 10 x 20

FFP2 Moulded Disposable MasksClass 2, medium effi ciency

(94%) with a protection

factor of 10. Conforms to

EN149:2001+A1:2009

BEK130-001-000 FFP3 - Valved - 132 Medium 10 x 5

FFP3V Moulded Disposable MasksClass 3, high effi ciency (99%) with a protection factor of 20.


BEA110-101-000 FFP1 - 211 10 x 20

BEB110-101-000 FFP1 - Valved - 212 10 x 10

BEA120-101-000 FFP2 - 221 10 x 20

BEB120-101-000 FFP2 - Valved - 222 10 x 10

BEB150-101-000 FFP2 - Odour - Valved - 223 10 x 10

BEB130-101-000 FFP3 - Valved - 232 10 x 10

Disposable Vertical Fold Flat MasksHandy sized and easily pocketed these individually packed masks

hygienically fold fl at when not in use. Ergonomically shaped for an

effi cient fi t. Conforms to EN149:2001+A1:2009


FOLDFLAT DISPOSABLE MASKS

Hand SanitiserThe sanitiser is available

in 500ml pump disepnser

and a personal 50ml bottle,

supplied in counter top

display cartons.

ASE210-000-000 500ml Bottle 10

ASE201-000-000 Box of 42 x 50ml Bottle 1

FFP1

FFP1V

FFP1OV

FFP1 FFP1V

FFP2

FFP20V

FFP2V

FFP3V

FFP2

FFP2V

FFP20V

FFP3V


DISPOSABLE MASKS - RESPIRATORY PROTECTION

M05650 Maintenance Free (Disposable) A1P2 Maximask 2000 - Chapsmith 24


Compliance Disposable Half MaskTwin fi lter disposable Half Mask suitable for use in heavy manual work

conditions. It features a rigid cradle harness fi tted and A1P2 fi lters fi tted.

Conforms to EN140

Moulded DisposableDust Mask- EN149:2001+A1:2009

FP1 - 111 • • • • • FFP1 Valved - 112 • • • • • • FFP1 Odour Valved - 113 • • • • • FFP2 - 121 • • • • • • • • FFP2 Valved - 122 • • • • • • • • FFP2 Odour Valved - 123 • • • • • • • • • FFP3 Valved - 132 • • • • • • • • • • • • •Flexinet - EN149:2001+A1:2009

FFP2 - 821 • • • • • • • • FFP2 Valved - 822 • • • • • • • • FFP2 Odour Valved - 823 • • • • • • • • • FFP3 Valved -832 • • • • • • • • • • • • •Vertical Foldfl at - EN149:2001+A1:2009

FFP1-211 • • FFP1 Valved.-212 • • FFP2-221 • • • • • • • • FFP2 Valved-222 • • • • • • • • FFP2 Odour Valved-223 • • • • • • • • • FFP3 Valved-232 • • • • • • • • • • • • •

Br

ick

Dust

Co

ncre

te

Fe

rros

Met

al F

ume

Fi

bre

Glas

s

Le

ad F

ume

M

DF H

and

Tool

s

M

iner

al F

ibre

s

Pl

aste

r

Ro

ckw

ool

Sa

ndst

one

Si

lica

W

eldi

ng

W

ood

Soft

W

ood

Hard

DISPOSABLE MASK PRODUCT SELECTOR

HALFMASKS™

Please contact sales dept for full Chapsmith® range.

Date post:	19-Mar-2016
Category:	Documents
Upload:	spars-seguranca-e-higiene-no-trabalho
View:	247 times
Download:	8 times

JSP_PLIST_10_RESPIRATORY

Documents