Junction Boxes Enclosures

7/22/2019 Junction Boxes Enclosures

1/13

TERMINAL BOXES

ELECTRICAL ENCLOSURES

HAZARDOUS AREA ENCLOSURES

SPECIAL PURPOSE ENCLOSURES

ABTECH

ENCLOSURE SPECIALISTS FOR THE ELECTRONICS, INSTRUMENTATION,

MARINE, OIL, GAS AND PETRO-CHEMICAL INDUSTRIES


2/13

A B T E C H B P G R A N G E

The BPG range comprises 16 sizes of

enclosure manufactured in glass reinforced

polyester. The polyester is highly resistant to

contamination from oils, fats, aliphatic and

aromatic carbohydrates, bacteria and

enzymes. It is also suitable for LSOH (low

smoke zero halogen) applications. This

material gives excellent mechanical strength

and life expectancy. The wall thickness is

sufficient to allow tapped entry holes to be

machined in the walls of the enclosure and itprovides a very good alternative to

aluminium or cast iron.

Abtech mould the BPG range from SMC

material rather than DMC which is the most

common form of GRP. In this method the

glass reinforcement takes the form of sheets

rather than short strands. This gives much

greater mechanical strength and also in the

event of the enclosure being exposed to fire

conditions the structure holds together even

if the resin is depleted due to the elevated

temperatures as demonstrated by the fact

that the BPG range when fitted with ceramic

terminals meets the requirements of IEC 331

(750C for 3 hours) and also BS6387/1983

(950C for 3 hours - flame only).

Due to the enclosures labyrinth seal system,

whereby the seal is protected from external

forces, the BPG enclosure has excellent

ingress protection qualities which mean thatthe enclosure is tested to and passed

IP66/67 and has also undergone and

passed the Shell/ERA deluge test which was

devised to adequately test enclosures and

electrical equipment which is routinely

subjected to ships decks conditions or fire

deluge systems. The mounting holes,

although contained within the profile of the

enclosure, sit outside the seal and all

external fasteners and fixings are

manufactured from 316 grade stainless steel

to ensure reliability.

The BPG range has many features which

lend itself to a whole host of applications

including both industrial and hazardous

area, junction boxes, OEM applications, fire

protection systems, tunnel wiring etc. The

BPG range can be machined, drilled, tapped

with various thread forms, painted and of

course it can be moulded in a variety of

colours which gives a much improved

durability of colour over painting.

The BPG range is also available carbon

loaded (BPGC) which helps to reduce the

surface resistance of the material and

consequently reduce the risk of spark from

static build up.

Earthing can be acomplished by various

means. External/internal earth stud which inturn can be connected to the termina

mounting rail or component mounting plate,

an ECP (earth continuity plate) can be fitted

around the inner walls to provide continuity

for cable glands and various in rail mounted

earth terminals or proprietary earth bars can

be fitted inside the enclosure.

When fitted with a standard neoprene gasket

the enclosure is suitable for ambient

temperatures of -40C to 80C. Alternatively

when fitted with an optional silicone gasket

the temperature range is increased to -70C

to 130C. For certified apparatus contact

Sales Department for ambient operating

temperatures.

The BPG and BPGC enclosures are suitable

for use in hazardous areas and can be

supplied with a number of certificates,

specifically ATEX EEx e to BS EN 50019

(zone 1 & 2) EEx nA to BS EN50021 (zone

2) and NEMA 4X (CSA, UL & FM class 1, div

2). The BPG range can be supplied fitted

with any component approved terminal to

apparatus level or can be supplied empty as

component approved for the clients own

certification requirements.


3/13


ECPCopper earth continuity plate.(Must also be fitted with earth stud)

ESEarth Stud.(May be brass or stainless steel)

ALAllen head fixing screw.(Stainless steel grade 316)

TPTamper-proof screws.(Requires special tool for removal)

HExternal hinges.

MComponent mounting plate.(Tufnol - standard, steel - option)

FExternal mounting feet.(Stainless steel grade 316)

EInternal earthing bar.(Can be fitted with clamps)

TDIN standard mounting rail.(TS15, TS32 or TS35, please specify)

A C C E S S O R I E SThe following table is a list of the available accessories suitable for particular sizes of BPG enclosures. Care should be taken when ordering

accessories for use with enclosures intended for hazardous areas to ensure that compliance with certification is retained.

SIZE DIMENSIONSC Ex ECP ES AL TP H M F E SIL T RFI

BPG1 80 x 75 x 55 n n n n n n n n n

BPG2 110 x 75 x 55 n n n n n n n n n

BPG3 160 x 75 x 55 n n n n n n n n n

BPG4 190 x 75 x 55 n n n n n n n n n

BPG4.5 190 x 75 x 75 n n n n n n n n n

BPG5 230 x 75 x 50 n n n n n n n n n

BPG6 122 x 120 x 90 n n n n n n n n n n n n n










C - Carbon Loaded (gives surface tracking value of between 106and 109 ohms).

Ex - Ex certified (may be component or apparatus certified - please specify requirements).

RFI - Fitted with RFI gasket and internally coated with RFI sheilding (depending on gasket used, may reduce IP rating).

SIL - Silicone gasket giving greater temperature range (may also increase life when used in certain applications).


4/13

SCSPOWER

RATING(S)

NO.OFROWS

BK

4(4way

BK6(6way)

BK

12(12way)

MK6/4

MK6/6

SAK2.5

SAK4

SAK6N

SAK10

SAK16

SAK35

GS/4(4way)

GS/6(6way)

GS/12(12way)

K3

UK3

K5

UK5

K10

UK10

K16

UK16

UK35

WEIDMULLER PHOENIX

SIZE

WAGO

8.390

8.551

8.833

9.012

9.260

9.378

10.500

10.34811.933

13.793

18.338

15.474

15.474

20.867

20.867

30.384

30.384

31.350

31.350

31.350

SIZE

Solid mm2 4 4 4 6 6 4 6 10 16 16 501 4 4 4 4 4 4 4 10 10 16 16 35

Stranded mm2 4 6 10 16 16 35 4 6 10 16 35 4 4 4 2.5 2.5 4 4 6 6 10 10 35

CURRENT(A) 21 21 21 26 26 21 28 36 50 66 21 21 21 21 21 21 21 37 37 47 47 75

TERMINAL TYPE

BOX TYPE

BPG 1 1 1 1 - 1 - - - - - - - 1 1 - - - - - - - - - -

BPG 2 1 2 1 - 1 1 - - - - - - 2 1 - - - - - - - - - -

BPG 3 1 3 - 1 2 1 - - - - - - 3 2 1 - - - - - - - - -

BPG 4 1 4 - 1 3 2 - - - - - - 4 3 1 - - - - - - - - -

BPG 5 1 5 3 2 4 2 - - - - - - 5 3 2 - - - - - - - - -

BPG 6 1 - - - - - 10 9 7 6 5 3 - - - 12 12 10 10 6 6 6 6 4

BPG 7 1 - - - - - 26 24 20 16 13 10 - - - 30 30 25 25 19 19 15 15 10

BPG 8 1 - - - - - 16 15 12 9 8 5 - - - 19 19 16 16 12 12 9 9 5BPG 9 1 - - - - - 33 30 25 20 16 12 - - - 38 38 32 32 24 24 19 19 13

BPG 10 1 - - - - - 48 45 36 29 24 18 - - - 56 56 48 48 36 36 29 29 18

BPG 11 1 - - - - - 80 74 61 48 41 30 - - - 94 94 78 78 58 58 46 46 32

BPG 12 1 - - - - - 31 29 24 19 16 12 - - - 37 37 31 31 23 23 18 18 12

BPG 12 2 - - - - - 62 58 48 38 - - - - - 74 74 62 62 46 46 36 36 -

BPG 13 1 - - - - - 55 50 41 33 27 20 - - - 64 64 53 53 40 40 32 32 22

BPG 13 2 - - - - - 110 100 82 66 - - - - - 128 128 106 106 80 80 64 64 -

BPG 14 1 - - - - - 87 81 66 52 41 32 - - - 103 103 86 86 64 64 51 51 34

BPG 14 2 - - - - - 174 162 132 104 82 64 - - - 206 206 172 172 128 128 102 102 -

BPG 15 1 - - - - - 55 50 41 33 27 20 - - - 64 64 53 53 40 40 32 32 22

BPG 15 2 - - - - - 110 100 82 66 54 - - - - 128 128 106 106 80 80 64 64 -

BPG 15 3 - - - - - 110 100 82 66 81 - - - - 192 192 159 159 120 120 - - -

The above power ratings apply to an ambient operating temperature of 40C. Reduced power ratings are available for ambient temperatures up to +65C.


Stranded mm2 2.5 2.5 4 4 4 6 10 16 35 2.5 4 2.5 2.5 2.5 2.5 2.5 2.5

CURRENT(A) 23 20 30 30 30 39 53 72 120 23 30 23 23 23 23 23 23

TERMINAL TYPE

BOX TYPE

BPG 1 8.390 1 - - - - - - - - - - - 6 3 6 3 6 3

BPG 2 8.551 1 - - - - - - - - - - - 10 5 10 5 10 5

BPG 3 8.833 1 - - - - - - - - - - - 18 9 18 9 18 9

BPG 4 9.012 1 - - - - - - - - - - - 24 12 24 12 24 12

BPG 5 9.260 1 - - - - - - - - - - - 30 15 30 15 30 15

BPG 6 9.378 1 14 14 12 12 12 9 7 6 - 14 12 12 6 12 6 12 6

BPG 7 10.500 1 32 32 27 27 27 21 17 14 - 32 27 27 13 27 13 27 13

BPG 8 10.348 1 19 19 16 16 16 13 10 8 - 19 16 16 8 16 8 16 8

BPG 9 11.933 1 38 38 33 33 33 25 20 17 - 38 33 33 16 33 16 33 16

BPG 10 13.793 1 56 56 49 49 49 38 30 25 - 56 49 49 24 49 24 49 24

BPG 11 18.338 1 94 94 81 81 81 62 50 42 - 94 81 81 40 81 40 81 40

BPG 12 15.474 1 36 36 32 32 32 25 20 16 11 36 32 32 16 32 16 32 16

BPG 12 15.474 2 72 72 64 64 64 50 40 32 - 72 64 64 32 64 32 64 32

BPG 13 20.867 1 65 65 55 55 55 42 34 28 19 65 55 55 27 55 27 55 27

BPG 13 20.867 2 130 130 110 110 110 84 68 56 - 130 110 1 10 55 110 55 110 55

BPG 14 30.384 1 102 102 88 88 88 67 54 45 31 102 88 88 44 88 44 88 44

BPG 14 30.384 2 104 104 176 176 176 134 108 90 - 104 176 176 88 176 88 176 88

BPG 15 31.350 1 130 130 55 55 55 42 34 28 19 130 55 55 27 55 27 55 27

BPG 15 31.350 2 260 260 110 110 110 84 68 56 - 260 110 1 10 55 110 55 110 55

BPG 15 31.350 3 390 390 165 165 165 126 102 84 - 390 165 165 81 165 81 165 81

SCS

POWER

ratings

(W)

NO.

OFROWS

280

-

991

280

-

699

281

-

691

281-

991

281

-

695

282

-

691

284

-

691

283

-

691

285

-

691

280

-

698

281

-

693

264

-

120

264

-

220

2642Cond.

Strip

2644Cond.

Strip

2622Cond.

Strip

2624Cond.

Strip


In some instances the terminal content shown above exceeds the power rating if all terminals are used at full certified current rating. In this instance steps

should be taken to ensure the power rating is not exceeded.

The ABTECH BPG Ex range, when fitted with any component certified EExe terminals, is Sira ATEX certified to EN 50 014 and EN 50 019. The empty enclosure

is component certified and available for adding clients components subject to final approval by Sira or any recognised certifying authority. ABTECH have many

years experience in the application of enclosures in hazardous areas and will be pleased to offer advice for any enclosure problems.

The power rating refers to the permitted power losses inside the enclosure. It is the responsibility of the user to keep power losses within these limits. Annex C2

T E R M I N A L C O N T E N T SThe following tables are provided as a guide only. Due to space limitations only Weidmuller, Wago and Phoenix terminal populations are shown. Any

component certified terminal may be fitted to the BPG range provided compliance with the terminal manufacturers component certificate is adhered to.


5/13


ab123

Glass reinforced polyester enclosures offering protection to IP 67.Temp range -40C to 80C with standard gasket or -70C to 130Cwith silicone gasket. Standard finish as moulded isRAL 7001 grey or black for BPGC.Can be moulded in variety of colours.

BPG 2/BPGC 2Size: 110 x 75 x 55mmWeight: 230gRating: 8.551Watts



BPG 4/BPGC 4Size: 190 x 75 x 55mmWeight: 450g

Rating: 9.012Watts


6/13


ab123






Rating: 10.348Watts

76

110


7/13


ab123






Rating: 15.474Watts


8/13


ab123






9/13

A B T E C H B P G A R A N G E

The Abtech BPGA range comprises three types of

BPG enclosures in two different sizes which are

available pre-assembled and readily available off the

shelf. They are ideal for a range of uses such as

lighting, power and instrument junction boxes.

They are manufactured in impact resistant glass

reinforced polyester which has an ingress protection

rating of IP66/67 and are Shell/ERA deluge tested.

The enclosures come equipped with terminals as shown

in the table below, copper earth continuity plate and

brass M6 internal/external earth stud. The enclosure is

pre-drilled with four M20 tapped cable entries and is

supplied complete with EEx e certified blanking plugs.

The range is ATEX certified EEx e and is suitable for

use in Category 2/Zone 1 and Category 3/Zone 2 areas

according to EN 60079-14 with a working ambient

temperature of between -20C and +40C.

SPECIFICATION BPGA 120 BPGA 125 BPGA 160

Size (external) 122 x 120 x 90 122 x 120 x 90 160 x 160 x 90

Entries 4 x M20 (2 x A, 2 x C) 4 x M20 (2 x A, 2 x C) 4 x M20 (2 x A, 2 x C)

EEx e Blanking plugs 3 3 3

Terminals 6 x SAK 2.5 1 x MK6/6 way 13 x SAK 2.5

Links Linked in pairs Linked in pairs na

Int/Ext M6 earth stud Yes Yes Yes

Copper earth continuity plate Yes Yes Yes

Ingress Protection (IP) IP 66/67 IP 66/67 IP 66/67

Shell/ERA Deluge tested Yes Yes Yes


10/13

A B T E C H S X R A N G E

The SX range comprises 14 sizes of

enclosure manufactured in either mild steel

or stainless steel. Depending on the

enclosure size they are available in standard

depths of 140, 200 or 300mm and can be

fitted with removable gland plates on any or

all of the four sides. The mild steel version

(MSX) is available with a number of paint

options (most RAL colours available) and

anti corrosion finishes and advice on this can

be sought from Abtech.

The stainless steel range (SSX) is

manufactured in 316 grade stainless steel to

give the maximum environmental protection.

The main body is manufactured from 2mm

thick sheet and the mounting straps and

gland plates from 3mm thick plate.

Cable entries can be drilled in the sides or

through the gland plates, if fitted, or through

the enclosure wall. Entries may also be

drilled through the rear face of the enclosure

(EEx versions also.)

The SX range was specifically designed to

meet the rigours of the North Sea

environment and is capable of achieving

IP66 and IP67 and has also undergone andpassed the Shell/ERA deluge test which was

devised to adequately test enclosures and

electrical equipment which is routinely

subjected to ships decks conditions or fire

deluge sytems.

IP68 enclosures are aslo available for depths

up to 120 ft to special order.

Another advantage of the SX range is that it

is suitable for fire resistance applications

and when fitted with ceramic terminals

meets the requirements of IEC 331 (750C

for 3 hours) and also BS6387/1983 (950C

for 3 hours).

Another important feature of the SX range is

the door, which is held to the enclosure by at

least 4 captive stainless steel screws, which

also maintain the correct compression onthe gasket. The hinges are solid block,

machined oversize to enable the screws to

control the closing of the door, not the hinge,

its only function being to support the door

when opened. The hinges allow easy

removal of the door with only minimal

opening required before removal (less than

10).

The SX range has many features which lend

itself to many applications, not least of which

is the ability to be constructed to almost any

dimension due to its fabricated nature. This

can also be applied to EEx enclosures

where the certification allows oversize

enclosures to be manufactured whilst

retaining the next smallest sized enclosures

power rating. Other applications include

junction boxes, both industr ial and

hazardous area, OEM applications, fire

protection systems, tunnel wiring, IP68

applications, etc.

Earthing is accomplished by means of an

external/internal earth stud fitted as standard

which can be connected to the termina

mounting rail or component mounting plate

and optionally earth studs can be fitted tothe door and gland plates. Rail mounted

earth terminals or proprietary earth bars can

be fitted inside the enclosure and Abtech

sales staff will be happy to advise on this.

When fitted with a standard neoprene

gasket, the enclosure is suitable for ambient

temperatures of -40Cto 80C. Alternatively

when fitted with an optional silicone gasket

the temperature range is increased to -70C

to 130C.

The SX range of enclosures are suitable for

use in hazardous areas and can be supplied

with a number of certificates. ATEX EEx e to

BS EN 50019 (Zone 1 & 2) EEx nA to BS

EN50021 (Zone 2) and NEMA 4X (CSA, UL &

FM class 1, div 2). The SX range can be

supplied fitted with any component

approved terminal to apparatus level or can

be supplied empty as component approved

for the clients own certification requirements.


11/13


GPGland plates.(Please specify sides to be fitted)

ESEarth Stud fitted to door and gland

plates. (If fitted - specify size req.)

ELElectro-polished.(External surface 316 SS only)

LBLabel bracked.

(Welded to door - specify size)

MComponent mounting plate.(Steel or stainless steel)

EInternal earthing bar.

(Can be fitted with clamps)

A C C E S S O R I E SThe following table is a list of the available accessories suitable for particular standard sizes of SX enclosures. Care should be taken when ordering

accessories for use with enclosures intended for hazardous areas to ensure that compliance with certification is retained.

Size Dimensions GP 140 200 300 EL LB ES E SIL BD TP M RFI

SX45 114 x 114 x 51 n n n n n n n

SX64 102 x 152 x 63 n n n n n n n

SX66 152 x 152 x 102 n n n n n n n n n n

SX0 152 x 229 n n n n n n n n n n n n

SX0.5 184 x 274 n n n n n n n n n n n n


SX1.5 306 x 306 n n n n n n n n n n n n





SX6 510 x 780 n n n n n n n n n n n n n



All SX range enclosures are available manufactured in either mild steel - MSX or stainless steel grade 316 - SSX

All SX range enclosures are available Ex certified (component or apparatus certified - please specify requirements)

All SX range enclosures meet IP66/67. When fitted with gland plates the standard IP rating is IP66. IP67 available as option.

RFI - Fitted with RFI gasket (depending on gasket used, may reduce IP rating)

SIL - Silicone gasket giving greater temperature range. (may also increase life when used in certain applications)

EL - Electropolished external enclosure surface (stainless steel 316 only)

BD - Breather drain (IP66 stainless steel or plastic)

TP - Tamper-proof lid fixing screws

DEPTH


12/13

SCSPOWER

RATING(S)

NO.OFROWS

SAK2.5

SAK6

SAK6

SAK10

SAK16

SAK35

SAK70

UK2.5B

UK3

UK5

UK10

UK16

UK35

KLIPPON PHOENIX

SIZE

WAGO

T E R M I N A L C O N T E N T SThe following table is provided as a guide and due to space limitations in this brochure only Klippon, Wago and Phoenix terminal

populations are shown. All Abtech enclosures are available empty or alternatively may be provided with terminals, entries, accessories and

other electromechanical components.

Solid mm2 4 6 10 16 16 35 70 2.5 4 4 10 16 35

Stranded mm2 4 4 6 10 16 35 70 2.5 2.5 4 6 10 35

ATEX CURRENT(A) 15 22 26 37 47 75 - - - - - - -

TERMINAL TYPE

BOX TYPE

SX 45 1 6 - - - - - - 6 9 - - - -

SX 64 10.258 1 14 12 10 8 - - - 14 16 10 8 - -

SX 66 14.287 2 14 12 10 8 7 4 - 14 16 10 8 7 4

SX 0 19.874 1 17 15 13 10 8 6 3 17 20 13 10 8 6

SX 1 29.206 1 25 25 21 17 14 9 9 25 34 21 17 14 9

SX 1.5 32.284 2 48 48 40 32 13 8 9 48 68 40 32 13 8

SX 2 36.500 2 50 50 42 34 14 9 9 50 68 42 34 14 9

SX 3 42.289 2 90 90 76 60 25 16 12 90 118 76 60 25 16

SX 4 44.726 2 110 110 90 72 30 20 16 110 140 90 72 30 20

SX 5 50.238 3 165 165 135 108 60 40 32 165 210 135 108 60 40

SX 6 57.383 3 300 300 234 189 104 70 58 300 366 234 189 104 70

SX 7 68.000 3 408 408 300 240 198 132 100 408 465 300 240 198 132

4 544 544 400 320 - - - 544 620 400 320 - -

SX 8 119.463 5 915 845 685 550 455 244 230 915 1060 686 550 455 244

6 1098 1014 822 660 - - - 1908 1272 822 660 - -



BOX TYPE

SX 45 8.950 1 6 - 5 5 - - - - - 6 5 6 3 6 6 5 4 6 3 6 3

SX 64 10.258 1 12 - 10 10 - - - - - 12 10 12 6 12 12 10 7 12 7 12 6

SX 66 14.287 1 12 12 10 10 10 9 7 6 - 12 10 12 6 12 12 10 7 12 7 12 6

SX 0 19.874 1 21 21 18 18 18 14 11 - - 21 18 10 12 19 14 11 9* 20 12 20 9

SX 1 29.206 1 35 35 29 29 29 23 18 15 10 35 29 32 19 30 23 18 18 32 19 32 15

SX 1.5 32.284 2 70 70 58 58 58 46 36 30 10 70 58 64 38 60 46 36 36 64 38 64 30

SX 2 36.500 2 70 70 58 58 58 46 36 30 10 70 58 64 38 60 56 36 36 64 38 64 30

SX 3 42.289 2 118 118 100 100 100 78 62 52 18 118 100 106 64 104 78 62 62 106 64 106 52

SX 4 44.726 2 140 140 120 120 120 92 74 62 21 140 120 126 76 124 92 74 74 126 76 126 62

SX 5 50.238 3 210 210 180 180 180 138 111 93 42 210 180 189 114 186 138 111 111 189 114 189 93

SX 6 57.383 3 360 360 300 300 300 130 189 156 74 360 300 15 192 318 240 189 189 315 192 314 156

SX 7 68.000 3 450 450 390 390 390 300 240 195 135 450 390 405 240 390 300 240 240 405 240 405 195

4 600 600 520 520 520 400 320 260 - 600 520 540 320 520 400 320 320 540 320 540 260

SX 8 119.463 5 1000 1000 875 875 875 675 550 450 252 1000 875 925 550 920 675 550 550 925 550 925 450

6 1200 1 200 1 050 1 050 1 050 810 660 540 - 1200 1 050 1 110 610 1104 810 660 660 1110 650 1110 540

In some instances the terminal content shown above exceeds the power rating if all terminals are used at full certified current rating. In this instance steps should be taken to ensure the

power rating is not exceeded.

The ABTECH SX Ex range, when fitted with any EExe component approved terminals(1) is Sira certified to EN 50 014 and EN 50 019. The empty enclosure is component certified and

available for adding clients components subject to final approval by Sira or any suitable notified body. ABTECH have many years experience in the application of enclosures in hazardous

areas and will be pleased to offer advice for any enclosure problems.

(1) Any apparatus certified enclosure built after June 2003 must be fitted with ATEX approved terminals or components. Abtech sales staff can provide help and information on anyaspect of

certification in relation to Abtech enclosures.

The power rating refers to the permitted power losses inside the enclosure. It is the responsibility of the user to keep power losses within these limits. Annex C2 of BS EN 50019 details the

appropriate calculation method.

SCS

POWE

R

ratings

(W

)

NO.

OFROW

S

280

-

991

280

-

699

281

-

691

281-

991

281

-

695

282

-

691

284

-

691

283

-

691

285

-

691

280

-

698

281

-

693

264

-

120

264

-

220

281

-

191

282

-

191

284

-

191

283

-

191

2642Cond.

Strip

2644Cond.

Strip

2622Cond.

Strip

2624Cond.

Strip


13/13


abMild steel or stainless steel enclosures offering protection toIP 67. Temp range -40C to 80C with standard gasket or -70Cto 130C with silicone gasket.

MSX/SSX 64Size: 102 x 152 x 102mmWeight: 1.5kgRating: 10.258Watts



MSX/SSX 0Size: 229 x 152 x 140/200mmWeight: 3.2kg (140)

4.0kg (200)Rating: 19.874Watts

Date post:	10-Feb-2018
Category:	Documents
Upload:	john-arllan-diestro
View:	224 times
Download:	0 times

Junction Boxes Enclosures

Documents