(02~06, A-8) by (02~06 & 01)(07~13) by (07~13)(A~1) by (14~22)(J~W) by (23~36)(W+1~W+28) by (37~64)(W+29~W+84) by (65~125)(A8, A4~A1) by (01, 96~99)
TV/CATV Total Channel 180 ChannelsAntenna Terminal (VHF/UHF) 75ohm unbalanced F-type connector Intermediate Frequency
Video IF CarrierSound IF Carrier
45.75MHz41.25MHz (4.5MHz)
Color Sub Carrier 3.58MHzPower InputPower Consumption
120V AC, 60Hz248W (Max)
ScreenScreen SizeProjection TubeHigh Voltage
Transparent screen (unitized fresnel lens/double lenticular lens)65" (165cm) Measured diagonally, 16:9 ratio (W:143.9 cm, H:81.0 cm)17cm (6.7") tube x 3 ( R/G/B )31kV±1.0kV (at zero beam current)
SpeakerAudio Power Output
16cm round x 2 (Woofer), 5.5cm round x 2 (Tweeter)10W+10W
External InputVideo InputAudio Input
S-Video
Component Input
1V (p-p), 75ohm (RCA pin jack x 4)500mV(rms) ( -4dBs), high impedance (RCA pin jack x 8)Y: 1V (p-p) positive, 75ohm negative sync providedC: 0.286V(p-p) (burst signal)Mini-DIN 4pin connector x 2Y: 1V (p-p), 75ohm (RCA pin jack x 2)Pb: ±0.35V(p-p), 75ohm (RCA pin jack x 2)Pr: ±0.35V(p-p), 75ohm (RCA pin jack x 2)1080i DTV (digital broadcast) ready
Digital Input
Audio Input
DVI-D signal link 19pin connector(Digital-input terminal is not compatible with computer signal)500mV(rms) ( -4dBs), high impedance (RCA pin jack x 2)
Subwoofer Output More than 0 to 1000mV (rms) (+2.2dBs) (RCA pin jack x1)Audio Output (VARI/FIX) VARI : More than 0 to 1000mV (rms) (+2.2dBs)
FIX : 500mV(rms) (-4dBs), low impedance (1kHz when modulated 100%)(RCA pin jack x 2)
Speaker Input 45W 16ohm (maximum input)AV Compulink lll Ø3.5mm mini jackRemote Control Unit RM-C1200G (AA/R6/UM-3 battery x 2)
AV-65WP74
(No.52096)1-3
SECTION 1PRECAUTIONS
1.1 SAFETY PRECAUTIONS(1) The design of this product contains special hardware, many circuits
and components specially for safety purposes. For continuedprotection, no changes should be made to the original design unlessauthorized in writing by the manufacturer. Replacement parts mustbe identical to those used in the original circuits. Service should beperformed by qualified personnel only.
(2) Alterations of the design or circuitry of the products should not bemade. Any design alterations or additions will void the manufacturer'swarranty and will further relieve the manufacturer of responsibility forpersonal injury or property damage resulting therefrom.
(3) Many electrical and mechanical parts in the products have specialsafety-related characteristics. These characteristics are often notevident from visual inspection nor can the protection afforded by themnecessarily be obtained by using replacement components rated forhigher voltage, wattage, etc. Replacement parts that have thesespecial safety characteristics are identified in the parts list of Servicemanual. Electrical components having such features areidentified by shading on the schematics and by ( ) on the partslist in Service manual. The use of a substitute replacement whichdoes not have the same safety characteristics as the recommendedreplacement part shown in the parts list of Service manual may causeshock, fire, or other hazards.
(4) Use isolation transformer when hot chassis.The chassis and any sub-chassis contained in some products areconnected to one side of the AC power line. An isolation transformerof adequate capacity should be inserted between the product and theAC power supply point while performing any service on someproducts when the HOT chassis is exposed.
(5) Don't short between the LIVE side ground and ISOLATED(NEUTRAL) side ground or EARTH side ground when repairing.Some model's power circuit is partly different in the GND. Thedifference of the GND is shown by the LIVE : ( ) side GND, theISOLATED(NEUTRAL) : ( ) side GND and EARTH : ( ) side GND.Don't short between the LIVE side GND and ISOLATED(NEUTRAL)side GND or EARTH side GND and never measure with a measuringapparatus (oscilloscope etc.) the LIVE side GND andISOLATED(NEUTRAL) side GND or EARTH side GND at the sametime.If above note will not be kept, a fuse or any parts will be broken.
(6) The high voltage applied to the picture tube must conform with thatspecified in Service manual. Excessive high voltage can cause anincrease in X-Ray emission, arcing and possible component damage,therefore operation under excessive high voltage conditions shouldbe kept to a minimum, or should be prevented. If severe arcingoccurs, remove the AC power immediately and determine the causeby visual inspection (incorrect installation, cracked or melted highvoltage harness, poor soldering, etc.). To maintain the properminimum level of soft X-Ray emission, components in the highvoltage circuitry including the picture tube must be the exactreplacements or alternatives approved by the manufacturer of thecomplete product.
(7) If any repair has been made to the chassis, it is recommended thatthe B1 setting should be checked or adjusted (See ADJUSTMENTOF B1 POWER SUPPLY).
(8) Do not check high voltage by drawing an arc. Use a high voltagemeter or a high voltage probe with a VTVM. Discharge the picturetube before attempting meter connection, by connecting a clip lead tothe ground frame and connecting the other end of the lead through a10kΩ 2W resistor to the anode button.
(9) When service is required, observe the original lead dress. Extraprecaution should be given to assure correct lead dress in the highvoltage circuit area. Where a short circuit has occurred, thosecomponents that indicate evidence of overheating should bereplaced. Always use the manufacturer's replacement components.
(10) Isolation Check(Safety for Electrical Shock Hazard)After re-assembling theproduct, always perform an isolation check on the exposed metalparts of the cabinet (antenna terminals, video/audio input and outputterminals, Control knobs, metal cabinet, screwheads, earphone jack,control shafts, etc.) to be sure the product is safe to operate withoutdanger of electrical shock.
a) Dielectric Strength TestThe isolation between the AC primary circuit and all metalparts exposed to the user, particularly any exposed metal parthaving a return path to the chassis should withstand a voltageof 1100V AC (r.m.s.) for a period of one second.(. . . . Withstand a voltage of 1100V AC (r.m.s.) to an appliancerated up to 120V, and 3000V AC (r.m.s.) to an appliance rated200V or more, for a period of one second.)This method of test requires test equipment not generallyfound in the service trade.
b) Leakage Current CheckPlug the AC line cord directly into the AC outlet (do not use aline isolation transformer during this check.). Using a "LeakageCurrent Tester", measure the leakage current from eachexposed metal part of the cabinet, particularly any exposedmetal part having a return path to the chassis, to a known goodearth ground (water pipe, etc.). Any leakage current must notexceed 0.5mA AC (r.m.s.). However, in tropical area, this mustnot exceed 0.2mA AC (r.m.s).• Alternate Check Method
Plug the AC line cord directly into the AC outlet (do not usea line isolation transformer during this check.). Use an ACvoltmeter having 1000 ohms per volt or more sensitivity inthe following manner. Connect a 1500ohm 10W resistorparalleled by a 0.15µF AC-type capacitor between anexposed metal part and a known good earth ground (waterpipe, etc.). Measure the AC voltage across the resistor withthe AC voltmeter. Move the resistor connection to eachexposed metal part, particularly any exposed metal parthaving a return path to the chassis, and measure the ACvoltage across the resistor. Now, reverse the plug in the ACoutlet and repeat each measurement. Any voltagemeasured must not exceed 0.75V AC (r.m.s.). Thiscorresponds to 0.5mA AC (r.m.s.).However, in tropical area, this must not exceed 0.3V AC(r.m.s.). This corresponds to 0.2mA AC (r.m.s.).
(11) High voltage hold down circuit check.After repair of the high voltage hold down circuit, this circuit shall bechecked to operate correctly.See item "How to check the high voltage hold down circuit".
AC VOLTMETER(HAVING 1000 /V,OR MORE SENSITIVITY)
PLACE THIS PROBEON EACH EXPOSEDMETAL PART1500 10W
0.15 F AC-TYPE
GOOD EARTH GROUND
PWB
White line side
WHT
PW
POWER CORD REPLACEMENT WARNING.Connecting the white line side of power
cord to "WHT" character side.
A V
This mark shows a fast operating fuse, the letters indicated belowshow the rating.
AV-65WP74
1-4 (No.52096)
1.2 INSTALLATION1.2.1 REMOVING THE UPPER UNIT FROM THE LOWER UNIT1.2.1.1 TYPES AND PLACES OF SCREWS• Be careful not to confuse the following four types of screws.
Type
B
AA
A
CD
Ref. Place for attaching screws Quantity Color Shape4
diameter of 4mm-length of 18mm, acute tip
diameter of 3mm-length of 12mm, flat tipdiameter of 4mm-length of 12mm, flat tipdiameter of 4mm-length of 20mm, flat tip
22224
Black
BlackGoldBlackRear cover (for attaching the speaker panel)
FRONT SIDE
REAR SIDE
A : diameter of 4mm - length of 18mm, black, acute tip
A : diameter of 4mm - length of 18mm, black, acute tip
C : diameter of 4mm - length of 12mm, gold, flat tip
D : diameter of 4mm - length of 20mm, black, flat tip
B : diameter of 3mm - length of 12mm, black, flat tip
Rear cover (for attaching the body bracket)Inside the Front door (in the jack part)Rear cover (for attaching the body)Rear cover bracketFront panel bracket
1
A : diameter of 4mm - length of 18mm, black, acute tip1
3
A : diameter of 4mm - length of 18mm, black, acute tip6
2
4
5
D : diameter of 4mm - length of 20mm, black, flat tip5
AV-65WP74
(No.52096)1-5
1.2.1.2 DISASSEMBLY PROCEDURE• Make sure that the power cord is pulled out from the AC wall
socket.(1) Remove the 2 screws [ A ] on the left rear side of the set,
and then remove the rear cover bracket. [Fig.1](2) Remove the 2 screws [ B ] inside of the front door. [Fig.2]
* The screws attach the speaker panel.(3) Remove the 2 screws [ D ] on the left edge of the rear
cover, and remove the 2 screws [ D ] on the right edge ofthe rear cover. [Fig.2]* The screws attach the speaker panel.
(4) Pull the speaker grill in front direction, and remove thespeaker grill. [Fig.2]
(5) Remove the connector [CN00Z] for the auto-convergencesensor on the left side of the set, and the clamp fixing thewire. [Fig.2]
(6) Remove the 2 screws [ A ] on the left front panel bracket,and remove the 2 screws [ A ] on the right front panelbracket. [Fig.2]
(7) Remove 1 screw C on the left edge of the rear cover, and1 screw C on the right edge of the rear cover. [Fig.3]
(8) Remove 1 screw [ A ] on the left side of the rear cover, andremove 1 screw [ A ] on the right side of the rear cover.[Fig.3]
(9) Move the rear cover approx. 3cm in rear direction. Then,remove the upper unit from the lower unit by lifting theupper unit slowly. [Fig.3]• VOID seal [ a ] attached to the left front panel bracket in
order to confirm that a person except JVC installationworkers has disassembled the set. This seal is removedwhen the upper unit is removed, and the letters of "VOID"appears in the place where the seal. [Fig.2]
• Two or more people are required to move the upper unit.• Reflecting mirror is attached to the upper unit. So, handle
it carefully so as to protect it from shocks.• In placing the upper unit on the ground, be careful not to
insert the connector for the auto-convergence on theright side of the upper unit between the upper unit andthe ground.
• In placing the upper unit on the ground, be careful not toinsert dust inside the upper unit.
• Be careful not to hurt yourself because metal brackets forattaching the front panel are on the ceiling part of thelower unit.
(10) Cover the lower unit with the Top Sheet in order not toinsert dust in the lower unit. Top Sheet is the one used forpackage. [Fig.4]
Fig.1
Fig.2
Fig.3
Fig.4
A REAR COVERBRACKET
A
D
D
B
a
SPEAKER GRILL
CN00Z
C
A
UPPERUNIT
LOWERUNIT
TOP SHEET
AV-65WP74
1-6 (No.52096)
1.2.1.3 REASSEMBLY PROCEDURE• Make sure that power cord is pulled out from the AC wall
socket.• Remove the Top Sheet which covers the lower unit.
(1) Lift the upper unit slowly, and then place the upper unit onthe lower unit.• In placing the upper unit on the lower unit, be careful not
to insert the connector for the auto-convergence on theright side of the upper unit between the upper unit andthe lower unit.
(2) Adjust the front side of the upper unit to the brackets on thelower unit for attaching the upper unit.
(3) Attach 2 screws [ A ] to the both side of the rear cover.[Fig.2]
(4) Attach 2 screws [ A ] to the both edge of the rear cover.[Fig.2]
(5) Attach the 4 screws [ A ] to the front panel bracket. [Fig.2](6) Attach the VOID seal [ b ] on the front right side of the set
to the right front panel bracket. [Fig.5](7) Attach the speaker grill to the front side.(8) Attach 4 screws [ D ] to the both edge of the rear cover.
[Fig.2](9) Attach the 2 screws [ B ] to the front door. [Fig.2]
(10) Attach the connector for the auto-convergence sensor.• Make sure that all the screws are attached certainly in
order to fix the upper unit.• After assembly procedure is completed, make sure that
there is no dust in the inner side of the screen.
Fig.5
b
AV-65WP74
(No.52096)1-7
1.2.2 INSTALLATION SITE(1) The rear of this set is provided with ventilation openings.
Install the set more than 5 cm from a wall and in a locationwith good ventilation.
(2) Avoid the following types of locations.a) Unstable locations (location must be able to
withstand heavy weight).b) Locations subjected to direct sunlight.c) Near stoves or other heating devices.d) Locations subjected to humidity or oily smoke.e) Dusty locations.f) Locations with strong vibration.
1.2.3 INSTALLATION ADJUSTMENTWhen installing, moving or changing the orientation of the set,perform static convergence adjustment according to thefollowing procedure.Adjusting CRT color convergence have two method, AUTO,MANUAL and RESET. It adjust on the MENU screen.NOTE :
Please have you TV on for at least 20 minutes before sing thisfeature.This adjustment will be needed only when the colors of thecharacters/lines are separated and lack in distinction. If not,please don't perform the adjustment.
AUTO(1) Press the [MENU] key, and select the
"CONVERGENCE" in the INITIAL SETUP menu with[function up/down] key.
(2) Press the [function left/right] key, then CONVERGENCEmenu appear.
(3) Press the [function up/down] key, and select the"AUTO".
(4) Press the [function left/right] key.(5) he convergence adjustment will start. It will take about 50
seconds.MANUAL
(1) Press the [MENU] key, and select the"CONVERGENCE" in the INITIAL SETUP menu with[function up/down] key.
(2) Press the [function left/right] key, the CONVERGENCEmenu appears.
(3) Press the [function up/down] key, and select the"MANUAL".
(4) Press the [function left/right] key, then CONVERGENCEadjustment screen appear. [Fig.1]• If all the crosses are white, no convergence
adjustment is needed.(5) Select the location you want to adjust by using the
[number (2/4/5/6/8)] keys on the remote control unit.[Fig.2]
(6) Press the [SELECT] key to change the color of the boxto the color of the cross you want to adjust (red or blue).• You cannot adjust the green cross.
(7) Use the [function up/down] key and the [function left/right] keys to adjust the position of the cross.
(8) Adjust the three colors crosses until they overlap andappear as a single white cross.
(9) Press the [OK] key.
NOTE :• When you adjust the convergence, make sure you
start with the center position (position 5), and workyour way around radial for best results
• When you make the adjustment in the center(positions 5), you are making the adjustment for thewhale screen. In other positions, you are making theadjustment only in that area.
• You can reset the adjustment if you do not like theresults, See below.
• If you perform AUTO CONVERGENCE afterperforming MANUAL CONVERGENCE, yourmanual convergence you performed will becancelled.
(10) Press the [menu] key to end the convergenceadjustment procedure.
RESETRESET in the CONVERGENCE menu resets all convergenceadjustments to the factory default setting.
Fig.1
Fig.2
(more than 5cm)
Wall
VENTILATION OPENING
5
2
4 6
8
AV-65WP74
1-8 (No.52096)
SECTION 2SPECIFIC SERVICE INSTRUCTIONS
2.1 FEATURES• New chassis design enable use of an interactive on screen control.• 2-3 PULL DOWN : You can enjoy DVD movies at the highest picture quality.• MOTION COMPENSATION : With this function, the seamless reproduction of dynamic motion on the screen has been realized.• Bullet-in DSD (Digital Supper Detail) circuit and 3 dimension Y/C separate circuit.• Receive DTV broadcast (1080i / 720p / 480p / 480i)• Built-in HDCP / Component (Y / Pb / Pr) input.• Built-in Hyper Sound, BBE circuit.
2.2 FUNCTIONS
S-VIDEOS-VIDEOVIDEOVIDEO
OPERATEOPERATE
L / MONO / MONO R
INPUT4
SUPERSUPERFOCUSFOCUS
AUDIO OUTSUBWOOFEROUT
DIGITAL IN
INPUT-3
INPUT-2
INPUT-1
R LAUDIO VIDEO S-VIDEO
R L
AUDIO
R L
OVER
OVER
INPUT-2
Y
Pb
Pr
Y
Pb
Pr
INPUT-1COMPONENT VIDEO
AV COMPULINK
SPEAKER INPUT16 45W MAX
1
2
9
8
7
3
3
4
5
4
1
10
6
5
2
FRONT CONTROL KEY & TERMINAL
REAR TERMINAL
MENU Button ( OPERATE )1
CHANNERL -/+ Button ( OPERATE / )2
SPEAKER INPUT7
SUBWOOFER / AUDIO OUT8
AV COMPULINK 9
AUDIO INPUT (For DIGITAL IN)10
VOLUME -/+ Button3
MAIN POWER Button4
POWER LED (Blue)5
INPUT4( AUDIO / VIDEO / S-VIDEO )
6
DIGITAL IN( DVI-D Signal Link 19pin )
1
INPUT 1( AUDIO / VIDEO / S-VIDEO )
2
INPUT 2( AUDIO / VIDEO / S-VIDEO )
3
INPUT 3( AUDIO / VIDEO )
4
COMPONENT VIDEO INPUT 1( Y / Pb / Pr )
5
COMPONENT VIDEO INPUT 2( Y / Pb / Pr )
6
6
AV-65WP74
(No.52096)1-9
RM-C1200G
POWER
VIDEOSTATUS
INPUT2
INPUT3
INPUT4
DIGITAL-IN
INPUT1
SPLIT
100+
3
9
6
RETURN+ /TV
MUTING
MENU
C.C.
BACK
TV CATV VCR DVD
THEATERPRO
NATURALCINEMA
LIGHTSLEEP TIMER DISPLAY SOUND
1
7
4
2
8
0
5
3
9
6
POP
FREEZE SWAP SELECT
INDEX
ASPECT
EZ SURF
+CH
VOL VOL+
CH
OK
REC
OPEN/CLOSE STILL/PAUSE
STOP PAUSE
PLAY FFREW
VCR CHANNELPREV NEXT TV/VCR
VCR/DVDPOWER
MULTI SCREEN14
5
7
9
11
10
6
8
14
12
13
23
15
1617
1918
20
22
23
21
REMOTE CONTROL UNIT [RM-C1200G]
POWER Key1
ASPECT Key2
VCR / DVD Switch3
TV / CATV Switch4
Input select Keys5
THEATER PRO Key6
SLEEP TIMER Key7
DISPLAY Key8
MUTING Key (memory Key)9
Function up / down / right / left Keys(CH + / CH - / VOL + / VOL - Keys)
10
MENU Key11
MULTI SCREEN operation Keys12
Number (1~0)Keys13
100+ Key14
RETURN+ / TV Key15
VIDEO STATUS Key16
NATURAL CINEMA Key17
LIGHT Key18
SOUND Key19
C.C.(Closed Caption) Key20
OK Key21
BACK Key22
VCR / DVD operation Keys23
AV-65WP74
1-10 (No.52096)
DIGITAL-IN TERMINAL FUNCTIONS
PIN ASSIGNMENT
1 RX2-
PinNo. Pin name
2 RX2+
3 GND2/ 4
4 RX4-
5 RX4+
6 SCL
7 SDA
8 NC
9 RX1-
10 RX1+
11 GND1/3
12 RX3-
13 RX3+
PinNo. Pin name
14 5V
15 GND
16 HTPLG
17 RX0-
18 RX0+
19 GND0/5
20 RX5-
21 RX5+
22 GNDC
23 TXC+
24 TXC-
2
3
6
7
8
1
9
10
11
12
13
14
15
16
4
5
18
19
20
21
22
23
24
17
AV-65WP74
(No.52096)1-11
2.3 TECHNICAL INFORMATION2.3.1 MAIN MICRO COMPUTER (CPU) FUNCTION (MN102H75K)
Pin No. Pin name I/O Function1 NC - --------2 /MICON_V I V.sync for OSD3 LB_PRO I Low B protection detection4 NC - --------5 /RST I Main cpu reset input6 NC - --------7 /TEST I +3.3V8 OSD_YS O OSD Ys output9 NC - --------10 NC - --------11 A_MU O Audio muting12 /MICON_H I H sync input13 M_MU O Monitor sound out MUTE14 P46,OSDXI - Keep for OSD15 P45,OSDXO - Keep for OSD16 SDA2 I/O I2C bus (CLK) for MTS17 AC_IN I AC (60Hz) input18 SCL2 O I2C bus (DATA) for MTS19 TU_POW O Tuner power control20 VCOI I LPF input21 PDO O LPF output22 /IP_RESET O Reset23 OSD_YM O OSD YM output24 OSD_B O OSD blue output25 POWER_LED O LED for power26 OSD_G O OSD green output27 OSD_R O OSD red output28 VREF I --------29 IP_ERR I AMDP program load det ect.30 IREF I --------31 COMP I --------32 AVDD I +3.3V33 CLL I For sub CCD34 VREFLS I STD VOL for sub CCD35 SUB_CCD I For sub CCD36 NC - --------37 VSS I GND38 MAIN_CCD I For main CCD39 VREFHS I STD VOL for main CCD40 CLH I For main CCD41 VDD/VPP O +3.3V42 CLK SW1 O IP clock switch
43 CLK SW2 O IP clock switch44 ON_TIM O LED for on timer45 CONVER_RXD O Convergence control46 CONVER TXD I Convergence control47 SBT1 I --------48 NC - --------49 NC - --------50 NC - --------51 NC - --------52 EE_ABL O ACL control53 CHROMA O CHROMA54 DC_COTL O DC control55 NC - --------56 NC - --------57 TU2_AID I Main AFC input58 /LOB_POW O LowB power control59 COMPULINK I AV COMPULINKáVinput60 /POWERGOOD I Power condition check61 MECA_ON I Machine SW interrupt62 /MAIN_POW O Main power control63 NC - --------64 /B1 POW O B1 power control65 C/N I NC66 X_RAY I X-ray protection detection67 NC - --------68 KEY2 I Front key input 269 KEY1 I Front key input 170 SCL1 O I2C bus (CLK) for EEP-ROM71 SDA1 I/O I2C bus (SDA) for EEP-ROM72 REMO I Remote control input73 NC - --------74 VSS I GND75 OSC2 O 4MHz OSC76 OSC1 I 4MHz OSC77 VDD I +3.3V78 SCL0 O I2C bus (CLK) for general79 AP_CLK - --------80 SDA0 I/O I2C bus (SDA) for general81 NC - --------82 NC - --------83 NC - --------84 P_MU O Picture muting
Pin No. Pin name I/O Function
AV-65WP74
1-12 (No.52096)
2.4 MAIN PARTS LOCATION2.4.1 PWB ASS'Y ARRANGEMENT
The PWB ASS'Y is indicated below.• MAIN PWB ASS'Y (SSB-1068A-M2)• RECEIVER PWB ASS'Y (SSB0R268A-M2)• MI-COM & DIST MODULE PWB ASS'Y (SSB0D068A-M2)• POWER & DEF PWB ASS'Y (SSB-2068A-M2)• DEF OSC PWB ASS'Y (SSB0H068A-M2)• LINE FILTER PWB ASS'Y (SSB-9068A-M2)• FRONT RELAY PWB ASS'Y (SSB0L268A-M2)• CONVERGENCE OUT PWB ASS'Y (SSB-5068A-M2)
• DIGITAL CONVERGENCE MODULE PWB ASS'Y• DIGITAL INPUT MODULE PWB ASS'Y• REMOCON SENSOR PWB ASS'Y (SSB-8068A-M2)• R CRT SOCKET PWB ASS'Y (SSB-3168A-M2)• G CRT SOCKET PWB ASS'Y (SSB-3268A-M2)• B CRT SOCKET PWB ASS'Y (SSB-3368A-M2)• G VM PWB ASS'Y (SSB-7268A-M2)• FRONT CONTROL PWB ASS'Y (SSB0L068A-M2)
FRONT CONTROL ASS'Y PROJECTION UNIT
REMOCON SENSORPWB
FRONT CONTROLPWB
CRT SOCKETPWB (R/G/B)
VMPWB (G only)
DIGITAL INPUTMODULE PWB
AV TERMANEL BOARD
(This figure is only MAIN UNIT)
DEF OSCPWB
POWER & DEFPWB
MAIN PWB
RECEIVER PWBLINE FILTERPWB
MI-COM & DISTMODULE PWB
FRONT RELAYPWB
CONVERGENCE OUTPWB
DIGITAL CONVERGENCEMODULE PWB
AV-65WP74
(No.52096)1-13
2.5 SCREEN HANDLING CAUTIONS2.5.1 SCREEN STORAGEStore the SCREEN ASS'Y in a standing position in order to avoid deformation. If the screen is stored horizontally, there is risk ofdeforming the screen face.When necessary to place the SCREEN ASS'Y horizontally, position the screen side upwards and sure to place spacers between thescreen and resting site (floor or stand etc.) to prevent the screen from sagging.2.5.2 SCREEN SURFACESince the screen surface is easily scratched or soiled, use ample care when handling.
2.6 PROJECTION UNIT REPLACEMENT2.6.1 ADJUSTMENT DURING REPLACEMENTWhen replacing the three R, G and B projection units, first replace the R and B units and perform focus / screen / raster centeringadjustmentswith reference to the G unit. Then replace the G unit and perform G focus / screen / convergence adjustment. Finally perform R & B .Convergence adjustments. Use care to simultaneously removes all three-projection units.2.6.2 DISASSEMBLY CAUTIONThe projection units include locations that are not to be disassembled during service. When replacing projection unit parts,disassemble to the state indicated in the figure below.The figure indicates screws and wires that are not to be removed. Use care not to remove these.
SCREEN BRACKET(TOP)
SCREEN BRACKET(RIGHT)
SCREEN BRACKET(BOTTOM)
Leave the screen with protector fresnel lens and double lenticular lens attached. If cannot be disassembled further.
SCREEN BRACKET(LEFT)
SENSOR
SCREEN
FRONT CABINET
SENSOR
SENSOR
SENSOR
A( x 5)A( x 5)
A( x 7)
A( x 7)
DISASSEMBLY PROCEDUREIf the screen or screen panel need tobe replaced, remove the 24 screws A.
Check that tape is applied to the CRT neck.If absent, the deflection yoke can dislodge.
Deflection yoke wires : to connector on POWER & DEF. PWB ASS'Y.[R="RHV", G="GHV", B="BHV"]Convergence yoke wires : to connector on CONVERGENCE PWB ASS'Y.[R="R", G="G", B="B"]
Do not remove screws
Do not disassembly
ANODE wires : to DIVIDER
AV-65WP74
1-14 (No.52096)
2.7 DISASSEMBLY PROCEDURE• Make sure that the power cord is pulled out from the AC wall
socket.2.7.1 SPEAKER GRILLE
(1) Remove 4 screws [ A ] from rear side.(2) Open the door of the FRONT CONTROL BOX and remove
2 screws [ B ] from front side.(3) Take out the SPEAKER GRILLE.
2.7.2 SPEAKER (WOOFER)• Take out the SPEAKER GRILLE
(1) Remove 4 screws [ C ].(2) Take out the WOOFER.(3) Disconnect the speaker wire from speaker terminal.
*Remove the both side speaker same manner.2.7.3 SPEAKER (TWEETER)• Take out the SPEAKER GRILLE
(1) Remove 2 screws [ D ].(2) Take out the TWEETER.(3) Disconnect the speaker wire from speaker terminal.
*Remove the both side speaker same manner.2.7.4 FRONT BOARD• Take out the SPEAKER GRILLE.
(1) Remove 4 screws [ E ].(2) Take out the FRONT BOARD.
2.7.5 FRONT CONTROL BOX• Take out the SPEAKER GRILLE.
(1) Remove 2 screws [ F ] and 2 screws [ G ] attaching theFRONT CONTROL BOX.
(2) Disconnect the connector [BH], [R], [BG] on the FRONTCONTROL PWB.
(3) Take out the FRONT CONTROL BOX.2.7.6 FRONT CONTROL PWB• Take out the SPEAKER GRILLE.• Take out the FRONT CONTROL BOX.
(1) Remove 3 screws [ H ] from rear side of FRONTCONTROL BOX.
(2) Take out the FRONT CONTROL PWB.
Fig.1
Fig.2
C
A
SPEAKER(TWEETER)
SPEAKER(WOOFER)
SPEAKER WIRE
D
F
E
B
G A
FRONT CONTROL BOX
FRONT BOARD
SPEAKER GRILL
H
BH BGR
FRONT CONTROL BOXREAR SIDE
FRONT CONTROL PWB
CAUTION AT DISASSEMBLY
1
35
2
46
65WP74CP-S : DIGITAL INPUT MODULE
POWER CORD
SBconnector
AV JACK BOARD
Prior to disassembly, unplug the power code from the AC outlet without fail. (Turn the power "off".)Short the SB connector [1] pin and [2] pin of the DIGITAL INPUT MODULE. (At the time of assembling)Before the rear panel is inserted into the cabinet, release the short-circuit between the SB connector [1] pin and [2] pin of the DIGITAL INPUT MODULE.After releasing the short-circuit between the SB connectors, do not turn the power on until the rear panel is inserted into the cabinet.Negligence in carrying out the above steps may cause the inactivation of the TV.
AV-65WP74
(No.52096)1-15
2.7.7 SCREEN ASS'Y• Take out the SPEAKER GRILLE.• Take out the FRONT CONTROL BOX.
(1) Remove the 4 screws [ I ] attaching the FRONT BRACKET.(2) Remove 10 screws [ J ] from rear side.(3) Take out the connector [ CN00Z ].(4) Take out the SCREEN ASS'Y.NOTE :
• Please place the SCREEN ASS'Y on a flat table withoutfail.
• Because of the large size, at least two parsons arerecommended for removal and reassemble.
• Use core not to scratch the screen during work.• During assembly, be sure to engage the left and right tabs
with the cabinet mounting positions.• When than sporting the SCREEN ASS'Y, avoid grasping
the top of the screen panel, instead grasp the left and rightareas.
Fig.32.7.8 MIRROR• Take out the SPEAKER GRILLE.• Take out the FRONT CONTROL BOX.• Take out the SCREEN ASS'Y.
(1) Remove 10 screws [ K ] attaching the mirror brackets of theupper, left and right side.
(2) Raise slightly to disengage of the mirror from the bottombracket.(If necessary, loosen the screws attaching thebottom bracket)
(3) Take out the MIRROR.NOTE :
• The MIRROR is front-coated. Do not touch the front of theMIRROR.
• At least 2 persons are recommended for removable andreassemble.
Fig.4
FRONTBRACKET
SCREEN ASS'Y
CN00ZJ
I
MIRROR
BRACKETMIRROR BRACKET
K
AV-65WP74
1-16 (No.52096)
2.7.9 REAR PANEL(1) Loosen 4 screws [ L ].(2) Remove 4 screws [ M ].(3) Raise slightly REAR PANEL upward.(4) Take out the REAR PANEL.NOTE :
• Before the rear panel is inserted into the cabinet, releasethe short-circuit between the [SB] connector (1) pin and(2) pin of the DIGITAL INPUT UNIT. (Refer to "CAUTIONAT DISASSEMBLY" on Page 14).
• After releasing the short-circuit between the [SB]connectors, do not turn the power on until the rear panelis inserted into the cabinet.
• Prior to starting the work, be sure to read the followingwritten instructions on the CAUTION LABEL attached tothe REAR PANEL.
2.7.10 REAR COVER BRACKET(1) Remove 2 screws [ N ].(2) Take out the REAR COVER BRACKET.
Fig.5
2.7.11 REAR COVER• Take out the SPEAKER GRILLE.• Take out the FRONT CONTROL BOX.• Take out the SCREEN ASS'Y.
(1) Remove 2 screws [ O ].(2) Remove 2 screws [ P ] from front side.(3) Slightly pull for backside to disengage of the REAR
COVER from hooks.(4) Take out the REAR COVER.NOTE :
• Because of the large size, at least two persons arerecommended for removal and reassemble.
Fig.6
Prior to starting the work, be sure to read the followingwritten instructions on the CAUTION LABEL attached tothe REAR PANEL.
UNPLUG THE POWER CORD FROM AC OUTLET BEFOREOPEN THE REAR COVER (PANEL).When the rear cover (panel) is removed, follow "CAUTION ATDISASSEMBLY" procedure in the service manual beforeplugging the TV's power cord into an AC outlet. Failure to follow the procedure will result in PERMANENTdamage to some of the television features.
M
L
L
N
REAR PANEL
REAR COVERBRACKET
PARTITION
O
P
P
REAR COVER
AV-65WP74
(No.52096)1-17
2.7.12 PARTITION• Take out the REAR PANEL.
(1) Pull out the PARTITION back ward.2.7.13 MAIN UNIT• Take out the SPEAKER GRILLE.• Take out the connector [BH], [R], [BG] on the FRONT
CONTROL PWB.• Take out the REAR PANEL.
(1) Remove 4 screws [ Q ] from front side.(2) Remove 1 screw [ R ] attaching the MAIN CHASSIS and
BODY.(3) Pull out the MAIN UNIT rear side.NOTE :
• Except for confirmation of projection of images on thescreen and audio output through the speakers, theremoved MAIN UNIT is still workable in the same state asif it is still built in the TV set. Therefore, the MAIN UNIT canbe removed, if necessary, for board diagnosis, electrictesting, etc. apart from confirmation of screen images andaudio output.
• When wire clamps are removed during work, use care torestore them precisely to their original positions.Performance can be affected if these are not returned tothe original positions.
• Because of the large size, at least two persons arerecommended for removal and reassemble.
• When carrying the MAIN UNIT, use care not to drop,shock or shake it.
• Do not stain or damage the lens of the PROJECTIONUNIT.
• Do not look through the PROJECTION UNIT.2.7.13.1 CHECKING THE P.W. BOARDWhen checking the MAIN PWB, POWER & DEF PWB, etc., raisethe MAIN UNIT with the HV DIVIDER side down for the sake ofconvenience. You can checking the POWER & DEF PWB andCONVERGENCE OUT PWB.
Fig.7
2.7.14 LINE FILTER PWB• Take out the REAR PANEL.• Take out the AV JACK BOARD. (Refer to next page)
(1) Disconnect the connector [B], [F] on the LINE FILTERPWB.
(2) Remove 3 screws [ S ] attaching the LINE FILTERBRACKET and earth wire.
(3) Remove 2 screws [ T ] attaching LINE FILTER PWB.(4) Take out the LINE FILTER PWB.
Fig.8
REAR SIDE
BODYQ
MAIN UNITR
LINE FILTER BRACKET
LINE FILTER BRACKET
LINE FILTER PWB
R
S
BF
R
AV-65WP74
1-18 (No.52096)
2.7.15 AV TERMINAL BOARD• Take out the REAR PANEL
(1) Remove 9 screws [ U ].(2) Remove 1 screws [ V ].(3) Pull out the POWER CORD CLAMP from AV TERMINAL
BOARD left side.(4) Remove the nut [ W ] attaching the ANTENNA TERMINAL.(5) Take out the AV TERMINAL BOARD.
2.7.16 DIGITAL INPUT MODULE• Take out the REAR PANEL
(1) Remove 2 screws [ X ] from rear side of the AV TERMINALBOARD.
(2) Take out the DIGITAL INPUT MODULE.NOTE :
• When removing the DIGITAL INPUT MODULE, refer tothe "CAUTION AT DISASSEMBLY" section on page 14.
Fig.9
2.7.17 MAIN CHASSIS• Take out the REAR PANEL.• Take out the AV JACK BOARD. (Refer to next page)• Take out the LINE FILTER BRACKET.
(1) Remove 2 screws [ Y ] both side of the MAIN CHASSIS.(2) Remove 1 screws [ Z ] attaching the earth wire.(3) Pull out the MAIN CHASSIS for back side.NOTE :
• If necessary, remove the anode wires, connectors,respectively.
Fig.10
AV TERMINAL BOARD
X
W V
U
DIGITAL INPUT MODULE
ANTENNA TERMINAL
POWER CORD CLAMP
Y
Y Z
EARTH WIRE
MAIN CHASSIS
AV-65WP74
(No.52096)1-19
2.7.18 PROJECTION UNIT• Take out the SPEAKER GRILLE• Take out the FRONT CONTROL BOX• Take out the REAR PANEL• Take out the MAIN UNIT.
(1) Take out the CRT SOCKET PWB.(2) Remove 4 screws [ a ] attaching the PROJECTION UNIT.(3) Pull out the PROJECTION UNIT, upward.NOTE :
• Refer to "PROJECTION UNIT REPLACEMENT" on page13 when taking out and replacing the PROJECTIONUNIT.
• When wire clamps are removed during work, use care torestore them precisely to their original positions.Performance can be affected if these are not returned tothe original positions.
2.7.19 HV DIVIDER• Take out the REAR PANEL
(1) Remove 1 screws [ b ]?attaching the HV DIVIDER.(2) Take out the HV DIVIDER.
*Wires of the transformer (FBT) and CRT of eachPROJECTION UNIT can be removed by turning theconnector portions.
NOTE :• If necessary, remove the anode wires, and replacing the
HV DIVIDER, take care to correctly engage the [ c ]connector.
2.7.20 REMOCON SENSOR PWB• Take out the REAR PANEL
(1) Remove 1 screws [ d ] attaching the REMOCON SENSORPWB.
(2) Take out the REMOCON SENSOR PWB.
Fig.11
PROJECTION UNIT
REMOCONSENSOR PWB
HV DIVIDER
Pull Turn
a
b
c
d
AV-65WP74
1-20 (No.52096)
2.8 REPLACEMENT OF CHIP COMPONENT
2.8.1 CAUTIONS(1) Avoid heating for more than 3 seconds. (2) Do not rub the electrodes and the resist parts of the pattern.(3) When removing a chip part, melt the solder adequately. (4) Do not reuse a chip part after removing it.
2.8.2 SOLDERING IRON(1) Use a high insulation soldering iron with a thin pointed end of it. (2) A 30w soldering iron is recommended for easily removing parts.
2.8.3 REPLACEMENT STEPS 1. How to remove Chip parts [Resistors, capacitors, etc.]
(1) As shown in the figure, push the part with tweezers andalternately melt the solder at each end.
(2) Shift with the tweezers and remove the chip part.
[Transistors, diodes, variable resistors, etc.] (1) Apply extra solder to each lead.
(2) As shown in the figure, push the part with tweezers andalternately melt the solder at each lead. Shift and removethe chip part.
Note :After removing the part, remove remaining solder from thepattern.
2. How to install Chip parts [Resistors, capacitors, etc.]
(1) Apply solder to the pattern as indicated in the figure.
(2) Grasp the chip part with tweezers and place it on thesolder. Then heat and melt the solder at both ends of thechip part.
[Transistors, diodes, variable resistors, etc.]
(1) Apply solder to the pattern as indicated in the figure. (2) Grasp the chip part with tweezers and place it on the
solder. (3) First solder lead A as indicated in the figure.
(4) Then solder leads B and C.
SOLDER SOLDER
AB
C
A
B
C
AV-65WP74
(No.52096)1-21
2.9 MEMORY IC REPLACEMENT2.9.1 MEMORY ICThis memory IC stores data for proper operation of the video anddeflection circuits.When replacing, be sure to use an IC containing this (initialvalue) data.
Fig.12.9.2 MEMORY IC REPLACEMENT PROCEDURE
(1) Power offSwitch off the power and disconnect the power cord fromthe wall outlet.
(2) Replace the memory ICInitial value must be entered into the new IC.
(3) Power onConnect the power cord to the wall outlet and switch on thepower.
(4) SERVICE MENU settinga) Press [SLEEP TIMER] key and, while the indication of
SLEEP TIMER 0 MIN is being displayed, press[DISPLAY] key and [VIDEO STATUS] key on theremote control unit (Fig.2) simultaneously.
b) The SERVICE MENU screen of Fig.1 is displayed.c) Verify what to set in the SERVICE MENU, and set
whatever is necessary (Fig.1).Refer to the SERVICE ADJUSTMENT for setting.
d) Press the [BACK] key twice to return normal screen.(5) Receive channel setting
Refer to the OPERATING INSTRUCTIONS (USER'SGUIDE) and set the receive channels (Channels Preset) asdescribed.
(6) User settingsCheck the user setting items according to after page.Where these do not agree, refer to the OPERATINGINSTRUCTIONS (USER'S GUIDE) and set the items asdescribed. Fig.2
2.9.3 SERVICE ADJUSTMENT ITEM
SERVICE MENU
SERVICE MENU
1.PICTURE/SOUND2.YC SEP3.WHITE BALANCE4.MEMORY SETUP5.RF AFC6.CONVER A
FACTORY setting F01~F70 PPA001~PPA008 Do not adjust2.YC SEP PPB001~PPB036 Do not adjustYC separation setting YCM001~YCM185 Do not adjust PPC001~PPC008 Do not adjust
YCS001~YCS114 Do not adjust PPD001~PPD025 Do not adjust3.WHITE BALANCE 9.IPLOW LIGHT/HIGH LIGHTadjustment
BR, DRV R, DRV B, CWT R, CWT G,
CWT B
DIST process setting IPA001~IPA120 Do not adjust
4.MEMORY SETUP ------ Do not adjust IPB001~IPB079 Do not adjust5.RF AFC IPC001~IPC044 Do not adjustAFC of TUNER setting TUNER, AFC,FINE Do not adjust IPD001~IPD026 Do not adjust6.CONER A IPE001~IPE015 Do not adjustConvergence adjustment CPA01~CPA08 0.GCR
CCA01CCA09 Ghost re reduction Not useCBA01~CBA80 Do not adjust
AV-65WP74
1-22 (No.52096)
2.9.4 SHIPPING FACTORY SETTINGVIDEO STATUS MEMORY (NTSC / 480p)
3.1 ADJUSTMENT PREPARATION(1) You can make the necessary adjustments for this unit with
either the Remote Control Unit or with the adjustment toolsand parts as given below.
(2) Adjustment with t he Remote Control Unit is made on thebasis of the initial setting values, however, the new settingvalues which set the screen to its optimum condition maydiffer from the initial settings.
(3) Make sure that AC power is turned on correctly.(4) Turn on the power for set and test equipment before use,
and start the adjustment procedures after waiting at least30 minutes.
(5) Unless otherwise specified, prepare the most suitablereception or input signal for adjustment.
(6) Never touch any adjustment setting value which are notspecified in the list for this adjustment.
(7) Presetting before adjustmentUnless otherwise specified in the adjustment instructions,preset the following functions with the remote control unit:
3.2 ADJUSTMENT EQUIPMENT(1) DC voltmeter (or digital voltmeter)(2) Oscilloscope(3) Signal generator (Pattern generator)
[NTSC / 480i / 480p / 720p / 1080i / HDCP](4) TV audio multiplex signal generator(5) Remote control unit
• SETTING POSITION
3.3 ADJUSTMENT FLOWCHARTWHEN REPLACING SCREEN AND PROJECTION UNIT• Contains only the main adjustments. Also confirm other adjustments as required.
Setting item Setting position Setting item Setting positionVIDEO STATUS STANDARD ASPECT FULLBASS / TREBLE / BALANCE CENTER VERTICAL POSITION CENTERHYPER SURROUND OFF BBE ONTINT / COLOR / PICTURE / BRIGHT / DETAIL
CENTER ON/OFF TIMER NO
COLOR TEMPERATURE HIGH AUTO SHUTOFF OFFDIGITAL NOISE CLEAR CENTER
1 Projection unit
Install projection tube
LENS FOCUS
BEAM SPOT
CRT FOCUS
SCREEN & LOW LIGHT
CONVERGENCE(match to unreplaced tube)
HIGH LIGHT
HIGH LIGHT
END
3 Projection unit
Install projection tube
LENS FOCUS
LENS FOCUS
BEAM SPOT
CRT FOCUS
SCREEN & LOW LIGHT
G CONVERGENCE
R CONVERGENCE
B CONVERGENCE
END
SCREEN
N
Y
G convergencedisturbed
R CONVERGENCE
G CONVERGENCE
B CONVERGENCE
END
AV-65WP74
(No.52096)1-25
3.4 ADJUSTMENT LOCATION (1/2)
IC805
B G RY
P BG
BH
BHR
F
M
F
B
CN001
CN002
CN003
S
Q
DC
SY
B
P
J
CN010
CN00M
CN010
CN00Y
CN00E
H
H
BG
G
G
IC804 DIGITAL CONVERGENCEMODULE PWB
FRONT
FRONT
FRONT
TOPPOWER SW
MENU CH - CH +
INPUT 3
VOL - VOL +
AUDIO / VIDEOS-VIDEO
COMPONENTVIDEO-V
AUDIO
POWER SWLED
11Pin : L
2Pin : R
3Pin : GND
4Pin : SOA
5Pin : NC 5
REMOCON SENSOR PWBMI-COM & DIST PWB
CONVERGENCE OUT PWB
R/G/B CRT SOCKET PWB
DIGITAL INPUTMODULE PWB
G VM PWB
G CRTSOCKET
PWB
DIGITAL INPUTMODULE PWB
FRONT CONTROL PWBCONVERGENCE OUT PWB
FRONT RELAY PWB
MAIN PWBPOWER&DEFPWB
RECEIVERPWB
MI-COM&DISTMODULE PWB
DEF OSC PWB
LINE FILTERPWB
POWER CORD
SUB TUNER(TU101)
MAIN TUNER
S
AV-65WP74
1-26 (No.52096)
3.5 ADJUSTMENT LOCATION (2/2)
DC
Q
SY
AB
AAS1
RBN RGNRBN RGN
GBK GBK
RGKRGK
TOP
FRONT
TOP
REAR
SB CONNECTOR
TP-E TP-E
MAIN PWB
FOCUS PACK
HV DIVIDER
5
1
LINE FILTER PWB
M-I COM & DISC MODULE PWBDIGITAL INPUT MODULE PWB
FOCUS PACK
CRT SOCKET PWB
POWER & DEF PWB
VM PWB
DEF OSC PWB
MAIN PWB
G CRT SOCKETPWB
R CRT SOCKETPWB
B CRT SOCKETPWB
FBT
TP-GTP-E TP-R TP-B
E
V
A
B
J
A
CN010
CN001
CN002
CN003
RHV
GHV
BHV
15Pin : TP-91(B1)
4Pin : NC
3Pin : X-ray1
2Pin : X-ray2
1Pin : TP-E ( ) 5
S1
R
R
G
G
B
B
FOCUS
SCREEN
J
V
TOP
AV-65WP74
(No.52096)1-27
3.6 BASIC OPERATION OF SERVICE MENU
SERVICE MENU
1.PICTURE/SOUND2.YC SEP3.WHITE BALANCE4.MEMORY SETUP5.RF AFC6.CONVER A
3.6.1 TOOL OF SERVICE MENU OPERATIONOperate the SERVICE MENU with the REMOTE CONTROL UNIT.3.6.2 SERVICE MENU ITEMSIn general, basic setting (adjustments) items or verifications are performed in the SERVICE MENU.1.PICTURE / SOUND ....This sets the setting values of the VIDEO,AUDIO and DEFLECTION circuits.2.YC SEP.......................This is used when the YC separation circuit is adjusted. [Do not adjust]3.WHITE BALANCE.......This sets the setting values of the WHITE BALANCE.4.MEMORY SETUP.......This sets the setting values of the MEMORY ADDRESS. [Do not adjust]5.RF AFC .......................This is used when the IF VCO is adjusted. [Do not adjust]6.CONVER A .................This is used when the CONVERGENCE is adjusted.7.CONVER B .................This is used when the CONVERGENCE is adjusted.8.PP ...............................This sets the setting value of the output of MULTI-PICTURE circuit.9.IP.................................This sets the setting value of the DIST circuit. [Do not adjust]0.GCR ............................This model do not built-in.
3.6.3 BASIC OPERATIONS OF THE SERVICE MENU(1) How to enter the SERVICE MENU.
Press [SLEEP TIMER] key and, while the indication of "SLEEP TIMER 0 MIN." is being displayed, press [DISPLAY] key and[VIDEO STATUS] key on the remote control unit simultaneously to enter the SERVICE MENU screen as shown in the fig.1.
(2) Releasing SERVICE MENUAfter returning to the SERVICE MENU upon completion of the setting work, press the BACK key again.
3.6.4 DESCRIPTION OF STATUS DISPLAYThe status display on the upper part of the SERVICE MENUscreen is common (to all models).
FULL : FULLPANO : PANORAMACINE : CINEMAREGU : REGULAR
M1 : One screen (for adjustment)M2-1 : SPLIT (4 : 3)M2-2 : SPLIT (16 : 9)M4 : POPM12 : INDEX
ST : STANDARDDA : DYNAMICTH : THEATERGA : GAME
H : HIGHL : LOW
FL : FRAMEL1 : LINE23 : COMPULSORY NATURAL CINEMA IN
MUTE : Press [MUTING] keyDIR : Change data then memory at the same time.
NTSC CINE ST L FL MUTE
A01 IN LEVEL 001
COLORSYSTEMASPECT/MULTIVIDEOSTATUS
MEMORYMODEIP CHANGINMODE
STATUS DISPLAY
WHITEBALANCE
[SERVICE SCREEN]
AV-65WP74
(No.52096)1-29
3.6.5 SERVICE MENU SETTING1. PICTURE/SOUND
AUDIO, VIDEO, DEFLECTION data adjustment.1.SETTING ITEM No.
• Press [CH+] / [CH-] key
• Press [SLEEP TIMER] key
2.SETTING ITEM NAMEDescri6be setting item name
3.SETTING VALUESet the setting value.
• Press [VOL+] / [VOL-] keySet the setting value.
• Press [MUTING] keyMemorize the data.
2. YC SEPYC separation circuit setting [Do not adjust]
3. WHITE BALANCEAdjustment of LOW LIGHT / HIGH LIGHT1.SELECT ITEM• Press [CH+] / [CH-] key2.SETTING VALUEBRIGHT• Press [VOL+] / [VOL-]DRIVE[4] key : DRIVE R is up[7] key : DRIVE R is down[6] key : DRIVE B is up[9] key : DRIVE R is downCUTOFF[4] key : CUTOFF R is up[7] key : CUTOFF R is down[5] key : CUTOFF G is up[8] key : CUTOFF G is down[6] key : CUTOFF B is up[9] key : CUTOFF B is down
4. MEMORY SETUP[Do not adjust]
A : AUDIOS : SIGNALD : DEFLECTIONF : FACTORY SETTING
3.7 INITIAL SETTING VALUE OF SERVICE MENU(1) Adjustment of the SERVICE MENU is made on the basis of the initial setting values; however, the new setting values which set
the screen in its optimum condition may differ from the initial setting.(2) Do not change the initial setting values of the setting items NOT LISTED IN ADJUSTMENT.(3) The (*1 or *2) marked items in following table, it is NO REQUIREMENT for adjustment. If values had change by the missing, set
the initial values in the following table.(4) "---" is not adjusted. Setting value is not displayed
CAUTION:Never change the initial setting value any adjustments except for those that are designated in the adjustment procedures.In case where you have made undesignated adjustments by mistake, never press the [MUTING] key on the remote control unit.Whenever you had not pressed the [MUTING] key, you would be able to recover the initial value by switching the [POWER] key.
3.7.1 [1. PICTURE / SOUND]AUDIO SYSTEM
ItemNo. Item name Variable range Initial setting value
Initial setting value is reference value at following condition.INPUT SIGNAL : NTSCASPECT : FULLMULTI : SINGLEVIDEO STATUS : STANDARDCOLOR TEMPERATURE : LOW
BR (Not display) 000~238 133DRV R (Not display) 000~255 072DRV B (Not display) 000~255 060DRV R (Not display) 000~255 188DRV G (Not display) 000~255 149DRV B (Not display) 000~255 215
Item No. Item name Variable range
Initial setting value
CPA01 OSD H 0~4095 147CPA02 OSD V 0~1023 18CPA03 FINE H 0~4095 1660CPA04 FINE V 0~4095 50CPA05 CAU V 0~4095 3920CPA06 CAU H1 0~65535 0CPA07 CAU H2 0~255 11CPA08 FINE OFF 0 / 1 0CCA01 C H CENT -512~+511 0CCA02 C H SIZE -512~+511 -12CCA03 C H LINE -512~+511 -29CCA04 C H SKEW -512~+511 0CCA05 C EW PIN -512~+511 17CCA06 C H BOW -512~+511 0CCA07 C V CENT -512~+511 0CCA08 C V SKEW -512~+511 0CCA09 C V SIZE -512~+511 -95
Item No. Item name Variable range
Initial setting value
CBA01 LINE COMP 0~3 2CBA02 INTER NUM 0~15 9CBA03 INTERLACE 0 / 1 0CBA04 ADD RATIO 0~3 0CBA05 DAC NUM 0 / 1 1CBA06 CKOUT FRF 0~7 0CBA07 ODD LAVEL 0 / 1 1CBA08 V1CNTUP 0~4095 310CBA09 RETRACE 0 / 1 1CBA10 RV CLAMP 0 / 1 1
AV-65WP74
(No.52096)1-43
3.7.5 [8.PP]NOTE :
Initial setting value is reference value at following condition.
Item Measuringinstrument Test point Adjustment part Description
HIGH VOLTAGEcheck
Signal generator
High voltage meter
CRT Anode (1) Receive NTSC whole black signal.(2) Connect the high voltage meter between CRT anode
and GND.(3) Check that the high voltage DC 31.0kV±1.0kV.
X-RAYPROTECTORcheck
Resistor[6.8k ohm 1/4W ±5%]
S1 connector2 pin : X-Ray23 pin : X-Ray1
(1) Receive any broadcast.(2) Connect resistor 6.8k ohm(1/4W, ±5%) between 2 pin
& 3 pin of the connector S1.(3) Confirm that the X-RAY protector functions operated.
Item Measuring instrument Test point Adjustment part Description
H. FREQUENCYadjustment
Signalgenerator
Remotecontrol unit
[1.PICTURE/SOUND]D15 : H. FREQ.D19 : DEF. RST
(1) Receive any broadcast.(2) Press [ASPECT] key and select FULL mode.(3) Select 1. PICTURE/SOUND from SERVICE MENU.(4) Select <D19> (DEF. RST) and change the data 0 to 1.(5) While observing the screen, adjust the <D15> (H.
FREQ) so that an optimum horizontal synchronizationis obtained.
(6) After adjustment, select <D19> and change the data1 to 0.
(7) Press [MUTING] key to memorize the set value.
AV-65WP74
1-50 (No.52096)
3.8.3 FOCUS & BEAM SPOT ADJUSTMENT
Item Measuring instrument Test point Adjustment part Description
R LENS FOCUS screwG LENS FOCUS screwB LENS FOCUS screw [PROJECTION UNIT (LENS ASS'Y)]
R SCREEN VRG SCREEN VRB SCREEN VR[FOCUS PACK]
4 pole magnet2 pole magnet[PROJECTION UNIT (R / G / B CRT neck)]
R FOCUS VRG FOCUS VRB FOCUS VR[FOCUS PACK]
(1) Receive NTSC cross-hatch signal.(2) Press [ASPECT] key and select FULL mode.(3) If the picture tilted, adjust the R, G and B DY position
to mark straight horizontal line.LENS FOCUS
(1) Makes a red single color.NOTE :
When making a single color, It squeezes SCREENVR in each one, or it does a lid to the lens in of theadjustment color and it makes it single color.
(2) By turning the LENS FOCUS screw (in LENSASS'Y), for optimum focus at the screen center.Check for absence of difference in the peripheralfocus. If the peripheral focus is poor, slightly shift thecenter focus to obtain overall balanced focus.
(3) In the same manner, produce green and blue singlecolor and adjust their respective focus.
(4) After adjustment, it fixes a screw.NOTE :
There is not a difference in the focus in the top and thebottom, on either side, in the diagonal.When the difference of the focus is big, it removes amain lens, and it puts a washer between the mainlens and the coupler and it adjusts it.
BEAM SPOT(5) Receive NTSC dot pattern signal.(6) Makes a red single color.NOTE :
When making a single color, It squeezes SCREENVR in each one, or it does a lid to the lens in of theadjustment color and it makes it single color.
(7) Turn the R FOCUS VR to set the dot diameter toabout Ø30mm.
(8) Turn the 4 pole magnet of the projection unit CRTneck and to where the dots at the screen center arenearly circular.
(9) Return the R FOCUS VR to its original position (justfocus).
(10) Turn the 2 pole magnet of the CRT neck to minimizeexpansion of the dots.
(11) In the same manner, adjust for the green and bluesingle color focus.
(12) Secure the 4 and 2 pole magnets with similaradhesive.
CRT FOCUS(13) Receive NTSC crosshatch signal.(14) Makes a red single color.
NOTE :When making a single color, It squeezes SCREENVR in each one, or it does a lid to the lens in of theadjustment color and it makes it single color.
(15) Adjust the R FOCUS VR for optimum focus at theposition indicated in the figure.
(16) In the same manner, adjust for the green and bluesingle color focus.
(17) After adjustment, return the SCREEN VRs to theiroriginal positions.
NOTE :When moving screen VR, always return to original.
LENS FOCUS SCREW
DEFLECTIONYOKE
CENTERING MAGNET
4 POLE MAGNET
PROJECTION UNIT & LENS ASS'Y(CRT adjustment location)
2 POLE MAGNET
CRT FOCUS adjustment point
AV-65WP74
(No.52096)1-51
3.8.4 DEFLECTION & CONVERGENCE ADJUSTMENT• The adjustment using the remote control unit is made on the basis of the initial setting values.• The setting values which adjust the screen to the optimum condition can be different from the initial setting values.• At first the adjustment in FULL mode should be done, then the data for the other ASPECT mode is corrected in the respective value
at the same time.3.8.4.1 FLOWCHART OF ADJUSTMENTCAUTION:
All adjustments of the DEFLECTION circuit for this model should be carried out under the status without convergence operation.To enter the mode without convergence operation, select 1.PICTURE/SOUND and change the data in the setting item F62 from 0to 1. (For details, please refer to the adjustment of DEFLECTION.)As a result, you can get the screen as shown in bellow figure. Adjust the DEFLECTION circuit in order of the steps indicated by thedownward arrows.NOTE: When every adjustment of the DEFLECTION circuit has completed, start the adjustment of convergence.
PREPARATION
DEFLECTION CONVERGENCE
Withoutconvergenceoperation
Overall position & size
Center
Center perimeter(If center deviated, readjust)
Perimeter(If center deviated, readjust)
Center (Final adjust) R and B only
Crosshatch Completed(From a collection of squares)
PASTERCENTERING& H.POSITION /SIZE(coarse)
V.POSITION / SIZE /LINEARITY
CONVERGENCEPHASE
OVERALLCONVERGENCE
SCREEN TILT
H.SIZE
SIDE PIN
TRAPEZIU
H.POSITION
Adjustmentlocation
sequence
AV-65WP74
1-52 (No.52096)
3.8.4.2 PREPARATION
Item Measuring instrument Test point Adjustment part Description
SCREEN TILT adjustment
Signalgenerator
Remotecontrol unit
[1.PICTURE/SOUND]F62 : Without convergence operation
G DEF. YOKER DEF. YOKEB DEF. YOKE[PROJECTION UNIT]
• Confirm correct FOCUS adjustment.(1) Receive NTSC cross-hatch signal.(2) Select 1. PICTURE/SOUND from SERVICE MENU.(3) Select <F62> (Without convergence operation) with
[CH +] / [CH -] keys.(4) Change the data 0 to 1, then it makes picture without
convergence operation.(5) Makes a green single color.NOTE :
When making a single color, It squeezes SCREENVR in each one, or it does a lid to the lens in theadjustment color and it makes it single color.
(6) Temporarily secure the G deflection yoke to the topof the neck and adjust the tilt of the deflection yokeso that the horizontal line at the center becomes flat.After adjustment, fasten the temporal screw.
(7) Adjust the tilt of the R and B deflection yokes in thesame manner as for green.
NOTE :Make sure that the adjustment of CRT FOCUS isoptimized at the center and at the fringe of the centerin turn. If the proper adjustment has not been done,adjust FOCUS VR again.
RASTERCENTERING & H. POSITION / SIZE (coarse) adjustment
Signalgenerator
Remotecontrol unit
[1.PICTURE/SOUND]D03 : H. SIZED14 : H. CENTER F62 : Without convergence operation
G CENTERING magnetR CENTERING magnetB CENTERING magnet[DEF. YOKE]
(1) Receive NTSC circle (or cross-hatch) signal.(2) Select 1. PICTURE/SOUND from SERVICE MENU.(3) Select <F62> (Without convergence operation) with
[CH +] / [CH -] keys.(4) Change the data 0 to 1, then it makes picture without
convergence operation.(5) Makes a green single color.NOTE :
When making a single color, it squeezes SCREENVR in each one, or it does a lid to the lens in theadjustment color and it makes it single color.
(6) Select <D03> (H. SIZE) and shorten the level untiland perpendicular amplitude of vibration with untilthe blanking in Left and Right and on either side canbe seen.
(7) Select <D14> (H. CENTER) and adjust horizontalposition to make the screen center and signalcenter.
(8) Select <D03> and adjust horizontal size to makescreen picture approx. 92% of H-SIZE.
(9) After adjustment, select <F62> and change the data1 to 0.
(10) Press [MUTING] key and memorize the set value.(11) Adjust G CENTERING magnet to make horizontal
and vertical line center as mechanical center ofscreen.
(12) Red and blue color too, are reflected by it.(13) Using R CENTERING magnet and B CENTERING
magnet, adjusts for the line of the red(L1) and theblue(L2) to become the position of the left figure.
NOTE :Vertical center position of the red and blue are thesame as green.
0F62
1. PICTER/SOUND menu
Select item Change value0 1
R G B
L2
L1=30mm L2=45mm
L1
AV-65WP74
(No.52096)1-53
3.8.4.3 DEFLECTION ADJUSTMENT
Item Measuring instrument Test point Adjustment part Description
V. POSITION / SIZE / LINEARITYadjustment
Signalgenerator
Remotecontrol unit
[1.PICTURE/SOUND]D01 : V. SIZED05 : V. LINED06 : V. CENTF62 : Without convergence operation
• To memorize every time after finish adjustment on eachmode.(1) Receive NTSC circle pattern signal.(2) Select FULL mode with [ASPECT] key.(3) Select 1. PICTURE/SOUND from SERVICE MENU.(4) Select <F62> (Without convergence operation).(5) Change the data 0 to 1, then it makes picture without
(V. CENT).(7) Adjust <D01>, <D05> and <D06> to make A = B
(precision ±2mm), and adjust to make C = 80mm(8) Press [MUTING] key and memorize the set value.NOTE :
Do not adjust <D04> (V. S-CORRECTION), if it isdifferent vertical position after adjust vertical linearity,to adjust vertical position.
H. POSITIONadjustment
Signalgenerator
Remotecontrol unit
[1.PICTURE/SOUND]D14 : H. CENTERF62 : Without convergence operation
(1) Receive NTSC circle pattern signal.(2) Select FULL mode with [ASPECT] key.(3) Select 1. PICTURE/SOUND from SERVICE MENU.(4) Select <F62> (Without convergence operation).(5) Change the data 0 to 1, then it makes picture without
convergence operation.(6) Select <D14> (H. CENTER).(7) Adjust <D14> to make D = E as shown figure.(8) Press [MUTING] key and memorize the set value.
H. SIZE adjustment
Signalgenerator
Remotecontrol unit
[1.PICTURE/SOUND]D03 : H. SIZEF62 : Without convergence operation
(1) Receive NTSC cross-hatch signal.(2) Select FULL mode with [ASPECT] key.(3) Select 1. PICTURE/SOUND from SERVICE MENU.(4) Select <F62> (Without convergence operation).(5) Change the data 0 to 1, then it makes picture without
convergence operation.(6) Select <D03> (H. SIZE).(7) Adjust <D03> to make sure that the vertical screen
size of the picture size is 92%.(8) Press [MUTING] key and memorize the set value.
(1) Receive NTSC cross-hatch signal.(2) Select FULL mode with [ASPECT] key.(3) Select 1. PICTURE/SOUND from SERVICE MENU.(4) Select <F62> (Without convergence operation).(5) Change the data 0 to 1, then it makes picture without
(TOP.CORN).(7) Adjust <D02>, <D08>, <D09> to make the vertical
lines at the left and right edges of the screen straight.(8) Press [MUTING] key and memorize the set value.NOTE :
After making adjustments, confirm that the horizontalposition is properly adjusted. If the horizontal is out ofalignment, readjust it. Adjust H SIZE & SIDE PINreparably.
TRAPEZIUMadjustment
Signalgenerator
Remotecontrol unit
[1.PICTURE/SOUND]D07 : EW.TRAPF62 : Without convergence operation
(1) Receive NTSC cross-hatch signal.(2) Select FULL mode with [ASPECT] key.(3) Select 1. PICTURE/SOUND from SERVICE MENU.(4) Select <F62> (Without convergence operation).(5) Change the data 0 to 1, then it makes picture without
convergence operation.(6) Select <D07> (EW.TRAP).(7) Adjust <D07> to bring the vertical lines at the right
and left edges of the screen parallel.(8) Press [MUTING] key and memorize the set value.NOTE :
After making adjustments, confirm that the horizontalposition is properly adjusted. If the horizontal is out ofalignment, readjust it. Adjust H SIZE & SIDE PINreparably.
Item Measuring instrument Test point Adjustment part Description
Straight
Parallel
AV-65WP74
(No.52096)1-55
3.8.4.4 CONVERGENCE ADJUSTMENT(1) ••••••• RGB together
Item Measuring instrument Test point Adjustment part Description
CONVERGENCEPHASE adjustment
Signalgenerator
Remotecontrol unit
[6.CONVER A]CPA03 : FINE HCPA04 : FINE VCPA05 : CAU VCPA07 : CAU H2
NOTE:Retain the default value of this adjustment. It is notnecessary to carry out the adjustment unless the imageon the screen is significantly deformative. If youperformed this adjustment, open the user MENU"INITIAL SETUP" and execute AUTO ofCONVERGENCE after the adjustment.(1) Receive NTSC cross-hatch signal.(2) Select 6.CONVER A from SERVICE MENU.(3) Select <CPA03> (FINE H).(4) Adjust the peak A as shown in Fig. 2 agrees with the
horizontal center line by using [ 2 ] & [ 8 ] keys.(5) Select <CPA04> (FINE V).(6) Adjust the peak B as shown in Fig. 3 agrees with the
vertical center line by using [ 4 ] & [ 6 ] keys.(7) Select <CPA05> (CAU V).(8) Adjust the intersection point of the horizontal center
line and the vertical center line agrees with thescreen center by using [ 2 ] & [ 8 ]. (Fig.4)
(9) Select < CPA07>(CAU H2).(10) Adjust the intersection point of the horizontal center
line and the vertical center line agrees with thescreen center by using [ 4 ] & [ 6 ]. (Fig.5)
(11) Press [MUTING] key and memorize the set values.
Horizontal center line
A
Vertical center lineScreen center
B
Fig. 1:Screen center
Fig. 2:CPA03<FINE H> adj.
Fig. 4:CPA05<CAU V> adj.
Fig. 3:CPA04<FINE V> adj.
Fig. 5:CPA07<CAU H> adj.
RM-C1200G
POWER
VIDEOSTATUS
INPUT2
INPUT3
INPUT4
DIGITAL-IN
INPUT1
SPLIT
100+
3
9
6
RETURN+ /TV
MUTING
MENU
C.C.
BACK
TV CATV VCR DVD
THEATERPRO
NATURALCINEMA
LIGHTSLEEP TIMER DISPLAY SOUND
1
7
4
POP
FREEZE SWAP SELECT
INDEX
ASPECT
EZ SURF
+CH
VOL VOL+
CH
OK
REC
OPEN/CLOSE STILL/PAUSE
STOP PAUSE
PLAY FFREW
VCR CHANNELPREV NEXT TV/VCR
VCR/DVDPOWER
MULTI SCREEN
REMOTE CONTROL KEY POSITION
2
8
0
5 Number keyScreen centeradjustment[2] : Up[4] : Left[6] : Right[8] : Down
Item Measuring instrument Test point Adjustment part Description
OVERALL CONVERGENCEadjustment (1)[LINE SPHPE]
Signalgenerator
Remotecontrol unit
[ 6.CONVER A ]CPA08 : FINE OFFCCA01 : C H CENTCCA02 : C H SIZECCA03 : C H LINCCA05 : C EW PINCCA09 : V SIZECCA10 : V KEYCCA11 : TB PIN
NOTE:Retain the default value of this adjustment. It is notnecessary to carry out the adjustment unless the image onthe screen is significantly deformative. If you performedthis adjustment, open the user MENU "INITIAL SETUP"and execute AUTO of CONVERGENCE after theadjustment.(1) Receive NTSC cross-hatch signal.(2) Select 6.CONVER A from SERVICE MENU.(3) Select <CPA08> (FINE OFF).(4) Change the data 0 to1. (Clear the fine adjustment data)(5) Press [INPUT] key to select <CCA01> (C H CENT).
Then a green cross-hatch pattern for adjustment will bedisplayed on the screen.
(6) Make sure that the heavy lines as shown in figure arealmost in alignment with the lines of the green cross-hatch pattern (reference color). If the lines are out ofalignment significantly, adjust <CCA02> (C H SIZE),<CCA03> (C H LIN), <CCA05> (C EW PIN), <CCA09>(V SIZE) and <CCA11> (TB PIN), respectively. (Referto under figure)
(7) Press [SELECT] key to change the adjusting color tored and blue, in turn, and make the adjustments in thesame manner as for 6. above.*In adjustments for red and blue, the adjustment of<CCA10> (V KEY) is also available.
NOTE:Press [OK] key to change the display colors.Whenever [OK] key is pressed, the menu willsequence in this order: "Two colors (adjustingcolor+green)"--->"Three colors (RGB)"
(8) When the adjustments have been completed, press[MUTING] key and memorize the set values.
(9) Select <CPA08>.(10) Change the <CPA08> 1 to 0.(11) Press [MUTING] key and memorize the set values.
<CCA02> H. SIZE
<CCA03> C H LIN <CCA10> V KEY
<CCA11> TB PIN
PARALLEL
STRAIGHT
A BA=B
<CCA05> EW PIN
<CCA09> V. SIZE
STRAIGHT
STRAIGHTSTRAIGHT
For this adjustment, it is necessary to use a remote control unit (e.g. RM-C322G) with INPUT key. In order to change the adjusting items, use INPUT key. When you press INPUT key, the adjusting items will change in the order of CPA CCA CBA key.
Cursor
473mm247mm
1440mm
222mm
183mm
810mm
Fourth lines from the vertical center line upward and downward.
Fourth lines from the horizontal center line right
118mm
RM-C1200G
POWER
VIDEOSTATUS
INPUT2
INPUT3
INPUT4
DIGITAL-IN
INPUT1
SPLIT
100+
3
9
6
RETURN+ /TV
MUTING
MENU
C.C.
BACK
TV CATV VCR DVD
THEATERPRO
NATURALCINEMA
LIGHTSLEEP TIMER DISPLAY SOUND
1
7
4
2
8
0
5
POP
FREEZE SWAP SELECT
INDEX
ASPECT
EZ SURF
+CH
VOL VOL+
CH
OK
REC
OPEN/CLOSE STILL/PAUSE
STOP PAUSE
PLAY FFREW
VCR CHANNELPREV NEXT TV/VCR
VCR/DVDPOWER
MULTI SCREEN
REMOTE CONTROL KEY POSITION
SELECT keyFor adjusting color change
Item No.change [CH+] : up [CH- ] : down
CH+ / CH- key
Setting value change [VOL+] : up [VOL -] : down
VOL+ / VOL- key
MUTING keyFor storing adjustmentdata in memory
OK keyFor display colors change for adjusting
INPUT key
[RM-C322G]
CPA CCA CBA
AV-65WP74
(No.52096)1-57
OVERALL CONVERGENCEadjustment (2)[POINT]
Signalgenerator
Remotecontrol unit
[ 7.CONVER B ] NOTE:Perform this adjustment after performing OVERALLCONVERGENCE adjustment (1).(1) Select 7.CONVER B from SERVICE MENU. Then
appear green cross-hatch pattern for adjustment.(See Fig.1)
(3) Press [CH+] / [CH-] / [VOL+] / [VOL-] key, adjust theposition of the adjusting point so that it is located atthe place as shown in Fig1.
(4) Press [SELECT] key to select the red and bluecross-hatch patterns, respectively, and makeconvergence adjustments so that they align with theadjusting points of the green cross-hatch pattern(reference color).
(5) Press [OK] key to change the display colors to threecolors from two colors (adjusting color + green) andmake sure that the convergence has been alignedwith each other.
(6) Press [INPUT 2] or [INPUT4] key. After changing thepattern to the fine grid cross-hatch pattern, makesure that the convergence has been adjustedproperly.
(7) Press [MUTING] key and memorize the set values.
Item Measuring instrument Test point Adjustment part Description
Number keyFor cursor shifting [2] : up [4] : left [6] : right [8] : down
VOL+ / VOL-CH+ / CH- keysFor convergence adjustments [CH+] : up [CH- ] : down [VOL+] : left [VOL -] : right
MUTING keyFor storing adjustment data in memory
OK keyFor display colors change for adjusting
AV-65WP74
1-58 (No.52096)
3.8.5 VIDEO ADJUSTMENT
Item Measuring instrument Test point Adjustment part Description
A-DCONVERTEROFFSETadjustment (1)
Signalgenerator
Remotecontrol unit
[1.PICTURE/SOUND]F44 : Image adjustmentF45 : Image adjustment of mode changeF47 : Minimum valueB at the time ofdetectionF48 : Maximum valueA at the time ofdetection
[8.PP]ADM012 : R offsetAMD013 : G offsetAMD014 : B offset
(1) Input the 480i (DVD) whole black signal from theCOMPONENT VIDEO terminal.
(2) Select STANDARD mode with [VIDEO STATUS]key.
(3) Select FULL mode with [ASPECT] key.(4) Select 1.PICTURE / SOUND from SERVICE MENU.(5) It goes into the zero mode screen of difference
adjustment of color, using <F44>(Image adjustment)as 0 to 1, and using <F45>(Image adjustment modechange) as 0 to 3.
(6) Set <F47> (minimum value B at the time ofdetection) to 0 and <F48> (maximum value A at thetime of detection) to 0.
(7) Press [MUTING] key and memorize the set value.(8) Press [BACK] key and display SERVICE MENU
screen again.(9) Select 8. PP from SERVICE MENU.
(10) Adjust <ADM012> (R offset setup) and <ADM014>(B offset setup) so that the adjustment result out putscreen in the upper half of a screen becomes blackcolor.(Fig.1)
(11) If the screen is reddish, adjust <ADM012>(R offsetsetup) so that the redness is reduced to theminimum.
(12) If the screen is bluish, adjust <ADM014>(B offsetsetup) so that the blue is reduced to the minimum.
(13) Press [MUTING] key and memorize the set value.
[BRIGHTNESS ADJUSTMENT for SPLIT RIGHTSCREEN]
(1) Select STANDARD mode with [VIDEO STATUS]key.
(2) Select FULL mode with [ASPECT] key.(3) Press [SPLIT] key to enter the SPLIT screen mode,
then input gray scale signal on both left and rightchannels.
(4) Select 1.PICTURE/SOUND from SERVICE MENU.(5) It goes into the Y adjustment MAX mode, using
<F45> as 0 and using <F44> as 0 to 1.(6) Set <F47> to 16 and <F48> to 16.(7) Press [MUTING] key and memorize the set value.(8) Press [BACK] key and display the SERVICE MENU.(9) Select 8. PP from SERVICE MENU.
(10) Adjust <ADM013> (G offset setup) so that thescreen on the right upper side becomes slightlywhitish rather (6% black) than whole black.(Fig.2)
(11) Press [MUTING] key and memorize the set value.
To be slightly whitish rather than whole black
Fig. 1 <FULL screen>
Fig. 2 <SPLIT screen>
Upper side of screen whole black
AV-65WP74
(No.52096)1-59
A-DCONVERTEROFFSETadjustment (2)
Signalgenerator
Remotecontrol unit
[1.PICTURE/SOUND]F44 : Image adjustmentF45 : Image adjustment of mode changeF47 : Minimum valueB at the time ofdetectionF48 : Maximum valueA at the time ofdetection
[8.PP]ADM012 : R offsetAMD013 : G offsetAMD014 : B offset
[WHITE BALANCE LOW LIGHT ADJUSTMENT forSPLIT RIGHT SCREEN]
(1) Press [SPLIT] key to enter the SPLIT screen mode.(2) Select STANDARD with [VIDEO STATUS] key.(3) Select FULL mode with [ASPECT] key.(4) Select 1 PICTURE SOUND from SERVICE MENU.(5) It goes into the zero mode screen of difference
adjustment of color, using <F45>(Image adjustmentmode change) as 0 to 3 and <F44>(Imageadjustment) as 0 to 1.
(6) Set <F47> (minimum value B at the time ofdetection) to 0 and <F48> (minimum value A at thetime of detection) to 0.
(7) Press [MUTING] key and memorize the set value.(8) Press [BACK] key and back to SERVICE MENU.(9) Select 8.PP from SERVICE MENU.
(10) Adjust <ADM012> (R offset setup) and <ADM014>(G offset setup) so that right upside screen becomeswhole black.
(11) Press [MUTING] key and memorize the set value.(12) Select 1.PICTURE/SOUND from SERVICE MENU.(13) Change the data of <F44> 1 to 0 and <F45> 3 to 0.(14) Press [MUTING] key and memorize the set value.
Item Measuring instrument Test point Adjustment part Description
CUTOFF) key so that a black portion may becomeblack.
(7) Press [MUTING] key and memorize the set values.(8) Input 480i component black & white pattern signal
from COMPONENT VIDEO terminal.(9) Repeat steps 5 ~ 7 above.
(10) Input 1080i component black & white signal fromCOMPONENT VIDEO terminal.
(11) Repeat steps 5 ~ 7 above.NOTE :
Before starting the adjustment, warm up the unit formore than 30 minutes.
Item Measuring instrument Test point Adjustment part Description
BRBRIGHT LEVEL
Setting value
DRVDRIVE RR
BG BCUTCUTOFF
3. WHITE BALANCE
NTSCSETTING VALUE
BR 133
DRV R 073
CUT R 188
B 060
G 149 B 215
480iBR
DRV R 074
CUT R 194
B 058
G 149 B 210
1080iBR
DRV R 074
CUT R 195
B 058
G 149 B 210
REMOTE CONTROL UNIT
EXIT
R CUTOFF
1 2 3
4 5 6
7 8 9
0
B CUTOFFG CUTOFF
R CUTOFF B CUTOFFG CUTOFF
OSD ON/OFF
AV-65WP74
1-62 (No.52096)
WHITEBALANCE(HIGH LIGHT)adjustment
Signalgenerator
Remotecontrol unit
[1.PICTURE/SOUND]S10: DRIVE RS12: DRIVE B
(1) Receive NTSC black & white signal (color off).(2) Select STANDARD mode with [VIDEO STATUS]
key.(3) The COLOR TEMP is set at LOW mode.(4) Select 1.PICTER/SOUND from SERVICE MENU.(5) Select <S10> (DRIVE R) or <S12> (DRIVE B).(6) Adjust <S10> or <S12> so that the natural white
should be visible.(7) Press [MUTING] key and memorize the set values.(8) Input 480i component black & white signal from
COMPONENT VIDEO terminal.(9) Repeat steps 5 ~ 7 above.
(10) Input 1080i component black & white signal fromCOMPONENT VIDEO terminal.
(11) Repeat steps 5 ~ 7 above.
SUB BRIGHTadjustment
Signalgenerator
Remotecontrol unit
[1.PICTURE/SOUND]S03: BRIGHT
(1) Receive NTSC black & white signal.(2) Select STANDARD mode with [VIDEO STATUS]
key.(3) The COLOR TEMP is set at the LOW mode.(4) Select 1.PICTURE/SOUND from SERVICE MENU.(5) Select <S03> (BRIGHT).(6) Set initial setting value. (See Table1)(7) If the brightness is not the best with the initial setting
value, make fine adjustment until you get the bestbrightness.
(8) Press [MUTING] key and memorize the set values.(9) Select THEATER mode with [VIDEO STATUS] key.
(10) Select 1.PICTURE/SOUND from SERVICE MENU.(11) Select <S03>. (12) Set initial setting value. (See Table1)(13) If the brightness is not the best with the initial setting
value, make fine adjustment until you get the bestbrightness.
(14) Press [MUTING] key and memorize the set values.(15) Input 480i component black & white signal from
COMPONENT VIDEO terminal.(16) Repeat steps 2 ~ 14 above.(17) Input 1080i component black & white signal from
COMPONENT VIDEO terminal.(18) Repeat steps 2 ~ 14 above.
Table 1
Item Measuring instrument Test point Adjustment part Description
Setting Item Setting valueDRIVE RS10
1. PICTUER/SOUNDNTSC FULL DA H FL MUTE
Item
S10 073 074 074
NTSC 480i 1080i
Setting value
INITIAL SETTING VALUE
S12 060 058 058
SignalItem
S03STANDARD THEATER
NTSC 480i 1080i
Setting value
131 121
STANDARD THEATER
129
STANDARD THEATER
130130 130
AV-65WP74
(No.52096)1-63
SUB CONTRASTadjustment
Signalgenerator
Remote control unit
[1.PICTURE/SOUND]S04: CONTRAST
(1) Receive NTSC black & white signal.(2) Select STANDARD mode with [VIDEO STATUS]
key.(3) The COLOR TEMP is set at the LOW mode.(4) Select 1.PICTURE/SOUND from SERVICE MENU.(5) Select <S04> (CONTRAST).(6) Set Initial setting value. (See Table 2)(7) If the contrast is not the best with the initial setting
value, make fine adjustment of the <S04> until youget the optimum contrast.
(8) Press [MUTING] key and memorize the set values.(9) Select THEATER mode with [VIDEO STATUS] key.
(10) Select 1.PICTURE/SOUND from SERVICE MENU.(11) Select <S04>.(12) Set Initial setting value. (See Table 2)(13) If the contrast is not the best with the initial setting
value, make fine adjustment of the <S04> until youget the optimum contrast.
(14) Input 480i component black & white signal fromCOMPONENT VIDEO terminal.
(15) Repeat steps 2 ~ 13 above.(16) Receive 1080i component black & white signal from
COMPONENT VIDEO terminal.(17) Repeat steps 2 ~ 13 above.
Table 2
SUB COLOR / SUB TINT / B-Y GAINadjustment (1)
Signal generator
Remote control unit
TP-RTP-BTP-E (GND)
[1.PICTURE/SOUND]S01 : COLORS02 : TINTS07 : B-Y
[ Method of adjustment without measuring instrument ](1) Receive NTSC color bar signal.(2) Select STANDARD mode with [VIDEO STATUS]
key.(3) Select 1.PICTURE/SOUND from SERVICE MENU.(4) Select <S01> (COLOR) or <S02> (TINT).(5) Set the initial setting values.(6) If the color or tint is not the best with the initial setting
values, make fine adjustment until you get the bestcolor or the best tint.
(7) Select <S07> (B-Y).(8) Set the initial setting values.(9) If the color bar is not clearly with the initial setting
value, make fine adjustment until you get the clearlycolor bar.
(10) Press [MUTING] key and memorize the set values.(11) Select THEATER mode with [VIDEO STATUS] key.(12) Select <S01> or <S02> .(13) Set the initial setting values.(14) If the color or tint is not the best with the initial setting
values, make fine adjustment until you get the bestcolor or the best tint.
(15) Select <S07>.(16) Set the initial setting values.(17) If the color bar is not clearly with the initial setting
value, make fine adjustment until you get the clearlycolor bar.
(18) Press [MUTING] key and memorize the set values.(19) Input 480i component color bar signal from
COMPONENT VIDEO terminal.(20) Repeat steps 2 ~ 18 above.(21) Input 480p component color bar signal from
COMPONENT VIDEO terminal.(22) Repeat steps 2 ~ 18 above.(23) Input 1080i component color bar signal from
COMPONENT VIDEO terminal.(24) Repeat steps 2 ~ 18 above.
Item Measuring instrument Test point Adjustment part Description
SignalItem
S04STANDARD THEATER
NTSC 480i 1080i
Setting value
052 045
STANDARD THEATER
046
STANDARD THEATER
044065 065
AV-65WP74
1-64 (No.52096)
SUB COLOR / SUB TINT / B-Y GAINAdjustment (2)
Signal generator
Oscilloscope
Remote control unit
TP-RTP-BTP-E (GND)
[1.PICTURE/SOUND]S01 : COLORS02 : TINTS07 : B-Y
[ Method of adjustment with measuring instrument ](1) Receive NTSC color bar signal.(2) Select STANDARD mode with [VIDEO STATUS]
key.(3) Connect the oscilloscope to TP-R on the R CRT
SOCKET PWB.(4) Select 1.PICTURE/SOUND from SERVICE MENU.(5) Select <S01> (COLOR) or <S02> (TINT).(6) Adjust <S01> and <S02> to be following setting
value A[V]. (Refer to the bellow table)(7) Press [MUTING] key and memorize the set values.(8) Select THEATER mode with [VIDEO STATUS] key.(9) Adjust <S01> and <S02> to be following setting
value B[V] same as above. (Refer to the bellowtable)
(10) Press [MUTING] key and memorize the set values.(11) Select STANDARD mode with [VIDEO STATUS]
key.(12) Connect the oscilloscope to TP-B on the B CRT
SOCKET PWB.(13) Adjust <S07> (B-Y) to be setting value C[V]. (Refer
to the bellow table)(14) Press [MUTING] key and memorize the set values.(15) Select THEATER mode with [VIDEO STATUS] key.(16) Adjust <S07> to be setting value D[V]. (Refer to the
bellow table)(17) Press [MUTING] key and memorize the set values.(18) Confirm that LOW-LIGHT is not different after
adjusting COLOR, TINT and B-Y GAIN. If it is greenor magenta, to adjust LOW-LIGHT again. If adjustagain, to set offset value again.
(19) Press [MUTING] key and memorize the set values.(20) Input 480i component color bar from COMPONENT
VIDEO terminal.(21) Repeat steps 2 ~ 19 above.(22) Input 480p component color bar from COMPONENT
VIDEO terminal.(23) Repeat steps 2 ~ 19 above.(24) Input 1080i component color bar from
COMPONENT VIDEO terminal.(25) Repeat steps 2 ~ 19 above.
Fig.1
Fig.2
Table
Item Measuring instrument Test point Adjustment part Description
W
Y R(W-Y) (W-R)
0
(-)
(+)
W(W-B)
B
0
(-)
(+)
Setting item
Signal
STANDARD THEATER STANDARD THEATER
Setting valueA [V]
Setting valueB [V]
SettingvalueC [V]
S01(W-R)
S02 (W-Y)
S01 (W-R)
S02 (W-Y)
S07 (W-B)
S07 (W-B)
Setting valueD [V]
NTSC +28
1080i +7
480p +19
480i +19
+14
+6
+14
+11
+19
+5
+11
+7
+7
+7
+2
+1
+10
-24
-25
-17
+18
-9
+12
+2
AV-65WP74
(No.52096)1-65
MTS INPUTLEVELcheck
Remotecontrol unit
[1.PICTURE/SOUND]A01 : IN LEVEL
(1) Select 1.PICTURE / SOUND from SERVICE MENU.(2) Select <A01> (IN LEVEL).(3) Verify that<A01> is set at its initial setting value.
MTS SEPARATIONadjustment
TV audio multiplex signal generator
Oscilloscope
Remote control unit
AUDIO OUTL outputR output
[1.PICTURE/SOUND]A02: LOW SEP.A03 : HI SEP.
(1) Input stereo L signal (300Hz) from the TV audiomultiplex signal generator to the antenna terminal.
(2) Connect an oscilloscope to L OUTPUT pin of theAUDIO OUT, and display one cycle portion of the300Hz signal.
(3) Change the connection of the oscilloscope to ROUTPUT pin of the AUDIO OUT, and enlarge thevoltage axis.
(4) Select <A02> (LOW SEP.).(5) Set the initial setting value of <A02>.(6) Adjust <A02> so that the stroke element of the
300Hz signal will become minimum.(7) Change the signal to 3kHz, and similarly adjust
<A03> (HI SEP.).
Item Measuring instrument Test point Adjustment part Description
L-Channelsignal waveform
R-Channelcrosstalk portion
Minimum
1 cycle
AV-65WP74
1-66 (No.52096)
3.9 HOW TO CHECK THE HIGH VOLTAGE HOLD DOWN CIRCUIT3.9.1 HIGH VOLTAGE HOLD DOWN CIRCUITAfter repairing the high voltage hold down circuit.This circuit shall be checked to operate correctly.3.9.2 CHECKING OF THE HIGH VOLTAGE HOLD DOWN CIRCUIT
(1) Turn the power switch ON.(2) As shown in figure bellow, set the resistor (between S1 connector 2 & 3).(3) Make sure that the screen picture disappears (no raster).(4) Temporarily unplug the power cord.(5) Remove the resistor (between S1 connector 2 & 3).(6) Again plug the power cord, make sure that normal pictures is displayed on the screen.
T502FBT
CN003X-RAY
RESISTOR6.8K 0.5% 1/4W
1 2 3 4 5SERVICE CONNENTOR
TP-E
R561D561D562
C811R562
FR811 D812
B1TP-91
C562R565
X-RAY2
1 2 3 4 5
X-RAY1NC
TP-91140V
TP-E( )
124
16
28
2
3
1
710
9
5S1
CONNENTORS1
AV-65WP74
(No.52096)1-67
SECTION 4TROUBLESHOOTING
4.1 SELF CHECK FUNCTIONS• This model has self-check functions that inform of the failure of the TV by detecting abnormality.• Operational state is always monitored and the identified is memorized on the record.
4.1.1 HOW TO ENTER THE SELF-CHECK MODE(1) Set the <sleep timer 30min> with [SLEEP TIMER] key.
(Fig.1)(2) During the <sleep timer 30min> display, press [DISPLAY]
key and [VIDEO STATUS] key at the same time.(3) Then <TEST MODE> screen is displayed. (Fig.2)(4) Press [ 4 ] key then <SELF-CHECK> screen is appear.
(Fig.3)
4.1.2 HOW TO EXIT FROM THE SELF-CHECK MODE(1) By using the remote control unit, turn the power off. At this
time, the failure record is cleared.(2) Take off the AC plug from the wall outlet. At this time, the
failure record is not cleared.
4.1.3 SELF-CHECK DISPLAYThe self-check results are shown on the following display.Method of indication when the raster is not displayed (Fig.3).
Each failure is shown by turning POWER LED on and off atspecified intervals.
4.1.4 EXPLANATION FOR ACTIVATION OF SELF-CHECKFUNCTIONS
• For X-ray protection, B1 over-current protection and low Bshort protection, the power of the TV is turned off if NG is de-tected.Immediately after the power is turned off, POWER LED will beturning on and off.When the power is turned off, you cannot turn the power onagain until the AC plug is taken out and put in again.
• The latest failure is stored on the record at the end.The failure record for each check item is counted to the num-ber of 9 at the maximum, When more than 9 failures are storedon the record, the counter remains stopped at 9.
• SYNC is neither counted nor stored in memory.• Because of the timing of Vcc start-up and shut-down of the IC
connecting to the I2C bus during which the power is turned onand off, the operation may be interpreted as an error. In order to avoid the misinterpretation, the self-check functionsshould be started at about 3 seconds after the power is turnedon.
Fig.1
Fig.2
Fig.3 SELF-CHECK SCREEN
Item POWER LED ON / OFF intervalsX-ray protection Turning on and off 0.1-second intervalsB1 over-current protection
Turning on and off 1-second intervals
Low B short protection Turning on and off 2-second intervals
30MINSLEEP TIMER
1. I2C STOP2. STATUS DISP.
4. SELF-CHK5. CONVER OFF
TEST MODE
ROM CORRECTION : ACTROM VERSION :
XRAYLOBSYNCMEMVCDAIOTUNPP
NG2OKM:OKOKNG2OKOKNG4
OCPTIMS:OKAVSWBSYCGCRIP
NG2OKHD:NGOKOKOKOKOK
ITEM COUNTRESULT
AV-65WP74
1-68 (No.52096)
Indication Check item Details of detection Method of detectionXRAY X-ray radiation protection Operation of X-ray protection circuit.
D561, D562 : POWER & DEF PWBAt about 3 seconds after the power is turnedon, the self-check function starts. If NG isdetected for 200ms, the power is turned offautomatically.
OCP B1 over-current protection An B1 over-current is detected.Q971 : POWER & DEF PWB
At about 3 seconds after the power is turnedon, the self-check function starts. If NG isdetected for 200ms, the power is turned offautomatically.
LOB Low B short protection Operation of low B short protectioncircuit.Q1961(5V), Q1962(9V) : MAIN PWB
At about 3 seconds after the power is turnedon, the self-check function starts. If NG isdetected for 200ms, the power is turned offautomatically.
TIM Timer The AC power frequency is changedas follows : 50Hz ---> 60Hz 60Hz ---> 50Hz
Periodically check the power frequency bycounting the AC pulse and monitor whether ornot the frequency is changed except for thetime immediately after resetting.
SYNC Presence or absence of synchronized signal
Presence of synchronized signal.HD : HD signalM : NTSC main signalS : NTSC sub signalIC1301(AN5392) : MI-COM & DIST MODULE PWB
When entering the self-check mode, "OK" isshown.While running the mode with picture signal, ifthe synchronized signal is disappeared, "NG"is shown.
MEM Memory (EEP-ROM) ACK is returned when I2C traffic iscarried out.IC1703(MEMORY) : MI-COM & DIST MODULE PWB
The state is monitored every time when I2Ctraffic is carried out. Then the state is countedas a failure if ACK is not returned.
AVSW AV switch DittoIC1301(AN15852A) and IC1501(CXA2069Q) : MAIN PWB
Ditto
VCD Video / chroma process (RGB process)
DittoIC1301(AN5392) : MI-COM & DIST MODULE PWB
Ditto
BS Broadcast satellite tuner Not used Not usedAIO Audio process
The components identified by the symbol and shading arecritical for safety. For continued safety replace safety critical components only with manufactures recommended parts.
2.SPECIFIED VOLTAGE AND WAVEFORM VALUESThe voltage and waveform values have been measured under the following conditions.
(1)Input signal : Colour bar signal
(2)Setting positions of each knob/button and variable resistor
(3)Internal resistance of tester :DC 20k /V
(4)Oscilloscope sweeping time :H 20µS/div
:V 5mS/div
:Others Sweeping time is specified
(5)Voltage values :All DC voltage values
Since the voltage values of signal circuit vary to some extent according to adjustments, use them as reference values.
3.INDICATION OF PARTS SYMBOL [EXAMPLE]
In the PW board :R1209 R209
4.INDICATIONS ON THE CIRCUIT DIAGRAM(1)Resistors
Resistance value
No unit :[ ]
K :[K ]M
Rated allowable powerNo indication :1/ 16 [W]
Others :As specified
Type
No indication :Carbon resistorOMR :Oxide metal film resistorMFR :Metal film resistorMPR :Metal plate resistorUNFR :Uninflammable resistorFR :Fusible resistor
Composition resistor 1/2 [W] is specified as 1/2S or Comp.
(2)Capacitors
: Original setting position when shipped
5.NOTE FOR REPAIRING SERVICEThis model's power circuit is partly different in the GND. The difference of the GND is shown by the LIVE : ( ) side GND and the ISOLATED(NEUTRAL) : ( ) side GND.Therefore, care must be taken for the following points.
(1)Do not touch the LIVE side GND or the LIVE side GND and the ISOLATED(NEUTRAL) side GND simultaneously. If the above caution is not respected, an electric shock may be caused. Therefore, make sure that the power cord is surely removed from the receptacle when, for example, the chassis is pulled out.
(2)Do not short between the LIVE side GND and ISOLATED(NEUTRAL) side GND or never measure with a measuring apparatus measure with a measuring apparatus ( oscilloscope, etc.) the LIVE side GND and ISOLATED(NEUTRAL) side GND at the same time. If the above precaution is not respected , a fuse or any parts will be broken.
Since the circuit diagram is a standard one, the circuit and circuit constants may be subject to change for improvement without any notice.
NOTEDue improvement in performance, some part numbers show in the circuit diagram may not agree with those indicated in the part list.When ordering parts, please use the numbers that appear in the Parts List.
Type
MM :Metalized mylar capacitorPP :Polypropylene capacitorMPP :Metalized polypropylene capacitorMF :Metalized film capacitorTF :Thin film capacitorBP :Bipolar electrolytic capacitorTAN :Tantalum capacitor
(3)Coils
No unit :[ µH]
Others :As specified
(4)Power Supply
:B1
:9V :5V
Respective voltage values are indicated
(5)Test point
:Test point :Only test point display
(6)Connecting method
:Connector :Wrapping or soldering
:Receptacle
(7)Ground symbol
:LIVE side ground
:ISOLATED(NEUTRAL) side ground
:EARTH ground
:DIGITAL ground
:[M ]
Capacitance value
1 or higher :[pF]less than 1 :[µF]Withstand voltageNo indication :DC50[V]
Others :DC withstand voltage [V]
AC indicated :AC withstand voltage [V] Electrolytic Capacitors
47/50[Example]:Capacitance value [µF]/withstand voltage[V]
VOLTAGE (V)PIN NO. VOLTAGE (V)PIN NO. VOLTAGE (V)PIN NO. VOLTAGE (V)PIN NO. VOLTAGE (V)PIN NO. VOLTAGE (V)PIN NO. VOLTAGE (V)PIN NO. VOLTAGE (V)PIN NO. VOLTAGE (V)PIN NO. VOLTAGE (V)PIN NO. VOLTAGE (V)PIN NO.
R0117
R0574
R0562
L0102
R0101
R0109
CN0006
R0580
Q0101
R0534R0531
LC0101
R0532
C0230
R0212
R0561
IC0201
C0221
C0201
R0108
R0118
IC0701C0219
C0105
Q0102
C0533
D0701
C0701
R0704
R0110
R0705
R0106
TU0101
C0532
Q0103
R0542
IC0531 C0534
C0562
D0531
R0539
R0537
C0531
R0107
R0533
C0106
R0535
R0540
R0111
IC0531
R0538
CN0005
R0541
R0543
C0537
C0704
R0536
C0535
J0601
TU0102
C0206
R0565
R0563
R0567
C0208
UD0102
R0564
Q0532
C0561
Q0563
IC0561
Q0565
R0571
R0572
Q0564
D0563
R0579
R0701
R0112
C0203
Q0562
CN0701
R0569
R0568
R0573
R0570
D0561
R0575
R0607
R0505
R0504R0508
R0506
R0502
R0503
R0501
IC0501
R0507
C0502
C0504
C0207
R0208
R0577
C0212
C0211
C0228
C0501
UD0101
R0544
C0205
C0226
R0204
C0202
C0204
R0207
R0214
R0213
C0210
C0213
C0225
C0536
C0222
C0224
C0503
C0227
R0211
Y0561
R0578
C0104
R0576
R0206
Q0531
Y0562
Q0568
Q0566
Q0567
R0566
D0562
R0706
R0707
Y0001
Y0002
C0220
Q0702
C0223
Q0701
C0214
IC0501
C0209
R0205
R0606
R0605 R0610
R0609
R0608
R0602
R0601
R0604
R0603
Q0602
CN000S
Q0601
D0602
C0601
C0602
C0103
D0601
R0210R0209
CN000M
D0202
CN00S3
D0201
J0501
Q0561
C0217
C0702
C0703
C0231
CN0CC1
CN0CC2
R0217
CN00DC
R0218
D0203 D0204
CN00S4
C0218
IC0101
R0119
C0107 C0108
RY0601
RY0602
R0115
R0116
R0216
R0215
C0229L0201
W-E4
R07
03
R07
11
C02
15
R01
02
R07
09
R07
10
R01
05
R07
02
R01
04
R01
03
R01
13
R02
03
Y00
03
R02
02
C05
63
R02
01
C02
16
C01
02
R07
08
R01
14
QRN143J-0R0X
QGB1505K1-35
N
CXA2134Q-X
/50
/50
M62320FP-X
/50
/25
/25
/16
BA4558F-X
/50
MA8100/M/-X
/50
BA4558F-X
QGB1505K1-15
/50
CH
/25
CENTER
GND
CEMT019-001
QAU0303-001
/50
/50
QAU0283-001
/50
TC4066BP/N/
UN2212-X
/50
MA8100/M/-X
1/4W
BA4558F-X
/25
/50
/50
/50
/50N
/50
/50N
/25
/16
/50N
/50
/50
/50
/25
UN2212-X
MA8100/M/-X
/16PS
/16
BA4558F-X
/50
1/4W
2SC3311A/QR/-T
QGA2501C5-08
2SC3311A/QR/-T
/50QEZ0206-335Z
/50QEZ0206-335Z
/50
R_GND
R
L_GND
L
QJB003-043024
MA8082/M/-X
QGA2501F1-03
MA8082/M/-X
QNN0550-001
/50
/16PS
CH
N
GND
CENTER
12V
GND
CENTER
12V
GND
SCL2
SDA2
/50
L7805CP
/16 /16
QSK0133-001
QSK0133-001
NC
NC
NC
NC
NC
NC
N
N
SO
SC
L
SD
A
A/B
VA
RI/F
IX
NC
NC
GN
D
AG
CM
U2
AG
CM
U1
M-M
U
CE
NT
ER
VD
D
CS
2
CS
1
CS
0
NC
NC
NC
NC
NC
NC
N
N
N
/25
/50
N
N
N
/16
PS
N
N
N
GN
D
GN
D
5V
10K
6.8K
220
0
OPEN
10K
100K
*1
3.9K220
OPEN
82K
OPEN
OPEN
220
4.7
4.7
OPEN
27K
1
OPEN
*2
47
*3
47
3.3K
0
10K
10k
OPEN
.068
*1
10K
0.018
1
10K
15K
10
0
0
OPEN
3.3K
4.7K
0
10K
4.7K
10K
10
82p
10K
47
1
1.5K
82k
10K
10
82k
*2
1
*2
OPEN
OPEN
*1
*3
0
100
47K
4.7
*1
OPEN
10K
3.3K
22K
3.3K
5.6K
OPEN
12K
15K10K
10K
4.7K
15K
4.7K
12K
47
1
4.7
OPEN
0
4.7
4.7
0.0047
10
OPEN
10K
.012
4.7
100k
.1
.0056
62K
3.9k
3k
100
4.7
0.0047
10
4.7
0.022
1
0.1
3.3k
OPEN
OPEN
OPEN
OPEN
6.8k
*1
OPEN
OPEN
OPEN
1.5K
100K
10K
0
0
0.1
*2
0.1
*1
.0027
4.7
12K
0
0 OPEN
0
0
5.6K
4.7K
5.6K
4.7K
*3
3.3
3.3
10
*3
220220
*2
4.7
.1
82p
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN OPEN
OPEN
10
OPEN
100 100
OPEN
OPEN
OPEN
OPEN
OPENOPEN
OPEN
33K
100
.047
0
100
100
OP
EN
33k
OP
EN
OP
EN
220
1M
OP
EN
220
47
220
3.3
470 10
0
220
GND1
SDA0
BT30V
GND1
TU_5V/SW
GND1
GND2
GND1
GND1
GND1GND1
GND2
GND2
AFT2
GND1
GND1
GND1
GND1
GND1
GND1
GND2
GND1
GND1
GND2
GND1
GND1
GND1
GND1
GND1
SDA0
SCL0
GND1
SCL0
GND1
GND1
TV_V2
TV_V2GND
GND2
GND2
GND2
GND1
GND1
GND1GND1
GND1
GND1
GND1
GND1
GND1
GND1
GND1
GND1
GND2
TU_5V/SW
GND1
GND2
GND2
BT
30V
SD
A2
BS
_5V
TU
_5V
/SW
TU
_9V
/SW
SC
L0
SD
A0
TV
_V2G
ND
TV
_V2
AF
T2
SC
L2
SHEET 1
AUDIO IN
MAIN PWB
SPEAKERINPUT
SPEAKER
FOR TEST
MAIN PWB
SUBU/V FRONTEND
SHEET 11
-M2
AV-65WP74 AV-65WP74
No.52096 No.520962-33 2-34
R CRT SOCKET PWB CIRCUIT DIAGRAM SHEET 14
[H]
66Vp-p
[H]
66Vp-p
IC1101-9IC1101-7
VOLTAGE (V)PIN NO.
IC1101
1
2
3
4
5
6
7
8
9
2.9
11.6
2.9
0
7.0
211
179
181
178
IC1101
C1102
C1103C1101
C1104L1002
R1031
CN1RGK
R1032R1033
Q1031
R1109
R1103
R1106
L1102
D1103 R1105
R1101
R1102 C1105
C1108
R1110
R1104
CN1RGN
D1101
C1002
R1108
R1107
L1101
SG1001
D1001
R1005
C1007
R1006 R1008
C1005
TP-ER
Y1001
CN1RSC
CN10ER
H1101
D11
02
C11
06
C11
07
C10
06
CN
10R
E
TDA6111Q
/50
/25/50
QQL26AJ-102Z
R
GND
NC
12V
Vref
GND
QGA2501C5-06Z/50
3W
QJB003-042624
EU01N-T2
/250
QRC121K-561Z
QAF0056-501Z
RM2C-LFA1/250
QRC121K-102Z QRC121K-152ZQGZ0017C1-01Z
LC31150-002A
1SR
124-
400A
-T2
/250
QF
K62
EK
-104
Z
/50
HE
AT
ER
GN
D
NC
215V
QF
Z90
27-4
72
QG
Z50
03C
1-02
0.01
4710
OPEN
OPEN
OPENOPEN
OPEN
OPEN
820
0
BW
OPEN OPEN
680
2.2k 15p
OPEN
OPEN
47k
10
560
0
OPEN
1M
10
1K 1K
OPEN
BW
OPEN
0.1
560p
.004
7
GNDGND
GNDGND GND
GND
GND
GNDGND_DEF
GND
GND
QNZ0464-001
CRT SOCKETSK2001!
R CRT BC SAPICTURETUBE(R)
B CRT SOCKET PWBSHEET 16
G CRT SOCKETPWB
SHEET 15
R CRT SOCKET PWBSSB-3168A-M2
R
GNDHEATER
G1G2 G3
No.52096 No.52096
AV-65WP74AV-65WP74
2-35 2-36
G CRT SOCKET PWB CIRCUIT DIAGRAM SHEET 15
[H]
68Vp-p
[H]
68Vp-p
IC2101-7 IC2101-9
VOLTAGE (V)PIN NO.
IC2101
1
2
3
4
5
6
7
8
9
2.7
11.6
2.9
0
8.6
211
180
180.7
178
G CRT BC SAPICTURE TUBE(G)
IC2101
C2102
C2103
C2101
C2104
L2002
CN2RGNCN200V
CN200A
R2001
R2002
R2003
C2004
R2109
R2103
R2106
L2102
C2002
R2101
R2102 C2105
C2108
R2110
R2104
CN2GBN
D2101
R2108
R2107
L2101
SG2001
D2001
R2005
C2007
R2006R2008
C2005
CN20GE
TP-EG
Y2001
CN2GSC
Y2003
H2101
CN2GBKCN2RGK
Y2002
C2003
C2001
FR2007
Y2004
CN20EG
D21
02
C21
06
C21
07
L200
1
C20
06
TDA6111Q
/50
/25
/50
QQL26AJ-102Z
QGA2501C5-04ZQGA2501C5-03Z
HEATER
GND
NC
215V
QGA2501C5-04Z
0.5%
0.5%
0.5%
/250
/50
/503W
QGA2501C5-04Z
EU01N-T2
QRC121K-561Z
QQL244K-5R6Z
QAF0056-501Z
RM2C-LFA1/250
QRC121K-102Z
QNZ0464-001
QRC121K-152Z
QGZ5003C1-02
QGZ0017C1-01Z
GND
R
GND
B
GND
G
VM( GND)
VM
GND
GND
LC31150-002A
QGA2501C5-06ZQJB003-062211
/50
/250
1SR
124-
400-
T2
HE
AT
ER
GN
D
NC
215VVM
VM
( G
ND
)
12V
QF
K62
EK
-104
Z
/50
GN
D
NC
215V
HE
AT
ER
QQ
L26A
J-10
2Z
QF
Z90
27-4
72
GN
D
GN
D
NC
Vre
f
12V
R GN
D
GN
D
NC
12V
Vre
f
0.01
47
10
OPEN
12k
22k
4.7k
OPEN
OPEN
820
0
BW
10
680
3.3K 12p
4p
0
47k
560
10k
1M
10
1.5K 1K
OPEN
BW
OPEN
OPEN
0.022
10
OPEN
BW
OPEN
560p
GNDGND
GND
GND
GND
GND
GND
GND
GND
GND_DEF
GND
G1
G
G2 G3
CRT SOCKETSK2001!
GEND
HEATER
CN200EQGA2501C1-10
MI-COMDIST MODULE
PWB
VELOCITY MODULATION PWBSHEET 17
R CRT SOCKET PWBSHEET 14
R CRT SOCKET PWBSHEET 14
B CRT SOCKET PWBSHEET 16
B CRT SOCKET PWBSHEET 16
POWER & DEFPWB(2/2)
SHEET 20
G CRT SOCKET PWBSSB-3268A-M2
AV-65WP74 AV-65WP74
No.52096 No.520962-37 2-38
B CRT SOCKET PWB CIRCUIT DIAGRAM SHEET 16
[H]
60Vp-p
[H]
IC3101-9
60Vp-p
IC3101-7
VOLTAGE (V)PIN NO.
IC3101
1
2
3
4
5
6
7
8
9
Q3031
E
C
B
2.3
11.6
2.9
0
10.1
211
180
181
179
9
0
9
B CRT BC SAPICTURETUBE(B)
IC3101
C3102 C3103C3101
C3104
L3002
R3031
CN3GBK
R3032R3033
Q3031
R3109
R3103
R3106
L3102
D3103 R3105
R3101
R3102
C3105
C3108
R3110
R3104
CN3GBN
D3101
C3002
R3107
L3101
SG3001
D3001
R3005
C3007
R3006 R3008
C3005
CN30BETP-EB
Y3001
CN3BSC
CN30EB
H3101
C3109
D31
02
C31
06
C31
07
R31
08
C30
06
TDA6111Q
/50 /25/50QQL26AJ-102Z
0.5%
B
GND
NC
12V
Vref
GND
QJB003-062211
0.5%
2SA1037AK/QR/-X
MA111-X
/50
/50
3W
QJB003-042624
EU01N-T2
/250
QQL244K-5R6Z
QAF0056-501Z
RM2C-LFA1
/250
QRC121K-102Z QRC121K-152Z
QGZ5003C1-02
QGZ0017C1-01Z
LC31150-002A
/50
1SR
124-
400A
-T2
QF
K62
EK
-104
Z
/50
HE
AT
ER
GN
D
NC
215V
QR
C12
1K-5
61Z
QF
Z90
27-4
72
0.01 4710
OPEN
12k
5.6k100k
OPEN
820
0
BW
680
680
3.3k27p
10p
0
47k
10
10k
1M
10
1.5K 1K
OPEN
BWOPEN
27p
0.1
560p
560
.004
7
GNDGND
GNDGND GND
GND
GND
GND
GND_DEF
GND
GND
G1 G2 G3
QNZ0464-001
CRT SOCKETSK3001!
G
GEND
HEATER
G CRT SOCKET PWBSHEET 15
G CRT SOCKETPWB
SHEET 15
B CRT SOCKET PWBSSB-3368A-M2
No.52096 No.52096
AV-65WP74AV-65WP74
2-39 2-40
VM PWB CIRCUIT DIAGRAM SHEET 17
VOLTAGE (V)
1.1
6.0
1.7
5.3
11.7
6.0
130
66.4
127.2
2.7
66.4
3.2
PIN NO.
Q7101
E
C
B
Q7102
E
C
B
Q7105
E
C
B
Q7106
E
C
B
Q7105
Q7106
R7120
K7103
R7121
R7122
C7115
C7116
D7103
R7119
R7118 C7114
D7102
R7116
R7115
R7114
R7117
C7112
C7113
R7112
R7113
C7117
C7111
C7109
C7108
C7110
Q7102
K7104
R7123
R7107
R7106
C7119
K7101
K7102
Q7101
R7103
R7105
R7104
R7101
R7102
C7102
C7103
R7124
C7101
FR7001
C7104
C7105
Q7103R7108
R7109C7106
Q7104
R7111C7107
R7110
C7001
C7120
CN700J
CN700V
LC7101
Y7101
Y7102
H7102
H7101
C7002
CN7RAM
CN7GAM
CN7BAMC71
18
2SA1837
2SC4793
1/2W
CE41492-001Z
/10
/10
RH1S-T3
1/2W
/10
RH1S-T3
1/2W
1/2W
/500
/500
/160
2SC1627A/OY/-T
CE41492-001Z
2W
1W
CH
CE41492-001Z
2SD601A/QR/-X
CH
1W
FR
QRZ9021-561
/16
/160
CH
QGA2501C5-05Z
QJB003-031413
CEHP00N-001Q
CEHP00N-001Q
QGA2501C5-03Z
QGA2501C5-03Z
QGA2501C5-03Z
QS
C32
HJ-
151Z
2.7
39
120
100
330
2.7
39 100
56k
56k
1.2k
1.2k
0.0047
0.0047
47
47
10
OPEN
OPEN
OPEN
OPEN 100
68
1.5k
82pOPEN330
560
0
15k
2.7k
120p
OPEN
330
0.01
560
OPEN
100
OPEN OPEN
OPEN OPEN
OPEN
OPENOPEN
OPEN
10
68p
OPEN
0
0
OPEN
GNDGND
GND
GND
GND
GND
GND
GNDGND GND GND
GND
GNDGND GND
GND
GND
GND
GND
GND
GND
G CRT SOCKET PWBSHEET 15
POWER & DEFPWB(1/2)
SHEET 20
!
-M2
AV-65WP74 AV-65WP74
No.52096 No.520962-41 2-42
DEF OSC PWB CIRCUIT DIAGRAM SHEET 18
[V]
2.1Vp-p
IC101-18
9.8Vp-p
[H]
IC101-24
4Vp-p
[V]
IC101-30
2Vp-p
[V]
IC101-16
5Vp-p
[H]
IC101-16
4Vp-p
[V]
IC101-1
VOLTAGE (V)PIN NO. VOLTAGE (V)PIN NO.
IC101
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
IC102
1
2
3
IC161
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
IC162
1
2
3
4
5
6
7
8
IC163
1
2
3
IC212
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
Q101
E
C
B
Q102
E
C
B
Q131
E
C
B
Q132
E
C
B
Q162
E
C
B
Q167
E
C
B
Q168
E
C
B
Q751
E
C
B
Q752
E
C
B
Q753
E
C
B
4.6
0
1.3
7.2
0
8.1
5.2
0
0
6.4
5.7
0
8.2
0
8.3
1.8
NC
0.8
NC
7.1
11.6
5.9
0
0.1
0.1
0
1.7
5.8
5.3
5.6
11.9
0
13.7
4.1
4.1
0
4.9
8.8
NC
4.9
4.9
0
0
0
NC
0
0
11.6
4.8
4.8
3.6
0.6
2.8
8.0
2.5
1.1
6.1
11.6
3.3
0
0
1.8
1.2
1.7
0
2.3
0
0
11.6
11.6
0
4.9
0
0
3.2
3.3
0
NC
0.3
0
NC
NC
0
0
4.9
4.1
4.1
4.9
0
11.6
0.1
0
11.6
0.2
0.1
11.5
0.1
0
4.0
0
3.1
11.5
3.6
1.7
8.0
2.3
1.2
11.6
1.4
4.2
6.2
4.8
5.7
11.6
6.2
1.2
364
2.0
NC
H-B
LK_L
o
H-B
LK_H
i
V-B
LK_H
i
V-B
LK_L
o
CC
VC
C3
V-F
B
V-D
RIV
E
EW
CO
RN
ER
EH
T_A
EH
T_D
TR
AP
E_Z
OID
V-R
AM
P
V-A
GC
VC
C2
V.T
RI-
IN
A.G
ND
D.G
ND
IC101LA7860M-X
IC161
Q751
Q168
C131
Q131
Q101
Q102
R133
R143
R131
R134
R126
R139
R127
C136
C137
C135
C138
C122C121
C132
L101
C119
C120
IC102
IC163
C102
R114
R103
R102C101
R101
R105
R104
R106
R110C103
C104
C123
R107 R109
R108
C762
R113
R129 R112
R111
L104
C124
C106
C107
C108
C109
R116
C110
R117
C111C112
C113
C114C115
C117
C118
R121
R120
R122
R138L105
C172
C183
C116
C171
C184
C169
Y004
C173
C170
C168
C178
C179
C180
C181
C182
R187
R178
R177
R188
R180
R179
L103
R123
R184
R161R162
Q167
R167
R170
R171
R193
D171
C176
R321
R164
Q162
R176
C166R168
D165
R169
Y003
Y006
Y001
C167C174
R186
R190
IC162
R174
R182
R173
R172
D164
D166
R189
R181
C177
C162
C161
R175
CN00L
R191
Y002
R326
R327
R328
R329
D321
R330
D170
C321 R332
R183
R140
R141
C212
C221
R223 R224
R230
R227
R216R217
D221
Q753
IC212
Q752
C753
C763
R768
R751
R753
R767
R756
R752R755
R754 R757
R765 R764 R763 R762
C752
R142
Q132
C754
C165
C185C164
C163
R137
R163
R761
C751
Q754
Q755
R758
R759
Y007
Y008
R226
C175
Y005
R228
R229C222
D222
R195
R196R198
R197
Q171
Q172
D173 D174
C187
R199
Y009C
133
C13
4
R18
5
D75
1
D75
2
C76
1
AN5441SA-W
2SD601A/QR/-X
2SD601A/QR/-X
2SD601A/QR/-X
2SD601A/QR/-X
2SD601A/QR/-X
/16
QQL01BK-470Z
/25
/25
IN OUT
BA12FP-X
AN7805F
0.5%
0.5% 0.5%
0.5%
NQL092K-100X
0.5%
/16
QRG01GJ-470
QQL01BK-101Z
/50 TF/16
/16
/16
/16
/16
/160.5%
0.5%
0.5%
NQL092K-100X
QRK126J-101X
0.5%
2SD601A/QR/-X
1SS355-X
TF2SD601A/QR/-X
BA10393F-XE
1SS355-X
/16
QUB572-18PPFX
1SS355-X
1SS355-X
1SS355-X
2SC4632
CXA1875AM-X
2SD601A/QR/-X
QFZ0200-153
1/2W 1/2W 1/2W 1/2W
/35
2SD601A/QR/-X
/16
/10
1/2W
2SB709A/QR/-X
2SB709A/QR/-X
1SS355-X 1SS355-X
/50
V_S
YN
C
V_O
SC
V_O
SC
Ref
H_S
YN
C
EN
H_S
HIF
T
H_S
HIF
T
H_S
HIF
T
H_S
HIF
T
OU
T
AF
CP
ALS
E
GA
IN OS
C
OS
C
FIL
TE
R
RefV
/I
CO
NT
RO
LH H HH
HHG
ND
( H
)
NC
FB
P
LOC
K
DU
TY
Vcc
H
9V
AF
C
DE
LAY
DE
LAY
GA
IN
H
FB
PD
ELA
Y
VC
C12
V
HA
FC
SA
W
GN
D(
V)
VV
V
V
OU
T
BLK
SH
IFT
RA
NP
SD
A
SC
L
FB
P_I
N
VC
C1
TP
NC
H.A
GC
BLK
NE
CK
V-F
B
/25 /5
0
0.5%
GN
D
DE
F_R
ST
F/V
H_C
EN
T
OC
P
A0
A1
A2
SD
A
SC
L
VD
D
31/3
3
NC
NC
NC
NC
ES
1F-L
FG
2
ES
1F-L
FG
2
QF
Z01
22-6
82
100P150
470
1K
330K
10K
22K
10k
.001
.001
.001
180p
.01100
1
47
47
.01
2.2K
680
OPENOPEN
1K
47K
10K
12K
22K.01
560P
.01
10K 6.8K
OPEN
470p
12k
18K 1.8K
15K
.01
.001
.0012
4.7
.01
1.8K
.001
3.3K
2.22.2
.0012
.001.001
470
.01
1.5k
18K
47
OPEN
4.7
OPEN
.01
0.18
OPEN
.1
0
0.015
0.01
0.01
.1
.1
.1
.1
.1
4.7k
820
12k
100
1.5k
5.6k
100
47k
220220
10K
4.7k
22k
100
0.18
0
100
2.2k
104.7k
0
3.3k
0
OPEN
0
.0033.0027
10k
180
1k
1k
OPEN
47k OPEN
0
OPEN
OPEN
.01
1000
1k OPEN
0
220k
220k
56k
220k
68k
.001 OPEN
1k
10k
4.7k
10
1
100 100
22K
1K
220220
.015
470p
OPEN
18k
8.2k
OPEN
3.9K
10K18k
18k 1.5k
180K 180K 180K 180K
47
10k
BW
0.1
OPEN.01
470
10k
100
180K
.056
OPEN
OPEN
OPEN
OPEN
0
OPEN
100
.0015
OPEN
OPEN
OPENOPEN
OPEN
1K
22k10K
18K
.47
OPEN
OPEN.1
2 .015
10k
.006
8
DGND
DGND
DGND
DGND
DAF_SW
DGND
OSD_VD
EW
DGND
DGND
31/33
DGND
DGND
DGNDDGND
V_DRIVE
DGND
DGND
DAF_GND
DGND
DGND
DGND
DGND
A
OCP
H_DRIVE
DGND
DGND
DGND
DAF
DGND
DGND
A
DEF_HP
DGND
DGND
HB_PR0
DEF_RST
DGND DGND
EHT_DC DGND
ABL
DGND
DGND
DGND
DGND
FB
P
OC
P
DE
F_R
ST
SD
A
SC
L SD
A
SC
L
V_S
YN
C
5VDA
F_S
W
H_D
RIV
E
H_S
YN
C
EW
EH
T_D
C
31/3
3
12V
SC
L
SD
A
DE
F_H
P
12V
H_S
YN
C
V_S
YN
C
OS
D_V
D
V_D
RIV
E
FB
P
DA
F
H_S
YN
C
V_S
YN
C
EH
T_D
C
AB
L
5V
HB
_PR
0
20V
EH
T_F
BT
DA
F_G
ND
20V
EH
T_F
BT
CN010QGB1505K1-35CN0S4
QGA2501F1-03
POWER & DEF PWB(1/2)SHEET 19
DEF OSC PWB
DEF.OSC.
DISTORTION CORRECT
NOT USE
SHEET 4
-M2
No.52096 No.52096
AV-65WP74AV-65WP74
2-43 2-44
POWER & DEF PWB CIRCUIT DIAGRAM(1/2) SHEET19
[H]
T921-9
60Vp-p
[H]
T921-22
10Vp-p
[H]
T921-15
24Vp-p
[H]
T921-12
60Vp-p
[H]
T921-14
60Vp-p
[H]
T921-17
32Vp-p
VOLTAGE (V)PIN NO.
IC911
1
2
3
4
5
IC921
1
2
3
PC921
1
2
3
4
Q951
E
C
B
Q952
E
C
B
Q953
E
C
B
Q954
E
C
B
Q971
E
C
B
1.5
0
143.7
17.7
0
141.1
11.7
0
12.7
11.7
1.5
16.2
0
0
0.6
0
0.1
0.6
6.7
11.6
6.7
0
0
0.5
141.0
0
140.8
5V
K934
C904
C941
CP942
C931
14V
D954
D935
Y939
Y934
D938
K932
C973
K935
C994
OCP
Q952
B1_POW
H936
B1
Y940
Y902
R920 R956
H940
C918
CN00B
PROTECT
F932
C946
CN002
Y945
D937
C920
R903
C947
IC911
CN00P
D933
PC921
Y932
Y941
28V/10V
H938
D942
12V
L935F931
D974
R985
R983
Y933
CP941
C935
Y944
R901
R951
D955
Y955
L936
Y942R984
Y903
Q951
R908
Y952
D913
C995
D911
Q973
Y916
R914
F905
C913
C938
C919
CN001
D910
R910
D952
D917
K920
C910
R991
C936
R917
C921
R911
R947
R992
C908
F933
Y915
Y954
D934
K930
C934
C953
Y936
Y911
C944
C912
D916
R913
R902
C915
Y943
R999
R952
RY951
CP934
K914
D957
R918
R958
C954
D960
C901
Y953
Y909
L934
CP943
K937
D936
K938
D931
R961
Y951
R960
R944
R955
D956
C952
Y937
D959
Y935
R968
R963
R964
R941
R965
D941
Q953
R966Q954
C914R990
C922
D958
C942
R957
C937
R967
R962
L933
IC921
R959
L931
K931
Y914
R912
RY952
R948
C906
R954
R953
CP935
C932
C940
Y904
Y906
R916
K936
C993
Y901
C916
Y905
Y907
K933
LF901
C930
C902
C905
C943
R921
D932
C917
CP936
FR915
D953
D914
D912
D975
C907
Y910
R909
Q911 D919
D918
H901
D920
C999
K917
K916
K912
D915
C903
C939
CN00D
Y908
C997
C998
C945
D901
H911
T921
Y938
QCZ9054-102
CP
ICP-N70-T
QEZ0203-227
1SS133-T2
RU3YX-LFC4
FMX-G12S
/50
QQR0621-002Z
QCZ9074-472
2SC3311A/QR/-T
CM46960-00D
1/2W*
CEHT11B-002QS
QFV71HJ-104Z
B
QGA7901C1-02
/35
P
QGB1506M1-16
EU2-T3
QCZ0122-151
15WQRF154K-R51
STR-F6629B/F7
QJB003-102610
PC123FY2
QQL60AK-220
CP
ICP-N70-T
/35QETM1VM-228
15WQRF154K-R51
QQL26AK-220Z
2SC1627A/Y/-T
AU01Z-T2
QCZ9074-472
RGP10J-5025-T3
1/2W*QRK126J-681X
QMFZ034-5R0Z-J1
MY,5%
400VQFP32GJ-103Z
QGB1506M1-16
MA700A-T2
1/2W*
MTZJ12C-T2
MTZJ27B-T2
1/2W*
QRK126J-332X
2WOMR
QCZ9054-102
RU4AM-F1
QQR0621-002Z
/35QETM1VM-228
/16
2KVQCZ0340-332
1SS133-T2
2WMFR
1WMFRQRG01GJ-470
QRZ0111-685
QSK0118-001
CP
ICP-N70-T
QQR0582-001Z
1SS133-T2
1/2W*
/50
QQLZ018-220
CP
ICP-N20- Y
QQR0621-002Z
FMX-G12S
QQR0621-002Z
RU4AM-F1
1/2W*
QRT039J-1R
1SS133-T2
1SS133-T2
1/4W,1%
1/4W,1%
1/4W,1%
3WOMR
MTZJ33B-T2
2SC3311A/QR/-T
2SC3311A/QR/-T
/50
MTZJ6.8C-T2
/50
2kV
QCZ0340-152
QQL26AK-470Z
SE140N
1/2W
QQL26AK-470ZQQR0621-002Z
2WMFR
QSK0083-001
QSK0084-001
QCZ9054-102
1/2W*
1/2W*
CP
/25QETM1EM-228
2WMFR
QCZ9074-472
5%
5%
125VQFZ9072-104
QCZ9054-102
/16
RU30A-F 1
MY,5%
CPICP-N38-Y
1/2W
QRZ9017-330
1SS244-T2
1SS133-T2
AU01Z-T2
QEZ0572-128
MTZJ5.1B-T2
LC30171-001A
1SS133-T2
QCZ9074-472
QQR0582-001Z
SARS01-T2
D
QCZ9074-472
QCZ9074-472
/35
QETM1VM-228
RBV-606
LC31211-001A
QQS0133-001
BW
.001
OPEN
220P
BW
BW
BW
10
.0047
BW
OPEN
680k OPEN
.1
OPEN
1000
OPEN
150P
.51
OPEN
BW
BW OPEN
XOPEN
22OPEN
OPEN
OPEN
OPEN
BW
2200
OPEN
.51
47k
OPEN
OPEN
22
BWOPEN
BW
OPEN
OPEN
.0047
OPEN
OPEN
680470p
OPEN
.01
1.5k
OPEN
OPEN
OPEN
OPEN
3.3k
OPEN
18k
OPEN
OPEN
.001
OPEN
OPEN
OPEN
2200
OPEN
OPEN
BW
220
.0033
.18
47
OPEN
OPEN
6.8M
2.2k
1.5k
OPEN
22
OPEN
OPEN
BW
OPEN
2.2K
OPEN
47k
2.2k
OPEN
BW
OPEN
18k
4.7k
4.7k
33k
15k
47k
220OPEN
OPEN
1
OPEN
.0015
47k
4.7k
47
120
47
OPEN
.18
OPEN
.001
220
180
BW
2200
OPEN
BWBW
.22
BW
.0047
OPEN
330p
BW
OPEN
BW
OPEN
180p
.1
.001
470
OPEN
1800P
33
OPEN
1200
BW
OPEN
OPEN OPEN
.0047
BW
BW
OPEN
OPEN
OPEN
OPEN
.0047
.0047
2200
BW
GND1GND1
RELAY
GND1
GND3
GND1
GND1
GND1
GND1
B1
GND1
GND3
GND1
28V/10V
GND1
GND1GND1
GND1
M28V
GND1
GND1
GND1
14V
OCP
STBVCC
28V/10V
M28V
GND1
GND3
GND3
GND3
M7.5 V
BT
14V
AU_VCC
AU_GND
RELAY
STBVCC
28V/10V
GND1
M28V
GND1
GND3
12V
14V
M7.5V
GND1
PROTECT
GND1
B1_POW
GND1 GND1
5VGND3
GND1
GND1
GND1
GND3
GND3
GND3
GND3
BT
AU_VCC
GND3
AU_GND
GND1
GND1
PR
OT
EC
T
12V
OC
P
B1
28V
/10V
B1_
PO
W
14V
5V
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
! !
!
!
!
!
AC250V
AC250V
AC250V AC250V
AC250VAC250V
AC250V AC250V
AC250V
AC250V
Y2W
LINE FILTER PWBSHEET 21
POWER & DEF PWB(2/2)SHEET 20
MAIN PWBSHEET12
MAIN PWBSHEET12
CONVEREGENCEOUT PWBSHEET22
POWER & DEF PWBSSB-2068A-M2
AV-65WP74 AV-65WP74
No.52096 No.520962-45 2-46
POWER & DEF PWB CIRCUIT DIAGRAM(2/2) SHEET 20
IC401-3
[V]
100Vp-p
[H]
T502-4
140Vp-p
IC401-10
[V]
60Vp-p
[H]
T502-3
30Vp-p
IC401-9
[V]
30Vp-p
[H]
T502-8
350Vp-p
Q503-B
[H]
2Vp-p
[V]
[H]
T502-5
140Vp-p
IC401-4
60Vp-p
80Vp-p
Q501-D
[H]
[H]
T502-7
90Vp-p
[V]
IC401-6
0.35Vp-p
4.5Vp-p
Q501-G
[H]
[V]
IC401-8
30Vp-p
[H]
T502-10
1250Vp-p
[H]
T502-9
8Vp-p
Q503-C
[H]
1250Vp-pVOLTAGE (V)PIN NO.
IC401
1
2
3
4
5
6
7
8
9
10
Q401
E
C
B
Q402
E
C
B
Q503
E
C
B
Q521
E
C
B
Q532
E
C
B
Q533
E
C
B
Q501
S
D
G
Q531
S
D
G
0
-14.8
0.2
13.7
2.1
2.1
14.8
-13.5
14.2
-13.6
0
5.8
0
0.1
11.7
-1.5
0
213
0
1.5
11.7
1.7
9.7
11.7
9.6
9.6
0
9.7
0
32.2
1.7
0
21.8
9.7
C504
14V
Y502
B1_POW
OCP
D582
28V/10V
R407
B1
R972 R973
R975
R977 R978
C201
C971
C972
D973D972
CN00J
Q971
C501
R503
D501
R504C502
Q501
Y58
7
R502
H531
C401
R505
R501
L531
R522
R521
R531
Q521R523
R524R526
R506
C503
C526
C527
C523 C522 C521
C525
Y584
L504
CNGHV
C524
Y589
D522
D521
CNRHV
CNBHV
Q503
R525
D505
CN0AB
C506
D506
C507
C508
Y586
C511C510
QFZ0414-226
QFZ0128-254
250V MPP
C509
R591
L501
C404
R534
CN0AA
CN003
R412
R413
R420
R418
R416
D404
C409
C411
Q401
Q402
D405
R421 R401
R404
K502
R405
R406
R408
R402
L502
R403
C412 C413
C407
C406
D403
C417
R409
R410 R411
C408
C402
C405
C403
D402
K401
D401
R701
R702
R703
R206
T701C563
R432
CN00L
CN0S1
R201
R535
R202
C701
R203
FR803
C803
R536
D803
C802
CN00A
C416
R512
C534
R532
Q531
C514
R533
R419
D531
Y801
K503
K501
C513
Y503
C533
Q532
C536
K505
K504
R431
D504
R565C562
D562 D561
R430
R426
R561
R563
C414
C415
Y585
D406
Q581
L701
L801
C811
R562
Y581
Y582
R415
D201
D801
D802
D811
FR802
FR801
FR811
C801
Y701
C591
Q533
T502
H401
D583
PROTECT
Y504 Y505 Y506
Y588
12V
H503
R528
D524 C529
H506
C505
D507
Y501
Y403
Y402
Y401
5V
Y508
D407
IC401
D408
R422
C410
R428
R427
R424
R423
R425
R205
R204
D202
D581
T501
Y507
Y509
C812
1/4W,1%
1/4W,1 %
/2W*
1/2W*
TFQFV71HJ-334Z
/16
/25
MTZJ15B-T2
J
QGA2501C5-05Z
2SA1208/ST/Z1-T
/500
1/2W
1SS81-T5
3WOMR/200
D
GS
BSN304-T
1/2W
CEHT11B-005QS
/35
3WOMR
QQ
LZ03
6-22
2
2WQRL029J-102
/25
/200QFLC2AJ-682Z 2KV
QCZ0122-6812KV
QCZ0122-681
QQR0915-003
CHC802T-05N-J
1SS81-T5
MTZJ12C-T2
CHC802T-05N-J
CHC802T-05N-J
2SC5904-RL
QGZ8001C1-03
QFZ0122-452
FMV-3FU-F1
QFZ0122-452
630V
QFP32JJ-103
MPP400V
MPP400VQFZ0128-154
15WUNFQRF154K-3R3
QQLZ025-180
/200MY,5%
WJP0037-001A
QGB1506M1-16
MTZJ9.1B-T 2
/50
1/4W,1 % 1/4W,1%
1/4W,1%
1/4W,1 %
1/4W,1%
QQR1230-001
1/2W*
/16QENC1CM-226Z
/16QENC1CM-226Z
/5 0
/35/35
2WOMR
2WMFR
MY,5%
QFV71HJ-104Z
/5005%
1SR35-400A-T2
QQR0621-002Z
MTZJ75-T2QRG01GJ-220
1/2W
QRZ0056-103Z
QQR1096-001
1/2W
CE41507-001P
S1
QGA2501C5-05Z
/250RU30A-F1
/25
A
QGA2501C5-04Z
2WOMR
/200QFM72DK-222Z
2W
DG
S
IRFI620G
/500
2W QRL029J-820
RGP10J-5025-T3
QQR1139-001
/500
2SC1959/Y/-T
ABL
/200
QFM72DK-472Z
QQR1139-001
1/2W
RG2A-LFC4
/50QETN1HM-475Z
MTZJ7.5S-T2 MTZJ7.5S-T2
1/2W
1/4W,1 %
MTZJ6.8C-T2
QQLZ036-222
*
/35
1/4W,1 %
1SR35-400A-T2
EU2-T3
EU2-T3
1SR124-400A-T2
1/2W
!
1/2W
!
FR1/2W
QRZ9011-4R7
!
/25
QEZ0203-107
2SA562TM/Y/-T
!
LC31695-001A
LC31212-001B
QRG01GJ-152
GNDGND
LC30521-001A
V11CA-C1
1SR35-400A-T2
LA7876NZ
QQR1111-001
QCB32HK-821Z
OPEN
OPEN
OPEN
820
1.10k7.5K
22k
47k 33k
.33
100
47
*3
330p
1.5k
2.7k.01
OP
EN
12k
1000
2.7K
470
10K
10K
1k
*18.2k
6.8k47
5.6
.22
OPEN
47
.0068680P 680P
.0068
BW
47p
OPEN
1k
OPEN
.0045 .0045
.01
OPEN
.25.15
.15
3.3
18
.1
1k
4.7k
100k
100
2.2k
10k
10
.0022
*1
*1
*3
6.8K 5.6k
6.8k
OPEN
6.8k
4.7k
820
10k
200
18
2222
1
100
*3
100
220
2.2 OPEN
.1
.0015
.1
18P
22
12k
10k
OPEN
OPEN
100
180k
47
270k
.027
270k
OPEN
33
47
1000
6800P
330
.0022
82
560P
82
OPEN
BW
OPEN
22
OPEN
560P
.0022
OPEN
100
22k4.7
100
OPEN
4.7k
OPEN
OPEN
OPEN
BW
OPEN
100
5.6k
BW
OPEN
150k
*
*
4.7
1000
OPEN
100
*
*3
OPEN B
OPEN
1.5K
OPEN OPEN
OPEN
BW
OPEN
OPEN
BW
BW
OPEN
BW
OPEN
OPENBW
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
BWBW BW
BW
GND
GND
GND
GND
H_DRIVE
GND
GND
GND
GNDGND GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
20V
GND
GND
GND
GND
GND GND
FBP
GND
GND
GND
GND
DEF_HP
GND
EW
GND
GND
GND
GND
GND
GNDGND
GND
GND
GND
GND
GND
GND
GND
GND
20V
OS
D_V
D
SD
A0
SC
L0
DE
F_H
PH
_SY
NC
V_S
YN
C
SD
A0
EW
H_D
RIV
E
DE
F_H
P
SC
L0
H_S
YN
CV
_SY
NC
OS
D_V
D
FBP
CN010 QGB1505J1-35
1
DIVIDER
FORCUSPACK
R CRT
G CRT
B CRT
R CRT
G CRT
B CRT
VELOCITY MODULATION PWBSHEET 17
G CRT SOCKET PWBSHEET 15
MAIN PWBSHEET 10
DEF OSC PWBSHEET 18
POWER &DEFPWB(1/2)
SHEET 19
POWER &DEF PWBSSB-2068A-M2
SHEET 18
No.52096 No.52096
AV-65WP74AV-65WP74
2-47 2-48
LINE FILTER PWB CIRCUIT DIAGRAM SHEET 21
CN900WW
OPEN
BW
F9901
Y9903
VA9901
Y9912K9911
C9901
Y9904
CN90PW
D9913
D9921
D9912
D9914
Y9911C9921
R9911
C9903
C9902
CN90E1
R9901
D9911
CN90E2
Y9901
C9911
Y9902
T9911
Y9913
LF9903
LF9901 LF9902QMF61U1-7R0-S
ERZV10V621CS
QUY153-050Y
125V
QFZ9072-104
F
PW
QMPD390-200-JS
1SR35-400A-T2
1SR35-400A-T2
1SR35-400A-T2
1SR35-400A-T2
QETM1HM-108
1/2WQRE121J-5R6Y
B
125VQFZ9072-104
125VQFZ9072-104
E1
QRZ9041-275
1SR35-400A-T2
E2
16VQETN1CM-108Z
QQT0361-001
QQR1281-001
QQR0972-002 QQR0972-002
7A
OPEN
OPEN
0.1
OPEN
1000
5.6
0.1
0.1
OPEN
2.7M
OPEN
OPEN
1000
OPEN
OPEN
GNDGND
GND
GND
CN900BQGA7901C1-02
CN900FQGA2501C5-04Z
POWER & DEFPWB(1/2)SHEET19
MAIN PWBSHEET 12
! !
! !
!!
!
!
!
!
-M2
!
AV-65WP74 AV-65WP74
No.52096 No.520962-49 2-50
CONVERGENCE OUT PWB CIRCUIT DIAGRAM SHEET 22
CN0RI
CN0GI
D825
D817
D816R843
R842R840
C829
D819
D818R847
R846R844
C830
D824R859
R858R856
C833
D827
D826R863
R862R860
C834
CN0BI
D821
D820R851
R850R848
C831
D823
D822R855
R854R852
C832
IC805
H001
C819
C818
C825
C820
C823
R839
R834
R837
R803
R806
R805
IC804
C838
H003
C821
C824R838
R835
R802
R804
C822R836
R801
D804
D805
C827
C828
CN012
CN011
CN00Y
CN00P
L801
R811
Y801
C810C809
IC801
IC803
C813
C807 C808
C814C802
D841
D843D801
Y802
C801
CP801
CN00Z
K811
K808
K807
R830
R829
R828
Q808
Q807
Q806
R833
R832
R831
K806
K805K804
K803K802
K801
K810
D828
D839
C811
Q810
Q809
R867 R866
R864
R818
C812
K809
L802C804 C803
Q801
C806 C805
R813
C843
D842
R812 Q803
Q802
R810R808
R809
R807
R817
R865
H004
H005
IC806
C844
R869
Q812
Q811
R871
R870
R868
R872
D812
D811
C845
C846
D829 D830
C847
C848
C849
C850
D833 D834
D831 D832
R873
CYH+
CYH-
CYV+
CYV-
QGA2501C5-04Z
CYH+
CYH-
CYV+
CYV-
QGA2501C5-04Z
RD33E/B2/-T2
RD33E/B2/-T2
RD33E/B2/-T22WOMR
1WMFR
NDC31HJ-151X
RD33E/B2/-T2
RD33E/B2/-T2
2WOMR
1WMFR
NDC31HJ-151X
RD33E/B2/-T22WOMR
1WMFR
NDC31HJ-151X
RD33E/B2/-T2
RD33E/B2/-T2
2WOMR
1WMFR
NDC31HJ-151X
CYH+
CYH-
CYV+
CYV-
QGA2501C5-04Z
RD33E/B2/-T2
RD33E/B2/-T22WOMR
1WMFR
NDC31HJ-151X
RD33E/B2/-T2
RD33E/B2/-T2
2WOMR
1WMFR
NDC31HJ-151X
STK392-110
CEHT11B-002QS
NDC31HJ-151X
NDC31HJ-151X
NDC31HJ-151X
STK392-110
CEHT11B-002QS
NDC31HJ-151X
NDC31HJ-151X
NDC31HJ-151X
1SR153-400-T2
1SR153-400-T2
/50T
/50T
DIG.R
DIG.G
DIG.B
YS
5V
GND
-5V
BV
BH
GND
GND
GV
GH
RV
RH
QGB2501J1-15
GND
GND
GND
GND
GND
HOSTRXD
HOSTTXD
A.CONV.T
A.CONV.B
A.CONV.L
A.CONV.R
5VD
5VA
H_BLK
V_BLK
QGB2501J1-15
QJB003-114621
GND
GND
GND
GND
14V
-7.5V
-28V
-28V
28V
28V
QGA2501C1-10/25
/25
MY
L7805CP
L7805CP
/25MY
/16 /25
MY
/25
MY
/16
PTZ6.8B-X
PTZ6.8B-X/16
CP
A.CONV.T
A.CONV.B
A.CONV.L
A.CONV.R
GND
GND
GND
GND
QZA2501C5-08Z
QQR0621-002Z
QQR0621-002Z
QQR0621-002Z
2SD601A/QR/-X
2SD601A/QR/-X
2SD601A/QR/-X
QQR0621-002Z
QQR0621-002ZQQR0621-002Z
QQR0621-002ZQQR0621-002Z
QQR0621-002Z
QQR0621-002Z
NRSA63J-0R0X
NRSA63J-0R0X
2SD601A/QR/-X
2SD601A/QR/-X
NDC31HJ-181X
QQR0621-002Z
QQL521J-470 /25MY
/16T
2SC3852A
/25MY
/16T
PTZ6.8B-X
2SA673/C-T
2SA673/C-T
1/2W
LC31881-001A
LC31881-001A
TC7W04F-X
/16
T
D
GS 2SK1374-X
D
GS
2SK1374-X
PTZ8.2B-X
PTZ8.2B-X
NDC31HJ-470X
NDC31HJ-470X
MA111-X MA111-X
MA111-X MA111-X
2W0MR
CH
3OU
T
CH
3-V
CC
CH
3-IN
CH
3+IN
CH
2+IN
CH
2-V
CC
CH
2OU
T
VC
C
CH
1OU
T
CH
1-V
CC
CH
1-IN
CH
1+IN
PR
E+
VC
C
PR
E-V
CC
MU
TE
GN
D
SU
BG
ND
CH
2-IN
CH
3OU
T
CH
3-V
CC
CH
3-IN
CH
3+IN
CH
2+IN
CH
2-V
CC
CH
2OU
T
VC
C
CH
1OU
T
CH
1-V
CC
CH
1-IN
CH
1+IN
PR
E+
VC
C
PR
E-V
CC
MU
TE
GN
D
SU
BG
ND
CH
2-IN
DIG
.B
DIG
.G
DIG
.R
GN
D
GN
D
GN
D
YS
HS
VS
HO
ST
RX
D
HO
ST
TX
D
220
2.23.3k
150p
150
1.53.3k
150p
220
3.33.3k
150p
150
1.83.3k
150p
220
2.23.3k
150p
150
1.53.3k
150p
.01
.01
150p
150p
150p
47k
47k
47k
2.7k
2.7k
2.7k
.1
150p
150p47k
47k
2.7k
2.7k
150p47k
2.7k
470
470
OPEN
OPEN
BW
100.1
.1
100 .1
.1100OPEN
BW
100
BW
100
100
100
1k
1k
1k
OPEN
1k 1k
47k
47k
180p
47.1 100.1 100
1k
.01 1k
1.2k2.7k
470
2.7k
OPNE
OPEN
10
1k
1k
1k
10k
0
15p
15p
15P
15P
OPEN
OPEN
OPEN OPEN
220
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND GNDGNDGND
GND
GND
GND
GND GND GND GND
GND
GND
GND
GND
GND
GND
GND
GND
GNDGND
GND
GND GNDGNDGNDGND
GND
GND
GND
GND
GND
GND
GND GND
GND GND
GND GND
GND GND
R CONVERGENCEYOKE
G CONVERGENCEYOKE
B CONVERGENCEYOKE
MICOM & DIST MODULE PWB
POWER & DEFPWB(1/2)SHEET19
DIGITALCONVERGENCE
MODULEPWB
CONVERGENCE OUT PWBSSB-5068A-M2
VOLTAGE (V)PIN NO. VOLTAGE (V)PIN NO. VOLTAGE (V)PIN NO. VOLTAGE (V)PIN NO. VOLTAGE (V)PIN NO.
REMOTE CONTROL UNIT PARTS LIST (RM-C1200G-1H) ................................................................... 3-18PACKING .................................................................................................................................................. 3-19PACKING PARTS LIST ............................................................................................................................ 3-19
EXPLODED VIEW PARTS LIST - 1 Ref.No. Part No. Part Name Description Local
1 65WP74-SC-SA SCREEN ASSY 2 LC11508-001A-A BACK COVER 3 LC21219-001A-A BACK BOARD UPPER
4 QYSBSF4016Z TAP SCREW 4mm x 16mm(x13) 5 LC21217-001A-A MIRROR HOLDER TOP 6 LC21218-001A-A MIRROR HOLDER L 7 LC21218-002A-A MIRROR HOLDER R 8 QYSBSAG4018M TAP SCREW 4mm x 18mm(x2)
17 QYSBSFG4016M TAP SCREW 4mm x 16mm(x10) 18 QYSBSFG4016M TAP SCREW 4mm x 16mm(x4) 19 QYSBSF4012Z TAP SCREW 4mm x 12mm(x2) 20 QYSBSAG4018M TAP SCREW 4mm x 18mm 21 LC32192-001A-A CONNECTOR COVER 22 LC21217-002A-A MIRROR HOLDER BOTTOM 23 LC32173-001A-A GLASS MIRROR
24 LC32231-001A-A SP GRILL ASSY 25 LC11521-001A-A BODY 26 LC21220-001A-A BACK BOARD LOWER 27 LC31757-002A-A FRONT BOARD
28 QAS0113-001 SPEAKER (x2) 29 QAS0105-001 SPEAKER (x2) 30 QYSBSA4012M TAP SCREW 4mm x 12mm(x12) 31 LC32193-001A-A BC FITTING (x2) 32 CM22765-001-A COOLANT PAN
33 LC31139-001A-A RATING LABEL 34 LC41424-001A-A HDCP WARNING 35 QYSBSFG4020M TAP SCREW 4mm x 20mm(x4) 36 QYSBSAG4018M TAP SCREW 4mm x 18mm(x4) 37 QYSBSFG4016M TAP SCREW 4mm x 16mm(x4) 38 QYSBSF4010Z TAP SCREW 4mm x 10mm(x2) 39 QYSDSA4015Z SCREW 4mm x 15mm(x2) 40 QYSBSAG4018M TAP SCREW 4mm x 18mm(x8) 41 CM47752-006 BRAND MARK 42 QYSPSPD4020Z SCREW 4mm x 20mm(x8) 43 QYSBSF4012Z TAP SCREW 4mm x 12mm(x2)
9 LC31829-001C-A DOOR 10 QYSBSF3012M TAP SCREW 3mm x 12mm(x2) 11 QYSBSF3012M TAP SCREW 3mm x 12mm(x3) 12 LC31883-003A-A CONTROL PANEL 13 LC31749-001A-A LED LENS 14 LC31751-001B-A KNOB 15 PU60109 CATCHER 16 LC41237-001A RUBBER CATCH (x4)
48 QAE0005-001 HV DIVIDER 49 QYSBSBG3008Z TAP SCREW 3mm x 8mm
50 QAE0006-001 FOCUS PACK 51 LC20977-002A-A UNIT BRACKET R 52 LC20977-001A-A UNIT BRACKET L 53 LC31736-001A-A PJ LENS (x3) 54 QUQ212-1708CG FFC WIRE 55 QUQ212-1306CF FFC WIRE 56 QYSBSF4012Z TAP SCREW 4mm x 12mm(x3) 57 QYSBSF3012M TAP SCREW 3mm x 12mm(x2) 58 LC11249-001B-A CHASSIS BASE
59 LC11511-001A-A AV BOARD 60 QYSBSF3012M TAP SCREW 3mm x 12mm(x7)
61 QNZ0563-001 ANODE WIRE ASSY 62 LC20106-001D-A POWER CORD CLAMP
63 QAM0468-001 F CABLE 64 WJX0014-001A E-COAXIAL ASSY
65 R CRT BC SA R CRT ASSY 66 G CRT BC SA G CRT ASSY 67 B CRT BC SA B CRT ASSY
68 LC32292-001A-A BARRIER SHEET 69 QMPD200-200-JC POWER CORD(US/CA) 2m BLACK T502 QQH0113-002 FB TRANSF
1215
9
10
11
FRONT CONTROL PWB
16
16
1314
FRONT
3-4(No.52096)
AV-65WP74
FRONT
VM PWB (G only)
CRT SOCKET PWB (R/G/B)
LINE FILTER PWB
MAIN PWB
CONVERGENCE OUT PWB
DIGITAL CONVERGENCE MODULE
FRONT RELAY PWB
RECEIVER PWB
MI-COM & DISTMODULE PWB DEF OSC PWB
DEF & POWER PWB
DIGITAL INPUT
MODULE PWB
68
52
53
65
66
67
48
5455
61
59
60
69
57
62
636458
56
56
51
5049
T502
(No.52096)3-5
AV-65WP74
PRINTED WIRING BOARD PARTS LIST MAIN PW BOARD ASS’Y (SSB-1068A-M2)Ref No. Part No. Part Name Description Local
D1093 MA8082/M/-X Z DIODED1301 MA8100/M/-X Z DIODED1302 MA8100/M/-X Z DIODED1401 MA111-X SI DIODED1402 UDZS5.1B-X Z DIODED1403 MA111-X SI DIODED1595 MA8100/M/-X Z DIODED1596 MA8100/M/-X Z DIODED1598 MA8100/M/-X Z DIODED1599 MA8100/M/-X Z DIODED1662 MA3330/L/-X Z DIODED1663 MA3330/L/-X Z DIODED1667 MA111-X SI DIODED1668 MA111-X SI DIODED1669 MA111-X SI DIODED1702 MA111-X SI DIODED1703 MA111-X SI DIODED1704 MA8100/M/-X Z DIODED1705 MA8100/M/-X Z DIODED1801 1SR35-400A-T2 SI DIODED1802 MA111-X SI DIODED1803 MA111-X SI DIODED1891 MA8082/M/-X Z DIODE
D1892 MA8082/M/-X Z DIODED1893 MA8051/M/-X Z DIODED1894 MA8051/M/-X Z DIODED1941 RK34-LFC4 SB DIODED1942 D3S4M-F1P20 SB DIODED1943 RK34-LFC4 SB DIODED1945 MA111-X SI DIODED1946 MA111-X SI DIODED1962 MA3030/H/-X Z DIODED1964 MA111-X SI DIODED1965 MA111-X SI DIODED1967 PTZ6.8B-X Z DIODED1968 PTZ6.8B-X Z DIODED1969 PTZ11B-X Z DIODED1981 RK34-LFC4 SB DIODED1982 PTZ6.8B-X Z DIODED1991 MA111-X SI DIODED1993 MA111-X SI DIODED2101 MA8100/M/-X Z DIODED2121 MA8100/M/-X Z DIODED2201 MA8100/M/-X Z DIODED2204 MA8100/M/-X Z DIODED2205 MA8100/M/-X Z DIODED2206 MA8100/M/-X Z DIODED2207 MA8100/M/-X Z DIODED2209 MA8100/M/-X Z DIODED2210 MA8100/M/-X Z DIODED2212 MA8100/M/-X Z DIODED2213 MA8100/M/-X Z DIODED2214 MA8100/M/-X Z DIODED2215 MA8100/M/-X Z DIODED2216 MA8100/M/-X Z DIODED2217 MA8100/M/-X Z DIODED2218 MA8100/M/-X Z DIODED2219 MA8100/M/-X Z DIODED2220 MA8100/M/-X Z DIODED2401 MA8100/M/-X Z DIODED2402 MA8100/M/-X Z DIODED2403 MA8100/M/-X Z DIODED2404 MA8100/M/-X Z DIODED2406 MA8100/M/-X Z DIODED2421 MA8100/M/-X Z DIODED2422 MA8100/M/-X Z DIODE
C1102 QETN1CM-477Z E CAPACITOR 470uF 16V MC1103 QETN1HM-106Z E CAPACITOR 10uF 50V MC1111 NCB31HK-103X C CAPACITOR 0.01uF 50V KC1112 NCB31HK-103X C CAPACITOR 0.01uF 50V KC1113 NCB31HK-103X C CAPACITOR 0.01uF 50V KC1213 QETN1CM-107Z E CAPACITOR 100uF 16V MC1214 QETN1HM-225Z E CAPACITOR 2.2uF 50V MC1215 QFLC1HJ-103Z M CAPACITOR 0.01uF 50V JC1216 NCF11CZ-475X C CAPACITOR 4.7uF 16V ZC1218 NCB11CK-105X C CAPACITOR 1uF 16V KC1219 NCF11CZ-475X C CAPACITOR 4.7uF 16V ZC1233 NDC31HJ-180X C CAPACITOR 18pF 50V JC1301 QETN1CM-107Z E CAPACITOR 100uF 16V MC1302 QETN1CM-107Z E CAPACITOR 100uF 16V MC1303 QETN1CM-107Z E CAPACITOR 100uF 16V MC1304 NCB31CK-104X C CAPACITOR 0.1uF 16V KC1305 NCB31CK-104X C CAPACITOR 0.1uF 16V KC1306 NCB31CK-104X C CAPACITOR 0.1uF 16V KC1307 QETN1CM-106Z E CAPACITOR 10uF 16V MC1311 NCB11CK-105X C CAPACITOR 1uF 16V KC1312 NCB11CK-105X C CAPACITOR 1uF 16V KC1313 NCB11CK-105X C CAPACITOR 1uF 16V KC1314 NCB11CK-105X C CAPACITOR 1uF 16V KC1315 NCB11CK-105X C CAPACITOR 1uF 16V KC1318 NCB11CK-105X C CAPACITOR 1uF 16V KC1321 NCB11CK-105X C CAPACITOR 1uF 16V KC1322 NCB31HK-103X C CAPACITOR 0.01uF 50V KC1323 NCB31HK-103X C CAPACITOR 0.01uF 50V KC1324 NCB11CK-105X C CAPACITOR 1uF 16V KC1325 NCB11CK-105X C CAPACITOR 1uF 16V KC1326 NDC31HJ-101X C CAPACITOR 100pF 50V JC1327 NDC31HJ-101X C CAPACITOR 100pF 50V JC1328 NDC31HJ-101X C CAPACITOR 100pF 50V JC1329 NDC31HJ-100X C CAPACITOR 10pF 50V JC1331 NCB11CK-105X C CAPACITOR 1uF 16V KC1332 NCB31HK-103X C CAPACITOR 0.01uF 50V KC1333 NCB31HK-103X C CAPACITOR 0.01uF 50V KC1341 NCB11CK-105X C CAPACITOR 1uF 16V KC1342 NCB31HK-103X C CAPACITOR 0.01uF 50V KC1343 NCB31HK-103X C CAPACITOR 0.01uF 50V K
Ref No. Part No. Part Name Description Local
3-6(No.52096)
AV-65WP74
C1351 NCB31HK-103X C CAPACITOR 0.01uF 50V KC1352 NCB31HK-103X C CAPACITOR 0.01uF 50V KC1353 NCB31HK-103X C CAPACITOR 0.01uF 50V KC1354 NCB31HK-103X C CAPACITOR 0.01uF 50V KC1355 NCB31HK-103X C CAPACITOR 0.01uF 50V KC1356 NCB11CK-105X C CAPACITOR 1uF 16V KC1366 NCB11CK-105X C CAPACITOR 1uF 16V KC1368 NCB11CK-105X C CAPACITOR 1uF 16V KC1371 QETN1CM-336Z E CAPACITOR 33uF 16V MC1372 NCB31CK-104X C CAPACITOR 0.1uF 16V KC1381 QETN1CM-336Z E CAPACITOR 33uF 16V MC1382 NCB31CK-104X C CAPACITOR 0.1uF 16V KC1391 QETN1CM-336Z E CAPACITOR 33uF 16V MC1392 NCB31CK-104X C CAPACITOR 0.1uF 16V KC1403 QETN1AM-108Z E CAPACITOR 1000uF 10V MC1404 QETN1AM-108Z E CAPACITOR 1000uF 10V MC1405 QETN0JM-108Z E CAPACITOR 1000uF 6.3V MC1406 QETN1AM-108Z E CAPACITOR 1000uF 10V MC1409 QETN1HM-106Z E CAPACITOR 10uF 50V MC1410 NCB31CK-104X C CAPACITOR 0.1uF 16V KC1411 NCB31CK-104X C CAPACITOR 0.1uF 16V KC1412 QETN1CM-107Z E CAPACITOR 100uF 16V MC1415 NCB31HK-103X C CAPACITOR 0.01uF 50V KC1416 QETN1EM-476Z E CAPACITOR 47uF 25V MC1417 NCB31HK-103X C CAPACITOR 0.01uF 50V KC1418 QETN1EM-476Z E CAPACITOR 47uF 25V MC1421 QETN0JM-108Z E CAPACITOR 1000uF 6.3V MC1423 QETN1HM-476Z E CAPACITOR 47uF 50V MC1430 NCB31HK-103X C CAPACITOR 0.01uF 50V KC1431 NCB31HK-103X C CAPACITOR 0.01uF 50V KC1432 NCB31HK-103X C CAPACITOR 0.01uF 50V KC1433 NCB31HK-103X C CAPACITOR 0.01uF 50V KC1442 QETN1EM-476Z E CAPACITOR 47uF 25V MC1501 NCF31CZ-104X C CAPACITOR 0.1uF 16V ZC1502 QETN1EM-476Z E CAPACITOR 47uF 25V MC1505 QENC1HM-475Z BP E CAPACITOR 4.7uF 50V MC1510 QENC1CM-106Z BP E CAPACITOR 10uF 16V MC1519 QETN1EM-476Z E CAPACITOR 47uF 25V MC1531 NCB31CK-104X C CAPACITOR 0.1uF 16V KC1532 QETN1HM-226Z E CAPACITOR 22uF 50V MC1539 QENC1HM-475Z BP E CAPACITOR 4.7uF 50V MC1540 QETN1AM-107Z E CAPACITOR 100uF 10V MC1579 QETN1EM-476Z E CAPACITOR 47uF 25V MC1598 NCB11CK-225X C CAPACITOR 2.2uF 16V KC1599 NCB11CK-225X C CAPACITOR 2.2uF 16V KC1641 QENC1HM-106Z BP E CAPACITOR 10uF 50V MC1642 NCB31CK-473X C CAPACITOR 0.047uF 16V KC1643 NCB31CK-333X C CAPACITOR 0.033uF 16V KC1645 NCB31CK-104X C CAPACITOR 0.1uF 16V KC1646 QETN1EM-476Z E CAPACITOR 47uF 25V MC1647 QETN1HM-226Z E CAPACITOR 22uF 50V MC1648 QETN1HM-106Z E CAPACITOR 10uF 50V MC1651 QENC1HM-106Z BP E CAPACITOR 10uF 50V MC1652 NCB31CK-473X C CAPACITOR 0.047uF 16V KC1653 NCB31CK-333X C CAPACITOR 0.033uF 16V KC1663 NRSA63J-0R0X MG RESISTOR 0Ω 1/16W JC1665 NRSA63J-0R0X MG RESISTOR 0Ω 1/16W JC1667 QETN1HM-106Z E CAPACITOR 10uF 50V MC1668 NDC31HJ-101X C CAPACITOR 100pF 50V JC1669 NCB11CK-105X C CAPACITOR 1uF 16V KC1670 QETN1HM-106Z E CAPACITOR 10uF 50V MC1671 NDC31HJ-101X C CAPACITOR 100pF 50V JC1672 NCB11CK-105X C CAPACITOR 1uF 16V KC1673 QETN1HM-107Z E CAPACITOR 100uF 50V MC1674 QETM1HM-108 E CAPACITOR 1000uF 50V MC1675 QFV21HJ-124Z MF CAPACITOR 0.12uF 50V JC1676 QFV21HJ-124Z MF CAPACITOR 0.12uF 50V JC1677 QETN1EM-108Z E CAPACITOR 1000uF 25V MC1678 QETN1EM-108Z E CAPACITOR 1000uF 25V MC1679 QETN1HM-475Z E CAPACITOR 4.7uF 50V MC1680 QETN1HM-475Z E CAPACITOR 4.7uF 50V MC1696 QETN1HM-106Z E CAPACITOR 10uF 50V MC1697 QETN1EM-476Z E CAPACITOR 47uF 25V MC1702 NCB11CK-105X C CAPACITOR 1uF 16V KC1802 QETN1HM-106Z E CAPACITOR 10uF 50V MC1803 QETN1EM-476Z E CAPACITOR 47uF 25V MC1941 QETN1VM-108Z E CAPACITOR 1000uF 35V MC1942 QETN1CM-108Z E CAPACITOR 1000uF 16V MC1944 QETN1VM-108Z E CAPACITOR 1000uF 35V MC1945 QEZ0256-128 E CAPACITOR 1200uF 10V MC1947 QETN1CM-477Z E CAPACITOR 470uF 16V MC1948 QETN1CM-477Z E CAPACITOR 470uF 16V MC1949 QETN0JM-108Z E CAPACITOR 1000uF 6.3V MC1950 QETN0JM-108Z E CAPACITOR 1000uF 6.3V MC1951 QETN1VM-108Z E CAPACITOR 1000uF 35V MC1952 QETN1AM-108Z E CAPACITOR 1000uF 10V MC1953 QETN0JM-108Z E CAPACITOR 1000uF 6.3V M
Ref No. Part No. Part Name Description Local
C1954 QETN0JM-108Z E CAPACITOR 1000uF 6.3V MC1955 NCB31EK-104X C CAPACITOR 0.1uF 25V KC1961 QETN1HM-105Z E CAPACITOR 1uF 50V MC1981 QETN1CM-107Z E CAPACITOR 100uF 16V MC1984 QETN1VM-477Z E CAPACITOR 470uF 35V MC1985 QETN0JM-108Z E CAPACITOR 1000uF 6.3V MC1989 QETN1AM-108Z E CAPACITOR 1000uF 10V MC1991 QETN1EM-107Z E CAPACITOR 100uF 25V MC1992 QETN1CM-477Z E CAPACITOR 470uF 16V MC1994 NCB11CK-225X C CAPACITOR 2.2uF 16V KC1995 NCB11CK-225X C CAPACITOR 2.2uF 16V KC1996 NCB11CK-225X C CAPACITOR 2.2uF 16V KC2101 NCB11CK-105X C CAPACITOR 1uF 16V KC2102 NCB31HK-103X C CAPACITOR 0.01uF 50V KC2103 QETN1HM-106Z E CAPACITOR 10uF 50V MC2104 QETN1HM-106Z E CAPACITOR 10uF 50V MC2105 NCB11CK-225X C CAPACITOR 2.2uF 16V KC2106 NCB11CK-225X C CAPACITOR 2.2uF 16V KC2121 NCB11CK-105X C CAPACITOR 1uF 16V KC2123 NCB31HK-103X C CAPACITOR 0.01uF 50V KC2124 QETN1HM-106Z E CAPACITOR 10uF 50V MC2126 QETN1HM-106Z E CAPACITOR 10uF 50V MC2127 NCB11CK-225X C CAPACITOR 2.2uF 16V KC2128 NCB11CK-225X C CAPACITOR 2.2uF 16V KC2144 QETN1HM-106Z E CAPACITOR 10uF 50V MC2145 NCB11CK-225X C CAPACITOR 2.2uF 16V KC2146 NCB11CK-225X C CAPACITOR 2.2uF 16V KC2302 NCB11CK-105X C CAPACITOR 1uF 16V KC2303 NCB11CK-105X C CAPACITOR 1uF 16V KC2322 NCB11CK-105X C CAPACITOR 1uF 16V KC2323 NCB11CK-105X C CAPACITOR 1uF 16V KC2341 NCB11CK-105X C CAPACITOR 1uF 16V KC2342 NCB11CK-105X C CAPACITOR 1uF 16V KC2343 NCB11CK-105X C CAPACITOR 1uF 16V KC3001 QENC1AM-336Z BP E CAPACITOR 33uF 10V MC3002 NDC31HJ-151X C CAPACITOR 150pF 50V JC3003 NDC31HJ-121X C CAPACITOR 120pF 50V JC3004 NDC31HJ-150X C CAPACITOR 15pF 50V JC3005 NCF11CZ-475X C CAPACITOR 4.7uF 16V ZC3006 NCF31CZ-104X C CAPACITOR 0.1uF 16V ZC3007 NCB31AK-334X C CAPACITOR 0.33uF 10V KC3008 NDC31HJ-151X C CAPACITOR 150pF 50V JC3009 NDC31HJ-121X C CAPACITOR 120pF 50V JC3010 NDC31HJ-150X C CAPACITOR 15pF 50V JC3011 NCF11CZ-475X C CAPACITOR 4.7uF 16V ZC3012 NCF31CZ-104X C CAPACITOR 0.1uF 16V ZC3013 NCF31CZ-104X C CAPACITOR 0.1uF 16V ZC3014 QETN1CM-107Z E CAPACITOR 100uF 16V MC3015 NCF31CZ-104X C CAPACITOR 0.1uF 16V ZC3016 NCF31CZ-104X C CAPACITOR 0.1uF 16V ZC3017 QENC1HM-475Z BP E CAPACITOR 4.7uF 50V MC3018 NCF31CZ-104X C CAPACITOR 0.1uF 16V ZC3019 NCB31HK-103X C CAPACITOR 0.01uF 50V KC3020 NCB31HK-103X C CAPACITOR 0.01uF 50V KC3021 NCB31HK-103X C CAPACITOR 0.01uF 50V KC3022 NCF31CZ-104X C CAPACITOR 0.1uF 16V ZC3023 NCF31CZ-104X C CAPACITOR 0.1uF 16V ZC3024 NCF31CZ-104X C CAPACITOR 0.1uF 16V ZC3025 QETN1CM-106Z E CAPACITOR 10uF 16V MC3026 NCF31CZ-104X C CAPACITOR 0.1uF 16V ZC3027 NDC31HJ-7R0X C CAPACITOR 7pF 50V JC3028 NDC31HJ-7R0X C CAPACITOR 7pF 50V JC3029 NCF31CZ-104X C CAPACITOR 0.1uF 16V ZC3030 NCF31CZ-104X C CAPACITOR 0.1uF 16V ZC3031 NCF31CZ-104X C CAPACITOR 0.1uF 16V ZC3032 NDC31HJ-560X C CAPACITOR 56pF 50V JC3033 NDC31HJ-330X C CAPACITOR 33pF 50V JC3034 NDC31HJ-560X C CAPACITOR 56pF 50V JC3035 NDC31HJ-330X C CAPACITOR 33pF 50V JC3036 NCF31CZ-104X C CAPACITOR 0.1uF 16V ZC3037 NCF31CZ-104X C CAPACITOR 0.1uF 16V ZC3038 NCF31CZ-104X C CAPACITOR 0.1uF 16V ZC3039 NCF31CZ-104X C CAPACITOR 0.1uF 16V ZC3041 QETN1CM-106Z E CAPACITOR 10uF 16V MC3042 NCB31HK-472X C CAPACITOR 4700pF 50V KC3044 NCB31HK-472X C CAPACITOR 4700pF 50V KC3045 NCB31HK-472X C CAPACITOR 4700pF 50V KC3046 NCB31HK-472X C CAPACITOR 4700pF 50V KC3047 QETN1CM-106Z E CAPACITOR 10uF 16V MC3048 NCB31HK-472X C CAPACITOR 4700pF 50V KC3049 NCB31HK-472X C CAPACITOR 4700pF 50V KC3050 NCB31HK-472X C CAPACITOR 4700pF 50V KC3051 NCB31HK-472X C CAPACITOR 4700pF 50V KC3052 NCB31HK-472X C CAPACITOR 4700pF 50V KC3053 NCB31HK-472X C CAPACITOR 4700pF 50V KC3054 NCB31HK-472X C CAPACITOR 4700pF 50V KC3055 NCB31HK-472X C CAPACITOR 4700pF 50V K
Ref No. Part No. Part Name Description Local
(No.52096)3-7
AV-65WP74
C3056 NCB31HK-472X C CAPACITOR 4700pF 50V KC3057 QETN1CM-106Z E CAPACITOR 10uF 16V MC3058 NCF31CZ-104X C CAPACITOR 0.1uF 16V ZC3059 QETN1HM-105Z E CAPACITOR 1uF 50V MC3060 NCF31CZ-104X C CAPACITOR 0.1uF 16V ZC3061 QETN1HM-105Z E CAPACITOR 1uF 50V MC3062 NCF31CZ-104X C CAPACITOR 0.1uF 16V ZC3063 QETN1HM-105Z E CAPACITOR 1uF 50V MC3064 NCF31CZ-104X C CAPACITOR 0.1uF 16V ZC3065 QETN1CM-106Z E CAPACITOR 10uF 16V MC3066 NCF31CZ-104X C CAPACITOR 0.1uF 16V ZC3067 QETN1CM-476Z E CAPACITOR 47uF 16V MC3068 NCB31HK-103X C CAPACITOR 0.01uF 50V KC3069 QETN1CM-476Z E CAPACITOR 47uF 16V MC3070 NCB31HK-103X C CAPACITOR 0.01uF 50V KC3071 QETN1CM-476Z E CAPACITOR 47uF 16V MC3072 NCF31CZ-104X C CAPACITOR 0.1uF 16V ZC3077 NCB31AK-334X C CAPACITOR 0.33uF 10V KC3078 NCF31CZ-104X C CAPACITOR 0.1uF 16V ZC3079 NDC31HJ-470X C CAPACITOR 47pF 50V JC3080 QBTC1CK-106Z TA E CAPACITOR 10uF 16V KC3082 NDC31HJ-151X C CAPACITOR 150pF 50V JC3086 NCB31HK-152X C CAPACITOR 1500pF 50V KC3088 NDC31HJ-100X C CAPACITOR 10pF 50V JC3089 NDC31HJ-100X C CAPACITOR 10pF 50V JC3090 NDC31HJ-100X C CAPACITOR 10pF 50V JC3099 NCB31HK-472X C CAPACITOR 4700pF 50V KC3100 NCB31HK-472X C CAPACITOR 4700pF 50V KC3501 NCF31CZ-104X C CAPACITOR 0.1uF 16V ZC3502 NDC31HJ-101X C CAPACITOR 100pF 50V JC3503 NDC31HJ-121X C CAPACITOR 120pF 50V JC3504 NDC31HJ-150X C CAPACITOR 15pF 50V JC3506 NCF11CZ-475X C CAPACITOR 4.7uF 16V ZC3507 NCF31CZ-104X C CAPACITOR 0.1uF 16V ZC3508 NDC31HJ-101X C CAPACITOR 100pF 50V JC3509 NDC31HJ-121X C CAPACITOR 120pF 50V JC3510 NDC31HJ-150X C CAPACITOR 15pF 50V JC3512 NCF11CZ-475X C CAPACITOR 4.7uF 16V ZC3513 NCF31CZ-104X C CAPACITOR 0.1uF 16V ZC3514 NDC31HJ-101X C CAPACITOR 100pF 50V JC3515 NDC31HJ-121X C CAPACITOR 120pF 50V JC3516 NDC31HJ-150X C CAPACITOR 15pF 50V JC3518 NCF11CZ-475X C CAPACITOR 4.7uF 16V ZC3519 QENC1CM-336Z BP E CAPACITOR 33uF 16V MC3520 QENC1CM-336Z BP E CAPACITOR 33uF 16V MC3521 QENC1CM-336Z BP E CAPACITOR 33uF 16V MC6001 QENC1HM-106Z BP E CAPACITOR 10uF 50V MC6002 QENC1HM-106Z BP E CAPACITOR 10uF 50V MC6003 QETN1HM-106Z E CAPACITOR 10uF 50V MC6004 QETN1HM-106Z E CAPACITOR 10uF 50V MC6005 NCB31HK-472X C CAPACITOR 4700pF 50V KC6006 NCB31CK-273X C CAPACITOR 0.027uF 16V KC6007 QETN1HM-106Z E CAPACITOR 10uF 50V MC6008 QETN1HM-105Z E CAPACITOR 1uF 50V MC6009 QETN1CM-107Z E CAPACITOR 100uF 16V MC6010 QETN1HM-106Z E CAPACITOR 10uF 50V M
D201 1SR35-400A-T2 SI DIODED401 MTZJ75-T2 Z DIODED402 1SR35-400A-T2 SI DIODED403 1SS133-T2 SI DIODED404 MTZJ9.1B-T2 Z DIODED405 1SS133-T2 SI DIODED406 MTZJ6.8C-T2 Z DIODED407 1SR35-400A-T2 SI DIODED501 1SS81-T5 SI DIODED504 RG2A-LFC4 SI DIODED506 FMV-3FU-F1 SI DIODED507 V11CA-C1 SI DIODED521 MTZJ12C-T2 Z DIODED522 1SS81-T5 SI DIODED531 RGP10J-5025-T3 SI DIODED561 MTZJ7.5S-T2 Z DIODED562 MTZJ7.5S-T2 Z DIODED583 1SS133-T2 SI DIODED801 EU2-T3 SI DIODED802 EU2-T3 SI DIODED803 RU30A-F1 SI DIODED811 1SR124-400A-T2 SI DIODE
Ref No. Part No. Part Name Description Local
3-10(No.52096)
AV-65WP74
D901 RBV-606 BRIDGE DIODED910 MA700A-T2 SB DIODE
D911 RGP10J-5025-T3 SI DIODED912 AU01Z-T2 FR DIODED913 AU01Z-T2 FR DIODED914 1SS133-T2 SI DIODED915 SARS01-T2 SI DIODED916 1SS133-T2 SI DIODED917 MTZJ27B-T2 Z DIODED918 MTZJ5.1B-T2 Z DIODED920 1SS133-T2 SI DIODED931 RU4AM-F1 SI DIODED932 RU30A-F1 SI DIODED934 RU4AM-F1 SI DIODED935 RU3YX-LFC4 SI DIODED936 FMX-G12S SI DIODED937 EU2-T3 SI DIODED938 FMX-G12S SI DIODED941 MTZJ33B-T2 Z DIODED952 MTZJ12C-T2 Z DIODED953 1SS244-T2 SI DIODED954 1SS133-T2 SI DIODED956 1SS133-T2 SI DIODED958 MTZJ6.8C-T2 Z DIODED959 1SS133-T2 SI DIODED972 MTZJ15B-T2 Z DIODED973 1SS133-T2 SI DIODE
PC921 PC123FY2 PHOTO COUPLER
C201 QFV21HJ-334Z MF CAPACITOR 0.33uF 50V JC401 QETN1VM-108Z E CAPACITOR 1000uF 35V MC402 QFLC1HJ-152Z M CAPACITOR 1500pF 50V JC403 QCS32HJ-180Z C CAPACITOR 18pF 500V JC404 QFLC2AJ-104Z M CAPACITOR 0.1uF 100V JC405 QFV21HJ-104Z MF CAPACITOR 0.1uF 50V JC406 QETN1VM-107Z E CAPACITOR 100uF 35V MC407 QETN1HM-105Z E CAPACITOR 1uF 50V MC408 QFLC2AJ-104Z M CAPACITOR 0.1uF 100V JC409 QETN1HM-106Z E CAPACITOR 10uF 50V MC411 QCB31HK-222Z C CAPACITOR 2200pF 50V KC412 QENC1CM-226Z BP E CAPACITOR 22uF 16V MC413 QENC1CM-226Z BP E CAPACITOR 22uF 16V MC416 QCB31HK-682Z C CAPACITOR 6800pF 50V KC417 QETN1VM-107Z E CAPACITOR 100uF 35V MC501 QCB32HK-331Z C CAPACITOR 330pF 500V KC502 QFM72DK-103 M CAPACITOR 0.01uF 200V KC503 QFV21HJ-224Z MF CAPACITOR 0.22uF 50V J
C513 QEZ0414-226 BP E CAPACITOR 22uFC514 QCS32HJ-561 C CAPACITOR 560pF 500V JC521 QCZ0122-681 C CAPACITOR 680pF 2kV KC522 QCZ0122-681 C CAPACITOR 680pF 2kV KC523 QFLC2AJ-682Z M CAPACITOR 6800pF 100V JC524 QCS31HJ-470Z C CAPACITOR 47pF 50V JC525 QCB31HK-682Z C CAPACITOR 6800pF 50V KC527 QETN1EM-476Z E CAPACITOR 47uF 25V MC533 QCS32HJ-561 C CAPACITOR 560pF 500V JC534 QFM72DK-222Z M CAPACITOR 2200pF 200V KC536 QFM72DK-222Z M CAPACITOR 2200pF 200V KC562 QETN1HM-475Z E CAPACITOR 4.7uF 50V MC591 QEZ0203-107 E CAPACITOR 100uF 160V MC701 QFLC2AJ-273Z M CAPACITOR 0.027uF 100V JC801 QETN1EM-108Z E CAPACITOR 1000uF 25V MC802 QETN1EM-108Z E CAPACITOR 1000uF 25V MC803 QETM2EM-336 E CAPACITOR 33uF 250V MC811 QETN1VM-107Z E CAPACITOR 100uF 35V M
C902 QFZ9072-104 MM CAPACITOR 0.1uF AC250V KC904 QCZ9054-102 C CAPACITOR 1000pF AC250V ZC905 QCZ9054-102 C CAPACITOR 1000pF AC250V ZC906 QCZ9054-102 C CAPACITOR 1000pF AC250V Z
C907 QEZ0572-128 E CAPACITOR 1200uF 200V MC908 QCZ9054-102 C CAPACITOR 1000pF AC250V Z
C912 QCZ0340-332 C CAPACITOR 3300pF 2kV KC913 QFLC1HJ-471Z M CAPACITOR 470pF 50V JC914 QETN1HM-227Z E CAPACITOR 220uF 50V MC916 QCS31HJ-331Z C CAPACITOR 330pF 50V JC917 QFLC1HJ-182Z M CAPACITOR 1800pF 50V JC918 QFV41HJ-104Z MF CAPACITOR 0.1uF 50V JC919 QFP32GJ-103 PP CAPACITOR 0.01uF 400V JC920 QCZ0115-151Z C CAPACITOR 150pF 2kV KC930 QCS31HJ-181Z C CAPACITOR 180pF 50V J
Ref No. Part No. Part Name Description Local
C931 QEZ0203-227 E CAPACITOR 220uF 160V MC932 QETM1EM-228 E CAPACITOR 2200uF 25V MC934 QETM1VM-228 E CAPACITOR 2200uF 35V MC935 QETM1VM-228 E CAPACITOR 2200uF 35V MC937 QCZ0340-152 C CAPACITOR 1500pF 2kV KC942 QETN1HM-105Z E CAPACITOR 1uF 50V MC943 QETN1CM-477Z E CAPACITOR 470uF 16V MC944 QETN1CM-227Z E CAPACITOR 220uF 16V MC945 QETM1VM-228 E CAPACITOR 2200uF 35V MC946 QETN1VM-108Z E CAPACITOR 1000uF 35V MC954 QETN1HM-226Z E CAPACITOR 22uF 50V MC971 QETN1CM-107Z E CAPACITOR 100uF 16V MC972 QETN1EM-476Z E CAPACITOR 47uF 25V MC973 QETN1HM-106Z E CAPACITOR 10uF 50V M
C993 QCZ9074-472 C CAPACITOR 4700pF AC250V MC994 QCZ9074-472 C CAPACITOR 4700pF AC250V MC995 QCZ9074-472 C CAPACITOR 4700pF AC250V MC997 QCZ9074-472 C CAPACITOR 4700pF AC250V MC998 QCZ9074-472 C CAPACITOR 4700pF AC250V MC999 QCZ9074-472 C CAPACITOR 4700pF AC250V M
Q801 2SC3852A POW TRANSISTORQ802 2SA673/C/-T TRANSISTORQ803 2SA673/C/-T TRANSISTORQ806 2SD601A/QR/-X TRANSISTORQ807 2SD601A/QR/-X TRANSISTORQ808 2SD601A/QR/-X TRANSISTORQ809 2SD601A/QR/-X TRANSISTORQ810 2SD601A/QR/-X TRANSISTORQ811 2SK1374-X MOS FETQ812 2SK1374-X MOS FET
D804 1SR153-400-T2 FR DIODED805 1SR153-400-T2 FR DIODED811 PTZ8.2B-X Z DIODED812 PTZ8.2B-X Z DIODED816 RD33E/B2/-T2 Z DIODED817 RD33E/B2/-T2 Z DIODED818 RD33E/B2/-T2 Z DIODED819 RD33E/B2/-T2 Z DIODED820 RD33E/B2/-T2 Z DIODED821 RD33E/B2/-T2 Z DIODED822 RD33E/B2/-T2 Z DIODED823 RD33E/B2/-T2 Z DIODED824 RD33E/B2/-T2 Z DIODED825 RD33E/B2/-T2 Z DIODED826 RD33E/B2/-T2 Z DIODED827 RD33E/B2/-T2 Z DIODED828 NRSA63J-0R0X MG RESISTOR 0Ω 1/16W JD829 MA111-X SI DIODED830 MA111-X SI DIODED831 MA111-X SI DIODED832 MA111-X SI DIODED839 NRSA63J-0R0X MG RESISTOR 0Ω 1/16W JD841 PTZ6.8B-X Z DIODED842 PTZ6.8B-X Z DIODED843 PTZ6.8B-X Z DIODE
C801 QETN1CM-107Z E CAPACITOR 100uF 16V MC802 QETN1CM-107Z E CAPACITOR 100uF 16V MC803 QETN1CM-107Z E CAPACITOR 100uF 16V MC804 NCB31EK-104X C CAPACITOR 0.1uF 25V KC805 QETN1CM-107Z E CAPACITOR 100uF 16V MC806 NCB31EK-104X C CAPACITOR 0.1uF 25V KC807 QETN1CM-107Z E CAPACITOR 100uF 16V MC808 NCB31EK-104X C CAPACITOR 0.1uF 25V KC809 NCB31EK-104X C CAPACITOR 0.1uF 25V KC810 QETN1EM-107Z E CAPACITOR 100uF 25V MC812 NDC31HJ-181X C CAPACITOR 180pF 50V JC813 NCB31EK-104X C CAPACITOR 0.1uF 25V KC814 NCB31EK-104X C CAPACITOR 0.1uF 25V K
Ref No. Part No. Part Name Description Local
C818 NCB31HK-103X C CAPACITOR 0.01uF 50V KC819 NCB31HK-103X C CAPACITOR 0.01uF 50V KC820 NDC31HJ-151X C CAPACITOR 150pF 50V JC821 NDC31HJ-151X C CAPACITOR 150pF 50V JC822 NDC31HJ-151X C CAPACITOR 150pF 50V JC823 NDC31HJ-151X C CAPACITOR 150pF 50V JC824 NDC31HJ-151X C CAPACITOR 150pF 50V JC825 NDC31HJ-151X C CAPACITOR 150pF 50V JC827 QETN1HM-477Z E CAPACITOR 470uF 50V MC828 QETN1HM-477Z E CAPACITOR 470uF 50V MC829 NDC31HJ-151X C CAPACITOR 150pF 50V JC830 NDC31HJ-151X C CAPACITOR 150pF 50V JC831 NDC31HJ-151X C CAPACITOR 150pF 50V JC832 NDC31HJ-151X C CAPACITOR 150pF 50V JC833 NDC31HJ-151X C CAPACITOR 150pF 50V JC834 NDC31HJ-151X C CAPACITOR 150pF 50V JC838 NCB31HK-104X C CAPACITOR 0.1uF 50V KC843 NCB31HK-103X C CAPACITOR 0.01uF 50V KC844 QETN1CM-106Z E CAPACITOR 10uF 16V MC845 NDC31HJ-150X C CAPACITOR 15pF 50V JC846 NDC31HJ-150X C CAPACITOR 15pF 50V JC847 NDC31HJ-150X C CAPACITOR 15pF 50V JC848 NDC31HJ-150X C CAPACITOR 15pF 50V J
D164 1SS355-X SI DIODED165 NRSA63J-0R0X MG RESISTOR 0Ω 1/16W JD170 1SS355-X SI DIODED171 1SS355-X SI DIODED173 1SS355-X SI DIODED174 1SS355-X SI DIODED221 1SS355-X SI DIODED321 1SS355-X SI DIODED751 ES1F-LFG2 SI DIODED752 ES1F-LFG2 SI DIODE
C102 NCB31HK-103X C CAPACITOR 0.01uF 50V KC103 NCB31HK-103X C CAPACITOR 0.01uF 50V KC104 NDC31HJ-561X C CAPACITOR 560pF 50V JC106 NDC31HJ-102X C CAPACITOR 1000pF 50V JC107 NDC21HJ-122X C CAPACITOR 1200pF 50V JC108 QETN1HM-475Z E CAPACITOR 4.7uF 50V MC109 NCB31HK-103X C CAPACITOR 0.01uF 50V KC110 NCB31HK-102X C CAPACITOR 1000pF 50V KC111 QETN1HM-225Z E CAPACITOR 2.2uF 50V MC112 QETN1HM-225Z E CAPACITOR 2.2uF 50V MC113 NDC21HJ-122X C CAPACITOR 1200pF 50V JC114 NDC31HJ-102X C CAPACITOR 1000pF 50V JC115 NDC31HJ-102X C CAPACITOR 1000pF 50V JC116 NCB31HK-103X C CAPACITOR 0.01uF 50V KC117 QTMN1CM-477Z E CAPACITOR 470uF 16V MC118 NCB31HK-103X C CAPACITOR 0.01uF 50V KC119 QETN1EM-476Z E CAPACITOR 47uF 25V MC120 QETN1EM-476Z E CAPACITOR 47uF 25V MC121 QETN1CM-107Z E CAPACITOR 100uF 16V MC122 NCB31HK-103X C CAPACITOR 0.01uF 50V KC123 NCB31HK-103X C CAPACITOR 0.01uF 50V KC124 NCB31HK-103X C CAPACITOR 0.01uF 50V KC131 NDC31HJ-101X C CAPACITOR 100pF 50V JC132 QETN1HM-105Z E CAPACITOR 1uF 50V MC133 NCB21EK-124X C CAPACITOR 0.12uF 25V KC134 NCB31HK-153X C CAPACITOR 0.015uF 50V KC135 NDC31HJ-102X C CAPACITOR 1000pF 50V J
Ref No. Part No. Part Name Description Local
3-14(No.52096)
AV-65WP74
RECEIVER PW BOARD ASS’Y (SSB0R368A-M2)
C136 NDC31HJ-102X C CAPACITOR 1000pF 50V JC137 NDC31HJ-102X C CAPACITOR 1000pF 50V JC138 NDC31HJ-181X C CAPACITOR 180pF 50V JC161 QETN1CM-108Z E CAPACITOR 1000uF 16V MC162 NCB31HK-103X C CAPACITOR 0.01uF 50V KC163 QETN1AM-477Z E CAPACITOR 470uF 10V MC164 NCB31HK-103X C CAPACITOR 0.01uF 50V KC165 NCB31CK-104X C CAPACITOR 0.1uF 16V KC166 QETN1HM-106Z E CAPACITOR 10uF 50V MC167 NCB31HK-332X C CAPACITOR 3300pF 50V KC168 NCB31HK-103X C CAPACITOR 0.01uF 50V KC169 NCB31CK-104X C CAPACITOR 0.1uF 16V KC170 NCB31HK-103X C CAPACITOR 0.01uF 50V KC171 QFVF1HJ-184Z MF CAPACITOR 0.18uF 50V JC172 QETN1HM-475Z E CAPACITOR 4.7uF 50V MC173 NCB31HK-153X C CAPACITOR 0.015uF 50V KC174 NCB31HK-272X C CAPACITOR 2700pF 50V KC175 NCB31HK-152X C CAPACITOR 1500pF 50V KC176 QFVF1HJ-184Z MF CAPACITOR 0.18uF 50V JC178 NCB31CK-104X C CAPACITOR 0.1uF 16V KC179 NCB31CK-104X C CAPACITOR 0.1uF 16V KC180 NCB31CK-104X C CAPACITOR 0.1uF 16V KC181 NCB31CK-104X C CAPACITOR 0.1uF 16V KC182 NCB31CK-104X C CAPACITOR 0.1uF 16V KC187 QETN1HM-474Z E CAPACITOR 0.47uF 50V MC212 QETN1HM-106Z E CAPACITOR 10uF 50V MC221 QETN1HM-105Z E CAPACITOR 1uF 50V MC321 NCB31HK-102X C CAPACITOR 1000pF 50V KC751 QFLC1HJ-563Z M CAPACITOR 0.056uF 50V JC752 QETN1VM-476Z E CAPACITOR 47uF 35V MC753 QFZ0200-153 MPP CAPACITOR 0.015uF 1.5kV HC761 QFZ0122-682 MPP CAPACITOR 6800pF 1.8kV HC762 QCZ0122-471 C CAPACITOR 470pF 2kV KC763 QCZ0122-471 C CAPACITOR 470pF 2kV K
D0201 MA8082/M/-X Z DIODED0202 MA8082/M/-X Z DIODED0531 MA8100/M/-X Z DIODED0561 MA8100/M/-X Z DIODED0562 MA8100/M/-X Z DIODED0563 1SS355-X SI DIODED0601 1SS355-X SI DIODED0602 1SS355-X SI DIODED0701 1SS355-X SI DIODE
C0102 QETN1CM-477Z E CAPACITOR 470uF 16V MC0103 QETN1HM-106Z E CAPACITOR 10uF 50V MC0107 QETN1CM-107Z E CAPACITOR 100uF 16V MC0108 QETN1CM-107Z E CAPACITOR 100uF 16V MC0201 QENC1HM-475Z BP E CAPACITOR 4.7uF 50V MC0202 NCB31EK-104X C CAPACITOR 0.1uF 25V KC0203 QENC1HM-475Z BP E CAPACITOR 4.7uF 50V MC0204 NCB31HK-562X C CAPACITOR 5600pF 50V KC0205 NCB31HK-123X C CAPACITOR 0.012uF 50V KC0206 QETN1HM-105Z E CAPACITOR 1uF 50V MC0207 QETN1HM-475Z E CAPACITOR 4.7uF 50V MC0208 QETN1HM-106Z E CAPACITOR 10uF 50V MC0209 QETN1HM-475Z E CAPACITOR 4.7uF 50V MC0210 QETN1CM-107Z E CAPACITOR 100uF 16V MC0211 QENC1HM-475Z BP E CAPACITOR 4.7uF 50V MC0212 QETN1HM-475Z E CAPACITOR 4.7uF 50V MC0213 QENC1HM-475Z BP E CAPACITOR 4.7uF 50V MC0214 NCB31HK-272X C CAPACITOR 2700pF 50V KC0215 NCB31HK-473X C CAPACITOR 0.047uF 50V KC0216 QETN1HM-335Z E CAPACITOR 3.3uF 50V MC0217 QENC1HM-475Z BP E CAPACITOR 4.7uF 50V MC0218 QETN1HM-106Z E CAPACITOR 10uF 50V MC0219 QETN1HM-105Z E CAPACITOR 1uF 50V MC0220 NCF31CZ-104X C CAPACITOR 0.1uF 16V ZC0221 QENC1HM-475Z BP E CAPACITOR 4.7uF 50V MC0222 QENC1HM-475Z BP E CAPACITOR 4.7uF 50V MC0223 NCF31CZ-104X C CAPACITOR 0.1uF 16V ZC0224 NCB31HK-223X C CAPACITOR 0.022uF 50V KC0225 NCB31HK-472X C CAPACITOR 4700pF 50V KC0226 QENC1HM-475Z BP E CAPACITOR 4.7uF 50V MC0227 NCB31EK-104X C CAPACITOR 0.1uF 25V KC0228 NCB31HK-472X C CAPACITOR 4700pF 50V KC0501 QETN1HM-106Z E CAPACITOR 10uF 50V MC0502 QETN1EM-476Z E CAPACITOR 47uF 25V MC0503 QENC1HM-105Z BP E CAPACITOR 1uF 50V MC0504 QENC1HM-105Z BP E CAPACITOR 1uF 50V MC0531 QETN1HM-106Z E CAPACITOR 10uF 50V MC0532 NCB31CK-683X C CAPACITOR 0.068uF 16V KC0533 QETN1EM-476Z E CAPACITOR 47uF 25V MC0534 NCB31HK-183X C CAPACITOR 0.018uF 50V KC0535 QETN1EM-476Z E CAPACITOR 47uF 25V MC0536 QENC1HM-106Z BP E CAPACITOR 10uF 50V MC0537 QENC1HM-106Z BP E CAPACITOR 10uF 50V MC0561 QETN1HM-105Z E CAPACITOR 1uF 50V MC0562 QETN1HM-105Z E CAPACITOR 1uF 50V MC0563 QETN1EM-476Z E CAPACITOR 47uF 25V MC0601 QEZ0206-335Z BP E CAPACITOR 3.3uFC0602 QEZ0206-335Z BP E CAPACITOR 3.3uFC0701 QETN1EM-476Z E CAPACITOR 47uF 25V MC0702 NCF31CZ-104X C CAPACITOR 0.1uF 16V ZC0703 NDC31HJ-820X C CAPACITOR 82pF 50V JC0704 NDC31HJ-820X C CAPACITOR 82pF 50V J
D0402 UDZS10B-X Z DIODED0403 UDZS10B-X Z DIODED0404 UDZS10B-X Z DIODED0405 UDZS10B-X Z DIODED0406 UDZS10B-X Z DIODED0701 SELU5E20C LEDD0703 MA8068-X Z DIODED0704 MA8068-X Z DIODED0735 UDZS10B-X Z DIODE
C0442 QETN1HM-105Z E CAPACITOR 1uF 50V MC0443 QETN1HM-105Z E CAPACITOR 1uF 50V MC0444 QETN1HM-106Z E CAPACITOR 10uF 50V MC0445 QETN1HM-106Z E CAPACITOR 10uF 50V MC0446 QFLC1HJ-103Z M CAPACITOR 0.01uF 50V JC0711 QETN1CM-336Z E CAPACITOR 33uF 16V MC0712 NCB31CK-104X C CAPACITOR 0.1uF 16V KC0713 NCB31CK-104X C CAPACITOR 0.1uF 16V K
