KAPITELC.PDF

05.2

003

Christian Dalloz Holding Deutschland GmbH & Co. KG, D-95015 Hof, P.O.Box 16 46, Phone +49/92 81/83 02-0, Fax +49/92 81/36 26, [email protected]

Technical specifications are subject to change without notice.

C 1

Safety in Action Fall Protection Systems

For vertical applicationFor fixing onto existing ladders or climbingirons. Comes with joint plate. Mountingbrackets extra to order. Maximum mountingdistance: 1680 mm. Installation of bracket torail is carried out through the rectangular cutouts in the back of the guide-rail. Maximumsection length: 4480 mm.

Anodized aluminiumRail profile: 52 x 33 mmWeight: 1,2 kg per metrePart No. FS-SAL-

Galvanized steelRail profile: 50 x 32 mmWeight: 3,2 kg per metrePart No. FS-SST-

Stainless steel, pickledRail profile: 50 x 32 mmWeight: 3,2 kg per metrePart No. FS-SA4-

Guide-Rails: Vertical

Bending See page C 2.

05.2

003



C 2


Smallest radii for guide-rails, made of aluminium, galvanized/stainless steel, shown in mm:

Important information for planning:

Guide rail, Aluminium Part No. FS-SAL-Guide rail, Galvanized steel Part No. FS-SST-Guide rail, Stainless steel pickled Part No. FS-SA4-

Typ 1 Typ 2 Typ 3 Typ 4 Typ 5

The length of the bend depends on the bending radius and on the angle (type 1 + 2) and/or off-set (typed 3 - 5).

A = Bottom edge of ladder to salient point of structure

B = Of-set (mm)

C = Angle (max. 15 )

D = Bottom edge to centre of obstruction

E = Width of obstruction

F = Upper edge of ladder to off-set

G = Of-set (max. 260 mm)

05.2

003



C 3


Top End-Stop, spring activatedPrevents the fall arrester from either beinginserted incorrectly or accidentally slippingout of the guide-rail. For fitting to the very topof the rail system. Comes with all fixings.

Stainless steel, pickledWeight: 0,2 kg/eachPart No. 21050

Bottom End-Stop, spring activatedPrevents the fall arrester from either beinginserted incorrectly or accidentally slippingout of the guide-rail. For fitting to the verybeginning of the rail system. Comes with allfixings.


Rigid End-StopDoes not allow the fall arrester being taken outof the very top ladder section. Comes with allfixings.


Guide-Rails: VerticalEnd-Stops

05.2

003



C 4


ClampFor fixing onto the center rungs of existingladders, or climbing irons. Comes with allinstallation elements. Support structure mustbe checked for sufficient strength.

Weight: approx. 0,5 kg/each

For rung diameter up to 25 mmBolt dimension: M 12 x 70 mmGalvanized steelPart No. 10903

Stainless steel, pickledPart No. 14809

For rung diameter 26 up to 35 mmBolt dimension: M 12 x 80 mmGalvanized steelPart No. 14804








Guide-Rails: VerticalMounting Brackets

05.2

003



C 5


Shimto compensate for different heights of individualrungs. Clamping rail screw length must beadapted as necessary.

Galvanized steel

t = 5 mmWeight: 0,4 kg/eachPart No. 18861


Stainless steel, pickled





05.2

003



C 6


BracketUsed for fixing of guide-rails onto the side ofclimbing irons. Comes with all installationelements. For step irons of 20- 25 mmdiameter.

Galvanized steelWeight: 1,6 kg/eachPart No. 11319


ClampFor clamping guide-rails to flat iron sidemembers of already mounted ladders. Comeswith all installation elements.

Standard:Dimension "b" = max. 60 mmDimension "h" = max. 15 mm



Special version:when ordering please indicate dimension "h"and "b".

Weight: upon request

Galvanized steelPart No. 19091

Stainless steel, pickled upon request.


05.2

003



C 7


BracketFor fastening guide-rails onto a structure, e.g.between step irons. Comes with installationelements for fixing guide-rail to bracket.Support structure must be checked forsufficient strength.



BracketFor fixing guide-rails onto side-corner struts ofexisting ladders. Comes with all installationelements.



BracketFor clamping guide-rails to round iron sidemembers diameter 35 -70 mm of alreadymounted ladders. Comes with all installationelements.


05.2

003



C 8


Pivotable FootrestFor use on ladders with side-rails made of flatiron up to an iron width of 50 mm. To be usedin conjunction with clamp Part No. 11382 or16847 only. Comes with all installationelements.

Weight: 19 kg/each

Hinge on left sideGalvanized steelPart No. 21516

Hinge on right sideGalvanized steelPart No. 21520

Stainless steel, pickled upon request.

Footrest for ChimneysFor installation on climbing irons with diametermax. 20mm. Pivots laterally. Comes with allinstallation elements.



Guide-Rails: VerticalFootrests

05.2

003



C 9


Guide-Rails: VerticalFootrests

Folding FootrestUnfolds to allow unrestricted climber access.Complete with fixings. The distance betweenrungs shall be min. 300 mm.



Footrests for climbing paths with reinforce-ment upon request.

Folding FootrestUnfolds to allow unrestricted climber access.Complete with fixings. The distance betweenrungs shall be min. 240 mm.

Weight: 4,7 kg/eachGalvanized steelPart No. 15662


05.2

003



C 10


Guide-Rails: VerticalExit Section

Exit SectionUsed for secure removing/inserting the fallarrester from/into the guide-rail, e.g. onplatforms. Suitable for rung spacing of 250 -320 mm with max. rung diameter of 24 mm.Special sizes on request. In this case pleaseenclose sketch with ladder cross-section, seepage C 11. A single-way assembly aid is partof the scope of supply.



05.2

003



C 11


- Recommended installing height above platform: ca. 1.000 mm.

Guide-Rails: VerticalEngineering Advice for Exit Section

05.2

003



C 12


TurntableFor safe transfer from vertical to horizontal.Made of stainless steel plate and aluminiumrail section. Please specify the profile of thehorizontal and vertical guide-rail.

Weight: 2,6 kg/eachStainless steel, pickled

Bending radius horizontal guide rail> 1000 mmPart No. 11607

Bending radius horizontal guide rail< 1000 mmPart No. 20349

Cost for mounting turntablePart No. 16884

Guide-Rails: VerticalAccessories

Ho-Ver turn tableFor safe change of travel direction fromvertical to horizontal to vertical travel. Thedirection of travel can only be changed to theleft or to the right. Consult Soll technicalsupport department for other installationcombinations.

Weight: 5,0kg per 1 unit

Stainless steel 1.4571, pickledPart No.22322

05.2

003



C 13


Mounting bracket with adjustableprojectionProjection: 120 mm up to 160 mm. Comeswith all installation elements.To be used formounting turntable Part No. 11607 only.



Guide Rails: VerticalAccessories

Mounting bracket with adjustableprojectionProjection: 160 mm up to 200 mm. Comeswith all installation elements.To be used formounting turntable Part No. 11607 only.



05.2

003



C 14


Reinforcement/StrengtheningIs required, when the distance between lastmounting point and top-end of the rail exceeds380 mm. It must be bolted onto the guide-railat a distance of 560 mm and must extenddown over at least two mounting brackets.Square tube 50 x 30 x 3 mm or 50 x 50 x 4mm. Comes with all installation elements.

Galvanized steelWeight: 3,3 kg per metrePart No. HV-ST-

Stainless steel, pickledWeight: 3,3 kg per metrePart No. HV-A4-

Anodized aluminiumWeight: 1,9 kg per metrePart No. HV-AL-

Anodizedaluminium

Galvanized steelStainless steel,pickled


05.2

003



C 15



Shaft Entering DeviceFor safe entry into manholes. The device isinserted into the female coupling on the top ofthe guide-rail in the manhole. This device canbe moved from one manhole ladder to another.


Female Coupling for Shaft Entering DeviceThis device is fixed to the top of the guide-railin the manhole.


Date post:	02-Oct-2015
Category:	Documents
Upload:	cokiaa
View:	212 times
Download:	0 times

KAPITELC.PDF

Documents