Date post: | 16-Apr-2017 |
Category: |
Technology |
Upload: | pt-tridinamika-jaya-instrument |
View: | 727 times |
Download: | 0 times |
© Aeroqual Ltd, 2011 Aeroqual Limited All rights reserved www.aeroqual.com March 2011
UV-1 UV Ozone Photometer OEM Module Description The Aeroqual UV-1 Ozone Photometer Module is designed for measurement and control of ozone in the range 0-200 ppm using a single beam UV photometer. It has a folded metal enclosure designed to be built into an ozone treatment system. The UV- 1 offers advanced monitoring and control.
Features • Wide measurement range (0-200 ppm) • Single-beam UV photometer • Pump sampling via PTFE tubing (e.g. monitoring outside of a room or duct) • Digital RS485 output (2 wire) or RS232 • Custom configuration upon request
Specifications Range 0-200 ppm Ozone Precision <±5% of reading above 0.2 ppm
±0.01 ppm below 0.2 ppm Resolution 0.01 ppm T90 <60s Sampling method Brushless DC diaphragm pump Sample flow rate 0.4 ±0.05 LPM Inlet filter 5 µm pore size, 37 mm PTFE filter Pneumatic connections Kynar 6.25mm (¼” ) compression fittings Wetted Materials Kynar, Teflon PFA, quartz, aluminium, viton Environmental operating conditions Temperature RH
0-40°C 0-95% RH (non-condensating)
Power requirements 24VDC, 2A Digital interface RS485 (2 wire), RS232 (Communication protocol supplied) Connectors Screw Enclosure Folded Aluminium
280 x 120 x 90 mm Software RS232 datalogging software supplied Options 0-5 V analog output, 12 bit
Accessories (optional) 24VDC DIN rail mount 100-250V AC (R35) Spare inlet filters (25 pack) (R12) RS485 to USB converter (R53) 10m x 6.25mm OD PFA tubing (R66)
Indicative picture of UV-1
© Aeroqual Ltd, 2009 Aeroqual Limited
All rights reserved www.aeroqual.com November 2009
Series 900 | 905 Gas Transmitter & Controller
Features • Active sampling for higher accuracy
• Multiple analog & digital outputs
• Real-time network capability
• Interchangeable sensor heads
• PC data logging & networking option
• Temperature & RH sensor (Series 905)
Applications • Ozone generator control applications
• Ambient & monitoring and control
• Real-time network monitoring
• Indoor air quality monitoring
• Health & safety
Specifications
Ozone Sensor Heads (other gases available)
Sensor Head
Calibrated Range
Maximum Exposure
Lowest Detection
Accuracy of Calibration
Resolution Response Time (T90)
Operating Conditions
OZU 0-0.15ppm 0.25ppm 0.001ppm <±0.005 ppm 0.001ppm < 70 s
OZL 0-0.5ppm 1ppm 0.001ppm <±0.008 ppm 0- 0.1ppm
<±10% 0.1-0.5 ppm 0.001ppm < 60 s
OZG 0-10ppm 15ppm 0.01ppm <±0.1 ppm 0-1 ppm <±15% 1-10 ppm
0.01ppm < 60 s
Temperature -5°C to 40°C
Humidity 5 to 95% RH (non-condensing)
Power (user supplied) Regulated 12V DC, 800mA
Analogue output 4-20mA (opto-isolated), 10-30V
External signal type Transistor outputs (4)
External signal functions Low Alarm, High Alarm, Control and Diagnostics
Inputs Standby toggle
Communication RS485 (Aeroqual proprietary protocol)
Jumpers J1, J2, J3 termination resistors
Connectors Screw
ID 1 (Default) - User configurable from 1 to 255
Alarm set points (2) User configurable
Control set point User configurable
Removable / replaceable / refurbish-able sensor head Yes
Sampling method Active sampling via internal sensor fan
Temperature & Humidity sensor (Series 905) Range -40°C to 124°C (-40°F to 255°F) | Range 0 to 100% RH
Configuration software (standard) PC Configuration Program CD (supplied)
Data logging & networking software (optional) PC Data Logging & Networking CD (code: R60)
USB interface (optional) RS485 to USB converter (code: R53)
Power supply (optional) 12V DC DIN rail mount 100-250V AC (code: R37)
Enclosure casing & rating Polycarbonate; IP20 & NEMA 1 equivalent
Enclosure size (with base unit) 64 x 130 Ø (mm); 2½ x 5⅛ Ø (in)
Mounting Screw fixture
Weight < 200 g; < 7 oz
Approvals Part 15 of FCC Rules EN 50082-1: 1997 EN 50081-1: 1992
© Aeroqual Ltd, 2013 Aeroqual Limited MRK-D-0003 V1
All rights reserved www.aeroqual.com
AQM60
Air Quality Monitoring Station
Accurate real-time air quality information,
made affordable.
For those needing to measure and manage common outdoor air pollutants, the AQM60 enables near-analyser levels of performance at a fraction of the cost of traditional reference monitoring stations.
The AQM60 is a totally configurable instrument platform able to measure common air pollutants including ozone (O3), nitrogen dioxide (NO2), nitrogen oxides (NOX), carbon monoxide (CO), sulphur dioxide (SO2), volatile organic compounds (VOC), hydrogen sulphide (H2S), non-methane hydrocarbons (NMHC), carbon dioxide (CO2), particulate matter (TSP, PM10, PM2.5, PM1), noise and meteorological parameters such as temperature, humidity, wind speed and direction.
Key Features
• Continuous measurement of common air pollutants
• Information available in real-time
• Compact and light enough to be carried by one person
• Quick and easy to install and relocate
• Flexible integration of meteorological and noise sensors
• On-board data-logging and remote data retrieval
• Gas modules allow for ease of maintenance
• Robust, temperature-controlled enclosure
• Automated calibration optional
• Calibrated against USEPA (40 CFR Part 53) and EU (2008/50/EC) certified equivalent method instruments
Applications
• Urban air quality monitoring
• Perimeter: petrochemical, power plants, waste sites, industrial point sources
• Airport, ports, railways, construction sites
• Short term monitoring of ‘hot spots’
• Community exposure: epidemiological studies, microenvironment, residential, schools, hospitals
• Near road: motorways, street canyons, traffic information systems
• Environmental impact assessments
Selected Customers
• Dubai Municipality, UAE
• Vale, Brazil
• URS Corporation, Australia
• Repsol YPF, Argentina
• Directorate General of Traffic, Spain
• Saudi Electricity Company, Saudi Arabia
• Cape Town City, South Africa
• Bengkalis Municipality, Indonesia
• Qingdao Government, China
© Aeroqual Ltd, 2013 Aeroqual Limited MRK-D-0003 V1
All rights reserved www.aeroqual.com
AQM60 Specifications
Typical configuration: 1 to 6 gas modules, particle monitor, weather sensor and auto-calibration system.
Gas Modules Range Minimum
Detection Limit Accuracy of
Factory Calibration Precision Resolution
Ozone O3 (GSS) 0-0.5 ppm 0.001 ppm <±0.008ppm 0 to 0.1 ppm;
<±10% of reading above 0.1 ppm 0.005 ppm 0.001 ppm
Nitrogen Dioxide NO2 (GSS) 0-0.2 ppm 0.001 ppm <±0.01 ppm 0 to 0.1 ppm;
<±10% of reading above 0.1 ppm 0.005 ppm 0.001 ppm
Nitrogen Oxides NOx (GSS) 0-0.5 ppm 0.001 ppm <±0.01 ppm 0 to 0.1 ppm;
<±10% of reading above 0.1 ppm 0.005 ppm 0.001 ppm
Carbon Monoxide CO (GSE) 0-25 ppm <0.04 ppm <±0.1ppm, 0 to 1 ppm
<±10% of reading above 1 ppm 0.1 ppm 0.01 ppm
Carbon Dioxide CO2 (NDIR) 0-2000 ppm <10 ppm <±(10 ppm + 5% of reading) 10 ppm 1 ppm
Hydrogen Sulphide H2S (GSE) 0-10 ppm <0.03 ppm <±0.05ppm 0 to 0.5 ppm
<±10% of reading above 0.5ppm 0.03 ppm 0.01 ppm
Sulphur Dioxide SO2 (GSE) 0-10 ppm <0.03 ppm <±0.05ppm 0 to 0.5 ppm
<±10% of reading above 0.5 ppm 0.05 ppm 0.01 ppm
Volatile Organic Compounds (PID) 0-20 ppm 0.01 ppm <±0.02ppm 0 to 0.2 ppm
<±10% of reading above 0.2 ppm 0.03 ppm 0.01 ppm
Non-methane Hydrocarbon (GSS) 0-25 ppm <0.1 ppm <±0.1ppm, 0 to 1 ppm
<±10% of reading above 1 ppm 0.1 ppm 0.01 ppm
Particle Monitor (nephelometer) Sizes
PM1 PM2.5 or PM10
Range
0-2000 µg/m3
Accuracy
<±(2 µg/m3 + 5% of reading)
Flow rate
2.0 LPM
Resolution
0.01 µg/m3
Particle Profiler (OPC) Sizes
PM1 PM2.5 and PM10
Range
0-500 µg/m3
Accuracy
<±(5 µg/m3 +
15% of reading)
Flow rate
1.0 LPM
Resolution
0.01 µg/m3
Control Module
Communication
RS 232
Data Storage
2 GB SD card
Data- logging Interval
2 to 255 minutes
Display
VFD 4 x 20
Status
Event Log
Gas Treatment Module
Sampling Pump
12V diaphragm
Inlet Manifold
PTFE/PVDF
Zero Scrubber Media
Purafil chemisorbant, activated carbon & hopcalite
Thermal Management System Setpoint controlled A/C system
Software PC software for configuration,
calibration and data acquisition
Manual Gas Calibration
(optional) AIRCAL 1000 portable calibrator with
gas dilution module and zero air source
Automatic Gas Calibration
(optional)
AIRCAL 8000 integrated calibration
system with gas dilution module, zero
air source and span gas storage
Wireless communication
(optional)
Cellular IP Gateway
RF Modem
GSM Modem
Third party sensors
(optional)
Gill WindSonic (ultrasonic wind sensor)
Vaisala WTX520 (weather transmitter)
ACO Pacific SA6000 (noise monitor)
Power Requirements 100-240V AC; 100-150W
(depends on configuration)
Enclosure IIP65 fibre reinforced polycarbonate with
aluminium solar shielding and
compressor housing
Dimensions (H x W x D) in mm 900 x 555 x 400
Height with PM10 inlet : 1300
Environmental Operating Range Temperature: -20°C to +50°C;
RH: 10 to 95%
Weight 25-40 Kg
Conformity
Power Supply : EN55015, EN55022 Class B, EN61000-3-2,3, EN61000-4-2,3,4,5,6,8,11,
ENV50204, EN61547, EN61347-1, EN61347-2-13; UL1012, UL60950-1; TUV EN60950-1
Gas Modules : Part 15 FCC Rules, 2004/108/EC; EN 61000-6-1: 2001, EN 61000-6-3: 2001 Particle Monitor & Profiler : Class 1 laser;
IEC 60825-1:1998; 72/23/EEC; EN 61010-1; EN 60825-1:1996; US 21 CFR 1040.10
© Aeroqual Ltd, 2013 Aeroqual Limited MRK-D-0015, V3
All rights reserved www.aeroqual.com
DUST SENTRY
Specifications
Measurement technology Near forward light scattering nephelometry
Range 0-2000µg/m3
Accuracy +/- (2 ug/m3 + 5% of reading)
Cut points available PM10, PM2.5, PM1, or TSP
Sample flowrate 2.0 LPM
Inlet 36cm heated inlet
Alarm Relay, Email and SMS (optional)
Display 4-line alpha-numeric
Datalogging 2GB SD card (>15 years data storage)
Averaging period 1-60 minutes
Reference filter 47mm GFA circular filter (optional)
Software Datalogging and configuration software included
Outputs RS232, 4-20mA / 2-10V (optional)
Mounting Pole, tripod and wall mounting
Wireless communication options GSM/GPRS modem with GPS; Orbit DATA (cloud-based DAS)
Integrated sensor options Wind speed and direction; temp/RH; rain; pressure; noise (Class 1)
Environmental operating range -10°C to +45°C; 10 to 95% RH (NC)
Power requirements Power requirements Mains 100 - 260V, 18W (standard) or regulated
12 (+/- 2.5%) VDC with <150 mVp-p ripple and noise (15W)
Enclosure IP65-rated Lockable GRP Cabinet: Width 330mm x Depth 187mm x
Height 483mm (including solar shield armour & mounting brackets)
Weight <12kg
Conformity
(MCERTS pending)
OUTDOOR REAL-TIME PARTICULATE MONITORING
Designed for those who need to monitor and manage dust emissions as and when they happen, the Dust Sentry is a nephelometer-based instrument that delivers affordable and accurate real-time measurement of PM10, PM2.5, PM1, or TSP. Compared to reference-equivalent monitors like TEOMs and BAMs which lack sensitivity at short sampling periods, the Dust Sentry reports accurately at 1 minute intervals and has a lower total cost of ownership (up to 5x less). In addition, the Dust Sentry is compact, re-locatable and can integrate wind, noise and weather sensors for maximum utility.
Highlights
• Measures and reports data in 1 minute intervals
• Accurate measurement of PM10, PM2.5, PM1, or TSP.
• On board data storage for up to 15 years of data
• Email and GSM data retrieval and alerts
• Tough weatherproof enclosure with solar shielding for hot climates
• Option to integrate weather, wind, noise and sirens
Applications
• Construction site monitoring
• Roadside and tunnel monitoring
• Mine and quarry perimeter monitoring
• Waste transfer and treatment site monitoring
© Aeroqual Ltd, 2012 Aeroqual Limited IAQ Survey Kit April 2013
All rights reserved www.aeroqual.com
IAQ Survey Kit Portable Indoor Air Quality Monitoring
For indoor air quality consultants, building inspectors and health & safety managers who need to measure indoor air quality on the move, the Series 500 IAQ enables simultaneous measurement of up to 5 different parameters: CO, CO2, VOC, temperature and relative humidity. Plus, by adding any one of our many interchangeable sensor heads, the monitor can be further expanded to measure any target gas you choose.
The IAQ Survey Kit includes:
• Series 500 IAQ portable lightweight monitor
• Built-in temperature and humidity sensor
• Long life lithium battery for up to 8 hours in the field
• Onboard data logging
• High and low alarms
• Location ID to link measurements to location
• Rugged carry case to protect your equipment (optional)
• R42 calibration kit to allow regular calibration (optional)
• BUY our 3-in-1 multi-sensor head and get one single gas head absolutely free*
Sensor Heads Available 3-in-1: CO2, CO, VOC
2-in-1: CO2, CO Plus a full range of single gas sensor heads: Ammonia (NH3) Formaldehyde ( Hydrogen (H2) Hydrogen sulphide (H2S) Methane (CH4) Nitrogen dioxide (NO2) Non methane hydrocarbon (NMHC) Ozone (O3) Perchloroethylene Sulphur dioxide (SO2) See Sensor Specifications datasheet for full details
© Aeroqual Ltd, 2012 Aeroqual Limited IAQ Survey Kit April 2013
All rights reserved www.aeroqual.com
Series 500 IAQ Specifications
Measurement units Gas: ppm or mg/m3 | Humidity: % | Temperature °C or F
Reading functions Instant, minimum, maximum, average
Alarm features Low alarm, high alarm, mute (configurable)
Display status indicators Alarm, battery, datalogging, sensor, standby, monitor and location ID
Audible alarm Low and/or high alarm setpoints (with mute)
External signal functions Low alarm, high Alarm, control (150mA max)
Sensor calibration features Zero calibration, gain adjustment
Analog output 0-5V
Digital interface RS232 to USB
Data logging capacity Up to 8,188 records (2,706 incl. temp/RH)
PC data logging Software and data cable supplied
Clock function Real time
Power supply 12V DC (power adaptor/charger supplied 100-250V AC)
Rechargeable battery Lithium polymer 12V DC | 2700mA/h (2 hr charge time / 8 hr run time)
Enclosure material and rating PC and ABS; IP20 and NEMA 1 equivalent
Size (with sensor head) 195 x 122 x 54 (mm); 7⅝ x 4¾ x 2⅛ (in)
Weight (with sensor head and battery) < 460 g; < 16 oz
Environmental operating conditions Temperature: -5 oC to 45 oC ; Humidity: 0 to 95% non-condensating
Temperature & Humidity sensor Range -40°C to 124°C (-40°F to 255°F); Range 0 to 100% RH
Optional accessories Remote sensor kit, spare battery, car adaptor, wall bracket, carry case
Approvals Part 15 of FCC Rules; EN 50082-1: 1997; EN 50081-1: 1992
*Offer cannot be used in conjunction with any other promotional offer and is subject to review at any time. Excludes CO2, VOC (PID), MS1 / MS2 sensor heads.
© Aeroqual Ltd, 2012 Aeroqual Limited
All rights reserved www.aeroqual.com January 2013
Series 500
Portable Gas Monitor
The Series 500 monitor from Aeroqual is a feature-rich portable monitor with the ability to accurately measure multiple target gases at different concentrations in indoor and outdoor applications.
Built-in data-logging and a long-life, fast-charging lithium battery makes the Series 500 the ultimate choice for air quality professionals, consultants, and researchers.
• Built-in data-logging
• Lithium battery as standard
• PC software (Windows 7, 8, XP)
• Connect to PC via USB cable
• High and low alarms, control output
• Link data to a specific location and monitor
• Interchangeable gas sensor heads (30+ choices)
• Temperature and RH sensor optional (plug-and-play)
Specifications
Measurement units Gas: ppm or mg/m3 | Humidity: % | Temperature °C or F
Reading functions Instant, minimum, maximum, average
Alarm features Low alarm, high alarm, mute (configurable)
Display status indicators Alarm, battery, datalogging, sensor, standby, monitor and location ID
Audible alarm Low and/or high alarm setpoints (with mute)
External signal functions Low alarm, high Alarm, control (150mA max)
Sensor calibration features Zero calibration, gain adjustment
Analog output 0-5V
Digital interface RS232 to USB
Data logging capacity Up to 8,188 records (2,706 incl. temp/RH)
PC data logging Software and data cable supplied
Clock function Real time
Power supply 12V DC (power adaptor/charger supplied 100-250V AC)
Rechargeable battery Lithium polymer 12V DC | 2700mA/h (2 hr charge time / 8 hr run time)
Enclosure material and rating PC and ABS; IP20 and NEMA 1 equivalent
Size (with sensor head) 195 x 122 x 54 (mm); 7⅝ x 4¾ x 2⅛ (in)
Weight (with sensor head and battery) < 460 g; < 16 oz
Environmental operating conditions Temperature: -5 oC to 45
oC ; Humidity: 0 to 95% non-condensating
Optional accessories Remote sensor kit, spare battery, car adaptor, wall bracket, carry case
Temperature & Humidity sensor Range -40°C to 124°C (-40°F to 255°F); Range 0 to 100% RH
Approvals Part 15 of FCC Rules; EN 50082-1: 1997; EN 50081-1: 1992
Sensor Heads and Accessories
Sensor heads are available for these gases:
Ammonia (NH3)
Carbon dioxide (CO2)
Carbon monoxide (CO)
Hydrogen (H2)
Hydrogen sulphide (H2S)
Methane (CH4)
Nitrogen dioxide (NO2)
Non methane hydrocarbon (NMHC)
Ozone (O3)
Sulphur dioxide (SO2)
Volatile organic compounds (VOC)
Multi-sensor head: VOC / CO / CO2 or CO / CO2
See Sensor Specifications datasheet for details
Carry Case
Wall-mount bracket
© Aeroqual Ltd, 2013 Aeroqual Limited
All rights reserved www.aeroqual.com February 2013
Series 930
Gas Transmitter & Controller
The Series 930 is a networkable monitor with control and alarm outputs, all housed in a robust water resistant enclosure. By selecting one of our many interchangeable senor heads, the Series 930 can be used in a wide range of industrial applications including gas leak detection, health and safety, and process control. Gases available: Ammonia (NH3), Carbon Monoxide (CO), Formaldehyde (CH2O), Hydrogen (H2), Hydrogen Sulphide (H2S), Methane (CH4), Non-Metal Hydrocarbon (NMHC), Nitrogen Dioxide (NO2), Ozone (O3), Sulphur Dioxide (SO2), Volatile Organic Compound (VOC).
Features
• Active sampling for higher accuracy
• Tamperproof, water-resistant enclosure
• Multiple output transmitter
• Real-time network capability
• Data-logging and network software included
• Large LED local display option
• Temperature and RH sensor option
Specifications
Power (user supplied) 24V DC, 500mA (range 22-26V DC)
Analogue output 4-20mA (opto-isolated), 12-24V
External signal type Transistor output (150mA max)
External signals (4) Low Alarm | High Alarm | Control | Diagnostics
LED Display Optional
Inputs Standby toggle
Communication RS485 (Aeroqual proprietary protocol)
Jumpers J1, J2, J3 termination resistors
Connectors Screw
ID 1 (Default) User configurable from 1 to 255
Alarm set points (2) User configurable
Control set point User configurable
Removable / replaceable / refurbish-able sensor head Yes
Sampling method Active sampling via internal sensor fan
Temperature & humidity sensor (Series 945) Range -40°C to 124°C (-40°F to 255°F) | Range 0 to 100% RH
Configuration software (standard) PC Configuration Program CD (supplied)
Data logging & networking software (optional) PC Data Logging & Networking CD (code: R60)
USB interface (optional) RS485 to USB converter (code: R53)
Power supply (optional) 24V DC DIN rail mount 100-250V AC (code: R38)
Enclosure casing Fibre reinforced polycarbonate | IP41 & NEMA 2 equivalent
Enclosure size 180 x 110 x 90 (mm); 7⅛ x 4¾ x 3½ (in)
Weight < 850 g; < 30 oz
Approvals Part 15 of FCC Rules EN 50082-1: 1997 EN 50081-1: 1992
© Aeroqual Ltd, 2013 Aeroqual Limited
All rights reserved www.aeroqual.com MRK-D-0018 V1
Series 960H
High Ozone Transmitter
The Series 960H is a wall-mounted monitor that harnesses the benefits of UV photometry to deliver stable and reliable measurement and control in high ozone applications (up to 200 ppm). Applications include food storage, water treatment, building remediation and hospitals where high ozone concentrations are used for odor control, disinfection and sterilisation purposes.
Features
• High ozone measurement range (0-200 ppm)
• IP65 / NEMA 4 enclosure
• Single-beam UV photometer
• Pump sampling via PTFE tubing (e.g. monitoring outside of a room or duct)
• Multiple outputs (transistor, 4-20mA, RS485)
• PC and network software included
• LED display and Temperature/RH sensor options
Specifications Calibrated range 0-200 ppm Ozone
Accuracy <±5% of reading
Resolution 0.1 ppm
Minimum detection limit <0.1 ppm
Sampling method Brushless DC diaphragm pump
T90 <60s
Sample flow rate 0.4 ±0.05 LPM
Wetted materials PVDF, PFA, nafion, quartz, aluminium, viton
Inlet filter 5 µm pore size, 37 mm PTFE filter
Pneumatic connections Kynar ¼” compression fittings
Environmental operating conditions Temperature: 0-40°C ; Humidity: 0-95% RH (non-condensating)
Power requirements 24V DC, 2A
4-20mA display (optional) 3.5 digit LED (blue)
Analog output 4-20mA (opto-isolated) 12-24V DC (30V DC max) maximum loop resistance 500Ω at 24V, 16 bit resolution
Digital interface RS485 (2 wire) protocol supplied
Transistor outputs 4 x transistor outputs (Control, Diagnostics, High Alarm, Low Alarm)
User configurable set points Low alarm, High alarm, Control
Inputs Standby toggle (turns off pump)
Enclosure ABS Plastic, IP65 (Except inlet and exhaust)
Software Included for configuration, PC datalogging, and networking
DC relay board 2x SPDT 10A max switching current
Optional Accessories & Spares
FM DISP01 AS R53 AS R65 AS R66 AS R67 AS R68 AS R76
Integrated 4-20mA display LED 3.5 digit (blue) Serial RS 485 to USB Converter Replacement external filters (5 microns, hydrophobic, 12 per pack) PFA sampling tube 6.25 mm OD (per meter) Replacement UV lamp & block Replacement pump Replacement set of ozone scrubbers (3x)
© Aeroqual Ltd, 2013 Aeroqual Limited
All rights reserved www.aeroqual.com MRK-D-0010 V1
SM70
Wall-Mounted Gas Monitor
With an integrated LCD display, audible alarm, relay outputs, and a choice of sensor ranges in both ozone and VOC gases – the SM70 offers unbeatable value for industrial and indoor gas monitoring.
Benefitting from the accuracy of Aeroqual’s proprietary GSS sensors, our customers use the SM70 in many indoor and industrial applications including: leak detection, health and safety monitoring, and process control.
Features
• Large format digital display
• Replaceable GSS sensors
• External control outputs
• High and low alarms
• Power adaptor/charger included
Specifications
Sensor type Analytic GSS Technology® Gas Sensitive Semiconductor
Sensor specifications Available with ozone or VOC sensors in various ranges. Please refer to sensor specification table at www.aeroqual.com.
Sampling method Active sampling
Operational mode Continuous Control or Alarm
Operating temperature 0°C to 40°C
Operating relative humidity 10% to 90% non condensing
Warm up time 10 minutes
Display 3.5 digit LCD
Relay set point User configurable
Digital output RS232 and RS485
Analog output 0 - 5 VDC (8 bit)
Relay output 24 V; 5A (max.)
Buzzer alarm (optional) Internal piezo 85 db @ 30 cm
Power supply 12 VDC; 800 mA; Plug-in AC power adaptor supplied
Enclosure rating IP20 & NEMA 1 equivalent
Enclosure dimensions 130 W x 94 H x 57 D (mm); 5 ⅛ W x 3 ¾ H x 2 ¼ D (in)
Enclosure casing Flame resistant thermoplastic PS
Enclosure mounting Screw fix
Weight < 270 g; 9.5 oz (excludes AC power adaptor)
Approvals Part 15 of FCC Rules EN 61000-6-3: 2001 EN 61000-6-1: 2001