15
Keypad User Manual 1 LCD/LED Keypad User Manual
Keypad User Manual
1
LCD/LED Keypad
User Manual
Keypad User Manual
2
About this Manual
This Manual is applicable to LCD/LED keypad.
The Manual includes instructions for using and managing the product. Pictures, charts, images and all
other information hereinafter are for description and explanation only. The information contained in
the Manual is subject to change, without notice, due to firmware updates or other reasons. Please
find the latest version in the company website (http://overseas.hikvision.com/en/).
Please use this user manual under the guidance of professionals.
Legal Disclaimer
REGARDING TO THE PRODUCT WITH INTERNET ACCESS, THE USE OF PRODUCT SHALL BE WHOLLY AT
YOUR OWN RISKS. OUR COMPANY SHALL NOT TAKE ANY RESPONSIBILITES FOR ABNORMAL
OPERATION, PRIVACY LEAKAGE OR OTHER DAMAGES RESULTING FROM CYBER ATTACK, HACKER
ATTACK, VIRUS INSPECTION, OR OTHER INTERNET SECURITY RISKS; HOWEVER, OUR COMPANY WILL
PROVIDE TIMELY TECHNICAL SUPPORT IF REQUIRED.
SURVEILLANCE LAWS VARY BY JURISDICTION. PLEASE CHECK ALL RELEVANT LAWS IN YOUR
JURISDICTION BEFORE USING THIS PRODUCT IN ORDER TO ENSURE THAT YOUR USE CONFORMS THE
APPLICABLE LAW. OUR COMPANY SHALL NOT BE LIABLE IN THE EVENT THAT THIS PRODUCT IS USED
WITH ILLEGITIMATE PURPOSES.
IN THE EVENT OF ANY CONFLICTS BETWEEN THIS MANUAL AND THE APPLICABLE LAW, THE LATER
PREVAILS.
0100001050519
Keypad User Manual
3
Regulatory Information
FCC Information
FCC compliance: This equipment has been tested and found to comply with the limits for a digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used
in accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which case
the user will be required to correct the interference at his own expense.
FCC Conditions
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may cause undesired
operation.
EU Conformity Statement
This product and - if applicable - the supplied accessories too are marked with "CE"
and comply therefore with the applicable harmonized European standards listed
under the EMC Directive 2004/108/EC, the RoHS Directive 2011/65/EU.
2012/19/EU (WEEE directive): Products marked with this symbol cannot be disposed
of as unsorted municipal waste in the European Union. For proper recycling, return
this product to your local supplier upon the purchase of equivalent new equipment,
or dispose of it at designated collection points. For more information see:
www.recyclethis.info.
2006/66/EC (battery directive): This product contains a battery that cannot be
disposed of as unsorted municipal waste in the European Union. See the product
documentation for specific battery information. The battery is marked with this
symbol, which may include lettering to indicate cadmium (Cd), lead (Pb), or mercury
(Hg). For proper recycling, return the battery to your supplier or to a designated collection point. For
more information see: www.recyclethis.info.
Industry Canada ICES-003 Compliance
This device meets the CAN ICES-3 (A)/NMB-3(A) standards requirements.
Keypad User Manual
4
Safety Instruction
These instructions are intended to ensure that the user can use the product correctly to avoid danger
or property loss.
The precaution measure is divided into ‘Warnings’ and ‘Cautions’:
Warnings: Serious injury or death may be caused if any of these warnings are neglected.
Cautions: Injury or equipment damage may be caused if any of these cautions are neglected.
Warnings Follow these safeguards to prevent
serious injury or death.
Cautions Follow these precautions to prevent
potential injury or material damage.
Warnings:
Please adopt the power adapter which can meet the safety extra low voltage (SELV) standard.
The power consumption cannot be less than the required value.
Do not connect several devices to one power adapter as an adapter overload may cause
over-heating and can be a fire hazard.
When the product is installed on a wall or ceiling, the device should be firmly fixed.
To reduce the risk of fire or electrical shock, do not expose the indoor used product to rain or
moisture.
This installation should be made by a qualified service person and should conform to all the local
codes.
Please install blackouts equipment into the power supply circuit for convenient supply
interruption.
If the product does not work properly, please contact your dealer or the nearest service center.
Never attempt to disassemble the product yourself. (We shall not assume any responsibility for
problems caused by unauthorized repair or maintenance.)
Please do not look directly into the laser light within 6 meters because laser is hazardous to
humans.
Keypad User Manual
5
Cautions:
Make sure the power supply voltage is correct before using the product.
Do not drop the product or subject it to physical shock. Do not install the product on vibratory
surface or places.
Do not expose it to high electromagnetic radiating environment.
Do not aim the lens at the strong light such as sun or incandescent lamp. The strong light can
cause fatal damage to the product.
The sensor may be burned out by a laser beam, so when any laser equipment is being used,
make sure that the surface of the sensor not be exposed to the laser beam.
For working temperature, please refer to the specification manual for details.
To avoid heat accumulation, good ventilation is required for a proper operating environment.
While shipping, the product should be packed in its original packing.
Please use the provided glove when open up the product cover. Do not touch the product cover
with fingers directly, because the acidic sweat of the fingers may erode the surface coating of the
product cover.
Please use a soft and dry cloth when clean inside and outside surfaces of the product cover. Do
not use alkaline detergents.
Improper use or replacement of the battery may result in hazard of explosion. Please use the
manufacturer recommended battery type.
6
Content Chapter 1 Introduction _____________________________________ 7
1.1 Overview _______________________________________________ 7
1.2 Appearance Description ____________________________________ 7
1.3 Keypad Beeper and Indicator________________________________ 9
Chapter 2 Installation and Wiring ___________________________ 12
2.1 Wiring Connector Description ______________________________ 12
2.2 Keypad Address Settings __________________________________ 12
2.3 Keypad Installation _______________________________________ 13
2.4 Keypad Wiring __________________________________________ 14
Chapter 3 Keypad Alarm Operation Code _____________________ 15
Keypad User Manual
7
Chapter 1 Introduction
1.1 Overview
DS-PK00/PK00M/-LCD/LED series LCD/LED alarm keypad are used for connecting
to the security control panel. It implements operations on the security control panel through programming and prompts alarm with the indicators and audio
alert.
1.2 Appearance Description
No. Description
1 Keypad
2 LED/LCD Screen
3 Control Panel
4 Indicator Bar
Control Panel
Keypad User Manual
8
Button Description
Panic Button
Programming Button
Search Button
Bypass Button
Exit Button
Stay Arming Button
Away Arming Button
Indicator Bar
Button Description
Status Indicator
Operating Indicator
Power Indicator
Arming Indicator
Stay Arming Indicator
Keypad User Manual
9
1.3 Keypad Beeper and Indicator
The keypad registration will be completed in 10 seconds after the control panel
being power on. The system then will complete the start-up and enter the properly status of working in 20 seconds.
The beeper and indicator description after powering on are shown below.
Beeper Description
No. Sound Prompt Description
1 One Beep Pressing keys prompt; The command is timed out or the command is too long.
2 Two Beeps Valid command. Uploading the report
completed.
3 Five Beeps Invalid command. Failed to upload the report in 60s.
4 Continuous Beeping
For Two Seconds Fault Prompt
5 Slowly Continuous
Beeps Entry/Exit Delay
6 Rapidly Continuous Beeps
Entry/Exit Delay, less than 10s.
7 Rapid Beeps Zone Alarm; The keyboard is not registered.
8 Three Long Beeps and Two Short Beeps
The tampering prevention of the keyboard is turned on.
9 Three Beeps Registering the keyboard completed.
10 One Beep In Two Seconds
Two minutes before auto arming/disarming;
One minute before arming for temporary password.
11 Three Beeps In One Second
One minute before auto arming/disarming; 15s before arming for temporary password.
Keypad User Manual
10
Indicator Description
Status
Working Status Indicator Working Status Indicator
Normal Solid Green System Fault Solid Red
Power
Working Status Indicator
Power On Solid Green
Stay
Working Status Indicator Working Status Indicator
Partition Perimeter
Disarmed OFF
Partition System
Perimeter Armed Orange
Arm
Working Status Indicator Working Status Indicator
Partition Armed Solid Red Partition System
Disarmed Solid Green
Password Modifying Flicking Green Fob Code Matching Flicking Green
Testing Mode Solid Red Programming Flicking Green
OPERATING
Working Status Indicator Working Status Indicator
Normal Solid Green Programming Flicking Green
Password Modifying Flicking Green Fob Code Matching Flicking Green
Engineering Mode Solid Red System Fault Flicking Orange
Keypad User Manual
11
LED Zone Indicator
Zone
Working Status Indicator Working Status Indicator
Normal OFF Fault Solid Red
Alarm Flicking Red Bypass Solid Green
Zone Indicator under Engineering Mode (The corresponding zone indicator light will turn orange when operating):
No. Description No. Description
1 Off Hook 5 Sending CID Report
2 Dialing 6 Receiving Confirmation
3 Alarm Receiver Off
Hook 7 Control Panel On Hook
4 Receiving Handshake 8 Alarm Receiver On Hook
Zone Indicator under Status Mode (The corresponding indicator light will be solid
red if there is any fault):
No. Description No. Description
1 AC Current Interrupted 5 RS-485 Device
Disconnected
2 Low Voltage of Storage
Battery 6 Wired Network Exception
3 Movement Prevention of Control Panel Turning On
7 Wireless Network
Exception
4 Telephone Line
Disconnected 8 Reserved
Keypad User Manual
12
Chapter 2 Installation and Wiring
2.1 Wiring Connector Description
No. Description
1 Loud Speaker
2 Tamper-Proof Switch
3 Wiring Connector
4 DlP Switch
2.2 Keypad Address Settings
An address is required for each alarm keypad in the system. These addresses
cannot be repeated. Once exchanging the alarm keypad, the address of the new keypad must be the same as the replaced one. You should configure the address
via DIP switch of the keypad before powering on the system. The address should be in the range of 1~31.
When it is black on the end of ON as , indicated 1; when it is black on the other end as , indicated 0.
Keypad User Manual
13
1 2 3 4 5
0001 ■
02 ■
03 ■ ■
04 ■
05 ■ ■
06 ■ ■
07 ■ ■ ■
1 2 3 4 5
08 ■
09 ■ ■
10 ■ ■
11 ■ ■ ■
12 ■ ■
13 ■ ■ ■
14 ■ ■ ■
15 ■ ■ ■ ■
1 2 3 4 5
16 ■
17 ■ ■
18 ■ ■
19 ■ ■ ■
20 ■ ■
21 ■ ■ ■
22 ■ ■ ■
23 ■ ■ ■ ■
1 2 3 4 5
24 ■ ■
25 ■ ■ ■
26 ■ ■ ■
27 ■ ■ ■ ■
28 ■ ■ ■
29 ■ ■ ■ ■
30 ■ ■ ■ ■
31 ■ ■ ■ ■ ■
Keyboard Address ON DIP
Keyboard Address
Keyboard Address
Keyboard AddressON DIPON DIPON DIP
2.3 Keypad Installation
Before You Start: Make sure that the device in the package is in good condition and all the
assembly parts are included.
Make sure that the wall is strong enough to withstand three times the weight
of the keypad.
Set the keypad address before installation. Steps:
1. Route the cables through the cable
hole of the mounting plate.
2. Secure the mounting plate on the
wall with 4 supplied screws.
3. Connect the corresponding cables.
4. Push the keypad body in the mounting plate from bottom up.
5. Fasten the keypad body with the
three buckles on the plate.
Keypad User Manual
14
6. Align the screw holes with the
screws on the bottom of both keypad and mounting plate.
7. Tighten the screws to fix the keypad on the mounting plate and complete the installation.
2.4 Keypad Wiring
The keypad wiring is shown as follows.
It is recommended to use RVVP 2*0.5 with the maximum length of 1000m for
keypad wiring.
Keypad User Manual
15
Chapter 3 Keypad Alarm Operation Code
Function Description Command
Programming/
Editing Password
Control Panel Programming 【Installer Password】【*】【0】【#】
Exit Operation 【*】【#】
Operator Password 【Operator Password】【*】【0】【#】
【User No. (3digits)】【#】
【New Password】【#】
【New Password】【#】
Testing Testing 【Password】【*】【6】【0】【#】
Alarm Center Testing 【Password】【*】【6】【1】【#】
Project Mode 【Password】【Project】【9】【0】【n】【#】
Exiting Project Mode 【Project】 or 【*】【#】
Arming/Disarming Normal(Away)Arming/Disarming 【Password】【#】
Instant Arming 【Password】【*】【7】【#】
Stay Arming 【Password】【*】【4】【#】
Clearing Alarm Clearing Under arming status 【*】【1】【#】
Bypass Bypass Zone（n） 【Password】【Bypass】【n】【n】【n】【#】
【Bypass】【n】【n】【n】【#】
nnn is the zone No.
Group Bypass 【Password】【*】【4】【1】【#】
Group Bypass 【Password】【*】【4】【2】【#】
Keypad Settings Enabling/Disabling Keypad Tone 【*】【5】【1】【#】
Enabling/Disabling Fault Prompt 【*】【5】【6】【#】
LCD Backlight Control 【*】【5】【2】【n】【n】【n】【#】
LCD Backlight Disabling 【*】【8】【#】
