1
Pipes & ings KIMPLAS Electrofusion I.C. Reducer PIPING SYSTEMS LTD for GASATER - SDR 11 (ISO SS) Nominal. PRODUCT CODE .• SP Dia. 11•: •111 1•: g 01 d1 L F-T C-T dxd 32X20 R32X20BKD R32X20BKE 120 75 44 31 89 34 4 32X25 R32X25BKD R32X25BKE 100 73 44 36 87 30 4 40X20 R40X20BKD R40X20BKE 100 88 53 31 100 30 7 40X25 R40X25BKD R40X25BKE 100 92 53 36 100 30 7 40X32 R40X32BKD R40X32BKE 50 97 53 44 94 42 7 50X25 R50X25BKD R50X25BKE 60 103 65 36 110 30 7 50X32 R50X32BKD R50X32BKE 60 109 65 44 110 36 7 50X40 R50X40BKD R50X40BKE 60 118 65 53 110 46 7 63X32 R63X32BKD R63X32BKE 42 173 81 44 106 47 7 63X40 R63X40BKD R63X40BKE 40 187 81 53 119 42 7 63X50 R63X50BKD R63X50BKE 35 205 81 65 120 45 7 Note: SP= Standard Pack Quantity, g= Weight in Grams, F-T= Fusion Time in seconds, C-T= cooling time in minute Kimplas Electro-fusion reducers, manufactured in PE 100 Black grade are Standard SOR 11 rated (PN 16). For exact recommendations on compatibility, for welding with SDR 9 through SDR 21 or PN 6 through PN 16 pipe, refer Kimplas Technical Specifications Manual. Kimplas Electrofusion fittings are suitable for permanently connecting MOPE 80 and PE 100 pipes, both in straight form as well as coiled form. Standards: EF Reducer comply with EN 1555-part 3 PE pipe compatibility- IS: 14885, EN 1555-2, IS: 4984, EN 12201-2, ISO: 4437 DIN: 8074, ISO: 4427. Common Applications: 3 Jointing of two different diameters of Pipe in mains & distribution networks. 3 Pipe connection in areas difficult to access, in narrow trenches. 3 Major use r House Service Connections, Branch Connections, Advantages Standard operating voltage - 40 V Provided with Screws for quick connection of pipes. No need of external clamps. Fitting with integral clamping for holding and exact fitment of fitting with pipe. More connections with less effort. Save time on site. • Brings down inventory of tools and associated costs. Same fusion time r various SOR rated pipes. Optimal fusion and cold zone for a strong and sturdy joint. Transition Fitting and Pipe Stub Ends etc. 3 Pipe connections with spigot end fittings Auto Temperature compensation for ambient conditions -5 ° c to +40 ° c. I Installation: Joint preparation must be done as specified in the installation instructions. Pipe outside surface must be scraped to remove oxidised layer. Before fusing, pipe ends and spigot end of the fittings must be cleaned to remove dirt and Contamination. Complete Installation Manual may be downloaded. Permanent Batch Indicator, Raw Material Grade and SOR marking. Each fitting individually packed in PE bag to protect against contamination and oxidation. O 18001 .. � -·- �WRAS APPROVED MATERIAL For details about our other products and specifications please refer the corporate website Disclaimer: K,mplas resee the nght to modify product without pnor notice, as part of ,ts continual improvement programme. Whilst every affort is taken to ensure the accuracy of information contained in the data Sheet, K1mplas accepts no hab1hty for matters arising as a result of errors or om,ss,ons. PT KARO GRAHA ABADI Crystal Shophouse CRL No 7 Jl Gading Golf Boulevard Gading Serpong - Indonesia, 15810 TEL.: +62 21 5421 3636 MAIL : [email protected] WEBSITE : www.karograha.com
