KODICOM DigiNet System Windows 98 Installation Manual DigiNet – 3408,3416,44XX Application.

KODICOMKODICOM

DigiNet System

Windows 98 Installation Manual

WWW.KODICOM.COM

DigiNet – 3408,3416,44XX Application

-2-

1. Introduction

1.1 1.1 일반적인 사항일반적인 사항 Thank you for purchasing DigiNet System

This manual is intended to work as a guide for installation and operation of all

DigiNet System series (DigiNet-3408,3416,44xx) at both Site and Center.

This manual tells you how to install, connect, set-up and begin DigiNet Systems with

your Windows. It also provides detailed information on various components and

technical functions as well.

This manual is for users who are not familiar with the DigiNet Systems, but also for

those who have experience with other digital video recorders of a similar type. Therefore make sure to read

this step-by-step instructions thoroughly whether you are

beginner with the digital video recorder or not.

After purchasing of DigiNet, if you are in need of opening the case for function

addition, modification, contact your dealer for assistance. Also, when you have any

further questions which can not be solved by yourselves by following this manual,

consult with your dealer.

-3-

1.2 1.2 PrecautionsPrecautions

When you select a place for your DigiNet System seating,

avoid the following locations

q Location with excessive heat, such as direct lay of light or heating appliances

q Location with excessive moisture, dust and smoke

q Location with magnetic field or electric wave equipment close by

q Location exposed to excessive cold or hot temperature

(Operating Temp : 5 °C ~ 35 °C)

q Location with unstable or unleveled surface

Before you install this system consider the following precautions .

q Be sure to switch the power on as the last step after all of the necessary

connections are completely finished.

q Make sure that you have sufficient space around the system for cable

connection.

q Place the system on a level, stable and cool surface.

q If you place the system near any wireless electronic machines that can

generate a strong magnetic field such as wireless TV, radio or base units of

cordless telephones, they may damage to the System.

q Keep the system clean. Dust or any foreign objects accumulated through the

speaker openings can cause problems.Do not try to dismantle the system by yourself. Contact dealers for such servicing.

-4-

2.My Computer

2.1 Disk Cleanup

Open My Computer by double-clicking the icon.

Click right button of mouse on DigiNet (C:) icon and

then go to Properties.

Click Disk Cleanup.32

1

-5-

[Disk Cleanup] -> [Files to delete]

Select files to be deleted.

4 [Setting] Click .5

6 If you click Settings, a dialogue “ If this drive

runs low space, automatically run disk cleanup”

appears. Keep this check box unchecked,

Now click OK.

If you click OK, a dialogue box with “Are

you sure you want to delete files?”

appears. Click Yes and OK to exit .

☞ Must be set above all drives

-6-

2.2 Scan Disk

Open My Computer and point [C:]. If you

click the right button on [C:], you can pick up

Properties. Click Properties and then click Tools.

12 Select Error-checking status and click Click now .

In Scandisk, Click Advanced.3

!

NOTE: It is recommended for you to perform scandisk when you change any of Scandisk Advanced

options. If not, preset options are still valid .

Option Choice (recommended)

[Display Summary] ⊙Never

[Log file] ⊙No Log

[Cross Linked Files] ⊙Delete

[Lost File Fragments] ⊙Free

In Scandisk Advanced Options window,

select options below and Click OK .

4

-7-

3. Control Panel

3.1 Display

3.1.1 Display Screen Set-up-Screen Saver

Click My Computer, and Control Panel. 1 Double-click Display icon.2

Click Screen Saver. 3Select None and click Settings.4

Caution: For Continuous display of DigiNet System, no Screen Saver should

be active on your monitor.

!

-8-

3.1.2 Display Screen Set-up Color & Resolution

In Display Properties window, select Settings .1 2

NOTE: Screen colour of 32bit and screen

pixels of 1024X768 support DigiNet

System Display .

Set the colour and pixels size as below and

click Advanced .

!

3 Select Small Fonts and ⊙Ask me before

applying the new colour settings and click OK to save and exit .

-9-

3.2 Power Management

Double-Click My Computer -> Control Panel-> Power management1

2

Select ‘Select ‘Always On’Always On’ in in Power SchemesPower Schemes, ‘, ‘NeverNever’ ’ in in System StandbySystem Standby, ,

‘‘NeverNever’ in ’ in Turn Off MonitorTurn Off Monitor, ,

‘‘NeverNever’ in ’ in Turn off Hard DisksTurn off Hard Disks and click and click OKOK

-10-

4. Windows Explorer

4.1 Folder Setup

1 Double click Windows Explorer icon . 2 Click View and Folders Option .

3 Select View and click . 4 Click Show all files and OK .

NOTE: If you do not select Show all files, some of files can be missing when you make copy.!

-11-

5. Recycle Bin

Click Recycle Bin icon and click Properties again .1 2 Select Use one setting for all drives and check

Do not move files to the Recycle Bin and click OK .

In Windows 98, when you delete files, those files go to the Recycle Bin to store automatically.

But automatic saving in Recycle Bin is not recommended in DigiNet System. Therefore, you are

requested to execute set-up procedure to delete data files immediately without storing to Recycle Bin.

Caution: Be sure to mind that after this setting the deleted files are erased without leaving

any copy in the Recycle Bin in DigiNet System .!

!

Must be uncheck

-12-

6. COM Port Setup

Double Click My computer-> Control Panel -> System .

1

Click Device Manager .2

Need to reinstall if the communication port

is not setup either the communication port

is setup and control card is working at mean

time.

3 Double Click COM & LPT and Click OK .

!

-13-

7. Config.sys Autoexec.bat

1 Click Start and click on Run . 2 Type “sysedit” and click OK.

3 Find out C:CONFIG.SYS file and press Enter .

DEVICE=C:\WINDOWS\HIMEM.SYS

DEVICE=C:\WINDOWS\EMM386.EXE NOEMS

DOS=HIGH,UMB

FILES=50

BUFFERS=50

LASTDRIVE=Z

4 Click AUTOEXEC.BAT

NOTE: Above setting is for DigiNet System

which has drive for data up to “O”

@ECHO OFF

LH C:\WINDOWS\SMARTDRV.EXE A+ B- C+ D+ E+ F+ G+ /L

!

-14-

8. DigiNet Program Removal/Reinstall

8.1 DigiNet Program Removal

NOTE: If you want to reinstall DigiNet program, you should consider belows first

Remove the existing DigiNet program already installed.

Delete Watch Dog Reader program (press Ctrl+Shift+Alt and F4 sequentially, and you can see

Watch Dog Reader at the task bar buttons. Click and click again⊠ to erase)

Copy Drive A.dat file and Drive A.txt file for back-up. After DigiNet program is reset, those two

files should back to C:\DigiNet\Data file. If not, some of saved image data may be lost in case.

(press Windows Explore | [C:] | DigiNet | Data, and pick up Drive A.dat and Drive A.txt files)

For more detail, contact your dealer.

!

1 Double-click My Computer -> Control Panel -> Add/Remove Programs.

2 Select DigiNet Site and click Add/Remove.

3 Click Yes.

4 Click OK.

-15-

9. Video Driver Reinstall

1 Double click My Computer -> Control Panel -> Display. 2 Click Settings -> Advanced .

3 Click Adapter -> Change. 4 Click Next.

-16-

5 Click Next. 6 Click Specify a Location and click on .

Select a folder which contains driver information and click .

7 Select sub-folder of VGA. In case of ATI VGA,

select below and click OK.

“C:\DigiNet\backup\VGA-ATI(16)128 Rage fury “

8 Click Next. 9 Click Next.

-17-

10 Click Finish.

11 Click Yes.

-18-

10. HDD CONFIGURATION

Must be check !!

-19-

11. HDD Partition Setup

Insert Booting Diskette to A: drive and turn on the power.

Then it will be boot by floppy diskette.

1

Type FDISK and press Enter key2

Why does DVR have to be divided partition in Hard disk.

▶ As DigiNet save data to Hard disk, DVR is not overwrite to Hard disk but automatically format

drive and save data to Hard disk.

1. After installing DVR and perform DVR at the beginning, format drive D and save data.

2. Automatically format drive E, if D drive is full.

3. Rest of the drive will be proceeded as same as No.2

4. If Hard drive is full, automatically format drive D again and save data and previous data will not

be existed.

▶ Therefore, each partition of drive will be divided as possible as small size(1~2GB), but is need for

your attention, if you have plan to add Hard disk.

▶ Each saving data drive will be divided from D to Y maximally

If it is included backup system, the system will be required a drive, so last two drives will

be made for backup.

Microsoft(R) Windows 98

(C) Copyright Microsoft Corp 1981-1999

A:\>

A:\>FDISK

This is the example of “FDISK” when 20GB Hard is installed.

-20-

HDD Size is over 2GB, so press Enter key 3

You computer has a disk larger than 512 MB. This version of Windows

includes improved support for large disks. Resulting in more efficient

use of disk space on large drivers, and allowing disks over 2 GB to be

IMPORTANT : If you enable large disk support and create any new drives on this

Disk, you will not be able to access the new drive(s) using other operating

system, including some versions of Windows 95 and Windows NT, as well as

earlier versions of Windows of Windows and MS-DOS. In addition, disk utilities that

Were not designed explicitly for the FAT32 files system will not be able

To work with this disk. If you need to access this disk with other operating

systems or older disk utilities, do not enable large drive support.

Do you wish to enable large disk support (Y/N)……………………..….? [Y]

Should be created Dos partition is Logical Dos drive, so press Enter key4

Microsoft Windows 98

Fixed Disk Setup Program

(C) Copyright Microsoft Corp. 1983 – 1998

FDISK Options

Current fixed disk drive : 1

Choose one of the following:

1. Create DOS partition or Logical DOS Drive

2. Set active partition

3. Delete partition or Logical DOS Drive

4. Display partition information

5. Change current fixed disk drive

Enter choice : [1]

Press Esc to exit FDISK

-21-

First, it should be created primary Dos partition.5

Create DOS Partition or Logical DOS Drive


Choose one of the following :

1. Create Primary DOS Partition

2. Create Extended DOS Partition

3. Create Logical DOS Drive(s) in the Extended DOS Partition

Enter choice : [1]

Press Esc to return to FDISK Options

Create Primary DOS Partition


Verifying drive integrity, 10% Complete.



Do you wish to use the maximum available size for a Primary DOS Partition

(Y/N)………………………………………………………………….? [Y]


Check to drive

-22-



Total disk space is 19571 Mbytes (1 Mbyte = 1048576 bytes)


Type “N” then press Enter key6



Total disk space is 19571 Mbytes (1 Mbyte= 1048576 bytes)

Maximum space available for partition is 19571 Mbytes (100%)

Enter partition size in Mbytes or percent of disk space (%) to

create a Primary DOS Partition……………………………………………………[19571]


Check to drive



Do you wish to use the maximum available size for a Primary DOS Partition

(Y/N)………………………………………………………………….? [N]


This is to create “Primary DOS partition”

-23-

Type “2048” then press Enter key7



Partition Status Type Volume Label Mbytes System Usage

C: 1 PRI DOS 2048 UNKNOWN 10%

Primary DOS Partition created, drive letters changed or added

Press Esc to Continue

Press Enter key9

Press Esc key8





Enter partition size in Mbytes or percent of disk space (%) to

create a Primary DOS Partition……………………………………………………[2048]





FDISK Options








Enter choice : [1]


-24-


Create Extended DOS Partition











Enter partition size in Mbytes or percent of space (%) to

create an Extended DOS Partition.………………………………………………[17524]

Press Esc to return to FDISK Options.

This step is to Create “Extended DOS partition” Press Enter key

Check to drive

11







Enter choice : [2]


-25-

Press Esc key





EXT DOS 17524 UMKNOWN 90%

Extended DOS Partition created.


Created Logical DOS Drive(s) in the Extended DOS Partition

No logical drives defined




Total Extended DOS Partition size is 17524 Mbytes (1 Mbyte= 1048576 bytes)

Maximum space available for logical drive is 17524 Mbytes (100%)

Enter logical drive size in Mbytes or percent of disk space (%).………………[17524]

Logical DOS Drive created, drive letters changed or added


12

Check to drive

This is to create “Logical DOS drive(s)” in the “Extended DOS partition”

-26-


Drv Volume Label Mbytes System Usage

D: 17524 UNKNOWN 100%

All available space in the Extended DOS Partition

is assigned to logical drives.

Press Esc to continue

13Type “17524” or “100%”, then press Enter key







D: Drive is created in the “Extended DOS partition”, then press ESC key

-27-

14




FDISK Options








Enter choice : [5]


When you try to install more than two HDD, Type "5" and press "enter" since you have to change the current drive.

Display Partition Information

Disk Drv Mbytes Free Usage

1 19571 100%

C: 2048

D: 17524

2 19571 19571 %

(1 MB= 1048576 bytes)

Enter Fixed Disk Drive Number (1-2)…………………………………[2]

Press Esc to return to FDISK Option

Type “2” , then press Enter key15

-28-

Check “Change current fixed disk drive” are created normally.




FDISK Options








Enter choice : [1]


16

Should be created Dos partition is Logical Dos drive, so press Enter key




FDISK Options








Enter choice : [1]


17

-29-





Check to drive







Enter choice : [2]






Enter partition size in Mbytes or percent of space (%) to

create an Extended DOS Partition.………………………………………………[19563]

Press Esc to return to FDISK Options.

This step is to Create “Extended DOS partition” Press Enter key19

-30-

Press Esc key




1 EXT DOS 17524 UMKNOWN 100%

Extended DOS Partition created.


20




Check to drive






Logical DOS Drive created, drive letters changed or added


This is to create “Logical DOS drive(s)” in the “Extended DOS partition”

-31-



D: 19563 UNKNOWN 100%

All available space in the Extended DOS Partition

is assigned to logical drives.


21Type “19563” or “100%”, then press Enter key







D: Drive is created in the “Extended DOS partition”, then press ESC key


14If you have two HDD to add, repeat the same way from item to item 21

-32-

Type “4” , then press Enter key

22 Top menu is displayed, Check “Primary DOS Drive(s)” and “Extended DOS Drive” are created normally.

23




FDISK Options








Enter choice : [1]





FDISK Options








Enter choice : [4]


-33-



D: 17524 UNKNOWN 100%

Total Extended DOS Partition size is 17524 Mbytes (1 Mbyte = 1048576 bytes)



Current fixed disk drvie : 1




Total disk space is 12417 Mbytes ( 1 Mbyte = 1048576 bytes)

The Extended DOS Partition contains Logical DOS Drivers.

Do you want to display the logical drive information (Y/N)………..…….?[Y]

Press Esc to return to FDISK option

24 Type “Y”, press Enter key

Press Esc key25

-34-

26

Top menu is displayed

To boot normally “ Active partition must be set. Type “2”, Press Enter key




FDISK Options








Enter choice : [1]





FDISK Options








Enter choice : [2]


-35-

Sat Active Partition






Enter the number of the partition you want to make active…..……………...[ ]


27

“Active partition” menu is displayer

Type 1, press Enter key




C: 1 A PRI DOS 2048 UNKNOWN 10%



Partition 1 made active


“Active partition: is completed. Press Enter key28







Enter the number of the partition you want to make active…..……………...[ 1 ]


-36-

You MUST restart your system for your changes to take effect.

Any drives you have created or changed must be formatted

AFTER you restart.

shut down Windows before restarting.


30

29

FDISK is completed.



A:\>

Dos mode is displayed . You must restart your system.

Press Ctrl + Alt + Del key, or turn off power.

31




FDISK Options








Enter choice : [2]


Top menu is displayed. Press Esc key

-37-

Booting by A: Drive

A:\>

All the Drive must be formatted to use HDD.

Type “format C:”, then press Enter key.

Type “Y”, then press Enter key



A:\>FORMAT C:

A:\>FORMAT C:

WARNING, ALL DATA ON NON-REMOVABLE DISK

DRIVE C : WILL BE LOST!

Proceed with Format (Y/N) ? Y

32

33

-38-

A:\>FORMAT C:




Formatting 1,027.56M

Format complete.

Writing out file allocation table

Complete.

Calculating free space (this may take several minutes)…

Complete.

Volume label (11 characters, ENTER for none) ?

Press Y key

A:\>FORMAT C:




Formatting 1,027.56M

20 percent completed

34

Press Enter key.35

-39-

A:\>FORMAT C: /S




Formatting 2048M

Format complete.

Writing out file allocation table

Complete.

Calculating free space (this may take several minutes)…

Complete.

Volume label (11 characters, ENTER for none) ?

2,049,359,744 bytes total disk space

411,136 bytes used by system

2,049,359,744 bytes available on disk

4,096 bytes in each allocation unit.

262,538 allocation units available on disk.

Volume Serial Number is 4225-16F2

A:\>

Format rest drive(D:, E:, F:, G:…) as same way

EX)

A:\>FORMAT D:

A:\>FORMAT E:

A:\>FORMAT F:

A:\>FORMAT G:

36

Display DOS prompt mode.

Date post:	26-Mar-2015
Category:	Documents
Upload:	erin-patton
View:	220 times
Download:	0 times

KODICOM DigiNet System Windows 98 Installation Manual DigiNet – 3408,3416,44XX Application.

Documents