www.kust.de | www.kust-elektronik.com KUST ELEKTRONIK: LM1050 Precission LCR Meter LM1050 series is a new generation impedance analyser. LM1050 answer all the measurement needs for com- ponents and materials with its high basic accuracy (0.05%),wide frequency range (from 20Hz to 5MHz) and impedance range (up to 100MΩ). The instrument is es- pecially suitable for low dissipation factor (D) capacitors and high quality factor (Q) inductor measurements. List sweep function make it easy to extend user’s capability of component evaluation. LM1050 series is a powerful LCR meter for component design, component inspection, quality control and measurement on production lines. LM1050 is also a powerful tool for design and research of circuit and materials(electronic material and non- elec- tronic material). Excellent performance of the LM1050 allows conformity to commercial and military standards for example IEC and MIL. LM1050A: 20Hz - 2MHz, 10mHz resolution LM1050B: 20Hz - 5MHz, 10mHz resolution • AC Signal: f≤1MHz 10mV ~ 5V f > 1MHz 10mV ~ 1V • DC BIAS: Internal: -5V ~ +5V DC BIAS Source Optional: ±10V, (±100mA) DC Bias ±10V, 0-1A DC Bias • Basic Accuracy: 0.05% • Parameters: |Z|,|Y|,L,C,R,G,D,Q,X,B,θ,DCR • ALC - Automatic level control • Frequency response Analysis • 800 × 480 RGB 7 inch 16: 9 TFT LCD Monitor • Direct reading, Δ, Δ%, V / I monitor • 4 parameter dispaly in any configuartion • Sweep: up to 10 points: test signal, DC BIAS • Graphical results: trace sweep/frequency response • Correction/Compensation • RS232C, HANDLER, GPIB(optional) • USB DEVICE (USBTMC and USBCDC support) • USB HOST (FAT16 and FAT32 support) • Beeper - result sound indication • LED Indication: Green - PASS / Red - FAIL • Key-Lock, Password protection • Output Impedance: 10/CC, 30Ω,50Ω,100Ω • Up to 75 Measurement/sec • Trigger Function: Manual, Internal, External, BUS • Internal Memory for 100 Instrument Settings • Rresult, screenshots and settings saving to USB
Transcript
www.kust .de | www.kust-e lektronik .com
KUST ELEKTRONIK:LM1050 Precission LCR Meter
LM1050 series is a new generation impedance analyser. LM1050 answer all the measurement needs for com-ponents and materials with its high basic accuracy (0.05%),wide frequency range (from 20Hz to 5MHz) and impedance range (up to 100MΩ). The instrument is es-pecially suitable for low dissipation factor (D) capacitors and high quality factor (Q) inductor measurements. List sweep function make it easy to extend user’s capability of component evaluation. LM1050 series is a powerful LCR meter for component design, component inspection, quality control and measurement on production lines. LM1050 is also a powerful tool for design and research of circuit and materials(electronic material and non- elec-tronic material). Excellent performance of the LM1050 allows conformity to commercial and military standards for example IEC and MIL.
• AC Signal: f≤1MHz 10mV ~ 5V f > 1MHz 10mV ~ 1V• DC BIAS:Internal: -5V ~ +5V DC BIAS SourceOptional: ±10V, (±100mA) DC Bias ±10V, 0-1A DC Bias• Basic Accuracy: 0.05%• Parameters: |Z|,|Y|,L,C,R,G,D,Q,X,B,θ,DCR• ALC - Automatic level control• Frequency response Analysis• 800 × 480 RGB 7 inch 16: 9 TFT LCD Monitor• Direct reading, Δ, Δ%, V / I monitor• 4 parameter dispaly in any configuartion• Sweep: up to 10 points: test signal, DC BIAS• Graphical results: trace sweep/frequency response• Correction/Compensation• RS232C, HANDLER, GPIB(optional)• USB DEVICE (USBTMC and USBCDC support)• USB HOST (FAT16 and FAT32 support)• Beeper - result sound indication• LED Indication: Green - PASS / Red - FAIL• Key-Lock, Password protection• Output Impedance: 10/CC, 30Ω,50Ω,100Ω• Up to 75 Measurement/sec• Trigger Function: Manual, Internal, External, BUS• Internal Memory for 100 Instrument Settings• Rresult, screenshots and settings saving to USB
www.kust .de | www.kust-e lektronik .com
Measurement function:
Test frequency:LM1050A 20 Hz-2MHz, 10mHz Resolution
LM1050B 20 Hz-5MHz, 10mHz Resolution
Test parameters: | Z |, | Y |, C, L, X, B, R, G, D, Q, θ, DCRBasic accuracy: 0.05%The equivalent circuit: Series, parallelMathematical functions: The absolute value of the deviation, percentage deviationRange mode: Automatic, hold, manually selectTrigger: Internal, manual, external, bus
Measurement speed (≥1kHz): Fast: 200 times / sec, Medium: 12 times / sec, Slow: 3 times / sec
Averaging: 1-255Delay time: 0-60s, with 1ms stepCompensation: Open / short / loadTest side configuration: Five endList sweep: 10 points list sweep functionDisplay mode: Direct reading, Δ, Δ%, V / I (measured voltage / current monitoring)
Test signal level:f≤ 1MHz 10mV ~ 5V, ± (10% + 10mV) f> 1MHz 10mV ~ 1V, ± (20% + 10mV)
DC BiasInternal: -5V ~ + 5V DC BIAS voltage source, Accuracy: 1%
Optional:± 10V, ± 100mA DC BBIAS Source± 10V, 0-1A DC BIAS Source
Display range:| Z |, R, X 0.01mΩ - 99.9999MΩDCR 0.01mΩ - 99.9999MΩ| Y |, G, B 0.00001μS - 99.9999SC 0.00001pF - 9.9999FL 0.00001μH - 9999.99HD 0.00001 - 9.9999Q 0.00001 - 9999.9θ (DEG) -179.999º -179.999 ºθ (RAD) -3.14159 - 3.14159OtherOutput: 4 Terminals – 4 wire Connection. Ground terminal.Result Indication: Green / Red LED, soundTrace Sweep: 801 points, graph display, 2 parametersResult display: 4 parameters in any configurationData logging Displayed parameters, sweep and trace list, CSV file format.Comparator function Nine in ten stages qualified file, a file failed, while a subsidiary AUX fileMemory 100 internal instrument settings for storage / recall, USB memoryInterface RS232C, HANDLER, USB HOST, headphone jack, optional: GPIB
KUST Elektronik
www.kust .de | www.kust-e lektronik .com
LM1050 Precision LCR meter:KUST LM1050 Precision LCR meter is a industry leader at both high and low impedance measurments. • High accuracy• Fast measurement• High Stbility Allow user to characrterise perfectly components like:capacitors, inductors or non-electrical materialsLoad correction and compensation eliminates any errors caused by cables and assures correct measurment every time. LM1050 LCR Meter allows: • Great Productivity• Lower test cost• Higher fail detection ration
LM1050 is supplied as standard with range of accessories allowing testing straight out of the box:
Optional accessories:
KA1005 SMD test fixture - pin/leg typeKA1006 SMD test fixture -pad typeKA1007 SMD test tweezersKA1025 GPIB interfaceKA1022 DC BIAS 0V - 10V / 0 - 100mAKA1023 DC BIAS 0V - 10V / 0 - 1A
LM1050 requires the following power source:Voltage: 198 to 242 VacFrequency: 47 to 66 HzPower: 90 VA maximum
LM1050 must be operated under within the fol-lowing environment conditions:Temperature: 0 to 40Humidity: less then 90% RH
Every LM1050 LCR Meter is supplied with main’s lead and factory calibration.
