NEW FEATURES & FUNCTIONS VER.5
KX-TDE/NCP
Note
New SLC (MCSLC) Card (KX-TDA1176/TDA1178) KX-TDE100/200 only KX-NCP500 Capacity Expansion KX-NCP500 only Maximum ICD-G Queuing : 30→100 Caller can exit from ICD-G Queuing Automatic start 2-way Recording Emergency Alert (SMDR) Conference Group with Auto-Answer Function One Touch Busy Override Tenant based ARS Improves Service Out Function CLIP when VM Transfer Incoming Call LCD Improves ICD Group Call Log Improves VM connection
New Features/Functions - 1 The new features/functions are available from, - KX-TDE100/200/600 MPR Ver.5. - KX-NCP500/1000 MPR Ver.5.
Note
Improves SIP Trunk feature - T.38 disable mode is supported. - Forward CLIP (A-number) for SIP trunk - Refer Transfer is supported for SIP trunk - P-Asserted-Identity header is supported for SIP trunk - CODEC Priority Notification from SIP network - Improves FAX Connect ability - Redundancy Function is supported for SIP trunk - Delete alphabet Caller-ID
SIP Phone Feature RU/UA Model Only PCMC ID Lock
New Features/Functions – 2 The new features/functions are available from,
- KX-TDE100/200/600 MPR Ver.5. - KX-NCP500/1000 MPR Ver.5.
NEW SLC (MCSLC) CARDS KX-TDA1176 (MCSLC-16) KX-TDA1178 (MCSLC-24)
For KX-TDE100/200 (Ver.5)only
TDE100 Max. S Power 4 M Power 6
TDE200 Max. M Power 8 L Power 8
KX-TDA1176 (MCSLC16)
- 16 Port Single Line Telephone Ext. with Caller ID and Message Lamp Card
- KX-TDE0105 (MEC card) is needed.
- Standby power consumptions: 9W
One SLT goes to Off-hook mode, additionally 0.35W will be consumed.
- KX-TDE600 does NOT support KX-TDA1176.
Cable Maximum Distance ø 0.4 mm: 698 m ø 0.5 mm: 1,128 m ø 0.6 mm: 1,798 m CAT 5: 1,128 m
TDE100 Max. S Power 2 M Power 5
TDE200 Max. M Power 5 L Power 5
KX-TDA1178 (MCSLC24)
- 24 Port Single Line Telephone Ext. with Caller ID and Message Lamp Card
- KX-TDE0105 (MEC card) is needed.
- Standby power consumptions: 11W
One SLT goes to Off-hook mode, additionally 0.35W will be consumed.
- KX-TDE600 does NOT support KX-TDA1178.
Cable Maximum Distance ø 0.4 mm: 698 m ø 0.5 mm: 1,128 m ø 0.6 mm: 1,798 m CAT 5: 1,128 m
PBX Power unit
SLT Capacity Ver. 4
SLT Capacity Ver.5 New
KX-TDE100 (6 Slot)
S 64 = 16x4 64 = 24x2 + 16x1
M 96 = 16x6 128 = 24x5 + 8x1
KX-TDE200 (8 Slot for Extension)
M 128 = 16x8 128 = 24x5 + 8x1
L 128 = 16x8 168 = 24x5 + 16x3
KX-TDA1176/1178 (MCSLC16/24) Maximum SLT capacity of KX-TDE100/200 is as follows.
KX-NCP500 CAPACITY EXPANSION
KX-TDE/NCP Version 5
NCP500 Ver.5
The current NCP500 hardware with Ver.5 software can support the below specification.
NCP500 Ver. 4 NCP500 Ver. 5 NCP1000 Ver.4/5
Telephone
Max. 156 172 172 SLT 24 36 *) 36 DT3xx/T76xx 20 40 W/DXDP 40 T7650/T7656 20 36 36 Other DPT 6 10 10 APT 4 4 4 IP-PT 128 128 128 SIP Ext. 128 128 128
DSS console 8 8 8
CS
Max. 32 32 32 2ch CS 7 11 11 8ch CS **) 3 5 5 IP-CS **) 16 16 16
Power Factor (Software S/W) 28 44 44 PS 64 64 64
NCP500 Capacity Expansion
*) 2 x DLC16 or SLC16 Required = Cannot use OPB3 (& Door phone card)
**) One 8ch CS counts as 2 x 2ch CS.
CS Power unit and System total number of CS NCP500 Ver. 4 NCP500 Ver. 5 NCP1000 Ver.4/5
Max. CS Power units 32 32 32 2ch CS 1 1 1 8ch CS 2 2 2 IP-CS 2 2 2
System total number of CS 19 21 21
NCP500 Ver. 4 NCP500 Ver. 5 NCP1000 Ver.4/5 2ch CS 7 11 11 8ch CS 3 5 5 IP-CS 16 16 16 PS 64 64 64
NCP500 Capacity Expansion NCP500 Ver.5
The current NCP500 hardware with Ver.5 software can support the below specification.
MAXIMUM ICD-G QUEUING: 30→100
KX-TDE/NCP Version 5
ICD-G 600
ICD-G 600
CO Queuing Table Max. 30
Default : 30
Queuing Table Max. 100
No Optional Programming
Maximum ICD-G Queuing : 30 → 100 Before Ver.5 (Max. 30)
CO
TDE/NCP Ver.5 (Max. 100)
CALLER CAN EXIT FROM ICD-G QUEUING
KX-TDE/NCP Version 5
OGM-1: Welcome to Panasonic….. OGM-2: Please wait for the moment.
Customer Request function
External call
The user wants to exit from the queuing and leave a message in the mail box.
Cycles forever
Caller can exit from ICD-G Queuing Before Ver.5
Once an external call goes into an ICD-G queuing table, the caller has only two options, wait for the call to be answered by the ICD-G agent or disconnect the line.
External call
Ext.202 Dial “2”
Ext.500 Dial “0”
Ext.201 Dial “1”
No AA Service
- Only AA is available (not DISA - dial extension number). - When the caller is listening to the BGM/MOH (wait
period), the DISA AA function does not work.
Caller can exit from ICD-G Queuing TDE/NCP Ver.5
The ICD-G Queuing OGM performs not only sending OGM but also DISA AA service. When the caller is listening the OGM, the caller can exit to an extension specified by AA.
ICD-G: 601
VM Group:500
Mail Box: 601
DISA 502: Dial 0 → 500
Caller can exit from ICD-G Queuing TDE/NCP Ver.5 + If a VM is connected to the PBX
If a system has a VM and an ICD-G has a VM mail box, the caller has three options, wait for the call to be answered by the ICD-G agent, disconnect the line or leave a message to a mail box.
External call
OGM-1: Welcome to Panasonic….. OGM-2: Please wait for the moment. Or dial “0” to leave voice message.
VM Mail Box 601
Dial “0”
Add Message
Caller can exit from ICD-G Queuing TDE/NCP Ver.5 + If a VM is connected to the PBX
TDE/NCP Ver.5 + If a VM is connected to the PBX
VM custom service is also available
Program Point
VM Custom Service
Dial “0”
VM Group:500
Custom Service
DISA 502: Dial 0 → 500
External call
Select
Caller can exit from ICD-G Queuing
ICD-G: 601
Exit
Dial Dial
Caller can exit from ICD-G Queuing Limitation
Only when the caller is listening the OGM (OGM-2), the caller can exit to the extension specified by AA. When the caller is listening the BGM/MOH (wait period), the OGM-2 DISA AA function does not work.
Counter Idea
Change wait period to OGM-3 (OGM-3 records MOH/BGM)
- VM in other PBX (Centralized VM) can NOT be DISA-AA destination.
VM Group: 500
VM Group
D-PT integration
DISA 502: Dial 0 → 500
Centralized VM
Caller can exit from ICD-G Queuing TDE/NCP Ver.5 Technical Condition
- VM has to be KX-TVA/TVM using Digital (PT) integration.
1.External call
ESVM:599
ICD-G: 601
DISA 502: Dial 0 → 599
Ext.2002
Ext.2003
Ext.2001
2. Dial 0
3. Go to Ext.2001 SVM
- Ext.2001 has to have an SVM box. - A setup of C-FWD to SVM on Ext.2001 is not necessary.
The SVM of the 1st ICD-G member will answer after the caller dials digit 0.
ESVM box
Caller can exit from ICD-G Queuing What if a Customer wants to use ESVM for recording a message?
ESVM floating extension number can be assigned in the DISA AA destination.
AUTOMATIC START 2-WAY RECORDING
KX-TDE/NCP Version 5
1- Call to Ext.2001
Ext.2001
Three party conference
1- Call to Ext.2001 2- Ext.2001 answers the call. 3- The PBX starts 2 way recording automatically.
2- Answer
3- 2-way Recording
Before Ver.5 1- Call to Ext.2001 2- Ext.2001 answers the call. 3- Press “2-way recording” button to start 2 way recording.
Automatic start 2-way Recording TDE/NCP Ver.5
CO
Manual Recording
Condition - PT(IP/Digital/Analog), PS and SLT can use this function. - SIP Phone can NOT use this function. - Internal call/External call/ICD-G call is automatically recorded. - Incoming call/Outgoing call is automatically recorded. - We cannot change the above-mentioned conditions (E.g. Only external incoming call is automatically recorded) - Programming “2-way recording” button is not necessary. If you program a 2-way recording button, it can be used to stop and then re-start 2-Way recording”.
Once it is programmed it will always start automatically “2-way recording”. A manual start cannot be performed.
Automatic Recording
Automatic start 2-way Recording TDE/NCP Ver.5 (New Program Item)
Automatic start 2-way Recording Technical Specifications
The Max. number of simultaneous recordings
NCP/TDE100,200 TDE600 (Basic) TDE600 (Basic)
+ 3 x TDE620
Max. 10 10 40
Condition 3 x TVM50 1 x TVM200
3 x TVM50 1 x TVM200
2 x TVM200
– A maximum of 10 calls can be recorded to VM for NCP and TDE100/200 at the same time (PBX supports 10 x 3 conference)
– A maximum of 24 calls can be recorded to one VM for TDE600, because one VM supports 24ch.
– A maximum of 40 calls can be recorded to two or more VM for TDE600, because TDE600 supports10 x 3 conference hardware per cabinet.
– VM has to be KX-TVA/TVM using Digital (PT) integration.
– VM DTMF integration does NOT support automatic recording.
– Centralized voice mail does NOT support automatic recording.
– E-SVM card cannot be used this function.
Ext.2002
All operator conversation
Ext.2001
Manager
Ext.1001
Mail Box Ext. No 201 1001
Programming Point
Automatic start 2-way Recording TDE/NCP Ver.5
It is also possible to record all of the conversation to one mail box.
E.g.
• Ext.1001 (Manager) has a mail box 201.
• Ext.2001, Ext2002 (Operator) conversation can be recorded on the mail box 201.
• Only Ext.1001 can listen to the recorded message.
EMERGENCY ALERT (SMDR) KX-TDE/NCP Version 5
Before Ver.5 After finishing the call, this extension number is outputted to SMDR, only.
“Emergency Dial” table
Ext.2001
SDMR (RS232C/LAN)
Emergency Call
Ver.5 New
Emergency Alert (SMDR) TDE/NCP Ver.5
If a dialed number is matched with the “Emergency Dial” table, when dialing is completed, the extension number is outputted to SMDR (1st SDMR). Also, after finishing the call, this extension number is outputted to SMDR (2nd SMDR).
CO
Option Ver.5 function
Default Ver.4 function
Emergency Alert (SMDR) Related Programming
“Emergency Dial” table SDMR
(RS232C/LAN)
CA Call Account
If the CA call account software is installed to a PC, we can see an Emergency call alert by a popup window, after dialing is completed. - Version up is NOT required for CA Call Accounting
software.
Emergency Alert (SMDR)
CO
Ext.2001 Emergency Call
CONFERENCE GROUP WITH AUTO-ANSWER FUNCTION
KX-TDE/NCP Version 5
1.Dial *321#
Ext.2003 Ext.2001 Ext.2002
Auto-Answer=ON
Conference Group No.1
3. Speaker is automatically ON
Ext.1001
2. Call
4. Paging
Have to
The “Auto Answer” setting is a necessity!!!
Conference Group with Auto-Answer Before Ver.5
1. Ext.1001 holds a conference (*321#)
2. The PBX calls pre-programmed DECT-PS
3. All DECT PS on the conference group automatically answers.
Speaker phone is automatically “ON”.
4. Ext.1001 user can page.
Condition: All PS have to be set to “Auto-Answer” = ON.
1.Dial *321#
Ext.2003 Ext.2001 Ext.2002
Auto-Answer=ON
Conference Group No.1
3. Speaker is automatically ON
Ext.1001
2. Call
4. Paging
The “Auto Answer” setting is a necessity!!!
Conference Group with Auto-Answer Before Ver.5
1. Ext.1001 holds a conference (*321#)
2. The PBX calls a pre-programmed DECT-PS
3. All DECT PS on the conference group automatically answer.
Speaker phone is automatically “ON”.
4. Ext.1001 user can page.
Condition: System programming is required.
Regardless of “Auto Answer” = ON/OFF
Please set “Enable”
Conference Group with Auto-Answer New Program Item and Functionality
1.Dial *321#
Ext.2003 Ext.2001 Ext.2002
Conference Group No.1
3. Speaker is automatically ON
Ext.1001
2. Call
4. Paging
The “Auto Answer” setting is a necessity!!!
Conference Group with Auto-Answer Before Ver.5
1. Ext.1001 holds a conference (*321#)
2. The PBX calls a pre-programmed DECT-PS
3. All DECT PS on the conference group automatically answer. Speaker phone is automatically “ON”.
4. Ext.1001 user can page.
5. An answer (DECT-PS) is possible by pressing any keys.
Condition: System programming is required.
5. Press any keys
Please set “Enable”
Broadcast Mode Ability to Talk Auto-Answer Extension function
Answer Mode Talk Mode Disable Enable Disable Manual Answer Both way Disable Enable Enable Auto-Answer Both way Enable Disable Disable Manual Answer One way Enable Disable Enable Auto-Answer One way
Enable Enable Disable Manual-Answer One way → Press any key → Both way
Enable Enable Enable Auto-Answer One way → Press any key → Both way
Conference Group with Auto-Answer New Program Item and Functionality
1.Dial *321#
Ext.2003 Ext.2001 Ext.2002
Conference Group No.1
3. Speaker is automatically ON
Ext.1001
2. Call
4. Paging
This function also works on a D-PT.
Conference Group with Auto-Answer TDE/NCP Ver.5
1. Ext.1001 holds a conference (*321#)
2. The PBX calls a pre-programmed D-PT
3. All D-PT’s on the conference group automatically answer. Speaker phone is automatically “ON”.
4. Ext.1001 user can page.
Regardless of “Auto Answer” = ON/OFF
ONE TOUCH BUSY OVERRIDE
KX-TDE/NCP Version 5
Ext.2002
1- Ext.2001 is talking to an external person on SCO-1. 2- Ext.2002 press the SCO-1 button → Busy Tone 3- Ext.2002 press “3” or “OVER” for overriding the call.
Ver.5 (System option = ON) 1- Ext.2001 is talking to an external person
on SCO-1. 2- Ext.2002 press the SCO-1 button →
Overriding the call.
Ext.2001
1- Talking
Default : Disable
New Program Item
One Touch Busy Override Before Ver.5
CO
TENANT BASED ARS KX-TDE/NCP Version 5
Tenant-B UK
Company
International call Provider :BT
Tenant-A Japanese Company
International call Provider :KDDI
Customer needs a tenant base ARS reading table.
Tenant based ARS Before Ver.5 ARS function
All ARS reading tables are all for tenants,
Customer Request function (Sample) One PBX is shared with two or more companies. The companies have a contract with different telephone carriers.
Japanese company has to use KDDI for international call.
→ Dial +1 (USA call) → KDDI Line
UK company has to use BT for international call.
→ Dial +1 (USA call) → BT Line
KDDI BT
TDE600 Applied ARS Leading Digits Table Tenant 1 2 -- 19 20 21-32 Leading Digits Table 1-50 51-100 -- 901-950 951-1000 1-1000
Tenant Base
If the tenant ARS mode is selected to “Enable”,
TDE100/200/NCP Applied ARS Leading Digits Table Tenant 1 2 -- 7 8 - Leading Digits Table 1-50 51-100 -- 301-350 351-400 401-1000 (Not used)
Tenant based ARS TDE/NCP Ver.5
TDE-NCP version 5 supports tenant Independent ARS table.
TDE600 Applied ARS Leading Digits Table Tenant 1 2 -- 19 20 21-32 Leading Digits Table 1-1000
If the tenant ARS mode is selected to “Same as System Setting”, the PBX checks “8-1 System Setting”, applied ARS Leading Digits Table is as follows.
TDE100/200/NCP Applied ARS Leading Digits Table Tenant 1 2 -- 7 8 - Leading Digits Table 1-1000
Tenant based ARS TDE/NCP Ver.5
IMPROVED SERVICE OUT FUNCTION
KX-TDE/NCP Version 5
“Extension dial lock” : Ver.4/5 “DND” : Ver.4/5 “Display Lock” : Ver.5
Need the extension PIN
Other user cannot see call log and cannot listen to SVM message.
Improved Service Out Function Before Ver.5 Service Out status
“Extension dial lock” and “DND” are assigned automatically by “Service Out” operation. Therefore other users can see the call log and listen to the SVM message.
TDE/NCP Ver.5 Service Out status
“Extension dial lock”, “DND” and “Display Lock” are assigned automatically by “Service Out” operation.
Improved Service Out Function How to un-lock
NB: Input an extension PIN (Default: Blank) before use this function.
CLIP WHEN VM TRANSFER KX-TDE/NCP Version 5
CO
Ext.2001
1. Call
Ext.1001
PBX-1
PBX-2
System Programming 2.9 System Options → Option 4
CLIP:4771111
2. Transfer
Centralized VM
CLIP:4771111 VM Ext. Number
CLIP when VM Transfer Before Ver.5
When a VM transfers a CO call to a remote extension, The CLIP information form the VM is dependant upon the system programming.
VoIP-Net
Note: Ext.1001 (Local extension) receives always CLIP: 4771111, regardless of programming.
CLIP when VM Transfer TDE/NCP Ver.5
The remote extension receives always the CO CLIP, regardless of the system programming.
CO
Ext.2001
1. Call
Ext.1001
PBX-1
PBX-2
System Programming 2.9 System Options → Option 4
CLIP:4771111
2. Transfer
Centralized VM
CLIP:4771111
VoIP-Net
CLIP:4771111
Option Bit: 0C-5 0C-5=Disable: TDE/NCP Ver.5 (Default) 0C-5=Enable: Before TDE/NCP Ver.5
CLIP when VM Transfer TDE/NCP Ver.5
If a customer likes the previous function, please change the option bit 0C-5 to “Enable”
INCOMING CALL LCD KX-TDE/NCP Version 5
Incoming Call LCD Before Ver.5
If a caller name or ID / DID name / CO line number is displayed on PT LCD. They can be switched by the “Transfer” key or the “INFO” soft key. If the user presses the button by accident, this can become confusing, because last mode is stored and displayed, when the next call arrives.
TDE/NCP Ver.5
TDE-NCP Ver.5 does not the save display mode, even after PT operation. - Display switch operation itself is kept. - Display mode can be assigned using PCMC. - “Automatic save after PT operation” is controlled by the PCMC system reserved bit. This is now default and new specification for this function.
Default (Disable)
Option Bit: 06-5 06-5=Disable: TDE/NCP Ver.5 (Default) 06-5=Enable: Automatic save after PT operation
Incoming Call LCD TDE/NCP Ver.5
IMPROVED ICD GROUP CALL LOG
KX-TDE/NCP Version 5
ICD-G
TDE/NCP Ver.5 TDE-NCP Ver. 5 records ICD group call, when the call is overflowed to VM.
Ext.1001
1. Call 2. OVF
3. VM Answer
4. Disconnect
ICD-G Log Key
Improved ICD-G Call Log Before Ver.5
1- If an incoming call goes to an ICD-G.
2- If a member of ICD-G does not answer, the call is OVF to a VM,
3- The VM answers the call.
4- If the caller disconnects the line before the VM starts the message recording.
→There is No call log on the system (ICD-G Log key or VM).
CO
Default: Disable
1. Call 2. OVF 3. VM Answer 4. Disconnect (Before VM
message recording)
1. Call 2. OVF 3. VM Answer 4. Disconnect (After VM message
recording)
1. Call 4. Disconnect (Before OVF)
Disable No Call Log No Call Log Call Log
Enable Call Log Call Log Call Log
If the OVF destination is a VM
Improved ICD-G Call Log TDE/NCP Ver.5 New Option
ICD-G
Ext.1001
1. Call 2. OVF
3. VM Answer
4. Disconnect
ICD-G Log Key
CO
Default: Disable
If the OVF destination is a VM
Improved ICD-G Call Log TDE/NCP Ver.5 New Option
ICD-G
Ext.1001
1. Call 2. OVF
3. VM Answer
4. Disconnect
ICD-G Log Key
CO
1. Call 2. OVF 3. D-PT answer 4. Disconnect
1. Call 2. OVF 3. D-PT does not answer 4. Disconnect
1. Call 4. Disconnect (Before OVF)
Disable No Call Log Call Log Call Log
Enable Call Log Call Log Call Log
IMPROVED VM CONNECTION
KX-TDE/NCP Version 5
Disable
1. Call AA
Service
Enable
1. Call Mailbox Service
1. Call Mailbox Service
ICD-G
AA Service
2. OVF 1. Call
Customer Request function
ICD-G OVF → AA Service
Extension Intercept →Mailbox
Improved VM connection Before Ver.5
There is one optional item to control the VM function, when an incoming call is intercepted (OVF) to the VM from the Ext. (ICD-G).
2. Intercept
2. Intercept
2. Intercept
ICD-G
1. Call AA
Service
2. Intercept
1. Call Mailbox Service
2. Intercept
1. Call Mailbox Service
2. Intercept
ICD-G
AA Service
2. OVF 1. Call
Improved VM connection TDE/NCP Ver.5
Two optional items to control VM function, when an incoming call is intercepted (OVF) to VM from the Ext. (ICD-G).
Disable
Enable
Disable
Enable
This option has an effect for external calls only, not for internal calls.
- T.38 DISABLE MODE IS SUPPORTED. - FORWARD CLIP (A-NUMBER) FOR SIP TRUNK - REFER TRANSFER IS SUPPORTED FOR SIP TRUNK - P-ASSERTED-IDENTITY HEADER IS SUPPORTED FOR SIP TRUNK - CODEC PRIORITY NOTIFICATION FROM SIP NETWORK - IMPROVES FAX CONNECT ABILITY - REDUNDANCY FUNCTION IS SUPPORTED FOR SIP TRUNK - DELETE ALPHABET CALLER-ID
Improvement features of SIP Trunk
New Program Item
Improves SIP Trunk feature (TDE/NCP Ver.5)
T.38 disable mode
Before Ver.5
For out going FAX We can select “enable”/”disable” T.38 function.
For incoming FAX We cannot select “enable”/”disable” T.38 function.
→ When un-compatible T.38 incoming FAX arrives the system, the FAX connection will be failed.
TDE-NCP Ver.5
For out going FAX We can select “enable”/”disable” T.38 function.
For incoming FAX We can select “enable”/”disable” T.38 function.
→ Un-compatible T.38 incoming FAX → Please set “Disable” → G.711 mode
1. Call TDE/NCP
CLIP:8821111 C-FWD to CO
CLIP:4771111 INVITE: CLIP Information ?
Improves SIP Trunk feature (TDE/NCP Ver.5)
Forward CLIP (A-number)
When the SIP trunk incoming call is forwarded to a mobile network through the SIP trunk, incoming CO callers CLIP (A-number) can be sent using the diversion header feature.
SIP-Provider
Before Ver.5
CLIP We can select the extension CLIP or the Caller CLIP.
TDE-NCP Ver.5
CLIP We can select the extension CLIP or the Caller CLIP.
And the PBX sends the Caller CLIP by the diversion header element (Select System Option).
New Program Item
Improves SIP Trunk feature (TDE/NCP Ver.5)
Forward CLIP (A-number) (New Program Item)
NB: SIP IOT is strongly required before this is set to “Enable” !
SIP-Provider
SIP-Provider
3.Connect
TDE/NCP
Ext.1001
1. Talking TDE/NCP
Ext.1001 2. Refer Transfer
4.Voice paths are released
-Attended Transfer -Blind Transfer
External Caller
External Caller
Improves SIP Trunk feature (TDE/NCP Ver.5)
Refer Transfer
When a TDE/NCP Ver. 5 extension makes a call, the caller can transfer the call to another external party through the SIP trunk by using the Refer Transfer feature.
Blind Transfer
Attended Transfer
Improves SIP Trunk feature (TDE/NCP Ver.5)
Refer Transfer (Operation differences)
New Program Item
Improves SIP Trunk feature (TDE/NCP Ver.5)
Refer Transfer (New Program Item)
NB: SIP IOT is strongly required before set to “Yes” !
SIP-Provider
TDE/NCP
Ext.1001 External Caller
2. Refer Transfer to Ext.1002
1. Talking
Improves SIP Trunk feature (TDE/NCP Ver.5)
Refer Transfer (Condition)
TDE/NCP Ver. 5 does not support a refer transfer request from the SIP provider.
SIP-Provider
INVITE Message Header (TDE/NCP Ver.5)
Make a call TDE/NCP
INVITE Message
Improves SIP Trunk feature (TDE/NCP Ver.5)
P-Asserted-Identity Header
TDE/NCP Ver.5 supports the P-Asserted-Identity header.
New Program Item
Improves SIP Trunk feature (TDE/NCP Ver.5)
P-Asserted-Identity Header (New Program Item)
NB: SIP IOT is strongly required before set to “Yes” !
New Program Item
Enable: SIP network CODEC Disable: PBX CODEC (Default)
Improves SIP Trunk feature (TDE/NCP Ver.5)
CODEC Priority Notification
Before Ver.5
When the PBX receives a SIP call from the SIP network, the PBX CODEC selection is first priority against SIP network request.
TDE/NCP Ver.5
CODEC priority is selectable (PBX CODEC or SIP network CODEC )
System Programming
2.9 System Options → Option 2
SIP-Provider
FAX Call
TDE/NCP
DSP
Support Super G3 DSP NLP setting DSP Echo setting
Before Ver.5 No No changed No changed
TDE/NCP Ver.5 YES OFF (Automatic) OFF (Automatic)
DSP NLP setting DSP Echo setting
Before Ver.5 No changed No changed
TDE/NCP Ver.5 OFF (Automatic) No changed
G3 FAX
Support Super G3 FAX
Improves SIP Trunk feature (TDE/NCP Ver.5)
Improves FAX Connect ability
TDE/NCP Ver.5 supports Super G3 FAX function over SIP trunk.
SIP-Provider
SIP-Provider
Redundancy Case-1
SIP-Server-2
TDE/NCP SIP-Server-1 1. Call
Redundancy Case-1
SIP-Server-2
TDE/NCP SIP-Server-1 1. Call
Improves SIP Trunk feature (TDE/NCP Ver.5)
Redundancy Function
TDE/NCP Ver.5 supports the redundancy function in two cases.
SIP-Provider
SIP-Server-2
TDE/NCP SIP-Server-1 1. Call
New Program Item
Timer Value=0: Disable Redundancy Timer Value ≠0: Enable Redundancy
Improves SIP Trunk feature (TDE/NCP Ver.5)
Redundancy Function (New Option Program)
Redundancy Case-1
NB: SIP IOT is strongly required before set to “Yes” !
New Program Item
Disable: Disable Redundancy Enable: Enable Redundancy
Improves SIP Trunk feature (TDE/NCP Ver.5)
Redundancy Function (New Option Program)
Redundancy Case-2
SIP-Provider
SIP-Server-2
TDE/NCP SIP-Server-1 1. Call
NB: SIP IOT is strongly required before set to “Yes” ! It should not be “0”
SIP-Provider
Make a call
TDE/NCP
INVITE Message CLIP: 0924771234aaaaa
Delete data
CLIP 0924771234
Improves SIP Trunk feature (TDE/NCP Ver.5)
Deletion alphabet Caller-ID
When an alphabet characters are contained within the CLIP information, in the INVITE message, these alphabet character’s are deleted.
SIP PHONE FEATURE KX-TDE/NCP Version 5
Before Ver.5
TDE-NCP does not support verification code feature for SIP phone.
TDE/NCP Ver.5 TDE-NCP version 5 supports verification code feature for SIP phone.
SIP Phone Feature
PCMC ID LOCK (RU/UA MODEL ONLY)
KX-TDE/NCP Version 5
Model Registration Specifications
TDA100D 16-digit ID is required to PCMC. ID is provided to only authorized dealer from Panasonic CIS. ID for TDA100D and ID for TDE-NCP are different.
ISDN/DECT/TIE programming is not allowed before registration.
TDE-NCP Version 5
All programming is not allowed before registration. In Russia a dealer has to disclose the PBX password to the user by law . The user can inform the password to an unauthorized dealer, if maintenance fee is cheaper. However the unauthorized dealer cannot program PBX from version 5.
NS1000
The activation key is required in the PBX. The activation key is provided from PSN key management system. The activation key is only provided to authorized dealer s free of charge. Validity of the activation key is 6 months.
PCMC ID Lock TDE/NCP Ver.5
TDE-NCP version 5 supports PCMC ID lock for NCP500-1000RU/UA, TDE100-200RU/UA and TDE600RU/UA.
PC MAINTENANCE CONSOLE (PCMC) FOR TDE-NCP
KX-TDE/NCP Version 5
Please use U-PCMC Ver. 7.2.x.x
KX-TDE600 Ver. 7.2.x.x or later
KX-NCP500/1000 Ver. 7.2.x.x or later
KX-TDE100/200 Ver. 7.2.x.x or later
PCMC for KX-TDE/NCP Ver.5.
THANK YOU VERY MUCH FOR YOUR ATTENTION!