WARNING: Harley-Davidson® Personal Safety Wearproducts are not intended for use when riding a motorcycle.Improper use of these products may result in seriouspersonal injury or death.
▲!
Harley-Davidson® Personal Safety Wear products cannot be sold to authorized Harley-Davidson dealers, retailers or mass merchandisers.
HRD-HD1100Black/Orange Frame - Clear Lens $17.45
HRD-HD1101Black/Orange Frame - TSR Gray Lens $18.95
QPL-1199Lower Control Arm Triple Action Tool• For C-V Axle and Strut repair• One man operation, fast and safe• Makes strut replacement easy• Removes ball joints without damage• Re-installs lower control arm
Medium Strength BLUEThreadlocker• Compares to LOCTITE® 242®
• For 1/4" to 3/4" (6 to 20mm) fasteners
• 110 lbs break strength and 43 lbsfor prevail torque
• Temperature range: -65°F to 300°F• Removable strength
High Strength RED Threadlocker• Compares to LOCTITE® 271®
• For fasteners up to 1" (25mm)• 250 lbs of break strength and 275
lbs for prevail torque• Temperature range: -65°F to 300°F• Removable strength
QPL-14010 - 10 ml
QPL-14050 - 50 ml
QPL-14025 - 250 ml
QPL-12110 - 10 ml
QPL-12150 - 50 ml
QPL-12125 - 250 ml
LOCTITE®, 242®, AND 271®,ARE REGISTERED TRADEMARKS OF: HENKELCORPORATION, U.S.A.
RFX-7121100Professional Dual Adhesive System• Bonds most materials instantly, including: rubber,
glass, copper, aluminum, steel and most plastics.• The welding powder is used to repair or fill all types of holes/cracks• Bonds in seconds, will not dry out in container• RapidFix can be sanded, ground, drilled and painted instantly• Dries crystal clear
QPL-762864Cable Tie Tool• Automatic cut-off• Adjustable tensioning• Use with 18lb - 50lb
cable ties
QPL-BM8315FRONT WHEEL DRIVEHub Puller• 10 lbs slide hammer• Includes 2 adapter plates• For domestic and asian cars
SG-198301/4" Super Duty Riveter with 5-3/4" Extended Nose Reach
SG-2392090° Boot, In-Line IgnitionSpark Checker
SG-23900In-Line Ignition Spark Checker
SG-23000Universal AutomotiveTest Lead Kit48" long test leads.
SG-23150Perma-Coil Jumper LeadsExtends to 10', retracts to 2'.
SG-23970In-Line Spark Checker Kit for Recessed Plugs• For virtually all domestic and
imported cars, SUV’s andtrucks
• Tests newer vehicles withrecessed spark plugs
• Provides information notavailable with OBD II codereading devices — pinpointsif there is a spark plug, plugwire, mechanical, fuel injec-tion or electrical problem
• PACKAGED IN A BOX
SG-18900Professional Ratcheting Terminal Crimper10 to 22 gauge.
SG-18920Ratcheting TerminalCrimping KitIncludes 5 quickly interchange-able dies for virtually all uses.
SG-23950Coil On Plug Ignition Spark CheckerQuickly troubleshoot the contemporary “coil on plug”ignition systems found on GM,Chrysler, Ford and import vehicles
SG-18930Ratcheting Terminal Crimperfor Weatherpack Terminals 10 to 22 gauge.
SG-18960Quick Change Ratcheting Terminal Crimping KitIncludes 7 die sets for the mostpopular automotive terminalcrimping applications.
SG-27300Heavy Duty Circuit Testerwith 12' Retractable Wire & Battery ClipFor 6 and 12 Volt systems
SG-28100Heavy Duty Automotive Logic ProbeTest high and low voltages on 6, 12 and 24 volt systems, dual colour led.
SG-270006 & 12 Volts Heavy DutyCircuit Tester
SG-36300Noid Light SetQuickly tests electronic fuelinjection signals. Supplied withlights to check GM TBI, BoschPFI, Ford TBI, Geo TBI andGM SCPI.
SG-36250Multi-Port Fuel InjectionPressure Tester Kit forDomestic & Foreign VehiclesTests the fuel pressure on virtually all domestic & foreignvehicles equipped with multi-port fuel injection.
SG-34580Deluxe Automatic Transmis-sion & Engine Oil PressureTester with 2 Gauges• 0-600 PSI & 0-50 PSI gauges.• Includes adapters for
domestic and import vehicles.
SG-36350In-Line Spark Checker Kit forRecessed Plugs, Noid Lightsand IAC (Idle Air Control) Test Lights
FREE! #SG-29000(Heavy Duty Mini Circuit Tester) with purchase of #SG-36350
FREE! #SG-29000 withpurchase of #SG-18960.
$18.95$19.95
$47.95
$59.95 $7.25
$59.95
$6.95
$49.95
$19.95
$18.95
$28.95
$119.95
$8.95
$41.95
$114.95
$8.95
$36.95
$7.25
$16.95
$129.95
$79.95
89 1er janvier au 24 février 2012 • January 1 to February 24, 2012
SG-87810Upholstery Clip Removal Tool
SG-61800Strut AlignmentLevel
SG-82350Door Aligner ToolAlign car and truck doors witheither bolted or welded hingesin seconds by using leverage.
SG-62200Single Turning Action Coil Spring “Clamp It”
SG-180003/8" Rotary Spot Weld Cutter
SG-142904 Piece BrassPin Punch SetContains:1/8" x 4", 3/16" x 4",1/4" x 4" and 3/8" x 6"pin punches.
SG-919502" Wide Pneumatic Scraper• .401" Parker shank• Blade has slight offset for
easy use
SG-142703 Piece Brass Drift Punch SetContains:1/2" x 7", 5/8" x 7"and 3/4" x 8"drift pin stylepunches.
SG-1381015" Extra-Long Hooker
SG-87675Door Hinge Spring ToolUse this one tool to service latemodel GM cars and light trucks (with larger diameter springs).
SG-14950ReversibleImpact Driver Set• Use to loosen
and tightenscrews, nutsand bolts
• Includes 8standard andlong lengthinterchange-able bits
SG-81500Junior SluggerDent Puller and Slide Hammer
SG-6637010 Lb Slide Hammer & Pullers for FrontWheel Hubs andRear Axles• Pullers fit 4, 5 and 6 bolt
patterns for use on most domestic and import cars and light trucks• Axle and hub pulling adapter accepts other
5/8"-18 female threaded pulling attachments
SG-87900Windshield RemovingTool (Cold Knife)
SG-138507 Piece Universal Hook & Pick Set
SG-138008" Long HookerIdeal to remove radiator hoses, pull cutter pins andother jobs.
SG-1384011" Great Big Hooker, Jr.• Special hook design for easy
removal of cotter pins andradiator hoses
SG-94950Arbor For Cut-Off WheelsFor 1/4" & 3/8" center holes.
SG-94400Quick Change Chisel Retainer
SG-17280Spray GunCleaningKit
SG-98025All Brass Air Regulator 1/4'' M x 1/4'' F NPT.
SG-99150Lever Action Blow GunIncludes 5 nozzles.
SG-879403 Position Windshield and Window Sticker Scraper
SG-17380Disc Brake Caliper Brush• Removes brake dust and dirt
from caliper shaft
SG-18500Spark Plug CleanerCleans any spark plug quickly and effortlessly with internally controlled abrasiveblasting.
SG-65140Tire Tread Depth Gage• Sliding gage measure in
inches and millimeters (3 sides measure 0 - 1" in1/32" increments and 0 -25mm in 1mm increments).
SG-3402012mm & 16mm Compression TestAdapter for Ford TritonEngines• Use on the 16mm-1.50 male
threads on 3 valve Triton engines2004-2008 5.4L Ford F-150 and2005 4.5L Ford Mustang
• The 12mm-1.25 male threads arefor use beginning with model year2009 Triton 4.6L, 5.4L and 6.8Lengines
$7.95
$29.95
$54.95
$4.95
$59.95
$10.95
$29.95
$17.95
$29.95
$44.95
$14.95
$19.95
$24.95
$32.95
$134.95
$15.95
$34.95
$9.95
$10.95
$5.95
$17.95
$36.95
$10.95
$5.95
$11.95
$6.95
$7.95
90 1er janvier au 24 février 2012 • January 1 to February 24, 2012
FREE! #MAY-40160 (48" x 3/4" Pry Bar) withevery purchase of #MAY-61356.
FREE! #MAY-60008 with purchase of#MAY-28630.
FREE! #MAY-62250 (PilotPunch Set) with pur-chase of #MAY-29910.
FREE! #MAY-60004, with purchase of#MAY-61050.
MAY-61306 3 Piece Line Up Pry Bar Set• Pointed end for
aligning, angled chisel end for extra leverage when prying• Contains: 14" and 20" line-up pry bars, 16" rolling head pry bar
MAY-620154 Piece Bearing Race Punch Set• Contains: 7/16" x 6", 1/2" x 10", 9/16" x 14" and 5/8" x 20"
Dominator® Pry Bars• Capped end for striking• Shaft goes through handle for prying power
MAY-613553 Piece Dominator®
Curved Screwdriver Pry Bar Set• Contains 12", 17" and 25"• Capped end for striking
MAY-613563 Piece Dominator®
Pry Bar Set• Contains 18", 24" and 36"• Capped end for striking
MAY-4016048" x 3/4"
MAY-4016258" x 3/4"
MAY-4016645" x 1"
MAY-4016444" x 7/8"
MAY-4002460" Long Line-Up Pry Bar• Pointed end for aligning work• Angled chisel end for extra leverage when prying
from 1/8" to 2" in diameter• Ergonomic pistol grip rubber
handle absorbs the shock fromthe impact of the hammer
• Includes mandrel and springloaded centering point
$14.95
$109.95
$154.95
$75.95
$469.95
$109.95
$59.95
$82.95
$148.95
$109.95 $119.95 $139.95$119.95
$49.95
$16.95
$49.95
$16.95
$27.95
$59.95
$69.95
$159.95
$45.95
$139.95
$74.95
MADE IN
FRANCE
MADE IN
FRANCE
MADE IN
FRANCE
MADE IN
FRANCE
91
$40.95
$24.95
$47.95
$259.95
$95.95
$139.95
$54.95
1er janvier au 24 février 2012 • January 1 to February 24, 2012
LIS-13800Water Pump Sprocket Holder for GM Ecotec EnginesHolds the timing chain and gear inplace while removing or installingwater pump.
LIS-54200For Cummins & Detroit DieselEngines4-5/16'' to 4-3/4''
LIS-54300For Caterpillar Engines5-1/4'' to 5-3/4''
“Swivel Grip” Truck Filter Wrenches
LIS-507502.25" to 4"
Oil Filter Pliers
LIS-509503-5/8" to 6"
LIS-433007 Piece Pneumatic Fan Clutch Wrench Set to Remove & InstallFits Ford, GM and Chrysler.Includes: 36mm, 1-1/2", 1-9/16",41mm, 42mm, 1-7/8" and 2".
LIS-2628010-Piece Master Female Torx Socket SetFrom E5 to E20, in 1/4", 3/8" and1/2" drive sizes.
LIS-260008 Piece Tamper Resistant Torx Bit Set• 1/4" Hex insert bits with 1/4" drive
bit holder. • T-10 to T-40.
LIS-70500Tap Socket SetSet of 8 sockets fits all numbers, fractional and metric tapsfrom 1/8" - 1/2" (12mm).
LIS-709403 Piece Tap Socket Set• For large sizes. • For 5/8", 11/16" 3/4", 16mm and
18mm.
LIS-34400Exhaust/Tailpipe StretcherStretches pipes including stainlesssteel from 1-5/8'' to 2-7/16''.
LIS-38350Exhaust Removal PliersWorks on all domestic and importcar and truck exhaust systems thatuse the rubber hanger supports.
LIS-46600Universal Inner Tie RodWrenchRemoves/installs inner tie rodsequipped with a completely roundend socket up to 1-31/64". Also fits inner tie rodsockets with flats.
LIS-457507 Piece Inner Tie Rod Tool Set1-1/4'', 1-1/2'', 1-3/16'', 1-5/16'', 1-7/16'', and 33.6mm.
LIS-41500Pickle Fork KitFor separating ball joints, tie rods,Pitman arms and other uses.
LIS-41400Stepped Pickle Fork KitStep design helps keep tool frombouncing back. For separating balljoints, tie rods, Pitman arms andother uses. Includes 1-1/8", 15/16",11/16" forks, pneumatic driver andhandle.
LIS-18980PneumaticU-Joint DriverQuickly removes the U-joint cap (up to 1-5/16" in diame-ter) from the drive shaft on mostrear wheel drive vehicles.
LIS-59000Ratcheting Serpentine Belt Tool Includes 13, 14, 15, 16, 18mm, andalso 19mm socket for Honda andToyota applications, extension, 3/8"& 1/2" square drives.
LIS-38210Hub Remover Kit for DodgeSeparates the frozen hub assemblyfrom the steering knuckle on Dodgevehicles.
LIS-54640Pneumatic Tie Rod Rattler• Loosens seized bolts and clamps
on tie rods for removal or adjust-ment. Use with an air hammer.
• Works especially well on Ford F-Series trucks and SUVs.
LIS-68130Wheel Weight Tool• Removes, trims and installs clip-
on wheel weights• Also includes lever and offset flat
tip for removing wheel covers
LIS-69000Dual Drive Stubby Metric Hex Bit Set• 1/2" / 1" drive• 10, 12, 14 and 17mm
LIS-17350Exhaust/TailpipeStretcher KitStretches pipesincluding stainlesssteel from 1-5/8" to4-1/4".
LIS-46800Master Inner Tie Rod Tool Set29mm, 1-3/16", 1-1/4", 32.5mm, 1-5/16", 33.6mm, 1-3/8", 1-7/16", and 1-1/2".
LIS-43600Universal Fan Clutch Wrench Set• For use on most popular
applications• Hooked wrench will hold bolted on
water pump pulleys• Double-sided spanner style
wrench will hold pressed on pul-leys on many GM, Jeep andDodge vehicles
• Double-ended turning wrench with36mm and 47mm/1-7/8 openingsand 1/2" square drive holes foruse with a hand ratchet or abreaker bar
$189.95
$229.95
$30.95
$79.95
$34.95
$129.95
$36.95
$19.95
$44.95
$38.95
$31.95
$14.95
$13.95
$26.95
$42.95
$47.95
$64.95
$30.95
$72.95
92
$8.95 $8.95
1er janvier au 24 février 2012 • January 1 to February 24, 2012
“Swivel Grip” Oil Filter Wrenches
End Cap Filter Wrenches
Brake Bleeder WrenchesLIS-109005/16" x 3/8"
LIS-109501/4" x 3/8"
LIS-53250Large4-1/8'' - 4-1/2''
LIS-53500Standard3-1/2'' - 3-7/8''
LIS-53700Small2-7/8'' - 3-1/4''
LIS-54400Extra Small2-3/8" - 2-5/8"
LIS-45100Brake Spring Tool
LIS-50600Single-Spring Brake Tool for GMReleases tension on large andsmall GM single spring brakesduring servicing.
LIS-54920Cap Style Filter Wrench SetIncludes ten 3/8" drive cap wrenches. Fits 95% of domesticand import cars.
LIS-28500Strap WrenchLoosen or tighten cylindrical or rectangular objects. Range from 1" to 6-5/8" round.
LIS-14440Water Pump Wrench for GM NorthstarRemoves and installs the waterpump assemblyon GM Northstar4.0L and 4.6Lengines.
LIS-63250Wide Range Filter WrenchFits filters from 3-1/8" to 3-7/8". Use with 3/8" drive.
LIS-63600Import Car Filter WrenchFits filters from 2-1/2" to 3-1/8". Use with 3/8" drive.
LIS-49000Truck Spring Cage Bolt SocketExtra deep 3/4" socket loosens thecage bolt to unlock air brakes ontrucks. Also removes the air brakebooster for replacement.
LIS-24300Speedy Brake Pad SpreaderCompresses brake pistons in seconds to makebrake pad replacement an easy job.
LIS-25750Dual Piston Brake Pad SpreaderCompresses dual brake pistons simultaneously.Makes dual piston pad replacementa simple job.
LIS-24400Disk Brake Pad SpreaderFor installing pads on most domestic & import cars and light trucks.
LIS-48400Import Car Brake Clip ToolRemoves and installs the brakeclip and nail on brake shoes inseconds.
LIS-34000Oil Filter Cap Wrench for DodgeFits threaded caps on newer DodgeV8 engines and some Jeep Liberty,Grand Cherokee and Commander.
LIS-57010Extra Small Filter Wrench2.375" – 2.625" (60.3 – 66.7mm)
LIS-51300Parking Brake AdjustingSpoon for Ford TrucksDouble-ended tool speeds starwheel adjusting on Ford F-150.Also works on F-250/F-350 superduty trucks with Dana 80 rearaxles.
LIS-51400Drum Brake Adjustment Tool for FordSpeeds star wheel adjusting on2001-2006 Ford Taurus, Windstarand Mercury Sable, and other drumbrakes with top-mounted adjuster.
LIS-1350041mm Water Pump Wrenchfor GM 1.6LWorks on 1.6L engines in 2004-cur-rent Chevrolet Aveo excluding 2009with variable timing engine and1999-2002 Daewoo Lanos.
Filter SizeItem # (mm) Flutes Price
LIS-54700 65 & 67 14
LIS-54720 80 15
LIS-54740 74 & 76 15
LIS-54760 76 14
LIS-54780 93 15
LIS-54800 93 36
LIS-54930 65 14For Toyota
LIS-5488017 Piece End Cap FilterWrench Master SetFor use on the most populardomestic and Import vehicles,including Toyota.
LIS-68210Injector Pressure Regulator Socket for Ford 6.0Land OtherDiesel Engines
LIS-29100Quick Quad PadSpreader• A quick way to spread brake pads
and compress disc brake pistonsfor pad replacement on single,double and quad piston calipers
• Simultaneously compresses allfour pistons on quad piston applications
• Can be used while caliper is onthe vehicle
LIS-60200Heavy Duty Strap Filter Wrench• Use with 1/2" drive to remove or
install filters and other objects upto 6-1/2" in diameter
• 3-5/8" long yoke fits into tightareas
$11.95
$35.95
$9.95
$9.95$11.95
$26.95
$23.95
$45.95
$54.95
$9.95
$9.95
$15.95
$14.95
$15.95
$15.95
$15.95
$17.95
$23.95
$23.95
$29.95
$54.95
$104.95
$12.95
$10.95
$11.95
$12.95
$6.95$6.95$6.95$6.95$6.95$6.95
$6.95
$6.45
$69.95
93
$39.95
$79.95
$24.95
1er janvier au 24 février 2012 • January 1 to February 24, 2012
LIS-58850Oil Pan PlugRethreading KitWorks on soft steel with 1/2",12mm & 14mm threads.
LIS-16000Small Engine Cylinder HoneRange: 1-3/4" to 2-3/4"
LIS-51450Harmonic Damper Pulley Puller• For Chrysler, GM, Mitsubishi and
Dodge
LIS-56150 Combination Flaring ToolIncludes all the adapters and toolsnecessary for single and double flaring (standard and metric) plusthe ISO (bubble) flare. Works onaluminum, copper and soft steeltubing. Not recommended for stain-less steel. LIS-39900
Master Disconnect SetContains 8 popular disconnect toolsfor A/C and fuel lines.
LIS-12800Master Pneumatic BearingRace & Seal Driver Set• Contains 11 drivers to fit
automobiles and trucks up to 1 ton
• Also includes 2 handles, one forhammering and a pneumatic han-dle for use with an air hammer
LIS-12980Bearing Race & Seal DriverMaster SetSet includes 9 drivers to fit most standard wheel bearings.
LIS-54150Battery Terminal & Wiper Arm PullerRemoves battery terminals andbolted on wiper arms.
LIS-22850Hose PinchersFor vacuum lines, fuel lines, etc.
LIS-11420Hose CutterCuts flexible hoses up to 1-1/4"
LIS-34550Handy Bearing PackerQuickly flushes out old grease andrepacks bearings with less mess.
LIS-296504 Piece Antenna Socket Set
LIS-30800CV Boot Clamp Plier For all ear-type clamps & GM FWD outboard CV joints.
LIS-37000AC/Fuel Line Disconnect Tool SetDisconnects the spring lock couplings on Ford and Chrysler air conditioning line.
LIS-399603/8" & 1/2" Transmission Oil Cooler Line Disconnect for FordFor 2003 and later Ford V8 Explor-er, 2004 and later Ford F150 andCadillac CS, Ford Super DutyTrucks, F250, F350 and F450.
LIS-22710Disconnect Set for Jiffy-Tite® ConnectorsDisengages the line from thefittings without removal of theclip. Fit the most popular Jiffy-tite fittings. Includes 3/8", 1/2", 5/8"39% and 5/8" 30% Jiffy-Tite®
disconnect.
LIS-1745012" Drill Extension• Use in any 3/8" or larger drill
chuck for an additional 12" ofreach
• Will hold bits up to 3/8"• Works well to drill out broken man-
ifold studs on Ford Triton engines
LIS-19860Tire Deflator Set for TPMS Valve StemsQuickly evacuates air from tireswithout removing the valve core.
LIS-41270Input Shaft Alignment Tool• Works on manual and electronic
shift transmissions in heavy dutytrucks with 1-3/4" and 2" splinedshafts.
LIS-42400Air Line Disconnect Set• Disconnects quick connect push-
in connectors found on heavy-dutytruck air systems and more
• Set comes with 5 popular sizes:1/8"-5/32", 1/4", 3/8", 1/2" and 5/8"
LIS-39660Transmission Oil Cooler LineScissors 3/8" x 1/2" for Fordand Cadillac Vehicles• Use 3/8" size for 2003-2010 Ford
V8 Explorer, 2004 and later FordF150 and Cadillac CS
• Use 1/2" size for Ford Super DutyTrucks, F250, F350 and F450
$59.95
$134.95
$25.95
$52.95
$129.95
$22.95
$7.45$104.95
$129.95
$24.95
$16.45
$84.95
$32.95
$9.95
$9.45$23.95
$229.95
$229.95
$11.95
$39.95
94
$24.95
1er janvier au 24 février 2012 • January 1 to February 24, 2012
LIS-65600BrokenPlugRemover for Ford 3 Valve• Removes broken spark plugs
from 2004 and newer Triton 3valve per cylinder engines, (acommon problem)
LIS-22800Wheel Stud InstallerEasily installs new wheel studs onmost all automotive andlight duty truck wheels,foreign and domestic.
LIS-12230Oxygen Sensor Thread ChaserCleans threads on oxygen sensor holes.
LIS-55700Master Fuel Injection Test SetTests GM, Ford, Chrysler, Honda,Acura, Toyota, Bosch CIS and L-Jetronic.
LIS-28100Torque AngleMeter
LIS-32900Heavy DutyCircuit Tester/JumperA 2-in-1 tester that test circuits up to 12 Volts and works as a jumper wire for power or ground.
• Installs a new spark plug threadinsert in original thread location
• Includes three insert sizes: 5/16",7/16" and 11/16"
LIS-60610Relay TestJumper Kit IISet includes fourjumpers to fitmany popularrelays onHonda, Nis-san, Toyota,newer Ford andGM mini microrelays as well as Internationaltrucks.
LIS-69200Test Lead Kit for Relay Test JumpersUse with Nos. 56810 or 60610 toconnect relay test jumper to amultimeter.
LIS-395101/2" Drive 12 Point, 30mm Axle Nut SocketRemoves and installs axlenuts and automatic transmission tail output shafts.
LIS-28640Ultimate Circuit Tester Kit• Tests up to 28 Volts
LIS-32150Power/Ground OutletProvides a convenient electricalground and power source from thevehicle.
LIS-51750Adjustable Spark Plug Wire PullerJaws adjust to 5 positions.
LIS-22500Thermostat Gasket Cleaner
LIS-55150Air Bag Release Tool for GMEasily release SIR module retentionsprings on GM cars, minivans andlight trucks
LIS-36880Dual OverheadCam (DOHC) Lock ToolLocks camshaft sprockets in place during belt or chain replacement.
LIS-62300Universal Strut ToolFor import and domestic cars.
LIS-147003/8" Drive Oil Filter Socketfor 2.2L GMRemoves and installs oil filters on 2.2 liter GM Ecotec engines. Thelow profile 1-1/4" socket is speciallydesigned for operating clearance.
LIS-145003/8" Drive Oil/Fuel Filter Socket for 6.0L Ford DieselThe low profile socket fits both the35mm and 36mm fuel and oil filters.Not for use with an impact wrench.
LIS-75500Combustion Leak DetectorIndicating fluid changes from blue toyellow when exposed to combustiongases in radiator.
LIS-56810Relay TestJumper Kit• Set of four
relay testjumpers make testing relays oflive circuits quick and easy.
• Jumpers fit the most popular sizerelays on domestic and importvehicles
LIS-20000M12x1.25 Limited AccessSpark Plug Chaser• For use on 2nd generation Ford
Triton engines 2008 and newer.• Also for use on Mercedes Benz
most V6 and some V8 modelsnewer than 2006. Toyota Scion1.8L 2008 and newer. Nissan 2.0L2007 and newer.
LIS-30610Heavy Duty Circuit Testerwith Grounding Adapters• Tests circuits up to 12 Volts
LIS-396501/2" Drive 12 Point, 39mmAxle Nut Socket for ToyotaRemoves and installs axlenuts on 4WD axlehubs.
LIS-63000Fuel Tank Lock Ring Tool• Removes and installs plastic fuel
tank lock rings from 4" to 7-1/4"without damage
LIS-60660Deluxe RelayTest Set• Includes 8
jumpers to fitmost popularrelays
• Includes test lead kitand relay puller pliers
$8.95
$9.95
$7.95
$16.95
$20.95
$29.95
$39.95
$39.95
$22.95
$459.95$95.95
$69.95
$38.95
$17.95
$28.95
$22.95
$69.95
$7.45
$69.95
$179.95
$19.95
$119.95
$39.95
$26.95
$42.95
95 1er janvier au 24 février 2012 • January 1 to February 24, 2012
LIS-19852Truck and Trailer Wheel PanCatches oil from wheel hubs afterremoving cap. Will not warp if oil iswarm.
LIS-111028 Gallon Plastic Oil Lift Drain onWheels• Large 15" funnel
with strainer• Range: 37" to 75"
LIS-1743218 Gallon Oil Lift Drain• Large 15" funnel
with strainer• Range: 36-1/2" to 77"
LIS-197721 Quart (32 oz.) Spray Bottle• For use with light oils, solvents,
and detergents• Translucent plastic
LIS-19822Tire & Tube Test Tank31" x 12" x 12".
LIS-24610Spill-Free Funnel Set with AdapterIncludes threaded cap and adapterfor newer GM “threaded style” radi-ator openings. Eliminates trappedair pockets. Four adapters fit most domestic and import cars and light trucks.
Hog Ring PliersUsed for upholstery work onmost domestic & import cars.
KD-3321Fuel LineQuick Disconnect Tool
KD-145Hose Clamp Plier
KD-2078Universal Overhead Valve Spring Compressor
KD-3729Push Pin Removal PlierTool lifts the centerpin and pulls anchor in one simple step. Anchors common on Honda, Toyota, GM, Ford,Chrysler and many other latemodel vehicles.
KD-124Remote Control Starter Switch
KD-37954 Gallon Capacity Brake Bleeder TankFor use with DOT 2, 3, 4 and 5brake fluids only.
KD-2833Engine Cylinder HoneRange: 2" to 7"
KD-3163Disc Brake Piston Toolfor most Domestic andImport VehiclesDesigned to rotate the parkingbrake-activated piston backinto the caliper cylinder whenreplacing worn pads on vehicles equipped with 4-wheeldisc brakes.
KD-2428Compression Tester• Tester checks cylinder
compression from 0 to 300 PSI (0 to 21 kg/cm2).
• Adapters fit 14 and 18mmspark plug holes
KD-3151Universal Internal & ExternalRetaining Ring Pliers• For up to 2.0" diameter rings• Includes five pairs of color-
coded precision-group tipsand Allen® wrench in conven-ient storage pouch.
assure gripping ability• Packaged in a vinyl pouch• Made in USAIncludes:• 9-3/4" Long Offset Jaw Pliers
(No. 824A) • 9-3/4" Long Straight Jaw Pliers
(No. 824S)• 7" Long Extra Strong
Non-Conductive Nylon Plier (No. 824N)
SET-824N7" Long Extra Strong Non-Conductive Nylon SparkPlug Boot Plier• Lightweight• Gripping teeth inside jaw
SET-865KITHose Clamp Pliers Kit• Includes a general 9" long plier
(No. 860G), and an extended jaw10-1/2" long plier for larger clamps (No. 860L)
• Services the mobea or constanttension band clamps 14mm - 44mm
• Jaws swivel through 360°• Finger-tip locking pawl makes it
possible to lock pliers in any one ofthree positions
• Includes extra tips, E-clips andsprings
• Made in the USA
SET-1201Door Panel/Window Wedge Tool• Removes automotive door panels
without damaging the door orpanel
• Also used as a window wedgewhen using a “lockout” tool
• Made in the USA
KD-3995Indexing Seal Puller• 5 positions per side,
11 total
SET-3714Rolling InspectionMirror• Great for BIG
inspections undertrucks, cars, etc.
• 7" x 14" rolling mirror
• Flashlight clip on thehandle (flashlight notincluded)
• Telescoping handlesexpands from 3-1/2feet to 6 feet
While Supplies
Last
PBT-70717Small Flexible Line ClampsTwin pack. 1/8" - 5/16".
PBT-70730Medium Flexible Line Clamps Twin pack. 1/2" - 3/4".
$49.95
$59.95
$10.95
$34.95
$9.95
$29.95
$99.95
$99.95
$35.95
$17.95
$29.95
$10.95
$48.95
$27.95
$139.95
$11.45 $18.95
99 1er janvier au 24 février 2012 • January 1 to February 24, 2012
AST-45055 Piece Fastener & MoldingRemover SetPlastic construction of tools prevents scratching and damage to work surface.
AST-160016 Piece Punch & Chisel SetProduct not covered under warranty.
AST-94022 Piece, Large 16" Ratcheting Snap Ring Plierswith Replaceable Tips
AST-213421 Piece 3/4" Drive Socket Set• 1 reversible ratchet• 1 flexible bar: 20"• 2 extension bars: 4" and 8"• 16 sockets: 7/8" to 2"
AST-2181A8 Piece 1/4" Shank DoubleCut Carbide Rotary Burr Setwith FREE 1/4" Shank Medium Die Grinder1/4" Medium Die Grinder:• 6-3/4" long• 1/3 HP motor• 22,000 rpm
AST-9409AFor Cars• For hose clamps with
diameters of 11/16" to 2-1/2"
AST-9423For Trucks• For hose clamps with
diameters of 11/16" to 3"
Hose Clamp PliersLifetime warranty on pliersbody only. Cable excluded.
AST-95894 Piece Upholstery Tool Set• 9-1/4" Bent handle door
panel remover• 9-1/2" Plastic fastener
remover• 10" Door upholstery remover• 20-3/4" Long door
panel remover
AST-74011/2" Drive Dual SidedImpact Socket toRemove Damaged Lug Nuts and Chrome Caps• 18.5mm and 19.5mm sides
AST-944725 Piece Screw Extractor,Drill & Guide Set• Extracts screws and bolts• Can be used on thread sizes
5mm to 16mm
Flexible 6 Point Socket SetsAST-74077 Piece SAE3/16" – 9/16"
AST-741212 Piece Metric5mm – 15mm
AST-8077SEDeluxe Auto-Darkening Solar Welding Helmet• Viewing area: 96mm x 62mm• Variable shade adjustment
9-13 DIN• Automatic power On / Off• Battery life up to 4000 hours
FREE! Welding Gloves with purchase of No. AST-8075SE.
FREE! Welding Gloves with purchase of No. AST-8077SE.
AST-8075SEAuto-Darkening Solar Welding Helmet• Viewing area: 98 mm x 44 mm• Variable shade adjustment
9-13 DIN• Automatic power On / Off
$15.95
$13.95
$54.95
$20.95
$129.95
$119.95
$31.95
$31.95
$45.95
$37.95 $44.95
$48.95
$77.95
$28.95
$114.95
$67.95
$30.95
$51.95
$169.95
$189.95
100 1er janvier au 24 février 2012 • January 1 to February 24, 2012
AST-78488 Piece Professional Brake Tool Set
AST-78928 Piece Fuel and Transmission Line Disconnect Tool Set
AST-7897Ball Joint Service Tool and Master Adapter SetWorks on upper and lower balljoints on most GM, Ford and Dodge2 and 4 wheel drive pickups.
AST-7822Harmonic Damper and Holding Puller SetHelps remove and install the crankbolt on most Chrysler, Hyundai,Mazda & GM engines.
AST-7865Ball Joint Service Tool with 4-Wheel Drive AdaptersFor removal and installation ofpress-fit parts such as ball joints,universal joint and truck brakeanchor pins.
AST-7802Tie Rod/Pitman Arm Adjusting Tool Set
AST-786011 Piece Disc Brake Pad andCaliper Service Tool Kit forDomestic & Import
AST-789510 Piece Fan Clutch Wrench Set• A must for any front engine
service• Works on wide range of Ford, GM
and Chrysler vehicles
AST-7893015 Piece Master Disconnect Kit• Fuel and transmission line
disconnect set• Oil cooler line remover• A/C and fuel line disconnect
AST-787303 Piece 1/2" Drive Extra LongChrome Wheel Lug NutImpact Socket Set with Protective Plastic Sleeves• Includes: 17, 19, 21mm with
3 extra plastic sleeves• Limited warranty
AST-7898Deluxe Noid Lite and GM IAC Signal Test Lights Set • Quickly and easily tests electronic
fuel injection signals• Eliminates the GM idle air control
(IAC) as possible fault on no-startvehicles
• Works on GM TBI, Bosch PFI, Ford TBI, GM PFI, Geo TBI and GM SCPI
AST-78200Mercedes-Benz & BMW Fan Clutch Service SetFor the removal of lock nuts on thermo-viscous fans found on Mercedes-Benz, BMW, Ford andmany other vehicles.
FREE! AST-7848 withpurchase of AST-7860.
AST-78585Radiator Pressure Tester and Vacuum Type CoolingSystem Kit• Allows easy testing for leakage in
radiator and quick change ofcoolant
• Unit suitable for domestic andimport vehicles
• Special design of vacuum purgeand refill tool connection fits near-ly all types of radiator openings
preventing damage to knuckle• This tool is adjustable and suitable
for steering knucles with either acentralized or non-centralized slot
• Suitable for clamping bores onAudi, BMW, Citroen, Ford, Peu-geot, Renault, Seat, Skoda, VWand many Japanese vehicles
AST-78241Wheel Bearing ReplacementAdapter Set• Change front wheel bearings
without having to remove thesteering knuckle or strut assembly
• Eliminates the need for front endalignment after service work iscompleted
• For use with domestic and importfront wheel drive cars and lighttrucks
$42.95
$37.95
$189.95
$54.95
$104.95
$92.95
$46.95
$62.95
$139.95
$24.95
$49.95
$67.95
$57.95
$77.95
$199.95
$359.95
$179.95
101 1er janvier au 24 février 2012 • January 1 to February 24, 2012
500 Lbs Capacity PortableWork Stands• Steel tubing construction
with 1/2" foam padded top• Height adjustable from 33" to 40"
AST-557003• Lightweight duty• 27.89mm tube
cross section
AST-557010• Extra heavy duty • 31.74mm tube
cross section
AST-7300MD200 Lbs Capacity Universal Rotating Parts Work Stand• Handles any panel or bumper to
make repairs and refinishing easy• Comes with 8 adjustable bars to fit
almost any panel securely• Allows for single handed rotation of
panels 350 degrees in 16 degreeincrements
AST-4550MDAir Operated Paint Shaker• Will shake paints through
1 gallon round cans• Shakes up to 750
cycles/minute
FREE! #AST-1426, 1/4" Heavy DutyHand Riveter with every purchaseof #AST-4550MD.
FREE! #AST-9004 (4 canvaswheel covers) with purchase of #AST-7300MD.
AST-55600500 Lbs Capacity 2 In 1 Convertible Work Bench Table/Scaffold• 2 height adjustments: 21.25" and 32.25"WORKBENCH MODE: (Surface: 39.6" x 18.8")• The tool tray is designed to hold hand tools, fasteners and standard paint
cans• Medium-density MDF fiberboard robust work surface for hammering, drilling,
and woodworking needs• The ruler and protractor graphics on the MDF surface allows for accurate
measurementsSCAFFOLD MODE: • Use as a sturdy standing surface for a multitude of tasksSTORAGE: Reduces to 4" thickness for easy storage
AST-3018MD23.5" Digital Tire Inflator• 21" hose• Works with TPMS• Works on a nitrogen system• Measuring range: 3 - 218 psi• Lithium battery lifetime: 140 hours• 1 button operation, auto shut-off• Two position lever (Deflate/Inflate)
FREE! AST-7445 – TireRepair Tool Kit – with purchase of AST-3018MD2.
AST-30813-1/8" Dial Tire Inflator• 21" hose• Inflate, deflate and measure tire pressure• Two position inflate/deflate level• Measuring range: 0 - 174 psi• Units: PSI/BAR
cleaning fluid tank• Cleans painting equipment inside & out in
less than 1 minute• Has a 1 gun & 1 cup capacity • Used cleaning fluid easily disposed via
drain valve• Auto stop timer and safety valve• Auto shut-off lid switch• CE Approved• 1 year warranty
AST-3070Portable Digital Tire Inflation Cartfor Use with Nitrogen or Air• Adjustable over pressure settings• Automatic purging programs• Safe, accurate and easy to use• Li-Ion battery operation• Inflate up to 4 tires simultaneously• Unit uses standard Nitrogen bottle or direct
Nitrogen air supply from generator, or usesstandard shop air compressor
• Inflation range: 0.5 - 10 Bar (145 psi)• Accuracy: ± 0.02 Bar (± 0.3 psi)
Reusable Coverall• Washable and reusable• Lightweight protective suit is easy to clean
and lint free• Full zipper front, velcro sleeve fasteners, full
hood, elastic waist and rear pocket• Comes in white nylon front, sleeves and hood
and blue breathable cotton backside
AST-4561Large
AST-4562X-Large
Pressurized Spray Gun Assemblies• Equipped with pressure gauge and fluid pressure regulator• Excellent for spraying large areas
AST-2PG7S2 L Pot• 1.2mm nozzle• 6 ft. hose
AST-PT2-4GH2-1/4 Gallon Tank• 1.0mm nozzle• 12 ft. hose
AST-2PG8S2 L Pot• 1.7mm nozzle• 6 ft. hose
$41.95 $54.95
$259.95
$257.95
$104.95
$64.95
$1295.00
$839.95
$199.95
$39.95
$204.95 $329.95$189.95
$39.95
102 1er janvier au 24 février 2012 • January 1 to February 24, 2012
AST-12221/4" 90° Angle Die Grinder & 1/4" Medium Die Grinder Kit• 20,000 rpm• Built-in regulator• Angle die grinder (No. 1240)• Medium die grinder (No. 1206A)
AST-400ESmart Eraser®
Pad for Pinstripeand DecalRemoval
AST-400EARArbor for SmartEraser® Pad
AST-3059Wheel Polishing Kit with Air Buffer• Restores aluminum & magne sium
rims, headlamps, engine parts,motorcycle parts and plastics
104 1er janvier au 24 février 2012 • January 1 to February 24, 2012
KAS-52215 Piece Fine Tooth Bit Wrench Set• 15° offset wrench, #1 & #2 Phillips,
1/4" and 9/32" slotted bits
KAS-97240 Piece MasterSAE & MetricRethreading Set
KAS-1129Retractable Test Leads10 foot x 3 alligator clips
KAS-1130Retractable Test Leads30 foot x 1 alligator clip.
KAS-1202512" Long x1/2", 25-BladeFeeler GaugeThickness range: .0015 to .040.
KAS-75Quick Switch Replaceable Tip Internal and External Retaining Ring Pliers• Automatic ratchet lock feature keeps rings open or closed for easy installation and removal• Internal: 1-13/16" to 4" and 46mm to 102mm• External: 1-1/2" to 4" and 36mm to 102mm
KAS-87Tool Kit with Tip Kit & Hex WrenchINTERNAL AND EXTERNAL: 31⁄2" – 7" (90 – 175mm)Bent 20° and 90° SAE: .120", .150", .180"Bent 20° and 90° Metric: 3.0mm,3.8mm, 4.6mm
KAS-5333Fine Tooth Serpentine Belt Wrench SetService automotive serpentine beltsequipped with spring-loaded tensioners, without having to remove other components.Includes: 6-point–13mm (1/2"), 14mm (9/16"), 15mm, 16mm (5/8"), 18mm, 19mm (3/4") and square drive– 3/8", 1/2".
KAS-95011 Piece Gasket Hole Punch SetFrom 1/4" to 1".
KAS-1138Magnetic Back Retractable Test Leads• 2 x 30-ft. magnetic test leads• Contains insulated alligator clips
KAS-11767-Pc Non-Magnetic Retract. Test Leads• 2 x 15-ft. test leads & one pair of each:
probes, alligator clips & spring hooks
KAS-B10A5/16'' GM Side Terminal Battery Wrench
KAS-65715/16" x 10mm Extra Long Battery Terminal Wrench
KAS-65255/16" Extra Long Ratcheting Side Terminal Battery Wrench
KAS-14653 Piece Quick Switch Retaining Ring Pliers Set• Contains one each of the Hi-Tech 1421, 1434 and 75 models• Internal: 1/4" to 4" and 8mm to 102mm• External: 1/8" to 4" and 3mm to 102mm
KAS-5541Revsersible Ratcheting Bit Wrench forGM Multifunction Switch• Used to remove/install the mutlifunction
switch on GM vehicles without removingother steering wheel column components
• Magnetic tool consists of a low profile 1/4"bit wrench with a T25 Ball Torx bit
KAS-85699/16" Extra Long Automatic Slack Adjuster Wrench• For brake service and slack adjuster
installation on heavy duty trucks equippedwith Bendix® automatic slack adjusters
• Used to turn the manual adjuster hex
1176
1138
1129
1130
$40.95
$10.95
$129.95
$62.95
$21.95
$99.95
$31.95
$25.95
$28.95
$109.95
$109.95
$46.95
$67.95
$34.95
$48.95
$17.95
$15.45
$18.95
$16.95
$46.95
105 1er janvier au 24 février 2012 • January 1 to February 24, 2012
SLY-91400BUniversal Valve Spring Compressor• For use on most foreign and
domestic engines• Removes and installs the valve
spring with the cylinder head stillon the engine and in the car, orwith the cylinder head removed.
SLY-91410BUniversal OHC Valve Spring Compressor Update Kit• Updates No. 91400A or
similar kits that have a 5/8" bar
SLY-88750ACompact OxygenSensor WrenchFor use with any size electrical connectors.
SLY-86400VW & Audi TensionPulley Spanner Wrench
SLY-99800AGM & Chrysler Water Pump/Fan Clutch Pulley Holder
SLY-87300VW & Audi StrutShock NutSocketFor late-model front wheel drivevehicles to remove the top strut retaining nut.
SLY-67600VW & Audi Timing Belt Pulley HolderWorks on:• 1.8L 4 cylinder turbo
SLY-6775012 & 6 Point Oxygen Sensor Wrench with Pivoting HandleFor use with most all oxygen sen-sors no matter what size electricalconnectors they have.
SLY-68600AHonda/Acura Ball JointRemover/Installer Tool• Removes and installs lower ball
joints on the car versus removingsteering knuckle and using a shoppress
• Used with an air hammer• Works on Honda/Acura and many
other makes of automobiles
SLY-68200BMW T60 Torx Serpentine Belt Tensioner ToolWorks on BMW 135, 335, 535 andall other models using the N54 twinturbo straight 6 cylinder engine.
SLY-66750BShielded Oxygenand Fuel SensorSocket, 6 Point• Designed to work
on all oxygen andair fuel sensors thatare shielded including:Toyota, Lexus, Honda, Acura,Maz da, Hyundai, Kia, Nissan,Infiniti
SLY-67650VW & Audi Timing Belt Tensioner Release Tool
SLY-68100Honda & Acura Front LowerControl Arm Bushing Remove& Reinstall Tool• Removes 65mm and 74mm
bushings found on many Hondaand Acura vehicles
• This tool cuts one hour off the job• The use of a press is not required
SLY-69800Volvo Fuel Pump Socket• This socket has been designed to
remove the left and right fuel pumpretaining nuts on all late modelVolvos.
• Fits on: S80 1999 and later; All 2001 and later
SLY-69250GM Duramax Flywheel Lock• Designed to hold the flywheel
stationary when removing orreplacing the crankshaft
• Works on 2001 and later 6.6 literDuramax diesel trucks
SLY-10200Toyota Serpentine Belt Tensioner WrenchApplicatons:• Camry: 2002 to present• Solara: 2004 to 2008• Matrix: 2009 to present• Highlander: 2001 to present• Rav 4: 2004 to present
SLY-96800Universal Camshaft PulleyHolding Tool• For most Asian overhead cam
engines• Especially useful on transverse
mounted V6 engines such as theVG30 used in Nissan Maximas,the 3VZFE and lMZFE enginesused in Toyota Camrys
SLY-10900Ford Diesel Fan Clutch PulleyHolding Tool• Works on 2011 - newer 6.7 L Ford
Diesel Power Sroke
SLY-10800Fan Clutch Pulley HoldingTool for Dodge, Chrysler, Jeep• Works on 2009 and later 5.6 L
Hemi Truck engine
SLY-10950Honda/Acura Serpentine BeltTensioner Wrench• 6 point 19mm end fits 2006 and
later Civics and many other Hondacars and trucks
• 12 point 14mm end gives accessto the adjuster on the 2003 andlater Honda Element or the HondaFit
$185.95
$75.95
$75.95
$93.95
$48.95
$36.95
$35.95
$39.95
$23.95
$87.95
$92.95$21.95
$63.95
$79.95
$62.95
$28.95
$54.95
$93.95
$77.95
$199.95
$134.95
$84.95
1er janvier au 24 février 2012 • January 1 to February 24, 2012106
Super Mutt® Deluxe Testerfor Air Brake Systems andTrailer Lights• Manual, remote control or
automatic testing• 12/24 Volt DC• Fits group 31 battery• 7-way round pin connectionELECTRICALSYSTEM TESTING • Power lights individually or all
at once• Locate and identify: short, crossed, open and
overloaded circuits• Pulses power to shorted and overloaded circuits• Access ABS fault codes• Amperage readout (0-20 Amps)• Audible and visible alertsAIR BRAKE TESTING • Pulse air to check brake operation with remote• Perform leak down test on service and
emergency lines• Adjust slackers and measure pushrods with
remote
IPA-8037Stainless Steel
IPA-8038Brass
IPA-9008SESuper Mutt® Deluxe SE PackageIncludes: (1) Remote control, 5 ft. 7-waycable, chassis ground cable, 6 ft. glad hands
IPA-9008DLSuper Mutt® Deluxe DL PackageIncludes: (3) Remote controls, 5 ft. 7-way cable, chassis ground cable, 6 ft. glad hands, batterycharger, face shield, rain cover
IPA-80247 Round Pin Terminal Cleaners for Trucks• Removes corrosion and resizes
female and male connections
IPA-8029Tractor Trailer Maintenance Kit• Includes #8024 Connector
Cleaners• Tests 7 round pin electrical circuits• Includes Deoxit® electrical
connections cleaner and enhancer
The Air Comb™ Filter Cleaner• Patent pending design• Cleans tube and cylindrical type air filters,
radiators & A/C condensers from the inside out• Focused high-pressure multi-port output• Long reach 90° air flow to access the
fies sound during diagnosis orverification of proper vehicle oper-ation
• Vibration Detector - Pinpointsfaulty bearings, injectors,squeaks, rattles, etc.
• Noise cancellation feature eliminates all background noise
STE-9628524" Long
STE-1015016" Long
STE-978448 Piece Manual Brake Gauge• Shows customer an accurate
measure of brake lining
STE-97202 ChassisEAR™ –Wireless Electronic Squeakand Rattle Finder• Instant cross-comparison between
all four channels can be made inone short test drive
• Pinpoints source and location ofnoise
STE-65001EngineEAR™ –Electronic StethoscopeQuickly pinpoints noise and locationof bad bearings, bushings dirty fuel injectors, wind and air leaks, noisyvalves and lifters.
Flexible Bend-A-Lights®• Use cover as extension• Bends and holds position• Batteries included
FLX-FB5000CV Boot Installer• Installs CV boots in less than 20 minutes• The CV boot installer is utilized by placing a universal CV Flexx Boot
over the installer’s retractable aluminum arms. Then, using compressed air, the boot is spread open wide enough to be passedover the axle shaft, without having to remove the axle.
• Includes a storage case
FLX-FB2000 For ATVs, very small cars and four wheelers
FLX-FB3001 For almost 100% of utility, 4x4 and car applications
FLX-FB3000 For 98% of automotive applications
FLX-FB4000 Rack and Pinion Boot for 100% of automotive applications
FLX-FB5025-34 50 PIECE SET. Includes 25 large and 25 small clamps.
STE-95929 12 Piece Universal European terminal tool kit
STE-95978 19 Piece VW/Audi master terminal tool kit with specialtools for coolant sensor, wiring harnesses and terminal blockson Chrysler, Hyundai, KIA, Mitsubishi and other newer vehicles
$179.95
$135.95
$38.95
$849.95
$29.95
$194.95$74.95$96.95
$129.95$149.95
$95.95
$22.95
$339.95
$125.95
$334.95
$18.95$24.95$18.95$23.95
$49.95$22.95$29.95
95839 95927
9592695928
95929
95978
109 1er janvier au 24 février 2012 • January 1 to February 24, 2012
STR-CLT2PBCylinder Leakage TesterMeasures the ability of an engine cylinder to hold compressed air pressure and supplements a compression tester.• Larger, easier to read leakage
and pressure gauges• New indsutrial interchange quick
couplerIncludes:• New M14 short thread adapter on a 26" hose assembly• M14 long thread solid adapter
STR-TU1PBDeluxe Vacuum and Fuel Pump TesterFor all domestic and imported cars &trucks with gasoline engines. Large3-1⁄2" four colour easy to read gaugewith hook for versatility. Range ondials is 0 to 28"/0 to 70cm vacuumand 0 to 10 PSI/0 to 0.7 kg/cm2.
STR-TU470BFuel Injection Canister Cleaner• Two larger, easier-to-read gauges
enable technician to check fuelpressure and set cleaningpressure at the same time
• Cleans carbon from intake valves, fuel passages and cylinders
• 20 oz. capacity bottle sits flat for filling
STR-TU1553Super American DieselCompression Test Set• All GM, Isuzu, Lincoln Mark
VII Continental and FordNavistar;
• Audi, Mercedes, Peugeot, Toyota, VW, Volvo;
• No. 15-17 for Cummins usedon Dodge SUVs and trucks
• No. 15-22A for 7.3L Turbo Direct Injection for Navistar/Ford
STR-TU1570Heavy Duty Global Diesel Compression Test SetContains tester and all the most popular adapters needed to test heavy duty trucks and equipment.
STR-TU443-3Fuel Injection Update KitUpdates TU-443U Kit to TU-550,enabling fuel injection tests on all major domestic and foreign platforms1988 to present.
STR-TU3PBUniversal Compression TesterTests compression on all domesticand imported cars and light trucksand gasoline engines. Includes 14 and 18mm short, 14 and 18mm long flex, and 14mm long reach adapter.
STR-TU30ASuper Compression TesterTests compression on all domestic and imported cars and light trucks, gasolineengines and mini engines. Includes:• 24" hose assembly with quick coupler• New M12 x M16 adapter for Ford Triton
engines• New 8" M14 short thread solid adapter
for deeply recessed spark plug holes• M14 adapter short and long• M10 adapter with short thread• Small engine tester (No. TU-21) with
M14 x M18 threads and PSI/Bar gauge
STR-TU24APBThree Way Exhaust Back Pressure KitAllows quicker and more accurate testing of exhaust blockages in catalytic converters, mufflers, etc. Can test in: Oxygen Sensor, Exhaust Pipes, Air Injection System.
STR-TU550Master Global Fuel Injection Test Kit• Covers virtually all major
domestic and foreign platforms 1988 to present
• The redesigned 71317 fuel line tee can accommodate 3/8", 1/4" and 5/16" hose sizes
• Kit contains: 16mm O-ring adapter and bolts(Hyundai & Mitsubishi), 11mm O-ring adapter and bolts (Nissan and Infiniti), and M12 x 1.00 Honda pulse damper adapter (Accord,Civic, and S2000)
STA-12270Universal Cooling System and Pressure Cap Tester• Tests pressure
up to 30 lbs• Includes blow molded case
PBT-70888Complete CoolingSystem & Cap Test Kit• Universal bladder for
100% coverage fordomestic and import vehicles
• Cap adapter kit has 8 sizes to adapt to allradiator caps
$128.95
$42.95
$269.95
$229.95
$559.95
$129.95
$59.95
$164.95
$109.95
$579.00
STARPRODUCTS
$114.95
$179.95
110 1er janvier au 24 février 2012 • January 1 to February 24, 2012
Radiator Adapters
ASM-FZ580Cooling System AdapterKit for Deep and Shallow Radiator NecksWorks with many different Asianand Domestic vehicles.
ASM-6500VW/Audi Axle Nut Socket Set• 14mm and 17mm Allens• 30 & 32mm-12 point sockets
ASM-T10050Crankshaft StopUsed to lock the crankshaft in placeduring timing belt replacement on2004-2005 VW Golf, Jetta and NewBeetle with T.D.I. Pumpe Duse.Used with 3359 lock pin andH2587-1 pin wrench.
ASM-SP1412BMW Spark Plug Socket• 3/8" drive socket, 14mm, 12 point• Applicable to 2007 and later BMW
335 and 535 with 3.0L twin-turbomotors
• Slender in design to fit application
Stud Puller Remover Kits
ASM-6800TDITiming Belt Tool Set for VW TDIUsed for locking the camshaft, crankshaft and diesel pump while setting the timing belt. Applicable to: 1999-2008 VW TDIand Pumpe Duse engines.
ASM-EU2000BrakeCaliper/Bleeder Service SetWrenches fitbleeder screwson Mercedes,BMW, Volvo &VW/Audi models.
ASM-HON1419Honda Serpentine BeltWrenchEquipped with 14mm and 19mm,12 point secured sockets, forengagement every 30 degrees.Ideal for strong tensioners used on2006 and newer civics.
ASM-FZ29 Works with many asian vehicles as well as some domestic
ASM-FZ32A Works with many domestic vehicles and some Mercedes and Nissan models
ASM-FZ35A Works with many different domestic vehicles
ASM-FZ36 Works with many different domestic vehicles
ASM-FZ41 Fits the New 2009 Audi A4, Q5 and Q7. 1996 and newer Audi and 1998 and newer Volkswagen models. Porsche Cayenne.
ASM-FZ47 Fits the 2012 Ford Focus. 2004-2010 Volvo S40 & V50 (new body style), and all Volvo 2008-2010 (except XC 90). 2007-2008 Land Rover LR2.
ASM-FZ128 Works with many different Asian/Domestic vehicles
ASM-FZ138 Works with many different Asian/Domestic vehicles
ASM-BMW345 Works with 1988-2008 BMW, except the new 3 (E90), 5 (E60), and 6 (E63 and E64) series. Land Rover Range Rover 1995-2004, Discovery 2002.
ASM-BMW350 Works with 2006-2009 BMW 3 Series (E90), 2004-2009 5 and 6 Series (E60, E63, E64) and X5 2007-2009 (E70)
ASM-M0349 Works with Mercedes models with a threaded filler neck (except M-Class, 163 body) and ML 350 (new 164 body) 2006.
ASM-2016mm – 12mm
ASM-2021/4" – 1/2"
ASM-2031/4" – 5/8"
ASM-T40069Crankshaft Locking Pin for VW/AudiFits 2005 and newer VW/Audi models with 3.2L FSI engines (BKH& CALA), and 2.5L 5-cylinderengines.
ASM-T40070Pair of Cam Lock Clamps for VW/Audi• Fits 2005 and newer Audi models
• Fits 2005 and newer VW modelswith 2.5L 5-cylinder engines
ASM-BMW6208BMW Timing Tool Set• Fits 2002 and newer BMW
models with N62 V8• Used to set timing on cams of
both cylinder heads• Includes hold down tool for cam
fixtures• Includes crankshaft timing pin
ASM-BMW0062BMW A/C Compressor Drive Belt Installing Tool• Applicable to BMW N62 (V8)
motors in 2004 through 2006models with the stretch belt
ASM-8110 10 Piece Disconnect Tool Set for Fuel and Oil LinesApplies to Nissan,Toyota, Tahoe, Suburban, Ford, GM.1/4", 5/16", 3/8", 1/2" sizes.
ASM-8021 3/8" Oil Cooler Line RemoverFor Ford trucks & SUVs. Fits 2007-2008 Ford F150.
ASM-8023 1/2" Oil Cooler Line RemoverFor 2005-2008 Ford F Series Turbo-Diesel trucks,2009 Escape with 6F transmission, Ford Edge.
ASM-8024 1/2" Oil Cooler Line RemoverFor 2007 Ford Explorer and Sport Trac
ASM-BMW8390 BMW Fuel Line Disconnect Tool2006-2011 3 Series, 2006-2009 X3 models (E90 & E83)
$13.95$33.95$47.95$35.95
$52.95
$52.95$49.95$49.95
$48.95
$48.95
$52.95
$119.95
$19.95
$23.95
$25.95
$34.95
$86.95
$99.95
$56.95
$73.95
$103.95
203
$49.95
$35.95
$36.95
$309.95
$43.95
$46.95
$309.95
$59.95
$229.95
$149.95
8110
8021
8023
8024
BMW8390
1er janvier au 24 février 2012 • January 1 to February 24, 2012111
http://youtu.be/WtHErEsYMps
ASM-21017 Piece Oil Filter Tool Set• For many domestic and foreign
applications• Sizes: 27, 32 36, 74, 74.5 84 and
86.5mm
ASM-TOY300Toyota Oil Filter Wrenches• Set includes TOY640, TOY730 &
MO219 oil filter wrenches. Coversevery Toyota gas engine modelsbetween 1983 and 2006.
• Also covers new style oil filterhousing cap on 2005 Avalon &2006 Lexus GS300.
ASM-T40057Oil Filter Housing Drain• For 2005-2006 VW and Audi
models with the new 2.0 T motorand the 2.5 in-line 5-cylinder VWengine
• Prevents spillage and allows for100% drainage of oil from thehousing
ASM-V410Volvo Oil FilterWrench1999 to 2001 Volvo cars.
ASM-ATF1002BASIC3 Liter Basic Drive Line Filler SystemUsed for filling fluids in transmission, differentials and transfer cases (not suitablefor use with fuels or solvents).• Includes ATF102 adapter applicable to
BMW, Honda, Nissan and many other universal applications. Ideal for Honda SUVdifferential fill.
Filling Adapters for No. ATF1002BASICASM-ATF101 Ford 1/8" NPTASM-ATF103 VW Short AdapterASM-ATF104 VW Long AdapterASM-ATF108V Volvo 5/16 x 24ASM-ATFTOY118 Toyota 18 x 1.5ASM-ATF17CVT Audi CVT Transmission 24 x 1.5ASM-ATF16DSG VW/Audi DSG Transmission 24 x 1.5ASM-ATF10H VW/Audi Haldex DifferentialASM-ATF129 Mercedes 722.9 Transmission 12 x 1.5
ASM-F25005 Piece Oil Filter Socket Setfor 1988-2010 Ford ModelsIncludes 24, 36, 76, 93 and 74mmoil filter sockets and wrenches.
Torque Wrenches• “Split beam” torque measuring mechanism that requires only
fingertip force to adjust• Adjust from the bottom to the top of the scale in seconds• No need to reset the tool to the bottom of the scale after use• Blow molded case included• 1 year manufacturer warranty
Model Drive Ft-Lb Increments Length Price
PRC-C2FR100F 3/8" 20 - 100 2 ft-lb 17-5/8"
PRC-C3FR250F 1/2" 40 - 250 5 ft-lb 22-1/8"
PRC-C4D600F* 3/4" 200 - 600 10 ft-lb 48"
PRC-C5D600F* 1" 200 - 600 10 ft-lb 48"
Model Sq. Drive Torque Range Price
ACD-ARM602-3 3/8" 3-60 ft-lb (4-80 Nm)
ACD-ARM602-4 1/2" 4-150 ft-lb (5-200 Nm)
Model Drive Input Input Ft-Lb Drive Output Output Ft-Lb Price
CEN-6380 1/2" 250 ft-lb 3/4" 1000 ft-lb
CEN-6387 3/4" 500 ft-lb 1" 2000 ft-lb
* These models come with a fixed head, not a flexible head.
4:1 Ratio Torque Multipliers
Part No. Drive Torque Graduations Length Price
ATD-100M 3/8" 25-250 in-lb 1 in-lb 13.4"
ATD-103 3/8" 10-100 ft-lb 0.5 ft-lb 17.5"
ATD-101M 1/2" 20-150 ft-lb 1 ft-lb 20.8"
ATD-102M 1/2" 25-250 ft-lb 1 ft-lb 23.1"
ATD-109 3/4" 100-600 ft-lb 5 ft-lb 43"
ATD Metric/SAE Micrometer Torque Wrenches• Positive lock torque setting right or left• Complies with ANSI/ASME and ISO• Storage case not included for ATD-103. Please order ATD-123.
Digital Torque Adapters• Turn a regular ratchet into a Digital Ratchet• Static torque measurement• Standard functions:
torque setting, measurement setting, mode setting• Operation in both clockwise and counter-clockwise directions• LCD display shows ft-lb, in-lb, Nm, kg-cm measurements• Audible torque confirmation buzzer• Easy to set up Set, Peak or Track modes• Accuracy: Clockwise ± 2%; Counter-clockwise ± 3%• Battery: (2) coin cell CR2032
CIT-C23030 Gallon Parts Washer• Capacity of 17-28 gallon solvent• Tank: 27'' W x 35'' L x 9'' D• 110V pump• CSA approved
FIL-FR112Rotary Hand Pump with 8' Hose• Effective with medium viscosity liquids,
as well as oils, gasoline and diesel fuels• Transfer at up to 10 GPM
(38 LPM) per 100 revolutions• Built-in check valve and strainer• UL Listed
FIL-FR152Piston Hand Pump with 8' Hose• This compact, high flow, dual action design delivers
up to 20 GPM (76 LPM) per 100 strokes • Pump flow can be reversed by rotating piston 180° • UL Listed
Basic Flow Meter• Mechanical flow meters designed for metering diesel
fuel, gasoline, kerosene, mineral spirits, Stoddard solvent and heptane
• Operates at 19-76 LPM (5-20 GPM), ±3% accuracy.
FIL-900DDigital Flow Meter – 1" Inlet/Outlet• Designed for metering diesel fuel, kerosene, mineral
spirits, standard solvent and heptane• Measures in: gallons, quarts, liters, pints, ounces,
user-definded units• Operates at 22-151 LPM (6-40 GPM), ±1% accuracy.
FIL-FR807CL3/4" Inlet/Outlet
FIL-FR807CL11" Inlet/Outlet
CIT-C2020 Gallon Parts Cleaner• Rugged welded steel • Removable work shelf • Parts basket for shaking small parts in solvent• Self-latching fuse linked fire cover• 110 Volts/60 cycle solvent pump • Recirculates 10-12 litre/ minute of solvent • Solvent capacity: 12 gallons • ULC/CSA approved
FIL-FR161212 Volt DC Diesel Fuel Portable Transfer Pump• 1/3 HP motor, 2800 rpm• Up to 10 GPM• 3/4" NPT inlet/outlet• For use with: diesel fuel & anti-freeze
FIL-FR20VLever Piston Hand Pump• 11 oz (325ml) per stroke • 3/4" outlet• 2" threaded tank adapter• 1" polymer suction pipe adjusts for 15 to 55 gallon drums• For use with: engine oils, gear oils, anti-freeze,
mild acids, degreasers & paraffin
FIL-SD62Standard Duty Rotary Hand Pump• 8 GPM (30 L) based on 100 revolutions• 3/4" inlet/outlet, 2" threaded tank adapter• For use with: gasoline, diesel fuel, light viscosity
