Date post: | 15-Mar-2016 |
Category: |
Documents |
Upload: | alexa-ratliff |
View: | 56 times |
Download: | 4 times |
Sandia is a multi-program laboratory operated by Sandia Corporation, a Lockheed Martin Company,for the United States Department of Energy’s National Nuclear Security Administration
under contract DE-AC04-94AL85000.1
Laboratory Chemical Hoods:How they work & when they don’t.
3
Laboratory Chemical Hood Also called a fume hood or fume cupboard Designed to limit exposure to hazardous or
unpleasant aerosols First used by alchemists 500 years ago
6
LEV Implementation Identify/Characterize Contaminant Characterize Air Movement Identify Alternative Controls Choose Most Effective Control Implement Control Evaluate Control Maintain Control
7
LEV Capture Ability Hood configuration (type of hood)
Extent of enclosure (e.g., glove boxes completely
enclose)
Air movement in hood (smooth, laminar, non-turbulent)
8
Duct Design Provide adequate capture velocity
– Usually 80-120 fpm (0.4 - 0.6 m/s)
Maintain duct transport velocity– For chemical laboratories ~ 2500
cfm (1.2 m3/s)
9
Duct Design, cont’d. Keep system balanced,
- i.e., equalize supply and return air - match airflows among manifolded
hoods Minimize power consumption
- i.e., conserve energy - save money
http://www.clf.rl.ac.uk/facilities/AstraWeb/images/Photo7/Air_duct_TA3.JPG
10
LEV Hood Design Requirements
Capture emissions close to source. Move contamination away from breathing zone. Consider existing air movement when locating
hood. Minimize air movement in source area. Should not interfere with work.
11
Laboratory hoods and ventilation are the basis of engineering controls.
But they must be properly: selected, located, used, and maintained.
Laboratory Hoods
12
Hood Location Requirements
As near to contamination source as possible So contamination moves away from operator Minimize cross-drafts Don’t place near windows and doors Don’t place near air conditioning/heater diffuser Doesn’t interfere with other workers Locate out of traffic flow Place near rear of laboratory
14
A person walking at 2-3 mph (0.9-1.3 m/s) generates cross drafts of 250 fpm (1.3 m/s) that can interfere with hood capture
15
Principles of Hood Design and Operation
Enclose as much of the operation as possible Place utility controls (gas, electric) outside or as near
hood front as possible Hood lights should be vapor tight Mount hood motor outside building and away from
building air intakes Don’t use hoods for uses not intended (e.g., perchloric
acid digestion, radioisotopes) Ensure duct material compatible with exhausts Don’t use without indication it is working properly
16
Hood Design & Operation, cont’d.
Don’t put your head in the hood. Use proper PPE (gloves, eyewear, etc) Place large equipment above surface
on 5 cm blocks to allow uniform air flow
Lower sash height to 30 - 50 cm during operation
Keep sash fully closed when not in use Use liner or tray inside hood to contain
spills http://www.news.harvard.edu/gazette/daily/0403/photos/03-meltonstem_1.jpg
17
Hood Design & Operation, cont’d.
Work in the center of hood and 15 cm in from hood sash.
Don’t store chemicals or equipment in hood. Don’t block baffles (slots). Maintain hood regularly (check fan belt,
lubricate motor). Regularly evaluate hood (flow rate, mark
operating sash height). Reports problems, concerns, malfunctions
immediately.
18
Laboratory Hood Types
Constant Air Volume (CAV)- Traditional/Standard/Conventional- Bypass - HOPEC (horizontal/vertical sash)- Auxiliary Air (not recommended for Lab
operations)
Variable Air Volume (VAV)
19
All make up air enters through hood face. Air exhausted is constant regardless of size of face
opening or sash height. Volume of air movement is constant but velocity
varies with sash height.
Traditional Constant Volume Hood
20
- Make up air enters through face and through a bypass.
- Bypass opening varies in size as sash is opened or closed.
- As sash moves, an almost equivalent area is uncovered to maintain a constant open area, hence, a constant volume of air movement through the face is achieved.
Constant Volume Bypass Hood
21
- Designed to reduce energy consumption.
- Discharges unconditioned make-up/auxiliary air from outside directly above and over user in front of hood.
- Uncomfortable to use and can produce turbulence at hood face.
Auxiliary Air Hood(not recommended for Lab operations*)
* According to ANSI Z9.5
22
HOPEC Hood (Hand Operated Positive Energy Control)
Combination Horizontal/vertical sash limits sash opening to no more that 50%.
Maintains constant air volume and limits energy consumption.
23
Uses mechanical and electronic controls to maintain constant air velocity.
Interfaces with room supply air to conserve energy by maintaining constant face velocity.
Uses complicated electronic components that require special training to maintain.
Variable Air Volume (VAV) Hood
24
Specialized Hoods
Perchloric acid (with water wash down) Radiological (with special filters) Floor level (improperly called walk-in) Distillation/California hoods (~1.5 ft or 0.5m above floor) Canopy hoods (not suitable for most lab operations) Slot hoods Ductless fume hoods Vented enclosures or special purpose hoods Glove Boxes (complete enclosure) Biological Safety Cabinets (BSC)
32
Ductless Hoods
Should only be used in laboratories with:• Small quantities of known non-volatile
substances.• Only with HEPA filters• Never with volatile substances • Unless breakthrough time for the specific
chemical being used is known, carbon filters are unreliable.
34
Several types/classes and configurations.
Designed to protect the sample, and sometimes the worker, from biological contamination.
Most types not suitable for hazardous, volatile chemicals.
Often not vented to the outside.
Reference: http://www.cdc.gov/od/ohs/biosfty/bsc/bsc.htm
Biological Safety Cabinets (BSC)
35
Hood Problems and Pitfalls
Face velocity- Recommended 80 - 100 fpm (0.4 - 0.5 m/s)
Air changes/hour- Recommended 6 – 10 / hour
Neither of these measurements can guarantee hood capture or containment.
36
Hood Evaluation Face Velocity, a necessary but not sufficient
condition. Smoke Tubes Smoke Candles Incense ASHRAE 110-1995 Test (SF6) Protection Factors (300-10,000):
PF = Contaminant Concentration in Exhaust Air
Contaminant Concentration in Breathing Zone
37
Ventilation System Evaluation
• Smoke sources- Visualize air movement- Assess capture effectiveness
• Smoke tubes• Smoke candles• Theatrical smoke generators• Incense sticks
38
Ventilation System Evaluation
• Velocity measurements- Anemometer/velometer
• fpm or m/s• Directional
- Hot-wire anemometer • fpm or m/s• Non-directional
39
Hood Smoke EvaluationFace velocity vs.
Containment Lab hood performance testing evaluates containment of
contamination. How do we determine containment? Is face velocity the right measurement? Studies show that 59% of the hoods passed face velocity
criteria, but only 13% of these hoods met ASHRAE 110 tracer-gas standards.
30% - 50% of hoods leaking excessive levels of contaminants pass face velocity tests.
Lab hoods with face velocities as low as 50 fpm (0.25 m/s) can provide protection factors 2,200 times greater than hoods with face velocities of 150 fpm (0.76 m/s).
40
ASHRAE 110 Containment Test
Measures containment using SF6 as a tracer gas SF6 is generated inside the hood at 4L/min. A mannequin with a detector in the breathing
zone (mouth) is placed outside the hood The detector is connected to a recorder The hood is also tested with smoke The hood is subjected to a walk-by test Effect of opening & closing sash is determined
Conclusions
Ensuring laboratory hood safety depends on many factors including:◦ Hood design◦ Hood use◦ Lab design◦ System operation
49