LAKEHEAD UNIVERSITY - ARCH SERVICES Lakehead Health... · mat'l material max maximum min minimum...

GROUP 'C' AND 'D'

ONTARIO BUILDING CODE DATA MATRIX - PART 11 - RENOVATION OF EXISTING BUILDING OBCREFERENCE

11.1 EXISTING BUILDINGCLASSIFICATION:

DESCRIBE EXISTING USE: 11.2.1

CONSTRUCTION INDEX: T 11.2.1.1A

HAZARD INDEX: T 11.2.1.1B

NOT APPLICABLE (NO CHANGE OF MAJOR OCCUPANCY) TO N

11.2ALTERATION TO EXISTINGBUILDING IS:

BASIC RENOVATION 11.3.3.1

EXTENSIVE RENOVATION 11.3.3.2

11.3 REDUCTION IN 11.4.2PERFORMANCE LEVEL: STRUCTURAL: 11.4.2.1NO YES

BY INCREASE IN OCCUPANT LOAD: 11.4.2.2NO YES

BY CHANGE OF MAJOR OCCUPANCY: 11.4.2.3NO YES

PLUMBING: 11.4.2.4NO YES

SEWAGE-SYSTEM: 11.4.2.5NO YES

11.4 COMPENSATING 11.4.3CONSTRUCTION: STRUCTURAL: 11.4.3.2NO YES (EXPLAIN)

INCREASE IN OCCUPANT LOAD: 11.4.3.3NO YES (EXPLAIN)

CHANGE IN MAJOR OCCUPANCY: 11.4.3.4NO YES (EXPLAIN)

PLUMBING: 11.4.3.5NO YES (EXPLAIN)

SEWAGE SYSTEM: 11.4.3.6NO YES (EXPLAIN)

11.5 COMPLIANCE NO 11.5.1ALTERNATIVES PROPOSED: YES (GIVE NUMBER(S))

11.6 ALTERNATIVE NO 11.5.2MEASURES PROPOSED: YES (GIVE NUMBER(S))

2

4

NO. DATE DESCRIPTION

1 01/14/2015 FOR PARTIAL REVIEW - LU

2 01/22/2015 FOR FINAL REVIEW - LU

3 01/23/2015 FOR TENDER

DATE

BROOK MCILROY INC. I 37 CUMBERLAND STREET,SUITE 202 THUNDER BAY, ON P7B 2T4

T. 807 683 8005 F. 416 504 7712

ARCHITECTURE I LANDSCAPE ARCHITECTURE I URBAN DESIGN I PLANNING

SHEET NO.

DRAWN

PROJECT NO.

SHEET TITLE

ALL DRAWINGS, SPECIFICATIONS AND RELATED DOCUMENTS ARE THE COPYRIGHT PROPERTY OF THEARCHITECT AND MUST BE RETURNED UPON REQUEST. REPRODUCTION OF DRAWINGS, SPECIFICATIONSAND RELATED DOCUMENTS IN PART OR IN WHOLE IS FORBIDDEN WITHOUT THE ARCHITECTS WRITTENPERMISSION. DO NOT SCALE FROM THIS DRAWING. THE CONTRACTOR SHALL VERIFY ALL DIMENSIONS ATTHE BUILDING SITE AND REPORT ANY DISCREPANCIES TO THE CONSULTANT PRIOR TO PROCEEDING WITHTHE WORK.

CLIENT

PROJECT NAME

LakeheadU N I V E R S I T Y

BrookMcIlroy/

1/22

/201

5 4:

39:3

8 PM

V:\2

012\

TB -

12-0

26-L

akeh

ead

Uni

vers

ity -

Arch

Ser

vice

s\12

-026

.13

- Hea

lth &

Cou

nsel

ling

Cen

tre (P

retti

e R

esid

ence

)\B -

Dw

gs +

Imag

es\B

2 D

raw

ings

\B2.

0 R

evit\

12-1

26.1

3 H

ealth

& C

ouns

ellin

g C

entre

(Pre

ttie

Res

iden

ce) -

Jan

14

2015

.rvt

Lakehead University955 Oliver Rd, Thunder Bay, ON

Cover Sheet

12-026.13

VLD

JANUARY 2015

A0

Prettie Health Unit Renovations(PR14-004)

LAKEHEAD UNIVERSITY - ARCH SERVICESPrettie Health Unit Renovations

955 Oliver Road, Thunder Bay, ON P7B 5E1

Lead Consultant:

BrookMcIlroy202-37 Cumberland St. S.

Thunder Bay, Ontario, P7B 2T4www.brookmcilroy.com

t. 807 683 8005 [email protected]

LIST OF DRAWINGS

ARCHITECTURAL DRAWINGS:

MECHANICAL DRAWINGS:

ELECTRICAL DRAWINGS:

A0 Cover SheetA1 Legends, Specifications, & SchedulesA2 Renovation PlanA3 Sections and DetailsA4 Sections and Details

Sub-Consultant:

Profor Engineering Services Ltd.5th F-200 Syndicate Ave S.

Thunder Bay, Ontario, P7E 1C9

M1 Partial Main Floor Plan Demolition and Renovation

M2 Mechanical Specifications, Equipment List, Scope of Work, Sequence of Operations, and Piping

E1 Partial Main Floor Plans Electrical Demolition andRenovation Electrical Legend, Single Line Diagram

E2 Electrical Specifications

ABBREVIATIONS

AFF ABOVE FINISHED FLOORALUM ALUMINUMBF BARRIER FREECL CENTERLINECMU CONCRETE MASONRYUNITCOL COLUMNCONC CONCRETEELEV ELEVATIONEP ELECTRICAL PANELEW EYE WASH STATIONEXIST EXISTINGEXP EXPOSEDFA FIRE ALARMFD FLOOR DRAINFIN FINISHFF FINISHED FACEGA GAUGEGALV GALVANIZEDGL GLASSGYP GYPSUM BOARDHM HOLLOW METALLG LAMINATED GLASSMAT'L MATERIALMAX MAXIMUM

MIN MINIMUMMTL METALN/A NOT APPLICABLENIC NOT IN CONTRACTNTS NOT TO SCALEOC ON CENTERO/H OVER HEADOWSJ OPEN WEB STEEL JOISTPLY PLYWOODPT PRESSURE TREATEDPTD PAINTEDR/W REINFORCED WITHSIM SIMILARSL SEALERSS STAINLESS STEELSTL STEELTEMP TEMPORARYTG TEMPERED GLASST/O TOP OFTYP TYPICALU/S UNDERSIDE OFW/R WASHROOMWD WOODWG WIRED GLASS

XX

AX

XXX

XX

XX

AX

XX

WX

BUILDING SECTION

STRUCTURAL GRID & BUBBLE

ROOM NAME & NUMBER TAG

ELEVATIONS

DOOR NUMBER

INTERIOR/EXTERIOR WALL TYPE TAG

WINDOW/LOUVER TYPE TAG

SYMBOL LEGEND

DETAIL NUMBER

SHEET NUMBER WHEREDETAIL REFERENCE FOUND

EXTERIOR BUILDING ELEVATION

INTERIOR BUILDING ELEVATION

AX XX

AX XX

DETAIL NUMBERSHEET NUMBER WHERE DRAWN

DETAIL NUMBERSHEET NUMBER WHERE DRAWN

Level NameElevation

XXX

Room Name

DETAILS

1 HOUR FIRE SEPARATION

GENERAL NOTES

1. ALL DIMENSIONS TO BE VERIFIED ON SITE

2. DOUBLE STUD AROUND OPENINGS IN EXCESS OF 400m2

3. CONTRACTOR TO COORDINATE ALL MECHANICAL ANDELECTRICAL WORK WITH ARCHITECTURAL.

4. COORDINATE ALL MECHANICAL AND ELECTRICAL SERVICESWITH POURING OF CAST-IN-PLACE CONCRETE.

5. ALL PARTITIONS TO EXTEND TO UNDERSIDE OF TRUSSESUNLESS OTHERWISE NOTED.

6. INTERIOR PARTITION TYPES INDICATE ORDER OFCONSTRUCTION FROM POINT OF ARROW THRU PARTITION.

7. LOCK SETS WILL BE GRADE 1 BY SCHLAGE. KEY WAY INFORMATIONTO BE PROVIDED BY LAKEHEAD UNIVERSITY'S BUILDING MAINTENANCEDEPARTMENT.




3 01/23/2015 FOR TENDER

KEYING NOTES

1. LOCK SETS WILL BE GRADE 1 BY SCHLAGE. KEY WAY INFORMATION TO BEPROVIDED BY LAKEHEAD UNIVERSITY'S BUILDING MAINTENANCE DEPARTMENT.

DATE


T. 807 683 8005 F. 416 504 7712


SHEET NO.

DRAWN

PROJECT NO.

SHEET TITLE


CLIENT

PROJECT NAME


BrookMcIlroy/

1/22

/201

5 4:

40:1

4 PM

V:\2

012\

TB -

12-0

26-L

akeh

ead

Uni

vers

ity -

Arch

Ser

vice

s\12

-026

.13

- Hea

lth &

Cou

nsel

ling

Cen

tre (P

retti

e R

esid

ence

)\B -

Dw

gs +

Imag

es\B

2 D

raw

ings

\B2.

0 R

evit\

12-1

26.1

3 H

ealth

& C

ouns

ellin

g C

entre

(Pre

ttie

Res

iden

ce) -

Jan

14

2015

.rvt


Legends, Specifications, &Schedules

12-026.13

VLD

JANUARY 2015

A1


Door And Frame Schedule - New Construction

DoorNo. Room Name

Door

Existing Door New DoorERExit

Hold OpenDevice Keyed Entrance

SupplyLockset

Core Repinnedby Lakehead

University CommentsType104 STAIR DOUBLE Yes No YES SPECIAL #1 AND #2 Yes No105 STAIR SINGLE Yes No YES SPECIAL #1 Yes No ALARM106 CORRIDOR SINGLE Yes No SPECIAL #1 Yes No ALARM111 WAITING AREA DOUBLE Yes No No No INSTALL SURFACE

MOUNTED PADBOLT 1068-6"115 CORRIDOR SINGLE Yes No YES GENERAL CENTRE Yes No115A CORRIDOR SINGLE No Yes YES SPECIAL #1 Yes No116 WAITING AREA DOUBLE Yes No YES SPECIAL #1 Yes No121 HEALTH PROMOTION RM. SINGLE Yes No GC - KEYED AREA 2 No Yes123 HEALTH PROMOTION OFF. SINGLE Yes No GC - KEYED AREA 2 No Yes129 ALLIED HEALTH PROF. SINGLE Yes No GC - KEYED AREA 4 No Yes130 COUNSELLOR OFFICE SINGLE Yes No GC - KEYED AREA 1 No Yes131 PSYCHIATRIST SINGLE Yes No GC - KEYED AREA 1 No Yes132 SR. COUNSELLOR OFFICE SINGLE Yes No GC - KEYED AREA 1 No Yes133 CLINIC MH ASSESSMENT SINGLE Yes No GC - KEYED AREA 1 No Yes137 DIRTY UTILITY SINGLE Yes No GC - KEYED AREA 1 No Yes138 COUNSELLOR OFFICE SINGLE Yes No GC - KEYED AREA 1 No Yes139 TRIAGE SINGLE Yes No GC - KEYED AREA 1 No Yes140 COUNSELLOR OFFICE SINGLE Yes No GC - KEYED AREA 1 No Yes141 OBSERVATION RM. SINGLE Yes No GC - KEYED AREA 1 No Yes142 GROUP ACTIVITY RM. SINGLE Yes No GC - KEYED AREA 3 No Yes142A GROUP ACTIVITY RM. SINGLE Yes No YES SPECIAL #1 Yes No CONNECTED TO EXISITING

EMERGENCY ALARM.142B GROUP ACTIVITY RM. SINGLE Yes No YES SPECIAL #1 Yes No CONNECTED TO EXISITING

EMERGENCY ALARM.142D No No143 RN OFFICE SINGLE Yes No GC - KEYED AREA 1 No Yes144 DEBRIEF / LUNCH SINGLE Yes No GC - KEYED AREA 3 No Yes145 CLINIC EXAM RM. SINGLE Yes No GC - KEYED AREA 1 No Yes146 CLINIC EXAM RM. SINGLE Yes No GC - KEYED AREA 1 No Yes147 CLINIC EXAM RM. SINGLE Yes No GC - KEYED AREA 1 No Yes148 CLINIC EXAM RM. SINGLE Yes No GC - KEYED AREA 1 No Yes149 W/R SINGLE Yes No No No150 DOCTOR'S OFFICE SINGLE Yes No GC - KEYED AREA 1 No Yes151 MED SINGLE Yes No GC - KEYED AREA 5 No Yes152 CLINIC EXAM RM. SINGLE Yes No GC - KEYED AREA 1 No Yes153 SUPPLY SINGLE Yes No GC - KEYED AREA 1 No Yes154 CLINIC EXAM RM. SINGLE Yes No GC - KEYED AREA 1 No Yes155 BILLING / STATS CLERK SINGLE Yes No GC - KEYED AREA 1 No Yes158 W/R SINGLE Yes No No No160 LAB SUPPLY SINGLE Yes No GC - KEYED AREA 1 No Yes162 SR RN SINGLE Yes No GC - KEYED AREA 1 No Yes164 MGR SINGLE Yes No GC - KEYED AREA 1 No Yes167 CORRIDOR SINGLE Yes No No No REMOVE DOOR. SEE

RENOVATION NOTE 12167A CORRIDOR SINGLE Yes Yes Yes No REVERSE DOOR SWING

FOR BARRIER FREEREQUIREMENTS

168A VEST. SINGLE Yes No SPECIAL #1 Yes No POWER DOOR OPERATOR168B VEST. SINGLE Yes No SPECIAL #1 Yes No POWER DOOR OPERATOR169 NIS SINGLE Yes No No No170 W/R SINGLE Yes No No No REVERSE DOOR SWING

FOR BARRIER FREEREQUIREMENTS

171 STAIR SINGLE No Yes SPECIAL #1 Yes No ALARM179 RECEPTION OFFICE SINGLE Yes No SPECIAL #1 Yes NoX104 STAIR DOUBLE Yes No YES No NoX105 STAIR SINGLE Yes No YES No NoX106 STAIR DOUBLE Yes No No No

Room Finish Schedule - New Construction

NO Room Name Sink Floor Lighting WindowsComments

121 HEALTH PROMOTION RM.123 HEALTH PROMOTION OFF.129 ALLIED HEALTH PROF. FILM BOTTOM HALF SEE RENOVAION NOTE R02130 COUNSELLOR OFFICE FILM BOTTOM HALF SEE RENOVAION NOTE R02131 PSYCHIATRIST FILM BOTTOM HALF SEE RENOVAION NOTE R02132 SR. COUNSELLOR OFFICE FILM BOTTOM HALF SEE RENOVAION NOTE R02133 CLINIC MH ASSESSMENT FILM BOTTOM HALF SEE RENOVAION NOTE R02137 DIRTY UTILITY LED138 COUNSELLOR OFFICE FILM BOTTOM HALF SEE RENOVAION NOTE R02139 TRIAGE NEW LED FILM BOTTOM HALF /

FULL WINDOWSEE RENOVAION NOTE R02 & R08

140 COUNSELLOR OFFICE FILM BOTTOM HALF SEE RENOVAION NOTE R02141 OBSERVATION RM. FILM BOTTOM HALF /


142 GROUP ACTIVITY RM.143 RN OFFICE LED FILM BOTTOM HALF SEE RENOVAION NOTE R02144 DEBRIEF / LUNCH LED145 CLINIC EXAM RM. NEW LED FILM BOTTOM HALF /


146 CLINIC EXAM RM. NEW LED FILM BOTTOM HALF SEE RENOVAION NOTE R02147 CLINIC EXAM RM. NEW LED FILM BOTTOM HALF /


148 CLINIC EXAM RM. NEW LED FILM BOTTOM HALF /FULL WINDOW

SEE RENOVAION NOTE R02 & R08

149 W/R150 DOCTOR'S OFFICE LED151 MED NEW152 CLINIC EXAM RM. NEW LED FILM BOTTOM HALF /


153 SUPPLY154 CLINIC EXAM RM. NEW LED FILM BOTTOM HALF SEE RENOVAION NOTE R02155 BILLING / STATS CLERK158 W/R160 LAB SUPPLY LED162 SR RN164 MGR167 CORRIDOR PAINT WALLS, SEE RENOVATION NOTE R06168 VEST.170 W/R BARRIER FREE179 RECEPTION OFFICE LED FILM BOTTOM HALF INSTALL 2 TELLER OPENINGSX104 STAIRX105 STAIRX106 STAIRX115 CORRIDORX115A CORRIDOR TILEX116 WAITING AREA

08 71 00 HARDWARE

GENERAL

SUBMIT MANUFACTURER’S PRINTED PRODUCTLITERATURE, SPECIFICATIONS AND DATA SHEET INACCORDANCE WITH SECTION [01 33 00 -SUBMITTALS].

SUBMIT SAMPLES IN ACCORDANCE WITH SECTION[01 33 00 SUBMITTALS].

IDENTIFY EACH SAMPLE BY LABEL INDICATINGAPPLICABLE SPECIFICATION PARAGRAPH NUMBER,BRAND NAME AND NUMBER, FINISH AND HARDWAREPACKAGE NUMBER.

AFTER APPROVAL SAMPLES WILL BE RETURNED FORINCORPORATION IN THE WORK.

SUBMIT CONTRACT HARDWARE LIST IN ACCORDANCEWITH SECTION [01 33 00 SUBMITTALS].

INDICATE SPECIFIED HARDWARE, INCLUDING MAKE,MODEL, MATERIAL, FUNCTION, SIZE, FINISH ANDOTHER PERTINENT INFORMATION.

SUBMIT MANUFACTURER’S INSTALLATIONINSTRUCTIONS.

PROVIDE OPERATION AND MAINTENANCE DATA FORDOOR CLOSERS, LOCKSETS, DOOR HOLDERS,ELECTRIFIED HARDWARE AND FIRE EXIT HARDWAREFOR INCORPORATION INTO MANUAL SPECIFIED INSECTION [01 78 23 OPERATION AND MAINTENANCEMANUALS].

QUALITY ASSURANCE

HARDWARE FOR DOORS IN FIRE SEPARATIONS ANDEXIT DOORS CERTIFIED BY A CANADIANCERTIFICATION ORGANIZATION ACCREDITED BYSTANDARDS COUNCIL OF CANADA.

TEST REPORTS: CERTIFIED TEST REPORTS SHOWINGCOMPLIANCE WITH SPECIFIED PERFORMANCECHARACTERISTICS AND PHYSICAL PROPERTIES.

CERTIFICATES: PRODUCT CERTIFICATES SIGNED BYMANUFACTURER CERTIFYING MATERIALS COMPLYWITH SPECIFIED PERFORMANCE CHARACTERISTICSAND CRITERIA AND PHYSICAL REQUIREMENTS.

PRE-INSTALLATION MEETINGS: CONDUCT PRE-INSTALLATION MEETING TO VERIFY PROJECTREQUIREMENTS, MANUFACTURER’S INSTALLATIONINSTRUCTIONS AND MANUFACTURER’S WARRANTYREQUIREMENTS.

DELIVERY, STORAGE, AND HANDLING

DELIVER, STORE, HANDLE AND PROTECT MATERIALSIN ACCORDANCE WITH SECTION [01 60 00 - PRODUCTREQUIREMENTS].

PACKAGE EACH ITEM OF HARDWARE INCLUDINGFASTENINGS, SEPARATELY OR IN LIKE GROUPS OFHARDWARE, LABEL EACH PACKAGE AS TO ITEMDEFINITION AND LOCATION.

STORE FINISHING HARDWARE IN LOCKED, CLEANAND DRY AREA.

MAINTENANCE

PROVIDE MAINTENANCE MATERIALS IN ACCORDANCEWITH SECTION [01 78 23 OPERATION ANDMAINTENANCE MANUALS].

SUPPLY TWO SETS OF WRENCHES FOR DOORCLOSERS, LOCKSETS AND FIRE EXIT HARDWARE.

MATERIAL

HARDWARE ITEMS:

USE THE MANUFACTURER’S AS STATED BELOWWITHOUT ALTERNATIVES FOR SIMILAR ITEMS.

DOOR HARDWARE:

LOCKSETS: SCHLAGE ORIGINAL (NOT OFF-SHORE)WITH GRADE 1 CERTIFICATION, LEVER SETS, 626FINISH.

CYLINDERS: SCHLAGE ORIGINAL FG KEYWAY ZEROPINNED TO BE PROVIDED TO LU FOR PINNING.CONTRACTOR TO MAINTAIN SECURITY WITH THEIROWN CONSTRUCTION CORES THAT WILL BESWAPPED OUT BY LU WITH PINNED CYLINDERS. LUHAS REQUESTED NON REMOVEABLE CORES.

INTERIOR DOORS: SUPPLIED CYLINDERS TO BE 1248TYPE.

EXTERIO DOORS: SUPPLIED CYLINDERS TO "T"KEYAY.

EXIT DEVICES: VON DUPRIN 98.

DOOR CLOSERS: VON DUPRIN 4041.

FASTENINGS

USE ONLY FASTENERS PROVIDED BYMANUFACTURER. FAILURE TO COMPLY MAY VOIDWARRANTIES AND APPLICABLE LICENSED LABELS.

SUPPLY SCREWS, BOLTS, EXPANSION SHIELDS ANDOTHER FASTENING DEVICES REQUIRED FORSATISFACTORY INSTALLATION AND OPERATION OFHARDWARE.

EXPOSED FASTENING DEVICES TO MATCH FINISH OFHARDWARE.

WHERE PULL IS SCHEDULED ON ONE SIDE OF DOORAND PUSH PLATE ON OTHER SIDE, SUPPLYFASTENING DEVICES, AND INSTALL SO PULL CAN BESECURED THROUGH DOOR FROM REVERSE SIDE.

INSTALL PUSH PLATE TO COVER FASTENERS.

USE FASTENERS COMPATIBLE WITH MATERIALTHROUGH WHICH THEY PASS.

KEYING

DOORS, PADLOCKS AND CABINET LOCKS TO BEKEYED AS DIRECTED. PREPARE DETAILED KEYINGSCHEDULE IN CONJUNCTION WITH UNIVERSITYREPRESENTATIVE.

PROVIDE KEYS IN DUPLICATE FOR EVERY LOCK INTHIS CONTRACT.

PROVIDE THREE MASTERKEYS FOR EACH MK ORGMK GROUP.

STAMP KEYING CODE NUMBERS ON KEYS ANDCYLINDERS.

PROVIDE CONSTRUCTION CORES.

PROVIDE ALL PERMANENT CORES AND KEYS TOUNIVERSITY REPRESENTATIVE.

INSTALLATION

COMPLIANCE: COMPLY WITH MANUFACTURER’SWRITTEN DATA, INCLUDING PRODUCT TECHNICALBULLETINS, PRODUCT CATALOGUE INSTALLATIONINSTRUCTIONS, PRODUCT CARTON INSTALLATIONINSTRUCTIONS, AND DATA SHEETS.

FURNISH METAL DOOR AND FRAMEMANUFACTURERS WITH COMPLETE INSTRUCTIONSAND TEMPLATES FOR PREPARATION OF THEIRWORK TO RECEIVE HARDWARE.

FURNISH MANUFACTURERS’ INSTRUCTIONS FORPROPER INSTALLATION OF EACH HARDWARECOMPONENT.

INSTALL HARDWARE TO STANDARD HARDWARELOCATION DIMENSIONS IN ACCORDANCE WITHCANADIAN METRIC GUIDE FOR STEEL DOORS ANDFRAMES (MODULAR CONSTRUCTION) PREPAREDBY CANADIAN STEEL DOOR AND FRAMEMANUFACTURERS’ ASSOCIATION.

WHERE DOOR STOP CONTACTS DOOR PULLS,MOUNT STOP TO STRIKE BOTTOM OF PULL.INSTALL KEY CONTROL CABINET.

USE OF “QUICK” TYPE FASTENERS, UNLESSSPECIFICALLY SUPPLIED BY MANUFACTURER, ISUNACCEPTABLE.

REMOVE CONSTRUCTION CORES AND LOCKSWHEN DIRECTED BY UNIVERSITYREPRESENTATIVE; INSTALL PERMANENT CORESAND CHECK OPERATION OF LOCKS.

ADJUST DOOR HARDWARE, OPERATORS,CLOSURES AND CONTROLS FOR OPTIMUM,SMOOTH OPERATING CONDITION, SAFETY AND FORWEATHER TIGHT CLOSURE.

LUBRICATE HARDWARE, OPERATING EQUIPMENTAND OTHER MOVING PARTS.

ADJUST DOOR HARDWARE TO PROVIDE TIGHT FITAT CONTACT POINTS WITH FRAMES.

CLEANING

PERFORM CLEANING AFTER INSTALLATION TOREMOVE CONSTRUCTION AND ACCUMULATEDENVIRONMENTAL DIRT.

CLEAN HARDWARE WITH DAMP RAG ANDAPPROVED NON-ABRASIVE CLEANER, AND POLISHHARDWARE IN ACCORDANCE WITHMANUFACTURE’S INSTRUCTIONS.

REMOVE PROTECTIVE MATERIAL FROM HARDWAREITEMS WHERE PRESENT.

UPON COMPLETION OF INSTALLATION, REMOVE

KEYING SYSTEM SETUP AND CABINET:

SET UP KEY CONTROL SYSTEM WITH FILE KEY TAGS,DUPLICATE KEY TAGS, NUMERICAL INDEX,ALPHABETICAL INDEX AND KEY CHANGE INDEX, LABELSHIELDS, CONTROL BOOK AND KEY RECEIPT CARDS.

PLACE FILE KEYS AND DUPLICATE KEYS IN KEYCABINET ON THEIR RESPECTIVE HOOKS.LOCK KEY CABINET AND TURN OVER KEY TOUNIVERSITY REPRESENTATIVE.

MAINTENANCE STAFF BRIEFING:

BRIEF MAINTENANCE STAFF REGARDING:

PROPER CARE, CLEANING, AND GENERALMAINTENANCE OF PROJECTS COMPLETE HARDWARE.DESCRIPTION, USE, HANDLING, AND STORAGE OFKEYS.

USE, APPLICATION AND STORAGE OF WRENCHESFOR DOOR CLOSERS, LOCKSETS AND FIRE EXITHARDWARE.

DEMONSTRATE OPERATION, OPERATINGCOMPONENTS, ADJUSTMENT FEATURES, ANDLUBRICATION REQUIREMENTS.

DIVISION 9 - FINISHES

09 21 16 - GYPSUM BOARD

GENERAL

INSTALL WORK TO A LEVEL OF TOLERANCE TO1:1200.

DO NOT APPLY GYPSUM BOARD UNTIL BUCKS,ANCHORS, BLOCKING, SOUND ATTENUATION,ELECTRICAL AND MECHANICAL WORK AREAPPROVED.

APPLY SINGLE/DOUBLE LAYER GYPSUM BOARD TOWOOD OR METAL FURRING OR FRAMING USINGSCREW FASTENERS. MAXIMUM SPACING OFSCREWS 300 MM OC.

SINGLE-LAYER APPLICATION:

APPLY GYPSUM BOARD ON CEILINGS PRIOR TOAPPLICATION OF WALLS IN ACCORDANCE WITHASTM C840.

APPLY GYPSUM BOARD VERTICALLY ORHORIZONTALLY, PROVIDING SHEET LENGTHS THATWILL MINIMIZE END JOINTS.

DOUBLE LAYER APPLICATION:

INSTALL GYPSUM BOARD FOR BASE LAYER ANDEXPOSED GYPSUM BOARD FOR FACE LAYER.

APPLY BASE LAYER TO CEILINGS PRIOR TO BASELAYER APPLICATION ON WALLS; APPLY FACELAYERS IN SAME SEQUENCE. OFFSET JOINTSBETWEEN LAYERS AT LEAST 250 MM.

APPLY BASE LAYERS AT RIGHT ANGLES TOSUPPORTS UNLESS OTHERWISE INDICATED.

APPLY BASE LAYER ON WALLS AND FACE LAYERSVERTICALLY WITH JOINTS OF BASE LAYER OVERSUPPORTS AND FACE LAYER JOINTS OFFSET ATLEAST 250 MM WITH BASE LAYER JOINTS.

APPLY 12 MM DIAMETER BEAD OF ACOUSTICSEALANT CONTINUOUSLY AROUND PERIPHERY OFEACH FACE OF PARTITIONING TO SEAL GYPSUMBOARD/STRUCTURE JUNCTION WHEREPARTITIONS BUTT AGAINST FIXED BUILDINGCOMPONENTS. SEAL FULL PERIMETER OF CUT-OUTS AROUND ELECTRICAL BOXES, DUCTS, INPARTITIONS WHERE PERIMETER SEALED WITHACOUSTIC SEALANT.

INSTALL GYPSUM BOARD WITH FACE SIDE OUT.DO NOT INSTALL DAMAGED OR DAMP BOARDS.

LOCATE EDGE OR END JOINTS OVER SUPPORTS.STAGGER VERTICAL JOINTS OVER DIFFERENTSTUDS ON OPPOSITE SIDES OF WALL.

MATERIAL

DRYWALL INSTALLER MINIMUM 5 YRSEXPERIENCE.

BOARD: 1/2" THICK STANDARD, 5/8" THICK TYPE X,4' WIDE x MAXIMUM PRACTICAL LENGTH, ENDSSQUARE CUT, EDGES BEVELED, REFER TODRAWINGS FOR LOCATIONS.

GLASS MAT WATER-RESISTANT GYPSUM BOARD:TO ASTM C1178/C1178M WITH GLASS MATFACINGS, BOTH SIDES, REGULAR AND TYPE X,THICKNESS AS INDICATED ON DRAWINGS, 1200MM WIDE X MAXIMUM PRACTICAL LENGTH, ENDSSQUARE CUT, LONG EDGES TAPERED.

METAL FURRING RUNNERS, HANGERS, TIE WIRES,INSERTS, ANCHORS: TO CSA A82.30 GALVANIZED.

DRYWALL FURRING CHANNELS: 0.5 MM CORETHICKNESS GALVANIZED STEEL CHANNELS FORSCREW ATTACHMENT OF GYPSUM BOARD.

STEEL DRILL SCREWS: TO ASTM 1002.

LAMINATING COMPOUND AS RECOMMENDED BYMANUFACTURER - ASBESTOS FREE.

CASING BEADS, CORNER BEADS, AND EDGE TRIMTO ASTM-C 1047; METAL ZINC COATED; 14 ga BASETHICKNESS, PERFORATED FLANGES, ONE PIECE,UNLESS OTHERWISE SPECIFIED ON DRAWINGS.

SEALANTS IN ACCORDANCE TO CAN/CGSB - 19.21-M87

JOINT COMPOUNDS TO ASTM-C 475, ASBESTOSFREE.

INSTALLATION

ERECT ACCESSORIES STRAIGHT, PLUMB ORLEVEL, RIGID AND AT PROPER PLANE. USE FULLLENGTH PIECES WHERE PRACTICAL. MAKEJOINTS TIGHT, ACCURATELY ALIGNED ANDRIGIDLY SECURED. MITER AND FIT CORNERSACCURATELY, FREE FROM ROUGH EDGES.SECURE AT 150 MM OC USING CONTACTADHESIVE FOR FULL LENGTH.

INSTALL CASING BEADS AROUND PERIMETER OFSUSPENDED CEILINGS.

INSTALL CASING BEADS WHERE GYPSUM BOARDBUTTS AGAINST SURFACES HAVING NO TRIMCONCEALING JUNCTION AND WHERE INDICATED.SEAL JOINTS WITH SEALANT.

INSTALL ACCESS DOORS TO ELECTRICAL ANDMECHANICAL FIXTURES SPECIFIED INRESPECTIVE SECTIONS.RIGIDLY SECURE FRAMES TO FURRING ORFRAMING SYSTEMS.

FINISH FACE PANEL JOINTS AND INTERNALANGLES WITH JOINT SYSTEM CONSISTING OFJOINT COMPOUND, JOINT TAPE AND TAPINGCOMPOUND INSTALLED ACCORDING TOMANUFACTURER'S DIRECTIONS AND FEATHEREDOUT ONTO PANEL FACES.

GYPSUM BOARD FINISH: FINISH GYPSUM BOARDWALLS TO FOLLOWING LEVELS IN ACCORDANCEWITH ASSOCIATION OF THE WALL AND CEILINGINDUSTRIES (AWCI) INTERNATIONALRECOMMENDED SPECIFICATION ON LEVELS OFGYPSUM BOARD FINISH:

LEVELS OF FINISH:

LEVEL 2: EMBED TAPE FOR JOINTS AND INTERIORANGLES IN JOINT COMPOUND AND APPLY ONESEPARATE COAT OF JOINT COMPOUND OVERJOINTS, ANGLES, FASTENER HEADS ANDACCESSORIES; SURFACES FREE OF EXCESSJOINT COMPOUND; TOOL MARKS AND RIDGES AREACCEPTABLE.(FOR USE WHERE WATERRESISTANT GYPSUM BACKING BOARD IS USED ASA SUBSTRATE FOR TILE.)

LEVEL 4: EMBED TAPE FOR JOINTS AND INTERIORANGLES IN JOINT COMPOUND AND APPLY THREESEPARATE COATS OF JOINT COMPOUND OVERJOINTS, ANGLES, FASTENER HEADS ANDACCESSORIES; SURFACES SMOOTH AND FREE OFTOOL MARKS AND RIDGES.

FINISH CORNER BEADS, CONTROL JOINTS ANDTRIM AS REQUIRED WITH TWO COATS OF JOINTCOMPOUND AND ONE COAT OF TAPINGCOMPOUND, FEATHERED OUT ONTO PANELFACES.

FILL SCREW HEAD DEPRESSIONS WITH JOINTAND TAPING COMPOUNDS TO BRING FLUSH WITHADJACENT SURFACE OF GYPSUM BOARD SO ASTO BE INVISIBLE AFTER SURFACE FINISH ISCOMPLETED.

SAND LIGHTLY TO REMOVE BURRED EDGES ANDOTHER IMPERFECTIONS. AVOID SANDINGADJACENT SURFACE OF BOARD.

COMPLETED INSTALLATION TO BE SMOOTH,LEVEL OR PLUMB, FREE FROM WAVES AND OTHERDEFECTS AND READY FOR SURFACE FINISH.

APPLY ONE COAT OF WHITE PRIMER SEALEROVER SURFACE TO BE TEXTURED. WHEN DRYAPPLY TEXTURED FINISH IN ACCORDANCE WITHMANUFACTURER'S INSTRUCTIONS.

MIX JOINT COMPOUND SLIGHTLY THINNER THANFOR JOINT TAPING.

APPLY THIN COAT TO ENTIRE SURFACE USINGTROWEL OR DRYWALL BROADKNIFE TO FILLSURFACE TEXTURE DIFFERENCES, VARIATIONSOR TOOL MARKS.

ALLOW SKIM COAT TO DRY COMPLETELY.REMOVE RIDGES BY LIGHT SANDING OR WIPINGWITH DAMP CLOTH.

PROVIDE PROTECTION THAT ENSURES GYPSUMDRYWALL WORK WILL REMAIN WITHOUT DAMAGEOR DETERIORATION AT TIME OF SUBSTANTIALCOMPLETION.

CONSTRUCT FIRE RATED ASSEMBLIES WHEREINDICATED, SEAL PENETRATIONS

09 91 00 PAINTING

GENERAL

SAND AND DUST BETWEEN EACH COAT TO REMOVEDEFECTS VISIBLE FROM A DISTANCE OF UP TO 1220mm.FINISH BOTTOMS, EDGES, TOPS AND CUT OUTS OFDOORS, AFTER FITTING AS SPECIFIED FOR DOORSURFACES.

REMOVE COVER PLATES ETC BEFORE PAINTING,REPLACE UPON COMPLETION.

FIRE SAFETY REQUIREMENTS

MATERIAL

PAINTING TO THE LATEST EDITION OF THEARCHITECTURAL PAINTING SPECIFICATIONSMANUAL BY THE MASTER PAINTERS INSTITUTE.

OWNER’S REPRESENTATIVE WILL PROVIDE COLOURSCHEDULE AFTER CONTRACT AWARD

INTERIOR PAINTING SYSTEMS

THE FOLLOWING PAINT FORMULAS REQUIRES ATHREE COAT FINISH AS INDICATED IN THE MPIARCHITECTURAL PAINTING SPECIFICATIONSMANUAL.

HIGH GLOSS ENAMEL. COLOR TO BE SELECTED BYCONSULTANT.

RECEPTION AREA

INT 5.3A LATEX G5 FINISH.

PLASTER AND GYPSUM BOARD: GYPSUMWALLBOARD, DRYWALL, “SHEET ROCK TYPEMATERIAL”, ETC AND TEXTURED FINISHES:INT 9.2A LATEX G5 FINISH (OVER LATEX SEALER)FOR WALLS.INT 9.2A LATEX G1 FINISH (OVER LATEX SEALER)FOR CEILINGS.

SUBMIT ONE - FOUR LITER CAN OF EACH TYPE ANDCOLOUR OF FINISH COATING. IDENTIFY COLOURAND PAINT TYPE IN RELATION TO ESTABLISHEDCOLOUR SCHEDULE AND FINISH FORMULA

INSTALLATION

CONTRACTOR SHALL HAVE A MINIMUM OF FIVEYEARS PROVEN SATISFACTORY EXPERIENCE.CONFORM TO LATEST MPI REQUIREMENTS FORINTERIOR PAINTING WORK INCLUDINGPREPARATION AND PRIMING.

PERFORM PREPARATION AND OPERATIONS FORINTERIOR PAINTING IN ACCORDANCE WITH MPIPAINTING SPECIFICATIONS MANUAL EXCEPT WHERESPECIFIED OTHERWISE.

SURFACE PREPARATIONCLEAN AND PREPARE SURFACES IN ACCORDANCEWITH MPI PAINTING SPECIFICATION MANUALREQUIREMENTS.

PREPARE PLASTER AND WALLBOARD SURFACES TOCGSB 85-GP-33M. FILL MINOR CRACKS WITHPLASTER PATCHING COMPOUND.

164

MGR

155

BILLING /STATSCLERK

162

SR RN

160

LABSUPPLY

158

W/R

154

CLINICEXAM RM.

152

CLINICEXAM RM. 150

DOCTOR'SOFFICE

148

CLINICEXAM RM.

146

CLINICEXAM RM.

153

SUPPLY

151

MED

149

W/R

147

CLINICEXAM RM.

145

CLINICEXAM RM.

143

RN OFFICE

141

OBSERVATIONRM.

139

TRIAGE 137

DIRTYUTILITY

140COUNSELLOR

OFFICE

133CLINIC MH

ASSESSMENT

138COUNSELLOR

OFFICE

131PSYCHIATRIST

129

ALLIED

HEALTH

PROF.

132

SR.

COUNSELLOR

OFFICE

130COUNSELLOR

OFFICE

123

HEALTH

PROMOTION

OFF.

121

HEALTH

PROMOTION

RM.

X104STAIR

X105STAIR

X106

STAIR

NOT IN SCOPE

65 m²142

GROUP ACTIVITY RM.

X115CORRIDOR

116

X104

104

123 121

130

132

138

140

133 131

129

115

105

142

144

137

148 146

139141143

150152

145147

154158

149151

160162

153

164

155

106

X106155

164

NIS

NIS

NIS

NIS

NIS

179

RECEPTION

OFFICE

X116

WAITINGAREA

179

X105

R03

R02

R02

R02

R02

R02

R02

R02

R02

R02

5' - 0"

R05

R02

R02

R02

R02 R02

R02

64 m²X115A

CORRIDOR

16 m²144

DEBRIEF / LUNCH

R04

A3

2

1A3

A33

D01

D02

EXISTING CARPET

TO REM

AIN IN CORRIDO

R

ALARM AT

STAIRWELL.

REFER TO

ELEC.

EQ. EQ.

EQ. EQ.

R05EQ. EQ.

R05EQ. EQ.

EQ. EQ.EQ.

R05R05

R07 R07 R07

8' - 8"

SITE VERIFY

16' - 7 1/4"

NOT IN SCOPE

NOT IN SCOPE

INSTALL NEW RAMP AT A 1:20SLOPE. INSTALL EXPANSION JOINTBETWEEN NEW AND EXISTINGCONSTRUCTION. CONTRACTOR TOCONFIRM EXISTING ELEVATIONSFOR RAMP LENGTH.

5' - 5"

R05

R07

EQ.EQ.

R05EQ. EQ.

R07

EQ. R07

R08

R08R08

R08

R08

R08

R09

R09

R09

R09R09

R09R10

R10R10

R10R10

R10

R10 R10 R10 R10

R10 R10 R10

R10 R10 R10

R10

R10 R10

R10 R10 R10 R10 R10R10

R10

5' - 4"

UP

LINE SHOWING EXISTINGCURB.

R08

6' - 1"

R11

R12

R11

R14

167

CORRIDOR

168

VEST.

NIS

170

W/R

168A

168B

R15

170

169

167

115A

142A

142B

R13

R03D02

R05

R10R10

R16

R10 R10 R10

R16 R16

R10 R10 R10 R10

R16

R10

R10

R10

R16

R17

4A4

2A4

1A4

3A4

2A2

A

BC

DE

F

G H

I

J

K

L

M

MOUNT BARRIER FREE PUSHBUTTONSAS PER OBC BARRIER FREE

REQUIREMENTS.

R19

R19

R19 R19

R19 R19R19R19

R06

R06

167A

1' - 1 3/4"

2' -

8 3/

4"

DN

UP

171

111

A23

R06

9 WINDOWS TO BE COVERED IN PRIVACY WINDOW FILM.REFER TO RENOVATION NOTE R02.

R01

246

Dorm Room

1' - 6"R18

5' - 4" 16' - 7 1/4"

INSTALL NEW CONCRETE RAMP AT A 1:20 SLOPE. INSTALLEXPANSION JOINT BETWEEN NEW AND EXISTING CONSTRUCTION.CONTRACTOR TO CONFIRM EXISTING ELEVATIONS FOR RAMPLENGTH.

21' - 11 1/4"

EXISTING FURNITURE INVENTORY

ITEM TYPE WIDTH DEPTH HEIGHT CURRENT LOCATION NEW LOCATION

A RN LOCKER 24" 16" 77" UC1007AK 162

B MED CABINET 30" 12.5" 30.5" CENTRE HALL 151

C MED CABINET 30" 12.5" 30.5" CENTRE HALL 151

D MED CABINET 30" 12.5" 30.5" CENTRE HALL 151

E MED CABINET 30" 12.5" 30.5" CENTRE HALL 151

F OPEN CABINET 36 5/8" 18.25" 84" 1007AK 151

G OPEN CABINET 36 5/8" 18.25" 84" MAIN CENTRE HALL 153

H OPEN CABINET 36 5/8" 18.25" 84" MAIN CENTRE HALL 153

I CLOSED CABINET 36 5/8" 18" 84" 1007A1 153

J LAB CABINETS 30" 13" 30.5" BATHROOM 137

K LAB CABINETS 30" 13" 30.5" BATHROOM 137

L COUNTER 59.25" 15" CENTRE HALL 149

M OPEN CABINET 36 5/8" 18.25" 84" 1007AK 121

NOTE: LAKEHEAD UNIVERSITY TO MOVE EXISTING FURNITURE.




3 01/23/2015 FOR TENDER

8' -

0"

7' -

0"0'

- 8"3' - 0"2' - 8 3/4" 2' - 8 3/4"

9' - 1 1/2"

RATED HOLLOW METALDOOR AND FRAME.

GEORGIAN WIRED GLASS.2' -

9"0'

- 2" SUPPLY AND INSTALL NEW GRAB BARS TO MEET

BARRIER FREE REQ.

BOBRICK 600 GRAB BAR - FROST CODE 1003 ORAPPROVED EQUAL.

BOBRICK 760 X 760 GRAB BAR - FROST CODE1003 OR EQUAL

NOTE: GRAB BARS TO BE:1. INSTALLED TO RESIST A LOAD OF AT LEAST1.3KN APPLIED HORIZONTALLY OR VERTICALLY2. DIAMETER TO BE BETWEEN 30MM AND 40MM3. HAVE A CLEARANCE OF 30MM TO 40MMFROM THE WALL, AND4. HAVE A SLIP RESISTANT SURFACE

ENSURE ADEQUATE BLOCKING HAS BEENINSTALLED AS PER MANUFACTURERSINSTRUCTIONS

1' -

11 3

/4"

2' -

9 5/

8"

DATE


T. 807 683 8005 F. 416 504 7712


SHEET NO.

DRAWN

PROJECT NO.

SHEET TITLE


CLIENT

PROJECT NAME


BrookMcIlroy/

1/22

/201

5 4:

53:0

2 PM

V:\2

012\

TB -

12-0

26-L

akeh

ead

Uni

vers

ity -

Arch

Ser

vice

s\12

-026

.13

- Hea

lth &

Cou

nsel

ling

Cen

tre (P

retti

e R

esid

ence

)\B -

Dw

gs +

Imag

es\B

2 D

raw

ings

\B2.

0 R

evit\

12-1

26.1

3 H

ealth

& C

ouns

ellin

g C

entre

(Pre

ttie

Res

iden

ce) -

Jan

14

2015

.rvt


Renovation Plan

12-026.13

VLD

JANUARY 2015

A2


1/8" = 1'-0"1 Renovation Plan

Renovation NotesMark DescriptionR01 PROVIDE AND INSTALL LOW RISE DOOR STOP BY STANLEY OR APPROVED

EQUALR02 ADD 3M FASARA GLASS AND PLASTIC WINDOW FILM OR APPROVED EQUAL TO

BOTTOM HALF OF WINDOW AS PER THE MANUFATURERS INSTALLATIONGUIDE, REVISION C, FEBRUARY 2014.

R03 INSTALL NEW TELLER OPENING INTO EXISTING WALL.R04 INSTALL NEW FLOORING:FORBO MARMOLEUM (2621 DOVE GREY)

HOMOGENOUS SHEET FLOORING AS PER THE MANUFACTURERSCOMMERCIAL INSTALLATION GUIDE OR APPROVED EQUAL. INSTALL 4"RUBBER WALL BASE COLOR TO BE SELECTED BY CONSULTANT

R05 INSTALL NEW SINK, REFER TO MECHANICAL DRAWING M1-PARTIAL MAINFLOOR PLAN DEMOLITION AND RENOVATION PLAN.

R06 PAINT EXISTING BRICK AND BLOCK WALL.R07 REMOVE EXISTING MILLWORK AND ADD NEW 2X6 METAL STUD PLUMBING

WALL WITH 1/2" GWB. PREPARE WALL FOR WALL MOUNTED WASH BASIN.PAINT TO MATCH EXISTING FINISHES.

R08 ADD 3M FASARA GLASS AND PLASTIC WINDOW FILM OR APPROVED EQUAL TOENTIRE WINDOW AS PER THE MANUFATURERS INSTALLATION GUIDE,REVISION C, FEBRUARY 2014.

R09 EXISTING FURNITURE FROM CURRENT MEDICAL CENTRE. LAKEHEADUNIVERSITY TO MOVE FURNITURE FROM EXISITNG SPACE TO NEWRENOVATED SPACE, NIC.

R10 EXISTING MILLWORK TO REMAIN.R11 REMOVE EXISTING MILLWORK PATCH AND MAKE GOOD. CLEAN AFFECTED

BLOCK WALL SURFACE WITH WIRE BRUSH, PATCH AS REQUIRED, GRIND ANDSAND TO MATCH SURFACE OF EXISTING. REMOVE PATCH FROM ANY JOINTSAND GROUT. PAINT AS INDICATED IN RENOVATION R06.

R12 REMOVE EXISTING DOOR AND FRAME. CLEAN AFFECTED BLOCK WALLSURFACE WITH WIRE BRUSH, PATCH AS REQUIRED, GRIND AND SAND TOMATCH SURFACE OF EXISTING. REMOVE PATCH FROM ANY JOINTS ANDGROUT. PAINT AS INDICATED IN RENOVATION R06.

R13 NEW STUD WALL TO MATCH EXISTING. REGISTER NEW WALL WITH EXISTING,PATCH AND MAKE GOOD. MAINTAIN EXISTING FIRE RATINGS.

R14 INSTALL CRUTCH HANGER. LAKEHEAD UNIVERSITY TO CONFIRM LOCATION.R15 REMOVE EXISTING TOILET PARTITIONS. PATCH FLOOR, WALL AND MAKE

GOOD.R16 INSTALL 8" WOOD EXTENSION TO EXISTING COUNTER TOPS. CONTRACTOR

TO CONFIRM SUITABLE LOCATION FOR WOOD SUPPORTS. SEE DRAWING A4.R17 INSTALL NEW 3 1/2" METAL STUD WALL WITH ACOUSTIC BATT INSULATION

AND 1 LAYER OF 15.9 MM TYPE X GYPSUM BOARD ON BOTH SIDES. ALIGNNEW WALL WITH EXISTING SURFACES, PATCH AND MAKE GOOD. MAINTAINEXISTING FIRE RATING.

R18 REMOVE EXISTING MILLWORK AND ADD NEW 2X6 METAL PLUMBING CHASEWITH GWB FINISH. MAINTAIN FIRE RATING AND PAINT TO MATCH EXISTINGFINISH.

R19 INSTALL EXISTING PRIVACY CURTAINS. COORDINATE LOCATION WITH LU

Demolition NotesMark DescriptionD01 REMOVE EXISTING FLOORING AND BASELAYER AND PREPARE SURFACE FOR

INSATLLATION OF FORBO MARMOLEUM (2621 DOVE GREY) HOMOGENOUSSHEET FLOORING AS PER THE MANUFACTURERS COMMERCIALINSTALLATION GUIDE.

D02 CREATE OPENING IN EXISTING WALL AND PREPARE FOR INTSTALLATION OFTELLER WINDOW AS SHOWN ON DRAWING A3 - SECTION AT RECEPTIONAREA. PATCH AND MAKE GOOD ANY AFFECTED SURFACES.

1/8" = 1'-0"4

Partial Second Floor Plan - MechanicalChase Layout

3/8" = 1'-0"2 Ramp Section

1/4" = 1'-0"3 Interior Glazing and Frame 1/4" = 1'-0"5 W/R 170 Interior Elevation

4A3

BARRIER-FREE

7' - 4"

3' - 0" 3' - 0"

5' - 0"

7' - 4"

RO

UG

H O

PEN

ING

4' -

0"

4A3

179

RO

UG

H O

PEN

ING

4' -

6 3/

8"

ROUGH OPEING

3' - 0"

ROUGH OPENING

3' - 0"

OPENING

OPENING

GLAZINGGLAZING

0' - 6" 1' - 7 1/2" 0' - 6"

0' -

8"

BAR

RIE

R F

REE

2' -

9 7/

8"3' -

3"

5' - 0"

0' -

8"

0' - 6" 1' - 7 1/2" 0' - 6"

CLEAR PINE RECEPTION COUNTER AND PRIVACYSCREEN TYP.

STATIONARY TEMPERED 1/4" CLEAR GLASS WINDOWWITH 3/4" CLEAR PINE TRIM TYP.

OPENING IN GLASS WINDOW TYP.

5A3

6A3

CLEAR PINE TRIM TYP.

TRIM BEYOND TYP.

WOOD TRIM (PINE) TYP.

WOOD PRICACY SCREEN BEYOND TYP.

RO

UP H

OPE

NIN

G

4' -

0"

EXISTING WALL BASE

4A3

179

7' - 4"

ROUGH OPENING

3' - 0"

ROUGH OPENING

3' - 0"

3' -

3"

RO

UG

H O

PEN

ING

4' -

0"

OPENING

OPENING

GLAZING GLAZING

RO

UG

H O

PEN

ING

4' -

6 3/

8"2'

- 8

5/8"

5' - 0"

CLEAR PINE TRIM TYP.

STATIONARY TEMPERED 1/4" CLEAR GLASS WINDOWSURROUNDED BY 3/4" CLEAR PINE WOOD FRAME

TYP.

0' -

2"0'

- 0

3/4"

1' - 6"

CLEAR PINE PRIVACY/ RECEPTION COUNTER TYP.

CLEAR PINE PRIVACY/ RECEPTION COUNTERBEYOND.

SOLID WOOD FRAMING ALL AROUND

RECESSED MECHANICAL FASTENER CONCEALED ATBASE TYP.

0' -

0 3/

4"0' - 1 1/2"

WOOD TRIM (PINE) TYP.

CLEAR PINE PRIVACY/ RECEPTION COUNTER TYP.

STATIONARY TEMPERED 1/4" CLEAR GLASS WINDOWSURROUNDED BY 3/4" CLEAR PINE FRAME TYP.

RECESSED MECHANICAL FASTENER CONCEALED AT BASE TYP.

0' -

0 3/

4"

0' -

0 3/

4"

0' - 1 1/2"

SOLID WOOD FRAMING ALL AROUND.




3 01/23/2015 FOR TENDER

DATE


T. 807 683 8005 F. 416 504 7712


SHEET NO.

DRAWN

PROJECT NO.

SHEET TITLE


CLIENT

PROJECT NAME


BrookMcIlroy/

1/22

/201

5 4:

41:2

2 PM

V:\2

012\

TB -

12-0

26-L

akeh

ead

Uni

vers

ity -

Arch

Ser

vice

s\12

-026

.13

- Hea

lth &

Cou

nsel

ling

Cen

tre (P

retti

e R

esid

ence

)\B -

Dw

gs +

Imag

es\B

2 D

raw

ings

\B2.

0 R

evit\

12-1

26.1

3 H

ealth

& C

ouns

ellin

g C

entre

(Pre

ttie

Res

iden

ce) -

Jan

14

2015

.rvt


Sections and Details

12-026.13

VLD

JANUARY 2015

A3


1/2" = 1'-0"1 Reception plan 1/2" = 1'-0"2 Elevation Reception Wall

3/4" = 1'-0"4 Section at Reception Opening

1/2" = 1'-0"3 Elevation 1 - a

1 1/2" = 1'-0"5 Reception Detail 1

1 1/2" = 1'-0"6 Reception Detail 2

NEW WOOD TRIM TO MATCH EXISTING TYP.

NEW SOLID WOOD SUPPORT MECHANICALLYFASTENED TO EXISTING COUNTERTOP AND NEWDESK EXTENSION WITH COUNTERSUNK WOODSCREWS AND ADHERED WITH WOOD GLUE TYP.

REMOVE EXISTING WOOD TRIM AND INSTALLNEW TRIM FOR STRENGTH TYP.

INSERT BISCUIT JOINT AT EVERY 6" O.C. TYP.APPLY WOOD GLUE TO EDGE OF EXISTINGCOUNTER TOP AND EDGE OF THE NEWEXTENSION.

NEW COUNTERTOP EXTENSION TO MATCH EXISTINGWOOD TRIM. CONTRACTOR TO VERIFY BESTSUITABLE SUPPORT LOCATION TYP..

EXISTING WOOD CABINET TYP.

WOOD SCREW 6" O.C. TYP.

2' - 9"

0' - 8"2' - 1" 0' - 0 3/4"

3' -

11 1

/2"

0' -

0 3/

4"

0' -

3 1/

2"


NEW SOLID WOOD SUPPORT MECHANICALLY FASTENEDTO EXISTING COUNTERTOP AND NEW DESK EXTENSION

WITH COUNTERSUNK WOOD SCREWS AND ADHEREDWITH WOOD GLUE TYP.

EXISTING WOOD TRIM TYP.

INSERT BISCUIT JOINT AT EVERY 6" O.C. TYP. APPLYWOOD GLUE TO EDGE OF EXISTING COUNTERTOP

AND EDGE OF THE NEW EXTENSION.

NEW COUNTERTOP EXTENSION TO MATCH EXISTINGWOOD TRIM. CONTRACTOR TO VERIFY BEST

SUITABLE SUPPORT LOCATION TYP.

2' - 1" 0' - 8"

0' - 0 3/4"

0' -

0"3'

- 10

3/4

"1' - 9"

0' -

3 1/

2"

EXISTING UPPER CABINET TYP.

WOOD SCREW TYP.


0' - 8"


NEW SOLID WOOD SUPPORT MECHANICALLY FASTENEDTO EXISTING COUNTERTOP AND NEW DESK EXTENSION

WITH COUNTERSUNK WOOD SCREWS AND ADHEREDWITH WOOD GLUE TYP.


INSERT BISCUIT JOINT AT EVERY 6" O.C. TYP. APPLYWOOD GLUE TO EDGE OF EXISTING COUNTERTOP

AND EDGE OF THE NEW EXTENSION.

NEW COUNTERTOP EXTENSION TO MATCH EXISTINGWOOD TRIM. CONTRACTOR TO VERIFY BEST

SUITABLE SUPPORT LOCATION TYP..

2' - 1"

3' -

10 3

/4"

1' - 9" 0' -

0 3/

4"

0' - 0 3/4" EXISTING WOOD CABINET TYP.

WOOD SCREW TYP.

0' -

3 1/

2"


NEW SOLID WOOD SUPPORT MECHANICALLYFASTENED TO EXISTING COUNTERTOP AND NEW

DESK EXTENSION WITH COUNTERSUNK WOODSCREWS AND ADHERED WITH WOOD GLUE TYP.


INSERT BISCUIT JOINT AT EVERY 6" O.C. TYP.APPLY WOOD GLUE TO EDGE OF EXISTING

COUNTER TOP AND EDGE OF THE NEWEXTENSION.

NEW COUNTERTOP EXTENSION TO MATCH EXISTINGWOOD TRIM. CONTRACTOR TO VERIFY BEST SUITABLE

SUPPORT LOCATION TYP..

EXISTING WOOD CABINET TYP.

WOOD SCREW 6" O.C. TYP.

2' - 1"0' - 8"0' - 0 3/4"

0' -

3 1/

2"

1' - 9"

0' - 0 3/4" 2' - 9"

3' -

11 1

/2"

1' - 6"

WOOD DESK EXTENSION TO MATCHEXISTING WOOD TRIM.

EXISTING PLYWOOD AND MELAMINECOUNTERTOP.

EXISTING UPPER CABINET.

NEW WOOD TRIM TO MATCH EXISTING.

INSERT BISCUIT JOINT AT EVERY 6" O.C.TYP. APPLY WOOD GLUE TO EDGE OFEXISTING COUNTER TOP AND EDGE OFTHE NEW EXTENSION.

2' - 1" 0' - 8" 0' - 0 3/4"

2' - 9 3/4"

NEW SOLID WOOD SUPPORTMECHANICALLY FASTENED TO EXISTINGCOUNTERTOP AND NEW DESK EXTENSIONWITH COUNTERSUNK WOOD SCREWSAND ADHERED WITH WOOD GLUE TYP.

6A4

0' - 8" 0' - 0 3/4"

0' -

0 1/

2"

EXISTING PLYWOOD AND MELAMINE COUNTERTOP.

NEW SOLID WOOD SUPPORT MECHANICALLYFASTENED TO EXISTING COUNTERTOP AND NEWDESK EXTENSION WITH COUNTERSUNK WOODSCREWS AND ADHERED WITH WOOD GLUE TYP.

INSERT BISCUIT JOINT AT EVERY 6" O.C. TYP. APPLY WOODGLUE TO EDGE OF EXISTING COUNTER TOP AND EDGE OF THENEW EXTENSION.

COUNTERSUNK WOOD SCREW AT 6" O.C. TYP.

RECESSED WOOD SCREW WITH WOOD PLUG SAND/FINISH TO MATCH TYP.

NEW COUNTERTOP EXTENSION TO MATCH EXISTING WOODTRIM. CONTRACTOR TO VERIFY BEST SUITABLE SUPPORTLOCATION TYP. REGISTER TOP OF EXTENSION WITH EXISTINGMELAMINE COUNTERTOP TYP.

RECESSED WOOD SCREW WITH WOOD FILLER SAND/FINISH TO MATCH TYP.




DATE


T. 807 683 8005 F. 416 504 7712


SHEET NO.

DRAWN

PROJECT NO.

SHEET TITLE


CLIENT

PROJECT NAME


BrookMcIlroy/

1/22

/201

5 9:

34:2

4 A

MV

:\201

2\TB

- 12

-026

-Lak

ehea

d U

nive

rsity

- A

rch

Ser

vice

s\12

-026

.13

- Hea

lth &

Cou

nsel

ling

Cen

tre (P

retti

e R

esid

ence

)\B -

Dw

gs +

Imag

es\B

2 D

raw

ings

\B2.

0 R

evit\

12-1

26.1

3 H

ealth

& C

ouns

ellin

g C

entre

(Pre

ttie

Res

iden

ce) -

Jan

14

2015

.rvt


Sections and Details

12-026.13

SMB

JANUARY 2015

A4

Health & Counselling CentreRenovation

1/2" = 1'-0"3 MED Room 151 Desk Extension

1/2" = 1'-0"2 Doctor's Office Room 150 Desk Alteration

1/2" = 1'-0"4 RN Office Room 143 Desk Alteration

1/2" = 1'-0"1 SR RN Room 162 Desk Alteration

1" = 1'-0"5 Section of Typical Countertop Extension 6" = 1'-0"6 Typical Countertop Extension Detail

3 01/23/2015 FOR TENDER

GENERAL PLUMBING NOTES:PARTIAL MAIN FLOOR PLAN - DOMESTIC WATER LAYOUT

PARTIAL MAIN FLOOR PLAN - SANITARY LAYOUT

PARTIAL SECOND FLOOR PLAN - SANITARY LAYOUTPARTIAL MAIN FLOOR PLAN - HVAC RENOVATION

NOTE:

DETAIL1M1

- FIRE DAMPER INSTALLATION

LAKEHEAD UNIVERSITY PRETTIE RESIDENCE - KEY PLAN

MECHANICAL SPECIFICATIONSGENERAL

PLUMBING

EQUIPMENT LIST

SCOPE OF WORK

SANITARY ISOMETRIC

ELECTRICAL LEGEND

PARTIAL MAIN FLOOR PLAN - RENOVATION

PARTIAL MAIN FLOOR PLAN - DEMOLITION

SINGLE LINE DIAGRAM - RENOVATION

“ ”

”

”

ELECTRICAL SPECIFICATIONS

WIRING METHODS

GROUNDING

LIGHTING

”

POWER AND CONTROL

DOOR HOLD OPEN DEVICE

VOICCE/DATA

PANIC ALARM

Date post:	08-Sep-2019
Category:	Documents
Upload:	others
View:	0 times
Download:	0 times

LAKEHEAD UNIVERSITY - ARCH SERVICES Lakehead Health... · mat'l material max maximum min minimum...

Documents