LATICRETE Masonry Veneer Installation System (MVIS) Catalog (8.5x11)

Product Selection Catalog

For additional product information snap the image with your phone. Get the free app for your phone at http://gettag.mobi

2 | www.laticrete.com/mvis

LATICRETE International, Inc. n One LATICRETE Park North, Bethany, CT 06524-3423 USA n Tel +1.203.393.0010 n Toll Free 1.800.243.4788 n Fax +1.203.393.1684 n www.laticrete.com

Innovative Tile and Stone Installation Systems

A Letter to SpecifierS:

re: LAticrete® Masonry Veneer installation System (MViS™)

LATICRETE has developed an enhanced system of Adhered Veneer Installation products to improve upon the traditional methods of installation that have demonstrated the tendency to fail through delamination and premature corrosion of the structural reinforcing.

The LATICRETE system is similar to the traditional method with the difference that instead of utilizing standard masonry cement mortars as in the past, polymer fortified adhesive mortar is used. LATICRETE Masonry Veneer Mortar has been specifically designed to provide high bond strength, flexibility and durability. It is used employing the same installation methods the installers have become accustomed to.

A further improvement is the inclusion of LATICRETE Hydro Ban™, a liquid applied breathable waterproof membrane that prevents moisture intrusion in barrier wall constructs. This membrane is located outside of the corrodible structural components of the wall offering maximum protection and longevity to the entire assembly.

In addition, the LATICRETE system allows for another option that increases quality and durability. Instead of a field formed lath and plaster substrate, which is subject to great variability in workmanship (and therefore quality), cement backer board is used. This substrate is typically used with tile and natural stone installations and is "time and field proven" to provide great consistency and durability in installations. By replacing the lath and plaster coat, this option also decreases the cost of the system at the same time as increasing performance levels.

LATAPOXY® Waterproof Flashing Mortar and LATICRETE Latasil™ silicone sealant allow for a complete installation that is protected by the LATICRETE System Warranty*.

Complete specifications and details are available at www.laticrete.com.

Thank you,

LATICRETE International, Inc.

* See Data Sheets 230.13, 230.15MVIS, and 025.0 for complete warranty information.

www.laticrete.com/mvis | 3

Table of Contents/Warranty Information

Consult our website at www.laticrete.com for the most current versions of product data sheets, warranties and MSDS sheets.

Content of this brochure is for informational purposes only. Refer to individual product data sheets and warranties for complete information.

^United States Patent No.: 6,784,229 B2 (and other Patents).†United States Patent No.: 6,881,768 (and other Patents).

Premium Latex Mortar BedLATICRETE 3701 Fortified Mortar Bed .............................................8

Pointing MortarLATICRETE Masonry Pointing Mortar ................................................8

SealantLATICRETE Latasil™ ........................................................................9LATICRETE Latasil 9118 Primer .......................................................9

Pointing Mortar and Sealant Color Chart ................................................9LATICRETE MVIS Details ............................................................................10 – 11

Warranty Information .................................................................................... 3

LATICRETE® Masonry Veneer Installation System (MVIS™) ................................. 4

WaterproofingLATICRETE Hydro Ban™ ..................................................................5LATAPOXY® Waterproof Flashing Mortar ..........................................5

Epoxy AdhesiveLATAPOXY 310 Stone Adhesive ......................................................6

Polymer Fortified Thin-Set MortarsLATICRETE 254 Platinum ...............................................................7LATICRETE Masonry Veneer Mortar..................................................7

PAgE PAgE

NOTES:* Available in markets outside of the United States of America and Canada.† Use of suitable flexible sealant is required per Tile Council of America Detail EJ171 for use in expansion joints, coves,

corners, changes in plane and other joints wherever tile or stone abuts dissimilar materials or restraining surfaces. ^ LATICRETE® Floor Warming Thermostat sold by LATICRETE International, Inc., warrants parts and materials for one (1) year

from the date of purchase. The sole remedy for the LATICRETE Floor Warming Thermostats is product replacement (see DS 230.13 for full details on the LATICRETE Product Warranty).

LATICRETE 25 Year System Warranty See Data Sheet 025.0 for complete warranty information.

APPLICATION PRODUCTS

Waterproofing/ Anti-Fracture

LATICRETE Hydro Ban™

LATAPOXY® Waterproof Flashing Mortar

Sound Control/ Anti-Fracture

LATICRETE 125 Sound & Crack Adhesive United States Invention Patent No.: 6,784,229 B2 (and other Patents).LATICRETE 170 Sound & Crack Isolation Mat* LATICRETE QT Sound Control Underlayment Patent No.: 6,920,723

Thick Bed Method LATICRETE 3701 Fortified Mortar Bed

Slurry Bond Coat LATICRETE 254 Platinum

Thin Bed Method LATICRETE 254 Platinum (regular or rapid version)

Spot Bonding LATAPOXY 310 Stone Adhesive -– Standard and Rapid Grade

Masonry Veneer Installation System

LATICRETE Masonry Veneer MortarLATICRETE Masonry Pointing Mortar

Sealant† LATICRETE Latasil™ LATICRETE Latasil 9118 Primer

LATICRETE 15 Year System Warranty MVIS™

See Data Sheet 230.15MVIS for complete warranty information.

APPLICATION PRODUCTS

Waterproofing LATICRETE Hydro BanLATAPOXY Waterproof Flashing Mortar

Scratch & Brown Plaster Coats

LATICRETE 3701 Fortified Mortar Bed

Thin Bed Method LATICRETE Masonry Veneer Mortar

Pointing / grouting LATICRETE Masonry Pointing Mortar

Sealant† LATICRETE LatasilLATICRETE Latasil 9118 Primer

LATICRETE offers a comprehensive 25 year, 100% labor and materials system warranty* for masonry veneer installations over concrete and masonry substrates (for both interior and exterior applications) and a 15 year, 100% labor and materials system warranty** for steel or wood framed exterior facades.

n LATICRETE Warranties Cover Any Suitable Tile or Stone Manufacturer’s Product, Allowing You to Select the Appropriate Product and Finish You Desire for Your Project

n Customizable Warranties Are Available to Suit Your Specific Project Requirements

* See Data Sheet 025.0 for complete warranty information.** See Data Sheet 230.15MVIS for complete warranty information.

Warranty Warranty

MVIS

Proudly Supports the

Masonry Veneer Manufacturers Association


ThE ChALLENgEThe explosive increase in popularity of adhered masonry veneer facades has created a need for higher performance, factory produced installation materials to assure consistently high quality installations.

Up to now, the installation of adhered masonry veneers has required the use of site-mixed Type S mortars – materials that are subject to large variations in consistency, quality and performance and which also limit the installation technique to that of traditional masonry.

Many projects have been plagued by delaminating stone and water intrusion among other installation issues inherent to materials and techniques which are limited in flexibility and margin for error. This traditional method is not engineered as part of a complete wall system and therefore does not offer warranties from a reliable source willing to stand behind the installation.

Many companies might say their products are low VOC, only one independently certifies it – LATICRETE.

n Third Party GREENGUARD Certification, Required to Meet Stringent Indoor Air Quality Standards

n Certified by GREENGUARD for Children & Schoolsn Helps Contribute Toward LEED Certificationn Product Certifications Readily Available at www.laticrete.com/green

ThE SOLUTIONRealizing these shortcomings, and based on our globally proven technology, LATICRETE has developed an installation system that provides a permanent, high strength installation that is freeze/thaw stable and protected from water intrusion.

Backed by the LATICRETE® 25 Year System Warranty*, the LATICRETE Masonry Veneer Installation System (MVIS™) allows for increased productivity utilizing either traditional masonry installation techniques or the “tile setter’s” method.

Vastly expanded architectural details are offered at www.laticrete.com/MVIS to help design professionals, contractors and installers understand the range of possible applications – and appropriate products and techniques which will assure long-term performance on projects of all types.


Warranty: LifetimeRefer to Data Sheet 663.0

LATICRETE® hydro Ban™

A single component self curing liquid rubber polymer that forms a thin, flexible, seamless, load-bearing and breathable waterproofing/crack isolation membrane. LATICRETE® Hydro Ban™ bonds directly to a wide variety of substrates and does not require the use of fabric in the field, coves or corners.

n Flood Test in 2 Hours*n Faster Flood Testing Over Fresh Mortar Beds and at Cooler Temperaturesn IAPMO and ICC Approved n Anti-Fracture Protection up to 1/8" (3 mm)n Easy to Clean With Water

PACkAgINgCommercial Unit: 5 gallon (19 l) pail liquid; 36 units per pallet.Mini Unit: 4 x 1 gallon (3.8 l) pails of liquid packed in a carton; 30 cartons per pallet.

APPROxIMATE COVERAgEPer Commercial Unit 250 ft2 (23.2 m2)

Per Mini Unit 50 ft2 (4.7 m2)

~ See Data Sheet 230.99 for complete warranty information.

* See Data Sheet 663.0 for complete product information. LATICRETE® Hydro Ban™ can be flood tested in 2 hours when cured at 70°F (21°C) or above 50% R.H. It can be flood tested in 24 hours when cured at 50 – 69°F (10 – 20.6°C) and up to 70% R.H. The time to flood testing starts when the second coat has completely cured from a light sage green to a darker olive green color.

Waterproofing

Warranty: 25 YearRefer to Data Sheet 070.0

LATAPOxY® Waterproof Flashing MortarLATAPOXY® Waterproof Flashing Mortar is an epoxy based 3 component, trowel applied, waterproofing and vapor barrier membrane. It can be used to waterproof seams, gaps or joints between a variety of substrates and metal and PVC pipe penetrations or flashing. It is specifically designed to be used under ceramic tile, stone or brick for rapid installations which require a fast curing waterproof flashing. LATAPOXY Waterproof Flashing Mortar is flexible, easy to apply and will allow for rapid installations.

n Easy to Apply Using a Troweln Adheres to Metal and PVC Pipes, Drains and Flashingn Waterproof Seam Between Flashing and Facade

PACkAgINg3.5 gallon pail with 2 LATAPOXY Waterproof Flashing Mortar Part A 1.4 lbs (.65 kg), 2 LATAPOXY Waterproof Flashing Mortar Part B

1.15 lbs (.5 kg), and 2 LATAPOXY Waterproof Flashing Mortar Part C 5.5 lbs (2.5 kg)

48 units per pallet.

APPROxIMATE COVERAgE

45 ft2/unit (4.2 m2) at 1/8" (3 mm) thick, depending on application


Community College of Southern Nevada, Las Vegas, NV

Epoxy Adhesive

LATAPOxY® 310 Stone AdhesiveA two-component, high strength construction epoxy adhesive for spot bonding large format tile and stone on vertical surfaces, for interior or approved exterior applications. Offers major advantages in terms of speed and productivity over mechanical anchoring, plaster and wire, and the thin-set method of veneer installation. Comes in both standard and rapid version for faster curing. Easier to work with when compared to traditional methods – no drilling, cutting of kerfs or setting of pins – LATAPOXY® 310 Stone Adhesive allows for quick, easy plumb adjustment while stone is in place to compensate for uneven walls and stone thickness variations. LATAPOXY 310 Stone Adhesive is permanent; it will not fail or deteriorate over time and is ICC and IBC approved.

PACkAgINgkit: 2.6 gallon (10 l): All components packed in one carton; 40 cartons per pallet. Available in standard and rapid versions.2 gallon (8 l): 1.06 quart (8 x l) units packed in one carton; 40 cartons per pallet. Available in standard and rapid versions.

APPROxIMATE COVERAgE

AVERAgE INChES (OR MILLIMETERS) OUT OF PLUMB

LATAPOxY® 310 STONE ADhESIVE ThICkNESS

APPROxIMATE COVERAgE/10 LITER UNITS

Plumb Wall (3 mm) 1/8" Thick (3 mm) 300 – 325 ft2 (27 – 30 m2)

1/4" (6 mm) 1/4" Thick (6 mm) 150 – 170 ft2 (14 – 16 m2)

1/2" (12 mm) 1/2" Thick (12 mm) 75 – 80 ft2 (7 – 7.5 m2)

Warranty: 25 YearRefer to Data Sheets 679.0 and 679.3


Polymer Fortified Thin-Set Mortars


LATICRETE Masonry Veneer MortarLATICRETE Masonry Veneer Mortar is a patented, versatile polymer fortified mortar designed specifically for the installation of stone, thin brick and manufactured stone masonry veneers. A high performance mix provides maximum non-sag performance for vertical installations and also obtains maximum bond strength to the substrate and selected veneers. Reinforced with Kevlar®^ for added strength, LATICRETE Masonry Veneer Mortar offers exceptional workability.

PACkAgINg40 lb (18.2 kg) bag; 56 bags per pallet; Grey.

APPROxIMATE COVERAgE Per 40 lb (18 kg) bag

VERTICAL APPLICATIONS ft2 m2

1/4" x 3/8" (6 mm x 9 mm) notched trowel 48 – 58 4.4 – 5.4

1/2" x 1/2" (12 mm x 12 mm) notched trowel 36 – 44 3.3 – 4.1

Adhered Manufactured Stone Masonry Veneer 28 – 35 2.6 – 3.2

^ United States Patent No..: 6784229 B2 (and other patents).


LATICRETE® 254 PlatinumThe ultimate one-step, polymer-fortified thin-set that provides unsurpassed strength, far exceeding all ANSI A118.4 and ANSI A118.11 strength requirements. Ideal for interior, exterior, and submerged applications on virtually all substrates and applications. Increases your productivity with long open time, allowing flexibility on the job site that results in fast, accurate installations. Easy to trowel mortar assures proper coverage on both the substrate and the veneer as well as less fatigue for the installer. The exceptional bond strength and easy workability of LATICRETE® 254 Platinum makes this multipurpose the ultimate adhesive for difficult to bond porcelain tiles as well as glass mosaics and large format glass. Inhibits the growth of stain-causing mold and mildew in substrates with Microban® antimicrobial protection.

PACkAgINg50 lb (22.7 kg) bag; 56 bags per pallet; Grey and White.

APPROxIMATE COVERAgE Per 50 lb (22.7 kg) bag

NOTCh TROWEL COVERAgE1/4" x 1/4" (6 mm x 6 mm) 80 – 95 ft2 (7.4 – 8.8 m2)1/4" x 3/8" (6 mm x 9 mm) 60 – 70 ft2 (5.6 – 6.5 m2)

1/2" x 1/2" (12 mm x 12 mm) 40 – 45 ft2 (3.7 – 4.2 m2)


Premium Latex Mortar Bed/Pointing Mortar

LATICRETE® 3701 Fortified Mortar BedLATICRETE® 3701 Fortified Mortar Bed is a one-step polymer fortified blend of carefully selected raw materials, portland cement and graded aggregates. LATICRETE 3701 Fortified Mortar Bed does not require the use of latex admix; you only need to add water to produce a thick bed mortar or render with exceptional strength. Save time and money by eliminating the need for job site measuring and mixing of sand and cement to the proper ratio. A suitable alternative to LATICRETE 3701 Mortar Admix combined with LATICRETE 226 Thick Bed.

PACkAgINg60 lb (27.3 kg) bag; 56 bags per pallet.

APPROxIMATE COVERAgE12 ft2 at 1/2" (1.1 m2 at 12 mm)

6 ft2 at 1" thickness (0.56 m2 at 25 mm)3 ft2 at 2" (0.3 m2 at 50 mm)


LATICRETE Masonry Pointing MortarA premium, factory prepared Masonry Pointing Mortar for use with natural or manufactured stone. Designed to be mixed with water or LATICRETE 1776 Grout Enhancer. Formulated from a blend of high strength portland cement, graded aggregates, and color-fast pigments. Provides a joint that is dense, hard and durable.

COLORSSee Grout and Sealant Color Chart on page 9 for a list of available colors.

PACkAgINg50 lb (22.7 kg) bag; 56 bags per pallet.



Sealants/Pointing Mortar and Sealant Color Chart

88 Silver Shadows

89 Smoke greys

50 Sea glasss

44 Bright Whites X

39 Mushrooms

85 Almonds X

46 Quarry RedX

35 Mochas

67 Autumn greens

61 Parchments X

66 Chestnut Browns

30 Sand Beiges

78 Sterling Silvers

52 Toasted Almonds

24 Natural greys X

23 Antique Whites

40 Lattes X

17 Marble Beiges

42 Platinum s

22 Midnight Blacks

This chart shows available colors for the following: X LATICRETE® Masonry Pointing Mortar s LATICRETE Latasil™

POINTINg MORTAR AND SEALANT COLOR gUIDELINESPointing Mortar and sealant samples are guides only. LATICRETE does not warrant color matching to this color chart or to any color guide produced. Actual shade and texture will depend on job site conditions, lighting, installation techniques and types of tile or stone used, and may vary from this color chart, color channel kits and color swatch on product packaging. Verify actual appearance and compatibility with a test area before installing. Blend pointing mortar with different control numbers. Follow ANSI A108.10/MMSA Bulletin #9 grouting practices. No claims for color shade variations will be honored.

Note: Pointing mortar color availability is subject to change. Visit www.laticrete.com for most current color selections.† United States Patent No.: 6881768 (and other Patents).^ United States Patent No.: 6,784,229 B2 (and other Patents).

LATICRETE Latasil™

High performance, 100% silicone sealant designed for use in coves, corners, changes in plane and expansion joints in exterior and interior applications of tile and stone. Can be used in swimming pools and other wet area applications. LATICRETE Latasil™ conforms to ASTM C-920 and ASTM C-794 adhesion properties and inhibits the growth of stain-causing mold and mildew in sealant joints with Microban® antimicrobial product protection.

COLORSSee Grout and Sealant Color Chart on right for a list of available colors.

PACkAgINg10.3 oz (305 ml) cartridges; 6 cartridges per carton; 240 cartons per pallet.

APPROxIMATE COVERAgE Per cartridge

ThICkNESS COVERAgE

1/4" x 1/4" (6 mm x 6 mm) 25 linear feet (7.62 m)

3/8" x 3/8" (9 mm x 9 mm) 11 linear feet (3.35 m)

LATICRETE Latasil™ 9118 PrimerIncreases adhesion for porous stone, underwater, and permanent wet area applications.

PACkAgINg8 oz (240 ml) bottle; 5 bottles per carton; 50 cartons per pallet.

APPROxIMATE COVERAgE Per cartridge

ThICkNESS COVERAgE

1/4" x 1/4" (6 mm x 6 mm) 350 linear feet (106 m)

3/8" x 3/8" (9 mm x 9 mm) 175 linear feet (53 m)

Warranty: LifetimeRefer to Data Sheets 6200.1

Refer to Data Sheet 6528.1


LATICRETE® MVIS™ Details

A Adhered Masonry Veneer

B LATICRETE® Masonry Pointing Mortar

C LATICRETE Masonry Veneer Mortar

D LATICRETE Hydro Ban™ (for warranty qualification some applications require waterproofing)

E LATICRETE 3701 Fortified Mortar Bed

DETAIL LEgEND

NOTE: 1. Substrates scheduled to receive manufactured stone, natural stone and thin brick must be structurally sound, rigid and conform to good design/engineering practices in accord with all applicable building codes with maximum deflection under all live, dead and impact loads, including concentrated and all anticipated loads of L/360

for thin brick and ceramic tile and L/480 for manufactured and natural stone. Steel and wood frame constructs shall also be designed to meet this criteria. Lateral bracing and edge support for cement backer board panels is required.

2. LATICRETE® Masonry Pointing Mortar is designed to meet product applicable project specifications. LATICRETE

Masonry Pointing Mortar does not inhibit efflorescence from occurring in natural or manufactured stone facade installations. Efflorescence is a normal condition that may occur when installing portland cement based products. During installation, strike joints in a consistent time frame relevant to application time. Pointing mortar should be

thumbprint dry before striking. Striking joints too early or too late can create color inconsistencies.

3. Masonry Pointing Mortar color samples are guides only. LATICRETE does not warrant color matching to any color guide produced. Actual shade and texture will depend on job site conditions, lighting, installation techniques,

W202-EConcrete – Direct Bond, Thin Bed Method With

Waterproofing – Exterior Wall

W244-IWood Framing or Cement Backer Unit/Steel –

Interior Wall

W221(E)Concrete or Masonry – Cement Leveling Bed With Wire Lath and


CD

B ACh

B A

CDEFg

B A


LATICRETE MVIS Details

and types of tile or stone used. Verify actual appearance and compatibility with a test area before installing. Blend colored mortars with different control numbers. Follow ANSI A108.10/MMSA Bulletin #9. No claims for color shade variations will be honored.

4. Please consult LATICRETE Technical Services for more information. 1.800.243.4788, ext. 235, www.laticrete.com, [email protected].

5. For information on pumpable scratch and brown coats, contact LATICRETE Technical Services.

6. For complete application information and limitations consult related Product Data Sheets and Execution Statements related to these details and applicable standards. See warranty Data Sheet 025.0 for full information and terms.

7. As a professional courtesy, LATICRETE offers technical services free of charge. The user maintains all responsibility for verifying the applicability and suitability of the technical service or information provided.

F Metal Lath, 3.4# Galvanized Diamond Wire Lath

g Cleavage Membrane 15 lb Builders Felt or 4 mil Polyethylene

h Cement Backer Board

I Exterior Rated Sheathing

W244-EWood Framing or Cement Backer Unit/Steel –

Exterior Wall

W265Steel Framing with Exterior Rated Sheathing – Cement Leveling Bed with Wire Lath and


W300Concrete or Concrete Masonry Unit (CMU) – Cement Leveling Bed With

Waterproofing – Exterior or Interior Wall

CD

Eg

FI

B A

Ch D

I

g

B A

CDE

B A

©2010 LATICRETE International, Inc.LATICRETE, LATAPOXY, SPECTRALOCK and the logo are Registered Trademarks of LATICRETE International, Inc.

Corporate Headquarters:LATICRETE International, Inc.

One LATICRETE Park NorthBethany, CT 06524-3423 USA1.800.243.4788+1.203.393.0010

www.laticrete.com

Asia Pacific: +852.2526.6660

Australia: +61.3.9933.6111

China: +86.21.5789.3300

Eastern Europe: +790.9661.1644

Europe: +34.96.649.1908

India: +91.40.3041.3100

Latin America: +1.203.393.0010

Middle East: +971.7.244.6396

South East Asia: +65.6515.3028

DS-005.2-0810

Microsoft, MSN, and Windows Vista are trademarks of the Microsoft group of companies.Microban is a registered trademark of Microban Products Company.Kevlar is a registered trademark of Dupont Products Company.GREENGUARD Indoor Air Quality Certified is a Registered Trademark of the GREENGUARD Environmental Institute.

Disponible en français. Visiter www.laticrete.com/fr pour les informations complètes.

Disponible en español. Visite www.laticrete.com/sp para la información completa.

Date post:	10-Apr-2015
Category:	Documents
Upload:	laticrete-international
View:	557 times
Download:	1 times

LATICRETE Masonry Veneer Installation System (MVIS) Catalog (8.5x11)

Documents