LAUDIO PLYTECHNICAL VENEER PLYWOODFOR INDUSTRIAL APPLICATIONS
Technical veneer plywood for construction, industrial bodywork, packaging and other uses. Manufactured using unrolled sheets of European Radiata Pine (thickness 2.1 to 3.2 mm) glued with phenolic resin, water-resistant (WBP), pressed, hot-polymerised and pressurised.
10
7
10
10
S-P-00531environdec.com
HIGH RESISTANCE
CERTIFIED
PROFITABILITY
ANTI-HUMIDITY
LAUDIO PLYPRODUCT SPECIFICATIONSEuropean Radiata Pine veneer plywood with uncovered sides, calibrated and sanded.
PRODUCT CERTIFICATESThe product is guaranteed by current standard-compliant certificates in terms of quality and structure. Sustainable environment-friendly product.
USES AND APPLICATIONSWooden constructions: roofs, ceilings, floors, parquet flooring, walls and covering. Platforms, walls and ceilings in industrial vehicle and caravan structures, lamina-ted panels, sandwich boards and cladding. Special and high-resistance packa-ging. Protection and separations at work sites.
FINISHESPly II: Veneer plywood, sanded, with knots repaired on both sides.Ply II/III: Calibrated, sanded plywood with knots repaired on one side.Ply III: Calibrated, sanded plywood with no knots repaired on either side.Ply IV: Uncalibrated, unsanded plywood with no knots repaired on either side.
(*) Maderas de Llodio S.A. manufactures boards of other sizes to order. Please contact our commercial technicians.
Gluing quality: Class III exterior according to UNE EN 314-2
Intended use: for internal use as a structural component in dry conditions, EN 636-1 S / for protected external use as a structural component in humid conditions, EN 636-2 S
Formaldehyde emission: E1 according to UNE 717-2
Recommendations on handling, use and storage: see guide to good practice at www.maderasdellodio.com
Values or properties not shown on this sheet must be checked with technicians at Maderas de Llodio, S.A.
Maderas de Llodio reserves the right to modify the design of its products
+-0,5 mm (on one panel)
PHYSICAL AND MECHANICAL SPECIFICATIONS OF STANDARD PRODUCTS
DIMENSIONS (m)
DENSITY (+-5%)
THICKNESS (mm)
GRAIN DIRECTION FLEXURAL
STRENGTH (N/mm2)
MODULUS OF ELASTICITY IN BENDING (N/mm2)
TYPICAL VALUES FOR FLEXURAL STRENGTH AND AVERAGE VALUES FOR MODULUS OF ELASTICITY ACCORDING TO UNE EN 789-1058 STANDARD
DIMENSIONAL TOL.According to UNE EN315
UNE EN 315 THICKNESSTOLERANCE RANGE (mm)
MADERAS DE LLODIOTHICKNESS TOLERANCE
TOL. FOR PLY IV BY MADERAS DE LLODIO
26,8 11,7
8.819 3.444
9
THE VALUES GIVEN IN THIS TABLE CORRESPOND TO PRELIMINARY PREPARATION OF THE BOARD AT 12% HUMIDITY
22,2 10,1
7.881 2.316
12
22,9 11,8
7.827 3.609
15
22,6 18,9
8.331 5.885
18
17,7 13,9
6.110 4.414
21
20,0 18,2
6.699 5.204
24
19,8 17,1
6.504 5.050
30
8,32÷9,47 11,24÷12,56 14,15÷15,65 17,06÷18,74 19,97÷21,83 22,88÷24,92 28,7÷31,1
+-0,2 mm (on one panel)
2,44 X 1,22 / 2,50 X 1,25 / 2,50 X 1,53 / 3,00 X 1,50 (*)
550 Kg/m3
THINK BEFORE PRINTING
Polígono Ind. Santa Cruz s/n, 01400 Llodio (Álava) SpainPhone: +34 94 672 01 00 Fax: +34 94 672 05 [email protected]
MADERAS DE LLODIO S.A.S-P-00531environdec.com
S-P-00531environdec.com
LENGTH-WIDTH: UP TO +-3,5 mm
SQUARE: 1mm/m
