Part No. 1KA6P2P0024-- N4HME APRIL 2007 Reference No. SM1110008-00 LCD Monitor Service Manual Give complete "SERVICE REF. NO." for parts order or servicing, it is shown on the rating sheet on the cabinet back of the TV set. Note This TV receiver will not work properly in foreign countries where the television transmission system and power source differ from the design specifications. Refer to the specifications for the design specifications Contents Safety precautions/Specifications ..................................................................................................................2 Service Mode/Service Data ........................................................................................................................3~7 HDMI / PC / Component Signal Support Timing List ......................................................................................8 Cabinet Disassembly ................................................................................................................................9~11 Block Diagram ..............................................................................................................................................12 Power Diagram ............................................................................................................................................13 Power and Control Diagram ........................................................................................................................14 RS232 Settings ......................................................................................................................................15~16 Troubleshooting ............................................................................................................................................17 IC Descriptions........................................................................................................................................18~19 IC Block Diagrams ........................................................................................................................................................................ 20~26 Cabinet Parts List ........................................................................................................................................27 Pin description of semiconductors ................................................................................................................28 Electric Parts List ..........................................................................................................................................29 Model CE32LM4WPR-E Service Ref. No. CE32LM4WPR-E-00 PRODUCT CODE: 113005911 ORIGINAL VERSION: Chassis No.UK4-B Please use Schematic Diagram 1KA6P2P0025-- inserted with this Service Manual. CE32LM4WPR-E FILE NO.
Transcript
Part No. 1KA6P2P0024-- N4HME APRIL 2007 Reference No. SM1110008-00
LCD MonitorService Manual
Give complete "SERVICE REF. NO." for partsorder or servicing, it is shown on the rating sheeton the cabinet back of the TV set.
NoteThis TV receiver will not work properly in foreigncountries where the television transmission system and power source differ from the designspecifications. Refer to the specifications for thedesign specifications
ContentsSafety precautions/Specifications ..................................................................................................................2Service Mode/Service Data ........................................................................................................................3~7HDMI / PC / Component Signal Support Timing List......................................................................................8Cabinet Disassembly ................................................................................................................................9~11Block Diagram ..............................................................................................................................................12Power Diagram ............................................................................................................................................13Power and Control Diagram ........................................................................................................................14RS232 Settings ......................................................................................................................................15~16Troubleshooting ............................................................................................................................................17IC Descriptions........................................................................................................................................18~19IC Block Diagrams........................................................................................................................................................................20~26Cabinet Parts List ........................................................................................................................................27Pin description of semiconductors ................................................................................................................28Electric Parts List ..........................................................................................................................................29
Model CE32LM4WPR-E
Service Ref. No. CE32LM4WPR-E-00
PRODUCT CODE: 113005911
ORIGINAL VERSION: Chassis No.UK4-B
Please use Schematic Diagram 1KA6P2P0025--inserted with this Service Manual.
CE32LM4WPR-E
FILE NO.
-2-N4HME
SAFETY PRECAUTION
PRODUCT SAFETY NOTICE
SPECIFICATIONS
Product safety should be considered when a component replacement is made in any area of a receiver. Componentsindicated by mark in the parts list and the schematic diagram designate components in which safety can be of special significance. It is particularly recommended that only parts designated on the parts list in this manual be usedfor component replacement designated by mark . No deviations from resistance wattage or voltage ratings may bemade for replacement items designated by mark .!
!
!
1: An isolation transformer should be connected in thepower line between the receiver and the AC line when aservice is performed on the primary of the convertertransformer of the set.
2: Comply with all caution and safety-related notesprovided on the cabinet back, inside the cabinet, on the chassis or the picture tube.
3: When replacing a chassis in the cabinet, always be cer-tain that all the protective devices are installed properly,such as, control knobs, adjustment covers or shields,barriers, isolation resistor-capacitor networks etc. Beforereturning any television to the customer, the service tech-nician must be sure that it is completely safe to operatewithout danger of electrical shock.
Power source AC 220~240V, 50HzTelevision system System I B/G, D/K, L/L’Colour system PAL/NTSC4.43 (PAL/NTSC4.43/NTSC3.58 IN AV MODE), SECAMReceiving channel UHF: 21~69
VHF: E2-E12, F2-F10, R1-R12CATV: X, Y, S1-S41, B-Q
Aerial input impedance 75ohmAV terminal
AV1: CENELEC standardINPUT: Composite video, RGB and Audio L/R
OUTPUT: TV-output with composite video and audio L/R AV2: BNC
INPUT: RGB, H and V / Y, Pb, Pr and audio L/ROUTPUT: RGB, H and V / Y, Pb, Pr
AV3: BNCINPUT: Composite video
OUTPUT: Composite videoAudio M.Out Cinch: L/RHDMI
INPUT: HDMI GROUP StandardPC INPUT:Serial Port RS232C
INPUT/OUTPUT:Contrast Ratio 1000:1Display Resolution 1366 x 768 (WXGA)Viewing Angles H: 176°, V: 176°Dimensions (WxHxD) 803 x 493 x 162 Weight 21.8 Kg
Important recycling information.
Your SANYO product is designed andmanufactured with high quality materialsand components which can be recycledand reused.
This symbol means that electrical andelectronic equipment, at their end-of-life,should be disposed of seprately.
In the European Union there are separate collection systems forused electrical and electronic products.
Please help us to conserve the environment we live in!
Note: This symbol mark and recycle system are applied only to EU countries and are not applied to other countries of the world.
RoHS.This product does not contain any hazardous substances prohibited by the RoHS Directive.(You will find “R” or “Z” at the last digit of the serial number or an “RSF” label near the rating plate on the RoHS compliant product.)
WARNING.You are requested to use RoHS compliant parts for maintenance or repair..You are requested to use lead-free solder .
!
!
�
-3-N4HME
HOTEL MODETo enter Hotel Mode press and hold the green button on the remote control for 3 seconds.Hotel Mode allows the user to set up the function of the set
SERVICE MODETo enter Service Mode press and hold the green button on the remote control whilst pressing the 6 button on the tv cabinet at the same time,alternatively:-From Hotel Mode press and hold the green button on the remote control for 3 seconds
To select the service item and change data value
+ To select the adjustment item, use the 5 or 6 buttons.+ To change the service data, use the Volume - (LEFT) or Volume + (RIGHT) buttons.+ The data which is set in the service mode is stored into the memory IC automatically
EXAMPLE: 000 UK4B 07.45
ITEM NO SECTION VALUEITEM
EXIT FROM THE SERVICE MODE+ Press the MENU button or turn off the TV set by using the Mains switch.
-4-N4HME
CE32LM4WPR-E
14485
At FM mode, count the NICAM error, if less than this data, set to NICAM
At NICAM mode, count the NICAM error, if more than this data, set to FM
EU/ASIA
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
70
69
68
67
66
65
64
63
62
61
15500
0
40
10
224
15
12
10
6
224
15
10
8
3
224
15
8
7
1
224
15
8
6
0
0
0
0
0
0
8
1
0
45
2450
460
31
0
0
23
27
25
22
31
27
36
21
38
44
38
32
31
127
16
1
1
1
133
2
1
50
14
0
0
0
0
0
60
0.00.00
15.00.02
MF6.22UK4B
Init TV
ISP Mode
Scaler version
SubMic version
Power/Hour
Error
DCXO
DCXO Auto
Nicam Low Er Limit
Nicam Up Err Limit
Auto Zoom 4:3
Azoom 4:3 def
Azoom 16:9 def
WSS
Gid-SCART
Software version
For initialise the TV, all tuning data is elased
Bus line stops. For control by PC
Scaler soft version --- 15.00.02 is example
Sub micon software version --- 0.00.00 is example
Working hours since first ON
Bus Error countert
DCXO alignment
DCXO AUTO
Zoom setting
Zoom setting
Zoom setting
WSS 0:NO 1:Yes Depend on the signal, change 16:9 / 4:3
Grid scart
black bar detecting Stitch --- Not using
RGB data
PC Colour offset
PC tint offset
Dynamic Brightness data
Dynamic Colour data
Standard Contrast data
Dynamic Contrast data
Dynamic Sharpness data
Standard Brightness data
Standard Colour data
Standard Sharpness data
Eco Brightness data
Eco Contrast data
Eco Contrast data
CRT RGB output SW, CRT-1
Composit colour, delay of UV to Y
CVBS colour, delay of Y to C
Noise reduction AUTO: set the limit of high
Noise reduction AUTO: set the limit of low
Noise reduction MAX setting
Noise reduction MAX setting
Noise reduction MAX setting
Noise reduction MAX setting
Noise reduction MAX setting
Noise reduction MID setting
Noise reduction MID setting
Noise reduction MID setting
Noise reduction MID setting
Noise reduction MID setting
Noise reduction MIN setting
Noise reduction MIN setting
Noise reduction MIN setting
Noise reduction MIN setting
Noise reduction MIN setting
Noise reduction off setting
Noise reduction off setting
Noise reduction off setting
Noise reduction off setting
Noise reduction off setting
SOC vsp
Forced Slicing Level fixing SW
Forced Colour-On, at poor signal condition intentionally Colour ON
Mechanical Disassemblies (CE32LM4WPR-E)1. Check points before disassembly
Check the location of tamper proof marking (Fig-1)If the marks are removed or touched, somebody may have already disassembled the set.This makes the warranty regarding this IP model invalid.
After finishing the service, make the set tamper proof again with silver paint.
2. Rear Plate Removal
Remove screws A (6 pcs), then remove the Terminal Cover (Fig-2)
Remove screws B (4 pcs), then remove the AV Terminal (Fig-3)Remove screws D (12 pcs) - (Fig-6)Remove screw C (Fig-5), then remove the Rear Plate.Remove antenna lead either at Rear AV or PCB connector.
-10-N4HME
Mechanical disassemblies cont.
-11-N4HME
Location of Circuit Board and Electric Parts
3. Chassis and Fan Removal
Screw A : M3 x 6
PWB, POWER
PWB, SUB AV
Note: Control Board is fixed on Cabinet Front.
A A
Mechanical disassemblies cont.
-12-N4HME
BLOCK DIAGRAM
This is a diagram for all models and therefore differs slightly from the actual block diagram.
LCD PANELS
CA
LER
Digital Interface ADC
D-RGB
TEXT/OSD MIX
YC
IF
VIDEO SWITCH
RGB/YPBPR
VIFIN1 LOC2
PANELLVDS
VIF
TUNER
GTV
SCART1
CVBS1
TV OUT (CVBS)
RGB1
CVBS3
RGBSWITCH
VIDEOSWITCH
BA7652
SVO6/CVBS6CVBS
CVBS_Y4
CVBS_Y5
SWO1_CVBS20_Y20
CVBS30_Y30
DVBO_IFVO_FMRO
HDMI
TMDS
BA7603
SiI9021
HDMIDECODER
D-RGB
RGB
CV
BS
PV
10_23
IN_R
IN_G
IN_B
R3_PR31G3_Y31
B3_PB31
PC
RGBRGB
SWITCH
BA7657
MATRIX
COMPONENT
YPBPR RGB
H/V
Y/G
Pb/B
H/V
Pr/R
H
V
OUT IN
OUT
IN
Outline
-13-N4HME
1 2 3 4 5 6
KQ
1
1
PO
WE
R 1
ON
/OF
F
IC66
046V
PO
WE
R 4
PA
NE
L O
N
ON
/OF
FIC
6613
IC66
00
IC66
01
5V3V3
ST
B
5V S
TB
24V
IC66
10
IC66
09
IC66
08
IC66
07
IC66
06
IC66
05
IC66
03
IC66
02
13V
_PW
R
9V 12V
_FA
N
5V_S
W
3V3_
SW
D5V
D3V
3
1V8_
SW
D1V
8
PO
WE
R
AR
CH
ITE
CT
UR
E
D66
01
D66
21
D66
18
D66
16
D66
07
D66
06
D66
05
D66
04
D66
15
D66
14
TO
IC80
1P
IN E
10
5V
1 2 3 4 5KQ
24V
6V
D3V
3
D5V
3V3_
SW
5V_S
W
12V
_FA
N
9V
PR
OT
EC
T
AR
CH
ITE
CT
UR
E
2 3 4 5 KR
PO
WE
R
TO
UN
IT
PO
WE
R D
IAG
RA
M F
OR
UK
4B
-14-N4HME
Power and Control Diagram
PJ-NET
POWER CONNECTOR MAIN
SUB-AV-BNC
SUB-AV SOCKET
1KA9W0640017-
K2009
TX
RX
5V
5V
3.3V
12V
3.3V
5V cct
K2014
K2013
K2006
KCPA
TO G19
KCP
IC1551
1AA93ABAF300X
KG 1 2 3 4
P_FAIL
5V1A
KA
KQ
16V Main Supply
1
8
1
5
12V
5V
3.3V
K3000
cct
K3A 12V
K3003 K603
K303-03
K3Q
K3R KR
5V S/B
K605 K3002
K605-02 5V
gnd
16V
12V
Gnd
Gnd
Gnd
Gnd
NC
NC
NC
NC 1
2
3
4
5
6
7
8
9
10
11
12
13
14
1
2
3
4
5
6
7
8
9
10
11
12
1
2
3
4
5
6
7
8
9
10
11
12
1
2
3
4
5
6
7
8
9
10
11
12
13
14 5V S/By
Gnd
D5V
Power on
ON/OFF
VBR
NC
NC
NC
NC
Gnd
Gnd
K3001
NC
NC
NC
NC
NC
1
11
1
6
POWER_3
BL_ADJ
BL_ON
3.3V S/B
KP R1600
R1601
gnd
1AA0B10H086JA
1AA0B10H087D01AA0B10H086JB1AA0B10H086G0
-15-N4HME
The TV control commands are used to control a TV through RS232C from a computer.Serial Interface SpecificationTransfer Specification1. Transmission Speed : initial setting value is 192002. Transmission speed can be changed by service mode (hotel mode)
ConnectionThe designated RS232C serial cable that is provided with the LCD monitor must be used for a connection between a computer and a LCD monitor
The TV command is defined by one command / one line that starts with “C” and ends with carriage return (0x0D)There are two types of commands:1. Functional Execution Commands e.g. Co5[CR] (see table on following page)2. Status Read Commands e.g. “CR0 [CR] (see table on following page)
Setting the monitor address in RS232 modeTo access hotel mode press the green button on the remote control and hold for 5 seconds. The following screen will appear
Each monitor can have a specific address e.g. 007 which helps command that monitor individually and will not affect other monitors connected toa controlling pc.
Address format commandThe adressing format command is used for operating multiple monitor sets from a single pc via the RS232 command line. If you set your monitoraddress to ‘000’ it will never respond to any addressing command from the pc. If the address from the pc is ‘FFF’, all monitor sets will execute thecommand. The address format command is defined by one command, one line which starts with ‘A’ and ends with carriage return (0x0D). An address isadded at the top of a control command.Example:Functional execution command: “A001C05” [CR] means the address is 001 and the control command is C05Status read command: “A001CR0” [CR] means the address is 001 and the command is CR0
The monitor can set its own address in the hotel option (see above). The address range is 000 - 999, the default address will be 000.The baud rate indicates the unit transfer speed of data from the pc the the monitor sets.
RS232C SETTINGS
ITEM SPECIFICATION
Synchronous system AsynchronousTransmission Speed 9600 / 19200Data Length 8 bitParity NoneStop BitFlow Control None
1
123456789
123456789
(D-Sub 9 Pin) (D-Sub 9 Pin)
CD
RXD
TXDDTR
SG
DSR
RTS
CTS
RING
N.C.
RXDTXD
N.C
SG
N.C
RTS
CTS
N.C.
MENU
Hotel mode ON / OFFOn program OFF/ 1~99Preset ON / OFFAddress 007Baud Rate 19200
/ AV1-AV3 /RGB/ HDMI/ PC
Hotel
: Select : Adjust : Exit
-16-N4HME
Functional Execution Command Table
Command Item Comment
Toggle (Dynamic, Standard, Eco, Personal)
“---”_means “No Function”
CF DEA RMCN
CF DEA RMCY
CF CLOK OFF
CF CLOK ON
CF DPMS OFF
CF DPMS ON
C92C64
C76
C75
C74
C73C72
C71
C70C30
C0F
C29
C28
C27
C26C25
C24C23
C01
C00
Picture
AV1 direct
Wide “Normal” direct
Wide “Full” direct
POWER ONPOWER OFFWide “Auto” direct
Wide “Natural” direct
Wide “Zoom 16:9” direct
Wide “Title in 16:9” directWide “Zoom 14:9” direct
Wide “Title in 14:9” direct
RGB direct
AV2 RGBHV direct
AV2 YPbPr direct
AV3 direct
HDMI direct
PC direct
PC Auto adjustFactory settings
Power save ONPower save OFF
Child lock ON
Child lock OFF
RC inhibition OFF
RC inhibition ON
Status Read Command TableCommand Item Note
“---”_means “No Function”
C** Panel operating time
CR0
CR1
CR WIDE
CR PICTURE
CR SIGNAL
CR CHILD
CR DPMS
Power
Input mode
Wide mode
Picture mode
Signal existance
Child lock
DPMS
On, Standby, Power error,...
AV1, AV2, ..., HDMI, PC
Auto, Normal, Full, ...
Dynamic, Standard, ...
Signal / No signal
On / Off
On / Off
RS232C Command Tables
-17-N4HME
TROUBLE SHOOTING
Item Condition Check point
1
2
3
4
5
6
7
8
9
No power
No power
No power
No backlight
Faulty picture
Faulty picture
No RC
No key SW
Fan faulty
** HINT**In most cases the problem is caused by the SUB POWER board or COMPboard.
Try replacing them first, then check the LCD panel.
NO LED
NO LED
LED brighter
After power on, once panel lightsthen keep black out
No colour, poor pictureDarker / brighter picture etc.
Visible line on the picturePart of the display is poor
No working of RC handset
No working or the front key Switch
After indication of the display,then 30 seconds later, come intostandby
Change the FAN
Change the FRONT board
Change the RC or FRONT board
Change the panel
Change the COMP board>>If not, change the panel.
Change the LCD panel
Check to voltage of KR-3 --- 5V
>>Change the power board
Check the fuse on the FILTER board
Check the connection of the AC cord.(AC plug and junction part)
Check the voltage of
Housing KQ-2 ----13V
IC6602 ---- 9V
IC6603 ---- 12V
IC6604 ---- 6V
Housing KR-1 ---- 24V
>>Change the COMP or SUB POWER board
** Refer to the power diagram
-18-N4HME
IC Descriptions for UK4BIC1110This is a switching IC, NJM2233BM, which allows the sync signal input on monitor sets to be switched between pin20 of SCART 1 (conventional) and pin 14 of SCART 1 (SIS signal). The IC takes a 5V supply and is switched by thecontrol line SIS.
IC1205This a ROHM BA7603F triple video switch which allows the RGB input to be switched between SCART 1 andSCART 2. The switch is controlled by the RGB_SW line from the IC.
IC1271This a large multiway electronic switch, MM1631BJBE. Via the I2C lines the cpu can select any audio input L/R pairand feed them to scart 3 or IC801.
IC151BA2904F - this is an OP-AMP used to amplify the AGC voltage back to IC801.
IC1801/1802PCA9534PW - These are I2C expander IC’s. They convert I2C commands from IC801 into control lines.
IC1841/1851These are OP-AMPS used to control the speed of the fans
IC2002/20036db AMP/BUFFERS that compensate for internal loss in the YPbPr / RGB / HV loop.
IC2006RS232 to 5v decoder / encoder. It converts the RS232 signal from K2008 into a TTL signal that can be understoodby the CPU IC2010
IC2007 / 8 / 115v to 3.3v logic conversion for the CPU IC2010
IC2009Reset pulse generator for the CPU IC2010
IC2010CPU with internal program flash memory. The software version programmed into this device can be found in the service menu. The RS232 data is converted into I2C data by this CPU and fed to the main CPU via KCPA.All RS232 protocol are generated by this IC.
IC2012This is a 5v regulator.
IC4001This is a SST SST39VF020 CMOS multi-purpose flash with a capacity of 2Mbits. It is connected to the LOC usingaddress lines, data input/output, write enable and control lines. The flash IC is powered by the 3V3 SW supply.
IC4002This is a ROHM BD5260G open drain voltage detector IC which works in conjunction with the main power and the3.3V standby line to control the back lights.
IC601This is a “current mode PFC controller” operating in transition mode. It is used in conjunction with L603 as activepower phase correction.
-19-N4HME
IC Descriptions for UK4B (continued)IC6600This is an LA5754 voltage regulator. It provides the 12v supply for the LCD panel.
IC6601This is a BA33BC0FP voltage regulator. It converts the 5v standby supply to 3.3v.
IC6602This is a BA09FP-E2 voltage regulator. It converts 13v to 9v.
IC6603This is a BA12FP-E2 12v voltage regulator. It converts the main 13v supply down to 12v for the fan.
IC6604This is a LA5754MP voltage regulator. This IC converts the main 13v supply down to 6v. IC801 can switch this IC onand off via control line “Power 1”. Consequently all supplies developed from this 6v will also be switched (see powerarchitecture diagram on page 8)
IC6605 / 6 / 7 / 8 / 9 / 10These are voltage regulators which convert the switched 6v supply down to 5v, 3.3v and 1.8v.
IC6613This is a TC7SH02 2-INPUT NOR GATE. This IC controls the 5v power to the LCD panel. It is switched via controllines “Power 4” and “Panel on”.
IC701This is a THC63LVDM83R LVDS converter IC. This IC converts 3 sets of 8 bit data (R, G & B) into 4 channel andclock data stream to the LCD panel.
IC8001This is a HDMI receiver / convertor. HDMI data from K1006 is fed into this IC. The IC then extracts the video andaudio in digital format and sends the data to IC801. Audio data is converted to analogue via IC8501
IC801This IC is the main control IC for the entire TV. It incorporates:-1) CPU for control and on-screen graphics presentation.2) Video signal processor for controlling picture presentation and quality.3) LCD scaler for converting different resolutions to the resolution of the LCD.4) 100 page text decoder.5) Stereo sound decoder.6) Multi-system decoder (PAL, NTSC, SECAM etc.)
IC802This is an 8K x 8 bit EEProm. It is used to store all the calibration data and user settings. When a new IC is fitted,the CPU (IC801) will detect it and initialise the IC to the default factory settings.
IC8131This is a 512 x 8 bit EEProm. It is used to store the resolutions that the tv is able to display along with the manufacturer, date of manufacture and model number. An external device (eg DVD) with HDMI will read thisEEProm to determine which resolution signal to send to the tv.
IC8141This is an I2C isolation device
IC8501This is a digital to analogue converter. It is used to convert the HDMI digital audio data to analogue.
IC8502This is a dual OP-AMP and is used to bufffer the HDMI analogue signal to the audio selector IC (IC1271)
-20-N4HME
x xx xxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxx xxxxxxx xxxxxxxxxxxxxxxxxxx
Note: Parts order must contain Service Ref. No., Part No., and descriptions.
�
JXPLA
Item Part No. Description Item Part No. Description
1
2
5/6
7
-28-N4HK
PIN DESCRIPTION OF SEMICONDUCTORS
AK
C
B E
C2C1
B1 B2E
C
CB E
K A
C
B
E
B2B1
C1 C2
E
E
B
C
B2B1
C1 C2
E�
B2
B1C1C2
E1
E2
�
K
A A
A
K K
K
A
K
A
CB
E CB
EC
B
E
1
2
34
5
6
Index
1 2
N
IndexIndex
1 2
N
2
1 3(IN) (OUT)
(GND)
21 4
2
13
Index
1
N
Index1
N
Index1
N
Index1
N
Index1
N
Index
1 N
21
31
2 32
1
3
RESET GND
Vdd
5
3
DG
SD
G
S
K: Cathode�A: Anode
C: Collector�B: Base�E: Emitter
D: Drain�G: Gate�S: Source
● Diode
● Transistor/FET
● IC
E1C2
E2 C1B2
B1
Index
● Diode
● Transistor/FET
● IC
FET
N4HME
-29-
CHASSIS ELECTRICAL PARTS LIST
Product safety should be considered when a component replacement is made in any area of a receiver. Components indicated by a mark in this parts list and the circuit diagram show components whose value havespecial significance to product safety. It is particularly recommended that only parts specified on the followingparts list be used for components replacement pointed out by the mark .!
!
Note: Parts order must contain Service Ref. No., Part No., and descriptions.
CE32LM4WPR-E
CHASSIS PARTS1 665 001 0048 ASSY,PWB,MAIN,N4HM2 665 001 0055 ASSY,PWB,POWER DELTA 3 665 000 8465 ASSY,PWB,CONTROL,N4HLW (FITTED ON FRONT EXTRUSION)4 665 001 0062 ASSY,PWB,SUB AV C5 645 068 3763 MOTOR,FAN DC
PANEL, SPACER AND GASKET665 000 9752 T-COPPER FOIL*1821*W25
