Date post: | 21-Jan-2016 |
Category: |
Documents |
Upload: | mario-contreras |
View: | 1,018 times |
Download: | 26 times |
Service ManualContents
This service manual contains information of different types of models.Make sure to refer to the section describing your model.
TYPE A32PFL3506/F7 PHILIPS (Serial No.: DS1)
32PFL3506/F7 PHILIPS (Serial No.: XA1)
32PFL3000/F8 PHILIPS (Serial No.: XA1)
TYPE B32PFL3506/F7 PHILIPS (Serial No.: DS2)
32PFL3506/F7 PHILIPS (Serial No.: DS3)
32PFL3000/F8 PHILIPS (Serial No.: XA2)
32” LCD TVchassis PL11.0
111128
© 2011 Funai Electric Co., Ltd.
All rights reserved. No part of this manual may be reproduced, copied, transmitted, disseminated, transcribed, downloaded or stored in any storage medium, in any form or for any purpose without the express prior written consent of Funai. Furthermore, any unauthorized commercial distribution of this manual or any revision hereto is strictly prohibited.
Information in this document is subject to change without notice. Funai reserves the right to change the content herein without the obligation to notify any person or organization of such changes.
with the design is a registered trademark of Funai Electric Co., Ltd and may not be used in any way without the express written consent of Funai. All other trademarks used herein remain the exclusive property of their respective owners. Nothing contained in this manual should be construed as granting, by implication or otherwise, any license or right to use any of the trademarks displayed herein. Misuse of any trademarks or any other content in this manual is strictly prohibited. Funai shall aggressively enforce its intellectual property rights to the fullest extent of the law.
IMPORTANT SAFETY NOTICE
Proper service and repair is important to the safe, reliable operation of all P&F Equipment. The service procedures recommended by P&F and described in this service manual are effective methods of performing service operations. Some of these service special tools should be used when and as recommended.
It is important to note that this service manual contains various CAUTIONS and NOTICES which should be carefully read in order to minimize the risk of personal injury to service personnel. The possibility exists that improper service methods may damage the equipment. It also is important to understand that these CAUTIONS and NOTICES ARE NOT EXHAUSTIVE. P&F could not possibly know, evaluate and advice the service trade of all conceivable ways in which service might be done or of the possible hazardous consequences of each way. Consequently, P&F has not undertaken any such broad evaluation. Accordingly, a servicer who uses a service procedure or tool which is not recommended by P&F must first use all precautions thoroughly so that neither his safety nor the safe operation of the equipment will be jeopardized by the service method selected.
The LCD panel is manufactured to provide many years of useful life. Occasionally a few non active pixels may appear as a tiny spec of color. This is not to be considered a defect in the LCD screen.
TABLE OF CONTENTS
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1Important Safety Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1Standard Notes for Servicing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1Cabinet Disassembly Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1Electrical Adjustment Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1 How to Initialize the LCD TV . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-1Firmware Renewal Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-1 Troubleshooting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-1Block Diagrams [TYPE A] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-1
[TYPE B] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-7Schematic Diagrams / CBA and Test Points . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-1Waveforms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-1Wiring Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-1Exploded Views. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-1Parts List [TYPE A] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14-1
[TYPE B] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14-12Revision History . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15-1
1-1 PL11.0SP
SPECIFICATIONS
< TUNER / NTSC >ANT. Input ---------------------- 75 Ω Unbal., F type
< TUNER / ATSC >
< LCD PANEL >
< VIDEO >
< AUDIO >
All items are measured across 8 Ω load at speaker output terminal with L.P.F.
Description Condition Unit Nominal Limit
1. AFT Pull-In Range --- MHz ±2.3 ±2.1
2. Synchronizing Sens.TV.ch.4
CA.ch.31CA.ch.87
dBµdBµdBµ
181818
202023
Description Condition Unit Nominal Limit
1. Received Freq. Range (-28dBm) --- kHz --- ±100
2. ATSC Dynamic Range (min / max)ch.4ch.10ch.41
dBmdBmdBm
---------
-76/0-76/0-76/0
Description Condition Unit Nominal Limit
1. Native Pixel Resolution HorizontalVertical
pixelspixels
1366768
------
2. Brightness (w / filter) --- cd/m2 350 ---
3. Viewing Angle HorizontalVertical
°°
-88 to 88-88 to 88
------
Description Condition Unit Nominal Limit
1. Over Scan HorizontalVertical
%%
55
5±55±5
2. Color Temperature---xy
°K 120000.2720.278
---±3%±3%
3. Resolution (composite video) HorizontalVertical
lineline
400350
------
Description Condition Unit Nominal Limit
1. Audio Max Output (ATSC 0 dBfs) Lch/Rch W 10.0/10.0 8.0/8.0
2. Audio Distortion (NTSC) 500mW: Lch/Rch % 0.5/0.5 2.0/2.0
3. Audio Freq. Response (NTSC) -6dB: Lch-6dB: Rch
HzHz
70 to 10 k70 to 10 k
------
2-1 LTVN_ISP
IMPORTANT SAFETY PRECAUTIONS
Prior to shipment from the factory, our products are strictly inspected for recognized product safety and electrical codes of the countries in which they are to be sold. However, in order to maintain such compliance, it is equally important to implement the following precautions when a set is being serviced.
Safety Precautions for LCD TV Circuit1. Before returning an instrument to the
customer, always make a safety check of the entire instrument, including, but not limited to, the following items:
a. Be sure that no built-in protective devices are defective and have been defeated during servicing. (1) Protective shields are provided on this chassis to protect both the technician and the customer. Correctly replace all missing protective shields, including any removed for servicing convenience. (2) When reinstalling the chassis and/or other assembly in the cabinet, be sure to put back in place all protective devices, including but not limited to, nonmetallic control knobs, insulating fishpapers, adjustment and compartment covers/shields, and isolation resistor/capacitor networks. Do not operate this instrument or permit it to be operated without all protective devices correctly installed and functioning. Servicers who defeat safety features or fail to perform safety checks may be liable for any resulting damage.
b. Be sure that there are no cabinet openings through which an adult or child might be able to insert their fingers and contact a hazardous voltage. Such openings include, but are not limited to, (1) spacing between the Liquid Crystal Panel and the cabinet mask, (2) excessively wide cabinet ventilation slots, and (3) an improperly fitted and/or incorrectly secured cabinet back cover.
c. Antenna Cold Check - With the instrument AC plug removed from any AC source, connect an electrical jumper across the two AC plug prongs. Place the instrument AC switch in the on position. Connect one lead of an ohmmeter to the AC plug prongs tied together and touch the other ohmmeter lead in turn to each tuner antenna input exposed terminal screw and, if applicable, to the coaxial connector. If the measured resistance is less than 1.0 megohm or greater than 5.2 megohm, an abnormality exists that must be corrected before the instrument is returned to the customer. Repeat this test with the instrument AC switch in the off position.
d. Leakage Current Hot Check - With the instrument completely reassembled, plug the AC line cord directly into a 120 V AC outlet. (Do not use an isolation transformer during this test.) Use a leakage current tester or a metering system that complies with American National Standards Institute (ANSI) C101.1 Leakage Current for Appliances and Underwriters Laboratories (UL) 1410, (50.7). With the instrument AC switch first in the on position and then in the off position, measure from a known earth ground (metal water pipe, conduit, etc.) to all exposed metal parts of the instrument (antennas, handle brackets, metal cabinet, screw heads, metallic overlays, control shafts, etc.), especially any exposed metal parts that offer an electrical return path to the chassis. Any current measured must not exceed 0.5 milli-ampere. Reverse the instrument power cord plug in the outlet and repeat the test.
ANY MEASUREMENTS NOT WITHIN THE LIMITS SPECIFIED HEREIN INDICATE A POTENTIAL SHOCK HAZARD THAT MUST BE ELIMINATED BEFORE RETURNING THE INSTRUMENT TO THE CUSTOMER OR BEFORE CONNECTING THE ANTENNA OR ACCESSORIES.
2. Read and comply with all caution and safety-related notes on or inside the receiver cabinet, on the receiver chassis, or on the Liquid Crystal Panel.
ALSO TEST WITHPLUG REVERSEDUSING ACADAPTER PLUGAS REQUIRED
TEST ALL EXPOSEDMETAL SURFACES
READING SHOULD NOT BE ABOVE 0.5 mA
EARTHGROUND
_
DEVICELEAKAGECURRENT
TESTER
+BEINGTESTED
2-2 LTVN_ISP
3. Design Alteration Warning - Do not alter or add to the mechanical or electrical design of this TV receiver. Design alterations and additions, including, but not limited to circuit modifications and the addition of items such as auxiliary audio and/or video output connections, might alter the safety characteristics of this receiver and create a hazard to the user. Any design alterations or additions will void the manufacturer's warranty and may make you, the servicer, responsible for personal injury or property damage resulting therefrom.
4. Hot Chassis Warning -
a. Some TV receiver chassis are electrically connected directly to one conductor of the AC power cord and maybe safety-serviced without an isolation transformer only if the AC power plug is inserted so that the chassis is connected to the ground side of the AC power source. To confirm that the AC power plug is inserted correctly, with an AC voltmeter, measure between the chassis and a known earth ground. If a voltage reading in excess of 1.0 V is obtained, remove and reinsert the AC power plug in the opposite polarity and again measure the voltage potential between the chassis and a known earth ground.
b. Some TV receiver chassis normally have 85V AC(RMS) between chassis and earth ground regardless of the AC plug polarity. This chassis can be safety-serviced only with an isolation transformer inserted in the power line between the receiver and the AC power source, for both personnel and test equipment protection.
c. Some TV receiver chassis have a secondary ground system in addition to the main chassis ground. This secondary ground system is not isolated from the AC power line. The two ground systems are electrically separated by insulation material that must not be defeated or altered.
5. Observe original lead dress. Take extra care to assure correct lead dress in the following areas: a. near sharp edges, b. near thermally hot parts-be sure that leads and components do not touch thermally hot parts, c. the AC supply, d. high voltage, and, e. antenna wiring. Always inspect in all areas for pinched, out of place, or frayed wiring. Check AC power cord for damage.
6. Components, parts, and/or wiring that appear to have overheated or are otherwise damaged should be replaced with components, parts, or wiring that meet original specifications. Additionally, determine the cause of overheating and/or damage and, if necessary, take corrective action to remove any potential safety hazard.
7. Product Safety Notice - Some electrical and mechanical parts have special safety-related characteristics which are often not evident from visual inspection, nor can the protection they give necessarily be obtained by replacing them with components rated for higher voltage, wattage, etc. Parts that have special safety characteristics are identified by a # on schematics and in parts lists. Use of a substitute replacement that does not have the same safety characteristics as the recommended replacement part might create shock, fire, and/or other hazards. The product's safety is under review continuously and new instructions are issued whenever appropriate. Prior to shipment from the factory, our products are strictly inspected to confirm they comply with the recognized product safety and electrical codes of the countries in which they are to be sold. However, in order to maintain such compliance, it is equally important to implement the following precautions when a set is being serviced.
2-3 LTVN_ISP
Precautions during ServicingA. Parts identified by the # symbol are critical for
safety.Replace only with part number specified.
B. In addition to safety, other parts and assemblies are specified for conformance with regulations applying to spurious radiation. These must also be replaced only with specified replacements.Examples: RF converters, RF cables, noise blocking capacitors, and noise blocking filters, etc.
C. Use specified internal wiring. Note especially:
1) Wires covered with PVC tubing
2) Double insulated wires
3) High voltage leads
D. Use specified insulating materials for hazardous live parts. Note especially:
1) Insulation Tape
2) PVC tubing
3) Spacers
4) Insulators for transistors.
E. When replacing AC primary side components (transformers, power cord, etc.), wrap ends of wires securely about the terminals before soldering.
F. Observe that the wires do not contact heat producing parts (heat sinks, oxide metal film resistors, fusible resistors, etc.)
G. Check that replaced wires do not contact sharp edged or pointed parts.
H. When a power cord has been replaced, check that 11~13 lb (5~6 kg) of force in any direction will not loosen it.
I. Also check areas surrounding repaired locations.
J. Use care that foreign objects (screws, solder droplets, etc.) do not remain inside the set.
K. When connecting or disconnecting the internal connectors, first, disconnect the AC plug from the AC supply outlet.
L. When installing parts or assembling the cabinet parts, be sure to use the proper screws and tighten certainly.
2-4 LTVN_ISP
Safety Check after ServicingExamine the area surrounding the repaired location for damage or deterioration. Observe that screws, parts and wires have been returned to original positions. Afterwards, perform the following tests and confirm the specified values in order to verify compliance with safety standards.
1. Clearance Distance
When replacing primary circuit components, confirm specified clearance distance (d) and (d') between soldered terminals, and between terminals and surrounding metallic parts. (See Fig. 1)
Table 1: Ratings for selected area
Note: This table is unofficial and for reference only. Be sure to confirm the precise values.
2. Leakage Current Test
Confirm the specified (or lower) leakage current between B (earth ground, power cord plug prongs) and externally exposed accessible parts (RF terminals, antenna terminals, video and audio input and output terminals, microphone jacks, earphone jacks, etc.) is lower than or equal to the specified value in the table below.
Measuring Method: (Power ON)
Insert load Z between B (earth ground, power cord plug prongs) and exposed accessible parts. Use an AC voltmeter to measure across both terminals of load Z. See Fig. 2 and following table.
Table 2: Leakage current ratings for selected areas
Note: This table is unofficial and for reference only. Be sure to confirm the precise values.
AC Line Voltage Region Clearance Distance (d), (d’)
110 to 130 V U.S.A. or Canada
≥ 3.2 mm (0.126 inches)
AC Line Voltage Region Load Z Leakage Current (i) Earth Ground (B) to:
110 to 130 V U.S.A. or Canada
0.15 µF CAP. & 1.5 kΩ RES. Connected in parallel i ≤ 0.5 mA rms Exposed accessible
parts
Chassis or Secondary Conductor
Primary Circuit
Fig. 1
d' d
AC Voltmeter (High Impedance)
Exposed Accessible Part
B Earth Ground Power Cord Plug Prongs
Z
Fig. 2
3-1 TVN_SN
STANDARD NOTES FOR SERVICING
Circuit Board Indications1. The output pin of the 3 pin Regulator ICs is
indicated as shown.
2. For other ICs, pin 1 and every fifth pin are indicated as shown.
3. The 1st pin of every male connector is indicated as shown.
Pb (Lead) Free SolderPb free mark will be found on PCBs which use Pb free solder. (Refer to figure.) For PCBs with Pb free mark, be sure to use Pb free solder. For PCBs without Pb free mark, use standard solder.
How to Remove / Install Flat Pack-IC
1. Removal
With Hot-Air Flat Pack-IC Desoldering Machine:
1. Prepare the hot-air flat pack-IC desoldering machine, then apply hot air to the Flat Pack-IC (about 5 to 6 seconds). (Fig. S-1-1)
2. Remove the flat pack-IC with tweezers while applying the hot air.
3. Bottom of the flat pack-IC is fixed with glue to the CBA; when removing entire flat pack-IC, first apply soldering iron to center of the flat pack-IC and heat up. Then remove (glue will be melted). (Fig. S-1-6)
4. Release the flat pack-IC from the CBA using tweezers. (Fig. S-1-6)
CAUTION:
1. The Flat Pack-IC shape may differ by models. Use an appropriate hot-air flat pack-IC desoldering machine, whose shape matches that of the Flat Pack-IC.
2. Do not supply hot air to the chip parts around the flat pack-IC for over 6 seconds because damage to the chip parts may occur. Put masking tape around the flat pack-IC to protect other parts from damage. (Fig. S-1-2)
Top View
Out In
Bottom ViewInput
5
10
Pin 1
Pin 1
Pb free mark
Fig. S-1-1
3-2 TVN_SN
3. The flat pack-IC on the CBA is affixed with glue, so be careful not to break or damage the foil of each pin or the solder lands under the IC when removing it.
With Soldering Iron:
1. Using desoldering braid, remove the solder from all pins of the flat pack-IC. When you use solder flux which is applied to all pins of the flat pack-IC, you can remove it easily. (Fig. S-1-3)
2. Lift each lead of the flat pack-IC upward one by one, using a sharp pin or wire to which solder will not adhere (iron wire). When heating the pins, use a fine tip soldering iron or a hot air desoldering machine. (Fig. S-1-4)
3. Bottom of the flat pack-IC is fixed with glue to the CBA; when removing entire flat pack-IC, first apply soldering iron to center of the flat pack-IC and heat up. Then remove (glue will be melted). (Fig. S-1-6)
4. Release the flat pack-IC from the CBA using tweezers. (Fig. S-1-6)
Hot-airFlat Pack-ICDesolderingMachine
CBA
Flat Pack-IC
Tweezers
Masking Tape
Fig. S-1-2
Flat Pack-IC Desoldering Braid
Soldering Iron
Fig. S-1-3
Fine TipSoldering Iron
SharpPin
Fig. S-1-4
3-3 TVN_SN
With Iron Wire:
1. Using desoldering braid, remove the solder from all pins of the flat pack-IC. When you use solder flux which is applied to all pins of the flat pack-IC, you can remove it easily. (Fig. S-1-3)
2. Affix the wire to a workbench or solid mounting point, as shown in Fig. S-1-5.
3. While heating the pins using a fine tip soldering iron or hot air blower, pull up the wire as the solder melts so as to lift the IC leads from the CBA contact pads as shown in Fig. S-1-5.
4. Bottom of the flat pack-IC is fixed with glue to the CBA; when removing entire flat pack-IC, first apply soldering iron to center of the flat pack-IC and heat up. Then remove (glue will be melted). (Fig. S-1-6)
5. Release the flat pack-IC from the CBA using tweezers. (Fig. S-1-6)
Note: When using a soldering iron, care must be taken to ensure that the flat pack-IC is not being held by glue. When the flat pack-IC is removed from the CBA, handle it gently because it may be damaged if force is applied.
2. Installation1. Using desoldering braid, remove the solder from
the foil of each pin of the flat pack-IC on the CBA so you can install a replacement flat pack-IC more easily.
2. The “ I ” mark on the flat pack-IC indicates pin 1. (See Fig. S-1-7.) Be sure this mark matches the pin 1 on the PCB when positioning for installation. Then presolder the four corners of the flat pack-IC. (See Fig. S-1-8.)
3. Solder all pins of the flat pack-IC. Be sure that none of the pins have solder bridges.
To Solid Mounting Point
Soldering Iron
Iron Wire
or
Hot Air Blower
Fig. S-1-5
Fine TipSoldering IronCBA
Flat Pack-ICTweezers
Fig. S-1-6
Example :
Pin 1 of the Flat Pack-ICis indicated by a " " mark. Fig. S-1-7
Presolder
CBA
Flat Pack-IC
Fig. S-1-8
3-4 TVN_SN
Instructions for Handling Semi-conductorsElectrostatic breakdown of the semi-conductors may occur due to a potential difference caused by electrostatic charge during unpacking or repair work.
1. Ground for Human Body
Be sure to wear a grounding band (1 MΩ) that is properly grounded to remove any static electricity that may be charged on the body.
2. Ground for Workbench
Be sure to place a conductive sheet or copper plate with proper grounding (1 MΩ) on the workbench or other surface, where the semi-conductors are to be placed. Because the static electricity charge on clothing will not escape through the body grounding band, be careful to avoid contacting semi-conductors with your clothing.
<Incorrect>
CBA
Grounding Band
Conductive Sheet orCopper Plate
1MΩ
1MΩ
<Correct>
CBA
4-1 PL11.0-A_DC
CABINET DISASSEMBLY INSTRUCTIONS
1. Disassembly FlowchartThis flowchart indicates the disassembly steps for the cabinet parts and the CBA in order to gain access to items to be serviced. When reassembling, follow the steps in reverse order. Bend, route and dress the cables as they were.
2. Disassembly Method
*1: TYPE A
*2: TYPE B
Note:
(1) Order of steps in procedure. When reassembling, follow the steps in reverse order. These numbers are also used as the Identification (location) No. of parts in figures.
(2) Parts to be removed or installed.
(3) Fig. No. showing procedure of part location
(4) Identification of parts to be removed, unhooked, unlocked, released, unplugged, unclamped, or desoldered. P = Spring, L = Locking Tab, S = Screw, H = Hex Screw, CN = Connectore.g. 2(S-2) = two Screws of (S-2), 2(L-2) = two Locking Tabs of (L-2)
(5) Refer to the following "Reference Notes in the Table."
Step/Loc. No.
Part Fig. No. Removal Note
[1] Stand Assembly D1 3(S-1) ---
[2] Rear Assembly D1 12(S-2), 2(S-3),
4(S-4), 11(L-1) ---
[3] Inverter CBA
D2D4
7(S-5), CN1001, CN1003, CN1100, CN1101, CN1102, CN1901
---
[4] Jack CBA D2D4 2(S-6), CL701B ---
[5]Power Supply CBA
D2D4
9(S-7), CN101, CN301, CN302, CN801, CN802
---
[6] Digital Main CBA Unit
D2D4
2(S-8), 8(S-9), CN3902*1, CN3005*2, Jack Holder, Shield Box
---
[7] Speaker D3 4(S-10), Speaker Holder ---
[1] StandAssembly
[2] Rear Assembly [7] Speaker
[3] Inverter CBA
[4] Jack CBA
[6] Digital MainCBA Unit
[5] Power SupplyCBA
[10] LCD ModuleAssembly
[11] FrontCabinet
[8] IR SensorCBA
[9] FunctionCBA
[8] IR Sensor CBA
D3D4 CL103A ---
[9] Function CBA
D3D4
Function Knob, Knob Frame ---
[10]LCD Module Assembly
D3 (S-11) ---
[11] Front Cabinet D3 --------------- ---
↓(1)
↓(2)
↓(3)
↓(4)
↓(5)
Step/Loc. No.
Part Fig. No. Removal Note
4-2 PL11.0-A_DC
[2] Rear Assembly
(S-1)
[1] Stand Assembly
(S-2)
(S-2)
(S-2)
(S-2)
(S-3)
(S-2)
(S-4)
(S-4)
(L-1)
(L-1)
(L-1)(L-1)
Fig. D1
4-3 PL11.0-A_DC
(S-5)
[4] Jack CBA
Jack Holder
[5] Power Supply CBA
[6] Digital Main CBA Unit
[3] Inverter CBA
(S-6)
(S-7)
(S-8)
(S-9)
(S-9)
Shield Box(S-7)
Fig. D2
4-4 PL11.0-A_DC
(S-10)
(S-11)
[10] LCD Module Assembly
[8] IR Sensor CBA
[9] Function CBA
SpeakerHolder
[7] Speaker
[7] Speaker
[11] Front Cabinet
Knob Frame
Function Knob
Fig. D3
4-5 PL11.0-A_DC
TV Cable Wiring Diagram
Power Supply CBA
Jack CBA
CN201CN1001
CN1003
CN3702
CN1100
CN1101
CN1102
Digital Main CBA Unit
CN1901
Inverter CBA
CN802
AC CORD
CL701B
CN302
CL701A
CN801
CN602
CN101CN301
CL103B
CL103A CL102B
FunctionCBA
IR SensorCBA
To LCD Module Assembly
To Speaker
To LCD Module Assembly
TYPE ACN3006TYPE B
CN3701TYPE ACN3002TYPE B
CN3902TYPE ACN3005TYPE B
Fig. D4
5-1 A17F6EA
ELECTRICAL ADJUSTMENT INSTRUCTIONS
[32PFL3506/F7 (Serial No.: DS1, XA1), 32PFL3000/F8 (Serial No.: XA1)]General Note: “CBA” is abbreviation for “Circuit Board Assembly.”Note: Electrical adjustments are required after
replacing circuit components and certain mechanical parts. It is important to perform these adjustments only after all repairs and replacements have been completed. Also, do not attempt these adjustments unless the proper equipment is available.
Test Equipment Required1. NTSC Pattern Generator (Color Bar W/White
Window, Red Color, Dot Pattern, Gray Scale, Monoscope, Multi-Burst)
2. Remote control unit
3. Color Analyzer
How to set up the service mode:
Service mode:1. Turn the power on.
2. Press [MENU] button to display Setup menu.
3. Select “Features”.
4. Select “Current Software Info”.
5. Press [0], [6], [2], [5], [9], [6] and [INFO] buttons on the remote control unit in this order. The following screen appears.
Code : Pic code : MIPS :
Press "POWER" key to exit.
*******-***-*-*****-**** **-*******-*****-**Push 0key
Tuner : Safety :
****-*****-****safety_Non
"*" differs depending on the models.
5-2 A17F6EA
1. Purity Check ModeThis mode cycles through full-screen displays of red, green, blue, and white to check for non-active pixels.
1. Enter the Service mode.
2. Each time the [7] button on the remote control unit is pressed, the display changes as follows.
3. To cancel or to exit from the Purity Check Mode, press [PREV CH] button.
2. VCOM Adjustment
1. Set the color analyzer at the zero point calibration and bring the optical receptor pointing at the center of the LCD-Panel at a distance of 1.18 inches(3cm) away from the LCD-Panel surface.Note: The optical receptor must be set perpendicularly to the LCD Panel surface.
2. Enter the Service mode.
3. Press [2] button on the remote control unit.
4. Press [CH + or -] buttons on the remote control unit so that the color analyzer value becomes minimum within 2minutes from Power-On.
5. To cancel or to exit from the VCOM Adjustment, press [PREV CH] button.
[7] button
Note:When entering this mode, the default setting is White mode.
Purity Check Mode
[7] button
Red mode
Green mode
Blue mode
Black mode
[7] button
White mode
[7] button
[7] button
White 20% mode[7] button
Test Point Adj. Point
Screen [CH + or -] buttons
M. EQ. Spec.
Color analyzer See below
Figure
Color Analyzer
To avoid interference from ambient light, this adjustment should be performed in a dark room.
L = 1.18 inches
Perpendicularity
5-3 A17F6EA
The White Balance Adjustment should be performed when replacing the LCD Panel or Digital Main CBA.
3. White Balance AdjustmentPurpose: To mix red and blue beams correctly for pure white.
Symptom of Misadjustment: White becomes bluish or reddish.
1. Operate the unit for more than 60 minutes.
2. Input the White Raster(70%=70IRE, 40%=40IRE).
3. Set the color analyzer at the CHROMA mode and zero point calibration. Bring the optical receptor pointing at the center of the LCD-Panel at a distance of 1.18 inches(3cm) away from the LCD-Panel surface.Note: The optical receptor must be set perpendicularly to the LCD Panel surface.
4. Enter the Service mode. Press [VOL -] button on the remote control unit and select “C/D” mode.
5. [CUTOFF]Press [1] button to select “COR” for Red Cutoff adjustment. Press [3] button to select “COB” for Blue Cutoff adjustment.[DRIVE]Press [4] button to select “DR” for Red Drive adjustment. Press [6] button to select “DB” for Blue Drive adjustment.
6. In each color mode, press [CH + or -] buttons to adjust the values of color.
7. Adjust Cutoff and Drive so that the color temperature becomes 12000°K (x= 0.272 / y= 0.278 ± 0.005).
8. To cancel or to exit from the White Balance Adjustment, press [PREV CH] button.
Test Point Adj. Point Mode Input
Screen [VOL -]button
[VIDEO1]C/D
White Raster (APL 70%)
or(APL 40%)
M. EQ. Spec.
Pattern Generator, Color analyzer
x= 0.272 ± 0.005y= 0.278 ± 0.005
Figure
Color Analyzer
Perpendicularity
INPUT: WHITE 70%, 40%
To avoid interference from ambient light, this adjustment should be performed in a dark room.
L = 1.18 inches
40%=40IRE 70%=70IRE100IRE100IRE
0IRE 0IRE
INPUT SIGNAL
LowLight
HighLight
5-4 A17FG_HEA
[32PFL3506/F7 (Serial No.: DS2, DS3), 32PFL3000/F8 (Serial No.: XA2)]General Note: “CBA” is abbreviation for “Circuit Board Assembly.”Note: Electrical adjustments are required after
replacing circuit components and certain mechanical parts. It is important to perform these adjustments only after all repairs and replacements have been completed. Also, do not attempt these adjustments unless the proper equipment is available.
Test Equipment Required1. Remote control unit
2. Color Analyzer, CA-310 (KONICA MINOLTA Luminance meter) or measuring instrument as good as CA-310.
How to set up the service mode:
Service mode:1. Turn the power on.
2. Press [MENU] button to display Setup menu.
3. Select “Features”.
4. Select “Current Software Info”.
5. Press [0], [6], [2], [5], [9], [6] and [INFO] buttons on the remote control unit in this order. The following screen appears.
Code: Pic code:Panel-Option code:MIPS:
Press "POWER" key to exit.
*******-**-**-****-************-***-*-****-***-***-***-***Push 0 key
Tuner: Safety:HDMI EDID: PC EDID:
****-*****-****Safety_Non****
Total Watch Time: Lightsensor:
*********
"*" differs depending on the models.
5-5 A17FG_HEA
1. Purity Check ModeThis mode cycles through full-screen displays of red, green, blue, and white to check for non-active pixels.
1. Enter the Service mode.
2. Each time the [7] button on the remote control unit is pressed, the display changes as follows.
3. To cancel or to exit from the Purity Check Mode, press [PREV CH] button.
2. VCOM Adjustment
32PFL3506/F7 (Serial No.: DS2), 32PFL3000/F8 (Serial No.: XA2):1. Set the color analyzer at the zero point calibration
and bring the optical receptor pointing at the center of the LCD-Panel.Note: The optical receptor must be set perpendicularly to the LCD Panel surface.
2. Enter the Service mode.
3. Press [2] button on the remote control unit.
4. Press [CH + or -] buttons on the remote control unit so that the color analyzer value becomes minimum.
5. To cancel or to exit from the VCOM Adjustment, press [PREV CH] button.
32PFL3506/F7 (Serial No.: DS3):1. Operate the unit for more than 60 minutes.
2. Set the color analyzer at the zero point calibration and bring the optical receptor pointing at the center of the LCD-Panel.Note: The optical receptor must be set perpendicularly to the LCD Panel surface.
3. Enter the Service mode.
4. Press [3] button on the remote control unit.
5. Press [CH + or -] buttons on the remote control unit so that the color analyzer value becomes minimum within 2minutes from Power-On.
6. To cancel or to exit from the VCOM Adjustment, press [PREV CH] button.
[7] button
Note:When entering this mode, the default setting is White mode.
Purity Check Mode
[7] button
Red mode
Green mode
Blue mode
Black mode
[7] button
White mode
[7] button
[7] button
White 20% mode[7] button
Test Point Adj. Point
Screen [CH + or -]buttons
M. EQ. Spec.
Color analyzer See below
Figure
Color Analyzer
To avoid interference from ambient light, this adjustment should be performed in a dark room.
Perpendicularity
5-6 A17FG_HEA
The White Balance Adjustment should be performed when replacing the LCD Panel or Digital Main CBA.
3. White Balance AdjustmentPurpose: To mix red and blue beams correctly for pure white.
Symptom of Misadjustment: White becomes bluish or reddish.
1. Operate the unit for more than 60 minutes.
2. Enter the Service mode.
3. Press [VOL -] button three times on the remote control unit to select “Drive setting” mode. “Drive” appears on the screen.
4. Set the color analyzer at the CHROMA mode and zero point calibration. Bring the optical receptor pointing at the center of the LCD-Panel.
Note: The optical receptor must be set perpendicularly to the LCD Panel surface.
5. Press [3] button to select the “HDB” for High Drive Blue adjustment. (“HDB” appears on the screen.)
6. Press [MENU] button. The internal Raster signal appears on the screen. (“Internal (Single)” appears on the upper right of the screen as shown below.)
7. Press [CH + or -] buttons to adjust the color temperature becomes 12000°K (x= 0.272 / y= 0.278 ±0.002).
8. Press [1] button to select the “HDR” for High Drive Red adjustment (“HDR” appears on the screen.) and press [CH + or -] buttons to adjust the color temperature.
9. If necessary, adjust the “HDB” or “HDR” again.
10. Press [6] button to select the “LDB” for Low Drive Blue adjustment (“LDB” appears on the screen.) and press [CH + or -] buttons to adjust the color temperature.
11. Press [4] button to select the “LDR” for Low Drive Red adjustment (“LDR” appears on the screen.) and press [CH + or -] buttons to adjust the color temperature.
12. If necessary, adjust the “LDB” or “LDR” again.
13. Press [VOL -] button to shift to the “Debugging Message” mode. If there is no message under “[WB]” section, this adjustment completes. If “Drive settings are NG. Retry.” is displayed, repeat above steps from 5. to 12. Then check “Debugging Message” again. If “Drive settings are NG. Retry.” is displayed, replace the LCD Panel or Digital Main CBA.
14. To cancel or to exit from the White Balance Adjustment, press [PREV CH] button.
ITEM SPECIFICATION
Color temperature x= 0.272 ± 0.002y= 0.278 ± 0.002
Input Signal Internal pattern (40/70% raster)
Measurement point Screen center
M. EQ.
CA-310 (KONICA MINOLTA Luminance meter) or measuring instrument as good as CA-310.
Aging time60min. (Retail MODE/100IRE Raster HDMI 1080i@60)
MODE setting of TV Shipment setting/Retail MODE
Ambient temperature 25°C ± 5°C
Color Analyzer
Perpendicularity
To avoid interference from ambient light, this adjustment should be performed in a dark room.
Internal (Single)
HDB 0
Internal (Single)
LDB 0
6-1 A17F6INT
HOW TO INITIALIZE THE LCD TV
The purpose of initialization is to place the set in a new out of box condition. The customer will be prompted to select a language and program channels after the set has been initialized.To put the program back at the factory-default, initialize the LCD TV using the following procedure.
[32PFL3506/F7 (Serial No.: DS1, XA1), 32PFL3000/F8 (Serial No.: XA1)]1. Turn the power on.
2. Enter the service mode.
- To cancel the service mode, press [ ] button on the remote control unit.
3. Press [INFO] button on the remote control unit to initialize the LCD television.
4. "INITIALIZED" will appear in the upper right of the screen. "INITIALIZED" color will change to green from red when initializing is completed.
[32PFL3506/F7 (Serial No.: DS2, DS3),32PFL3000/F8 (Serial No.: XA2)]1. Turn the power on.
2. Enter the service mode.
- To cancel the service mode, press [ ] button on the remote control unit.
3. Press [FREEZE] button on the remote control unit to initialize the LCD television.
4. "INITIALIZED" will appear in the upper right of the screen. "INITIALIZED" color will change to green from red when initializing is completed.
7-1 PL11.0FW
FIRMWARE RENEWAL MODE
Equipment Requireda. USB storage deviceb. Remote Control Unit
Firmware Update ProcedureNote: There are two states (the User Upgrade and
the Factory Upgrade) in firmware update.
*1: 32PFL3506/F7 (Serial No.: DS2, DS3), 32PFL3000/F8 (Serial No.: XA2)
The identification of User Upgrade and Factory Upgrade are done by the filename.
1. Turn the power off and unplug the AC Cord.
2. Insert the USB storage device to the USB port as shown below.
3. Plug the AC cord in the wall outlet and turn the power on.
4. The update will start and the following will appear on the screen.
Note: If the above screen isn’t displayed, repeat from step 1.
The appearance shown in *1 is described as follows.
5. When the firmware update is completed, the following will appear on the screen.
Remove the USB storage device from the USB port. Turn the power off and turn the power on again.
Note:
When the Factory Upgrade is used, after restarting TV, shift to initial screen menu in service mode. "INITIALIZED" will appear on the upper right of the screen. "INITIALIZED" color will change to green from red when initializing is completed.
User Upgrade Upgrade the firmware only. The setting values are not initialized.
Factory upgrade Upgrade the firmware and initialize the setting values.
*1 Factory Upgrade (Flash upgrade)
Upgrade the firmware and initialize the setting values along with the setting data adjusted at the factory such as White Balance, etc.
USB storage device
Rear Cabinet
Appearance State
Downloading... Downloading the firmware from the USB storage device.
Writing... Writing the downloaded firmware in flash memory.
Checking... Checking the new firmware.
Software upgrade in progress. Please wait.Do not remove the USB storage device or turn the TV off while upgrade is in progress.
Software Upgrade
Downloading...
Current Version:New Version:
*******-***-*-***-***********-***-*-***-****
0%*1
"*" differs depending on the models.
Software Upgrade
The software upgrade is completed.Remove USB storage device, turn TV off then on again.
8-1 PL11.0TR
TROUBLESHOOTING
[ Power Supply Section ]
The power cannot be turned on.
The fuse blows out.
FLOW CHART NO.1
FLOW CHART NO.2
Is normal state restored when once unpluggedpower cord is plugged again after several seconds?
Check if there is any leak or short-circuiting on theprimary circuit component, and service it if defective.(C605, D601, D602, D603, D604, Q601, Q602, Q603, Q604, IC602, T601)
Yes
No
Yes
Is the fuse (F601) normal? See FLOW CHART No.2 <The fuse blows out.>
No
Yes
Is the AL+33V line voltage normal?No
Check each rectifying circuit of the secondarycircuit and service it if defective.
Check the presence that the primary componentis leaking or shorted and service it if defective.
Check the presence that the rectifying diode or circuit is shorted in each rectifying circuit of secondary side, and service it if defective.
After servicing, replace the fuse.
When the output voltage fluctuates.FLOW CHART NO.3
Does the photocoupler circuit on the secondary side operate normally?
No
Yes
Check IC601, D639, D652, D653, Q631 and their periphery circuit, and service it if defective.
When buzz sound can be heard in the vicinity of power circuit.FLOW CHART NO.4
Check if there is any short-circuit on the rectifying diode and the circuit in each rectifying circuit of the secondary side,and service it if defective. (IC631, Q209, Q210, Q211, Q635, Q637, Q640, Q641, Q642, D631, D632, D633, D638, D641, D642, D646, D647)
Check D657, R661 and their periphery circuit, and service it if defective.
AL+33V is not output.FLOW CHART NO.5
Is approximately +35V voltage supplied to thecathode of D638?
No
Yes
Check C638, D638, D639 and their periphery circuit, and service it if defective.
Check IC601, D615, D616, IC602 and their periphery, circuit and service it if defective.
8-2 PL11.0TR
Check Q207, Q208, D205, D207, P-ON-H1 line and their periphery circuit, and service it if defective.
LCD+31.5V is not output.FLOW CHART NO.6
Is approximately +35V voltage supplied to the collector of Q210?
No
Yes
See FLOW CHART No.5<AL+33V is not output>
Replace Q209.
Is approximately +13.5V voltage supplied to thebase of Q209?
Yes
NoCheck Q207, Q208, D203, D204, D211, P-ON-H1 line and their periphery circuit, and service it if defective.
No
LCD+13V is not output.FLOW CHART NO.7
Is approximately +16V voltage supplied to thecollector of Q209?
Yes
Check C631, D631, D635 and their periphery circuit, and service it if defective.
P-ON+7V is not output.FLOW CHART NO.8
Is approximately +7V voltage supplied to thecathode of D646?
Check C644, D646 and their periphery circuit, and service it if defective.
Yes
No
Check for short-circuiting or leak on the load circuit, and service it if defective.
8-3 PL11.0TR
See FLOW CHART No.8 <P-ON+7V is not output.>
See FLOW CHART No.8 <P-ON+7V is not output.>
AL+13V is not output.FLOW CHART NO.11
Yes
NoIs approximately +13V voltage supplied to thecathode of D641 and D642?
Check C639, D641, D642 and their periphery circuit, and service it if defective.
Check for short-circuiting or leak on the load circuit, and service it if defective.
P-ON+5V is not output. (LCD+13V is outputted normally.)FLOW CHART NO.9
Is approximately +6.5V voltage supplied to thecollector of Q641?
Is approximately +6V voltage supplied to the base of Q641?
NoYes
Yes
Check D645 and their periphery circuit, and service it if defective.
No
Replace Q641.
TUNER+5V is not output. (LCD+13V is outputted normally.)FLOW CHART NO.10
Is approximately +6.5V voltage supplied to thecollector of Q640?
Is approximately +6V voltage supplied to the base of Q640?
NoYes
Yes
Check D645 and their periphery circuit, and service it if defective.
No
Replace Q640.
P-ON+3V is not output.FLOW CHART NO.12
Is approximately +3V voltage supplied to thecathode of D647?
Yes
No
Check for short-circuiting or leak on the load circuit, and service it if defective.
Check C645, D647 and their periphery circuit, and service it if defective.
8-4 PL11.0TR
P-ON+3.3V is not output.FLOW CHART NO.13
Is approximately +4.5V voltage supplied to thecathode of D633?
Is the "H" signal (approximately +3.5V) inputted to the base of Q637?
NoYes
Yes
Check C633, D633 and their periphery circuit, andservice it if defective.
Check Q638, Q639, D666, P-ON-H2 line and their periphery circuit, and service it if defective.
No
Replace Q637.
P-ON+9V is not output. (LCD+13V is outputted normally.)FLOW CHART NO.14
Is approximately +13.5V voltage supplied to thecollector of Q642?
Is approximately +10V voltage supplied to thebase of Q642?
Is approximately +5V voltage supplied to Pin(3) of IC631?
NoYes
Yes
Yes
Check D670 and their periphery circuit, and service it if defective.
NoCheck Q635, D659 and their periphery circuit, andservice it if defective.
See FLOW CHART No.5 <AL+33V is not output.>
See FLOW CHART No.11 <AL+13V is not output.> No
No
AL+3.3V is not output.FLOW CHART NO.15
Is approximately +35V voltage supplied to thecollector of Q635?
Yes
Replace IC631.
Replace Q642.
Check C632, D632 and their periphery circuit, and service it if defective.
Check Q207, Q208, D208, D210, P-ON-H1 line and their periphery circuit, and service it if defective.
Replace Q211.
Is approximately -6V voltage supplied to thebase of Q211?
Yes
No
No
LCD-5V is not output.FLOW CHART NO.16
Is approximately -6.5V voltage supplied to theanode of D632?
Yes
8-5 PL11.0TR
[ Video Signal Section ]
No
Is the "L" pulse sent out Pin(1) terminal of remote control receiver (RS101) when the infrared remote control is activated?
Check the line between Pin(1) terminal of remote control receiver(RS101) and Pin(25) of CN301, and service it if defective.
Yes
Is the "L" pulse supplied to Pin(25) of CN301?
Yes
Is 3.3V voltage supplied to Pin(2) terminal of theremote control receiver (RS101)?
No
FLOW CHART NO.2
Operation is possible from the remote control unit.
Check AL+3.3V line and service it if defective.
NoReplace the remote control receiver(RS101) or the remote control unit.
Yes
Replace Digital Main CBA Unit.
When pressing each switches (SW101B, SW103B~SW107B) do the voltage of Pin(29) of CN302 decrease?
Yes
The key operation is not functioning.FLOW CHART NO.1
Are the contact point and installation state of the key switches (SW101B, SW103B~SW107B) normal?
Re-install the switches (SW101B, SW103B~SW107B) correctly or replace the poor switch.
Check the switches (SW101B, SW103B~SW107B) and their periphery, and service it if defective.
Yes
Replace Digital Main CBA Unit.
No
No
No operation is possible from the remote control unit.
Picture does not appear normally.(Video input)FLOW CHART NO.3
Are the video signal inputted to Pin(4) of CN302?
Yes
Check the line between Pin(4) of CN302 and JK752, and service it if defective.
No
Replace Digital Main CBA Unit or LCD ModuleAssembly.
8-6 PL11.0TR
Picture does not appear normally.(S-Video input)FLOW CHART NO.5
Are the video signal outputted to the Pin(6, 8) ofCN302?
Check the line between Pin(6, 8) of CN302 and JK751, and service it if defective.
Check TU301 and their periphery circuit, and service it if defective.
Yes
No
No
Picture does not appear normally.(Tuner input)FLOW CHART NO.4
Are the DIF signal inputted to the Pin(26,28) of CN302?
Yes
Replace Digital Main CBA Unit or LCD ModuleAssembly.
Replace Digital Main CBA Unit or LCD ModuleAssembly.
Pin(6): S-VIDEO-CPin(8): S-VIDEO-Y
Picture does not appear normally.(Y/Pb/Pr input)FLOW CHART NO.6
Are the video signal inputted to the Pin(15, 17, 19) of CN302?
Check the line between Pin(15, 17, 19) of CN302 and input terminals(JK731, JK732, JK733), and service it if defective.
Yes
No
Replace Digital Main CBA Unit or LCD ModuleAssembly.
Pin(15): VIDEO-YPin(17): VIDEO-PbPin(19): VIDEO-Pr
8-7 PL11.0TR
[ Audio Signal Section ]
Check SP801,SP802 and their periphery circuit,and service it if defective.
Are the audio(L/R) signals inputted to the Pin(3, 40)of IC801?
Are the audio(L/R) signals inputted to the Pin(3, 5)of IC871?
Yes
Yes
Audio is not outputted normally.(Audio input)FLOW CHART NO.1
Are the audio(L/R) signals inputted to Pin(2, 15)of IC771?
Check the line between Pin(2, 15) of IC771 andinput terminal(JK753, JK754), and service it if defective.
Yes
No
No
No
Are the audio(L/R) signals outputted to the Pin(1, 2)of CN801 and CN802?
Are the audio(L/R) signals outputted to the audio output terminal?
Check IC801 and their periphery circuit, and service it if defective.
CN801: SP(L) CN802: SP(R)
JK871: AUDIO(L)-OUT JK872: AUDIO(R)-OUT
No
Yes
Are the audio(L/R) signals inputted to each pin of CN301?
Replace Digital Main CBA Unit.
Check the line between Pin(6, 8) of CN301 and Pin(3, 40) of IC801, and service it if defective.
Check the line between Pin(2, 4) of CN301 and Pin(3, 5) of IC871, and service it if defective.
No Check the line between Pin(1, 7) of IC871 and audio output terminal(JK871, JK872), and service it if defective.
Pin(6) :Pin(8) :Pin(2) :Pin(4) :
AMP(L)-OUTAMP(R)-OUTAUDIO(L)-OUTAUDIO(R)-OUT
No
8-8 PL11.0TR
Are the audio(L/R) signals inputted to each pin of CN301?
Replace Digital Main CBA Unit.No
Yes
Audio is not outputted normally.(Component Audio input)FLOW CHART NO.2
Are the audio(L/R) signals inputted to the Pin(4, 11)of IC771?
Check the line between Pin(4, 11) of IC771 andinput terminal(JK741, JK742), and service it if defective.
No
Check SP801,SP802 and their periphery circuit,and service it if defective.
Are the audio(L/R) signals inputted to the Pin(3, 40)of IC801?
Are the audio(L/R) signals inputted to the Pin(3, 5)of IC871?
Yes
Yes
No
No
Are the audio(L/R) signals outputted to the Pin(1, 2)of CN801 and CN802?
Are the audio(L/R) signals outputted to the audio output terminal?
Check IC801 and their periphery circuit, and service it if defective.
CN801: SP(L) CN802: SP(R)
JK871: AUDIO(L)-OUT JK872: AUDIO(R)-OUT
No
Yes
Check the line between Pin(6, 8) of CN301 and Pin(3, 40) of IC801, and service it if defective.
Check the line between Pin(2, 4) of CN301 and Pin(3, 5) of IC871, and service it if defective.
No Check the line between Pin(1, 7) of IC871 and audio output terminal(JK871, JK872), and service it if defective.
Pin(6) :Pin(8) :Pin(2) :Pin(4) :
AMP(L)-OUTAMP(R)-OUTAUDIO(L)-OUTAUDIO(R)-OUT
8-9 PL11.0TR
Yes
Audio is not outputted normally.(Tuner input)FLOW CHART NO.3
Are the DIF signals outputted to the Pin(26, 28)of CN302?
Check TU301 and their periphery circuit, andservice it if defective.
No
Are the audio(L/R) signals inputted to each pin of CN301?
Replace Digital Main CBA Unit.No
Check SP801,SP802 and their periphery circuit,and service it if defective.
Are the audio(L/R) signals inputted to the Pin(3, 40)of IC801?
Are the audio(L/R) signals inputted to the Pin(3, 5)of IC871?
Yes
Yes
No
No
Are the audio(L/R) signals outputted to the Pin(1, 2)of CN801 and CN802?
Are the audio(L/R) signals outputted to the audio output terminal?
Check IC801 and their periphery circuit, and service it if defective.
CN801: SP(L) CN802: SP(R)
JK871: AUDIO(L)-OUT JK872: AUDIO(R)-OUT
No
Yes
Check the line between Pin(6, 8) of CN301 and Pin(3, 40) of IC801, and service it if defective.
Check the line between Pin(2, 4) of CN301 and Pin(3, 5) of IC871, and service it if defective.
No Check the line between Pin(1, 7) of IC871 and audio output terminal(JK871, JK872), and service it if defective.
Pin(6) :Pin(8) :Pin(2) :Pin(4) :
AMP(L)-OUTAMP(R)-OUTAUDIO(L)-OUTAUDIO(R)-OUT
9-1 PL11.0ABLS
AC18
KE
Y S
WIT
CH
IC33
01(M
AIN
MIC
RO
CO
NT
RO
LLE
R)
DIG
ITA
L M
AIN
CB
A U
NIT
IR S
EN
SO
R C
BA
FU
NC
TIO
N C
BA
PO
WE
R S
UP
PLY
CB
A
CL1
02BR
EM
OT
ES
EN
SO
R
RS
101
P-O
N+
9V
PO
WE
RD
101
CL1
03B
CN
302
CN
3702
CN
3702
CN
302
CLK
OU
TC
LKIN
X31
0125
MH
zO
SC
N1
N2
TO
INV
ER
TE
RB
LOC
K
DIA
GR
AM
(CN
1001
)
TO
PO
WE
R S
UP
PLY
B
LOC
K D
IAG
RA
M
PR
OT
EC
T3
AE
5V
CO
M-P
WM
AB18
PR
OT
EC
T2
AD
4P
RO
TE
CT
1A
D5
KE
Y-IN
1AC
5
BA
CK
LIG
HT-
SW
AB16
E1
E2
P-O
N-H
2AB
13R
EM
OT
ER2
2
RE
MO
TE
E3
P-O
N-H
1
PR
OT
EC
T2
PR
OT
EC
T1
P-O
N-H
2P
-ON
-H1
R23
CL1
03A
KE
Y-IN
13
3
CN
201
CN
101
CN
301
CN
3701
AB23
BA
CK
LIG
HT-
AD
J
IC31
01 (
ME
MO
RY
)
SC
K SI
SO
AB25
AB24
AC25
AC24
6 5 2 1E
113
AC19
SC
L
SD
A
CN
301
CN
3701
CS
WP
SC
KS
INS
OU
TC
SW
P
IC20
1,Q
203,
Q20
4,Q
205
DR
IVE
2222
SC
L
2121
SD
A
1111
PR
OT
EC
T1
1515
PR
OT
EC
T2
55
PR
OT
EC
T3
2929
VC
OM
-PW
M
2626
BAC
KLI
GH
T-S
W
2828
BAC
KLI
GH
T-A
DJ
KE
Y-IN
129
29
P-O
N-H
19
9
RE
MO
TE
2525
P-O
N-H
21
1
RE
MO
TE
22
P-O
N+
9V5
5K
EY-
IN1
44
6P
RO
TE
CT
3
5B
ACK
LIG
HT-
SW
4B
ACK
LIG
HT-
AD
J
14V
CO
M
TO A
UD
IOB
LOC
K
DIA
GR
AM
AU
DIO
-MU
TE
INP
UT
0IN
PU
T1
AU
DIO
-MU
TE
INP
UT
0IN
PU
T1
AB9
SC
LS
DA
9 8
TU
301
(TU
NE
R U
NIT
)
SC
LS
DA
4 5
TU
301
(TU
NE
R U
NIT
)
Eit
her
TU
301
is u
sed
for
Po
wer
Su
pp
ly C
BA
.
* *
BLOCK DIAGRAMS[TYPE A]
1. System Control Block Diagram
9-2
2. Video Block Diagram
PL11.0BALV
DIG
ITA
L M
AIN
CB
A U
NIT
CO
MP
ON
EN
T-Y
-IN
CO
MP
ON
EN
T-P
b-IN
CO
MP
ON
EN
T-P
r-IN
JK73
1
JK73
2
JK73
3
VID
EO
-IN
44
S-V
IDE
O-C
-IN
66
S-V
IDE
O-Y
-IN
88
S-V
IDE
O-S
W5
5C
OM
-VID
EO-Y
-IN15
15CO
M-V
IDEO
-Pb-
IN17
17CO
M-V
IDEO
-Pr-I
N19
19
JAC
K C
BA
CL7
01A
C
L701
BV
IDE
O-I
N5
S-V
IDE
O-C
-IN
3S
-VID
EO
-Y-I
N1
5 3 1JK
751
S-V
IDE
O-I
N
CY
JK75
2V
IDE
O-I
N
S-V
IDE
O-S
W-IN
22
PO
WE
R S
UP
PLY
CB
A
CN
302
CN
3702
DIF
-OU
T1
2626
IF-A
GC
2424
DIF
-OU
T2
2828
DIF
-OU
T1
DIF
-OU
T2
IF-A
GC
CN
302
CN
3702
VID
EO
-IN
S-V
IDE
O-C
-IN
S-V
IDE
O-Y
-IN
S-V
IDE
O-S
WC
OM
-VID
EO-Y
-IN
COM
-VID
EO-P
r-IN
COM
-VID
EO-P
b-IN
TO D
IGIT
AL
SIG
NA
L P
RO
CE
SS
BLO
CK
DIA
GR
AM
WF
1W
F2
WF
3
WF
4W
F5
WF
6
VID
EO
SIG
NA
LA
UD
IO S
IGN
AL
Eit
her
TU
301
is u
sed
for
Po
wer
Su
pp
ly C
BA
.
TU
301
DIF
-OU
T1
13D
IF-O
UT
212
(TU
NE
R U
NIT
) IF-A
GC
14
TU
301
DIF
-OU
T1
11D
IF-O
UT
210
(TU
NE
R U
NIT
) IF-A
GC
9
* *
9-3
3. Audio Block Diagram
PL11.0ABLA
IC77
1(A
UD
IO S
ELE
CTO
R)
AU
DIO
(L)-
OU
T
AU
DIO
(R)-
OU
T
HD
MI-
AU
DIO
(L)-
IN
HD
MI-
AU
DIO
(R)-
IN
JK72
1
JK72
2
JK87
1
JK87
2
CO
MP
ON
EN
T-A
UD
IO(L
)-IN
CO
MP
ON
EN
T-A
UD
IO(R
)-IN
JK74
1
JK74
2
2 4 1 5 15 11 12 14
JAC
K C
BA
CL7
01A
CL7
01B
AU
DIO
(L)-
IN7
7A
UD
IO(R
)-IN
99
AU
DIO
(L)
-IN
AU
DIO
(R)
-IN
JK75
3
JK75
4
CN
3702
CN
302
AU
DIO
(L)
1313
AU
DIO
(R)
1111 C
N37
02C
N30
2IN
PU
T1
1010
INP
UT
012
12 CN
3701
CN
301
AU
DIO
(L)-
OU
T2
2A
UD
IO(R
)-O
UT
44
AM
P(L
)-O
UT
66
AM
P(R
)-O
UT
88
PO
WE
R S
UP
PLY
CB
AD
IGIT
AL
MA
IN C
BA
UN
IT
4
IC80
1 (A
UD
IO A
MP
)
3 40
CO
NT
RO
L LO
GIC
CN
801
CL8
01S
P80
1S
PE
AK
ER
L-C
H
CN
802
SP
(R)-
1
CL8
02S
P80
2S
PE
AK
ER
R-C
H
GAI
N CO
NTRO
L
PWM
G
ENER
ATO
R
PWM
G
ENER
ATO
R
CN
302
CN
3702
AU
DIO
-MU
TE
2020
JK84
1D
IGIT
AL
AU
DIO
-OU
T(C
OA
XIA
L)Q
841
Q77
1
Q77
2
BU
FF
ER
Q87
1
Q87
3,Q
874
MU
TE
Q87
2 MU
TE
SP
DIF
22
SP
(R)+
2
SP
(L)-
1S
P(L
)+2
GAI
N CO
NTRO
L
PWM
G
ENER
ATO
R
PWM
G
ENER
ATO
R
Q80
1
CO
NT
RO
L LO
GIC
3
109
13
IC87
1 (O
P A
MP
)
13
75
DR
IVE
IC38
02(D
/A C
ON
VE
RT
ER
)
D/A
CO
NV
ER
TE
R15 14
8 7 6 5
(L-C
H)
(R-C
H)
IC38
01(D
/A C
ON
VE
RT
ER
)
D/A
CO
NV
ER
TE
R15 14
8 7 6 5
(L-C
H)
(R-C
H)
AU
DIO
(L)
AU
DIO
(R)
TO
DIG
ITA
LS
IGN
AL
PR
OC
ES
SB
LOC
KD
IAG
RA
M
TO
DIG
ITA
LS
IGN
AL
PR
OC
ES
SB
LOC
KD
IAG
RA
M
INP
UT
1
LRC
LKB
CLK
AD
ATA
1A
CLK
SP
DIF
AD
ATA
0
INP
UT
0A
UD
IO-M
UT
E
TO
SY
ST
EM
CO
NT
RO
LB
LOC
KD
IAG
RA
M
AU
DIO
SIG
NA
L
WF
7
3437333635
3394402
(AU
DIO
DS
P)
IC38
03 DS
P
8 15 36 28
9-4
4. Digital Signal Process Block Diagram
LVD
S T
X
AD23
AD24
AE23
AF23
AF22
AE22
AD21
AD22
AF24
AE24
W25
W23
Y24
Y23
Y22
TP
PO
LC
PV
OE
ST
V
CN
3902
48 47 46 45 44 43 38 37 36 35 34 33 42 41 63 64 30 31 32
IC39
01 (
TIN
ING
CO
NT
RO
LLE
R)
8 7 10 9 12 11 16 15 14 13
DAT
A
PR
OC
ES
SIN
G
FR
C
LIN
E B
UF
FE
R
GA
MM
A
CO
RR
EC
TOR
LVD
SR
X
LVD
S
OU
TP
UT
DAT
AIN
PU
T
LAT
CH
DIG
ITA
L M
AIN
CB
A U
NIT
IC33
01 (
DIG
ITA
L S
IGN
AL
PR
OC
ES
S)
LCD
MO
DU
LEA
SS
EM
BLY
DIG
ITA
LS
IGN
AL
PR
OC
ES
S
A/D
CO
NV
ER
TER
S-V
IDE
O-Y
-IN
SW
V1
U2
U1
S-V
IDE
O-C
-IN
U3
VID
EO
-IN
V3
CO
M-V
IDE
O-P
r-IN
CO
M-V
IDE
O-P
b-IN
CO
M-V
IDE
O-Y
-IN
AA3
IF-A
GC
HD
MI-
IN1
HD
MI-
IN2
JK37
01
TM
DS
-D0(
+)
TM
DS
-D0(
-)T
MD
S-D
1(+
)T
MD
S-D
1(-)
TM
DS
-D2(
+)
TM
DS
-D2(
-)
SD
AS
CL
7 9 4 6 1 3 10 12 16 15 7 9 4 6 1 3 10 12 16 15
JK37
02
TM
DS
-D0(
+)
TM
DS
-D0(
-)T
MD
S-D
1(+
)T
MD
S-D
1(-)
TM
DS
-D2(
+)
TM
DS
-D2(
-)T
MD
S-C
LOC
K(+
)T
MD
S-C
LOC
K(-
)S
DA
SC
L
A9
B9
C8
C9
B8
A8
B10
A10
A11
B11
A5
B5
C4
C5
B4
A4
B6
A6
A7
B7
TM
DS
-CLO
CK
(+)
TM
DS
-CLO
CK
(-)
DE
MO
DU
LATO
R/M
PE
G D
EC
OD
ER
AE2
AF7
AU
DIO
I/F
TO A
UD
IOB
LOC
K D
IAG
RA
MA
CLK
AD
ATA
1
BC
LKLR
CLK
AD
ATA
0S
PD
IF
AD14
AD9
AD12
AD10
AD11
AC10
DAT
A(0
-15)
AD
DE
SS
(0-1
2)
IC32
01
A13-
15,A
18,
A21-
23,B
13-1
5,B1
7,B1
9-23
C15,
C17-
19,
C23,
C24,
D14,
D15,
D17-
19,
D22,
D23
B1,B
9,C2
,C8,
D1,D
3,D7
,D9,
F1,F
9,G
2,G
8,H1
,H3,
H7,H
9M
2,M
3,M
7,M
8,N2
,N3,
N7,N
8,P2
,P3,
P7,P
8,R2
(DD
R2
SD
RA
M)
HD
MI
I/F
HD
MI-
IN3
7 9 4 6 1 3 10 12 16 15
JK37
04
TM
DS
-D0(
+)
TM
DS
-D0(
-)T
MD
S-D
1(+
)T
MD
S-D
1(-)
TM
DS
-D2(
+)
TM
DS
-D2(
-)T
MD
S-C
LOC
K(+
)T
MD
S-C
LOC
K(-
)S
DA
SC
L
B1
B2
C1
C2
D1
D2
A1
A2
A3
B3
AU
DIO
DE
CO
DE
R
DIF
-OU
T1
DIF
-OU
T2
IF-A
GC
TO V
IDE
OB
LOC
K D
IAG
RA
M
TO V
IDE
OB
LOC
K D
IAG
RA
M
VID
EO
DE
CO
DE
R
AF2
S-V
IDE
O-S
WC
6S
-VID
EO
-SW
M2
AU
DIO
(R)
M1
AU
DIO
(L)
VID
EO
SIG
NA
LA
UD
IO S
IGN
AL
V2
LLV
1(+
)21
LLV
1(-)
20
LLV
0(+
)23
LLV
0(-)
22
LLV
2(+
)19
LLV
2(-)
18LL
V3(
+)
13LL
V3(
-)12
LLV
4(+
)11
LLV
4(-)
10LL
V5(
+)
9LL
V5(
-)8
LLV
CLK
(+)
16LL
VC
LK(-
)15
TP
6P
OL
5C
PV
4O
E1
3S
TV
1
PL11.0ABLD
9-5
5. Inverter Block Diagram
PL11.0ABLINV
INV
ER
TE
R C
BA
CN
1001
P
RO
TE
CT
310
BAC
KLI
GH
T-A
DJ
12V
CO
M2
BA
CK
LIG
HT-
SW
11T
O
SY
ST
EM
CO
NT
RO
LB
LOC
K
DIA
GR
AM
(CN
201)
T19
50
10 11 14 15
2 3 4 5 7 8
14 3
2 Q19
70
(FE
ED
BA
CK
)
(IS
OLA
TO
R)
Q19
71IC19
30
14 3
2
IC19
31
Q19
31
TO
P
OW
ER
SU
PP
LY
BLO
CK
D
IAG
RA
M(C
N60
2)
HO
T
CO
LD
HO
T C
IRC
UIT
. BE
CA
RE
FU
L.
Q19
72
SW
ITC
HIN
GQ
1930
CN
1901
Q19
32
LC
D M
OD
UL
EA
SS
EM
BLY
+B
1
HO
T+
15V
4H
OT-
GN
D3
10C
N10
03V
CO
M
IC12
00(P
WM
CO
NT
RO
L)
BA
CK
LIG
HT
1 2 1 2
CN
1101
CN
1102
BA
CK
LIG
HT
T11
01
Q12
01
Q13
00Q
1303
Q17
00
T11
02
OU
TPU
T
PRO
TEC
T
ST
B DU
TYLO
GIC
PWM
FEED
BAC
K
SWIT
CH
ING
Q17
01
SWIT
CH
ING
Q17
02
SWIT
CH
ING
Q17
03
SWIT
CH
ING
2421
1318
12 167 174 2
Q12
02
Q13
01
T11
00B
AC
KLI
GH
T1 2
CN
1100
4 1 3
7 68 5
2 4 1 3
7 68 5
24 1 3
7 68 5
2
+10
.5V
RE
G.
NO
TE
:T
he v
olta
ge fo
r pa
rts
in h
ot c
ircui
t is
mea
sure
d us
ing
hot G
ND
as
a co
mm
on te
rmin
al.
9-6
6. Power Supply Block Diagram
PL11.0ABLP
HO
TC
OL
DP
OW
ER
SU
PP
LY C
BA
HO
T C
IRC
UIT
. BE
CA
RE
FU
L.
14 3
82
T60
1
TO
INV
ER
TE
RB
LOC
K
DIA
GR
AM
(C
N19
01)
CN
602
3
HO
T-G
ND
2H
OT
+15
V3
+B
1
LIN
EF
ILT
ER
L601
AC
601
AC
CO
RD
BR
IDG
ER
EC
TIF
IER
D60
1- D
604
54
11 12 13 14 16 17 18 1997 8
FE
ED
BA
CK
Q60
1S
WIT
CH
ING
Q63
1,D
653
CN
201
CN
1001
CN
301
CN
3701
Q20
7,Q
208
SW
ITC
HIN
G
Q21
1,D
210
SW
-5V
SW
Q40
1
SW
+13
V
Q63
5IC
631
+3.
3VR
EG
.2
3
Q63
4
Q63
6
Q63
8,Q
639
Q64
1,Q
643
SW
+5V
Q64
0S
W+
5V
Q64
2S
W+
9V
Q63
7,D
666
SW
+3.
3V
LIN
EF
ILT
ER
L602
4A/1
25V
F60
1 4A
/125
V
Q60
2S
WIT
CH
ING
P-O
N-H
1TO
SY
ST
EM
C
ON
TR
OL
BLO
CK
DIA
GR
AM
P-O
N-H
2
+5V
RE
G.
PR
OT
EC
T2
PR
OT
EC
T1
SW
ITC
HIN
G
AL+
33V
P-O
N+
5V
AL+
3.3V
AL+
13V
TU
NE
R+
5V
P-O
N+
9V
19,2
0
47,8
21,2
2
13,1
4
LCD
+13
VLC
D+
5V
VG
HP
-ON
+3.
3V
P-O
N+
3VP
-ON
+7V
AL+
3.3V
P-O
N+
3.3V
P-O
N+
5V
INV
ER
TE
R C
BA
DIG
ITA
L M
AIN
CB
A U
NIT
3LC
D-5
V13
P-O
N+
3.3V
19,2
0
P-O
N+
3.3V
126
VG
H10
LCD
+13
V8,
9
AL+
3.3V
21,2
21610
P-O
N+
7V16
P-O
N+
3V10
P-O
N+
5V13
,14
Q21
0S
W+
31.5
V
Q20
1, Q
202,
Q21
2
Q20
9, Q
213,
D20
4
Q60
3,
Q60
4S
W
HO
T+
15V
IC60
2E
RR
OR
VO
LTA
GE
DE
TS
WIT
CH
ING
C
ON
TR
OL
VH
1Z
CD
5O
UT
4F
B3
IS6
VC
C
IC60
1
15
CA
UT
ION
!F
ixed
vol
tage
(or
Aut
o vo
ltage
sel
ecta
ble)
pow
er s
uppl
y ci
rcui
t is
used
in th
is u
nit.
If M
ain
Fus
e (F
601)
is b
low
n , c
heck
to s
ee th
at a
ll co
mpo
nent
s in
the
pow
er s
uppl
yci
rcui
t are
not
def
ectiv
e be
fore
you
con
nect
the
AC
plu
g to
the
AC
pow
er s
uppl
y.O
ther
wis
e it
may
cau
se s
ome
com
pone
nts
in th
e po
wer
sup
ply
circ
uit t
o fa
il.
For
con
tinue
d pr
otec
tion
agai
nst r
isk
of fi
re,
repl
ace
only
with
sam
e ty
pe 4
A, 1
25V
fuse
.C
AU
TIO
N !
:
AT
TE
NT
ION
: U
tilis
er u
n fu
sibl
e de
rec
hang
e de
mêm
e ty
pe d
e 4
A, 1
25V
.4A
/125
V
NO
TE
:T
he v
olta
ge fo
r pa
rts
in h
ot c
ircui
t is
mea
sure
d us
ing
hot G
ND
as
a co
mm
on te
rmin
al.
9-7 PL11.0BBLS
KE
Y S
WIT
CH
IR S
EN
SO
R C
BA
FU
NC
TIO
N C
BA
PO
WE
R S
UP
PLY
CB
A
CL1
02BR
EM
OT
ES
EN
SO
R
RS
101
P-O
N+
9V
PO
WE
RD
101
CL1
03B
CN
302
CN
302
TO
INV
ER
TE
RB
LOC
K
DIA
GR
AM
(CN
1001
)
TO
PO
WE
R S
UP
PLY
B
LOC
K D
IAG
RA
MP
RO
TE
CT
2P
RO
TE
CT
1
P-O
N-H
2P
-ON
-H1
CL1
03A
KE
Y-IN
13
3
CN
201
CN
101
CN
301
CN
301
IC20
1,Q
203,
Q20
4,Q
205
DR
IVE
2222
SC
L
2121
SD
A
1111
PR
OT
EC
T1
1515
PR
OT
EC
T2
55
PR
OT
EC
T3
2929
VC
OM
-PW
M
2626
BAC
KLI
GH
T-S
W
2828
BAC
KLI
GH
T-A
DJ
KE
Y-IN
129
29
P-O
N-H
19
9
RE
MO
TE
2525
P-O
N-H
21
1
RE
MO
TE
22
P-O
N+
9V5
5K
EY-
IN1
44
6P
RO
TE
CT
3
5B
ACK
LIG
HT-
SW
4B
ACK
LIG
HT-
AD
J
14V
CO
M
SC
LS
DA
9 8
TU
301
(TU
NE
R U
NIT
)
SC
LS
DA
4 5
TU
301
(TU
NE
R U
NIT
)
Eit
her
TU
301
is u
sed
for
Po
wer
Su
pp
ly C
BA
.
* *S
CL
SD
A
TO D
IGIT
AL
SIG
NA
L P
RO
CE
SS
BLO
CK
D
IAG
RA
M
DIG
ITA
L M
AIN
CB
A U
NIT
Q30
06
Q30
05
AL+
3.3V
R12
IC30
05(M
AIN
MIC
RO
CO
NT
RO
LLE
R)
CN
3006
CN
3006
XO
UT
25X
IN25
X30
0125
MH
zO
SC
H15
H16
PR
OT
EC
T3
B13
VC
OM
-PW
MF
2
PR
OT
EC
T2
D13
PR
OT
EC
T1
C13
KE
Y-IN
1A
15
BA
CK
LIG
HT-
SW
E2
G1
D1
P-O
N-H
2B
16
RE
MO
TE
C14
P-O
N-H
1C
1
CN
3002
F3
BA
CK
LIG
HT-
AD
J
IC30
06 (
ME
MO
RY
)
SC
K SI
SO
T11
P11
R11
P12
6 5 2 1
T12
SC
LS
DA
CN
3002
CS
SC
KS
INS
OU
TC
S
TO A
UD
IOB
LOC
K
DIA
GR
AM
AU
DIO
-MU
TE
INP
UT
0IN
PU
T1
AU
DIO
-MU
TE
INP
UT
0IN
PU
T1
E1
[TYPE B]1. System Control Block Diagram
9-8
2. Video Block Diagram
PL11.0BBLV
DIG
ITA
L M
AIN
CB
A U
NIT
CO
MP
ON
EN
T-Y
-IN
CO
MP
ON
EN
T-P
b-IN
CO
MP
ON
EN
T-P
r-IN
JK73
1
JK73
2
JK73
3
VID
EO
-IN
44
S-V
IDE
O-C
-IN
66
S-V
IDE
O-Y
-IN
88
S-V
IDE
O-S
W5
5C
OM
-VID
EO-Y
-IN15
15CO
M-V
IDEO
-Pb-
IN17
17CO
M-V
IDEO
-Pr-I
N19
19
JAC
K C
BA
CL7
01A
C
L701
BV
IDE
O-I
N5
S-V
IDE
O-C
-IN
3S
-VID
EO
-Y-I
N1
5 3 1JK
751
S-V
IDE
O-I
N
CY
JK75
2V
IDE
O-I
N
S-V
IDE
O-S
W-IN
22
PO
WE
R S
UP
PLY
CB
A
CN
302
CN
3006
DIF
-OU
T1
2626
IF-A
GC
2424
DIF
-OU
T2
2828
DIF
-OU
T1
DIF
-OU
T2
IF-A
GC
CN
302
CN
3006
VID
EO
-IN
S-V
IDE
O-C
-IN
S-V
IDE
O-Y
-IN
S-V
IDE
O-S
WC
OM
-VID
EO-Y
-IN
COM
-VID
EO-P
r-IN
COM
-VID
EO-P
b-IN
TO D
IGIT
AL
SIG
NA
L P
RO
CE
SS
BLO
CK
DIA
GR
AM
WF
1W
F2
WF
3
WF
4W
F5
WF
6
VID
EO
SIG
NA
LA
UD
IO S
IGN
AL
Eit
her
TU
301
is u
sed
for
Po
wer
Su
pp
ly C
BA
.
TU
301
DIF
-OU
T1
13D
IF-O
UT
212
(TU
NE
R U
NIT
) IF-A
GC
14
TU
301
DIF
-OU
T1
11D
IF-O
UT
210
(TU
NE
R U
NIT
) IF-A
GC
9
* *
9-9
3. Audio Block Diagram
PL11.0BBLA
IC77
1(A
UD
IO S
ELE
CTO
R)
AU
DIO
(L)-
OU
T
AU
DIO
(R)-
OU
T
HD
MI-
AU
DIO
(L)-
IN
HD
MI-
AU
DIO
(R)-
IN
JK72
1
JK72
2
JK87
1
JK87
2
CO
MP
ON
EN
T-A
UD
IO(L
)-IN
CO
MP
ON
EN
T-A
UD
IO(R
)-IN
JK74
1
JK74
2
2 4 1 5 15 11 12 14
JAC
K C
BA
CL7
01A
CL7
01B
AU
DIO
(L)-
IN7
7A
UD
IO(R
)-IN
99
AU
DIO
(L)
-IN
AU
DIO
(R)
-IN
JK75
3
JK75
4
CN
3006
CN
302
AU
DIO
(L)
1313
AU
DIO
(R)
1111 C
N30
06C
N30
2IN
PU
T1
1010
INP
UT
012
12 CN
3002
CN
301
AU
DIO
(L)-
OU
T2
2A
UD
IO(R
)-O
UT
44
AM
P(L
)-O
UT
66
AM
P(R
)-O
UT
88
PO
WE
R S
UP
PLY
CB
AD
IGIT
AL
MA
IN C
BA
UN
IT
20
IC80
1 (A
UD
IO A
MP
)
1 44
9,10
13,1
4
35,3
631
,32
MU
TE
CO
NT
RO
L
CN
801
CL8
01S
P80
1S
PE
AK
ER
L-C
H
CN
802
SP
(R)-
1
CL8
02S
P80
2S
PE
AK
ER
R-C
H
PW
M1
PW
M2
DR
IVE
1
CN
302
CN
3006
AU
DIO
-MU
TE
2020
JK84
1D
IGIT
AL
AU
DIO
-OU
T(C
OA
XIA
L)Q
841
Q77
1
Q77
2
BU
FF
ER
Q87
1
Q87
3,Q
874
MU
TE
Q87
2 MU
TE
SP
DIF
22
SP
(R)+
2
SP
(L)-
1S
P(L
)+2
Q80
1
CO
NT
RO
L LO
GIC
3
109
13
IC87
1 (O
P A
MP
)
13
75
DR
IVE
2
DR
IVE
AU
DIO
(L)
AU
DIO
(R)
TO D
IGIT
AL
SIG
NA
LP
RO
CE
SS
BLO
CK
DIA
GR
AM
TO D
IGIT
AL
SIG
NA
LP
RO
CE
SS
BLO
CK
DIA
GR
AM
INP
UT
1
SP
DIF
INP
UT
0A
UD
IO-M
UT
E
TO S
YS
TE
MC
ON
TR
OL
BLO
CK
DIA
GR
AM
AU
DIO
SIG
NA
L
WF
7
AU
DIO
(L)-
OU
TA
UD
IO(R
)-O
UT
AM
P(L
)-O
UT
AM
P(R
)-O
UT
9-10
4. Digital Signal Process Block Diagram
DIG
ITA
L M
AIN
CB
A U
NIT
IC30
05 (
DIG
ITA
L S
IGN
AL
PR
OC
ES
S)
IC30
18 (
HD
MI S
W)
IC30
11 (
EE
PR
OM
)
CN
3005
LLV
1(+
)21
LLV
1(-)
20
LLV
0(+
)23
LLV
0(-)
22
LLV
2(+
)19
LLV
2(-)
18LL
V3(
+)
13LL
V3(
-)12
LLV
4(+
)11
LLV
4(-)
10LL
V5(
+)
9LL
V5(
-)8
LLV
CLK
(+)
16LL
VC
LK(-
)15
TP
6P
OL
5C
PV
4O
E1
3S
TV
1
P14
P13
N16
N15
P16
P15
T16
R14
R13
T13
T14
T15
R16
R15
L13
M15
L16
L15
M14
B4
A4
B3
A3
B2
A2
B1
A1
LVD
S T
X
DIG
ITA
LS
IGN
AL
PR
OC
ES
S
A/D
CO
NV
ER
TER
S-V
IDE
O-Y
-IN
SW
D8
B11C9
S-V
IDE
O-C
-IN
A10
C10
VID
EO
-IN
C8
CO
M-V
IDE
O-P
r-IN
CO
M-V
IDE
O-P
b-IN
CO
M-V
IDE
O-Y
-IN
B9
IF-A
GC
HD
MI-
IN1
HD
MI-
IN2
SC
LS
DA
JK30
03
TM
DS
-D0(
+)
TM
DS
-D0(
-)T
MD
S-D
1(+
)T
MD
S-D
1(-)
TM
DS
-D2(
+)
TM
DS
-D2(
-)
HD
MI-
DAT
AH
DM
I-C
LOC
K
742 41 45 44 48 47 39 38 36 37
26 27 23 24 20 21 17 18
57 56 60 59 63 62 54 53 51 52
2 37 6
15 14
10 11
9 4 6 1 3 10 12 16 15 7 9 4 6 1 3 10 12 16 15
JK30
04
TM
DS
-D0(
+)
TM
DS
-D0(
-)T
MD
S-D
1(+
)T
MD
S-D
1(-)
TM
DS
-D2(
+)
TM
DS
-D2(
-)T
MD
S-C
LOC
K(+
)T
MD
S-C
LOC
K(-
)H
DM
I-D
ATA
SD
A1
HD
MI-
CLO
CK
SC
L1
SD
A2
SC
L2S
DA
3S
CL3
SD
A0
SC
L0
HD
MI-
IN3 7 9 4 6 1 3 10 12 16 15
JK30
02
TM
DS
-D0(
+)
TM
DS
-D0(
-)T
MD
S-D
1(+
)T
MD
S-D
1(-)
TM
DS
-D2(
+)
TM
DS
-D2(
-)T
MD
S-C
LOC
K(+
)T
MD
S-C
LOC
K(-
)H
DM
I-D
ATA
HD
MI-
CLO
CK
TM
DS
-CLO
CK
(+)
TM
DS
-CLO
CK
(-)
DE
MO
DU
LATO
R/M
PE
G D
EC
OD
ER
A12
A16
AU
DIO
I/F
TO A
UD
IOB
LOC
K D
IAG
RA
M
AM
P(R
)-O
UT
AM
P(L
)-O
UT
SP
DIF
A7
N10 B7
DAT
A(0
-15)
AD
DR
ES
S(0
-12)
IC30
02
N4,N
7,N8
,P3,
P4,P
6-P8
,R3
,R4,
R6,R
8,T2
-T5
H1,H
2,J1
,J2,
J4,K
1,K3
,L1
,L2,
M1-
M3,
N1
B1,B
9,C2
,C8,
D1,D
3,D7
,D9,
F1,F
9,G
2,G
8,H1
,H3,
H7,H
9M
2,M
3,M
7,M
8,N2
,N3,
N7,N
8,P2
,P3,
P7,P
8,R2
(DD
R2
SD
RA
M)
HD
MI
SW
AU
DIO
DE
CO
DE
R
HD
MI
I/F
DIF
-OU
T1
DIF
-OU
T2
IF-A
GC
TO V
IDE
OB
LOC
K D
IAG
RA
M
VID
EO
DE
CO
DE
R
B12
S-V
IDE
O-S
WN
12S
-VID
EO
-SW
B8
AU
DIO
(R)
A8
AU
DIO
(L)
AU
DIO
(R)-
OU
T
AU
DIO
(L)-
OU
T
A6
B6
VID
EO
SIG
NA
LA
UD
IO S
IGN
AL
TP
PO
LC
PV
OE
ST
V
LC
D M
OD
UL
EA
SS
EM
BLY
8 7 11 10 14 13 5 4 1 2
TO S
YS
TE
M
CO
NT
RO
LB
LOC
K D
IAG
RA
M
PL11.0BBLD
9-11
5. Inverter Block Diagram
PL11.0BBLINV
INV
ER
TE
R C
BA
CN
1001
P
RO
TE
CT
310
BAC
KLI
GH
T-A
DJ
12V
CO
M2
BA
CK
LIG
HT-
SW
11T
O
SY
ST
EM
CO
NT
RO
LB
LOC
K
DIA
GR
AM
(CN
201)
T19
50
10 11 14 15
2 3 4 5 7 8
14 3
2 Q19
70
(FE
ED
BA
CK
)
(IS
OLA
TO
R)
Q19
71IC19
30
14 3
2
IC19
31
Q19
31
TO
P
OW
ER
SU
PP
LY
BLO
CK
D
IAG
RA
M(C
N60
2)
HO
T
CO
LD
HO
T C
IRC
UIT
. BE
CA
RE
FU
L.
Q19
72
SW
ITC
HIN
GQ
1930
CN
1901
Q19
32
LC
D M
OD
UL
EA
SS
EM
BLY
+B
1
HO
T+
15V
4H
OT-
GN
D3
10C
N10
03V
CO
M
IC12
00(P
WM
CO
NT
RO
L)
BA
CK
LIG
HT
1 2 1 2
CN
1101
CN
1102
BA
CK
LIG
HT
T11
01
Q12
01
Q13
00Q
1303
Q17
00
T11
02
OU
TPU
T
PRO
TEC
T
ST
B DU
TYLO
GIC
PWM
FEED
BAC
K
SWIT
CH
ING
Q17
01
SWIT
CH
ING
Q17
02
SWIT
CH
ING
Q17
03
SWIT
CH
ING
2421
1318
12 167 174 2
Q12
02
Q13
01
T11
00B
AC
KLI
GH
T1 2
CN
1100
4 1 3
7 68 5
2 4 1 3
7 68 5
24 1 3
7 68 5
2
+10
.5V
RE
G.
NO
TE
:T
he v
olta
ge fo
r pa
rts
in h
ot c
ircui
t is
mea
sure
d us
ing
hot G
ND
as
a co
mm
on te
rmin
al.
9-12
6. Power Supply Block Diagram
PL11.0BBLP
HO
TC
OL
DP
OW
ER
SU
PP
LY C
BA
HO
T C
IRC
UIT
. BE
CA
RE
FU
L.
14 3
82
T60
1
TO
INV
ER
TE
RB
LOC
K
DIA
GR
AM
(C
N19
01)
CN
602
3
HO
T-G
ND
2H
OT
+15
V3
+B
1
LIN
EF
ILT
ER
L601
AC
601
AC
CO
RD
BR
IDG
ER
EC
TIF
IER
D60
1- D
604
54
11 12 13 14 16 17 18 1997 8
FE
ED
BA
CK
Q60
1S
WIT
CH
ING
Q63
1,D
653
CN
201
CN
1001
CN
301
CN
3002
Q20
7,Q
208
SW
ITC
HIN
G
Q21
1,D
210
SW
-5V
SW
Q40
1
SW
+13
V
Q63
5IC
631
+3.
3VR
EG
.2
3
Q63
4
Q63
6
Q63
8,Q
639
Q64
1,Q
643
SW
+5V
Q64
0S
W+
5V
Q64
2S
W+
9V
Q63
7,D
666
SW
+3.
3V
LIN
EF
ILT
ER
L602
4A/1
25V
F60
1 4A
/125
V
Q60
2S
WIT
CH
ING
P-O
N-H
1TO
SY
ST
EM
C
ON
TR
OL
BLO
CK
DIA
GR
AM
P-O
N-H
2
+5V
RE
G.
PR
OT
EC
T2
PR
OT
EC
T1
SW
ITC
HIN
G
AL+
33V
P-O
N+
5V
AL+
3.3V
AL+
13V
TU
NE
R+
5V
P-O
N+
9V
19,2
0
47,8
21,2
2
13,1
4
LCD
+13
VLC
D+
5V
VG
HP
-ON
+3.
3V
P-O
N+
3VP
-ON
+7V
AL+
3.3V
P-O
N+
3.3V
P-O
N+
5V
INV
ER
TE
R C
BA
DIG
ITA
L M
AIN
CB
A U
NIT
3LC
D-5
V13
P-O
N+
3.3V
19,2
0
P-O
N+
3.3V
126
VG
H10
LCD
+13
V8,
9
AL+
3.3V
21,2
21610
P-O
N+
7V16
P-O
N+
3V10
P-O
N+
5V13
,14
Q21
0S
W+
31.5
V
Q20
1, Q
202,
Q21
2
Q20
9, Q
213,
D20
4
Q60
3,
Q60
4S
W
HO
T+
15V
IC60
2E
RR
OR
VO
LTA
GE
DE
TS
WIT
CH
ING
C
ON
TR
OL
VH
1Z
CD
5O
UT
4F
B3
IS6
VC
C
IC60
1
15
CA
UT
ION
!F
ixed
vol
tage
(or
Aut
o vo
ltage
sel
ecta
ble)
pow
er s
uppl
y ci
rcui
t is
used
in th
is u
nit.
If M
ain
Fus
e (F
601)
is b
low
n , c
heck
to s
ee th
at a
ll co
mpo
nent
s in
the
pow
er s
uppl
yci
rcui
t are
not
def
ectiv
e be
fore
you
con
nect
the
AC
plu
g to
the
AC
pow
er s
uppl
y.O
ther
wis
e it
may
cau
se s
ome
com
pone
nts
in th
e po
wer
sup
ply
circ
uit t
o fa
il.
For
con
tinue
d pr
otec
tion
agai
nst r
isk
of fi
re,
repl
ace
only
with
sam
e ty
pe 4
A, 1
25V
fuse
.C
AU
TIO
N !
:
AT
TE
NT
ION
: U
tilis
er u
n fu
sibl
e de
rec
hang
e de
mêm
e ty
pe d
e 4
A, 1
25V
.4A
/125
V
NO
TE
:T
he v
olta
ge fo
r pa
rts
in h
ot c
ircui
t is
mea
sure
d us
ing
hot G
ND
as
a co
mm
on te
rmin
al.
10-1 PL11.0SC
SCHEMATIC DIAGRAMS / CBA AND TEST POINTS
Standard Notes
WARNING
Many electrical and mechanical parts in this chassis have special characteristics. These characteristics often pass unnoticed and the protection afforded by them cannot necessarily be obtained by using replacement components rated for higher voltage, wattage, etc. Replacement parts that have these special safety characteristics are identified in this manual and its supplements; electrical components having such features are identified by the mark “#” in the schematic diagram and the parts list. Before replacing any of these components, read the parts list in this manual carefully. The use of substitute replacement parts that do not have the same safety characteristics as specified in the parts list may create shock, fire, or other hazards.
Notes:1. Do not use the part number shown on these
drawings for ordering. The correct part number is shown in the parts list, and may be slightly different or amended since these drawings were prepared.
2. All resistance values are indicated in ohms (K = 103, M = 106).
3. Resistor wattages are 1/4W or 1/6W unless otherwise specified.
4. All capacitance values are indicated in µF (P = 10-6 µF).
5. All voltages are DC voltages unless otherwise specified.
6. This schematic diagrams are masterized version that should cover the entire PL11.0 chassis models.Thus some parts in detail illustrated on this schematic diagrams may vary depend on the model within the PL11.0 chassis.Please refer to the parts lists for each models.
7. The Circuit Board layout illustrated on this service manual is the latest version for this chassis at the moment of making this service manual. Depend on the mass production date of each model, the actual layout of each Board may differ slightly from this version.
10-2 PL11.0SC
LIST OF CAUTION, NOTES, AND SYMBOLS USED IN THE SCHEMATIC DIAGRAMS ON THE FOLLOWING PAGES:
1. CAUTION:CAUTION: FOR CONTINUED PROTECTION AGAINST RISK OF FIRE, REPLACE ONLY WITH SAME TYPE_A,_V FUSE.
ATTENTION: UTILISER UN FUSIBLE DE RECHANGE DE MÊME TYPE DE_A,_V.
2. CAUTION: Fixed Voltage (or Auto voltage selectable) power supply circuit is used in this unit. If Main Fuse (F601) is blown, first check to see that all components in the power supply circuit are not defective before you connect the AC plug to the AC power supply. Otherwise it may cause some components in the power supply circuit to fail.
3. Note:1. Do not use the part number shown on the drawings for ordering. The correct part number is shown in the
parts list, and may be slightly different or amended since the drawings were prepared.
2. To maintain original function and reliability of repaired units, use only original replacement parts which are listed with their part numbers in the parts list section of the service manual.
4. Voltage indications on the schematics are as shown below: Plug the TV power cord into a standard AC outlet.:
5. How to read converged lines
6. Test Point Information
2 315.0 5.0
Voltage Indicates that the voltage is not consistent here.
Power on mode(Unit: Volt)
3
2
1
A B C D
1-B1
1-D3
AREA D3
AREA B1
1-D3
Distinction AreaLine Number (1 to 3 digits)
Examples:1. "1-D3" means that line number "1" goes to the line number "1" of the area "D3". 2. "1-B1" means that line number "1" goes to the line number "1" of the area "B1".
: Indicates a test point with a jumper wire across a hole in the PCB.
: Used to indicate a test point with a component lead on foil side.
: Used to indicate a test point with no test pin.
: Used to indicate a test point with a test pin.
The reference number of parts on Schematic Diagrams/CBA can be retrieved by application search function.
10-3
KTC3198-GR-AT/P
Q603
4
3 2
1
IC601TLP781F
330P/2KV
C607
1000P/250VC691
2HOT-GND
CN6021+B
BEADBC601
1500P/100V
C606
SB2150BDD631
2SC2120-YQ209
C2210.01
D203
SB360BHD646
FR104-BD643
0.1C682
1500P/2KVC637
FR154D638
KTA1267-GR-AT/PQ207
KTC3198-Y-AT/PQ208
2SA950-OQ636
FR154D661
KTC3198-Y-AT/P
Q631
FR154D662
KTC3199-GR-AT/PQ634
WIRED648
2200P/100VC646
D208
KTC3198-Y-AT/P
Q211
2SC4881FQ637
FR104-BD632
C651OPEN
KTC3199-GR-AT/P
Q639
KTA1267-GR-AT/PQ638
FR151-B/PD633
SB390D642
OPENC641
KTC3198-Y-AT/PQ642
D410
KTC3198-Y-AT/PQ402
KTC3198-Y-AT/P
Q401
D411
OPENC692
D404
2SC2120-YQ635
5V6BSA-T26D659
6V2BSB-T26D644
1ZB43BBD639
3V3BSB-T26D658
6V2BSB-T26D210
10BSB-T26D670
10BSB-T26D407
24BSB-T26D635
5V6BSB-T26D652
2.7KR229
10R687
1R651
51KR410
11KR232
47KR240
39KR639
22KR404
820R663
1KR648
220R243
OPENR406
22KR241
3.6KR679
12KR242
750R233
2.2KR234
3.9/1/2W
R227
22KR225
22KR673
3.3KR637
3.3kR223
10KR680
10KR675
30KR411
1.2KR689
WIRER638
180R646
47KR659
OPENR666
1.5KR644
47KR403
47KR676
2.7KR649
22KR407
270R677
2.7KR228
2.7MR607
0.47/2W
R613
2.7MR604
1KR674
820R664
24KR652
OPENR694
10R678
WIRER672
47KR405
1.5KR231
15R662
22KR226
27KR224
1000/6.3VC652
220/10VC654
220/50VC638
470/25VC222
10/50VC224
2200/6.3VC633
1000/35VC639
100/16VC656
22/50VC657
1000/25VC631
1/50VC642
3300/16VC644
D666KIA431-AT/P
D204KIA431-AT/P
2.2/5WR603
0.22/300VC602
4A/125VF601
OPENC603
SURGEABSORBER
SA601
OPENC604
AC CORDAC601
0.22/300VC601
2.2/5WR605
1N5406-BUD602
JS603
OPEN
L601LINE FILTER
1N5406-BUD603
JS604
OPEN
JS602
OPEN
1N5406-BUD601
L602LINEFILTER
JS601
OPEN
2.7M/1/2WR601
1N5406-BUD604
OPENR602
470/200V
C605
OPENC694
1000P/250VC693
SB390D641
WIRER653
10KR658
10KR654
WIRER665
OPENR645
OPEND649
10R688
WIRED671
D40910KR408
2200/6.3VC645
SB140D647
D421
D419
390/1/2W
R661
OPENC647
33BSB-T26D657 D412
2.7/1WR696
2.7/1WR697
WIRER667
OPENR695
OPENC402
WIRED665
22KR401
22KR402
39BSB-T26D209
D211
OPENQ501
4.7/1/2W
R247OPENR501
OPENC501
2SC2120-YQ641
OPENR692
OPENR691
OPENR693
22R685
D645KIA431B-AT/P
1.1KR641
10KR642
10KR643
1KR686
OPENC655
2.7R682
2.7R683
2SC2120-YQ640
220/10VC653
D415
KTC3198-Y-AT/PQ210
330R235
10R236
24BSC-T26D205
D206
1.5KR238
OPENR239
8.2KR237
D207
AL+33VTUNER+5V
P-ON+3.3V
LCD+31.5VLCD-5V
INV+13VLCD+13V
AUDIO(L)-OUTAUDIO(R)-OUT
AMP(L)-OUTAMP(R)-OUT
28 BACKLIGHT-ADJ27 NU
12 GND
15 PROTECT2
25 REMOTE
4 AUDIO(R)-OUT
20 P-ON+3.3V
2 AUDIO(L)-OUT
14 P-ON+5V
CN3011 P-ON-H2
11 PROTECT1
3 GND
29 VCOM-PWM
10 P-ON+3V
26 BACKLIGHT-SW
18 GND
13 P-ON+5V
9 P-ON-H1
23 GND
6 AMP(L)-OUT
22 AL+3.3V
17 GND16 P-ON+7V
19 P-ON+3.3V
21 AL+3.3V
24 OE2
5 PROTECT3
7 GND8 AMP(R)-OUT
BACKLIGHT-SW
P-ON-H1OE2
BACKLIGHT-ADJVCOM-PWM
PROTECT3
AL+3.3VP-ON+9V
P-ON+3.3V
RESET
AL+3.3V
P-ON+9VP-ON+5V
AL+13V
REMOTE
0.1C684
D4130.1C681
D414
D420
3V9BSB-T26D417
D405
10KR412
15BSB-T26D4068.2K
R245
1N4005D655
220/25VC632
4A 125V
LCD-P-SAFETY
CN6012AC120V1AC120V
2.2/50VC676
OPEND651
OPENR244
OPEND403
OPENC225
OPEND674
OPENR681
OPEND667
3.9/1/2W
R636
820R660
WIRED676
OPEND637
OPENR698
OPENR246
OPEND201
OPENR254
JS201OPEN
2SA950-OQ213
8.2/1WR250
6.8/1/2WR253
D401
27KR655
10KR668
D653KIA431-AT/PF5
0.022/100VC650WIRED654
2.7KR650
JS630
3.9/1/2W
R635
1C643
4V7BSB-T26D664100/10V
C6480.1C649
D660
1R657
OPEND673
1/50VC640
JS631OPEN
OPENR502
3V9BSB-T26D418
0.1C683
OPENR700
OPENR699
1ZB200-YBBD621
3HOT+15V
47KR606
4.7KR611
180R609
10R610
FR103-B/PD617
OPEND611
BEADBC602
BEADBC603
GD S
KHB1D0N60D-RTFQ602
TK5A50DQ601
SD
G
0.1C611
27BSB-T26D609OPEN
R620
OPENR621
1.2KR622
1000P/100V
C60827BSB-T26D608
0.022C614
33PC613
100KR617
3300PC615
68R612
39BSB-T26D615
10KR623
10KR624
11BSB-T26
D607
FR103-B/PD614
FR103-B/PD622
47/50VC609
D619 15KR626
FR104-BD613
FR104-BD612
WIRER618
WIRER619
KTA1267-GR-AT/P
Q604OPENR627
OPEND606
OPENR625
OPEND620
P-ON-H1PROTECT1
OPENR690
100/50V
C610
D610
22/50VC223
5
6
7
81
4
3
2
IC602FA5571-ND1-TE1
ZCD
GND OUT
VCC
NU
VH
IS
FB
2SA950-OQ643
9
8
7
5
4
11
12
13
14
15
16
17
18
193
POWER TRANST601
1 2 3
MM3123DPREIC631
VIN
VOUT
GND
OPEND650
OPEND416
WIRED621A
1ZB200-YBBD621B
0D607A
0D652A
0D659A
D423
100R409
10/50VC403
2.2/2WR701
2.2/2WR702
1000PC608A
1500PC606A
27BSB-T26D616
100/10VC658
0.022C650A
2200PC646A
2
1
3
4
A B C D E F
POWER SUPPLY CBA
ERRORVOLTAGE DET
(SWITCHING)
SWITCHINGCONTROL
HOT COLD
HOT CIRCUIT. BE CAREFUL.
159.4
0.1
2.8
0
0.7
0.6
00
16.2 12.9
13.5
(SWITCHING)
35.2
34.4
0.1
35.1
0.7
0
35.1
34.1
5.5
0 (SWITCHING)
6.1
00.7
(+3.3V REG.)
34.1
(SWITCHING)
(SW+9V)
9.013.4
9.7
5.36.8
6.5
(SWITCHING)
2.5-0.5
0
(FEED BACK)
(SW+13V)
(RESET) (SW-5V)
(SW+3.3V)
(+5V REG.)
35.2
5.5
5.5
4.6
3.4
4.1
-6.0
-6.7
-6.6
-2.0
0
4.4
6.9
6.1
6.8
(SWITCHING)
TO INVERTERCBA CN1901
(SW+13V)
(SW+5V)(SW+5V)
UNLESS OTHERWISE SPECIFIED:DIODES ARE 1SS133.
CONTINUEPOWER 2
CONTINUEPOWER 4
CONTINUEPOWER 4
CONTINUEPOWER 2
TO DIGITAL MAINCBA UNIT CN3701 or CN3002
CONTINUEPOWER 4
CONTINUEPOWER 3
CONTINUEPOWER 2
CONTINUEPOWER 4
(SW+31.5V)
34.5 31.231.6
0
0.20.7
6.0
6.7 5.3
6.0
6.5 5.3
3.7
5.26.0
0 3.35.2
0.8
3.32.60
2.63.32.60
2.63.23.12.50
5.35.30.36.900
3.3
3.30
0.63.33.2
1.1
3.33.3
(NO CONNECTION)
(SWITCHING)
SWITCHIGCONTROL
0
0.1
0.6
1.0 155.3
15.2
3.3
(SWITCHING)
SW HOT+15V
124.9
0.1
15.2
15.2 15.2
14.5
16.8 13.2
16.2 (SWITCHING)
(SWITCHING)
(SWITCHING)
PL11.0SCP1
Power Supply 1 Schematic Diagram
NOTE:The voltage for parts in hot circuit is measured usinghot GND as a common terminal.
CAUTION !Fixed voltage (or Auto voltage selectable) power supply circuit is used in this unit.If Main Fuse (F601) is blown , check to see that all components in the power supplycircuit are not defective before you connect the AC plug to the AC power supply.Otherwise it may cause some components in the power supply circuit to fail.
For continued protection against risk of fire, replace only with same type 4 A, 125V fuse.
CAUTION ! :
ATTENTION : Utiliser un fusible de rechange de même type de 4A, 125V.4A/125V
10-4
AL+3.3V
1/50VC306
SP802SPEAKERR-CH
47PC311
TU301 TUNER UNIT
12
DIF-
OUT2
13
DIF-
OUT1
14
IF-A
GC
15
VCC
16
NU
17
NU
18
NU
19
NU
1
NU
2
NU
3
NU
4
VCC
5
NU
6
+32V
7
GND
8
SDA
11
NU
9
SCL
10
NU
0R310
BC805BEAD
0.47C836
220PC835
OPENR311
47PC307
330/10V
C303
20BSB-T26D804
AUDIO-MUTE
33uHL803
2SP(L)+
0.1C309
OPEND302
WIREL301
470PC846
OPENC301
33uHL801
0.22uHL302
0.47C806
1/50VC815
0.1C305
22KR802
0.47C820
SDA
BC803BEAD
AL+13V
CN8011SP(L)-
10KR818
10KR817
OPEND303
BC802BEAD
0.1C302
0.22uHL303
OPEND301
470PC845
CN8021SP(R)-
33uHL804
0R303
20BSB-T26D802
47PC308
OPENR803
OPENR304
SCL
KTC3198-Y-AT/P
Q801
AMP(R)-OUT0.47C834
33uHL802
220PC837
AL+33V
JS301OPEN
47KR814
0R302
47PC310
47KR816
1/50VC801
0.1C818
DIF-OUT1
20BSB-T26D801
1C828
SP801SPEAKERL-CH
82R308
22KR813
4.7KR809
OPENC304
0R306
IF-AGC
TU301 TUNER UNIT
1
NU
2
NU
3
NU
4
SCL
5
SDA
6
+32V
7
+5V
8
NU
11
DIF-
OUT1
9
IF-A
GC
10
DIF-
OUT2
22KR819
BC804BEAD
AMP(L)-OUT
470PC838
470PC839
JS302
TUNER+5V
DIF-OUT2JS303
OPENR305BC301
WIRE
20BSB-T26D803
0R307
82R309
OPENR301
22KR815
2SP(R)+
0.1C809
OPENR808
1000PC822
47KR820
OPENC832
0R807
0R810
10/50VC819
0R801
1C814
P-ON-H1
1KR647
0.47C803
OPENC811
0.47C810
10/50VC831
0R812
0R811
OPENC830
1C829
0.47C824
10/50VC8161C817
47KR894
PROTECT1
0.1C821
0.1C825
1000PC826
10/50VC827
1000/25VC823 OPEN
D807
1000PC808
0.1C807
0.1C804
1000PC805
OPEND806
OPENR805
OPENR804
313242 3839 35 3340 36 3441 37
3 187 11 152 17 216 10 141 165 209 134 198 12
2529 222428 2327 2630
AVCC
GAINCONTROL
ATT
GAINCONTROL
PWMGENERATOR
OSC
VREF
HBA2 NU NU
HBB2 NU NU
RREF
CONTROLLOGIC
GND
NU HBA1
NU NU HBB1
NU VD DVDD
PWMGENERATOR
PWMGENERATOR
PWMGENERATOR
IC801R2A15124FP
CONTINUEPOWER 1
CONTINUEPOWER 3
0
0.1
2.5
0
3.2
15.5
5.5
2
2.9
POWER SUPPLY CBA
2.5
(AUDIO AMP)
0
CL801
K
*Either TU301 is used for Power Supply CBA.*
L
*
0
(AUDIO-MUTE)
13.5
J
2.5
CL802
I
2.3
H
4.8
G
2.59.9
4
CONTINUEPOWER 1
3CONTINUEPOWER 1
0 0 0 0 0
000002.5 4.9 5.7 15.0 13.515.0 5.7
14.913.5 14.913.55.6 5.6 13.510.0
PL11.0SCP2
Power Supply 2 Schematic Diagram
10-5
JK733
JK732
JK731
JK742
JK741
JK751
YC
SW
JK754
JK752
JK753
39PC731
OPENC752
OPENC751
39PC733
OPENC753
39PC732
75R751
75R753
0R757
10R734
10R735
75R731
15KR743
39KR746
15KR744
39KR761
10R736
0R758
75R732
39KR762
39KR745
15KR760
75R733
0R756
75R752
15KR759
10KR775
KTC3198-Y-AT/PQ772
10KR774
10KR772
10KR773
13
VEE
VDD1
152
14
16
3
6
5
11
4
7
12
10
8 9GND
INH
SWCTL
IC771TC4052BF(ELNF)
KTC3198-Y-AT/PQ771
100PC776
100KR779
100KR777
100KR776
100PC775
WIRER771
0.1C772
39KR725
OPENR713
39KR726
15KR723
JK721
JK722
OPENR714
15KR724
JK711
OPENR716
OPENR715
0R842
1C841
JK841 220R844
110R843
100R846
1C842
0.01C843
10/50VC844
KTC3198-Y-AT/PQ841
2 SPDIF
5 S-VIDEO-SW
AUDIO-MUTEKEY-IN1
BEADBC841
100KR778
OPENR795
OPENR791
OPENR790
OPENR794
OPENR789
OPENR793
OPENR788
OPENR792
OPENR780
OPENR784
OPENR781
OPENR785
OPENR782
OPENR786
OPENR783
OPENR787
100/16VC771
10KR763
4.7KR847
4.7KR848
OPENR711
OPENC701
OPENC703
OPENR712
OPENC702
OPENC704
2.2C723
2.2C724
2.2C743
2.2C744
0C734
0C735
0C736
0C754
0C755
CL701B1 S-VIDEO-Y-IN
CL701A1
2 S-VIDEO-SW 233 S-VIDEO-C-IN
0C756
4 GND
6 GND
8 GND
4
6
8
5 VIDEO-IN 5
7
9
2.2C757
2.2C758
7 AUDIO(L)-IN
9 AUDIO(R)-IN
DIF-OUT1
SCL
DIF-OUT2
AUDIO-MUTE
SDAIF-AGC
P-ON+5VRESET
P-ON+9VP-ON+3.3V
CN3021 GND
3 GND4 VIDEO-IN
6 S-VIDEO-C-IN7 GND8 S-VIDEO-Y-IN9 GND10 INPUT111 AUDIO(R)12 INPUT013 AUDIO(L)14 GND15 COM-VIDEO-Y-IN16 GND17 COM-VIDEO-Pb-IN18 GND19 COM-VIDEO-Pr-IN20 AUDIO-MUTE21 SDA22 SCL23 RESET24 IF-AGC25 GND26 DIF-OUT127 GND28 DIF-OUT229 KEY-IN1
WF2
WF7
WF5
WF1
WF4
WF3
WF6
OPENC773
OPENR845
OPENR841
OPENR721
OPENR722
OPENR741
OPENR742
OPENC721
OPENC722
OPENC741
OPENC742
OPENC761
OPENC762
OPENR754
OPENR755
COMPONENT-Y-IN
COMPONENT-Pb-IN
COMPONENT-Pr-IN
COMPONENT-AUDIO(L)-IN
COMPONENT-AUDIO(R)-IN
AUDIO(L)-IN
AUDIO(R)-IN
VIDEO-IN
S-VIDEO-IN
TO DIGITAL MAINCBA UNIT CN3702 or CN3006
(INVERTER)
0.7
0.2
0
(INVERTER)
0.2
4.5
9.0
9.0
0
0
4.5 0.2
0
0
0.2
0
0
4.5
9.0
0
4.5
HDMI-AUDIO(L)-IN
HDMI-AUDIO(R)-IN
DIGITALAUDIO-OUT(COAXIAL)
(BUFFER)
POWER SUPPLY CBA
PC-AUDIO-IN
5.3
2.0
2.6
QPONM
4
3
1
2
R
2.3
2.3
JACK CBA
CONTINUEPOWER 2
CONTINUEPOWER 1
CONTINUEPOWER 4
(AUDIO SELECTOR)
3.4
0
0
0
0
0
0
0
0
0
3.3
0
0
00
4.5
4.5
1.0
0
3.3
0
1.7
0.2
3.3
3.3
0
0
0
3.3
PL11.0SCP3
Power Supply 3 & Jack Schematic Diagram
10-6
GND
VCCIC871NJM4558M(TE2)
1 2 3 4
5678
33KR891
47PC875
16KR879
2.2C884
100R881
100KR885
100KR883
47PC876
33KR892
16KR880
2.2C885
100R882
100KR886
100KR884 1000P
C878
1000PC877
0.1C879
100/16VC880
1KC882
1KC883
WIREL871
2.2C874
100KR874
JK872
3300PC872
0R875
0R876
560R872
100KR873
560R871
JK871
3300PC871
KTA1267-GR-AT/P
Q874
1KR888
22KR887
2.2C873
1KR877
1KR878
KTC3198-Y-AT/PQ872
KTC3198-Y-AT/PQ871
KTC3198-Y-AT/PQ873
22KR893
1000PC216
OPENC214
10KR218
OPENC212
1C218
0.1C217
100KR213
0.1C201
KTC3198-Y-AT/PQ205
10KR216
OPENC213
10R210
OPENC215
KTC3198-Y-AT/PQ203
1 2 3 4
5678VCC
VEE
IC201TL3472CDR
1R208
Q204KTA1267-GR-AT/P
15KR219
10R212
1KR220
47/25VC219
1.5KR2170
R214
0R211
VCOM 14
5BACKLIGHT-SW4BACKLIGHT-ADJ
LCD+13V 9
GND 76PROTECT3
P-ON+3.3V 12GND 11VGH 10
CN201GND 1
3GND
LCD-5V 13
GND 15
INV+13V(NU) 2
LCD+13V 8
22/25VC210
0R209
KTC3198-Y-AT/PQ202
D2021SS133
1KR206
560R204
100KR207
OPENR203
100KR201
0.1C207
1KR202
Q201KTA1267-GR-AT/P
OPENC208
OPENC209
OPENR205
2.2/50VC204
KTC3198-Y-AT/PQ212
10KR248
CN1011GND
4KEY-IN13AL+3.3V2REMOTE
5P-ON+9V
LCD+31.5VLCD-5V
INV+13VLCD+13V
P-ON+3.3V
AUDIO(L)-OUTAUDIO(R)-OUT
BACKLIGHT-SW
P-ON-H1
BACKLIGHT-ADJVCOM-PWM
PROTECT3
REMOTE
AL+3.3VP-ON+9V
KEY-IN1AUDIO-MUTE
OPENC206
OPENR215
JS203OPEN
OPENR221
LCD-P-SAFETY
OPENC220
OPENR222
OPENQ206
OPENR249
JS202
D675OPEN
0.1C202
OPENC675
0.1C203
JS633
OPENR821
OE2
0R896
XWVUTS
4
3
1
2
POWER SUPPLY CBA
0
(OP AMP)
(MUTE DRIVE)
(AUDIO-MUTE)
(SWITCHING)
(V-COM DRIVE)
(COMPARATOR)
(V-COM DRIVE)
(V-COM DRIVE)
TO INVERTER CBA CN1001
(SWITCHING)
(SWITCHING)
CONTINUEPOWER 1
CONTINUEPOWER 1
CONTINUEPOWER 1
CONTINUEPOWER 1
CONTINUEPOWER 3
AUDIO(L)-OUT
AUDIO(R)-OUT
(SWITCHING)
(AUDIO-MUTE)
0
-2.3
0
5.3
3.4
30.4
31.2
0.4
5.3
0.4
0.3
0
5.4
-2.3
25.7
0
1.0
0
3.4
3.4
3.6
0
29.0
5.4
0.1
-2.3
12.9
0.4
0
0
0
4.5
0.2
4.5
0.2
5.3
4.5
5.35.5
4.5
4.5
12.9
0 0
4.5
9.0
TO IR SENSOR CBA CL102B
PL11.0SCP4
Power Supply 4 Schematic Diagram
10-7
T1102INVERTER TRANS
2
1
4
3 5
6
7
8
Q1702TK50P04M1
G
D
S 39KR1112
10R1222
13R1117
100R1216
2
5V6BSB-T26D1300
0R1214
100KR1510
D1507DAN202U
0.022C1705
100R1131
47KR1301
10R1223
10P/6.3KVC1108
2.2KR1126
2.2KR1102
1000PC1704
2.2C1102
2.2KR1135
0.1C1303
2.2C1101
D1503DAN202U
0.47C1209
KTC3875S-Y-RTK/PQ1202
0.47C1208
T1100INVERTER TRANS
2
1
4
3 5
6
7
8
1000PC1703
5V6BSB-T26D1301
510/2WR1305
1MR1513
100KR1506
D170315BSB-T26
0R1125
D1702
10P/6.3KVC1104
1000PC1707
JS1200
0.1C1300
1000PC1706
OPENQ1204
10KR1703
0.01C1500
OPENC1200
0.1C1201
CN11001
D1508DAN202U
D1700
0.47C1210
CN11021
D1501DAN202U
10/50VC1206
D1706
39KR1514
330PC1107
4.7/1WR1709
100KR15121MR1500
CN11011
100KR1508
D170715BSB-T26
OPENR1226
75KR1204
OPENR1147
130KR1202
22KR1310
2.2C1116
1000PC1207
2.2C1100
D170515BSB-T26
1C1702
330PC1118
6800PC1202
22KR1208
2
OPENR1150
D1506DAN202U
2
2.2KR1123
8.2KR1203
2SA1576UBTLQQ1303
0R1113
470R1118
OPENR1225
100KR1502
1000PC1301
100KR1505
100R1707
D1505DAN202U
10P/6.3KVC1110
2.2C111710P/6.3KVC1106
470R1106
0R1101
100R1107
OPENR1220
10KR1708
13R1129
470R1130
0.47C1212
10KR1215
2.2KR1114
2.2KR1111
2SA1576UBTLQQ1300
100KR1504
4.7KR1209
100KR1511
OPENR1146
10KR1309
13R1105
Q1701TK50P04M1
G
D
S
10P/6.3KVC1114
D1202
T1101INVERTER TRANS
2
1
4
3 5
6
7
8
39KR1124
330PC1123
0.022C1708
330PC1119
4.7/1WR1704
10KR1206
OPENR1145
330PC1113
Q1700TK50P04M1
G
D
S
330PC1109
330PC1105
Q1203OPEN
13R1132
330PC1122
2200/35VC1700
39KR1109
0R1229
560KR1205
1KR1307
100KR1507
13R1108
39KR1121
D1200
68KR1200
D1201
D1504DAN202U
0.01C1213
10/50VC1302
4.7KR1308
100R1116
10P/6.3KVC1112
KTC3875S-Y-RTK/PQ1201
2.2C1205
4.7KR1304
68KR1201
0R1134
OPENR1228
470R1115
39KR1133
10KR1701
1R1221
0R1122
OPENC1214
470R1127
OPENR1227
100R1128
OPENC1502
100KR1503
D1502DAN202U
330PC1111
OPENR1148
100R1700
100R1104
100KR1501
10KR1306
D170115BSB-T26
51KR1302
1000PC1311
2.2C1103
100R1702
13R1120
10KR1706
330PC1115
1000PC1501
D1203
D1500DAN202U
10KR1300
OPENC1211
D1704
330PC1120
27KR1515
0R1516
330PC1121
33KR1207
Q1703TK50P04M1
G
D
S
100KR1509
100R1119
39KR1100
100R1705
KTC3875S-Y-RTK/P
Q1301
4.7KR1213
0R1110
4.7KR1303
OPENR1143
10KR1212
470R1103
6800PC1203
0.1C1204
1
2
3
4
5
6
7
9
10
8
11
12 13
14
24
23
21
18
19
22
17
20
15
16
VCC
STB
GND
DUTY
OSC
OUTPUT
LOGIC
PWM
REG
VLO
PROTECT
FEEDBACK
IC1200BD9244AFV
INV+13V(NU) 14
OPENR1987
GND 5
22KR1972
2SC2120-OQ1932
680P/2KV
C1930
5V6BSB-T26D1931
VCOM 2
OPEND1960
120R1933
13GND
OPENC1906
0.47/50VC1982
270/200V
C1910
CN1001GND 15
120R1932
4HOT+15V
120R1934
3.9KR1967 20K
R1977
82KR1938
1.5KR1982
220R1970
1ZB30BBD1994
OPENR1951
1KR1988
WIREBC1301
47KR1931
47R1930
27BSB-T26D1930
GD
S
TK7A50DQ1930
10PROTECT3
P-ON+3.3V 4
0.1C1933
GND 1
2200/35V
C1993
CN1003GND 1
GND 9
LCD-5V 3
VCOM 10
1800PC1931
GND 5
CN19011+B
OPENC1983
3HOT-GND
0.01C1981
150KR1949
1.5KR1935
BC1930BEAD
0.056/100V
C1932
4
3 2
1
IC1930TLP781F
LCD+13V 3
33BSB-T26D1971
OPENC1934
VGH 6
2NU
D1973
2.2KR1939
D1932
P-ON+3.3V 6
KTC3875S-Y-RTK/PQ1972
P-ON+3.3V 7
0.39/2WR1937
11BACKLIGHT-SW
OPENR1952
8
7
3
4
2
14
10
11
5
15
T1950POWER TRANS
OPENR1950
LCD+13V 2
BC1931BEAD
D1933
0R1981
2200PC1970
180R1936
KTC3198-Y-AT/PQ1931
3.3KR1973
5V6BSB-T26D1970
LCD+13V 7
OPEND1961
VGH 4
LCD+13V 8
SB3150BHD1990
12BACKLIGHT-ADJ
GND 11
KTC3875S-Y-RTK/PQ1971
OPEND1972
1KR1986
GND 9
1ZB36BBD1934
4
3 2
1IC1931TLP781F
LCD-5V 8
1000P/250VC1905
820P/2KVC1990
KTC3875S-Y-RTK/PQ1970
220/35VC1304
0.1C1305
J1001OPEN
J1002
J1091OPEN
OPENR1939A
OPENR1931A
OPENR1930A
OPENR1935A
OPENR1936A
2+B
CN19001GND
OPENR1967A
SB3150BHD1991
SB3150BHD1992
2200/35V
C1994
J1037OPEN
J1044OPEN
J1027OPEN
OPENR1970A
OPENC1935
OPENC1936
OPENC1937
OPENC1938
OPENC1939
OPENR1942
OPENR1941
OPENR1940
OPENR1933AOPENR1934A
OPENR1932A
180R19806.8KR1979
2200/35VC1701
0.1
(SW+10.5V)10.6
00.7
0
LCDMODULEASSEMBLY
0
(SWITCHING)
3.3
11.0(SWITCHING)
0
BACKLIGHT
BACKLIGHT
0
8.0
1.0
BACKLIGHT
10.6
5.1
0
(SWITCHING)
8.6
(PWM CONTROL)
17.0
0
(SWITCHING)
0.2
(SWITCHING)
(SWITCHING)
(SWITCHING)
(SWITCHING)
3.1
1.0
27.0
25.1
20.5
10.6
4.0
1.5
0
0
3.1
7.6
27.0
25.1
20.6
2.2
1.2
0.8
1.3
0.6
0
0
(SWITCHING)
0
20.5
0.7
20.5
24.8
23.8
0
20.9
0.7
20.9
23.8
25.2
0
7.65.1
6.0
(ISOLATOR)
12.9
HOT
0
1
1.1
0
(SWITCHING)
12.9
TO POWER SUPPLY CBA CN602
12.1
4
5.6
3 0.4
00.2
0.4
2
3.4
(SWITCHING)
E
0.2
0
22.5
TO POWER SUPPLY CBA CN201
6.3
UNLESS OTHERWISE SPECIFIED:DIODES ARE 1SS133.
-5.1
G
6.0
A
0
0
0
22.5
D
(FEEDBACK)
C
HOT CIRCUIT. BE CAREFUL.
3.4
5.30
INVERTER CBA
TO LCD MODULEASSEMBLY
F
163.6
0
0
5.9
1.1(SWITCHING)
0.2
(SWITCHING)
23.6
3.3
29.0
(SWITCHING)
0
COLD
B
0
(SWITCHING)
(NO CONNECTION)
(SWITCHING)
PL11.0SCINV
Inverter Schematic Diagram
NOTE:The voltage for parts in hot circuit is measured usinghot GND as a common terminal.
10-8
CL103B1AL+3.3V2GND3KEY-IN1
OPENSW101A
OPENSW103A
OPENSW104A
OPENSW105A
OPENSW106A
OPENSW107A
0.1C108
4.7KR113
8.2KR114
220R108
2.7KR112
10KR109
18KR115
4.7KR111
OPEND107
OPENR152
OPENR151
OPENC151
OPEND151
OPENSW153
OPENR154
OPENSW151
OPENSW152
OPENR153
SW154 SW155
OPENR156
OPENR155
SKQSABSW101B
SKQSABSW104B
SKQSABSW103B
SKQSABSW105B
SKQSABSW107B
SKQSABSW106B
2
1
A B C
FUNCTION CBA
TO IR SENSORCBA CL103A
UNLESS OTHERWISE SPECIFIED:SWITCHES ARE SKHHLMA0100.
OPENOPEN
VOLDOWN
POWER CHDOWN
MENU VOLUP
CH UP
PL11.0SCF
Function Schematic Diagram
10-9
100R101
4KEY-IN1
CL102B1GND
2 GND
47/16VC101
CL103A1 AL+3.3V
OPENC102
1KR106
2REMOTE
5P-ON+9V
Vcc
GND
VOUT
2 31
RS101KSM-712TH2E
3.3KR102
3 KEY-IN1
9.1KR103
330PC1033AL+3.3V
SLR343WBCT3XMD101
0.1C104
OPEND109 OPEN
D108
4 KEY-IN2
IR SENSOR CBA
POWER
(REMOTE SENSOR)
A
TO FUNCTIONCBA CL103B
B
2
C
1
TO POWER SUPPLYCBA CN101
PL11.0SCIR
IR Sensor Schematic Diagram
10-10
100R3931
1 STV
3 OE1
6 TP
4 CPV5 POL
2 XA0
CN390224 GND
13 LLV3(+)
10 LLV4(-)
15 LLVCLK(-)16 LLVCNK(+)
12 LLV3(-)
19 LLV2(+)
11 LLV4(+)
18 LLV2(-)
23 LLV0(+)
20 LLV1(-)21 LLV1(+)22 LLV0(-)
4SDA
2BUS-OPEN
CN39031+3.3V
3GND
5SCL
L3907 EXC24CG900U
L3906 EXC24CG900U
L3905 EXC24CG900U
17 GNDL3904 EXC24CG900U
14 GNDL3903 EXC24CG900U
L3901 EXC24CG900U
9 LLV5(+)8 LLV5(-)
L3902 EXC24CG900U
7 GND
1KR3920
P-ON+3.3V
100R3933
100R3932 1
C3904
OPENR3919
1C3921
100R3930
100R3929
100R3928
100R3927
1C3924
0.1C3927
1C3911
1C3912
22KR3916
0R3902
0R391722R391522R3914
1C3910
22R3913
22R3909
OPENR3912
2.2KR3935
2.2KR3936
10KR3934
0L3908
1.1KR3901
OPENR3921
OPENR3951
10C3902
OPENR3938OPENR3926OPENR3925OPENR3924
OPENR3937
VCOM-PWM
OPENR3922OPENR3923OPENR3911OPENR3918OPENR3908OPENR3910
OPENC3901
OPENR3906OPENR3907OPENR3903OPENR3905
STVOECPVTPPOL
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
21 22 24 25 26 27 28 2923 30 31 32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49505152535455565758596061626364
20191817
SERIALINTERFACE
CONTROL SIGNAL GENERATOR
LVDSRX
LVDSOUTPUT
LVDS RX
DATAINPUTLATCH
DATA PROCESSING
GAMMA CORRECTORFRCLINE BUFFER
IC3901BU9069KUT
NU
NU
VDD-REG
GND
GND
VDDM
GND
VDDPGND
VDDIONU
PWMI
PWMONUGND
GNDNUOE2
TEST
VDDL
VDDL
12 LLV3(-)
1 STV
20 LLV1(-)21 LLV1(+)
17 GND
11 LLV4(+)
3 OE14 CPV
15 LLVCLK(-)
22 LLV0(-)
13 LLV3(+)
18 LLV2(-)
7 GND
19 LLV2(+)
8 LLV5(-)
24 GND
5 POL
16 LLVCNK(+)
9 LLV5(+)
2 XA0
6 TP
10 LLV4(-)
23 LLV0(+)
14 GND
25 GND26 GND27 LCD+12V
OE2
28 LCD+12V29 LCD+12V
CN390431 LCD+12V30 LCD+12V
OPENR3904
Q3751OPEN
1 2 3 4
5678
IC3752OPEN
OPENR3838
OPENR3800
OPENC3786
OPENR3798
OPENR3799
0R3947
OPEN
R3954
100K
R3953
OPEN
R3950
OPEN
R3952
OPEN
R3955
100K
R3956
220P
C3917
220P
C3916
220P
C3918
220P
C3919
OPEN
C3920
0R39460R3945
0R39490R3948
BACKLIGHT-ADJBACKLIGHT-ADJ(1)LCD+12V(1)
OPENC3766
10KR3957
1
2
3
4 5
6
7
8
IC4202AT24C16BN-SH-T
A0
A1
A2
GND SDA
SCL
WP
VCC
10KR3958
CN410420GND19LVDS3(+)18LVDS3(-)17GND16LVDSCE(+)15LVDSCE(-)14GND13LVDS2(+)12LVDS2(-)11GND10LVDS1(+)9LVDS1(-)8GND7LVDS0(+)6LVDS0(-)5GND4GND3GND2+3.3V1+3.3V
AF22
AF18AF20
AD22
AD15
AF21
AF16
AE23
AE20
AD21
AE21
AE16
AE18
AD16AE15
AF17
AF15
AE22
AF19
AE24
*1IC3301(1/5)ZR39775HGCF
AD17AD18
AF23
AE17
AE19
AD24AD23
AF24
AB23BACKLIGHT-ADJ
AD19NUAD20NU
AC23VCOM-PWM
OPENR3939
0R41170R41180R41150R4116
0R41140R4113
0R41110R4112
0R41090R4110
DIGITAL SIGNAL PROCESS/MAIN MICRO CONTROLLER
TO LCD MODULEASSEMBLY
LVDSTX
TO DIGITAL MAIN 2IC3301(2/5)
4
1
3
2
DC FA B E
CONTINUEDIGITAL 5
DIGITAL MAIN CBA UNIT
(NO CONNECTION)
CONTINUEDIGITAL 2
TIMINGCOTROLLER
(MEMORY)
(NO CONNECTION)
(NO CONNECTION)
PL11.0SCDA1
Digital Main 1 Schematic Diagram [TYPE A]
The order of pins shown in this diagram is different from that of actual IC3301. IC3301 is divided into five and shown as IC3301 (1/5) ~ IC3301 (5/5) in this Digital Main Schematic Diagram Section.
1 NOTE:
10-11
1
2
3
4
5
14
13
12
11
15
6
7
8
9
10
JK3703
OPEND-SUB CONNECTOR
GND7
COM-VIDEO-Y-IN15
GND1
GND9S-VIDEO-Y-IN8
SPDIF2
RESET23
AUDIO-MUTE20
CN3702KEY-IN129
GND25
S-VIDEO-C-IN6
COM-VIDEO-Pr-IN19
GND16COM-VIDEO-Pb-IN17
VIDEO-IN4
33PC3725
33PC3726
33PC3727
33PC3732
33PC3733
33PC3735
1000PC3736
OPENC3714
100R3703
100PC3737
AF4
IC3301(2/5)ZR39775HGCF
*1
NU U3V3
AA3
V4NUU5NU
AB3NU
U2U1
V1
T4
V2
T2T1T3
*AGND
T5VGA-VSYNC
R5VGA-HSYNC
0.1C3020 22R30220.1C3021 22R3021
0.1C3022 22R3023
0.22C3034 10R30310.22C3035 10R3032
0.22C3036 10R3033
OPENC3042 OPENR3030
4700PC3037 0R3026
OPENC3039
OPENR3034
OPENR3027
OPENR3035
OPENC3049
OPENC3048
OPENC3040
OPENC3050
OPENC3041
OPENR3036
DIF-OUT228
DIF-OUT126
IF-AGC24
AUDIO(R)11INPUT012
SCL22SDA21
AUDIO(L)13
33PC3729
SDASCLRESET
AUDIO-MUTE
AE4 NU
AD3 NU
AE1 NU
AF2AE2
W22 OE2
AF7 IF-AGC
OPENC3038
OPENC3044
100R3718
0.1C3014
0.1C3009
2.2KR3007
100PC3006
33PC3045
33PC3046
33PC3047
OPENR3029
OPENR3028
AB11VGA-SCL
AE9VGA-SDA
U4NU
V5NU
AB4NUAA4NU
AA1VREF(+)AA2VREF(-)
4.7C3517
AB1NU0.47C3516
L4NU62KR3501
W3GNDL5GNDK5GNDM5GNDN5GND
SPDIF
GND3
S-VIDEO-SW5
1000PC3741
100R3717
INPUT110
33PC3728
100R3719
100R3737AUDIO(R)
100R3735AUDIO(L)
GND14
GND18
100R3722
100R3724100R3723
33PC3739
33PC3738
100R3720
GND27
KEY-IN1
AL+3.3VP-ON+3.3V
OPENR3750
100R3102
D10 GPIO-P1
100R3101
4.7KR3104
4.7KR31064.7KR3111
C11 RESET-LCD
4.7KR3108
C12 GPIO-P2
C10 GPIO-P0
0.1C3013
L30020.22uH
15PC3002
15PC3003
33PC3004
0R3002
0R3004
3.9KR3001
AD2 NU0.1C3005
AD1 NU0.1C3007
AF1 NU0.1C3008
AD8 NUAC7 NUAC8 GPIO0AC6 NUAE7 NU
4.7KR3005
AF8 NU
AA5 NU
D11 GPIO-P4D12 NUE12 NU
100R3109E11 WP
4.7R3107
WP
AB20 NU4.7KR3118
4.7KR3137
AB19 GPIO-P9AB18 VCOM-PWMAB17 NU
U22 NUY22 STVY23 OEY24 CPVY25 NUY26 NUW25 TPW24 NUW23 POLV23 NUV22 NUV24 NU
C6 S-VIDEO-SW
U24 NU4.7KR31464.7KR3157
D5 NU
U23 NUR23 P-ON-H1AB13 P-ON-H2
P-ON-H1P-ON-H2
AB14 NUAB16 BACKLIGHT-SW
BACKLIGHT-SW
OPENR3161AC14 VCOM-PWM
VCOM-PWM
E1 INPUT0E2 INPUT1E3 REMOTE
REMOTE
E4 NUE5 NUF1 LED1F2 USB-ENF3 NU
LED1
USB-EN
F4 NUF5 NU
G3NUG4NUH3NUAA6NUK22NU
100R3721
1000PC3740
100PC3730
100R3160
SCLSDA
100PC3734
VCOM-PWM
OPENR3140
OPENR3158
GPIO1
L3004OPEN
OPENC3060
OPENC3059
R3006OPEN OPENR3044
33R3142
STV
33R3143
OE
33R3144
CPV
33R3145
TP
33R3141
POL
GND 2
CN3101GPIO-P2 1
D3703OPEN
D3706OPEN
P-ON+5V
OPENR3003
100PC3731
OPENR3738
OPENR3736
R3733OPEN
R3732OPEN
0R3836
1
2
3 4
VCC
GND
5
IC3001OPEN
R3747OPEN
R3748OPEN
RESET-DSP
OPENR3749
OPENR3746
L3701OPEN
OPENC3063
OPENR303833R4108
OE2
OPENC3058
OPENR3046
OPENC3057
OPENR3045OPENC3064
OPENR3037
L3702OPEN
OPENC3024
OPENC3026
OPENC3025
W2NUW1NU
Y2NUY1NU
OPENR3751
Q3704OPEN
OE2
4
JI
3
2
L
1
G H K
DIGITAL MAIN CBA UNIT
TO POWER SUPPLY CBA CN302
DIGITAL SIGNAL PROCESS/MAIN MICRO CONTROLLER
*A:B24,F6,J10~J18,K9~K18,L9~L18, M9~M18,N9~N18,P9~P18,R9~R18, R25,T9~T18,U9~U18,V9~V18,V25, AE25
CONTINUEDIGITAL 4
CONTINUEDIGITAL 3
CONTINUEDIGITAL 4
SW
A/DCONVERTER
DEMODULATOR/MPEGDECODER
DIGITALSIGNALPROCESS
TO DIGITAL MAIN 4IC3301(4/5)
TO DIGITAL MAIN 1IC3301(1/5)
CONTINUEDIGITAL 5
CONTINUEDIGITAL 5
CONTINUEDIGITAL 3
TO DIGITAL MAIN 3IC3301(3/5)
CONTINUEDIGITAL 1
(NO CONNECTION)
CONTINUEDIGITAL 3
CONTINUEDIGITAL 5
(BUFFER)
PL11.0SCDA2
Digital Main 2 Schematic Diagram [TYPE A]
The order of pins shown in this diagram is different from that of actual IC3301. IC3301 is divided into five and shown as IC3301 (1/5) ~ IC3301 (5/5) in this Digital Main Schematic Diagram Section.
1 NOTE:
10-12
AD10ACLK
1 2 3 4 5 6 7 9 108 11 12 13 15 1614 17 18 19 20
2130 28 2729 26 2540 39 24 23 2238 37 36 34 3335 32 31
IC3803BU9414FV-E2
ADDR
MODE
VSS2
PLLFIL
NUNUVDD
ANATEST
LDOPOFF
REG15
DVDDCORE
VSS1
SDAI
SCLI
MUTEX-DAC
MUTEX-SP
RESETX
SDATA2
SDATA1
LRCKI
NUBCKI
MCLK
VSS3
SYSCLKO
BCKO
LRCKO
DATAO1
DATAO2
RESETOX
MUTEXSPO
SCLO
SDAO NU NU NU NU NU NU
SPDIFO
1.5KR3815
0.027C3811 2700P
C3810
100R3816
100R3817 0
R3818
OPENC3809
2.2C3808
SDASCL
1 2 3 4 5 6 7
910
8
1112131516 14GND VCC NUNU
ENHANCEDMULTI-LEVELDELTA-SIGMAMODULATOR
ZERO DETECT
4X/8XOVERSAMPLINGDIGITAL FILTER/FUNCTIONCONTROLLER
LPFLPF DAC
DAC
AUDIOSERIAL PORT
SYSTEMCLOCKMANAGER
SERIALCONTROL PORT
IC3801PCM1782DBQR
1 2 3 4 5 6 7
910
8
1112131516 14GND VCC NUNU
ENHANCEDMULTI-LEVELDELTA-SIGMAMODULATOR
ZERO DETECT
4X/8XOVERSAMPLINGDIGITAL FILTER/FUNCTIONCONTROLLER
LPFLPF DAC
DAC
AUDIOSERIAL PORT
SYSTEMCLOCKMANAGER
SERIALCONTROL PORT
IC3802PCM1782DBQR
100R3801
OPENR3813
100R3802
OPENR3811
AD9BCLKAD12LRCLKAC10AD14
100PC3812
100PC3813
33R382833R382933R383033R383133R3832
AE14NU
AF12AF11AF10AF9AD11
10C3054AE8NU
0.1C3015
AE12NU10C3053
0.1C3016
10C3052
0.1C3017AE13NU
AF13GND
M1
*1IC3301(3/5)ZR39775HGCF
10C3055
AUDIO(L)
M210C3056
AUDIO(R)
L1L2K1NUK2NUJ1NUJ2NUH1NUH2NUK3NUJ3NUAC9NU
10KR3041
AD13NU10KR3042
AF14NU10KR3043
SPDIF
OPENR3810
100R3809 100
R3805
OPENR3812
10KR3819
100R3808
OPENR3814
AUDIO(L)-OUT
47KR3806
47KR3807
AUDIO(R)-OUT
10C3805
0.1C3806
10C3804
BC3802BK1608HS601-T
10C3801
0.1C3803
BC3801BK1608HS601-T
P-ON+5V
10C3802
47KR3804
AMP(L)-OUTAMP(R)-OUT
10C3807
0R3835
0R3834
P-ON+5V
OPENR3824OPENR3825OPENR3826OPENR3827
100PC3814100PC3815100PC3816
4 EJTDO
9 VSS
7 RESET
2 TRSTN
8 RESET
3 ADATA1
CN41011 VDD
6 EJTCK5 EJTMS
TRSTN0R4101
JTDI-TOPENR3152
JTDO-TOPENR3151
JTDI-M100R3154
JTDO-M100R3153
JTMS100R3149
EJTCK
RESET
0R3820
0R3821
0R3823
47KR3803 0
R3822
47R4102
100R3940
RESET-DSP
OPENR3833P-ON-H1
OPENC3817
1000PC3023
OPENC3818
OPENC3819
4.7KR3164
P-ON+3.3V
1KR4104
1KR4103
1KR4105
OPEN
R4107
4.7K
R4106
BC3803BC1608HS601-T
4
PO
3
2
R
1
M N Q
DIGITAL SIGNAL PROCESS/MAIN MICRO CONTROLLER
AUDIO D/ACONVERTER
AUDIO D/ACONVERTER
AUDIOI/F
AUDIO D/ACONVERTER
CONTINUEDIGITAL 5
CONTINUEDIGITAL 2
DIGITAL MAIN CBA UNIT CONTINUEDIGITAL 5
CONTINUEDIGITAL 2
TO DIGITAL MAIN 2IC3301(2/5)
TO DIGITAL MAIN 4IC3301(4/5)
(NO CONNECTION)
CONTINUEDIGITAL 4
CONTINUEDIGITAL 2
Digital Main 3 Schematic Diagram [TYPE A]
PL11.0SCDA3
The order of pins shown in this diagram is different from that of actual IC3301. IC3301 is divided into five and shown as IC3301 (1/5) ~ IC3301 (5/5) in this Digital Main Schematic Diagram Section.
1 NOTE:
10-13
A9
47KR3729
A11
A10
B4
A8
B5
C9
C4
C3HDMI0-REXT
B8
47KR3728
B9
10KR3725
C7HDMI1-5VSENSE
A7B7
OPENR3742
EDZTE61D3702
A6
D8HDMI0-CEC
1KR3779
EDZTE61D3701
0.1C3744
A5
C8
390R3731
E17EJTCK
10KR3773
D9HDMI-HPD
A4
D3NU
0.1C3742
47KR3730
C5
B10
D4HDMI2-HPD
47KR3727
B6
D7HDMI0-5VSENSE
D6HDMI1-HPD
10KR3726
IC3201K4T51163QG-HCF7
*A VDDJ2VREF
E2 NU
K2CKEJ8CKK8CKL8NUK7RASL7CASK3WEL1BA2/NUL3BA1L2BA0R2A12P7A11M2A10/APP3A9P8A8P2A7N7A6N3A5N8A4N2A3M7A2M3A1M8A0K9ODT
*BVSS
A2 NUR8 NUR7 NUR3 NU
B7 UDQSA8 UDQS/NUB3 UDMB9 DQ15B1 DQ14D9 DQ13D1 DQ12D3 DQ11D7 DQ10C2 DQ9C8 DQ8F7 LDQSE8 LDQS/NUF3 LDMF9 DQ7F1 DQ6H9 DQ5H1 DQ4H3 DQ3H7 DQ2G2 DQ1G8 DQ0
A21 S0-DQ14A14 S0-DQ13B22 S0-DQ12B20 S0-DQ11B17 S0-DQ10B21 S0-DQ9A15 S0-DQ8B14 S0-DQ7A22 S0-DQ6B13 S0-DQ5A23 S0-DQ4B19 S0-DQ3A18 S0-DQ2B23 S0-DQ1A13 S0-DQ0
A20 S0-UDMA19 S0-LDM
A24 S0-VREF
A16 S0-UDQSNB16 S0-UDQSB18 S0-LDQSNA17 S0-LDQSD16 S0-RASNC16 S0-CASND20 S0-WENB12 S0-CKNA12 S0-CKC21 S0-CKEC13 S0-ODTC14 NUC24 S0-A12
C22 S0-BA2
D19 S0-A1
C15 S0-A4
C17 S0-A2
D14 S0-A8D18 S0-A9
D23 S0-A7
C20 S0-BA1
C18 S0-A11
D17 S0-A6
D15 SO-A0
C23 S0-A3
D22 S0-A10
D21 S0-BA0
C19 S0-A5
B26 NU
*B NU
A25 NUA26 NU
59R340559R3404
100R3401
100R3402
0.1C3419
N22NU
M22RXD0P22NU
R22REMOTE
L22TXD0
E13NU
AD7 GPIO1
E16TRSTN
AB26 SPI-HOLD
OPENR3114
18 VCC
10 TMDS-CLOCK(+)
2 D-SHIELD0
8 D-SHIELD2
15 SCL
17 GND
19 HOT-PLUG-DETECT
7 TMDS-D0(+)
11 C-SHIELD0
JK37011 TMDS-D2(+)
4 TMDS-D1(+)
6 TMDS-D1(-)
12 TMDS-CLOCK(-)
3 TMDS-D2(-)
13 CEC
16 SDA
9 TMDS-D0(-)
14 NU
5 D-SHIELD1
18 VCC
10 TMDS-CLOCK(+)
2 D-SHIELD0
8 D-SHIELD2
15 SCL
17 GND
19 HOT-PLUG-DETECT
7 TMDS-D0(+)
11 C-SHIELD0
JK37021 TMDS-D2(+)
4 TMDS-D1(+)
6 TMDS-D1(-)
12 TMDS-CLOCK(-)
3 TMDS-D2(-)
13 CEC
16 SDA
9 TMDS-D0(-)
14 NU
5 D-SHIELD1
B11 Q37032SK3018
27KR3734 D3704
RB751S-40TE61
82KR3781
1KR3778
0.1C3745
10KR3772
0.1C3743
A2
2 D-SHIELD0
A3
EDZTE61D3707
17 GND
C2
D2
10KR3771
E6HDMI1-5VSENSE11 C-SHIELD010 TMDS-CLOCK(+)
47KR3740
3 TMDS-D2(-)
10KR3739
0.1C3747
47KR3741
0.1C3746
16 SDA
8 D-SHIELD2A1
D1
4 TMDS-D1(+)
JK37041 TMDS-D2(+)
12 TMDS-CLOCK(-)13 CEC
18 VCC
B2
14 NU
B3
15 SCL
6 TMDS-D1(-)5 D-SHIELD1
1KR3780
19 HOT-PLUG-DETECT
9 TMDS-D0(-)
7 TMDS-D0(+)
B1
C1
OPENR3410
0.1C3402
0.1C3401
10C3421
0.1C3420
100R3403
0L3401
L25S1-DQ114.7KR3407
4.7KR3408
L26S1-UDM
IC3301(4/5)ZR39775HGCF
*1
B15 SO-DQ15
100R3116E14JTDI-TE18JTDO-TE15JTMS
E19JTDI-M100R3117
B25JTDO-M
4.7KR3115D13NU
100R3119100R3120
4.7KR3124
REMOTE
AF26NUAE26NUAD26NUAD25NUAF3CLKIN-SEL
4.7KR3113U26NU
U25NU
N1 CLKINN2 CLKOUT
X310125MHz 1M
R312712PC3108
12PC3109
330R3128
AB21 MOR-RESET-N-OUT
150R3406
100R3138
AC12 USB(+)AB12 USB(-)
4.7KR3139
AB22 MOR-RESET-N
W26 RESET100R3123
RESET
0.033C3116
AL+3.3V
P-ON+5V
0.1C4101
1
2
3
4 5
6
7
8
IC3101W25X32VSSIGE
CS
SO
WP
GND SI
SCK
NU
VCC100R31674.7KR3125
AC26 SPI-SEL14.7KR3126
100R3168100R3166100R3169100R3135
AC22 I2C-MORPH-ENA
WP4.7KR313310KR3129
AC21 TV-I2C-D10KR3132
AC20 TV-I2C-CAC19 SDAAC18 SCL
SCLSDA
AC16 I2C0-CAC17 I2C0-D
4.7KR31314.7KR3130
1.8KR3122
1.8KR3121
3USB(+)4GND
2USB(-)
CN37041USB+5V
1C3750 Q3701
2SB1732TL
330R3763
330R3762
10KR3760
1C3724
1KR3770
10KR3764
15KR3765
PROTECT5-USB
IC3701AS431AKTR-E1 33K
R3768
33KR3767
180R3769
2.4R3715
1.6R376656P
C375415KR3774
15KR3775
56PC3753
Q37022SC4081UBTLQ
USB-EN10KR3761
0.01C3101
33KR3105 D3101
1SS400 4.7KR3162
DDR+1.8V
P-ON+3.3VP-ON+1.8V
0.1C4102
IC3103PST8420UR
2VDD
4OUT
3CD
1GND
AC25 SOUTAB24 SIN
AB25 SCKAC24 CS
GPIO1
TRSTNJTDI-TJTDO-TJTDI-MJTDO-MJTMSEJTCK
RESET
CN31021I2C0-C2GND3I2C0-D
0.1C3107
4GND
2UARTSUB-TX
CN41031USB+5V
3UARTSUB-RX
D3103 OPENPROTECT1PROTECT3
D3102 OPENPROTECT2
OPENR3171
Q3101OPEN
OPENC3115
OPENR3148
0.1C34030.1C34040.1C34050.1C34060.1C34070.1C34080.1C34090.1C34100.1C34110.1C34120.1C34130.1C34140.1C34150.1C34160.1C34170.1C3418
OPENC3752
0R3409
4.7KR3165
3 UART0-RX4 GND
2 UART0-TX
CN41021 P-ON+5V
10KR3159
OPENL3402
DIGITAL MAIN CBA UNITHDMI-CONNECTOR-1
HDMI-CONNECTOR-2
(BUFFER)
DIGITAL SIGNAL PROCESS/MAIN MICRO CONTROLLER
3
2
4
1
S T U V W X
(DDR2 SDRAM)
*B:A3,A7,B2,B8,D2,D8,E3,E7, F2,F8,H2,H8,J3,J7,N1,P9
*A:A1,A9,C1,C3,C7,C9,E1,E9, G1,G3,G7,G9,J1,J9,M9,R1
1-U32-U33-U4
4-U35-U36-U4
S0-DQ15S0-DQ14S0-DQ13S0-DQ12S0-DQ11S0-DQ10S0-DQ9S0-DQ8
S0-DQ7S0-DQ6S0-DQ5S0-DQ4S0-DQ3S0-DQ2S0-DQ1S0-DQ0
S0-DQ2
S0-DQ5
S0-DQ1
S0-DQ4
S0-DQ0
S0-DQ7
S0-DQ3
S0-DQ6
S0-DQ13
S0-DQ9
S0-DQ12
S0-DQ8
S0-DQ15
S0-DQ11
S0-DQ14
S0-DQ10
*B:C25,C26,D24~D26,E23~E26, F23~F26,G23~G26,H23~H26, J23~J26,K23~K26,L23,L24, M23~M26,N23~N26,P23~P26, R24,R26
1-S42-S4
3-S4
4-S35-S3
6-S3
HDMII/F
TO DIGITAL MAIN 2IC3301(2/5)
AUDIODECODER
VIDEODECODER
TO DIGITAL MAIN 3IC3301(3/5)
HDMI-CONNECTOR-3
(RESET)
CONTINUEDIGITAL 5
(MEMORY)
(USB JACK)(SW+5V)
SHUNTREGULATOR(SWITCHING)
CONTINUEDIGITAL 2
CONTINUEDIGITAL 5
CONTINUEDIGITAL 5
CONTINUEDIGITAL 2
CONTINUEDIGITAL 3
(NO CONNECTION)
(NO CONNECTION)
(NO CONNECTION)
Digital Main 4 Schematic Diagram [TYPE A]
PL11.0SCDA4
The order of pins shown in this diagram is different from that of actual IC3301. IC3301 is divided into five and shown as IC3301 (1/5) ~ IC3301 (5/5) in this Digital Main Schematic Diagram Section.
1 NOTE:
10-14
P-ON+3.3V19
21 AL+3.3V
P-ON-H21
GND23OE224
P-ON+3.3V20
P-ON-H19
REMOTE25
GND3
P-ON+5V13
BACKLIGHT-ADJ28
BACKLIGHT-SW26
CN3701VCOM-PWM29
VCOM-PWM
BACKLIGHT-SWREMOTE
0.1C3706
0.1C3711
P-ON-H1P-ON-H2
1000PC3719
1000PC3716
0.1C3707
IC3301(5/5)ZR39775HGCF
*1
E7 HDMI-VDD3P3E8 HDMI-VDD3P3
M6NUN6NU
AB10NUAB9AUDIO-MUTEAB8NUG2NUL6NU
NU G1K6NU
T7CORE-VDD18-STBY4
H6LVDSVCRX-VDD33J6LVDSVCRX-VDD33
AE6PROTECT5-USBAB6NUAC3NUAC4NU
AF5VDDADC8
L3AVDD18-HPLLM3AVSS-HPLL
AC11 USB-VDD1
*D CORE-VDD
T6CORE-VDD18-STBY3
0.1C3001
1000PC3103
0.01C3102
10C3587
10C3586
10C3588
10C3589
1C3591
1C3590
1C3596
1C3641
1C3592
1C3594
1C3595
1C3593
1C3597
1C3600
1C3614
1C3599
1C3615
1C3598
1C3616
1C3619
1C3620
1C3618
1C3621
1C3617
1C3622
1C3625
1C3626
1C3624
1C3627
1C3623
1C3628
0.1C3631
0.1C3632
0.1C3630
0.1C3633
0.1C3629
0.1C3634
0.1C3637
0.1C3638
0.1C3636
0.1C3635
R7CORE-VDD18-STBY5
1C3019
1C3523
F7 HDMI-VDD3P3F8 HDMI-VDD3P3*C IO-VDD
V26 PLL-VDD33
AC15 LDI-VDD33AB15 LDI-VDD33
0.1C3502
1C3571
0R3504
10C3527
10C3526
10C3528
10C3529
1C3531
1C3532
1C3533
0.1C3536
0.1C3537
0.1C3538
0.1C3540
0.1C3539
0.1C3542
0.1C3566
0.1C3543
0.1C3567
10C3530
1C3534
1C3535
0.1C3541
0.1C3032
0.1C3031
1C3033
0.1C3503
0.1C3584
0L3502
1C3585
R31030
0.1C3570
0.1C3569
0.01C3525
AL+3.3V
BACKLIGHT-ADJ
P-ON+5V14
10C3701
AUDIO(L)-OUT2
100R3702
AUDIO(R)-OUT4
100R3712
PROTECT35AMP(L)-OUT6
100R3711
GND7
100R3710
AMP(R)-OUT8
P-ON+3V10
0.1C3705
PROTECT111
100R3707
OPENC3718
100R3713
100R3709
GND12
PROTECT215
1000PC3715
100R3708
P-ON+7V160.1C3749
10C3748
1
2
3
4 5
6
7
8
IC3601BD9329EFJ-E2
BST
VIN
SW
GND FB
COMP
EN
SS
1500PC3606
16KR3603
47KR3601
6.8KR36029.1KR3615
L360122uH
C3608100/4VD3601
OPEN
0.1C3607
0.1C3604
10C3603
10C3602
1C3605
10C3611
1KR36071K
R3608
510R3609
22KR3616
DDR+1.8V0.1C3568
0R3110
AC13 USB-VDD33
1C3105
AF25 USB2-VDD330R3112
0.1C3114
1C3043
0R3656
OPENR3657
AE3NU
0.1C3508
1C3572 E10 HDMI-VDD1V
0R3505
F9 HDMI-VDD1VF10 HDMI-VDD1V
E9 HDMI-VDD1V
0.1C3612 C3544
100/4V
0.1C3610
10C3609
GND17GND1810
C3709
10KR3610
BC3601BKP1608HS391-T
0.1C3613
22 AL+3.3V
10C3708
10KR3743
P6CORE-VDD18-STBY1R6CORE-VDD18-STBY2
P5CORE-VDD18-STBY0
1 2 3 4 5
IC3603BD7820FP-E2
CTL
VCC
GND
OUT
C
10KR3613
3.9KR3612
10KR3614
OPENC3642
0R3611
K7IOVDD-STBY4
H5IOVDD-STBY2J4IOVDD-STBY1 1
C352210C3524
J5IOVDD-STBY3
H4IOVDD-STBY0
0.1C3639
AB2 DM-PLL-VDD
0.1C3504
4.7C3505
K4NU
U6NUV6NU
100R3758OE2
100PC3710
100R3706
LED127
100R3701
100R3716
OPENR3704
1000PC3713
LED1
1000PC3712
AUDIO(L)-OUTAUDIO(R)-OUTAMP(L)-OUTAMP(R)-OUT
AB7NU
AUDIO-MUTE
845R3323
845R3322
G5LVDSVCTX-VDD33G6LVDSVCTX-VDD33P4NU
4.7C3518
Y3NUAB5VDD33-BOD
C3501100/4V
D35011SS400
AC5KEY-IN1
KEY-IN1
AD6KEY-IN2AD5PROTECT1AD4PROTECT2AE5PROTECT3
PROTECT5-USB
4.7KR3744R3039 51K
AF6RC-OSC-REXTR3AVDD3-SYNC1M4AVDD3-HPLL
22PC3051
R3040 9.1K
N3AVDD3-SYNCN4AVDD3-AFE
0.1C3510
1C3509
0.1C3511
1000PC3512
0.01C3513
1C3519
1C3554
*E M-VDD
0.1C3555
10C3545
10C3546
0.1C3556
10C3550
10C3547
0.1C3557
1C3551
10C3548
0.1C3558
0.1C3581
1C3552
0.1C3582
1C3553
0.1C3559
P2AVDD18-RP1AVDD18-GR1AVDD18-BR2AVDD18-SVIDEOP3AVDD18-CVBS
1000PC3514
1C3520
0.01C3515
R4DVDD18
1C3507
0.01C3506
0.1C3521
AC2IF-VDD3P3AC1IF-VDD3P3
4.7C3011
0.1C3010
L3001BK1608HS601-T
AE10ACOD3-AVDDAE11ACOD3-AVSS 0.1
C30181C3012
L3003BK1608HS601-T
*FVFE-AVSS
1C3106
0.1C3104
10C3549
0.1C3560
0.1C3562
0.1C3564
0.1C3563
0.1C3561
0.1C3565
0.1C3577
0.1C3580
0.1C3579
0.1C3578
L3501BK1608HS601-T
BC3001BK1608HS601-T
BC3502BK1608HS601-T
BC3503BK1608HS601-T
BC3505BK1608HS601-T
BC3506BK1608HS601-T
P-ON+5V
10C3703
AL+3.3VP-ON+3.3V
REMOTEP-ON+5V
10C3643
P-ON+3.3VP-ON+1.8V
1000PC3722
100PC3704
1000PC3717
1000PC3720
10C3644
P-ON+3.3V
OPENR3745
PROTECT1PROTECT3PROTECT2
OPENR3617
10C3640
OPENC3653
OPENR3655
OPENC3652
OPENC3651
OPENR3654
BC3602OPEN
OPENR3653
1 2 3 4 5
IC3651OPEN
CTL
VCC
GND
OUT
C
C3655OPENOPEN
C3654
100KR3012
0.1C3062
100R3714
1000PC3721
R3008 OPENR3009 10K
R3010 OPENR3011 OPEN
100PC3751
P-ON-H1
P-ON+3.3V
OPENR3652
OPENR3651
1000PC3646
10R3604
1000PC3647
10R3605
10C3648
OPENC3645
0.01C3601
R3013 OPEN
OPENC3061
L3602BEAD
1000PC3702
1000PC3723
OPEN
R3777
BACKLIGHT-ADJ(1)LCD+12V(1)
OPEN
R3861
OPEN
R3759
100R3705
OPENR3757
1 2 3 4 5
IC3602BD7820FP-E2
CTL
VCC
GND
OUT
C
DDAA
4
1
3
2
CCY BBZ
DIGITAL MAIN CBA UNIT
TO POWER SUPPLYCBA CN301
DIGITAL SIGNAL PROCESS/MAIN MICRO CONTROLLER
*D:F11~F15,G12~G16,L20,L21,M20,M21, N20,N21,P20,P21,R20,R21,T20~T26, U20,U21,V7,V20,V21,W7,W20,W21, Y7~Y15,AA7~AA15
*C:G7~G11,H7,H8,J7,Y16~Y21,AA16~AA26
*E:E20~E22,F16~F22,G17~G22,H20~H22, J20~J22,K20,K21
CONTINUEDIGITAL 2
CONTINUEDIGITAL 2
(DC-DC CONVERTER)
(+1.8V REG.)
(+1.8V REG.)
*F:L7,M7,N7,P7,U7,W4~W6,Y4~Y6
CONTINUEDIGITAL 3
CONTINUEDIGITAL 2
CONTINUEDIGITAL 4
CONTINUEDIGITAL 1
CONTINUEDIGITAL 3
CONTINUEDIGITAL 4
CONTINUEDIGITAL 4
Digital Main 5 Schematic Diagram [TYPE A]
PL11.0SCDA5
The order of pins shown in this diagram is different from that of actual IC3301. IC3301 is divided into five and shown as IC3301 (1/5) ~ IC3301 (5/5) in this Digital Main Schematic Diagram Section.
1 NOTE:
10-15
VIDEO SIGNAL
1 STV
3 OE1
6 TP
4 CPV5 POL
2 XA0
CN300524 GND
13 LLV3(+)
10 LLV4(-)
15 LLVCLK(-)16 LLVCNK(+)
12 LLV3(-)
19 LLV2(+)
11 LLV4(+)
18 LLV2(-)
20 LLV1(-)21 LLV1(+)
R15P14P13N16N15P16P15T16T15R14T14R13T13
K15NU
17 GND
14 GND
9 LLV5(+)8 LLV5(-)7 GND
P-ON+3.3V7.5KR3088
RESET-LCD
1 NU
11 NU
3 NU4 NU
7 GND8 NU
24 GND
5 NU
9 NU
2 NU
6 NU
10 NU
25 GND26 GND27 LCD+12V28 LCD+12V29 LCD+12V
CN301131 LCD+12V30 LCD+12V
Q3001OPEN
OPENR3007
OPENR3006
OPENC3002
OPENR3002
OPENR3001
100K
R356
6
OPEN
R356
3
0R3537
R16
*1IC3005(1/6)R8A05011BG-U0
LCD+12V
N14LESET LCD
Q3002OPEN
1 2 3
678
4
5
OPENC3345
19 LLV2(+)20 LLV1(-)21 LLV1(+)
16 LLVCNK(+)17 GND
15 LLVCLK(-)
23 LLV0(+)22 LLV0(-)
14 GND13 LLV3(+)
18 LLV2(-)
12 LLV3(-)
23 LLV0(+)22 LLV0(-)
OPENC3349
OPENC3350
OPENC3351
OPENC3352
OPENC3353
OPENC3354
OPENC3355
L13TPM15POL
M16NU
100K
R356
5
L16CPV
100K
R356
4
L15OE
100K
R356
2
M14STV
M13NU
N13NU
OPENR3552OPENR3553OPENR3554OPENR3555
OPENR3557
OPENR3559OPENR3558
OPENR3556
OPENR3561OPENR3560
OE2L14OE2
1KR3152
100P
C356
710
0KR3
567
K16SM-CLKOPENR3210OPENR3514
K14SM-MOSIJ16SM-MOSO
OPENR3515
F14SM-PU-CONT
CN39011 SM-CLK2 SM-MISO3 NU4 SM-MISI5 GND6 REMOTE
REMOTEAL+3.3VP-ON+5V
D3905OPEN
L3902 OPEN
Q3903OPEN
D3904OPEN
D3903OPEN
D3902OPEN
D3901OPEN
L3901 OPEN
L3903 OPEN
L3904 OPEN
OPENR3902
OPENR3918
OPENC3901
Q3907OPEN
Q3908OPEN
OPENR3917
OPENR3916
OPENR3907
OPENR3909
OPENC3905
Q3906OPEN
P-ON+3.3V
OPENR3904
OPENR3906
OPENR3910
OPENR3911
Q3904OPEN OPEN
R3921OPENR3914
OPENR3925
Q3905OPEN
OPENR3913
OPENR3912
D3907OPEN
OPENR3905
OPENC3904
Q3901OPEN OPEN
R3901
OPENC3903
OPENC3902
OPENR3903
OPENR3920
OPENR3919
D3906OPENOPEN
R3908
IC3901OPEN
1
OE
2
A
3
GND
4
Y
5
VCC
OPENR3915
OPENC3906
DIGITAL SIGNAL PROCESS/MAIN MICRO CONTROLLER
TO LCD MODULEASSEMBLY
LVDSTX
TO DIGITAL MAIN 2IC3005(2/6)
4
1
3
2
DC FA B E
CONTINUEDIGITAL 5
DIGITAL MAIN CBA UNIT
CONTINUEDIGITAL 5
CONTINUEDIGITAL 2
(NO CONNECTION)
(SMART PORT)
CONTINUEDIGITAL 5
PL11.0SCDB1
Digital Main 1 Schematic Diagram [TYPE B]
The order of pins shown in this diagram is different from that of actual IC3005. IC3005 is divided into six and shown as IC3005 (1/6) ~ IC3005 (6/6) in this Digital Main Schematic Diagram Section.
1 NOTE:
10-16
GND7
COM-VIDEO-Y-IN15
GND1
GND9S-VIDEO-Y-IN8
SPDIF2
RESET23
AUDIO-MUTE20
CN3006KEY-IN129
GND25
S-VIDEO-C-IN6
COM-VIDEO-Pr-IN19
GND16COM-VIDEO-Pb-IN17
VIDEO-IN4
33PC3107
33PC3104
33PC3103
33PC3093
33PC3095
33PC3098
1000PC3092
1000PC3074
100R3404
33PC3111
A10C8
B9
B11
C10
D8C9
C11
A9C7
0.1C32020.1C3290
0.1C3284
0.1C3201
0.01C3198
0.1C32000.1C3199
OPENC3196
OPENC3194OPENC3195
DIF-OUT228
DIF-OUT126
IF-AGC24
AUDIO(R)11INPUT012
SCL22SDA21
AUDIO(L)13
33PC3100
SDASCL
AUDIO-MUTE
A12
A16IF-AGC
22R3511
SPDIF
GND3
S-VIDEO-SW5
33PC3105
100R3175
INPUT110
33PC3102
22R3187
100R3171AUDIO(R)
100R3154AUDIO(L)
GND14
GND18
100R3144100R3142100R3138
100R3134
GND27
KEY-IN1
N12S-VIDEO-SW
G1INPUT0D1INPUT1
100PC3099
OPENC3084
P-ON+5V
100PC3101
100PC3112
OPENR3181
OPENR3532
Q30102SC4081UBTLQ
10KR3184
10KR3185
LIGHT-SENSRESET
OPENR3416
OPENR3356 D3049
OPEN
OPENR3364
OPENR3284 1
2
3
4
5
14
13
12
11
15
6
7
8
9
10
JK3001PC-RGB-INOPEN
D3055OPEN
D3053OPEN
OPENR3377
OPENR3285
OPENR3286
OPENR3376D3040
OPEND3027OPEN
OPENR3326
OPENR3333
D3041OPEN
OPENR3321
OPENR3334
D3054OPEN
1
2
3 4
VCC
GND
5
IC3013OPEN
1
2
3 4
VCC
GND
5
IC3014OPEN
OPENC3214
AL+3.3V(2)
B14VGA-VSYNCA14VGA-HSYNC
OPENR3296
OPENR3339
OPENR3347 D3045
OPEN
OPENR3358 D3050
OPEN
OPENR3343
1C33360.1C32860.1C3285
D10NUA11NUB10NU
33P
C3289
33P
C3255
33P
C3256
33P
C3288
33P
C3287
56R340056R3399
56R3398
22R3401
22R3403
22R3402
100R3183
39KR3186
D3056OPEN
RESET-LCD
B12
IC3005(2/6)R8A05011BG-U0
*1
D9NU
OPENR3298
L30220.27uH 33P
C3235
L3024OPEN
L3023OPEN
OPENC3243
OPENR3369
OPENR3361
OPENR3360
OPENC3242
OPENR3368
2.2KR3202
0.1C3178
OPENC3177
47R3091
33PC3089
1000PC3086
33PC3087
10KR3513
10KR3189
100R3156
100R317233P
C3254
OPEN
C3291
OPEN
C3292
OPEN
C3293
0.1C3197
2.2C3335
10PC322510PC3226
VGA-SCLVGA-SDAP-ON+5V(1)
4
JI
3
2
L
1
G H K
DIGITAL MAIN CBA UNIT
TO POWER SUPPLYCBA CN302
DIGITAL SIGNAL PROCESS/MAIN MICRO CONTROLLER
CONTINUEDIGITAL 4
CONTINUEDIGITAL 3
SW
A/DCONVERTER
DEMODULATOR/MPEGDECODER
DIGITALSIGNALPROCESS
TO DIGITAL MAIN 6IC3005(6/6)
TO DIGITAL MAIN 1IC3005(1/6)
CONTINUEDIGITAL 3
TO DIGITAL MAIN 3IC3005(3/6)
(BUFFER GATE)
(BUFFER GATE)
CONTINUEDIGITAL 1
CONTINUEDIGITAL 5
CONTINUEDIGITAL 6
(BUFFER)
PL11.0SCDB2
Digital Main 2 Schematic Diagram [TYPE B]
The order of pins shown in this diagram is different from that of actual IC3005. IC3005 is divided into six and shown as IC3005 (1/6) ~ IC3005 (6/6) in this Digital Main Schematic Diagram Section.
1 NOTE:
10-17
B7A7C5NU
10C3216
A810C3217
AUDIO(L)
B810C3218
AUDIO(R)
D11NU
C12LPF
SPDIF
AUDIO(L)-OUT
OPENR3503
OPENR3504
AUDIO(R)-OUTAMP(L)-OUTAMP(R)-OUT
100R3335100R3336
100PR3500
100PR3499
100R3209
100R3325
100R3322
C6NUD7NU
B16P-ON-H2
VCOM-PWM
P-ON-H2
F2VCOM-PWM
C14REMOTE
REMOTE
A15KEY-IN1
KEY-IN1LIGHT-SENS
A13LIGHT-SENSC13PROTECT1
PROTECT1
D13PROTECT2
PROTECT2
B13PROTECT3
PROTECT3
G13DTV-ON-H2
DTV-ON-H2
F13DTV-ON-H1100R3215
DTV-ON-H1
22R3213
100R3517
22R331522R3313
100R3314
22R3316
22R3233
22R3312
3.3KR3178 100
R3191
RESET
0.1C3106
0.1C3252
56KR3182
32
1 4
IC3009BU4221F
CDVDD
GND OUT
J15RESET-N
0.47C3113
OPENC3116
1000PC3120
AL+3.3V
CPU-RESET-N
OPENR3501
OPENR3502
10KR3340
0.22C3231
P-ON+3.3V(2)
10C321910C3220
A6B6
100PC3229
100PC3227
100PC3341
100PC3338
100R3518
100R3520
1C3337
1C3340
10C3223
10C3224
100KR3498
OPENC3228
N10
IC3005(3/6)R8A05011BG-U0
*1
SPDIF
0R3341
4
PO
3
2
R
1
M N Q
DIGITAL SIGNAL PROCESS/MAIN MICRO CONTROLLER
AUDIOI/F
CONTINUEDIGITAL 2
DIGITAL MAIN CBA UNITCONTINUEDIGITAL 5
TO DIGITAL MAIN 2IC3005(2/6)
TO DIGITAL MAIN 6IC3005(6/6)
CONTINUEDIGITAL 4
CONTINUEDIGITAL 2
CONTINUEDIGITAL 5
(RESET)
CONTINUEDIGITAL 5
Digital Main 3 Schematic Diagram [TYPE B]
PL11.0SCDB3
The order of pins shown in this diagram is different from that of actual IC3005. IC3005 is divided into six and shown as IC3005 (1/6) ~ IC3005 (6/6) in this Digital Main Schematic Diagram Section.
1 NOTE:
10-18
IC3002K4T51163QI-HCF7
*A VDD
J2VREF
E2 NU K2CKEJ8CKK8CKL8CSK7RASL7CASK3WEL1BA2/NCL3BA1L2BA0R2A12P7A11M2A10/APP3A9P8A8P2A7N7A6N3A5N8A4N2A3M7A2M3A1M8A0K9ODT
*BVSS
A2 NUR8 NUR7 NUR3 NU
B7 UDQSA8 UDQS/NUB3 UDMB9 DQ15B1 DQ14D9 DQ13D1 DQ12D3 DQ11D7 DQ10C2 DQ9C8 DQ8F7 LDQSE8 LDQS/NUF3 LDMF9 DQ7F1 DQ6H9 DQ5H1 DQ4H3 DQ3H7 DQ2G2 DQ1G8 DQ0
N8 SD-DQ14P7 SD-DQ13R6 SD-DQ12P6 SD-DQ11N7 SD-DQ10T5 SD-DQ9P8 SD-DQ8P4 SD-DQ7T3 SD-DQ6R4 SD-DQ5T2 SD-DQ4P3 SD-DQ3T4 SD-DQ2R3 SD-DQ1N4 SD-DQ0T6 SD-UDMR5 SD-LDMT7 SD-UDQSNR7 SD-UDQSN5 SD-LDQSNP5 SD-LDQS
J3 SD-RASH3 SD-CASL4 SD-WE
R1 SD-CLKNR2 SD-CLKL3 SD-CKEK2 SD-ODTM2 SD-A12
P1 SD-BA2
L1 SD-A1
H1 SD-A4
K1 SD-A2
H2 SD-A8L2 SD-A9
N1 SD-A7
K4 SD-BA1
J2 SD-A11
K3 SD-A6
J1 SD-A0
M3 SD-A3
J4 SD-A10
N2 SD-BA0
M1 SD-A5
0.1C3009
0.1C3010
R10USBDPT10USBDN
P-ON+5V
1
2
3
4 5
6
7
8
IC3006MX25L3205DM2I-12G
CS
SO
WP
GND SI
SCK
NU
VCC
T12SDAR12SCL
SCLSDA
3USBDP4GND
2USBDN
CN30091BUS-POWER
1C3246
R11SOUTP11SINT11SCK
P12CS
0.1C30290.1C30300.1C30310.1C30320.1C30330.1C30340.1C30350.1C30360.1C30370.1C30380.1C30390.1C30400.1C3041
10KR3104
P-ON+3.3VAL+3.3V
P-ON+1.8VH4 NU
6.8R30246.8R3015
15R3048
15R3038
15R3031
15R303515R303615R3037
15R3016
15R302915R3030
15R304015R3039
15R304115R304215R3043
15R3047
15R304515R3046
15R3044
15R3032
15R303415R3033
100R3049
2 UART0-TXG16RXD0
OPENC3253
3 UART0-RX
4.7KR3395
4 GND4.7KR3396
G15TXD0
CN30101 P-ON+5V
L3004BLM21PG221SN1D
10KR3107
10KR3102
L3025EXC24CG900U
D3052OPEN
47R3089
47R3092
47R309447R3093
22R320622R3207
E2BACKLIGHT-SW22R3188
C1P-ON-H1
OPENR3190
BACKLIGHT-SW
P-ON-H1
P10NU5.6KR3099
H14NU10C30720.1C3071
IC3005(4/6)R8A05011BG-U0
*1
M5 SD-VREF0
R8 SD-DQ15
N3 GND0.1C3051
100R3065
0.1C3050
100R3064
G14LED1
LED1
0.1C3073 150R3070
2 GND
CN30071 AL+3.3V
4 ASEMD05 TRST-N6 TCK
3 ASEBRKAK-N
9 TMS10 CPU-RESET-N
8 TDO7 TDI
G2M32TRST-N
10KR3224
F15ASEBRKAK-NF16ASEMD0E16TRST-NE15TCKD16TDID15TDOE14TMS
CPU-RESET-N
E13GPY10
GPY10
E1AUDIO-MUTE
OPENR3234
22R3510
AUDIO-MUTE
F3BACKLIGHT-ADJ100R3516
BACKLIGHT-ADJ
J14GNDH15XIN25H16XOUT25
1KR3223
X300125MHz
18PC3184
18PC3183
CPU-RESET-N
OPENC3176
OPENC3175
100R3468100R3469
10KR3522
1
2
3 4
5
IC3019BD2224G-TR
VIN
GND
/EN /OC
VOUT
100/16VC3348
R9GPIO5T9GPIO4
22R3095
10KR3480
10KR3479
0.1C3327
L3041BLM21PG221SN1D
4.7KR3204
4.7KR3203
2.2KR3201
SCLSDA
DIGITAL MAIN CBA UNIT
DIGITAL SIGNAL PROCESS/MAIN MICRO CONTROLLER
(DDR2 SDRAM)
*B:A3,A7,B2,B8,D2,D8,E3,E7, F2,F8,H2,H8,J3,J7,N1,P9
*A:A1,A9,C1,C3,C7,C9,E1,E9, G1,G3,G7,G9,J1,J9,M9,R1
1-V32-V33-V3
4-V35-V36-V3
SD-DQ15SD-DQ10SD-DQ12SD-DQ11SD-DQ13SD-DQ14SD-DQ9SD-DQ8
SD-DQ7SD-DQ6SD-DQ5SD-DQ4SD-DQ3SD-DQ2SD-DQ1SD-DQ0
SD-DQ2
SD-DQ5
SD-DQ1
SD-DQ4
SD-DQ0
SD-DQ7
SD-DQ3
SD-DQ6
SD-DQ13
SD-DQ9
SD-DQ12
SD-DQ8
SD-DQ15
SD-DQ11
SD-DQ14
SD-DQ10
1-S32-S3
3-S3
4-S35-S3
6-S3
(MEMORY)
(USB JACK)
CONTINUEDIGITAL 5
2
S V
1
T U
3
4
W X
(NO CONNECTION)
CONTINUEDIGITAL 5
(NO CONNECTION)
CONTINUEDIGITAL 2
CONTINUEDIGITAL 3
(HIGH SIDE SW)
CONTINUEDIGITAL 6
Digital Main 4 Schematic Diagram [TYPE B]
PL11.0SCDB4
The order of pins shown in this diagram is different from that of actual IC3005. IC3005 is divided into six and shown as IC3005 (1/6) ~ IC3005 (6/6) in this Digital Main Schematic Diagram Section.
1 NOTE:
10-19
P-ON+3.3V19
21 AL+3.3V
P-ON-H21
GND23OE224
P-ON+3.3V20
P-ON-H19
REMOTE25
GND3
P-ON+5V13
BACKLIGHT-ADJ28
BACKLIGHT-SW26
CN3002VCOM-PWM29
BACKLIGHT-SW
0.1C3016
0.1C3022
P-ON-H1
1000PC3055
1000PC3067
0.1C3047
*CVDD12
AL+3.3V
P-ON+5V14
10C3045
AUDIO(L)-OUT2
100R3087
AUDIO(R)-OUT4
100R3085
AMP(L)-OUT6
100R3078
GND7
100R3074
AMP(R)-OUT8
P-ON+3V10PROTECT111
OPENC3048
100R3101
100R3072
GND12
PROTECT215
1000PC3044
P-ON+7V160.1C3043
10C3028
1
2
3
4 5
6
7
8
IC3008BD9329EFJ-E2
BST
VIN
SW
GND FB
COMP
EN
SS
1500PC308816KR3137
47KR3143
12KR3145
5.6KR3149
L300922uH
D3001SK22A
0.1C3085
10C3080
0.022C3083
1C3090
1 2 3 4 5
IC3007BD7820FP-E2
CTL
VCC
GND
OUT
C
42.2KR311156K
R3110
4.7KR3109
GND17GND1810
C3019
22 AL+3.3V
10C3015
1 2 3 4 5
IC3004BD7820FP-E2
CTL
VCC
GND
OUT
C
20KR3060
1KR3059
33KR3061
100R3017
OE2
100PC3008
100R3014
NU27
100R3008
100R3009
OPENR3010
OPENC3005
LED1
100R3011
1000PC3006
AUDIO(L)-OUTAUDIO(R)-OUTAMP(L)-OUTAMP(R)-OUT
AL+3.3V(2)
P-ON+5V
P-ON+3.3V
100PC3003
1000PC3061
1000PC3057
AUDIO SIGNAL
1000PC3062
OPENR3531
OPENR3062
10C3097
10KR3079
*D VSS
Q30042SC4081UBTLQ
AL+3.3V(2)
LCD+12V
OPENR3526
OPENR3525
OPENR3524
BACKLIGHT-ADJ
0R3050
0R3054
Q30032SC4081UBTLQ
2.2KR3086
2.2KR3084
10KR3077
C309447/4V
0.1C3122
0.1C3123
0.1C3124
0.1C3129
0.1C3121
0.1C3128
G12VCC33STB 0.1C3182
E12VDDSTB
0.1C3181
100R3221
10KR3222 GPY10
0.1C3125
J13AVDD12K6AVDD12M11AVDD12
L3015BLM21PG221SN1D
F5VCCQ33G4VCCQ33J12VCCQ33K13VCCQ33
N11AVDD33
0.1C3126
10C3133
OPENC3134
H5VCCQ18J5VCCQ18M4VCCQ18M6VCCQ18M7VCCQ18M8VCCQ18N6VCCQ18T1VCCQ18
M10AVDD12
E8AVDD12F8AVDD12F9AVDD12
L3014BLM21PG221SN1D
10C3325
10C3343
10C3326
10C3324
L3020BLM21PG221SN1D
0.1C3135
0.1C3136
10C3346
0.01C3264
P-ON+1.8V
C3049100/4V
10C3024
10C3023C3108
100/16V
L3001BLM21PG221SN1D
0.1C3027
1C3263
0.1C3070
10C3069
10C3068
0.1C3053
E10AVDD33C2AVDD33C3AVDD33E11AVDD33
D6ADAC
E6AADC
L3019BLM21PG221SN1D
0.1C3149
0.1C3147
0.1C3117
0.1C3150
10C3347
0.1C3151
0.1C3154
L3026BLM21PG221SN1D
G11VDDCLK
0.1C3139
C3077100/16V
L3003BLM21PG221SN1D
10KR3133
PROTECT1
P-ON-H2
PROTECT2
VCOM-PWM
PROTECT3DTV-ON-H2
REMOTE
DTV-ON-H1
100R3068100R3058
1000PC3046
1000PC3004
P-ON+3.3V
P-ON+3.3V
22KR3106
1KR3105
Q30052SC4081UBTLQ
D31011SS400TE61D31021SS400TE61
22KR3100
2.2KR3097
C3079100/4V
Q31012SC4081UBTLQ
47KR3423
CPU-RESET-N
100R3424 D3103
1SS400TE61
D31041SS400TE61
D31051SS400TE61
1C3054
D31061SS400TE61
H13 AVSS12L10 AVSS12
D2 AVSS33
P-ON+3.3V(2)
100R3083
AL+3.3V
Q30062SA1774TLQ
100PC3011
1000PC3063
1000PC3065
G10 AVSS12G8 AVSS12G9 AVSS12E9 AVSS33
D3 AVSS33D12 AVSS33D5 AVSS33E7 AVSS33E3 PD1E4 PD1D4 PD1E5 PD1
0.1C3160
Q3013SSM3K309T
GD S
L12VCCQ33
L3027BLM21PG221SN1D
OPENC3075
10C3076
L3021BLM21PG221SN1D
10C3096 OPEN
D3002
10R3141
1000PC3091
L3016BLM21PG221SN1D
0.1C3157
0.1C3158
0.1C3159
10C3322
L3044BLM21PG221SN1D
OPENR3464
10C3052BC3001
BLM21PG221SN1D
C3060220/6.3V
C3066220/6.3V
0.1C3127
P-ON+5V
10C3265
10C3081
0.1C3082
L3028BLM21PG221SN1D
0.1C3142
0.1C3144
0.1C3141
0.1C3143
0.1C3140
0.1C3145
10C3321
10C3320
10C3319
10C3318
10C3114
0.1C3148
F12
IC3005(5/6)R8A05011BG-U0
*1
VCC33STB
P-ON+3.3V(2)
L3043 BLM21PG221SN1D
0.1C3152
C3060AOPEN
REMOTEAL+3.3VP-ON+5VP-ON+3.3V
PROTECT35
F10 VSSCLK
L3030BEAD
C3066AOPEN
L3029BEAD
DDAA
4
1
3
2
CCY BBZ
DIGITAL MAIN CBA UNIT
TO POWER SUPPLYCBA CN301
DIGITAL SIGNAL PROCESS/MAIN MICRO CONTROLLER
(DC-DC CONVERTER)
(+1.8V REG.)
(+1.8V REG.)
CONTINUEDIGITAL 3
CONTINUEDIGITAL 2
CONTINUEDIGITAL 1
CONTINUEDIGITAL 3
CONTINUEDIGITAL 4
CONTINUEDIGITAL 6
(SWITCHING)
CONTINUEDIGITAL 4
CONTINUEDIGITAL 1
(SW+3.3V)
(SWITCHING)
(SWITCHING)
(SWITCHING)
(SWITCHING)
CONTINUEDIGITAL 6
*D:F4,F6,F7,F10,F11,G7,H7~H12, J6,J8~J10,K5,K8~K10,K12, L5~L7,L11,P2,T8
*C:G5,G6,H6,J7,J11,K7,K11,L8, L9,M9,N9,P9
CONTINUEDIGITAL 3
CONTINUEDIGITAL 1
Digital Main 5 Schematic Diagram [TYPE B]
PL11.0SCDB5
The order of pins shown in this diagram is different from that of actual IC3005. IC3005 is divided into six and shown as IC3005 (1/6) ~ IC3005 (6/6) in this Digital Main Schematic Diagram Section.
1 NOTE:
10-20
16 HDMI-DATA
14 NU
17 GND
13 HDMI-CEC
15 HDMI-CLOCK
16 HDMI-DATA
14 NU
17 GND
13 HDMI-CEC
15 HDMI-CLOCK
0.01C3311
0.01C3313
0.1C3312
10C3316
0.1C3310
L3046BLM21PG221SN1D
P-ON+3.3VAL+3.3V(2)
Q30142SK3018T106
27KR3237
A4
A3B4
B1A1
B3
B2A2
14 NU
9 TMDS-D0(-)10 TMDS-CLOCK(+)
3 TMDS-D2(-)
17 GND
11 C-SHIELD0
7 TMDS-D0(+)
2 D-SHIELD0
JK30031 TMDS-D2(+)
13 HDMI-CEC
8 D-SHIELD2
4 TMDS-D1(+)
6 TMDS-D1(-)5 D-SHIELD1
12 TMDS-CLOCK(-)
15 HDMI-CLOCK16 HDMI-DATA
47KR3278
47KR3275
47KR3274
47KR3276
47KR3273
D3057RB751S-40TE61
82KR3415
13
1
15
14
16
3
6
5
11
4
7
12
10
8 9
2
IC3011BU9883FV-WE2
VCC1
SDA1
WPB
VCC-OUT
SDA0
SCL0
VCC0 VCC3
SCL3
SDA3
GND
NU
SDA2
SCL2
VCC2
SCL1
D14HDMI1-HPD
C15HDMI1-SDA
C16HDMI1-SCL
4.7KR3487
0.1C3191
4.7KR3488
22R3508
G3HDMI-SEL0
22R3509
F1HDMI-SEL1
0.1C3314
0.01C3315
0.1C3333
0.01C3332
0.01C3334
0.1C3331
0.1C3300
0.1C3302
0.1C3304
0.01C3301
0.01C3303
0.01C3307
0.01C3309
0.01C3305
0.1C3308
0.1C3306
4.64KR3486
4.7KR3497
0.1C3190
0.1C3212
0.1C3213
0.1C319210KR3523
100R3282
100R3281
4.7KR3496
100R3405
10KR3489
1C3260
18 +5V
R3375OPEN
R338510K
OPENR3414
R33741K
1KR3406
19 HOT PLUG DETECT
2SC4081UBTLQQ3032
0R3512
0R3477
0R3478
OPENR3476
OPENR3475
B5PLL-XFC-AA5PLL-XFC-P
C4EXT-RES
2.2KR3270
2.2C3187
4700PC3186
3KR3271
2200PC3188
560R3236
0.01C3185
P-ON+3.3V(2)
SCLSDA
10KR3302 Q3301
2SC4081UBTLQ
10KR3304
18 +5VR33701K
R3371OPEN
0R3387
1C3262
R338610K
1KR3408
OPENR3412
19 HOT PLUG DETECTR34112.7K
D30671SS400TE61
R34092.7K
D30651SS400TE61
R33721K
R3373OPEN
19 HOT PLUG DETECT
OPENR3413
2SC4081UBTLQQ3031
0R3388
18 +5VD30661SS400TE61
33KR3301
1KR3407
M12PWR
10KR3293
R338310K
R34102.7K1
C3261
47KR3277
P-ON+5V(1)OPENR3507
HDMI-CEC B15
IC3005(6/6)R8A05011BG-U0
*1
12 TMDS-CLOCK(-)
4 TMDS-D1(+)
8 D-SHIELD2
11 C-SHIELD0
2 D-SHIELD03 TMDS-D2(-)
10 TMDS-CLOCK(+)
7 TMDS-D0(+)6 TMDS-D1(-)
JK30041 TMDS-D2(+)
9 TMDS-D0(-)
5 D-SHIELD1
10 TMDS-CLOCK(+)
JK30021 TMDS-D2(+)
8 D-SHIELD2
4 TMDS-D1(+)3 TMDS-D2(-)
5 D-SHIELD1
12 TMDS-CLOCK(-)
7 TMDS-D0(+)
9 TMDS-D0(-)
2 D-SHIELD0
6 TMDS-D1(-)
11 C-SHIELD0
VGA-SCLVGA-SDA
HDMI SW
IC3018BU16029KV-E2123
GND
456
VCC
789
GND
101112
VCC
131415
GND
16
NU
21
22 GND
23
24
25 VCC
26
27
28 GND
29 SCL-SINK
30 SDA-SINK
31 HOT-PLUG-DETECT-SINK
32 HDMI-SEL0
33
HDMI-
SEL1
34
NU
35
HOT-PLUG-
DETECT1
36 37 38 39 40
VCC
41 42 43
GND
44 45 46
VCC
47 48
49NU
50HOT-PLUG-DETECT2
51
52
53
54
55VCC
56
57
58GND
59
60
61VCC
62
63
64HOT-PLUG-DETECT3
20
19 VCC
18
17
10KR3294
1.5KR3303
DIGITAL SIGNAL PROCESS/MAIN MICRO CONTROLLER
3
2
1
4
EE FF GG HH II JJ
CONTINUEDIGITAL 5
(BUFFER)
HDMII/F
VIDEODECODER
TO DIGITAL MAIN 3IC3005(3/6)
TO DIGITAL MAIN 2IC3005(2/6)
AUDIODECODER
(HDMI SW)
DIGITAL MAIN CBA UNIT
HDMI-CONNECTOR-2
(HDMI SERIAL EEPROM)
HDMI-CONNECTOR-1
CONTINUEDIGITAL 4
(SWITCHING)
CONTINUEDIGITAL 5
(SWITCHING)
CONTINUEDIGITAL 2
(SWITCHING)
HDMI-CONNECTOR-3
2SC4081UBTLQQ3030
(SWITCHING)
Digital Main 6 Schematic Diagram [TYPE B]
PL11.0SCDB6
The order of pins shown in this diagram is different from that of actual IC3005. IC3005 is divided into six and shown as IC3005 (1/6) ~ IC3005 (6/6) in this Digital Main Schematic Diagram Section.
1 NOTE:
10-21
TM601
TM602
1
2
C7A3 A3
TOOL NO.
1 2 3 4 5 6 7 8 9 10
RISK
OF
FIRE
-RE
PLAC
E FU
SE A
S MA
RKED
12
3
BA01F2F0102 7 A
1
2 3
4
BA01F2F0102 7 B
J124
J319
J125
J126
R402
J127J128 GND
R210
J129
R405
JS301
R406
R212
JS302
R407
JS303
J320
J322
J323
J130
J131
R601
J132
J133
R603
J134
J328
J135
R605
CN201
J136 AMP+12V
R606
J137
J139
R609
R223
J330
P-ON-H1
R224
BC841
R227
R610
R228
J141
R611
R229
J142
A-MUTE
R612
J337
J143
R613
J144
J145
J339
J146
J147
R617
J148
R618
J149
R619
J340
J341
Q871
R235
CN601
J342
Q872
R236
J343
Q873
R237
J150
J344
R620
Q874
R238
J345
J151
R621
R239
J346
J152
R622
J347
J153
R623
J154
J348
R624
J349
J155
R625
R819
J156
R626
J157
R627
J158
C204
R240
J159
CN801
CN802
R242
R243
J350
R244
TU301S
J351
R821
R245
J352J353
R247
J160
J354
J355
J161
P-ON+5V
R249
L871
J356
J162
J163
J357
J164
J358
C210
J165
J359
R635
J166
R636
J167 SPDIF
R637
R250
J168
R638
J169
R639
R253
R254
J360
J361
FH601
C601
C219
J362
C602
FH602
J363
C603
J170
J364
C604
J365
AMP+12V
C605
J172
J366
C606
J173
J367
C607
J174
J368
GND
C608
C220
J369
J175
R645
C609
JK841
J176
C222
R646
J177
C223
J178
C224
R649
C225
J370
C610
J371
C611
J372
J373
C613
J180
J374
C614
R650
J375
C615
J182
J376
J183
J377
R653
J378
J184
J185
J379
R655
J186
J187
R657
J188
GND
R658
J189
J380
J381
J382
GND
C816
J383
J384
J190
R660
J385
J191
C819
R661
J192
J386
R662
J387
R663
J194
J388
R664
J195
J389
R665
J196
R666
R667
J199
C823
J390 J391
C631
J392
C632
J393
C633
C827
J394
J395
J396
R672
R673
C637
C638
R674
J399
P-ON-H1
C639
JK871
JK872
R677
R678
C831
C832
C640
C642
C644
C645
C646
R682
C647
R683
R878
C648
D201
R685
D202
R686
D203
R687
R688
D204
D205
R689
D206
D207
C650
C844
D208
D209
C652
C653
C654 C6
55
D401
C656
C657
D403
D404
D210
D211
R695
D405
Q501
D406
D407
R701
R699
D409
D601
L301
D602
D603D410
D604
D411
D412
D606
D413
D608
D414
D415
D609
D416
D417D418
D419
D801
BC301
D802D803
D804
D610
D611
D806
D612
D613
D807
D420
D615
C675
D421
D616
C676
D617
D619
D620
D621A
IC601
D622
T601
C880
C691
136D
D632
C692
C693
D633
J200
C694
D635
J202
J203
D637
J204
D638
J205
D639
J206
J207
J209
D641 D642
D643
J210
D644
J211
D645
J212
D646
J213
D647
J214
D648
J215 D649
J216J217
J218
CL701A
91CL701B
D650
JS201
D651
OE2
JS202
JS203
D653
D654
D655
J222
J223
D657
J224
D658
J225
R501
R502
J226
J227
J228 J229
CN101
D660
D661
D662
J230
R700
D664
D665
J232
D666
J233
D667
J234
J235
CN301
CN302
J237
J238
J239
JK711
D670
D671
D673
D674
J241
D675
Q771
J242
D676
Q772
J246
JK721
JK722
J254
C303
JK731
C306
JK732
JK733
C501
J263
-7V
J264
JS630
JS631
J267
JS633
J268
J269
JK741
JK742
J278
JK751
JK752
JK753
JK754
J284
GND
J286
J288
LCD+3.3V
J289
J290
J291
J292
R763
SA601
J297
J298
J299
R771
Q201
Q202
Q203
Q204
R780
Q205
R781
Q206
Q207
Q208
Q209
D301 D302
D303
R788
Q401
Q402
Q210
Q211
Q212
R790
AC601
R791
Q601
Q603
Q604
Q801
L601
L602
C771
L801
BC601
BC602
L802
BC603
L804L803
BC802BC803
BC804J101
BC805
Q631
J102
J103
J104
AMP+12V
Q634
J105
AMP+12V
Q635
J106
Q636
J107 AMP+12V
Q637
J108
Q638
Q639
J300
J301
J303
J110
Q640
J111
Q641
J306
J112
Q642
J113
J307
J114
J115
J309
J116 GND
J117
J118
J119
R203
R204
Q841
J312
J314
J120
J315
J121
J316
J122
J317
J123
F601
4A/125V
A B C E
3
D
4
F GA B C E
3
D
4
F
CN602
HOT
A B C E
3
D
4
F
HOT
TUNERS
COLD
AGND
GND
GND
GND
GND
GND
GNDGND
GND
GND
GND
GND
GND
GND
TUNER 5V
TUNER 5V
LCD 16V
LCD
16V
LCD -6V
RESET
KEY-IN1
S-Y
V-L
P-ON 9V
SW 9V
PC-L
SW 9V
HDMI
-R
HDMI-L
COMP-L
COMP-Y
COMP-Pr
COMP-Pb
A-OUT-L
A-OUT-R
A-OUT-MUTEOE2
BL-SW
BL-SW
BL-A
DJ
VCOM-PWM 9V
GND
GND
GND
GND
GND
GND
GND
PROTECT3
BL-ADJ
AOUT-R
V-R
V-L
V-R
GND
GND
P-ON 3.3V
SEL-L
OPAMP 9V
OPAMP 9V
A-MUTE
GND
GND
GND
GND
GND
KEY-IN1
P-ON 5
V
GND
GND
PROTECT2
ALL3.3V
6.7V
GND
ALL3.3V
GND
P-ON 3
.3V
PROTECT3
P-ON-H2
PROTECT1
PC-R
GND
INPUT1
INPUT0
VT 31V
TUNER 5V
GND
GND
ALL+3.3V
SPDIF
6.7V
SEL-R
GND
GND
GND
ALL+3.3V
ALL3.3V
P-ON-H2
AOUT-L
GND
AMP 13V
LCD 16V
A-MUTE
PROTECT1
GND
GND
GND
GND
6.7V
3.5Vfor1.8V
LCD 24V
GND
LCD -6V
PROTECT1
GND
GND
GND
+6.7V
+6.7V
GND
GND
GND
GND
+15Vfor13VLCD
+15Vfor13VLCD
FB
DRIVE OUT
IS
HOT+15V
HV
GND
GND
GND
6.7V
GND
GND
GND
GND
GND
+36V
+36V
-7V
GND
GND
GND
GND
VT 31V
GND
GND
P-ON 5V
ALL3.3V
3.5Vfor1.8V
6.7V
GND
GND
LCD+16V
LCD+16V
ALL+3.3V
ALL+6.0V
LOW-VOL PROTECT
LCD+16V
PROTECT2
INV+13V
GND
GND
GND
GND
GND
GND
P-ON 3.3V
HDMI-L
ALL+3.3V
GND
GNDGND
3.5Vfor1.8V
+15Vfor13VLCD
LOW-VOL PROTECT
R697
R696
D614
Q213
C815
C801
C658
D621B
D607
D652
D659
Q643
D423
J140
P-ON 5
V
J171
R702
R691R693
R698
C403
12
1514
9
1
1 5
28
29
1
21
228
29
BA01F2F01027
Power Supply CBA & Jack CBA Top View
NOTE:The voltage for parts in hot circuit is measured usinghot GND as a common terminal.
Because a hot chassis ground is present in the power supply circuit, an isolation transformer must be used when repairing.Also, in order to have the ability to increase the input slowly, when troubleshooting this type of power supply circuit, a variable isolation transformer is required.
CAUTION !Fixed voltage (or Auto voltage selectable) power supply circuit is used in this unit.If Main Fuse (F601) is blown , check to see that all components in the power supplycircuit are not defective before you connect the AC plug to the AC power supply.Otherwise it may cause some components in the power supply circuit to fail.
For continued protection against risk of fire, replace only with same type 4 A, 125V fuse.
CAUTION ! :
ATTENTION : Utiliser un fusible de rechange de même type de 4A, 125V.4A/125V
Jack CBA Power Supply CBA
10-22
J124
J319
J125
J126
R402
J127J128GND
R210
J129
R405
JS301
R406
R212
JS302
R407
JS303
J320
J322
J323
J130
J131
R601
J132
J133
R603
J134
J328
J135
R605
CN201
J136AMP+12V
R606
J137
J139
R609
R223
J330P-ON-H1
R224
BC841
R227
R610
R228
J141
R611
R229
J142
A-MUTE
R612
J337
J143
R613
J144
J145
J339
J146
J147
R617
J148
R618
J149
R619
J340
J341
Q871
R235
CN601
J342
Q872
R236
J343Q873
R237
J150
J344
R620
Q874
R238
J345
J151
R621
R239
J346
J152
R622
J347
J153
R623
J154
J348
R624
J349
J155
R625
R819
J156
R626
J157
R627
J158
C204
R240
J159
CN801
CN802
R242
R243
J350
R244
TU301S
J351
R821
R245
J352J353
R247
J160
J354
J355
J161P-ON+5V
R249
L871
J356
J162
J163
J357
J164
J358
C210
J165
J359
R635
J166
R636
J167SPDIF
R637
R250
J168
R638
J169
R639
R253
R254
J360
J361
FH601
C601C219
J362
C602
FH602
J363
C603
J170J364
C604
J365
C605
J172
J366
C606
J173
J367
C607
J174
J368
GND
C608
C220
J369
J175
R645
C609
JK841
J176
C222
R646
J177
C223
J178
C224
R649
C225
J370
C610
J371
C611
J372
J373
C613
J180
J374
C614
R650
J375
C615
J182
J376
J183
J377
R653
J378
J184
J185
J379
R655
J186
J187
R657
J188
GND
R658
J189
J380
J381
J382GND
C816
J383
J384
J190
R660
J385
J191
C819
R661
J192
J386
R662
J387
R663
J194
J388
R664
J195
J389
R665
J196
R666
R667
J199
C823
J390
J391
C631
J392
C632
J393
C633
C827
J394
J395
J396
R672
R673
C637
C638
R674
J399
P-ON-H1
C639
JK871
JK872
R677
R678
C831
C832
C640
C642
C644
C645
C646
R682
C647
R683
R878
C648
D201
R685
D202
R686
D203
R687
R688
D204
D205
R689
D206
D207
C650
C844
D208
D209
C652
C653
C654
C655
D401
C656
C657
D403
D404
D210
D211
R695
D405
Q501
D406
D407
R701
R699
D409
D601
L301
D602
D603 D410
D604
D411
D412
D606
D413
D608
D414
D415
D609
D416
D417
D418
D419
D801
BC301
D802
D803
D804
D610
D611
D806
D612
D613
D807
D420
D615
C675
D421
D616
C676
D617
D619
D620D621A
IC601
D622
T601
C880
C691
D631
D632
C692
C693
D633
J200
C694
D635
J202
J203
D637
J204
D638
J205
D639
J206
J207
J209
D641
D642
D643
J210
D644
J211
D645
J212
D646
J213
D647
J214
D648
J215
D649
J216J217
J218
CL701A
19CL701B
D650
JS201
D651
OE2
JS202
JS203
D653
D654
D655
J222
J223
D657
J224
D658
J225
R501
R502
J226
J227
J228J229
CN101
D660
D661
D662
J230
R700
D664
D665
J232
D666
J233
D667
J234
J235
CN301
CN302
J237
J238
J239
JK711
D670
D671
D673
D674
J241
D675
Q771J242
D676
Q772J246
JK721
JK722
J254
C303
JK731
C306
JK732
JK733
C501
J263
-7V
J264
JS630
JS631
J267
JS633
J268
J269
JK741JK742
J278
JK751
JK752
JK753
JK754
J284GNDJ286
J288LCD+3.3V
J289
J290AMP+12V
J291
J292
R763
SA601
J297
J298
J299
R771
Q201
Q202
Q203
Q204
R780
Q205
R781
Q206
Q207
Q208
Q209
D301
D302
D303R788
Q401
Q402
Q210
Q211
Q212
R790
AC601
R791
Q601
Q603
Q604
Q801
L601
L602
C771
L801
BC601
BC602
L802
BC603
L803L804
BC802
BC803
BC804 J101
BC805
Q631
J102
J103
J104AMP+12V
Q634
J105AMP+12V
Q635
J106
Q636
J107
AMP+12V
Q637
J108
Q638
Q639
J300
J301
J303
J110
Q640
J111
Q641
J306
J112
Q642
J113
J307
J114
J115
J309
J116GND
J117
J118 J119
R203
R204
Q841
J312
J314
J120
J315
J121
J316
J122
J317
J123
F601
4A/125V
ABCE
3
D
4
FG ABCE
3
D
4
F
CN602
HOT
ABCE
3
D
4
F
HOT
TUNERS
COLD
A
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GNDGND
GND
TUNER 5V
TUNER 5V
LCD 16V
LCD 16V
LCD -6V
RESET
KEY-IN1
S-YV-L
P-ON 9V
SW 9V
PC-L
SW 9VHDMI-R
HDMI-L
COMP-L
COMP-Y
COMP-Pr
COMP-Pb
A-OUT-L
A-OUT-R
A-OUT-MUTE
OE2
BL-SW
BL-SW
BL-ADJ
VCOM-PWM
9V
GND
GND
GND
GND
GND
GND
GND
PROTECT3
BL-ADJ
AOUT-R
V-R
V-L
V-R
GND
GND
P-ON 3.3VSEL-L
OPAMP 9V
OPAMP 9V
A-MUTE
GND
GND
GND
GND
GND
KEY-IN1
P-ON 5V
GND
GND
PROTECT2
ALL3.3V
6.7V
GND
ALL3.3V
GND
P-ON 3.3V
PROTECT3
P-ON-H2
PROTECT1
PC-R
GND
INPUT1
INPUT0
VT 31V
TUNER 5V
GND
GND
ALL+3.3V
SPDIF
6.7VSEL-R
GND
GND
GND
ALL+3.3V
ALL3.3V
P-ON-H2
AOUT-L
GND
AMP 13V
LCD 16V
A-MUTE
PROTECT1
GND
GND
GND
GND
6.7V
3.5Vfor1.8V
LCD 24V
GND
LCD -6V
PROTECT1
GND
GND
GND
+6.7V
+6.7V
GND
GND
GND
GND
+15Vfor13VLCD
+15Vfor13VLCD
FB
DRIVE OUT
IS
HOT+15V
HV
GND
GND
GND
6.7V
GND
GND
GND
GND
GND
+36V
+36V
-7V
GND
GND
GND
GND
VT 31V
GND
GND
P-ON 5V
ALL3.3V
3.5Vfor1.8V
6.7V
GND
GND
LCD+16V
LCD+16V
ALL+3.3V
ALL+6.0V
LOW-VOL PROTECT
LCD+16V
PROTECT2
INV+13V
GND
GNDGND
GND
GND
GND
P-ON 3.3V
HDMI-L
ALL+3.3V
GND
GNDGND
3.5Vfor1.8V
+15Vfor13VLCD
LOW-VOL PROTECT
R697
R696
D614
Q213
C815
C801
C658
D621B
D607
D652
D659
Q643
D423
J140P-ON 5V
J171
R702
R691 R693
R698
C403
1 2
15 14
9
1
15
28 29
1
21
228
29R401
R403
R404
R211
R213
R214
R408
R215
R216 R217
R218
R219R604
R410
R411
R412
R607
R220
R221 R222
R225
R802
R226
R803
R804
R805
R807
R808
R809
R231
R232
R233R234
R812 R813
R814
R815
R816
R817
R818
C201
C202
C203
R241
C206
C207
R820
C208
C209
R246
R248
C402
C212C213C214
C215
1
16
8
9
IC771
C216
C217C218
R641
R642 R643
R644
C221
R647
R648
C803
C804
C805
R841
C806
R842
C807
R843
C808
R844
R651
C809
R845
R846
R652
R847
R654
R848
C810
C811
R659
C814
C817
C818
R668
C820
C821C822
C824
C825
C826 C828C829
R675R676
C830
R679
C834
C835
R871
C641
C836
R872
C643
C837
R873
C838
R680
R874
C839
R875
R681R876
R877
C649
R879
C841
C842
C843
R880
C845
C651
R881
C846
R882
R883
R884
R690
R885
R886
R887
R888
R891
R892
L302
R893
L303
R894
IC201
C871
C872
C873
C874
C681
C875
IC602
C682
C876
C683
C877
C684
C878C879
IC801
C882C883
C884
C885
R301
R302
R303
R304
R305
R306
R307
R308
R309
R310
R311
R711
R712
R713
R714
R715
R716
R721
R722
R723
R724
C301
R725
C302
R726 C304
C305
C307
C308
C309
R731
R732
R733
C310
R734
C311
R735
R736
IC871
C701
C702
C703C704
R741
R742
R743R744
R745
R746
R751R752
R753R754
R755
R756R757
R758R759
C721C722
C723
C724
R760
R761
R762
C731
C732
C733
C734C735
C736
R772
R773
R774
R775
R776
R777
R778
R779
C741
C742C743
C744
R782
R783
R784
R785
R786
R787
R789
C751C752
C753C754
C755
C756
R792
C757
R793
C758R794
R795
Q602
C761
C762C772
C773
C775
C776
R201
R202
R205
R206
R207
R208
R209
IC631
D607A
D406A
D644A
D652A
C650A
C646A
D670A
C606A
C608A
D407A
D659A
D205A
D639A
D639B
R895
R896
R409
R811
14
5 8
121
22
42
4
5 8
1
1 4
8 5
12
3
D
SG
1
23
4
BA01F2F0102 7
WF1PIN 4 OF CN302
WF3PIN 6 OF CN302
WF1PIN 4 OF CN302
WF3PIN 6 OF CN302
WF2PIN 8 OF CN302
WF7PIN 13 OF CN302
WF4PIN 15 OF CN302
WF5PIN 17 OF CN302
WF6PIN 19 OF CN302
Power Supply CBA & Jack CBA Bottom View
BA01F2F01027
Jack CBAPower Supply CBA
NOTE:The voltage for parts in hot circuit is measured usinghot GND as a common terminal.
CAUTION !Fixed voltage (or Auto voltage selectable) power supply circuit is used in this unit.If Main Fuse (F601) is blown , check to see that all components in the power supplycircuit are not defective before you connect the AC plug to the AC power supply.Otherwise it may cause some components in the power supply circuit to fail.
For continued protection against risk of fire, replace only with same type 4 A, 125V fuse.
CAUTION ! :
ATTENTION : Utiliser un fusible de rechange de même type de 4A, 125V.4A/125V
Because a hot chassis ground is present in the power supply circuit, an isolation transformer must be used when repairing.Also, in order to have the ability to increase the input slowly, when troubleshooting this type of power supply circuit, a variable isolation transformer is required.
10-23
TOOL NO.1 2 3 4 5 6 7 8 9 10
C7A3 A3
C7A3/A3
C7A3 A3
/GREEN
/RED
/ORANGE
BA17F4F0103 1 C
C7A3 A3
BA17F4F0103 1 D
2
3
A B C D E F
COLD
HOT
1
BC13
01
BC1930
BC1931
C193
0
C199
0
C1905
C1906
C1104C1106C1108C1110C1112C1114
CN1900CN1901
CN10
03
CN1001
D170
0
D170
2
D1704
D170
6
D193
2
D1933
D196
0
D1961
D197
2
D1973
D120
0
D1201
D120
2
D1990
D1991
D1992
D1300
D130
1
D1701
D170
3
D170
5
D1707
D193
0
D1931
D197
0
D1971
D193
4
D199
4
C1700C1701
C1993
C1994
C1910
C198
2
C1983
C120
6
C130
2
C130
4
IC1930
IC1931
VSEN
J105
8
PROT
J1059
J108
1
DUTY
GND
J109
2
REG
7.5V
J109
5
GND
J110
3
BL-SWJ1107
J1108
J1109
GND
GND
J1120
JS1200
GND
J1003 GND
J1004
J109
3
J1055
VS2
J106
1 VSEN
J106
2
DC12V
J1072
BL-S
W
J109
7
+24V
J110
0
GND
J100
5
SW2
J101
0SW
2J1
011
SW2
J101
2
SW2
J101
3
SW1
J101
4
SW1
J101
5
BST2
J1063
PROT
ECT3
J110
5
STBJ1070
J108
2
J1101
SW2
J102
4 SW2
J1025
J103
2
PROT
6
GND
J104
4
PROT
J106
8
GND
J107
9
GNDJ1084
GNDJ1088
GND
J109
9
GND
J110
4
J1002
REG
7.5V
NH1
J107
4LN
1J1
076GNDJ1077
J108
3
PROT
6J1
048
VS6
J105
4
+24VJ1090
J107
5
VS4J1067
BL-S
WJ1
096
GNDJ1026
GNDJ1028
J106
9
SW1
J107
1
VSEN
J108
0
+24VJ1085
PROTECT3
J1098
SW1
J104
7
J103
3
J103
4PR
OT5
J103
5PR
OT4
J103
6
GND
J104
5
J107
8
J1089
GND
J1051
+24V
J106
4
+24V
J106
5
+24V
J106
6
J107
3
GND
J103
7
REG 7.5V
J1091
J106
0
LN1
J103
9
NH1
J104
0
LN2
J104
1
NH2
J104
2
SW2
J103
8
PROT3
PROT2
PROT1
J1046
J1049
J1050
J1053
J1056
Q1931
Q1932
Q1930
R110
3
R110
6
R111
5
R111
8
R112
7
R113
0
R114
3
R114
5
R114
6
R114
7
R114
8
R115
0
R193
0
R193
1
R193
2
R193
3
R193
4
R193
5R193
6
R193
8
R193
9
R194
9
R196
7
R197
0
R1305
R1937
T1950
GND
J1027
LN2J1030
NH2J1031
J1001
J111
0
PROT
5
PROT
4
J111
1
J111
2
J111
3
PROT
J108
7
FAIL
J108
6
D1203
BA17F4F0103 1 A
BL-ADJ
J1102
R170
4
R170
9
J1020
J1021
PROT5 J102
2PR
OT4
J102
3
J1006
PROT
3
PROT2
J1007
J1008
J1009
CN1100CN1101CN1102
T1100T1101T1102
4VOLUP VOL
DOWN
MENU
CHUP
CHDOWN
POWER
VOL
DOWN VO
LUP
MENU
CH DOWN CH UP
EJECT
STOP
PLAY
POWER
PATTERN
AGING
C108
C151
D107
D151
J101
R108
R109
R111R112R113R114
R115
R151
R152
R153
R154
R155
R156
SW101BSW154SW155 SW103BSW104BSW105BSW106BSW107B
SW151 SW101ASW152SW153SW103ASW104ASW105ASW106ASW107A
CL10
3B
BA17F4F0103 1 BSTD BY
DVDPOWER
GND
C113
J102
D104D105
D106R123
R124
R127
R128
RS102
CL10
3C CL10
1B
STB BY
D108
D109
C101
D101
R101
RS101
CL10
3A
CL10
2B
1
210
11
1
2 14
15
BA17F4F01031
Inverter CBA, Function CBA & IR Sensor CBA Top View
NOTE:The voltage for parts in hot circuit is measured usinghot GND as a common terminal.
Because a hot chassis ground is present in the power supply circuit, an isolation transformer must be used when repairing.Also, in order to have the ability to increase the input slowly, when troubleshooting this type of power supply circuit, a variable isolation transformer is required.
Function CBA Not UsedIR Sensor CBA
Inverter CBA
10-24
2
3
ABCDEF
COLD
HOT
1BC1301
BC1930
BC1931
C1930
C1990
C1905
C1906
C1104 C1106 C1108 C1110 C1112 C1114
CN1900 CN1901
CN1003
CN1001
J1107
D1700
D1702J1014
J1015
D1704D1706
D1932
D1933
D1960
D1961
D1972
D1973
D1200
D1201
D1202
D1990
D1991
D1992
D1300
D1301
D1701
D1703
D1705
D1707
J1030
J1031
D1930
D1931
D1970
D1971
D1934
D1994
C1700 C1701
C1993
C1994
C1910
C1982C1983
C1206
C1302
C1304
J1065
J1064
J1066
IC1930
IC1931
VSEN
J1058
PROT
J1059
J1081
DUTY
GND
J1092 REG 7.5V
J1095
GND
J1103
BL-SW
J1108
J1109
GND
GND
J1120
JS1200
GNDJ1003
GNDJ1004
J1093
J1055
VS2
J1061J1062VSEN
DC12V
J1072
J1070
BL-SW
J1097+24V
J1100
GND
J1005
SW2J1010
SW2J1011
SW2
J1012
SW2
J1013
SW1SW1
BST2
J1063
PROTECT3
J1105
STB
J1082
J1101
SW2J1024J1025
SW2
J1032
PROT6
GND
J1044
PROTJ1068
GND
J1079
GNDJ1084
GNDJ1088GND
J1099
GND J1104
J1002
REG 7.5V
NH1J1074 LN1J1076
GND J1077
J1083
PROT6J1048
VS6J1054
+24V J1090
J1075
VS4J1067
BL-SWJ1096
GNDJ1026
GNDJ1028
J1069
SW1
J1071
VSENJ1080
+24V
PROTECT3
J1098
SW1J1047
J1039
J1040
J1045
J1041
J1042
J1038
J1033
J1034PROT5
J1035PROT4
J1036
GND
J1078
J1089
GND
J1051
+24V
+24V
+24V
J1073
GNDJ1037
REG 7.5V
J1091
J1060
LN1
NH1
LN2
NH2
SW2J1043
J1046PROT3
J1049PROT2
J1050
J1053
J1056PROT1
Q1931
Q1932
Q1930
R1103
R1106
R1115
R1118
R1127
R1130
R1143
R1145
R1146
R1147
R1148
R1150
R1930
R1931
R1932
R1933
R1934
R1935
R1936
R1938
R1939
R1949
R1967R1970
R1305
R1937
T1950
J1085
GND
J1027
LN2
NH2
J1001
J1110
J1111PROT5
J1112PROT4
J1113
PROT
J1087
J1086FAIL
D1203
BA17F4F0103 1A
BL-ADJ
J1102
R1704
R1709
J1020
J1021PROT5
J1022PROT4J1023
J1006
J1007PROT3
J1008PROT2
J1009
CN1100 CN1101 CN1102
T1100 T1101 T1102
4VOLUPVOL
DOWN
MENU
CHUP
CHDOWN
POWER
VOLDOWN
VOLUPMENUCHDOWN
CHUP
EJECT
STOP
PLAY
POWER
PATTERN
AGING
C108
C151D107
D151
J101
R108
R109
R111 R112 R113R114
R115
R151
R152
R153
R154
R155
R156
SW101B SW154 SW155B401WSB301WS SW105B SW106B SW107B
SW151SW101A 351WS251WS SW103A SW104A A701WSA601WSA501WS
CL103B
BA17F4F0103 1BSTD BY
POWERDVD
GND
C113
J102
D104D105
D106
R123
R124
R127 R128
RS102
CL103C
CL101B
STB BY
D108
D109
C101
D101
R101
RS101
CL103A
CL102B
1
210
11
1
214
15
C1931
C1933
C1934
C1702
C1205
C1208
C1209
C1100
C1101
C1102
C1103
C1116
C1117C1118
C1500
C1501
C1119
C1502C1311
C1120
C1121C1122
C1123
C1703
C1704
C1705
C1706
C1707
C1708
C1932
C1935
C1936
C1937
C1938
C1939
C1970
C1981
C1200
C1201
C1202
C1203 C1204
C1207
C1210
C1211
C1105
C1107C1109
C1300
C1301C1303
C1111
C1305
C1113
C1115
Q1970
Q1971
Q1972
Q1201
Q1202
Q1204
Q1301
Q1700 Q1701Q1702
Q1703
R1940
R1941 R1942
R1950
R1952R1951
R1100
R1101
R1102
R1104
R1105
R1107R1108
R1109
R1300
R1301
R1302
R1303
R1110
R1304
R1111
R1112
R1306
R1113
R1307
R1114R1308
R1309
R1116R1117
R1500
R1119
R1501
R1502
R1503
R1504
R1310
R1505
R1506
R1507
R1120
R1508
R1121
R1509
R1122
R1123
R1700
R1124
R1701
R1125
R1702
R1126
R1703
R1510
R1128
R1705
R1511
R1129
R1706
R1512
R1707
R1513
R1708
R1514
R1515
R1131 R1132
R1133
R1134
R1135
R1972
R1973
R1977
R1979
R1980
R1981
R1982
R1986
R1987
R1988
R1200
R1201
R1202R1203
R1204R1205
R1206
R1207
R1208R1209
R1212
R1213
R1214
R1215
R1216
R1220
R1221
R1222
R1223R1225R1226
R1227R1228
R1229
R1516
C1214
C1212
C1213
IC1200
112
13 24
D1505
D1506D1503
D1507
Q1303
Q1203
D1502
D1500
D1501
Q1300
D1504
D1508
C110
C111
C112
C114
C115
R125
R126
C102
C103
C104
R102
R103
R106
H.V. CAUTION
BA17F4F01031
Inverter CBA, Function CBA & IR Sensor CBA Bottom View
Function CBANot Used IR Sensor CBA
Inverter CBA
NOTE:The voltage for parts in hot circuit is measured usinghot GND as a common terminal.
Because a hot chassis ground is present in the power supply circuit, an isolation transformer must be used when repairing.Also, in order to have the ability to increase the input slowly, when troubleshooting this type of power supply circuit, a variable isolation transformer is required.
WAVEFORMS
LC9NWF11-1
Input: NTSC Color Bar Signal (with 1kHz Audio Signal)
WF1 ~ WF7 = Waveforms to be observed atWaveform check points.(Shown in Schematic Diagram.)
CVBS 0.2V 20µs
WF1 Pin 4 of CN302
S-VIDEO-YS-VIDEO-Y 0.2V
WF2 Pin 8 of CN302
20µs
S-VIDEO-CS-VIDEO-C 0.2V
WF3 Pin 6 of CN302
20µs AUDIO 0.1V 0.5ms
WF7 Pin 13 of CN302
VIDEO-PrVIDEO-Pr 0.2V 20µs
Pin 19 of CN302WF6
VIDEO-Pb VIDEO-Pb 0.2V 20µs
Pin 17 of CN302WF5
VIDEO-YVIDEO-Y 0.2V 20µs
Pin 15 of CN302WF4
PL11.0WI12-1
INV
ER
TE
R C
BA
TU
301
TU
NE
R U
NIT
HD
MI-
A
UD
IO(L
)-IN
HD
MI-
A
UD
IO(R
)-IN
AU
DIO
(L)
-OU
T
AU
DIO
(R)
-OU
T
AC
601
AC
CO
RD
PO
WE
R S
UP
PLY
CB
A
DIG
ITA
L M
AIN
CB
A U
NIT
HD
MI-
CO
NN
EC
TO
R-1
HD
MI-
CO
NN
EC
TO
R-2
HD
MI-
CO
NN
EC
TO
R-3
LC
D M
OD
UL
EA
SS
EM
BLY
CL8
011
CN
801
2S
P(L
)-S
P(L
)+
CL8
021
CN
802
2S
P(R
)-S
P(R
)+
SP
801
SP
EA
KE
RL-
CH
SP
802
SP
EA
KE
RR
-CH
CO
MP
ON
EN
T-Y
-IN
CO
MP
ON
EN
T-P
b-IN
CO
MP
ON
EN
T-P
r-IN
CO
MP
ON
EN
T-
AU
DIO
(L)-
IN
CO
MP
ON
EN
T-
AU
DIO
(R)-
IN
VID
EO
-IN
AU
DIO
(L)
-IN
AU
DIO
(R)
-IN
S-V
IDE
O
-IN
CN
201
CN
1001
151
GN
D14
2IN
V+
13V
(NU
)13
3G
ND
124
BAC
KLI
GH
T-A
DJ
115
BA
CK
LIG
HT-
SW
106
PR
OT
EC
T3
97
GN
D8
8LC
D+
13V
79
LCD
+13
V6
10V
GH
511
GN
D4
12P
-ON
+3.
3V3
13LC
D-5
V2
14V
CO
M1
15G
ND
BA
CK
LIG
HT
CN
1100
21
BA
CK
LIG
HT
CN
1101
21
BA
CK
LIG
HT
CN
1102
21
DIG
ITA
L A
UD
IO-O
UT
(C
OA
XIA
L)
JAC
K C
BA
IR S
EN
SO
R C
BA
FU
NC
TIO
N C
BA
CL7
01A
CL7
01C
L701
B1
1S
-VID
EO
-Y-I
N
33
S-V
IDE
O-C
-IN
22
S-V
IDE
O-S
W
44
GN
D5
5V
IDE
O-I
N
77
AU
DIO
(L)-
IN6
6G
ND
88
GN
D9
9A
UD
IO(R
)-IN
CL1
02C
L103
CN
101
11
GN
D
33
AL+
3.3V
22
RE
MO
TE
44
KE
Y-IN
15
5P
-ON
+9V
CL1
02B
CL1
03B
CL1
03A
33
KE
Y-IN
14
4K
EY-
IN2
22
GN
D1
1A
L+3.
3V
CN
1003 11
GN
D10
VC
OM
9G
ND
8LC
D-5
V7
P-O
N+
3.3V
6P
-ON
+3.
3V5
GN
D4
VG
H3
LCD
+13
V2
LCD
+13
V1
GN
D
CN
3902
24G
ND
23LL
V0(
+)
22LL
V0(
-)21
LLV
1(+
)20
LLV
1(-)
19LL
N2(
+)
18LL
V2(
-)17
GN
D16
LLV
CLK
(+)
15LL
VC
LK(-
)14
GN
D13
LLV
3(+
)12
LLV
3(-)
11LL
V4(
+)
10LL
V4(
-)9
LLV
5(+
)8
LLV
5(-)
7G
ND
6T
P5
PO
L4
CP
V3
OE
12
XA
O1
ST
V
CN
3701
CN
301
2319 2115 17 222018161410 126 8 13119751 3 4
1 53 972 4 6 8 10 1412 181611 13 15 17 19 232120
2P
-ON
-H2
AU
DIO
(L)-
OU
TG
ND
AU
DIO
(R)-
OU
TP
RO
TE
CT
3A
MP
(L)-
OU
TG
ND
AM
P(R
)-O
UT
P-O
N-H
1P
-ON
+3V
PR
OT
EC
T1
GN
DP
-ON
+5V
P-O
N+
5VP
RO
TE
CT
2P
-ON
+7V
GN
DG
ND
P-O
N+
3.3V
P-O
N+
3.3V
AL+
3.3V
AL+
3.3V
GN
D22
2424
OE
225
25R
EM
OT
E26
26B
ACK
LIG
HT-
SW
2727
LED
1(N
U)
2828
BAC
KLI
GH
T-A
DJ
2929
VC
OM
-PW
M
CN
3702
CN
302
2319 2115 17 222018161410 126 8 13119751 3 4
1 53 972 4 6 8 10 1412 181611 13 15 17 19 232120
2G
ND
SP
DIF
GN
DV
IDE
O-I
NS
-VID
EO
-SW
S-V
IDE
O-C
-IN
GN
DS
-VID
EO
-Y-I
NG
ND
INP
UT
1A
UD
IO(R
)IN
PU
T0
AU
DIO
(L)
GN
DC
OM
-VID
EO-Y
-ING
ND
COM
-VID
EO-P
b-IN
GN
DCO
M-V
IDEO
-Pr-I
NA
UD
IO-M
UT
ES
DA
SC
LR
ES
ET
22
2424
IF-A
GC
2525
GN
D26
26D
IF-O
UT
127
27G
ND
2828
DIF
-OU
T2
2929
KE
Y-IN
1
CN
602
CN
1901
4H
OT
+15
V3
HO
T-G
ND
2N
U1
+B
3H
OT
+15
V2
HO
T-G
ND
1+
B
CL3
701
CL2
01
CL1
003
CL3
902
CL3
702
US
B J
AC
K
CN
3002
CN
3006
[TY
PE
A]
[TY
PE
B]
[TY
PE
A]
[TY
PE
B]
CN
3005
[TY
PE
A]
[TY
PE
B]
WIRING DIAGRAM
13-1 PL11.0-A_CEX
EXPLODED VIEWS
Cabinet
A42
See Electrical Parts Listfor parts with this mark.
Digital Main CBA Unit
IR Sensor CBA
Power Supply CBA
Function CBA
A1
B27
L19
LCD1B27
A5
A4
L19B1
B18B18
CL3902
L19
L17
L33
A2S6
L33
L33
L33
L33
L23
B11
L19
A8
L23
B24
CL801
CL802
L19
CL3702
CL1003
CL201
X6
B22
L1
B22
L1
S6
L23
S6A12L15
Stand Assembly
B5
X7
A15
A41
L42
SP801
SP802
L34
L19
L1
Inverter CBA
Jack CBA
L17
B34
B34
AC601
B46
CL3701
32PFL3506/F7 (DS1, XA1),32PFL3000/F8 (XA1)
32PFL3506/F7 (DS2, DS3),32PFL3000/F8 (XA2)
32PFL3506/F7 (DS2, DS3), 32PFL3000/F8 (XA2)
13-2 PL11.0PEX
Packing
FRONT
X1
X14 X2
Tape
X12
S17
S3
S1
S7
S4
Packing Tape
Stand Assembly
Stand Screw Kit
S5
CARTON
Packing Tape
X4
X3
S6
Tape
32PFL3506/F7 (XA1)
2011/10/31 14-1 A17F6CA.fm
TYPE A
PARTS LIST[32PFL3506/F7 (Serial No.: DS1), 32PFL3000/F8 (Serial No.: XA1)]
Mechanical Parts
PRODUCT SAFETY NOTE: Products marked with a # have special characteristics important to safety. Before replacing any of these components, read carefully the product safety notice in this service manual. Don't degrade the safety of the product through improper servicing.
NOTE: Parts that are not assigned part numbers (---------) are not available.
Ref. No. Description Part No.
STAND ASSEMBLY A17F6UH 1ESA28472
A1 FRONT CABINET A17F6UH 1EM027428
A2 REAR CABINET A17F6UH 1EM027429
A4 FUNCTION KNOB A17F6UH 1EM225787
A5 KNOB FRAME A17F6UH 1EM225788
A8 JACK HOLDER A01F2UH 1EM124273
A12# RATING LABEL A17F6UH ----------
A15 ENERGY STAR LABEL A91F2UH ----------
A41 SENSOR PLATE A17F6UH 1EM330357A
B1 SHIELD BOX A01F2UH 1EM224323
B5 STAND HOLDER A17F6UH 1EM225789
B11 SPEAKER HOLDER A17F6UH 1EM126056
B18 GASKET A8AF0UH 1EM425861
B22 WALL MOUNT BRACKET A84N0UH 1EM323797
B24 THERMAL SHEET TMS-14-20 12X12 XK10000X4011
B27 CLOTH(10X180XT0.5) L0336JG 0EM408827
CL201 WIRE ASSEMBLY 15PIN FFC 15PIN 140MM WX1A01F4-102
CL801 WIRE ASSEMBLY 2PIN 2PIN/320MM WX1A17F6-301
CL802 WIRE ASSEMBLY 2PIN 2PIN/110MM/CORE WX1A01F2-003
CL1003 WIRE ASSEMBLY 11PIN FFC 11PIN 129MM WX1A01F4-101
CL3701 WIRE ASSEMBLY 29PIN FFC 29PIN 50MM WX1A94F0-101
CL3702 WIRE ASSEMBLY 29PIN FFC 29PIN 50MM WX1A94F0-101
CL3902 WIRE ASSEMBLY 24PIN FFC 24PIN 117.5MM WX1A91F6-102
L1 SCREW P-TIGHT 3X10 BIND HEAD+ GBHP3100
L15 DOUBLE SEMS SCREW M4X10 + BLK FPH34100
L19 ASSEMBLED SCREW ( D9 M3X6 ) A71F0UH 1EM424392B
L23 SCREW TAP TIGHT M3X10 BIND HEAD+BLK NI
GBHS3100
L33 SCREW P-TIGHT 3X14 BIND HEAD+ BLK GBHP3140
L34 SCREW P-TIGHT 3X14 WASHER HEAD+ GCJP3140
L42 SHOULDER SCREW A01Q0UF 1EM328277
LCD1 LCD MODULE UK32AXB
SP801 SPEAKER MAGNETIC S0412F28B DS08130XQ002
SP802 SPEAKER MAGNETIC S0412F28C DS08130XQ003
PACKINGS1 CARTON A17F6UH 1EM434457
S3 STYROFOAM TOP A17F6UH 1EM027431
S4 STYROFOAM BOTTOM A17F6UH 1EM027432A
S5 SET BAG A17F6UH 1EM330877
S6 SERIAL NO. LABEL A01PBUH ----------
S7 STAND BAG A02NBJH 1EM431977
ACCESSORIESSTAND SCREW KIT A17F6UH 1ESA28477
X1 BAG POLYETHYLENE 235X365XT0.03 0EM408420A
X2# OWNERS MANUAL A17F6UH 1EMN28039
X3 REMOTE CONTROL TRANSMITTER YKF259-001
URMT34JHG001
X4 BATTERY R03-B500/01S XB0M451CZB01
X6 QUICK START GUIDE A17F6UH 1EMN28041
X7 REGISTRATION CARD(PHILIPS) A11P4UH 1EMN27321
X12 CABLE MANAGEMENT TIE(BLACK) A01F2UH 1EM431197
X14 ADDENDUM SHEET A17F6UH 1EMN28479
Ref. No. Description Part No.
2011/10/31 14-2 A17F6EL.fm
Electrical Parts
PRODUCT SAFETY NOTE: Products marked with a # have special characteristics important to safety. Before replacing any of these components, read carefully the product safety notice in this service manual. Don't degrade the safety of the product through improper servicing.
NOTES:
1. Parts that are not assigned part numbers (---------) are not available.
2. Tolerance of Capacitors and Resistors are noted with the following symbols.
DIGITAL MAIN CBA UNIT
MPW CBA
POWER SUPPLY CBA
C.....±0.25% D.....±0.5% F.....±1%
G.....±2% J......±5% K.....±10%
M.....±20% N.....±30% Z.....+80/-20%
Ref. No. Description Part No.
DIGITAL MAIN CBA UNIT A17F6MMA-003
Ref. No. Description Part No.
MPW CBAConsists of the following:
A17F6MPW-001
POWER SUPPLY CBA(MPW-A)JACK CBA(MPW-B)
--------------------
Ref. No. Description Part No.
POWER SUPPLY CBA(MPW-A)Consists of the following:
----------
CAPACITORSC201 CHIP CERAMIC CAP.(1608) F Z 0.1µF/25V CHD1EZ30F104
C202 CHIP CERAMIC CAP.(1608) F Z 0.1µF/25V CHD1EZ30F104
C203 CHIP CERAMIC CAP.(1608) F Z 0.1µF/25V CHD1EZ30F104
C204 ELECTROLYTIC CAP. 2.2µF/50V M CE1JMASDL2R2
C207 CHIP CERAMIC CAP.(1608) B K 0.1µF/16V CHD1CK30B104
C210 ELECTROLYTIC CAP. 22µF/50V M CE1JMASDL220
C216 CHIP CERAMIC CAP.(1608) CH J 1000pF/50V CHD1JJ3CH102
C217 CHIP CERAMIC CAP.(1608) B K 0.1µF/16V CHD1CK30B104
C218 CHIP CERAMIC CAP.(1608) B K 1µF/25V CHD1EK30B105
C219 ELECTROLYTIC CAP. 47µF/25V M CE1EMASDL470
C221 CHIP CERAMIC CAP.(1608) B K 0.01µF/50V CHD1JK30B103
C222 ELECTROLYTIC CAP. 470µF/25V M CE1EMASDL471
C223 ELECTROLYTIC CAP. 22µF/50V M CE1JMASDL220
C224 ELECTROLYTIC CAP. 10µF/50V M CE1JMASDL100
C302 CHIP CERAMIC CAP.(1608) F Z 0.1µF/25V CHD1EZ30F104
C303 ELECTROLYTIC CAP. 330µF/10V M CE1AMASDL331
C305 CHIP CERAMIC CAP.(1608) F Z 0.1µF/50V CHD1JZ30F104
C306 ELECTROLYTIC CAP. 1µF/50V M CE1JMASDL1R0
C307 CHIP CERAMIC CAP.(1608) CH J 47pF/50V CHD1JJ3CH470
C308 CHIP CERAMIC CAP.(1608) CH J 47pF/50V CHD1JJ3CH470
C309 CHIP CERAMIC CAP.(1608) B K 0.1µF/25V CHD1EK30B104
C310 CHIP CERAMIC CAP.(1608) CH J 47pF/50V CHD1JJ3CH470
C311 CHIP CERAMIC CAP.(1608) CH J 47pF/50V CHD1JJ3CH470
C601# CAP METALIZED FILM 0.22µF/300V K 3.5MM CT2F224DC004
C602# CAP METALIZED FILM 0.22µF/300V K 3.5MM CT2F224DC004
C605 CAP ELECTROLYTIC 470µF/200V M CA2D471DYG07
C606 POLYESTER FILM CAP. (PB FREE) 0.0015µF/100V J
CA2A152DT018
C607# CERAMIC CAP. 330pF/2KV CA3D331PAN04
C608 POLYESTER FILM CAP. (PB FREE) 0.001µF/100V J
CA2A102DT018
C609 ELECTROLYTIC CAP. 47µF/50V M CE1JMASDL470
C610 ELECTROLYTIC CAP. 100µF/50V M CE1JMASDL101
C611 CAP CERAMIC (AX) 0.1µF/50V/F/Z CA1J104TU062
C613 CAP CERAMIC (AX) 33pF/50V/CH/J CA1J330TU059
C614 CAP CERAMIC (AX) 0.022µF/50V/B/K CA1J223TU061
C615 CAP CERAMIC (AX) 3300pF/50V/B/K CA1J332TU061
C631 ELECTROLYTIC CAP. 1000µF/25V M CE1EMZNDL102
C632 ELECTROLYTIC CAP. 220µF/25V M CE1EMASDL221
C633 CAP ALUMINUM ELECTOLYTIC 2200µF/6.3V M
CE0KMZNDL222
C637 CERAMIC CAP. 1500pF/2KV CA3D152PAN04
C638 ELECTROLYTIC CAP. 220µF/50V M CE1JMASDL221
C639 ELECTROLYTIC CAP. 1000µF/35V M CE1GMZADL102
C640 ELECTROLYTIC CAP. 1µF/50V M CE1JMASDL1R0
C642 ELECTROLYTIC CAP. 1µF/50V M CE1JMASDL1R0
C643 CHIP CERAMIC CAP.(1608) B K 1µF/10V CHD1AK30B105
C644 ELECTROLYTIC CAP 3300µF/16V M CE1CMZNDL332
C645 CAP ALUMINUM ELECTOLYTIC 2200µF/6.3V M
CE0KMZNDL222
C646 POLYESTER FILM CAP. (PB FREE) 0.0022µF/100V J
CA2A222DT018
C648 ELECTROLYTIC CAP. 100µF/10V M CE1AMASDL101
C649 CHIP CERAMIC CAP.(1608) B K 0.1µF/25V CHD1EK30B104
C650 POLYESTER FILM CAP. (PB FREE) 0.022µF/100V J
CA2A223DT018
C652 ELECTROLYTIC CAP. 1000µF/6.3V M CE0KMASDL102
C653 ELECTROLYTIC CAP. 220µF/10V M CE1AMASDL221
C654 ELECTROLYTIC CAP. 220µF/10V M CE1AMASDL221
C656 ELECTROLYTIC CAP. 100µF/16V M CE1CMASDL101
C657 ELECTROLYTIC CAP. 22µF/50V M CE1JMASDL220
C676 ELECTROLYTIC CAP. 2.2µF/50V M CE1JMASDL2R2
C681 CHIP CERAMIC CAP.(1608) F Z 0.1µF/25V CHD1EZ30F104
C682 CHIP CERAMIC CAP.(1608) F Z 0.1µF/25V CHD1EZ30F104
C683 CHIP CERAMIC CAP.(1608) F Z 0.1µF/25V CHD1EZ30F104
C684 CHIP CERAMIC CAP.(1608) F Z 0.1µF/25V CHD1EZ30F104
C691# SAFTY CAP. 1000pF/250V KX CA2E102MR101
C693# SAFTY CAP. 1000pF/250V KX CA2E102MR101
C723 CHIP CERAMIC CAP.(1608) B K 2.2µF/10V CHD1AK30B225
C724 CHIP CERAMIC CAP.(1608) B K 2.2µF/10V CHD1AK30B225
C731 CHIP CERAMIC CAP. CH J 39pF/50V CHD1JJ3CH390
C732 CHIP CERAMIC CAP. CH J 39pF/50V CHD1JJ3CH390
C733 CHIP CERAMIC CAP. CH J 39pF/50V CHD1JJ3CH390
C734 RES CHIP 1608 1/10W 0 Ω RRXA000HH014
C735 RES CHIP 1608 1/10W 0 Ω RRXA000HH014
C736 RES CHIP 1608 1/10W 0 Ω RRXA000HH014
C743 CHIP CERAMIC CAP.(1608) B K 2.2µF/10V CHD1AK30B225
C744 CHIP CERAMIC CAP.(1608) B K 2.2µF/10V CHD1AK30B225
C771 ELECTROLYTIC CAP. 100µF/16V M CE1CMASDL101
C772 CHIP CERAMIC CAP.(1608) F Z 0.1µF/25V CHD1EZ30F104
C775 CHIP CERAMIC CAP.(1608) CH J 100pF/50V CHD1JJ3CH101
C776 CHIP CERAMIC CAP.(1608) CH J 100pF/50V CHD1JJ3CH101
C801 CHIP CERAMIC CAP.(1608) B K 1µF/25V CHD1EK30B105
Ref. No. Description Part No.
2011/10/31 14-3 A17F6EL.fm
C803 CHIP CERAMIC CAP.(1608) B K 0.47µF/25V CHD1EK30B474
C804 CHIP CERAMIC CAP.(1608) B K 0.1µF/25V CHD1EK30B104
C805 CHIP CERAMIC CAP.(1608) CH J 1000pF/50V CHD1JJ3CH102
C806 CHIP CERAMIC CAP.(1608) B K 0.47µF/25V CHD1EK30B474
C807 CHIP CERAMIC CAP.(1608) B K 0.1µF/25V CHD1EK30B104
C808 CHIP CERAMIC CAP.(1608) CH J 1000pF/50V CHD1JJ3CH102
C809 CHIP CERAMIC CAP.(1608) B K 1µF/25V CHD1EK30B105
C810 CHIP CERAMIC CAP.(1608) B K 1µF/25V CHD1EK30B105
C814 CHIP CERAMIC CAP.(1608) B K 1µF/25V CHD1EK30B105
C815 CHIP CERAMIC CAP.(1608) B K 1µF/25V CHD1EK30B105
C816 ELECTROLYTIC CAP. 10µF/50V M CE1JMASDL100
C817 CHIP CERAMIC CAP.(1608) B K 1µF/25V CHD1EK30B105
C818 CHIP CERAMIC CAP.(1608) B K 0.1µF/25V CHD1EK30B104
C819 ELECTROLYTIC CAP. 10µF/50V M CE1JMASDL100
C820 CHIP CERAMIC CAP.(1608) B K 0.47µF/25V CHD1EK30B474
C821 CHIP CERAMIC CAP.(1608) B K 0.1µF/25V CHD1EK30B104
C822 CHIP CERAMIC CAP.(1608) CH J 1000pF/50V CHD1JJ3CH102
C823 ELECTROLYTIC CAP. 1000µF/25V M CE1EMZNDL102
C824 CHIP CERAMIC CAP.(1608) B K 0.47µF/25V CHD1EK30B474
C825 CHIP CERAMIC CAP.(1608) B K 0.1µF/25V CHD1EK30B104
C826 CHIP CERAMIC CAP.(1608) CH J 1000pF/50V CHD1JJ3CH102
C827 ELECTROLYTIC CAP. 10µF/50V M CE1JMASDL100
C828 CHIP CERAMIC CAP.(1608) B K 1µF/25V CHD1EK30B105
C829 CHIP CERAMIC CAP.(1608) B K 1µF/25V CHD1EK30B105
C831 ELECTROLYTIC CAP. 10µF/50V M CE1JMASDL100
C834 CHIP CERAMIC CAP.(1608) B K 0.47µF/16V CHD1CK30B474
C835 CHIP CERAMIC CAP.(1608) CH J 1000pF/50V CHD1JJ3CH102
C836 CHIP CERAMIC CAP.(1608) B K 0.47µF/16V CHD1CK30B474
C837 CHIP CERAMIC CAP.(1608) CH J 1000pF/50V CHD1JJ3CH102
C838 CHIP CERAMIC CAP.(1608) CH J 470pF/50V CHD1JJ3CH471
C839 CHIP CERAMIC CAP.(1608) CH J 470pF/50V CHD1JJ3CH471
C841 CHIP CERAMIC CAP. F Z 1µF/10V CHD1AZ30F105
C842 CHIP CERAMIC CAP. F Z 1µF/10V CHD1AZ30F105
C843 CHIP CERAMIC CAP.(1608) B K 0.01µF/50V CHD1JK30B103
C844 ELECTROLYTIC CAP. 10µF/50V M CE1JMASDL100
C845 CHIP CERAMIC CAP.(1608) CH J 470pF/50V CHD1JJ3CH471
C846 CHIP CERAMIC CAP.(1608) CH J 470pF/50V CHD1JJ3CH471
C871 CHIP CERAMIC CAP.(1608) B K 3300pF/50V CHD1JK30B332
C872 CHIP CERAMIC CAP.(1608) B K 3300pF/50V CHD1JK30B332
C873 CHIP CERAMIC CAP.(1608) B K 2.2µF/10V CHD1AK30B225
C874 CHIP CERAMIC CAP.(1608) B K 2.2µF/10V CHD1AK30B225
C875 CHIP CERAMIC CAP.(1608) CH J 100pF/50V CHD1JJ3CH101
C876 CHIP CERAMIC CAP.(1608) CH J 100pF/50V CHD1JJ3CH101
C877 CHIP CERAMIC CAP.(1608) B K 6800pF/50V CHD1JK30B682
C878 CHIP CERAMIC CAP.(1608) B K 6800pF/50V CHD1JK30B682
C879 CHIP CERAMIC CAP.(1608) F Z 0.1µF/25V CHD1EZ30F104
C880 ELECTROLYTIC CAP. 100µF/16V M CE1CMASDL101
C882 CHIP CERAMIC CAP.(1608) B K 2.2µF/10V CHD1AK30B225
C883 CHIP CERAMIC CAP.(1608) B K 2.2µF/10V CHD1AK30B225
C884 CHIP CERAMIC CAP.(1608) B K 2.2µF/10V CHD1AK30B225
C885 CHIP CERAMIC CAP.(1608) B K 2.2µF/10V CHD1AK30B225
CONNECTORSCN101 CONNECTOR PRINT OSU B5B-PH-K-S
(LF)(SN)J3PHC05JG029
CN201 FFC CONNECTOR 15P IMSA-9615S-15A-PP-A JC96J15ER007
CN301 FFC CONNECTOR IMSA-9615S-29A-PP-A JC96J29ER007
CN302 FFC CONNECTOR IMSA-9615S-29A-PP-A JC96J29ER007
CN602# WIRE ASSEMBLY 3PIN 3PIN 145MM R/B/W WX1A01F0-201
CN801 PH CONNECTOR TOP 2P B2B-PH-K-S (LF)(SN)
J3PHC02JG029
CN802 PH CONNECTOR TOP 2P B2B-PH-K-S (LF)(SN)
J3PHC02JG029
Ref. No. Description Part No.
DIODESD202 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133
D203 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133
D204 IC SHUNT REGULATOR KIA431-AT/P NSZBA0TJY036
D205 DIODE ZENER 33BSA-T26 NDTA033BST26
D206 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133
D207 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133
D208 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133
D209 DIODE ZENER 39BSB-T26 NDTB039BST26
D210 DIODE ZENER 5V1BSB-T26 NDTB5R1BST26
D211 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133
D401 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133
D404 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133
D405 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133
D406 DIODE ZENER 27BSB-T26 NDTB027BST26
D407 DIODE ZENER 10BSB-T26 NDTB010BST26
D409 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133
D410 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133
D411 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133
D412 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133
D413 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133
D414 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133
D415 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133
D417 DIODE ZENER 3V9BSB-T26 NDTB3R9BST26
D418 DIODE ZENER 3V9BSB-T26 NDTB3R9BST26
D419 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133
D420 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133
D421 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133
D601# DIODE GENERAL PURPOSE 1N5406-BU NDLZ1N5406BU
D602# DIODE GENERAL PURPOSE 1N5406-BU NDLZ1N5406BU
D603# DIODE GENERAL PURPOSE 1N5406-BU NDLZ1N5406BU
D604# DIODE GENERAL PURPOSE 1N5406-BU NDLZ1N5406BU
D607 DIODE ZENER 11BSB-T26 NDTB011BST26
D608# DIODE ZENER 27BSB-T26 NDTB027BST26
D609# DIODE ZENER 27BSB-T26 NDTB027BST26
D610 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133
D612# DIODE FR104-B NDLZ000FR104
D613 DIODE FR104-B NDLZ000FR104
D614# DIODE FAST RECOVERY FR103-B/P NDWZ0FR103BP
D615# DIODE ZENER 39BSB-T26 NDTB039BST26
D616# DIODE ZENER 27BSB-T26 NDTB027BST26
D617 DIODE FAST RECOVERY FR103-B/P NDWZ0FR103BP
D619 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133
D621 DIODE ZENER 1ZB200-YBB NDWZ01ZB200Y
D622# DIODE FAST RECOVERY FR103-B/P NDWZ0FR103BP
D631 DIODE SCHOTTKY BARRIER SB2150BD NDWZ00SB2150
D632 DIODE FR104-B NDLZ000FR104
D633 DIODE FAST RECOVERY FR151-B/P NDWZ0FR151BP
D635 DIODE ZENER 24BSB-T26 NDTB024BST26
D638 DIODE FR154 NDLZ000FR154
D639 DIODE ZENER 1ZB43BB NDWZ0001ZB43
D641 SCHOTTKY BARRIER DIODE SB390 NDWZ000SB390
D642 SCHOTTKY BARRIER DIODE SB390 NDWZ000SB390
D643 DIODE FR104-B NDLZ000FR104
D644 DIODE ZENER 7V5BSB-T26 NDTB7R5BST26
D645 SHUNT REGULATOR KIA431B-AT/P NSZBA0TJY038
D646 DIODE SCHOTTKY SB360BH NDWZ000SB360
D647 SCHOTTKY BARRIER DIODE SB140 NDWZ000SB140
D648 WIRE COPPER 6111-06003-0120 XZ40C0SHG002
D652 DIODE ZENER 5V6BSB-T26 NDTB5R6BST26
D653 IC SHUNT REGULATOR KIA431-AT/PF5 NSZBB0TJY036
D654 WIRE COPPER 6111-06003-0120 XZ40C0SHG002
Ref. No. Description Part No.
2011/10/31 14-4 A17F6EL.fm
D655 RECTIFIER DIODE 1N4005 NDQZ001N4005
D657 DIODE ZENER 33BSB-T26 NDTB033BST26
D658 DIODE ZENER 3V3BSB-T26 NDTB3R3BST26
D659 DIODE ZENER 5V6BSA-T26 NDTA5R6BST26
D660 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133
D661 DIODE FR154 NDLZ000FR154
D662 DIODE FR154 NDLZ000FR154
D664 DIODE ZENER 4V7BSB-T26 NDTB4R7BST26
D665 WIRE COPPER 6111-06003-0120 XZ40C0SHG002
D666 IC SHUNT REGULATOR KIA431-AT/P NSZBA0TJY036
D670 DIODE ZENER 10BSB-T26 NDTB010BST26
D671 WIRE COPPER 6111-06003-0120 XZ40C0SHG002
D676 WIRE COPPER 6111-06003-0120 XZ40C0SHG002
D801 DIODE ZENER 20BSB-T26 NDTB020BST26
D802 DIODE ZENER 20BSB-T26 NDTB020BST26
D803 DIODE ZENER 20BSB-T26 NDTB020BST26
D804 DIODE ZENER 20BSB-T26 NDTB020BST26
ICSIC201 IC TL3472CDR NSZBA0TTY115
IC601# IC PHOTOCOUPLER TLP781F(D4-FUNBLL F) QPEL781FBLLF
IC602# IC SWITING FA5571N-D1-TE1/SOP-8 QSCA0T0FD003
IC631 IC REGULATOR MM3123DPRE QSCA0T0MM108
IC771 IC SWITCHING TC4052BF(ELNF) QSZBA0TTS162
IC801 IC D-CLASS POWER AMPLIFER R2A15124SP-W00T
QSCA0T0HT006
IC871 IC OP AMP NJM4558M(TE1)-#ZZZB QSZBA0TJR089
COILSL301 WIRE COPPER 6111-06003-0120 XZ40C0SHG002
L302 CHIP INDUCTOR LK1608R22K-T LLACKB3TUR22
L303 CHIP INDUCTOR LK1608R22K-T LLACKB3TUR22
L601# COIL LINE FILTER ST0908ET28V-016 LLEG0Z0Y2008
L602# COIL LINE FILTER ST0908ET28V-016 LLEG0Z0Y2008
L801 RADIAL LEAD INDUCTORS 33µH LLARKGQTU330
L802 RADIAL LEAD INDUCTORS 33µH LLARKGQTU330
L803 RADIAL LEAD INDUCTORS 33µH LLARKGQTU330
L804 RADIAL LEAD INDUCTORS 33µH LLARKGQTU330
L871 WIRE COPPER 6111-06003-0120 XZ40C0SHG002
TRANSISTORSQ201 TRANSISTOR KTA1267-GR-AT/P NQS1KTA1267P
Q202 TRANSISTOR KTC3198-Y-AT/P NQSYKTC3198P
Q203 TRANSISTOR KTC3198-Y-AT/P NQSYKTC3198P
Q204 TRANSISTOR KTA1267-GR-AT/P NQS1KTA1267P
Q205 TRANSISTOR KTC3198-Y-AT/P NQSYKTC3198P
Q207 TRANSISTOR KTA1267-GR-AT/P NQS1KTA1267P
Q208 TRANSISTOR KTC3198-Y-AT/P NQSYKTC3198P
Q209 TRANSISTOR 2SC2120-Y(TE2 F T) QQSY2SC2120F
Q210 TRANSISTOR KTC3198-Y-AT/P NQSYKTC3198P
Q211 TRANSISTOR KTC3198-Y-AT/P NQSYKTC3198P
Q212 TRANSISTOR KTC3198-Y-AT/P NQSYKTC3198P
Q213 TRANSISTOR 2SA950-O (TE2 F T) QQS002SA950F
Q401 TRANSISTOR KTC3198-Y-AT/P NQSYKTC3198P
Q402 TRANSISTOR KTC3198-Y-AT/P NQSYKTC3198P
Q601# FET MOS TK5A50D(FUNAI QEWZTK5A50DQ
Q602# FET POWER MOS SMD KHB1D0N60D-RTF/PMC
NF1ZKHB1D0N6
Q603 TRANSISTOR KTC3198-Y-AT/P NQSYKTC3198P
Q604 TRANSISTOR KTA1267-GR-AT/P NQS1KTA1267P
Q631 TRANSISTOR KTC3198-Y-AT/P NQSYKTC3198P
Q634 TRANSISTOR KTC3199-GR-AT/P NQS4KTC3199P
Q635 TRANSISTOR 2SC2120-Y(TE2 F T) QQSY2SC2120F
Q636 TRANSISTOR 2SA950-O (TE2 F T) QQS002SA950F
Q637 NPN TRANSISTOR POWER 2SC4881F HFE MAX320
QQWZ2SC4881F
Ref. No. Description Part No.
Q638 TRANSISTOR KTA1267-GR-AT/P NQS1KTA1267P
Q639 TRANSISTOR KTC3199-GR-AT/P NQS4KTC3199P
Q640 TRANSISTOR 2SC2120-Y(TE2 F T) QQSY2SC2120F
Q641 TRANSISTOR 2SC2120-Y(TE2 F T) QQSY2SC2120F
Q642 TRANSISTOR KTC3198-Y-AT/P NQSYKTC3198P
Q643 TRANSISTOR 2SA950-O (TE2 F T) QQS002SA950F
Q771 TRANSISTOR KTC3198-Y-AT/P NQSYKTC3198P
Q772 TRANSISTOR KTC3198-Y-AT/P NQSYKTC3198P
Q801 TRANSISTOR KTC3198-Y-AT/P NQSYKTC3198P
Q841 TRANSISTOR KTC3198-Y-AT/P NQSYKTC3198P
Q871 TRANSISTOR KTC3198-Y-AT/P NQSYKTC3198P
Q872 TRANSISTOR KTC3198-Y-AT/P NQSYKTC3198P
Q873 TRANSISTOR KTC3198-Y-AT/P NQSYKTC3198P
Q874 TRANSISTOR KTA1267-GR-AT/P NQS1KTA1267P
RESISTORSR201 RES CHIP 1608 1/10W J 100k Ω RRXA104HH013
R202 RES CHIP 1608 1/10W J 1.0k Ω RRXA102HH013
R204 RES CARBON FILM T 1/4W J 1.0k Ω RCX4102T1001
R206 RES CHIP 1608 1/10W J 1.0k Ω RRXA102HH013
R207 RES CHIP 1608 1/10W J 100k Ω RRXA104HH013
R208 RES CHIP 1608 1/10W J 1.0 Ω RRXA1R0HH013
R209 RES CHIP 1608 1/10W 0 Ω RRXA000HH014
R210 RES CARBON FILM T 1/4W J 10 Ω RCX4100T1001
R211 RES CHIP 1608 1/10W 0 Ω RRXA000HH014
R212 RES CARBON FILM T 1/4W J 10 Ω RCX4100T1001
R213 RES CHIP 1608 1/10W J 100k Ω RRXA104HH013
R214 RES CHIP 1608 1/10W 0 Ω RRXA000HH014
R216 RES CHIP 1608 1/10W J 10k Ω RRXA103HH013
R217 RES CHIP 1608 1/10W J 1.5k Ω RRXA152HH013
R218 RES CHIP 1608 1/10W J 10k Ω RRXA103HH013
R219 RES CHIP 1608 1/10W J 15k Ω RRXA153HH013
R220 RES CHIP 1608 1/10W J 1.0k Ω RRXA102HH013
R223 RES CARBON FILM T 1/4W J 3.3k Ω RCX4332T1001
R224 RES CARBON FILM T 1/4W J 27k Ω RCX4273T1001
R225 RES CHIP 1608 1/10W J 22k Ω RRXA223HH013
R226 RES CHIP 1608 1/10W J 22k Ω RRXA223HH013
R227 RES. CARBON FILM J 1/2W J 5.6 Ω RCX25R6T1003
R228 RES CARBON FILM T 1/4W J 3.3k Ω RCX4332T1001
R229 RES CARBON FILM T 1/4W J 3.3k Ω RCX4332T1001
R231 RES CHIP 1608 1/10W J 1.5k Ω RRXA152HH013
R232 RES CHIP 1608 1/10W F 9.10k Ω RTW9101HH008
R233 RES CHIP 1608 1/10W 0 Ω RRXA000HH014
R234 RES CHIP 1608 1/10W F 2.20k Ω RTW2201HH008
R235 RES CARBON FILM T 1/4W J 68 Ω RCX4680T1001
R236 WIRE COPPER 6111-06003-0120 XZ40C0SHG002
R237 RES CARBON FILM T 1/4W J 8.2k Ω RCX4822T1001
R238 RES CARBON FILM T 1/4W J 680 Ω RCX4681T1001
R240 RES CARBON FILM T 1/4W J 47k Ω RCX4473T1001
R241 RES CHIP 1608 1/10W J 22k Ω RRXA223HH013
R242 RES CARBON FILM T 1/4W J 12k Ω RCX4123T1001
R243 RES CARBON FILM T 1/4W J 120 Ω RCX4121T1001
R245 RES CARBON FILM T 1/4W J 8.2k Ω RCX4822T1001
R247 RES. CARBON FILM J 1/2W J 5.6 Ω RCX25R6T1003
R248 RES CHIP 1608 1/10W J 10k Ω RRXA103HH013
R250 METAL OXIDE FILM RES. 1W J 8.2 Ω RN018R2ZU001
R253 RES. CARBON FILM J 1/2W J 5.6 Ω RCX25R6T1003
R302 RES CHIP 1608 1/10W 0 Ω RRXA000HH014
R303 RES CHIP 1608 1/10W 0 Ω RRXA000HH014
R306 RES CHIP 1608 1/10W 0 Ω RRXA000HH014
R307 RES CHIP 1608 1/10W 0 Ω RRXA000HH014
R308 RES CHIP 1608 1/10W J 82 Ω RRXA820HH013
R309 RES CHIP 1608 1/10W J 82 Ω RRXA820HH013
Ref. No. Description Part No.
2011/10/31 14-5 A17F6EL.fm
R310 RES CHIP 1608 1/10W 0 Ω RRXA000HH014
R401 RES CHIP 1608 1/10W J 22k Ω RRXA223HH013
R402 RES CARBON FILM T 1/4W J 22k Ω RCX4223T1001
R403 RES CHIP 1608 1/10W J 47k Ω RRXA473HH013
R404 RES CHIP 1608 1/10W J 22k Ω RRXA223HH013
R405 RES CARBON FILM T 1/4W J 47k Ω RCX4473T1001
R407 RES CARBON FILM T 1/4W J 22k Ω RCX4223T1001
R408 RES CHIP 1608 1/10W J 10k Ω RRXA103HH013
R410 RES CHIP 1608 1/10W F 39.0k Ω RTW3902HH008
R411 RES CHIP 1608 1/10W F 47.0k Ω RTW4702HH008
R412 RES CHIP 1608 1/10W J 3.3k Ω RRXA332HH013
R601# GLASS GLAZE RES. 1/2W J 2.7M Ω RXX2JZLZ0275
R603# CEMENT RESISTOR 5W J 2.2 Ω H 10MM RW052R2PAK10
R604 RES CHIP 3216 1/4W J 2.7M Ω RRX4275HH034
R605# CEMENT RESISTOR 5W J 2.2 Ω H 10MM RW052R2PAK10
R606 RES CARBON FILM T 1/4W J 47k Ω RCX4473T1001
R607 RES CHIP 3216 1/4W J 2.7M Ω RRX4275HH034
R609 RES CARBON FILM T 1/4W J 180 Ω RCX4181T1001
R610 RES CARBON FILM T 1/4W J 10 Ω RCX4100T1001
R611 RES CARBON FILM T 1/4W J 4.7k Ω RCX4472T1001
R612 RES CARBON FILM T 1/4W J 68 Ω RCX4680T1001
R613# METAL OXIDE FILM RES. 2W J 0.47 Ω RN02R47ZU001
R617 RES CARBON FILM T 1/4W J 100k Ω RCX4104T1001
R618 WIRE COPPER 6111-06003-0120 XZ40C0SHG002
R619 WIRE COPPER 6111-06003-0120 XZ40C0SHG002
R622 RES CARBON FILM T 1/4W J 1.2k Ω RCX4122T1001
R623 RES CARBON FILM T 1/4W J 10k Ω RCX4103T1001
R624 RES CARBON FILM T 1/4W J 10k Ω RCX4103T1001
R626 RES CARBON FILM T 1/4W J 15k Ω RCX4153T1001
R635 RES. CARBON FILM J 1/2W J 3.9 Ω RCX23R9T1003
R636 RES. CARBON FILM J 1/2W J 3.9 Ω RCX23R9T1003
R637 RES CARBON FILM T 1/4W G 3.3k Ω RCX4332T1002
R638 WIRE COPPER 6111-06003-0120 XZ40C0SHG002
R639 RES CARBON FILM T 1/4W G 39k Ω RCX4393T1002
R641 RES CHIP 1608 1/10W D 1.10k Ω RTW1101HH007
R642 RES CHIP 1608 1/10W D 10.0k Ω RTW1002HH007
R643 RES CHIP 1608 1/10W D 10.0k Ω RTW1002HH007
R644 RES CHIP 1608 1/10W F 1.50k Ω RTW1501HH008
R646 RES CARBON FILM T 1/4W J 180 Ω RCX4181T1001
R647 RES CHIP 1608 1/10W J 1.0k Ω RRXA102HH013
R648 RES CHIP 1608 1/10W F 1.00k Ω RTW1001HH008
R649 RES CARBON FILM T 1/4W J 2.7k Ω RCX4272T1001
R650 RES CARBON FILM T 1/4W J 2.7k Ω RCX4272T1001
R651 RES CHIP 1608 1/10W J 1.0 Ω RRXA1R0HH013
R652 RES CHIP 1608 1/10W F 24.0k Ω RTW2402HH008
R653 WIRE COPPER 6111-06003-0120 XZ40C0SHG002
R654 RES CHIP 1608 1/10W J 10k Ω RRXA103HH013
R655 RES CARBON FILM T 1/4W G 27k Ω RCX4273T1002
R657 RES CARBON FILM T 1/4W J 1.0 Ω RCX41R0T1001
R658 RES CARBON FILM T 1/4W J 10k Ω RCX4103T1001
R659 RES CHIP 1608 1/10W J 47k Ω RRXA473HH013
R660 RES CARBON FILM T 1/4W J 820 Ω RCX4821T1001
R661 RES. CARBON FILM J 1/2W J 390 Ω RCX2391T1003
R662 RES CARBON FILM T 1/4W J 15 Ω RCX4150T1001
R663 RES CARBON FILM T 1/4W J 820 Ω RCX4821T1001
R664 RES CARBON FILM T 1/4W J 820 Ω RCX4821T1001
R665 WIRE COPPER 6111-06003-0120 XZ40C0SHG002
R667 WIRE COPPER 6111-06003-0120 XZ40C0SHG002
R668 RES CHIP 1608 1/10W F 10.0k Ω RTW1002HH008
R672 WIRE COPPER 6111-06003-0120 XZ40C0SHG002
R673 RES CARBON FILM T 1/4W J 22k Ω RCX4223T1001
R674 RES CARBON FILM T 1/4W J 1.0k Ω RCX4102T1001
R675 RES CHIP 1608 1/10W J 10k Ω RRXA103HH013
Ref. No. Description Part No.
R676 RES CHIP 1608 1/10W J 47k Ω RRXA473HH013
R677 RES CARBON FILM T 1/4W J 270 Ω RCX4271T1001
R678 RES CARBON FILM T 1/4W J 10 Ω RCX4100T1001
R679 RES CHIP 1608 1/10W F 3.60k Ω RTW3601HH008
R680 RES CHIP 1608 1/10W F 10.0k Ω RTW1002HH008
R682 RES CARBON FILM T 1/4W J 2.7 Ω RCX42R7T1001
R683 RES CARBON FILM T 1/4W J 2.7 Ω RCX42R7T1001
R685 RES CARBON FILM T 1/4W J 22 Ω RCX4220T1001
R686 RES CARBON FILM T 1/4W J 680 Ω RCX4681T1001
R687 RES CARBON FILM T 1/4W J 10 Ω RCX4100T1001
R688 RES CARBON FILM T 1/4W J 10 Ω RCX4100T1001
R689 RES CARBON FILM T 1/4W J 560 Ω RCX4561T1001
R691 RES CARBON FILM T 1/4W J 1.8 Ω RCX41R8T1001
R693 RES CARBON FILM T 1/4W J 1.5 Ω RCX41R5T1001
R696 METAL OXIDE FILM RES. 1W J 2.7 Ω RN012R7ZU001
R697 METAL OXIDE FILM RES. 1W J 2.7 Ω RN012R7ZU001
R698 RES CARBON FILM T 1/4W J 2.2 Ω RCX42R2T1001
R723 RES CHIP 1608 1/10W J 15k Ω RRXA153HH013
R724 RES CHIP 1608 1/10W J 15k Ω RRXA153HH013
R725 RES CHIP 1608 1/10W J 39k Ω RRXA393HH013
R726 RES CHIP 1608 1/10W J 39k Ω RRXA393HH013
R731 RES CHIP 1608 1/10W J 75 Ω RRXA750HH013
R732 RES CHIP 1608 1/10W J 75 Ω RRXA750HH013
R733 RES CHIP 1608 1/10W J 75 Ω RRXA750HH013
R734 RES CHIP 1608 1/10W J 10 Ω RRXA100HH013
R735 RES CHIP 1608 1/10W J 10 Ω RRXA100HH013
R736 RES CHIP 1608 1/10W J 10 Ω RRXA100HH013
R743 RES CHIP 1608 1/10W J 15k Ω RRXA153HH013
R744 RES CHIP 1608 1/10W J 15k Ω RRXA153HH013
R745 RES CHIP 1608 1/10W J 39k Ω RRXA393HH013
R746 RES CHIP 1608 1/10W J 39k Ω RRXA393HH013
R763 RES CARBON FILM T 1/4W J 10k Ω RCX4103T1001
R771 WIRE COPPER 6111-06003-0120 XZ40C0SHG002
R772 RES CHIP 1608 1/10W J 10k Ω RRXA103HH013
R773 RES CHIP 1608 1/10W J 10k Ω RRXA103HH013
R774 RES CHIP 1608 1/10W J 10k Ω RRXA103HH013
R775 RES CHIP 1608 1/10W J 10k Ω RRXA103HH013
R776 RES CHIP 1608 1/10W J 100k Ω RRXA104HH013
R777 RES CHIP 1608 1/10W J 100k Ω RRXA104HH013
R778 RES CHIP 1608 1/10W J 100k Ω RRXA104HH013
R779 RES CHIP 1608 1/10W J 100k Ω RRXA104HH013
R801 RES CHIP 1608 1/10W 0 Ω RRXA000HH014
R802 RES CHIP 1608 1/10W J 22k Ω RRXA223HH013
R807 RES CHIP 1608 1/10W 0 Ω RRXA000HH014
R809 RES CHIP 1608 1/10W J 4.7k Ω RRXA472HH013
R810 RES CHIP 1608 1/10W 0 Ω RRXA000HH014
R811 RES CHIP 1608 1/10W 0 Ω RRXA000HH014
R812 RES CHIP 1608 1/10W 0 Ω RRXA000HH014
R813 RES CHIP 1608 1/10W J 7.5k Ω RRXA752HH013
R814 RES CHIP 1608 1/10W J 47k Ω RRXA473HH013
R815 RES CHIP 1608 1/10W J 7.5k Ω RRXA752HH013
R816 RES CHIP 1608 1/10W J 47k Ω RRXA473HH013
R817 RES CHIP 1608 1/10W J 10k Ω RRXA103HH013
R818 RES CHIP 1608 1/10W J 10k Ω RRXA103HH013
R819 RES CARBON FILM T 1/4W J 22k Ω RCX4223T1001
R820 RES CHIP 1608 1/10W J 47k Ω RRXA473HH013
R842 RES CHIP 1608 1/10W 0 Ω RRXA000HH014
R843 RES CHIP 1608 1/10W J 110 Ω RRXA111HH013
R844 RES CHIP 1608 1/10W J 220 Ω RRXA221HH013
R846 RES CHIP 1608 1/10W J 100 Ω RRXA101HH013
R847 RES CHIP 1608 1/10W J 4.7k Ω RRXA472HH013
R848 RES CHIP 1608 1/10W J 4.7k Ω RRXA472HH013
R871 RES CHIP 1608 1/10W J 560 Ω RRXA561HH013
Ref. No. Description Part No.
2011/10/31 14-6 A17F6EL.fm
JACK CBA
INVERTER ASSEMBLY
INVERTER CBA
R872 RES CHIP 1608 1/10W J 560 Ω RRXA561HH013
R873 RES CHIP 1608 1/10W J 100k Ω RRXA104HH013
R874 RES CHIP 1608 1/10W J 100k Ω RRXA104HH013
R875 RES CHIP 1608 1/10W 0 Ω RRXA000HH014
R876 RES CHIP 1608 1/10W 0 Ω RRXA000HH014
R877 RES CHIP 1608 1/10W J 1.0k Ω RRXA102HH013
R878 RES CARBON FILM T 1/4W J 1.0k Ω RCX4102T1001
R879 RES CHIP 1608 1/10W J 47k Ω RRXA473HH013
R880 RES CHIP 1608 1/10W J 47k Ω RRXA473HH013
R881 RES CHIP 1608 1/10W J 100 Ω RRXA101HH013
R882 RES CHIP 1608 1/10W J 100 Ω RRXA101HH013
R883 RES CHIP 1608 1/10W J 100k Ω RRXA104HH013
R884 RES CHIP 1608 1/10W J 100k Ω RRXA104HH013
R885 RES CHIP 1608 1/10W J 100k Ω RRXA104HH013
R886 RES CHIP 1608 1/10W J 100k Ω RRXA104HH013
R887 RES CHIP 1608 1/10W J 22k Ω RRXA223HH013
R888 RES CHIP 1608 1/10W J 1.0k Ω RRXA102HH013
R891 RES CHIP 1608 1/10W J 20k Ω RRXA203HH013
R892 RES CHIP 1608 1/10W J 20k Ω RRXA203HH013
R893 RES CHIP 1608 1/10W J 22k Ω RRXA223HH013
R894 RES CHIP 1608 1/10W J 47k Ω RRXA473HH013
MISCELLANEOUSAC601# AC CORD W/O A GND WIRE UL/CSA 1770 NO
BLACKWAC0172LW022
B34 POW HEAT SINK A7120UH 1EM423993
B46 HEAT SINK PMM A74F0UH 1EM424517A
BC301 WIRE COPPER 6111-06003-0120 XZ40C0SHG002
BC601 BEADS INDUCTOR FBR07HA121SB-00 LLBF00STU030
BC602 BEADS INDUCTOR FBR07HA121SB-00 LLBF00STU030
BC603 BEADS INDUCTOR FBR07HA121SB-00 LLBF00STU030
BC802 BEADS INDUCTOR FBR07HA121SB-00 LLBF00STU030
BC803 BEADS INDUCTOR FBR07HA121SB-00 LLBF00STU030
BC804 BEADS INDUCTOR FBR07HA121SB-00 LLBF00STU030
BC805 BEADS INDUCTOR FBR07HA121SB-00 LLBF00STU030
BC841 BEADS INDUCTOR FBR07HA121SB-00 LLBF00STU030
CL701 WIRE ASSEMBLY 9P 9PIN/170MM WX1A94F0-002
F601# FUSE STC4A125V U/CT PAGE20CW3402
FH601 FUSE HOLDER MSF-015 LF (B110) XH01Z00LY002
FH602 FUSE HOLDER MSF-015 LF (B110) XH01Z00LY002
JK721 JACK RCA PCB S WHITE 01/RCA-101H(WH) JXRJ010YUQ02
JK722 JACK RCA PCB S RED 01/RCA-101H(RD) JXRJ010YUQ01
JK731 JACK RCA PCB S GREEN 01/RCA-101H(GN) JXRJ010YUQ03
JK732 JACK RCA PCB S BLUE 01/RCA-101H(BL) JXRJ010YUQ04
JK733 JACK RCA PCB S RED 01/RCA-101H(RD) JXRJ010YUQ01
JK741 JACK RCA PCB S WHITE 01/RCA-101H(WH) JXRJ010YUQ02
JK742 JACK SW RCA PCB S RED RCA-102H(RD) JYRJ010YUQ03
JK841 JACK RCA PCB S ORANGE 01/RCA-101H(OR) JXRJ010YUQ06
JK871 JACK RCA PCB S WHITE 01/RCA-101H(WH) JXRJ010YUQ02
JK872 JACK RCA PCB S RED 01/RCA-101H(RD) JXRJ010YUQ01
JS202 WIRE COPPER 6111-06003-0120 XZ40C0SHG002
JS302 WIRE COPPER 6111-06003-0120 XZ40C0SHG002
JS303 WIRE COPPER 6111-06003-0120 XZ40C0SHG002
JS630 WIRE COPPER 6111-06003-0120 XZ40C0SHG002
JS633 WIRE COPPER 6111-06003-0120 XZ40C0SHG002
L17 SCREW B-TIGHT D3X8 BIND HEAD+ GBJB3080
SA601# SURGE ABSORBER 470V+-10PER NVQZ10D471KB
T601# TRANS POWER BCK-28-9885 LTT2PC0XB067
TM601 EYELET TYPE D-1 0VM406868
TM602 EYELET TYPE D-1 0VM406868
TU301 TUNER UNIT ATSC TDAU4-D05A UTNATS0AL002
Ref. No. Description Part No.
Ref. No. Description Part No.
JACK CBA(MPW-B)Consists of the following:
----------
CAPACITORSC754 RES CHIP 1608 1/10W 0 Ω RRXA000HH014
C755 RES CHIP 1608 1/10W 0 Ω RRXA000HH014
C756 RES CHIP 1608 1/10W 0 Ω RRXA000HH014
C757 CHIP CERAMIC CAP.(1608) B K 2.2µF/10V CHD1AK30B225
C758 CHIP CERAMIC CAP.(1608) B K 2.2µF/10V CHD1AK30B225
RESISTORSR751 RES CHIP 1608 1/10W J 75 Ω RRXA750HH013
R752 RES CHIP 1608 1/10W J 75 Ω RRXA750HH013
R753 RES CHIP 1608 1/10W J 75 Ω RRXA750HH013
R756 RES CHIP 1608 1/10W 0 Ω RRXA000HH014
R757 RES CHIP 1608 1/10W 0 Ω RRXA000HH014
R758 RES CHIP 1608 1/10W 0 Ω RRXA000HH014
R759 RES CHIP 1608 1/10W J 15k Ω RRXA153HH013
R760 RES CHIP 1608 1/10W J 15k Ω RRXA153HH013
R761 RES CHIP 1608 1/10W J 39k Ω RRXA393HH013
R762 RES CHIP 1608 1/10W J 39k Ω RRXA393HH013
MISCELLANEOUSJK751 JACK SW DIN PCB L DIN-435C(777D) JYEL040YUQ03
JK752 JACK RCA PCB L RCA-101S(1)-03 JXRL010YUQ12
JK753 JACK RCA PCB L RCA-101S(1)-04 JXRL010YUQ13
JK754 JACK SW RCA PCB L RCA-102F(RD) JYRL010YUQ05
Ref. No. Description Part No.
INVERTER ASSEMBLYConsists of the following:
A17F6M1V-001
INVERTER CBA
-----------------------------------------------------------------FUNCTION CBAIR SENSOR CBA
A17F6M1V-001-IV
---------------------------------A17F6M1V-001-FNIR
Ref. No. Description Part No.
INVERTER CBAConsists of the following:
----------
CAPACITORSC1100 CHIP CERAMIC CAP. F Z 2.2µF/50V CHF1JZ30F225
C1101 CHIP CERAMIC CAP. F Z 2.2µF/50V CHF1JZ30F225
C1102 CHIP CERAMIC CAP. F Z 2.2µF/50V CHF1JZ30F225
C1103 CHIP CERAMIC CAP. F Z 2.2µF/50V CHF1JZ30F225
C1104 CAP CERAMIC HV 10pF/6.3KV/SL/J CCC1000MR007
C1105 CHIP CERAMIC CAP. CH J 330pF/50V CHD1JJ3CH331
C1106 CAP CERAMIC HV 10pF/6.3KV/SL/J CCC1000MR007
C1107 CHIP CERAMIC CAP. CH J 330pF/50V CHD1JJ3CH331
C1108 CAP CERAMIC HV 10pF/6.3KV/SL/J CCC1000MR007
C1109 CHIP CERAMIC CAP. CH J 330pF/50V CHD1JJ3CH331
C1110 CAP CERAMIC HV 10pF/6.3KV/SL/J CCC1000MR007
C1111 CHIP CERAMIC CAP. CH J 330pF/50V CHD1JJ3CH331
C1112 CAP CERAMIC HV 10pF/6.3KV/SL/J CCC1000MR007
C1113 CHIP CERAMIC CAP. CH J 330pF/50V CHD1JJ3CH331
C1114 CAP CERAMIC HV 10pF/6.3KV/SL/J CCC1000MR007
C1115 CHIP CERAMIC CAP. CH J 330pF/50V CHD1JJ3CH331
C1116 CHIP CERAMIC CAP. F Z 2.2µF/50V CHF1JZ30F225
C1117 CHIP CERAMIC CAP. F Z 2.2µF/50V CHF1JZ30F225
C1118 CHIP CERAMIC CAP. CH J 330pF/50V CHD1JJ3CH331
C1119 CHIP CERAMIC CAP. CH J 330pF/50V CHD1JJ3CH331
C1120 CHIP CERAMIC CAP. CH J 330pF/50V CHD1JJ3CH331
2011/10/31 14-7 A17F6EL.fm
C1121 CHIP CERAMIC CAP. CH J 330pF/50V CHD1JJ3CH331
C1122 CHIP CERAMIC CAP. CH J 330pF/50V CHD1JJ3CH331
C1123 CHIP CERAMIC CAP. CH J 330pF/50V CHD1JJ3CH331
C1201 CHIP CERAMIC CAP.(1608) B K 0.1µF/50V CHD1JK30B104
C1202 CHIP CERAMIC CAP.(1608) B K 6800pF/50V CHD1JK30B682
C1203 CHIP CERAMIC CAP.(1608) B K 6800pF/50V CHD1JK30B682
C1204 CHIP CERAMIC CAP.(1608) B K 0.1µF/50V CHD1JK30B104
C1205 CHIP CERAMIC CAP. F Z 2.2µF/50V CHF1JZ30F225
C1206 ELECTROLYTIC CAP. 10µF/50V M CE1JMASDL100
C1207 CHIP CERAMIC CAP.(1608) B K 1000pF/50V CHD1JK30B102
C1208 CAP CHIP 3216 B K 0.47µF/50V CA1J474TE142
C1209 CAP CHIP 3216 B K 0.47µF/50V CA1J474TE142
C1210 CHIP CERAMIC CAP.(1608) B K 0.47µF/16V CHD1CK30B474
C1212 CHIP CERAMIC CAP.(1608) B K 0.47µF/16V CHD1CK30B474
C1213 CHIP CERAMIC CAP.(1608) B K 0.01µF/50V CHD1JK30B103
C1300 CHIP CERAMIC CAP.(1608) B K 0.1µF/50V CHD1JK30B104
C1301 CHIP CERAMIC CAP.(1608) B K 1000pF/50V CHD1JK30B102
C1302 ELECTROLYTIC CAP. 10µF/50V M CE1JMASDL100
C1303 CHIP CERAMIC CAP.(1608) B K 0.1µF/50V CHD1JK30B104
C1304 ELECTROLYTIC CAP. 220µF/35V M CE1GMASDL221
C1305 CHIP CERAMIC CAP.(1608) B K 0.1µF/50V CHD1JK30B104
C1311 CHIP CERAMIC CAP.(1608) B K 1000pF/50V CHD1JK30B102
C1500 CHIP CERAMIC CAP.(1608) B K 0.01µF/50V CHD1JK30B103
C1501 CHIP CERAMIC CAP.(1608) B K 1000pF/50V CHD1JK30B102
C1700 ELECTROLYTIC CAP. 2200µF/35V M CE1GMZNDL222
C1701 ELECTROLYTIC CAP. 2200µF/35V M CE1GMZNDL222
C1702 CAP CHIP 3216 B K 1µF/50V CA1J105TE142
C1703 CHIP CERAMIC CAP.(1608) B K 1000pF/50V CHD1JK30B102
C1704 CHIP CERAMIC CAP.(1608) B K 1000pF/50V CHD1JK30B102
C1705 CHIP CERAMIC CAP.(1608) B K 0.022µF/50V CHD1JK30B223
C1706 CHIP CERAMIC CAP.(1608) B K 1000pF/50V CHD1JK30B102
C1707 CHIP CERAMIC CAP.(1608) B K 1000pF/50V CHD1JK30B102
C1708 CHIP CERAMIC CAP.(1608) B K 0.022µF/50V CHD1JK30B223
C1905# SAFTY CAP. 1000pF/250V KX CA2E102MR101
C1910 CAP ELECTROLYTIC 270µF/200V CEA271DYG005
C1930 CERAMIC CAP. 680pF/2KV CA3D681PAN04
C1931# CHIP CERAMIC CAP. B K 1800pF/50V CHD1JK30B182
C1932 CHIP CERAMIC CAP. B K 0.056µF/50V CHD1JK30B563
C1933 CHIP CERAMIC CAP. B K 0.1µF/50V CHE1JK30B104
C1970 CHIP CERAMIC CAP. B K 2200pF/50V CHD1JK30B222
C1981 CHIP CERAMIC CAP. F Z 0.01µF/50V CHD1JZ30F103
C1982 ELECTROLYTIC CAP. 0.47µF/50V M CE1JMASDLR47
C1990 CERAMIC CAP. 1500pF/2KV CA3D152PAN04
C1993 ELECTROLYTIC CAP. 2200µF/35V M CE1GMZNDL222
C1994 ELECTROLYTIC CAP. 2200µF/35V M CE1GMZNDL222
CONNECTORSCN1001 FFC CONNECTOR 15P IMSA-9615S-15A-PP-A JC96J15ER007
CN1003 FFC CONNECTOR IMSA-9615S-11A-PP-A JC96J11ER007
CN1100# CONNECTOR/JACK 1747386-1 JB17J02AP002
CN1101# CONNECTOR/JACK 1747386-1 JB17J02AP002
CN1102# CONNECTOR/JACK 1747386-1 JB17J02AP002
CN1901# CONNECTOR PRINT OSU 3 S B3P4-VH-L J3VH030JG015
DIODESD1200 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133
D1201 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133
D1202 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133
D1203 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133
D1300 DIODE ZENER 5V6BSB-T26 NDTB5R6BST26
D1301 DIODE ZENER 5V6BSB-T26 NDTB5R6BST26
D1500 SWITCHING DIODE DAN202U T106 QD1Z0DAN202U
D1501 SWITCHING DIODE DAN202U T106 QD1Z0DAN202U
D1502 SWITCHING DIODE DAN202U T106 QD1Z0DAN202U
Ref. No. Description Part No.
D1503 SWITCHING DIODE DAN202U T106 QD1Z0DAN202U
D1504 SWITCHING DIODE DAN202U T106 QD1Z0DAN202U
D1505 SWITCHING DIODE DAN202U T106 QD1Z0DAN202U
D1506 SWITCHING DIODE DAN202U T106 QD1Z0DAN202U
D1507 SWITCHING DIODE DAN202U T106 QD1Z0DAN202U
D1508 SWITCHING DIODE DAN202U T106 QD1Z0DAN202U
D1700 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133
D1701 DIODE ZENER 15BSB-T26 NDTB015BST26
D1702 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133
D1703 DIODE ZENER 15BSB-T26 NDTB015BST26
D1704 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133
D1705 DIODE ZENER 15BSB-T26 NDTB015BST26
D1706 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133
D1707 DIODE ZENER 15BSB-T26 NDTB015BST26
D1930# DIODE ZENER 27BSB-T26 NDTB027BST26
D1931 DIODE ZENER 5V6BSB-T26 NDTB5R6BST26
D1932 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133
D1933 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133
D1934# DIODE ZENER 1ZB36BB NDWZ0001ZB36
D1970 DIODE ZENER 5V6BSB-T26 NDTB5R6BST26
D1971 DIODE ZENER 30BSB-T26 NDTB030BST26
D1973 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133
D1990 DIODE SCHOTTKY SB3150BH NDWZ00SB3150
D1991 DIODE SCHOTTKY SB3150BH NDWZ00SB3150
D1992 DIODE SCHOTTKY SB3150BH NDWZ00SB3150
D1994 DIODE ZENER 1ZB30BB NDWZ0001ZB30
ICSIC1200 IC INVERTER CONTROL BD9244AFV/SSOP/
24PINQSCA0T0RM222
IC1930# IC PHOTOCOUPLER TLP781F(D4-FUNBLL F) QPEL781FBLLF
IC1931# IC PHOTOCOUPLER TLP781F(D4-FUNBLL F) QPEL781FBLLF
TRANSISTORSQ1201 CHIP TRANSISTOR KTC3875S-Y-RTK/P NQ1YKTC3875S
Q1202 CHIP TRANSISTOR KTC3875S-Y-RTK/P NQ1YKTC3875S
Q1300 PNP TRANSISTOR SMD 2SA1576UBTLQ QQ1Q2SA1576U
Q1301 CHIP TRANSISTOR KTC3875S-Y-RTK/P NQ1YKTC3875S
Q1303 PNP TRANSISTOR SMD 2SA1576UBTLQ QQ1Q2SA1576U
Q1700# FET MOS SMD TK50P04M1(T6RSS-Q) QF1ZK50P04M1
Q1701# FET MOS SMD TK50P04M1(T6RSS-Q) QF1ZK50P04M1
Q1702# FET MOS SMD TK50P04M1(T6RSS-Q) QF1ZK50P04M1
Q1703# FET MOS SMD TK50P04M1(T6RSS-Q) QF1ZK50P04M1
Q1930# MOS FET TK7A50D(FUNAI QEWZTK7A50DQ
Q1931# TRANSISTOR KTC3198-Y-AT/P NQSYKTC3198P
Q1932# TRANSISTOR 2SC2120-O(TE2 F T) QQS02SC2120F
Q1970 CHIP TRANSISTOR KTC3875S-Y-RTK/P NQ1YKTC3875S
Q1971 CHIP TRANSISTOR KTC3875S-Y-RTK/P NQ1YKTC3875S
Q1972 CHIP TRANSISTOR KTC3875S-Y-RTK/P NQ1YKTC3875S
RESISTORSR1100 RES CHIP 1608 1/10W F 39.0k Ω RTW3902HH008
R1101 RES CHIP 1608 1/10W 0 Ω RRXA000HH014
R1102 RES CHIP 1608 1/10W F 2.20k Ω RTW2201HH008
R1103 RES CARBON FILM T 1/4W G 470 Ω RCX4471T1002
R1104 RES CHIP 1608 1/10W F 100 Ω RTW1000HH008
R1105 RES CHIP 1608 1/10W F 13.0 Ω RTW13R0HH008
R1106 RES CARBON FILM T 1/4W G 470 Ω RCX4471T1002
R1107 RES CHIP 1608 1/10W F 100 Ω RTW1000HH008
R1108 RES CHIP 1608 1/10W F 13.0 Ω RTW13R0HH008
R1109 RES CHIP 1608 1/10W F 39.0k Ω RTW3902HH008
R1110 RES CHIP 1608 1/10W 0 Ω RRXA000HH014
R1111 RES CHIP 1608 1/10W F 2.20k Ω RTW2201HH008
R1112 RES CHIP 1608 1/10W F 39.0k Ω RTW3902HH008
R1113 RES CHIP 1608 1/10W 0 Ω RRXA000HH014
R1114 RES CHIP 1608 1/10W F 2.20k Ω RTW2201HH008
Ref. No. Description Part No.
2011/10/31 14-8 A17F6EL.fm
R1115 RES CARBON FILM T 1/4W G 470 Ω RCX4471T1002
R1116 RES CHIP 1608 1/10W F 100 Ω RTW1000HH008
R1117 RES CHIP 1608 1/10W F 13.0 Ω RTW13R0HH008
R1118 RES CARBON FILM T 1/4W G 470 Ω RCX4471T1002
R1119 RES CHIP 1608 1/10W F 100 Ω RTW1000HH008
R1120 RES CHIP 1608 1/10W F 13.0 Ω RTW13R0HH008
R1121 RES CHIP 1608 1/10W F 39.0k Ω RTW3902HH008
R1122 RES CHIP 1608 1/10W 0 Ω RRXA000HH014
R1123 RES CHIP 1608 1/10W F 2.20k Ω RTW2201HH008
R1124 RES CHIP 1608 1/10W F 39.0k Ω RTW3902HH008
R1125 RES CHIP 1608 1/10W 0 Ω RRXA000HH014
R1126 RES CHIP 1608 1/10W F 2.20k Ω RTW2201HH008
R1127 RES CARBON FILM T 1/4W G 470 Ω RCX4471T1002
R1128 RES CHIP 1608 1/10W F 100 Ω RTW1000HH008
R1129 RES CHIP 1608 1/10W F 13.0 Ω RTW13R0HH008
R1130 RES CARBON FILM T 1/4W G 470 Ω RCX4471T1002
R1131 RES CHIP 1608 1/10W F 100 Ω RTW1000HH008
R1132 RES CHIP 1608 1/10W F 13.0 Ω RTW13R0HH008
R1133 RES CHIP 1608 1/10W F 39.0k Ω RTW3902HH008
R1134 RES CHIP 1608 1/10W 0 Ω RRXA000HH014
R1135 RES CHIP 1608 1/10W F 2.20k Ω RTW2201HH008
R1200 RES CHIP 1608 1/10W J 68k Ω RRXA683HH013
R1201 RES CHIP 1608 1/10W J 68k Ω RRXA683HH013
R1202 RES CHIP 1608 1/10W F 130k Ω RTW1303HH008
R1203 RES CHIP 1608 1/10W F 8.20k Ω RTW8201HH008
R1204 RES CHIP 1608 1/10W F 75.0k Ω RTW7502HH008
R1205 RES CHIP 1608 1/10W F 560k Ω RTW5603HH008
R1206 RES CHIP 1608 1/10W J 10k Ω RRXA103HH013
R1207 RES CHIP 1608 1/10W J 33k Ω RRXA333HH013
R1208 RES CHIP 1608 1/10W J 22k Ω RRXA223HH013
R1209 RES CHIP 1608 1/10W J 4.7k Ω RRXA472HH013
R1212 RES CHIP 1608 1/10W J 10k Ω RRXA103HH013
R1213 RES CHIP 1608 1/10W J 4.7k Ω RRXA472HH013
R1214 RES CHIP 1608 1/10W 0 Ω RRXA000HH014
R1215 RES CHIP 1608 1/10W J 10k Ω RRXA103HH013
R1216 RES CHIP 1608 1/10W J 100 Ω RRXA101HH013
R1221 RES CHIP 1608 1/10W J 1.0 Ω RRXA1R0HH013
R1222 RES CHIP 1608 1/10W J 10 Ω RRXA100HH013
R1223 RES CHIP 1608 1/10W J 10 Ω RRXA100HH013
R1229 RES CHIP 1608 1/10W 0 Ω RRXA000HH014
R1300 RES CHIP 1608 1/10W F 10.0k Ω RTW1002HH008
R1301 RES CHIP 1608 1/10W F 47.0k Ω RTW4702HH008
R1302 RES CHIP 1608 1/10W F 51.0k Ω RTW5102HH008
R1303 RES CHIP 1608 1/10W J 4.7k Ω RRXA472HH013
R1304 RES CHIP 1608 1/10W J 4.7k Ω RRXA472HH013
R1305 METAL OXIDE RES. 2W J 510 Ω RN02511ZU001
R1306 RES CHIP 1608 1/10W J 10k Ω RRXA103HH013
R1307 RES CHIP 1608 1/10W J 1.0k Ω RRXA102HH013
R1308 RES CHIP 1608 1/10W J 4.7k Ω RRXA472HH013
R1309 RES CHIP 1608 1/10W J 10k Ω RRXA103HH013
R1310 RES CHIP 1608 1/10W J 22k Ω RRXA223HH013
R1500 RES CHIP 1608 1/10W F 1.00M Ω RTW1004HH008
R1501 RES CHIP 1608 1/10W F 100k Ω RTW1003HH008
R1502 RES CHIP 1608 1/10W F 100k Ω RTW1003HH008
R1503 RES CHIP 1608 1/10W F 100k Ω RTW1003HH008
R1504 RES CHIP 1608 1/10W F 100k Ω RTW1003HH008
R1505 RES CHIP 1608 1/10W F 100k Ω RTW1003HH008
R1506 RES CHIP 1608 1/10W F 100k Ω RTW1003HH008
R1507 RES CHIP 1608 1/10W F 100k Ω RTW1003HH008
R1508 RES CHIP 1608 1/10W F 100k Ω RTW1003HH008
R1509 RES CHIP 1608 1/10W F 100k Ω RTW1003HH008
R1510 RES CHIP 1608 1/10W F 100k Ω RTW1003HH008
R1511 RES CHIP 1608 1/10W F 100k Ω RTW1003HH008
Ref. No. Description Part No.
R1512 RES CHIP 1608 1/10W F 100k Ω RTW1003HH008
R1513 RES CHIP 1608 1/10W F 1.00M Ω RTW1004HH008
R1514 RES CHIP 1608 1/10W F 39.0k Ω RTW3902HH008
R1515 RES CHIP 1608 1/10W F 27.0k Ω RTW2702HH008
R1516 RES CHIP 1608 1/10W 0 Ω RRXA000HH014
R1700 RES CHIP 1608 1/10W J 100 Ω RRXA101HH013
R1701 RES CHIP 1608 1/10W J 10k Ω RRXA103HH013
R1702 RES CHIP 1608 1/10W J 100 Ω RRXA101HH013
R1703 RES CHIP 1608 1/10W J 10k Ω RRXA103HH013
R1704 METAL OXIDE FILM RES. 1W J 4.7 Ω RN014R7ZU001
R1705 RES CHIP 1608 1/10W J 100 Ω RRXA101HH013
R1706 RES CHIP 1608 1/10W J 10k Ω RRXA103HH013
R1707 RES CHIP 1608 1/10W J 100 Ω RRXA101HH013
R1708 RES CHIP 1608 1/10W J 10k Ω RRXA103HH013
R1709 METAL OXIDE FILM RES. 1W J 4.7 Ω RN014R7ZU001
R1930 RES CARBON FILM T 1/4W J 47 Ω RCX4470T1001
R1931 RES CARBON FILM T 1/4W J 47k Ω RCX4473T1001
R1932 RES CARBON FILM T 1/4W J 120 Ω RCX4121T1001
R1933 RES CARBON FILM T 1/4W J 120 Ω RCX4121T1001
R1934 RES CARBON FILM T 1/4W J 120 Ω RCX4121T1001
R1935 RES CARBON FILM T 1/4W J 1.5k Ω RCX4152T1001
R1936 RES CARBON FILM T 1/4W J 180 Ω RCX4181T1001
R1937# METAL OXIDE FILM RES. 2W J 0.39 Ω RN02R39ZU001
R1938 RES CARBON FILM T 1/4W J 82k Ω RCX4823T1001
R1939 RES CARBON FILM T 1/4W J 2.2k Ω RCX4222T1001
R1949 RES CARBON FILM T 1/4W J 150k Ω RCX4154T1001
R1967 RES CARBON FILM T 1/4W J 3.9k Ω RCX4392T1001
R1970 RES CARBON FILM T 1/4W J 220 Ω RCX4221T1001
R1972 RES CHIP 1608 1/10W J 22k Ω RRXA223HH013
R1973 RES CHIP 1608 1/10W J 3.3k Ω RRXA332HH013
R1977 RES CHIP 1608 1/10W F 20.0k Ω RTW2002HH008
R1979 RES CHIP 1608 1/10W F 6.80k Ω RTW6801HH008
R1980 RES CHIP 1608 1/10W F 180 Ω RTW1800HH008
R1981 RES CHIP 1608 1/10W 0 Ω RRXA000HH014
R1982 RES CHIP 1608 1/10W J 1.5k Ω RRXA152HH013
R1986 RES CHIP 1608 1/10W J 1.0k Ω RRXA102HH013
R1988 RES CHIP 1608 1/10W J 1.0k Ω RRXA102HH013
MISCELLANEOUSB34 POW HEAT SINK A7120UH 1EM423993
BC1301 WIRE COPPER 6111-06003-0120 XZ40C0SHG002
BC1930 BEADS INDUCTOR FBR07HA121SB-00 LLBF00STU030
BC1931 BEADS INDUCTOR FBR07HA121SB-00 LLBF00STU030
JS1200 WIRE COPPER 6111-06003-0120 XZ40C0SHG002
L17 SCREW B-TIGHT D3X8 BIND HEAD+ GBJB3080
T1950# TRANS POWER BCK-28CM LTT2PCMEK031
When you replace one of the below Trans Inverters on this CBA, please replace with the one that has same parts number.Do not mix different parts number’s Trans Inverter.
T1100# TRANS INV TZ.7617A.101 LTZ3PZDAR014
T1101# TRANS INV TZ.7617A.101 LTZ3PZDAR014
T1102# TRANS INV TZ.7617A.101 LTZ3PZDAR014
or
T1100# TRANS INV HVT-325 LTZ3PZ0XB018
T1101# TRANS INV HVT-325 LTZ3PZ0XB018
T1102# TRANS INV HVT-325 LTZ3PZ0XB018
Ref. No. Description Part No.
2011/10/31 14-9 A17F6EL.fm
FUNCTION CBA
IR SENSOR CBA
Ref. No. Description Part No.
FUNCTION CBAConsists of the following:
----------
CAPACITORC108 CAP CERAMIC (AX) 0.1µF/50V/F/Z CA1J104TU062
RESISTORSR108 RES CARBON FILM T 1/4W J 220 Ω RCX4221T1001
R109 RES CARBON FILM T 1/4W G 10k Ω RCX4103T1002
R111 RES CARBON FILM T 1/4W G 4.7k Ω RCX4472T1002
R112 RES CARBON FILM T 1/4W G 2.7k Ω RCX4272T1002
R113 RES CARBON FILM T 1/4W G 4.7k Ω RCX4472T1002
R114 RES CARBON FILM T 1/4W G 8.2k Ω RCX4822T1002
R115 RES CARBON FILM T 1/4W G 18k Ω RCX4183T1002
SWITCHESSW101B TACT SWITCH SKQSAB SST0101AL038
SW103B TACT SWITCH SKQSAB SST0101AL038
SW104B TACT SWITCH SKQSAB SST0101AL038
SW105B TACT SWITCH SKQSAB SST0101AL038
SW106B TACT SWITCH SKQSAB SST0101AL038
SW107B TACT SWITCH SKQSAB SST0101AL038
Ref. No. Description Part No.
IR SENSOR CBAConsists of the following:
----------
CAPACITORSC101 ELECTROLYTIC CAP. 47µF/16V M H7 CE1CMAVSL470
C103 CHIP CERAMIC CAP. CH J 330pF/50V CHD1JJ3CH331
C104 CHIP CERAMIC CAP.(1608) F Z 0.1µF/50V CHD1JZ30F104
DIODED101 LED (WHITE) SLR343WBC7T3XM QPWM343WBC7T
RESISTORSR101 RES CARBON FILM T 1/4W J 100 Ω RCX4101T1001
R102 RES CHIP 1608 1/10W J 3.3k Ω RRXA332HH013
R103 RES CHIP 1608 1/10W J 9.1k Ω RRXA912HH013
R106 RES CHIP 1608 1/10W J 1.0k Ω RRXA102HH013
MISCELLANEOUSCL102 WIRE ASSEMBLY 5PIN 5PIN/180MM WX1A17F6-201
CL103 WIRE ASSEMBLY 4PIN 4PIN/35MM WX1A17F6-202
RS101 SENSOR REMOTE RECEIVER KSM-712TH2E USESJRSKK044
2011/10/31 14-10 A17FCCA.fm
TYPE A
PARTS LIST [32PFL3506/F7 (Serial No.: XA1)]
Mechanical Parts
PRODUCT SAFETY NOTE: Products marked with a # have special characteristics important to safety. Before replacing any of these components, read carefully the product safety notice in this service manual. Don't degrade the safety of the product through improper servicing.
NOTE: Parts that are not assigned part numbers (---------) are not available.
Different parts from the original model 32PFL3506/F7 (Serial No. : DS1)
Ref. No. Description Part No.
A12# RATING LABEL A17FCMA ----------
S1 CARTON A17FCMA 1EM436099
S17 CARTON LABEL A17FCMA ----------
X2# OWNERS MANUAL A17FCMA 1EMN28539
2011/11/22 14-11 A17FCEL.fm
Electrical Parts
PRODUCT SAFETY NOTE: Products marked with a # have special characteristics important to safety. Before replacing any of these components, read carefully the product safety notice in this service manual. Don't degrade the safety of the product through improper servicing.
NOTES:
1. Parts that are not assigned part numbers (---------) are not available.
2. Tolerance of Capacitors and Resistors are noted with the following symbols.
Different parts from the original model 32PFL3506/F7 (Serial No. : DS1)
There are no different parts from the original model 32PFL3506/F7 (Serial No : DS1).Refer to the parts list for the original model 32PFL3506/F7 (Serial No : DS1).
C.....±0.25% D.....±0.5% F.....±1%
G.....±2% J......±5% K.....±10%
M.....±20% N.....±30% Z.....+80/-20%
2011/10/31 14-12 A17FGCA.fm
TYPE B
PARTS LIST[32PFL3506/F7 (Serial No.: DS2), 32PFL3000/F8 (Serial No.: XA2)]
Mechanical Parts
PRODUCT SAFETY NOTE: Products marked with a # have special characteristics important to safety. Before replacing any of these components, read carefully the product safety notice in this service manual. Don't degrade the safety of the product through improper servicing.
NOTE: Parts that are not assigned part numbers (---------) are not available.
Different parts from the original model 32PFL3506/F7 (Serial No. : DS1)
Ref. No. Description Part No.
A8 JACK HOLDER A17FGUH 1EM226563
A15 Not used
A42 ENERGY GUIDE LABEL A17F6UH ----------
B1 SHIELD BOX A17F4UH 1EM225624
S1 CARTON A17FGUH 1EM436857
X2# OWNERS MANUAL A17FGUH 1EMN28819
X6 QUICK START GUIDE A17FGUH 1EMN28820
2011/10/31 14-13 A17FGEL.fm
Electrical Parts
PRODUCT SAFETY NOTE: Products marked with a # have special characteristics important to safety. Before replacing any of these components, read carefully the product safety notice in this service manual. Don't degrade the safety of the product through improper servicing.
NOTES:
1. Parts that are not assigned part numbers (---------) are not available.
2. Tolerance of Capacitors and Resistors are noted with the following symbols.
Different parts from the original model 32PFL3506/F7 (Serial No. : DS1)
C.....±0.25% D.....±0.5% F.....±1%
G.....±2% J......±5% K.....±10%
M.....±20% N.....±30% Z.....+80/-20%
Ref. No. Description Part No.
DIGITAL MAIN CBA UNIT A17FGMMA-001
MPW CBA A17FGMPW-001
POWER SUPPLY CBA(MPW-A) ----------
C403 ELECTROLYTIC CAP. 10µF/50V M CE1JMASDL100
C606 Not used
C606A CHIP CERAMIC CAP. B K 1500pF/50V CHD1JK30B152
C608 Not used
C608A CHIP CERAMIC CAP.(1608) B K 1000pF/50V CHD1JK30B102
C646 Not used
C646A CHIP CERAMIC CAP. B K 2200pF/50V CHD1JK30B222
C650 Not used
C650A CHIP CERAMIC CAP.(1608) B K 0.022µF/50V CHD1JK30B223
C658 ELECTROLYTIC CAP. 100µF/10V M CE1AMASDL101
C734 Not used
C735 Not used
C736 Not used
C801 ELECTROLYTIC CAP. 1µF/50V M H7 CE1JMAVSL1R0
C815 ELECTROLYTIC CAP. 1µF/50V M H7 CE1JMAVSL1R0
C835 CHIP CERAMIC CAP. CH J 220pF/50V CHD1JJ3CH221
C837 CHIP CERAMIC CAP. CH J 220pF/50V CHD1JJ3CH221
C875 CHIP CERAMIC CAP.(1608) CH J 47pF/50V CHD1JJ3CH470
C876 CHIP CERAMIC CAP.(1608) CH J 47pF/50V CHD1JJ3CH470
C877 CHIP CERAMIC CAP.(1608) B K 1000pF/50V CHD1JK30B102
C878 CHIP CERAMIC CAP.(1608) B K 1000pF/50V CHD1JK30B102
C882 RES CHIP 1608 1/10W J 1.0k Ω RRXA102HH013
C883 RES CHIP 1608 1/10W J 1.0k Ω RRXA102HH013
D423 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133
D607A RES CHIP 1608 1/10W 0 Ω RRXA000HH014
D621 Not used
D652A RES CHIP 1608 1/10W 0 Ω RRXA000HH014
D659A RES CHIP 1608 1/10W 0 Ω RRXA000HH014
IC871 IC OP AMP NJM4558M(TE2)-PBF/DM QSCA0T0JR010
R209 Not used
R211 Not used
R214 Not used
R302 Not used
R303 Not used
R409 RES CHIP 1608 1/10W J 100 Ω RRXA101HH013
R691 Not used
R693 Not used
R698 Not used
R701 METAL OXIDE FILM RES. 2W J 2.2 Ω RN022R2ZU001
R702 METAL OXIDE FILM RES. 1W J 2.2 Ω RN012R2ZU001
R801 Not used
R810 Not used
R811 Not used
R812 Not used
R813 RES CHIP 1608 1/10W J 22k Ω RRXA223HH013
R815 RES CHIP 1608 1/10W J 22k Ω RRXA223HH013
R842 Not used
R875 Not used
R876 Not used
R879 RES CHIP 1608 1/10W J 16k Ω RRXA163HH013
R880 RES CHIP 1608 1/10W J 16k Ω RRXA163HH013
R891 RES CHIP 1608 1/10W J 33k Ω RRXA333HH013
R892 RES CHIP 1608 1/10W J 33k Ω RRXA333HH013
R896 RES CHIP 1608 1/10W 0 Ω RRXA000HH014
JACK CBA(MPW-B) ----------
C754 Not used
C755 Not used
C756 Not used
Ref. No. Description Part No.
15-1 PL11.0REV
REVISION HISTORY
Chassis PL11.0• 2011-03-28 32PFL3506/F7 (Serial No. : DS1) added
• 2011-08-25 32PFL3506/F7 (Serial No. : DS2) added
• 2011-11-05 32PFL3000/F8 (Serial No. : XA1) addedNote: Identical product to the 32PFL3506/F7 (Serial No.: DS1).
• 2011-11-05 32PFL3000/F8 (Serial No. : XA2) addedNote: Identical product to the 32PFL3506/F7 (Serial No.: DS2).
• 2011-11-28 32PFL3506/F7 (Serial No. : XA1) added
• TBD 32PFL3506/F7 (Serial No. : DS3) added
PL11.0COM
COMPARISON LIST OF MODEL NAME
Chassis PL11.032PFL3506/F7 (DS1) A17F6UH
(DS2) A17FGUH
(DS3) A17FHUH
(XA1) A17FCMA
32PFL3000/F8 (XA1) A1AF7MA
(XA2) A1AFBMA