LW 35018 5
LW 35018 WWW.LEADWARRIOR.COM [email protected] COPYRIGHT 2004
LEADWARRIORHISTORICAL MINIATURE Ebay: LEADWARRIOR
WWW.LEADWARRIOR.COM
LW 35018
The Sd.Kfz.251/17 was the Anti-Aircraft Gun modification of widely used Sd.Kfz.251 halftrack.Photographic evidence shows different models using the Sd.Kfz.251 Ausf C chassis. Most photographed (although only 10 pieces and two command vehicles were constructed) is the "Luftwaffe-Fla ausführung" (air force anti-aircraft version). It involved considerable rebuilding of the superstructure: the sides have been extended to give the gun a 360 degrees rotation freedom. The sides also can be lowered to create a platform. The Machine Guns were dismounted, it is believed that they were transported inside the vehicle. The box with spare gun barrels was installed in place of front Machine Gun.The command vehicle got the same collapsible sides. The command-vehicles were similar to the AA vehicle but without the gun. Unlike the FlaK machines, the front machine gun (MG-34 or MG-42) remained in place.
These command vehicles were equipped with additional radio FU-10, consisted of 30-W.S. transmitter with a frame-antenna, and Torn.E. b receiver. One command vehicle leads 4 flak vehicles
63 RESIN PARTS
Sd.Kfz. 251/17
BASIC DATA
Length
Ñlearance
Amour
Engine
Transmission
Armament
Radio
Crew
5.8 m
30 cm
8 - 14.5 mm
Maybach HL 42 TUKRM
Schub, 4 forw., 1 rev.
2 x 7.92 MG
FuG Spr Ger f, Fu-10
4 - 6
( Luftwaffe FlaK COMMAND Vehicle )
for DRAGON (6187) Sd.Kfz.251/1 Ausf. C
1:35 CONVERSION KIT2 METAL PARTS
20
20
17* Same for the other side.
2828
28
28* Metal part
7
LW 35018 WWW.LEADWARRIOR.COM [email protected] COPYRIGHT 2004
* PAINT: Panzer Yellow overall
* Metal part
?
1110
2MAKE 12
19
19
1919
5 (4)
15 (16)
16 (15)
14 (13)
13 (14)
5
* Numbers of the parts to be used on the right side, if not the same, are in parentheses: ( )
* Refer to the pins of the parts 6 when positioning parts 19.
LW 35018 1
LW 35018 WWW.LEADWARRIOR.COM [email protected] COPYRIGHT 2004
STUDY THE INSTRUCTION CAREFULLY BEFORE ASSEMBLING.
TEST FIT PARTS TOGETHER BEFORE CEMENTING.
USE CYANOACRYLATE GLUE FOR METAL AND RESIN PARTS.
2MAKE
?
Cut / Remove part
Optional
Repeat several times
Repeat on mirror side
Heat and stretch sprue to make plastic wire
Bend part
11
2
3
4
5
6
7
89
10 11 12
13
14
15
16
17
18
19
20
X4
X2
LW 35018 4
21
22
24
25 26
27
28
69
7
8 6
9
7
8
96
6
Fix parts 6 opened or closed
?
6
LW 35018 WWW.LEADWARRIOR.COM [email protected] COPYRIGHT 2004
LW 35018 2
LW 35018 WWW.LEADWARRIOR.COM [email protected] COPYRIGHT 2004
1
DAGON kit Part A1
20 mm
20 mm
DAGON kit Part B1
DAGON kit Part B2
9,6 mm
2 1. Follow the DRAGON kit manual, steps 1 - 7. DO NOT use parts B19, B24.
2. Execute step 8 of DRAGON manual: DO NOT use parts A5, A6, A7, A13,D2, D3, D8, D12, B27.
3. Execute step 9 of DRAGON manual: DO NOT use part C44.
4. Execute step 10 of DRAGON manual: DO NOT use parts D7, D9, D13, D15, D16.
5. Execute step 11 of DRAGON manual: DO NOT use parts B25, B26, B28, D23, D31.
6. Follow the DRAGON kit manual, step 12.
7. Execute step 13 of DRAGON manual: DO NOT use parts D24.
8. Execute step 14 of DRAGON manual: DO NOT use part B31.
21
21
24
25
26
27
LW 35018 3
LW 35018 WWW.LEADWARRIOR.COM [email protected] COPYRIGHT 2004
3
4
1
2
3
3
3
3
18
18
18
18
22
21
21
24
25
26
27
LW 35018 3
LW 35018 WWW.LEADWARRIOR.COM [email protected] COPYRIGHT 2004
3
4
1
2
3
3
3
3
18
18
18
18
22