FULLFULLFULL CONCEALED CONCEALED CONCEALED
CLEATSCLEATSCLEATS
FAIRLEADSFAIRLEADSFAIRLEADS
GAS SPRINGSGAS SPRINGSGAS SPRINGS CLEATSCLEATSCLEATS
CLEATS &CLEATS &CLEATS & FAIRLEADSFAIRLEADSFAIRLEADS
A
EF
DC
B1
3
4
G
2
A new awesome feature onboard. Just use your foot to open the cleat. The gas springs will pop up the cleat for you. And to close it? Just use again your foot: the cleat keeps closed position automatically. Do you need aesthetics, functionality, and strength? This cleat has all of them. Available in stainless steel, aluminum and titanium.
Solimar can change some dimensions if it is necessary
CODE A C D E F G Rope Screw Load (Kg) N L I H
ALUMINIUM
092N200L 200 35 18 50 68 130 18 3xM8 1400 60 30 140 70
092N250L 250 47 20 55 75 150 22 3xM8 2300 72 35 174 85
092N300L 300 65 23 60 83 210 28 3xM12 4250 83 38 204 100
092N350L 350 70 25 65 80 210 30 3xM12 5300 93 40 224 105
092N400L 400 80 27 75 102 210 32 3xM14 6400 105 49 260 110
STAINLESS STEEL
092N200 200 35 18 50 68 130 18 3xM8 2300 60 30 140 70
092N250 250 47 20 55 75 150 22 3xM8 4250 72 35 174 85
092N300 300 65 23 60 83 210 28 3xM12 5300 83 38 204 100
092N350 350 70 25 65 80 210 30 3xM12 9300 93 40 224 105
092N400 400 80 27 75 102 210 32 3xM14 13000 105 49 260 110
ALUMINIUM VERSION
Material Finishing
1 AL 6082 Titanium/Black anodization
2 ERGAL 55 Titanium/Black anodization
3 AL 6082 Titanium/Black anodization
4 AL 6082 Titanium/Black anodization
STAINLESS STEEL VERSION
Material Finishing
1 AISI 316 Mirror polished
2 AISI 316 / NITRONIC 50 Mirror polished
3 AISI 316 Mirror polished
4 AISI 316 Mirror polished
The old version is still available
TECHNICAL ASSEMBLING INSTRUCTIONS FOR CLEATS
List of the components: 1 Horizontal beam of the cleat (securing mooring ropes) 2 Cleat frame 3 Slot for the spanner to assembly/disassembly of the
rod 3a Slot for the spanner to assembly/disassembly of the
gas spring cylinder 4 Cleat rod 5 Gas spring cylinder 6 Under deck counter plate (on request) 7 Locking bolts
Before fitting the cleat on the deck, you have to check,(when the cleat is opened in working position), if it is possible to put the locking bolts through the holes. Only if this step is not possible, you have to unscrew the rods (4), to rotate the beam of the cleats and to fit the bolts through the locking holes (the rods could have a slot for wrench. If not, they have an hexagon you can reach only from below after removing the part 5 and using a long allen key) . Warning : the frame (2) must match perfectly the deck . After the assembly of the frame (2) fit the bolts and tighten securely the nuts below the counter plate under the deck. We suggest you to protect the bolts with anti-corrosion grease.
The flush cleat combines aesthetics and functionality.
The frame of the cleats is very slim. The ergonomic shape of the beam (1) allows to open/close easily the cleat with a slight pressure of the hand or of the foot. The cleats are available made of AL6082, A304-316 stainless steel and the finishing can be: mirror polished, peening, silver anodizing, black or grey hardkote anodizing.
Assembling instruction : The deck must be preset for the installation of the cleat frame and for its hidden part under the deck ( gas springs housing). The sliding (4) rods are watertight. Solimar will provide a drawing complete of all the technical information about the drilling assembling of the bolts and of the cylinders (5) through the deck. Warning: for a better load distribution on the deck we recommend you to perform the holes of the cylinders with accuracy ( +0,3/+0,5)
Flush cleat in closed position
The frame of the cleat must be glued on the deck by using epoxy glue (or similar), smearing the product as showed in the picture (2) (marked with red colour). Before applying the glue you must clean and degrease the surfaces. The cylinders (5) have to be coated with glue as showed on picture (2) (deck thickness)
Pict. 3
Pict. 1
Pict. 2
Full concealed pop up cleats Solimar is happy to present to our old and new customers a new line of cleats made of Light Alloy, of stainless steel 316 and Titanium with the features below. Just use your foot to open and close the cleat, it is concealed and flush with the deck! The gas springs will pop up the cleat for you and stop it in the opened position. Operation The cleat is designed for the fully automatic opening through pushing the cleat with a foot or a hand (both for opening and closing). No buttons or levers for opening or closing. Tested for 10,000 cycles.
A
B
I
HG
DE
F
C
STAINLESS STEEL
A B C D E F G H I Load (kg)
091T200 216 71 200 28 45 20 93 105 35 2300/3500
091T250 266 76 250 30 57 23 110 125 40 4000/5300
091T300 316 91 300 34 65 25 124 140 50 9500/11100
091T350 366 96 350 36 78 27 141 160 55 10700/12600
091T450 468 93 450 34 95 25 130 165 70 12300/14000
ALUMINIUM
A B C D E F G H I Load (kg)
091T200L 216 71 200 28 45 20 93 105 35 1500
091T250L 266 76 250 30 57 23 110 125 40 2300
091T300L 316 91 300 34 65 25 124 140 50 4250
091T350L 366 96 350 36 78 27 141 160 55 5300
091T450L 468 93 450 34 95 25 130 165 70 6400
Solimar can change some dimensions if it is necessary
091B
091T
STANDARD
DrainagePict. 4
2
3
3a
4
6
7
8
910
Drainage
5
Pict. 2
Pict. 1
Flush cleat in closed position
TECHNICAL ASSEMBLING INSTRUCTIONS FOR FLUSH CLEATS
List of the components: 1 Horizontal beam of the cleat (securing mooring ropes) 2 Cleat frame 3 Slot for the spanner to assembly/disassembly of the rod 3a Slot for the spanner to assembly/disassembly of the gas
spring cylinder 4 Cleat rod 5 Gas spring cylinder 6 Under deck counter plate (on request) 7 Locking bolts 8 Deck 9 Teak deck 10 Seal rubber
Solimar will provide a drawing complete of all the technical information about the drilling assembling of the bolts and of the cylinders (5) through the deck. Warning: for a better load distribution on the deck we suggest you to perform the holes of the cylinder with accuracy (+0,3/+0,5)
Assembling instruction : The deck must be preset for the installation of the cleat frame and for its hidden part under the deck (gas springs housing). The sliding rods are watertight. On the deck, you must preset the drainages for the water exit from the cleat frame. Before to fit the cleat on the deck you have to check , (when the cleat is in working position), if it is possible to put the locking bolts through the holes. Only if this step is not possible, you have to unscrew the rods (4), to rotate the beam of the cleats and to fit the bolts through the locking holes. The frame of the cleat must be glued in the recess preset on the deck by using epoxy glue (or similar), smearing the product as showed in the picture (3) (marked with red colour). Before applying the glue you must clean and degrease the surfaces. The cylinders (5) have to be coated with glue as showed on picture (2) (deck thickness) Warning : the frame (2) must matches perfectly to the supporting recess surface. After the assembly of the frame (2) fit the bolts and tighten securely the nuts below the counter plate under the deck. We recommend you to protect the bolts with anti-corrosion grease. You can now complete the installation with the laying of the rubber in the slot (5-6mm. thickness) all around the cleat frame.
The frame of the cleats is fully flush. The central raised shape of the beam (1) allows to open/close easily the cleat with a slight pressure of the hand or of the foot. The cleats are available made of AL6082, A304-316 stainless steel and the finishing can be: mirror polished, peening, silver anodizing, black or grey hardkote anodizing.
The new flush cleat combines aesthetics and functionality.
Drainage
2
3
4
5
6
7
3a
1
Pict. 3
A A
SEZIONE A-A
1
23
3a
4
56
78
9
10
Pict. 5
C
D
A
B
E
F
1
2
3
7
48 6
5
SPECIFICATION SHEET
Material Finishing
1 AISI 304/316 Mirror polished
2 AISI 304/316 Mirror polished
3 AISI 304/316 Mirror polished
4 AISI 304/316
5 LIGHT ALLOY
6 AISI 304
7 AISI 304
8 AISI 304
A B C D E F
093B400 400 135 187 20 130 100
093B500 500 160 220 20 160 120
MODELS FEATURES
Description
093A With locking bolts
093B With hidden locking bolts
093C Without locking bolts, welded to the deck
B
A
D
H
CE
G
F
Solimar can change some dimensions if it is necessary
A B C D E F G H
090A480 480 100 128 25 12 187 165 215
CUSTOM x x x x x x x x
Solimar can change some dimensions if it is necessary
Just use your foot to open and close the cleat, it is concealed and flush with the deck! The gas springs will pop up the cleat for you. Available in stainless steel, aluminium and titanium .
CUSTOM
STANDARD
A
ASEZIONE A-A
60
300
60
4729
160
A
A
SEZIONE A-A
B
B
SEZIONE B-B
300
176
60
47
60
30
STANDARD
STANDARD
STANDARD FAIRLEADS
FAIRLEADS WITH SHEAVES
It is a very useful item to organize your mooring ropes. A technical item designed to match smartly on your deck. It is available in many versions and different sizes, materials and finishing: AL6082 (L series), Stainless steel A304-316,
Titanium Mirror polished, Silver, Hardkote anodization,
Peening
It is available in many versions and different sizes, materials and finishing: AL6082 (L series), Stainless steel A304-316,
Titanium Mirror polished, Silver, Hardkote anodization,
Peening Sheave: Ertalyte, Aluminium, Stainless steel A304-316 Sliding on bronze selflubricated bushing
Max Dimensions
059A200 200 x 50
059A260 260 x 60
059A300 300 x 60
059A340 340 x 70
Max Dimensions
059AR200 200 x 50
059AR260 260 x 60
059AR300 300 x 60
059AR340 340 x 70
A
A SEZIONE A-A
B
B
SEZIONE B-B
100
240
147
60
30
B
B
SEZIONE B-B
200
240
CUSTOM
RECESSED FAIRLEADS SERIES WITH SINGLE / DOUBLE SHEAVE (Installation only on preset toerail)
FOR THE CONDITIONS OF SALE AND WARRANTY, PLEASE REFER TO THE SOLIMAR WEBSITE www.solimar.it
It is a very useful item to organize your mooring ropes. A technical item designed to match smartly on your deck. It is available in many versions and different sizes, materials and finishing: Aluminium 3571, Stainless steel A304-316, Titanium Mirror polished, Silver, Hardkote anodization, Peening Sheave: Ertalyte, Aluminium, Stainless steel A304-316 Sliding on bronze selflubricated bushing
059S
059D
CUSTOM
FIXED OR SCREWED FAIRLEADS
Fully custom fairlead, available in many materials and finishing: Stainless steel A316,
mirror polished Titanium, peening Aluminium-bronze,
mirror polished
