of 64
8/3/2019 Lecture 5 6 7 PN
1/64
Lecture 5
8/3/2019 Lecture 5 6 7 PN
2/64
P-N Junctions Part 1: Concepts, Charges and Fields
The most basic device of microelectronics, the P-N junction
8/3/2019 Lecture 5 6 7 PN
3/64
8/3/2019 Lecture 5 6 7 PN
4/64
8/3/2019 Lecture 5 6 7 PN
5/64
8/3/2019 Lecture 5 6 7 PN
6/64
8/3/2019 Lecture 5 6 7 PN
7/64
8/3/2019 Lecture 5 6 7 PN
8/64
8/3/2019 Lecture 5 6 7 PN
9/64
8/3/2019 Lecture 5 6 7 PN
10/64
Vbi has nothing to do with voltages that are applied via external batteries or power
supplies
Vbi is spontaneous internal voltage developed by the rearrangement of holes &
electrons!
8/3/2019 Lecture 5 6 7 PN
11/64
Now know the energy / voltage step formed - But have no handle on how wide the "depletion layer"
is
The NET charge in the depletion layer (between the p and n regions) is now due acceptors & donorsalone
8/3/2019 Lecture 5 6 7 PN
12/64
8/3/2019 Lecture 5 6 7 PN
13/64
8/3/2019 Lecture 5 6 7 PN
14/64
8/3/2019 Lecture 5 6 7 PN
15/64
8/3/2019 Lecture 5 6 7 PN
16/64
8/3/2019 Lecture 5 6 7 PN
17/64
8/3/2019 Lecture 5 6 7 PN
18/64
But from equation 6
using this and equation 6 to solve for xp:
8/3/2019 Lecture 5 6 7 PN
19/64
8/3/2019 Lecture 5 6 7 PN
20/64
8/3/2019 Lecture 5 6 7 PN
21/64
8/3/2019 Lecture 5 6 7 PN
22/64
8/3/2019 Lecture 5 6 7 PN
23/64
All of the Above: No external voltages applied!! Vbi is an internal, naturally generated,
voltage
8/3/2019 Lecture 5 6 7 PN
24/64
NOW FOR THE FIRST TIME: Apply an external voltage (with a battery or DC
power supply) end to end:
1) Apply "Reverse Voltage" Reversed in the sense: + Applied to N-side
- Applied to P-side
Remember that Voltage = Potential Energy per positive charge = opposite of ourelectron bands
So positive voltage pulls DOWN electron energy
8/3/2019 Lecture 5 6 7 PN
25/64
8/3/2019 Lecture 5 6 7 PN
26/64
8/3/2019 Lecture 5 6 7 PN
27/64
What has changed from previous case with our application of Vreverse?
Just have wider regions of exposed Na- and Nd+
So parabolic profiles simply extend longer and steps become higher!
8/3/2019 Lecture 5 6 7 PN
28/64
So with that justification get revisions:
8/3/2019 Lecture 5 6 7 PN
29/64
2) Apply Forward Voltage: Forward in the sense: + Applied to P-side- Applied to N-side
8/3/2019 Lecture 5 6 7 PN
30/64
8/3/2019 Lecture 5 6 7 PN
31/64
Calculate Capacitance of this junction:
8/3/2019 Lecture 5 6 7 PN
32/64
8/3/2019 Lecture 5 6 7 PN
33/64
P-N Junction Current / Equation for Diode with Thick Layers
Calculate current density, J, across the diode as a function of the applied voltage
1) Assume "Steady-State
Vapplied constant in time (or has been at present value a "long" time)
Then total current, Jtotal = Jp + Jn, must be constant throughout the diode
8/3/2019 Lecture 5 6 7 PN
34/64
This is assumed OUTSIDE the depletion region (W)
Inside the depletion layer has been massive change in majority carrier concentration-they are all gone
8/3/2019 Lecture 5 6 7 PN
35/64
8/3/2019 Lecture 5 6 7 PN
36/64
8/3/2019 Lecture 5 6 7 PN
37/64
8/3/2019 Lecture 5 6 7 PN
38/64
Assumption 3) All carriers that start across the junction make it to the other side
Electric field pushes minority carriers across
Will move so fast have no time to recombine!
MAJORITY Carriers: Because minority carriers (above) whip across junction, thereare ~ 0 there at any time~ Nothing for majority carriers to recombine WITH! Majority also likely to makeacross
8/3/2019 Lecture 5 6 7 PN
39/64
NOTATION
8/3/2019 Lecture 5 6 7 PN
40/64
If ~ all carriers make it across => same density of electrons on both sides /
same density of holes on both sides
Restate arguments (for electrons)
8/3/2019 Lecture 5 6 7 PN
41/64
Restate arguments (for electrons)
Form of both of these equations:
8/3/2019 Lecture 5 6 7 PN
42/64
Form of both of these equations:
If Vapplied were turned off (=> 0), go back to overall equilibrium
But in strict equilibrium, we KNOW what the minority carrier concentrations (left sides) are
8/3/2019 Lecture 5 6 7 PN
43/64
8/3/2019 Lecture 5 6 7 PN
44/64
Plug equations 3 and 4 into equations 1 and 2, respectively
Or graphically
8/3/2019 Lecture 5 6 7 PN
45/64
Remember the "Minority Carrier Continuity Equations" Time to put them to truly
8/3/2019 Lecture 5 6 7 PN
46/64
Remember the Minority Carrier Continuity Equations Time to put them to trulyuseful work
8/3/2019 Lecture 5 6 7 PN
47/64
8/3/2019 Lecture 5 6 7 PN
48/64
"Thick Diode" or more precisely, "Thick Layer" Case
If layers are thick compared to diffusion lengths:
One term falls to zero Makes sense: carriers diffuse deeper and recombine
One terms goes to Makes NO sense: minority carriers increasing awayfrom junction
Solution is to set coefficient of growing terms equal to zero (B=0 and D=0 above)
8/3/2019 Lecture 5 6 7 PN
49/64
8/3/2019 Lecture 5 6 7 PN
50/64
8/3/2019 Lecture 5 6 7 PN
51/64
Diode with THIN layers
8/3/2019 Lecture 5 6 7 PN
52/64
y
At least one side of a diode is much THINNER than diffusion length of itsminority carriers!!
Comes from the way real diodes are made:
1) Start with layer (either thick or thin) of one type
of semiconductor
2) Implant other dopant short distance into surface:
3) P-dopant penetrates very short distance
(1 micron or less)
but in high concentration that overwhelmsN-type dopant:
In an integrated circuit, layer below may have been created same way
8/3/2019 Lecture 5 6 7 PN
53/64
In an integrated circuit, layer below may have been created same way=> BOTH layers "thin"
How do we deal with this? Go back to last lecture at point we had derivedgeneral minority equations
8/3/2019 Lecture 5 6 7 PN
54/64
Now assume P-layer on left is much thinner than Ln:
Then where ever we are in the left layer ( x < xp), we know that in the exponentxp + x is
8/3/2019 Lecture 5 6 7 PN
55/64
-"The Law of the Junction":
Would then know the slope if we could figure out value at LEFT face of P-layer
(the surface)
Front surface of crystal = excellent place for minority carriers to recombine(like continuous "traps"
8/3/2019 Lecture 5 6 7 PN
56/64
(like continuous traps
Can thus assume excess electron concentration => 0 at surface. If P-layerthickness is xp_layer:
where np(-xp) is theConstant
Use this minority carrier profile to calculate the diffusion (gradient driven)current of minority carrier electrons
8/3/2019 Lecture 5 6 7 PN
57/64
current of minority carrier electrons
8/3/2019 Lecture 5 6 7 PN
58/64
plugging in boundary condition
Evaluate this equation at x = -xp to get electron current flowing across junction
Then need hole current flowing across junction into the N-layer to get total current indiode:
if N-layer is thick (as have assumed to this point and already derived
8/3/2019 Lecture 5 6 7 PN
59/64
or a ayer, use sma er o wo: s m nor y carr er us on eng s un ep e e
thickness
REAL DIODES
8/3/2019 Lecture 5 6 7 PN
60/64
REAL DIODES: Must also take into account
1) FORWARD BIAS (lowered step => high current in junction)
1a) Recombination of carriers within the depletion region
- Are so MANY crossing at any moment that there ARE plenty to
recombine with- So expect some recombination, and thus loss of current within thejunction!
1b) Resistive loss in thick layers
We apply voltage at both ends of the diode
8/3/2019 Lecture 5 6 7 PN
61/64
pp y g
But as with right N-layer (thick), that face is a LONG wayaway from junction
Current flowing thorough thick layers => resistive voltage
drop
Voltage at junction is thus reduced below full applied voltage!
2) REVERSE BIAS (increased step and Wdepletion, very large electric fields)
2a) Thermal generation in thickened depletion layer
Depletion region can become quite thick (1.6 microns at -20 Volts in
example above)
There is still heat!Heat => Generation of new carriers - electrons boiling out of valence
band to conduction band
Can thus get INCREASE in current as it crosses the depletion region!
8/3/2019 Lecture 5 6 7 PN
62/64
2b) Tunneling "Zener Breakdown"
8/3/2019 Lecture 5 6 7 PN
63/64
Abrupt increase in reverse current, depends on junction width - which in turndepends on doping
2c) Breakdown due to avalanche multiplication of carriers crossing junction
8/3/2019 Lecture 5 6 7 PN
64/64
Electrons and holes are "falling" over energy step
Where is their lost energy going? Energy => crystal lattice
THIS energy can be used to create new pairs of electrons and holes
=> More electron / hole flow
=> More dissipated energy
=> More electrons and holes AVALANCHE!
Once it starts, multiplies VERY rapidly (as in real avalanche) => Similar abrupt
increase in reverse current!