Date post: | 07-Mar-2016 |
Category: |
Documents |
Upload: | glen-raymond |
View: | 258 times |
Download: | 13 times |
Product Catalogue No 5Automotive Marine Industrial
LED Technologies Excellence in Lighting Solutions
Designers and Manufacturers
Products made in Australia and Taiwan
2 Information Correct at time of printing
LED TEchnoLogiEs sETs prEcEDEncE
The Federal Court of Australia recently handed down a decision in the case of LED Technologies Pty Ltd v Elecspess Pty Ltd, Ren Pty Ltd, Olsen Pty Ltd and Advanced Automotive Australia Pty Ltd, which highlights the benefit of obtaining design registrations for any new products.
The case was also one of the first to consider the infringement test under the new Designs Act 2003. LED Technologies is a manufacturer and importer of automotive LED products. It developed and designed a new and distinctive looking square shaped automotive tail lamp which it manufactured in Taiwan and obtained Design Registrations. Elecspess obtained a similar looking but not identical product made in China with the brand name of ''CONDOR'' and offered it for sale in Australia. LED Technologies Pty Ltd brought an action against Elecspess and other's for design infringement. Justice Gordon of the Federal Court of Australia ruled in favour of LED Technologies and issued injunctions for the prevention of further sales and awarding $200,000 in damages with legal cost's expected to be up to $1,200,000. In her judgment, Justice Gordon considered and found that any product which embodied designs that are substantially similar in overall impression to a registered design would infringe the design registrations. The product does not have to be identical to the design registration. In assessing the similarities, the Court would only have regard to the visible features of the design and would do this by looking at both the infringing product and the registered design. Accordingly, the material used to manufacture the product or the inner workings of the product is irrelevant for design infringement purposes.
On appeal three Federal court Judges, Justice Jessup, Justice Besanko and Justice Emmett dismissed the appeal by Elecspess, Ren, Olsen and Advance Automotive appeal from Justice Gordon’s ruling that it had infringed LED Technologies registered design.This is the first substantive decision by a Full Court on the new Designs Act introduced in 2003 and provides a guideline and reference for any future design infringement cases.
Owner of LED Technologies Tony Ottobre’s comments were, this is a fantastic result for all designers of original products who can now use this case as a precedence and a blow for product copiers.
3Information Correct at time of printing
Screw fasteningBeam adjustment
Austrailian warehouse and distribution
Taiwanese Assembly Plant and Testing Equipment
Australian Personnel
DISCLAIMERLED Technologies Pty. Ltd. have made every effort to ensure that the information contained in this catalogue is correct and accurate; current information should be checked at the time of placing an order and before any manufacturing/installation is to be commenced. Measurements provided are accurate at the time of publication; we advise measurements should be confirmed before final decisions/installations are made. LED Technologies Pty. Ltd. reserves the right to improve, modify, make dimensional design and technical changes or discontinue or update designs without prior notice; although we will take all measures to inform our customers if and when possible of any changes made.LED Technologies Pty. Ltd. will not accept liability of any kind due to misuse or abuse of any products not used as intended.
Date of Printing April 2011
European Personnel Taiwanese Partners
Australian assembly line
Laser engraving
Ultra sonic welding Vibration welding
Glue dispenserGlue supply system
Epoxy glue system
Air tight testing
Hot melt glue
4 Information Correct at time of printing
Made in Melbourne
AUSTRALIA
creating the future in lighting
a first for australian Manufacturing.
the first leD rear combination lamp made in australia.
unconditional 5 Year Warranty.
aDr compliant for horizontal and Vertical applications
MaXileD rear combination go to Page 18
•
•
•
•
LED Technologies, manufacturers of LED Autolamps, have begun manufacturing the all new MaXiLED Stop/Tail/Indicator and Reverse lamp. A first in Australia and certified to proudly carry the “Made in Australia” logo. Using only quality components and plastics sourced from overseas suppliers and utilizing our own full SMD/component assembly line to fit out, solder and testing of circuit boards. The finished boards are then fitted to the base, fully potted and sealed against water and dust ingress then assembled with specially designed chrome inner reflectors, honey comb designed lens with reflex reflectors. The finished lamps are then fully tested and packaged into the LED Autolamps blister clamshells.
Australian designed
Premium components
SMD LEDs
Multi voltage
High quality plastics
Superior sealing methods
Fully submersible
Intelligent manufacturing
Manufacturing control
Quality control
Tests exceeds standards
5Information Correct at time of printing
6 Information Correct at time of printing
Large Trailer harness systemLED Technologies has developed an 8 wire cable system to suit any Truck Trailer world wide, we have also manufactured and patented a plug ring to make the complete system waterproof. The T piece is a magnificent product manufactured with a PCB - 8 pins going in, 6 pins left and 6 pins right going out. Encased in a hardened PVC plastic which is resistant to fire and water.The main cable is 9mm in diameter and comes in various lengths from 6 meters to 15 meters, each cable has a junction box in the middle of its length which provides plugs for the side direction indicator and for side marker lamps, at one end there is an 8 pin plug which connects to the T piece, at the other end there are 8 coloured wires for connection to the main trailer plug.Both left and right cables are 1.2m long and have up to six wires that connect to the rear combination. This cable is 9mm in diameter with a 6 pin plug which also has our round and square marker plugs to suit our marker lamp system.
Available products with the Large Trailer harness system
J3 Series see page 19
MaXilamps see page 30-31
Quad Square Series see page 24
Lumilamp see page 29
8PTP T piece6PR1.2 RHS Plug & cable6PL1.2 LHS Plug & cable8P6 6 metre main cable8P9 9 metre main cable8P12 12 metre main cable8P15 15 metre main cable
Red StopWhite EarthPink ReverseBlue Fog or AccessoryBrown RHS TailGreen RHS IndicatorYellow LHS Indicator Black LHS Tail
Part Numbers and Product Description
nEW
PRODUCT
7Information Correct at time of printing
LED Technologies has developed a 2 wire cable system for marker lamps and licence plate lamps, we have included 4 types of markers with this system which gives you a choice of which marker to use. The simplicity of this system is that there is no cutting splicing or joining of wires, we have developed two plugs, one round for earth and one square for power. Included is a T piece
with round and square plugs - the entire system is fool proof, because you cant fit a round plug into a square hole and
vice versa. The cable lengths vary from 1 metre to 5 metres and whenever you need to add a marker
or licence lamp just add the T piece.All plugs and T piece are made from
PVC which is fire and water resistant. We also developed
a special water proof patented ring and as it suggests the whole system is water proof with a rating of IP67.
Marker Lamp harness system
nEW
PRODUCT
Available products with the marker lamp harness system
35 Series see page 44
35 Series Licence plate see page 52
58 Series see page 45
44 Series see page 48
36 Series see page 44
2CPT T piece2C100 1 metre 2 pin cable2C200 2 metre 2 pin cable2C300 3 metre 2 pin cable2C400 4 metre 2 pin cable2C500 5 metre 2 pin cable
Part Numbers and Product Description
8 Information Correct at time of printing
The requirements specified in the ADRs for the performance and installation of lamps and reflectors are based on international standards.The performance requirements usually involve tests done in a laboratory to show compliance. Trailer manufacturers must ensure that the lamps and reflectors fitted to their trailers comply with these performance requirements.Lamps on a trailer must not show red light to the front or white light to the rear. Two front position lamps showing white light to the front of the trailer must be fitted to trailers which are more than 1600 mm wide.Two rear position lamps showing red light to the rear must be fitted to each trailer. One rear registration plate lamp must be fitted to each trailer. Two stop lamps showing red light to the rear must be fitted to the trailer. Two direction indicator lamps showing amber light to the rear must be fitted to the rear of each trailer. The flashing rate of the indicators must be within the range of 60 to 120 flashes per minute.Two end-outline marker lamps showing white light to the front and two lamps showing red light to the rear must be fitted to trailers more than 2.1 metres wide. Two side marker lamps showing amber light to the front and red light to the rear must be fitted on each side of trailers over 2.1 metres wide or having a total length over 7.5 metres.If a trailer is over 7.5 metres in total length an additional side marker lamp must be fitted on each side midway between the front and the rear lamps. If a trailer such as a boat trailer has no structure at the front and at the rear to which end-outline marker lamps can be attached then fitting one end-outline marker lamp midway on each side is acceptable.Reflex reflectors are reflectors of a conventional lens type and must comply with ADR 47/00. Two white reflectors must be fitted to the front of each trailer. The number of amber coloured side reflex reflectors that must be fitted to each side of a trailer depends on the total length of the trailer including its draw bar. At least one reflector must be fitted to the middle third of the total trailer length. There must be a reflector within 3 metres of the front of the trailer and a reflector within 1 metre of the rear of the trailer. The distance between adjacent reflectors must not exceed 3 metres. Two reflectors which reflect red light to the rear must be fitted to the rear of each trailer.The ADR Installation of Lighting and Light-signalling Devices is available at the RVCS website at www. rvcs-prodweb.dot.gov.au Click on the Australian design rules tab and click on the ADR 13/00 document.
ADr MiniMuM rEquirEMEnTs
ADR
9Information Correct at time of printing
ADR 47/00Front Reflex Reflectors
ADR 49/00Front Position Lamps
ADR 49/00Front End Outline Lamps
ADR 49/00Rear End Outline Lamps
ADR 47/00Side Reflex Reflectors
ADR 45/01 or ADR 74/00Side Marker Lamps
ADR 49/00Stop Lamps
ADR 49/00Rear Position Lamp
ADR 48/00Licence Plate Lamps
ADR 6/00 Cat. 5 or Cat. 6Supplementary Side DirectionIndicator Lamps
ADR 6/00 Cat. 2Rear Direction Indicator Lamps
ADR 47/00Rear Reflex Reflectors
ADR 6/00 Cat. 1Front Direction Indicator Lamps
ADR 1/00Reversing Lamps
10 Information Correct at time of printing
REAR COMbInATIOn LAMPS 14-31
SQUARE LAMPS 33
RECTAnGLE LAMPS 34-35
STRIP LAMPS 32-35
RECESS LAMPS 36-37
ROUnD LAMPS 38-41
ObLOnG LAMPS 42
FROnT InDICATOR LAMPS 43
MARKER LAMPS 44-51
LICEnCE PLATE LAMPS 52
MARInE LAMPS 53
WORK LAMPS 54-57
EXTERIOR LAMPS 58-59
InTERIOR LAMPS 59-62
CAT 6 SIDE DIRECTIOn InDICATOR 63
CARAVAn DOOR EnTRY 64
HAnD LAMPS 64
COLOURED LAMPS 65-66
EMERGEnCY LAMPS 67
EMERGEnCY bEACOnS 68-70
TRAFFIC SIGnAL LAMPS 71
DAYTIME RUnnInG LAMPS 72
YELLOW LIGHT LAMPS 73
REFLECTORS 74
FLASH UnITS 75
COnVERTERS 76
PILOT LAMPS 76
LOAD RESISTORS 76
PROMOTIOnAL PRODUCTS 77-78
MERCHAnDISERS AnD DISPLAYS 79-86
WARRAnTY, RETURn FOR CREDIT FORM 87
TABLE oF conTEnTsPAGES
11Information Correct at time of printing
Part No.
Page No.
Part No.
Page No.
Part No.
Page No.
Part No.
Page No.
proDucT nuMBEr AnD pAgE
100AM 33100AMB 33100ARM 15100ARM10 15100B1B 33100B1BB 33100B1C 33100B3BB 23100B3CB 23100B3WB 23100B4BB 24100BAARRM 24100BAR 15100BAR10 15100BAR2 15100BARB 15100BARLP2 15100BARRM 23100BARRWM 24100BARWM 23100BSTIM 20100CARRM 23100CARWM 23100CSTIM 20100RM 33100RMB 33100WM 33100WMB 331004ARM 511004L 511004R 5110121 6010121/24 6010121/24Opaque 6010121/Opaque 601016 601016/24 601016/24Opaque 601016/Opaque 60101BAR 14101BAR10 14101BAR2 14101BARLP 14101BARLP2 14102A 38102AC 38102AM 38102R 38102RC 38102RM 38102W 38102WM 381031 601031/24 601031/24Opaque 601031/Opaque 601061 601061/24 601061/24Opaque 60
1061/Opaque 6010CB 60110AM 38110AMB 38110RM 38110RMB 38110WM 38110WMB 38111AM 68111RM 68111WM 68112ABM 68112RBM 68125AM 33125AMB 33125B1B 33125B1C 33125B3BB 23125B3C 23125BARML 21125BARMR 21125BARRM 23125BARWM 23125CARRM 23125CARWM 23125RM 33125RMB 33125WM 33125WMB 3312571 4912572 4912611 4912612 4912761 5112781 51127AMF 69127RMF 69127BMF 69127GMF 69127AMM 69127WMM 691282A 501282R 501284A 501284R 50130AM 37130AMB 37130RM 37130RM-1 37130RMB 37130RMB-1 37130WM 37131RM 36131CRM 36131AM 36131CAM 36131WM 36135AM 35135AMG 35
135ARM 28135ARMG 28135BKT 29135BKT-1 35135CARRM 29135CARWML 29135CARWMR 29135CAT1 43135CAT124 43135CAT1G 43135G 35135RM 35135RMG 35135WM 35135WMG 351369A 501369R 501374A 491374R 491388A 491388R 491388W 49140STILM 29140STIM 29143120B12 59143120B24 59143120C12 59143120C24 59143120G12 59143120G24 59143120W12 59143120W24 59143ILB12 59143ILB24 59143ILC12 59143ILC24 59143ILG12 59143ILG24 59143ILW12 59143ILW24 59143RWB 53143RWW 531440A 491440R 491440W 491458AM 501458ARM 501458BC 501458RM 501458WM 501459A 491459R 491474A 491474R 491474W 491477A 511477R 511479A 511479R 51
148BW12 61148GW12 61148WW12 611490AM 481490RM 481490WM 481491AM 481491RM 481491WM 48150ARM 15150ARM10 15150BAR 15150BAR10 15150BAR2 15150BARB 15150BARLP2 15151BAR 14151BAR10 14151BAR2 14151BARLP 14151BARLP2 141685AB 501685AM 501685RB 50175AW 43181AME 51181RME 51181WME 51182AM 69182RM 69182WM 69200B1B 34200B1C 34200B2B 34200B2C 34200B3B 34200B3C 34200BAAAM 34200BAAM 34200BAM 34200BAMB 34200BARLM4 26200BARLPM2 25200BARM 25200BARM4 26200BARM6 26200BARRM 26200BARWM 26200BKT4 26200BKT6 26200BRM 34200BRMB 34200BRRM 34200BRRRM 34200BRWM 25200BSTIM 25200BSTIMB 25200BSTIR48 25200BSTIRMB 25
12 Information Correct at time of printing
Part No.
Page No.
200BWM 34200BWMB 34200CAAAM 34200CAM 34200CARM 25200CARRM 26200CARWM 26200CAW 43200CAW/24 43200CRM 34200CRRRM 34200CSTIM 25200CWM 34207A12 34207BAR4 26207BAR6 26207BARL 25207BARL4 26207BARLP2 25207BARP 25207R12 34235A12 32235A24 32235BAR12 28235BB 28235CAR12 28235CB 28235R12 32235R24 32235W12 32235W24 32235WAR12 28235WB 28240152C 62240152W 62250ARWM 18250ARWMB 18250RARM 18250RARMB 18275ARM 16275BAR 16275BAR2 16275BARB 16275GARWM 18275RARWM 1825A12 3225R12 3225W12 322C100/2 72C100B10 72C200/2 72C200B10 72C300/2 72C300B10 72C30B10 72C400B 72C500B 72PT10 72PT2 7305A12 65305B12 65
305G12 65305R12 65305W12 6530BLM 5230CLM 52312482C 62312482W 623591 5135AM 44,6435AM2 4435AMB 4435ARM 4435ARM2 4435ARMB 4435BB 4435BC 4435BCB 4435BL 5235BLM 5235BLM1P 5235BLM6 5235BLMB 5235BLMB2P 735BM 6435BW 4435CAM 4435CAMB 4435CARM 4435CARMB 4435CL 5235CLM 5235CLMB 5235CRM 4435CRMB 4435CWM 4435CWMB 4435GM 6435PM 6435RM 44, 6435RM2 4435RMB 4435WM 44, 6435WM2 4435WMB 4435YM 6436AM 4436RM 4436ARM 4436WM 4436CAM 4436CRM 4436CARM 4436CWM 4438AM 4638AMB 4638AMBKT 4738AMMB 4738ARM 4638ARMB 4638ARMBKT 4738ARMBKTB 47
38ARMBKTR 4738ARMMB 4738BB 46-4738CAM 4638CARM 4638CARMB 4638CB 46-4738CRM 4638CWM 4638RM 4638RMB 4638RMBKT 4738RMMB 4738WM 4638WMB 4638WMBKT 4738WMMB 47380A12 32380A24 32380BAR 28380BB 35380CA12 35380CAR 28380CB 35380CEL 63380CR12 35380R12 32380R24 32380W12 32380W24 32380WB 35380WEL 6342AMB 4542ARMB 4542CAMB 4542CARMB 4542CRMB 4542CWMB 4542RMB 4542WMB 4544AME 4844AMEB 4844AMEB2P 744RME 4844RMEB2P 4844WME 4844WMEB2P 4844WAME 4844WRME 4844WWME 484C110C 174C130C 174C150C 174C170C 174C190C 174C210C 174C30B 174C320B 1750SAM 6650SBM 6650SGM 66
50SRM 6650SWM 665100W12 585100W24 5852CG 5352CR 5352CW 5352WG 5352WR 5352WW 5353101 38-3953101B 38-3953101C 38-3953101H 38-3953102 36-3953102H 36-3954101 425437A 415437R 415437W 415503A 425503R 425505W 4255062 425513A 405513R 405513W 405523A 395523R 395525W 395526A 705533A 425533R 425535W 425543A 415543FA 405543FR 405543FW 405543R 415543W 415563A 425563R 425563W 425570A 395570R 395570W 395575A 395575R 395575W 395585A 405585R 405585W 405590AM 365590RM 365590WM 3658AM 4558AM3 4558AMB 4558AMB2P 758AMEB 758ARM 45
Part No.
Page No.
Part No.
Page No.
Part No.
Page No.
13Information Correct at time of printing
Part No.
Page No.
Part No.
Page No.
Part No.
Page No.
Part No.
Page No.
58ARM3 4558ARMB 4558ARMB2P 758CAM 4558CAM3 4558CAMB 4558CARM 4558CARM3 4558CARMB 4558CRM 4558CRMB 4558CWM 4558CWM3 4558CWMB 4558RM 4558RM3 4558RMB 4558RMB2P 758WM 4558WM3 4558WMB 4558WMB2P 759101 36-3759401 36-3759401B 36-3759401C 36-3759401H 36-375940A 375940R 375940W 37595384W 62595384C 625C1200B 175C21 175C370C 175C41 175C430C 175C490C 175C550C 175C610C 175C670C 175C730C 175C800B 175C81 176434BWM 526434CWM 526505BM 646505GM 646505IM 646505OM 646505PM 646505RM 646505WM 646505YM 6465362 5268B 6568G 6568I 6568O 6568P 6568R 65
68W 6568Y 657030A 737030AB 737030R 737030R-1 737030RB 737030W 737030WB 737035A 737035AB 737035R 737035RB 737035W 737035WB 737150BM 547150WM 547208MR 567208MS 567210M 567220M 567450B12 557450B24 557450W12 557450W24 557451BM 557451WM 557524 587524/Opaque 587524C 587524G 587524W 587524WB 587524WR 587530 587530/Opaque 587530C 587530G 587530W 5875C 5875CLB 6575CLG 6575CLI 6575CLO 6575CLP 6575CLR 6575CLY 6575G 6575W 657790BM 547790WM 5479BWR12 6179CWR12 6179GWR12 6179SWR12 6179WWR12 6180AB 3380AM 3380AMB 3380B1BB 3380B1CB 33
80B2BB 2180B2C 2180B3B 2280B3BB 2280B3C 2280B3CB 2280B3SKT 2280B4BB 2380BAARRM 2480BAR 2180BARM 2180BARR 2280BARRM 2280BARRWM 2480BARRSKT 2280BARW 2280BARWM 2280BARWSKT 2280BKT 2280BSTIM 2080BSTIMB 2080C3SKT 2280CAR 2180CARM 2180CARR 2280CARRSKT 2280CARRM 2280CARW 2280CARWM 2280CARWSKT 2280CSTIM 2080RB 3380RM 3380RMB 3380WB 3380WM 3380WMB 338PTP 66PR1.2 66PL1.2 68P6 68P9 68P12 68P15 683A 7083G 7083R 7084DTRM 718514BM 57856BM 57858BM 5793AM 6693BM 6693GM 6693RM 6693WM 6694AM 6694BM 6694RM 6694WM 66ACDC1 74
BC1000 17BC1200 17BC600 17BC800 17BCC1 17DB1 85DB2 85DB3 85DB4 85HH1061/12 63HH1061/240 63J3AM 19J3B3B 19J3BARRM 19J3BARWM 19J3BRRRM 19J3RM 19J3WM 19J9B9B 27J9B9C 27J9BARRM 27J9BARWM 27J9CARRM 27J9CARWM 27J9WRAM 27LP1 52LP100 15LP100M 15LP101 14LP150 15LP150M 15LP151 14LP1B 52LR12/2 75LR24/2 75LUMILAMP2 29LUMILAMPLB 29LUMILAMPRB 29MaXilamp1XC 31MaXilamp1XRE 30Maxilamp3XC 31MaxiLamp3XCW 31MaXilamp3XR 30MaXilamp3XRB 30Maxilamp3XRR 30MaxiLamp5XC 31MaxiLamp5XCW 31MaXilamp5XR 30MaXilamp5XRB 30Maxilamp5XRR 30PLA12 75PLB12 75PLG12 75PLR12 75PLW12 75SFU1 74
14 Information Correct at time of printing
Product Description: These lamps are fully submersible, rust proof, shock resistant and feature our square lens pattern with 8 high brightness LEDs.
Part no 151BAR 151BAR2 151BAR10 151BARLP2
Voltage: 12 Volt 12 Volt 12 Volt 12 Volt
Cable: 40cm 40cm 10 metre cable 40cm
Packaging: Box Blister of 2 Poly Bag Blister of 2 with licence
Current: @13.8Volts (Stop-0.13Amps) (Tail-0.04Amps) (Ind-0.12Amps) (Licence-0.03 Amps) - @28Volts (Stop-0.12Amps) (Tail-0.06Amps) (Ind-0.07Amps)
C.R.n: This lamp complies with ADR under ECE approval 01 2a, 02 R1-S1, 02 1A (Component number 6362), Licence (L 00 Component number 6110)
Fitting: Surface mount onto flat surface vertically with Indicator at top using bolts in back of lamp, run wire and plug through 10mm hole in fixing surface. Please refer to ADR 13/00 for mounting instructions.
combination Lamp - 100mm x 100mm x 22mm
combination Lamp - 150mm x 80mm x 24mm
• 101BAR • 101BAR2• Stop/Tail • Indicator • Reflector
• 151BAR • 151BAR2• Stop/Tail • Indicator • Reflector
• 101BARLP• Stop/Tail • Indicator • Reflector • Licence
• LP101
• LP151
• 151BARLP• Stop/Tail • Indicator • Reflector • Licence
• 151BAR10• Stop/Tail • Indicator • Reflector
100mm
22mm
100mm
125mm
100mm
80mm
24mm
150mm
100mm
105mm
28mm
150mm
100mm
Product Description: These lamps are fully submersible, rust proof, shock resistant and feature our square lens pattern with 8 high brightness LEDs.
Part no 101BAR 101BAR2 101BAR10 101BARLP2
Voltage: 12 Volt 12 Volt 12 Volt 12 Volt
Cable: 40cm 40cm 10 metre cable 40cm
Packaging: Box Blister of 2 Poly Bag Blister of 2 with licence
Current: @13.8Volts (Stop-0.13Amps) (Tail-0.04Amps) (Ind-0.12Amps) (Licence-0.03 Amps) - @28Volts (Stop-0.12Amps) (Tail-0.06Amps) (Ind-0.07Amps)
C.R.n: This lamp complies with ADR under ECE R1-S1-E9-02, 2a-E9-01, IA-E9-02 (Component number 6444), Licence (L 00 Component number 6110, 6134)
Fitting: Surface mount onto flat surface vertically with Indicator at top using bolts in back of lamp, run wire and plug through 10mm hole in fixing surface. Please refer to ADR 13/00 for mounting instructions.
• 101BAR10• Stop/Tail • Indicator • Reflector
5
YEAR WARRAnTY
ECE approved
5
YEAR WARRAnTY
ECE approved
nEW
PRODUCT
nEW
PRODUCT
15Information Correct at time of printing
Description: These lamps are fully submersible, rust proof, shock resistant and feature our diamond lens pattern. The circuit board is fully encased in resin with corrosion protected tinned copper wiring. Specially designed male & female 4 pin plugs, compatible with the plug in and drive away cable system.
Part no 100BAR 100BARB 100BAR2 100BAR10 100BARLP2 100ARM 100ARM10
Voltage: 12 Volt 12 Volt 12 Volt 12 Volt 12 Volt 12-24 Volt 12-24 Volt
Cable: 40cm with plugs 40cm with plugs 40cm with plugs 10 metre cable 40cm with plugs 40cm with plugs 10 metre cable
Packaging: Box Box Blister of 2 Poly Bag Blister of 2 & licence Blister of 1 Poly Bag
Current: @13.8Volts (Stop-0.13Amps) (Tail-0.04Amps) (Ind-0.12Amps) (Licence-0.03 Amps) - @28Volts (Stop-0.12Amps) (Tail-0.06Amps) (Ind-0.07Amps)
C.R.n: (Stop/tail 37986) (Indicator 37985) (Reflex Reflector 38102) Licence (L 00 Component number 6134)
Fitting: Surface mount onto flat surface vertically with Indicator at top using bolts in back of lamp, run wire and plug through 10mm hole in fixing surface. Please refer to ADR 13/00 for mounting instructions.
Product Description:
These lamps are fully submersible, rust proof, shock resistant and feature our diamond lens pattern. The circuit board is fully encased in resin with corrosion protected tinned copper wiring. Specially designed male & female 4 pin plugs, compatible with the plug in and drive away cable system.
Part no 150BAR 150BARB 150BAR2 150BAR10 150BARLP2 150ARM 150ARM10
Voltage: 12 Volt 12 Volt 12 Volt 12 Volt 12 Volt 12-24 Volt 12-24 Volt
Cable: 40cm with plugs 40cm with plugs 40cm with plugs 10 metre cable 40cm with plugs 40cm with plugs 10 metre cable
Packaging: Box Box Blister of 2 Poly Bag Blister of 2 & licence Blister of 1 Poly Bag
Current: @13.8Volts (Stop-0.13Amps) (Tail-0.04Amps) (Ind-0.12Amps) (Licence-0.03 Amps) - @28Volts (Stop-0.12Amps) (Tail-0.06Amps) (Ind-0.07Amps)
C.R.n: (Stop/tail 37381) (Indicator 37380) (Reflex Reflector 38102) Licence (L 00 Component number 6110)
Fitting: Surface mount onto flat surface vertically with Indicator at top using bolts in back of lamp, run wire and plug through 10mm hole in fixing surface. Please refer to ADR 13/00 for mounting instructions.
combination Lamp - 100mm x 100mm x 22mm
combination Lamp - 150mm x 80mm x 24mm
• 100BAR • 100BAR2 • 100ARM• Stop/Tail • Indicator • Reflector
• 150BAR • 150BAR2 • 150ARM• Stop/Tail • Indicator • Reflector
• 150BARB Black PCB• Stop/Tail • Indicator • Reflector
• 100BARLP• Stop/Tail • Indicator • Reflector • Licence
• LP100• LP100M
• LP150• LP150M
• 100BARB Black PCB• Stop/Tail • Indicator • Reflector
• 100BAR10 • 100ARM10• Stop/Tail • Indicator • Reflector
• 150BARLP• Stop/Tail • Indicator • Reflector • Licence
100mm
22mm
100mm
125mm
100mm
80mm
24mm
150mm
100mm
105mm
28mm
150mm
100mm
• 150BAR10 • 150ARM10• Stop/Tail • Indicator • Reflector
LIFETIME WARRAnTY
ADR / ECE approved
LIFETIME WARRAnTY
ADR / ECE approved
nEW
PRODUCT
nEW
PRODUCT
16 Information Correct at time of printing
Product Description:
These lamps are fully submersible, rust proof, shock resistant and feature our diamond lens pattern. The circuit board is fully encased in resin with corrosion protected tinned copper wiring. Specially designed male & female 4 pin plugs, compatible with the plug in and drive away cable system.
Part no 275BAR 275BARB 275BAR2 275ARM
Voltage: 12 Volt 12 Volt 12 Volt 12-24 Volt
Cable: 40cm with plugs 40cm with plugs 40cm with plugs 40cm with plugs
Packaging: Box Box Blister of 2 Blister of 1
Current: @13.8Volts (Stop-0.14Amps) (Tail-0.07Amps) (Ind-0.10Amps) - @28Volts (Stop-0.11Amps) (Tail-0.05Amps) (Ind-0.12Amps)
C.R.n: (Stop/tail 38658) (Indicator 38657) (Reflex Reflector 38102)
Fitting: Surface mount onto flat surface vertically with Indicator at top using bolts in back of lamp, run wire and plug through 10mm hole in fixing surface. Please refer to ADR 13/00 for mounting instructions.
• 275BAR - 12 volt • 275BAR2 - 12 volt • 275ARM - 12-24 volt• Stop/Tail • Indicator • Reflector
• 275BARB - 12 volt Black PCB• Stop/Tail • Indicator • Reflector
combination Lamp - 275mm x 100mm x 22mm
100mm
22mm
275mm
115mm
LIFETIME WARRAnTY
ADR/ECE approved
Gooseneck to lamp cable• Part No. 5C370
3.7 metre• Part No. 5C430
4.3 metre• Part No. 5C490
4.9 metre• Part No. 5C550
5.5 metre• Part No. 5C610
6.1 metre• Part No. 5C670
6.7 metre• Part No. 5C730
7.3 metre• Part No. 5C800
8.0 metre• Part No. 5C1200
12.0 metre
• Box Trailer Harness Kit
• Boat Trailer Harness Kit
• Part No. BC120012.0 metre
• Part No. BC100010.0 metre
• Part No. BC800
• Part No. BC600
8.0 metre
6.0 metre
Boat trailer cable
Lamp to lamp cable
2.2 metre
3.2 metre
2.1 metre
1.9 metre
• Part No. 4C110
• Part No. 4C130
• Part No. 4C150
• Part No. 4C170
• Part No. 4C190
• Part No. 4C210
• Part No. 4C220
• Part No. 4C320
1.7 metre
1.5 metre
1.3 metre
1.1 metre
1 Metre cable with trailer plug
• Part No. 5C41
• Part No. 5C21
• Part No. 5C81
Boat cable connector• Part No. BCC1
• Available for the 100, 150, 207 and 275 series lamps• Wiring of a trailer can now be done without cutting, splicing, joining or insulating wires & cables• LED Technologies specially designed waterproof plugs and sockets with tinned copper terminals• Tinned copper wire cable – tinning of wire counteracts ‘salt water wicking’ which occurs when moisture is drawn into
the wire & turns it into a greenish gunk caused by chemical reaction• Optional accessory wires at the ends of male plugs if side markers are to be added to the trailer
See page 17 for cables
small Trailer harnessing system
17Information Correct at time of printing
Lamp to Gooseneck cables
Product Description:
(5C) Lamp to gooseneck 5 core cable are fully water proof using anti corrosive tinned copper wire and water proof grease at the plug ends, with ac-cessory wires for licence plate or marker lamps. Up to 9 lengths available.
Length: 3.7 metre 4.3 metre 4.9 metre 5.5 metre 6.1 metre 6.7 metre 7.3 metre 8.0 metre 12.0 metre
Part no: 5C370C Hang 5C430C Hang 5C490C Hang 5C550C Hang 5C610C Hang 5C670C Hang 5C730C Hang 5C800B 5C1200B
Fitting: Plug “T” piece into back of one lamp and then plug the lamp to lamp cable into “T” piece. Run cable to draw bar and plug into Trailer connector.
Product Description:
(4C) Lamp to lamp 4 core cable are fully water proof using anti corrosive tinned copper wire and water proof grease at the plug ends, with accessory wires for licence plate or marker lamps. Up to 8 lengths available.
Length: 1.1 metre 1.3 metre 1.5 metre 1.7 metre 1.9 metre 2.1 metre 3.2 metre
Part no: 4C110C Hang 4C130C Hang 4C150C Hang 4C170C Hang 4C190C Hang 4C210C Hang 4C320B Bulk
Fitting: Plug into back of one lamp and then into “T” piece of the lamp to gooseneck cable.
Lamp to Lamp cables
Electrical harness system suitable for 100,150, 207 and 275 series lamps
1 Metre cable with trailer plug
Product Description:
(5C) Trailer connector 5 core cable are fully water proof using anti corrosive tinned copper wire and water proof grease at the plug ends. 3 sizes available with the most popular plug connectors currently used in Australia, small round, large round and rectangular.
Length: 1 metre 1 metre 1 metre
Part no: 5C41 - Hang 5C81 - Hang 5C21 - Hang
Fitting: Plug into the end of the Lamp to Gooseneck cable, then run along draw bar of trailer and plug trailer connector into vehicle trailer connector base.
Product Description:
(BC) Boat trailer lamp to gooseneck cable are fully water proof using anti corrosive tinned copper wire and water proof grease at the plug ends, with accessory wires for marker lamps with 2C plug ends. 4 lengths available. Y-piece connector to trailer plug cable also available.
Length: 6 metre 8 metre 10 metre 12 metre N/A
Part no: BC600C Hang BC800C Hang BC1000C Hang BC1200C Hang BCC1
Fitting: Use 1 cable per side, plug into back of Left and right lamp then plug into “Y” piece connector at gooseneck. Plug end of Y piece into trailer plug cable.
boat trailer cables andJoiner
Description: The 1 meter of cable with plug clips into back of the 100, 150 and 275 series Generation II lamps. See page 15 or 16 for full details
Part no: LP1 LP1B 35BLM1P
Voltage: Dual Voltage 12-24volt Dual Voltage 12-24volt Dual Voltage 12-24volt
CRn#: 39611 39611 36280
• LP1
• 35BLM1P
Licence plate lamps
7 Pin Flat
7 Pin Round
7 Pin Small Round
BCC1
18 Information Correct at time of printing
Product Description:
Our own product proudly designed and made in Australia from high quality components, we consider this light to be the best in the Australian market. Our reputation is on the line.
Part no 275GARWM - Grey Frame 275RARWM - Red Frame
Voltage: 12-24 Volt 12-24 Volt
Cable: 40cm 40cm
Packaging: Blister Blister
Current: TBA
C.R.n: (Stop/tail 43223) (Indicator 43221) (Reverse 43222) (Reflex Reflector 38102)
Fitting: Surface mount onto flat surface horizontally to the ground using bolts in back of lamp, run wire and plug through 10mm hole in fixing surface. Please refer to ADR 13/00 for mounting instructions.
combination Lamp - 275mm x 100mm x 33mm
MADE in AusTrALiA
• 275GARWM• Stop/Tail • Indicator • Reverse • Reflector
• 275RARWM• Stop/Tail • Indicator • Reverse • Reflector
100mm
33mm
275mm
100mm
5
YEAR WARRAnTY
ADR approved
nEW
PRODUCT
nEW
PRODUCT
80mm
24mm
250mm
200mm
combination Lamp - 250mm x 80mm x 24mm
• 250ARWM • 250ARWMB• Stop/Tail • Indicator • Reverse • Reflector
• 250RARM • 250RARMB• Stop/Tail • Indicator • Reflector
Product Description:
These lamps are fully submersible, rust proof, shock resistant and feature our diamond lens pattern. The circuit board is fully encased in resin with corrosion protected tinned copper wiring. Same lens design as our popular 150 series.
Part no 250ARWM 250ARWMB 250RARM 250RARMB
Voltage: 12-24 Volt 12-24 Volt 12-24 Volt 12-24 Volt
Cable: 40cm 40cm 40cm 40cm
Packaging: Blister Bulk Blister Bulk
Current: TBA
C.R.n: This lamp complies with ADR with ECE approval (Stop/tail 43362) (Indicator 43361) (Reflex Reflector 38102)
Fitting: Surface mount onto flat surface horizontally to ground using bolts in back of lamp, run wire and plug through 10mm hole in fixing surface. Please refer to ADR 13/00 for mounting instructions.
5
YEAR WARRAnTY
ADR/ECE approved
nEW
PRODUCT
nEW
PRODUCT
19Information Correct at time of printing
• J3RM• Stop/Tail • Reflector
• J3AM• Indicator • Reflector
• J3WM• Reverse • Reflector
Product Description:
The J3 series Jumbo lamps are water proof and shock resistant, with classic styling, modern aesthetic appeal and featuring a specially designed inner chrome reflector. Individual lenses are available separately for replacement. These lamps are ADR approved for horizontal or vertical mount.
replacement inserts - 194mm x 123mm x 30mm
194mm
30mm
123mm
• J3BARRM• Stop/Tail • Indicator• Reflector
• J3BARM• Stop/Tail • Indicator• Reflector
• J3BARWM• Stop/Tail • Indicator • Reverse• Reflector
Product Description:
The J3 series Jumbo lamps are water proof and shock resistant, with classic styling, modern aesthetic appeal and featuring a specially designed inner chrome reflector. Individual lenses are available separately for replacement. These lamps are ADR approved for horizontal or vertical mount. Soon to be released in triple red configuration.
Part no J3BARRM J3BRRRM J3BARWM
Voltage: 12-24 Volt 12-24 Volt 12-24 Volt
Cable: 1.2 metre sheathed hard wired 1.2 metre sheathed hard wired 1.2 metre sheathed hard wired
Packaging: Blister carry pack of 1 Blister carry pack of 1 Blister carry pack of 1
Current: @13.8Volts 1.80Amps - @28Volts 0.78Amps @13.8Volts TBAAmps - @28Volts TBAAmps @13.8Volts 1.00Amps - @28Volts 0.48Amps
C.R.n: (Stop/tail 42965) (Indicator 42964) (Reverse 42967) (Reflector 42966)
Fitting: Surface mount onto flat surface horizontally or vertically using bolts in back of lamp, run wires through hole in fixing surface. Please refer to ADR 13/00 for mounting instructions.
Product Description:
The J3 series Jumbo lamps are water proof and shock resistant, with classic styling, modern aesthetic appeal and featuring a specially designed inner chrome reflector. Individual lenses are available separately for replacement. These lamps are ADR approved for horizontal or vertical mount.
Part no J3BARM
Voltage: 12-24 Volt
Cable: 1.2 metre sheathed hard wired
Packaging: Blister carry pack of 1
Current: @13.8Volts 1.80Amps - @28Volts 0.78Amps
C.R.n: (Stop/tail 42965) (Indicator 42964) (Reflector 42966)
Fitting: Surface mount onto flat surface horizontally or vertically using bolts in back of lamp, run wires through hole in fixing surface. Please refer to ADR 13/00 for mounting instructions.
combination Lamp - 400mm x 130mm x 45mm
Jumbo combination Lamp - 595mm x 130mm x 45mm
595mm
45mm
500mm
130mm
400mm
45mm
130mm
5
YEAR WARRAnTY
ADR approved
ADR approved
ADR approved
WARRAnTY
WARRAnTY
5
YEAR
5
YEAR
nEW
PRODUCT
nEW
PRODUCT
nEW
PRODUCT nEW
PRODUCT nEW
PRODUCT
nEW
PRODUCT
20 Information Correct at time of printing
• 80BSTIM• 80BSTIMB• Stop/Tail • Indicator
• 100BSTIM• 100BSTIMB• Stop/Tail • Indicator
• 125BSTIM• 125BSTIMB• Stop/Tail • Indicator
• 100CSTIM• Stop/Tail • Indicator
• 125CSTIM• Stop/Tail • Indicator
Product Description:
The 80 series lamps are fully submersible, shock resistant and feature our hexagonal lens pattern. Specifically designed for trailers or small sized commercial vehicles. Individual clip in lenses allow easy surface mount with no visible screws.
Part no 80BSTIM 80BSTIMB 80CSTIM
Voltage: 12-24 Volt 12-24 Volt 12-24 Volt
Cable: 40cm 40cm 40cm
Packaging: Blister of 1 Box of 1 Blister of 1
Current: @13.8Volts (Stop-0.33Amps) (Tail-0.06Amps) (Ind-0.31Amps) (Rev-0.29Amps) - @28Volts (Stop-0.25Amps) (Tail-0.04Amps) (Ind-0.22Amps) (Rev-0.21Amps) Each lens @13.8Volts (Stop-0.27Amps) (Tail-0.04Amps) (Ind-0.18Amps) - @28Volts (Stop-0.13Amps) (Tail-0.04Amps) (Ind-0.09Amps) Stop/Tail/Ind single lens
C.R.n: Combination lamp (Stop 35788) (tail 35789) (Indicator 35787)
Fitting: Surface mount bracket, run wires through back and clip lens into place. Please refer to ADR 13/00 for mounting instructions.
combination Lamp - 100mm x 100mm x 28mm
Product Description:
The 100 series lamps are fully submersible, shock resistant and feature our hexagonal lens pattern. Specifically designed for trailers or small sized commercial vehicles. Individual clip in lenses allow easy surface mount with no visible screws.
Part no 100BSTIM 100CSTIM
Voltage: 12-24 Volt 12-24 Volt
Cable: 40cm Hard wired 40cm Hard wired
Packaging: Blister of 1 Blister of 1
Current: @13.8Volts (Stop-0.17Amps) (Tail-0.04Amps) (Ind-0.18Amps) - @28Volts (Stop-0.14Amps) (Tail-0.04Amps) (Ind-0.11Amps)
C.R.n: (Stop 35781) (tail 35782) (Indicator 35783)
Fitting: Surface mount to flat surface using bolts in back of lamp, run wire through hole in fixing surface. Please refer to ADR 13/00 for mounting instructions.
Product Description:
The 125 series lamps are fully submersible, shock resistant and feature our hexagonal lens pattern. Specifically designed for trailers or small sized commercial vehicles. Individual clip in lenses allow easy surface mount with no visible screws.
Part no 125BSTIM 125BSTIMB 125CSTIM
Voltage: 12-24 Volt 12-24 Volt 12-24 Volt
Cable: 40cm Hard wired 40cm Hard wired 40cm Hard wired
Packaging: Blister of 1 Box of 1 Blister of 1
Current: @13.8Volts (Stop-TBAAmps) (Tail-TBAAmps) (Ind-TBAAmps) - @28Volts (Stop-TBAAmps) (Tail-TBAAmps) (Ind-TBAAmps)
C.R.n: (Stop TBA) (tail TBA) (Indicator TBA)
Fitting: Surface mount to flat surface using bolts in back of lamp, run wire through hole in fixing surface. Please refer to ADR 13/00 for mounting instructions.
combination Lamp - 122mm x 122mm x 31mm
combination Lamp - 147mm x 147mm x 31mm
• 80CSTIM• Stop/Tail • Indicator 100mm
28mm
100mm
122mm
31mm
122mm
ADR/ECE approved
ADR/ECE approved
ADR/ECE approved
100mm
28mm
100mm
122mm
31mm
122mm
147mm 31mm
147mm
WARRAnTY
5
YEAR
WARRAnTY
5
YEAR
WARRAnTY
5
YEAR
147mm
31mm
147mm
21Information Correct at time of printing
Product Description:
The 80 series lamps are fully submersible, rust proof and shock resistant and feature our hexagonal pattern lens. The rear of the circuit board is fully encased in resin. Individual clip in lenses for easy replacement.
Part no 80BAR 80CAR 80BARM 80CARM
Voltage: 12 Volt 12 Volt 12-24 Volt 12-24 Volt
Cable: 40cm Hardwired 40cm Hardwired 40cm Hardwired 40cm Hardwired
Packaging: Blister of 1 Blister of 1 Blister of 1 Blister of 1
Current: @13.8Volts (Stop-0.33Amps) (Tail-0.06Amps) (Ind-0.31Amps) - @28Volts (Stop-0.25Amps) (Tail-0.04Amps) (Ind-0.22Amps)
C.R.n: (Stop/tail 33059) (Indicator 33098)
Fitting: Surface mount bracket onto flat surface horizontally to the ground with screws provided, run wires through back and clip lens into place. Please refer to ADR 13/00 for mounting instructions.
• 80BAR • 80BARM• Stop/Tail • Indicator
• 125BARML- Left Side• Stop/Tail • Indicator• Reflector
• 125BARMR - Right Side• Stop/Tail • Indicator• Reflector
• 80CAR• 80CARM• Stop/Tail • Indicator
combination Lamp - 188mm x 100mm x 28mm
combination Lamp - 340mm x 200mm x 60mm
Product Description:
The 125 series lamps are fully submersible, shock resistant, feature our hexagonal lens pattern. Specifically designed for retro fit to same type commercial vehicles. This assembly has individual clip in lenses for easy replacement.
Part no 125BARML 125BARMR
Voltage: 12-24 Volt 12-24 Volt
Cable: 16cm loomed and sheathed from outer casing. 16cm loomed and sheathed from outer casing.
Packaging: Box Box
Current: @13.8Volts (Stop-0.42Amps) (Tail-0.04Amps) (Ind-0.43Amps) - @28Volts (Stop-0.26Amps) (Tail-0.06Amps) (Ind-0.26Amps)
C.R.n: (Stop/tail 33403) (Indicator 33165) (Reflex Reflector 38102)
Fitting: Secure horizontally to the ground using top or back mounting holes in assembly and run wires through back. Refer to ADR 13/00 for mounting instructions.
200mm
60mm
340mm
188mm
28mm
100mm
150mm
5
YEAR WARRAnTY
ADR/ECE approved
5
YEAR WARRAnTY
ADR/ECE approved
22 Information Correct at time of printing
Product Description:
The 80 series lamps are fully submersible, shock resistant and feature our hexagonal lens pattern. The rear of the circuit board is fully encased in resin. Individual clip in lenses for easy replacement, surface mount with no visible screws. Specifically designed for trailers or small sized commercial vehicles.
Part no 80BARR 80BARW 80BARRM 80BARWM 80CARR 80CARW 80CARRM 80CARWM
Voltage: 12 Volt 12 Volt 12-24 Volt 12-24 Volt 12 Volt 12 Volt 12-24 Volt 12-24 Volt
Cable: 40cm 40cm 40cm 40cm 40cm 40cm 40cm 40cm
Packaging: Blister of 1 Blister of 1 Blister of 1 Blister of 1 Blister of 1 Blister of 1 Blister of 1 Blister of 1
Current: @13.8Volts (Stop-0.33Amps) (Tail-0.06Amps) (Ind-0.29Amps) (Rev-0.17Amps) - @28Volts (Stop-0.25Amps) (Tail-0.04Amps) (Ind-0.22Amps) (Rev-0.21Amps) Each lens
C.R.n: (Stop/tail 33059) (Indicator 33098) (Reverse 35797)
Fitting: Surface mount bracket onto flat surface horizontally to the ground with screws provided, run wires through back and clip lens into place. Please refer to ADR 13/00 for mounting instructions.
Product Description:
The 80 series lamps are fully submersible, shock resistant and feature our hexagonal lens pattern. The rear of the circuit board is fully encased in resin. Individual clip in lenses for easy replacement. Surface mounted onto supplied metal right angled bracket available in black or silver with no visible screws. Specifically designed for trailers or small sized commercial vehicles.
Part no 80CARRSKT 80CARWSKT 80BARRSKT 80BARWSKT
Voltage: 12 Volt 12 Volt 12 Volt 12 Volt
Cable: 40cm 40cm 40cm 40cm
Packaging: Blister of 2 Blister of 2 Blister of 2 Blister of 2
Current: @13.8Volts (Stop-0.33Amps) (Tail-0.06Amps) (Ind-0.29Amps) (Rev-0.17Amps) - @28Volts (Stop-0.25Amps) (Tail-0.04Amps) (Ind-0.22Amps) (Rev-0.21Amps) Each lens
C.R.n: (Stop/tail 33059) (Indicator 33098) (Reverse 35797)
Fitting: Surface mount bracket onto flat surface horizontally to the ground with screws provided, run wires through back and clip lens into place. Please refer to ADR 13/00 for mounting instructions.
• 80BARWSKT - 12 volt• Stop/Tail/Indicator/Reverse including right angle bracket
• 80BARRSKT - 12 volt• Stop/Tail/Indicator including right angle bracket
• 80BARR - 12 volt • 80BARRM - multivolt• Stop/Tail/Indicator
• 80BARW - 12 volt • 80BARWM - multivolt• Stop/Tail/Indicator/Reverse
combination Lamp - 278mm x 100mm x 28mm
combination Lamp - 280mm x 110mm x 29mm
278mm
28mm
100mm
240mm
• 80CARR - 12 volt • 80CARRM - multivolt• Stop/Tail/Indicator
• 80CARW - 12 volt • 80CARWM - multivolt• Stop/Tail/Indicator/Reverse
• 80CARWSKT - 12 volt• Stop/Tail/Indicator/Reverse including right angle bracket
• 80CARRSKT - 12 volt• Stop/Tail/Indicator including right angle bracket
280mm
110mm
53mm
29mm
120mm 120mm
5
YEAR WARRAnTY
ADR/ECE approved
5
YEAR WARRAnTY
ADR/ECE approved
nEW
PRODUCT
nEW
PRODUCT
nEW
PRODUCT
nEW
PRODUCT
23Information Correct at time of printing
Product Description:
The 100 series lamps are fully submersible, shock resistant and feature our hexagonal lens pattern. Specifically designed for trailers or medium sized commercial vehicles. Individual clip in lenses allow easy replacement and surface mounted with no visible screws.
Part no 100BARRM 100CARRM 100BARWM 100CARWM
Voltage: 12-24 Volt 12-24 Volt 12-24 Volt 12-24 Volt
Cable: 40cm Hard wired 40cm Hard wired 40cm Hard wired 40cm Hard wired
Packaging: Blister of 1 Blister of 1 Blister of 1 Blister of 1
Current: @13.8Volts (Stop-0.38Amps) (Tail-0.04Amps) (Ind-0.38Amps) (Rev-0.31Amps) - @28Volts (Stop-0.24Amps) (Tail-0.07Amps) (Ind-0.23Amps) (Rev-0.17Amps) Each lens
C.R.n: (Stop/tail 33402) (Indicator 33156) (Reverse 35793)
Fitting: Surface mount bracket onto flat surface horizontally to the ground with screws provided, run wires through back and clip lens into place. Please refer to ADR 13/00 for mounting instructions.
• 100BARRM• Stop/Tail • Indicator
• 100CARRM• Stop/Tail • Indicator
• 100BARWM• Stop/Tail • Indicator • Reverse
• 100CARWM• Stop/Tail • Indicator • Reverse
combination Lamp - 350mm x 120mm x 31mm
350mm
31mm
120mm
290mm
Product Description:
The 125 series lamps are fully submersible, shock resistant and feature our hexagonal lens pattern specifically designed for trailers or medium sized commercial vehicles. Individual clip in lenses allow easy surface mount with no visible screws.
Part no 125BARRM 125CARRM 125BARWM 125CARWM
Voltage: 12-24 Volt 12-24 Volt 12-24 Volt 12-24 Volt
Cable: 40cm Hard wired 40cm Hard wired 40cm Hard wired 40cm Hard wired
Packaging: Blister of 1 Blister of 1 Blister of 1 Blister of 1
Current: @13.8Volts (Stop-0.42Amps) (Tail-0.04Amps) (Ind-0.43Amps) (Rev-0.36Amps) - @28Volts (Stop-0.26Amps) (Tail-0.06Amps) (Ind-0.25Amps) (Rev-0.18Amps) Each lens
C.R.n: (Stop/tail 33403) (Indicator 33165) (Reverse 35794)
Fitting: Surface mount bracket onto flat surface horizontally to the ground with screws provided, run wires through back and clip lens into place. Please refer to ADR 13/00 for mounting instructions.
• 125BARRM• Stop/Tail • Indicator
• 125CARRM• Stop/Tail • Indicator
• 125BARWM• Stop/Tail • Indicator • Reverse
• 125CARWM• Stop/Tail • Indicator • Reverse
combination Lamp - 435mm x 145mm x 31mm
435mm
31mm
147mm
370mm
5
YEAR WARRAnTY
ADR/ECE approved
5
YEAR WARRAnTY
ADR/ECE approved
24 Information Correct at time of printing
• 100BAARRM• Stop/Tail • Indicator
• 100BARRWM• Stop/Tail • Indicator • Reverse
combination Lamp - 430mm x 125mm x 50mm
Product Description:
The 100 series lamps are fully submersible, shock resistant and feature our hexagonal lens pattern. Specifically designed for trailers or medium sized commercial vehicles. This assembly is set up with individual clip in lenses. Brackets available separately.
Part no 100BAARRM 100BARRWM
Voltage: 12-24 Volt 12-24 Volt
Cable: 40cm Hard wired 40cm Hard wired
Packaging: Blister of 1 Blister of 1
Current: @13.8Volts (Stop-0.38Amps) (Tail-0.04Amps) (Ind-0.38Amps) (Rev-0.29Amps) - @28Volts (Stop-0.24Amps) (Tail-0.07Amps) (Ind-1.23Amps) (Rev-0.17Amps). Each lens.
C.R.n: (Stop/tail 33402) (Indicator 33156) (Reverse 35793)
Fitting: Surface mount assembly onto flat surface horizontally to the ground with bolts provided, run wires through back and clip lens into place. Please refer to ADR 13/00 for mounting instructions.
50mm
430mm
125mm
152.6mm
Product Description:
The 80 series lamps are fully submersible, shock resistant and feature our hexagonal lens pattern. Specifically designed for trailers or small sized commercial vehicles. This assembly is loomed up with individual clip in lenses. Brackets available separately.
Part no 80BAARRM 80BARRWM
Voltage: 12-24 Volt 12-24 Volt
Cable: 40cm Hardwired 40cm Hardwired
Packaging: Blister of 1 Blister of 1
Current: @13.8Volts (Stop-0.38Amps) (Tail-0.04Amps) (Ind-0.38Amps) (Rev-0.31Amps) - @28Volts (Stop-0.25Amps) (Tail-0.04Amps) (Ind-0.22Amps) (Rev-0.21Amps) Each lens.
C.R.n: (Stop/tail 33059) (Indicator 33098) (Reverse 35797)
Fitting: Surface mount assembly onto flat surface horizontally to the ground with bolts provided, run wires through back. Please refer to ADR 13/00 for mounting instructions.
• 80BAARRM• Stop/Tail • Indicator
• 80BARRWM• Stop/Tail • Indicator• Reverse
combination Lamp - 350mm x 105mm x 48mm
48mm
350mm
105mm
256mm
5
YEAR WARRAnTY
ADR/ECE approved
5
YEAR WARRAnTY
ADR/ECE approved
25Information Correct at time of printing
Product Description:
The 200 series are fully submersible, rust proof, shock resistant and feature our hexagonal pattern lens. The rear of the circuit board is fully encased in resin. Their size is designed to fit into small spaces with individual clip in lenses for easy replacement and surface mounted with no visible screws.
Part no 200BSTIM 200BSTIMB 200CSTIM 200BSTIRMB 200BSTIR48
Voltage: 12-24 Volt 12-24 Volt 12-24 Volt 12-24 Volt 48 Volt
Cable: 40cm Hard wired 40cm Hard wired 40cm Hard wired 40cm Hard wired 40cm Hard wired
Packaging: Blister of 1 Box of 1 Blister of 1 Box of 1 Box of 1
Current:BSTIM - @13.8Volts (Stop-0.29Amps) (Tail-0.09Amps) (Ind-0.19Amps) - @28Volts (Stop-0.16Amps) (Tail-0.07Amps) (Ind-0.07Amps) BSTIRM - @13.8Volts (Stop-0.10Amps) (Tail-0.02Amps) (Ind-0.11Amps) (Rev-0.10Amps) - @28Volts (Stop-0.08Amps) (Tail-0.04Amps) (Ind-0.08Amps) (Rev-0.08Amps) @48Volts (Stop-0.41Amps) (Tail-0.11Amps) (Ind-0.40Amps) (Rev-0.28Amps)
C.R.n: (Stop/tail 35786, 35785) (Indicator 35784) NO NO
Fitting: Surface mount bracket with screws provided, run wires through back and clip lens into place. Please refer to ADR 13/00 for mounting instructions.
• 200BSTIM• 200BSTIMB• Stop/Tail • Indicator
• 200CSTIM• Stop/Tail • Indicator
• 200BSTIR48• 200BSTIRM• Stop/Tail • Indicator • Reverse• Non ADR/ECE Approved
combination Lamp - 200mm x 50mm x 28mm
28mm
200mm
50mm
Product Description:
The 200 series are fully submersible, rust proof and shock resistant and feature our hexagonal pattern lens. The rear of the circuit board is fully encased in resin. Their size is designed to fit into small spaces with individual clip in lenses for easy replacement and surface mounted with no visible screws.
Part no 200BARM 200CARM 200BRWM 200CRWM
Voltage: 12-24 Volt 12-24 Volt 12-24 Volt 12-24 Volt
Cable: 40cm 40cm 40cm 40cm
Packaging: Blister of 1 Blister of 1 Blister of 1 Blister of 1
Current: @13.8Volts (Stop-0.32Amps) (Tail-0.04Amps) (Ind-0.34Amps) (Rev-0.17Amps) - @28Volts (Stop-0.18Amps) (Tail-0.04Amps) (Ind-0.19Amps) (Rev-0.18Amps) Each lens
C.R.n: (Stop/tail 35941) (Indicator 35795) (Reverse 35796)
Fitting: Surface mount bracket onto flat surface horizontally to the ground with bolts provided, run wires through back and clip lens into place. Please refer to ADR 13/00.
• 200BARM• Stop/Tail • Indicator
• 200CARM• Stop/Tail • Indicator
• 200BRWM• Stop/Tail • Indicator • Reverse
• 200CRWM• Stop/Tail • Indicator • Reverse
combination Lamp - 200mm x 92mm x 28mm
28mm
200mm
92mm
ADR/ECE approved
ADR/ECE approved
Product Description:
The 200/207 series boat trailer lamps are fully submersible, shock resistant and utilize our plug in and drive away cable system or can be wired to existing looms with 40cm of tinned copper wire in a dual protective cable. Replaceable lenses, surface mount with no visible screws.
Part no 207BARP 207BARL 207BARLP2 200BARLPM2
Voltage: 12 Volt 12 Volt 12 Volt 12-24 Volt
Cable: 40cm with plugs 40cm with plugs 40cm with plugs 40cm with plugs
Packaging: Poly Bag of 1 Poly Bag of 1 Blister of 2 LHS/RHS Blister of 2 LHS/RHS
Current: @13.8Volts (Stop-0.18Amps) (Tail-0.07Amps) (Ind-0.17Amps) (Lic-0.02Amps) - @28Volts (Stop-0.32Amps) (Tail-0.04Amps) (Ind-0.39Amps) (Lic-0.02Amps)
C.R.n: 12 Volt - (Stop/tail 37371) (Indicator 37350) (Licence37845) 12-24 Volt - (Stop/tail 35941) (Indicator 35795) (Licence 37844)
Fitting: Surface mount onto flat surface horizontally to the ground with stainless steel bolts provided in assembly and run cable through 12mm hole. Please refer to ADR 13/00.
• 207BARP• Stop/Tail • Indicator
• 200BARP• Stop/Tail • Indicator
• 207BARL• Stop/Tail • Indicator• Licence
• 200BARL• Stop/Tail • Indicator• Licence
combination Lamp - 200mm x 92mm x 28mm Trailer harness Available page 17
28mm
200mm
92mm
28mm
200mm
113mm
ADR/ECE approved
WARRAnTY
WARRAnTY
WARRAnTY
5
YEAR
5
YEAR
5
YEAR
26 Information Correct at time of printing
Product Description:
The 200 series are fully submersible, rust proof and shock resistant and feature a hexagonal pattern lens. The rear of the circuit board is fully encased in resin. Their size is designed to fit into small spaces with individual clip in lenses for easy replacement and surface mounted with no visible screws.
Part no 200BARRM 200CARRM 200BARWM 200CARWM
Voltage: 12-24 Volt 12-24 Volt 12-24 Volt 12-24 Volt
Cable: 40cm 40cm 40cm 40cm
Packaging: Blister of 1 Blister of 1 Blister of 1 Blister of 1
Current: @13.8V (Stop-0.32Amps) (Tail-0.04Amps) (Ind-0.34Amps) (Rev-0.17Amps) - @28V (Stop-0.18Amps) (Tail-0.04Amps) (Ind-0.19Amps) (Rev-0.18Amps) Each lens
C.R.n: (Stop/tail 35941) (Indicator 35795) (Reverse 35796)
Fitting: Surface mount bracket onto flat surface horizontally to the ground with bolts provided, run wires through back and clip lens into place. Please refer to ADR 13/00.
• 200CARRM• Stop/Tail • Indicator
• 200CARWM• Stop/Tail • Indicator • Reverse
• 200BARRM• Stop/Tail • Indicator
• 200BARWM• Stop/Tail • Indicator • Reverse
combination Lamp - 200mm x 134mm x 28mm
28mm
200mm
134mm
ADR/ECE approved
WARRAnTY
5
YEAR
combination Lamp - 400mm x 135mm x 40mm
Product Description:
A unique idea giving more choice and versatility for truck and trailer applications. 6 bank combination housing either 200 or 207 series lamps, individual clip in lenses. Backing plate also available separately.
Part no 207BAR6 200BARM6
Voltage: 12 Volt 12-24 Volt
Cable: 40cm Hard wired 40cm Hard wired
Packaging: Box of 1 Box of 1
Current: @13.8Volts (Stop-0.54Amps) (Tail-0.21Amps) (Ind-0.51Amps) - @28Volts (Stop-0.96Amps) (Tail-0.12Amps) (Ind-1.17Amps).
C.R.n: 12 Volt - (Stop/tail 37371) (Indicator 37350) 12-24 Volt - (Stop/tail 35941) (Indicator 35795)
Fitting: Surface mount onto flat surface horizontally to the ground with stainless steel bolts provided in assembly and run cable. Please refer to ADR 13/00.
• 207BAR6• Stop/Tail • Indicator
• 200BARM6• Stop/Tail • Indicator
400mm
280mm
135mm
40mm
400mm
280mm
135mm
40mm
ADR/ECE approved
Product Description:
A unique idea giving more choice and versatility for truck and trailer applications. 4 bank combination housing either 200 or 207 series lamps also available with a licence plate lamp, individual clip in lenses. Backing plate also available separately.
Part no 207BAR4 207BARL4 200BARM4 200BARLM4
Voltage: 12 Volt 12 Volt 12-24 Volt 12-24 Volt
Cable: 40cm Hard wired 40cm Hard wired 40cm Hard wired 40cm Hard wired
Packaging: Box of 1 Box of 1 Blister of 1 Blister of 1
Current: @13.8V (Stop-0.36Amps) (Tail-0.14Amps) (Ind-0.34Amps) (Lic-0.02Amps) - @28V (Stop-0.64Amps) (Tail-0.08Amps) (Ind-0.78Amps) (Lic-0.02Amps)
C.R.n: 12 Volt - (Stop/tail 37371) (Indicator 37350) (Licence37845) 12-24 Volt - (Stop/tail 35941) (Indicator 35795) (Licence 37844)
Fitting: Surface mount onto flat surface horizontally to the ground with stainless steel bolts provided in assembly, run cable through 12mm hole. Please refer to ADR 13/00.
combination Lamp - 400mm x 92mm x 40mm
400mm
400mm
113mm
40mm
40mm
92mm
280mm
280mm• 207BAR4• Stop/Tail • Indicator
• 200BARM4• Stop/Tail • Indicator
• 207BARL4• Stop/Tail • Indicator • Licence
• 200BARLM4• Stop/Tail • Indicator • Licence
5
YEAR WARRAnTY
ADR/ECE approved
WARRAnTY
5
YEAR
27Information Correct at time of printing
• J9BARRM• Stop/Tail • Indicator
• J9BARWM• Stop/Tail • Indicator • Reverse
Product Description:
The 200 series Jumbo lamps are fully submersible, shock resistant and feature our hexagonal lens pattern. They are the same dimensions as the common three lamp jumbo. Individual clip in lenses for easy replacement, or use the J9 bracket to make your own combination.
Part no J9BARRM J9BARWM
Voltage: 12-24 Volt 12-24 Volt
Cable: 40cm Hard wired, loomed. 40cm Hard wired, loomed.
Packaging: Blister of 1 Blister of 1
Current: @13.8Volts (Stop-0.32Amps) (Tail-0.04Amps) (Ind-0.34Amps) (Rev-0.17Amps) - @28Volts (Stop-0.18Amps) (Tail-0.04Amps) (Ind-0.19Amps) (Rev-0.18Amps) Each lens
C.R.n: (Stop/tail 35941) (Indicator 35795) (Reverse 35796)
Fitting: Surface mount onto flat surface horizontally to the ground with bolts provided in assembly, run loomed cable through 12mm hole. Please refer to ADR 13/00 for mounting instructions.
Product Description:
The 200 series Jumbo lamps are fully submersible, shock resistant and feature our hexagonal lens pattern. They are the same dimensions as the common three lamp jumbo. Individual clip in lenses for easy replacement, or use the J9 bracket to make your own combination.
Part no J9CARRM J9CARWM
Voltage: 12-24 Volt 12-24 Volt
Cable: 40cm Hard wired, loomed. 40cm Hard wired, loomed.
Packaging: Blister of 1 Blister of 1
Current: @13.8Volts (Stop-0.32Amps) (Tail-0.04Amps) (Ind-0.34Amps) (Rev-0.17Amps) - @28Volts (Stop-0.18Amps) (Tail-0.04Amps) (Ind-0.19Amps) (Rev-0.18Amps) Each lens
C.R.n: (Stop/tail 35941) (Indicator 35795) (Reverse 35796)
Fitting: Surface mount onto flat surface horizontally to the ground with bolts provided in assembly, run loomed cable through 12mm hole. Please refer to ADR 13/00 for mounting instructions.
• J9CARRM• Stop/Tail • Indicator
• J9CARWM• Stop/Tail • Indicator • Reverse
combination Lamp - 594mm x 130mm x 28mm
combination Lamp - 594mm x 130mm x 28mm
130mm 28mm
594mm
130mm 28mm
594mm
130mm 28mm
594mm
130mm 28mm
594mm
5
YEAR WARRAnTY
ADR/ECE approved
5
YEAR WARRAnTY
ADR/ECE approved
28 Information Correct at time of printing
Product Description:
The 135 series lamps are fully submersible, shock resistant, feature our diamond lens pattern and are excellent for small tight spaces. Individual push in bracket or grommet mounted lenses for surface or recess mount with no visible screws. ADR compliant for horizontal use.
Part no 135ARM 135ARMG
Voltage: 12-24 Volt 12-24 Volt
Cable: 40cm Hard wired. 40cm Hard wired.
Packaging: Blister of 1 Blister of 1
Current: @13.8Volts (Stop-0.12Amps) (Tail-0.01Amps) (Ind-0.21Amps) - @28Volts (Stop-0.08Amps) (Tail-0.02Amps) (Ind-0.11Amps)
C.R.n: (Stop/tail 39847) (Indicator 39846)
Fitting: Surface mount horizontally to the ground with screws or plugs provided, run wires through back & clip lens into place. Please refer to ADR 13/00 for mounting instructions.
combination Lamp - 135mm x 38mm x 24mm
• 135ARM• Stop/Tail • Indicator
Recessed grommet type
Flush mounted type
• 135ARMG• Stop/Tail • Indicator
135mm
145mm
133mm
38mm
48mm
36mm
24mm
21mm
80mm
135mm
145mm
133mm
38mm
48mm
36mm
24mm
21mm
80mm
135mm
145mm
133mm
38mm
48mm
36mm
24mm
21mm
80mm
135mm
145mm
133mm
38mm
48mm
36mm
24mm
21mm
80mm
135mm
133mm
38mm
36mm
24mm
21mm
80mm
135mm
145mm
133mm
38mm
48mm
36mm
24mm
21mm
80mm
Cut out size
ADR/ECE approved
WARRAnTY
5
YEAR
• 235BAR12• Stop/Tail • Indicator
• 235CAR12• Stop/Tail • Indicator
• 235WAR12• Stop/Tail • Indicator
combination strip Lamps - 258mm x 82mm x 17mm
Product Description:
The 235 series lamps have been released and blister packed with a twin chrome bracket that allows them to be surface mounted without the need for a cut out. The brackets are also available separately in chrome, white and black.
Part no 235BAR12 235CAR12 235WAR12
Voltage: 12 Volt only 12 Volt only 12 Volt only
Cable: 40cm 40cm 40cm
Packaging: Blister of 1 Blister of 1 Blister of 1
Current: @13.8Volts (Stop-0.14 Amps) (Tail-0.04 Amps) (Ind-0.16 Amps)
C.R.n (Stop/tail 37678) (Indicator 39092)
Fitting: Surface mount bracket and lights horizontally to ground with screws provided, please refer to ADR 13/00 for mounting instructions.
258mm
82mm
17mm
258mm
82mm
17mm
ADR/ECE approvednEW
PRODUCT
WARRAnTY
5
YEAR
• 380BAR12• Stop/Tail • Indicator
Product Description:
The 380 series lamps have been released and blister packed with a twin chrome bracket that allows them to be surface mounted without the need for a cut out. The brackets are also available separately in chrome, white and black.
Part no 380BAR12 380CAR12
Voltage: 12 Volt only 12 Volt only
Cable: 40cm 40cm
Packaging: Blister of 1 Blister of 1
Current: @13.8Volts (Stop-0.16 Amps) (Tail-0.04 Amps) (Ind-0.18 Amps)
C.R.n (Stop/tail 39473) (Indicator 39470)
Fitting: Surface mount bracket and lights horizontally to ground with screws provided, please refer to ADR 13/00 for mounting instructions.
428mm
97mm
22mm
428mm
97mm
22mm
nEW
PRODUCT
WARRAnTY
5
YEAR • 380CAR12
• Stop/Tail • Indicator
combination strip Lamps - 428mm x 97mm x 22mmADR/ECE approved
29Information Correct at time of printing
combination Lamp - 470mm x 70mm x 40mm ADR/ECE approved
Product Description:
The 135 series lamps are fully submersible, shock resistant and feature our diamond lens pattern, excellent for small tight spaces. Mounted into chrome plated triple “L” bracket, two combinations available.
Part no 135CARRM 135CARWMR 135CARWML
Voltage: 12-24 Volt 12-24 Volt 12-24 Volt
Cable: 40cm Hard wired 40cm Hard wired 40cm Hard wired
Packaging: Box of 1 Box of 1 Right hand side Box of 1 Left hand side
Current: @13.8Volts (Stop-0.11Amps) (Tail-0.02Amps) (Ind-0.16Amps) (Rev-0.23Amps) - @28Volts (Stop-0.08Amps) (Tail-0.02Amps) (Ind-0.06Amps) (Rev-0.19Amps).
C.R.n: (Stop/tail 39848) (Indicator 39845) (Reverse 39849)
Fitting: Fix L bracket horizontally to the ground with lamps using three fixing points at top of bracket, hard wired. Refer to ADR 13/00 for mounting instructions.
• 135CARRM• Stop/Tail • Indicator
• 140STIM• Stop/Tail • Indicator
• 140STILM• Stop/Tail • Indicator• Licence
• 135CARWMR• Stop/Tail • Indicator • Reverse
combination Lamp - 140mm round x 66mm depth
470mm
70mm
40mm
140mm
66mm
5
YEAR WARRAnTY
ECE approved
Product Description:
The New LUMILAMPS are fully submersible, shock resistant and features a new stylish design. All five functions are standard with this lamp. Left and Right side available.
Part no LUMILAMP2 (Twin pack) LUMILAMPLB - Left LUMILAMPRB - Right
Voltage: 12-24 Volt 12-24 Volt 12-24 Volt
Cable: 40cm Hard wired 40cm Hard wired 40cm Hard wired
Packaging: Blister hang/stand & carry pack left/right sides Box of 1 Left hand side Box of 1 Right hand side
Current: @13.8Volts (Stop-0.55Amps) (Tail-0.51Amps) (Ind-0.58Amps) (Rev-0.48Amps) - @28Volts (Stop-0.27Amps) (Tail-0.26Amps) (Ind-0.27Amps) (Rev-0.32Amps).
C.R.n: (Stop/tail 42101) (Indicator 42103) (Reverse 41986) (Reflector 42102)
Fitting: Surface mount to flat surface using bolts in back of lamp, run wire through hole in fixing surface. Please refer to ADR 13/00 for mounting instructions.
• LUMILAMPLB • LUMILAMPRB• Stop/Tail • Indicator • Reverse • Reflector
combination Lamp - 390mm x 150mm x 44mm
390mm
44mm
150mm
150mm
ADR/ECE approved
WARRAnTY
5
YEAR
• 135CARWML• Stop/Tail • Indicator • Reverse
Product Description:
Made for the European market, one model includes a licence plate lamp. These lamps are fully submersible, shock resistant and comes with a 5 year warranty.
Part no 140STIM 140STILM
Voltage: 12-24 Volt 12-24 Volt
30 Information Correct at time of printing
• MaXilamp3XR• MaXilamp3XRB• MaXilamp3XRR • Stop/Tail • Indicator • Reverse • Reflex Reflector
• MaXilamp1XRE• Stop/Tail • Indicator • Reflector
Product Description:
These lamps are fully submersible, rust proof, shock resistant, dust proof and feature incredibly bright LED illumination. The circuit board is fully encased in resin and cannot be penetrated by air or water, the high impact acrylic outer cover has a high resistance to the chemicals in cleaning fluids and enhanced UV protection against fading .
Part no MaXilamp1XRE
Voltage: 12-24 Volt
Cable: 40cm Sheathed tinned copper wire.
Packaging: Blister pack of 1
Current: @13.8Volts (Stop-0.34Amps) (Tail-0.07Amps) (Ind-0.37Amps) @28Volts (Stop-0.17Amps) (Tail-0.06Amps) (Ind-0.16Amps)
C.R.n: Complies with A.D.R under E.C.E approval. E9 02 R1-S1 01 2a Component number 6064
Fitting: Surface mount to flat surface using bolts in back of lamp, run wire through hole in fixing surface. Please refer to ADR 13/00 for mounting instructions.
combination Lamp - 125mm Diameter
combination Lamp - 370mm x 135mm x 40mm
125mm
40mm
45mm
Product Description:
These lamps are fully submersible, rust proof, shock resistant, dust proof and feature incredibly bright LED illumination. The circuit board is fully encased in resin and cannot be penetrated by air or water, the high impact acrylic outer cover has a high resistance to the chemicals in cleaning fluids and enhanced UV protection against fading.
Part no MaXilamp3XRR MaXilamp3XR MaXilamp3XRB
Voltage: 12-24 Volt 12-24 Volt 12-24 Volt
Cable: 40cm Hard wired 40cm Hard wired 40cm Hard wired
Packaging: Blister of 1 Blister of 1 Box of 1
Current: 3XR - @13.8V (Stop-0.54Amps) (Tail-0.08Amps) (Ind-0.77Amps) (Rev-0.67Amps) - @28V (Stop-0.27Amps) (Tail-0.04Amps) (Ind-0.35Amps) (Rev-0.34Amps).
C.R.n: (Stop/tail 40963) (Ind 40962) (Rev 40961) (Ref 38102)
Fitting: Surface mount to flat surface using bolts in back of lamp, run wire through hole in fixing surface. Please refer to ADR 13/00 for mounting instructions.
370mm
40mm
269mm
135mm
ADR/ECE approved
ADR approved
• MaXilamp5XR• MaXilamp5XRR• MaXilamp5XRB• Stop/Tail • Indicator • Reverse • Reflex Reflector
Product Description:
These lamps are fully submersible, rust proof, shock resistant, dust proof and feature incredibly bright LED illumination. The circuit board is fully encased in resin and cannot be penetrated by air or water, the high impact acrylic outer cover has a high resistance to the chemicals in cleaning fluids and enhanced UV protection against fading.
Part no MaXilamp5XRR MaXilamp5XR MaXilamp5XRB
Voltage: 12-24 Volt 12-24 Volt 12-24 Volt
Cable: 40cm Hard wired 40cm Hard wired 40cm Hard wired
Packaging: Blister of 1 Blister of 1 Box of 1
Draw: @13.8V - 5XR-5XRR (Stop-1.12Amps) (Tail-0.09Amps) (Ind-0.62Amps) (Rev-0.08Amps) @ 28V - 5XR-5XRR (Stop-0.73Amps) (Tail-0.04Amps) (Ind-0.31Amps) (Rev-0.36Amps)
C.R.n: (Stop/tail 40966) (Indicator 40964) (Reverse 40965) (Reflector 38102)
Fitting: Surface mount to flat surface using bolts in back of lamp, run wire through hole in fixing surface. Please refer to ADR 13/00 for mounting instructions.
combination Lamp - 600mm x 135mm x 40mm
600mm
40mm
500mm
135mm
ADR approved
WARRAnTY
WARRAnTY
WARRAnTY
7
YEAR
7
YEAR
7
YEAR
31Information Correct at time of printing
• MaXilamp5XC• MaXilamp5XCW• Stop/Tail • Indicator • Reverse • Reflex Reflector
600mm
40mm
500mm
135mm
Product Description:
These lamps are fully submersible, rust proof, shock resistant, dust proof and feature incredibly bright LED illumination. The circuit board is fully encased in resin and cannot be penetrated by air or water, the high impact acrylic outer cover has a high resistance to the chemicals in cleaning fluids and enhanced UV protection against fading .
Part no MaXilamp1XC
Voltage: 12-24 Volt
Cable: 40cm Sheathed tinned copper wire.
Packaging: Blister pack of 1
Current: @13.8Volts (Stop-0.34Amps) (Tail-0.07Amps) (Ind-0.37Amps) @28Volts (Stop-0.17Amps) (Tail-0.06Amps) (Ind-0.16Amps)
C.R.n: Complies with A.D.R under E.C.E approval. E9 02 R1-S1 01 2a Component number TBA
Fitting: Surface mount to flat surface using bolts in back of lamp, run wire through hole in fixing surface. Please refer to ADR 13/00 for mounting instructions.
combination Lamp - 125mm Diameter
Product Description:
These lamps are fully submersible, rust proof, shock resistant, dust proof and feature incredibly bright LED illumination. The circuit board is fully encased in resin and cannot be penetrated by air or water, the high impact acrylic outer cover has a high resistance to the chemicals in cleaning fluids and enhanced UV protection against fading.
Part no MaXilamp3XC MaXilamp3XCW
Voltage: 12-24 Volt 12-24 Volt
Cable: 40cm Hard wired 40cm Hard wired
Packaging: Blister of 1 Blister of 1
Current: @13.8V (Stop-0.54Amps) (Tail-0.08Amps) (Ind-0.77Amps) (Rev-0.67Amps) - @28V (Stop-0.27Amps) (Tail-0.04Amps) (Ind-0.35Amps) (Rev-0.34Amps).
C.R.n: (Stop/tail 42689) (Ind 42683) (Rev 42684) (Ref 42507)
Fitting: Surface mount to flat surface using bolts in back of lamp, run wire through hole in fixing surface. Please refer to ADR 13/00 for mounting instructions.
ADR/ECE approved
Product Description:
These lamps are fully submersible, rust proof, shock resistant, dust proof and feature incredibly bright LED illumination. The circuit board is fully encased in resin and cannot be penetrated by air or water, the high impact acrylic outer cover has a high resistance to the chemicals in cleaning fluids and enhanced UV protection against fading.
Part no MaXilamp5XC MaXilamp5XCW
Voltage: 12-24 Volt 12-24 Volt
Cable: 40cm Hard wired 40cm Hard wired
Packaging: Blister of 1 Blister of 1
Draw: @13.8V - (Stop-1.12Amps) (Tail-0.09Amps) (Ind-0.62Amps) (Rev-0.08Amps) @ 28V - (Stop-0.73Amps) (Tail-0.04Amps) (Ind-0.31Amps) (Rev-0.36Amps)
C.R.n: (Stop/tail 42689) (Indicator 42683) (Reverse 42684) (Reflector 42507)
Fitting: Surface mount to flat surface using bolts in back of lamp, run wire through hole in fixing surface. Please refer to ADR 13/00 for mounting instructions.
combination Lamp - 600mm x 135mm x 40mmADR
approved
• MaXilamp1XC• Stop/Tail • Indicator • Reflector
125mm
40mm
45mm
• MaXilamp3XC• MaXilamp3XCW• Stop/Tail • Indicator • Reverse • Reflex Reflector
370mm
40mm
269mm
135mm
370mm
40mm
269mm
135mm
combination Lamp - 370mm x 135mm x 40mm
WARRAnTY
WARRAnTY
WARRAnTY
7
YEAR
7
YEAR
7
YEAR
ADR approved
32 Information Correct at time of printing
237mm
25mm
18mm
19mm
216mm
203mm
• 235R • 235R24 • Stop/Tail • 235A • 235A24 • Indicator • 235W • 235W24 • Supplementary Reverse (No ADR approval)
Description: The 235 series lamps are fully submersible, shock resistant and are ADR compliant. They are a recessed mount with rubber grommet supplied.
Part no 235R 235A 235W 235A24 235R24 235W24
Voltage: 12 Volt 12 Volt 12 Volt 24 Volt 24 Volt 24 Volt
Cable: 40cm Hard wired 40cm Hard wired 40cm Hard wired 40cm Hard wired 40cm Hard wired 40cm Hard wired
Current: @13.8Volts (Stop-0.14Amps) (Tail-0.04Amps) (Ind-0.16Amps) (Rev-0.12Amps) - @28Volts (Stop-0.13Amps) (Tail-0.05Amps) (Ind-0.12Amps) (Rev-0.06Amps).
C.R.n: (Stop/tail 37678) (Indicator 39092)
Fitting: Mount onto flat surface horizontally to the ground and run wires through back. Push lamp and grommet into cutout (cut out 203mm x 19mm) in mounting surface and fix with screws supplied at both ends. Please refer to ADR13/00 for mounting instructions.
recessed strip Lamps - 237mm x 25mm x 18mm
237mm
25mm
18mm
19mm
216mm
203mm
Cut out size237mm
25mm
18mm
19mm
216mm
203mm
WARRAnTY
5
YEAR
Product Description: The 25 series lamps are fully submersible, shock resistant and are ADR compliant with ECE approval (except reverse lamp).
Part no 25R12 25A12 25W12
Voltage: 12 Volt 12 Volt 12 Volt
Cable: 40cm Hard wired 40cm Hard wired 40cm Hard wired
Current: @13.8Volts (Stop-0.28Amps) (Tail-0.03Amps) (Ind-0.20Amps) (Rev-0.16Amps)
C.R.n: These lamps comply with ADR under ECE approval (Stop/Tail E9 02 R1 S1 - 6281) (Indicator E9 01 2a - 6021)
Fitting: Mount onto flat surface horizontally to the ground and run wires through back. Push lamp into cutout (106mm x 19mm) in mounting surface, fix with screws supplied at both ends. Please refer to ADR13/00 for mounting instructions.
• 25R12• Stop/Tail
• 25A12• Indicator
• 25W12• Supplementary Reverse (No ECE approval)
recessed strip Lamps - 130mm x 25mm x 12.5mm
130mm
106mm
25mm
19mm
12.5mm
130mm
106mm
25mm
19mm
12.5mm
130mm
106mm
25mm
19mm
12.5mm
Cut out size
ECE approved
WARRAnTY
5
YEAR
ADR/ECE approved
• 380R • 380R24• Stop/Tail
• 380A • 380A24• Indicator
• 380W • 380W24• Supplementary Reverse (No ADR approval)
Description: The 380 series lamps are fully submersible, shock resistant and are ADR compliant. They are a recess mounted with rubber grommet supplied.
Part no 380R 380A 380W 380R24 380A24 380W24
Voltage: 12 Volt 12 Volt 12 Volt 24 Volt 24 Volt 24 Volt
Cable: 40cm Hard wired 40cm Hard wired 40cm Hard wired 40cm Hard wired 40cm Hard wired 40cm Hard wired
Current: @13.8Volts (Stop-0.16Amps) (Tail-0.04Amps) (Ind-0.18Amps) (Rev-0.14Amps) - @28Volts (Stop-0.12Amps) (Tail-0.01Amps) (Ind-0.10Amps) (Rev-0.09Amps).
C.R.n: (Stop/tail 39473) (Indicator 39470)
Fitting: Mount onto flat surface horizontally to the ground and run wires through back. Push lamp and grommet into cutout (cut out 348mm x 19mm) in mounting surface and fix with screws supplied at both ends. Please refer to ADR13/00 for mounting instructions.
382mm
25mm
18mm
19mm
361mm
348mm
recessed strip Lamps - 382mm x 25mm x 18mm
Cut out size
WARRAnTY
5
YEAR
ADR/ECE approved
33Information Correct at time of printing
square single Lamp - 100mm x 100mm x 28mm
square single Lamp - 122mm x 122mm x 31mm
Product Description:
The 100 series lamps are fully submersible, shock resistant and feature our hexagonal lens pattern. Specifically designed for trailers or medium sized commercial vehicles. Individual clip in lenses allow easy surface mount with no visible screws.
Part no 100RM 100RMB 100AM 100AMB 100WM 100WMB
Voltage: 12-24 Volt 12-24 Volt 12-24 Volt 12-24 Volt 12-24 Volt 12-24 Volt
Cable: 40cm 40cm 40cm 40cm 40cm 40cm
Packaging: Blister of 1 Box of 1 Blister of 1 Box of 1 Blister of 1 Box of 1
Current: @13.8Volts (Stop-0.38Amps) (Tail-0.04Amps) (Ind-0.38Amps) (Rev-0.31Amps) - @28Volts (Stop-0.24Amps) (Tail-0.07Amps) (Ind-0.23Amps) (Rev-0.17Amps) Each lens
C.R.n: Single function lens (Stop/tail 33402) (Indicator 33156) (Reverse 35793)
Fitting: Surface mount bracket, run wires through back and clip lens into place. Please refer to ADR 13/00 for mounting instructions.
• 80RM• 80RMB• 80RB• Stop/Tail
• 100RM• 100RMB• Stop/Tail
• 80AM• 80AMB• 80AB• Indicator
• 100AM• 100AMB• Indicator
• 80WM• 80WMB• 80WB• Reverse
• 100WM• 100WMB• Reverse
Product Description:
The 80 series lamps are fully submersible, shock resistant and feature our hexagonal lens pattern. Specifically designed for trailers or small sized commercial vehicles. Individual clip in lenses allow easy surface mount with no visible screws.
Part no 80RM 80RMB 80RB 80AM 80AMB 80AB 80WM 80WMB 80WB
Voltage: 12-24 Volt 12-24 Volt 12 Volt 12-24 Volt 12-24 Volt 12 Volt 12-24 Volt 12-24 Volt 12 Volt
Cable: 40cm 40cm 40cm 40cm 40cm 40cm 40cm 40cm 40cm
Packaging: Blister of 1 Box of 1 Box of 1 Blister of 1 Box of 1 Box of 1 Blister of 1 Box of 1 Box of 1
Current: @13.8Volts (Stop-0.33Amps) (Tail-0.06Amps) (Ind-0.31Amps) (Rev-0.29Amps) - @28Volts (Stop-0.25Amps) (Tail-0.04Amps) (Ind-0.22Amps) (Rev-0.21Amps) Each lens
C.R.n: (Stop/tail 33059) (Indicator 33098) (Reverse 35797)
Fitting: Surface mount bracket, run wires through back and clip lens into place. Please refer to ADR 13/00 for mounting instructions.
100mm 28mm
100mm
122mm 31mm
122mm
Product Description:
The 125 series lamps are fully submersible, shock resistant and feature our hexagonal lens pattern. Specifically designed for trailers or large sized commercial vehicles. Individual clip in lenses allow easy surface mount with no visible screws.
Part no 125RM 125RMB 125AM 125AMB 125WM 125WMB
Voltage: 12-24 Volt 12-24 Volt 12-24 Volt 12-24 Volt 12-24 Volt 12-24 Volt
Cable: 40cm Hard wired 40cm Hard wired 40cm Hard wired 40cm Hard wired 40cm Hard wired 40cm Hard wired
Packaging: Blister of 1 Poly Bag of 1 Blister of 1 Poly Bag of 1 Blister of 1 Poly Bag of 1
Current: @13.8Volts (Stop-0.42Amps) (Tail-0.04Amps) (Ind-0.43Amps) (Rev-0.36Amps) - @28Volts (Stop-0.26Amps) (Tail-0.06Amps) (Ind-0.25Amps) (Rev-0.18Amps).
C.R.n: (Stop/tail 33403) (Indicator 33165) (Reverse 35794)
Fitting: Surface mount bracket, run wires through back and clip lens into place. Please refer to ADR 13/00 for mounting instructions.
• 125RM • 125RMB• Stop/Tail
• 125AM • 125AMB• Indicator
• 125WM • 125WMB• Reverse
square single Lamp - 147mm x 147mm x 31mm
147mm 31mm
147mm
ADR/ECE approved
ADR/ECE approved
ADR/ECE approved
WARRAnTY
WARRAnTY
WARRAnTY
5
YEAR
5
YEAR
5
YEAR
34 Information Correct at time of printing
• 200BAAM• Indicator
• 200CRRM• Stop/Tail
Product Description:
Fully submersible with the rear of the circuit board encased in resin, rust proof & shock resistant. Featuring our hexagonal lens pattern, and designed to fit into small spaces with individual clip in lenses for easy replacement. Surface mounted with no visible screws and 40cm of hard wired cable.
Part no 200BRRRM 200CRRRM 200BAAAM 200CAAAM
Voltage: 12-24 Volt 12-24 Volt 12-24 Volt 12-24 Volt
Packaging: Blister of 1 Blister of 1 Blister of 1 Blister of 1
Current: @13.8V (Stop-0.32Amps) (Tail-0.04Amps) (Ind-0.34Amps) (Rev-0.17Amps) - @28V (Stop-0.18Amps) (Tail-0.04Amps) (Ind-0.19Amps) (Rev-0.18Amps) Each lens
C.R.n: (Stop/tail 35941) (Indicator 35795)
Fitting: Surface mount bracket onto flat surface horizontally to the ground with bolts provided, run wires through back and clip lens into place. Please refer to ADR 13/00 for mounting instructions.
• 200BRM• 200BRMB• Stop/Tail
• 200CRM• Stop/Tail
• 200BAM• 200BAMB• Indicator
• 200CAM• Indicator
• 200BWM• 200BWMB• Reverse
• 200CWM• Reverse
single rectangular Lamp - 200mm x 50mm x 28mm
28mm
200mm
50mm28mm
200mm
50mm
Double rectangular Lamp - 200mm x 92mm x 28mm
Triple rectangular Lamp - 200mm x 134mm x 28mm
• 200BRRM• Stop/Tail
• 200CAAM• Indicator
28mm
200mm
92mm
Product Description:
Fully submersible with the rear of the circuit board encased in resin, rust proof & shock resistant. Featuring our hexagonal lens pattern, and designed to fit into small spaces with individual clip in lenses for easy replacement. Surface mounted with no visible screws and 40cm of hard wired cable.
Part no 200BRRM 200CRRM 200BAAM 200CAAM
Voltage: 12-24 Volt 12-24 Volt 12-24 Volt 12-24 Volt
Packaging: Blister of 1 Blister of 1 Blister of 1 Blister of 1
Current: @13.8V (Stop-0.32Amps) (Tail-0.04Amps) (Ind-0.34Amps) (Rev-0.17Amps) - @28V (Stop-0.18Amps) (Tail-0.04Amps) (Ind-0.19Amps) (Rev-0.18Amps) Each lens
C.R.n: (Stop/tail 35941) (Indicator 35795)
Fitting: Surface mount bracket onto flat surface horizontally to the ground with bolts provided, run wires through back and clip lens into place. Please refer to ADR 13/00 for mounting instructions.
• 207A12• Indicator
• 207R12• Stop/Tail
Product Description:
Fully submersible with the rear of the circuit board encased in resin, rust proof & shock resistant. Featuring our hexagonal lens pattern, and designed to fit into small spaces with individual clip in lenses for easy replacement. Surface mounted with no visible screws and 40cm of hard wired cable.
Part no 200BRM 200BRMB 200CRM 200BAM 200BAMB 200CAM 200BWM 200BWMB 200CWM 207R12 207A12
Voltage: 12-24 Volt 12-24 Volt 12-24 Volt 12-24 Volt 12-24 Volt 12-24 Volt 12-24 Volt 12-24 Volt 12-24 Volt 12 Volt 12 Volt
Packaging: Blister of 1 Box of 1 Blister of 1 Blister of 1 Box of 1 Blister of 1 Blister of 1 Box of 1 Blister of 1 Bag of 1 Bag of 1
Current: 200 series - @13.8Volts (Stop-0.32Amps) (Tail-0.04Amps) (Ind-0.39Amps) (Rev-0.34Amps) - @28Volts (Stop-0.18Amps) (Tail-0.04Amps) (Ind-0.19Amps) (Rev-0.18Amps) 207 series - @13.8Volts (Stop-0.18Amps) (Tail-0.07Amps) (Ind-0.17Amps)
C.R.n: (Stop/tail 35941) (Indicator 35795) (Reverse 35796)
Fitting: Surface mount bracket horizontally, run wires through back and clip lens into place. Please refer to ADR 13/00 for mounting instructions.
ADR/ECE approved
• Indicator• 200BAAAM
• Indicator• 200CAAAM
• Stop/Tail • 200BRRRM
• Stop/Tail • 200CRRRM
28mm
200mm
134mm
WARRAnTY
5
YEAR
WARRAnTY
5
YEAR
WARRAnTY
5
YEAR
ADR/ECE approved
ADR/ECE approved
35Information Correct at time of printing
Product Description:
The 135 series lamps are fully submersible, shock resistant and feature our diamond lens pattern excellent for small tight spaces. Individual push in bracket mounted lenses for surface mount with no visible screws.
Part no 135RM 135AM 135WM
Voltage: 12-24 Volt 12-24 Volt 12-24 Volt
Cable: 40cm Hard wired 40cm Hard wired 40cm Hard wired
Current: @13.8Volts (Stop-0.11Amps) (Tail-0.02Amps) (Ind-0.16Amps) (Rev-0.23Amps) - @28Volts (Stop-0.08Amps) (Tail-0.02Amps) (Ind-0.06Amps) (Rev-0.19Amps)
C.R.n: (Stop/tail 39848) (Indicator 39845) (Reverse 39849)
Fitting: Surface mount horizontally to the ground with screws or plugs provided, run wires through back & clip lens into place. Refer to ADR 13/00 for mounting instructions.
rectangular Lamps - 135mm x 38mm x 24mm
• 135RM• Stop/Tail
• 135AM• Indicator
• 135WM• Reverse
135mm
145mm
133mm
38mm
48mm
36mm
24mm
21mm
80mm
135mm
145mm
133mm
38mm
48mm
36mm
24mm
21mm
80mm
135mm
145mm
133mm
38mm
48mm
36mm
24mm
21mm
80mm
ADR/ECE approved
Product Description:
The 135 series lamps are fully submersible, shock resistant and feature our diamond lens pattern excellent for small tight spaces. Individual push in grommet mounted lenses for recessed fit with no visible screws.
Part no 135RMG 135AMG 135WMG
Voltage: 12-24 Volt 12-24 Volt 12-24 Volt
Cable: 40cm Hard wired 40cm Hard wired 40cm Hard wired
Current: @13.8Volts (Stop-0.11Amps) (Tail-0.02Amps) (Ind-0.16Amps) (Rev-0.23Amps) - @28Volts (Stop-0.08Amps) (Tail-0.02Amps) (Ind-0.06Amps) (Rev-0.19Amps)
C.R.n: (Stop/tail 39848) (Indicator 39845) (Reverse 39849)
Fitting: Recess mount horizontally to the ground with grommet provided, run wires through back & push lens into place, (cut out for grommet 133mm x 36mm) . Refer to ADR 13/00 for mounting instructions.
recessed Lamps - 145mm x 48mm x 21mm
• 135RMG• Stop/Tail
• 135AMG• Indicator
• 135WMG• Reverse
135mm
145mm
133mm
38mm
48mm
36mm
24mm
21mm
80mm
135mm
133mm
38mm
36mm
24mm
21mm
80mm
135mm
145mm
133mm
38mm
48mm
36mm
24mm
21mm
80mm
Cut out size
ADR/ECE approved
WARRAnTY
5
YEAR
WARRAnTY
5
YEAR
• 380CR12 • Stop/Tail
• 380CA12• Indicator
• 380CW12• Supplementary Reverse No ADR/ECE Approval
slimline strip Lamps - 404mm x 46mm x 17mm
Product Description:
The 380 series lamps have been released and blister packed with a chrome bracket that allows them to be surface mounted without the need for a cut out. The brackets are also available separately in chrome, white and black.
Part no 380CR12 380CA12 380CW12
Voltage: 12 Volt only 12 Volt only 12 Volt only
Cable: 40cm 40cm 40cm
Current: @13.8Volts (Stop-0.16Amps) (Tail-0.04Amps) (Ind-0.18Amps) (Rev-0.14Amps) - @28Volts (Stop-0.12Amps) (Tail-0.01Amps) (Ind-0.10Amps) (Rev-0.09Amps).
C.R.n (Stop/tail 39473) (Indicator 39470)
Fitting: Surface mount bracket and lights horizontally to ground with screws provided, please refer to ADR 13/00 for mounting instructions.
404mm
46mm
17mm
361mm
ADR/ECE approved
nEW
PRODUCT
WARRAnTY
5
YEAR
36 Information Correct at time of printing
• 131AM• Indicator
• 131WM• Reverse
Product Description:
The 131 series lamps are fully water proof and shock resistant. ADR compliant for both horizontal or vertical mount. They are retro fit to same shape designs. Grommet (59401) or bracket (59401B or 59401C).
Part no 131RM 131CRM 131AM 131CAM 131WM
Voltage: 12-24 Volt 12-24 Volt 12-24 Volt 12-24 Volt 12-24 Volt
Cable: 15cm 15cm 15cm 15cm 15cm
Packaging: Blister of 1 Blister of 1 Blister of 1 Blister of 1 Blister of 1
Current: @13.8Volts (Stop-TBAAmps) (Tail-TBAAmps) (Ind-TBAAmps) (Rev-TBAAmps) - @28Volts (Stop-TBAAmps) (Tail-TBAAmps) (Ind-TBAAmps) (Rev-TBAAmps)
C.R.n: (Stop/tail TBA) (Indicator TBA) (Reverse TBA)
Fitting: Retro fit to existing rectangle lamps. If new installation, fit grommet or flange into cutout (cut out 139mm x 91mm), run wires through back then push into grommet/flange. Please refer to ADR 13/00 for mounting instructions.
recessed Lamps - 134mm x 87mm x 25mm
• 131RM• Stop/Tail
87mm
25mm
134mm
• 131CAM• Indicator• Clear Lens • Amber LEDs
• 131CRM• Stop/Tail• Clear Lens • Red LEDs
Product Description:
The 5590 series lamps are fully submersible and shock resistant. ADR compliant for vertical position. They are retro fit to same shape designs. Plug (53102), grommet (59101) or bracket (59401B or 59401C) required if new installation. No ADR on the reverse lamp.
Part no 5590RM 5590AM 5590WM
Voltage: 12-24 Volt 12-24 Volt 12-24 Volt
Plug: Part no. 53102 Part no. 53102 Part no. 53102
Packaging: Poly bag of 1 Poly bag of 1 Poly bag of 1
Current: @13.8Volts (Stop-0.27Amps) (Tail-0.06Amps) (Ind-0.28Amps) (Rev-0.42Amps) - @28Volts (Stop-0.22Amps) (Tail-0.04Amps) (Ind-0.20Amps) (Rev-0.25Amps).
C.R.n: (Stop/tail 33167) (Indicator 33270)
Fitting: Retro fit to existing rectangle lamps. If new installation, fit grommet or flange into cutout (cut out 139mm x 91mm), plug wire into lamp and run through back then push into grommet/flange. Please refer to ADR 13/00 for mounting instructions.
recessed Lamps - 134mm x 86mm x 50mm
• 5590RM• Stop/Tail
• 5590AM• Indicator
• 5590WM• Reverse (No ADR)
50mm
134mm
86mm
117mm
109mm
91mm
89mm
44mm
167mm
157mm
139mm
136mm
12mm
Cut out size
Cut out size
ADR approved
ADR approved
5
YEAR WARRAnTY
WARRAnTY
5
YEAR
nEW
PRODUCT
nEW
PRODUCT nEW
PRODUCT
nEW
PRODUCT nEW
PRODUCT
Cut out size
139mm
91mm
Bracket
Grommet
37Information Correct at time of printing
Product Description:
The 130 series lamps are fully submersible, shock resistant and feature our hexagonal lens pattern. ADR compliant for both horizontal or vertical mount. They are retro fit to same shape designs. Plug (53102), grommet (59401) or bracket (59401B or 59401C) required if new installation.
Part no 130RM 130RM 130RM-1 130RMB-1 130AM 130AMB 130WM
Voltage: 12-24 Volt 12-24 Volt 12-24 Volt 12-24 Volt 12-24 Volt 12-24 Volt 12-24 Volt
Plug: Part no. 53102 Part no. 53102 Part no. 53102 Part no. 53102 Part no. 53102 Part no. 53102 part no. 53102
Packaging: Blister of 1 Poly bag of 1 Blister of 1 Poly bag of 1 Blister of 1 Poly bag of 1 Blister of 1
Current: @13.8Volts (Stop-0.23Amps) (Tail-0.03Amps) (Ind-0.20Amps) (Rev-0.15Amps) - @28Volts (Stop-0.12Amps) (Tail-0.04Amps) (Ind-0.14Amps) (Rev-0.08Amps)
C.R.n: (Stop/tail RM-1 40655) (Stop/tail RM 36844) (Indicator 36843) (Reverse 36845) (Reflector 38102)
Fitting: Retro fit to existing rectangle lamps. If new installation, fit grommet or flange into cutout (cut out 139mm x 91mm), plug wire into lamp and run through back then push into grommet/flange. Please refer to ADR 13/00 for mounting instructions.
• 130RM• 130RMB• Stop/Tail/ Reflector
• 130AM• 130AMB• Indicator
• 130RM-1• Stop/Tail
• 130WM• Reverse
86mm
48mm
134mm
Product Description:
The 5940 series lamps are fully submersible and shock resistant. They are retro fit to same shape designs. Plug (53102), grommet (59401) or bracket (59401B or 59401C).
Part no 5940R 5940A 5940W
Voltage: 12 Volt 12 Volt 12 Volt
Plug: part no. 53102 part no. 53102 part no. 53102
Packaging: Poly bag of 1 Poly bag of 1 Poly bag of 1
Current: @13.8Volts (Stop-0.57Amps) (Tail-0.08Amps) (Ind-0.60Amps) (Rev-0.23Amps)
C.R.n: N/A
Fitting: Retro fit to existing fittings. If new installation fit grommet or flange into cutout (cut out 139mm x 91mm) plug wire into lamp and run through back then push into grommet/flange.
• 5940R• Stop/Tail
• 5940A• Indicator
• 5940W• Reverse
recessed Lamps - 134mm x 86mm x 48mm
86mm
48mm
134mm
recessed Lamps - 134mm x 86mm x 48mm
113mm
109mm
91mm
89mm
24mm
160mm
157mm
139mm
136mm
12mm
Cut out size
ADR/ECE approvedVertical
Horizontal
DOT/SAEapproved
5
YEAR WARRAnTY
WARRAnTY
5
YEAR
Cut out size
113mm
109mm
91mm
89mm
24mm
160mm
157mm
139mm
136mm
12mm
139mm
91mm
Cut out size
BracketGrommet
38 Information Correct at time of printing
Product Description: The 102 series lamps are water proof, shock resistant and feature bright output with an attractive inner lens design and low profile exterior.
Part no 102R 102RM 102A 102AM 102W 102WM 102RC 102AC
Voltage: 12 Volt 12-24 Volt 12 Volt 12-24 Volt 12 Volt 12-24 Volt 12 Volt 12 Volt
Cable: 36cm 36cm 36cm 36cm 36cm 36cm 36cm 36cm
Packaging: Poly Bag of 1 Blister of 1 Poly Bag of 1 Blister of 1 Poly Bag of 1 Blister of 1 Poly Bag of 1 Poly Bag of 1
Current: @13.8Volts (Stop-0.34Amps) (Tail-0.04Amps) (Ind-0.61Amps) (Rev-0.27Amps) - @28Volts (Stop-TBAAmps) (Tail-TBAAmps) (Ind-TBAAmps) (Rev-TBAAmps).
C.R.n: (Stop/tail 42963) (Indicator 42832) (Reverse 42826)
Fitting: Fit into cutout (cutout 104mm round) using stick on gasket between lamp and fitting surface, run wires at back. Please refer to ADR 13/00 for mounting instructions.
• 102R• 102RM• Stop/Tail
• 110RM• 110RMB• Stop/Tail
• 102RC• Stop/Tail
• 102AC• Indicator
• 102A• 102AM• Indicator
• 110AM• 110AMB• Indicator
• 102W• 102WM• Reverse
• 110WM• 110WMB• Reverse
Product Description:
The 110 series lamps are fully submersible, shock resistant and feature our hexagonal lens pattern. These lamps retro fit to same shape designs. Plug (53102), grommet (53101) or bracket (53101B or 53101C) required if new installation.
Part no 110RM 110RMB 110AM 110AMB 110WM 110WMB
Voltage: 12-24 Volt 12-24 Volt 12-24 Volt 12-24 Volt 12-24 Volt 12-24 Volt
Plug: Part no. 53102 Part no. 53102 Part no. 53102 Part no. 53102 Part no. 53102 Part no. 53102
Packaging: Blister of 1 Poly Bag of 1 Blister of 1 Poly Bag of 1 Blister of 1 Poly Bag of 1
Current: @13.8Volts (Stop-0.23Amps) (Tail-0.08Amps) (Ind-0.16Amps) (Rev-0.21Amps) - @28Volts (Stop-0.14Amps) (Tail-0.02Amps) (Ind-0.13Amps) (Rev-0.15Amps).
C.R.n: (Stop/tail 35299) (Indicator 35298) (Reverse 36102)
Fitting: Retro fit to existing 4 inch lamps. If new installation fit grommet or flange into cutout (Cut out 115mm round) plug wire into lamp and run through back then push into grommet/flange. Please refer to ADR 13/00 for mounting instructions.
recessed Lamps - 130mm Diameter x 42mm high
recessed Lamps - 109mm Diameter x 53mm high
130mm
42mm
116mm
104mm
109mm
53mm
135mm 115mm 113mm142mm
25mm 15mm
ADR/ECE approved
ADR/ECE approved
5
YEAR WARRAnTY
5
YEAR WARRAnTY
nEW
PRODUCT nEW
PRODUCT nEW
PRODUCT
nEW
PRODUCT nEW
PRODUCT
Cut out size
BracketGrommet
39Information Correct at time of printing
Product Description:
The 5570 series lamps are fully submersible. These lamps are an American design and pass DOT/SAE. They are retro fit to same shape designs. Plug (53102), grommet (53101) or bracket (53101B or 53101C) required if new installation.
Part no 5570R 5570A 5570W
Voltage: 12 Volt 12 Volt 12 Volt
Plug: Use part no. 53102 Use part no. 53102 Use part no. 53102
Current: @13.8Volts (Stop-0.42Amps) (Tail-0.02Amps) (Ind-0.42Amps) (Rev-0.78Amps)
Fitting: Retro fit to existing fittings if new installation fit grommet or flange into cutout (cut out 115mm diameter) plug wire into lamp and run through back then push into grommet/flange.
• 5570R• Stop/Tail
• 5570A• Indicator
• 5570W• Reverse
recessed Lamps - 109mm Diameter x 56mm high
recessed Lamps - 109mm Diameter x 56mm high
Product Description:
The 5575 series lamps are fully submersible. These lamps are an American design and pass DOT/SAE. They are retro fit to same shape designs. Plug (53102), grommet (53101) or bracket (53101B or 53101C) required if new installation.
Part no 5575R 5575A 5575W
Voltage: 12 Volt 12 Volt 12 Volt
Plug: Use part no. 53102 Use part no. 53102 Use part no. 53102
Current: @13.8Volts (Stop-0.34Amps) (Tail-0.28Amps) (Ind-0.42Amps) (Rev-0.66Amps)
Fitting: Retro fit to existing fittings if new installation fit grommet or flange into cutout (cut out 115mm diameter) plug wire into lamp and run through back then push into grommet/flange.
• 5575R• Stop/Tail
• 5575A• Indicator
• 5575W• Reverse
109mm
56mm
115mm
109mm
56mm
115mm
• 5523R• Stop/Tail
• 5523A• Indicator
• 5525W• Reverse
recessed Lamps - 109mm Diameter x 39mm high
109mm
39mm
115mm
Product Description:
The 5523 series lamps are fully submersible. These lamps are an American design and pass DOT/SAE. They are retro fit to same shape designs. Plug (55062), grommet (53101) or bracket (53101B or 53101C) required if new installation.
Part no 5523R 5523A 5525W
Voltage: 12 Volt 12 Volt 12 Volt
Plug: Use part no. 55062 Use part no. 55062 Use part no. 55062
Current: @13.8Volts (Stop-0.27Amps) (Tail-0.07Amps) (Ind-0.26Amps) (Rev-0.29Amps)
Fitting: Retro fit to existing fittings if new installation fit grommet or flange into cutout (cut out 115mm diameter) plug wire into lamp and run through back then push into grommet/flange.
DOT/SAE approved
DOT/SAE approved
DOT/SAE approved
WARRAnTY
5
YEAR
WARRAnTY
5
YEAR
WARRAnTY
5
YEAR Cut
out size
Cut out size
Cut out size
40 Information Correct at time of printing
Product Description: The 5543F series lamps are fully submersible. These lamps are an American design and pass DOT/SAE. They are retro fit to same shape designs.
Part no 5543FR 5543FA 5543FW
Voltage: 12 Volt 12 Volt 12 Volt
Cable: 26cm with plug 26cm with plug 26cm with plug
Current: @13.8Volts (Stop-0.27Amps) (Tail-0.07Amps) (Ind-0.26Amps) (Rev-0.26Amps)
Fitting: Retro fit to existing fittings, plug into existing loom and fix with screws through three fixing points.
• 5543FR• Stop/Tail • Reflector
• 5543FA• Indicator • Reflector
• 5543FW• Reverse • Reflector
139mm
22mm
108mm
recessed Lamps - 139mm Diameter x 22mm high
Product Description: The 5513 series lamps are fully submersible. These lamps are an American design and pass DOT/SAE.
Part no 5513R 5513A 5513W
Voltage: 12 Volt 12 Volt 12 Volt
Plug: Use Part number 55062 Use Part number 55062 Use Part number 55062
Current: @13.8Volts (Stop-0.27Amps) (Tail-0.07Amps) (Ind-0.26Amps) (Rev-0.26Amps)
Fitting: Retro fit to existing fittings, wire into existing loom and fix with screws through three fixing points.
• 5513R• Stop/Tail
• 5513A• Indicator
• 5513W• Reverse
recessed Lamps - 140mm Diameter x 39mm high140mm
39mm
110mm
Product Description: The 5585 series lamps are fully submersible. These lamps are an American design and pass DOT/SAE.
Part no 5585R 5585A 5585W
Voltage: 12 Volt 12 Volt 12 Volt
Cable: 20cm Hard wired 20cm Hard wired 20cm Hard wired
Current: @13.8Volts (Stop-0.30Amps) (Tail-0.07Amps) (Ind-0.33Amps) (Rev-0.31Amps)
Fitting: Retro fit to existing fittings, wire into existing loom and fix with screws through four fixing points.
• 5585R• Stop/Tail
• 5585A• Indicator
• 5585W• Reverse
round Lamps - 177mm Diameter x 25mm high
25mm
158mm
158mm
177mm
• 55062
DOT/SAEapproved
DOT/SAEapproved
DOT/SAEapproved
5
YEAR WARRAnTY
5
YEAR WARRAnTY
5
YEAR WARRAnTY
Cut out size
Cut out size
41Information Correct at time of printing
Product Description:
The 5437 series lamps are fully submersible, shock resistant and have been reworked to be ADR compliant (except reverse lamp). Available as 12 volt only.
Part no 5437R 5437A 5437W
Voltage: 12 Volt 12 Volt 12 Volt
Cable: 20cm Hard wired 20cm Hard wired 20cm Hard wired
Packaging: Poly bag of 1 Poly bag of 1 Poly bag of 1
Current: @13.8Volts (Stop-0.30Amps) (Tail-0.02Amps) (Ind-0.43Amps) (Rev-0.41Amps)
C.R.n: (Stop/tail 37675) (Indicator 37674)
Fitting: Remove chrome bezel and fix lamp onto flat surface horizontally to the ground through two screw holes, run wires from back of lamp, click bezel back into place. Please refer to ADR 13/00 for mounting instructions.
• 5437R• Stop/Tail
• 5437A• Indicator
• 5437W• Reverse No ADR
28mm
94mm
200mm
184mm
28mm
94mm
200mm
184mm
Product Description: The 5543 series lamps are fully submersible. These lamps are an American design and pass DOT/SAE. They are retro fit to same shape designs.
Part no 5543R 5543A 5543W
Voltage: 12 Volt 12 Volt 12 Volt
Cable: 20cm Hard wire 20cm Hard wire 20cm Hard wire
Packaging: Poly bag of 1 Poly bag of 1 Poly bag of 1
Current: @13.8Volts (Stop-0.27Amps) (Tail-0.07Amps) (Ind-0.26Amps) (Rev-0.15Amps)
C.R.n: N/A
Fitting: Retro fit to existing fittings, wire into existing loom and fix with screws through three fixing points.
• 5543R• Stop/Tail
• 5543A• Indicator
• 5543W• Reverse
round Lamps - 144mm Diameter x 22mm high
144mm
22mm
oval Lamps - 200mm x 94mm x 28mm
DOT/SAEapproved
5
YEAR WARRAnTY
5
YEAR WARRAnTY
ADR approved
42 Information Correct at time of printing
Product Description: The 5503/5505 series lamps are fully submersible. These lamps are an American design and pass DOT/SAE. Grommet (54101), Plug (55062)
Part no 5503R 5503A 5505W
Voltage: 12 Volt 12 Volt 12 Volt
Plug: Use Part number 55062 Use Part number 55062 Use Part number 55062
Packaging: Poly bag of 1 Poly bag of 1 Poly bag of 1
Current: @13.8Volts (Stop-0.27Amps) (Tail-0.07Amps) (Ind-0.26Amps) (Rev-0.29Amps)
Fitting: Fit grommet into cutout in mounting surface, run wire through back of grommet and plug into back of lamp, push lamp into grommet.
• 5503R• Stop/Tail
• 5503A• Indicator
• 5505W• Reverse
Product Description: The 5533/5535 series lamps are fully submersible. These lamps are an American design and pass DOT/SAE.
Part no 5533R 5533A 5535W
Voltage: 12 Volt 12 Volt 12 Volt
Plug: Use Part number 55062 Use Part number 55062 Use Part number 55062
Packaging: Poly bag of 1 Poly bag of 1 Poly bag of 1
Current: @13.8Volts (Stop-0.27Amps) (Tail-0.07Amps) (Ind-0.26Amps) (Rev-0.29Amps)
Fitting: Fit lamp onto mounting surface with 4 screw points, run wire through back and plug into back of lamp.
• 5533R• Stop/Tail
• 5533A• Indicator
• 5535W• Reverse
recessed Lamps - 164mm x 58mm x 39mm
recessed Lamps - 192mm x 83mm x 39mm
• 55062
• 55062
• 54101
39mm
58mm
61mm
164mm
171mm
39mm
58mm
61mm
164mm
171mm
39mm
58mm
61mm
164mm
171mm
39mm
83mm
192mm
165mm
108mm
89mm
58mm
39mm
83mm
192mm
165mm
108mm
89mm
58mm
39mm
83mm
192mm
165mm
108mm
89mm
58mm
Product Description: The 5563 series lamps are fully submersible. These lamps are an American design and pass DOT/SAE.
Part no 5563R 5563A 5563W
Voltage: 12 Volt 12 Volt 12 Volt
Cable: 15cm Hard wired 15cm Hard wired 15cm Hard wired
Packaging: Poly bag of 1 Poly bag of 1 Poly bag of 1
Current: @13.8Volts (Stop-0.27Amps) (Tail-0.07Amps) (Ind-0.26Amps) (Rev-0.15Amps)
Fitting: Remove chrome bezel and fix to mounting surface using 4 mounting holes in lamp, run wires through back and then fit chrome bezel back onto lamp.
• 5563R• Stop/Tail
• 5563A• Indicator
• 5563W• Reverse
oblong Lamps - 191mm x 84mm x 22mm
22mm
84mm
191mm
22mm
84mm
191mm
DOT/SAEapproved
DOT/SAEapproved
DOT/SAEapproved
5 YEAR WARRAnTY
5 YEAR WARRAnTY
5 YEAR WARRAnTY
Cut out size
Cut out size
43Information Correct at time of printing
135CAT1 in active mode 135CAT1G in active mode
Product Description:
The 135 series lamps are fully submersible, shock resistant and feature our diamond lens pattern, excellent for small tight spaces. Individual push in grommet mounted lens for recessed fit or bracket mounted lenses for surface mount with no visible screws.
Part no 135CAT1 135CAT1/24 135CAT1G (Grommet)
Voltage: 12 Volt 24 Volt 12 Volt
Cable: 40cm Hard wired 40cm Hard wired 40cm Hard wired
Packaging: Blister of 1 Blister of 1 Blister of 1
Current: @13.8Volts (Front Indicator-0.39Amps) - @28Volts (Front Indicator-0.17Amps)
C.R.n: (Front Indicator 12 volt 39340, 24 volt 42131)
Fitting:
For bracket lamp, surface mount bracket onto flat surface horizontally to the ground with screws or plugs provided, run wires through back & clip lens into place.For grommet lamp, recess mount grommet into flat surface (cut out for grommet 133mm x 36mm) horizontally to the ground, run wires through back & push lens into place. Refer to ADR 13/00 for mounting instructions.
• 135CAT1• 135CAT1/24
• 135CAT1G
Front indicator Lamps - 135mm x 38mm x 24mm
Front indicator/Marker Lamps 200mm x 50mm x 28mm
Inactive Active
Product Description:
The 200 series lamps are fully submersible, shock resistant and feature our hexagonal lens pattern with a unique size designed to fit into small spaces. Individual clip in lenses allow easy surface mount with no visible screws.
Part no 200CAW 200CAW/24
Voltage: 12 volt only 24 volt only
Cable: 40cm Hard wired 40cm Hard wired
Packaging: Box of 1 Box of 1
Current: @13.8Volts (Indicator-0.44Amps) (Position-0.06Amps) - @28Volts (Indicator-0.15Amps) (Position-0.03Amps)
C.R.n: (Front Indicator 38794) (Front position 38795)
Fitting: Surface mount bracket onto flat surface horizontally to the ground with screws provided, run wires through back and clip lens into place. Please refer to ADR 13/00 for mounting instructions.
• 200CAW• 200CAW/24
135mm
145mm
133mm
38mm
48mm
36mm
24mm
21mm
80mm
135mm
145mm
133mm
38mm
48mm
36mm
24mm
21mm
80mm
135mm
145mm
133mm
38mm
48mm
36mm
24mm
21mm
80mm
135mm
145mm
133mm
38mm
48mm
36mm
24mm
21mm
80mm
135mm
145mm
133mm
38mm
48mm
36mm
24mm
21mm
80mm
200mm
28mm
50mm
Inactive Active
Product Description:
The 175 series lamps are fully submersible, shock resistant and feature our new diamond lens pattern with a unique size designed to fit into most common front bull bars. Individual clip in lenses allow easy mount to existing fitting with no visible screws.
Part no 175AW
Voltage: 12 volt only
Cable: 40cm Hard wired
Packaging: Blister of 1
Current: @13.8Volts (Indicator-0.32Amps) (Position-0.03Amps)
C.R.n: (Front Indicator 42822) (Front position 42821)
Fitting: Surface mount bracket plate onto flat surface horizontally to the ground with screws provided, run wires through back and clip lens into place. Please refer to ADR 13/00 for mounting instructions.
• 175AW
Front indicator/Marker Lamps 175mm x 50mm x 24mm
24mm
50mm
175mm
ADR/ECE approved
ADR/ECE approved
ADR/ECE approved
WARRAnTY
5
YEAR
WARRAnTY
5
YEAR
WARRAnTY
5
YEAR
Cut out size
44 Information Correct at time of printing
• 35WM• 35WMB• 35WM2• Front end outline marker
• 35CWM• 35CWMB• Front end outline marker
Product Description:
The 35 series marker lamps are fully submersible, shock resistant, feature our hexagonal lens pattern, and have a slimline design. Individual clip in lenses allow easy surface mount with no visible screws.
Part no,Packaging
35RM - Blister 35AM - Blister 35ARM - Blister 35WM - Blister
35RMB - Bulk 35AMB - Bulk 35ARMB - Bulk 35WMB - Bulk
35CRM - Blister 35CAM - Blister 35CARM - Blister 35CWM - Blister
35CRMB - Bulk 35CAMB - Bulk 35CARMB - Bulk 35CWMB - Bulk
35RM2 - Bulk 35AM2 - Bulk 35ARM2 - Bulk 35WM2 - Bulk
Voltage: 12-24 Volt 12-24 Volt 12-24 Volt 12-24 Volt
Cable: 40cm standard, 2 metre available 40cm standard, 2 metre available 40cm standard, 2 metre available 40cm standard, 2 metre available
Current: @13.8Volts (Red-0.12Amps) (Amber-0.10Amps) (Amber/Red-0.10Amps) (White-0.05Amps) @28Volts (Red-0.07Amps) (Amber-0.07Amps) (Amber/Red-0.07Amps) (White-0.04Amps)
CRn#: (Rear Position 34007) (Side Direction Indicator 33894) (Side marker 34099) (Front position 34008)
Fitting: Surface mount bracket onto flat surface horizontally to the ground with screws provided, run wires through back and clip lens into place. Please refer to ADR 13/00 for mounting instructions.
• 35RM• 35RMB• 35RM2• Rear end outline marker
• 35CRM• 35CRMB• Rear end outline marker
• 35AM• 35AMB• 35AM2• Side direction indicator
• 35CAM• 35CAMB• Side direction indicator
• 35ARM• 35ARMB• 35ARM2• Side marker
• 35CARM• 35CARMB• Side marker
Marker Lamps - 58mm x 35mm x 21mm
21mm
35mm
58mm
ADR/ECE approved
5
YEAR WARRAnTY Chrome Chrome Chrome Chrome
Marker Lamps - 70mm x 35mm x 20mm ADR/ECE approved
5
YEAR WARRAnTY
Product Description:
The 36 series marker lamps are fully submersible, shock resistant with a brand new shape and design. These lamps come with push in brush clips and quality 3M tape, only 3 holes required to be drilled in fixing surface and no need for any screws.
Part no 36RM 36CRM 36AM 36CAM 36ARM 36CARM 36WM 36CWM
Voltage: 12-24 Volt 12-24 Volt 12-24 Volt 12-24 Volt 12-24 Volt 12-24 Volt 12-24 Volt 12-24 Volt
Cable: 16cm 16cm 16cm 16cm 16cm 16cm 16cm 16cm
Packaging: Blister of 1 Blister of 1 Blister of 1 Blister of 1 Blister of 1 Blister of 1 Blister of 1 Blister of 1
Current: @13.8Volts (Red-TBA Amps) (Amber-TBA Amps) (Amber/Red-TBA Amps) (White-TBA Amps) @28Volts (Red-TBA Amps) (Amber-TBA Amps) (Amber/Red-TBA Amps) (White-TBA Amps)
C.R.n: (Rear Position TBA) (Side Direction Indicator TBA) (Side marker TBA) (Front position TBA)
Fitting: Surface mount onto flat surface horizontally to the ground, drill two 6mm holes for brush clips and one 8 mm hole for wire. Ensure 3M tape is fitted before running wires through back and clip lens into place. Please refer to ADR 13/00 for mounting instructions.
• 36WM• Front end outline
• 36CWM• Front end outline
• 36RM• Rear end outline
• 36CRM• Rear end outline
• 36AM• Side direction indicator
• 36CAM• Side direction indicator
• 36ARM• Side marker
• 36CARM• Side marker
35mm
30mm20mm
70mm
Innovative new push in brush clip for mounting, with added 3M tape for security.
nEW
PRODUCT nEW
PRODUCT nEW
PRODUCT nEW
PRODUCT
45Information Correct at time of printing
Description: The 58 series lamps are water proof, shock resistant with a slimline design. Individual clip in lenses allow easy surface mount with no visible screws.
Part no,Packaging
58RM - Blister 58AM - Blister 58ARM - Blister 58WM - Blister
58RMB - Bulk box of 10 58AMB - Bulk box of 10 58ARMB - Bulk box of 10 58WMB - Bulk box of 10
58CRM - Blister 58CAM - Blister 58CARM - Blister 58CWM - Blister
58CRMB - Bulk box of 10 58CAMB - Bulk box of 10 58CARMB - Bulk box of 10 58CWMB - Bulk box of 10
58RM3 - Bulk 58AM3 - Bulk 58ARM3 - Bulk 58WM3 - Bulk
58CRM3 - Bulk 58CAM3 - Bulk 58CARM3 - Bulk 58CWM3 - Bulk
Voltage: 12-24 Volt 12-24 Volt 12-24 Volt 12-24 Volt
Cable: 40cm standard, 3 metre available 40cm standard, 3 metre available 40cm standard, 3 metre available 40cm standard, 3 metre available
Current: @13.8Volts (Red-0.12Amps) (Amber-0.10Amps) (Amber/Red-0.10Amps) (White-0.05Amps) @28Volts (Red-0.04Amps) (Amber-0.04Amps) (Amber/Red-0.040Amps) (White-0.03Amps)
CRn#: (Rear Position 36840) (Side Direction Indicator 38277) (Side marker 36841) (Front position 36842)
Fitting: Surface mount bracket onto flat surface horizontally to the ground with screws provided, run wires through back and clip lens into place. Please refer to ADR 13/00 for mounting instructions.
• 58WM• 58WMB• 58WM3• Front end outline
• 58CWM• 58CWMB• 58CWM3• Front end outline
• 58RM• 58RMB• 58RM3• Rear end outline
• 58CRM• 58CRMB• 58CRM3• Rear end outline
• 58AM• 58AMB• 58AM3• Side direction indicator
• 58CAM• 58CAMB• 58CAM3• Side direction indicator
• 58ARM• 58ARMB• 58ARM3• Side marker
• 58CWM• 58CWMB• 58CWM3• Side marker
Marker Lamps - 58mm x 35mm x 21mm
21mm
35mm
58mm
ADR/ECE approved
5
YEAR WARRAnTY
Chrome Chrome Chrome Chrome
Product Description:
The 42 series marker lamps are fully submersible, shock resistant with a classic shape and design. Individual clip in lenses allow easy surface mount or retro fit, with no visible screws.
Part no 42RMB 42CRMB 42AMB 42CAMB 42ARMB 42CARMB 42WMB 42CWMB
Voltage: 12-24 Volt 12-24 Volt 12-24 Volt 12-24 Volt 12-24 Volt 12-24 Volt 12-24 Volt 12-24 Volt
Cable: 16cm 16cm 16cm 16cm 16cm 16cm 16cm 16cm
Packaging: Box of 10 Box of 10 Box of 10 Box of 10 Box of 10 Box of 10 Box of 10 Box of 10
Current: @13.8Volts (Red-0.05Amps) (Amber-0.05Amps) (Amber/Red-0.05Amps) (White-0.03Amps) @28Volts (Red-0.06Amps) (Amber-0.06Amps) (Amber/Red-0.06Amps) (White-0.03Amps)
C.R.n: (Rear Position 42839) (Side Direction Indicator 42836) (Side marker 42837) (Front position 42840)
Fitting: Surface mount bracket onto flat surface horizontally to the ground with screws provided, run wires through back and clip lens into place. Please refer to ADR 13/00 for mounting instructions.
• 42WMB• Front end outline
• 42CWMB• Front end outline
• 42RMB• Rear end outline
• 42CRMB• Rear end outline
• 42AMB• Side direction indicator
• 42CAMB• Side direction indicator
• 42ARMB• Side marker
• 42CARMB• Side marker
Marker Lamps - 74mm x 38mm x 35mm
35mm
38mm
74mm
ADR/ECE approved
5
YEAR WARRAnTY Chrome Chrome Chrome Chrome
nEW
PRODUCT nEW
PRODUCT nEW
PRODUCT nEW
PRODUCT
46 Information Correct at time of printing
Product Description:
The 38 series marker lamps are fully submersible, shock resistant, feature our hexagonal lens pattern, and have a slimline design with reflex reflector. Clip on chrome bezel allow easy surface mount with no visible screws. Various other coloured brackets also available.
Part no 38CRM 38CAM 38CARM 38CARMB 38CWM
Voltage: 12-24 Volt 12-24 Volt 12-24 Volt 12-24 Volt 12-24 Volt
Cable: 40cm 40cm 40cm 40cm 40cm
Packaging: Blister of 1 Blister of 1 Blister of 1 Poly bag of 1 Blister of 1
Current: @13.8Volts (Red-0.05Amps) (Amber-0.06Amps) (Amber/Red-0.06Amps) (White-0.05Amps) @28Volts (Red-0.06Amps) (Amber-0.06Amps) (Amber/Red-0.06Amps) (White-0.05Amps)
C.R.n: (Rear Position 40352) (Side Direction Indicator 40377) (AM - Side marker 40385) (Side marker 40302) (Front position 40353) (Reflector 38101, 38102, 38103)
Fitting: Surface mount lamp onto flat surface horizontally to the ground with screws provided, run wires through back and clip bezel into place. Please refer to ADR 13/00 for mounting instructions.
• 38CRM• Rear end outline marker with reflector
• 38CARM• 38CARMB• Side marker with reflector
• 38CAM• Side direction indicator with reflector
• 38CWM• Front end outline marker with reflector
Product Description:
The 38 series marker lamps are fully submersible, shock resistant, feature our hexagonal lens pattern, and have a slimline design with reflex reflector. Clip on bezel allow easy surface mount with no visible screws. Various coloured brackets available.
Part no 38RM 38RMB 38AM 38AMB 38ARM 38ARMB 38WM 38WMB
Voltage: 12-24 Volt 12-24 Volt 12-24 Volt 12-24 Volt 12-24 Volt 12-24 Volt 12-24 Volt 12-24 Volt
Cable: 40cm 40cm 40cm 40cm 40cm 40cm 40cm 40cm
Packaging: Blister of 1 Poly bag of 1 Blister of 1 Poly bag of 1 Blister of 1 Poly bag of 1 Blister of 1 Poly bag of 1
Current: @13.8Volts (Red-0.05Amps) (Amber-0.06Amps) (Amber/Red-0.06Amps) (White-0.05Amps) @28Volts (Red-0.06Amps) (Amber-0.06Amps) (Amber/Red-0.06Amps) (White-0.05Amps)
C.R.n: (Rear Position 40352) (Side Direction Indicator 40377) (AM - Side marker 40385) (Side marker 40302) (Front position 40353) (Reflector 38101, 38102, 38103)
Fitting: Surface mount lamp onto flat surface horizontally to the ground with screws provided, run wires through back and clip bezel into place. Please refer to ADR 13/00 for mounting instructions.
• 38RM• 38RMB• Rear end outline marker with reflector
• 38ARM• 38ARMB• Side marker with reflector
• 38AM• 38AMB• Side direction indicator with reflector
• 38WM• 38WMB• Front end outline marker with reflector
Marker Lamps with inbuilt reflector 135mm x 38mm x 22mm
chrome Marker Lamps with inbuilt reflector 135mm x 38mm x 22mm
• 38 series coloured brackets available
22mm
38mm
135mm
22mm
38mm
135mm
ADR/ECE approved
ADR/ECE approved
5
YEAR WARRAnTY
5
YEAR WARRAnTY
47Information Correct at time of printing
Product Description:
The 38 series marker lamps are fully submersible, shock resistant and feature our hexagonal lens pattern. Slimline design with reflex reflector. Clip on bezel allow easy surface mount with no visible screws.
Part no 38RMBKT 38AMBKT 38ARMBKT 38ARMBKTR 38WMBKT
Voltage: 12-24 Volt 12-24 Volt 12-24 Volt 12-24 Volt 12-24 Volt
Cable: 40cm 40cm 40cm 40cm 40cm
Packaging: Blister of 1 Blister of 1 Blister of 1 Blister of 1 Right side Poly bag of 1
Current: @13.8Volts (Red-0.05Amps) (Amber-0.06Amps) (Amber/Red-0.06Amps) (White-0.05Amps) @28Volts (Red-0.06Amps) (Amber-0.06Amps) (Amber/Red-0.06Amps) (White-0.05Amps)
C.R.n: (Rear Position 40352) (Side Direction Indicator 40377) (AM - Side marker 40385) (Side marker 40302) (Front position 40353) (Reflector 38101, 38102, 38103)
Fitting: Mount lamp onto flat surface horizontally to the ground with 90° bracket and screws provided, run wires at back through middle hole in bracket. Please refer to ADR 13/00 for mounting instructions.
• 38RMBKT• Rear end outline marker with reflector
• 38ARMBKT • 38ARMBKTR• Side marker with reflector
• 38AMBKT• Side direction indicator with reflector
• 38WMBKT• Front end outline marker with reflector
Marker Lamps with right Angle Bracket160mm x 62mm x 42mm
42mm
38mm
160mm
135mm
62mm
• 38 series coloured brackets available
ADR/ECE approved
5
YEAR WARRAnTY
• Front end outline marker with reflector• 38WMBKT
Product Description:
The 38 series marker lamps are fully submersible, shock resistant and feature our hexagonal lens pattern. Slimline design with reflex reflector. Clip on bezel allow easy surface mount with no visible screws.
Part no 38RMMB 38AMMB 38ARMMB 38WMMB
Voltage: 12-24 Volt 12-24 Volt 12-24 Volt 12-24 Volt
Cable: 40cm 40cm 40cm 40cm
Packaging: Poly bag of 1 Poly bag of 1 Poly bag of 1 Poly bag of 1
Current: @13.8Volts (Red-0.05Amps) (Amber-0.06Amps) (Amber/Red-0.06Amps) (White-0.05Amps) @28Volts (Red-0.06Amps) (Amber-0.06Amps) (Amber/Red-0.06Amps) (White-0.05Amps)
C.R.n: (Rear Position 40352) (Side Direction Indicator 40377) (AM - Side marker 40385) (Side marker 40302) (Front position 40353) (Reflector 38101, 38102, 38103)
Fitting: Mount onto flat metal surface with magnetic base, run wires through back. Please refer to ADR 13/00 for mounting instructions.
• 38RMMB• Rear end outline marker with reflector
• 38ARMMB• Side marker with reflector
• 38AMMB• Side direction indicator with reflector
• 38WMMB• Front end outline marker with reflector
Magnetic Marker Lamps135mm x 38mm x 29mm
29mm
38mm
135mm
ADR/ECE approved
5
YEAR WARRAnTY
Back view
Side view showing magnets and grommet separated
48 Information Correct at time of printing
Product Description: These marker lamps are an easy one piece fit with a low profile and including a reflex reflector in the assembly.
Part no 44RME 44WRME 44AME 44AMEB 44WAME 44WME 44WWME
Voltage: 12-24 volt 12-24 volt 12-24 volt 12-24 volt 12-24 volt 12-24 volt 12-24 volt
Cable: 50cm 50cm 50cm 50cm 50cm 50cm 50cm
Packaging: Blister of 1 Blister of 1 Blister of 1 Poly bag Blister of 1 Blister of 1 Blister of 1
Current: @13.8Volts (Marker-0.02 Amps) @28Volts (Marker-0.03 Amps)
C.R.n: R1-E9-02 (Rear Position Component number 6282) E900SM1 (Side marker Component number 1331) A-E9-02(Front position Component number 6283)
Fitting: Surface mount onto flat surface horizontally with screws, run wire through hole in fixing surface. Please refer to ADR 13/00 for mounting instructions.
slimline Marker Lamps - 100mm x 44mm x 12mm
12mm
44mm
100mm
• 1490RM• Rear end outline marker
• 1491RM• Rear end outline marker
• 1490AM• Side marker
• 1491AM• Side marker
• 1490WM• Front end outline marker
• 1491WM• Front end outline marker
Product Description:
The 1490/1491 series marker lamps are fully submersible, shock resistant and have a built in reflector. There are two fitting options available, flat surface or 90° bracket .These lamps are E.C.E and E mark approved.
Part no 1490RM 1490AM 1490WM
Voltage: 12-24 Volt 12-24 Volt 12-24 Volt
Cable: 20cm 20cm 20cm
Current: @13.8Volts (Red-0.05Amps) (Amber-0.05Amps) (White-0.05Amps) - @28Volts (Red-0.07Amps) (Amber-0.07Amps) (White-0.04Amps)
C.R.n: E9 00 SM1 02 1A (Rear Position Component number 1357) (Side marker Component number 1354) (Front position Component number 1358)
Fitting: Mount lamp onto flat surface horizontally to the ground, 1490 remove lens from base and fix with screws provided, and for 1491 with 90° bracket and screws provided. Please refer to ADR 13/00 for mounting instructions.
Product Description:
The 1490/1491 series marker lamps are fully submersible, shock resistant and have a built in reflector. There are two fitting options available, flat surface or 90° bracket .These lamps are E.C.E and E mark approved.
Part no 1491RM 1491AM 1491WM
Voltage: 12-24 Volt 12-24 Volt 12-24 Volt
Cable: 20cm 20cm 20cm
Current: @13.8Volts (Red-0.05Amps) (Amber-0.05Amps) (White-0.05Amps) - @28Volts (Red-0.07Amps) (Amber-0.07Amps) (White-0.04Amps)
C.R.n: E9 00 SM1 02 1A (Rear Position Component number 1357) (Side marker Component number 1354) (Front position Component number 1358)
Fitting: Mount lamp onto flat surface horizontally to the ground, 1490 remove lens from base and fix with screws provided, and for 1491 with 90° bracket and screws provided. Please refer to ADR 13/00 for mounting instructions.
Marker Lamps - 110mm x 40mm x 25mm
Marker Lamps with Bracket 110mm x 64mm x 25mm
40mm
25mm
110mm
47mm
25mm
64mm
110mm
ECE approved
ECE approved
WARRAnTY
5
YEAR
WARRAnTY
5
YEAR
WARRAnTY
5
YEAR
ECE approved
• 44RME • Rear end outline marker with Reflector
• 44WRME • Rear end outline marker with Reflector
• 44AME • 44AMEB• Side marker with Reflector
• 44WAME • Side marker with Reflector
• 44WME • Front end outline marker with Reflector
• 44WWME • Front end outline marker with Reflector
nEW
PRODUCT nEW
PRODUCT nEW
PRODUCT
49Information Correct at time of printing
Marker Lamps - 105mm x 31mm x 30mm
Marker Lamps - 74mm x 38mm x 25mm
• 1474R • 1474A • 1474W • 12612 • 12611
25mm
38mm
31mm
30mm
74mm
105mm
25mm
38mm
31mm
30mm
74mm
105mm
• 1440R • 1440W
Product Description: These marker lamps are fully submersible and shock resistant, with chrome. Perfect for the budget conscious consumer.
Part no 1440R 1440A 1440W
Voltage: 12 Volt 12 Volt 12 Volt
Cable: 10cm 10cm 10cm
Current: @13.8Volts (Red-0.04Amps) (Amber-0.03Amps) (White-0.03Amps)
Fitting: Remove screws from front of lens, run wires through rubber grommet and 23mm hole in fixing surface. Place bracket horizontal to ground and fix with self tapping screw in assembly, ensure “TOP” is at the top, and then refix lens into place with screws.
• 1440A
Marker Lamps - 96mm x 58mm x 49mm
49mm
58mm
96mm
Clear lens red LEDs Clear lens amber LEDs
• 1388R • 1388A
• 1374R • 1374A
• 1388W
Product Description:
These marker lamps are fully submersible and shock resistant. Coloured lens with coloured LED’s or clear lens with coloured LED’s both with chrome bezel.
Part no 1388R 1388A 1388W 1374R 1374A
Voltage: 12 Volt 12 Volt 12 Volt 12 Volt 12 Volt
Cable: 20cm 20cm 20cm 20cm 20cm
Current: @13.8Volts (Red-0.07Amps) (Amber-0.12Amps) (White-0.24Amps)
Fitting: Remove bezel and surface mount lamp with screws provided, run wires through back and fit bezel over lamp.
Marker Lamps - 169mm x 55mm x 24mm
24mm
55mm
169mm
Product Description: These marker lamps are fully submersible and shock resistant, with chrome or black bases available separately.
Part no 1474R 1474A 1474W 1459R 1459A
Voltage: 12 Volt 12 Volt 12 Volt 12 Volt 12 Volt
Cable: 20cm 20cm 20cm 20cm 20cm
Current: @13.8Volts (Red-0.04Amps) (Amber-0.04Amps) (White-0.04Amps) @13.8Volts (Red-0.05Amps) (Amber-0.06Amps)
Fitting: Fit base to fixing surface run wire through back of base and plug into positive outlet in back of lamp, push lamp into base with negative outlet slotting into female earth in base. Lamps require bases for fitting.
• 1459R • 1459A
25mm
38mm
31mm
30mm
74mm
105mm
25mm
38mm
31mm
30mm
74mm
105mm
• 12572 • 12571
DOT/SAEapproved
DOT/SAEapproved
DOT/SAEapproved
WARRAnTY
5
YEAR
WARRAnTY
5
YEAR
5 YEAR WARRAnTY
50 Information Correct at time of printing
• 1284R• Rear end outline marker
• 1685AM• 1685AB• Rear end outline marker
• 1458WM• Front end outline marker
• 1458ARM• Side marker
Product Description:
The 1458 series marker lamps are designed for the budget conscious consumer, fully submersible and shock resistant. Individual clip in lenses allow easy surface mount with no visible screws. Available in single bulk packs.
Part no 1458RM 1458AM 1458ARM 1458WM
Voltage: 12-24 Volt 12-24 Volt 12-24 Volt 12-24 Volt
Cable: 20cm 20cm 20cm 20cm
Current: @13.8Volts (Red-0.06Amps) (Amber-0.06Amps) (Amber/Red-0.06Amps) (White-0.03Amps) @28Volts (Red-0.05Amps) (Amber-0.05Amps) (Amber/Red-0.05Amps) (White-0.04Amps)
C.R.n: (Rear Position 39437) (Side Direction Indicator 39436) (Side marker 39468) (Front position 39438)
Fitting: Surface mount bracket onto flat surface horizontally to the ground with screws provided, run wires through back and clip lens into place please refer to ADR 13/00 for mounting instructions.
• 1458RM• Rear end outline marker
• 1458AM• Side direction indicator
Product Description: The 1685 and the 1284 series marker lamps are fully submersible and shock resistant. Slimline design with reflex reflector.
Part no 1685RB 1685AM 1685AB 1284R 1284A
Voltage: 12-24 Volt 12-24 Volt 12-24 Volt 12 Volt 12 Volt
Cable: 29cm 29cm 29cm 15cm 15cm
Packaging: Poly bag of 1 Blister of 1 Poly bag of 1 Poly bag of 1 Poly bag of 1
Current: @13.8Volts (Red-0.05Amps) (Amber-0.05Amps) 1685AM only @28Volts (Amber-0.04Amps)
C.R.n: (1685AM Side Marker 39221) (1685AM Reflector 39222)
Fitting: Surface mount lamp onto flat surface horizontally to the ground with screws provided, run wires through back, please refer to ADR 13/00.
• 1685RB• Rear end outline marker
• 1284A• Rear end outline marker
Marker Lamps - 74mm x 38mm x 26mm
Marker Lamps - 152mm x 52mm x 29mm
Marker Lamps - 149mm x 52mm x 35mm
38mm
26mm
74mm
38mm
26mm
74mm
• 1458BC
52mm
29mm
35mm
152mm
52mm
149mm
52mm
29mm
35mm
152mm
52mm
149mm
Description: The 1282 and the1369 series marker lamps are fully submersible and shock resistant. Slimline design. Perfect for the budget conscious consumer.
Part no 1282R 1282A 1369R 1369A
Voltage: 12 Volt 12 Volt 12 Volt 12 Volt
Cable: 13cm 13cm 16cm hard wired with round connectors
Current: @13.8Volts (Red-0.06Amps) (Amber-0.05Amps) @13.8Volts (Red-0.05Amps) (Amber-0.05Amps)
Fitting: Remove lens from base and fit onto flat surface using single bolt supplied. Run wire through hole in base, refit lens into place.
Surface mount lamp with screws, run wires at back of lamp through hole in mounting surface.
• 1282R• Red marker
• 1282A• Amber marker
• 1369R• Red marker
• 1369A• Amber marker
Marker Lamps - 79mm x 51mm x 24mm
Marker Lamps - 102mm x 19mm x 35mm
24mm
51mm
19mm
35mm
79mm
102mm
76mm
24mm
51mm
19mm
35mm
79mm
102mm
76mm
ADR approved
ADR (amber) DOT/SAE approved
DOT/SAE approved
DOT/SAE approved
WARRAnTY
5
YEAR
WARRAnTY
5
YEAR
WARRAnTY
5
YEAR
51Information Correct at time of printing
• 1477R• Red marker
• 1477A• Amber marker
Product Description:
These extremely low profile marker lamps are water proof, shock resistant and have a tough rubber housing with sheathed cable for added protection. They are perfect for small tight spaces.
Part no 181RME 181AME 181WME
Voltage: 12-24 Volt 12-24 Volt 12-24 Volt
Cable: 20cm 20cm 20cm
Packaging: Blister pack of 1 Blister pack of 1 Blister pack of 1
Current: @13.8Volts (Red-0.03Amps) (Amber-0.03Amps) (White-0.03Amps)
C.R.n: ADR compliant under ECE approval (02R1 E9 CRN 6257) (00SM1 E9 CRN 1005) (02A E9 CRN 6258)
Fitting: Mount onto flat surface and push lamp and rubber housing into cutout (20mm in diameter) in mounting surface. Please refer to ADR13/00.
• 181RME• Red marker
• 181AME• Amber marker
• 181WME• White marker
Marker Lamps - 28mm Diameter x 25mm high
25mm
28mm
20mm
25mm
28mm
20mm
Marker Lamps - 71mm Diam x 17mm high, 94mm Diam x 19mm high
Product Description: These marker lamps are fully submersible, shock resistant and are suited for the budget conscious consumer.
Part no 1477R 1477A 1479R 1479A
Voltage: 12 Volt 12 Volt 12 Volt 12 Volt
Cable: Use Part number 3591 Use Part number 3591 Use Part number 3591 Use Part number 3591
Current: @13.8Volts (Red-0.04Amps) (Amber-0.05Amps)
Fitting: Fit grommet into cut out in fixing surface, run wires through back and plug into back of lamp, push lamp into grommet.
• 1479R• Red marker
• 1479A• Amber marker
17mm
19mm
58mm
76mm
94mm
71mm
17mm
19mm
58mm
76mm
94mm
71mm
17mm
19mm
58mm
76mm
94mm
71mm
17mm
19mm
58mm
76mm
94mm
71mm
• 12761
17mm
19mm
58mm
76mm
94mm
71mm
17mm
19mm
58mm
76mm
94mm
71mm
• 12781
• 3591
DOT/SAE approved
WARRAnTY
5
YEAR
WARRAnTY
5
YEAR
nEW
PRODUCT nEW
PRODUCT nEW
PRODUCT
ECE approved
rubber Marker Lamps - 193mm x 169mm x 66mmrubber Marker Lamps - 101mm x 82mm x 66mm
Product Description: These marker lamps are fully submersible, shock resistant and are suited for the budget conscious consumer.
Part no 1004R 1004L 1004RE 1004LE 1004ARM 1005WRM
Voltage: 12-24 Volt 12-24 Volt 12-24 Volt 12-24 Volt 12-24 Volt 12-24 Volt
Cable: 40cm from lens 40cm from lens 40cm from lens 40cm from lens 40cm 40cm
Current: @13.8Volts (Red-0.03Amps) (Amber-0.06Amps) (White - 0.02) - @28Volts (Red-0.04Amps) (Amber-0.06Amps) (white-0.03)
C.R.n: TBA TBA (Red 02 R1 E4 7895) (White 02A E4 7895) 43129 (Red 02 R1 E4 7895)
Fitting: Fix to flat surface, amber facing forward and red facing to the back with two bolts supplied.
• 1004R• 1004L• Side marker
• 1004RE• 1004LE• Side marker
• 1004ARM• Side marker
• 1005WRM• Side marker
193mm
66mm
82mm
169mm 66mm
101mm
69mm
WARRAnTY
5
YEAR
ADR/ECE approved
Cut out
Cut out
Cut out
52 Information Correct at time of printing
Product Description:
The 30 series (6434) licence plate lamps are fully submersible, shock resistant and are suited for the budget conscious consumer. Can also be used for general illumination.
Illumination lamp, can be used as a courtesy lamp.
Part no 30BLM 6434BWM 30CLM 6434CWM 65362
Voltage: 12-24 Volt 12-24 Volt 12-24 Volt 12-24 Volt 12 Volt
Cable: 14cm 14cm 14cm 14cm 40cm hard wired
Packaging: Blister pack of 2 Poly bag of 1 Blister pack of 2 Poly bag of 1 Poly bag of 1
Current: @13.8Volts (Licence-0.02Amps) - @28Volts (Licence-0.03Amps) @13.8Volts (0.11Amps)
C.R.n: (Licence plate lamps 40511) N/A
Fitting: Run wires through hole in flat fitting surface, ensure foam gasket is between lamp and surface, fix using screws sup-plied. You will require one lamp on the left and right side of the licence plate. Please refer to ADR 13/00.
Fit onto flat surface using bolts in assembly.
• 65362 No ADR
Licence plate Lamps - 65mm x 30mm x 24mm, 69mm x 54mm x 40mm
54mm
30mm
24mm
40mm
65mm
69mm
54mm
30mm
24mm
40mm
65mm
69mm
54mm
30mm
24mm
40mm
65mm
69mm
54mm
30mm
24mm
40mm
65mm
69mm
• 30CLM• 6434CWM
• 30BLM• 6434BWM
ADR/ECE approved
DOT/SAEapproved
WARRAnTY
5
YEAR
Product Description:
The 35 series licence plate lamps are fully submersible and shock proof. Also available with 6 metres of hard wired cable or with 1 metre ending in a plug which clips into the back of the 100, 150 and 275 series Generation II lamps.
Part no 35BLM 35BLMB 35CLM 35CLMB 35BLM1P 35BLM6
Voltage: 12-24 Volt 12-24 Volt 12-24 Volt 12-24 Volt 12-24 Volt 12-24 Volt
Cable: 40cm 40cm 40cm 40cm 1 Metre with plug 6 Metre no plug
Packaging: Blister of 1 Poly Bag of 1 Blister of 1 Poly Bag of 1 Blister of 1 Poly Bag of 1
Current: @13.8Volts (Licence-0.04Amps) - @28Volts (Licence-0.04Amps) .
C.R.n: (Licence 36280)
Fitting: Fit onto flat surface, 25mm from top centre, long edge of licence plate with lens facing towards the ground. Refer to ADR 13/00 for fitting instructions.
• 35BLM• 35BLMB • 35BLM1P • 1 metre of cable with plug • 35BLM6 • 6 metre of cable hard wire
Licence plate Lamps - 76mm x 42mm x 30mm
42mm
30mm
76mm
64mm
42mm
30mm
76mm
64mm
• 35CLM• 35CLMB
ADR/ECE approved
ADR/ECE approved
WARRAnTY
5
YEAR
LP1 with Sample of a Licence plate fitted, shown active.
Product Description:
The licence plate frame allows the licence plate to be fitted underneath the two licence plate lamps all in one housing. Comes with 1 metre of cable ending in a plug which clips into the back of the 100, 150 and 275 series Generation II lamps.
Part no LP1 LP1B
Voltage: 12-24 Volt 12-24 Volt
Cable: 1 metre 1 metre
Packaging: Blister of 1 Box of 1
Current: @13.8Volts (Licence-0.11Amps) - @28Volts (Licence-0.07Amps)
C.R.n: (Licence plate lamp 39611)
Fitting: Fixes into same screw pattern as standard Australian licence plate, then wire clips into back of Generation II lamp. Fit up to 1 metre away from lamps.
• LP1• LP1B
Licence plate Lamps - 375mm x 173mm x 25mm
173mm
25mm
375mmWARRAnTY
5
YEAR
53Information Correct at time of printing
Product Description:
The 52 series navigation lamps are fully submersible, shock resistant and comply with A.T.A.C standards. Slimline design. Removable backing plate allows easy surface mount with no visible screws.
Part no 52WW 52CW
Voltage: 12-24 Volt 12-24 Volt
Cable: 18cm Hard wired 18cm Hard wired
Packaging: Blister pack of 1 Blister pack of 1
Current: @13.8Volts (White-0.18Amps) - @28Volts (White-0.10Amps)
Fitting: Remove back plate with small screw driver and fix at two screw points with screws supplied, clip lamp and housing in place.
• 52WW• Stern/Towing Lamp
• 52CW• Stern/Towing Lamp
Marine navigation Lamps - 76mm x 52mm x 24mm
52mm
24mm
76mm
ATAC approved
WARRAnTY
5
YEAR
Product Description:
The 52 series navigation lamps are fully submersible, shock resistant and comply with A.T.A.C standards. Slimline design. Removable backing plate allow easy surface mount with no visible screws.
Part no 52WR 52CR 52WG 52CG
Voltage: 12-24 Volt 12-24 Volt 12-24 Volt 12-24 Volt
Cable: 18cm Hard wired 18cm Hard wired 18cm Hard wired 18cm Hard wired
Packaging: Blister pack of 1 Blister pack of 1 Blister pack of 1 Blister pack of 1
Current: @13.8Volts (Red-0.08Amps) (Green-0.12Amps) - @28Volts (Red-0.18Amps) (Green-0.20Amps)
Fitting: Remove back plate with small screw driver and fix at two screw points with screws supplied, clip lamp and housing in place.
• 52WR• Portside
• 52CR• Portside
• 52WG• Starboard
• 52CG• Starboard
Marine navigation Lamps - 76mm x 52mm x 25mm
52mm
25mm
76mm
ATAC approved
WARRAnTY
5
YEAR
WARRAnTY
5
YEAR
Product Description:
Dual colour marine lamp red and white. Red light night vision, no glare and non sensitive at night. Multi purpose applications in all areas where night vision is required when sensitivity to the eyes is important. With the coloured ambient light our night vision lamps are easy on the eye when coming from darkness. On/Off Switch for separate colours. Interior use only.
Part no 143RWW 143RWC
Voltage: 12 Volt 12 Volt
Cable: 40cm 40cm
Packaging: Blister of 1 Blister of 1
Illuminance: White @ 1 metre - TBA - Red @ 1 metre - TBA
Current: White @13.8Volts 0.33Amps - Red @13.8Volts 0.33Amps
Fitting: Remove bezel and surface mount using three screw points, run wires through hole in mounting surface and refit bezel by clicking into place.
• 143RWWActive White
• 143RWW Active Red
• 143RWCActive White
• 143RWCActive Red
Marine interior Lamps - 143mm Diameter x 40mm high
143mm
40mm
nEW
PRODUCT
nEW
PRODUCT
nEW
PRODUCT
nEW
PRODUCT
54 Information Correct at time of printing
Product Description:
These work lamps are waterproof and sea/salt spray resistant, with durable powder coated aluminium housing, and high impact acrylic lens. Powered by 5 high brightness 0.5 watt LED’s. Ideal for lighting rear of boats from rocket launchers.
Part no 7150BM - Black Housing 7150WM - White Housing
Voltage: 12-24 Volt 12-24 Volt
Cable: 30cm sheathed hard wired 30cm sheathed hard wired
Packaging: Blister hang/stand pack of 1 Blister hang/stand pack of 1
Illuminance: @ 1 metre - 300lx
Current: @13.8Volts 0.30Amps - @28Volts 0.19Amps
Fitting: Fix to mounting surface using stainless steel bolts and adjustable stainless steel bracket supplied.
• 7150BM 5 x 0.5 watt LEDs
• 7150WM 5 x 0.5 watt LEDs
30m 40m25m20m15m10m5m
2m
4m
6m
0
2m
4m
6m
Distance in Metres
Product Description:
These work lamps are waterproof and sea/salt spray resistant, with durable powder coated aluminium housing, and high impact acrylic lens. Powered by 9 high brightness 1 watt LED’s. Ideal for the rear of any vehicle needing intense illumination.
Part no 7790BM - Black Housing 7790WM - White Housing
Voltage: 12-24 Volt 12-24 Volt
Cable: 30cm sheathed hard wired 30cm sheathed hard wired
Packaging: Blister hang/stand pack of 1 Blister hang/stand pack of 1
Illuminance: @ 1 metre - 520lx
Current: @13.8Volts 0.97Amps - @28Volts 0.44Amps
Fitting: Fix to mounting surface using stainless steel bolts and adjustable stainless steel bracket supplied.
• 7790BM 9 x 1 watt LEDs
• 7790WM9 x 1 watt LEDs
Flood Lamps - 114mm x 48mm x 71mm
Flood Lamps - 169mm x 60mm x 77mm
48mm
114mm
71mm
60mm
169mm
77mm
5
YEAR WARRAnTY
5
YEAR WARRAnTY
2m
4m
0
2m
4m
30m 40m25m20m15m10m5mDistance in Metres
55Information Correct at time of printing
Product Description:
These work lamps are waterproof and sea/salt spray resistant, with durable powder coated aluminium housing, polycarbonate lens. Powered by 6 high brightness 1 watt LED’s.
Part no 7451BM - Black Housing 7451WM - White Housing
Voltage: 12-24 Volt 12-24 Volt
Cable: 30cm sheathed hard wired 30cm sheathed hard wired
Packaging: Blister hang/stand pack of 1 Blister hang/stand pack of 1
Illuminance: @ 1 metre - 3500lx
Current: @13.8Volts 0.75Amps - @28Volts 0.38Amps
Fitting: Fix to mounting surface using stainless steel bolt and bracket supplied.
• 7451BM 6 x 1 watt LEDs
• 7451WM 6 x 1 watt LEDs
Product Description:
These work lamps are waterproof and sea/salt spray resistant, with durable powder coated aluminium housing, polycarbonate lens and ABS adjustable or removable visor. Powered by 6 high brightness 1 watt LED’s.
Part no 7450B12- Black Housing 7450B24 - Black Housing 7450W12 - White Housing 7450W24 - White Housing
Voltage: 12 Volt 24 Volt 12 Volt 24 Volt
Cable: 30cm sheathed hard wired 30cm sheathed hard wired 30cm sheathed hard wired 30cm sheathed hard wired
Packaging: Blister hang/stand pack of 1 Blister hang/stand pack of 1 Blister hang/stand pack of 1 Blister hang/stand pack of 1
Illuminance: @ 1 metre - 2800lx
Current: @13.8Volts 1.29Amps - @28Volts 0.30Amps
Fitting: Fix to mounting surface using stainless steel bolt and bracket supplied.
• 7450B12• 7450B24 6 x 1 watt LEDs
• 7450W12• 7450W24 6 x 1 watt LEDs
Work Lamps - 150mm x 115mm x 41mm
Work Lamps - 158mm x 129mm x 90mm
30m 40m25m20m15m10m5m
2m
4m
6m
0
2m
4m
6m
Distance in Metres
92mm
41mm
115mm
150mm
30m 40m25m20m15m10m5m
2m
4m
0
2m
4m
Distance in Metres
158mm
129mm
90mm
5
YEAR WARRAnTY
5
YEAR WARRAnTY
56 Information Correct at time of printing
Work Lamps - 121mm x 110mm x 45mm
Work Lamps - 142mm x 115mm x 50mm
Work Lamps - 117mm x 88mm x 71mm
Work Lamps - 138mm x 114mm x 108mm
• 7220M 20 x 1 watt LEDs
• 7208MS 8 x 1 watt LEDs
• 7210M 10 x 1 watt LEDs
• 7208MR 8 x 1 watt LEDs
Product Description:
These work lamps are waterproof and sea/salt spray resistant, with durable powder coated aluminium housing, and polycarbonate lens. Powered by high brightness 1 watt LED’s. Packaged in a blister hang/stand pack.
Part no 7208MS 7208MR 7220M 7210M
Voltage: 12-24 Volt 12-24 Volt 12-24 Volt 12-24 Volt
Cable: 50cm sheathed hard wired 50cm sheathed hard wired 50cm sheathed hard wired 50cm sheathed hard wired
Illuminance: @ 1 metre - TBAlx @ 1 metre - TBAlx @ 1 metre - TBAlx @ 1 metre - TBAlx
Current: @13.8V 0.90Amps - @28V 0.44Amps @13.8V 1.05Amps - @28V 0.51Amps @13.8V 0.30Amps - @28V 1.15Amps @13.8V 0.67Amps - @28V 1.37Amps
Fitting: Fix to mounting surface using stainless steel bolts and adjustable stainless steel bracket supplied.
WARRAnTY
5
YEAR
WARRAnTY
5
YEAR
WARRAnTY
5
YEAR
WARRAnTY
5
YEAR
150m100m50m
10m20m30m
010m20m30m
Distance in Metres
70m 100m90m80m10m 20m 30m 40m 50m 60m
5m
5m
10m
10m
0
Distance in Metres
10m 60m20m 70m30m 80m40m 90m50m
5m
5m
10m
10m
0
Distance in Metres
150m100m50m
10m20m30m
010m20m30m
Distance in Metres
nEW
PRODUCT
nEW
PRODUCT
nEW
PRODUCT
nEW
PRODUCT
142mm
115mm 50mm
121mm
110mm 45mm
117mm
88mm 70mm
138mm
114mm 108mm
57Information Correct at time of printing
Product Description:
The 85 series work lamps are waterproof sea/salt spray resistant, and have a durable powder coated aluminium housing, stainless steel fittings, and high impact polycarbonate lens. Powered by high brightness 120° 1 watt LED’s.
Part no 856BM 858BM 8514BM
Voltage: 12-24 Volt 12-24 Volt 12-24 Volt
Cable: 1 metre sheathed hard wired 1 metre sheathed hard wired 1 metre sheathed hard wired
Packaging: Box of 1 Box of 1 Box of 1
Illuminance: @ 1 metre - 3715lx @ 1 metre - 4630lx @ 1 metre - 8460lx
Current: @13.8Volts 0.77Amps - @28Volts 0.36Amps @13.8Volts 1.00Amps - @28Volts 0.48Amps @13.8Volts 1.80Amps - @28Volts 0.78Amps
Fitting: Fix to mounting surface using stainless steel bolts and adjustable stainless steel bracket supplied.
• 8514BM 14 x 1 watt LEDs
• 858BM 8 x 1 watt LEDs
• 856BM 6 x 1 watt LEDs
heavy Duty Work Lamps - 170mm x 110mm x 86mm
heavy Duty Work Lamps - 208mm x 110mm x 86mm
heavy Duty Work Lamps - 321mm x 110mm x 86mm
30m 40m 50m20m10m
2m4m6m
02m4m6m
Distance in Metres
30m 40m 50m20m10m
2m4m6m
02m4m6m
Distance in Metres
30m 40m 50m20m10m
2m4m6m
02m4m6m
Distance in Metres
110mm
170mm 86mm
110mm40mm
110mm
208mm 86mm
110mm40mm
110mm
321mm 86mm
262mm116mm
5
YEAR WARRAnTY
5
YEAR WARRAnTY
5
YEAR WARRAnTY
nEW
PRODUCT
nEW
PRODUCT
nEW
PRODUCT
58 Information Correct at time of printing
w w w . l e d a u t o l a m p s . c o m P: 03 9464 5939 F: 03 9464 5940
Part No.: LWL8312WM
NEW PRODUCT 21/12/2011
Shining in the spotlight...
Description:
Voltage:
Cable:
Packaging:
Current:
Warranty:
Compact high powered work lamp.
10V-30V
50cm hard wired
Single blister hang pack
@13.8Volts (0.68Amps)@28Volts (0.36Amps)
3 Years
Part No.: LWL8312BM
10V-30V input voltage
High intensity 3W SMD LEDs
100% Water & dust proof IP67
3 year warranty
111m
m
65mm84mm
LED Technologies has a brand new edition to its powerful worklamp range. Introducing the all new 84mm round lamp with an aluminium cast casing and polycarbonate lens, this tough lamp is suitable for any heavy duty application. The lamp is IP67 rated and features 4 powerful 3 watt LEDs combined with a complex shape chrome reflector to provide the ultimate in lighting performance. Available in both black and white finishes, with a stainless steel bracket, this compact high performance lamp will suit any extreme application.
111m
m
65mm84mm
0
-5000mm2000mm 7000mm 12000mm 17000mm 22000mm
5000mm
59 Information Correct at time of printing
Product Description:
The 75 series white interior or exterior lamps have SMD LED’s, incredible high light output and 120° of light spread. The 75 series blue and red waterproof interior/exterior round lamps are available in blue light for daytime vision ideal for daylight use, or red light for night time vision. No glare & non sensitive when coming from darkness. High brightness SMD LED’s with polycarbonate lens.
Part no 7524W 7524G 7524C 7524/OPAQUE 7524* 7530W 7530G 7530C 7530/
OPAQUE 7530* 7524WB 7524WR
Voltage: 12 Volt 12 Volt 12 Volt 12 Volt 12 Volt 24 Volt 24 Volt 24 Volt 24 Volt 24 Volt 12 Volt 12 Volt
Cable: 40cm 40cm 40cm 40cm 40cm 40cm 40cm 40cm 40cm 40cm 40cm 40cm
Packaging: Blister of 1 Blister of 1 Blister of 1 Blister of 1 Bag of 1 Blister of 1 Blister of 1 Blister of 1 Blister of 1 Bag of 1 Blister of 1 Blister of 1
Illuminance: Clear lens 12 volt (@ 1 metre - 37lx) 24 volt (@ 1 metre - 50lx) Opaque lens 12 volt (@ 1 metre - 22lx) 24 volt (@ 1 metre - 28lx) @1mt-31lx @1mt-20lx
Current: @13.8Volts 0.24Amps - @28Volts 0.13Amps @13.8Volts Blue 0.20Amps, Red 0.15Amps
Fitting: Remove bezel and surface mount using three screw points, run wires through hole in mounting surface and refit bezel by clicking into place.
• 7524W• 7530W• Interior/Exterior
• 7524G• 7530G• Interior/Exterior
• 7524C• 7530C• Interior/Exterior
• 7524/OPAQUE• 7530/OPAQUE• Interior/Exterior
• 7524WB• Interior/Exterior• Blue & White LEDs
• 7524WR• Interior/Exterior• Red & White LEDs
75mm
17mm
* 7524 and 7530 supplied without bezel
3
YEAR WARRAnTY
Water proof Lamps - 75mm diameter x 17mm high
Product Description:
The 5100 series rectangular interior/exterior lamp are water resistant and will withstand high pressure washing. They are a recessed fit with 30 bright square LED’s.
Part no 5100W12 5100W24
Voltage: 12 Volt 24 Volt
Cable: N/A N/A
Packaging: Box of 1 Box of 1
Illuminance: @ 1 metre - TBA
Current: @13.8Volts 0.20Amps - @28Volts 0.10Amps
Fitting: Recess mount with 4 fixing points with screws into cutout (130mm x 87mm) in fixing surface. Attach wires to side of lamp.
• 5100W12 • 5100W24
recessed Exterior Lamps - 165mm x 102mm x 45mm
102mm
165mm
45mm
WARRAnTY
3
YEAR
60Information Correct at time of printing
• 143ILW12• 143ILW24• Interior Only
• 143ILC12• 143ILC24• Interior Only
• 143ILG12• 143ILG24• Interior Only
• 143ILB12• 143ILB24• Interior Only
Product Description: These lamps are interior or exterior, with white 120 SMD LED’s equivalent to a 50 watt globe and incredible high light output with 120° of light spread.
Part no 143120W12 143120G12 143120C12 143120B12 143120W24 143120G24 143120C24 143120B24
Voltage: 12 Volt 12 Volt 12 Volt 12 Volt 24 Volt 24 Volt 24 Volt 24 Volt
Cable: 40cm 40cm 40cm 40cm 40cm 40cm 40cm 40cm
Packaging: Blister of 1 Blister of 1 Blister of 1 Blister of 1 Blister of 1 Blister of 1 Blister of 1 Blister of 1
Illuminance: @ 1 metre - 86lx Current: @13.8Volts 0.46Amps - @28Volts 0.27Amps
Fitting: Remove bezel and surface mount using three screw points, run wires through hole in mounting surface and refit bezel by clicking into place.
• 143120G12• 143120G24• Interior/Exterior
• 143120B12• 143120B24• Interior/Exterior
• 143120W12• 143120W24• Interior/Exterior
• 143120C12• 143120C24• Interior/Exterior
Product Description:
These lamps are interior only and have an ON/DOOR/OFF switch. 120 white SMD LED’s equivalent to a 50 watt globe give incredible high light output with a 120° light spread.
Part no 143ILW12 143ILG12 143ILC12 143ILB12 143ILW24 143ILG24 143ILC24 143ILB24
Voltage: 12 Volt 12 Volt 12 Volt 12 Volt 24 Volt 24 Volt 24 Volt 24 Volt
Cable: 40cm 40cm 40cm 40cm 40cm 40cm 40cm 40cm
Packaging: Blister of 1 Blister of 1 Blister of 1 Blister of 1 Blister of 1 Blister of 1 Blister of 1 Blister of 1
Illuminance: @ 1 metre - 86lx Current: @13.8Volts 0.46Amps - @28Volts 0.27Amps
Fitting: Remove bezel and surface mount using three screw points, run wires through hole in mounting surface and refit bezel by clicking into place.
interior/Exterior Lamps - 143mm Diameter x 40mm high
interior Lamps with on/Door/off switch 143mm Diameter x 40mm high
143mm
40mm
143mm
40mm
3
YEAR WARRAnTY
3
YEAR WARRAnTY
61 Information Correct at time of printing
• 1016 • 1016/24• 100mm length
• 1031 • 1031/24• 150mm length
• 1061 • 1061/24• 300mm length
• 10121 • 10121/24• 600mm length
Product Description:
These lamps are interior only, using white SMD LED’s with high light output and a 120° light spread. Output equivalent to a 10 watt, 18 watt, 30 watt and 60 watt globe. Low profile design for small spaces, an unobtrusive yet stylish look.
Part no 1016 1031 1061 10121 1016/24 1031/24 1061/24 10121/24
Voltage: 12 Volt 12 Volt 12 Volt 12 Volt 24 Volt 24 Volt 24 Volt 24 Volt
Cable: 10cm 10cm 10cm 10cm 10cm 10cm 10cm 10cm
Packaging: Blister of 1 Blister of 1 Blister of 1 Blister of 1 Blister of 1 Blister of 1 Blister of 1 Blister of 1
Illuminance: @1metre - 18lx @1metre - 33lx @1metre - 62lx @1metre - 130lx @1metre - 18lx @1metre - 33lx @1metre - 62lx @1metre - 130lx
Current: @13.8V 0.11Amps @13.8V 0.17Amps @13.8V 0.31Amps @13.8V 0.58Amps @28V 0.05Amps @28V 0.07Amps @28V 0.17Amps @28V 0.31Amps
Fitting: Remove bezel at each end and surface mount using two screw points, run wires through hole in mounting surface and refit bezel by clicking into place.
Product Description:
These lamps are interior only, using white SMD LED’s with high light output and a 120° light spread. Output equivalent to a 8 watt, 15 watt, 25 watt and 50 watt globe. Low profile design for small spaces, and unobtrusive yet stylish look.
Part no 1016/OPAQUE 1031/OPAQUE 1061/OPAQUE 10121/OPAQUE 1016/24OPAQUE 1031/24OPAQUE 1061/24OPAQUE 10121/24/OPAQUE
Voltage: 12 Volt 12 Volt 12 Volt 12 Volt 24 Volt 24 Volt 24 Volt 24 Volt
Cable: 10cm 10cm 10cm 10cm 10cm 10cm 10cm 10cm
Packaging: Blister of 1 Blister of 1 Blister of 1 Blister of 1 Blister of 1 Blister of 1 Blister of 1 Blister of 1
Illuminance: @1metre - 10lx @1metre - 21lx @1metre - 40lx @1metre - 80lx @1metre - 10lx @1metre - 21lx @1metre - 40lx @1metre - 80lx
Current: @13.8V 0.11Amps @13.8V 0.17Amps @13.8V 0.31Amps @13.8V 0.58Amps @28V 0.05Amps @28V 0.07Amps @28V 0.17Amps @28V 0.31Amps
Fitting: Remove bezel at each end and surface mount using two screw points, run wires through hole in mounting surface and refit bezel by clicking into place.
interior Lamps - 4 Lengths Available
interior Lamps - 4 Lengths Available
100mm
300m
m
600m
m
150mm
25mm 10mm 10mm25mm
100mm
300m
m
600m
m
150mm
25mm 10mm 10mm25mm
3
YEAR WARRAnTY
3
YEAR WARRAnTY
• 1016/OPAQUE • 1016/24OPAQUE• 100mm length
• 1031/OPAQUE • 1031/24OPAQUE• 150mm length
• 1061/OPAQUE • 1061/24OPAQUE• 300mm length
• 10121/OPAQUE • 10121/24OPAQUE• 600mm length
62Information Correct at time of printing
Product Description: The 79 series interior lamp features a red night time illumination push button switch with high brightness SMD LED’s.
Part no 79BWR12 79GWR12 79CWR12 79SWR12 79WWR12
Voltage: 12 Volt 12 Volt 12 Volt 12 Volt 12 Volt
Cable: 20cm 20cm 20cm 20cm 20cm
Packaging: Blister of 1 Blister of 1 Blister of 1 Blister of 1 Blister of 1
Illuminance: @ 1 metre - 20lx
Current: OFF @13.8Volts 0.01Amps - ON @13.8Volts 0.09Amps
Fitting: Remove base by twisting until it is released from lamp and mount onto flat surface using three screw points. Run wires through hole in mounting surface and refit lamp by turning back into place.
• 79SWR12• Interior Only
• 79WWR12• Interior Only
• 79GWR12• Interior Only
• 79BWR12• Interior Only
• 79CWR12• Interior Only
interior Lamps with red illuminated on/off switch80mm Diameter x 14mm
80mm
14mm
3
YEAR WARRAnTY
Product Description:
The 148 series domed low profile rectangular interior lamp has a wide 120° light spread, with 24 bright white SMD LED’s. Out put equivalent to a 15 watt globe.
Part no 148BW12 148GW12 148WW12
Voltage: 12 Volt 12 Volt 12 Volt
Cable: 20cm 20cm 20cm
Packaging: Blister of 1 Blister of 1 Blister of 1
Illuminance: @ 1 metre - 42lx
Current: @13.8Volts 0.17Amps
Fitting: Remove lens from base, surface mount with 4 fixing points using screws supplied. Run wires through fixing surface from back of lamp. Refit lens.
• 148BW12• Interior Only
• 148GW12• Interior Only
• 148WW12• Interior Only
interior Lamps - 148mm x 71mm x 20mm
71mm
148mm
20mm
3
YEAR WARRAnTY
63 Information Correct at time of printing
w w w . l e d a u t o l a m p s . c o m P: 03 9464 5939 F: 03 9464 5940
NEW PRODUCT 30/11/2011
Cat 6 Side Direction Indicators
Description:
Voltage:Cable:Packaging:Current:
C.R.N:Fitting:
Warranty:
The 3102 series Category 6, side direction indicators are available in a chrome or black ABS/polycarbonate mounting bracket. They are fully sealed,water proof with tough ABS lens.9 Volt - 33 Volt19cmBox of [email protected] (0.20Amps) @28Volts (0.10Amps) E.C.E. 60 1 E4 - 61333Left or right hand mountable. Surface mount bracket onto flat surface horizontally to the ground using three screw points, run wires through back and clip lens into place. Please refer to ADR 13/00 for mounting instructions.5 Years
Part No.: 3102BM Part No.: 3102CM
150mm x 88mm x 30mm
150mm 30mm
88mm
30mm
64Information Correct at time of printing
Product Description:
The 380 series door entry interior/exterior lamps are fully sealed water proof. They have 18 high brightness LED’s with the lamp inside a 90 º low profile rounded housing. These lamps are perfect for caravans, trucks or RVs or any door entry application that requires lighting.
Part no 380WEL 380CEL
Voltage: 12 Volt 12 Volt
Cable: 40cm 40cm
Packaging: Blister of 1 Blister of 1
Illuminance: @ 1 metre - TBA
Current: @13.8Volts 0.14Amps
Fitting: Mount onto flat surface with screws, run wires through hole in fixing surface. Ensure screw plugs are fitted after fixing for a neat clean finish.
caravan Door Entry Lamps - 430mm x 35mm x 35mm
Lamps are shown in active mode
35mm
35mm
430mm
361mm
Product Description:
These hand held work lamps are powered by 61 high brightness SMD LED’s, encased in a protective oil resistant rubber housing with non slip handle and available with a 240 volt option or alligator clip for 12 volt applications.
Part no HH1061/12 HH1061/240
Voltage: 12 volt only 240 volt with transformer
Cable: 3 metres of sheathed wire with alligator clips 7 metres of sheathed wire with transformer
Packaging: Blister pack of 1 Blister pack of 1
Illuminance: @ 1 metre - 62lx
Current: @13.8Volts 0.31Amps
• HH1061/12• Hand Held Work Lamp
• HH1061/240• Hand Held Work Lamp
hand held Work Lamps - 424mm x 31mm
424mm
31mm
WARRAnTY
3
YEAR
WARRAnTY
3
YEAR
• 380WEL
• 380CEL
nEW
PRODUCT
nEW
PRODUCT
nEW
PRODUCT
nEW
PRODUCT
65 Information Correct at time of printing
Product Description:
The 35 series courtesy lamps are fully submersible, shock resistant and feature our hexagonal lens pattern. Slimline design. Individual clip in lenses for easy surface mount with no visible screws. Chrome and white brackets available separately.
Part no 35AM 35YM 35RM 35BM 35PM 35GM 35WM
Voltage: 12-24 Volt 12-24 Volt 12-24 Volt 12-24 Volt 12-24 Volt 12-24 Volt 12-24 Volt
Cable: 40cm 40cm 40cm 40cm 40cm 40cm 40cm
Packaging: Blister of 1 Blister of 1 Blister of 1 Blister of 1 Blister of 1 Blister of 1 Blister of 1
Warranty: 5 years 3 years 5 years 3 years 3 years 3 years 5 years
Illuminance: @1metre - 7.5lx @1metre - TBAlx @1metre - 10.4lx @1metre - 1.3lx @1metre - TBAlx @1metre - 0.6lx @1metre - 14.7lx
Current: @13.8Volts (Blue-0.04Amps) (Green-0.04Amps) (Red-0.12Amps) (Amber-0.10Amps) (White-0.05Amps) (Yellow-0.05Amps) (Purple-0.05Amps) @28Volts (Blue-0.02Amps) (Green-0.02Amps) (Red-0.07Amps) (Amber-0.07Amps) (White-0.04Amps) (Yellow-0.04Amps) (Purple-0.04Amps)
Fitting: Surface mount bracket with screws provided, run wires through back and clip lens into place.
• 35AM• Orange
• 35YM• Yellow
• 35RM• Red
• 35BM• Blue
• 35PM• Purple
• 35GM• Green
• 35WM• White
Product Description:
The 6505 series right angle interior or exterior step lamps feature coloured or opaque lens with 120° light spread and high brightness SMD LED’s. Protective chrome plated metal housing.
Part no 6505OM 6505YM 6505RM 6505BM 6505PM 6505GM 6505WM 6505IM
Voltage: 12-24 Volt 12-24 Volt 12-24 Volt 12-24 Volt 12-24 Volt 12-24 Volt 12-24 Volt 12-24 Volt
Cable: 30cm 30cm 30cm 30cm 30cm 30cm 30cm 30cm
Packaging: Blister of 1 Blister of 1 Blister of 1 Blister of 1 Blister of 1 Blister of 1 Blister of 1 Blister of 1
Illuminance: @1metre-3.52lx @1metre-4.8lx @1metre-1.10lx @1metre-1.37lx @1metre-1.00lx @1metre-1.77lx @1metre-4.46lx @1metre-2.6lx
Current: @13.8Volts 0.03Amps - @28Volts 0.04Amps
Fitting: Using screws supplied attach to surface and run wires at back through hole in mounting surface.
• 6505OM• Orange
• 6505YM• Yellow
• 6505BM• Blue
• 6505PM• Purple• 6505RM
• Red
• 6505GM• Green
• 6505WM• White
• 6505IM• Soft white
Water proof colour Lamps - 58mm x 35mm x 21mm
Water proof colour Lamps - 65mm x 30mm x 24mm
21mm
35mm
58mm
• 35BW
• 35BC
• 35BB
54mm
30mm
24mm
40mm
65mm
69mm
3
YEAR WARRAnTY
3
YEAR WARRAnTY
66Information Correct at time of printing
Product Description:
The 305 series interior only lamps feature 15 coloured SMD LED’s with coloured lenses. They are very low profile and only 15mm in width, perfect for tight small spaces where coloured lighting is required.
Part no 305A12 305R12 305B12 305G12 305W12
Voltage: 12 Volt 12 Volt 12 Volt 12 Volt 12 Volt
Product Description:
The 75 series coloured interior/exterior courtesy lamps feature 4 square LED’s with coloured diffused lens for maximum light output. Supplied with chrome bezel, white, black and gold bezels available separately.
Part no 75CLO 75CLY 75CLR 75CLB 75CLP 75CLG 75CLI
Voltage: 12 Volt 12 Volt 12 Volt 12 Volt 12 Volt 12 Volt 12 Volt
Cable: 40cm 40cm 40cm 40cm 40cm 40cm 40cm
Illuminance: @1metre-0.91 lx @1metre-1.55 lx @1metre-0.25 lx @1metre-0.09 lx @1metre-0.38 lx @1metre-0.82 lx @1metre-1.43 lx
Current: @13.8Volts 0.06Amps
Fitting: Remove bezel and surface mount using two screw points, run wires through hole in mounting surface and refit bezel by clicking into place.
• 75CLO• Orange
• 75CLY• Yellow
• 75CLR• Red
• 75CLB• Blue
• 75CLP• Purple
• 75CLG• Green
• 75CLI• White
Water proof colour Lamps - 75mm diameter x 17mm high
75mm
17mm
• 68O• Orange
• 68Y• Yellow
• 68R• Red
• 68G• Green
• 68W• White
• 68B• Blue
• 68P• Purple
• 68I• Soft white
Product Description: The 68 series coloured courtesy lamps are for interior use only, with high brightness SMD LED’s and a wide 120° light spread.
Part no 68O 68Y 68R 68B 68P 68G 68W 68I
Voltage: 12 Volt 12 Volt 12 Volt 12 Volt 12 Volt 12 Volt 12 Volt 12 Volt
Cable: 10cm 10cm 10cm 10cm 10cm 10cm 10cm 10cm
Illuminance: @1metre - 10lx @1metre - 13lx @1metre - 3lx @1metre - 3lx @1metre - 6lx @1metre - 11lx @1metre - 16lx @1metre - 10lx
Current @13.8V: 0.11Amps 0.17Amps 0.31Amps 0.58Amps 0.05Amps 0.11Amps 0.16Amps 0.10Amps
Fitting: Remove bezel at each end and surface mount using two screw points, run wires through hole in mounting surface and refit bezel by clicking into place.
colour Lamps - 100mm x 25mm x 10mm
25mm
10mm
100mm
WARRAnTY
WARRAnTY
3
YEAR
3
YEAR
• 305A12• Orange
• 305R12• Red
• 305B12• Blue
• 305G12• Green
• 305W12• White
colour Lamps - 305mm x 15mm x 7mm
305mm
15mm 7mm
nEW
PRODUCT
nEW
PRODUCT
nEW
PRODUCT
nEW
PRODUCT
nEW
PRODUCT
WARRAnTY
3
YEAR
67 Information Correct at time of printing
Products shown in active mode
Product Description:
These lamps are fully water proof, rust proof, shock resistant, dust proof and feature incredibly bright LED illumination with clear lens and coloured LEDs. Constructed with high impact polycarbonate lens and black powder coated aluminium housing with adjustable U bracket and stainless steel bolts and fittings. Comes standard with synchronising wire and up to 18 different strobe patterns.
Part no 94AM 94BM 94RM 94WM
Voltage: 12-24 Volt 12-24 Volt 12-24 Volt 12-24 Volt
Cable: 1 Metre hard wired 1 Metre hard wired 1 Metre hard wired 1 Metre hard wired
Current (Amps):
13.8Volts - 0.38 constant28Volts - 0.20 constant
13.8Volts - 0.50 constant28Volts - 0.26 constant
13.8Volts - 0.38 constant28Volts - 0.20 constant
13.8Volts - 0.50 constant28Volts - 0.27 constant
Fitting: Fix to mounting surface using adjustable U bracket, bolts and fittings supplied.
• 94AM • 94RM • 94BM Products shown in active mode
Emergency Lamps - 72mm x 72mm x 28mm
72mm
88mm
28mm72mm85mm
• 94WM
WARRAnTY
3
YEAR
Product Description:
The 93 series emergency lamps have 3 super bright high powered 1 watt coloured LED’s with two functions, strobe or constant. They also have extra functionality for synchronizing multiple lamps. Base is aluminium with polycarbonate lens and bezel. Fully sealed and water proof.
Part no 93AM 93RM 93BM 93GM 93WM
Voltage: 12-24 Volt 12-24 Volt 12-24 Volt 12-24 Volt 12-24 Volt
Cable: 19cm of hard wire 19cm of hard wire 19cm of hard wire 19cm of hard wire 19cm of hard wire
Flash Rate: 6 flashes every 0.3 seconds
Current: @13.8volt (Constant 0.24Amps), (Strobe 0.03-0.34Amps) - @28volt (Constant 0.07Amps), (Strobe 0.02-0.15Amps)
C.R.n ECE Approved
Fitting: Surface mount to flat surface with screws provided using flange and foam gasket.
25mm
36mm
93mm
25mm
36mm
93mm
Emergency Lamps - 93mm x 36mm x 25mm
• 93AM • 93BM• 93RM • 93WM• 93GM
• 50SAM • 50SGM• 50SBM• 50SRM • 50SWM
Emergency Lamps - 121mm x 49mm x 45mm
45mm
49mm
121mm
45mm
49mm
121mm
Product Description:
The 50 series emergency lamps use 4 super bright high powered LED’s with two functions, strobe or constant. Body is metal with polycarbonate lens. Fully sealed and water proof with 25cm of tinned copper wire.
Part no 50SAM 50SRM 50SBM 50SGM 50SWM
Voltage: 12-24 Volt 12-24 Volt 12-24 Volt 12-24 Volt 12-24 Volt
Cable: 25cm of hard wire 25cm of hard wire 25cm of hard wire 25cm of hard wire 25cm of hard wire
Packaging: Box of 1 Box of 1 Box of 1 Box of 1 Box of 1
Flash Rate: 6 flashes every 0.3 seconds
Current: @13.8volt (Constant 0.45Amps), (Strobe 0.03-0.26Amps) - @28volt (Constant 0.27Amps), (Strobe 0.03-0.16Amps)
Fitting: Fix to flat surface at two fixing points.
WARRAnTY
3
YEAR
WARRAnTY
3
YEAR
ECE approved
nEW
PRODUCT nEW
PRODUCT nEW
PRODUCT nEW
PRODUCT
68Information Correct at time of printing
Product Description:
Ultra low and compact high powered mini beacon, ideal for situations where low profile high intensity beacons are required. Intense 360 visibility with high impact polycarbonate lens with cast alloy base which acts as a heat sink. These beacons are shock resistant, vibration resistant and able to be fully submersed or high pressure washed. Reverse polarity protected with low power consumption. Easy fitting using only two fasteners supplied.
Part no MB12AM MB12AMC MBAME MBAMCE
Voltage: 10-110 volt 10-110 volt 10-110 volt 10-110 volt
Cable: 40cm of hard wire 40cm of hard wire 40cm of hard wire 40cm of hard wire
Packaging: Blister of 1 Blister of 1 Blister of 1 Blister of 1
Flash Rate: 45 flashes per minute 45 flashes per minute 120-240 flashes per minute 120-240 flashes per minute
Current: @13.8 volt (1.00 Amps) at peak, @28 volt (1.00 Amps) at peak
CRn: SAE J65 Class 1 SAE J65 Class 1 ECE R65 Approved ECE R65 Approved
Fitting: Fit to flat surface using screws at two fixing points supplied.
• MB12AM• MB12AMCSAE JU845 Class 112 x 1 watt LEDs45 Flash per minute10-110 volt
• Intense 360º visibility• High impact polycarbonate lens• Cast alloy base/heat distribution• Fully sealed and pre wired• Shock resistant• Vibration resistant• Water Proof• SAE J85 Class 1• ECE R65 approval• Wide voltage range 10-110v• Reverse polarity protected
• MB12AME• MB12AMCEECE R6512 x 1 watt LEDs120-240 Flash per minute10-110 volt
high powered Mini Beacon - 64mm high x 96mm wide
3
YEAR WARRAnTY
3
YEAR WARRAnTY
nEW
PRODUCT
AcTuAL
siZE
AcTuAL
siZE
nEW
PRODUCT
64mm
96mm
SAE J85 Class 1
ECE R65 approved
LED
TEcHnoLoGiEs
nEw DEsiGn
69 Information Correct at time of printing
strobe Beacons - 130mm x 98mm x 74mm
Product Description:
These small and robust units are available as a strobe type with 3 high powered Generation III LED’s and 45 flashes per minute. Fixed mount.
Part no 112ABM 112RBM
Voltage: 10 volt - 110 volt 10 volt - 110 volt
Cable: 34cm of hard wire 34cm of hard wire
Packaging: Blister of 1 Box of 1
Flash Rate: 45 flashes per minute
Current: @13.8 volt (0.13 Amps) at peak
Fitting: Mount to flat surface using foam gasket supplied, fitted between base and fixing surface using screws supplied.
• 112ABM• Fixed mount
• 112RBM• Fixed mount
130mm
98mm
3
YEAR WARRAnTY
• 111RM• Fixed mount
• 111AM• Fixed mount
• 111WM• Fixed mount
Product Description:
These small and robust units are available as a strobe type with 3 high powered Generation III LED’s and 45 flashes per minute. Fixed mount.
Part no 111RM 111AM 111WM
Voltage: 10 volt - 36volt 10 volt - 36volt 10 volt - 36volt
Cable: 34cm of hard wire 34cm of hard wire 34cm of hard wire
Packaging: Box of 1 Box of 1 Box of 1
Flash Rate: 45 flashes per minute
Current: @13.8 volt (0.13 Amps) at peak @13.8 volt (0.13 Amps) at peak @13.8 volt (0.13 Amps) at peak
Fitting: Mount to flat surface using foam gasket supplied, fitted between base and fixing surface using screws supplied.
strobe Beacons - 111mm high x 64mm diameter
111mm
58mm
64mm
3
YEAR WARRAnTY
nEW
PRODUCT nEW
PRODUCT nEW
PRODUCT
70Information Correct at time of printing
Product Description:
Mainly suited for indoor and factory/forklift use these compact and robust units are available only as a strobe with GNEII Super-LED and 60-70 triple flashes per minute. Two fixing options available, fixed mount with 40cm of hard wire (Not available for white beacon) or magnetic mount with 12 foot / 3.6 meter retractable cord ending in power source plug (only for the amber and white beacons).
Part no 127AMF 127AMM 127WMM 127RMF 127BMF 127GMF
Voltage: 12-24 volt 12-24 volt 12-24 volt 12-24 volt 12-24 volt 12-24 volt
Cable: 40cm of hard wire 12 foot/3.6mt retractable cord ending in power source plug 40cm of hard wire 40cm of hard wire 40cm of hard wire
Packaging: Box of 1 Box of 1 Box of 1 Box of 1 Box of 1 Box of 1
Flash Rate: 60-70 triple plashes per minute
Current: @13.8 volt (0.19 Amps) at peak, @28 volt (0.12 Amps) at peak
Fitting: Run wires through hole in fixing surface or from the side of the base. Attach with screws provided, ensure foam gasket is in place between lamp and fixing surface. 127AMM/127WMM - Place onto flat metal surface and run retractable cord to power source within vehicle.
• 127AMF• Fixed mount
• 127RMF• Fixed mount
• 127BMF• Fixed mount
• 127GMF• Fixed mount
• 127AMM• Magnetic mount
• 127WMM• Magnetic mount
strobe Beacons - 127mm x 97mm
97mm
127mm
3
YEAR WARRAnTY
Product Description:
These large and robust units are available as a strobe type with 12 high powered Generation III LED’s and 120-240 flashes per minute. Fixed mount.
Part no 182RM 182AM 182WM
Voltage: 10 volt - 36 volt 10 volt - 36 volt 10 volt - 36 volt
Cable: 34cm of hard wire 34cm of hard wire 34cm of hard wire
Packaging: Box of 1 Box of 1 Box of 1
Flash Rate: 120-240 flashes per minute
Current: @13.8 volt (0.26 Amps) at peak @13.8 volt (0.26 Amps) at peak @13.8 volt (0.13 Amps) at peak
Fitting: Mount to flat surface using foam gasket supplied, fitted between base and fixing surface using screws supplied.
• 182RM• Fixed mount
• 182AM• Fixed mount
• 182WM• Fixed mount
strobe Beacons - 182mm high x 125mm diameter
182mm
125mm
80mm
3
YEAR WARRAnTY
nEW
PRODUCT nEW
PRODUCT
nEW
PRODUCT
nEW
PRODUCTnEW
PRODUCTnEW
PRODUCT
nEW
PRODUCT
ECE R65 approved
71 Information Correct at time of printing
Product Description:
Powered by 48 super bright 30° LED’s with a centre brightness exceeding 700cd. One unit LED printed circuit board and housing combination with polycarbonate housing for strength and durability. The 3 bolt holes are the same dimensions as standard 4 inch arrow board shroud. The back of the lamp has provision for 4 inch “O” ring (supplied) for increased vibration resistance.
Part no 83R 83A 83G
Voltage: 12 volt only 12 volt only 12 volt only
Cable: 10cm Hard wired 10cm Hard wired 10cm Hard wired
Intensity: Centre brightness 700cd Centre brightness 700cd Centre brightness 700cd
Current: @ 13.8 volt (Red 0.42 Amps) (Amber 0.42 Amps) (Green 0.66 Amps)
Fitting: Fit to flat surface with three screws supplied ensuring 4 inch “O” ring is positioned under base. Run wires from back of lamp.
Traffic/Arrow Board Lamps - 140mm x 83mm
Arrow Board Lamps - 109mm Diameter x 39mm high
• 83R
• 83G
140mm
83mm
Product Description:
Powered by 48 super bright 30° LED’s with a centre brightness exceeding 500cd, 2 intensities low and standard. High impact acrylic lens and ABS base for strength and durability. The lamp uses the standard 4” round grommet (53101) and brackets (53101B or 53101C) and comes with the 55062, 3 pin oval plug.
Part no 5526A
Voltage: 12 volt only
Cable: Use Part number 55062
Packaging: Poly bag of 1
Intensity: Centre brightness 500cd
Current: (Low intensity @ 12 volt 0.04 Amps) & (Standard Intensity @ 12 volt 0.43 Amps)
Fitting: Retro fit to existing fittings, if new installation fit grommet or flange into cutout, plug wire into lamp and run through back then push into grommet/flange.
• 5526A
No compliancy
83A conforms to Australian Standard, AS 41952-2006
• 55062
109mm
53mm
135mm 115mm 113mm142mm
25mm 15mm
109mm
39mm
Grommet Bracket
5
YEAR WARRAnTY
5
YEAR WARRAnTY
• 83A
72Information Correct at time of printing
• 7790BM • 7790WM
Product Description:
The 7790 series are also ECE compliant for use as a daytime running lamp. They are waterproof, sea/salt spray resistant, with durable powder coated aluminium housing, and high impact acrylic lens. Powered by 9 high brightness 1 watt LED’s.
Part no 7790BM 7790WM
Voltage: 12-24 Volt 12-24 Volt
Cable: 30cm sheathed hard wired 30cm sheathed hard wired
Packaging: Blister hang/stand pack of 1 Blister hang/stand pack of 1
Illuminance: @ 1 metre - 520lx
Current: @13.8Volts 0.97Amps - @28Volts 0.44Amps
C.R.n: Approval TBA
Fitting: Fix to mounting surface using stainless steel bolts and adjustable stainless steel bracket supplied.
Product Description:
These waterproof lamps are ECE approved, with durable powder coated aluminium housing, and polycarbonate lens. Powered by 5 high brightness 1 watt LED’s.
Part no 84DTRM
Voltage: 9 - 36 Volt
Cable: 50cm sheathed with plugs and fittings
Packaging: Boxed kit of left and right sides
Current: @13.8Volts (1.33Amps) - @28Volts (0.64Amps)
C.R.n: Component number 600100
Fitting: Fit to vehicle horizontally to the ground using brackets, wiring harness and screws supplied. Please refer to ADR 13/00 for mounting instructions.
• 84DTRM
Daytime running Lamps - 169mm x 60mm x 77mm
Daytime running Lamps - 208mm x 74mm x 23mm
60mm
169mm
77mm
23mm
74mm
208mm
23mm
74mm
208mm
ECE approved
5
YEAR WARRAnTY
5
YEAR WARRAnTY
nEW
PRODUCT
73 Information Correct at time of printing
Product Description:
The 380 series door entry lamps with yellow lens, fully sealed and water proof. They have 18 high brightness LEDs with the lamps inside a 90º low profile rounded housing. These lamps are perfect for caravans, trucks RVs or any door entry application that requires yellow ambient lighting.
Yellow Light Lamps
• 380YCEL - 12 volt only• 380YCEL - 12 volt only
Please refer to page 63 for detailed series specifications
Product Description:
These lamps are for interior use only, using white SMD LED’s with high light output and a 120° light spread and incorporating a yellow lens for yellow ambient light . Low profile design for small spaces, an unobtrusive yet stylish look.
• 1061Y - 12 volt only
Please refer to page 60 for detailed series specifications
Product Description:
These work lamps are waterproof and sea/salt spray resistant, with durable powder coated aluminium housing, yellow coloured polycarbonate lens and ABS adjustable or removable visor. Powered by 6 high brightness 1 watt LED’s.
• 7451YBM - 12-24 volt
Please refer to page 55 for detailed series specifications
• 143YILC - 12 volt only
Product Description:
These lamps are interior only and have an ON/DOOR/OFF switch. 120 white SMD LED’s equivalent to a 50 watt globe give incredible high light output with a 120° light spread and incorporating a yellow lens for yellow ambient light.
Please refer to page 59 for detailed series specifications
Product Description:
The 75 series interior or exterior lamps have SMD LED’s, incredible high light output and 120° of light spread with a yellow lens for yellow ambient illumination.
• 7524YC - 12 volt only
Please refer to page 58 for detailed series specifications
Insects and Humans see light differently. Light sources which radiate ultraviolet and blue light are more attractive to flying insects. Yellow light or incandescent yellow are difficult for insects to see therefore do not attract insects to the light source. Ideal for caravan and camping.
74Information Correct at time of printing
Product Description: ADR compliant for both horizontal or vertical mount. Highest quality adhesive tape used for secure and lasting application.
Part no 7030R 7030RB 7030A 7030AB 7030W 7030WB
Packaging: Blister of 2 Box of 100 Blister of 2 Box of 100 Blister of 2 Box of 100
C.R.n: (Red 38102) (Amber 38101) (White 38103)
Fitting: Remove tape backing and place onto flat surface, apply firm hand pressure to ensure adhesion. Please refer to ADR 13/00 for mounting instructions.
Product Description: ADR compliant for both horizontal or vertical mount. Supplied in a black mounting bracket.
Part no 7035R 7035RB 7035A 7035AB 7035W 7035WB
Packaging: Blister of 2 Box of 100 Blister of 2 Box of 100 Blister of 2 Box of 100
C.R.n: (Red 38102) (Amber 38101) (White 38103)
Fitting: Fit onto flat surface using screw points in bracket. Please refer to ADR 13/00 for mounting instructions.
• 7030R • 7030RB• Red Reflex Reflector
• 7035R • 7035RB• Red Reflex Reflector
• 7035W • 7035WB• Amber Reflex Reflector
• 7035W • 7035WB• White Reflex Reflector
• 7030A • 7030AB• Amber Reflex Reflector
• 7030W • 7030WB• White Reflex Reflector
reflex reflectors - 70mm x 30mm x 6mm
reflex reflectors with Mounting Bracket93mm x 35mm x 7mm
93mm
81mm
35mm
7mm
93mm
81mm
35mm
7mm
30mm
6mm
70mm
30mm
6mm
70mm
ADR/ECE approved
ADR/ECE approved
ADR/ECE approved
WARRAnTY
5
YEAR
WARRAnTY
5
YEAR
WARRAnTY
5
YEAR
Product Description:
To be used at the back of the 200/207 series double lamp assemblies (see page 25), same bolt pattern allowing a red reflector to be part of the fitted assembly.
Part no 7030R-1
Packaging: Poly bag of 1
Warranty: 5 years
C.R.n: (Red 38102)
Fitting: Place frame at back of double lamp assembly lining up existing bolt pattern, ensure reflector is facing to the back of the vehicle. Please refer to ADR 13/00 for mounting instructions.
• 7030R-1
Frame with red reflector - 238mm x 96mm x 6mmsuitable for the 200 series Double lamps
96mm
6mm
238mm
nEW
PRODUCT nEW
PRODUCT nEW
PRODUCT
75 Information Correct at time of printing
Product Description:
The Safety Flash Unit is designed to assist vehicles who pull up on the side of the road and wish to draw attention to the fact that they are parked or stationary to passing vehicles. Examples of the application are in a break down situation or for a road side delivery / service vehicle.Two or more rear facing amber lights mounted on the vehicle at the passing driver’s eye level is a more effective method of attracting the attention of the passing driver. Hazard lights can sometimes be below the drivers eye line and are often confused as indicators or signalling a change of lane rather than the fact that you are stationary.The Safety Flash Unit reduces this problem by allowing the operator to turn on the rear facing lights in the cabin before exiting. With the unit in front of the operator, you can adjust the speed of the alternating flash rate according to your requirements. LED’s on either side of the flash rate knob indicate the flashing rate.
Part no SFU1
Voltage: 12 or 24 volt DC capable
Packaging: Blister of 1
Output: 2 Channels, 1 Amp which equates to 4 LED Amber lamps per channel
Fitting:
Installation, two available options: 1 - Use double sided tape to attach to dashboard, supplied with unit. 2 - Open the case from the right hand side using a flat blade screw driver, and use the 2 screw positions to screw the base to the dashboard. Then replace the lid of the case.Important installation note: It is important to consider the mounting location of the rear facing lights to keep them away from the existing indicator lights on the vehicle.To obtain the best possible attention from other drivers, mount the 2 rear facing lights on each side of the vehicle – effectively allowing as much distance between the 2 lights as possible.
• SFU1• Adjustable flash unit
Product Description:
The ACDC1 solves a problem in the transport industry where some trucks have an output in AC only. AC voltage can damage some brands of LED lights! By simply connecting this unit to the output of the AC down converter, the ACDC1 will convert the AC signal to a rectified and regulated 12 volt DC output and supply the LED lights with an acceptable voltage source that will keep them running for years to come.
Part no ACDC1
AC input: 12-18volts AC
DC Output: Regulated 12 volt DC out
Output Current: Maximum of 2 Amps DC
Packaging: Poly bag of 1
Fitting: Fit box to inside of cabin; 2 brown wires for AC input, 1 red wire for 12 volt positive output and 1 white wire for the output negative or ground connection. Protection with a 2 Amp fast blow M205 fuse on the input (AC) internal to the ACDC1 box.
• ACDC1• AC to DC converter
Adjustable Flash unit - 135mm x 38mm x 24mm
Ac to Dc converter
76Information Correct at time of printing
• PLR12• Red lamp
• PLA12• Amber lamp
• PLB12• Blue lamp
• PLG12• Green lamp
• PLW12• White lamp
Product Description: Coloured pilot lamps with stainless steel nuts and housing. Perfect for console or dash indication lights, fully sealed for interior or exterior applications.
Part no PLR12 PLA12 PLB12 PLG12 PLW12
Voltage: 12 Volt 12 Volt 12 Volt 12 Volt 12 Volt
Cable: 40cm 40cm 40cm 40cm 40cm
Packaging: Blister of 1 Blister of 1 Blister of 1 Blister of 1 Blister of 1
Current: @13.8Volts (0.03Amps) @13.8Volts (0.03Amps) @13.8Volts (0.02Amps) @13.8Volts (0.02Amps) @13.8Volts (0.02Amps)
Fitting: 12mm hole required for fitting.
BACK OF LAMP
Power wire “+”
Load resistor
Crimp terminals
Crimp terminals
Earth wire “-”
Must be mounted on metal surface, the resistor can reach temperatures of up to 170° Celsius
You may require up to 1 resistor per function on each side.
Product Description:
Dummy load resistors designed to draw the same current as a 21 watt globe. Can be used on vehicles that have electronic components that are not LED compatible. Note; resistor can reach 170° celsius, must be mounted onto metal surface.
Part no LR12/2 LR24/2
Voltage: For 12 Volt system only For 24 Volt system only
Packaging: Blister of 2 Blister of 2
Fitting:
The Resistor should ALWAYS be wired between the input wires of the lamp, NOT the chassis of the vehicle or trailer! If fitted to the Chassis, a bad earth connection is possible, and can result in problems with the lighting system of the vehicle!Indicator Circuit:If fitting to the indicator circuit, fit one lead of the resistor to the positive supply side (Yellow wire) and the other lead of the resistor to the negative supply or ground input wire (White).brake Circuit:If fitting to the brake circuit, fit one lead of the resistor to the positive supply side (Red Wire) and the other lead of the resistor to the negative supply or ground input wire (White)Actual Fitting:To fit the resistor, use the crimp terminals supplied. Cut the loom and re-connect the cut wires within the supplied crimp terminal with one side of the resistor crimped into that terminal. Repeat the process for the remaining wire and the other end of the resistor.Use the 2 screw down points on the resistor to secure it to a metal chassis.Important notice:Must be mounted on metal surfaces, the resistor can reach up to 170 deg C, do not mount the resistor on any surface that can be melted by the heat of the resistor, this includes plastics, hoses or painted surfaces.
• LR12/2 • LR24/2
pilot Lamps - 14mm x 30mm
Load resistors
14mm12mm
30mm
5
YEAR WARRAnTY
77 Information Correct at time of printing
cATEgorY 6 siDE DirEcTion inDicATors
150mm x 88mm x 30mm.
150mm 30mm
88mm
30mm
150mm 30mm
88mm
30mm
150mm 30mm
88mm
30mm
Product Description:
The 3102 series Category 6, side direction indicators are available in a chrome or black ABS/polycarbonate mounting bracket. They are fully sealed,water proof with tough ABS lens.
Part no 3102BM 3102CM
Voltage: 9 Volt - 33 Volt 9 Volt - 33 Volt
Cable: 19cm 19cm
Packaging: Box of 1 Box of 1
Warranty: 5 Year 5 Year
LED Qty: 11 11
Lens Type: ABS ABS
base: ABS/Polycarbonate ABS/Polycarbonate
Current: @13.8v (0.20Amp) - @28v ( 0.10Amp)
E.C.E: ECE 60 1 E4
C.R.n: 61333
box Qty: 50 50
barcode: 9335962009435 9335962010059
Fitting: Left or right hand mountable. Surface mount bracket onto flat surface horizontally to the ground using three screw points, run wires through back and clip lens into place. Please refer to ADR 13/00 for mounting instructions.
Part No: 3102BM
Part No: 3102CM
NEW PRODUCT 21/12/2011
78Information Correct at time of printing
Part No.: LWL8312WM
NEW PRODUCT 21/12/2011
Shining in the spotlight...
Description:
Voltage:
Cable:
Packaging:
Current:
Warranty:
Compact high powered work lamp.
10V-30V
50cm hard wired
Single blister hang pack
@13.8Volts (0.68Amps)@28Volts (0.36Amps)
3 Years
Part No.: LWL8312BM
10V-30V input voltage
High intensity 3W SMD LEDs
100% Water & dust proof IP67
3 year warranty
111m
m
65mm84mm
LED Technologies has a brand new edition to its powerful worklamp range. Introducing the all new 84mm round lamp with an aluminium cast casing and polycarbonate lens, this tough lamp is suitable for any heavy duty application. The lamp is IP67 rated and features 4 powerful 3 watt LEDs combined with a complex shape chrome reflector to provide the ultimate in lighting performance. Available in both black and white finishes, with a stainless steel bracket, this compact high performance lamp will suit any extreme application.
111m
m
65mm84mm
0
-5000mm2000mm 7000mm 12000mm 17000mm 22000mm
5000mm
79 Information Correct at time of printing
NEW PRODUCT 30/3/2012
Description:
Voltage:
Packaging:
Current:
Warranty:
Licence plate lamp with black housing. ECE approved E9 L00 1248.
12V-24V
Bulk box of 1
@13.8V (0.07Amps) @28V (0.05Amps)
5 Years
12V-24V input voltage
100% Water & dust proof
4 Bright SMD LEDs
5 year warranty
72mm
45mm
41mm
50mm
Part No.: 40BLMBList Price: $9.90+gst
Number plates are clearly seen...
LED Technologies have just released a brand new Licence Plate Lamp into their range. Featuring a tough polycarbonate lens with an ABS base for extra durability and four super bright SMD LEDs, this lamp will surely impress. They come standard in 12-24 volt with 23cm of hard wired cable and are backed by a 5 year warranty. One lamp on the long edge of a licence plate is required for ADR compliance (with ECE approval) which make them a very economical alternative. The 40 series licence plate lamps are perfect for any vehicle or trailer application where licence illumination is required.
80Information Correct at time of printing
81 Information Correct at time of printing
*Subject to availability. Colours and styles may vary.
proMoTionAL proDucTs* We have a range of posters available for distributors and resellers.
These are normally released to coincide with our advertising schedule.
82Information Correct at time of printing
Corflute Signs
Catalogues, Brochures and Flyers
*Subject to availability. Colours and styles may vary.
Product Catalogue No 5Automotive Marine Industrial
LED Technologies Excellence in Lighting Solutions
Designers and Manufacturers
Products made in Australia and Taiwan
Hats, Stubby Holders and Pens
proMoTionAL proDucTs* We have a range of marketing material, internal signs
and product catalogues available for distributors and resellers.
83 Information Correct at time of printing
LED sTorE MErchAnDisErsPerfect for resellers who display stock in store
and service retail clients.
R-1 Small Merchandiser
R-2 Small Merchandiser
Qty Part #
2 58ARM
2 58AM
2 58RM
2 58WM
2 30BLM
2 200BSTIM
2 1016
Qty Part #
2 1031
2 1061
2 7524W
2 150BAR2
2 100BAR2
2 207BARLP2
1 DB2 (optional)
Qty Part #
2 58ARM
2 58AM
2 58RM
2 58WM
2 30BLM
2 200BSTIM
2 7524C
Qty Part #
2 1016
2 1031
2 1061
2 150BAR2
2 100BAR2
2 207BARLP2
1 DB2 (optional)
*Steel racking not supplied
*Steel racking not supplied
84Information Correct at time of printing
LED sTorE MErchAnDisErsPerfect for resellers who display stock in store
and service retail clients.
Generation One Series Merchandiser
Generation Two Series Merchandiser
Qty Part #
2 35ARM
2 35AM
2 35RM
2 35WM
2 35BLM
2 80BSTIM
2 80AM
2 80RM
2 80WM
2 80BARM
2 80BARRM
Qty Part #
2 80BARWM
2 100BSTIM
2 100BARRM
2 100BARWM
2 125BARRM
2 125BARWM
2 235R
2 235A
2 235W
4 LR12
4 LR24
QTY Part #
2 58ARM
2 58AM
2 58RM
2 58WM
2 35BLM
2 100ARM
2 100BAR2
2 150ARM
2 150BAR2
2 275ARM
2 275BAR2
2 207BARLP2
QTY Part #
2 200BARLP2
2 8MCABLE
2 LP1
2 5C81
2 5C41
2 4C110C
2 4C150C
2 4C210C
2 5C430C
2 5C490C
2 5C670C
*Steel racking not supplied
*Steel racking not supplied
85 Information Correct at time of printing
LED sTorE MErchAnDisErsPerfect for resellers who display stock in store
and service retail clients.
200 Series Merchandiser
Truck Series Merchandiser
QTY Part #
4 35ARM
2 35AM
2 35RM
2 35WM
2 35BLM
2 200BSTIM
2 200BAM
2 200BWM
2 200BRM
2 200BARM
2 200BRWM
2 200BAAM
QTY Part #
2 200BRRM
2 200BARRM
2 200BARWM
2 200BAAAM
2 200BRRRM
2 J9BARRM
2 J9BARWM
6 7030A
6 7030R
6 7030W
2 LR12/2
QTY Part #
2 110AM
2 110RM
2 110WM
2 130AM
2 130RM
2 130WM
2 100RM
2 100WM
2 100AM
2 100BARWM
2 100BARRM
2 125AM
2 125RM
2 125WM
QTY Part #
2 125BARRM
2 125BARWM
4 LR12
4 LR24
6 7030A
6 7030R
6 7030W
4 59401C
4 53101C
4 59401B
4 53101B
4 53102
4 59401
4 53101
*Steel racking not supplied
*Steel racking not supplied
86Information Correct at time of printing
LED sTorE MErchAnDisErsPerfect for resellers who display stock in store
and service retail clients.
Truck/Trailer Merchandiser
Caravan & Trailer Series Merchandiser
Qty Part #
2 58ARM
2 58AM
2 58RM
2 58WM
2 35BLM
2 35CLM
2 38AM
2 38RM
2 38WM
2 38ARM
2 38ARMBKT
2 100ARM
2 150ARM
2 275ARM
Qty Part #
2 200BARLPM2
2 80BARM
2 80BARRM
2 100BARRM
2 100BARWM
2 125BARRM
2 235R
2 235A
2 235W
4 LR12
4 LR24
2 7030A
2 7030R
2 7030W
Qty Part #
2 35ARM
2 35RM
2 35WM
2 35AM
2 58ARM
2 58RM
2 58WM
2 58AM
2 35BLM
2 35CLM
2 38AM
2 38RM
2 38WM
2 38ARM
2 80BARRM
2 100BARRM
Qty Part #
2 200RM
2 200BARM
2 110AM
2 110RM
4 53101H
2 143120W12
2 1016
2 1031
2 1061
2 7524W
2 79WWR12
2 7030A
2 7030R
2 7030W
2 LP1
*Steel racking not supplied
*Steel racking not supplied
87 Information Correct at time of printing
LED sTorE MErchAnDisErsPerfect for resellers who display stock in store
and service retail clients.
Truck/Trailer and Accessories Merchandiser
Qty Part #
4 58AM
6 58ARM
4 58RM
4 58WM
4 38AM
4 38ARM
4 38RM
2 38ARMBKTR
2 38ARMBKT
4 38WM
4 35BLM
4 30BLM
4 150ARM
4 100ARM
4 275ARM
2 207BARLP2
2 80BARM
2 80BARRM
Qty Part #
2 80BARWM
2 100BARRM
2 100BARWM
2 125BARRM
2 125BARWM
2 J9BARRM
2 110AM
2 110RM
2 110WM
2 130AM
2 130RM
2 130WM
6 59401H
6 59401C
6 53101H
6 53101C
12 53102H
2 75O12
Qty Part #
2 75R12
2 75B12
2 75Y12
2 1016
2 1061
2 1031
2 10121
2 7524W
2 7525C
2 143120W
2 148BW12
2 148WW12
2 52WG
2 52WR
4 LR12
4 LR24
*Steel racking not supplied
88Information Correct at time of printing
LED sTorE MErchAnDisErsPerfect for resellers who display stock in store
and service retail clients.
Expo 1 Merchandiser
Expo 2 Merchandiser
Qty Part #
2 100BAR2
2 135ARM
2 150BAR2
2 200BSTIM
2 200CSTIM
2 207BARLP2
2 235A12
2 235R12
2 235W12
2 30CLM
2 35AM
2 35ARM
Qty Part #
2 35BLM
2 35RM
2 35WM
2 52WG
2 52WR
2 68B
2 68G
2 68I
2 68O
2 68P
2 68R
2 68W
Qty Part #
2 68Y
2 7030A
2 7030R
2 7030W
2 80BARM
2 80BARRM
2 80BARWM
2 80BSTIM
2 LR12
2 LR24
2 TK5
Qty Part #
2 100BAR2
2 150BAR2
2 200BSTIM
2 207BARLP2
2 235A12
2 235R12
2 80BARM
2 80BARRM
2 80BARWM
2 80BSTIM
2 35BLM
2 58AM
2 58ARM
2 58RM
2 58WM
2 4C110C
2 4C150C
2 4C190C
2 5C41
2 5C490C
2 5C610C
2 5C81
2 6505BM
2 6505GM
2 6505IM
2 6505OM
2 6505PM
2 6505RM
2 6505WM
2 6505YM
Qty Part #
2 68B
2 68G
2 68I
2 68O
2 68P
2 68R
2 68W
2 68Y
2 1031
2 1061
2 10121
2 1016OPAQUE
2 1031OPAQUE
2 148BW12
2 148WW12
2 7524C
2 7524W
2 7524WB
2 7524WR
2 79BWR12
2 79GWR12
2 79SWR12
2 LP1
2 LR12
2 LR24
2 TK5
2 7030A
2 7030R
2 7030W
*Steel racking not supplied
*Steel racking not supplied
89 Information Correct at time of printing
LED sTorE MErchAnDisErsPerfect for resellers who display stock in store
and service retail clients.
Expo 3 Merchandiser
Qty Part #
2 100ARM
2 100BAR2
2 100BSTIM
2 135AM
2 135ARM
2 135RM
2 135WM
2 150ARM
2 150BAR2
2 200BARM
2 200BSTIM
2 207BARLP2
2 235A12
2 235R12
2 235W12
2 275ARM
2 275BAR2
2 80AM
2 80BARM
2 80BARRM
2 80BARWM
2 80BSTIM
Qty Part #
2 80RM
2 80WM
2 30BLM
2 35BLM
2 38AM
2 38ARM
2 38ARMBKT
2 38RM
2 38WM
2 52WG
2 52WR
2 58AM
2 58ARM
2 58RM
2 58WM
2 4C150C
2 4C190C
2 4C210C
2 5C41
2 5C490C
2 5C610C
2 5C730C
Qty Part #
2 5C81
2 6505BM
2 6505GM
2 6505IM
2 6505OM
2 6505PM
2 6505RM
2 6505WM
2 6505YM
2 68B
2 68G
2 68I
2 68O
2 68P
2 68R
2 68W
2 68Y
2 7030A
2 7030R
2 7030W
2 7450B12
2 7450W12
Qty Part #
2 7524C
2 7524W
2 7524WB
2 7524WR
2 1016
2 1031
2 1061
2 10121
2 1016OPAQUE
2 1031OPAQUE
2 148BW12
2 148WW12
2 79BWR12
2 79GWR12
2 79SWR12
2 LP1
2 LR12
2 LR24
2 TK5
*Steel racking not supplied
90Information Correct at time of printing
Product Description: LED mini display board, self standing or fix to wall with 3M mounting tape supplied. Operating in a 5 second chasing sequence.
Part no,Packaging DB1 - Box of 1 DB2 - Box of 1 DB3 - Box of 1 DB4 - Box of 1
Voltage: 240 volt with transformer 240 volt with transformer 240 volt with transformer 240 volt with transformer
Included Accessories: 240 volt transformer & 3M double sided mounting tape
Display Contains:
80BAR, 35AM, 35RM, 35WM, 7524C, 35BLM
150BAR, 58AM, 58RM, 58WM, 1016/OPAQUE, 1031, 30BLM x 2
7524WR, 7524W, 68R, 68W, 6505RM, 6505WM, 52WG, 52WW, 52WR
1031OPAQUE, 68O, 68P, 68Y, 68B, 68R, 68G, 1031
Dimensions: 282mm x 201mm x 38mm 282mm x 201mm x 38mm 282mm x 201mm x 38mm 282mm x 201mm x 38mm
Warranty 5 years 5 years 5 years 5 years
box Qty: 5 5 5 5
DispLAY BoArDsLight up display board featuring our most popular lamps.
Let your customers see how good our lamps look.
DB1
DB3
DB2
DB4
Displays in Active Mode
282mm
201mm
16mm38mm
282mm
201mm
16mm38mm
91 Information Correct at time of printing
Warranty/Return for Credit Claim Form
1. Generation II products have a lifetime warranty. We consider 20 years to be the lifetime of a trailer.2. Automotive products have a 5 year warranty, MaXilamp series have a 7 year warranty.3. Interior and courtesy lamps have a 3 year warranty4. Commercial lighting lamps have a 2 year warrantyThis warranty covers faults in components and workmanship of the lamp itself when used under normal conditions and does not cover:• Faulty Installation • Over Voltage• Accidental Damage • Excessive Heat Damage• Misuse or Abuse • Freight Charges• Cost of labour for removal and replacement of product
WARRANTY PROCEDUREAll warranty returns must be tested off the vehicle to ensure that the unit is at fault. This can be done by simply attaching the lamps to a fully charged 12 volt battery. Do not replace any products to your customers unless you are 100% sure that the product is faulty and will be covered under warranty.If the unit is faulty, return it to your place of purchase so it can be directed to the LED Technologies warranty department for full testing and evaluating.Note: Most of our rear lamp assemblies are designed so that if one insert is damaged it can be replaced easily without replacing the complete light assembly; only return the faulty insert and not the entire assembly.
RETURN FOR CREDITAny product that is returned for a credit and not as a warranty claim, must be in original clean resaleable condition. The packaging must not be opened, sun damaged, UV faded or tampered with.
Warranty Claims and Return for Credit can be returned to us at.LED Technologies Pty. Ltd.12 Brand DriveThomastown Victoria 3074Attention: Warranty Department
Name: ___________________________________________________________________________________________
Address: _________________________________________________________________________________________
Phone: ______________________________________________Email: _______________________________________
Date of Purchase: ___________________________ Place of Purchase: _______________________________________
Part Number/s: ____________________________________________________________________________________
Description of fault/Reason for return: __________________________________________________________________
_________________________________________________________________________________________________
_________________________________________________________________________________________________
_________________________________________________________________________________________________
_________________________________________________________________________________________________
Vehicle fitted to: ___________________________ Voltage of Vehicle: _______________________________________
Lamp has been tested off the vehicle or trailer, please tick (only for warranty claims).
Please photocopy this form for warranty claims
92Information Correct at time of printing
ExciTing nEW proDucTs For 2011
J3 Twin Combination Page 20
102 Series Stop/Tail/Indicator/Reverse Page 38
143 Series Marine Interior Lamps Page 53
305 Series Coloured Interior Lamps Page 65
380EL Series Caravan Door Entry Lamps Page 63
J3 Triple Combination Page 20
J3 Single Page 20
150 Series with Licence Plate Lamp Page 15
100 Series with Licence Plate Lamp Page 15
250 Series Combination Lamps Page 18
275 Series Combination Lamps Page 18
131 Series Rectangular Lamps Page 36
235 Series with Twin Bracket Page 28
380 Series with Single Bracket Page 35
380 Series with Twin Bracket Page 28
80 Series Triples with Mounting Bracket Page 22
7035 Reflex Reflectors Page 73
101 Series Lamps Page 14
151 Series Lamps Page 14
42 Series Marker Lamps Page 45
36 Series Marker Lamps Page 44
42 Series Marker Lamps Page 51
42 Series Marker Lamps Page 48
72 Series Work Lamps Page 56