Date post: | 08-Mar-2016 |
Category: |
Documents |
Upload: | mp-lighting |
View: | 246 times |
Download: | 18 times |
Contents
Introduction 3
Product Overview 4
Wall, Floor & Ceiling Fixtures 6
Cabinet Fixtures 82
Canopy Mount & Rail Systems 102
Picture Lights 116
Pendants 122
Linear Systems 136
Desk & Table Fixtures 156
Hardware 160
Accessories 175
Drivers 176
Driver Enclosures 183
Magnetic Low Voltage Transformers 184
Recommended Driver Chart 186
Lamp Index & Isofootcandle Calculation 191
Explanation of Symbols 192
Mounting & Finishing Options 193
Online with MP Lighting 194
Research & Development 195
Terms & Warranty 196
Index 197
www.mplighting.com
2
3
The realities of LED lighting are clearwith an average product life of 50,000 hours, LEDs are the most energy efficient and cost effective lighting option on the market. They contain no mercury or moving parts that could break, leak or shatter, limiting their impact on the environment. The right LED lighting can instantly enhance any space, while allowing users to conserve energy and save money.
At MP Lighting, we are committed to providing you with the most current information and technology related to solid-state lighting. Our LEDs are produced using quality materials and are tested to ensure reliability and performance. We use high output lamps which are 10 to 20 times brighter than standard LEDs to ensure optimal light output and efficacy is achieved in each application. Our LED thermal management system ensures an efficient performance and utmost product life.
Our commitment to quality products extends beyond their construction. When our LED products can no longer be used, all product parts are recyclable. The end result of our commitment is a clean, clear, and energy-efficient light guaranteed to complement any design.
Introduction
L01 (p.6-7)
L51, 1W / 2.5W (p.82-83)
L21 (p.38-39)
L12 (p.22-23)
L37 (p.54-55)
L05 (p.14-15)
L57, 3 x 1W (p.90-91)
L33 (p.46-47)
L16 (p.30-31)
L02 (p.8-9)
L52, 1W / 2.5W (p.84-85)
L22 (p.40-41)
L130 (p.66-67) L131 (p.68-69)
L13 (p.24-25)
L06 (p.16-17)
L58, 2.5W (p.92-93)
L34 (p.48-49)
L17 (p.32-33)
L03 (p.10-11)
L55, 3 x 1W (p.86-87)
L31 (p.42-43)
L14 (p.26-27)
L07 (p.18-19)
L59, 3.7W (p.94-95)
L35 (p.50-51)
L18 (p.34-35)
L04 (p.12-13)
L56, 3 x 1W (p.88-89)
L32 (p.44-45)
L15 (p.28-29)
L11 (p.20-21)
L62, 3.2W (p.96-97)
L36 (p.52-53)
L141 (p.74-75) L142 (p.76-77)L134 (p.70-71) L151 (p.78-79)L135 (p.72-73) L181 (p.80-81)
L19 (p.36-37)
L92 (p.58-59) L97 (p.60-61) L98 (p.62-63)L91 (p.56-57) L99 (p.64-65)
Wall, Floor & Ceiling Fixtures
Cabinet Fixtures
Product Overview
L64, 2.5W (p.98-99)
L65, 2.5W (p.100-101)
www.mplighting.com
5
4
L96 (p.122-123) L191 (p.124-125)
L101, 1W (p.136-137)
L200 (p.156-157)
L121, 0.07W (p.150-151)
L202 (p.120-121)
G02L (p.126-127)
L102, 0.07W (p.138-139)
L161, 1W (p.152-153)
L81 (p.116-117)
L106, 1W (p.144-145)
G03L (p.128-129)
L103, 1W (p.140-141)
L171, 1W (p.154-155)
L203 (p.158-159)
L85 (p.118-119)
L111, 1W (p.146-147)
L104, 1W (p.142-143)
L112, 2.5W (p.148-149)
Picture Lights
Pendants
Linear Systems
Desk & Table Fixtures
Product OverviewL72 (p.102-103) L221 (p.110-111)L73 (p.104-105) L222 (p.112-113)L75 (p.106-107) L76 (p.108-109)
Canopy Mount & Rail Systems
L223 (p.114-115)
P71L (p.130-131) P81L (p.132-133) P82L (p.134-135)
Image shows L01-1W30SNC30-S2MA
1-5/841mm
4-1/8105mm
1/83mm
Standard flange7/8 (22mm)
2-1/457mm
Concrete pouring line
Base Height
4-7/8124mm
2-3/470mm
Splice box with 1/2 NPT I/O ports for connector and wiring.
pavingstone
sand
Paving stoneflange3-5/8 (92mm)
approx. 700 cdmax.
0
180
90
45-45
-90
0 Spread: 14.1 90 Spread: 14.9
9.0
7.5
6.0
4.5
3.0
1.5
2.2
1.9
1.5
1.1
0.7
0.4
2.3
2.0
1.6
1.2
0.8
0.4303.82
75.95
33.76
18.99
12.15
8.44
Center Beam FC Beam Width
Illuminance at a DistanceL011W, 123000K Std85 lm
Polar Candela Distribution
approx. 1300 cdmax.
0
180
90
45-45
-90
0 Spread: 14.1 90 Spread: 14.9
9.0
7.5
6.0
4.5
3.0
1.5
2.2
1.9
1.5
1.1
0.7
0.4
2.3
2.0
1.6
1.2
0.8
0.4579.04
144.76
64.34
36.19
23.16
16.08
Center Beam FC Beam Width
Illuminance at a DistanceL012.5W, 123000K Std162 lm
Polar Candela Distribution
7
6
Wall, Floor &
Ceiling Fixtureswww.mplighting.com
L01
Code WAttAge CoLor BeAM LeNS optIoN** ANgLe BrACket FLANge HeIgHt BASe HeIgHt FINISH
L01 - -
W27S = 2700K, std CRIW30S = 3000K, std CRIW35S = 3500K, std CRIW41S = 4100K, std CRI W20H = 2000K, high CRIW30H = 3000K, high CRI
S = spot (12)N = narrow flood (30)W = wide flood (120)
0 = no angle 30 = 30 angle X = custom (30 max.)
0 = no base2 = 2 (51mm)6 = 6 (152mm)X = custom height
S = standard flange 5/8 (17mm)P = paving stone flange, 3-3/8 (86mm)
MA = matte clear anodizedBA = black anodizedBZ = bronzeS3 = stainless steel 303S6 = stainless steel 316
L01 1W / 2.5W In-ground
Application Outdoor / indoor directional ingrade light for uplighting walls, columns, or architectural features.
Source 1W, 350mA or 2.5W, 700mA LED
Driver Remote 120V primary, 350mA (1W) or 700mA (2.5W) driver (not included).
LED Input Voltage 4V DC
Power Consumption 1.5W / 3W
Dimming 0~10V dimming with remote dimmable driver (not included). See page 186-190 for Recommended Driver Chart.
Weight 1.8lbs net. (0.816kg) (base extra).
Material Solid anodized aluminum or stainless steel with 1/4 (6mm) thick tempered glass lens, suitable for walk-over and drive-over applications. RoHS compliant.
Mounting Comes with splice box, aluminum flange and level gauge. Can be buried in earth/gravel or cast into concrete/paving stone with or without mounting base.
Approval Wet and dry locations. Approved to US and Canadian standards by CSA.
Note Can be used as emergency backup lighting in conjunction with Bodine emergency LED driver (sold separately). Consult factory.
66 See page 192 for explanation of symbols and Ip ratings.
1 = 1W 2 = 2.5W*
*only available in W30S & W20H.
C = clearF = frosted
LM = louver, matte anodizedLB = louver, black anodized
Shown with standard flange (S) and (optional) mounting base.
Lumen test results provided by Led chip manufacturer.
Shown with paving stone flange (p) with no base.
**Louver not available with angle bracket.
NOTE: Standard CrI has a value of 75~82 while high CrI has 92.
W20H has consistent binning that falls within 1.5 MacAdam ellipse.
Image shows L02-1W30SNC30-MA
1-3/444mm
3-1/289mm
125mm
4-1/8105mm
1-3/444mm
1-3/444mm
7/822mm
2-1/457mm
2-1/457mm
1/8 (3mm)Face of drywall
Angle
0
180
90
45
135
-90
approx. 260 cd max.-0
-90
1 0.5 0.2 0.1 fc
Mount height: 1 ft Total LLF: 1
2 4 6 8 10 12 14 16 18
864
20246
8
Polar Candela Distribution Isofootcandle PlotL021W, 303000K Std85 lm
0
180
90
45
135
-90
approx. 480 cd max.-0
-90
2.5 0.5 0.2 0.1 fc
Mount height: 1 ft Total LLF: 1
4 8 12 16 20 240
0
4
4
8
8
10
Polar Candela Distribution Isofootcandle PlotL022.5W, 303000K Std162 lm
9
8
Wall, Floor &
Ceiling Fixtureswww.mplighting.com
L02
Code WAttAge CoLor BeAM LeNS optIoN** ANgLe BrACket FINISH
L02 - -
W27S = 2700K, std CRIW30S = 3000K, std CRIW35S = 3500K, std CRIW41S = 4100K, std CRI W20H = 2000K, high CRIW30H = 3000K, high CRI
0 = no angle 30 = 30 angle45 = 45 angleX = custom (45 max.)
MA = matte clear anodizedBA = black anodizedS3 = stainless steel 303S6 = stainless steel 316
L02 1W / 2.5W Walkway
Application Indoor wall mounted directional or indicator light for stair, ramp, and aisle illumination.
Source 1W, 350mA or 2.5W, 700mA LED
Driver Remote 120V primary, 350mA (1W) or 700mA (2.5W) driver (not included).
LED Input Voltage 4V DC
Power Consumption 1.5W / 3W
Dimming 0~10V dimming with remote dimmable driver (not included). See page 186-190 for Recommended Driver Chart.
Weight 0.35lbs (0.158kg).
Material Solid anodized aluminum or stainless steel with 1/4 (6mm) thick tempered glass lens. RoHS compliant.
Mounting Comes with steel flange which mounts to pre-installed standard 4 (102mm) octagonal box, 1-1/2 (38mm) deep minimum and 1/4 (6mm) setback from face of drywall. Can be wall or ceiling mounted.
Approval Dry locations. Approved to US and Canadian standards by CSA.
Note Can be used as emergency backup lighting in conjunction with Bodine emergency LED driver (sold separately). Consult factory.
53 See page 192 for explanation of symbols and Ip ratings.
1 = 1W 2 = 2.5W*
LM = louver, matte anodizedLB = louver, black anodized
S = spot (12)N = narrow flood (30)W = wide flood (120)
C = clearF = frosted
*only available in W30S & W20H.
NOTE: Standard CrI has a value of 75~82 while high CrI has 92.
W20H has consistent binning that falls within 1.5 MacAdam ellipse.
**Max. 30 angle bracket with louver opion.
Lumen test results provided by Led chip manufacturer.
Image shows L03-1W30SNC0-B6MA
2-1/457mm
376mm 1/8
3mm
1-1/829mm
3-1/289mm
Concrete pouring line
4-3/8111mm Buna rubber gasket sealing, tight to keep
in position even when upside down.
Mounting box with 1/2 NPT I/O ports for connector and wiring.
4-3/8111mm
Mounting box with 1/2 NPT I/O ports for connector and wiring.
4-1/8105mm
1-5/841mm
Angle
0
180
90
45
135
-90
approx. 28 cd max.-0
-90
2.5 0.5 0.2 0.1 fc
Mount height: 1 ft Total LLF: 1
1 2 3 4 5 6 7 8 9
864
20246
8
Polar Candela Distribution Isofootcandle PlotL031W, 1203000K Std85 lm
0
180
90
45
135
-90
approx. 55 cd max.-0
-90
10 1 0.2 0.1 fc
Mount height: 1 ft Total LLF: 1
1 2 3 4 5 6 7 8 9
864
20246
8
Polar Candela Distribution Isofootcandle PlotL032.5W, 1203000K Std162 lm
11
10
Wall, Floor &
Ceiling Fixtureswww.mplighting.com
Code WAttAge CoLor BeAM LeNS optIoN** ANgLe BrACket MouNtINg LeAd LeNgtH FINISH
L03 - -
W27S = 2700K, std CRIW30S = 3000K, std CRIW35S = 3500K, std CRIW41S = 4100K, std CRI W20H = 2000K, high CRIW30H = 3000K, high CRI
B = mounting boxF = flange only
6 = 6 (1829mm)X = custom
MA = matte clear anodizedBA = black anodizedS3 = stainless steel 303S6 = stainless steel 316
L03 1W / 2.5W Submersible
Application Submersed fresh water illumination to 12 (305mm) depth. Perfect for core drilling retrofits without back box and flange.
Source 1W, 350mA or 2.5W, 700mA LED
Driver Remote 120V primary, 350mA (1W) or 700mA (2.5W) driver (not included).
LED Input Voltage 4V DC
Power Consumption 1.5W / 3W
Dimming 0~10V dimming with remote dimmable driver (not included). See page 186-190 for Recommended Driver Chart.
Weight 2.45lbs (1.11kg)
Material Solid anodized aluminum or stainless steel with 1/4 (6mm) thick tempered glass lens and 6 (1829mm) Captire lead. RoHS compliant.
Mounting Comes with mounting box, aluminum flange and level gauge. Can be buried in earth/gravel or cast into concrete for submersed applications.
Approval Submersible. Approved to US and Canadian standards by CSA.
Note Can be used as emergency backup lighting in conjunction with Bodine emergency LED driver (sold separately). Consult factory.
68 See page 192 for explanation of symbols and Ip ratings.
Shown with flange only
Shown with mounting box
1 = 1W 2 = 2.5W*
L03
0 = no angle 30 = 30 angle X = custom (30 max.)
LM = louver, matte anodizedLB = louver, black anodized
S = spot (12)N = narrow flood (30)W = wide flood (120)
C = clearF = frosted
**Louver not available with angle bracket.
*only available in W30S & W20H.
NOTE: Standard CrI has a value of 75~82 while high CrI has 92.
W20H has consistent binning that falls within 1.5 MacAdam ellipse.
Lumen test results provided by Led chip manufacturer.
Image shows L04-1W30SNC30-S2MA
1-5/841mm
4-1/8105mm
1/83mm
Standard flange7/8 (22mm)
Sq.2-1/4Sq.57mm
Concrete pouring line
Base Height
4-7/8124mm
2-3/470mm
Splice box with 1/2 NPT I/O ports for connector and wiring.
pavingstone
sand
Paving stoneflange3-5/8 (92mm)
approx. 700 cdmax.
0
180
90
45-45
-90
0 Spread: 14.1 90 Spread: 14.9
9.0
7.5
6.0
4.5
3.0
1.5
2.2
1.9
1.5
1.1
0.7
0.4
2.3
2.0
1.6
1.2
0.8
0.4303.82
75.95
33.76
18.99
12.15
8.44
Center Beam FC Beam Width
Illuminance at a DistanceL041W, 123000K Std85 lm
Polar Candela Distribution
approx. 1300 cdmax.
0
180
90
45-45
-90
0 Spread: 14.1 90 Spread: 14.9
9.0
7.5
6.0
4.5
3.0
1.5
2.2
1.9
1.5
1.1
0.7
0.4
2.3
2.0
1.6
1.2
0.8
0.4579.04
144.76
64.34
36.19
23.16
16.08
Center Beam FC Beam Width
Illuminance at a DistanceL042.5W, 123000K Std162 lm
Polar Candela Distribution
13
12
Wall, Floor &
Ceiling Fixtureswww.mplighting.com
L04
L04 1W / 2.5W In-ground
Application Outdoor / indoor directional ingrade light for uplighting walls, columns, or architectural features.
Source 1W, 350mA or 2.5W, 700mA LED
Driver Remote 120V primary, 350mA (1W) or 700mA (2.5W) driver (not included).
LED Input Voltage 4V DC
Power Consumption 1.5W / 3W
Dimming 0~10V dimming with remote dimmable driver (not included). See page 186-190 for Recommended Driver Chart.
Weight 1.83lbs net. (0.83kg) (base extra)
Material Solid anodized aluminum or stainless steel with 1/4 (6mm) thick tempered glass lens, suitable for walk-over and drive-over applications. RoHS compliant.
Mounting Comes with splice box, aluminum flange and level gauge. Can be buried in earth/gravel or cast into concrete/paving stone with or without mounting base.
Approval Wet and dry locations. Approved to US and Canadian standards by CSA.
Note Can be used as emergency backup lighting in conjunction with Bodine emergency LED driver (sold separately). Consult factory.
66 See page 192 for explanation of symbols and Ip ratings.
Code WAttAge CoLor BeAM LeNS optIoN** ANgLe BrACket FLANge HeIgHt BASe HeIgHt FINISH
L04 - -
0 = no angle 30 = 30 angle X = custom (30 max.)
0 = no base2 = 2 (51mm)6 = 6 (152mm)X = custom height
S = standard flange 5/8 (17mm)P = paving stone flange, 3-3/8 (86mm)
MA = matte clear anodizedBA = black anodizedS6 = stainless steel 316
1 = 1W 2 = 2.5W*
C = clearF = frosted
Shown with standard flange (S) and (optional) mounting base.
Shown with paving stone flange (p) with no base.
LM = louver, matte anodizedLB = louver, black anodized
S = spot (12)N = narrow flood (30)W = wide flood (120)
**Louver not available with angle bracket.
W27S = 2700K, std CRIW30S = 3000K, std CRIW35S = 3500K, std CRIW41S = 4100K, std CRI W20H = 2000K, high CRIW30H = 3000K, high CRI
*only available in W30S & W20H.
NOTE: Standard CrI has a value of 75~82 while high CrI has 92.
W20H has consistent binning that falls within 1.5 MacAdam ellipse.
Lumen test results provided by Led chip manufacturer.
Image shows L05-3W30SFC0-2MA
4-1/2114mm
3-1/879mm
3-5/892mm
2-11/1669mm
4-5/8117mm
6mm1/4
Concrete pouring line
Base Height
4-7/8124mm
2-1/265mm
approx. 650 cdmax.
0
180
90
45-45
-90
0 Spread: 29.9 90 Spread: 30.2
9.0
7.5
6.0
4.5
3.0
1.5
4.8
4.0
3.2
2.4
1.6
0.8
4.9
4.0
3.2
2.4
1.6
0.8294.71
73.68
32.75
18.42
11.79
8.19
Center Beam FC Beam Width
Illuminance at a DistanceL053 x 1W 303000K Std255 lm
Polar Candela Distribution
approx. 1300 cdmax.
0
180
90
45-45
-90
0 Spread: 29.9 90 Spread: 30.2
9.0
7.5
6.0
4.5
3.0
1.5
4.8
4.0
3.2
2.4
1.6
0.8
4.9
4.0
3.2
2.4
1.6
0.8561.68
140.42
62.41
35.10
22.47
15.60
Center Beam FC Beam Width
Illuminance at a DistanceL053 x 2.5W 303000K Std486 lm
Polar Candela Distribution
15
14
Wall, Floor &
Ceiling Fixtureswww.mplighting.com
L05
Code WAttAge CoLor BeAM LeNS ANgLe BrACket BASe HeIgHt FINISH
L05 - -
3 = 3 x 1W7 = 3 x 2.5W*
C = clearF = frosted
0 = no angle 30 = 30 angle
0 = no height2 = 2 (51mm) high6 = 6 (152mm) highX = custom height
MA = matte clear anodizedBA = black anodizedS6 = stainless steel 316
L05 3W / 7.5W In-ground
Application Outdoor / indoor directional ingrade light for uplighting walls, columns, or architectural features.
Source 3 x 1W, 350mA or 3 x 2.5W, 700mA LEDs
Driver Remote 120V primary, 350mA (3W) or 700mA (7.5W) driver, or 12V constant voltage driver (not included).
LED Input Voltage 12V DC
Power Consumption 4W / 9W
Dimming 0~10V dimming with remote dimmable driver (not included). See page 186-190 for Recommended Driver Chart.
Weight 2.56lbs (1.16kg) (base extra).
Material Solid anodized aluminum or stainless steel with 3/8 (10mm) thick tempered glass lens, suitable for walk-over and drive-over applications. RoHS compliant.
Mounting Comes with splice box, aluminum flange and level gauge. Can be buried in earth/gravel or cast into concrete with or without mounting base.
Approval Wet and dry locations. Approved to US and Canadian standards by CSA.
Note Can be used as emergency backup lighting in conjunction with Bodine emergency LED driver (sold separately). Consult factory.
66 See page 192 for explanation of symbols and Ip ratings.
Shown with (optional) mounting base.
N = narrow flood (30)F = flood (60)
W27S = 2700K, std CRIW30S = 3000K, std CRIW35S = 3500K, std CRIW41S = 4100K, std CRI W20H = 2000K, high CRIW30H = 3000K, high CRI
*only available in W30S & W20H.
NOTE: Standard CrI has a value of 75~82 while high CrI has 92.
W20H has consistent binning that falls within 1.5 MacAdam ellipse.
Lumen test results provided by Led chip manufacturer.
Image shows L06-W27SB4-S6
3/419mm
7/822mm
114mm
4-7/8124mm
60mm
Nipple
3/8 IPS Nipple
2-3/8
4-1/2
Concrete pouring line
3/419mm
7/822mm
114mm
4-7/8124mm
60mm
Nipple
3/8 IPS Nipple
2-3/8
4-1/2
Concrete pouring line
approx. 3.3 cdmax.
0
180
90
45-45
-90
0 Spread: 23.4 90 Spread: 23.2
1.0
0.8
0.7
0.5
0.3
0.2
0.4
0.3
0.3
0.2
0.1
0.1
0.4
0.3
0.3
0.2
0.1
0.1119.21
29.80
13.25
7.45
4.77
3.31
Center Beam FC Beam Width
L062700K Std3.2 lm
Illuminance at a DistancePolar Candela Distribution
17
16
Wall, Floor &
Ceiling Fixtureswww.mplighting.com
Shown with base
Shown with no base (to 1/2 Npt connector)
L06
Code CoLor BASe NIppLe FINISH
L06 - W27S - S6
W27S = 2700K, std CRI B = with baseN = no base
2 = 2 (51mm) long4 = 4 (102mm) long8 = 8 (203mm) longX = custom length
S6 = stainless steel 316
L06 0.1W In-ground
Application Outdoor / indoor indicator light for driveway and sidewalk.
Source 0.1W, 20mA LED
Driver Remote 120V primary, 6V constant voltage, 20mA driver (not included).
LED Input Voltage 6V DC
Power Consumption 0.1W
Weight 1.21lbs (0.549kg).
Material Stainless steel 316. RoHS compliant.
Mounting Can be buried in earth/gravel or cast into concrete with or without mounting base.
Approval Wet and dry locations. Approved to US and Canadian standards by CSA.
67 See page 192 for explanation of symbols and Ip ratings.
NOTE: Standard CrI has a value of 75~82.
Lumen test results provided by Led chip manufacturer.
Image shows L07-W27S-S6
3/88mm
3/419mm
1-1/238mm
1/83mm
1/213mm
approx. 3.3 cdmax.
0
180
90
45-45
-90
1.0
0.8
0.7
0.5
0.3
0.2
0.4
0.3
0.3
0.2
0.1
0.1
0.4
0.3
0.3
0.2
0.1
0.1119.21
29.80
13.25
7.45
4.77
3.31
0 Spread: 23.4 90 Spread: 23.2
Center Beam FC Beam Width
L072700K Std3.2 lm
Illuminance at a DistancePolar Candela Distribution
19
18
Wall, Floor &
Ceiling Fixtureswww.mplighting.com
L07
Code CoLor FINISH
L07 - W27S - S6
W27S = 2700K, std CRI S6 = stainless steel 316
L07 0.1W In-floor
Application Outdoor / indoor indicator light for deck flooring.
Source 0.1W, 20mA LED
Driver Remote 120V primary, 6V constant voltage, 20mA (not included).
LED Input Voltage 6V DC
Power Consumption 0.1W
Weight 0.05lbs (0.024kg).
Material Stainless steel 316. RoHS compliant.
Mounting Mounts directly into deck flooring.
Approval Wet and dry locations. Approved to US and Canadian standards by CSA.
67 See page 192 for explanation of symbols and Ip ratings.
NOTE: Standard CrI has a value of 75~82 while high CrI has 92.
Lumen test results provided by Led chip manufacturer.
Image shows L11-1W30SWV-MC
7/8
1-1/2
3-1/4
3-1/8
4-3/4
1-3/835mm
22mm
38mm 79mm
83mm 121mm
1-1/238mm
5/816mm
7/8
1-1/2
3-1/4
3-1/8
4-3/4
1-3/835mm
22mm
38mm 79mm
83mm 121mm
1-1/238mm
5/816mm
7/8
1-1/2
3-1/4
3-1/8
4-3/4
1-3/835mm
22mm
38mm 79mm
83mm 121mm
1-1/238mm
5/816mm
approx. 750 cdmax.
0
180
90
45-45
-90
-0
-90
Mount height: 1 ft Total LLF: 1
0
1
2
3
4
5
2 1 0 1 2 3
0.21.020
0.1 fc
Isofootcandle PlotPolar Candela DistributionL111W, 123000K Std85 lm
approx. 1500 cdmax.
0
180
90
45-45
-90
-0
-90
Mount height: 1 ft Total LLF: 1
0
1
2
3
4
5
2 1 0 1 2 3
0.5
520
0.1 fc
Isofootcandle PlotPolar Candela DistributionL112.5W, 123000K Std162 lm
21
20
Wall, Floor &
Ceiling Fixtureswww.mplighting.com
L11
Code WAttAge CoLor BeAM pLAte FINISH
L11 - -
V = verticalH = horizontal
MC = matte chromeBK = powder coated blackBN = brushed nickel
L11 1W / 2.5W Walkway
Application Indoor stair, ramp, aisle, and walkway illumination.
Source 1W, 350mA or 2.5W, 700mA LED
Driver Integral 120V primary, 3W 350mA (1W) or 9W 700mA (2.5W) non-dimmable driver.
Power Consumption 1.5W / 3W
Dimming 0~10V dimming with remote dimmable driver (not included). See page 186-190 for Recommended Driver Chart.
Weight 0.59lbs (0.266kg).
Material Plated brass, anodized aluminum. RoHS compliant.
Mounting Vertically or horizontally positioned face plate mounts to single gang box (not included). Optimal mounting distance is 18 - 24 (457mm - 610mm) AFF.
Approval Dry locations. Approved to US and Canadian standards by CSA.
Note Can be used as emergency backup lighting in conjunction with Bodine emergency LED driver (sold separately). Consult factory.
50 See page 192 for explanation of symbols and Ip ratings.
Shown as 12 or 30 beam Vertical plate
Shown as 120 beam Vertical plate
Shown as 120 beam Horizontal plate
1 = 1W2 = 2.5W*
S = spot (12)N = narrow flood (30)W = wide flood (120)
W27S = 2700K, std CRIW30S = 3000K, std CRIW35S = 3500K, std CRIW41S = 4100K, std CRI W20H = 2000K, high CRIW30H = 3000K, high CRI
*only available in W30S & W20H.
NOTE: Standard CrI has a value of 75~82 while high CrI has 92.
W20H has consistent binning that falls within 1.5 MacAdam ellipse.
Lumen test results provided by Led chip manufacturer.
Image shows L12-1W30SSW30SS-MC
7/8
1-1/21-3/835mm
2-1/854mm22mm
38mm
3-1/4
3-1/8
4-3/4
79mm
83mm 121mm
1-1/238mm
1-5/841mm
7/8
1-1/21-3/835mm
2-1/854mm22mm
38mm
3-1/4
3-1/8
4-3/4
79mm
83mm 121mm
1-1/238mm
1-5/841mm
7/8
1-1/21-3/835mm
2-1/854mm22mm
38mm
3-1/4
3-1/8
4-3/4
79mm
83mm 121mm
1-1/238mm
1-5/841mm
approx. 300 cdmax.
0
180
90
45-45
-90
-0
-90
0.21.020
0.1 fc
Mount height: 1 ft Total LLF: 1
0
1
2
3
4
5
2 1 0 1 2 3
Isofootcandle PlotPolar Candela DistributionL122 x 1W, 303000K Std170 lm
approx. 550 cdmax.
0
180
90
45-45
-90
-0
-90
0.52.520
0.1 fc
Mount height: 1 ft Total LLF: 1
0
1
2
3
4
5
2 1 0 1 2 3
Isofootcandle PlotPolar Candela DistributionL122 x 2.5W, 303000K Std324 lm
23
22
Wall, Floor &
Ceiling Fixtureswww.mplighting.com
L12
Code WAttAge CoLor up BeAM up CoLor doWN BeAM doWN FINISH
L12 - -
MC = matte chromeBK = powder coated blackBN = brushed nickel
L12 2 x 1W / 2.5W Up and Down Walkway
Application Indoor stair, ramp, aisle, and walkway illumination.
Source 2 x 1W, 350mA or 2 x 2.5W, 700mA LEDs.
Driver Integral 120V primary, 3W 350mA (2W) or 9W 700mA (5W) non-dimmable driver.
Power Consumption 3W / 6W
Dimming 0~10V dimming with remote dimmable driver (not included). See page 186-190 for Recommended Driver Chart.
Weight 0.914lbs (0.415kg).
Material Plated brass, anodized aluminum. RoHS compliant.
Mounting Vertically positioned face plate mounts to a single gang box (not included).
Approval Dry locations. Approved to US and Canadian standards by CSA.
Note Can be used as emergency backup lighting in conjunction with Bodine emergency LED driver (sold separately). Consult factory.
50 See page 192 for explanation of symbols and Ip ratings.
Shown as 12 or 30 beam
Shown as 120 beam
1 = 1W2 = 2.5W*
S = spot (12)N = narrow flood (30)W = wide flood (120)
S = spot (12)N = narrow flood (30)W = wide flood (120)
W27S = 2700K, std CRIW30S = 3000K, std CRIW35S = 3500K, std CRIW41S = 4100K, std CRI W20H = 2000K, high CRIW30H = 3000K, high CRI
W27S = 2700K, std CRIW30S = 3000K, std CRIW35S = 3500K, std CRIW41S = 4100K, std CRI W20H = 2000K, high CRIW30H = 3000K, high CRI
*only available in W30S & W20H.
NOTE: Standard CrI has a value of 75~82 while high CrI has 92.
W20H has consistent binning that falls within 1.5 MacAdam ellipse.
Lumen test results provided by Led chip manufacturer.
Image shows L13-1W30SWV-MC
1-1/4
1-3/835mm
1-3/444mm
32mm
3-1/4
3-1/8
4-3/4
79mm
83mm 121mm
1-1/238mm
1-1/238mm
1-1/4
1-3/835mm
1-3/444mm
32mm
3-1/4
3-1/8
4-3/4
79mm
83mm 121mm
1-1/238mm
1-1/238mm
1-1/4
1-3/835mm
1-3/444mm
32mm
3-1/4
3-1/8
4-3/4
79mm
83mm 121mm
1-1/238mm
1-1/238mm
approx. 750 cdmax.
0
180
90
45-45
-90
-0
-90
Mount height: 1 ft Total LLF: 1
0
1
2
3
4
5
2 1 0 1 2 3
0.21.020
0.1 fc
Isofootcandle PlotPolar Candela DistributionL131W, 123000K Std85 lm
approx. 1500 cdmax.
0
180
90
45-45
-90
-0
-90
Mount height: 1 ft Total LLF: 1
0
1
2
3
4
5
2 1 0 1 2 3
0.5
520
0.1 fc
Isofootcandle PlotPolar Candela DistributionL132.5W, 123000K Std162 lm
25
24
Wall, Floor &
Ceiling Fixtureswww.mplighting.com
L13
Code WAttAge CoLor BeAM pLAte FINISH
L13 - -
V = verticalH = horizontal
MC = matte chromeBK = powder coated blackBN = brushed nickel
L13 1W / 2.5W Walkway
Application Indoor stair, ramp, aisle, and walkway illumination.
Source 1W, 350mA or 2.5W, 700mA LED
Driver Integral 120V primary, 3W 350mA (1W) or 9W 700mA (2.5W) non-dimmable driver.
Power Consumption 1.5W / 3W
Dimming 0~10V dimming with remote dimmable driver (not included). See page 186-190 for Recommended Driver Chart.
Weight 0.78lbs (0.353kg).
Material Plated brass, anodized aluminum. RoHS compliant.
Mounting Vertically or horizontally positioned face plate mounts to single gang box (not included). Optimal mounting distance is 18 - 24 (457mm - 610mm) AFF.
Approval Dry locations. Approved to US and Canadian standards by CSA.
Note Can be used as emergency backup lighting in conjunction with Bodine emergency LED driver (sold separately). Consult factory.
50 See page 192 for explanation of symbols and Ip ratings.
Shown as 12 or 30 beam Vertical plate
Shown as 120 beam Vertical plate
Shown as 120 beam Horizontal plate
1 = 1W2 = 2.5W*
S = spot (12)N = narrow flood (30)W = wide flood (120)
W27S = 2700K, std CRIW30S = 3000K, std CRIW35S = 3500K, std CRIW41S = 4100K, std CRI W20H = 2000K, high CRIW30H = 3000K, high CRI
*only available in W30S & W20H.
NOTE: Standard CrI has a value of 75~82 while high CrI has 92.
W20H has consistent binning that falls within 1.5 MacAdam ellipse.
Lumen test results provided by Led chip manufacturer.
Image shows L14-1W30SWV-MC
7/8
1-1/2
3-1/4
3-1/8
4-3/4
1-3/835mm
22mm
38mm 79mm
83mm 121mm
1-1/238mm
5/816mm
7/8
1-1/2
3-1/4
3-1/8
4-3/4
1-3/835mm
22mm
38mm 79mm
83mm 121mm
1-1/238mm
5/816mm
7/8
1-1/2
3-1/4
3-1/8
4-3/4
1-3/835mm
22mm
38mm 79mm
83mm 121mm
1-1/238mm
5/816mm
approx. 35 cdmax.
0
180
90
45-45
-90
-0
-90
0.52.5
20
0.1 fc
Mount height: 1 ft Total LLF: 1
0
1
2
3
4
5
2 1 0 1 2 3
Isofootcandle PlotPolar Candela DistributionL141W, 1203000K Std85 lm
approx. 70 cdmax.
0
180
90
45-45
-90
-0
-90
0.5
2.5
20
0.1 fc
Mount height: 1 ft Total LLF: 1
0
1
2
3
4
5
2 1 0 1 2 3
Isofootcandle PlotPolar Candela DistributionL142.5W, 1203000K Std162 lm
27
26
Wall, Floor &
Ceiling Fixtureswww.mplighting.com
L14
Code WAttAge CoLor BeAM pLAte FINISH
L14 - -
V = verticalH = horizontal
MC = matte chromeBK = powder coated blackBN = brushed nickel
L14 1W / 2.5W Walkway
Application Indoor stair, ramp, aisle, and walkway illumination.
Source 1W, 350mA or 2.5W, 700mA LED
Driver Integral 120V primary, 3W 350mA (1W) or 9W 700mA (2.5W) non-dimmable driver.
Power Consumption 1.5W / 3W
Dimming 0~10V dimming with remote dimmable driver (not included). See page 186-190 for Recommended Driver Chart.
Weight 0.65lbs (0.296kg).
Material Plated brass, anodized aluminum. RoHS compliant.
Mounting Vertically or horizontally positioned face plate mounts to single gang box (not included). Optimal mounting distance is 18 - 24 (457mm - 610mm) AFF.
Approval Dry locations. Approved to US and Canadian standards by CSA.
Note Can be used as emergency backup lighting in conjunction with Bodine emergency LED driver (sold separately). Consult factory.
50 See page 192 for explanation of symbols and Ip ratings.
Shown as 12 or 30 beam Vertical plate
Shown as 120 beam Vertical plate
Shown as 120 beam Horizontal plate
1 = 1W2 = 2.5W*
S = spot (12)N = narrow flood (30)W = wide flood (120)
W27S = 2700K, std CRIW30S = 3000K, std CRIW35S = 3500K, std CRIW41S = 4100K, std CRI W20H = 2000K, high CRIW30H = 3000K, high CRI
*only available in W30S & W20H.
NOTE: Standard CrI has a value of 75~82 while high CrI has 92.
W20H has consistent binning that falls within 1.5 MacAdam ellipse.
Lumen test results provided by Led chip manufacturer.
Image shows L15-1W30SSW30SS-MC
7/8
1-1/2
1-3/835mm
2-1/854mm
1-5/841mm
22mm
38mm
3-1/4
3-1/8
4-3/4
79mm
83mm 121mm
1-1/238mm
7/8
1-1/2
1-3/835mm
2-1/854mm
1-5/841mm
22mm
38mm
3-1/4
3-1/8
4-3/4
79mm
83mm 121mm
1-1/238mm
approx. 750 cdmax.
0
180
90
45-45
-90
-0
-90
0.21.020
0.1 fc
Mount height: 1 ft Total LLF: 1
0
1
2
3
4
5
2 1 0 1 2 3
Isofootcandle PlotPolar Candela DistributionL152 x 1W, 123000K Std170 lm
approx. 1500 cdmax.
0
180
90
45-45
-90
-0
-90
0.52.520
0.1 fc
Mount height: 1 ft Total LLF: 1
0
1
2
3
4
5
2 1 0 1 2 3
Isofootcandle PlotPolar Candela DistributionL152 x 2.5W, 123000K Std324 lm
29
28
Wall, Floor &
Ceiling Fixtureswww.mplighting.com
L15
MC = matte chromeBK = powder coated blackBN = brushed nickel
L15 2 x 1W / 2.5W Up and Down Walkway
Application Indoor stair, ramp, aisle, and walkway illumination.
Source 2 x 1W, 350mA or 2 x 2.5W, 700mA LEDs.
Driver Integral 120V primary, 3W 350mA (2W) or 9W 700mA (5W) non-dimmable driver.
Power Consumption 3W / 6W
Dimming 0~10V dimming with remote dimmable driver (not included). See page 186-190 for Recommended Driver Chart.
Weight 1.03lbs (0.467kg).
Material Plated brass, anodized aluminum. RoHS compliant.
Mounting Vertically positioned face plate mounts to a single gang box (not included).
Approval Dry locations. Approved to US and Canadian standards by CSA.
Note Can be used as emergency backup lighting in conjunction with Bodine emergency LED driver (sold separately). Consult factory.
50 See page 192 for explanation of symbols and Ip ratings.
Shown as 12 or 30 beam
Shown as 120 beam
Code WAttAge CoLor up BeAM up CoLor doWN BeAM doWN FINISH
L15 - -
1 = 1W2 = 2.5W*
S = spot (12)N = narrow flood (30)W = wide flood (120)
S = spot (12)N = narrow flood (30)W = wide flood (120)
W27S = 2700K, std CRIW30S = 3000K, std CRIW35S = 3500K, std CRIW41S = 4100K, std CRI W20H = 2000K, high CRIW30H = 3000K, high CRI
W27S = 2700K, std CRIW30S = 3000K, std CRIW35S = 3500K, std CRIW41S = 4100K, std CRI W20H = 2000K, high CRIW30H = 3000K, high CRI
*only available in W30S & W20H.
NOTE: Standard CrI has a value of 75~82 while high CrI has 92.
W20H has consistent binning that falls within 1.5 MacAdam ellipse.
Lumen test results provided by Led chip manufacturer.
Image shows L16-1W30SWV-S6
1/83mm
1-1/829mm
3-3/886mm
5127mm
2-1/264mm
2-1/264mm
3-1/483mm
1/83mm
1-1/829mm
3-3/886mm
5127mm
2-1/264mm
2-1/264mm
3-1/483mm
approx. 275 cdmax.
-0
-90
0
180
90
45-45
-90
0.51020
0.1 fc
Mount height: 1 ft Total LLF: 1
0
1
2
3
4
5
2 1 0 1 2 3
Isofootcandle PlotPolar Candela DistributionL161W, 303000K Std85 lm
approx. 530 cdmax.
-0
-90
0
180
90
45-45
-90
0.52.520
0.1 fc
Mount height: 1 ft Total LLF: 1
0
1
2
3
4
5
2 1 0 1 2 3
Isofootcandle PlotPolar Candela DistributionL162.5W, 303000K Std162 lm
31
30
Wall, Floor &
Ceiling Fixtureswww.mplighting.com
L16
Code WAttAge CoLor BeAM pLAte FINISH
L16 - - S6
V = vertical H = horizontal
S6 = stainless steel 316
L16 1W / 2.5W Walkway
Application Outdoor / indoor wall, stair, and walkway illumination.
Source 1W, 350mA or 2.5W, 700mA LED
Driver Integral 120V primary, 3W 350mA (1W) or 9W 700mA (2.5W) non-dimmable driver.
Power Consumption 1.5W / 3W
Dimming 0~10V dimming with remote dimmable driver (not included). See page 186-190 for Recommended Driver Chart.
Weight 1.83lbs (0.832kg).
Material 316 stainless steel. RoHS compliant.
Mounting Vertically or horizontally positioned face plate mounts to a single gang box (not included). Optimal mounting distance is 18 - 24 (457mm - 610mm) AFF.
Approval Wet and dry locations. Approved to US and Canadian standards by CSA.
Note Can be used as emergency backup lighting in conjunction with Bodine emergency LED driver (sold separately). Consult factory.
66 See page 192 for explanation of symbols and Ip ratings.
Shown as Vertical plate
Shown as Horizontal plate
1 = 1W2 = 2.5W*
S = spot (12)N = narrow flood (30)W = wide flood (120)
W27S = 2700K, std CRIW30S = 3000K, std CRIW35S = 3500K, std CRIW41S = 4100K, std CRI W20H = 2000K, high CRIW30H = 3000K, high CRI
*only available in W30S & W20H.
NOTE: Standard CrI has a value of 75~82 while high CrI has 92.
W20H has consistent binning that falls within 1.5 MacAdam ellipse.
Lumen test results provided by Led chip manufacturer.
Image shows L17-1W30SNW30SW-S6
1/83mm
3-3/8
5
1-1/829mm
2-1/264mm
2-1/264mm
86mm
127mm
2-1/264mm
3-1/483mm
approx. 700 cdmax.
-0
-90
0
180
90
45-45
-90
0.51020
0.1 fc
Mount height: 1 ft Total LLF: 1
0
1
2
3
4
5
2 1 0 1 2 3
Isofootcandle PlotPolar Candela DistributionL172 x 1W, 123000K Std170 lm
approx. 1300 cdmax.
-0
-90
0
180
90
45-45
-90
0.55
20
0.1 fc
Mount height: 1 ft Total LLF: 1
0
1
2
3
4
5
2 1 0 1 2 3
Isofootcandle PlotPolar Candela DistributionL172 x 2.5W, 123000K Std324 lm
33
32
Wall, Floor &
Ceiling Fixtureswww.mplighting.com
L17
Code WAttAge CoLor up BeAM up CoLor doWN BeAM doWN FINISH
L17 - - S6
S6 = stainless steel 3161 = 1W2 = 2.5W*
L17 2 x 1W / 2.5W Up and Down Walkway
Application Outdoor / indoor wall, stair, and walkway illumination.
Source 2 x 1W, 350mA or 2 x 2.5W, 700mA LEDs.
Driver Integral 120V primary, 3W 350mA (2W) or 9W 700mA (5W) non-dimmable driver.
Power Consumption 3W / 6W
Dimming 0~10V dimming with remote dimmable driver (not included). See page 186-190 for Recommended Driver Chart.
Weight 3.06lbs (1.39kg).
Material 316 stainless steel. RoHS compliant.
Mounting Vertically positioned face plate mounts to a single gang box (not included).
Approval Wet and dry locations. Approved to US and Canadian standards by CSA.
Notes Can be used as emergency backup lighting in conjunction with Bodine emergency LED driver (sold separately). Consult factory.
66 See page 192 for explanation of symbols and Ip ratings.
S = spot (12)N = narrow flood (30)W = wide flood (120)
S = spot (12)N = narrow flood (30)W = wide flood (120)
W27S = 2700K, std CRIW30S = 3000K, std CRIW35S = 3500K, std CRIW41S = 4100K, std CRI W20H = 2000K, high CRIW30H = 3000K, high CRI
W27S = 2700K, std CRIW30S = 3000K, std CRIW35S = 3500K, std CRIW41S = 4100K, std CRI W20H = 2000K, high CRIW30H = 3000K, high CRI
*only available in W30S & W20H.
NOTE: Standard CrI has a value of 75~82 while high CrI has 92.
W20H has consistent binning that falls within 1.5 MacAdam ellipse.
Lumen test results provided by Led chip manufacturer.
Image shows L18-1W30SNV-S6
3-3/8
5
1-3/4
1-1/8
44mm
86mm
127mm
29mm
2-1/854mm
2-1/264mm
3-1/483mm
3-3/8
5
1-3/4
1-1/8
44mm
86mm
127mm
29mm
2-1/854mm
2-1/264mm
3-1/483mm
approx. 275 cdmax.
-0
-90
0
180
90
45-45
-90
0.51020
0.1 fc
Mount height: 1 ft Total LLF: 1
0
1
2
3
4
5
2 1 0 1 2 3
Isofootcandle PlotPolar Candela DistributionL181W, 303000K Std85 lm
approx. 530 cdmax.
-0
-90
0
180
90
45-45
-90
0.52.520
0.1 fc
Mount height: 1 ft Total LLF: 1
0
1
2
3
4
5
2 1 0 1 2 3
Isofootcandle PlotPolar Candela DistributionL182.5W, 303000K Std162 lm
35
34
Wall, Floor &
Ceiling Fixtureswww.mplighting.com
L18 1W / 2.5W Walkway
Application Outdoor / indoor wall, stair, and walkway illumination.
Source 1W, 350mA or 2.5W, 700mA LED
Driver Integral 120V primary, 3W 350mA (1W) or 9W 700mA (2.5W) non-dimmable driver.
Power Consumption 1.5W / 3W
Dimming 0~10V dimming with remote dimmable driver (not included). See page 186-190 for Recommended Driver Chart.
Weight 1.92lbs (0.873kg).
Material 316 stainless steel. RoHS compliant.
Mounting Vertically or horizontally positioned face plate mounts to a single gang box (not included). Optimal mounting distance is 18 - 24 (457mm - 610mm) AFF.
Approval Wet and dry locations. Approved to US and Canadian standards by CSA.
Notes Can be used as emergency backup lighting in conjunction with Bodine emergency LED driver (sold separately). Consult factory.
66 See page 192 for explanation of symbols and Ip ratings.
L18
Code WAttAge CoLor BeAM pLAte FINISH
L18 - - S6
V = vertical H = horizontal
1 = 1W 2 = 2.5W*
S6 = stainless steel 316
Shown as Vertical plate
Shown as Horizontal plate
S = spot (12)N = narrow flood (30)W = wide flood (120)
W27S = 2700K, std CRIW30S = 3000K, std CRIW35S = 3500K, std CRIW41S = 4100K, std CRI W20H = 2000K, high CRIW30H = 3000K, high CRI
*only available in W30S & W20H.
NOTE: Standard CrI has a value of 75~82 while high CrI has 92.
W20H has consistent binning that falls within 1.5 MacAdam ellipse.
Lumen test results provided by Led chip manufacturer.
Image shows L19-1W30SNW30SN-S6
3-3/8
5
86mm
127mm
1/8 1-1/83mm 29mm
2-1/264mm
2-1/264mm
3-1/483mm
2-1/854mm
approx. 28 cdmax.
-0
-90
0
180
90
45-45
-90
12.520
0.1 fc
Mount height: 1 ft Total LLF: 1
0
1
2
3
4
5
2 1 0 1 2 3
Isofootcandle PlotPolar Candela DistributionL192 x 1W, 1203000K Std170 lm
approx. 55 cdmax.
-0
-90
0
180
90
45-45
-90
1
520
0.1 fc
Mount height: 1 ft Total LLF: 1
0
1
2
3
4
5
2 1 0 1 2 3
Isofootcandle PlotPolar Candela DistributionL192 x 2.5W, 1203000K Std324 lm
37
36
Wall, Floor &
Ceiling Fixtureswww.mplighting.com
L19 2 x 1W / 2.5W Up and Down Walkway
Application Outdoor / indoor wall, stair, and walkway illumination.
Source 2 x 1W, 350mA or 2 x 2.5W, 700mA LEDs.
Driver Integral 120V primary, 3W 350mA (2W) or 9W 700mA (5W) non-dimmable driver.
Power Consumption 3W / 6W
Dimming 0~10V dimming with remote dimmable driver (not included). See page 186-190 for Recommended Driver Chart.
Weight 3.24lbs (1.47kg).
Material 316 stainless steel. RoHS compliant.
Mounting Vertically positioned face plate mounts to a single gang box (not included).
Approval Wet and dry locations. Approved to US and Canadian standards by CSA.
Notes Can be used as emergency backup lighting in conjunction with Bodine emergency LED driver (sold separately). Consult factory.
66 See page 192 for explanation of symbols and Ip ratings.
L19
Code WAttAge CoLor up BeAM up CoLor doWN BeAM doWN FINISH
L19 - - S6
S = stainless steel 3161 = 1W2 = 2.5W*
S = spot (12)N = narrow flood (30)W = wide flood (120)
S = spot (12)N = narrow flood (30)W = wide flood (120)
W27S = 2700K, std CRIW30S = 3000K, std CRIW35S = 3500K, std CRIW41S = 4100K, std CRI W20H = 2000K, high CRIW30H = 3000K, high CRI
W27S = 2700K, std CRIW30S = 3000K, std CRIW35S = 3500K, std CRIW41S = 4100K, std CRI W20H = 2000K, high CRIW30H = 3000K, high CRI
*only available in W30S & W20H.
NOTE: Standard CrI has a value of 75~82 while high CrI has 92.
W20H has consistent binning that falls within 1.5 MacAdam ellipse.
Lumen test results provided by Led chip manufacturer.
Image shows L21-1W30SF-S3
1-3/8
3-1/2 2-1/264mm
19mm
89mm
35mm
3/4
4-5/8117mm
1/46mm
approx. 4 cdmax.
-0
-90
0
180
90
45
135
-90
0.2
0.5
1 0.1 fc
Mount height: 1 ft Total LLF: 1
432
10123
4
0 1 2 3 4 5 6 7 8
Isofootcandle PlotPolar Candela DistributionL211W3000K Std85 lm
approx. 7.5 cdmax.
-0
-90
0
180
90
45
135
-90
0.2
0.5
2.5 0.1 fc
Mount height: 1 ft Total LLF: 1
432
10123
4
0 1 2 3 4 5 6 7 8
Isofootcandle PlotPolar Candela DistributionL212.5W3000K Std162 lm
39
38
Wall, Floor &
Ceiling Fixtureswww.mplighting.com
L21
Code WAttAge CoLor LeNS FINISH
L21 - F - S3
F = frosted S3 = stainless steel 303
L21 1W / 2.5W Walkway
Application Indoor stair, ramp, aisle, and walkway illumination.
Source 1W, 350mA or 2.5W, 700mA LED
Driver Integral 120V primary, 3W 350mA (1W) or 3W 700mA (2.5W) non-dimmable driver.
Power Consumption 1.5W / 3W
Dimming 0~10V dimming with remote dimmable driver (not included). See page 186-190 for Recommended Driver Chart.
Weight 0.99lbs (0.45kg).
Material 303 stainless steel and polycarbonate lens. RoHS compliant.
Mounting Mounts to standard 4 (102mm) octagonal box (1-1/2 / 38mm minimum depth). Optimal mounting distance is 18 - 24 (457mm - 610mm) AFF.
Approval Dry locations. Approved to US and Canadian standards by CSA.
Note Can be used as emergency backup lighting in conjunction with Bodine emergency LED driver (sold separately). Consult factory.
50 See page 192 for explanation of symbols and Ip ratings.
1 = 1W2 = 2.5W*
W27S = 2700K, std CRIW30S = 3000K, std CRIW35S = 3500K, std CRIW41S = 4100K, std CRI W20H = 2000K, high CRIW30H = 3000K, high CRI
*only available in W30S & W20H.
NOTE: Standard CrI has a value of 75~82 while high CrI has 92.
W20H has consistent binning that falls within 1.5 MacAdam ellipse.
Lumen test results provided by Led chip manufacturer.
Image shows L22-1W30SF-S3
3-1/2 4-5/8117mm
2-1/264mm
19mm
89mm
3/4
1/46mm1-3/4
44mm
approx. 4 cdmax.
-0
-90
0
180
90
45
135
-90
0.2
0.5
1 0.1 fc
Mount height: 1 ft Total LLF: 1
432
10123
4
0 1 2 3 4 5 6 7 8
Isofootcandle PlotPolar Candela DistributionL221W3000K Std85 lm
approx. 7.5 cdmax.
-0
-90
0
180
90
45
135
-90
0.2
0.5
2.5 0.1 fc
Mount height: 1 ft Total LLF: 1
432
10123
4
0 1 2 3 4 5 6 7 8
Isofootcandle PlotPolar Candela DistributionL222.5W3000K Std162 lm
41
40
Wall, Floor &
Ceiling Fixtureswww.mplighting.com
L22
L22 1W / 2.5W Walkway
Application Outdoor / indoor wall, stair, and walkway illumination.
Source 1W, 350mA or 2.5W, 700mA LED
Driver Integral 120V primary, 3W 350mA (1W) or 3W 700mA (2.5W) non-dimmable driver.
Power Consumption 1.5W / 3W
Dimming 0~10V dimming with remote dimmable driver (not included). See page 186-190 for Recommended Driver Chart.
Weight 0.99lbs (0.45kg).
Material 303 stainless steel and polycarbonate lens. RoHS compliant.
Mounting Mounts to standard 4 (102mm) octagonal box (1-1/2 / 38mm minimum depth). Use outdoor rated box for outdoor applications. Optimal mounting distance is 18-24 (457mm-610mm) AFF.
Approval Wet locations. Approved to US and Canadian standards by CSA.
Note Can be used as emergency backup lighting in conjunction with Bodine emergency LED driver (sold separately). Consult factory.
66 See page 192 for explanation of symbols and Ip ratings.
Code WAttAge CoLor LeNS FINISH
L22 - F - S3
F = frosted S3 = stainless steel 3031 = 1W2 = 2.5W*
W27S = 2700K, std CRIW30S = 3000K, std CRIW35S = 3500K, std CRIW41S = 4100K, std CRI W20H = 2000K, high CRIW30H = 3000K, high CRI
*only available in W30S & W20H.
NOTE: Standard CrI has a value of 75~82 while high CrI has 92.
W20H has consistent binning that falls within 1.5 MacAdam ellipse.
Lumen test results provided by Led chip manufacturer.
Image shows L31-1W30S-MC
7/8
4-5/83-1/4
3-1/879mm
83mm
3-1/483mm
117mm
22mm
125mm
7/8
4-5/83-1/4
3-1/879mm
83mm
3-1/483mm
117mm
22mm
125mm
approx. 25 cdmax.
-0
-90
0
180
90
45
135
-90 5
Mount height: 1 ft Total LLF: 1
432
10123
4
0 1 2 3 4 5 6 7 8
0.1 fc0.52.50.2
Isofootcandle PlotPolar Candela DistributionL311W, 303000K Std85 lm
approx. 48 cdmax.
-0
-90
0
180
90
45
135
-90 5
Mount height: 1 ft Total LLF: 1
432
10123
4
0 1 2 3 4 5 6 7 8
0.1 fc15 0.2
Isofootcandle PlotPolar Candela DistributionL312.5W, 303000K Std162 lm
43
42
Wall, Floor &
Ceiling Fixtureswww.mplighting.com
L31
Code WAttAge CoLor FINISH
L31 - -
MC = matte chromeS3 = stainless steel 303
L31 1W / 2.5W Walkway
Application Indoor stair, ramp, aisle, and walkway illumination.
Source 1W, 350mA or 2.5W, 700mA LED
Driver Integral 120V primary, 3W 350mA (1W) or 3W 700mA (2.5W) non-dimmable driver.
Power Consumption 1.5W / 3W
Dimming 0~10V dimming with remote dimmable driver (not included). See page 186-190 for Recommended Driver Chart.
Weight 0.57lbs (0.258kg).
Material Plated brass and polycarbonate cylinder lens. RoHS compliant.
Mounting Vertically or horizontally positioned face plate mounts to a single gang box (not included).
Approval Dry locations. Approved to US and Canadian standards by CSA.
Note Can be used as emergency backup lighting in conjunction with Bodine emergency LED driver (sold separately). Consult factory.
50 See page 192 for explanation of symbols and Ip ratings.
Shown as Vertical plate
Shown as Horizontal plate
1 = 1W2 = 2.5W*
W27S = 2700K, std CRIW30S = 3000K, std CRIW35S = 3500K, std CRIW41S = 4100K, std CRI W20H = 2000K, high CRIW30H = 3000K, high CRI
*only available in W30S & W20H.
NOTE: Standard CrI has a value of 75~82 while high CrI has 92.
W20H has consistent binning that falls within 1.5 MacAdam ellipse.
Lumen test results provided by Led chip manufacturer.
Image shows L32-1W30S-MC
7/8
1 Sq.25mm Sq.
3-1/879mm
4-5/8117mm
3-1/483mm
3-1/483mm
22mm7/8
1 Sq.25mm Sq.
3-1/879mm
4-5/8117mm
3-1/483mm
3-1/483mm
22mm
approx. 27 cdmax.
-0
-90
0
180
90
45
135
-90 0.1 fc0.52.50.2
Mount height: 1 ft Total LLF: 1
432
10123
4
0 1 2 3 4 5 6 7 8
Isofootcandle PlotPolar Candela DistributionL321W, 303000K Std85 lm
approx. 52 cdmax.
-0
-90
0
180
90
45
135
-90 0.1 fc15 0.2
Mount height: 1 ft Total LLF: 1
432
10123
4
0 1 2 3 4 5 6 7 8
Isofootcandle PlotPolar Candela DistributionL322.5W, 303000K Std162 lm
45
44
Wall, Floor &
Ceiling Fixtureswww.mplighting.com
L32
Code WAttAge CoLor FINISH
L32 - -
L32 1W / 2.5W Walkway
Application Indoor stair, ramp, aisle, and walkway illumination.
Source 1W, 350mA or 2.5W, 700mA LED
Driver Integral 120V primary, 3W 350mA (1W) or 3W 700mA (2.5W) non-dimmable driver.
Power Consumption 1.5W / 3W
Dimming 0~10V dimming with remote dimmable driver (not included). See page 186-190 for Recommended Driver Chart.
Weight 0.57lbs (0.258kg).
Material Plated brass and polycarbonate cube lens. RoHS compliant.
Mounting Vertically or horizontally positioned face plate mounts to a single gang box (not included).
Approval Dry locations. Approved to US and Canadian standards by CSA.
Note Can be used as emergency backup lighting in conjunction with Bodine emergency LED driver (sold separately). Consult factory.
50 See page 192 for explanation of symbols and Ip ratings.
Shown as Vertical plate
Shown as Horizontal plate
MC = matte chromeS3 = stainless steel 303
1 = 1W2 = 2.5W*
W27S = 2700K, std CRIW30S = 3000K, std CRIW35S = 3500K, std CRIW41S = 4100K, std CRI W20H = 2000K, high CRIW30H = 3000K, high CRI
*only available in W30S & W20H.
NOTE: Standard CrI has a value of 75~82 while high CrI has 92.
W20H has consistent binning that falls within 1.5 MacAdam ellipse.
Lumen test results provided by Led chip manufacturer.
Image shows L33-1W30S-S6
125mm
3-1/483mm
4-5/8117mm
1-3/444mm
3-1/483mm
7/822mm
125mm
3-1/483mm
4-5/8117mm
1-3/444mm
3-1/483mm
7/822mm
approx. 25 cdmax.
-0
-90
0
180
90
45
135
-90 5
Mount height: 1 ft Total LLF: 1
432
10123
4
0 1 2 3 4 5 6 7 8
0.1 fc0.52.50.2
Isofootcandle PlotPolar Candela DistributionL331W, 303000K Std85 lm
approx. 48 cdmax.
-0
-90
0
180
90
45
135
-90 5
Mount height: 1 ft Total LLF: 1
432
10123
4
0 1 2 3 4 5 6 7 8
0.1 fc15 0.2
Isofootcandle PlotPolar Candela DistributionL332.5W, 303000K Std162 lm
47
46
Wall, Floor &
Ceiling Fixtureswww.mplighting.com
L33
Code WAttAge CoLor FINISH
L33 - - S6
L33 1W / 2.5W Walkway
Application Outdoor / indoor wall, stair, and walkway illumination.
Source 1W, 350mA or 2.5W, 700mA LED
Driver Integral 120V primary, 3W 350mA (1W) or 9W 700mA (2.5W) non-dimmable driver.
Power Consumption 1.5W / 3W
Dimming 0~10V dimming with remote dimmable driver (not included). See page 186-190 for Recommended Driver Chart.
Weight 1.34lbs (0.609kg).
Material 316 stainless steel and polycarbonate cylinder lens. RoHS compliant.
Mounting Vertically or horizontally positioned face plate mounts to a single gang box (not included).
Approval Wet locations. Approved to US and Canadian standards by CSA.
Note Can be used as emergency backup lighting in conjunction with Bodine emergency LED driver (sold separately). Consult factory.
66 See page 192 for explanation of symbols and Ip ratings.
Shown as Vertical plate
Shown as Horizontal plate
S6 = stainless steel 3161 = 1W2 = 2.5W*
W27S = 2700K, std CRIW30S = 3000K, std CRIW35S = 3500K, std CRIW41S = 4100K, std CRI W20H = 2000K, high CRIW30H = 3000K, high CRI
*only available in W30S & W20H.
NOTE: Standard CrI has a value of 75~82 while high CrI has 92.
W20H has consistent binning that falls within 1.5 MacAdam ellipse.
Lumen test results provided by Led chip manufacturer.
Image shows L34-1W30S-S6
1 Sq.25mm Sq.
3-1/483mm7/8
3-1/483mm
1-3/444mm
22mm
4-5/8117mm
1 Sq.25mm Sq.
3-1/483mm7/8
3-1/483mm
1-3/444mm
22mm
4-5/8117mm
approx. 27 cdmax.
-0
-90
0
180
90
45
135
-90 0.1 fc0.52.50.2
Mount height: 1 ft Total LLF: 1
432
10123
4
0 1 2 3 4 5 6 7 8
Isofootcandle PlotPolar Candela DistributionL341W, 303000K Std85 lm
approx. 52 cdmax.
-0
-90
0
180
90
45
135
-90 0.1 fc15 0.2
Mount height: 1 ft Total LLF: 1
432
10123
4
0 1 2 3 4 5 6 7 8
Isofootcandle PlotPolar Candela DistributionL342.5W, 303000K Std162 lm
49
48
Wall, Floor &
Ceiling Fixtureswww.mplighting.com
L34
Code WAttAge CoLor FINISH
L34 - - S6
L34 1W / 2.5W Walkway
Application Outdoor / indoor wall, stair, and walkway illumination.
Source 1W, 350mA or 2.5W, 700mA LED
Driver Integral 120V primary, 3W 350mA (1W) or 9W 700mA (2.5W) non-dimmable driver.
Power Consumption 1.5W / 3W
Dimming 0~10V dimming with remote dimmable driver (not included). See page 186-190 for Recommended Driver Chart.
Weight 1.34lbs (0.609kg).
Material 316 stainless steel and polycarbonate cube lens. RoHS compliant.
Mounting Vertically or horizontally positioned face plate mounts to a single gang box (not included).
Approval Wet locations. Approved to US and Canadian standards by CSA.
Note Can be used as emergency backup lighting in conjunction with Bodine emergency LED driver (sold separately). Consult factory.
66 See page 192 for explanation of symbols and Ip ratings.
Shown as Vertical plate
Shown as Horizontal plate
S6 = stainless steel 3161 = 1W2 = 2.5W*
W27S = 2700K, std CRIW30S = 3000K, std CRIW35S = 3500K, std CRIW41S = 4100K, std CRI W20H = 2000K, high CRIW30H = 3000K, high CRI
*only available in W30S & W20H.
NOTE: Standard CrI has a value of 75~82 while high CrI has 92.
W20H has consistent binning that falls within 1.5 MacAdam ellipse.
Lumen test results provided by Led chip manufacturer.
Image shows L35-3W30S-MA
3/8
4-3/43-1/4
1-3/4
2-3/860mm
45mm
83mm
3-1/483mm
121mm
10mm3/8
4-3/43-1/4
1-3/4
2-3/860mm
45mm
83mm
3-1/483mm
121mm
10mm
approx. 70 cdmax.
-0
-90
0
180
90
45
135
-90 0.1 fc0.5
Mount height: 1 ft Total LLF: 1
4
2
0
2
4
6
0 2 4 6 8 10
2.510
Isofootcandle PlotPolar Candela DistributionL353.5W3000K Std250 lm
approx. 140 cdmax.
-0
-90
0
180
90
45
135
-90 0.1 fc0.51520
Mount height: 1 ft Total LLF: 1
4
2
0
2
4
6
0 2 4 6 8 10
Isofootcandle PlotPolar Candela DistributionL356.5W3000K Std475 lm
51
50
Wall, Floor &
Ceiling Fixtureswww.mplighting.com
L35
Code WAttAge CoLor FINISH
L35 - W30S -
3 = 3.5W6 = 6.5W
W30S = 3000K, std CRI MA = matte clear anodizedBA = black anodized
L35 3.5W / 6.5W Walkway
Application Outdoor / indoor wall, stair, and walkway illumination.
Source 3.5W, 350mA or 6.5W, 700mA LED
Driver Integral 120V primary, 3W 350mA (3.5W) or 9W 700mA (6.5W) non-dimmable driver.
Power Consumption 4W / 8W
Dimming 0~10V dimming with remote dimmable driver (not included). See page 186-190 for Recommended Driver Chart.
Weight 1.18lbs (0.537kg).
Material Anodized aluminum and polycarbonate lens. RoHS compliant.
Mounting Face plate mounts vertically or horizontally to a single gang box (not included).
Approval Wet and dry locations. Approved to US and Canadian standards by CSA.
Notes Can be used as emergency backup lighting in conjunction with Bodine emergency LED driver (sold separately). Consult factory.
66 See page 192 for explanation of symbols and Ip ratings.
Shown as Vertical plate
Shown as Horizontal plate
NOTE: Standard CrI has a value of 75~82.
Lumen test results provided by Led chip manufacturer.
Image shows L36-3W30S-MA
3/810mm
5/816mm
1-7/848mm
1/46mm
45
3-1/4
2-3/860mm
3-1/483mm
83mm
4-3/4121mm
approx. 33 cdmax.
-0
-90
0
180
90
45
135
-90 0.1 fc0.5510
Mount height: 1 ft Total LLF: 1
432
10123
4
0 1 2 3 4 5 6 7 8
Isofootcandle PlotPolar Candela DistributionL363.5W3000K Std250 lm
approx. 65 cdmax.
-0
-90
0
180
90
45
135
-90 0.1 fc0.51020
Mount height: 1 ft Total LLF: 1
432
10123
4
0 1 2 3 4 5 6 7 8
Isofootcandle PlotPolar Candela DistributionL366.5W3000K Std475 lm
53
52
Wall, Floor &
Ceiling Fixtureswww.mplighting.com
L36
Code WAttAge CoLor FINISH
L36 - W30S -
3 = 3.5W6 = 6.5W
W30S = 3000K, std CRI MA = matte clear anodizedBA = black anodized
L36 3.5W / 6.5W Walkway
Application Outdoor / indoor wall, stair, and walkway illumination.
Source 3.5W, 350mA or 6.5W, 700mA LED
Driver Integral 120V primary, 3W 350mA (3.5W) or 9W 700mA (6.5W) non-dimmable driver.
Power Consumption 4W / 8W
Dimming 0~10V dimming with remote dimmable driver (not included). See page 186-190 for Recommended Driver Chart.
Weight 1.4lbs (0.636kg).
Material Anodized aluminum and polycarbonate lens. RoHS compliant.
Mounting Face plate mounts horizontally to single gang box (not included).
Approval Wet and dry locations. Approved to US and Canadian standards by CSA.
Notes Can be used as emergency backup lighting in conjunction with Bodine emergency LED driver (sold separately). Consult factory.
66 See page 192 for explanation of symbols and Ip ratings.
NOTE: Standard CrI has a value of 75~82.
Lumen test results provided by Led chip manufacturer.
Image shows L37-3W30S-MA
7/822mm
1-1/829mm
251mm
1/46mm
45 2-3/860mm
2-3/470mm
4-1/2114mm
approx. 33 cdmax.
-0
-90
0
180
90
45
135
-90 0.1 fc0.5510
Mount height: 1 ft Total LLF: 1
432
10123
4
0 1 2 3 4 5 6 7 8
Isofootcandle PlotPolar Candela DistributionL373.5W3000K Std250 lm
approx. 65 cdmax.
-0
-90
0
180
90
45
135
-90 0.1 fc0.51020
Mount height: 1 ft Total LLF: 1
432
10123
4
0 1 2 3 4 5 6 7 8
Isofootcandle PlotPolar Candela DistributionL376.5W3000K Std475 lm
55
54
Wall, Floor &
Ceiling Fixtureswww.mplighting.com
L37
Code WAttAge CoLor FINISH
L37 - W30S -
3 = 3.5W6 = 6.5W
W30S = 3000K, std CRI MA = matte clear anodizedBA = black anodized
L37 3.5W / 6.5W Walkway
Application Outdoor / indoor wall, stair, and walkway illumination.
Source 3.5W, 350mA or 6.5W, 700mA LED
Driver Integral 120V primary, 3W 350mA (3.5W) or 9W 700mA (6.5W) non-dimmable driver.
Power Consumption 4W / 8W
Dimming 0~10V dimming with remote dimmable driver (not included). See page 186-190 for Recommended Driver Chart.
Weight 2.19lbs (0.994kg).
Material Anodized aluminum and polycarbonate lens. RoHS compliant.
Mounting Mounts to standard 4 (102mm) octagonal box (1-1/2 / 38mm minimum depth). Use outdoor rated box for outdoor applications. Optimal mounting distance is 18-24 (457mm-610mm) AFF.
Approval Wet and dry locations. Approved to US and Canadian standards by CSA.
Note Can be used as emergency backup lighting in conjunction with Bodine emergency LED driver (sold separately). Consult factory.
66 See page 192 for explanation of symbols and Ip ratings.
NOTE: Standard CrI has a value of 75~82.
Lumen test results provided by Led chip manufacturer.
Image shows L91-2W30SNC0-MA
3-7/8
3-3/8
3-1/4
4-1/2 Sq.
86mm
98mm 114mm Sq.
83mm2-5/867mm
approx. 1350 cdmax.
-0
-90
0
180
90
45-45
-90520
0.1 fc
Mount height: 6 ft Total LLF: 1
0
1
2
1 0 1
0.5
Isofootcandle PlotPolar Candela DistributionL9112, clear lens3000K Std162 lm
approx. 550 cdmax.
0
180
90
45-45
-90
-0
-90
2.510
0.1 fc0.5
Mount height: 6 ft Total LLF: 1
0
1
2
1 0 1
Isofootcandle PlotPolar Candela DistributionL9130, clear lens3000K Std162 lm
3-7/8
3-3/8
3-1/4
4-1/2 Sq.
86mm
98mm 114mm Sq.
83mm2-5/867mm
57
56
Wall, Floor &
Ceiling Fixtureswww.mplighting.com
L91
Code WAttAge CoLor BeAM LeNS ANgLe BrACket FINISH
L91 - 2 - MA
2 = 2.5W W30S = 3000K, std CRIW20H = 2000K, high CRI
S = spot (12)N = narrow flood (30)W = wide flood (120)
C = clearF = frosted
0 = no angle 30 = 30 angle X = custom (30 max.)
MA = matte clear anodized
L91 2.5W Downlight
Application Outdoor / indoor wall mounted for up or down illumination.
Source 2.5W LED
Driver Integral 120V primary, 3W 700mA non-dimmable driver.
Power Consumption 3W
Dimming 0~10V dimming with remote dimmable driver (not included). See page 186-190 for Recommended Driver Chart.
Weight 2.02lbs (0.914kg)
Material Anodized aluminum, insert trim with 1/4 (6mm) thick tempered glass lens. RoHS compliant.
Mounting Mounts to standard 4 (102mm) octagonal box (1-1/2/ 38mm minimum depth). Can be positioned facing up or down.
Approval Wet and dry locations. Approved to US and Canadian standards by CSA.
Note Can be used as emergency backup lighting in conjunction with Bodine emergency LED driver (sold separately). Consult factory.
66 See page 192 for explanation of symbols and Ip ratings.
Shown with no angle bracket
Shown with angle bracket
NOTE: Standard CrI has a value of 75~82 while high CrI has 92.
W20H has consistent binning that falls within 1.5 MacAdam ellipse.
Lumen test results provided by Led chip manufacturer.
Image shows L92-2W30SNC0-24MA
2-3/8
3-7/8
4-1/2 6 Sq.
1/4
98mm
60mm2-3/860mm
6mm
114mm 152mm Sq.
7-3/8187mm
5-1/2140mm 2-5/867mm
H (post height)
1-3/444mm
3/419mm
approx. 500 cdmax.
-0
-90
0
180
90
45-45
-90
0.1 fc
20 5
0.5
Mount height: 3 ft Total LLF: 1
2
1
1
0
2
1 0 1
Isofootcandle PlotPolar Candela DistributionL9230, clear lens3000K Std162 lm
approx. 55 cdmax.
-0
-90
0
180
90
45-45
-90
2.5
0.1 fc
20
1 0.5
Mount height: 3 ft Total LLF: 1
2
1
1
0
2
1 0 1
Isofootcandle PlotPolar Candela DistributionL92120, clear lens3000K Std162 lm
59
58
Wall, Floor &
Ceiling Fixtureswww.mplighting.com
L92
Code WAttAge CoLor BeAM LeNS ANgLe BrACket poSt HeIgHt (H) FINISH
L92 - 2 - MA
2 = 2.5W C = clearF = frosted
0 = no angle 30 = 30 angle X = custom (30 max.)
24 = 24 (610mm)36 = 36 (914mm) 48 = 48 (1219mm)
MA = matte clear anodized
L92 2.5W Bollard
Application Outdoor walkway and area illumination.
Source 2.5W LED
Driver Integral 120V primary, 3W 700mA non-dimmable driver.
Power Consumption 3W
Dimming 0~10V dimming with remote dimmable driver (not included). See page 186-190 for Recommended Driver Chart.
Weight 7.15lbs (3.245kg) based on 24 (610mm) post.
Material Anodized aluminum, insert trim with 1/4 (6mm) thick tempered glass lens. RoHS compliant.
Mounting Mounts to 24 (610mm), 36 (614mm) or 48 (1219mm) anodized aluminum post. Comes with 24 (610mm) Cabtire lead inside post.
Approval Wet and dry locations. Approved to US and Canadian standards by CSA.
Note Can be used as emergency backup lighting in conjunction with Bodine emergency LED driver (sold separately). Consult factory.
66 See page 192 for explanation of symbols and Ip ratings.
Shown with angle bracket
Shown with no angle bracket
W30S = 3000K, std CRIW20H = 2000K, high CRI
NOTE: Standard CrI has a value of 75~82 while high CrI has 92.
W20H has consistent binning that falls within 1.5 MacAdam ellipse.
S = spot (12)N = narrow flood (30)W = wide flood (120)
Lumen test results provided by Led chip manufacturer.
Image shows L97-1W30SN-36MA
5-3/8137mm
4-1/2114mm
6152mm
1/46mm
Post Height
8-1/2216mm
1-5/841mm
6-3/8162mm
5-3/8 x 6-3/8137mm x 162mm
4-1/2114mm 6 Sq.
152mm Sq.
1/46mm
Post Height
8-1/2216mm
1-5/841mm
approx. 1300 cdmax.
-0
-90
0
180
90
45-45
-90
0.1 fc0.50.2
2.520
Mount height: 3 ft Total LLF: 1
2
1
1
0
2
1 0 1
Isofootcandle PlotPolar Candela DistributionL976 x 1W, 303000K Std510 lm
approx. 1300 cdmax.
-0
-90
0
180
90
45-45
-90
0.1 fc0.50.2
2.520
Mount height: 3 ft Total LLF: 1
2
1
1
0
2
1 0 1
Isofootcandle PlotPolar Candela DistributionL976 x 1W, 303000K Std510 lm
approx. 520 cdmax.
-0
-90
0
180
90
45-45
-90
0.1 fc
2010 2.5
0.5
Mount height: 3 ft Total LLF: 1
3
1
1
2
2
0
3
12 20 1
Isofootcandle PlotPolar Candela DistributionL97E6 x 2.5W3000K Std630 lm
approx. 520 cdmax.
-0
-90
0
180
90
45-45
-90
0.1 fc
2010 2.5
0.5
Mount height: 3 ft Total LLF: 1
3
1
1
2
2
0
3
12 20 1
Isofootcandle PlotPolar Candela DistributionL97E6 x 2.5W3000K Std630 lm
61
60
Wall, Floor &
Ceiling Fixtureswww.mplighting.com
Code WAttAge CoLor BeAM poSt HeIgHt (H) FINISH
L97 - -
W27S = 2700K, std CRIW30S = 3000K, std CRIW35S = 3500K, std CRIW41S = 4100K, std CRI W20H = 2000K, high CRIW30H = 3000K, high CRI
1 = 6 x 1W2 = 6 x 2.5W*
MA = matte clear anodizedBA = black anodized
L97 6W/15W Bollard / L97E 14W Bollard
Application Outdoor walkway and area illumination.
Source L97: 6 x 1W, 350mA or 6 x 2.5W, 700mA LEDs L97E: 6 x 2.5W, 700mA LEDs
Driver L97: Remote 120V primary, 350mA (6W) or 700mA (15W) driver (not included) L97E: Remote 120V primary, 700mA driver (not included)
LED Input Voltage 24V DC
Power Consumption L97: 8W / 18W L97E: 18W
Dimming Dimmable with dimming controller, 0~10V dimming (not included). See page 186-190 for Recommended Driver Chart.
Weight 9.59lbs (4.35kg) based on 36 (914mm) post.
Material Anodized aluminum. 1/4 (6mm) thick polycarbonate lens and silicone gaskets. RoHS compliant.
Mounting Mounts to 36 (914mm) or 48 (1219mm) anodized aluminum post. Comes with 24 (610mm) Cabtire lead inside post.
Approval Wet and dry locations. Approved to US and Canadian standards by CSA.
Notes An appropriate 24V DC LED driver must be used with fixture. Can be used as emergency backup lighting in conjunction with Bodine emergency LED driver (sold separately). Consult factory.
67 See page 192 for explanation of symbols and Ip ratings.
L97
36 = 36 (914mm) 48 = 48 (1219mm)
*only available in W30S & W20H.
NOTE: Standard CrI has a value of 75~82 while high CrI has 92.
W20H has consistent binning that falls within 1.5 MacAdam ellipse.
Code LIgHt dIStrIButIoN WAttAge CoLor poSt HeIgHt (H) FINISH
L97 E - 2 -
W27S = 2700K, std CRIW30S = 3000K, std CRIW35S = 3500K, std CRIW41S = 4100K, std CRIW20H = 2000K, high CRI W30H = 3000K, high CRI
2 = 6 x 2.5WE = elliptical light distribution MA = matte clear anodizedBA = black anodized
36 = 36 (914mm) 48 = 48 (1219mm)
S = spot (12)N = narrow flood (30)F = flood (60)
Lumen test results provided by Led chip manufacturer.
Image shows L98-1W30SN-6MA
3-1/4
5-3/8
4-3/81/8
1-5/8
5-3/4
6
3mm
152mm
111mm
41mm
146mm
83mm
137mm
approx. 2700 cdmax.
-0
-90
0
180
90
45-45
-90
0.1 fc520
0.5
Mount height: 9 ft Total LLF: 1
0
1
2
1 1 20
Isofootcandle PlotPolar Candela DistributionL986 x 1W, 123000K Std510 lm
approx. 6000 cdmax.
-0
-90
0
180
90
45-45
-90
0.1 fc120
0.2
Mount height: 9 ft Total LLF: 1
0
1
2
1 1 20
Isofootcandle PlotPolar Candela DistributionL986 x 2.5W, 123000K Std972 lm
63
62
Wall, Floor &
Ceiling Fixtureswww.mplighting.com
L98
Code WAttAge CoLor BeAM LeAd LeNgtH FINISH
L98 - -
6 = 6 (1829mm)X = custom
1 = 6 x 1W2 = 6 x 2.5W*
MA = matte clear anodizedBA = black anodizedS6 = stainless steel 316
L98 6W/15W LED Wall Sconce
Application Outdoor / indoor wall mounted for up or down illumination.
Source 6 x 1W, 350mA or 6 x 2.5W, 700mA LEDs
Driver Remote 120V primary, 350mA (6W) or 700mA (15W) driver (not included).
LED Input Voltage 24V DC
Power Consumption 8W / 18W
Dimming Dimmable with dimming controller, 0~10V dimming (not included). See page 186-190 for Recommended Driver Chart.
Weight 2.24lbs (1.54kg).
Material Anodized aluminum or 316 stainless steel. 1/4 (6mm) thick polycarbonate lens and silicone gaskets. RoHS compliant.
Mounting Mounts to standard octagonal box (not included) via universal round mounting bracket. Comes with standard 6 (1829 mm) Cabtire water proof lead (longer leads available).
Approval Wet and dry locations. Approved to US and Canadian standards by CSA.
Notes An appropriate 24V DC LED driver must be used with fixture. Can be used as emergency backup lighting in conjunction with Bodine emergency LED driver (sold separately). Consult factory.
67 See page 192 for explanation of symbols and Ip ratings.
W27S = 2700K, std CRIW30S = 3000K, std CRIW35S = 3500K, std CRIW41S = 4100K, std CRI W20H = 2000K, high CRIW30H = 3000K, high CRI
*only available in W30S & W20H.
NOTE: Standard CrI has a value of 75~82 while high CrI has 92.
W20H has consistent binning that falls within 1.5 MacAdam ellipse.
S = spot (12)N = narrow flood (30)F = flood (60)
Lumen test results provided by Led chip manufacturer.
Image shows L99-1W30SNW30SN-6MA
3-1/4
5-3/8
4-3/81/8
1-5/8 5-3/4
6
3mm
152mm
111mm
41mm 146mm
83mm
137mm
approx. 1300 cdmax.
-0
-90
0
180
90
45-45
-90
0.1 fc120
0.2
Mount height: 9 ft Total LLF: 1
0
1
2
1 1 20
Isofootcandle PlotPolar Candela DistributionL9912 x 1W, 303000K Std1020 lm
approx. 2400 cdmax.
-0
-90
0
180
90
45-45
-90
0.1 fc120
0.2
Mount height: 9 ft Total LLF: 1
0
1
2
1 1 20
Isofootcandle PlotPolar Candela DistributionL9912 x 2.5W, 303000K Std1944 lm
65
64
Wall, Floor &
Ceiling Fixtureswww.mplighting.com
L99
6 = 6 (1829mm) X = custom
L99 2 x 6W/15W LED Wall Sconce
Application Outdoor / indoor wall mounted for up or down illumination.
Source 12 x 1W, 350mA or 12 x 2.5W, 700mA LEDs
Driver Remote 120V primary, 700mA driver (not included).
LED Input Voltage 24V DC
Power Consumption 17W / 35W
Dimming Dimmable with 100W 24V LED driver and controller, 0~10V dimming (not included). See page 186-190 for Recommended Driver Chart.
Weight 5.64lbs (2.56kg).
Material Anodized aluminum or 316 stainless steel. 1/4 (6mm) thick polycarbonate lens and silicone gaskets. RoHS compliant.
Mounting Mounts to standard octagonal box (not included) via universal round mounting bracket. Comes with standard 6 (1829 mm) Cabtire water proof lead (longer leads available).
Approval Wet and dry locations. Approved to US and Canadian standards by CSA.
Notes An appropriate 24V DC LED driver must be used with fixture. Can be used as emergency backup lighting in conjunction with Bodine emergency LED driver (sold separately). Consult factory.
67 See page 192 for explanation of symbols and Ip ratings.
Code WAttAge CoLor up BeAM up CoLor doWN BeAM doWN LeAd LeNgtH FINISH
L99 - -
1 = 6 x 1W2 = 6 x 2.5W*
MA = matte clear anodizedBA = black anodizedS6 = stainless steel 316
W27S = 2700K, std CRIW30S = 3000K, std CRIW35S = 3500K, std CRIW41S = 4100K, std CRI W20H = 2000K, high CRIW30H = 3000K, high CRI
W27S = 2700K, std CRIW30S = 3000K, std CRIW35S = 3500K, std CRIW41S = 4100K, std CRI W20H = 2000K, high CRIW30H = 3000K, high CRI
*only available in W30S & W20H.
NOTE: Standard CrI has a value of 75~82 while high CrI has 92.
W20H has consistent binning that falls within 1.5 MacAdam ellipse.
S = spot (12)N = narrow flood (30)F = flood (60)
S = spot (12)N = narrow flood (30)F = flood (60)
Lumen test results provided by Led chip manufacturer.
Image shows L130-7W30S30-MA
4-3/43/4121mm19mm
Effective Floor Cavity Reflectance: 20%
80 70 50 30 10 0
123456789
10
70 50 30 0 70 50 30 0 50 30 20 50 30 20 50 30 20 0
RCC %:
RW %:RCR: 0 1.12 1.12 1.12 1.12
1.08 1.05 1.03 1.021.03 1.00 .96 .94.99 .94 .91 .87.96 .90 .86 .82.92 .86 .81 .78.89 .82 .78 .74.86 .79 .74 .71.83 .76 .71 .68.80 .73 .68 .65.77 .70 .66 .63
1.09 1.09 1.09 .941.05 1.03 1.02 .901.01 .98 .95 .86.98 .93 .90 .82.94 .89 .85 .79.91 .85 .81 .75.88 .81 .77 .72.85 .78 .74 .70.82 .75 .71 .67.79 .72 .68 .64.77 .70 .66 .62
1.05 1.05 1.051.00 .98 .97.95 .93 .91.91 .88 .85.87 .84 .81.83 .80 .77.80 .76 .74.77 .73 .70.74 .70 .68.72 .68 .65.69 .65 .63
1.00 1.00 1.00.96 .95 .94.92 .90 .89.89 .86 .84.85 .82 .80.82 .79 .76.79 .76 .73.76 .73 .70.73 .70 .67.71 .67 .65.68 .65 .62
.93 .96 .91
.96 .96 .96
.90 .88 .87
.87 .85 .83
.84 .81 .79
.81 .78 .76
.78 .75 .73
.75 .72 .70
.72 .69 .67
.70 .67 .65
.68 .65 .62
.94
.90
.85
.82
.78
.75
.71
.69
.66
.64
.61
approx. 1400 cdmax.
0
180
90
45-45
-90
0 Spread: 31.3 90 Spread: 31.3
18.0
15.0
12.0
9.0
6.0
3.0
10.1
8.4
6.7
5.0
3.4
1.7
10.1
8.4
6.7
5.0
3.4
1.7148.95
37.24
16.55
9.31
5.96
4.14
Center Beam FC Beam Width
Polar Candela DistributionL130303000K Std486 lm
Illuminance at a Distance
Coefficients Of Utilization
Effective Floor Cavity Reflectance: 20%
80 70 50 30 10 0
123456789
10
70 50 30 0 70 50 30 0 50 30 20 50 30 20 50 30 20 0
.93 .91 .90
.98 .98 .98
.87 .84 .82
.81 .78 .76
.77 .73 .70
.72 .68 .65
.68 .64 .60
.64 .60 .56
.60 .56 .53
.57 .53 .49
.54 .49 .46
.89 .88 .87
.94 .94 .94
.84 .82 .80
.79 .77 .74
.75 .72 .69
.71 .67 .64
.67 .63 .60
.63 .59 .56
.59 .55 .52
.56 .52 .49
.53 .49 .46
RCC %:
RW %:RCR: 01.10 1.10 1.10 1.10
1.05 1.02 .99 .97.99 .94 .90 .87.94 .88 .83 .79.89 .82 .76 .72.84 .76 .71 .66.80 .71 .66 .61.76 .67 .61 .57.72 .63 .57 .53.68 .59 .54 .50.65 .56 .50 .47
1.08 1.08 1.08 .931.02 1.00 .98 .86.97 .93 .89 .80.92 .86 .82 .74.87 .80 .75 .69.83 .75 .70 .64.78 .71 .65 .60.75 .66 .61 .56.71 .62 .57 .52.67 .59 .53 .49.64 .55 .50 .46
1.03 1.03 1.03.96 .94 .93.90 .87 .84.84 .80 .77.78 .74 .71.74 .69 .65.69 .64 .61.65 .60 .57.61 .56 .53.58 .53 .49.55 .50 .46
.93
.85
.79
.73
.68
.63
.59
.55
.51
.48
.45
approx. 450 cdmax.
0
180
90
45-45
-90
0 Spread: 60.7 90 Spread: 48.2
18.0
15.0
12.0
9.0
6.0
3.0
21.1
17.5
14.0
10.5
7.0
3.5
16.1
13.4
10.7
8.1
5.4
2.734.95
8.74
3.88
2.18
1.40
0.97
Center Beam FC Beam Width
Polar Candela DistributionL130603000K Std486 lm
Illuminance at a Distance
Coefficients Of Utilization
67
66
Wall, Floor &
Ceiling Fixtureswww.mplighting.com
L130
Code WAttAge CoLor BeAM FINISH
L130 - 7 -
7 = 3 x 2.5W 30 = 30 beam60 = 60 beam
MA = matte clear anodizedBA = black anodized
L130 7.5W Downlight
Application Indoor surface mount downlight.
Source 3 x 2.5W, 700mA LEDs
Driver Integral 120V primary, 9W 700mA non-dimmable driver.
Power Consumption 9W
Dimming 0~10V dimming with remote dimmable driver (not included). See page 186-190 for Recommended Driver Chart.
Weight 0.88lbs (0.39kg).
Material Anodized aluminum. RoHS compliant.
Mounting Mounts to standard octagonal box (not included).
Approval Dry locations. Approved to US and Canadian standards by CSA.
Note Can be used as emergency backup lighting in conjunction with Bodine emergency LED driver (sold separately). Consult factory.
40 See page 192 for explanation of symbols and Ip ratings.
W30S = 3000K, std CRIW20H = 2000K, high CRI
NOTE: Standard CrI has a value of 75~82 while high CrI has 92.
W20H has consistent binning that falls within 1.5 MacAdam ellipse.
Lumen test results provided by Led chip manufacturer.
Image shows L131-7W30S30-MA
4-3/43/4121mm19mm
Effective Floor Cavity Reflectance: 20%
80 70 50 30 10 0
123456789
10
70 50 30 0 70 50 30 0 50 30 20 50 30 20 50 30 20 0
RCC %:
RW %:RCR: 0 1.12 1.12 1.12 1.12
1.08 1.05 1.03 1.021.03 1.00 .96 .94.99 .94 .91 .87.96 .90 .86 .82.92 .86 .81 .78.89 .82 .78 .74.86 .79 .74 .71.83 .76 .71 .68.80 .73 .68 .65.77 .70 .66 .63
1.09 1.09 1.09 .941.05 1.03 1.02 .901.01 .98 .95 .86.98 .93 .90 .82.94 .89 .85 .79.91 .85 .81 .75.88 .81 .77 .72.85 .78 .74 .70.82 .75 .71 .67.79 .72 .68 .64.77 .70 .66 .62
1.05 1.05 1.051.00 .98 .97.95 .93 .91.91 .88 .85.87 .84 .81.83 .80 .77.80 .76 .74.77 .73 .70.74 .70 .68.72 .68 .65.69 .65 .63
1.00 1.00 1.00.96 .95 .94.92 .90 .89.89 .86 .84.85 .82 .80.82 .79 .76.79 .76 .73.76 .73 .70.73 .70 .67.71 .67 .65.68 .65 .62
.93 .96 .91
.96 .96 .96
.90 .88 .87
.87 .85 .83
.84 .81 .79
.81 .78 .76
.78 .75 .73
.75 .72 .70
.72 .69 .67
.70 .67 .65
.68 .65 .62
.94
.90
.85
.82
.78
.75
.71
.69
.66
.64
.61
approx. 1400 cdmax.
0
180
90
45-45
-90
0 Spread: 31.3 90 Spread: 31.3
18.0
15.0
12.0
9.0
6.0
3.0
10.1
8.4
6.7
5.0
3.4
1.7
10.1
8.4
6.7
5.0
3.4
1.7148.95
37.24
16.55
9.31
5.96
4.14
Center Beam FC Beam Width
Polar Candela DistributionL131303000K Std486 lm
Illuminance at a Distance
Coefficients Of Utilization
Effective Floor Cavity Reflectance: 20%
80 70 50 30 10 0
123456789
10
70 50 30 0 70 50 30 0 50 30 20 50 30 20 50 30 20 0
.93 .91 .90
.98 .98 .98
.87 .84 .82
.81 .78 .76
.77 .73 .70
.72 .68 .65