Legacy-GW Features

Rev1.4 24 Jan., 2013

2

Over view

3

Over view

1.Use NCP/TDE （ TDA ） as a legacy GW by stacking connection

with NS1000.

2.NCP/TDE(TDA) connect with NS by stacking card working

as part of One-look network.

4

Over view

Introduce new card ; STACK-M (for NS), STACK-S (1 for NCP/ 1 for TDE)

NS1000 as stacking Master Unit

NCP500NCP1000

STACK-S card

STACK-M cardSite #1

Site #2

Site #3

Site #4　：　：

LAN

Stacking Slave

Stacking Slave

Slave Units

Stacking Slave

Stacking Slave

Proprietary cable for stacking connectionThe length of the cable ： 2M(Dedicate cable for these Stacking card)

Master forOne-look

5

Symbol Model Name Description Remark

STACK-M KX-NS0130 Stacking Master Card

- Interface card for Legacy-GW

- Proprietary Interface x 2 ports

Over view

Symbol Model Name Description Remark

STACK-S (NCP) KX-NS0131

Stacking EXP Card for NCP

Legacy-GW Control Unit for NCP

with Stacking Cable

STACK-S(TDE/TDA) KX-NS0132

Stacking EXP Card for TDE/TDA

Legacy-GW Control Unit for TDE/TDA

with Stacking Cable

New card

6

Condition

7

Condition 1

STACK-S card

STACK-M card

Stacking Slave #1

Stacking Slave #2

1.MPR of NCP has to be removed to install Stack-S card. This means Virtual card on NCP is not supported. All of IP terminal has to connect to NS1000.

2.Type of GW has to be same for each NS1000.

　 Category1: NCP500 /NCP1000

　 Category2: TDE100/200, TDA100/200

Category3: TDE600/620, TDA600/620

3.Max 2 GW for each NS. Max 8 for entire One-look network. 4.TDA15/30/50/100D is not supported.

5. AK is not required to use Legacy GW.

*If the type of cabinet is mixed then

2nd one will not be worked.

8

Condition 2

TDE600

TDE620

NS1000

In case of TDE600 each cabinet count as 1 GW and connection to NS has to be done by Stack-S card.

Bus card in TDE600 and TDE620 has to be removed.

TDE620

TDE620

NS1000

TDE600

TDE600

NS1000

OR OR

9

Symbol Model Description

RMT TDA0196 Analogue Modem for Remote Maintenance

MEC TDA0105/TDE0105

Memory Expansion Card

DSP4 NCP1104 VoIP channel card 4ch

DSP16 TDE0110 VoIP channel card 16ch

DSP64 TDE0111 VoIP channel card 64ch

CTI-LINK TDA0410 CTI Link Card

IP-EXT16 TDA0470 16-Channnel VoIP Extension Card

IP-GW4E TDA0484 4-Channnel VoIP Gateway Card

IP-GW16 TDA0490 16-Channnel VoIP Gateway Card

IP GW4 TDA0480 4 Channel VoIP Gateway Card

MSG4 TDA0191 4-Channel Message Card

ESVM2 TDA0192 2-Channel Simplified Voice Message Card

ESVM4 TDA0194 4-Channel Simplified Voice Message Card

CLCOT8 TDA1180 8-Port Analogue Trunk Base Card w/ Caller ID

CLCOT8E TDA1186 8-Port Analogue Trunk Daughter Card w/ Caller ID

MCSLC24 TDA1178 24-Port Single Line Telephone Card

MCSLC16 TDA1176 16-Port Single Line Telephone Card

Which Optional card can not be used at Legacy GW?

Condition 3

Basically

Optional card

1)on TDE/NCP MPR

2)Support by V5 or later

3) IP-GW, IP-EXT

4) MSG

are not supported.

10

Condition 4

How many CO can be installed in each Legacy GW?Stand-alone Stacking system

One LookNetworking

1NCP5001NCP1000

1TDE/TDA1001TDE/TDA 2001TDE/TDA 600

2NCP5002NCP1000

2TDE/TDA 1002TDE/TDA 2002TDE/TDA 600

Trunk(ch) 256 256 600IP 256 256 256

SIP 256 256 256H.323 48 48 96

Legacy 30 0 64/64/120/128/160 128/128/240/256/256 600

LCOT 2 0 12/16/96/128/160 24/32/192/256/256 600

BRI 8 0 12/16/96/128/160 24/32/192/256/256 600

PRI23 23 0 46/46/92/92/115 92/92/184/184/230 600

PRI30 30 0 60/60/120/120/150 120/120/240/240/256 600

T1 0 0 48/48/96/96/120 96/96/192/192/240 600

E1 0 0 60/60/120/120/150 120/120/240/240/256 600

11

Condition 5

How many EXT can be installed in each Legacy GW?Stand-alone

Stacking systemOne LookNetworkin

g

1NCP1TDE/TDA1001TDE/TDA 2001TDE/TDA 600

2NCP2TDE/TDA 1002TDE/TDA 2002TDE/TDA 600

Extension(ch) 640 640 1000IP 640 640 1000

IP-PT 256 256 1000SIP 640 640 1000

SIP Phone 640 640 1000KX-UT series 640 640 1000

S-PS(SIP based DECT) 255 255 255

Legacy *1 2 0 44/160/256/304 88/320/512/608 1000

SLT 2 0 36/96/128/240 72/192/256/480 1000

DPT 0 0 40/128/256/256 80/256/512/512 1000

12

Stand-aloneStacking system

One LookNetworking

1NCP1TDE/TDA1001TDE/TDA 2001TDE/TDA 600

2NCP2TDE/TDA 1002TDE/TDA 2002TDE/TDA 600

CS (pcs) 64 64 128

DPT-CS (2ch) 0 0 11/32/32/32 22/64/64/64 128

DPT-CS (8ch) 0 0 5/16/16/16 10/32/32/32 64

IP-CS 64 *2 64 *2 128 *2

SIP-CS 64 *3 64 *3 128 *3

PS(DECT)(pcs) 512 512 512

VM

Built-in UM (ch) 24 24 24ch x16

TVA/TVM (ch) 0 0 48 (24ch x2) 24ch x8

Condition 6

*2 The maximum number of Air Sync Groups is 16. An Air Sync Group can contain up to 16 IP-CSs.

*3 The maximum number of Air Sync Groups is 8. An Air Sync Group can contain up to 32 SIP-CSs.

How many other devices can be installed in each Legacy GW?

13

• AK on NCP/TDE can’t be transferred to NS MPR.

Condition 7

• In case of TDA100/200 and TDE100/200

OPB3 card with ECHO16 must be installed in only SLOT1.- Other than OPB3 card allows to install in any SLOT.- OPB3 card with sub-card except for ECHO16 allows installing in any SLOT.

• HGT100, NT400 can’t be connected to NS MPR.

14

How to work?

15

How to work?

Installation

• Both Stack-M and Stack-S card is non hot swappable.• Each cabinet can be power on without any order.• Initial Legacy-GW installation, all card will be initialized.• The optional service cards is hot swappable.

• TVM can be installed as VM system for entire One-look.• CS can be installed at both NS(NCP0158) and Legacy-GW (TDA0141/142/155/156/158). PS can Hand over between these CS to CS(NCP0158, TDA0141/142/155/156/158).

16

How to work?

Wireless•Hand over between NS to Legacy GW and Legacy GW to Legacy GW is available.

CS CS(TDA0141/142/155/156/158)

CS CS

IP-CS IP-CS(NCP0158)LAN

PS

•If Legacy CS and IPCS are mixed then all CS must be assign under Air sync group 1.

17

How to work?

Start up

LED Status

“Stack-M” LED Green On : Normal working condition Off: Error( Not Working)

“Stack-S” LED Green On : INS Red On : Fault Red Flash: OUS

Legacy GW“RUN” LED Green Off :Power off On : Running as GW Slow Flash: While start up

“ALARM” LED Red Off : No present error On : Present Error

18

How to work?

Maintenance

All below service for Legacy-GW is supported through NS1000 cabinet.

• Programming• Firmware update• Error log, Syslog• SNMP information• SMDR

19

Programming

20

Programming at NS1000

Programming

Button to switch Physical-Virtual-LegacyGW1-LegacyGW2

Each Optional Card can be selected and installed.

Stack S connect to “1” on

Stack M consider as “GW1”

21

Programming at NS1000

Programming

LPR Software name same as existing models

LPR Software for STACK-S card “PSTKS” is new!

LPR Software :Software can be download through NS1000

22

Programming at NS1000

Programming

Programming items related to Legacy GW support.

Related to VM. Related to DSS.

Port Property

23

Appendix

24

Appendix

Supported optional card

25

Appendix

Supported optional card

26

Appendix

Supported optional card

27

END

28

20120827-01 LegacyGW_Rev1_27Aug2012Mar.ppt

- 1st release

20120905-02 LegacyGW_Rev1_1_5Sep2012Mar.ppt

- Edit slide #11 revise number of legacy EXT and DPT.

- Add slide #12

20121031-03 LegacyGW_Rev1_2_31Oct2012Mar.ppt

- Add comment for slide #7 “No AK required”

- Add additional sample for slide #8

- Add comment for slide #9 “Basic idea”

- Add comment for #13 about HGT100 and NT400

- Add remark for #16

20121108-04 LegacyGW_Rev1_3_8Nov2012Mar.ppt

- correct slide #8 600-620 twice to 600-620 and 620-620

20130124-05 LegacyGW_Rev1_4_24Jan2013Mar.ppt

- correct slide #10 BRI and LCOT capacity for NCP500 as Legacy GW

Modification