Lesson Plan
Name of the Faculty: Labh Singh
Discipline: Electrical Engg.
Semester: 4th
Subject: Control System
Lesson Plan Duration: 15 Week (January, 2018 to April, 2018)
Work Load (Lecture/Practical) per week (in hours): Lectures-03, Practical-02
Week
Theory Practical
Lecture Day
Topic (including assignment /test )
Practical Day
Topic
1st week
1st
System / Plant model, types of models, illustrative examples of plants & their inputs and outputs, controller
1
To study A.C. servo motor and to
plot its torque-speed
characteristics.
2nd Servomechanism, regulating system
3rd Linear time-invariant (LTI) system
2nd week
1st Time-varying system, causal system
2 To study D.C. servo motor and to plot its torque speed characteristics
2nd open loop & closed loop control system & their illustrative examples
3rd Continuous time and sampled data control systems
3rd week
1st Effects of feedback on sensitivity (to parameter variations)
3
To study the magnetic amplifier
and to plot its load current v/s
control current characteristics for:
(a) series connected mode
2nd Stability, external disturbance (noise)
3rd overall gain, etc. Introductory remarks about non-linear control systems
Week
Theory Practical
Lecture Day
Topic (including assignment /test )
Practical Day
Topic
4th week
1st Concept of transfer function, relationship between transfer function and impulse response
4
To study the magnetic amplifier
and to plot its load current v/s
control current characteristics
for:
(b) parallel connected mode
2nd Order of a system, block diagram algebra
3rd Order of a system, block diagram algebra
5th week
1st Signal flow graphs: Mason’s gain formula & its application
5
To plot the load current v/s
control current characteristics
for self exited mode of the
magnetic amplifier.
2nd Signal flow graphs: Mason’s gain formula & its application
3rd
characteristic equation, derivation of transfer functions of electrical and electromechanical systems
6th week
1st Transfer functions of cascaded and non-loading cascaded elements
6
To study the synchro & to:
(a) Use the synchro pair
(synchro transmitter & control
transformer) as an error
detector.
2nd Typical test signals, time response of first order systems to various standard inputs
3rd
Time response of 2nd order system to step input, relationship between location of roots of characteristics equation.
Week
Theory Practical
Lecture Day
Topic (including assignment /test )
Practical Day
Topic
7th week
1st
ω and ωn, time domain specifications of a general and an under-damped 2nd order system
7
To study the synchro & to:
(b) Plot stator voltage v/s rotor
angle for synchro transmitter i.e.
to use the synchro transmitter as
position transducer.
2nd steady state error and error constants
3rd Dominant closed loop poles
8th week
1st Concept of stability
8
To use the synchro pair (synchro
transmitter & synchro motor) as
a torque transmitter.
2nd Pole-zero configuration and stability
3rd Necessary and sufficient conditions for stability
9th week
1st Hurwitz stability criterion
9
(a) To demonstrate simple
motor-driven closed-loop
position control system.
.
2nd Routh stability criterion and relative stability
3rd Root locus concept
Week
Theory Practical
Lecture Day
Topic (including assignment /test )
Practical Day
Topic
10th week
1st Development of root loci for various systems
10 (b) To study and demonstrate simple closed-loop speed control system
2nd Stability
3rd Considerations
11th week
1st Relationship between frequency response and time-response for 2nd order system
11
To study the lead, lag, lead-lag
compensators and to draw their
magnitude and phase plots.
2nd Polar, Nyquist Plot
3rd Bode plots, stability
12th week
1st Gain-margin and Phase Margin
12
To study a stepper motor & to
execute microprocessor or
computer-based control of the
same by changing number of
steps, direction of rotation &
speed.
2nd Gain-margin and Phase Margin
3rd Relative stability, frequency response specifications
Week
Theory Practical
Lecture Day Topic (including
assignment /test ) Practical
Day Topic
13th week
1st Necessity of compensation, compensation networks
13
To implement a PID controller for
level control of a pilot plant.
2nd
Application of lag and lead compensation
3rd Basic modes of feedback control
14th week
1st Proportional ,integral controllers
14
To implement a PID controller for
temperature control of a pilot
plant.
2nd Derivative controllers
3rd Illustrative examples.
15th
1st Synchros, servomotors
15
To study the MATLAB package
for simulation of control system
design.
2nd Stepper motors
3rd Magnetic amplifier
Lesson Plan
Name of the Faculty: Pawan Siswal
Discipline: Electrical Engg.
Semester: 4th
Subject: Electrical Machine-I
Lesson Plan Duration: 15 Week (January, 2018 to April, 2018)
Work Load (Lecture/Practical) per week (in hours): Lectures-03, Practical-02
Week
Theory Practical
Lecture Day
Topic (including assignment /test )
Practical Day
Topic
1st week
1st Single Phase Transformer: Principle
1
To find turns ratio & polarity of a
1-phase transformer.
2nd construction
3rd E.M.F equation
2nd week
1st Operation of transformer
2 To perform open & short circuit
tests on a 1-phase transformer.
2nd Phasor diagram, Equivalent parameter determination
3rd Equivalent circuit, voltage regulation
3rd week
1st Losses, separation of iron losses
3
To perform Sumpner's back to
back test on 1-phase
transformers.
2nd Efficiency, All day efficiency
3rd Open-circuit test, short circuit test
Week
Theory Practical
Lecture Day
Topic (including assignment /test )
Practical Day
Topic
4th week
1st Sumpner’s test
4
Parallel operation of two 1-
phase transformers.
2nd P.U representation
3rd Parallel operation of 1-Phase transformer
5th week
1st Auto-transformer: Principle, construction
5
To convert three phase to two-
phase By Scott-connection.
2nd
Comparison with two winding transformers
3rd saving of conductor material and its applications
6th week
1st Three Phase Transformer: Principle, construction
6 To perform load test on DC shunt generator.
2nd connection, operation, advantages
3rd various types of connection of three phase transformer
Week
Theory Practical
Lecture Day
Topic (including assignment /test )
Practical Day
Topic
7th week
1st Inrush of magnetizing current
7 Speed control of DC shunt motor.
2nd Harmonic phenomenon
3rd Cooling, rating
8th week
1st Parallel operation
8
Swinburne’s test of DC shunt
motor.
2nd
Three to two phase, three to six phase
3rd Three to twelve phase conversions.
9th week
1st Scott connection
9
Hopkinson’s test of DC shunt
machines.
2nd
Current transformer(C.T) and their applications
3rd Potential transformer (P.T) and their applications
Week
Theory Practical
Lecture Day
Topic (including assignment /test )
Practical Day
Topic
10th week
1st D.C Generator: Principal, Construction
10
Ward Leonard method of speed
control of D.C. motor.
2nd E.M.F equation
3rd Types & characteristics
11th week
1st voltage buildup phenomenon in self excited generator
11
2nd simplex lap and wave windings
3rd Applications
12th week
1st Armature reaction
12
2nd Commutation, method of improving commutation
3rd Parallel operation
Week
Theory Practical
Lecture Day
Topic (including assignment /test )
Practical Day
Topic
13th week
1st D.C Motor: Principle, construction
13
2nd Torque equation
3rd Types & characteristics
14th week
1st starting and starters
14
2nd Speed control
3rd Speed control
15th week
1st Losses, efficiency
15 2nd swinburne’s test, hopkinson’s test
3rd Braking
Lesson Plan
Name of the Faculty: Pawan
Discipline: Electrical Engg
Semester: 4th
Subject: Network Analysis-II
Lesson Plan Duration: 15 Week (January, 2018 to April, 2018)
Work Load (Lecture/Practical) per week (in hours): Lectures-03, Practical-02
Week
Theory Practical
Lecture Day
Topic (including assignment /test )
Practical Day
Topic
1st week
1st Characteristics and Parameters
of two port networks
1 Transient response of RC circuit 2nd Network Configurations
3rd Short circuit Admittance
parameters
2nd week
1st Open-circuit impedance
parameters
2 Transient response of RL circuit.
2nd
Transmission parameters,
hybrid parameters
3rd Condition for reciprocity & symmetry of two-port networks in different parameters
3rd week
1st Condition for reciprocity & symmetry of two-port networks in different parameters
3
.
Transient Response of RLC
Circuit
2nd Inter-relationships between parameters of two-port network
3rd Inter-relationships between parameters of two-port network
Week
Theory Practical
Lecture Day
Topic (including assignment /test )
Practical Day
Topic
4th week
1st Expression of input & output impedances in terms of two port
parameters
4 To calculate and verify "Z" parameters of a two port
network 2nd
Inter-connection of two port networks
3rd Analysis of typical two-port networks
5th week
1st Image impedances
5 To calculate and verify "Y" parameters of a two port network.
2nd Terminal pairs or Ports
3rd Network functions for one-port
and two-port networks
6th week
1st Concept of poles and zeros in
Network functions
6
.
To determine equivalent parameter of parallel connections
of two port network.
2nd Restrictions on pole and zero
Locations for driving point
functions and transfer functions
3rd Restrictions on pole and zero
Locations for driving point
functions and transfer functions
Week
Theory Practical
Lecture Day
Topic (including assignment /test )
Practical Day
Topic
7th week
1st Time domain behavior from the
pole-zero plot
7
To plot the frequency response of
low pass filter and determine
half-power frequency.
2nd Principles of network topology
3rd Graph matrices
8th week
1st Graph matrices
8 To plot the frequency response of high pass filter and determine the
half-power frequency. 2nd Graph matrices
3rd Network analysis using graph
theory
9th week
1st Network analysis using graph
theory
9
To plot the frequency response of
band-pass filter and determine
the band-width.
2nd Types of filters and their characteristics
3rd Filter fundamentals
Week
Theory Practical
Lecture Day
Topic (including assignment /test )
Practical Day
Topic
10th week
1st Classification of Filter
10 To calculate and verify "ABCD" parameters of a two port
network 2nd
Analysis & design of prototype
high-pass
3rd Prototype low-pass
11th week
1st Prototype band-pass
11
To calculate and verify "h"
parameters of a two port
network.
2nd Prototype band-reject
3rd M-derived low-pass
12th week
1st M-derived high-pass filters
12
To determine equivalent
parameter of series connections of
two port network.
2nd Low-pass filter and high-pass
filter with RC & RL circuits
3rd Low-pass filter and high-pass
filter with RC & RL circuits
Week
Theory Practical
Lecture Day
Topic (including assignment /test )
Practical Day
Topic
13th week
1st Band pass filter with RLC
circuit.
13 To synthesize a network of a given network function and
verify its response 2nd
Hurwitz polynomials, Properties
of Hurwitz polynomials
3rd Positive real functions, procedure
of testing of PRV functions
14th week
1st Concept and procedure of
network synthesis
14 Introduction of P-Spice 2nd Properties of expressions of driving point immitances of LC
networks
3rd Foster’s I & II Form
15th
1st Cauer’s I & II form
15 2nd RC & RL Network synthesis
3rd Foster’s & Cauer’s form of
synthesis of lossy networks.
Lesson Plan
Name of the Faculty: Ankit Aryan
Discipline: Electrical Engg.
Semester: 4th
Subject: EMT
Lesson Plan Duration: 15 Week (January, 2018 to April, 2018)
Work Load (Lecture/Practical) per week (in hours): Lectures-03
Week
Theory
Lecture Day
Topic (including assignment /test )
1st week
1 Coulomb’s Law, Gauss’s Law
2 Potential function, field due to a continuous distribution of charge
3 Equi-potential surfaces, Gauss’s Theorem
2nd week
4 Poison’s equation
5 Laplace’s equation
6 Method of electrical images
3rd week
7 Capacitance, electro-static energy, boundary conditions
8 The electro-static uniqueness theorem, far field of a charge distribution
9 Dirac-Delta representation for a point charge and an infinitesimal dipole
Week
Theory
Lecture Day
Topic (including assignment /test )
4th week
10 Faraday’s law of Induction, Ampere’s Work law in the differential vector form
11 Ampere's law for a current element , Ampere’s Force Law
12 Magnetic field due to volume distribution of current and the Dirac-delta function,
5th week
13 Magnetic vector potential, vector potential (Alternative derivation)
14 Far field of a current distribution, equation of continuity
15 Equation of continuity for time varying fields, inconsistency of Ampere’s law
6th week
16 Maxwell’s field equations and their interpretation, solution for free space
conditions
17 Electromagnetic waves in a homogeneous medium, propagation of uniform plane-
wave
18 Relation between E & H in a uniform plane-wave, wave equations for conducting medium
Week
Theory
Lecture Day
Topic (including assignment /test )
7th week
19 Maxwell’s equations using phasor notation
20 Wave propagation in a conducting medium
21 Conductors, dielectrics
8th week
22 Wave propagation in good conductor and good dielectric
23 Depth of penetration
24 Assignment
9th week
25 Polarization
26 Linear, circular and elliptical
27 Reflection and refraction of plane waves at the surface of a perfect conductor
Week
Theory
Lecture Day Topic (including
assignment /test )
10th week
28 Perfect dielectric (both normal incidence as well as oblique incidence)
29 Brewester's angle and Total Marks internal reflection
30 Brewester's angle and Total Marks internal reflection
11th week
31 Assignment
32 Reflection at the surfaces of a conductive medium
33 TEST
12th week
34 Reflection at the surfaces of a conductive medium
35 Surface impedance.
3rd Transmission-line analogy
Week
Theory
Lecture Day
Topic (including assignment /test )
13th week
1st Poynting theorem
2nd Interpretation of E x H
3rd Power loss in a plane conductor
14th week
1st Transmission line as a distributed circuit
2nd Transmission line equation
3rd Travelling & standing waves
15th week
1st Characteristic impedance
2nd Input impedance of terminated line , Reflection coefficient
3rd VSWR, Smith's chart and its applications.
Lesson Plan
Name of the Faculty: Pawan
Discipline: Electrical Engg
Semester: 4th
Subject: Network Analysis-II
Lesson Plan Duration: 15 Week (January, 2018 to April, 2018)
Work Load (Lecture/Practical) per week (in hours): Lectures-03, Practical-02
Week
Theory Practical
Lecture Day
Topic (including assignment /test )
Practical Day
Topic
1st week
1st Characteristics and Parameters
of two port networks
1 Transient response of RC circuit 2nd Network Configurations
3rd Short circuit Admittance
parameters
2nd week
1st Open-circuit impedance
parameters
2 Transient response of RL circuit.
2nd
Transmission parameters,
hybrid parameters
3rd Condition for reciprocity & symmetry of two-port networks in different parameters
3rd week
1st Condition for reciprocity & symmetry of two-port networks in different parameters
3
.
Transient Response of RLC
Circuit
2nd Inter-relationships between parameters of two-port network
3rd Inter-relationships between parameters of two-port network
Week
Theory Practical
Lecture Day
Topic (including assignment /test )
Practical Day
Topic
4th week
1st Expression of input & output impedances in terms of two port
parameters
4 To calculate and verify "Z" parameters of a two port
network 2nd
Inter-connection of two port networks
3rd Analysis of typical two-port networks
5th week
1st Image impedances
5 To calculate and verify "Y" parameters of a two port network.
2nd Terminal pairs or Ports
3rd Network functions for one-port
and two-port networks
6th week
1st Concept of poles and zeros in
Network functions
6
.
To determine equivalent parameter of parallel connections
of two port network.
2nd Restrictions on pole and zero
Locations for driving point
functions and transfer functions
3rd Restrictions on pole and zero
Locations for driving point
functions and transfer functions
Week
Theory Practical
Lecture Day
Topic (including assignment /test )
Practical Day
Topic
7th week
1st Time domain behavior from the
pole-zero plot
7
To plot the frequency response of
low pass filter and determine
half-power frequency.
2nd Principles of network topology
3rd Graph matrices
8th week
1st Graph matrices
8 To plot the frequency response of high pass filter and determine the
half-power frequency. 2nd Graph matrices
3rd Network analysis using graph
theory
9th week
1st Network analysis using graph
theory
9
To plot the frequency response of
band-pass filter and determine
the band-width.
2nd Types of filters and their characteristics
3rd Filter fundamentals
Week
Theory Practical
Lecture Day
Topic (including assignment /test )
Practical Day
Topic
10th week
1st Classification of Filter
10 To calculate and verify "ABCD" parameters of a two port
network 2nd
Analysis & design of prototype
high-pass
3rd Prototype low-pass
11th week
1st Prototype band-pass
11
To calculate and verify "h"
parameters of a two port
network.
2nd Prototype band-reject
3rd M-derived low-pass
12th week
1st M-derived high-pass filters
12
To determine equivalent
parameter of series connections of
two port network.
2nd Low-pass filter and high-pass
filter with RC & RL circuits
3rd Low-pass filter and high-pass
filter with RC & RL circuits
Week
Theory Practical
Lecture Day
Topic (including assignment /test )
Practical Day
Topic
13th week
1st Band pass filter with RLC
circuit.
13 To synthesize a network of a given network function and
verify its response 2nd
Hurwitz polynomials, Properties
of Hurwitz polynomials
3rd Positive real functions, procedure
of testing of PRV functions
14th week
1st Concept and procedure of
network synthesis
14 Introduction of P-Spice 2nd Properties of expressions of driving point immitances of LC
networks
3rd Foster’s I & II Form
15th
1st Cauer’s I & II form
15 2nd RC & RL Network synthesis
3rd Foster’s & Cauer’s form of
synthesis of lossy networks.
Lesson Plan
Name of the Faculty: Rinki
Discipline: Electrical Engg.
Semester: 6th
Subject: Advanced Microprocessor & Microcontroller
Lesson Plan Duration: 15 Week (January, 2018 to April, 2018)
Work Load (Lecture/Practical) per week (in hours): Lectures-03, Practical-02
Week
Theory Practical
Lecture Day
Topic (including assignment /test )
Practical Day
Topic
1st week
1 Introduction to 8086
microprocessor
1
Write a well-documented
program for copying 12 bytes
from source to destination, on
8086 microprocessor kit.
2 RISC and SISC processors
3 Architecture and pin diagram
of 8086
2nd week
4 Architecture and pin diagram
of 8086
2
Write a program for 8086 for division of a defined double word (stored in a data segment) by another double word and verify.
5 Description of various signals
6 Register organization of 8086
3rd week
7
Description of address
computations & memory
segmentation
3
Write a well-documented program for finding the square root of a given number, on 8086, microprocessor kit.
8 Segment override
9 Instruction pipelining,
Week
Theory Practical
Lecture Day
Topic (including assignment /test )
Practical Day
Topic
4th week
10 Timing diagrams, Addressing modes
4 Write a program using 8086 for finding the square of a given number and verify.
11 Test
12 Instruction set of 8086
5th week
13 nstruction execution timing
5 Write a program for 8086 for finding square of a number using look-up table and verify.
14 Instruction format, Data transfer instructions
15 Arithmetic instructions
6th week
16 Branch instructions
6
Write a program to control the operation of stepper motor using 8086 microprocessor and 8255 chip.
17 Loop instructions, NOP & HLT instructions,
Week
Theory Practical
Lecture Day
Topic (including assignment /test )
Practical Day
Topic
7th week
19 Flag manipulation instructions
7 Write a program using 8086 to add a series of 16-bit numbers. 20
Logical instructions, Shift & Rotate instructions,
21 Directives & operators
8th week
22 Interrupts of 8086
8 To study the architecture of 8051 microcontroller. 23
Assembly language Programs using 8086
24 Assignment
9th week
25 The concept of microcontroller
9 Write a program in 8051 to add and subtract two 8 bit numbers. 26
comparison between Microcontrollers & Microprocessors
27 Architecture and Pin diagram of 8051 microcontroller
Week
Theory Practical
Lecture Day
Topic (including assignment /test )
Practical Day
Topic
10th week
28 Architecture and Pin diagram of 8051 microcontroller
10
Write an ALP to generate square
wave of 10 kHz frequency using
timer of 8051 microcontroller.
29 Memory organization. Special function registers
30 External memory, Reset operation. Instruction Set
11th week
31 Addressing modes
11 To find average of Ten 8-bit numbers 32
Arithmetic, Logical. Data transfer
33 Boolean variable manipulation
12th week
34 Program branching instructions etc
12 Write an ALP to interface LED and switches with 8051 microcontroller.
35 Programs based on various
instructions
36 Programs based on various instructions
Week
Theory Practical
Lecture Day Topic (including
assignment /test ) Practical
Day Topic
13th week
37 Timer operation, Timer Mode
register
13
Write a program to find (i) largest number and (ii) smallest number from an array using 8051 microcontroller.
38 Timer Control register. Timer
modes & overflow flag
39 Starting, Stopping & controlling
the timers
14th week
40 Programs for generating square waves of various frequencies.
14
Write a program to generate square wave of 50 Hz frequency using timer of 8051 microcontroller.
41 Serial port operation, UART
42 Serial port control register, Modes of serial port operation.
15th
43 Serial port baud rate.
15 To control the operation of DC motor using 8051 microcontroller. 44
Initialization & programming of serial port. Interrupts of 8051, SFRs related to interrupts, processing interrupts,
45 program design using interrupts. Interfacing with LED, DC motors, stepper motors
Lesson Plan
Name of the Faculty: Pawan Siswal
Discipline: Electrical Engg.
Semester: 6th
Subject: Conventional And Cad Of Electrical Machines
Lesson Plan Duration: 15 Week (January, 2018 to April, 2018
Work Load (Lecture/Practical) per week (in hours): Lectures-03, Practical-02
Week
Theory Practical
Lecture Day
Topic (including assignment /test )
Practical Day
Topic
1st week
1 General features electrical
machine design
1
Yoke design of a transformer.
2 Limitations of electrical
machine design.
3 Types of enclosures
2nd week
4 Heat dissipation
2 L.V. & H.V. windings design of a transformer 5
Temperature rise heating and cooling cycles
6 Ratings of machine machines
3rd week
7 Cooling media used
3 Calculation of losses & efficiency of a transformer 8
Output equation and output coefficient
9 Output equation and output coefficient
Week
Theory Practical
Lecture Day
Topic (including assignment /test )
Practical Day
Topic
4th week
10 Specific electric and magnetic loading
4 Stator design of an induction motor. 11
Specific electric and magnetic loading
12 Effect of size and ventilation
5th week
13 MMF calculation for air gun and iron parts of electrical machines
5
Rotor design of an induction
motor.
14
MMF calculation for air gun and iron parts of electrical machines
15 Gap contraction coefficient
6th week
16 Real and apparent flux densities
6
Calculation of losses & efficiency
of an induction motor.
17 Estimation of magnet current of transformers and rotating machines
Week
Theory Practical
Lecture Day
Topic (including assignment /test )
Practical Day
Topic
7th week
19 Estimation of magnet current of transformers and rotating machines
7
Stator design of a synchronous
machine.
20
No load current of transformers and induction motors
21 Leakage flux and reactance calculations for transformers and rotating machines
8th week
22 Leakage flux and reactance calculations for transformers and rotating machines
8 Rotor design of a synchronous machine. 23 Design of field magnet
24 Assignment
9th week
25 Design of transformer
9
Calculation of losses & efficiency
of a synchronous machine.
26 Design of transformer
27 D.C. machines
Week
Theory Practical
Lecture Day
Topic (including assignment /test )
Practical Day
Topic
10th week
28 D.C. machines
10
Armature winding & field
winding design of a D.C. motor.
29 induction motor
30 induction motor
11th week
31 synchronous machine and their performance calculations
11
Armature core design of a D.C.
motor.
32
synchronous machine and their performance calculations
33 TEST
12th week
34 Computerization of design Procedures
12
Calculation of losses & efficiency
of a D.C. motor.
35
Computerization of design
Procedures
36 Development of Computer program and performance prediction
Week
Theory Practical
Lecture Day Topic (including
assignment /test ) Practical
Day Topic
13th week
37
Development of Computer
program and performance
prediction
13
38 Optimization techniques
39 Optimization techniques
14th week
40 Optimization techniques
14
41 Optimization techniques
42 Their applications to design Problems.
15th
43 Their applications to design Problems.
15
44 ASSIGNMENT
45 TEST
Lesson Plan
Name of the Faculty: Pintu
Discipline: Electrical Engg.
Semester: 6th
Subject: Communication System & Technology
Lesson Plan Duration: 15 Week (January, 2018 to April, 2018)
Work Load (Lecture/Practical) per week (in hours): Lectures-03, Practical-02
Week
Theory Practical
Lecture Day
Topic (including assignment /test )
Practical Day
Topic
1st week
1 Modulation, Demodulation
1 To study and analyze various waveform of Digital modulation 2
Radio Frequency Spectrum,
Signals & their classification,
Limitations & Advantages of a
Communication System
3 Comparison of Analog & Digital
Communication Systems
2nd week
4 Historical Perspective
2 To study different types of Filters.
5
Modes & Medias of
Communication
6 Sources of Noise, External &
Internal Noise
3rd week
7 Noise Calculations
3 To study Amplitude Shift Keying (ASK) modulation.
8
Noise Figure, Noise Figure
Calculation,
9 Noise Temperature
Week
Theory Practical
Lecture Day
Topic (including assignment /test )
Practical Day
Topic
4th week
10 Noise in Communication Systems, Band Pass Noise Model
4 To study Frequency Shift Keying (FSK) modulation.
11
Cascaded States & its Noise Figure Calculation, Signal in presence of Noise
12 Pre-Emphasis & De-Emphasis, Noise Quieting Effect, Capture Effect,
5th week
13 Noise in Modulation Systems
5 To study Phase Shift Keying (PSK) modulation.
14
Basic definition & derivation for Modulation & Modulation Index
15 Modulation & Demodulation of AM
6th week
16 Suppressed Carrier Modulation
6 To study Time Division Multiplexing (TDM).
17 Quadrature Amplitude Modulation
Week
Theory Practical
Lecture Day
Topic (including assignment /test )
Practical Day
Topic
7th week
19 SSB-SC, DSB-SC, VSB Modulation & Demodulation,
7 To study Frequency Division Multiplexing (FDM).
20
Comparison of various AM Systems, Generation of AM waves.
21 Basic definition & derivation for Modulation & Modulation Index
8th week
22 Generation of FM waves, Comparison between PM & FM
8 To study Binary Phase Shift Keying (BPSK) modulation. 23
Frequency Spectrum of FM, B.W. & required spectra, Types of FM
24 vector representation of FM, Universal Curve, Multiple FM,
9th week
25 Demodulation of FM waves,
Demodulation of PM waves,
9 To study Phase Locked Loop (PLL).
26 Comparison between AM & FM
27 Sampling theory, TDM, FDM
Week
Theory Practical
Lecture Day
Topic (including assignment /test )
Practical Day
Topic
10th week
28 PAM, PWM, PPM
10 To study Pulse amplitude modulation and demodulation.
29
Modulation & Demodulation techniques of above all
30 Elements of Pulse Code Modulation
11th week
31 Noise in PCM Systems, Bandwidth of PCM Systems
11 To study Pulse width Modulation(PWM).
32
Measure of Information, Channel Capacity
33 Channel Capacity of PCM System
12th week
34 Differential Pulse Code Modulation (DPCM).
12 To study Pulse Position Modulation(PPM) 35
Delta Modulation (DM), Digital
Modulation-ASK
36 FSK, PSK, DPSK
Week
Theory Practical
Lecture Day Topic (including
assignment /test ) Practical
Day Topic
13th week
37 Transmit & receive antennas
13
To deliver seminar by each student on advance communication system
38 Link budget, line of sight systems
39 Satellite-link-GT ratio of earth
stations
14th week
40 VSATS & GPSS
14
41 Types of optical fibres - step, index & graded index
42 Multi mode & single mode, attenuation & dispersion in fibres
15th
43 Optical transmitters LEDS & laser Diode
15
44 Optical Receivers-PIN & APDS
45 Optical fiber link
Lesson Plan
Name of the Faculty: Pawan
Discipline: Electrical Engg.
Semester: 6th
Subject: Electrical Power Generation
Lesson Plan Duration: 15 Week (January, 2018 to April, 2018)
Work Load (Lecture/Practical) per week (in hours): Lectures-03
Week
Theory
Lecture Day Topic (including
assignment /test )
1st week
1 Energy sources, their availability
2 Recent trends in Power Generation
3 Interconnected Generation of Power Plants
2nd week
4 Load forecasting
5 Load curves
6 Load duration curve
3rd week
7 Base load and Peak load Power Plants
8 Connected Load,
9 Maximum demand
Week
Theory
Lecture Day Topic (including
assignment /test )
4th week
10 Demand factor
11 Group diversity factor, Load factor
12 Significance of load factor
5th week
13 Plant factor , capacity factor
14 Selection of unit size , No. of Units, Reserves
15 Cost of power generation, Depreciation, tariff
6th week
16 Selection of site
17 capacity calculations
18 Classification, advantages, disadvantages
Week
Theory
Lecture Day
Topic (including assignment /test )
7th week
19 Schematic diagram and working of Thermal Power Stations
20 Schematic diagram and working of Thermal Power Stations
21 Schematic diagram and working of Nuclear Power Plant
8th week
22 Schematic diagram and working of Nuclear Power Plant
23 ASSIGNMENT
24 TEST
9th week
25 Selection of site
26 capacity calculations
27 capacity calculations
Week
Theory
Lecture Day
Topic (including assignment /test )
10th week
28 Classification, advantages, disadvantages
29 Schematic diagram and working of Hydro Electric Plant
30 Schematic diagram and working of Hydro Electric Plant
11th week
31 Schematic diagram and working of Hydro Electric Plant
32 Schematic diagram and working of Diesel Power Stations
33 Schematic diagram and working of Diesel Power Stations
12th week
34 Schematic diagram and working of Diesel Power Stations
35 ASSIGNMENT
3rd TEST
Week
Theory
Lecture Day
Topic (including assignment /test )
13th week
1st Wind
2nd Solar
3rd Solar
14th week
1st Tidal
2nd Ocean
3rd Geothermal sources of Energy
15th
1st fuel cell
2nd Magneto Hydro Dynamic (MHD) system
3rd Magneto Hydro Dynamic (MHD) system
Lesson Plan
Name of the Faculty: Rinki
Discipline: Electrical Engg.
Semester: 6th
Subject: Embedded System & Applications
Lesson Plan Duration: 15 Week (January, 2018 to April, 2018
Work Load (Lecture/Practical) per week (in hours): Lectures-03
Week
Theory
Lecture Day Topic (including
assignment /test )
1st week
1 Different types of microcontrollers: Embedded microcontrollers
2 External memory microcontrollers
3 Processor Architectures: Harvard V/S Princeton
2nd week
4 CISC V/S RISC
5 Microcontrollers memory types
6 Microcontrollers features: clocking, i/o pins
3rd week
7 Interrupts, Timers, Peripherals
8 Introduction to PIC microcontrollers
9 Architecture and pipelining
Week
Theory
Lecture Day
Topic (including assignment /test )
4th week
10 Program memory considerations
11 Assignments
12 Addressing modes
5th week
13 CPU registers
14 Instruction set,
15 Simple operations, Interrupt logic
6th week
16 Timer 2 scalar initialization
17 Int Service Interrupt service routine
18 Loop time subroutine
Week
Theory
Lecture Day
Topic (including assignment /test )
7th week
19 External interrupts and timers
20 Synchronous serial port module
21 Serial pheriphal device
8th week
22 O/p port Expansion
23 I/p port expansion
24 UART.
9th week
25 Development tools/ environments
26 Assembly language programming style
27 Interpreters, High level languages
Week
Theory
Lecture Day
Topic (including assignment /test )
10th week
28 Intel hex format object files, Debugging
29 Arithmetic operations, Bit addressing
30 Loop control, Stack operation, Subroutines
11th week
31 RAM direct addressing
32 State machines, Oscillators
33 Timer Interrupts
12th week
34 Memory mapped I/O.
35 Interfacing an LCD to the 8051
3rd 8051 interfacing to ADC
Week
Theory
Lecture Day Topic (including
assignment /test )
13th week
1st Sensors, Interfacing a Stepper Motor
2nd 8051 interfacing to the keyboard
3rd Interfacing a DAC to the 8051
14th week
1st 8255 Interfacing with 8031/51, 8051/31 interfacing to external memory
2nd 8255 Interfacing with 8031/51, 8051/31 interfacing to external memory
3rd Music box, Mouse wheel turning
15th
1st PWM motor control, Aircraft Demonstration
2nd Ultra sonic distance measuring, Temperature Sensor
3rd Pressure Sensor, Magnetic field Sensor.
Lesson Plan
Name of the Faculty: Labh Singh
Discipline: Electrical Engg.
Semester: 6th
Subject: Power System-II
Lesson Plan Duration: 15 Week (January, 2018 to April, 2018)
Work Load (Lecture/Practical) per week (in hours): Lectures-03, Practical-02
Week
Theory Practical
Lecture Day
Topic (including assignment /test )
Practical Day
Topic
1st week
1 Transients on a transmission
line
1
To draw the operating characteristics of IDMT over current relay.
2 short circuit of synchronous
machine at no load and on full
load
3 Symmetrical component
transformation
2nd week
4 phase shift in star-delta transformation
2
To draw the operating characteristics of IDMT under Voltage relay.
5 sequence impedances
6 Single line to ground fault
3rd week
7 line to line fault
3 To draw the operating characteristics of IDMT over
Voltage relay 8
double line to ground fault,
9 open conductor fault.
Week
Theory Practical
Lecture Day
Topic (including assignment /test )
Practical Day
Topic
4th week
10 Assignment
4
To draw the operating characteristics of Differential current relay.
11 Test
12 Theory of arc initiation and
interruption
5th week
13 Restriking voltage transients
5
To draw the operating characteristics of negative sequence relay.
14 Current chopping
15 Circuit breaker ratings
6th week
16 Duties of switch gear
6 To study 33KV substation 17 Automatic switch
18 Air circuit breaker
Week
Theory Practical
Lecture Day
Topic (including assignment /test )
Practical Day
Topic
7th week
19 Bulk oil
7 Single line diagram of electrical
power flow of campus 20 Minimum oil
21 Air blast
8th week
22 SF6 CB
8 To study and designing of Earthing / Grounding.
23
Vacuum and DC circuit
breakers
24 Testing of Circuit breaker
9th week
25 Essential qualities of relay
9 Study the burden effect on the
performance of CT and
measure ratio error 26 Relay classification
27 Principal types of
electromagnetic relays
Week
Theory Practical
Lecture Day
Topic (including assignment /test )
Practical Day
Topic
10th week
28 Attracted armature
10
Find out the sequence
components of currents in
three 1-Phase transformers and
3-Phase transformer and
compare their results.
29 Induction disc induction cup
types
30 Over- current, instantaneous
over-current
11th week
31
IDMT, directional and
differential relays, distance
relays
11
(i) Study over current relay. (ii) Draw the current-time
characteristic of an over current
relay for TMS=1 & 0.5and
PSM=1.25 & 1.0.
32 Plain impedance, mho, reactance relays
33 Zone of protection, primary and backup protections
12th week
34 Transmission line &
feeder protection
12
(i) Study percentage bias
differential relay. (ii) Plot the characteristics of a
percentage bias differential relay
for 20%, 30% and 40% biasing.
35 Pilot wire and carrier current
protection , Transforme
36
Generator, motor and bus zone
protection.
Week
Theory Practical
Lecture Day
Topic (including assignment /test )
Practical Day
Topic
13th week
37 Classification of static relays
13 To perform gas actuated
Buchholz relay. 38 Amplitude and phase
comparators
39 Block-spike and block-average
comparators
14th week
40 Rectifier type relays..
14 Design and simulation of HV
transmission line .
41
Introduction to digital relay: basic principles.
42 Application of microprocessors and computers - recent Trends.
15th 43 Travelling wave relay, relaying schemes based on microwave
and optical fiber link 15
Study filtration and Treatment
of transformer oil Determine
dielectric strength of
transformer oil
Lesson Plan
Name of the Faculty: Labh Singh
Discipline: Electrical Engg.
Semester: 6th
Subject: Power System-II
Lesson Plan Duration: 15 Week (January, 2018 to April, 2018)
Work Load (Lecture/Practical) per week (in hours): Lectures-03, Practical-02
Week
Theory Practical
Lecture Day
Topic (including assignment /test )
Practical Day
Topic
1st week
1 Transients on a transmission
line
1
To draw the operating characteristics of IDMT over current relay.
2 short circuit of synchronous
machine at no load and on full
load
3 Symmetrical component
transformation
2nd week
4 phase shift in star-delta transformation
2
To draw the operating characteristics of IDMT under Voltage relay.
5 sequence impedances
6 Single line to ground fault
3rd week
7 line to line fault
3 To draw the operating characteristics of IDMT over
Voltage relay 8
double line to ground fault,
9 open conductor fault.
Week
Theory Practical
Lecture Day
Topic (including assignment /test )
Practical Day
Topic
4th week
10 Assignment
4
To draw the operating characteristics of Differential current relay.
11 Test
12 Theory of arc initiation and
interruption
5th week
13 Restriking voltage transients
5
To draw the operating characteristics of negative sequence relay.
14 Current chopping
15 Circuit breaker ratings
6th week
16 Duties of switch gear
6 To study 33KV substation 17 Automatic switch
18 Air circuit breaker
Week
Theory Practical
Lecture Day
Topic (including assignment /test )
Practical Day
Topic
7th week
19 Bulk oil
7 Single line diagram of electrical
power flow of campus 20 Minimum oil
21 Air blast
8th week
22 SF6 CB
8 To study and designing of Earthing / Grounding.
23
Vacuum and DC circuit
breakers
24 Testing of Circuit breaker
9th week
25 Essential qualities of relay
9 Study the burden effect on the
performance of CT and
measure ratio error 26 Relay classification
27 Principal types of
electromagnetic relays
Week
Theory Practical
Lecture Day
Topic (including assignment /test )
Practical Day
Topic
10th week
28 Attracted armature
10
Find out the sequence
components of currents in
three 1-Phase transformers and
3-Phase transformer and
compare their results.
29 Induction disc induction cup
types
30 Over- current, instantaneous
over-current
11th week
31
IDMT, directional and
differential relays, distance
relays
11
(i) Study over current relay. (ii) Draw the current-time
characteristic of an over current
relay for TMS=1 & 0.5and
PSM=1.25 & 1.0.
32 Plain impedance, mho, reactance relays
33 Zone of protection, primary and backup protections
12th week
34 Transmission line &
feeder protection
12
(i) Study percentage bias
differential relay. (ii) Plot the characteristics of a
percentage bias differential relay
for 20%, 30% and 40% biasing.
35 Pilot wire and carrier current
protection , Transforme
36
Generator, motor and bus zone
protection.
Week
Theory Practical
Lecture Day
Topic (including assignment /test )
Practical Day
Topic
13th week
37 Classification of static relays
13 To perform gas actuated
Buchholz relay. 38 Amplitude and phase
comparators
39 Block-spike and block-average
comparators
14th week
40 Rectifier type relays..
14 Design and simulation of HV
transmission line .
41
Introduction to digital relay: basic principles.
42 Application of microprocessors and computers - recent Trends.
15th
43 Travelling wave relay, relaying schemes based on microwave
and optical fiber link
15
Study filtration and Treatment
of transformer oil Determine
dielectric strength of
transformer oil 44 Assignment
45 Test
Lesson Plan
Name of the Faculty: Pawan Siswal
Discipline: Electrical Engg.
Semester: 8th
Subject: Advanced Control System
Lesson Plan Duration: 15 Week (January, 2018 to April, 2018
Work Load (Lecture/Practical) per week (in hours): Lectures-03
Week
Theory
Lecture Day Topic (including
assignment /test )
1st week
1 State variable representation of systems by various methods
2 State variable representation of systems by various methods
3 Solution of state equations-state transition matrix
2nd week
4 Solution of state equations-state transition matrix
5 Transfer function from state variable model
6 Controllability & Observability of state variable model
3rd week
7 Controllability & Observability of state variable model
8 Controllability & Observability of state variable model
9 Observer system
Week
Theory
Lecture Day Topic (including
assignment /test )
4th week
10 Phase portrait of linear second order systems.
11 Method of isoclines
12 phase portrait of second order system with non-linearities
5th week
13 phase portrait of second order system with non-linearities
14 phase portrait of second order system with non-linearities
15 limit cycle,
6th week
16 singular points
17 stability of nonlinear system.
18 stability of nonlinear system.
Week
Theory
Lecture Day
Topic (including assignment /test )
7th week
19 Definition, limitations
20 Use of describing function for stability analysis
21 Describing function of ideal relay
8th week
22 Relay with hysteresis & dead zone
23 Relay with hysteresis & dead zone
24 Saturation/coulomb friction & backlash,
9th week
25 Liapunov’s 2nd method
26 Liapunov’s 2nd method
27 Liapunov’s 2nd method
Week
Theory
Lecture Day
Topic (including assignment /test )
10th week
28 Construction of Liapunov Function
29 Construction of Liapunov Function
30 Construction of Liapunov Function
11th week
31 Variation calculus: fundamental concepts
32 Variation calculus: fundamental concepts
33 Functionals of a single function
12th week
34 Functionals of a single function
35 Fixed end point problems-euler-lagrange equation
36 Fixed end point problems-euler-lagrange equation
Week
Theory
Lecture Day
Topic (including assignment /test )
13th week
37 variable end point problem and the transversality conditions
38 variable end point problem and the transversality conditions
39 variable end point problem and the transversality conditions
14th week
40 Limitations of calculus of variation
41 Limitations of calculus of variation
42 Limitations of calculus of variation
15th week
43 Pontryagin’s minimum principle
44 Pontryagin’s minimum principle
45 Pontryagin’s minimum principle
Lesson Plan
Name of the Faculty: Pawan
Discipline: Electrical Engg.
Semester: 8th
Subject: Advanced Instrumentations
Lesson Plan Duration: 15 Week (January, 2018 to April, 2018
Work Load (Lecture/Practical) per week (in hours): Lectures-03
Week
Theory
Lecture Day
Topic (including assignment /test )
1st week
1 Functional block diagram of generalized Instrumentation system.
2 Functional block diagram of generalized Instrumentation system.
3 Input-output configuration
2nd week
4 Input-output configuration
5 Input-output configuration
6 Specifications under steady and transient state & their performance characteristics.
3rd week
7 Specifications under steady and transient state & their performance characteristics.
8 Specifications under steady and transient state & their performance characteristics.
9 Temperature
Week
Theory
Lecture Day
Topic (including assignment /test )
4th week
10 Temperature
11 Temperature
12 Pressure
5th week
13 Pressure
14 displacement,
15 displacement,
6th week
16 Velocity
17 Velocity
18 Acceleration
Week
Theory
Lecture Day
Topic (including assignment /test )
7th week
19 Acceleration
20 Strain and torque type.
21 Strain and torque type.
8th week
22 Current & voltage sensitive bridges
23 Current & voltage sensitive bridges
24 Blumlein Bridges
9th week
25 Shielding & grounding
26 Shielding & grounding
27 Instrumentation Amplifier & its Characteristics
Week
Theory
Lecture Day
Topic (including assignment /test )
10th week
28 Instrumentation Amplifier & its Characteristics
29 Linearizing circuits
30 Wave form and frequency conversion
11th week
31 Wave form and frequency conversion
32 Acitve filters
33 Acitve filters
12th week
34 A/D & D/A converters
35 A/D & D/A converters
36 Balanced modulators & demodulators
Week
Theory
Lecture Day
Topic (including assignment /test )
13th week
37 Balanced modulators & demodulators
38 Interfacing of 8051 Microcontroller with (a) ADC and DAC
39 Interfacing of 8051 Microcontroller with (a) ADC and DAC
14th week
40 Interfacing of 8051 Microcontroller with Alphanumeric Devices (Sixteen-segment Display
41 Interfacing of 8051 Microcontroller with Alphanumeric Devices (Sixteen-segment Display
42 Interfacing of 8051 Microcontroller with Dot Matrix Displays
15th week
43 Interfacing of 8051 Microcontroller with Dot Matrix Displays
44 Interfacing of 8051 Microcontroller with LCD Display
45 Interfacing of 8051 Microcontroller with LCD Display
Lesson Plan
Name of the Faculty: Labh Singh
Discipline: Electrical Engg
Semester: 8th
Subject: CAPSA
Lesson Plan Duration: 15 Week (January, 2018 to April, 2018)
Work Load (Lecture/Practical) per week (in hours): Lectures-03, Practical-02
Week
Theory Practical
Lecture Day
Topic (including assignment /test )
Practical Day
Topic
1st week
1 Power Flow equations
1
Draw the flow chart and develop the computer program for the formation of the Y Bus of a
generalized network
2 Circle diagram
3 Travelling waves in power
Systems
2nd week
4 Introduction to graph theory
2
Draw the flow chart and develop the computer program for the formation of the Z Bus of a
generalized network
5 Tree graph
6 Tree graph
3rd week
7 Co-tree etc
3 To plot the swing curve and
observe the stability 8 Co-tree etc
9 Bus Admittance Matrix
Week
Theory Practical
Lecture Day
Topic (including assignment /test )
Practical Day
Topic
4th week
10 Formation of Y Bus
4
To perform load flow study
using Gauss-Siedel method.
11 Primitive admittance matrix
12 Bus Incidence matrix
5th week
13 Formulation of Y Bus using
singular transformation
5 Perform short circuit study for
any type of fault 14 Formation of twing admittance
matrix
15 Formation of twing admittance
matrix
6th week
16 Formation of Z loop
6 To observe transmission losses and efficiency with variations in
power for the given example 17 Bus Impedance matrix
18 Algorithm for formulation of Z- Bus
Week
Theory Practical
Lecture Day
Topic (including assignment /test )
Practical Day
Topic
7th week
19 Algorithm for formulation of Z-
Bus
7 Design of distribution system
20 All types of modifications
21 All types of modifications
8th week
22 Load flow equations
8 To study the features of EMTP
23 Approximate Load flow study
24 Gauss-Seidel method for Load
flow Study
9th week
25 Gauss-Seidel method for Load
flow Study
9 To study the MATLAB Power
System block set features 26 Algorithm and flow Chart for
Computer application to Load flow studies
27 Newton-Raphson method for
Load flow studies
Week
Theory Practical
Lecture Day
Topic (including assignment /test )
Practical Day
Topic
10th week
28 Newton-Raphson method for
Load flow studies
10 29 Algorithm and flow chart for
Computer Application.
30 Decoupled Load flow Studies
11th week
31 Decoupled Load flow Studies
11 32 Fast Decoupled Load flow
33 Fast Decoupled Load flow
12th week
34 Comparison between G-S & N-R
methods
12 35 Comparison between G-S & N-R
methods
36 Symmetrical Components
Week
Theory Practical
Lecture Day
Topic (including assignment /test )
Practical Day
Topic
13th week
37 Sequence networks for
synchronous machines
13 38 Transforms and transmission Lines
39 Transforms and transmission
Lines
14th week
40 Single line to ground fault
14 41 Line to Line fault
42 Double line to Ground fault
15th week
43 symmetrical fault
15 44 Consideration of Pre fault
currents
45 Consideration of Pre fault
currents
Lesson Plan
Name of the Faculty: Ankit Aryan
Discipline: Electrical Engg
Semester: 8th
Subject: Electrical Power Quality
Lesson Plan Duration: 15 Week (January, 2018 to April, 2018
Work Load (Lecture/Practical) per week (in hours): Lectures-03
Week
Theory
Lecture Day Topic (including
assignment /test )
1st week
1 Power Quality
2 Concern in Power System
3 Power Quality Issues
2nd week
4 Power Quality Issues
5 Standards of Power Quality
6 Sources of Sags and Interruptions
3rd week
7 Fundamental Principles of Protection
8 Solutions at End User Level
9 Solutions at End User Level
Week
Theory
Lecture Day Topic (including
assignment /test )
4th week
10 Comparison of Different Ride-Through Alternatives
11 Comparison of Different Ride-Through Alternatives
12 Comparison of Different Ride-Through Alternatives
5th week
13 Sources of Transient Overvoltages
14 Principles of Overvoltage Protection
15 Devices for Overvoltage Protection
6th week
16 Devices for Overvoltage Protection
17 Strategies for Utility System Lightning Protection
18 Switching Transient Problems with Loads
Week
Theory
Lecture Day
Topic (including assignment /test )
7th week
19 Harmonics Distortion
20 Power System Quantities under Nonsinusoidal Conditions
21 Harmonic Indices
8th week
22 Harmonics Sources from Commercial and Industrial Loads
23 Harmonics Sources from Commercial and Industrial Loads
24 Effects of Harmonic Distortion on Power System Equipments
9th week
25 Reasons for Grounding
26 Typical Wiring and Grounding Problems
27 Solutions to wiring and Grounding Problems
Week
Theory
Lecture Day
Topic (including assignment /test )
10th week
28 Power Quality Monitoring and its Objective
29 Power Quality Measurement Equipments
30 Power Quality Measurement Equipments
11th week
31 Power Quality Evaluation
32 Power Quality Evaluation
33 Different Power Quality Indices used in Power Quality Evaluation
12th week
34 Different Power Quality Indices used in Power Quality Evaluation
35 Passive Filters
36 Active Filters
Week
Theory
Lecture Day
Topic (including assignment /test )
13th week
37 Hybrid Filters
38 STATCOM
39 DSTATCOM
14th week
40 DVR
41 UPQC
42 Distributed Generation and its Advantages and Disadvantages
15th week
43 Different Distributed Generation Technologies
44 Different Interfacing Electrical Systems
45 Power Quality Issues in Distributed Generation
Lesson Plan
Name of the Faculty: Ankit Aryan
Discipline: Electrical Engg.
Semester: 2nd Sem
Subject: Principal of Electrical Engg.
Lesson Plan Duration: 15 Week (January, 2018 to April, 2018
Work Load (Lecture/Practical) per week (in hours): Lectures-03, Practical-02
Week
Theory Practical
Lecture Day
Topic (including assignment /test )
Practical Day
Topic
1st week
1st Basic concepts of electric circuits,
Energy sources, Ohm’s Law,
1 To verify KCL and KVL 2nd Kirchhoff’s laws, Node land Loop Analysis
3rd The venin’s and Norton’s theorem
2nd week
1st The venin’s and Norton’s theorem
2 To verify Thevenin’s & Norton's
Theorems 2nd Reciprocity and Maximum Power Transfer Theorem
3rd Reciprocity and Maximum Power Transfer Theorem
3rd week
1st Superposition and Milliman’s Theorem
3 To verify maximum power transfer
theorem in D.C. Circuit 2nd Superposition and Milliman’s
Theorem
3rd Star-Delta or delta-star transformation
Week
Theory Practical
Lecture Day Topic (including
assignment /test ) Practical
Day Topic
4th week
1st Star-Delta or delta-star transformation
4 To verify reciprocity theorem 2nd Problems
3rd Problems
5th week
1st
Sinusoidal signal, Phasors, Polar & rectangular, exponential & trigonometric representations.
5 To verify Superposition theorem 2nd
Sinusoidal signal, Phasors, Polar & rectangular, exponential & trigonometric representations.
3rd Resistance, Inductance &
Capacitance components
6th week
1st Phasors relationship f o r circuit
elements
6
To study frequency response of a series R-L-C circuit and determine resonant frequency & Q- factor for
various Values of R, L, C
2nd Instantaneous & peak values,
average value
3rd RMS values, Power
,
Week
Theory Practical
Lecture Day
Topic (including assignment /test )
Practical Day
Topic
7th week
1st Behavior of AC series
7
To study frequency response of a parallel R-L-C circuit and determine resonant frequency & Q -Factor for various values of R, L, C.
2nd Parallel circuits
3rd Series and parallel resonance
8th week
1st Series and parallel resonance
8 To perform direct load test of a transformer and plot efficiency Vs load characteristic
2nd Problems
3rd Problems
9th week
1st Phase and line
9 To perform direct load test of a D.C. shunt generator and plot load
voltage Vs load current curve 2nd voltages and currents,
3rd Balanced star and delta circuits
Week
Theory Practical
Lecture Day
Topic (including assignment /test )
Practical Day
Topic
10th week
1st Power equation
To study various type of meters.
2nd Measurement of power by two
wattmeter method
3rd Measurement of power by two wattmeter method
11th week
1st Moving coil type instruments
Measurement of power by three voltmeters / three ammeters method.
2nd Moving coil type instruments
3rd Moving iron type instruments
12th week
1st Electro dynamo type wattmeter
Measurement of power in a three phase system by two watt meter
method 2nd
Induction type Energy meter
3rd Ampere’s law, Mutual Inductance
Week
Theory Practical
Lecture Day
Topic (including assignment /test )
Practical Day
Topic
13th week
1st Construction of transformer
2nd Working principle
3rd Phasor diagrams of Single-phase
transfor
14th week
1st EMF equation
2nd Equivalent circuit of Single-phase transformer
3rd Testing, efficiency and regulation of single-phase transformer, Auto
transformer
15th
1st
Construction and working principle of dc motor and generator, Characteristics of dc motor and
generator
2nd Construction and working principle of3-phase Induction machines
3rd
Construction and working principle 3-phase synchronous machines, Torque- speed
characteristics