PLASMA MONITORSERVICE MANUAL
CAUTIONBEFORE SERVICING THE CHASSIS,READ THE SAFETY PRECAUTIONS IN THIS MANUAL.
CHASSIS : RF-04GA
MODEL : MZ-42PM12X
website:http://biz.LGservice.come-mail:http://www.LGEservice.com/techsup.html
- 2 -
CONTENTS
CONTENTS .............................................................................................................2
SAFETY PRECAUTIONS .......................................................................................3
ADJUSTMENT INSTRUCTIONS ............................................................................4
SPECIFICATIONS................................................................................................ 13
ADJUSTMENT INSTRUCTIONS ..........................................................................16
TROUBLE SHOOTING GUIDE.............................................................................18
BLOCK DIAGRAM................................................................................................29
EXPLODED VIEW.................................................................................................32
EXPLODED VIEW PARTS LIST ...........................................................................33
REPLACEMENT PARTS LIST..............................................................................34
SCHEMATIC DIAGRAM ...........................................................................................
PRINTED CIRCUIT BOARD .....................................................................................
- 3 -
SAFETY PRECAUTIONS
Many electrical and mechanical parts in this chassis have special safety-related characteristics. These parts are identified by inthe Schematic Diagram and Replacement Parts List. It is essential that these special safety parts should be replaced with the same components as recommended in this manual toprevent X-RADIATION, Shock, Fire, or other Hazards. Do not modify the original design without permission of manufacturer.
General Guidance
An isolation Transformer should always be used duringthe servicing of a receiver whose chassis is not isolated fromthe AC power line. Use a transformer of adequate power ratingas this protects the technician from accidents resulting inpersonal injury from electrical shocks.
It will also protect the receiver and it's components from beingdamaged by accidental shorts of the circuitry that may beinadvertently introduced during the service operation.
If any fuse (or Fusible Resistor) in this monitor is blown, replaceit with the specified.
When replacing a high wattage resistor (Oxide Metal FilmResistor, over 1W), keep the resistor 10mm away from PCB.
Keep wires away from high voltage or high temperature parts.
Due to high vacuum and large surface area of picture tube,extreme care should be used in handling the Picture Tube.Do not lift the Picture tube by it's Neck.
Leakage Current Cold Check(Antenna Cold Check)With the instrument AC plug removed from AC source,connect an electrical jumper across the two AC plug prongs.Place the AC switch in the on position, connect one lead ofohm-meter to the AC plug prongs tied together and touch otherohm-meter lead in turn to each exposed metallic parts such asantenna terminals, phone jacks, etc. If the exposed metallic part has a return path to the chassis, themeasured resistance should be between 1MΩ and 5.2MΩ. When the exposed metal has no return path to the chassis thereading must be infinite.An other abnormality exists that must be corrected before thereceiver is returned to the customer.
Leakage Current Hot Check (See below Figure) Plug the AC cord directly into the AC outlet.Do not use a line Isolation Transformer during this check. Connect 1.5K/10watt resistor in parallel with a 0.15uF capacitorbetween a known good earth ground (Water Pipe, Conduit, etc.)and the exposed metallic parts.Measure the AC voltage across the resistor using ACvoltmeter with 1000 ohms/volt or more sensitivity.Reverse plug the AC cord into the AC outlet and repeat ACvoltage measurements for each exposed metallic part. Anyvoltage measured must not exceed 0.75 volt RMS which iscorresponds to 0.5mA.In case any measurement is out of the limits specified, there ispossibility of shock hazard and the set must be checked andrepaired before it is returned to the customer.
Leakage Current Hot Check circuit
1.5 Kohm/10W
To Instrument'sexposed METALLIC PARTS
Good Earth Groundsuch as WATER PIPE,CONDUIT etc.
AC Volt-meter
IMPORTANT SAFETY NOTICE
0.15uF
Remote Control Key FunctionsRemote Control Key Functions- When using the remote control aim it at the remote control sensor of the set.- There's maybe a defect in consecutive operation of remote control in specified brightness according to this set feature.
POWERMUTE
PIP INPUT MULTIMEDIA
EXIT ARC MENU
VOLOK
1 2 3
4 5 6
7
PSM SSM
8 9
0
VOL
SPLIT ZOOM PIP/DW SLEEP
SCAN-
SKIP-
WIN. SIZE
SCAN+PLAY
POSITION
SKIP+STOP
SWAP
POWERPAUSE
INPUT SELECT
MULTIMEDIASelects the Component, RGB or DVI
modes.
WIN.SIZEAdjusts the sub picture size.
POWERswitches the set on from standby oroff to standby.
ARC Changes the picture format.
MENUDisplays on screen menus one byone.Exits the current menu.Memorizes menu changes.
SSMTo select the sound appropriate toyour viewing programme character.
NUMBER buttons
SLEEPSets the sleep timer.
PIP/DWSwitches the sub picture on or off.Selects PIP or DW modes.
DVD BUTTONScontrols a LG DVD player.
SWAPAlternates between main and sub pic-ture.
INPUT SELECT
EXITClears all on-screen displays.
PIP INPUTSelects the input mode for the sub pic-
ture.
MUTESwitches the sound on or off.
DD / EESelects a menu option.
FF / GG (Volume Up/Down)Increases/decreases sound level.
Adjusts menu settings.OK
accepts your selection or displays thecurrent mode.
PSMAdjusts the factory preset picture
according to the room.
SPLIT ZOOMEnlarge the screen with regular
ration.
POSITIONMoves the sub picture to DD / EE or FF / GG
direction.
DESCRIPTION OF CONTROLS
- 4 -
- 5 -
<Front Panel Controls>
or
ON/OFF
VOLMENUINPUT SELECTON/OFF
- Shown is a simplified representation of the set.- Here shown may be somewhat different from your set.
1. Main Power Button
2. Remote Control Sensor
3. Power Standby IndicatorIlluminates red in standby mode, Illuminates green when theset is turned on
4. INPUT SELECT Button
5. MENUDisplays on screen menus one by one.Exits the current menu.Memorizes menu changes.
6. DD / EESelects a menu option.FF / GG (Volume Up/Down)Increases/decreases sound level.Adjusts menu settings.
1 2 3 4 5 6
1
4
5
6
3 2
- 6 -
<Back Panel>
R LR L
AC INPUTAUDIO INPUT
AUDIO INPUT VIDEO INPUTAUDIO INPUTS-VIDEO
RGB OUTPUTRGB INPUTDVI INPUTRS-232C INPUT(CONTROL/SERVICE)
REMOTECONTROL
Y PB PR
AUDIO (MONO)
COMPONENT INPUT
R L
EXTERNAL SPEAKER
Connection to PC Connection to AV equipment
- 7 -
<Back Panel>
AV1AV1
AC INPUTAUDIO INPUT RGB OUTPUTRGB INPUTDVI INPUTRS-232C INPUT(CONTROL/SERVICE)
REMOTECONTROL
R L
EXTERNAL SPEAKER
R L
AUDIO INPUT S-VIDEO
Y PB PR
COMPONENT INPUT
AV1 AV2
RCA Type
Scart Type
5
R LAC INPUTAUDIO INPUT
VIDEO INPUTAUDIO INPUT
RGB OUTPUTRGB INPUTDVI INPUTRS-232C INPUT(CONTROL/SERVICE)
REMOTECONTROL
AUDIO (MONO)
R L
EXTERNAL SPEAKER
R L
AUDIO INPUT S-VIDEO
Y PB PR
COMPONENT INPUT
1 2 3 645
1. CONTROL LOCK / REMOTE CONTROL
2. RS-232C INPUT(CONTROL/SERVICE) PORTConnect to the RS-232C port on a PC.
3. DVI INPUT / AUDIO INPUT / RGB INPUT SOCKETSConnect the monitor output socket of the PERSONAL COM-PUTER to this socket.
RGB OUTPUT SOCKETYou can watch the RGB signal on another monitor, connectRGB OUTPUT to another monitor’s PC input port.
4. EXTERNAL SPEAKER OUTPUT (8 ohm)Connect to optional external speaker(s).*For further information, refer to ‘Speaker & Speaker Stand’manual.
5. COMPONENT / AUDIO INPUT SOCKETSS-VIDEO / AUDIO (L/MONO) INPUT SOCKETSVIDEO / AUDIO (L/MONO) INPUT SOCKETS
EURO SCART SOCKET
Note: If you want to use your external hi-fi stereo system,turn off the internal speakers of the set.
6. POWER CORD SOCKETThis Monitor operates on an AC power. The voltage is indi-cated on the Specifications page. Never attempt to operatethe Monitor on DC power.
- 8 -
External Equipment VExternal Equipment V iewing Setupsiewing SetupsWatching VCR (When the Interface board is installed.)
- When connecting the Plasma Monitor with external equipments, match the colours of connecting ports (Video - yellow,Audio(L) - white, Audio(R) -red).
- Connect the VIDEO INPUT socket(yellow) with the BNC-RCA adapter to the VIDEO INPUT socket of the set.- If you have a mono VCR, connect the audio cable from the VCR to the AUDIO(L/MONO) input of the Plasma Monitor. - If you connect an S-VIDEO VCR to the S-VIDEO input, the picture quality is improved; compared to connecting a regu-
lar VCR to the Video input. - Or, connect the Euro scart socket of the VCR to the Euro scart socket of the set.
Avoid having a fixed image remain on the screen for a long period of time. Typically a frozen still picture from a VCR,4:3 picture format or if a CH label is present; the fixed image may remain visible on the screen.Use the orbiter function to avoid having a fixed image. (Refer to p.20)
1. Press INPUT SELECT button on the remote control and select AV or (AV1 or AV2).(When connecting with S-Video, select the S-Video.)
2. Insert a video tape into the VCR and press the PLAY button on the VCR. (See VCR owner’s manual)
Watching external AV source (When the Interface board is installed.)
- When connecting the Plasma Monitor with external equipments, match the colours of connecting ports.- Or, connect the Euro scart socket of the VCR to the Euro scart socket of the set.
1. Press INPUT SELECT button on the remote control of the monitor to select AV or (AV1 or AV2).2. Operate the corresponding external equipment. (See external equipment operating guide.)
Watching Cable TV (When the Interface board is installed.)
- After subscribing to a cable TV service from a local provider and installing a converter, you can watch cable TV program-ming. This monitor cannot display TV programming without a TV tuner device or cable TV converter box connected to themonitor.
1. Press INPUT SELECT button on the remote control and select AV or (AV1 or AV2).2. Tune to cable service provided channels using the cable box.
• Component Input portsYou can get better picture quality if you con-nect DVD player with component input portsas below.
Component ports of theMonitor
Y PB PR
Video output ports of DVD player
YYYY
PbB-YCbPB
PrR-YCrPR
Watching DVD (When the Interface board is installed.)
How to connect- Connect DVD video inputs to Y, PB, PR of COMPONENT (DVD
INPUT) and audio inputs to Audio sockets of AUDIO INPUT.- Or, connect the Euro scart socket of the VCR to the Euro scart socket
of the set.
How to use1. Press INPUT SELECT button on the remote control of the monitor to
select Component or (AV1 or AV2).2. Try this after turning on the DVD player.
(Refer to the DVD player's manual for operating instructions.)
- 9 -
Connecting PC- To enjoy vivid picture and sound, connect a PC to the set.- Avoid keeping a fixed image on the set’s screen for a long period of time. The fixed image may become permanently imprinted on
the screen; use a screen saver when possible.- Connect PC to the RGB INPUT(PC INPUT) or DVI INPUT(DIGITAL RGB INPUT) port of the set; change the resolution output of
PC accordingly.- There might be a noise according to some resolution, vertical pattern, contrast or brightness in PC mode. Then change the PC
mode into other resolution or change the refresh rate into other rate or adjust the brightness and contrast on the menu until thepicture is clean. If the refresh rate of the PC graphic card can not be changed, change the PC graphic card or consult it to themanufacturer of the PC graphic card.
- The synchronization input form for Horizontal and Vertical frequencies is separate.
Setup Instructions to Connect a PC to your set- We recommend using 1024x768, 60Hz for the PC mode, they provide the best picture quality.
In MT/MZ-42PM10/11/20/21 series, we recommend using 640x480, 60Hz for the PC mode, they provide the best picture quality.- If the resolution of PC is over UXGA, there will be no picture on the set.- Connect the signal cable from the monitor output port of the PC to the RGB INPUT port of the set or the signal cable from the DVI
output port of the PC to the DVI INPUT port on the set.- Connect the audio cable from the PC to the Audio input on the set. (Audio cables are not included with the set).- If using a sound card, adjust PC sound as required.- This set apply a VESA Plug and Play Solution. The set provides EDID data to the PC system with a DDC protocol. The PC adjusts
automatically to use this set.- DDC protocol is preset for RGB (Analog RGB), DVI (Digital RGB) mode.- If required, adjust the set settings for Plug and Play functionally.- If graphic card on the PC does not output analog and digital RGB simultaneously, connect only one of both RGB INPUT or DVI
INPUT to display the PC on the set.If graphic card on the PC does output analog and digital RGB simultaneously, set the set to either RGB or DVI; (the other modeis set to Plug and Play automatically by the set.)
- DOS mode may not work depending on video card if using a DVI-I cable.
PC Setup1. Turn on the PC and apply power to the set.2. Turn on the display by pressing the POWER button on the set’s remote control.3. Use the INPUT SELECT or MULTIMEDIA button on the remote control to select the RGB or DVI input source.4. Set the resolution output of the PC to SXGA or under (1280 x 1024, 60Hz). (Refer to p. 12)
Watching DTV Setup (option)
- To watch digitally broadcast programs, purchase/connect a digital set-top box.
How to connect a user-supplied Digital Set-T op Box- Connect DTV set-top box video output to monitor COMPONENT
(DVD/DTV INPUT) or to the monitor RGB (PC/DTV INPUT) or to themonitor DVI (PC/DTV INPUT) connector depending on your set-topbox connectors.
- Connect DTV set-top box audio outputs to monitor AUDIO INPUTjacks.
How to use1. Turn on the a digital set-top box. (Refer to the owner’s manual for the
digital set-top box)2. Use INPUT SELECT on the remote control to select Component, RGB or
DVI.
• DTV Input signal
486p (60Hz)
576p (50Hz)
720p
1080i
ModeTerminal Component
o
o
o
o
RGB (DTV)
o
o
o
o
DVI (DTV)
o
o
o
o
- 10 -
Displayable Monitor SpecificationDisplayable Monitor Specification
RGB / DVI mode
MT/MZ-42PM12X seriesMT/MZ-50PM10/11/20/21 series
Resolution
640x350
720x400
640x480
848x480
800x600
HorizontalFrequency(KHz)
VerticalFrequency(Hz)
852x480
832x624
1024x768
1360x768
1366x768
1152x864
1152x870
1280x960
1280x768
1280x1024
70.09
85.08
70.08
85.03
59.94
66.66
72.80
75.00
85.00
60.00
70.00
75.00
60.00
70.00
75.00
56.25 (RGB)
60.31
72.18
75.00
85.06
74.55
60.00
70.06
75.02
85.00
60.00
75.02
85.00
60.00
75.02
85.00
60.05
70.01
75.00
85.00
75.06
60.00
75.00
85.00
60.02
60.02
31.468
37.861
31.469
37.927
31.469
35.000
37.861
37.500
43.269
31.500
37.799
39.375
31.500
37.799
39.375
35.156
37.879
48.077
46.875
53.674
49.725
48.363
56.476
60.023
68.677
47.700
59.625
68.500
47.700
59.625
69.500
54.348
63.995
67.500
77.487
68.681
47.693
60.091
68.504
60.023
63.981
RGB / DVI mode
MT/MZ-42PM10/11/20/21 series
Resolution
640x350
720x400
640x480
848x480
800x600
HorizontalFrequency(KHz)
VerticalFrequency(Hz)
852x480
832x624
1024x768
1360x768
1366x768
1152x864
1152x870
1280x960
1280x768
1280x1024
70.09
85.08
70.08
85.03
59.94
66.66
72.80
75.00
85.00
60.00
70.00
75.00
60.00
70.00
75.00
56.25
60.31
72.18
75.00
85.06
74.55
60.00
70.06
75.02
85.00
60.00
75.02
60.00
75.02
60.05
70.01
75.00
85.00
75.06
60.00
75.00
85.00
60.02
60.02
31.468
37.861
31.469
37.927
31.469
35.000
37.861
37.500
43.269
31.500
37.799
39.375
31.500
37.799
39.375
35.156
37.879
48.077
46.875
53.674
49.725
48.363
56.476
60.023
68.677
47.700
59.625
47.700
59.625
54.348
63.995
67.500
77.487
68.681
47.693
60.091
68.504
60.023
63.981
- 11 -
AS mark
LG TV
Owner’s Manual
1.5V1.5V
Alkaline batteries
Power Cord
POWERMUTE
PIP INPUT MULTIMEDIA
EXIT ARC MENU
VOLOK
1 2 3
4 5 6
7
PSM SSM
8 9
0
VOL
SPLIT ZOOM PIP/DW SLEEP
SCAN-
SKIP-
WIN. SIZE
SCAN+PLAY
POSITION
SKIP+STOP
SWAP
POWERPAUSE
INPUT SELECT
Remote Control handset
- Optional extras can be changed or modified for quality improvement without any notification new optional extras can beadded.
- Contract your dealer for buying these items.
Optional Extras
AccessoriesAccessories
Tilt wall mounting bracket
404250 40 42 50
Ceiling mounting bracket
40
4250
42
40
Desktop stand Speakers
BNC-RCA adapter(optional)
- 12 -
Installation OptionsInstallation Options
Desktop Pedestal Installation
• The set can be mounted on a desk as shown above.(For further information, refer to the optional 'DesktopStand Installation and Setup Guide'.)
• Speakers and speaker stands shown are optional, andare shown for example only.
• The set can be installed in different ways such as on a wall, or on a desktop etc.• Install this set only in a location where adequate ventilation is available.• This set is designed so that it can be mounted either horizontally or vertically.
Wall Mount: Horizontal Installation
• The set can be installed on a wall as shown above. (Forfurther information, refer to the optional ‘Wall MountingBracket Installation and Setup Guide’.)
• Speakers are optional, and are shown for illustration only.
3cm
10cm
10cm
10cm10cm
To Mount on a W allWall mount minimum allowable clearances for ade-quate ventilation.
To Install on a DesktopPedestal mount minimum allowable clearances foradequate ventilation.
Wall Mount: V ertical Installation
• The monitor can be installed vertically on the wall asshown above.(For further information, refer to theoptional ‘Wall Mounting Bracket Installation and SetupGuide’.)Caution: When installing the monitor vertically, thefront panel controls must be in the left-down side posi-tion as shown above.
• Speakers are optional, and are shown for illustrationonly.
• Note: To use the Monitor in a vertical orientation, thesource's image must also be in a vertical format.
- 13 -
SPECIFICATIONSNOTE : Specifications and others are subject to change without notice for improvement.
V Application RangeThis spec is sheet is applide to the 42”,50” PDP TV used RF-04GA chassis.
V Specification
Each part is tested as below without special appointment.1) Temperature : 25¡ 5°C (77¡ 9°F)2) Relative Humidity: 65¡ 10%3) Power Voltage: Standard Input voltage (100V-240V~, 50/60Hz)
* Standard Voltage of each product is marked by models.4) Specification and performance of each parts are followed each drawing and specification by part number in
accordance with BOM.5) The receiver must be operated for about 20 minutes prior to the adjustment.
V Test and Inspection Method1) Performance : LGE TV test method followed.2) Demanded other specification
Safety: CE, IEC specificationEMC : CE, IEC
Remark
Safety : IEC60065
EMI : EN55022
EMS : EN55024
Safety : IEC60065,IE60950
EMI : EN55022
Model Name
MZ-42PM10
MZ-42PM12X
MZ-50PM10
MZ-50PM20
MT-42PM10
MT-42PM20
MT-42PM12X
MT-50PM10
MT-50PM20
Market
EU
Non-EU
Market Place
EU
Non-EU
Chassis
RF-04GA
Model Name
MZ-42PM10
MZ-42PM12X
MZ-50PM10
MZ-50PM20
MT-42PM10
MT-42PM20
MT-42PM12X
MT-50PM10
MT-50PM20
Brand
LG
LG
- 14 -
V General Specification
1. General Specification (42” VGA MODULE)
2. General Specification (42” XGA MODULE)
3. General Specification (50” XGA MODULE)
Remark
PDP
LGE
Maker : NBK / Mitsui / LG Chemical
LGE SPEC
Maker : SONY / Murata / Sanken
Specification
42 inch wide Color Display Module
16:9
PDP42V6000
45% Total light transmittance (E- Mesh)
1) Temp : 0~40 deg
2) Humidity : 0~85%
1) Temp : -20~60 deg
2) Humidity : 0~85%
100-240V~, 50/60Hz
No
1
2
3
4
5
6
7
Item
Display Screen Device
Aspect Ratio
PDP Module
Screen Filter
Operating Environment
Storage Environment
Input Voltage
Remark
PDP
Maker : NBK / Mitsui / LG Chemical
LGE SPEC
Maker : SONY / Sanken
Specification
42 inch wide Color Display Module
16:9
PDP42X1A###, RGB Closed Type
45% Total light transmittance (E- Mesh)
1) Temp : 0~40 deg
2) Humidity : 0~85%
1) Temp : -20~60 deg
2) Humidity : 0~85%
AC100 ~ 240V, 50/60Hz
No
8
9
10
11
12
13
14
Item
Display Screen Device
Aspect Ratio
PDP Module
Screen Filter
Operating Environment
Storage Environment
Input Voltage
Remark
PDP
LGE
Maker : NBK / Mitsui / LG Chemical
LGE SPEC
Maker : SONY / Sanken
Specification
50 inch wide Color Display Module
16:9
PDP50X2###, RGB Closed Type
45% Total light transmittance (E- Mesh)
1) Temp : 0~40 deg
2) Humidity : 0~85%
1) Temp : -20~60 deg
2) Humidity : 0~85%
100-240V~, 50/60Hz
No
15
16
17
18
19
20
21
Item
Display Screen Device
Aspect Ratio
PDP Module
Screen Filter
Operating Environment
Storage Environment
Input Voltage
V Model Specification
1. MZ-42PM10 / 42PM12X / 50PM10 / 50PM20
2. MT-42PM10 / 42PM20 / 42PM12X / 50PM10 / 50PM20
- 15 -
Remark
4 System : PAL, B/G/I/D/K, SECAM L/,
NTSC4.43, PAL60
4 System : PAL, B/G/I/D/K, SECAM L/,
NTSC4.43, PAL60
Up to UXGA@60Hz/480P
Up to UXGA@60Hz/480P
DVI-D
L/R Input
Specification
EU
PAL, SECAM
PAL, SECAM, NTSC
Y/ Cb/ Cr, Y/ Pb/ Pr
RGB-PC/DTV
RGB-PC/DTV
DVI-PC/DTV
PC Audio, Component,S-VHS, CVBS
Discrete IR
No
22
23
24
25
26
27
28
29
30
Item
Market
Scart Jack (2EA )
S-AV Input (1EA )
Component Input (1EA )
RGB Input (1EA )
RGB Outpu t (1EA )
DVI Input (1EA )
Audio Input (4EA )
Wired Control
Remark
4 System : PAL, B/G/I/D/K, SECAM L/,
NTSC4.43, PAL60
4 System : PAL, B/G/I/D/K, SECAM L/,
NTSC4.43, PAL60
Up to UXGA@60Hz/480P
Up to UXGA@60Hz/480P
DVI-D
L/R Input
Specification
Non-EU
PAL, SECAM, NTSC
PAL, SECAM, NTSC
Y/ Cb/ Cr, Y/ Pb/ Pr
RGB-PC/DTV
RGB-PC/DTV
DVI-PC/DTV
PC Audio, Component,S-VHS, CVBS
Discrete IR
No
31
32
33
34
35
36
37
38
39
Item
Market
Scart Jack (2EA )
S-AV Input (1EA )
Component Input (1EA )
RGB Input (1EA )
RGB Outpu t (1EA )
DVI Input (1EA )
Audio Input (4EA )
Wired Control
- 16 -
ADJUSTMENT INSTRUCTIONS
1. Application ObjectThis spec sjeet os applied all of the 42”, 50”, RF-04GAchassis bymanufacturing LG TV Plant or sort plant.
2. Specification(1) Because this is not a hot chassis, it is not necessary to
use an isolation transformer. However, the use of isolationtransformer will help protect test instrument.
(2) Adjustment must be done in the correct order.(3) The adjustment must be performed in the circumstance of
25±5°C of temperature and 65±10% of relative humidity ifthere is no specific designation.
(4) The input voltage of the receiver must keep 100-220V~,50/60Hz.
(5) The receiver must be operated for about 15 minutes priorto the adjustment.
O After RGB Full white HEAT-RUN Mode, the receiver mustbe operated prior to adjustment.
O Enter into HEAT-RUN MODE1) Press the POWER ON KEY on R/C for adjustment.2) OSD display and screen display 100% full WHITE
PATTERN.
[ Set is activated HEAT-RUN without signal generator inthis mode.
[ Single color pattern(RED/BLUE/GREEN) of HEAT-RUN mode uses to check pannel.
Caution) If you turn on a still screen more than 20 minutes(Especially digital pattern, cross hatch pattern), a afterimage may be occur in the black level part of thescreen.
3. POWER PCB Assy V oltage Adjustments (Va, Vs Voltage Adjustments)
3-1. Test Equipment : D.M.M. 1EA
3-2. Connection Diagram for MeasuringRefer to [Fig 1]
3-3. Adjustment Method for
(1) Va Adjustment1) After receiving 100% Full White Pattern, HEAT RUN.2) Connect + terminal of D.M.M to Va pin of P805, connect
- terminal to GND pin of P805.3) After turningVR351, voltage of D.M.M adjustment as
same as Va voltage which on lable of panel right/top(Deviation; ±0.5V)
(2) Vs Adjustment1) Connect + terminal of D.M.M to Vs pin of P805, connect
– terminal to GND pin of P805.2) After turning RV551, voltage of D.M.M adjustment as
same as Va voltage which on label of panel right/top.(Deviation; ±0.5V)
4. Auto RGB Color balance
4-1 Pattern Equipment :PC Pattern Generator( 801F or VG828 )
(16Gray Scale Pattern output(RGB output Level: 0.7Vp-p))
4-2 Method of Auto RGB Color Balance(1) Input RGB Source: 16Gray Scale Pattern output
(RGB output Level: 0.7Vp-p)(2) Press ADJ KEY on R/C for adjustment.(3) Press Vol. +KEY and Operate To Set.(4) Auto-RGB OK means completed adjustment.
P805
P804
P806
P803
P802
P801
VR351
GND
GND
Va
Va
Vs
Vs
Vs Vs ADJVR551
VR5
Vs ADJ
[Fig. 1] Connection Diagram of Power Adjustment for Measuring
[Fig. 2] Auto RGB Color Balance Test Pattern
- 17 -
4-3 Adjustment of White Balance
(1) Required EquipmentColor Analyzer( CA-100 or same product)
(2) Connecting diagram of equipment for measuring.
If you are adjusting a MZ Model, Use the RCA to SCART(Out)cable to input a AV signal.
(3) Adjustment of White BalanceO Operate the zero-calibration of the CA-100, then stick sensor
to PDP module surface when you adjust..O For manual adjustment, It is also possible by the following
sequence.1) Select white pattern of heat-run mode by pressing power
on ket on remote control for adjustment then operate heatrun more than 15 minute.
2) Supply Gray Pattern(216 Gray full window) signal toVIDEO input.(RZ-42PM10: AV4 input) refer to [fig3]
3) To adjust High Light, stick sensor to 216 Gray levelpattern, press ADJ key twice(White Balance) on remotecontrol.For adjustment and D/Eon remote control for adjustment mode to select Red Gain and Blue Gain, press Vol +.-keyand adjust it ontil color coordination becomes as below.[RF-04GA:RZ-42PM10]:
X; 0.283¡¡æ0.003, Y; 0.297¡¡æ0.003,Color Temperatuer;9,300 °K¡¡æ500°K
4) Exit adjustment mode using V Key.
4-4 Auto Adjustment Map(RS-232C)
5. DDC Data Input
5-1. Required T est Equipment(1) A j ig for adjusting PC, DDC (PC serial to D-sub
Connection equipment)(2) S/W for writing DDC (EDID Data Write & Read)(3) D-sub 15P Cable, D-Sub to DVI Connector (Connect to
DVI Jack)
5-2. Setting of Device
5-3. Preparation for Adjustment(1) Set devices as above and turn the PC, jig on.(2) Put S/W for writing DDC (EDID data Write & Read) into
operation. (operated in DOS mode.)
5-4. Sequence of Adjustment
(1) DDC Data Input for Analog-RGB1) Put the set on the table and turn the power on.2) Connect PC Serial to D-sub 15P Cable of jig for DDC
adjustment to RGB terminal (D-Sub 15Pin).3) Operate S/W for DDC record and select DDC data for
Analog RGB in Model Menu.4) Operate EDID Write command.5) Operate EDID Read command and check whether
Check Sum is OK.6) If Check Sum is NG, repeat 3) ~ 4).7) If Check Sum is OK, DDC data for Analog-RGB input is
completed.
(2) DDC Data input for Digital-RGB(DVI)1) Connect PC Serial to DVI Cable of jig for DDC
adjustment to DVI terminal (DVI Jack).2) Operate S/W for DDC record and select DDC data for
digital RGB in model menu.3) Operate EDID Write command. 4) Operate EDID Read command and check whether
Check sum is OK5) If Check sum is NG, repeat 3) ~ 4).6) If Check sum is OK, DDC data for Analog-RGB input is
completed.
PC
JIG
PDP
SET
[Fig. 3] White Balance Adjustment
Window
Pattern
AV Signal Input
COLOR
ANALYZER
TYPE; CA-100
High Light Adjustor
(216 gray pattern)
MSPG-2100 orMSTG-5200
RS-232C Ser ial Communication
Type
Baud Rate
115200
Index
R Gain
G Gain
B Gain
R Offset
G Offset
B Offset
Data bit
8
Cmd1 Cmd2
j a
j b
j c
j d
j e
j f
Stop bit
1
Parity
NONE
ProtocolSetting
Data Min Value
00(00)
00(00)
00(00)
00(00)
00(00)
00(00)
Max Value
255(FF)
255(FF)
255(FF)
255(FF)
255(FF)
255(FF)
RF-043B_PDP42
- 18 -
TROUBLE SHOOTING GUIDE
1. Power Board
1-1. The whole flowchart which it follows in voltage output state
Start check
Manufacture enterprisemeaning of a passage
1. Check the Power Offcondition.
Doesn't the screen whole come
out?
It is identical with Power Off
condition?
Yes
Yes
No
No
No
No
No
2. Check the Interfacesignal condition.
Is the Interface signal operated?
Yes
3. Check the St-by 5Vsignal circuit.
Doesn't the low pressure output
come out?
Doesn't the St-by 5V signal
come out?
Yes
Yes
No
4. Check the 5V Monitorsignal circuit.
Doesn't the 5V Monitor signal
come out?
Yes
7. Check the VSC Vs-ONsignal
Doesn't the high tension output
come out?
Doesn't the VSC signal Vs-ON
come out?
Yes
Yes
High tension output voltage Drop
it occurs?
When remove the
Y B/D Module Input Connector, output
voltage Drop it occurs?
When remove the Y, Z B/D Module
Input Connector, Power Board high tension output
voltage Drop it occurs?
Yes No No
9. Check the PowerBoard Output high
tension circuit
Yes
10. Check the Z B/DModule Coutput circuit
Yes
When remove the
Z B/D Module Input Connector, output
voltage Drop it occurs?
11. Check the Y B/DModule Coutput circuit
Yes
No
8. Check the Vs, Vavoltage output circuit.
Doesn't the Vs, Va voltage output
come out?
Yes
No
No
5. Check the VSC RL-ONsignal.
Doesn't the VSC signal RL-ON
come out?
Yes
6. Check the VSC lowpressure output
Doesn't the VSC low pressureoutput come out?
Yes
- 19 -
1-2. Sony Power Board Structure
T502: Vs Trans
T702: Va Trans
T101: St-by Trans
T103: Low Voltage Trans
1 2 3
- 20 -
1-3. Sanken Power Board Structure
T221: Vs Trans
T271: Va Trans
T121: St-by Trans
T201: Low Voltage Trans
1 2 3
- 21 -
2. No Power
(1) Symptom¯ Does’t minute discharge at module. ¯ Non does not come in into the front LED.
(2) Check follow
Is plug in power cord? Plug in power cord.
Yes
No
Is connect the Line Filter and PowerSwitch Cable?
Connect Cable.
Yes
No
Is connect the Power Switch andPower Board Cable?
Connect Cable.
Yes
No
Is normal the Fuse(F101) on PowerBoard?
Replace Fuse.
Yes
No
Is connect the Power Board and 7Pof VSC Board Cable?
Connect Cable.
Yes
No
Is connect the Power Switch andPower Board Cable?
After remove the cable connect toPower Board(except the CN101
connection cable), authorizes theAC voltage marking on manual.
When ST-BY 5V does not operate,replace Power Board.
Connect Cable.
Yes
No
- 22 -
3. Protect Mode
(1) Symptom¯ After once shining, it does not discharge minutely
from module¯ The Rely falls(The sound is audible “click”) ¯ It is converted with the color where the front LED
is red from green.
(2) Check follow
Is normal the PowerBoard?
Replace PowerBoard.
Is output the normality Low/Highvoltage except Stand-by 5V?
Yes
No No
Is normal the eachconnector?
Replaceconnector.
Replace Y-Board.
After connecting well each connector,the normality it operates?
Yes
No No
Is normal the Ctrl Board?
Replace X-Board.
Is normal the output voltage afterremove P1, 2, 101, 300, 701, 702
connector of Ctrl-B/D?
Yes
No Yes
Is normal the Y- Board?
Is normal the outputvoltage after removeP5, P6 connector of
Y-B/D?
Is normal the Fuse(F52) on Y-B/D?(In case of open is replace)
Yes
No Yes Yes
Replace Z-Board.
Is normal the Z- Board?
Is normal the outputvoltage after remove
P1 connector of Z-B/D?
Is normal the Fuse(FS1, FS2) on Z-B/D? (In case of open is replace)
Yes
No Yes
Is normal the X- Board?
Is normal the output voltage afterremove P1, 2, 3, 4, 6, 7 connector of
X-B/D?
After remove P1, P2, P3, P4 output voltagenormality: Replace Right X-B/DAfter remove P6, P7 output voltagenormality: Replace Left X-B/D
Yes
No Yes
Is normal the VSC Board?
Is normal the output voltage afterremove P1000, P1200?
After crisis COF of each board, check the normality operates.If in case normality operates, correspondence COF Fail isreplace the module.
After remove P1000 normal operation:Replace Analog BoardAfter remove P1200 normal operation:Replace Digital Board
Yes
No
Is normal the COF of X, Y, Z?
No
Yes
Yes
- 23 -
4. No Raster
(1) Symptom¯ Does’t minute discharge at module. ¯ It maintains the condition where the front LED is green.
(2) Check follow
Is normal the PowerBoard?
Replace PowerBoard.
Is output the normality Low/Highvoltage except Stand-by 5V?
Yes
No No
Is normal the eachconnector?
Replaceconnector.
Replace Y-Board.
After connecting well each connector,the normality it operates?
Yes
No No
Is normal the Ctrl Board?
Replace X-Board.
Is normal the output voltage afterremove P1, 2, 101, 300, 701, 702
connector of Ctrl-B/D?
Yes
No Yes
Is normal the Y- Board?
Is normal the outputvoltage after removeP5, P6 connector of
Y-B/D?
Is normal the Fuse(F52) on Y-B/D?(In case of open is replace)
Yes
No Yes Yes
Replace Z-Board.
Is normal the Z- Board?
Is normal the outputvoltage after remove
P1 connector of Z-B/D?
Is normal the Fuse(FS1, FS2) on Z-B/D? (In case of open is replace)
Yes
No Yes
Is normal the X- Board?
Is normal the output voltage afterremove P1, 2, 3, 4, 6, 7 connector of
X-B/D?
After remove P1, P2, P3, P4 output voltagenormality: Replace Right X-B/DAfter remove P6, P7 output voltagenormality: Replace Left X-B/D
Yes
No Yes
Is normal the VSC Board?
Is normal the output voltage afterremove P403, P1300?
After crisis COF of each board, check the normality operates.If in case normality operates, correspondence COF Fail isreplace the module.
After remove P403 normal operation:Replace AV Fix BoardAfter remove P1300 normal operation:Replace Digital Board
Yes
No
Is normal the COF of X, Y, Z?
No
Yes
Yes
- 24 -
5. In case of occur strange screen into specific mode
5-1. In case of does’t display the OSD
(1) Symptom¯ LED is green¯ The minute discharge continuously becomes accomplished from module
(2) Check follow
Is normal the LVDScable?
Is normal the VSCDigital Board?
Is the LVDS cableconnected well?
Cable inserts well.Yes
No
No
Yes
Operates the ThineIC(IC1200)?
Replace ThineIC(IC1200).
No
Is normal the CtrlBoard of Module?
Replace Ctrl B/D.No
No
Operates theIEP(IC1100)?
ReplaceIEP(IC1100).
Yes
No
Operates theScaler(IC900)?
ReplaceVSC Digital
B/D.
ReplaceScaler(IC900).
Yes Yes
No
Replace cable.Yes
- 25 -
5-2. In case of does’t display the screen into specific mode
(1) Symptom¯ The screen does not become the display from specific input mode
(RF, AV, Component, RGB, DVI).
(2) Check follow¯ Check the all input mode should become normality display.¯ Check the Video(Main)/Data(Sub), Video(Main)/Video(Sub) should become
normality display from the PIP mode or DW mode. (Re-Check it Swap)
(3) In case of becomes unusual display from RF mode
(4) In the case of becomes unusual display from RF, AV mode
Is normal the Tuner?
Is normal theCXA2069Q?
Is the Tuner Cableconnected well?
Cable inserts well.
Yes
No
No
Yes
Is normal theVPC3230?
Replace Tuner
No
Is normal the Input voltage, IICCommunication and CVBS output?
Yes
Is normal the Input voltage, IICCommunication and HV sync?
NoReplace IC
No
Is normal the Input voltage, IICCommunication and HV sync?
NoReplace IC
No
Is normal theCXA2089Q?
Yes
Is normal theVPC3230?
Is normal the Input voltage, IICCommunication and HV sync?
NoReplace IC
No
Is normal the Input voltage, IICCommunication and HV sync?
NoReplace IC
No
- 26 -
(5) In the case of becomes unusual display from RF, AV, Component 480i mode
(6) In the case of becomes unusual display from Component DTV mode
Is normal theVPC3230?
Yes
Is normal the S2300?
Is normal the Input voltage, IICCommunication and HV sync?
NoReplace IC
No
Is normal the Input voltage, IICCommunication and HV sync?
NoReplace IC
No
Yes
Is normal the Scaler?Is normal the Input voltage, IICCommunication and HV sync?
NoReplace IC
No
Is normal the74LS123?
Yes
Is normal theCXA2101?
Is normal the Input voltage, IICCommunication and HV sync?
NoReplace IC
No
Is normal the Input voltage, IICCommunication and HV sync?
NoReplace IC
No
Yes
Is normal theM52758?
Is normal the Input voltage, IICCommunication and HV sync?
NoReplace IC
No
Yes
Is normal the Scaler?Is normal the Input voltage, IICCommunication and HV sync?
NoReplace IC
No
- 27 -
(7) In the case of becomes unusual display from RGB DTV mode
(8) In the case of becomes unusual display from RGB PC mode
(8) In the case of becomes unusual display from DVI mode
Is normal theCXA2101?
Yes
Is normal theM52758?
Is normal the Input voltage, IICCommunication and HV sync?
NoReplace IC
No
Is normal the Input voltage, IICCommunication and HV sync?
NoReplace IC
No
Is normal theM52758?
Yes
Is normal the Scaler?
Is normal the Input voltage, IICCommunication and HV sync?
NoReplace IC
No
Is normal the Scaler?Is normal the Input voltage, IICCommunication and HV sync?
NoReplace IC
No
Is normal the Input voltage, IICCommunication and HV sync?
NoReplace IC
No
Yes
Is normal the Scaler?Is normal the Input voltage, IICCommunication and HV sync?
NoReplace IC
No
- 28 -
6. In case of no sound
(1) Symptom¯ LED is green¯ Screen display but sound is not output
(2) Check follow
Is normal the SPKcable?
Is the SPK cableconnected well?
Cable inserts well.
No
No
Cable inserts well.
No
Replace IC501
No
Replace IC502
No
Replace SPK cableYes
Yes
Is normal theRGB/DVI sound?
Is the Flat cableconnected well?
No
No
Operates the IC501?Yes
Operates the IC502?
Replace IC504
No
Operates the IC502?Replace
VSC Analog B/D
Yes
Yes
Yes
Is normal theRF/AV/Component
sound?
- 29 -
BLOCK DIAGRAMCable
- 30 -
BLOCK DIAGRAMCable
MEMO
- 31 -
- 32 -
EXPLODED VIEW
305
300
206
207
200
204
201
205
580
301
303
560310
210
400
101
102
501
530
520
550
540
541
601
103
201
203
302
- 33 -
EXPLODED VIEW PARTS LIST
101 5900V06008B FAN,DC G6015S12B2-RG DONGYANG 60*60*15 7V 1900RPM 6/12V L=500MM
103 4980V00D43A SUPPORTER, FAN SECC(EGI) MZ-42PM10 NCT
103 4980V00C49A SUPPORTER, FAN SECC(EGI) DULE MZ-42PM10
200 6348Q-E062A PDP, 42” 16:9 1024*768 PDP42X20000.ADLGA
201 6871QCH038A PWB(PCB) ASSEMBLY,DISPLAY CTRL ASSY HAND INSERT 42X2 CTRL LGDP4023,4013
202 6871QDH068A PWB(PCB) ASSEMBLY,DISPLAY YDRV ASSY HAND INSERT 42X2 YDRV TOP
203 6871QDH069A PWB(PCB) ASSEMBLY,DISPLAY YDRV ASSY HAND INSERT 42X2 YDRV BOTTOM
204 6871QLH037A PWB(PCB) ASSEMBLY,DISPLAY XRLT ASSY HAND INSERT 42X2 X-LEFT(TCP)
205 6871QRH043A PWB(PCB) ASSEMBLY,DISPLAY XRRT ASSY HAND INSERT 42X2 X-RIGHT (TCP)
206 6871QYH030A PWB(PCB) ASSEMBLY,DISPLAY YSUS ASSY HAND INSERT FOR 42X2
207 6871QZH034A PWB(PCB) ASSEMBLY,DISPLAY ZSUS ASSY HAND INSERT FOR 42X2
210 4980V00C62B SUPPORTER, ASSY ZDC SUPP. MODULE VERTICAL C/SKD
300 3091V00731H CABINET ASSEMBLY, 42PM12X RF043E 2TONE SKD
301 4980V00C59B SUPPORTER, ASSY EGI SUPP. FILTER TOP C/SKD
302 4980V00C61G SUPPORTER, ASSY EGI SUPP. FILTER LEFT APLLY TO MU-42PM12X SKD
303 4980V00C61F SUPPORTER, ASSY EGI SUPP. FILTER RIGHT APLLY TO MU-42PM12X SKD
305 3790V00709B FILTER(MECH), MN42PZ41 LGM42-01 MITSUI 42”” ETCHING MESH GLASS FILTER”
310 5020V01004A BUTTON, CONTROL 50PM10 6KEY
400 3809V00504B BACK COVER ASSEMBLY, MZ-42PM10 C/SKD
501 3301V00043B PLATE ASSEMBLY, ASSY 3301V00042A PLATE VSC ASSY C/SKD
520 6871VMMU20A PWB(PCB) ASSEMBLY,MAIN RF-04GA 42INCH XGA VSC B/D
530 6871VSMAAUA PWB(PCB) ASSEMBLY,SUB A/V RF04GA RCA PAL
540 6871VSMABFA PWB(PCB) ASSEMBLY,SUB PSW RF043A MAILBU
541 5020V01009B BUTTON, POWER MZ-42PM10 ABS, AF-303S 1KEY C/SKD
550 6871VSMAAVA PWB(PCB) ASSEMBLY,SUB A/V RF04GA FIX B/D
560 6871VSMT16A PWB(PCB) ASSEMBLY,SUB CONT RF04GA LOCAL KEY
580 3501V00182B POWER SUPPLY ASSEMBLY, PDP 42INCH RF043B 450W APS-208/B SANKEN
601 4980V00C71E SUPPORTER, AV INTERFACE EGI MZ-42PM10 SKD
No. Part No. Description
- 34 -
REPLACEMENT PARTS LIST
LOCA. NO PART NO DESCRIPTION
Q203
Q204
Q300
Q300
Q301
Q301
Q302
Q302
Q303
Q303
Q304
Q304
Q305
Q305
Q306
Q306
Q307
Q307
Q308
Q308
Q309
Q309
Q310
Q311
Q312
Q313
Q400
Q401
Q402
Q403
Q405
Q407
Q100
Q101
Q200
Q201
Q404
Q406
Q502
Q503
Q504
D1500
ZD100
ZD101
ZD102
ZD200
ZD201
ZD202
ZD203
D100
D101
0TR387500AA
0TR387500AA
0TR387500AA
0TR387500AA
0TR387500AA
0TR387500AA
0TR387500AA
0TR387500AA
0TR387500AA
0TR387500AA
0TR387500AA
0TR387500AA
0TR387500AA
0TR387500AA
0TR387500AA
0TR387500AA
0TR387500AA
0TR387500AA
0TR387500AA
0TR387500AA
0TR387500AA
0TR387500AA
0TR387500AA
0TR387500AA
0TR387500AA
0TR387500AA
0TR387500AA
0TR387500AA
0TR387500AA
0TR387500AA
0TR387500AA
0TR387500AA
0TR830009BA
0TR830009BA
0TR830009BA
0TR830009BA
0TR150400BA
0TR104009AF
0TR150400BA
0TR150400BA
0TR150400BA
0DD100009AM
0DR050008AA
0DR050008AA
0DR050008AA
0DR050008AA
0DR050008AA
0DR050008AA
0DR050008AA
0DD226239AA
0DD226239AA
CHIP 2SC3875S(ALY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SC3875S(ALY) KEC
BSS83 TP PHILIPS N-CHANNEL S/W TR
BSS83 TP PHILIPS N-CHANNEL S/W TR
BSS83 TP PHILIPS N-CHANNEL S/W TR
BSS83 TP PHILIPS N-CHANNEL S/W TR
CHIP 2SA1504S(ASY) KEC
CHIP KRC104S SOT-23 TP KEC
CHIP 2SA1504S(ASY) KEC
CHIP 2SA1504S(ASY) KEC
CHIP 2SA1504S(ASY) KEC
EU1ZV(1) TP SANKEN
SD05.TC R/TP SEMTECH SOD323 5V 5A 15A
SD05.TC R/TP SEMTECH SOD323 5V 5A 15A
SD05.TC R/TP SEMTECH SOD323 5V 5A 15A
SD05.TC R/TP SEMTECH SOD323 5V 5A 15A
SD05.TC R/TP SEMTECH SOD323 5V 5A 15A
SD05.TC R/TP SEMTECH SOD323 5V 5A 15A
SD05.TC R/TP SEMTECH SOD323 5V 5A 15A
CHIP KDS226 SOT-23
CHIP KDS226 SOT-23
LOCA. NO PART NO DESCRIPTION
IC1100
IC503
IC901
IC1000
IC1001
IC101
IC200
IC801
IC902
IC100
IC1200
IC300
IC400
IC500
IC501
IC502
IC504
IC800
IC1504
IC201
IC506
IC700
IC900
IC1300
IC1301
IC1302
IC1400
IC1401
IC1402
IC1403
IC1404
IC1405
IC1501
IC1502
IC301
IC400
IC401
IC505
IC1503
IC202
IC401
Q001
Q002
Q102
Q1300
Q1301
Q200
Q201
Q202
0ICTMLG018A
0IKE704200J
0IKE704200J
0IMMRHY020B
0IMMRMR023B
0IMMRAL014B
0IMMRAL014B
0IMMRHY025C
0IMMRAL025A
0IMCRSG010A
0IMCRTH002A
0ISO208900A
0IMCRMI006A
0ISO210100B
0IMCRMN028B
0IMCRNL001A
0IMCRTI028C
0IMCRGN002C
0IPRPNS054A
0IPRPBB005A
0IPRPJR017A
0IIT323000E
0IPRPGN012A
0IPRPML001A
0IMCRSJ001A
0IMCRFA010A
0IMCRSH001A
0IMCRSH001A
0IMCRRH001A
0IPRPML001A
0IMCRRH001A
0IMCRSJ001A
0IMCRKE007A
0ISH122100B
0IMCRFA010A
0IMCRSH001A
0IPRPML001A
0IMCRFA010A
0IMCRPH015A
0IMCRTI003A
0ISTLSG009A
0TR387500AA
0TR387500AA
0TR387500AA
0TR387500AA
0TR387500AA
0TR387500AA
0TR387500AA
0TR387500AA
LGDP4410 LG IC 176P TQFP
KIA7042AF SOT-89 TP 4.2V VOLTAGE
KIA7042AF SOT-89 TP 4.2V VOLTAGE
HY5DU283222AQ-5 HYNIX 100P LQFP
MX29LV800BTTC-70 MACRONIX 48P
AT24C02N-10SI-2.7 ATMEL 8P SOIC
AT24C02N-10SI-2.7 ATMEL 8P SOIC
HY57V643220DT-6 HYNIX 86P/TSOP
AT24C32AN-10SI-2.7 ATMEL 8PIN
ST3232CDR SGS-THOMSON SOP16
THC63LVD103 THINE ELECTRONICS 64P
CXA2089Q 48QFP BK A/V SWITCH
M52758FP MITSUBISHI 36PIN, R/TP PLL IC
CXA2101AQ 80P,QFP BK VIDEO
MSP4410K MICRONAS 80P/PQFP
NSP-6241B NEOFIDELITY 64P TQFP
TAS5122DCAR 56P/TSSOP R/TP 30W
FLI2300BD GENESIS 208P PQFP
LM75CIMX-3 8P/SOP R/TP
OPA3692IDBQ 16PIN SSOP
NJU26901E2 JRC 8P,EMP R/TP
VPC3230D C5 80P QFP
GM1501HBD GENESIS 416P PBGA
MIC39100 MICREL 3P SOT223
SC1565IST-1.8 3P SOT223 TP
KA7809R, FAIRCHILD 2P D-PAK
PQ05DZ1U SHARP 5, SMD TYPE
PQ05DZ1U SHARP 5, SMD TYPE
BA033FP-E2 ROHM 3P-SOP,TO252-3
MIC39100 MICREL 3P SOT223
BA033FP-E2 ROHM 3P-SOP,TO252-3
SC1565IST-1.8 SEMTECH 3P SOT223 TP
KIA278R09PI KEC TO220IS,4P ST 2A
PQ12RD21 4SIP ST REGULATOR
KA7809R, FAIRCHILD 2P D-PAK
PQ05DZ1U SHARP 5, SMD TYPE
MIC39100 MICREL 3P SOT223
KA7809R, FAIRCHILD 2P D-PAK
74LVC32AD PHILIPS 14P SOT108-1
SN74HCT08D 16P R/TP QUADRUPLE
M74HC123RM13TR 16P SOP
CHIP 2SC3875S(ALY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SC3875S(ALY) KEC
IC
TRANSISTOR
DIODE
- 35 -
LOCA. NO PART NO DESCRIPTION
D102
D103
D104
D105
D106
D107
D108
D1304
D1305
D1306
D1400
D1401
D1402
D1403
D1404
D1405
D200
D200
D201
D201
D202
D202
D203
D204
D205
D206
D207
D208
D209
D210
D211
D212
D213
D214
D215
D216
D217
D218
D219
D220
D221
D222
D300
D301
D302
D303
D304
D305
D306
D307
D308
D309
0DD226239AA
0DD226239AA
0DD226239AA
0DD226239AA
0DD226239AA
0DD226239AA
0DD184009AA
0DD226239AA
0DD226239AA
0DD226239AA
0DD226239AA
0DD226239AA
0DD226239AA
0DD226239AA
0DD226239AA
0DD226239AA
0DD226239AA
0DD226239AA
0DD226239AA
0DD226239AA
0DD226239AA
0DD226239AA
0DD226239AA
0DD226239AA
0DD226239AA
0DD226239AA
0DD226239AA
0DD226239AA
0DD226239AA
0DD226239AA
0DD226239AA
0DD226239AA
0DD226239AA
0DD226239AA
0DD226239AA
0DD226239AA
0DD226239AA
0DD226239AA
0DD226239AA
0DD226239AA
0DD226239AA
0DD226239AA
0DD226239AA
0DD226239AA
0DD226239AA
0DD226239AA
0DD226239AA
0DD226239AA
0DD226239AA
0DD226239AA
0DD226239AA
0DD226239AA
CHIP KDS226 SOT-23
CHIP KDS226 SOT-23
CHIP KDS226 SOT-23
CHIP KDS226 SOT-23
CHIP KDS226 SOT-23
CHIP KDS226 SOT-23
KDS184S CHIP 85V 300MA KEC TP
CHIP KDS226 SOT-23
CHIP KDS226 SOT-23
CHIP KDS226 SOT-23
CHIP KDS226 SOT-23
CHIP KDS226 SOT-23
CHIP KDS226 SOT-23
CHIP KDS226 SOT-23
CHIP KDS226 SOT-23
CHIP KDS226 SOT-23
CHIP KDS226 SOT-23
CHIP KDS226 SOT-23
CHIP KDS226 SOT-23
CHIP KDS226 SOT-23
CHIP KDS226 SOT-23
CHIP KDS226 SOT-23
CHIP KDS226 SOT-23
CHIP KDS226 SOT-23
CHIP KDS226 SOT-23
CHIP KDS226 SOT-23
CHIP KDS226 SOT-23
CHIP KDS226 SOT-23
CHIP KDS226 SOT-23
CHIP KDS226 SOT-23
CHIP KDS226 SOT-23
CHIP KDS226 SOT-23
CHIP KDS226 SOT-23
CHIP KDS226 SOT-23
CHIP KDS226 SOT-23
CHIP KDS226 SOT-23
CHIP KDS226 SOT-23
CHIP KDS226 SOT-23
CHIP KDS226 SOT-23
CHIP KDS226 SOT-23
CHIP KDS226 SOT-23
CHIP KDS226 SOT-23
CHIP KDS226 SOT-23
CHIP KDS226 SOT-23
CHIP KDS226 SOT-23
CHIP KDS226 SOT-23
CHIP KDS226 SOT-23
CHIP KDS226 SOT-23
CHIP KDS226 SOT-23
CHIP KDS226 SOT-23
CHIP KDS226 SOT-23
CHIP KDS226 SOT-23
LOCA. NO PART NO DESCRIPTION
D310
D400
D401
D402
ZD500
C404
C410
C553
C554
C569
C002
C1000
C1001
C1019
C115
C1300
C1305
C1306
C1308
C1318
C1322
C1323
C1325
C1326
C1330
C1331
C1332
C1335
C1336
C1338
C1351
C1354
C1355
C1356
C1402
C1403
C1418
C1419
C1420
C1422
C1423
C1424
C1427
C1428
C1441
C1443
C1444
C1445
C1446
C1450
0DD226239AA
0DD226239AA
0DD226239AA
0DD226239AA
0DZ820009AH
0CE108DJ618
0CE108DJ618
0CE108DH618
0CE108DH618
0CE108DH618
0CE476SF6DC
0CE226SF6DC
0CE226SF6DC
0CE107SF6DC
0CE476SF6DC
0CE477SF6DC
0CE227VF6DC
0CE227VF6DC
0CE477SF6DC
0CE477SF6DC
0CE477SF6DC
0CE477SF6DC
0CE227VF6DC
0CE477SF6DC
0CE227VF6DC
0CE227VF6DC
0CE107SF6DC
0CE227VF6DC
0CE227VF6DC
0CE107SF6DC
0CE476SF6DC
0CE107SF6DC
0CE107SF6DC
0CE476SF6DC
0CE477SF6DC
0CE227VF6DC
0CE107SF6DC
0CE107SF6DC
0CE107SF6DC
0CE107SF6DC
0CE107SF6DC
0CE476SF6DC
0CE477SF6DC
0CE227VF6DC
0CE107SF6DC
0CE107SF6DC
0CE107SF6DC
0CE107SF6DC
0CE107SF6DC
0CE477SF6DC
CHIP KDS226 SOT-23
CHIP KDS226 SOT-23
CHIP KDS226 SOT-23
CHIP KDS226 SOT-23
MTZJ8.2B TP ROHM-K DO34 - 8.2V 5UA
1000UF STD 35V M FL TP5
1000UF STD 35V M FL TP5
1000UF STD 25V M FL TP5
1000UF STD 25V M FL TP5
1000UF STD 25V M FL TP5
47UF MVG 16V M SMD R/TP
22UF MVG 16V 20% SMD R/TP
22UF MVG 16V 20% SMD R/TP
100UF MVG 16V M SMD R/TP
47UF MVG 16V M SMD R/TP
470UF MVG 16V 20% R/TP(SMD) SMD
220UF MV 16V 20% R/TP(SMD) SMD
220UF MV 16V 20% R/TP(SMD) SMD
470UF MVG 16V 20% R/TP(SMD) SMD
470UF MVG 16V 20% R/TP(SMD) SMD
470UF MVG 16V 20% R/TP(SMD) SMD
470UF MVG 16V 20% R/TP(SMD) SMD
220UF MV 16V 20% R/TP(SMD) SMD
470UF MVG 16V 20% R/TP(SMD) SMD
220UF MV 16V 20% R/TP(SMD) SMD
220UF MV 16V 20% R/TP(SMD) SMD
100UF MVG 16V M SMD R/TP
220UF MV 16V 20% R/TP(SMD) SMD
220UF MV 16V 20% R/TP(SMD) SMD
100UF MVG 16V M SMD R/TP
47UF MVG 16V M SMD R/TP
100UF MVG 16V M SMD R/TP
100UF MVG 16V M SMD R/TP
47UF MVG 16V M SMD R/TP
470UF MVG 16V 20% R/TP(SMD) SMD
220UF MV 16V 20% R/TP(SMD) SMD
100UF MVG 16V M SMD R/TP
100UF MVG 16V M SMD R/TP
100UF MVG 16V M SMD R/TP
100UF MVG 16V M SMD R/TP
100UF MVG 16V M SMD R/TP
47UF MVG 16V M SMD R/TP
470UF MVG 16V 20% R/TP(SMD) SMD
220UF MV 16V 20% R/TP(SMD) SMD
100UF MVG 16V M SMD R/TP
100UF MVG 16V M SMD R/TP
100UF MVG 16V M SMD R/TP
100UF MVG 16V M SMD R/TP
100UF MVG 16V M SMD R/TP
470UF MVG 16V 20% R/TP(SMD) SMD
CAPACITOR
For Capacitor & Resistors,the charactors at 2nd and 3rddigit in the P/No. means asfollows;
CC, CX, CK, CN : CeramicCQ : PolyestorCE : Electrolytic
RD : Carbon FilmRS : Metal Oxide FilmRN : Metal FilmRF : Fusible
- 36 -
LOCA. NO PART NO DESCRIPTION
C1451
C1452
C1456
C1457
C1458
C1481
C1482
C1483
C1484
C1485
C1487
C1489
C1490
C1491
C1493
C1501
C1514
C1516
C1517
C1518
C1519
C200
C210
C211
C211
C212
C212
C213
C214
C215
C216
C219
C220
C221
C221
C223
C224
C225
C227
C239
C240
C241
C242
C248
C249
C250
C300
C300
C301
C302
C303
C304
0CE477SF6DC
0CE476SF6DC
0CE476SF6DC
0CE477SF6DC
0CE477SF6DC
0CE107SF6DC
0CE476SF6DC
0CE476SF6DC
0CE476SF6DC
0CE476SF6DC
0CE476SF6DC
0CE476SF6DC
0CE476SF6DC
0CE476SF6DC
0CE477SF6DC
0CE476SF6DC
0CE476SF6DC
0CE227VF6DC
0CE105SK6DC
0CE105SK6DC
0CE105SK6DC
0CE477VF6DC
0CE476SF6DC
0CE107SF6DC
0CE476SF6DC
0CE107SF6DC
0CE476SF6DC
0CE107SF6DC
0CE107SF6DC
0CE107SF6DC
0CE107SF6DC
0CE476SF6DC
0CE475WJ6DC
0CE107SF6DC
0CE475WJ6DC
0CE477SF6DC
0CE476SF6DC
0CE477SF6DC
0CE477SF6DC
0CE105SK6DC
0CE105SK6DC
0CE105SK6DC
0CE105SK6DC
0CE475WJ6DC
0CE475WJ6DC
0CE477VF6DC
0CE476SF6DC
0CE105SK6DC
0CE105SK6DC
0CE105SK6DC
0CE105SK6DC
0CE105SK6DC
470UF MVG 16V 20% R/TP(SMD) SMD
47UF MVG 16V M SMD R/TP
47UF MVG 16V M SMD R/TP
470UF MVG 16V 20% R/TP(SMD) SMD
470UF MVG 16V 20% R/TP(SMD) SMD
100UF MVG 16V M SMD R/TP
47UF MVG 16V M SMD R/TP
47UF MVG 16V M SMD R/TP
47UF MVG 16V M SMD R/TP
47UF MVG 16V M SMD R/TP
47UF MVG 16V M SMD R/TP
47UF MVG 16V M SMD R/TP
47UF MVG 16V M SMD R/TP
47UF MVG 16V M SMD R/TP
470UF MVG 16V 20% R/TP(SMD) SMD
47UF MVG 16V M SMD R/TP
47UF MVG 16V M SMD R/TP
220UF MV 16V 20% R/TP(SMD) SMD
1UF MVG 50V M SMD R/TP
1UF MVG 50V M SMD R/TP
1UF MVG 50V M SMD R/TP
470UF MV 16V 20% R/TP(SMD) SMD
47UF MVG 16V M SMD R/TP
100UF MVG 16V M SMD R/TP
47UF MVG 16V M SMD R/TP
100UF MVG 16V M SMD R/TP
47UF MVG 16V M SMD R/TP
100UF MVG 16V M SMD R/TP
100UF MVG 16V M SMD R/TP
100UF MVG 16V M SMD R/TP
100UF MVG 16V M SMD R/TP
47UF MVG 16V M SMD R/TP
4.7UF MVK 35V 20% R/TP(SMD) SMD
100UF MVG 16V M SMD R/TP
4.7UF MVK 35V 20% R/TP(SMD) SMD
470UF MVG 16V 20% R/TP(SMD) SMD
47UF MVG 16V M SMD R/TP
470UF MVG 16V 20% R/TP(SMD) SMD
470UF MVG 16V 20% R/TP(SMD) SMD
1UF MVG 50V M SMD R/TP
1UF MVG 50V M SMD R/TP
1UF MVG 50V M SMD R/TP
1UF MVG 50V M SMD R/TP
4.7UF MVK 35V 20% R/TP(SMD) SMD
4.7UF MVK 35V 20% R/TP(SMD) SMD
470UF MV 16V 20% R/TP(SMD) SMD
47UF MVG 16V M SMD R/TP
1UF MVG 50V M SMD R/TP
1UF MVG 50V M SMD R/TP
1UF MVG 50V M SMD R/TP
1UF MVG 50V M SMD R/TP
1UF MVG 50V M SMD R/TP
LOCA. NO PART NO DESCRIPTION
C305
C305
C308
C309
C310
C313
C314
C315
C319
C335
C336
C337
C339
C343
C344
C345
C347
C400
C404
C405
C406
C406
C407
C408
C409
C411
C412
C415
C416
C417
C418
C420
C423
C426
C427
C429
C431
C434
C437
C500
C501
C506
C507
C513
C514
C515
C516
C517
C517
C522
C525
C530
0CE476SF6DC
0CE105SK6DC
0CE105SK6DC
0CE476SF6DC
0CE105SK6DC
0CE105SK6DC
0CE105SK6DC
0CE105SK6DC
0CE105SK6DC
0CE476SF6DC
0CE476SF6DC
0CE476SF6DC
0CE476SF6DC
0CE476SF6DC
0CE476SF6DC
0CE476SF6DC
0CE476SF6DC
0CE476SF6DC
0CE476SF6DC
0CE476SF6DC
0CE476SF6DC
0CE227VF6DC
0CE477SF6DC
0CE477SF6DC
0CE477SF6DC
0CE227VF6DC
0CE476XFKDC
0CE476XFKDC
0CE476XFKDC
0CE227VF6DC
0CE106SF6DC
0CE107SF6DC
0CE476SF6DC
0CE477SF6DC
0CE107SF6DC
0CE107SF6DC
0CE477SF6DC
0CE476SF6DC
0CE107SF6DC
0CE476SF6DC
0CE476SF6DC
0CE335SK6DC
0CE335SK6DC
0CE106SF6DC
0CE106SF6DC
0CE107SF6DC
0CE105SK6DC
0CE107SF6DC
0CE226SF6DC
0CE107SF6DC
0CE226VF6DC
0CE107SF6DC
47UF MVG 16V M SMD R/TP
1UF MVG 50V M SMD R/TP
1UF MVG 50V M SMD R/TP
47UF MVG 16V M SMD R/TP
1UF MVG 50V M SMD R/TP
1UF MVG 50V M SMD R/TP
1UF MVG 50V M SMD R/TP
1UF MVG 50V M SMD R/TP
1UF MVG 50V M SMD R/TP
47UF MVG 16V M SMD R/TP
47UF MVG 16V M SMD R/TP
47UF MVG 16V M SMD R/TP
47UF MVG 16V M SMD R/TP
47UF MVG 16V M SMD R/TP
47UF MVG 16V M SMD R/TP
47UF MVG 16V M SMD R/TP
47UF MVG 16V M SMD R/TP
47UF MVG 16V M SMD R/TP
47UF MVG 16V M SMD R/TP
47UF MVG 16V M SMD R/TP
47UF MVG 16V M SMD R/TP
220UF MV 16V 20% R/TP(SMD) SMD
470UF MVG 16V 20% R/TP(SMD) SMD
470UF MVG 16V 20% R/TP(SMD) SMD
470UF MVG 16V 20% R/TP(SMD) SMD
220UF MV 16V 20% R/TP(SMD) SMD
47UF MVK-BP,CN 16V 20%,-20% SMD
47UF MVK-BP,CN 16V 20%,-20% SMD
47UF MVK-BP,CN 16V 20%,-20% SMD
220UF MV 16V 20% R/TP(SMD) SMD
10UF MVG 16V 20% R/TP(SMD) SMD
100UF MVG 16V M SMD R/TP
47UF MVG 16V M SMD R/TP
470UF MVG 16V 20% R/TP(SMD) SMD
100UF MVG 16V M SMD R/TP
100UF MVG 16V M SMD R/TP
470UF MVG 16V 20% R/TP(SMD) SMD
47UF MVG 16V M SMD R/TP
100UF MVG 16V M SMD R/TP
47UF MVG 16V M SMD R/TP
47UF MVG 16V M SMD R/TP
3.3UF MVG 50V 20% SMD R/TP
3.3UF MVG 50V 20% SMD R/TP
10UF MVG 16V 20% R/TP(SMD) SMD
10UF MVG 16V 20% R/TP(SMD) SMD
100UF MVG 16V M SMD R/TP
1UF MVG 50V M SMD R/TP
100UF MVG 16V M SMD R/TP
22UF MVG 16V 20% SMD R/TP
100UF MVG 16V M SMD R/TP
22UF MV 16V 20% R/TP(SMD) SMD
100UF MVG 16V M SMD R/TP
For Capacitor & Resistors,the charactors at 2nd and 3rddigit in the P/No. means asfollows;
CC, CX, CK, CN : CeramicCQ : PolyestorCE : Electrolytic
RD : Carbon FilmRS : Metal Oxide FilmRN : Metal FilmRF : Fusible
- 37 -
LOCA. NO PART NO DESCRIPTION
C534
C536
C538
C540
C705
C709
C714
C730
C827
C833
C904
C905
C906
C908
C909
C910
C911
C912
C913
C919
C920
C921
C567
C568
C411
C545
C549
L1300
L1301
L1302
L1303
L400
L401
L402
L507
L508
L509
L510
P101
P200
P201
P500
R1530
R801
R802
RA1100
0CE106SF6DC
0CE106SF6DC
0CE106SF6DC
0CE106SF6DC
0CE107SF6DC
0CE106SF6DC
0CE106SF6DC
0CE106SF6DC
0CE107SF6DC
0CE107SF6DC
0CE335SK6DC
0CE226SF6DC
0CE226SF6DC
0CE226SF6DC
0CE226SF6DC
0CE226SF6DC
0CE226SF6DC
0CE226SF6DC
0CE226SF6DC
0CE226SF6DC
0CE226SF6DC
0CE226SF6DC
0CF4741L438
0CF4741L438
0CN105EJ56A
0CN105EJ56A
0CN105EJ56A
6140VB0004B
6140VB0004B
6140VB0004B
6140VB0004B
6140VB0004B
6140VB0004B
6140VB0004B
6140VB0024A
6140VB0024A
6140VB0024A
6140VB0024A
6630VGA004B
6630VGA001C
6630VGA001C
385-173B
0RD0152H609
0RKZVTA001L
0RKZVTA001L
0RRZVTA001D
10UF MVG 16V 20% R/TP(SMD) SMD
10UF MVG 16V 20% R/TP(SMD) SMD
10UF MVG 16V 20% R/TP(SMD) SMD
10UF MVG 16V 20% R/TP(SMD) SMD
100UF MVG 16V M SMD R/TP
10UF MVG 16V 20% R/TP(SMD) SMD
10UF MVG 16V 20% R/TP(SMD) SMD
10UF MVG 16V 20% R/TP(SMD) SMD
100UF MVG 16V M SMD R/TP
100UF MVG 16V M SMD R/TP
3.3UF MVG 50V 20% SMD R/TP
22UF MVG 16V 20% SMD R/TP
22UF MVG 16V 20% SMD R/TP
22UF MVG 16V 20% SMD R/TP
22UF MVG 16V 20% SMD R/TP
22UF MVG 16V 20% SMD R/TP
22UF MVG 16V 20% SMD R/TP
22UF MVG 16V 20% SMD R/TP
22UF MVG 16V 20% SMD R/TP
22UF MVG 16V 20% SMD R/TP
22UF MVG 16V 20% SMD R/TP
22UF MVG 16V 20% SMD R/TP
0.47UF D 63V 5% TP 5 M/PE NI
0.47UF D 63V 5% TP 5 M/PE NI
1.0UF 3216 35V 10% R/TP X7R
1.0UF 3216 35V 10% R/TP X7R
1.0UF 3216 35V 10% R/TP X7R
26UH 1UEWPHY 22.5TURN YL-9N 0.4
26UH 1UEWPHY 22.5TURN YL-9N 0.4
26UH 1UEWPHY 22.5TURN YL-9N 0.4
26UH 1UEWPHY 22.5TURN YL-9N 0.4
26UH 1UEWPHY 22.5TURN YL-9N 0.4
26UH 1UEWPHY 22.5TURN YL-9N 0.4
26UH 1UEWPHY 22.5TURN YL-9N 0.4
LPK-1322A SOOJUNG 22UH +-10%
LPK-1322A SOOJUNG 22UH +-10%
LPK-1322A SOOJUNG 22UH +-10%
LPK-1322A SOOJUNG 22UH +-10%
69107-0921 9P 2.77MM
68114-1521 15PIN 2.29MM ANGLE SN
68114-1521 15PIN 2.29MM ANGLE SN
VER TYPE(2LINE 4P A+B)
15 OHM 1/2 W 5.00% TA52
1.0M OHM 1/2 W 5% TA52 UL PILKOR
1.0M OHM 1/2 W 5% TA52 UL PILKOR
22 OHM 1 / 16 W 1608 5% R/TP 4P E24
LOCA. NO PART NO DESCRIPTION
RA1101
RA1102
RA1103
RA1104
RA1105
RA1106
RA700
RA701
RA702
RA703
RA800
RA801
RA803
RA805
RA806
RA807
RA808
RA809
RA810
RA811
RA812
RA813
RA814
RA815
RA816
RA817
RA818
RA900
RA901
RA902
RA903
RA904
RA905
RA906
RA907
RA908
RA909
RA910
RA911
RA912
D1301
D1302
D1303
LD001
LED400
LED401
LED402
SW001
0RRZVTA001D
0RRZVTA001D
0RRZVTA001D
0RRZVTA001D
0RRZVTA001D
0RRZVTA001D
0RRZVTA001D
0RRZVTA001D
0RRZVTA001D
0RRZVTA001D
0RRZVTA001D
0RRZVTA001D
0RRZVTA001D
0RRZVTA001D
0RRZVTA001D
0RRZVTA001D
0RRZVTA001D
0RRZVTA001D
0RRZVTA001D
0RRZVTA001D
0RRZVTA001D
0RRZVTA001D
0RRZVTA001D
0RRZVTA001D
0RRZVTA001D
0RRZVTA001D
0RRZVTA001D
0RRZVTA001D
0RRZVTA001D
0RRZVTA001D
0RRZVTA001D
0RRZVTA001D
0RRZVTA001D
0RRZVTA001D
0RRZVTA001D
0RRZVTA001D
0RRZVTA001D
0RRZVTA001D
0RRZVTA001D
0RRZVTA001D
0DL233309AC
0DL233309AC
0DL233309AC
0DL200000CA
0DL233309AC
0DL233309AC
0DL233309AC
140-313B
22 OHM 1 / 16 W 1608 5% R/TP 4P E24
22 OHM 1 / 16 W 1608 5% R/TP 4P E24
22 OHM 1 / 16 W 1608 5% R/TP 4P E24
22 OHM 1 / 16 W 1608 5% R/TP 4P E24
22 OHM 1 / 16 W 1608 5% R/TP 4P E24
22 OHM 1 / 16 W 1608 5% R/TP 4P E24
22 OHM 1 / 16 W 1608 5% R/TP 4P E24
22 OHM 1 / 16 W 1608 5% R/TP 4P E24
22 OHM 1 / 16 W 1608 5% R/TP 4P E24
22 OHM 1 / 16 W 1608 5% R/TP 4P E24
22 OHM 1 / 16 W 1608 5% R/TP 4P E24
22 OHM 1 / 16 W 1608 5% R/TP 4P E24
22 OHM 1 / 16 W 1608 5% R/TP 4P E24
22 OHM 1 / 16 W 1608 5% R/TP 4P E24
22 OHM 1 / 16 W 1608 5% R/TP 4P E24
22 OHM 1 / 16 W 1608 5% R/TP 4P E24
22 OHM 1 / 16 W 1608 5% R/TP 4P E24
22 OHM 1 / 16 W 1608 5% R/TP 4P E24
22 OHM 1 / 16 W 1608 5% R/TP 4P E24
22 OHM 1 / 16 W 1608 5% R/TP 4P E24
22 OHM 1 / 16 W 1608 5% R/TP 4P E24
22 OHM 1 / 16 W 1608 5% R/TP 4P E24
22 OHM 1 / 16 W 1608 5% R/TP 4P E24
22 OHM 1 / 16 W 1608 5% R/TP 4P E24
22 OHM 1 / 16 W 1608 5% R/TP 4P E24
22 OHM 1 / 16 W 1608 5% R/TP 4P E24
22 OHM 1 / 16 W 1608 5% R/TP 4P E24
22 OHM 1 / 16 W 1608 5% R/TP 4P E24
22 OHM 1 / 16 W 1608 5% R/TP 4P E24
22 OHM 1 / 16 W 1608 5% R/TP 4P E24
22 OHM 1 / 16 W 1608 5% R/TP 4P E24
22 OHM 1 / 16 W 1608 5% R/TP 4P E24
22 OHM 1 / 16 W 1608 5% R/TP 4P E24
22 OHM 1 / 16 W 1608 5% R/TP 4P E24
22 OHM 1 / 16 W 1608 5% R/TP 4P E24
22 OHM 1 / 16 W 1608 5% R/TP 4P E24
22 OHM 1 / 16 W 1608 5% R/TP 4P E24
22 OHM 1 / 16 W 1608 5% R/TP 4P E24
22 OHM 1 / 16 W 1608 5% R/TP 4P E24
22 OHM 1 / 16 W 1608 5% R/TP 4P E24
SAM2333 GREEN/RED GREEN:10MCD, RED:6MCD
SAM2333 GREEN/RED GREEN:10MCD, RED:6MCD
SAM2333 GREEN/RED GREEN:10MCD, RED:6MCD
SAM5670(DL-2LRG) BK Y-GREEN
SAM2333 GREEN/RED GREEN:10MCD, RED:6MCD
SAM2333 GREEN/RED GREEN:10MCD, RED:6MCD
SAM2333 GREEN/RED GREEN:10MCD, RED:6MCD
TACT 2LEAD 160G(TA) LG C&D
For Capacitor & Resistors,the charactors at 2nd and 3rddigit in the P/No. means asfollows;
CC, CX, CK, CN : CeramicCQ : PolyestorCE : Electrolytic
RD : Carbon FilmRS : Metal Oxide FilmRN : Metal FilmRF : Fusible
LED
COIL
CONNECTOR
RESISTOR
SWITCH
FBMH3216 HM501NT 3.2X1.6X1.6MM R/TP
FBMH3216 HM501NT 3.2X1.6X1.6MM R/TP
BK2125 HS 750 2X1.25X0.85MM R/TP
FBMH3216 HM501NT 3.2X1.6X1.6MM R/TP
FBMH3216 HM501NT 3.2X1.6X1.6MM R/TP
FBMH3216 HM501NT 3.2X1.6X1.6MM R/TP
FBMH3216 HM501NT 3.2X1.6X1.6MM R/TP
FBMH3216 HM501NT 3.2X1.6X1.6MM R/TP
FBMH3216 HM501NT 3.2X1.6X1.6MM R/TP
FBMH3216 HM501NT 3.2X1.6X1.6MM R/TP
FBMH3216 HM501NT 3.2X1.6X1.6MM R/TP
FBMH3216 HM501NT 3.2X1.6X1.6MM R/TP
FBMH3216 HM501NT 3.2X1.6X1.6MM R/TP
FBMH3216 HM501NT 3.2X1.6X1.6MM R/TP
FBMH3216 HM501NT 3.2X1.6X1.6MM R/TP
FBMH3216 HM501NT 3.2X1.6X1.6MM R/TP
FBMH3216 HM501NT 3.2X1.6X1.6MM R/TP
FBMH3216 HM501NT 3.2X1.6X1.6MM R/TP
FBMH3216 HM501NT 3.2X1.6X1.6MM R/TP
MLB-201209-1000L-N2 R/TP 1000OHM 350MA
BK2125 HS 750 2X1.25X0.85MM R/TP
MLB-201209-1000L-N2 R/TP 1000OHM 350MA
BK2125 HS 750 2X1.25X0.85MM R/TP
BK2125 HS 750 2X1.25X0.85MM R/TP
FBMH3216 HM501NT 3.2X1.6X1.6MM R/TP
RESONATOR,CRYSTAL HC49U 18.432MHZ 30PPM
RESONATOR,CRYSTAL SX-1SMD 20250000HZ
RESONATOR,CRYSTAL SX-1 13.500000MHZ
RESONATOR,CRYSTAL SX-1 SC14.3MHZ
UEJ-CV-018 UGCOM D3.5 E/P
440062-1 AMP DVI INTERACED
UEJ-CV-018 UGCOM D3.5 E/P
PPJ128A-1 A/V 2P MONO GN-BL-RD
PPJ121-22 A/V 4P FOR EMI WITH SWITCH RED
PJ6046G PARKELEC H=8.0 W/O
UPJ-R1-023 UGCOM 21PIN W/SHLD
UPJ-R1-023 UGCOM 21PIN W/SHLD
MANUAL,OWNERSRF04GA PM10 138D TX 026H
REMOTE CONTROLLERRF04GA MZ-42PM10 40
POWER CORDM2511A-001 2800MM PLUG IVORY
CABLE,DVILVDS UL20276 AWG30 500MM
FUSE,SLOW BLOW 10000MA 250 V 5.2X20
- 38 -
LOCA. NO PART NO DESCRIPTION
SW002
SW003
SW004
SW005
SW006
SW800
SW900
F100
F101
F102
F103
F500
F501
F502
L100
L1000
L101
L102
L103
L104
L105
L106
L1305
L1307
L1308
L1309
L1400
L1401
L1402
L1404
L1405
L1406
L1409
L1410
L1412
L1413
L1414
L1415
L1416
L1417
L1418
L1419
L1420
L1421
L1422
L1423
L1424
L1425
L1426
L1427
140-313B
140-313B
140-313B
140-313B
140-313B
6600VM2006A
140-313B
6200J00012A
6200J00012A
6200J00012A
6200J00012A
6200VJS001A
6200VJS001B
6200VJS001B
6210VC0006A
6210VC0006A
6210VC0006A
6200JB8010L
6200JB8010L
6200JB8010L
6200JB8010L
6210VC0006A
6210VC0006A
6210VC0006A
6210VC0006A
6210VC0006A
6210VC0006A
6210VC0006A
6210VC0006A
6210VC0006A
6210VC0006A
6210VC0006A
6210VC0006A
6210VC0006A
6210VC0006A
6210VC0006A
6210VC0006A
6210VC0006A
6210VC0006A
6210VC0006A
6210VC0006A
6210VC0006A
6210VC0006A
6210VC0006A
6210VC0006A
6210VC0006A
6210VC0006A
6210VC0006A
6210VC0006A
6210VC0006A
TACT 2LEAD 160G(TA) LG C&D
TACT 2LEAD 160G(TA) LG C&D
TACT 2LEAD 160G(TA) LG C&D
TACT 2LEAD 160G(TA) LG C&D
TACT 2LEAD 160G(TA) LG C&D
SDDF3PATP011 250V 4A HORIZONTAL .G
TACT 2LEAD 160G(TA) LG C&D
ACM2012-900H-2P TDK R/TP
ACM2012-900H-2P TDK R/TP
ACM2012-900H-2P TDK R/TP
ACM2012-900H-2P TDK R/TP
ZJY51R5-4P TDK DIP DC 50VOLT 2A
ZJYS51R5-2PL(T) TDK R/TP 50VOLT 2A
ZJYS51R5-2PL(T) TDK R/TP 50VOLT 2A
FBMH3216 HM501NT 3.2X1.6X1.6MM R/TP
FBMH3216 HM501NT 3.2X1.6X1.6MM R/TP
FBMH3216 HM501NT 3.2X1.6X1.6MM R/TP
MLB-201209-1000L-N2 R/TP 1000OHM 350MA
MLB-201209-1000L-N2 R/TP 1000OHM 350MA
MLB-201209-1000L-N2 R/TP 1000OHM 350MA
MLB-201209-1000L-N2 R/TP 1000OHM 350MA
FBMH3216 HM501NT 3.2X1.6X1.6MM R/TP
FBMH3216 HM501NT 3.2X1.6X1.6MM R/TP
FBMH3216 HM501NT 3.2X1.6X1.6MM R/TP
FBMH3216 HM501NT 3.2X1.6X1.6MM R/TP
FBMH3216 HM501NT 3.2X1.6X1.6MM R/TP
FBMH3216 HM501NT 3.2X1.6X1.6MM R/TP
FBMH3216 HM501NT 3.2X1.6X1.6MM R/TP
FBMH3216 HM501NT 3.2X1.6X1.6MM R/TP
FBMH3216 HM501NT 3.2X1.6X1.6MM R/TP
FBMH3216 HM501NT 3.2X1.6X1.6MM R/TP
FBMH3216 HM501NT 3.2X1.6X1.6MM R/TP
FBMH3216 HM501NT 3.2X1.6X1.6MM R/TP
FBMH3216 HM501NT 3.2X1.6X1.6MM R/TP
FBMH3216 HM501NT 3.2X1.6X1.6MM R/TP
FBMH3216 HM501NT 3.2X1.6X1.6MM R/TP
FBMH3216 HM501NT 3.2X1.6X1.6MM R/TP
FBMH3216 HM501NT 3.2X1.6X1.6MM R/TP
FBMH3216 HM501NT 3.2X1.6X1.6MM R/TP
FBMH3216 HM501NT 3.2X1.6X1.6MM R/TP
FBMH3216 HM501NT 3.2X1.6X1.6MM R/TP
FBMH3216 HM501NT 3.2X1.6X1.6MM R/TP
FBMH3216 HM501NT 3.2X1.6X1.6MM R/TP
FBMH3216 HM501NT 3.2X1.6X1.6MM R/TP
FBMH3216 HM501NT 3.2X1.6X1.6MM R/TP
FBMH3216 HM501NT 3.2X1.6X1.6MM R/TP
FBMH3216 HM501NT 3.2X1.6X1.6MM R/TP
FBMH3216 HM501NT 3.2X1.6X1.6MM R/TP
FBMH3216 HM501NT 3.2X1.6X1.6MM R/TP
FBMH3216 HM501NT 3.2X1.6X1.6MM R/TP
LOCA. NO PART NO DESCRIPTION
6210VC0006A
6210VC0006A
6210VC0005A
6210VC0006A
6210VC0006A
6210VC0006A
6210VC0006A
6210VC0006A
6210VC0006A
6210VC0006A
6210VC0006A
6210VC0006A
6210VC0006A
6210VC0006A
6210VC0006A
6210VC0006A
6210VC0006A
6210VC0006A
6210VC0006A
6200JB8010L
6210VC0005A
6200JB8010L
6210VC0005A
6210VC0005A
6210VC0006A
156-A02M
6202VDT002E
6202VDT002J
6202VDT002B
380-068E
6612BBBHN6A
380-068E
6612J00010A
6612VJH019C
380-363K
6612M00001A
6612M00001A
3828VA0513F
6710V00138D
6410VEH003C
6850J00005A
0FS1002B53K
L1428
L201
L205
L209
L210
L303
L304
L305
L401
L402
L403
L404
L405
L406
L407
L500
L501
L502
L503
L504
L504
L505
L505
L506
L900
X500
X700
X800
X900
P100
P102
P103
P200
P201
P202
P203
P204
A1
A2
A3
A4
F801
JACK
MISCELLANEOUS
ACCESSORIES
FILTER & CRYSTAL
PRINTED CIRCUIT BOARD
MAIN (TOP)
CONTROL
MAIN (BOTTOM )
A/V FIX B/D(TOP) A/V FIX B/D(TOP) A/V RCA PAL(ToOP)
A/V RCA PAL(BOTT OM)
Dec., 2004Printed in KoreaP/NO : 3828VD0198N