Lifting Beams

Other sizes available, consult factory.

Model 20 - Low Headroom Multiple Spread Lifting BeamIdeal where headroom is limited. PRODUCT FEATURES:

• Beams over 6’ and longer have 3 spreads.• 3’ & 4’ beams have 2 spreads.• Swivel hooks with hook latches standard.• Wide range of sizes and capacities available.• Complies with ASME standards.

STANDARD FEATURE:Three spreads to adjust to the load

- Outside spread- Middle spread (outside less 1’)- Inside spread (outside less 2’)

A.8

SPECIFICATIONSModel Number Outside Spread (feet)

Capacity HR Headroom (in.)(tons) Weight (lbs.) 3 4 6 8 10 12

Model Number 20-1/2-3 20-1/2-4 20-1/2-6 20-1/2-8 20-1/2-10 20-1/2-121/2 HR Headroom 12-3/4 12-3/4 12-3/4 12-3/4 13-3/4 13-3/4

Weight 40 50 65 95 140 160Model Number 20-1-3 20-1-4 20-1-6 20-1-8 20-1-10 20-1-12

1 HR Headroom 12-3/4 12-3/4 13-3/4 13-3/4 14-3/4 15-3/4Weight 40 50 85 115 165 230

Model Number 20-2-3 20-2-4 20-2-6 20-2-8 20-2-10 20-2-122 HR Headroom 13-3/4 13-3/4 14-3/4 16-1/2 17-1/2 18-1/4

Weight 50 65 100 165 230 315Model Number 20-3-3 20-3-4 20-3-6 20-3-8 20-3-10 20-3-12

3 HR Headroom 15-1/4 15-1/4 16-1/4 17-1/4 18-1/4 22-1/2Weight 70 80 140 200 275 415

Model Number 20-5-3 20-5-4 20-5-6 20-5-8 20-5-10 20-5-125 HR Headroom 19-1/2 20-1/2 21-1/2 25-1/2 25-1/2 27-1/2

Weight 115 145 205 325 390 580Model Number 20-7 1/2-3 20-7 1/2-4 20-7 1/2-6 20-7 1/2-8 20-7 1/2-10 20-7 1/2-12

7-1/2 HR Headroom 22-1/2 23-1/2 25-1/4 27-1/4 27-1/4 30-1/4Weight 135 170 265 415 500 910

Model Number 20-10-3 20-10-4 20-10-6 20-10-8 20-10-10 20-10-1210 HR Headroom 23-1/4 25-1/4 27-1/4 27-1/4 30-1/4 30-1/4

Weight 150 205 335 420 775 910Model Number 20-15-3 20-15-4 20-15-6 20-15-8 20-15-10 20-15-12

15 HR Headroom 28-1/2 30-1/2 30-1/2 33-1/2 33-1/2 40-1/4Weight 215 295 375 685 820 1180

Model Number 20-20-3 20-20-4 20-20-6 20-20-8 20-20-10 20-20-1220 HR Headroom 38-3/4 38-3/4 38-3/4 38-3/4 41-1/2 41-1/2

Weight 370 435 575 710 1070 1235Model Number 20-25-4 20-25-6 20-25-8 20-25-10 20-25-12

25 HR Headroom 41-3/8 41-3/8 44-3/8 44-3/8 44-3/8Weight 470 590 925 1100 1650

Model Number 20-30-4 20-30-6 20-30-830 HR Headroom 45-1/2 45-1/2 48-1/4

Weight 525 660 1010Model Number 20-40-4 20-40-6

40 HR Headroom 44-3/4 47-3/4Weight 600 930

Strong-Bac

®Section

2014-2016 Master C

atalogT

he

Ca

ldw

ell G

rou

p• 800-628-4263 • w

ww

.caldwellinc.com

Lifting Beams

OPTION BFaspinsFor ease of positioning hooks with quick release. Specify number required.

OPTION CExtra HooksAllows for multiple pick points. Specify number required.

OPTION DPin Type BailLifting pin located between structural channel. (Hoist hookinformation must be supplied.)

OPTION EShackle LugLifting lug with shackle. (Headroom may change.)

Recommend faspins (Option B) if frequent hook position changes (spread) are required.

Outside Spread (feet )Other

14 16 18 20 24 30 Dimensions (in.)

20-1/2-14 20-1/2-16 20-1/2-18 20-1/2-20 20-1/2-24 20-1/2-30 A=7/814-3/4 15-3/4 16-3/4 16-3/4 20-1/4 22-1/4 B=3

230 305 400 450 830 1340 C=520-1-14 20-1-16 20-1-18 20-1-20 20-1-24 A=7/816-3/4 18-1/2 20-1/4 20-1/4 22-1/4 B=3

320 415 605 675 1095 C=520-2-14 20-2-16 20-2-18 20-2-20 20-2-24 A=7/820-1/4 20-1/4 24-3/4 24-3/4 27-3/4 B=3

480 540 800 900 1730 C=520-3-14 20-3-16 20-3-18 20-3-20 20-3-24 A=1-1/424-1/2 24-1/2 27-1/2 27-1/2 27-1/2 B=3

650 730 1295 1450 1765 C=520-5-14 20-5-16 20-5-18 20-5-20 20-5-24 A=227-1/2 30-1/4 30-1/4 30-1/4 33-1/4 B=4

690 1210 1340 1505 2275 C=720-7 1/2-14 20-7 1/2-16 20-7 1/2-18 A=2

30-1/4 30-1/4 33 B=41070 1600 1665 C=7

20-10-14 20-10-16 20-10-18 A=230-1/4 33 33 B=41075 1500 1670 C=7

20-15-14 A=2-1/240-1/4 B=51385 C=9

A=2-1/2B=5C=9A=3B=6C=12A=3-1/2B=7C=16A=3-1/2B=7C=16

A.9

SPECIFICATIONS

T=3/4O=7/8

T=3/4O=7/8

T=3/4O=7/8

T=1O=1

T=1-1/4O=1-15/16

T=1-1/4O=1-1/2

T=1-1/4O=1-9/16

T=1-1/2O=2-1/16

T=1-1/2O=2-1/4

T=1-3/4O=2-1/4

T=2O=2-1/4

T=2-1/2O=3

See pages A.10 and A.11 forthese capacities and sizes.

OPTION AExtra Holes or DifferentPlacement of HolesAllows multiple hook positioning beyond standard spreads. Specifynumber and spread(s) required.

Strong-Bac

®Section

2014-2016 Master C

atalogT

he

Ca

ldw

ell G

rou

p• 800-628-4263 • w

ww

.caldwellinc.com

Paper Roll Lifters/Positioners

A.33

Model 23 - Roll Lifting Beams

OPTION ESPREADER BEAMOffers greater stabilitywhen required headroomis not a consideration.

OPTION AADJUSTABLE SPREADSUsed when handling rolls ofvarying widths.

OPTION BHOOK LININGSa. Bronze/Brassb. Urethanec. Brake Lining

(Min. Shaft Dia.= 6”)

OPTION C TWIN BAILSUsed when two hoistsare required to stabilizea lift, when load rotationis not desirable.

OPTION DMOTORIZED ROTATIONAllows remote positioning of a load. For additionalinformation, see Model 21 on page A.20.

Options Available

PRODUCT FEATURES:• Ideal where headroom is limited.• Easy lifting and positioning of rolls.• Adjustable spread options.• Twin hoist capability.• Motorized rotation available.• Complies with ASME standards.

Used to lift rolls with plate style or bent bar J-Hooks. Hooks are designed to support the core mandrel which isthrough the I.D. of the roll. Fixed beam lengths can be used for single roll widths. Maximum roll diameters willdetermine length of J-Hooks.

Strong-Bac

®Section

2014-2016 Master C

atalogT

he

Ca

ldw

ell G

rou

p• 800-628-4263 • w

ww

.caldwellinc.com

Lifting Beams

A.14

Model 24 - Adjustable Bail Lifting Beam

OPTION A*EXTRA HOLESAllows for multiple hookpositioning. Specify numberand spread(s) required. *Could increase headroom.

CO

B A

HR

T

E E

DTYP. SPREAD

SPECIFICATIONS

OPTION BFASPINSFor ease of positioning hooks with quick release.Specify number of faspins required.

OPTION CEXTRA HOOKSAllows for multiple pick points. Specify numberof hooks required.

OPTION DPIN TYPE BAIL Lifting pin located betweenstructural channel. (Hoist hook information mustbe supplied.)

PRODUCT FEATURES:• Handles off center loads by adjusting the bail before a lift.• Adjustable spread options available.• Swivel hooks with hook latches standard.• Wide range of sizes and capacities available.• Complies with ASME standards.

Rated Model Number Spread (feet)Capacity HR Headroom (in.) Other(tons) Weight (lbs.) 3 4 6 8 10 12 14 16 18 20 Dimensions (in.)

Model Number 24-1/2-3 24-1/2-4 24-1/2-6 24-1/2-8 24-1/2-10 24-1/2-12 24-1/2-14 24-1/2-16 24-1/2-18 24-1/2-201/2 HR Headroom 13-1/2 13-1/2 13-1/2 12-5/8 13-1/2 13-1/2 13-1/2 14-1/2 14-1/2 14-1/2

Weight 47 56 75 82 95 147 168 255 278 304Model Number 24-1-3 24-1-4 24-1-6 24-1-8 24-1-10 24-1-12 24-1-14 24-1-16 24-1-18 24-1-20

1 HR Headroom 13-1/2 13-5/8 13-5/8 14-5/8 14-5/8 14-5/8 15-5/8 15-5/8 16-1/2 16-1/2Weight 47 56 83 126 170 198 268 298 409 449

Model Number 24-2-3 24-2-4 24-2-6 24-2-8 24-2-10 24-2-12 24-2-14 24-2-16 24-2-18 24-2-202 HR Headroom 14 15-1/8 15-1/8 16-1/8 18-1/2 17-1/8 18-1/4 18-1/4 19-1/2 19-1/2

Weight 48 89 117 170 240 278 369 416 547 605Model Number 24-5-3 24-5-4 24-5-6 24-5-8 24-5-10 24-5-12 24-5-14* 24-5-16* 24-5-18* 24-5-20*

5 HR Headroom 21-1/2 21-1/2 21-1/2 22-1/2 23-1/2 27 27 28 29 30-3/8Weight 140 160 215 304 430 633 664 746 1321 1525

Model Number 24-10-3 24-10-4 24-10-6 24-10-8 24-10-10 24-10-12 24-10-14 24-10-16 24-10-18 24-10-2010 HR Headroom 25-3/4 25-3/4 28-3/4 28-3/4 31-3/4 31-3/4 31-3/4 31-3/4 34-3/4 34-3/4

Weight 210 211 432 522 759 993 1128 1257 1738 1908Model Number 24-15-3 24-15-4 24-15-6 24-15-8 24-15-10 24-15-12 24-15-14 24-15-16

15 HR Headroom 28-1/4 30-1/2 33-1/2 33-1/2 33-1/2 37 37 37Weight 252 330 502 542 882 1455 1630 1800

Model Number 24-20-3 24-20-4 24-20-6 24-20-8 24-20-10 24-20-1220 HR Headroom 31 34 37 34 37 37

Weight 315 399 735 720 1276 1251

Other D=3 D=3 D=3 D=4 D=4 D=4 D=6 D=6 D=6 D=6Dimensions (in.) E=6 E=9 E=12 E=16 E=20 E=24 E=30 E=36 E=42 E=48

A=1-1/2 T=5/8B=3 O=1C=5A=1-1/2 T=5/8B=3 O=1C=5A-1-1/2 T=3/4B=3 O=1C=5A=2 T=1B=4 O=1C=7 O=1-1/2*A=2 T=1-1/4B=4 O=1-3/4C=7A=2-1/2 T=1-1/2B=5 O=2C=9A=2-1/2 T=1-1/2B=5 O=2C=9

Strong-Bac

®Section

2014-2016 Master C

atalogT

he

Ca

ldw

ell G

rou

p• 800-628-4263 • w

ww

.caldwellinc.com

Lifting Beams

A.20

OPTION CCenter bail and extra pair ofhooks for maximum versatility.

OPTION AOff-set hook for hoistsof different capacities.

OPTION BMultiple load hooks, someoutside the bail span.

SPREADT A B

C

HRO

Model 25 - Twin Hoist Lifting Beam

See Model 21 (p. A.21) for Twin Hoist Rotating Beam

OPTION DRoller bearing hook shown (standard on30 and 40 ton models).

PRODUCT FEATURES:• Use two or more hoists to increase lifting stability.• Swivel hook with hook latch.• Several options are available for added versatility.• Complies with ASME standards.

Model Number Spread (feet)Capacity HR Headroom (in.) Other(tons) Weight (lbs.) 6 8 10 12 14 16 18 20 24 Dimensions (in.)

Model Number 25-2-6 25-2-8 25-2-10 25-2-12 25-2-14 25-2-16 25-2-18 25-2-20 25-2-242 HR Headroom 16-3/4 16-3/4 17-3/4 17-3/4 18-3/4 18-3/4 18-3/4 18-3/4 19-3/4

Weight 125 160 240 280 360 400 530 660 790Model Number 25-4-6 25-4-8 25-4-10 25-4-12 25-4-14 25-4-16 25-4-18 25-4-20 25-4-24

4 HR Headroom 20 21 22 23 23 25 25 25 26Weight 160 240 310 410 500 725 805 890 1695

Model Number 25-6-6 25-6-8 25-6-10 25-6-12 25-6-14 25-6-16 25-6-18 25-6-20 25-6-246 HR Headroom 27-1/2 28-1/2 28-1/2 30-1/2 30-1/2 30-1/2 30-1/2 30-1/2 31-1/2

Weight 220 300 380 550 640 780 1310 1450 1735Model Number 25-10-6 25-10-8 25-10-10 25-10-12 25-10-14 25-10-16 25-10-18 25-10-20 25-10-24

10 HR Headroom 29 29 32 32 32 32 32 32 33Weight 340 420 800 920 1100 1220 1705 1840 2230

Model Number 25-15-8 25-15-10 25-15-12 25-15-14 25-15-16 25-15-18 25-15-2015 HR Headroom 38-1/4 38-1/4 38-1/4 41-1/4 41-1/2 41-1/2 41-1/2

Weight 740 865 1050 1930 2158 2290 2500Model Number 25-20-8 25-20-10 25-20-12 25-20-14 25-20-16 25-20-18

20 HR Headroom 35-1/2 38-1/2 38-1/2 38-1/2 38-1/2 38-1/2Weight 830 1130 1266 1926 2196 2430

Model Number 25-30-8 25-30-10 25-30-1230 HR Headroom 54 54 54

Weight 1120 1325 1610Model Number 25-40-8 25-40-10 25-40-12

40 HR Headroom 58-1/2 58-1/2 58-1/2Weight 1165 1470 1700

SPECIFICATIONS

A=1-1/2 T=5/8B=3 O=1-1/8C=5A=1-1/2 T=5/8B=3 O=1-1/2C=5A-1-1/2 T=3/4B=3 O=2-1/16C=5A=2 T=1B=4 O=2-1/4C=7A=2 T=1-1/4B=4 O=2-1/4C=7A=2 T=1-1/4B=4 O=3C=7A=2-1/2 T=1-1/2B=5 O=3-3/4C=9A=2-1/2 T=1-1/2B=5 O=4-1/4C=9

Strong-Bac

®Section

2014-2016 Master C

atalogT

he

Ca

ldw

ell G

rou

p• 800-628-4263 • w

ww

.caldwellinc.com

A.23

Spreader Beams

PRODUCT FEATURES:• Ideal where headroom is not limited.• Adds stability to lift.• Available with standard chain or wire rope rigging.• Available with Adjust-A-Leg® rigging for off center load

adjustment (minimum lifting capacity will be approximately10-15% of beam rating).

• Wide range of additional sizes and capacities available.• Complies with ASME standards.

NOTE: Weight = Beam and hooks only - (no top rigging).

TOP RIGGING OPTIONSOPTION W

Wire rope top rigging frombeam to crane hook.

Model 30 - Fixed Spreader Beams

Model Number Spread (feet)Capacity HR Headroom (in.) Other

(tons) Weight (lbs.) 4 6 8 10 12 16 20 24 Dimensions (in.)Model Number 30-2-4 30-2-6 30-2-8 30-2-10 30-2-12 30-2-16 30-2-20 30-2-24

2 HR Headroom 34 46 58 70 82 106 132 156Weight 45 60 82 95 115 225 408 445

Model Number 30-5-4 30-5-6 30-5-8 30-5-10 30-5-12 30-5-16 30-5-20 30-5-245 HR Headroom 37 49 61 73 83 110 134 158

Weight 62 78 100 117 168 305 435 661Model Number 30-10-4 30-10-6 30-10-8 30-10-10 30-10-12 30-10-16 30-10-20 30-10-24

10 HR Headroom 41 53 64 77 86 113 138 163Weight 100 122 156 180 240 380 532 915

Model Number 30-15-4 30-15-6 30-15-8 30-15-10 30-15-12 30-15-16 30-15-20 30-15-2415 HR Headroom 43 55 65 80 92 116 140 167

Weight 126 155 185 242 270 420 665 953Model Number 30-20-4 30-20-6 30-20-8 30-20-10 30-20-12 30-20-16 30-20-20 30-20-24

20 HR Headroom 46 58 69 82 94 118 140 170Weight 170 200 233 315 350 540 775 1341

Model Number 30-30-6 30-30-8 30-30-10 30-30-12 30-30-16 30-30-2030 HR Headroom 60 70 83 95 120 145

Weight 285 402 440 530 888 1390Model Number 30-40-6 30-40-8 30-40-10 30-40-12 30-40-16

40 HR Headroom 65 77 89 102 127Weight 563 695 781 1058 1364

Specify Top Rigging

OPTION CChain top rigging frombeam to crane hook.

OPTION AAdjust-A-Leg® sling top rigging for off-center load adjustment (notincluded in QUICKSHIP Program).

Shown with Option C

SPECIFICATIONS

A=1/2 F=4-1/4B=2-1/2 O=31/32C=5A=1 F=6B=3-1/2 O=1-1/16C=7A=1-1/4 F=8-1/8B=4-3/8 O=1-1/2C=8-3/4A=1-1/2 F=9-1/4B=5-1/4 O=1-3/4C=10-1/2A=1-3/4 F=9-3/4B=6 O=2C=12A=1-3/4 F=9-3/4B=6 O=2C=12A=2 F=13B=7 O=2-3/4C=14 Strong-B

ac®

Section2014-2016 M

aster Catalog

Th

e C

ald

we

ll Gro

up

• 800-628-4263 • ww

w.caldw

ellinc.com

Coil Lifters & Upenders

A.38

Model 80H - Dixon Coil Hook with Pivoting WedgePRODUCT FEATURES:• Easy horizontal to vertical upending of coils.• Pivoting wedge for easy tilting of stacked coils.• Wedge acts as retainer.• Efficient and easy to use.• Popular for use with small, lightweight coils.• For use where overhead clearance is limited.• Specially designed heat treated pivoting wedge.• Complies with ASME standards.

EASY HORIZONTAL TO VERTICAL MOVEMENT. DO NOT USE FOR VERTICAL TO HORIZONTAL MOVEMENT.

Placing spacer blocks betweenstacked coils permits easy insertionof the wedge. Lightweight and pivoting wedge makes it easy toposition the hook.

With the hook in place, the wedgepivots as the lift is started, and thecoil begins to turn to a vertical position for transporting.

Coil is in vertical position after beinglifted from its pallet. The weight ofthe coil holds the pivoting wedge in the vertical position during transportation.

Coil being loaded on a stock reel.Hook is easily removed from thecoil after releasing the hoist.

TA

D

W

C

B

MAX.WIDTH

MAX.RADIAL

Other sizes available, consult factory.

SPECIFICATIONSDimensions (inches)

Model Capacity Max. Max. Min. WeightNumber (tons) Width Radial I.D. A B C D T W (lbs.)

80H-1/2-6/13 1/2 6 13 9 13/16 2 3-5/16 6 1/2 3-1/2 2080H-1/2-12/13 1/2 12 13 13 13/16 2 3-5/16 6 1/2 3-1/2 28

80H-1-8/16 1 8 16 10 13/16 2 3-5/16 6 1/2 3-1/2 2380H-2-10/18 2 10 18 12-1/2 1 2-5/8 4 6-3/4 3/4 2 42

80H-3.5-12/20 3-1/2 12 20 14-1/2 1-3/16 3-5/8 5-5/16 7-3/4 1 2-1/2 80

Strong-Bac

®Section

2014-2016 Master C

atalogT

he

Ca

ldw

ell G

rou

p• 800-628-4263 • w

ww

.caldwellinc.com

Coil Lifters & Upenders

A.39

Model 82 - Heavy Duty C-HookPRODUCT FEATURES:• Designed for heavy duty applications.• High tensile alloy steel plate reduces physical size and weight.• Counter balanced to hang level when empty.• Inside radius on hooks avoid coil edge contact.• Curved coil saddle is standard.• Guide handles for ease of hook positioning.• Handles a wide range of coil widths.• Available with optional padding for additional coil protection.• Complies with ASME standards.

NOTE: E = Maximum coil width ÷ 2

Dimensions (inches)

Lifting Arm Bail DimensionsModel Capacity Coil Width Length Depth Width HR Opening Thk. Weight

Number (tons) Max. Min. Throat L D W Headroom A B C T (lbs.)82-5-36 36 24 24 30 5-5/16 4 37-3/8 1-1/2 4 7 1-1/4 42082-5-48 5 48 30 24 39 6-1/8 4 38 1-1/2 4 7 1-1/4 58482-5-60 60 36 24 48 6-9/16 4 38-1/2 1-1/2 4 7 1-1/4 680

82-7 1/2-36 36 24 24 30 5-5/8 4 37-1/2 1-1/2 4 7 1-1/2 61582-7 1/2-48 7-1/2 48 30 24 39 6-5/16 4 38-1/4 1-1/2 4 7 1-1/2 77482-7 1/2-60 60 36 24 48 6-15/16 4 39 1-1/2 4 7 1-1/2 942

82-10-48 48 30 24 39 7-1/4 4 41-1/4 2 5 9 1-3/4 92882-10-60 10 60 36 24 48 7-1/2 4 41-3/8 2 5 9 1-3/4 129582-10-72 72 42 24 57 7-1/4 4 42-1/2 2 5 9 1-3/4 161682-15-48 48 30 30 39 7-1/4 4 47-7/8 2 5 9 1-3/4 145082-15-60 15 60 36 30 48 8 4 48 2 5 9 1-3/4 182482-15-72 72 42 30 57 8-3/4 4 48-3/4 2 5 9 1-3/4 222782-20-60 60 36 30 48 9-1/8 4 52-1/8 2-1/4 6 12 2 217582-20-72

2072 42 30 57 10 4 52-5/16 2-1/4 6 12 2 2625

82-25-60 60 36 34 48 9 4 57-3/4 2-1/2 6 14 2-1/4 282082-25-72

2572 42 34 57 9-3/4 4 58-1/2 2-1/2 6 14 2-1/4 3570

82-30-60 60 36 34 48 9-7/8 4 58-3/4 2-3/4 6 14 2-1/2 318082-30-72

3072 42 34 57 10-5/8 4 59-3/8 2-3/4 6 14 2-1/2 3800

82-40-72 40 72 42 38 57 11 11-3/4 68 3-1/4 7 18 3 535082-50-84 50 84 48 45 64-1/2 13 6 71-7/8 3-3/4 7 18 3 7470

Other sizes available, consult factory.

GUIDEHANDLES

W

A

C

B

SPECIFICATIONS

Center of the hoist and bail mustbe in-line with the load's center of gravity.

COIL WIDTH

THROAT

HR

T

E

L

D

Strong-Bac

®Section

2014-2016 Master C

atalogT

he

Ca

ldw

ell G

rou

p• 800-628-4263 • w

ww

.caldwellinc.com

A.37

Coil Lifters & Upenders

PRODUCT FEATURES:• Handles narrow coils with less coil edge damage.• More durable than web slings.• Lightweight for easier handling.• Built in guide handle for ease of coil positioning.• Available with optional curved coil saddle.• Inside radius on hooks avoid coil edge contact.• Complies with ASME standards.

NOTE: E = (L ÷ 2) + 1/2" inch.

THROAT

HR

E

B

L

D

TA

*Will not hang level when empty.

SPECIFICATIONS

Coil Lifting Arm Plate Bail DimensionsModel Capacity Width Length Depth HR Weight

Number (tons) Max. Throat L D Headroom A B C T (lbs.)82NC-1/2-8 1/2 8 14-1/2 8 2-1/4 18-1/2 13/16 2 3-1/4 1/2 14

82NC-1/2-12 12 14-1/2 12 2-5/8 18-1/2 13/16 2 3-1/4 1/2 1782NC-1-8 1 8 17-1/2 8 2 21-1/2 13/16 2 3-1/4 1/2 1582NC-1-16 16 17-1/2 16 2-1/2 21-1/2 13/16 2 3-1/4 1/2 2082NC-2-8 2 8 19-1/2 8 2-1/8 24-9/16 1 2-9/16 4-1/16 3/4 2282NC-2-16 16 19-1/2 16 3 24-9/16 1 2-9/16 4-1/16 3/4 40

82NC-3 1/2-12 3-1/2 12 21-1/2 12 2-7/8 28-1/8 1-3/16 3-5/8 5-5/16 1 5082NC-3 1/2-16 16 21-1/2 16 3-3/8 28-1/8 1-3/16 3-5/8 5-5/16 1 63

82NC-5-16 5 16 25-1/2 16 3-1/2 32-13/16 1-1/2 4 5-13/16 1-1/4 9482NC-5-20 20 25-1/2 20 4 32-13/16 1-1/2 4 5-13/16 1-1/4 110

Dimensions (inches)

Load center of gravity must be in-line with the center of the hoist.

Model 82NC - Narrow Coil C-Hook

Strong-Bac

®Section

2014-2016 Master C

atalogT

he

Ca

ldw

ell G

rou

p• 800-628-4263 • w

ww

.caldwellinc.com

F.51

Lifting & Spreader Beams

Model BEF - Spreader Beam End FittingsPRODUCT FEATURES:• Build your own spreader beam.• Designed to work with a range of shackle sizes, both top and bottom.• Complies with ASME standards when assembled to specifications

using A53 Grade B, schedule 40 pipe.

Shown full assembled with customer supplied rigging and bar.

The Caldwell Model BEF is designed to use A53 Grade B, schedule 40 pipe as the central structural elementbetween the end fittings. This structural material is readily available at most steel service centers. The Caldwell Model BEF-2 1/2 requires a 2-1/2" nominal size, the Model BEF-5 requires a 5" nominal size, and theBEF-8 requires an 8" nominal size A53 Grade B, schedule 40 pipe.

Other requirements are:

• The length of pipe used for this central element must be straight within 1/4" end to end.

• The pipe should have the ends cleanly cut square with its centerline.

• The A53 Grade B, schedule 40 pipe should not have any weld joint irregularities.

• Each end of the A53 Grade B, schedule 40 pipe must have the correct diameter holes drilled through both walls and both ends must be in line.

• The A53 Grade B, schedule 40 pipe used in this application does not need to pass any pressure testing.

The retaining bolts used to secure the Caldwell Model BEF 2-1/2 and 5 to the A53 Grade B, schedule 40 pipe mustbe a Grade 5 Hex Head Cap Screw 5/8-11 with minimum length of 4-1/2" and 8" respectively. The bolt for the BEF-8is a Grade 5 Hex Head Cap Screw 1-8 with a minimum length of 11-1/2".

NOTE: Complete assembly instructions are provided with each set of end fittings.

Assembly Information

Model No. Capacity (tons) Weight (lbs.)Spread (ft.) 4 5 6 8 10 12 14 15 16 18 20 22 24 26 28 30 32 34 36 Per PairBEF-2-1/2 7.5 7 6.5 5.5 4 2.9 2 1.8 - - - - - - - - - - - 16

BEF-5 17 17 17 17 17 16 15 14 13 12 10 8 7 6 5 4.5 - - - 46BEF-8 39 39 39 39 39 38 36 36 35 33 31 29 27 25 23 21 19 16 15 266

SPECIFICATIONS

NOTE: Capacity based on minimum 45° top rigging angle. Other sizes available, consult factory.

Rig-M

aster®

Section2014-2016 M

aster Catalog

Th

e C

ald

we

ll Gro

up

• 800-628-4263 • ww

w.caldw

ellinc.com