LIFTING PINSSELF-LOCKING
NEW PRODUCTS RANGE
EASY - FAST - ROBUST & SAFE ... EASY - FAST - ROBUST & SAFE ... IT DOESN’T MATTER WHAT THE CHARGEIT DOESN’T MATTER WHAT THE CHARGE
LIFTING PINS
Lifting Pins - self-locking Lifting Pins - self-locking, stainless steel
• Corrosion resistant• Temperature range up to 250 °C
• Corrosion and weather- resistant, thus also suitable for outdoor application• High-strength, precipitation- hardened• pin with an extreme load capacity• Temperature range up to 250 °C
The advantages of the HALDER self-locking lifting range :
• Shackle self-aligning in direction of force• Quick assembly through simply plugging in• Money-saving through multiple use• By using a suitable bushing, also usable in• soft and thin-walled materials
LOCATING BUSHINGS
Locating Bushings - for lifting pins Locating Bushings, plain - for lifting pins
• Used for quick and safe locating of lifting pins• Corrosion and abrasion resistant• Easily incorporated into different material• Can be mounted in blind holes• For thin-walled parts, lock nuts are used for assembly
• Used for quick and safe locating of lifting pins• This design is suitable for applications which require installation flush to the surface• Corrosion and abrasion resistant• Easily incorporated into different material• Can be mounted in blind holes• For thin-walled parts, lock nuts are used for assembly
UP TO 1000 KG
LIFTING CAPACITY
UP TO 1000 KG
LIFTING CAPACITY
Locating Bushings with Seal, plain - for lifting pins
• Used for quick and safe locating of lifting pins• The seal prevents the penetration of liquid and dirt• This design is suitable for applications which require installation ush to the surface• Corrosion and abrasion resistant• Easily incorporated into different material• Can be mounted in blind holes• For thin-walled parts, lock nuts are used for assembly
THREADED LIFTING PINS
Threaded Lifting Pins · self-locking
• Direct insert in thread• No need of additional bushings• Compared to screwing and unscrewing with a ringbolt it
saves 85% of the time• Temperature range up to 250 °C
NEW
LIFTING CAPACITY
LIFTING
2
245246
THREADED LIFTING PIN SELF-LOCKING, STEEL OR STAINLESS STEEL
REF. 245 Code=0012 245-0012
REF. 246 Code=1012 246-1012
F1, F2, F3 Carrying force for a 5-fold safety against breakage
REF 246Stainless steel 1.4542, precipitation-hard-ened
REF. 245Heat-treated steel, tempered, manganese phosphated
250° max.
Imperative : Bearing surface plated on the tool
d1 l1 d2 d3 l2 l3 l4 l5 l6 l7 l8 l9 l10 F 1[kN]
F 2[kN]
F 3[kN]
FemaleThread (g)
SteelCode REF. 245
StainlesssteelCode
REF. 246
M10 14 8,35 21,5 20 25,7 36 27 30 49 87,5 21,5 10 3,9 1,5 1,5 M10 218 0010 1010M12 17 10,07 21,5 24 25,7 36 27 30 49 87,5 21,5 12 6,2 2,5 2,3 M12 220 0012 1012M16 17 13,8 21,5 24 25,7 36 27 30 49 87,5 21,5 12 8,4 4,5 4,2 M16 223 0016 1016
LIFTING
3
247 LIFTING PIN SELF-LOCKING, STEEL
REF. 247 Code=0602 247-0602
F1, F2, F3 Carrying force for a 5-fold safety against breakage with a tolerance x between mini and max
250° max.
Heat-treated steel, tempered, manganese phosphated
d1 l 1 d2 d3 d4min. l2 l3 l4 l5 l6 l7 l8 l9 F 1
[kN]F 2[kN]
F 3[kN]
x min. mm
x max. mm
dpH11 (g) Code REF. 247
8
10 9,35 21,5 9,85 8,75 25,7 36 27 30 49 87,5 21,5 1,5 1,2 0,5 1,5 5 8 218 060115 9,35 21,5 9,85 8,75 25,7 36 27 30 49 87,5 21,5 1,5 1,2 0,5 1,5 10 8 218 060225 9,35 21,5 9,85 8,75 25,7 36 27 30 49 87,5 21,5 1,5 1,2 0,5 1,5 15 8 218 060435 9,35 21,5 9,85 8,75 25,7 36 27 30 49 87,5 21,5 1,5 1,2 0,5 1,5 15 8 218 0606
8,3
10 9,65 21,5 10,05 8,75 25,7 36 27 30 49 87,5 21,5 1,5 1,2 0,5 1,5 5 8,3 218 061115 9,65 21,5 10,05 8,75 25,7 36 27 30 49 87,5 21,5 1,5 1,2 0,5 1,5 10 8,3 219 061225 9,65 21,5 10,05 8,75 25,7 36 27 30 49 87,5 21,5 1,5 1,2 0,5 1,5 15 8,3 223 061435 9,65 21,5 10,05 8,75 25,7 36 27 30 49 87,5 21,5 1,5 1,2 0,5 1,5 15 8,3 228 0616
10
15 11,7 21,5 12,2 10,2 25,7 36 27 30 49 87,5 21,5 2,7 2,4 2,1 1,5 10 10 226 062125 11,7 21,5 12,2 10,2 25,7 36 27 30 49 87,5 21,5 2,7 2,4 2,1 1,5 10 10 238 062335 11,7 21,5 12,2 10,2 25,7 36 27 30 49 87,5 21,5 2,7 2,4 2,1 1,5 10 10 244 062550 11,7 21,5 12,2 10,2 25,7 36 27 30 49 87,5 21,5 2,7 2,4 2,1 1,5 10 10 252 0627
12
15 14,2 21,5 14,7 11 25,7 36 27 30 49 87,5 21,5 3,5 3,2 2,8 1,5 10 12 238 063125 14,2 21,5 14,7 11 25,7 36 27 30 49 87,5 21,5 3,5 3,2 2,8 1,5 15 12 243 063335 14,2 21,5 14,7 11 25,7 36 27 30 49 87,5 21,5 3,5 3,2 2,8 1,5 15 12 251 063550 14,2 21,5 14,7 11 25,7 36 27 30 49 87,5 21,5 3,5 3,2 2,8 1,5 15 12 268 0637
13,8
25 16,2 21,5 16,7 13 25,7 36 27 30 49 87,5 21,5 3,8 3,5 2,8 1,5 15 13,8 251 065150 16,2 21,5 16,7 13 25,7 36 27 30 49 87,5 21,5 3,8 3,5 2,8 1,5 35 13,8 279 065375 16,2 21,5 16,7 13 25,7 36 27 30 49 87,5 21,5 3,8 3,5 2,8 1,5 35 13,8 309 0655
16
25 18,6 25 19,2 15,1 31 44,5 27 30 49 92,8 21,5 4,8 4,5 4,1 1,5 15 16 312 064150 18,6 25 19,2 15,1 31 44,5 27 30 49 92,8 21,5 4,8 4,5 4,1 1,5 35 16 353 064375 18,6 25 19,2 15,1 31 44,5 27 30 49 92,8 21,5 4,8 4,5 4,1 1,5 40 16 388 0645
2050 24,5 30 25 19,7 36,5 52 32,6 36 56 114 26 10 8,5 6,5 1,5 25 20 607 067375 24,5 30 25 19,7 36,5 52 32,6 36 56 114 26 10 8,5 6,5 1,5 30 20 666 0675
dp H11
dp H11
245246
THREADED LIFTING PIN SELF-LOCKING, STEEL OR STAINLESS STEEL
REF. 245 Code=0012 245-0012
REF. 246 Code=1012 246-1012
F1, F2, F3 Carrying force for a 5-fold safety against breakage
REF 246Stainless steel 1.4542, precipitation-hard-ened
REF. 245Heat-treated steel, tempered, manganese phosphated
250° max.
Imperative : Bearing surface plated on the tool
d1 l1 d2 d3 l2 l3 l4 l5 l6 l7 l8 l9 l10 F 1[kN]
F 2[kN]
F 3[kN]
FemaleThread (g)
SteelCode REF. 245
StainlesssteelCode
REF. 246
M10 14 8,35 21,5 20 25,7 36 27 30 49 87,5 21,5 10 3,9 1,5 1,5 M10 218 0010 1010M12 17 10,07 21,5 24 25,7 36 27 30 49 87,5 21,5 12 6,2 2,5 2,3 M12 220 0012 1012M16 17 13,8 21,5 24 25,7 36 27 30 49 87,5 21,5 12 8,4 4,5 4,2 M16 223 0016 1016
LIFTING
4
249 LOCATING BUSHING FOR LIFTING PIN
REF. 249 Code=0936 249-0936
F1, F2, F3 Carrying force for a 5-fold safety against breakage with a tolerance x between mini and max
H11 0-0,2
+0,3 0
Stainless steel 1.4542, precipitation-hard-ened
d1 d2 For lifting pin with length l1
d3 d4 l1 l2 SWTightening
torquemax. (Nm)
x(mm)
F 1[kN]
F 2[kN]
F 3[kN] For lifting pin (g) Code REF. 249
8
M16 x 1,510 24 9,8 27,5 20 19 90 1,5 1,5 1,2 0,5 0601 / 0701 32 0900 15 24 9,8 27,5 20 19 90 1,5 1,5 1,2 0,5 0602 / 0702 33 0902
M1625 24 9,8 37,5 25 19 75 1,5 1,5 1,2 0,5 0604 / 0704 46 0904 35 24 9,8 47,5 35 19 75 1,5 1,5 1,2 0,5 0606 / 0706 55 0906
10
M20 x 1,515 28 12,2 35,5 24 24 145 1,5 2,7 2,4 2,1 0621 / 0721 70 0910 25 28 12,2 35,5 24 24 145 1,5 2,7 2,4 2,1 0623 / 0723 73 0912
M2035 28 12,2 46 29 24 130 1,5 2,7 2,4 2,1 0625 / 0725 93 0914 50 28 12,2 65 49 24 130 1,5 2,7 2,4 2,1 0627 / 0727 117 0916
12
M24 x 1,515 32 14,7 35,5 24 27 220 1,5 3,5 3,2 2,8 0631 / 0731 94 0920 25 32 14,7 36,5 24 27 220 1,5 3,5 3,2 2,8 0633 / 0733 102 0922
M2435 32 14,7 48,5 36 27 200 1,5 3,5 3,2 2,8 0635 / 0735 119 0924 50 32 14,7 72,5 60 27 200 1,5 3,5 3,2 2,8 0637 / 0737 164 0926
16
M30 x 2 25 39 19,2 44 29 30 440 1,5 4,8 4,5 4,1 0641 / 0741 163 0930
M3050 39 19,2 66 44 30 400 1,5 4,8 4,5 4,1 0643 / 0743 236 0934 75 39 19,2 96 74 30 400 1,5 4,8 4,5 4,1 0645 / 0745 323 0936
20 M36 x 2 50 43 26 70 55 36 440 1,5 10 8,5 6,5 0673 / 0773 366 0954 75 43 26 95 80 36 440 1,5 10 8,5 6,5 0675 / 0775 503 0956
248 LIFTING PIN SELF-LOCKING, STAINLESS STEEL
REF. 248 Code=0714 248-0714
F1, F2, F3 Carrying force for a 5-fold safety against breakage with a tolerance x between mini and max
250° max.
Stainless steel 1.4542, precipitation-hard-ened Stainless steel 1.4571
dp H11
dp H11
d1 l1 d2 d3 d4min. l2 l3 l4 l5 l6 l7 l8 l9 F 1
[kN]F 2[kN]
F 3[kN]
x min. mm
x max. mm
dp H11 (g) Code REF. 248
8
10 9,35 21,5 9,85 8,75 25,7 36 27 30 49 87,5 21,5 1,5 1,2 0,5 1,5 5 8 221 070115 9,35 21,5 9,85 8,75 25,7 36 27 30 49 87,5 21,5 1,5 1,2 0,5 1,5 10 8 222 070225 9,35 21,5 9,85 8,75 25,7 36 27 30 49 87,5 21,5 1,5 1,2 0,5 1,5 15 8 225 070435 9,35 21,5 9,85 8,75 25,7 36 27 30 49 87,5 21,5 1,5 1,2 0,5 1,5 15 8 229 0706
8,3
10 9,65 21,5 10,05 8,75 25,7 36 27 30 49 87,5 21,5 1,5 1,2 0,5 1,5 5 8,3 222 071115 9,65 21,5 10,05 8,75 25,7 36 27 30 49 87,5 21,5 1,5 1,2 0,5 1,5 10 8,3 223 071225 9,65 21,5 10,05 8,75 25,7 36 27 30 49 87,5 21,5 1,5 1,2 0,5 1,5 15 8,3 225 071435 9,65 21,5 10,05 8,75 25,7 36 27 30 49 87,5 21,5 1,5 1,2 0,5 1,5 15 8,3 231 0716
10
15 11,7 21,5 12,2 10,2 25,7 36 27 30 49 87,5 21,5 2,7 2,4 2,1 1,5 10 10 233 072125 11,7 21,5 12,2 10,2 25,7 36 27 30 49 87,5 21,5 2,7 2,4 2,1 1,5 10 10 243 072335 11,7 21,5 12,2 10,2 25,7 36 27 30 49 87,5 21,5 2,7 2,4 2,1 1,5 10 10 250 072550 11,7 21,5 12,2 10,2 25,7 36 27 30 49 87,5 21,5 2,7 2,4 2,1 1,5 10 10 257 0727
12
15 14,2 21,5 14,7 11 25,7 36 27 30 49 87,5 21,5 3,5 3,2 2,8 1,5 10 12 246 073125 14,2 21,5 14,7 11 25,7 36 27 30 49 87,5 21,5 3,5 3,2 2,8 1,5 15 12 255 073335 14,2 21,5 14,7 11 25,7 36 27 30 49 87,5 21,5 3,5 3,2 2,8 1,5 15 12 265 073550 14,2 21,5 14,7 11 25,7 36 27 30 49 87,5 21,5 3,5 3,2 2,8 1,5 15 12 273 0737
13,8
25 16,2 21,5 16,7 13 25,7 36 27 30 49 87,5 21,5 3,8 3,5 2,8 1,5 15 13,8 255 075150 16,2 21,5 16,7 13 25,7 36 27 30 49 87,5 21,5 3,8 3,5 2,8 1,5 35 13,8 283 075375 16,2 21,5 16,7 13 25,7 36 27 30 49 87,5 21,5 3,8 3,5 2,8 1,5 35 13,8 311 0755
16
25 18,6 25 19,2 15,1 31 44,5 27 30 49 92,8 21,5 4,8 4,5 4,1 1,5 15 16 313 074150 18,6 25 19,2 15,1 31 44,5 27 30 49 92,8 21,5 4,8 4,5 4,1 1,5 35 16 367 074375 18,6 25 19,2 15,1 31 44,5 27 30 49 92,8 21,5 4,8 4,5 4,1 1,5 40 16 403 0745
2050 24,5 30 25 19,7 36,5 52 32,6 36 56 114 26 10 8,5 6,5 1,5 25 20 607 077375 24,5 30 25 19,7 36,5 52 32,6 36 56 114 26 10 8,5 6,5 1,5 30 20 666 0775
LIFTING
5
249 LOCATING BUSHING FOR LIFTING PIN
REF. 249 Code=0936 249-0936
F1, F2, F3 Carrying force for a 5-fold safety against breakage with a tolerance x between mini and max
H11 0-0,2
+0,3 0
Stainless steel 1.4542, precipitation-hard-ened
d1 d2 For lifting pin with length l1
d3 d4 l1 l2 SWTightening
torquemax. (Nm)
x(mm)
F 1[kN]
F 2[kN]
F 3[kN] For lifting pin (g) Code REF. 249
8
M16 x 1,510 24 9,8 27,5 20 19 90 1,5 1,5 1,2 0,5 0601 / 0701 32 0900 15 24 9,8 27,5 20 19 90 1,5 1,5 1,2 0,5 0602 / 0702 33 0902
M1625 24 9,8 37,5 25 19 75 1,5 1,5 1,2 0,5 0604 / 0704 46 0904 35 24 9,8 47,5 35 19 75 1,5 1,5 1,2 0,5 0606 / 0706 55 0906
10
M20 x 1,515 28 12,2 35,5 24 24 145 1,5 2,7 2,4 2,1 0621 / 0721 70 0910 25 28 12,2 35,5 24 24 145 1,5 2,7 2,4 2,1 0623 / 0723 73 0912
M2035 28 12,2 46 29 24 130 1,5 2,7 2,4 2,1 0625 / 0725 93 0914 50 28 12,2 65 49 24 130 1,5 2,7 2,4 2,1 0627 / 0727 117 0916
12
M24 x 1,515 32 14,7 35,5 24 27 220 1,5 3,5 3,2 2,8 0631 / 0731 94 0920 25 32 14,7 36,5 24 27 220 1,5 3,5 3,2 2,8 0633 / 0733 102 0922
M2435 32 14,7 48,5 36 27 200 1,5 3,5 3,2 2,8 0635 / 0735 119 0924 50 32 14,7 72,5 60 27 200 1,5 3,5 3,2 2,8 0637 / 0737 164 0926
16
M30 x 2 25 39 19,2 44 29 30 440 1,5 4,8 4,5 4,1 0641 / 0741 163 0930
M3050 39 19,2 66 44 30 400 1,5 4,8 4,5 4,1 0643 / 0743 236 0934 75 39 19,2 96 74 30 400 1,5 4,8 4,5 4,1 0645 / 0745 323 0936
20 M36 x 2 50 43 26 70 55 36 440 1,5 10 8,5 6,5 0673 / 0773 366 0954 75 43 26 95 80 36 440 1,5 10 8,5 6,5 0675 / 0775 503 0956
LIFTING
6
250 LOCATING BUSHING, PLAIN, FOR LIFTING PIN
REF. 250 Code=1956 250-1956
F1, F2, F3 Carrying force for a 5-fold safety against breakage with a tolerance x between mini and max
M16/M16x1,5/M20M20x1,5/M24x1,5/M30x2 M24/M30/M36x2
Stainless steel 1.4542, precipitation-hard-ened 0-0,2
+0,3 0
+0,1 0
+0,1 0
H11H11
+0,1 0
+0,3 0
0-0,2
+0,1 0
d1 d2 For lifting pin with length l1
d3 d4 d5 l1 l2 l3 l4Tightening
torquemax. (Nm)
x(mm)
F 1[kN]
F 2[kN]
F 3[kN] For lifting pin (g) Code REF. 250
8
M16 x 1,510 24 9,8 3,1 25 20 16 – 75 1,5 1,5 1,2 0,5 0601 / 0701 33 1900 15 24 9,8 3,1 25 20 16 – 75 1,5 1,5 1,2 0,5 0602 / 0702 33 1902
M1625 24 9,8 3,1 35 30 16 – 75 1,5 1,5 1,2 0,5 0604 / 0704 33 190435 24 9,8 3,1 45 40 16 – 75 1,5 1,5 1,2 0,5 0606 / 0706 33 1906
10
M20 x 1,515 28 12,2 5,1 30 24 20 – 100 1,5 2,7 2,4 2,1 0621 / 0721 70 191025 28 12,2 5,1 35 29 20 – 100 1,5 2,7 2,4 2,1 0623 / 0723 70 1912
M2035 28 12,2 5,1 45 39 20 – 100 1,5 2,7 2,4 2,1 0625 / 0725 70 191450 28 12,2 5,1 60 54 20 – 100 1,5 2,7 2,4 2,1 0627 / 0727 70 1916
12
M24 x 1,515 32 14,7 5,1 32 26 22 – 150 1,5 3,5 3,2 2,8 0631 / 0731 94 192025 32 14,7 5,1 40 34 22 – 150 1,5 3,5 3,2 2,8 0633 / 0733 94 1922
M2435 32 14,7 5,1 50 44 22 3,8 150 1,5 3,5 3,2 2,8 0635 / 0735 94 192450 32 14,7 5,1 65 59 22 18,8 150 1,5 3,5 3,2 2,8 0637 / 0737 94 1926
16
M30 x 2 25 39 19,2 5,1 45 39 30 – 200 1,5 4,8 4,5 4,1 0641 / 0741 163 1930
M3050 39 19,2 5,1 65 59 30 6 200 1,5 4,8 4,5 4,1 0643 / 0743 163 193475 39 19,2 5,1 90 84 30 31 200 1,5 4,8 4,5 4,1 0645 / 0745 163 1936
20 M36 x 2 50 43 26 5,1 70 63 30 3,5 200 1,5 10 8,5 6,5 0673 / 0773 340 195475 43 26 5,1 95 88 30 28,5 200 1,5 10 8,5 6,5 0675 / 0775 340 1956
LIFTING
7
251 LOCATING BUSHING WITH SEAL, PLAIN, FOR LIFTING PIN
REF. 251 Code=1962 251-1962
F1, F2, F3 Carrying force for a 5-fold safety against breakage with a tolerance x between mini and max
Stainless steel 1.4542, precipitation-hard-ened
0-0,2
+0,3 0
+0,1 0
H11
d1 d2 For lifting pin with length l1
d3 d4 d5 l1 l2 l3 l4Tightening
torquemax. (Nm)
x(mm)
F 1[kN]
F 2[kN]
F 3[kN] For lifting pin (g) Code REF. 251
8 M16 x 1,5 10 24 9,9 3,1 37,5 32,5 16 12,5 75 1,5 1,5 1,2 0,5 0601 / 0701 40 1960 10 M20 x 1,5 15 28 12,3 5,1 51 45 20 21 100 1,5 2,7 2,4 2,1 0621 / 0721 82 1961 12 M24 x 1,5 15 32 14,4 5,1 53 47 22 21 150 1,5 3,5 0,2 2,8 0631 / 0731 125 1962 16 M30 x 2 25 39 19,3 5,1 78 72 30 33 200 1,5 4,8 4,5 4,1 0641 / 0741 253 1963
250 LOCATING BUSHING, PLAIN, FOR LIFTING PIN
REF. 250 Code=1956 250-1956
F1, F2, F3 Carrying force for a 5-fold safety against breakage with a tolerance x between mini and max
M16/M16x1,5/M20M20x1,5/M24x1,5/M30x2 M24/M30/M36x2
Stainless steel 1.4542, precipitation-hard-ened 0-0,2
+0,3 0
+0,1 0
+0,1 0
H11H11
+0,1 0
+0,3 0
0-0,2
+0,1 0
d1 d2 For lifting pin with length l1
d3 d4 d5 l1 l2 l3 l4Tightening
torquemax. (Nm)
x(mm)
F 1[kN]
F 2[kN]
F 3[kN] For lifting pin (g) Code REF. 250
8
M16 x 1,510 24 9,8 3,1 25 20 16 – 75 1,5 1,5 1,2 0,5 0601 / 0701 33 1900 15 24 9,8 3,1 25 20 16 – 75 1,5 1,5 1,2 0,5 0602 / 0702 33 1902
M1625 24 9,8 3,1 35 30 16 – 75 1,5 1,5 1,2 0,5 0604 / 0704 33 190435 24 9,8 3,1 45 40 16 – 75 1,5 1,5 1,2 0,5 0606 / 0706 33 1906
10
M20 x 1,515 28 12,2 5,1 30 24 20 – 100 1,5 2,7 2,4 2,1 0621 / 0721 70 191025 28 12,2 5,1 35 29 20 – 100 1,5 2,7 2,4 2,1 0623 / 0723 70 1912
M2035 28 12,2 5,1 45 39 20 – 100 1,5 2,7 2,4 2,1 0625 / 0725 70 191450 28 12,2 5,1 60 54 20 – 100 1,5 2,7 2,4 2,1 0627 / 0727 70 1916
12
M24 x 1,515 32 14,7 5,1 32 26 22 – 150 1,5 3,5 3,2 2,8 0631 / 0731 94 192025 32 14,7 5,1 40 34 22 – 150 1,5 3,5 3,2 2,8 0633 / 0733 94 1922
M2435 32 14,7 5,1 50 44 22 3,8 150 1,5 3,5 3,2 2,8 0635 / 0735 94 192450 32 14,7 5,1 65 59 22 18,8 150 1,5 3,5 3,2 2,8 0637 / 0737 94 1926
16
M30 x 2 25 39 19,2 5,1 45 39 30 – 200 1,5 4,8 4,5 4,1 0641 / 0741 163 1930
M3050 39 19,2 5,1 65 59 30 6 200 1,5 4,8 4,5 4,1 0643 / 0743 163 193475 39 19,2 5,1 90 84 30 31 200 1,5 4,8 4,5 4,1 0645 / 0745 163 1936
20 M36 x 2 50 43 26 5,1 70 63 30 3,5 200 1,5 10 8,5 6,5 0673 / 0773 340 195475 43 26 5,1 95 88 30 28,5 200 1,5 10 8,5 6,5 0675 / 0775 340 1956
LIFTING
8
252 ADJUSTABLE FACE WRENCH, OFFSET
REF. 252 Code=1990 252-1990
Suitable for size d1 Pin diameter (-0,1) (g) Code REF. 252
8 / 10 / 12 3 121 199016 / 20 / 25 5 309 1991
253 FACE WRENCH (SOCKET WRENCH INSERT)
REF. 253 Code=1996 253-1996
Suitable for size d1 Pin spacing (±0,1) Pin diameter (-0,1) Square drive(inch) (g) Code REF. 253
8 16 3 1/2 116 199510 20 5 1/2 136 199612 22 5 1/2 185 1997
16 / 20 30 5 1/2 243 1998
LIFTING
9
EXAMPLE OF APPLICATION 252 ADJUSTABLE FACE WRENCH, OFFSET
REF. 252 Code=1990 252-1990
Suitable for size d1 Pin diameter (-0,1) (g) Code REF. 252
8 / 10 / 12 3 121 199016 / 20 / 25 5 309 1991
253 FACE WRENCH (SOCKET WRENCH INSERT)
REF. 253 Code=1996 253-1996
Suitable for size d1 Pin spacing (±0,1) Pin diameter (-0,1) Square drive(inch) (g) Code REF. 253
8 16 3 1/2 116 199510 20 5 1/2 136 199612 22 5 1/2 185 1997
16 / 20 30 5 1/2 243 1998
RABOURDIN SASParc Gustave Eiffel
4, avenue Gutenberg77600 BUSSY SAINT GEORGES
+33(0)1 64 76 41 01+33(0)1 64 76 41 06
www.rabourdin.frwww.eshop.rabourdin.fr