Linea Handless Range units

MANHATTAN SPECIFIER’S GUIDE2

BEFORE PLANNING YOUR HANDLE-LESS KITCHEN

PLEASE CONSIDER THE ITEMS LISTED BELOW

BASE UNITS

1: ALL BASE & TALL UNITS WITH EXPOSED END PANELS WILL NEED TO BE COVERED WITH DECOR PANEL , NO PLINTH RETURNS TO BE SPECIFIED,

ALWAYS USE DECOR PANELS. THE DECOR PANELS WILL BE USED TO COVER THE ENDS OF THE ALUMINIUM TRIMS.

2: DRAWER PACKS ARE ONLY AVAILABLE IN 500, 600, 800 & 1000mm WIDE, USING TWO 140mm & ONE 355mm HIGH DRAWERS.

‘DO NOT SPECIFY 300mm OR 400mm WIDE DRAWER PACKS AS THE DRAWER FRONTS ARE NOT AVAILABLE’ IN THESE SIZES.

3: NEW WORKTOP HEIGHT FOR HANDLE-LESS KITCHENS, THIS WILL BE SET AT 942mm, FROM THE FLOOR TO THE TOP EDGE OF THE WORKTOP.

4: ALL BASE UNIT DECOR PANELS, INFILL PANELS & FLY END PANELS WILL BE HIGHER TO SUIT THE NEW HEIGHT WORKTOP.

5: BASE OVEN HOUSING UNIT 4615 THAT USES A STANDARD SIZE SINGLE OVEN WILL HAVE TWO SMALL OVEN INFILL PANELS,

ONE PANEL FITTED ABOVE THE OVEN & ONE PANEL FITTED BELOW THE OVEN.

6: NEW FITTING POSITION FOR THE S’FRAME FRONT STRIP, POSITIONED FORWARD FLUSH WITH THE ADJACENT DOOR.

TALL UNIT

1: TALL UNIT HEIGHT TO SUIT 720mm WALL UNITS = 1970mm WITH PLINTH 2120mm.

2: TALL UNIT HEIGHT TO SUIT 900mm WALL UNITS = 2150mm WITH PLINTH 2300mm.

3: EXPOSED ENDS & END OF RUN TALL UNITS ‘DO NOT USE PLINTH RETURNS’ ALWAYS USE DECOR PANELS.

THE DECOR PANELS WILL BE USED TO COVER THE ENDS OF THE ALUMINIUM TRIMS.

4: THE FRIDGE FREEZER HOUSING UNIT MUST BE SPECIFIED WITH VERTICAL ALUMINIUM TRIM TO ALLOW FOR ACCESS TO THE DOOR HANDLES PLEASE

SEE PAGE 11

5: PLEASE SEE PAGE 10 FOR FULL DETAILS ON ALL TALL HOUSING UNITS

6: PLEASE NOTE: SHORT BASE UNIT DOORS WILL NO LONGER BE AVAILABLE FOR TALL HOUSING UNITS OR BASE UNITS

7: TO ALLOW FOR THE TOP DOORS OF THE OVEN HOUSING UNITS TO OPEN THE UNITS WILL BE FITTED WITH PUSH-FIT HINGES AND CATCHES.

WALL UNITS

1: ALL WALL UNITS HAVE TWO BOTTOM PANELS TO ALLOW FOR A FINGER RECESS TO OPEN THE DOORS.

2: THE NEW BOTTOM PANEL WILL BE AVAILABLE IN TWO OPTIONS.

OPTION ONE: MADE WITH RECESSED LIGHTING WITH CHANNELS FOR CONCEALING THE LIGHTING WIRES

OPTION TWO: MADE WITH OUT THE CHANNELS FOR CONCEALING THE LIGHTING WIRES

BaseUnit

575WallUnit

900WallUnit

360WallUnit

22

86

.00

15

61

.00

HousingUnit &BroomUnits

360WallUnit

StainlessSteel Hood

BaseUnit

BaseUnit

BaseUnit

BaseUnit

22

86

.00

18

46

.00

16

54

.00

16

19

.00

14

70

.00

91

8.0

0N

EW

HE

IGH

T 8

39

.00

BaseUnit

44

0.0

0

720WallUnit

MANHATTAN SPECIFIER’S GUIDE 3

SIDE ELEVATION

WALL NOGGINS TO SUIT MANHATTAN’S RANGE OF KITCHEN UNITS. NOTE: WALL UNIT NOGGINS SHOULD BE A MINIMUM OF 440mm HIGH.

WALL UNITS SHOWINGFINGER PULL

BASE UNITS DETAIL SHOWING THE HANDLESS TRIMS forLONG DOOR UNITS AND DRAWER PACK UNITS

HOUSING UNITS SHOWING THE HANDLESS TRIMS

DETAILS SHOWING THE END ELEVATION OF HANDLE-LESS KITCHEN UNITS & HANDLE TRIM CONFIGURATIONS

458mm

2120mm

BASE UNIT SHOWING THE WORKTOP TRIM

WORKTOP

TRIM

DRAWER / DOOR

TRIMMicrowave

Single oven

Single oven

Drawer pack

Panel

Panel

Panel

Panel

Long door

Top hung door

opening with push

catches

Top hung door

opening with push

catches

DRAWER PACKSHOWINGDRAWER TRIM

UNDER WORKTOP APPLIANCE SPACE HEIGHTS

The space required for appliances that fit under worktops.

With Handle-less kitchens the aluminium trim will runacross the top of the appliance space,this will restrict the height for a number of appliances.

The maximum height for appliances will be 847mm fromthe floor to the under side of the aluminium trim with theplinth set at 150mm high.

Where appliances need a top fixing, a panel will need to bespecified to allow for the fixing.This will change the maximum height for the appliancespace to 831mm. The panel can be made from plinthmaterial or can be specified as a 9036 panel size = 600mmx 200.8mm made from 16mm MFC with edging to the longedges

815mm TO 847mm 815mm TO 831mm

Top fixing panel

BASE BOTTLE STORAGE UNIT

With full-height, pull-out door Door height 715mm

NOTE: IDEALLY TO BE FITTED EITHER SIDE OF A HOB OR BASE OVEN HOUSING UNIT.NOTE: 2700 UNIT - ONLY AVAILABLE WITH A STAINLESS STEEL DOOR.NOTE: 2719 UNIT - THE STYLE OF THE DOOR WILL DIFFER ACCORDING TO THE RANGE.

WIDTH 568 DEEP

DOOR TO 150 2142

MATCH RANGE

MANHATTAN SPECIFIER’S GUIDE4 MANHATTAN SPECIFIER’S GUIDE4

WIDTH 568 DEEP

600 Lt Hd 2091

(min 336–378) Rt Hd 2092

800 Lt Hd 2093

(min 236–278) Rt Hd 2094

1000 Lt Hd 2095

(min 136–178) Rt Hd 2096

1200 Lt Hd 2097

(min 36–78) Rt Hd 2098

**800 Lt Hd 2099

(min 286–328) Rt Hd 2100

*800 Lt Hd 2101

(min 336–378) Rt Hd 2102

*1000 Lt Hd 2103

(min 236–278) Rt Hd 2104

*1200 Lt Hd 2105

(min 236–278) Rt Hd 2106

BASE UNITS

With full-height door Door height 715mm

With full-height doors Door height 715mm

WIDTH 568 DEEP

300 Lt Hd 2077

Rt Hd 2078

400 Lt Hd 2079

Rt Hd 2080

450 Lt Hd 2081

Rt Hd 2082

500 Lt Hd 2083

Rt Hd 2084

600 Lt Hd 2085

Rt Hd 2086

800 2087

900 2088

1000 2089

1200 2090

BASE CORNER UNIT

With full-height door

600mm WIDE UNIT 800mm WIDE UNIT 1000mm WIDE UNIT 1200mm WIDE UNIT

(300mm Wide door) (400mm Wide door) (500mm Wide door) (600mm Wide door)

**800mm WIDE UNIT *800mm WIDE UNIT *1000mm WIDE UNIT *1200mm WIDE UNIT

(450mm Wide door) (500mm Wide door) (600mm Wide door) (2 X 400mm Wide doors)

NOTE: MIN & MAX POSITIONS FROM THE WALL WITH THE FRONT STRIP SET IN THE VERTICAL POSITION RESULTING IN636MM FROM THE OPPOSING WALL.

BASE UNIT S’FRAME

PLEASE NOTE:

1: THE TOP EDGE OF THE S’FRAME MID STRIP WILL HAVE

TO BE NOTCHED ON SITE BY THE FITTER AFTER FINAL

ADJUSTMENT OF THE S’FRAME. THIS MODIFICATION IS

TO ALLOW FOR THE ALUMINIUM TRIM TO RUN BEHIND

THE S’FRAME.

2: THE S’FRAME FRONT STRIP TO BE POSITIONED FLUSH

WITH FRONT FACE OF THE ADJACENT DOOR, THIS

MODIFICATION IS TO ALLOW FOR THE ALUMINIUM TRIM

TO RUN BEHIND THE S’FRAME.

MID STRIP

FRONT STRIP

NOTCH

MANHATTAN SPECIFIER’S GUIDE 5MANHATTAN SPECIFIER’S GUIDE 5

WIDTH 316 DEEP

WIDTH 568 DEEP

500 Lt Hd 2107

Rt Hd 2108

600 Lt Hd 2109

Rt Hd 2110

800 2111

900 2112

1000 2113

1200 2114

BASE SINK UNITS

With full-height door Door height 715mm

With full-height doors Door height 715mm

WIDTH 568 DEEP

WIDTH 568 DEEP

800 Lt Hd 2115

(min 236–278) Rt Hd 2116

**800 Lt Hd 2117

(min 286–328) Rt Hd 2118

1000 Lt Hd 2119

(min 136–178) Rt Hd 2120

1200 Lt Hd 2121

(min 36–78) Rt Hd 2122

*800 Lt Hd 2125

(min 336–378) Rt Hd 2126

*1000 Lt Hd 2127

(min 236–278) Rt Hd 2128

*1200 Lt Hd 2129

(min 236–278) Rt Hd 2130

BASE SINK CORNER UNITS


800mm WIDE UNIT **800mm WIDE UNIT 1000mm WIDE UNIT 1200mm WIDE UNIT

(400mm Wide door) (450mm Wide door) (500mm Wide door) (600mm Wide door)

*800mm WIDE UNIT *1000mm WIDE UNIT *1200mm WIDE UNIT

(500mm Wide door) (600mm Wide door) (2 X 400mm Wide door)


WIDTH 568 DEEP

500 6705

600 6706

800 6708

900 6709

1000 6710

1200 6712

BASE SINK BACK PANELS

Optional extra Height 430mm

WIDTH CODE

500 FACM355A

600 FACM349A

800 FACM350A

900 FACM356A

1000 FACM351A

1200 FACM357A

SINK BOTTOM LINERS

Optional extra


KITCHEN ACCESSORY - HALF CIRCLE, FULL EXTENSION CAROUSELS

Carousels for use in corner units

NOTE: CAROUSEL TRAYS SUPPLIED AS A SINGLE ITEM, IT IS RECOMMENDED THAT YOU SUPPLY TWO CAROUSELS PER BASE CORNER UNIT.NOTE: CAROUSEL TRAYS WILL ONLY SUIT 1000MM BASE CORNER UNITS, WITH A DOOR SIZE OF 500MM.

SIZE CODE

000 X 000 MECH100A

CORNER BASE UNIT WITH LE MANS STORAGE MECHANISM

The Le Mans storage shelves move completely out of the unit for easy access to both shelves

WIDTH CODE

1000 Lt Hd 2135

(min 136-178) Rt Hd 2136

BASE DISPLAY PENINSULAR BACK PANEL FIXING KIT

NOTE: TO BE SPECIFIED IN CONJUNCTION WITH A BASE PENINSULAR BACK PANEL (SEE ABOVE).

CODE

6012

BASE FLY END PANELS

Without notch NEW HEIGHT 934mm

WIDTH DEPTH CODE

16 591 6328

668 6329

HEIGHT WIDTH CODE

VARIABLE VARIABLE 9036

BASE DISPLAY PENINSULAR BACK PANELS

[[[

NOTE: PENINSULAR BACK PANELS SHOULD BE SPECIFIED EITHER 751MM OR 934MM HIGH TO SUIT ADJACENT UNITS. REMEMBER TO SPECIFYHEIGHT, LENGTH AND GRAIN DIRECTION WHEN ORDERING.NOTE: WHEN USED IN CONJUNCTION WITH BASE DISPLAY PENINSULAR UNITS, A BACK PANEL FIXING KIT 6012 MUST BE SPECIFIED (SEEBELOW).

PENINSULAR

PANEL

934mm HIGH

6012 PLINTH

PENINSULAR

PANEL

898mm HIGH

PENINSULAR

PANEL

751mm HIGH

WIDTH 568 DEEP

1000 Lt Hd 2131

(min 136-178) Rt Hd 2132

*1000 Lt Hd 2133

(min 236-278) Rt Hd 2134

1000mm WIDE UNIT

(500mm Wide door)

*1000mm WIDE UNIT

(600mm Wide door)

BASE CORNER UNITS - WITH PULL-OUT ‘MAGIC CORNER’ MECHANISM

With full-height door Carcase height 720mm

Door height 715mm


PENINSULAR

PANEL

715mm HIGH

6012 PLINTH

ALUMINIUMTRIM

ALUMINIUMTRIM


WIDTH 568 DEEP

500 2137

600 2138

BASE DRAWER UNITS WITH ‘METAL-SIDED’ THREE-QUARTER OPENING DRAWERS

Three drawer unit - comprising two top drawer and one high-sided drawer

450mm deep drawer box, finished in white

2 X Drawer front, height 140mm

1 X Deep drawer fronts, height 355mm

CODE

HINGE064A

CODE

MECH126A

WIDTH 568 DEEP

800 2139

1000 2140

BASE DRAWER UNITS WITH TWIN-WALLED, FULL EXTENSION, SOFT CLOSING DRAWERS

Three drawer unit

450mm deep drawer box, finished in grey

2 X Drawer front, height 140mm

1 X Pan drawer fronts, height 355mm

BASE OVEN HOUSING UNITS

To suit an integrated oven

Aperture height 600mm

Two infill panels height = 58mm each

NOTE: TOP RAIL TO BE REMOVED ON SITE.

WIDTH 568 DEEP

600 2141

SOFT CLOSING DOORS - UPGRADE OPTION

Available with to suit all base, wall, highboard and tall units as an optional upgrade

NOTE: THE CODE HING064A = ALL THE DOORS IN ONE KITCHEN, MARK THE QUANTITY OF DOORS IN THE KITCHEN NEXT TO THE CODE HING064A

NOTE: NOT SUITABLE FOR BI-FOLD WALL UNITS

DRAWER UNITS WITH TWIN-WALLED, FULL EXTENSION, SOFT CLOSING DRAWERS - UPGRADE OPTION

Available as up upgrade option to all base and tall units

NOTE: THE CODE MECH126A = ALL THE DOORS IN ONE KITCHEN, MARK THE QUANTITY OF DOORS IN THE KITCHEN NEXT TO THE CODEMECH126A

NOTE: NOT SUITABLE FOR BI-FOLD WALL UNITS RAWER UNITS WITH TWIN-WALLED, FULL EXTENSION, SOFT CLOSINGDRAWERS - UPGRADE OPTION

ENTRY LEVEL DRAWER UNITS WITH SINGLE-WALLED, SOFT CLOSING DRAWERS - UPGRADE OPTION

Available as up upgrade option to all base and tall units

NOTE: THE CODE MECH000A = ALL THE DRAWERS IN ONE KITCHEN, MARK THE QUANTITY OF DRAWERS IN THE KITCHEN NEXT TO THE CODEMECH000A

CODE

SDRAWER10

BASE UNIT INTEGRATED APPLIANCE CONVERSION KIT

NOTE: USED TO CONVERT A FREE-STANDING APPLIANCE SPACE OF 620MM TO AN INTEGRATED SPACE OF 600MM.NOTE: STANDARD ‘S’ FRAME FRONT STRIP OF 50MM IS REPLACED WITH THIS SPECIAL FRONT STRIP OF 70MM ON SITE.

HEIGHT WIDTH CODE

720 70 6019

MANHATTAN SPECIFIER’S GUIDEMANHATTAN SPECIFIER’S GUIDE8

BASE TRAY SPACE

NOTE: SUPPLIED 300MM WIDE, TO BE CUT DOWN ON-SITE TO REQUIRED WIDTH.NOTE: MINIMUM WIDTH IS 100MM.

BASE UNIT INFILL PANELS

New Panel height 715mm

NOTE: TO BE ASSEMBLED AND CUT DOWN ON-SITE TO SUIT THE REQUIRED WIDTH.NOTE: MINIMUM WIDTH IS 16MM.

WIDTH 568 DEEP

300 6001

WIDTH 715 HIGH

150 8001

300 8002

400 8003

PLEASE NOTE:

THE INFILL TO BE POSITIONED FLUSH

WITH FRONT FACE OF THE ADJACENT

DOOR, THIS MODIFICATION IS TO ALLOW

FOR THE ALUMINIUM TRIM TO RUN

BEHIND THE INFILL PANEL.

ALUMINIUM TRIM

SIZE CODE

TRIM 56mm High 6362

ONE PAIR OF FIXING CLIPS FITT 111A

WORKTOP ALUMINIUM TRIM & FIXING KIT

‘A’ POSITION THE BLACK PLASTIC TRIM HOUSING INTO THE END CUT OUT OF ALL FOUR END PANELS.‘B’ POSITION AND SLIDE THE FOUR SMALL BLACK PLASTIC TRIM RUNNERS ONTO THE ALUMINIUM TRIM.‘C’ PUSH/HAMMER THE FOUR SMALL TRIM RUNNERS ONTO THE TRIM HOUSING, WHEN THE FITTING ARE LOCATED TOGETHER SCREW THE TRIMHOUSINGS TO THE END PANELS

DETAIL ’A’ DETAIL ’C’DETAIL ’B’DETAIL SHOWING THEALUMINIUM TRIM AND PLASTIC FIXINGS

FIXING DETAILS FOR THE ALUMINIUM FINGER TRIM

WORKTOP TRIM

THE QUANTITY AND LENGTH MUST BE SPECIFIED

THE PRICE FOR THE ALUMINIUM TRIM = PRICE PER LINEAR METER

THE MAX LENGTH OF THE TRIM = 3M

FIXING CLIPS

THE QUANTITY OF FIXING CLIPS MUST BE SPECIFIED

ALLOW ONE PAIR OF FIXING CLIPS PER UNIT


WIDTH 2120 HIGH 2300 HIGH

300 Lt Hd 3451 Lt Hd 3459

Rt Hd 3452 Rt Hd 3460

400 Lt Hd 3453 Lt Hd 3461

Rt Hd 3454 Rt Hd 3462

500 Lt Hd 3455 Lt Hd 3463

Rt Hd 3456 Rt Hd 3464

600 Lt Hd 3457 Lt Hd 3465

Rt Hd 3458 Rt Hd 3466

2120 high 2300 high

TALL LARDER UNITS

Unit height 2120mm

Carcase height 1970mm

Top door height 1245mm

Bottom door height 715mm

One fixed shelf

Two loose shelves

For more shelves please see

page 16

Unit height 2300mm




One fixed shelf

Two loose shelves

For more shelves please see

page 16

EXTRA DEEP BASE UNIT END PANELS - TO SUIT UNITS USING 650mm DEEP WORKTOPS CODE

Lt & Rt Hd 6337

The base unit will be fitted with Two

extra deep end panels per unit

2120mm 2300mm

EXTRA DEEP TALL UNIT END PANELS - TO SUIT UNITS USING 650mm DEEP WORKTOPS HEIGHT CODE

1970 6335

2300 6336

How to order the extra deep end panels:

1: Order the base or tall unit that needs an extra deep end as astandard unit code. Then add SJC A5666 so the extra deep end canbe added to the correct unit on the order

2: Order the extra deep end panel to suit that unit, using the newcodes. Then add SJC A5666 so the extra deep end can be added tothe order.

3: The extra deep end panel will then be fitted to the required unitin the factory

TALL UNIT INFILL PANELS

NOTE: TO BE ASSEMBLED AND CUT DOWN ON-SITE TO SUIT THE REQUIRED WIDTH.NOTE: MINIMUM WIDTH IS 16MM.NOTE: 1970MM HIGH INFILL PANEL TO BE USED WITH 2120MM HIGH TALL UNITS.NOTE: 2150MM HIGH INFILL PANEL TO BE USED WITH 2300MM HIGH TALL UNITS.


150 8032 8031

300 8016 8014

400 8092 8093

TALL UNIT SHELVES

NOTE: SHELVES MANUFACTURED FROM 16MM MELAMINE FACED CHIPBOARD, LIPPED WITH 0.6MM PVC EDGING. COLOUR DECIDED BY RANGECHOICES.NOTE: SUPPLIED AS A PAIR WITH SHELF CLIPS.NOTE: SHELF WIDTH ANNOTATED IS NOMINAL TO SUIT UNITS.

WIDTH CODE

300 6027

400 6024

500 6028

600 6029

NOTE: LARDERS & BROOM UNITS MUST BE SPECIFIED WITH VERTICAL ALUMINIUM STRIP TO ALLOW ACCESS THE THE DOOR HANDLES PLEASE SEE PAGE 11

FOR DETAILS

The tall unit will be fitted with Two

extra deep end panels per unit


DEPTH WIDTH 2120 HIGH 2300 HIGH

568 600 Lt Hd 4601 Lt Hd 4607

Rt Hd 4602 Rt Hd 4608

568 600 4603 4611

568 600 4600 Lt Hd 4609

Rt Hd 4610

568 600 4604 4612

2120high 2300 high

2120 high 2300 high

2120 high 2300 high

2120 high 2300 high

SPECIFICATION OF APPLIANCES TO SUIT A HOUSING UNIT

Manhattan can supply both highboard and tall housing units to accommodate a wide selection of built in ovens, refrigerators, freezers, microwaves and combinations.

The appliance manufacturer and model must be specified when ordering to enable us to prepare exact sizes and if necessary, detail special units to suit individual

requirements.

Where the appliance height is less than the aperture size, an infill panel is fitted.

All appliances must be fitted strictly in accordance with the manufacturer’s instructions.

Please check the manufacturer’s appliance instructions with regard to specific ventilation requirements: it may be necessary to notch the plinth locally.

TALL HOUSING UNITS with UPGRADED TOP DOOR STAY

To suit a single oven

To suit a single oven and microwave

To suit a oven

To suit a double oven and microwave

Unit height 2120mm



Top Infill panel to suit

Bottom Infill panel 40mm


To suit a single oven at

595mm high

Unit height 2300mm







595mm high

Unit height 2120mm





Drawer height 140mm

Pan drawer height 355m


595mm high & microwave

from 382mm to 454mm

Unit height 2300mm





Drawer height 140mm




from 382mm to 454mm

Unit height 2120mm





Drawer height 140mm


To suit a double oven at

888mm high

Unit height 2300mm





Drawer height 140mm



888mm high

Unit height 2120mm


Top infill panel to suit





from 382mm to 454mm

Unit height 2300mm








from 382mm to 454mm

NOTE: TO ALLOW FOR THE TOP DOOR TO OPEN THE UNIT WILL BE FITTED WITH PUSH FIT HINGES AND CATCHES.





TALL HOUSING UNITS - CONTINUED

To suit a refrigerator and /or freezer


2300 HIGH

568 600 Lt Hd 4605 Lt Hd 4629

Rt Hd 4606 Rt Hd 4630

2120 high 2300 high

Unit height 2120mm




Aperture 1937mm

Unit height 2300mm




Aperture 2117mm

DETAIL SHOWING HOW THE LARDER, BROOM & FRIDGE FREEZERS WILL BE JOINTED TOGETHER

WIDTH 1970 HIGH 2150HIGH

64 ALUMINIUM 6360 6361

48 ALUMINIUM 6363 6364

VERTICAL SPACING BATTENS & ALUMINIUM TRIM FOR JOINTING LARDER, BROOM & FRIDGE FREEZERS

TALL UNITS

1: VERTICAL SPACING BATTEN MADE IN TWO PARTS FROM 16mm ALUMINIUM GREY MFC WITH 0.4 MATCHING PVC EDGING TO THE FRONT EDGES.

2: THE BATTENS ARE MADE IN ONE LENGTH TO SUIT THE 2150mm HIGH TALL UNIT. THE BATTEN IS THEN REDUCED IN HEIGHT TO SUIT THE 1970mm HIGH TALL UNIT BY THE FITTER ON SITE.

3: THE TWO PART TO BE SCREWED TOGETHER ON SITE BY THE FITTER AND FITTED FLUSH WITH THE FRONT EDGES OF THE TALL UNIT END PANEL..

4: THE ALUMINIUM TRIM TO BE FIXED TO THE FRONT EDGES OF THE TALL UNIT AND THE JOINTING BATTENS WITH DOUBLE SIDED TAPE.

5: WHEN DESIGNING THE KITCHEN WITH TALL UNIT ALLOW 32mm BETWEEN TALL UNITS FOR THE VERTICAL BATTENS,

NOTE: THE ALUMINIUM FRONT STRIPS ARE DESIGNED TO COVER THE FRONT EDGES OF THE BATTENS AND ADJACENT TALL UNIT END PANELS .

TALL UNIT FRIDGE- FREEZERS MUST BE SPECIFIED WITH VERTICAL ALUMINIUM STRIP, PLEASE SEE DETAIL BELOW

BATTEN

64MM WIDE ALUMINIUM TRIM, PLEASE SEE DETAIL BELOW

48MM WIDE ALUMINIUM TRIM FOR FITTING AT THE END OF A RUN OF TALL UNITS WITH ADJACENT

DECOR PANEL, PLEASE SEE DETAIL BELOW

DETAIL SHOWING TALL

FRIDGE / BROOM UNITS

WITH THE 64mm VERTICAL

ALUMINIUM TRIM & 32mm

SPACING BATTENS FITTED

DETAIL SHOWING END OF

RUN TALL FRIDGE / BROOM

UNIT WITH THE 48mm

VERTICAL ALUMINIUM TRIM

& 32mm SPACING BATTEN

BATTEN

NOTE: THE BATTEN IS INCLUDED IN THE CODE FOR THE ALUMINIUM TRIMS

DETAIL SHOWING TALL

FRIDGE - FREEZER UNIT

NEXT TO A TALL OVEN

HOUSING UNIT WITH THE

48mm VERTICAL ALUMINIUM

TRIM & 32mm SPACING

BATTEN

Detail showing the recessed handle for the Fridge

Freezer & Broom units


WALL UNITS - DUAL HANDED

With full-height, dual-handed doors

NOTE: IDEALLY USED ADJACENT TO A COOKER HOOD TO PREVENTDOOR CLASHES, OR INTO A CORNER ALSO TO PREVENT DOORCLASHES.

WIDTH 720 HIGH 720 HIGH 900 HIGH 900 HIGH

BOTTOM WITHOUT LIGHT RECESS BOTTOM WITH LIGHT RECESS BOTTOM WITHOUT LIGHT RECESS BOTTOM WITH LIGHT RECESS

800 Lt Hd 1437 Lt Hd 1637 Lt Hd 1457 Lt Hd1657

Rt Hd 1438 Rt Hd 1638 Rt Hd 1458 Rt Hd1658

900 Lt Hd 1439 Lt Hd 1639 N/A N/A

Rt Hd 1440 Rt Hd 1640 N/A N/A

1000 Lt Hd 1441 Lt Hd 1641 Lt Hd 1461 Lt Hd 1661

Rt Hd 1442 Rt Hd 1642 Rt Hd 1462 Rt Hd 1662

WALL UNITS with UPGRADE TOP DOOR STAY

With full-height, lift-up door

NOTE: ON 800MM AND 1000MM WIDE UNITS SOME RANGES MAY HAVE TWO DOORS ATTACHED TO EACH OTHER SIDE BY SIDE.NOTE: ON 800MM AND 1000MM WIDE UNITS THERE WILL BE AN INTERNAL SUPPORT RAIL BETWEEN THE TOP AND BOTTOM OF THE UNIT.WALLUNITS


BOTTOM WITHOUT LIGHT RECESS BOTTOM WITH LIGHT RECESS

500 1404 1604

600 1405 1605

800 1406 1606

1000 1407 1607

WALL UNITS 575mm HIGH


WALL UNITS


WIDTH 720 HIGH 720 HIGH 900HIGH 900HIGH

BOTTOM WITHOUT LIGHT RECESS BOTTOM WITH LIGHT RECESS BOTTOM WITHOUT LIGHT RECESS BOTTOM WITH LIGHT RECESS





450 Lt Hd 1427 Lt Hd 1627 N/A N/A

Rt Hd 1428 Rt Hd 1628 N/A N/A





800 1433 1633 1453 1653

900 1434 1634 N/A N/A

1000 1435 1635 1455 1655



300 Lt Hd 1409 Lt Hd 1609

Rt Hd 1410 Rt Hd 1610

400 Lt Hd 1411 Lt Hd 1611

Rt Hd 1412 Rt Hd 1612

450 Lt Hd 1413 Lt Hd 1613

Rt Hd 1414 Rt Hd 1614

500 Lt Hd 1415 Lt Hd 1615

Rt Hd 1416 Rt Hd 1616

600 Lt Hd 1417 Lt Hd 1617

Rt Hd 1418 Rt Hd 1618

800 1419 1619

900 1420 1620

1000 1421 1621

720 high 900 high

575 high 575 high

720 high 900 high

ALL WALL UNITS ARE HANDLE-LESS

Detail showing the side view of the wall unit

Note: the double bottom panels this is to allow a finger space to open the door.

Detail showing the optional bottom panel with lighting hole and channel, this will

allow for one down lighter per unit, hole size for the light = 58mm dia.

RECESS SPOTLIGHTS & TRANSFORMERS ARE NOT PART OF THE UNIT CODE AND WILL NEED TO BE SPECIFIED :

CODE FOR THE LED RECESS SPOTLIGHT ACCS180A

CODE FOR THE LED DRIVER / TRANSFORMER ACCS181A WITH 1.8 OF MAINS LEAD

NOTE: MAXIMUM 4 SPOTLIGHT PER LED DRIVER / TRANSFORMER


WALL BOILER HOUSING UNITS




316 500 Lt Hd 8795 Lt Hd 8895

Rt Hd 8796 Rt Hd 8896

600 Lt Hd 8797 Lt Hd 8897

Rt Hd 8798 Rt Hd 8898

420 500 Lt Hd 8765 Lt Hd 8965

Rt Hd 8766 Rt Hd 8966

600 Lt Hd 8761 Lt Hd 8961

Rt Hd 8762 Rt Hd 8962

WALL MICROWAVE HOUSING UNIT with UPGRADED TOP DOOR STAY

To suit 316mm deep wall units

NOTE: THE MICROWAVE MANUFACTURER AND MODEL NUMBER MUST BE SPECIFIED SO THAT THE INFILL CAN BE MANUFACTURED TO SUIT.NOTE: TO ALLOW FOR THE DOOR TO OPEN THE UNIT WILL BE FITTED WITH PUSH FIT HINGES AND CATCHES.NOTE: LIGHTING FOR THESE UNITS IS NOT AVAILABLE


500 1463 1465

600 1464 1466

720 high 900 high

INTEGRATED EXTRACTOR HOOD

NOTE: 450MM HIGH TO SUIT 720MM WALL UNITS.NOTE: WHEN USING 900MM WALL UNITS, AN INTEGRATED EXTRACTOR HOOD INFILL PANEL MUST BE SPECIFIED (SEE BELOW).

INTEGRATED EXTRACTOR HOOD INFILL PANEL

NOTE: 175MM INFILL TO BE USED IN CONJUNCTION WITH INTEGRATED EXTRACTOR HOOD TO SUIT 900MM WALL UNITS.

TELESCOPIC COOKER HOOD

NOTE: TO ALLOW FOR THE DOOR TO OPEN THE UNIT WILL BE FITTED WITH PUSH FIT HINGES AND CATCHES.

NOTE: THESE COOKER HOODS CAN NOT BE USED WITH GAS HOBS AS IT WILL BREACH CORGI REGULATIONS AND BS6172. ELECTRIC, CERAMIC AND INDUCTION HOBS ARE FINE.

NOTE: INTERNAL WALL UNIT SHELVING IS REDUCED DEPTH TO ALLOW FOR EXTRACTOR MECHANISM; BEST SUITED FOR USE WITH SMALLSPICE JARS, ETC.

WIDTH 450 HIGH

600 CH700

WIDTH 175 HIGH

600 8168

WIDTH 575 HIGH 720 HIGH 900 HIGH

600 wide 600 wide900 wide 900 wide

600 Lt Hd 1467 Lt Hd 1469 N/A

Rt Hd 1468 Rt Hd 1470 N/A

900 1471 1472 N/A

NOTE: THE HEIGHT OF THE TELESCOPIC HOODWILL BE CALCULATED TO ALLOW FORTHE BOTTOM EDGE OF THE HOODSPULL-OUT TRIM TO FINISH FLUSHWITH THE THE BOTTOM EDGE OF THEADJACENT WALL UNITS.


WALL CORNER UNITS

With full-height door - 600mm carcase width




720 high 900 high

720 high 900 high

720 high 900 high

DOOR WIDTH WIDTH 575 HIGH 575 HIGH


300 600 Lt Hd 1473 Lt Hd 1673

(min 36-78) Rt Hd 1474 Rt Hd 1674

575 high



500 1501 1701

600 1502 1702

800 1503 1703

1000 1504 1704

HORIZONTAL OPENING DUAL HANDED WALL UNITS

NOTE: TO ALLOW FOR THE TOP DOOR TO OPEN THE UNIT WILL BE FITTED WITH PUSH FIT HINGES ANDCATCHES.

WALL CORNER UNIT 575mm HIGH


UNITS

DOOR WIDTH 720 HIGH 900 HIGH 720 HIGH 900 HIGH

BOTTOM WITHOUT LIGHT RECESS BOTTOM WITHOUT LIGHT RECESS BOTTOM WITH LIGHT RECESS BOTTOM WITH LIGHT RECESS


(min 36-78) Rt Hd 1476 Rt Hd 1490 Rt Hd 1676 Rt Hd 1690



450 Lt Hd 1479 N/A Lt Hd 1679 N/A

(min 186-228) Rt Hd 1480 N/A Rt Hd 1680 N/A


(min 236-278) Rt Hd 1482 Rt Hd 1494 Rt Hd 1682 Rt Hd1694

500 Lt Hd 1483 Lt Hd 1495 Rt Hd 1683 Lt Hd 1695


600 Lt Hd 1485 Lt Hd 1497 Rt Hd 1685 Lt Hd 1697





WALL UNIT INFILL PANELS

NOTE: TO BE ASSEMBLED AND CUT DOWN ON-SITE TO REQUIRED WIDTH.NOTE: MINIMUM WIDTH IS 16MM.

WINDOW SOFFITS

Without pelmet

NOTE: SUPPLIED READY TO BE CUT TO SIZE ON-SITE.


150 8754 8930

300 8753 8931

400 8096 8097


DEPTH WIDTH CODE

316 1200 6312

1600 6316

2000 6320

2400 632416mm soffit panel


636 X 636 6018 6023

WALL CORNER POST

NOTE: A CORNER POST IS FITTED BETWEEN TWO ADJACENT UNITS WHERE A VOID SPACE IS CREATED IN THE CORNER.

WALL UNIT GLASS SHELVES

To suit 316mm deep wall units - Optional extra

NOTE: SUPPLIED WITH GLASS SHELF CLIPS.NOTE: SHELF WIDTH ANNOTATED IS NOMINAL TO SUIT UNITS.NOTE: 800 AND 1000MM WALL DISPLAY BI-FOLDING UNITS CANNOT BE UPGRADED TO HAVE INTERNAL GLASS SHELVING.

WIDTH CODE

400 GLAS070B

500 GLAS071A

600 GLAS072A

800 GLAS073A

900 GLAS069A

1000 GLAS074A


VERTICAL BASE UNIT DECOR PANEL (Available in all Price Groups)

NOTE: THE STYLE OF THE DECOR PANELS WILL DIFFER ACCORDING TO THE RANGE CHOICES.

NOTE: PANEL DEPTH: D 591

NOTE: PANEL DEPTH: D 641 TO SUIT 650 DEEP WORKTOPS

VERTICAL TALL UNIT DECOR PANEL (Available in all Price Groups) HEIGHT DEPTH 16mm PANEL

FOR 2156mm 591 8017

TALL UNITS 641 8265

FOR 2336mm 591 8067

TALL UNITS 641 8267

HEIGHT DEPTH 16mm PANEL

NEW 935 591 8215

641 8216

Decor panel style. Decor Panels are Range

Dependent;

They are manufactured from

either MFC panels, Foil

Wrapped panels all with a

PVC edge.


Dependent;




PVC edge.


Dependent;




PVC edge.

NOTE: FOR ‘16MM THICK’,

DECOR PANELS FOR 2120MM TALL UNITS ARE PROVIDED 2150MM HIGH,

AND DECOR PANELS FOR 2300MM ARE PROVIDED 2330MM HIGH.

VERTICAL BASE PENINSULAR UNIT DECOR PANEL (Available in all Price Groups)

NOTE: THE STYLE OF THE DECOR PANELS WILL DIFFER ACCORDING TO THE RANGE CHOICES.

NOTE: PANEL DEPTH: D 646

HEIGHT DEPTH 16mm PANEL

NEW 935 646 8218

MANHATTAN SPECIFIER’S GUIDE 17MANHATTAN SPECIFIER’S GUIDE17 MANHATTAN SPECIFIER’S GUIDE 1717

DECOR PANEL SELF-ADHESIVE COVER CAPS

Self-Adhesive PVC cover caps:

For use when fitting Decor Panels to units, or to cover

the cam in the Wall Unit bottom panel.

VERTICAL VARIABLE SIZE DECOR PANEL (Available in all Price Groups)

NOTE: MAXIMUM BOARD SIZE = 2300 X 1200MM, WITH THE GRAIN FOLLOWING THE LONGEST LENGTH.

NOTE: LENGTH, HEIGHT AND GRAIN DIRECTION MUST BE SPECIFIED WHEN ORDERING.

HORIZONTAL VARIABLE SIZE FRAMING PANEL (Available in all Price Groups)

NOTE: LENGTH, HEIGHT AND GRAIN DIRECTION MUST BE SPECIFIED WHEN ORDERING.

HEIGHT 16mm PANEL

VARIABLE 9021

COLOUR CODE

COLOUR CODE

WHITE PLAS267A

VANILLA PLAS265A

ALUMINIUM PLAS270A

GREY

OAK PLAS269A

BEECH PLAS266A

MAPLE PLAS262A

NATURAL AIDA PLAS268A

WALNUT

FERRARA OAK PLAS261A


Dependent;




PVC edge.

Decor panel style.

Decor Panels are Range

Dependent;


either MFC panels, Foil Wrapped

panels all with a PVC edge.

DEPTH LENGTH 16mm PANEL

VARIABLE VARIABLE 8066

339 DEEP

PROTECTION PACKS

NOTE: IDEALLY TO BE FITTED EITHER SIDE F

CODES

6900 PROTECTION PACK

12 METERS OF BUBBLE WRAP 750 WIDE

12 METERS OF CORRUGATED CARDBOARD

2 POLY BAGS



12 METERS OF CORRUGATED CARDBOARD

20 LENGTHS OF PROPLEX / CORREX 600 X 1200 X 2mm

10 LENGTHS OF NOMAFOAM U-CHANNEL

2 POLY BAGS




10 LENGTHS OF NOMAFOAM U-CHANNEL

2 POLY BAGS




2 POLY BAGS

6905 FIRE PROTECTION PACK

2 ROLLS OF PROMESH = 1.5mm WIDE X 10m LONG


CODE

*White

FACM060A

**Silver

FACM082B

**Gold

FACM083A

**White

FACM084A

CORNICE STYLE, material and finish specific to individual range.

Style, material and finish specific to

individual range.

CODE

2.3 meters

6061

BREAKFAST BAR LEGS - 895MM HIGH

895mm x 25mm diameter chrome

plated steel tube with sockets.

CODE

Chrome

LEGS036A

CONTINUOUS PLINTH - 150MM HIGH

Colour specific to individual

range, supplied in 2.5m lengths

Optional extra,

manufactured from MFC, supplied in

2.5m lengths

Optional extra,

manufactured from MFC,supplied in

2.5m lengths

CODE

Range

specific

6094

Aluminium

effect

6083

White High

Gloss

6087


870mm x 60mm diameter, adjustable

height leg.

CODE

White

LEGS032A

S/Steel

LEGS035A

Oak

LEGS031A

STAINLESS STEEL PILASTERS

Manufactured from 50 x 100mm

tubing.

CODE

870mm

FACM232A

720mm

FACM233A

900mm

FACM234A

PLINTH SEALER

Transparent plastic extrusion which

clips to the bottom edge of the plinth.

The flexible lip then seals the gap

between the floor and the plinth.

NOTE: SUPPLIED IN 3M LENGTHS, CUT ON SITE TO SUITREQUIREMENTS.

CODE

PLAS250A

HALF SWING-OUT WIRE BASKETS

For use in a base corner units 2663/64

2627/28 & 2189/90 only.

NOTE: SUPPLIED AS A PAIR.

CODE

MECH001A

8 mm THICK WORKTOP UPSTANDS

For positioning directly above the worktop

The size 100mm high x 3000mm MAX long

CODE

9199

PLINTH AND WORKTOP VENTILATION GRILLS

To be fitted into a housing unit plinth or

fitted into a worktop over a highboard

housing unit.

NOTE: * MANUFACTURED FROM PLASTIC.

NOTE: ** MANUFACTURED FROM ALUMINIUM, AND

THEN SPRAYED THE APPROPRIATE COLOUR.

12V /1.25W LED RECESS SPOTLIGHT WITH 18 DIODES

EACH LED LIGHT SUPPLIED WITH 2M OF LEAD AND CONNECTOR

CODE

ACCS180A

240V / 6W LED SPOTLIGHT DRIVER / TRANSFORMER

EACH DRIVER / TRANSFORMER SUPPLIED WITH 1.8 OF BARE

ENDED MAINS LEAD

NOTE: MAXIMUM OF 4 LED LIGHTS PER DRIVER / TRANSFORMER

CODE

ACCS181A


710mm x 60mm diameter, adjustable

height leg.

CODE

White

LEGS030A

S/Steel

LEGS034A

Oak

LEGS033A


CODE

175 deg

HINGE OPTION TWO

DOUBLE POSTFORMED WORKTOPS

NOTE: 3.6M MAXIMUM LENGTH

38MM

Depth

670mm.

9088

Depth

900mm.

9089

2MM ACRYLIC EDGED WORKTOPS

2mm Acrylic edged laminate worktop,

acrylic edging available in:

- Aluminium Wave

- Beech multiplex

- Beech/Steel multiplex

- Walnut/Steel multiplex

- Planked Cherry


CODE

Depth up

to 850mm.

9120

SQUARE EDGED WORKTOPS

38mm Square edged laminate worktop


CODE

Depth up

to 850mm.

9061

HINGE OPTION THREE CODE

107 deg

WORKTOP CONNECTOR BOLTS

Each joint consists of a three butterfly

bolts to be recessed into the worktop

CODE

FACM009A

CABLE MANAGEMENT FOR LIGHTING - SELF ADHESIVE BASE

To be used in conjunction with cable ties

.

CODE

FITT091A

HINGE OPTION FOUR CODE

107 deg

Soft Close

HINGE OPTION SIX CODE

175 deg

Soft Close

CABLE MANAGEMENT FOR LIGHTING - CABLE TIE

To be used in conjunction with Self Adhesive bases

.

CODE

FITT090A

SOFT CLOSING DOORS - UPGRADE OPTION Available with to suit

Available with to suit all base, wall, highboard and tall units as

an optional upgrade

NOTE: NOT SUITABLE FOR BI-FOLD WALL UNITS

CODE

HING064A

TIMBER BATTENS

50 x 50 x 2400mm timber batten for

supporting 650mm deep of Granite

worktops.

20 x 50 x 2400mm timber batten for

supporting worktops over appliance

spaces, soffit panels or infill panels.

CODE

50x50x2400

TIMB021A

20x50x2400

TIMB020A

SINGLE POSTFORMED WORKTOPS

38mm & 60mm Single postformed laminate worktop


38MM

Depth up

to 600mm.

9086

Depth 601-

850mm.

9087

ENTRY LEVEL DRAWER UNITS WITH SINGLE-WALLED, SOFT

CLOSING DRAWERS - UPGRADE OPTION

Available as an upgrade option to all base and tall units

CODE

SDRAWER10

SOFT CLOSING DRAWERS - UPGRADE OPTION

DRAWER UNITS WITH TWIN-WALLED, FULL EXTENSION

Available as an upgrade option to all base and tall units

NOTE: THIS COMES AS STANDARD ON THE FULL EXTENSION DRAWERS

CODE

MECH126A

Linea Handle-less Kitchens

F16 DESCRIPTION Horizontal wood-grain effect

MFC door with 2mm matching

PVC edgingCOLOURS DriftwoodCARCASE Aluminium Grey, Latte or

White MFC

F16DESCRIPTION Horizontal wood-grain effect


PVC edgingCOLOURS Plum WoodCARCASE Aluminium Grey, Latte or

White MFC

F16DESCRIPTION Horizontal wood-grain effect


PVC edgingCOLOURS Ontario WalnutCARCASE Aluminium Grey, Latte or

White MFC

F07 DESCRIPTION Plain colour MFC door with

2mm matching PVC edgingCOLOURS LavaCARCASE Aluminium Grey, Latte or

White MFC

Price

Group

FH11DESCRIPTION Gloss ‘Slab-effect’ MFC door

with 2mm matching PVC edg-

ingCOLOURS Gloss AubergineCARCASE Aluminium Grey, Latte or

White MFC

H11DESCRIPTION Gloss ‘Slab-effect’ MFC door


ingCOLOURS Iridescent Gloss AnthraciteCARCASE Aluminium Grey, Latte or

White MFC



ingCOLOURS Gloss MochaCARCASE Aluminium Grey, Latte or

White MFC



ingCOLOURS Gloss LatteCARCASE Aluminium Grey, Latte or

White MFC

H16DESCRIPTION Gloss ‘Slab-effect’ design

door with Glass effect PVC

edgingCOLOURS Gloss BlackCARCASE Aluminium Grey, Latte or

White MFC

Price

Group

HH16DESCRIPTION Gloss ‘Slab-effect’ design


edgingCOLOURS Gloss MagnoliaCARCASE Aluminium Grey, Latte or

White MFC



edgingCOLOURS Gloss RedCARCASE Aluminium Grey, Latte or

White MFC



edgingCOLOURS Gloss WhiteCARCASE Aluminium Grey, Latte or

White MFC

H18DESCRIPTION Gloss Vertical wood -grain

effect MFC door, with match-

ing edgingCOLOURS Gloss OliveCARCASE Aluminium Grey, Latte or

White MFC

H19DESCRIPTION Gloss Horizontal wood-grain


ing edgingCOLOURS Gloss CordobaCARCASE Aluminium Grey, Latte or

White MFC

H19 DESCRIPTION Gloss Horizontal wood-grain

effect MFC door, with matching

edgingCOLOURS Gloss WengeCARCASE Aluminium Grey, Latte or

White MFC



ing edgingCOLOURS Gloss PlumCARCASE Aluminium Grey, Latte or

White MFC



ing edgingCOLOURS Gloss Silver OakCARCASE Aluminium Grey, Latte or

White MFC

M12 DESCRIPTION High gloss ‘Slab-effect’

design doorCOLOURS High Gloss BlackCARCASE Aluminium Grey, Latte or

White MFC


design doorCOLOURS High-Gloss LatteCARCASE Aluminium Grey, Latte or

White MFC


design doorCOLOURS High-Gloss IvoryCARCASE Aluminium Grey, Latte or

White MFC


design doorCOLOURS High-Gloss WhiteCARCASE Aluminium Grey, Latte or

White MFC

Price

Group

M

Product Selector for 2011

Date post:	08-Mar-2016
Category:	Documents
Upload:	alan-margetts
View:	226 times
Download:	0 times

Linea Handless Range units

Documents