SWISS MADE LINEAR TECHNOLOGY
LMLINEAR MODuLESExCERpT fROM MAIN CATALOGuEV 11-15
5www.linetech.ch
LM
LINE TECH LINEar ModuLES LM
Table of contents
– Product overview _____________________________________________________6–7– Design fundamentals / Lubrication / Maintenance ____________________________8– Profile cross-sections ________________________________________________ 9–11– Linear module with ball screw drive; details for ball screw drive ________________12– Linear module with toothed belt drive; details for toothed belt drive ____________13– Linear module with ball screw drive; general technical details __________________14– Linear module with toothed belt drive; general technical details ________________15– Linear module with ball screw drive; load ratings and torques _________________16– Linear module with toothed belt drive; load ratings and torques _______________17– Linear module with ball screw drive; permissible speeds ______________________18– Linear module with toothed belt drive; permissible speeds ____________________19– Linear module with ball screw drive; permissible deflection ____________________20– Linear module with toothed belt drive; permissible deflection __________________21
– Linear modules with ball screw drive - Designation system _______________________________________________ 22–23 - Information for selection » Motor mounting preparation _____________________24 - Dimensions LM3…BR…N (with steel strip) ________________________________26 - Dimensions LM3…BR…L/R ___________________________________________27 (with lateral support rail left/right, with steel strip) - Dimensions LM4…BR…N (with steel strip) ________________________________28 - Dimensions LM4…BR…L/R ___________________________________________29 (with lateral support rail left/right, with steel strip) - Dimensions LM5…BR…N (with steel strip) ________________________________30 - Dimensions LM5…BR…L/R ___________________________________________31 (with lateral support rail left/right, with steel strip)
– Linear modules with toothed belt drive - Designation system _______________________________________________ 32–33 - Information for selection » Motor mounting preparation _________________ 34–36 - Dimensions LM3…NZ…N (without protective strip) _________________________38 - Dimensions LM3…BZ…N (with steel strip) ________________________________39 - Dimensions LM3…NZ…L/R ___________________________________________40 (with lateral support rail left/right, without protective strip) - Dimensions LM3…BZ…L/R ___________________________________________41 (with lateral support rail left/right, with steel strip) - Dimensions LM4…NZ…N (without protective strip) _________________________42 - Dimensions LM4…BZ…N (with steel strip) ________________________________43 - Dimensions LM4…NZ…L/R ___________________________________________44 (with lateral support rail left/right, without protective strip) - Dimensions LM4…BZ…L/R ___________________________________________45 (with lateral support rail left/right, with steel strip) - Dimensions LM5…NZ…N without protective strip) _________________________46 - Dimensions LM5…BZ…N (with steel strip) ________________________________47 - Dimensions LM5…NZ…L/R ___________________________________________48 (with lateral support rail left/right, without protective strip) - Dimensions LM5…BZ…L/R ___________________________________________49 (with lateral support rail left/right, with steel strip)
– Limit switch; fitting / preparation / plug connector _______________________ 50–51– Motor mounting straight/lateral with ball screw drive _____________________ 52–53– Motor mounting straight/lateral with toothed belt drive ___________________ 54–56– Attachment accessories; clamps / sliding blocks ________________________ 58–59– Grease points _____________________________________________________ 60–61
6 LINE TECH – SWISS MADE LINEAR TECHNOLOGY
LM
LINEar ModuLES
Product overview
LM…R…N Linear module with ball screw drive
LM…R…L/R Linear module with ball screw drive and lateral support rail left/right
LM…Z…N Linear module with toothed belt drive
LM…Z…L/R Linear module with drive belts and lateral support rail left/right
7www.linetech.ch
H
B
H
B
LM
LINEar ModuLES
LINE TECH linear modules are precision, ready-to-install, modular linear systems with linear guide and two drive variants, ball screw or toothed belt drive. Linear systems with longer strokes and high movement speeds are typical application areas. Three sizes are currently available (LM3, LM4 und LM5).
Advantages
– Compact dimensions– Optimum running performance together with high load ratings and high level of rigidity with either one or two integrated, no-play linear guides– Either ball screw or toothed belt drive– Simple motor mounting by centering and thread on driving head– Greasing by central grease points– Design aligned to application possible
Structure
– Compact aluminium base profile– Ready-to-install linear modules in any lengths– Carriage made of aluminium
Customised options
– Motor mounting– Limit switch– Multi-axis systems
Please refer to pages 12 to 17 for load capacities.
Product overview
Linear modul Dimensions Load ratings
Type B x H [mm]
C0[kN]
C[kN]
LM3…N 60 x 85 35.0 18.0
LM3…L/R 98 x 94 70.0 36.0
LM4…N 80 x 100 59.9 34.2
LM4...L/R 117 x 109 119.9 68.4
LM5...N 110 x 129 85.0 49.6
LM5...L/R 155 x 141 170.0 99.2
8 LINE TECH – SWISS MADE LINEAR TECHNOLOGY
1)
2)
3a)
4)1)
2)
3b)
4)
LM
LINEar ModuLES
Design fundamentals / Lubrication / Maintenance
LINE TECH linear modules
LINE TECH linear modules with ball screw or toothed belt drive are modular, ready-to-install linear units with drive. Sealed rail guiding elements are em-ployed in all sizes.Guides and drive are protected from ex-ternal factors (such as dirt and chippings) by a steel strip / the toothed belt.The base profile is made of aluminium alloy and manufactured with the extrusion process.Additional limit switches fitted on the outside, in conjunction with motors and a controller, ensure correct positioning of the carriage and provide protection against overrun.The selected design provides for a high level of performance with the most com-pact dimensions.
Lubrication
LINE TECH linear modules are lubricated with Microlube GBU Y 131 at the factory. This quality grease offers outstanding properties for the guidance and screw drive elements as well.Greasing should be carried out at regular intervals, depending on the load and area of operation. On an average, re-greasing is required every 500 hours.All roller bearings are greased for life and thus do not require any maintenance. Correct and sufficient greasing can substantially prolong the life of linear mo-dules.
Note: Also follow here the instructions on the lubrication points (pages 60/61).
Maintenance
LINE TECH linear modules are main-tenance-free (apart from re-greasing required).
Service temperature
The permissible operating temperature (between 5 and 80 °C) is determined by the synthetic materials used.The specifications of the relevant manu-facturers apply for motors and control units.
1) Base profile2) Carriage
3a) Ball screw drive3b) Toothed belt drive
4) Linear guide
LM…R…with ball screw drive
LM…Z…with toothed belt drive
9www.linetech.ch
C
A
A
40
1826
31
46
20
65
85
46
40
65
1826
85
A
A
C
98
40
65
1826
94
A
A
A
A
A
A40
1826
20
65
98
94
A C
5
11.7
1.8
6.35
5
11.7
2.5
7.05
LM
LM3…Z…N
Profile cross-sections LM3…R/Z…
LM3…R…L/Rwith lateral support rail left/right
LM3…R…N
LINEar ModuLES
LM3…Z…L/Rwith lateral support rail left/right
Grooves LM3…
10 LINE TECH – SWISS MADE LINEAR TECHNOLOGY
C
B2142
53
30
60
45.5
80
100
53
80
2142
100
60
45.5
B
C
53
80
117
21
45.5
42
109
C
B
B
C
2142
53
30
45.5
117
80
109
CB
5
11.7
2.5
7.05
16.4
6.2
3
9.75
LM
LM4…Z…N
Profile cross-sections LM4…R/Z…
LM4…R…L/Rwith lateral support rail left/right
LM4…R…N
LINEar ModuLES
LM4…Z…L/Rwith lateral support rail left/right
Grooves LM4…
11www.linetech.ch
60
85
204525
129
85
22 2220
110
FE
D
85
110
85
2560 20
45
129
E
D
F 85110
4525
155
60 20
141
E
D
F
60
85
204525
141
110
155
E
F
D
E FD
8
12
4.25 7 10
820
4.25
12
511
2.5
7.05
LM
LM5…Z…N
Profile cross-sections LM5…R/Z…
LM5…R…L/Rwith lateral support rail left/right
LM5…R…N
LINEar ModuLES
LM5…Z…L/Rwith lateral support rail left/right
Grooves LM5…
12 LINE TECH – SWISS MADE LINEAR TECHNOLOGY
LM
LINEar ModuLES wITH baLL SCrEw drIVE
Details for ball screw drive
LM BSD Axial load rates
Positioning accuracy
Repeating accuracy
Accelera-tion
Axial play Idletorque
Size d x p C0 Cdyn amax Type Axial play
[mm] [N] [N] [μm /mm] [mm] [m /s2] [mm] [Nm]
LM3...R...
16 x 5 4 551 4 327 52 / 300< 0.03 1)
10.0R < 0.02 0.030
< 0.01 1) V — 0.100
16 x 10 4 551 4 327 52 / 300< 0.03 1)
10.0R < 0.02 0.060
< 0.01 1) V — 0.200
16 x 16 4 551 4 327 52 / 300< 0.03 1)
10.0R < 0.02 0.120
< 0.01 1) V — 0.320
LM4...R...
20 x 5 5 705 4 912 52 / 300< 0.03 1)
10.0R < 0.02 0.050
< 0.01 1) V — 0.120
20 x 20 5 705 4 912 52 / 300< 0.03 1)
10.0R < 0.02 0.200
< 0.01 1) V — 0.400
LM5...R...
32 x 5 11 538 8 947 52 / 300< 0.03 1)
10.0R < 0.02 0.080
< 0.01 1) V — 0.200
32 x 10 11 538 8 947 52 / 300< 0.03 1)
10.0R < 0.02 0.160
< 0.01 1) V — 0.400
32 x 32 11 538 8 947 52 / 300< 0.03 1)
10.0R < 0.02 0.600
< 0.01 1) V — 1.200
Details for ball screw drive (BSD)
d x p = screw diameter x thread pitch 1) backlash not factored in R = reduced axial playV = preloaded
13www.linetech.ch
LM
LINEar ModuLES wITH TooTHEd bELT drIVE
Details for toothed belt drive
LM Toothed belt drive Axial load
Positioning accuracy
Repeating accuracy
Accel-eration
Size Type/division Pinion Stroke/rev Tension 3) F … /1000 mm amaxd3 x lR [mm] [mm] [mm/m] [N] [μ /mm] [mm] [m/s
2]
LM3…Z… HTD 5 M 49.34 x 31 155 0.245 … 1) 200/1000 2) < 0.20 2) 50.0 1)
LM4...Z... HTD5M 65.25 x 45 205 0.105 … 1) 200/1000 2) < 0.20 2) 50.0 1)
LM5...Z... STD8M 94.22 x 60 296 0.059 … 1) 200/1000 2) < 0.20 2) 50.0 1)
Details for toothed belt drive
d3 x lR = pinion diameter x pinion width 1) dependent on speed and load ➞ see diagram on page 19 2) backlash not factored in3) belt tension/metre [mm/m] per 100 N tensile force
14 LINE TECH – SWISS MADE LINEAR TECHNOLOGY
LM
LINEar ModuLES wITH baLL SCrEw drIVE
General technical details for linear modules
2) for ball screw drive, dependent on rotational speed characteristics, spindle length and relevant critical rotational speed.
LM Movement speed
Moments of inertia
Strokemax.
Steel strip feed and friction force
Moved mass
Guide Drive
Type vmax vmax IY IZ FV mb
[m/s] [m/s] [cm4] [cm4] [mm] [N] [kg]
LM3…R…N 5.0 2) 64.5 81.7 2 000without 20.00
1.410with 30.00
LM3…R…L/R 5.0 2) 64.8 81.9 2 000without 40.00
2.515with 50.00
LM4…R…N 5.0 2) 106.5 152.7 3 000without 25.00
2.500with 35.00
LM4…R…L/R 5.0 2) 107.6 153.4 3 000without 50.00
4.225with 60.00
LM5…R…N 5.0 2) 432.7 594.0 3 000without 30.00
5.330with 40.00
LM5…R…L/R 5.0 2) 434.6 595.3 3 000without 60.00
8.820with 70.00
General technical details for linear modules with ball screw drive
Y
Z
15www.linetech.ch
LM
LINEar ModuLES wITH TooTHEd bELT drIVE
General technical details for linear modules
4) for toothed belt drive, dependent on load and speed and permissible movement speed of the linear guide ➞ see diagram on page 195) variant without drive
LM Movement speed
Moments of inertia
Strokemax.
Steel strip feed and friction force
Moved mass
Guide Drive
Type vmax vmax IY IZ FV mb
[m/s] [m/s] [cm4] [cm4] [mm] [N] [kg]
LM3…N…N 5) 5.0 4) 66.9 82.4 7 650without 20.00 1.030
with 30.00 1.040
LM3…Z…N 5.0 4) 66.9 82.4 7 650without 20.00 1.100
with 30.00 1.110
LM3…Z…L/R 5.0 4) 67.2 82.6 7 650without 40.00 2.205
with 50.00 2.215
LM4…N…N 5) 5.0 4) 131.2 197.8 7 580without 25.00 2.090
with 35.00 2.100
LM4…Z…N 5.0 4) 131.2 197.8 7 580without 25.00 2.150
with 35.00 2.165
LM4…Z…L/R 5.0 4) 132.3 198.5 7 580without 50.00 3.875
with 60.00 3.890
LM5…N…N 5) 5.0 4) 451.9 623.9 7 530without 30.00 4.000
with 40.00 4.040
LM5…Z…N 5.0 4) 451.9 623.9 7 530without 30.00 4.100
with 40.00 4.140
LM5…Z…L/R 5.0 4) 453.8 625.2 7 530without 60.00 7.590
with 70.00 7.630
General technical details for linear modules with toothed belt drive
Y
Z
16 LINE TECH – SWISS MADE LINEAR TECHNOLOGY
Cy1 Cy2
Cz1Cz2
MX
MZ
MY
MX
MZ
MY
LM
LINEar ModuLES wITH baLL SCrEw drIVE
LM…R…L/Rwith lateral support rail
LM…R…N
Note on dynamic load ratings and torques
The determination of dynamic load rat-ings and torques is based on a 50, 000 m stroke. If comparative values must be
calculated for a 100, 000 m stroke, the values for Mx, My, Mz and C must be divided by the factor 1.26.
Load ratings
Expedient load
With a view to service life, loads of less than 20% of the dynamic load ratings have generally proved to be expedient.
Linear modul Maximum permissible load [kN] Maximum permissible torque [Nm]
Type static dynamic static dynamic
Cy0 1,2 Cz0 1,2 Cy1,2 Cz1,2 Mx0 My0 Mz0 Mx My Mz
LM3…R…N 35.0 35.0 18.0 18.0 286 1 353 1 353 160 1 030 880
LM3…R…L/R 70.0 70.0 36.0 36.0 1 456 2 778 2 778 808 2 016 2 016
LM4…R…N 59.9 59.9 34.2 34.2 646 1 573 1 573 400 1 446 1 446
LM4…R…L/R 119.9 119.9 68.4 68.4 3 030 3 860 3 860 1 868 3 432 3 432
LM5…R…N 85.0 85.0 49.6 49.6 1 080 2 316 2 316 684 2 290 2 290
LM5…R…L/R 170.0 170.0 99.2 99.2 5 588 8 715 8 715 3 552 7 659 7 659
Torques
Torques and load ratings
17www.linetech.ch
Cy1 Cy2
Cz1Cz2
MX
MZ
MY
MX
MZ
MY
LM
LINEar ModuLES wITH TooTHEd bELT drIVE
LM…Z…L/Rwith lateral support rail
LM…Z…N
Torques
Load ratings
Linear modul Maximum permissible load [kN] Maximum permissible torque [Nm]
Type static dynamic static dynamic
Cy0 1,2 Cz0 1,2 Cy1,2 Cz1,2 Mx0 My0 Mz0 Mx My Mz
LM3…Z…N 35.0 35.0 18.0 18.0 286 1 185 1 185 160 923 923
LM3…Z…L/R 70.0 70.0 36.0 36.0 1 457 2 610 2 610 808 1 998 1 998
LM4…Z…N 59.9 59.9 34.2 34.2 646 2 484 2 484 400 2 130 2 130
LM4…Z…L/R 119.9 119.9 68.4 68.4 3 030 4 772 4 772 1 868 4 115 4 115
LM5…Z…N 85.0 85.0 49.6 49.6 1 080 6 115 6 115 684 5 170 5 170
LM5…Z…L/R 170.0 170.0 99.2 99.2 3 356 12 513 12 513 2 136 10 541 10 541
Torques and load ratings
18 LINE TECH – SWISS MADE LINEAR TECHNOLOGY
200 400 600 800 20001000 1200 1400 1600 1800 2200 2400 2600
10
vmax [m/min]
L [mm]
2030405060708090
100
16x5
16x10
16x16
200 400 600 800 20001000 1200 1400 1600 1800 2200 2400 2600
10
vmax [m/min]
L [mm]
2030405060708090
100
20x5
20x10
20x20
200 400 600 800 20001000 1200 1400 1600 1800 2200 2400 2600
10
vmax [m/min]
L [mm]
2030405060708090
100
32x32
32x20
32x10
32x5
LM
Permissible speeds
Permissible speeds...
Caution: For ball screw drive, note the rotational speed characteristics, spindle length and relevant critical rotational speed.
Please also pay attention to the motor speeds.
LINEar ModuLES wITH baLL SCrEw drIVE
… for linear module LM4…R… with ball screw drive ø 20 x … 1)
… for linear module LM3…R… with ball screw drive ø 16 x … 1)
… for linear module LM5…R… with ball screw drive ø 32 x … 1)
1) greater accuracy on requestL = overall length of the linear module
19www.linetech.ch
20406080
100120140160180200220240260280300
600
800
1000
1200
1400
1600
1800
2000
2200
2400
2600
2800
3000
3200
3400
3600
vmax [m/min]
F [N]
LM3 LM4 LM5
vmax
LM
Permissible speeds
Permissible speeds...
Caution: For toothed belt drive, the permitted movement speed of the linear guide, and load, are authoritative.
Please also pay attention to the motor speeds.
LINEar ModuLES wITH TooTHEd bELT drIVE
… for linear module LM…Z… with toothed belt drive
F = axial load
20 LINE TECH – SWISS MADE LINEAR TECHNOLOGY
f max
LM / 2
LM
F
250 500 750 1000 25001250 1500 1750 2000 2250 2750 3000 3250 3500
0.4
0.8
1.2
0.2
0.6
1.0
fmax [mm]
LM [mm]
fmax
2500
N
2000
N
1500 N
1000 N
500 N
250 N
0 N
250 500 750 1000 25001250 1500 1750 2000 2250 2750 3000 3250 3500
0.4
0.8
1.2
0.2
0.6
1.0
fmax [mm]
LM [mm]
fmax
2500
N20
00 N 150
0 N 1000 N 500
N
250 N
0 N
250 500 750 1000 25001250 1500 1750 2000 2250 2750 3000 3250 3500
0.4
0.8
1.2
0.2
0.6
1.0
fmax [mm]
LM [mm]
fmax
2500
N
2000
N150
0 N100
0 N
500 N
250 N
0 N
LM
Permissible deflectionwith ball screw drive
Linear modules may be assembled self-supporting. However, the deflection (which limits the possible load) must be taken into consideration.
If the maximum permissible deflection is exceeded, the linear modules must be additionally supported.
The maximum permissible deflection is limited by the maximum deflection angle of 5’. Exceeding this value without sup-port will have a negative effect on the unit’s service life.
If increased demands are made on sys-tem accuracy we recommend supporting the linear modules along its entire length.
The following diagrams apply for:- firm clamping (40–50 mm per side)- 3–4 screws per side- solid base
Mounting position: horizontal
LINEar ModuLES wITH baLL SCrEw drIVE
Permissible deflection
LM3…R...N resp. LM3...R…L/R
LM4…R...N resp. LM4...R…L/R
LM5…R...N resp. LM5...R…L/R
21www.linetech.ch
500 1000 1500 2000 50002500 3000 3500 4000 4500 5500 6000 6500 7000 7500
1
2
3
0.5
1.5
2.5
fmax [mm]
LM [mm]
8000
2500
N20
00 N 1500
N10
00 N 5
00 N
250
N
0 N
fmax
500 1000 1500 2000 50002500 3000 3500 4000 4500 5500 6000 6500 7000 7500
1
2
3
0.5
1.5
2.5
fmax [mm]
LM [mm]
8000
fmax
2500
N20
00 N
1500
N 1000
N
500
N 250
N
0 N
500 1000 1500 2000 50002500 3000 3500 4000 4500 5500 6000 6500 7000 7500
1
2
3
0.5
1.5
2.5
fmax [mm]
LM [mm]
8000
fmax
2500
N20
00 N
1500
N 100
0 N 50
0 N 25
0 N
0 N
LM / 2 LM
f max
F
LM
Permissible deflection
LM3…Z...N resp. LM3…Z...L/R
LM4…Z...N resp. LM4…Z...L/R
LM5…Z...N resp. LM5…Z...L/R
Permissible deflectionwith toothed belt drive
Mounting position: horizontal
LINEar ModuLES wITH TooTHEd bELT drIVE
22 LINE TECH – SWISS MADE LINEAR TECHNOLOGY
B
H
B
H
LM
LINEar ModuLES wITH baLL SCrEw drIVE
Designation system
Design
LM = linear module with linear guide
Linear module (designation example)
Size
3 = size 65 mm4 = size 80 mm5 = size 110 mm
Stroke absolut [mm]
Protective covering
B = with steel strip *** N = without protective strip 1)
Drive
R = rolled ball screw ***N = without drive
Stroke per revolution [mm]
005 / 010 / 016 = size 3; ball screw with a pitch of 5, 10 or 16 mm005 / 020 = size 4; ball screw with a pitch of 5 or 20 mm005 / 010 / 032 = size 5; ball screw with a pitch of 5, 10 or 32 mm... = other pitch 1)
Configuration
2 = 2 runner blocks (1 carriage) ***… = special execution 1)
Limit switches
0 = without limit switch1 = 2 limit switches, reference point at front (drive side)2 = 2 limit switches, reference point at rear (opposite drive side)3 = 2 limit switches + additional reference switch at front (drive side)4 = 2 limit switches + additional reference switch at rear (opposite drive side)
* seen from motor opposite side towards motor** available for lateral motor mounting only*** standard version1) on request2) new designation system from 01.01.2015
SizeLM...N
B x H [mm]LM...L/R
B x H [mm]
3 65 x 85 98 x 94
4 80 x 100 117 x 109
5 110 x 129 155 x 141
LM 4 . 2 . 0500 B R 005 . 1 . 01 . 0 N - S 7 R L N N
23www.linetech.ch
LM
583... = drawing type
Assembly stage
00 = without drive 00 01 0201 = free spindle end ***02 = with coupling and intermediate plate03 = with crank and clamp04 = set up for lateral motor mounting right * 03 04 0505 = set up for lateral motor mounting left *06 = set up for lateral motor mounting top07 = set up for lateral motor mounting bottom08 = with crank, clamp and lateral millimetre scale 06 07 08
Reduction 2)
0 = without reduction (1:1) ***1 = reduction 1:1.5 **2 = reduction 1:2 **(3 = reduction 1:2.5) **
Motor mounting
N = without motor mounting ***F = mounting plate for standard motorS = mounting plate for special motor
Material protective strip
S = steel strip ***R = stainless steel stripN = without protective strip
Preload ball screw drive (BSD)
R = BSD with reduced play ***V = BSD preloadedN = without drive
Mounting position of limit switches / connector box
N = without limit switches / connector box ***L = limit switches / connector box mounting left *R = limit switches / connector box mounting right *
Connector box
N = without connector box (loose cable L = 2.0 m) ***S = with connector box
Lateral support rail
N = without lateral support rail ***L = lateral support rail leftR = lateral support rail right
Tolerance class ball screw drive (BSD)
7 = Tolerance class BSD: T7 (52 µm / 300 mm) ***N = without drive
LM 4 . 2 . 0500 B R 005 . 1 . 01 . 0 N - S 7 R L N N5 8 3 _ _ _
24 LINE TECH – SWISS MADE LINEAR TECHNOLOGY
LM
LINEar ModuLES wITH baLL SCrEw drIVE
Information for selection » Motor mounting preparation
Motor fitting preparation – assembly stages with ball screw drive
LINE TECH linear modules with ball screw drive can be supplied with different motor mount preparations.Refer to pages 52 and 53 for dimensions.
Assembly stage 02With coupling and intermediate plate
Assembly stage 05Belt drive housing for lateral motor mounting left
Assembly stage 07Belt drive housing for lateral motor mounting bottom
Assembly stage 04Belt drive housing for lateral motor mounting right
Assembly stage 06Belt drive housing for lateral motor mounting top
Assembly stage 01Free spindle end
25www.linetech.ch
LM
NoTES
26 LINE TECH – SWISS MADE LINEAR TECHNOLOGY
28 52,5 8511
25
85
190
L
3070
65
6
32
ø10
h6
ø38
h6
43
246
33
5361
LM
84
4xM6x124x
M4x8
LM
Stroke
LINEar ModuLE LM3…br…N
with ball screw drive, with steel strip
Nominal size Dimensions
Designation L[mm]
LM[mm]
Length ball screw[mm]
Length steel strip[mm]
Weight[kg]
LM3...BR…N Stroke + 360 L – 58 L + 22 L – 22 4.60 kg + 0.65 kg/100 mm stroke
CAD data is available from www.linetech.ch
27www.linetech.ch
28
25
94
190
33
98
32,546
18015 50 50 50
40 50 50
30.5
46
42,5
46
5
20 50 50 50
6
32
ø10
h6
ø38
h6
43
30
70
246
65
14xM5x9
LLM
53618xM5x9 4x
M6x12
84
LM
LINEar ModuLE LM3…br…L/r
with ball screw drive and lateral support rail left/right, with steel strip
Nominal size Dimensions
Designation L[mm]
LM[mm]
Length ball screw[mm]
Length steel strip[mm]
Weight[kg]
LM3...BR…L/R Stroke + 360 L – 58 L + 22 L – 22 6.11 kg + 0.78 kg/100 mm stroke
Stroke
CAD data is available from www.linetech.ch
LM3…BR…L LM3…BR…R
28 LINE TECH – SWISS MADE LINEAR TECHNOLOGY
87.5 85 7
100
20
32.5 6565 65
260
60
40
L
ø12
h6
ø46
h6
5
36
30
8070
54
344
42
8xM6x11
LM
4xM4x8
4868
4xM6x12
97.5
LM
Stroke
LINEar ModuE LM4…br…N
with ball screw drive, with steel strip
Nominal size Dimensions
Designation L[mm]
LM[mm]
Length ball screw[mm]
Length steel strip[mm]
Weight[kg]
LM4...BR…N Stroke + 460 L – 60 L + 30 L – 22 7.8 kg + 0.95 kg/100 mm stroke
CAD data is available from www.linetech.ch
29www.linetech.ch
6565
109
220
20
6565
35.5
40
L
ø12
h6
ø46
h6
5
36
30
8070
54
3960
65
60
4760
65 65 65
117
32.5
344
6542
32.5
14xM6x9
4868
4xM6x12
8xM6x9
LM
97.5
260
LM
LINEarModuL LM4…br…L/r
with ball screw drive and lateral support rail left/right, with steel strip
Nominal size Dimensions
Designation L[mm]
LM[mm]
Length ball screw[mm]
Length steel strip[mm]
Weight[kg]
LM4...BR…L/R Stroke + 460 L – 60 L + 30 L – 22 10.46 kg + 1.18 kg/100 mm stroke
Stroke
CAD data is available from www.linetech.ch
LM4…BR…L LM4…BR…R
30 LINE TECH – SWISS MADE LINEAR TECHNOLOGY
112.5 859
25
42.5 75 75 75
310
85
129
394
42
86
7386
110
ø22
h6
ø85
f8
50
L55
13
8xM8x18
4xM10x20
LM
5378
4xM4x8
128
LM
LINEar ModuLE LM5…br…N
with ball screw drive, with steel strip
Nominal size Dimensions
Designation L[mm]
LM[mm]
Length ball screw[mm]
Length steel strip[mm]
Weight[kg]
LM5...BR…N Stroke + 525 L – 75 L + 50 L – 44 16.8 kg + 1.9 kg/100 mm stroke
Stroke
CAD data is available from www.linetech.ch
31www.linetech.ch
42.5 75
25
80 75 75
141
394
42
86
7386
110
ø22
h6
ø85
f8
50
L55
13
42.5 75 75 75
75 75
43.5
85
3985
57.5
85
155
14xM8x12
5378
8xM8x12
LM4xM10x20
128
305
310
LM
LINEar ModuLE LM5…br…L/r
with ball screw drive and lateral support rail left/right, with steel strip
Nominal size Dimensions
Designation L[mm]
LM[mm]
Length ball screw[mm]
Length steel strip[mm]
Weight[kg]
LM5...BR…L/R Stroke + 525 L – 75 L + 50 L – 44 21.75 kg + 2.21 kg/100 mm stroke
Stroke
CAD data is available from www.linetech.ch
LM5…BR…L LM5…BR…R
32 LINE TECH – SWISS MADE LINEAR TECHNOLOGY
B
H
B
H
LM
LINEarModuLE wITH TooTHEd bELT drIVE
Designation system
Design
LM = linear module with linear guide
Linear module (designation example)
Size
3 = size 65 mm4 = size 80 mm5 = size 110 mm
Stroke absolut [mm
Protective covering
B = with steel strip N = without protective strip ***
Drive
Z = toothed belt drive ***N = without drive
Stroke per revolution [mm]
155 = size 3; toothed belt drive with 155 mm stroke per revolution205 = size 4; toothed belt drive with 205 mm stroke per revolution296 = size 5; toothed belt drive with 296 mm stroke per revolution… = other stroke per revolution 1)
Configuration
2 = 2 runner blocks (1 carriage) ***… = special execution 1)
Limit switches
0 = without limit switch1 = 2 limit switches, reference point at front (drive side)2 = 2 limit switches, reference point at rear (opposite drive side)3 = 2 limit switches + additional reference switch at front (drive side)4 = 2 limit switches + additional reference switch at rear (opposite drive side)
* seen from motor opposite side towards motor** available for lateral motor mounting only*** standard version1) on request2) details see gear mounting, pages 55/56
SizeLM...N
B x H [mm]LM...L/R
B x H [mm]
3 65 x 85 98 x 94
4 80 x 100 117 x 109
5 110 x 129 155 x 141
LM 4 . 2 . 0500 N Z 205 . 1 . 12 . 0 N - N N N L N N
33www.linetech.ch
LM
Assembly stage
00 = without drive
11 = free shaft end right *12 = free shaft end left *13 = shaft end right with coupling and intermediate plate *14 = shaft end left with coupling and intermediate plate *17 = free shaft ends on both sides (passing shaft)18 = shaft end on both sides, with coupling and intermediate flange right *19 = shaft end on both sides, with coupling and intermediate flange left *25 = shaft end right with gear mounting *26 = shaft end left with gear mounting * 27 = shaft end on both sides, right with gear mounting *28 = shaft end on both sides, left with gear mounting *
583... = drawing type
Reduction
0 = without reduction ***X = i = __________ (in conjunction with gear type FH or AE) 2)
Motor mounting
N = without motor mounting ***F = mounting plate for standard motorS = mounting plate for special motor
Material protective strip
N = without protective strip ***S = steel stripR = stainless steel strip
Gear box mounting
N = without gear *** F = back / bottom K = front / bottomD = top / rear G = rear / top L = bottom / frontE = top / front H = front / top M = bottom / back
Mounting position of limit switches / connector box
N = without limit switches / connector box ***L = limit switches / connector box mounting left *R = limit switches / connector box mounting right *
Connector box
N = without connector box (loose cable L = 2.0 m) ***S = with connector box
Lateral support rail
N = without lateral support railL = lateral support rail leftR = lateral support rail right
Drive shaft
N = standard shaft ***S = shaft for standard worm gear FH 2)
H = shaft for high-performance servo worm gear AE 2)
O = without drive shaft
00 11 12
13 14 17
18 19 25
26 27 28
LM 4 . 2 . 0500 N Z 205 . 1 . 12 . 0 N - N N N L N N5 8 3 _ _ _
34 LINE TECH – SWISS MADE LINEAR TECHNOLOGY
LM
LINEar ModuLES wITH TooTHEd bELT drIVE
Information for selection » Motor mounting preparation (1/3)
Motor mounting preparation – assembly stages with toothed belt drive
LINE TECH linear modules with toothed belt drive can be supplied in different assembly stages as preparation for motor mounting. Refer to pages 54 to 56 for dimensions.
Assembly stage 12Free shaft end left*
Assembly stage 14Shaft end left* with coupling and intermediate flange
Assembly stage 17Free shaft ends on both sides
Assembly stage 13Shaft end right* with coupling and intermediate flange
Assembly stage 00Without drive
Assembly stage 11Free shaft end right*
* seen from motor opposite side towards motor
35www.linetech.ch
LM
LINEar ModuLES wITH TooTHEd bELT drIVE
Information for selection » Motor mounting preparation (2/3)
Assembly stage 19Shaft ends on both sides, left* with coupling and intermediate flange
Assembly stage 26Shaft end left* with gear mounting plate
Assembly stage 28Shaft ends on both sides, left* with gear mounting plate
Assembly stage 25Shaft end right* with gear mounting plate
Assembly stage 27Shaft ends on both sides, right* with gear mounting plate
Assembly stage 18Shaft ends on both sides, right* with coupling and intermediate flange
* seen from motor opposite side towards motor
36 LINE TECH – SWISS MADE LINEAR TECHNOLOGY
LM
* seen from motor opposite side towards motor
LINEar ModuLES wITH TooTHEd bELT drIVE
Information for selection » Motor mounting preparation (3/3)
Motor mounting preparation – mounting options (alignment) of worm drives
For assembly stages 25 to 28 (see page 35), the gear mounting plate can be pre-mounted differently depending on gear mounting and motor alignment required:
Gear box mounting fGear towards back* and bottom
Gear box mounting GGear towards back* and top
Gear box mounting HGear towards front* and top
Gear box mounting KGear towards front* and bottom
Gear box mounting DGear towards back* and top
Gear box mounting EGear towards front* and top
Gear box mounting LGear towards front* and bottom
Gear box mounting MGear towards back* and bottom
37www.linetech.ch
LM
NoTES
38 LINE TECH – SWISS MADE LINEAR TECHNOLOGY
52.5 85
8
206
11
L
95 95
26
40
43
20 50 5050
190
46
33
85
65
ø15
h7
33
ø38
H7
x 1.
5
LM
114.5114.5
4xM4x8
4xM5x8
8xM5
65
LM
LINEar ModuLES LM3…NZ…N
with toothed belt drive, without protective strip
Nominal size Dimensions
Designation L[mm]
LM[mm]
Belt length[mm]
Weight[kg]
LM3...NZ…N Stroke + 435 L – 190 2 x Stroke + 730 4.50 kg + 0.60 kg/100 mm Stroke
Stroke
CAD data is available from www.linetech.ch
39www.linetech.ch
52.5 85
11
L
95 95
26
40
43
20 50 5050
190
46
33
8565
ø15
h7
33
246
28
4xM5x8
ø38
H7
x 1.
5
8xM5
114.5114.5
4xM4x8
LM
65
LM
LINEar ModuLES LM3…bZ…N
with toothed belt drive, with steel strip
Nominal size Dimensions
Designation L[mm]
LM[mm]
Belt length[mm]
Length steel strip[mm]
Weight[kg]
LM3...BZ…N Stroke + 475 L – 190 2 x Stroke + 810 L – 10 4.80 kg + 0.61 kg/100 mm Stroke
Stroke
CAD data is available from www.linetech.ch
40 LINE TECH – SWISS MADE LINEAR TECHNOLOGY
20 508
206
L
95 95
26
40
43
20 50 5050
46
33
94
65
50 50
32.5
46
98
45 50 50
42.5
30.5
46
ø38
H7
x 1.
5
14x M5x9
114.5
8xM5x9
LM
114.5
4xM5x8
A
ø15 h7
33
A
65
180
190
LM
LINEar ModuLES LM3…NZ…L/r
with toothed belt drive and lateral support rail left/right, without protective strip
Nominal size Dimensions
Designation L[mm]
LM[mm]
Belt length[mm]
Weight[kg]
LM3...NZ…L/R Stroke + 435 L – 190 2 x Stroke + 730 5.94 kg + 0.73 kg/100 mm Stroke
Stroke
CAD data is available from www.linetech.ch
LM3…NZ…L LM3…NZ…R
41www.linetech.ch
20 50
L
95 95
26
40
43
20 50 5050
46
33
94
65
50 50
32.5
46
98
45 50 50
42.5
30.5
46
246
28
ø38
H7
x 1.
5
14x M5x9
8xM5x9
4xM5x8
114.5114.5
LM
A
ø15 h7
33
A
65
180
190
LM
LINEar ModuLES LM3…bZ…N
with toothed belt drive and lateral support rail left/right, with steel strip
Nominal size Dimensions
Designation L[mm]
LM[mm]
Belt length[mm]
Length steel strip[mm]
Weight[kg]
LM3...BZ…L/R Stroke + 475 L – 190 2 x Stroke + 810 L – 10 6.30 kg + 0.74 kg/100 mm Stroke
-Stroke
CAD data is available from www.linetech.ch
LM3…BZ…L LM3…BZ…R
42 LINE TECH – SWISS MADE LINEAR TECHNOLOGY
8 87.5 85
52
88
50
113 113
L
276
260
32.5 65 65 65
60
80 3510
0
ø19
h7
41
7ø64
H7
x 1.
5
8xM6x11
4x M6x
12
132132
4xM4x8
LM
80
LM
LINEar ModuLE LM4…NZ…N
with toothed belt drive, without protective strip
Nominal size Dimensions
Designation L[mm]
LM[mm]
Belt length[mm]
Weight[kg]
LM4...NZ…N Stroke + 540 L – 226 2 x Stroke + 900 8.40 kg + 0.93 kg/100 mm Stroke
Stroke
CAD data is available from www.linetech.ch
43www.linetech.ch
87.5 8552
88
50
113 113
L
260
32.5 65 65 65
60
80 3510
0
ø19
h7
41
7
42
344
ø64
H7
x 1.
5
8xM6x11
4x M6x
12
132132
4xM4x8
LM
80
LM
LINEar ModuLE LM4…bZ…N
with toothed belt drive, with steel strip
Nominal size Dimensions
Designation L[mm]
LM[mm]
Belt length[mm]
Length steel strip[mm]
Weight[kg]
LM4...BZ…N Stroke + 608 L – 226 2 x Stroke + 1040 L – 12 9.10 kg + 0.95 kg/100 mm Stroke
Stroke
CAD data is available from www.linetech.ch
44 LINE TECH – SWISS MADE LINEAR TECHNOLOGY
8 32.5 6552
88
50
113 113
L
276
32.5 65 65 65
60
80
109
41
39
65
60
65
35.5
4760
65 65 65
260
117
ø64
H7
x 1.
5
14xM6x9
4x M6x
12
132132
8xM6x9
LM80
A
ø19 h7
35
A
220
LM
LINEar ModuLE LM4…NZ…L/r
with toothed belt drive and lateral support rail left/right, without protective strip
Nominal size Dimensions
Designation L[mm]
LM[mm]
Belt length[mm]
Weight[kg]
LM4...NZ…L/R Stroke + 540 L – 226 2 x Stroke + 900 10.86 kg + 1.16 kg/100 mm Stroke
Stroke
CAD data is available from www.linetech.ch
LM4…NZ…L LM4…NZ…R
45www.linetech.ch
32.5 65
52
88
50
113 113
L
32.5 65 65 65
60
80
109
41
39
65
60
65
35.5
4760
65 65 65
260
117344
42
ø64
H7
x 1.
5
14xM6x9
4x M6x
12
132132
8xM6x9
LM
A
80
35
A
ø19 h7
220
LM
LINEar ModuLE LM4…bZ…L/r
with toothed belt drive and lateral support rail left/right, with steel strip
Nominal size Dimensions
Designation L[mm]
LM[mm]
Belt length[mm]
Length steel strip[mm]
Weight[kg]
LM4...BZ…L/R Stroke + 608 L – 226 2 x Stroke + 1040 L – 12 11.72 kg + 1.18 kg/100 mm Stroke
Stroke
CAD data is available from www.linetech.ch
LM4…BZ…L LM4…BZ…R
46 LINE TECH – SWISS MADE LINEAR TECHNOLOGY
305
75 75 7540
85
L
150 150
88
8
321
110 85
9
50
69.5
ø19
h7
55
110 4412
9
ø64
H7
x 2.
5
8xM8x18
4x M6x
12
174.5174.5
4xM4x8
LM
110
LM
LINEar ModuLE LM5…NZ…N
with toothed belt drive, without protective strip
Nominal size Dimensions
Designation L[mm]
LM[mm]
Belt length[mm]
Weight[kg]
LM5...NZ…N Stroke + 670 L – 300 2 x Stroke + 1144 18.60 kg + 1.48 kg/100 mm Stroke
Stroke
CAD data is available from www.linetech.ch
47www.linetech.ch
305
75 75 7540
85
L
150 150
88
110 85
9
50
69.5
ø19
h7
55
110 4412
9
42
389
ø64
H7
x 2.
5
8xM8x18
4x M6x
12
168.5168.5
4xM4x8
LM
110
LM
LINEar ModuLE LM5…bZ…N
with toothed belt drive, with steel strip
Nominal size Dimensions
Designation L[mm]
LM[mm]
Belt length[mm]
Length steel strip[mm]
Weight[kg]
LM5...BZ…N Stroke + 726 L – 300 2 x Stroke + 1256 L – 14 19.50 kg + 1.50 kg/100 mm Stroke
Stroke
CAD data is available from www.linetech.ch
48 LINE TECH – SWISS MADE LINEAR TECHNOLOGY
77.5
75 75 7540
85
L
150 150
88
8
321
40 75
43.5
50
69.5
55
110
141
85
75 75155
75 75
57.5
3985
ø64
H7
x 2.
5
14x M8x12
4x M6x
12
174.5174.5
8xM8x12
LM11
0
A
44
A
ø19 h7
305
305
LM
LINEar ModuLE LM5…NZ…L/r
with toothed belt drive and lateral support rail left/right, without protective strip
Nominal size Dimensions
Designation L[mm]
LM[mm]
Belt length[mm]
Weight[kg]
LM5...NZ…L/R Stroke + 670 L – 300 2 x Stroke + 1144 23.31 kg + 1.79 kg/100 mm Stroke
Stroke
CAD data is available from www.linetech.ch
LM5…NZ…L LM5…NZ…R
49www.linetech.ch
77.5
75 75 7540
85
L
150 150
88
40 75 43.5
50
69.5
55
110
141
85
75 75155
75 75
57.5
3985
42
389
14x M8x12
ø64
H7
x 2.
5
168.5168.5
8xM8x12
LM
4x M6x
12
110
A
44
A
ø19 h7
305
305
LM
LINEar ModuLE LM5…bZ…L/r
with toothed belt drive and lateral support rail left/right, with steel strip
Nominal size Dimensions
Designation L[mm]
LM[mm]
Belt length[mm]
Length steel strip[mm]
Weight[kg]
LM5...BZ…L/R Stroke + 726 L – 300 2 x Stroke + 1256 L – 14 24.38 kg + 1.81 kg/100 mm Stroke
Stroke
CAD data is available from www.linetech.ch
LM5…BZ…L LM5…BZ…R
50 LINE TECH – SWISS MADE LINEAR TECHNOLOGY
LR
LR
0.5...0.8 mm
16
30
41.5
x
38
15
LM
LINEar ModuLES
Limit switch mounting
Limit switches
The limit switches are used in conjunc-tion with a control unit to limit the stroke (prevent overrunning of the carriage) and to define the reference position.
LINE TECH employs the following stand-ard inductive limit switches:
– PNP openers (PNP-NC) Supply: 10...30 V DC Current consumption off-load: < 10 mA Load: max. 200 mA
On request the following non standard limit switches are available:
– PNP make type (PNP-NO)– NPN break type (NPN-NC)– NPN make type (NPN-NO)– Reed switches– mechanical switches
Note: At the factory the plus and minus limit switches are preset to a nominal stroke of 0 to +5 mm.
fitting position of limit switches
The following diagrams show the mount-ing position of the limit switches. The reference position can be allocated either to the plus (+) or to the minus (-) limit switch.
Special applications often require a sepa-rate reference point switch to be mount-ed between the positive and negative limit switches. The limit switch closest to the motor mounting (limit switch control-ler interface) is known as the forward limit switch.
Note: If a lateral support rail is selected (type LM…L/R), the limit switches can only be fitted on the opposite side.
Limit switch mounting
Mounting left
Mounting right
Dimensions / switch gap:
Position of reference switch (LR)
Front reference switch (motor side)
LR = 20 mm Rear reference switch (opposite motor side)
Limit switches / reference switch mounting overview
Limit switch resolution
Connector box
Plus limit switch (+)
Reference switch
Minus limit switch (–)
Size x [mm]
LM3 55
LM4 51
LM5 59
51www.linetech.ch
+ V
DC
0 V
(GN
D)
+ V
DC+ V
DC
0 V
(GN
D)
0 V
(GN
D)
1
4
2
5
3
+ V
DC
0 V
(GN
D)
+ V
DC
0 V
(GN
D)
1
4
2
5
3
LM
LINEar ModuLES
Limit switch with/without connector box
Plug connector
The connector pin assignment when using a connector box is shown in the diagram on the right. The individual pins are assigned as follows:
Pin 1 Minus (–) direction (load)Pin 2 0 V (GND)Pin 3 Plus (–) direction (load)Pin 4 +10...30 V (DC)Pin 5 Reference (load)
Colour code key for the diagrams:
Load = black+V DC = brown0 V (GND) = blue
– Direction + Direction
– Direction + DirectionReference
PNPOpener
PNPOpener
PNPOpener
PNPOpener
PNPOpener
Plug SFV50acc. to IEC 60130-9
Plug SFV50acc. to IEC 60130-9
Reference point bridge
Reference point in minus (–) directionFont (drive side)Bridge pin 1–5
Reference point in plus (+) directionRear (opposite drive side)Bridge pin 3–5
Load
Load
Load
Load
Load
Plug connector with reference point bridge
Plug connector with additional reference switch
Limit switch preparation
Limit switches are supplied as standard without connector box with 2 metre long cables (order code N); a connector box with completed cabling is available as an option (order code S).
Limit switch mating connectors and cables are not included in the delivery but can be ordered ready-made from LINE TECH.
Standard: without connector box (N), with loose connector cables (L = 2 m)
Optional: with connector box (S)
52 LINE TECH – SWISS MADE LINEAR TECHNOLOGY
øDK
øD
f1 f1
L
E
ød
LW E LS
LF
LWøDM
LZ
B
ødW
øZ
LK
F
LM
LINEar ModuLES wITH baLL SCrEw drIVE
Dimensions for motor mounting; straight fit
* Flange including coupling
Nomi-nal size
Dimensions Coupling
LF ±2[mm]
LS[mm]
Weight *[kg]
if LW > f1
LM3…
LS + E + LW
32 0.500 Size 14
LM3... 32 0.580 Size 19
LM4... 36 0.640 Size 19
LM5... 55 1.800 Size 24
Dimensions [mm]
Drivetorque [Nm]
Size L ø D ø d f1 E ø DK TN Tmax
14 35 30 ≤ 16 11 13 32.2 6.3 25
19 66 40 ≤ 20 25 16 43 17 34
24 78 55 ≤ 28 30 18 57 40 120
Straight motor mounting
Length of straight motor mounting Coupling
Motor
Motor plate
Coupling
Intermediate flange
** The following dimensions
ø DM _____________ [mm] LW _____________ [mm]
B _____________ [mm] ø dW _____________ [mm]
F _____________ [mm] LZ _____________ [mm]
LK _____________ [mm] ø Z _____________ [mm]
are required to determine the motor mounting.
Motor dimensions **
53www.linetech.ch
G
E K
LG
F
F / 2 H
LM
LINEar ModuLES wITH baLL SCrEw drIVE
Dimensions for motor mounting; lateral fit
Lateral motor mounting
Motor
Toothed belt
LM pinionNo. of teeth = zLM
Belt drive housing
Motor pinionNo. of teeth = zM
i = zM : zLM
Dimensions for lateral motor mounting
Nomi-nal size
Dimensions [mm] No. of teeth
Max. Belt length
Weight
i E F G* H K LG zM zLM ø dW [mm] [kg]
LM3…
1:1 130…135 (132.5) 32 32 ø19 425 1.600
1:1.5 131…139 (135) 100 43 43 46 247 32 48 ø19 475 1.800
1:2 131.5…135.5 (133.5) 24 48 ø12 450 1.700
LM4...
1:1 130...135 (132.5)
100 43 54 46 247
32 32 ø19 425 1.600
1:1.5 131...139 (135) 32 48 ø19 475 1.800
1:2 131.5...135.5 (133.5) 24 48 ø12 450 1.700
LM5...
1:1 163.5...171.5 (167.5)
120
48 48 ø25 575 2.910
1:1.5 170.5...178.5 (174.5) 60 73 65 300 32 48 ø19 550 2.800
1:2 168.5...176.5 (172.5) 27 54 ø14 550 2.900
Carriage
54 LINE TECH – SWISS MADE LINEAR TECHNOLOGY
LWøDM
LZ
B
ødW
øZ
LK
F
øDK
øDf1 f1
L
E
ød
L SE
L W
L F
LM
** The following dimensions
ø DM _____________ [mm] LW _____________ [mm]
B _____________ [mm] ø dW _____________ [mm]
F _____________ [mm] LZ _____________ [mm]
LK _____________ [mm] ø Z _____________ [mm]
are required to determine the motor mounting.
Motor dimensions **
Straight motor mounting
Length of motor Couplingmounting
MotorMotor plate
Coupling
Intermediate flange
Nom.size
Dimensions CouplingLF ±2[mm]
LS[mm]
Weight *[kg]
if LW > f1
LM3…
LS + E + LW
33 0.780 Size 19
LM4... 35 1.150 Size 19
LM4... 35 1.250 Size 24
LM5... 44 1.100 Size 19
LM5... 44 1.400 Size 24
Dimensions [mm] Drivetorque [Nm]
Size L ø D ø d f1 E ø DK TN Tmax
19 66 40 ≤ 20 25 16 43 17 34
24 78 55 ≤ 28 30 18 57 40 120
LINEar ModuLES wITH TooTHEd bELT drIVE
Dimensions for motor mounting; straight fit
* Flange including coupling
55www.linetech.ch
LM
LINEar ModuLES wITH TooTHEd bELT drIVE
Dimensions for motor fitting; gear mounting (1/2)
Feather key Outside tensioning set
Motor plate Motor plate
Gear mounting plate Gear mounting plate
Gear Gear
Coupling Coupling
Standard worm drive HPG…-A7… (fH) 1)
High-performance servo worm drive HPG…-A1… / HPG…-A2… (AE) 1)
1) Possible gear reductions: 1: 2 / 3 / 4 / 5 / 6 / 8 / 10 / 13.33 / 16 / 24 / 30 / 47 / 60
56 LINE TECH – SWISS MADE LINEAR TECHNOLOGY
A A
x D
C
= =
B
= =
B
A A
C
D x
A A
= = B
C x D
= =
B
A A
x C
D
E F
E +
F
E /
2
E /
2 E G
F
E +
F +
G
LM
LINEar ModuLES wITH TooTHEd bELT drIVE
Dimensions for motor fitting; gear mounting (2/2)
Nomi-nal size
Gear box type Casing dimensions [mm] Weight Gear
x LW A B C D E F G* [kg] [kg]
LM3...HPG…-A7… (fH) 1) 30 20...33 85 90 100 40 65 12 – 0.500 1.900
HPG…-A1 / 2… (AE) 1) 30 20...33 85 90 100 40 65 12 18.5 0.500 2.020
LM4...
HPG…-A7… (fH) 1)45 20...33 98
120 135 50 85 20 – 1.200 3.900
45 33...43 108 4.000
HPG…-A1 / 2… (AE) 1)45 20...33 98
120 135 50 85 20 23.5 1.200 4.100
45 33...43 108 4.200
HPG…-A7… (fH) 1)
60 25...40 120
150 180 65 110 25 – 2.200
8.500
60 40...50 130 8.650
60 50...65 145 8.700
HPG…-A1 / 2… (AE) 1)
60 25...40 120
150 180 65 110 25 25.0 2.200
8.800
60 40...50 130 8.850
60 50...65 145 8.900
LM5...
HPG…-A7… (fH) 1)90 40...62 172
200 250 100 150 25 – 3.80022.800
90 62...82 192 22.900
HPG…-A1 / 2… (AE) 1)90 40...62 172
200 250 100 150 25 30.0 3.80023.700
90 62...82 192 23.800
Dimensions for gear mounting
Assembly direction: D + M Assembly direction: E + L Assembly direction: F + K Assembly direction: G + H
Standard worm drive HPG…-A7… (FH) 1)
High-performance servo worm drive HPG…-A1… / HPG…-A2… (AE) 1)
1) Possible gear reductions: 1: 2 / 3 / 4 / 5 / 6 / 8 / 10 / 13.33 / 16 / 24 / 30 / 47 / 60
57www.linetech.ch
LM
NoTES
58 LINE TECH – SWISS MADE LINEAR TECHNOLOGY
B C
AH
B C C C
A
H
K
J G F
D
E
A±0.1 C
B
C1)
A±0.1
B
12
M6LM
Clamps
Recommended number of clamps:4 per metre and side Type I
Type II
LINEar ModuLES
Attachment accessories; clamps
Mounting options
The linear modules are secured with clamps or sliding blocks.
Caution: Only attach and support the linear modules on the base profile, not on the end plates.
Nomi-nal size
Dimensions [mm]
A B C
LM3… 76.8 88.8 40
LM4... 94.0 108.0 531)
LM5... 132.0 150.0 85
Nominal size
Dimensions [mm] Weight Art. No.
Type A B C D E F G* H J K [kg]
LM3…I
80 10…
19.0 12.0 16 11.9 6 ø11 ø 6.5…… …………
II 20 0.118 P-54376/1
LM4...I
80 1060
22.0 15.0 20 14.0 7 ø11 ø 6.50.195 M-40023/1
II ... …… …………
LM5...I
108 1970
25.7 16.7 28 20.0 9 ø 15 ø 9.00.412 M-50158/1
II ... …… …………
1) possible for size LM4 with planning by LINE TECH during production
LM4...LM3.../LM5...
59www.linetech.ch
a
LM
Attachment accessories; sliding blocks
Sliding blocks
Sliding blocks having the relevant groove width can be used to mount add-on parts to the base profile.
Sliding block types NS5, NS6 and NS8 can be used in line with the groove width (see profile cross-sections, pages 9 to 11).Sliding blocks are available from LINE TECH. Size, material and connection thread as per the following order system (e.g. NS6 St M5) must be defined as the order number. The available types are listed opposite.
Order designation for sliding blocks
Examples: NS6 St M5
Dimensions [mm] Material
Groove width a (thread)
5 M3 / M4 / M5 steel / stainless steel
6 M4 / M5 / M6 steel / stainless steel
8 M4 / M5 / M6 / M8 steel / stainless steel
Material
St = steelInox = stainless steel
Thread size (dim. “a”)
M3 / M4 / M5 / M6 / M8
Sliding block NS
Groove width
5 68
LINEar ModuLES
NS 6 St M5
60 LINE TECH – SWISS MADE LINEAR TECHNOLOGY
LM
LINEar ModuLES
Grease points (1/2)
Ball screw 1) 3)
Runner blocks 1) 3)
Runner blocks 1) 3)
Ball screw 1)
Ball screw 1) 3)
Runner blocks 2) Runner blocks 2)
Runner blocks 1)
Runner blocks 1) 3)
Runner blocks 1)
Ball screw 1)
Runner blocks 2)
Runner blocks 1)
Runner blocks 2)
Runner blocks 1)
Runner blocks 1) 3)
LM3..R..N LM3..Z..N
LM3..R..L/R LM3..Z..L/R
LM4..R..N LM4..Z..N
LM4..R..L/R LM4..Z..L/R
61www.linetech.ch
LM
Grease pointsDifferent lubricating nipples are on the linear module carriages: 1) Lubricating nipple to DIN 34052) Lubricating nipple to DIN 714123) Lubrication either on left or right sideGreasing positions are not dependent on stroke.
Standard greaseLINE TECH recommends the following grease for lubrication:Microlube GBU Y 131
Grease gun
Art. no.: ZPE.FETTPRESSE-03
LINEar ModuLES
Grease points (2/2)
Ball screw 1)
Runner blocks 2)
Runner blocks 1)
Ball screw 1) 3)
Runner blocks 1) 3)
Runner blocks 2)
Runner blocks 1)
Runner blocks 1) 3)
LM5..R..N LM5..Z..N
LM5..R..L/R LM5..Z..L/R
www.linetech.ch
®
LINE TECH AGEuropastrasse 198152 GlattbruggSwitzerland
Phone +41 43 211 68 68Fax +41 43 211 68 69
© LINE TECH AG
The contents of this publication are protected by
copyright held by the publisher and may not be
reproduced in whole or in part unless permission is
granted. Every care has been taken to ensure the
accuracy of the information contained herein but
no liability can be accepted for any loss or damage,
whether direct, indirect or consequential, resulting
from or in connection with the use of the information
contained herein. This catalogue supersedes previ-
ous catalogues in which information differs from that
contained herein. Information is subject to change as
required by technological advancements.
Edition: 11-2015 E
Your LINE TECH representative: