Linear Open Frame DC Power SuppliesSilver Line Instruction Manual
Model: SLD-12-1010-12T
FeaturesInput AC Connections
Mechanical Dimensions: inches (mm)
For use at: Connect Apply AC to: Primary Fuse100 VAC 1-3, 2-4 1 & 5 0.63A/125V
120 VAC* 1-3, 2-4 1 & 4 0.63A/125V
220 VAC 2-3 1 & 5 0.315A/250V
230 VAC 2-3 1 & 4 0.315A/250V
240 VAC 2-3 1 & 4 0.315A/250V
Case H1
General Specifications
Voltage/Current RatingsModel Number Output 1 Output 2
SLD-12-1010-12T +12V/1.0A or +15V/0.8A -12V/1.0A or -15V/0.8A
*Outputs are tied common
Operating Temperature Range 0 to +50oC (Derate to 40% at +70oC)
Temperature Coefficient (Typical) +/- 0.01% / oC
Stability Within +/- 0.05% (For 24 hours after warm-up)
Vibration Per MIL-STD-810C, Method 514
Shock Per MIL-STD-810C, Method 516
EMI/RFI Linear power supplies have inherently low conducted and radiated noise levels. For most system applications, these power supplies will meet the requirements of FCC Class “B” and VDE 0871 for Class “B” equipment without additional noise filtering.
Cooling Forced air. 20 CFM required for full rating Derate 30% for convection cooling.
Input SpecificationsMulti Input (all units) 100/120/220/230/240 VAC selectable +/- 10% except 230 VAC is +15%, -6%
Frequency Range 47-63 Hz (Typical is 60 Hz. Derate output 10% at 50 Hz)
Transient Response Time 50 µsec at 50% load change
Fuse Requirements Units are not fused internally. For safe operation, user must provide input line fuse as per values given in table.
Output SpecificationsLine Regulation 0.05% for +/- 10% change
Load Regulation 0.05% for 50% change
Ripple 3.0 nV maximum peak-to-peak
DC Output Adjustment Range +/- 5% minimum
Overvoltage Protection OVP is optionally available
Overload Protection 125 to 150% foldback current limit
Output AdjustmentStep 1: Check the input AC connections
Step 2: Connect the AC input according to the table below.
Step 3: Use VR6 V.ADJ to adjust +V. Adj. to +15V or +12V
Step 4: Use VR4 V.ADJ to adjust -V. Adj. to -15V or -12V
4.00 " ( 102)
3.375" (86)
.188 "(4.8 )
1.62
"(4
1.5)
° MTG HOLES (6 PLACES)
VR4V.ADJ
.50" (12.5)
. 75" (19)
5.75
0"(146
)
.25" (6.5 )
6.50
"(1
65)
AC
INPU
T/D
CO
UTP
UT
OVP(OPTIONAL )
.75" (19)
. 45" (11.5)
4
1
23
5
+12
-12COM
Case H1
MAX WEIGHT: 2.21 LBS(1 KG )
PEM NUT HOLES6-32 MTG (2 PLACES)
VR6V.ADJ
VR5I.LIM
VR3 I.LIM
Contact Technical Services at 1-800-377-4384 or [email protected] with any questions. Visit our website at www.solaheviduty.com
Contact Technical Services at 1-800-377-4384 or [email protected] with any questions. Visit our website at www.solaheviduty.com
*Note: Unit is shipped for 120V input from factory.
Note: I. LIM is factory set and should not be adjusted by users.
Application Note: User needs to provide earth ground to power supply with either solder to Tab or using washer and nut assembly.
• Easy installation with strip terminal
• Output adjustable from 12V to 15V
• Tight regulation: 0.05% Line; 0.05% Load
• Full Output Ratings to +50oC
• OVP Option for 12V and 15V.
• Foldback Current Limiting Overload Protection with Automatic Recovery
• Multi-Tap AC Inputs
• 100% Four-Hour Burn-in
• Please see enclosed “Terms & Conditions and Sales & Policies & Procedures”
• UL Recognized
• CSA Certified
Serie SL - Lineales de Salida Sencilla & Múltiple Manual de la Instrucción
Modelo: SLD-12-1010-12T
CaracterísticasInput AC Conexiones
Para el uso en: Conecte Aplique AC a: El fusible primario
100 VAC 1-3, 2-4 1 & 5 0.63A/125V
120 VAC* 1-3, 2-4 1 & 4 0.63A/125V
220 VAC 2-3 1 & 5 0.315A/250V
230 VAC 2-3 1 & 4 0.315A/250V
240 VAC 2-3 1 & 4 0.315A/250V
Caja H1
Especificaciones
El Ajuste de SalidaDé un paso 1: Verifica las conexiones de entrada de C.A.
Dé un paso 2: Conecte a la entrada de C.A. según posponer abajo.
Dé un paso 3: Utilice VR6 V.ADJ para ajustar +V. Adj. to +15V or +12V
Dé un paso 4: Utilice VR4 V.ADJ para ajustar -V. Adj. to -15V or -12V
Contacte los Servicios Técnicos en 1-847-268-6000 o [email protected] con cualquiera preguntan. Visite nuestro sitio web en www.solaheviduty. com
P/N A272-135 Rev. 4 (August 16, 2007)
Contacte los Servicios Técnicos en 1-847-268-6000 o [email protected] con cualquiera preguntan. Visite nuestro sitio web en www.solaheviduty. com
La nota: I. LIM ha sido fijada en la fabrica y no se debe ajustar por los usuarios. La Nota de la aplicación: Las necesidades de Usuario a proporcionar la tierra el suelo para accionar el suministro
con o soldadura qa la Etiqueta o utilizar arandela y asamblea de nuez.
* La nota: La unidad se envía para la entrada 120V de la fábrica.
Dimensiones (pulg/mm)Voltaje/Las Calificaciones Actuales
Número de Catálogo Salida 1 Salida 2
SLD-12-1010-12T +12V/1.0A or +15V/0.8A -12V/1.0A or -15V/0.8A
*Outputs are tied common
Rango de Operación de Temperatura 0 to +50oC (Ajuste al 40% a +70oC)
Coeficiente de Temperatura (Típico) +/- 0.01% / oC
Estabilidad Después del calentamiento inicial, ±.5%
Vibración De acuerdo con MIL-STD-810C, Método 514
Golpes De acuerdo con MIL-STD-810C, Método 516
EMI/RFI Las fuentes de alimentación lineales tienen inherentemente bajos niveles de ruido conducido y radiado. Para la mayoría de las aplicaciones en sistemas estas cumplen con los requerimientos de FCC Clase B y VDE 0871 para Clase B.
Enfriamiento De aire forzado. 20 CFM requeridos para el grado completo reducen la capacidad normal del 30% para refrescarse de la convección.
EntradaVoltaje de Entrada 100/120/220/230/240 VAC selectable +/- 10% except 230 VAC is +15%, -6%
Frecuencia de Entrada 47-63 Hz (Típico es 60 Hz. La producción de Derate 10% en 50 Hz)
Tiempo de Respuesta a Transientes 50 µsec at 50% load change
Funda los Requisitos Las unidades no se funden internamente. Para la operación segura, el usuario debe proporcionar fusible de entrada de línea como por valores se rindió tabla.
SalidaRegulación de Línea 0.05% para un cambio del 10%
Regulación de la carga 0.05% para un cambio del 50%
Rizo 3.0 mV máximo Pico-a-Pico
Rango de Ajuste de CD de Salida +/- 5% Mínimo
Protección de Sobrevoltaje OVP is optionally available
Protección contra Sobrecarga 125 to 150% foldback automático de limitación de corriente
• Terminales de conexión fáciles de instalar.
• De salida ajustable de 12V a 15V
• Tight regulation: 0.05% Line; 0.05% Load
• Las calificaciones de salida a +50oC
• OVP Option for 12V and 15V.
• Foldback Current Limiting Protección contra Sobrecarga con Automático Recupera
• Multi-Tap AC Las Entradas
• 100% Cuatro Hora Burn-in
• Sírvase consultar “Términos y Condiciones, y Políticas y Procedimientos de Ventas”
• UL Reconocido
• CSA Certificado
4.00 " ( 102)
3.375" (86)
.188 "(4.8 )
1.62
"(4
1.5)
° MTG HOLES (6 PLACES)
VR4V.ADJ
.50" (12.5)
. 75" (19)
5.75
0"(146
)
.25" (6.5 )
6.50
"(1
65)
AC
INPU
T/D
CO
UTP
UT
OVP(OPTIONAL )
.75" (19)
. 45" (11.5)
4
1
23
5
+12
-12COM
Case H1
MAX WEIGHT: 2.21 LBS(1 KG )
PEM NUT HOLES6-32 MTG (2 PLACES)
VR6V.ADJ
VR5I.LIM
VR3 I.LIM
Linear Open Frame DC Power SuppliesSilver Line Instruction Manual
Model: SLD-12-1818-12T
FeaturesInput AC Connections
Mechanical Dimensions: inches (mm)
For use at: Connect Apply AC to: Primary Fuse
100 VAC 1-3, 2-4 1 & 5 1.0A / 125V
120 VAC 1-3, 2-4 1 & 4 1.0A / 125V
220 VAC 2-3 1 & 5 0.5A / 250V
230 VAC 2-3 1 & 4 0.5A / 250V
240 VAC 2-3 1 & 4 0.5A / 250V
Case D
General Specifications
Voltage/Current RatingsModel Number Output 1 Output 2
SLD-12-1818-12T +12V/1.8A or +15V/1.5A -12V/1.8A or -15V/1.5A
1. Outputs are tied common.2. Outputs are not isolated from one another.3 Refer to Adjustment section.
Operating Temperature Range 0 to +50oC (Derate to 40% at +70oC)
Temperature Coefficient (Typical) +/- 0.01% / oC
Stability Within +/- 0.05% (For 24 hours after warm-up)
Vibration Per MIL-STD-810C, Method 514
Shock Per MIL-STD-810C, Method 516
EMI/RFI Linear power supplies have inherently low conducted and radiated noise levels. For most system applications, these power supplies will meet the requirements of FCC Class “B” and VDE 0871 for Class “B” equipment without additional noise filtering.
Cooling Forced air. 20 CFM required for full rating Derate 30% for convection cooling.
Input SpecificationsMulti Input (all units) 100/120/220/230/240 VAC selectable +/- 10% except 230 VAC is +15%, -6%
Frequency Range 47-63 Hz (Typical is 60 Hz. Derate output 10% at 50 Hz)
Transient Response Time 50 µsec at 50% load change
Fuse Requirements Units are not fused internally. For safe operation, user must provide input line fuse as per values given in table.
Output Specifications
Line Regulation 0.05% for +/- 10% change
Load Regulation 0.05% for 50% change
Ripple 3.0 mV maximum peak-to-peak
DC Output Adjustment Range +/- 5% minimum
Overvoltage Protection OVP is optionally available
Remote Sensing All units listed have remote sensing capability.
Overload Protection 125 to 150% foldback current limit
Output AdjustmentStep 1: Check the input AC connections
Step 2: Connect the AC input according to the table below.
Step 3: Use VR6 to adjust +V. Adj. to +15V or +12V.
Step 4: Use VR4 to adjust -V. Adj. to -15V or -12V
Contact Technical Services at 1-800-377-4384 or [email protected] with any questions. Visit our website at www.solaheviduty.com
Contact Technical Services at 1-800-377-4384 or [email protected] with any questions. Visit our website at www.solaheviduty.com
4.87" (124)
4.125" (105)
. 188"(4.8 )
2.50
"63
.5)
1.25
0 "(32)
° MTG HOLES (8 PLACES ). 50" (12.5)
. 75" (19)
7.00
"(178
)
0.25" (6.5 )
6.25
0"(159
)
AC
INPU
T/DCOUTP
UT
OVP
(OPT
IONAL )
. 75" (19)1.25" (32)
MAX
.450" (11.5)
.24"
(6)
4
1
23
5
-12
+12
COM
WEIGHT: 4.41 LBS (2 KG)
PEM NU T H OLES8-32 MT G(4 PLACES)
VR6V.ADJ
VR4V.ADJ VR5
I.LIM
VR3I.LIM
*Note: Unit is shipped for 120V input from factory.
Note: I. LIM is factory set and should not be adjusted by users.
Application Note: User needs to provide earth ground to power supply with either solder to Tab or using washer and nut assembly.
• Easy installation with strip terminal• Output adjustable from 12V to 15V• Tight regulation: 0.05% Line; 0.05% Load• Full Output Ratings to +50oC• OVP Option for 12V and 15V • Foldback Current Limiting Overload Protection with
Automatic Recovery
• Multi-Tap AC Inputs• 100% Four-Hour Burn-in• Please see enclosed “Terms & Conditions and
Sales & Policies & Procedures”• UL Recognized• CSA Certified
Serie SL - Lineales de Salida Sencilla & Múltiple Manual de la Instrucción
Modelo: SLD-12-1818-12T
CaracterísticasEntrada AC Conexiones
Caja D
Especificaciones
El Ajuste de SalidaDé un paso 1: Verifica las conexiones de entrada de C.A.
Dé un paso 2: Conecte a la entrada de C.A. según posponer abajo.
Dé un paso 3: Utilice VR6 para ajustar +V. Adj. to +15V or +12V
Dé un paso 4: Utilice VR4 para ajustar -V. Adj. to -15V or -12V
Contacte los Servicios Técnicos en 1-847-268-6000 o [email protected] con cualquiera preguntan. Visite nuestro sitio web en www.solaheviduty. com
Para el uso en: Conecte Aplique AC a: El fusible primario
100 VAC 1-3, 2-4 1 & 5 1.0A / 125V
120 VAC 1-3, 2-4 1 & 4 1.0A / 125V
220 VAC 2-3 1 & 5 0.5A / 250V
230 VAC 2-3 1 & 4 0.5A / 250V
240 VAC 2-3 1 & 4 0.5A / 250V
P/N A272-049 Rev. 3 (August 17, 2007)
Contacte los Servicios Técnicos en 1-847-268-6000 o [email protected] con cualquiera preguntan. Visite nuestro sitio web en www.solaheviduty. com
* La nota: La unidad se envía para la entrada 120V de la fábrica. Voltaje/Las Calificaciones Actuales
Número de Catálogo Salida 1 Salida 2
SLD-12-1818-12T +12V/1.8A or +15V/1.5A -12V/1.8A or -15V/1.5A
1. Outputs are tied common.2. Outputs are not isolated from one another.3 Refer to Adjustment section.
Rango de Operación de Temperatura 0 to +50oC (Ajuste al 40% a +70oC)
Coeficiente de Temperatura (Típico) +/- 0.01% / oC
Estabilidad Después del calentamiento inicial, ±.5%
Vibración De acuerdo con MIL-STD-810C, Método 514
Golpes De acuerdo con MIL-STD-810C, Método 516
EMI/RFI Las fuentes de alimentación lineales tienen inherentemente bajos niveles de ruido conducido y radiado. Para la mayoría de las aplicaciones en sistemas estas cumplen con los requerimientos de FCC Clase B y VDE 0871 para Clase B.
Enfriamiento De aire forzado. 20 CFM requeridos para el grado completo reducen la capacidad normal del 30% para refrescarse de la convección.
EntradaVoltaje de Entrada 100/120/220/230/240 VAC selectable +/- 10% except 230 VAC is +15%, -6%
Frecuencia de Entrada 47-63 Hz (Típico es 60 Hz. La producción de Derate 10% en 50 Hz)
Tiempo de Respuesta a Transientes 50 µsec at 50% load change
Funda los Requisitos Las unidades no se funden internamente. Para la operación segura, el usuario debe proporcionar fusible de entrada de línea como por valores se rindió tabla.
SalidaRegulación de Línea 0.05% para un cambio del 10%
Regulación de la carga 0.05% para un cambio del 50%
Rizo 3.0 mV máximo Pico-a-Pico
Rango de Ajuste de CD de Salida +/- 5% Mínimo
Protección de Sobrevoltaje OVP is optionally available
Protección contra Sobrecarga 125 to 150% foldback automático de limitación de corriente
Sensores Remotos Todas unidades listaron tiene la capacidad de sensores remotos.
La nota: I. LIM ha sido fijada en la fabrica y no se debe ajustar por los usuarios.
La Nota de la aplicación: Las necesidades de Usuario a proporcionar la tierra el suelo para accionar el suministro con o soldadura qa la Etiqueta o utilizar arandela y asamblea de nuez.
Dimensiones (pulg/mm)
• Terminales de conexión fáciles de instalar. • De salida ajustable de 12V a 15V• Tight regulation: 0.05% Line; 0.05% Load• Las calificaciones de salida a +50oC• OVP Option for 12V and 15V • Foldback Current Limiting Protección contra
Sobrecarga con Automático Recupera
• Multi-Tap AC Las Entradas• 100% Cuatro Hora Burn-in• Sírvase consultar “Términos y Condiciones, y
Políticas y Procedimientos de Ventas” • UL Reconocido• CSA Certified
4.87" (124)
4.125" (105)
. 188"(4.8 )
2.50
"63
.5)
1.25
0 "(32)
° MTG HOLES (8 PLACES ). 50" (12.5)
. 75" (19)
7.00
"(178
)
0.25" (6.5 )
6.25
0"(159
)
AC
INPU
T/DCOUTP
UT
OVP
(OPT
IONAL )
. 75" (19)1.25" (32)
MAX
.450" (11.5)
.24"
(6)
4
1
23
5
-12
+12
COM
WEIGHT: 4.41 LBS (2 KG)
PEM NU T H OLES8-32 MT G(4 PLACES)
VR6V.ADJ
VR4V.ADJ VR5
I.LIM
VR3I.LIM
Linear Open Frame DC Power SuppliesSilver Line Instruction Manual
Model: SLD-12-3015-05T
Features
General Specifications
Voltage/Current RatingsModel Number Output 1 Output 2
SLD-12-3015-15T +5V/3.0A1 +12V/1.5A1
1. Outputs are isolated from one another.
Operating Temperature Range 0 to +50oC (Derate to 40% at +70oC)
Temperature Coefficient (Typical) +/- 0.01% / oC
Stability Within +/- 0.05% (For 24 hours after warm-up)
Vibration Per MIL-STD-810C, Method 514
Shock Per MIL-STD-810C, Method 516
EMI/RFI Linear power supplies have inherently low conducted and radiated noise levels. For most system applications, these power supplies will meet the requirements of FCC Class “B” and VDE 0871 for Class “B” equipment without additional noise filtering.
Cooling Forced air 20 CFM required for full rating. Derate 30% for convection cooling.
Input SpecificationsMulti Input (all units) 100/120/220/230/240 VAC selectable +/- 10% except 230 VAC is +15%, -6%
Frequency Range 47-63 Hz (Typical is 60 Hz. Derate output 10% at 50 Hz)
Transient Response Time 50 µsec at 50% load change
Fuse Requirements Units are not fused internally. For safe operation, user must provide input line fuse as per values given in table.
Output Specifications
Line Regulation 0.05% for +/- 10% change
Load Regulation 0.05% for 50% change
Ripple 3.0 mV maximum peak-to-peak
DC Output Adjustment Range +/- 5% minimum
Overvoltage Protection OVP is optionally available
Remote Sensing Refer to Figure 1 for the output(s) with remote sensing.
Overload Protection 125 to 150% foldback current limit
Contact Technical Services at 1-800-377-4384 or [email protected] with any questions. Visit our website at www.solaheviduty.com
Contact Technical Services at 1-800-377-4384 or [email protected] with any questions. Visit our website at www.solaheviduty.com
Input AC Connections
Mechanical Dimensions: inches (mm)
For use at: Connect Apply AC to: Primary Fuse
100 VAC 1-3, 2-4 1 & 5 1.0A / 125V
120 VAC* 1-3, 2-4 1 & 4 1.0A / 125V
220 VAC 2-3 1 & 5 0.5A / 250V
230 VAC 2-3 1 & 4 0.5A / 250V
240 VAC 2-3 1 & 4 0.5A / 250V
*Note: Unit is shipped for 120V input from factory.
Application Note: User needs to provide earth ground to power supply with either solder to Tab or using washer and nut assembly. The SLD power supply is shipped from the factory with metal shorting straps connected between the + OUT and + S terminals and the (-) OUT and (-) S terminals. This strapping configuration allows the output of the SLS to be taken from either pair of terminals. This is the standard configuration. The remote sense feature is enabled by removing the shorting straps and connecting the individual OUT and S terminals to the appropriate points of the load. If an OVP circuit is used it should be connected to the + OUT and (-) OUT terminals. The OVP should never be connected to the + S, - S terminals without the use of the shorting straps. In all cases it is critical that the terminal screws be firmly tightened.
Note: I. LIM is factory set on all models and should not be adjusted by users.
7.00 " ( 178)
6.250" (158.8)
AC INPUT/DC OUTPUT
.50" (12.7)
. 50" (12.9)
75”
0.83 (21.08) 6.27 (159.26)
(19.1)
4.87
"(1
23.7
)2.
75"
(69.
9)
1.24
8"
( 31.
7)
. 38" (9.6 )
4.12
5"(1
04.8
)
OVP (OPTIONAL)° MTG HOLES (12 PLACES)
1.248" (31.7) . 75" (19.1)
188"(4.8 )
MA X
. 551" (14)
WEIGH T: 7.28 LBS.(3.3 KG)
PEM NU T HOLES8-32 MTG (4 PLACES)
Top View
VR2V. ADJ
VR1I.LIM
VR3I.LIM
VR4V. ADJ
Case C1
Output AdjustmentStep 1: Check the input AC connections
Step 2: Connect the AC input according to the table below.
Step 3: Use VR2 to adjust +V. Adj. to +5V.
Step 4: Use VR4 to adjust +V. Adj. to +12V
• Easy installation with terminal strip• Tight regulation: 0.05% Line; 0.05% Load• Full Output Ratings to +50oC• OVP Option 12V• Foldback Current Limiting Overload Protection with
Automatic Recovery
• Multi-Tap AC Inputs• 100% Four-Hour Burn-in• Please see enclosed “Terms & Conditions and
Sales & Policies & Procedures”• UL Recognized• CSA Certified
Serie SL - Lineales de Salida Sencilla & Múltiple Manual de la Instrucción
Modelo: SLD-12-3015-05T
Características
Especificaciones
Contacte los Servicios Técnicos en 1-847-268-6000 o [email protected] con cualquiera preguntan. Visite nuestro sitio web en www.solaheviduty. com
Contacte los Servicios Técnicos en 1-847-268-6000 o [email protected] con cualquiera preguntan. Visite nuestro sitio web en www.solaheviduty. com
P/N A272-136 Rev. 3 (August 17, 2007)
Voltaje/Las Calificaciones ActualesNúmero de Catálogo Salida 1 Salida 2
SLD-12-3015-15T +5V/3.0 A1 +12V/1.5A1
1.Las salidas se aíslan del uno al otro.
Rango de Operación de Temperatura 0 to +50oC (Ajuste al 40% a +70oC)
Coeficiente de Temperatura (Típico) +/- 0.01% / oC
Estabilidad Después del calentamiento inicial, ±.5%
Vibración De acuerdo con MIL-STD-810C, Método 514
Golpes De acuerdo con MIL-STD-810C, Método 516
EMI/RFI Las fuentes de alimentación lineales tienen inherentemente bajos niveles de ruido conducido y radiado. Para la mayoría de las aplicaciones en sistemas estas cumplen con los requerimientos de FCC Clase B y VDE 0871 para Clase B.
Enfriamiento De aire forzado. 20 CFM requeridos para el grado completo reducen la capacidad normal del 30% para refrescarse de la convección.
EntradaVoltaje de Entrada 100/120/220/230/240 VAC selectable +/- 10% except 230 VAC is +15%, -6%
Frecuencia de Entrada 47-63 Hz (Típico es 60 Hz. La producción de Derate 10% en 50 Hz)
Tiempo de Respuesta a Transientes 50 µsec at 50% load change
Funda los Requisitos Las unidades no se funden internamente. Para la operación segura, el usuario debe proporcionar fusible de entrada de línea como por valores se rindió tabla.
SalidaRegulación de Línea 0.05% para un cambio del 10%
Regulación de la carga 0.05% para un cambio del 50%
Rizo 3.0 mV máximo Pico-a-Pico
Rango de Ajuste de CD de Salida +/- 5% Mínimo
Protección de Sobrevoltaje Todas las salidas de 5-Volt incluyen OVP integrada como un estándar (el ajuste es 6.2 V ±0.4 V) OVP está disponible opcionalmente en otros tipos
Presentir de telemando OVP is optionally available
Protección contra Sobrecarga 125 to 150% foldback automático de limitación de corriente
Sensores Remotos Todas unidades listaron tiene la capacidad de sensores remotos.
Caja C1
Entrada AC Conexiones
Para el uso en: Conecte Aplique AC a: El fusible primario
100 VAC 1-3, 2-4 1 & 5 1.0A / 125V
120 VAC* 1-3, 2-4 1 & 4 1.0A / 125V
220 VAC 2-3 1 & 5 0.5A / 250V
230 VAC 2-3 1 & 4 0.5A / 250V
240 VAC 2-3 1 & 4 0.5A / 250V
* La nota: La unidad se envía para la entrada 120V de la fábrica.
Dimensiones (pulg/mm)
La Nota de la aplicación: Las necesidades de Usuario a proporcionar la tierra el suelo para accionar el suministro con o soldadura qa la Etiqueta o utilizar arandela y asamblea de nuez. La planta SLD se envía de fábrica con bandas metálicas de cortocircuito conectadas entre los terminales + OUT (salida) y + S y los terminales (-) OUT y (-) S. Esta configuración de bandas permite la salida desde la SLS desde cualquier par de terminales, y es la configuración estándar. La función de sensor remoto se activa al retirar las bandas de cortocircuito y conectar los terminales individuales de salida (OUT) y S con los puntos pertinentes de la carga. Si se utiliza un circuito OVP, deberá conectarse con los terminales + OUT y (-) OUT. El circuito OVP no debe conectarse nunca con los terminales + S, - S sin las bandas de cortocircuito. En todos los casos es esencial ajustar los tornillos del terminal firmemente.
La nota: I. LIM ha sido fijada en la fabrica y no se debe ajustar por los usuarios.
7.00 " ( 178)
6.250" (158.8)
AC INPUT/DC OUTPUT
.50" (12.7)
. 50" (12.9)
75”
0.83 (21.08) 6.27 (159.26)
(19.1)
4.87
"(1
23.7
)2.
75"
(69.
9)
1.24
8"
( 31.
7)
. 38" (9.6 )
4.12
5"(1
04.8
)
OVP (OPTIONAL)° MTG HOLES (12 PLACES)
1.248" (31.7) . 75" (19.1)
188"(4.8 )
MA X
. 551" (14)
WEIGH T: 7.28 LBS.(3.3 KG)
PEM NU T HOLES8-32 MTG (4 PLACES)
Top View
VR2V. ADJ
VR1I.LIM
VR3I.LIM
VR4V. ADJ
El Ajuste de SalidaDé un paso 1: Verifica las conexiones de entrada de C.A.
Dé un paso 2: Conecte a la entrada de C.A. según posponer abajo.
Dé un paso 3: Utilice VR2 para ajustar +V. Adj. to +5V.
Dé un paso 4: Utilice VR4 para ajustar -V. Adj. to +12V.
• Terminales de conexión fáciles de instalar. • Tight regulation: 0.05% Line; 0.05% Load• Las calificaciones de salida a +50oC• OVP Option 12V• Foldback Current Limiting Protección contra
Sobrecarga con Automático Recupera
• Multi-Tap AC Las Entradas• 100% Cuatro Hora Burn-in• Sírvase consultar “Términos y Condiciones, y
Políticas y Procedimientos de Ventas” • UL Reconocido• CSA Certificado
Linear Open Frame DC Power SuppliesSilver Line Instruction Manual
Model: SLD-12-3434-12T
Features• Easyinstallationwithstripterminal• Tightregulation:0.05%Line;0.05%Load• FullOutputRatingsto+50oC• OVPOptionfor12V• FoldbackCurrentLimitingOverloadProtection
withAutomaticRecovery
Input AC Connections
Mechanical Dimensions: inches (mm)
For use at: Connect Apply AC to: Primary Fuse
100VAC 1-3,2-4 1&5 2.5A/125V
120VAC 1-3,2-4 1&4 2.5A/125V
220VAC 2-3 1&5 1.25A/250V
230VAC 2-3 1&4 1.25A/250V
240VAC 2-3 1&4 1.25A/250V
• Multi-TapACInputs• 100%Four-HourBurn-in• LimitedWarrantyfortwoyears• ULRecognized• CSACertified
General Specifications
Voltage/Current RatingsModelNumber Output1 Output2
SLD-12-3434-12T +12V/3.4A1 -12V/3.4A1
1.Outputsareisolatedfromoneanother.
OperatingTemperatureRange 0to+50oC(Derateto40%at+70oC)
TemperatureCoefficient(Typical) +/-0.01%/oC
Stability Within+/-0.05%(For24hoursafterwarm-up)
Vibration PerMIL-STD-810C,Method514
Shock PerMIL-STD-810C,Method516
EMI/RFI Linearpowersupplieshaveinherentlylowconductedandradiatednoiselevels.Formostsystemapplications,thesepowersupplieswillmeettherequirementsofFCCClass“B”andVDE0871forClass“B”equipmentwithoutadditionalnoisefiltering.
Cooling Forcedair.20CFMrequiredforfullratingDerate30%forconvectioncooling.
Input SpecificationsMultiInput(allunits) 100/120/220/230/240VACselectable+/-10%except230VACis+15%,-6%
FrequencyRange 47-63Hz(Typicalis60Hz.Derateoutput10%at50Hz)
TransientResponseTime 50µsecat50%loadchange
FuseRequirements Unitsarenotfusedinternally.Forsafeoperation,usermustprovideinputlinefuseaspervaluesgivenintable.
Output Specifications
LineRegulation 0.05%for+/-10%change
LoadRegulation 0.05%for50%change
Ripple 3.0mVmaximumpeak-to-peak
DCOutputAdjustmentRange +/-5%minimum
OvervoltageProtection OVPisoptionallyavailable
RemoteSensing RefertotheInputACConnectionschartfortheoutput(s)withremotesensing.
OverloadProtection 125to150%foldbackcurrentlimit
Contact Technical Services at 1-800-377-4384 or [email protected] with any questions. Visit our website at www.solaheviduty.com
Contact Technical Services at 1-800-377-4384 or [email protected] with any questions. Visit our website at www.solaheviduty.com
Case I3
OVP (OPTIONAL)
8.00" (203). 512" (13)
9.00" (229)AC INPUT/DC OUTPUT
°MTG HOLES (12 PLACES)
. 473" (12). 188"(4.8 )
. 75" (19)
4.8
7"
(12
4)
2.7
5"
( 70
)
1.2
50
"(3
2)
4.1
25
"( 1
05
)
1.250" (32)
.39
"(1
0)
. 75" (19)
MAX
. 551" (14)
WEIGHT: 7. 5 LBS.(3.4 KG)
PEM NUT HOLES8-32 MTG (4 PLACES)
+O
UT
+O
UT
-O
UT
-S
+S
-S-O
UT
+S
AC Input 12/15V
41 235
12/15V
R9V.ADJ
R13I.LIM
R20V.ADJR5
I.LIM
*Note:Unitisshippedfor120Vinputfromfactory.
Application Note:UserneedstoprovideearthgroundtopowersupplywitheithersoldertoTaborusingwasherandnutassembly.TheSLSpowersupplyisshippedfromthefactorywithmetalshortingstrapsconnectedbetweenthe+OUTand+Sterminalsandthe(-)OUTand(-)Sterminals.ThisstrappingconfigurationallowstheoutputoftheSLStobetakenfromeitherpairofterminals.Thisisthestandardconfiguration.Theremote sensefeatureisenabledbyremovingtheshortingstrapsandconnectingtheindividualOUTandSterminalstotheappropriatepointsoftheload.IfanOVPcircuitisuseditshouldbeconnectedtothe+OUTand(-)OUTterminals.TheOVPshouldneverbeconnectedtothe+S,-Sterminalswithouttheuseoftheshortingstraps.Inallcasesitiscriticalthattheterminalscrewsbefirmly tightened.
Note:TheDCoutputscanbeadjustedwithV.ADJ.I. LIM is factory set on all models and should not be adjusted by users.
Serie SL - Lineales de Salida Sencilla & Múltiple Manual de la Instrucción
Modelo: SLD-12-3434-12T
Características•Terminalesdeconexiónfácilesdeinstalar.•Desalidaajustablede12Va15V•Tightregulation:0.05%Line;0.05%Load•Lascalificacionesdesalidaa+50oC•OVPOption12V•FoldbackCurrentLimitingProteccióncontra
SobrecargaconAutomáticoRecupera
Entrada AC Conexiones
Caja I3
•Multi-TapACLasEntradas•100%CuatroHoraBurn-in•Dosañosdegarantía.•ULReconocido•CSACertificado
Especificaciones
Contacte los Servicios Técnicos en 1-847-268-6000 o [email protected] con cualquiera preguntan. Visite nuestro sitio web en www.solaheviduty. com
Para el uso en: Conecte Aplique AC a: El fusible primario
100VAC 1-3,2-4 1&5 2.5A/125V
120VAC* 1-3,2-4 1&4 2.5A/125V
220VAC 2-3 1&5 1.25A/250V
230VAC 2-3 1&4 1.25A/250V
240VAC 2-3 1&4 1.25A/250V
P/N A272-011 Rev. 2 (April 21, 2006)
Contacte los Servicios Técnicos en 1-847-268-6000 o [email protected] con cualquiera preguntan. Visite nuestro sitio web en www.solaheviduty. com
*Lanota:Launidadseenvíaparalaentrada120Vdelafábrica.
OVP (OPTIONAL)
8.00" (203). 512" (13)
9.00" (229)AC INPUT/DC OUTPUT
°MTG HOLES (12 PLACES)
. 473" (12). 188"(4.8 )
. 75" (19)
4.8
7"
(12
4)
2.7
5"
(70
)
1.2
50
"(3
2)
4.1
25
"(1
05
)
1.250" (32)
.39
"(1
0)
. 75" (19)
MAX
. 551" (14)
WEIGHT: 7. 5 LBS.(3.4 KG)
PEM NUT HOLES8-32 MTG (4 PLACES)
+O
UT
+O
UT
-O
UT
-S
+S
-S-O
UT
+S
AC Input 12/15V
41 235
12/15V
R9V.ADJ
R13I.LIM
R20V.ADJR5
I.LIM
Voltaje/Las Calificaciones ActualesNúmerodeCatálogo Salida1 Salida2
SLD-12-3434-12T +12V/3.4A1 -12V/3.4A1
1.Lassalidasseaíslandelunoalotro.
RangodeOperacióndeTemperatura
0to+50oC(Ajusteal40%a+70oC)
CoeficientedeTemperatura(Típico) +/-0.01%/oC
Estabilidad Despuésdelcalentamientoinicial,±.5%
Vibración DeacuerdoconMIL-STD-810C,Método514
Golpes DeacuerdoconMIL-STD-810C,Método516
EMI/RFI Lasfuentesdealimentaciónlinealestieneninherentementebajosnivelesderuidoconducidoyradiado.ParalamayoríadelasaplicacionesensistemasestascumplenconlosrequerimientosdeFCCClaseByVDE0871paraClaseB.
Enfriamiento Deaireforzado.20CFMrequeridosparaelgradocompletoreducenlacapacidadnormaldel30%pararefrescarsedelaconvección.
EntradaVoltajedeEntrada 100/120/220/230/240VACselectable+/-10%except230VACis+15%,-6%
FrecuenciadeEntrada 47-63Hz(Típicoes60Hz.LaproduccióndeDerate10%en50Hz)
TiempodeRespuestaaTransientes 50µsecat50%loadchange
FundalosRequisitos Lasunidadesnosefundeninternamente.Paralaoperaciónsegura,elusuariodebeproporcionarfusibledeentradadelíneacomoporvaloresserindiótabla.
SalidaRegulacióndeLínea 0.05%parauncambiodel10%
Regulacióndelacarga 0.05%parauncambiodel50%
Rizo 3.0mVmáximoPico-a-Pico
RangodeAjustedeCDdeSalida +/-5%Mínimo
ProteccióndeSobrevoltaje OVPisoptionallyavailable
ProteccióncontraSobrecarga 125to150%foldbackautomáticodelimitacióndecorriente
SensoresRemotos Todasunidadeslistarontienelacapacidaddesensoresremotos.
La Nota de la aplicación:LasnecesidadesdeUsuarioaproporcionarlatierraelsueloparaaccionarelsuministroconosoldaduraqalaEtiquetaoutilizararandelayasambleadenuez.LaplantaSLSseenvíadefábricaconbandasmetálicasdecortocircuitoconectadasentrelosterminales+OUT(salida)y+Sylosterminales(-)OUTy(-)S.EstaconfiguracióndebandaspermitelasalidadesdelaSLSdesdecualquierpardeterminales,yeslaconfiguraciónestándar.Lafuncióndesensorremotoseactivaalretirarlasbandasdecortocircuitoyconectarlosterminalesindividualesdesalida(OUT)ySconlospuntospertinentesdelacarga.SiseutilizauncircuitoOVP,deberáconectarseconlosterminales+OUTy(-)OUT.ElcircuitoOVPnodebeconectarsenuncaconlosterminales+S,-Ssinlasbandasdecortocircuito.Entodosloscasosesesencialajustarlostornillosdelterminalfirmemente.
Dimensiones (pulg/mm)
Lanota:LasalidadelaC.C.sepuedeajustarconelajustedelV.ADJ.I. LIM ha sido fijada en la fabrica y no se debe ajustar por los usuarios.
Linear Open Frame DC Power SuppliesSilver Line Instruction Manual
Model: SLD-12-6034-05T
Features
General Specifications
Voltage/Current RatingsModel Number Output 1 Output 2
SLD-12-6034-05T +5V/6.0A1 +12V/3.4A1
1. Outputs are isolated from one another.
Operating Temperature Range 0 to +50oC (Derate to 40% at +70oC)
Temperature Coefficient (Typical) +/- 0.01% / oC
Stability Within +/- 0.05% (For 24 hours after warm-up)
Vibration Per MIL-STD-810C, Method 514
Shock Per MIL-STD-810C, Method 516
EMI/RFI Linear power supplies have inherently low conducted and radiated noise levels. For most system applications, these power supplies will meet the requirements of FCC Class “B” and VDE 0871 for Class “B” equipment without additional noise filtering.
Cooling Forced air 20 CFM required for full rating. Derate 30% for convection cooling.
Input SpecificationsMulti Input (all units) 100/120/220/230/240 VAC selectable +/- 10% except 230 VAC is +15%, -6%
Frequency Range 47-63 Hz (Typical is 60 Hz. Derate output 10% at 50 Hz)
Transient Response Time 50 µsec at 50% load change
Fuse Requirements Units are not fused internally. For safe operation, user must provide input line fuse as per values given in table.
Output Specifications
Line Regulation 0.05% for +/- 10% change
Load Regulation 0.05% for 50% change
Ripple 3.0 mV maximum peak-to-peak
DC Output Adjustment Range +/- 5% minimum
Overvoltage Protection OVP is optionally available
Remote Sensing Refer to Figure 1 for the output(s) with remote sensing.
Overload Protection 125 to 150% foldback current limit
Contact Technical Services at 1-800-377-4384 or [email protected] with any questions. Visit our website at www.solaheviduty.com
Contact Technical Services at 1-800-377-4384 or [email protected] with any questions. Visit our website at www.solaheviduty.com
Input AC Connections
For use at: Connect Apply AC to: Primary Fuse
100 VAC 1-3, 2-4 1 & 5 2.5A / 125V
120 VAC* 1-3, 2-4 1 & 4 2.5A / 125V
220 VAC 2-3 1 & 5 1.25A / 250V
230 VAC 2-3 1 & 4 1.25A / 250V
240 VAC 2-3 1 & 4 1.25A / 250V
*Note: Unit is shipped for 120V input from factory.
Mechanical Dimensions: inches (mm)OVP (OPTIONAL)
8.00" (203). 512" (13)
9.00" (229)AC INPUT/DC OUTPUT
°MTG HOLES (12 PLACES). 473" (12)
. 188"(4.8 )
. 75" (19)
4.87
"(124
)2.75
"( 70)
1.25
0"(32)
4.12
5"(105
)
1.250" (32)
.39"
(10)
. 75" (19)
MAX
.551" (14)
WEIGHT: 7. 5 LBS.(3.4 KG)
+O
UT
41 235
+O
UT
-O
UT
-S
+S-S-O
UT
+S
AC Input 12V5V
PEM NUT HOLES8-32 MTG (4 PLACES)
VR2V.ADJ
VR1I.LIM
VR3I.LIM
VR4V.ADJ
Case I1
Application Note: User needs to provide earth ground to power supply with either solder to Tab or using washer and nut assembly. The SLD power supply is shipped from the factory with metal shorting straps connected between the + OUT and + S terminals and the (-) OUT and (-) S terminals. This strapping configuration allows the output of the SLS to be taken from either pair of terminals. This is the standard configuration. The remote sense feature is enabled by removing the shorting straps and connecting the individual OUT and S terminals to the appropriate points of the load. If an OVP circuit is used it should be connected to the + OUT and (-) OUT terminals. The OVP should never be connected to the + S, - S terminals without the use of the shorting straps. In all cases it is critical that the terminal screws be firmly tightened.
Note: I. LIM is factory set on all models and should not be adjusted by users.
Output AdjustmentStep 1: Check the input AC connections
Step 2: Connect the AC input according to the table below.
Step 3: Use VR2 to adjust +V. Adj. to +5V.
Step 4: Use VR4 to adjust +V. Adj. to +12V
• Easy installation with terminal strip• Tight regulation: 0.05% Line; 0.05% Load• Full Output Ratings to +50oC• OVP Option 12V• Foldback Current Limiting Overload Protection with
Automatic Recovery
• Multi-Tap AC Inputs• 100% Four-Hour Burn-in• Please see enclosed “Terms & Conditions and
Sales & Policies & Procedures”• UL Recognized• CSA Certified
Serie SL - Lineales de Salida Sencilla & Múltiple Manual de la Instrucción
Modelo: SLD-12-6034-05T
Características
Especificaciones
Contacte los Servicios Técnicos en 1-847-268-6000 o [email protected] con cualquiera preguntan. Visite nuestro sitio web en www.solaheviduty. com
Contacte los Servicios Técnicos en 1-847-268-6000 o [email protected] con cualquiera preguntan. Visite nuestro sitio web en www.solaheviduty. com
P/N A272-050 Rev. 3 (August 17, 2007)
Voltaje/Las Calificaciones ActualesNúmero de Catálogo Salida 1 Salida 2
SLD-12-6034-05T +5V/6.0 A1 +12V/3.4A1
1.Las salidas se aíslan del uno al otro.
Rango de Operación de Temperatura 0 to +50oC (Ajuste al 40% a +70oC)
Coeficiente de Temperatura (Típico) +/- 0.01% / oC
Estabilidad Después del calentamiento inicial, ±.5%
Vibración De acuerdo con MIL-STD-810C, Método 514
Golpes De acuerdo con MIL-STD-810C, Método 516
EMI/RFI Las fuentes de alimentación lineales tienen inherentemente bajos niveles de ruido conducido y radiado. Para la mayoría de las aplicaciones en sistemas estas cumplen con los requerimientos de FCC Clase B y VDE 0871 para Clase B.
Enfriamiento De aire forzado. 20 CFM requeridos para el grado completo reducen la capacidad normal del 30% para refrescarse de la convección.
EntradaVoltaje de Entrada 100/120/220/230/240 VAC selectable +/- 10% except 230 VAC is +15%, -6%
Frecuencia de Entrada 47-63 Hz (Típico es 60 Hz. La producción de Derate 10% en 50 Hz)
Tiempo de Respuesta a Transientes 50 µsec at 50% load change
Funda los Requisitos Las unidades no se funden internamente. Para la operación segura, el usuario debe proporcionar fusible de entrada de línea como por valores se rindió tabla.
SalidaRegulación de Línea 0.05% para un cambio del 10%
Regulación de la carga 0.05% para un cambio del 50%
Rizo 3.0 mV máximo Pico-a-Pico
Rango de Ajuste de CD de Salida +/- 5% Mínimo
Protección de Sobrevoltaje Todas las salidas de 5-Volt incluyen OVP integrada como un estándar (el ajuste es 6.2 V ±0.4 V) OVP está disponible opcionalmente en otros tipos
Presentir de telemando OVP is optionally available
Protección contra Sobrecarga 125 to 150% foldback automático de limitación de corriente
Sensores Remotos Todas unidades listaron tiene la capacidad de sensores remotos.
Entrada AC Conexiones
Para el uso en: Conecte Aplique AC a: El fusible primario
100 VAC 1-3, 2-4 1 & 5 2.5A / 125V
120 VAC* 1-3, 2-4 1 & 4 2.5A / 125V
220 VAC 2-3 1 & 5 1.25A / 250V
230 VAC 2-3 1 & 4 1.25A / 250V
240 VAC 2-3 1 & 4 1.25A / 250V
* La nota: La unidad se envía para la entrada 120V de la fábrica.
OVP (OPTIONAL)
8.00" (203). 512" (13)
9.00" (229)AC INPUT/DC OUTPUT
°MTG HOLES (12 PLACES). 473" (12)
. 188"(4.8 )
. 75" (19)
4.87
"(124
)2.75
"( 70)
1.25
0"(32)
4.12
5"(105
)
1.250" (32)
.39"
(10)
. 75" (19)
MAX
.551" (14)
WEIGHT: 7. 5 LBS.(3.4 KG)
+O
UT
41 235
+O
UT
-O
UT
-S
+S-S-O
UT
+S
AC Input 12V5V
PEM NUT HOLES8-32 MTG (4 PLACES)
VR2V.ADJ
VR1I.LIM
VR3I.LIM
VR4V.ADJ
Caja I1
Dimensiones (pulg/mm)
La Nota de la aplicación: Las necesidades de Usuario a proporcionar la tierra el suelo para accionar el suministro con o soldadura qa la Etiqueta o utilizar arandela y asamblea de nuez. La planta SLD se envía de fábrica con bandas metálicas de cortocircuito conectadas entre los terminales + OUT (salida) y + S y los terminales (-) OUT y (-) S. Esta configuración de bandas permite la salida desde la SLS desde cualquier par de terminales, y es la configuración estándar. La función de sensor remoto se activa al retirar las bandas de cortocircuito y conectar los terminales individuales de salida (OUT) y S con los puntos pertinentes de la carga. Si se utiliza un circuito OVP, deberá conectarse con los terminales + OUT y (-) OUT. El circuito OVP no debe conectarse nunca con los terminales + S, - S sin las bandas de cortocircuito. En todos los casos es esencial ajustar los tornillos del terminal firmemente.
La nota: I. LIM ha sido fijada en la fabrica y no se debe ajustar por los usuarios.
El Ajuste de SalidaDé un paso 1: Verifica las conexiones de entrada de C.A.
Dé un paso 2: Conecte a la entrada de C.A. según posponer abajo.
Dé un paso 3: Utilice VR2 para ajustar +V. Adj. to +5V.
Dé un paso 4: Utilice VR4 para ajustar -V. Adj. to +12V.
• Terminales de conexión fáciles de instalar. • Tight regulation: 0.05% Line; 0.05% Load• Las calificaciones de salida a +50oC• OVP Option 15V• Foldback Current Limiting Protección contra
Sobrecarga con Automático Recupera
• Multi-Tap AC Las Entradas• 100% Cuatro Hora Burn-in• Sírvase consultar “Términos y Condiciones, y
Políticas y Procedimientos de Ventas” • UL Reconocido• CSA Certificado
Linear Open Frame DC Power SuppliesSilver Line Instruction Manual
Model: SLD-15-3030-15T
Features
Input AC Connections
Mechanical Dimensions: inches (mm)
For use at: Connect Apply AC to: Primary Fuse
100 VAC 1-3, 2-4 1 & 5 2.5A / 125V
120 VAC* 1-3, 2-4 1 & 4 2.5A / 125V
220 VAC 2-3 1 & 5 1.25A / 250V
230 VAC 2-3 1 & 4 1.25A / 250V
240 VAC 2-3 1 & 4 1.25A / 250V
+O
UT
+O
UT
-O
UT
-S
+S-S-O
UT
+S
AC Input +15V
41 235
-15V
OVP (OPTIONAL)
8.00" (203). 512" (13)
9.00" (229)AC INPUT/DC OUTPUT
°MTG HOLES (12 PLACES). 473" (12)
. 188"(4.8 )
. 75" (19)
4.87
"(124
)2.75
"( 70)
1.25
0"(32)
4.12
5"(105
)
1.250" (32)
.39"
(10)
. 75" (19)
MAX
.551" (14)
WEIGHT: 7. 5 LBS.(3.4 KG)
PEM NUT HOLES8-32 MTG (4 PLACES)
VR2V.ADJ
VR1I.LIM
VR3I.LIM
VR4V.ADJ
Case I3
General Specifications
Voltage/Current RatingsModel Number Output 1 Output 2
SLD-15-3030-15T +15V/3.0A1 -15V/3.0A1
1. Outputs are isolated from one another.
Operating Temperature Range 0 to +50oC (Derate to 40% at +70oC)
Temperature Coefficient (Typical) +/- 0.01% / oC
Stability Within +/- 0.05% (For 24 hours after warm-up)
Vibration Per MIL-STD-810C, Method 514
Shock Per MIL-STD-810C, Method 516
EMI/RFI Linear power supplies have inherently low conducted and radiated noise levels. For most system applications, these power supplies will meet the requirements of FCC Class “B” and VDE 0871 for Class “B” equipment without additional noise filtering.
Cooling Forced air. 20 CFM required for full rating Derate 30% for convection cooling.
Input SpecificationsMulti Input (all units) 100/120/220/230/240 VAC selectable +/- 10% except 230 VAC is +15%, -6%
Frequency Range 47-63 Hz (Typical is 60 Hz. Derate output 10% at 50 Hz)
Transient Response Time 50 µsec at 50% load change
Fuse Requirements Units are not fused internally. For safe operation, user must provide input line fuse as per values given in table.
Output Specifications
Line Regulation 0.05% for +/- 10% change
Load Regulation 0.05% for 50% change
Ripple 3.0 mV maximum peak-to-peak
DC Output Adjustment Range +/- 5% minimum
Overvoltage Protection OVP is optionally available
Remote Sensing Refer to Figure 1 for the output(s) with remote sensing.
Overload Protection 125 to 150% foldback current limit
Contact Technical Services at 1-800-377-4384 or [email protected] with any questions. Visit our website at www.solaheviduty.com
Contact Technical Services at 1-800-377-4384 or [email protected] with any questions. Visit our website at www.solaheviduty.com
*Note: Unit is shipped for 120V input from factory.
Application Note: User needs to provide earth ground to power supply with either solder to Tab or using washer and nut assembly. The SLD power supply is shipped from the factory with metal shorting straps connected between the + OUT and + S terminals and the (-) OUT and (-) S terminals. This strapping configuration allows the output of the SLS to be taken from either pair of terminals. This is the standard configuration. The remote sense feature is enabled by removing the shorting straps and connecting the individual OUT and S terminals to the appropriate points of the load. If an OVP circuit is used it should be connected to the + OUT and (-) OUT terminals. The OVP should never be connected to the + S, - S terminals without the use of the shorting straps. In all cases it is critical that the terminal screws be firmly tightened.
Note: The DC outputs can be adjusted with V. ADJ. I. LIM is factory set on all models and should not be adjusted by users.
• Easy installation with strip terminal• Tight regulation: 0.05% Line; 0.05% Load• Full Output Ratings to +50oC• OVP Option 15V• Foldback Current Limiting Overload Protection with
Automatic Recovery
• Multi-Tap AC Inputs• 100% Four-Hour Burn-in• Please see enclosed “Terms & Conditions and
Sales & Policies & Procedures”• UL Recognized• CSA Certified
+O
UT
+O
UT
-O
UT
-S
+S-S-O
UT
+S
AC Input +15V
41 235
-15V
OVP (OPTIONAL)
8.00" (203). 512" (13)
9.00" (229)AC INPUT/DC OUTPUT
°MTG HOLES (12 PLACES). 473" (12)
. 188"(4.8 )
. 75" (19)
4.87
"(124
)2.75
"( 70)
1.25
0"(32)
4.12
5"( 105
)
1.250" (32)
.39"
(10)
. 75" (19)
MAX
.551" (14)
WEIGHT: 7. 5 LBS.(3.4 KG)
PEM NUT HOLES8-32 MTG (4 PLACES)
VR2V.ADJ
VR1I.LIM
VR3I.LIM
VR4V.ADJ
Serie SL - Lineales de Salida Sencilla & Múltiple Manual de la Instrucción
Modelo: SLD-15-3030-15T
Características
Entrada AC Conexiones
Especificaciones
Contacte los Servicios Técnicos en 1-847-268-6000 o [email protected] con cualquiera preguntan. Visite nuestro sitio web en www.solaheviduty. com
Contacte los Servicios Técnicos en 1-847-268-6000 o [email protected] con cualquiera preguntan. Visite nuestro sitio web en www.solaheviduty. com
Para el uso en: Conecte Aplique AC a: El fusible primario
100 VAC 1-3, 2-4 1 & 5 2.5A / 125V
120 VAC* 1-3, 2-4 1 & 4 2.5A / 125V
220 VAC 2-3 1 & 5 1.25A / 250V
230 VAC 2-3 1 & 4 1.25A / 250V
240 VAC 2-3 1 & 4 1.25A / 250V
P/N A272-032 Rev. 3 (August 17, 2007)
Caja I3
* La nota: La unidad se envía para la entrada 120V de la fábrica.
Voltaje/Las Calificaciones ActualesNúmero de Catálogo Salida 1 Salida 2
SLD-15-3030-15T +15V/3.0 A1 -15V/3.0A1
1.Las salidas se aíslan del uno al otro.
Rango de Operación de Temperatura 0 to +50oC (Ajuste al 40% a +70oC)
Coeficiente de Temperatura (Típico) +/- 0.01% / oC
Estabilidad Después del calentamiento inicial, ±.5%
Vibración De acuerdo con MIL-STD-810C, Método 514
Golpes De acuerdo con MIL-STD-810C, Método 516
EMI/RFI Las fuentes de alimentación lineales tienen inherentemente bajos niveles de ruido conducido y radiado. Para la mayoría de las aplicaciones en sistemas estas cumplen con los requerimientos de FCC Clase B y VDE 0871 para Clase B.
Enfriamiento De aire forzado. 20 CFM requeridos para el grado completo reducen la capacidad normal del 30% para refrescarse de la convección.
EntradaVoltaje de Entrada 100/120/220/230/240 VAC selectable +/- 10% except 230 VAC is +15%, -6%
Frecuencia de Entrada 47-63 Hz (Típico es 60 Hz. La producción de Derate 10% en 50 Hz)
Tiempo de Respuesta a Transientes 50 µsec at 50% load change
Funda los Requisitos Las unidades no se funden internamente. Para la operación segura, el usuario debe proporcionar fusible de entrada de línea como por valores se rindió tabla.
SalidaRegulación de Línea 0.05% para un cambio del 10%
Regulación de la carga 0.05% para un cambio del 50%
Rizo 3.0 mV máximo Pico-a-Pico
Rango de Ajuste de CD de Salida +/- 5% Mínimo
Protección de Sobrevoltaje Todas las salidas de 5-Volt incluyen OVP integrada como un estándar (el ajuste es 6.2 V ±0.4 V) OVP está disponible opcionalmente en otros tipos
Presentir de telemando OVP is optionally available
Protección contra Sobrecarga 125 to 150% foldback automático de limitación de corriente
Sensores Remotos Todas unidades listaron tiene la capacidad de sensores remotos.
Dimensiones (pulg/mm)
La Nota de la aplicación: Las necesidades de Usuario a proporcionar la tierra el suelo para accionar el suministro con o soldadura qa la Etiqueta o utilizar arandela y asamblea de nuez. La planta SLD se envía de fábrica con bandas metálicas de cortocircuito conectadas entre los terminales + OUT (salida) y + S y los terminales (-) OUT y (-) S. Esta configuración de bandas permite la salida desde la SLS desde cualquier par de terminales, y es la configuración estándar. La función de sensor remoto se activa al retirar las bandas de cortocircuito y conectar los terminales individuales de salida (OUT) y S con los puntos pertinentes de la carga. Si se utiliza un circuito OVP, deberá conectarse con los terminales + OUT y (-) OUT. El circuito OVP no debe conectarse nunca con los terminales + S, - S sin las bandas de cortocircuito. En todos los casos es esencial ajustar los tornillos del terminal firmemente.
La nota: La salida de la C.C. se puede ajustar con el ajuste del V. ADJ. I. LIM ha sido fijada en la fabrica y no se debe ajustar por los usuarios.
• Terminales de conexión fáciles de instalar. • Tight regulation: 0.05% Line; 0.05% Load• Las calificaciones de salida a +50oC• OVP Option 15V• Foldback Current Limiting Protección contra
Sobrecarga con Automático Recupera
• Multi-Tap AC Las Entradas• 100% Cuatro Hora Burn-in• Sírvase consultar “Términos y Condiciones, y
Políticas y Procedimientos de Ventas”• UL Reconocido• CSA Certificado
• Your load is now protected against an overvoltage condition that could destroy the load.
• Should you experience a situation where the OVP triggers, remove input power! Check for any failures.
• If the input fuse to the supply is blown, it is a good indication that there is a failure to the power supply itself.
If you find that there is no failure, re-energize the supply. If the supply voltage returns to nominal, the power supply and OVP will be ready for another OVP situation. This is called a nuisance trip. It is not uncommon and does not indicate a failure of the OVP module. Instead, it has done its job and protected your circuit. Nuisance tripping is generally caused by voltage spikes created by the load. If it continually occurs, check your load for noise generating conditions and correct them.
Under all conditions, removal of input power is necessary to reset the OVP.
Silver Line Overvoltage: Protection Option (OVP)
Model:SLO-12-000-1Instruction Manual
Features• For use with 5 to 28V outputs• Full Ratings to +50oC• Please see enclosed “Terms & Conditions and Sales & Policies & Procedures”
Maximum Current Rating
ModelIntermittent
RatingContinuous
RatingSLO-12-000-1 12 Amps 8 Amps
Output Voltage Recommended Trigger Voltages5 6.2+/-0.4
12 14
15 17
24 27
DUAL+/-12 27
DUAL+/-15 33
Contact Technical Services at 1-800-377-4384 or [email protected] with any questions. Visit our website at www.solaheviduty.com
Mechanical Dimensions: inches (mm)
Case J1
This unit is to be used on any Sola Silver Line Linear Power Supply where there is no factory provided Overvoltage Protection (OVP) built into the output. (Generally, all +/-5V outputs come with built-in OVP). These OVPs can be used on any power supply with built-in overload/short circuit protection that will not allow the current to exceed the maximum current rating of this OVP. Please note that only the Silver Line of Sola Power Supplies have mounting holes designed for these OVPs.
The above table indicates Sola’s recommended trigger voltage set point for different output voltages. Where +/-Outputs exist with a common terminal, a single OVP module located across the positive (+) and negative (-) terminals will provide functional OVP for both individual outputs.
The OVP module comes complete with mounting hardware and hookup leads. To connect the OVP to your Silver Line Series Power Supply, see your Power Supply User’s Manual for the recommended placement. Attach the black lead to the negative (-) terminal of the supply and the white lead to the positive (+) terminal. Make sure to check that the positive (+) and negative (-) leads of the supply are connected to the (+) and (-) leads of the OVP module. Rotate the potentiometer (R1) on the OVP module completely clockwise. Without your load(s) connected, apply power, then adjust the output voltage on the supply. Adjust to the level at which you wish the OVP to trigger. Slowly adjust (R1) on the OVP module counter clockwise until the output of the supply drops suddenly. Remove the input power to the supply and back the potentiometer (R1) on the OVP module slightly clockwise. Re-energize the supply and adjust the output voltage to the nominal voltage rating. The OVP trip level is now set. You may wish to set the OVP potentiometer in place with an electrical grade varnish such as glyptol.
Contact Technical Services at 1-800-377-4384 or [email protected] with any questions. Visit our website at www.solaheviduty.com
1.55” (39.37)
.58” (14.7)
.56”
(14.
2)
.22” (5.6)
.75” (19)
THREADED INSERTS2 PLACESMOUNTING SCREWSINCLUDED.
1.50
” (3
8.1)
OVP ADJ.
Reenergice la fuente de alimentación y ajuste el voltaje de salida a la capacidad nominal de voltaje. El nivel de disparo de la OVP ahora está establecido. Quizá desee fijar en posición el potenciómetro del OVP con un esmalte de grado eléctrico, como glyptol.• Su carga ahora está protegida contra una condición de sobretensión que podría destruir la carga.• Si experimenta una situación donde la OVP se dispara, ¡corte la alimentación eléctrica de entrada!
Revise para ver si hay averías.• Si el fusible de entrada para la fuente de alimentación está quemado, es una buena indicación que la
fuente de alimentación eléctrica en sí está averiada.
Si no descubre ningún fallo o avería, reenergice la fuente de alimentación eléctrica. Si el voltaje de suministro regresa al valor nominal, la fuente de alimentación eléctrica y la OVP estarán listas para otra situación de OVP. Esto se conoce como un disparo injustificado. Este tipo de disparo no es raro y no indica un fallo o avería del módulo OVP. Más bien, ha funcionado como debe ser y ha protegido su circuito. Los disparos injustificados generalmente son causados por los picos de tensión creados por la carga. Si suceden continuamente, vea si hay condiciones de generación de ruido presentes en su carga y corríjalas.
Bajo toda condición, es necesario cortar la alimentación eléctrica de entrada para reponer la OVP.
Opción de Protección contra Sobretensiones (OVP) para la Línea Silver
Modelo: SLO-12-000-1Manual de Instrucciones
Características• Para uso con salidas de 5 a 28V• Cargas plenas hasta +50°C• Sírvase consultar “Términos y Condiciones, y Políticas y Procedimientos de Ventas”
Grado Actual Máximo
Modelo Grado Intermitente Continuo Grado
SLO-12-000-1 12 Amps 8 Amps
Voltaje De la Salida Voltajes De Disparador Recomendados5 6.2+/-0.4
12 14
15 17
24 27
DUAL+/-12 27
DUAL+/-15 33
Contacte los Servicios Técnicos en 1-847-268-6000 o [email protected] con cualquiera preguntan. Visite nuestro sitio web en www.solaheviduty. com
Esta unidad es para uso con cualquier Fuente de Alimentación Eléctrica Lineal de la Línea Silver Sola que carezca de toda Protección contra Sobretensiones (OVP) incorporada en la salida suministrada de fábrica. (Generalmente, todas las salidas de +/-5V se suministran con la OVP incorporada). Estas OVP pueden utilizarse en cualquier fuente de alimentación eléctrica con protección incorporada contra sobrecargas y cortocircuitos, que impedirá que la corriente exceda la máxima capacidad de corriente de esta OVP. Por favor observe que sólo las unidades de la Línea Silver de Fuentes de Alimentación Eléctrica Sola tienen orificios de montaje diseñados para estas OVP.
La tabla que se muestra arriba indica los voltajes de disparo recomendados por Sola para los diferentes voltajes de salida. Donde hayan Salidas+/- a través de una terminal común, un módulo OVP individual situado entre las terminales positiva (+) y negativa (-) proporcionará la función de protección contra sobretensiones (OVP) para ambas salidas individuales.
El módulo OVP se suministra completo con los herrajes de montaje y los conductores de conexión. Para conectar la OVP a su Fuente de Alimentación Eléctrica de la Serie Línea Silver, consulte el Manual del Usuario de su Fuente de Alimentación Eléctrica para ver cuál es el lugar de instalación recomendado. Conecte el conductor negro en la terminal negativa (-) de la fuente y el conductor blanco en la terminal positiva (+). Asegúrese de comprobar que los conductores positivo (+) y negativo (-) de la fuente están conectados a los conductores (+) y (-) del módulo OVP. Gire el potenciómetro (R1) en el módulo OVP completamente en el sentido de las agujas del reloj (hacia la derecha). Sin ninguna carga conectada, conecte la alimentación eléctrica, luego ajuste el voltaje de salida de la fuente de alimentación eléctrica. Ajuste al nivel al cual usted desea que la OVP se dispare. Ajuste lentamente (R1) en el módulo OVP en sentido contrario a las agujas del reloj hasta que la salida de la fuente de alimentación eléctrica caiga repentinamente. Corte la alimentación de entrada para la fuente de alimentación y gire ligeramente hacia la derecha (o en el sentido de las agujas del reloj) el potenciómetro (R1) en el módulo OVP.
Contacte los Servicios Técnicos en 1-847-268-6000 o [email protected] con cualquiera preguntan. Visite nuestro sitio web en www.solaheviduty. com
Dimensiones Mecánicas: pulgadas (milímetro)
Caja J1
1.55” (39.37)
.58” (14.7)
.56”
(14.
2)
.22” (5.6)
.75” (19)
RELLENOS ROSCADOS 2 LUGARES. TORNILLOS DE MONTAJE INCLUIDOS
1.50
” (3
8.1)
OVP ADJ.
P/N A272-017 Rev. 4 (August 17, 2007)
• Your load is now protected against an overvoltage condition that could destroy the load.
• Should you experience a situation where the OVP triggers, remove input power! Check for any failures.
• If the input fuse to the supply is blown, it is a good indication that there is a failure to the power supply itself.
If you find that there is no failure, re-energize the supply. If the supply voltage returns to nominal, the power supply and OVP will be ready for another OVP situation. This is called a nuisance trip. It is not uncommon and does not indicate a failure of the OVP module. Instead, it has done its job and protected your circuit. Nuisance tripping is generally caused by voltage spikes created by the load. If it continually occurs, check your load for noise generating conditions and correct them.
Under all conditions, removal of input power is necessary to reset the OVP.
Silver Line Overvoltage: Protection Option (OVP)
Model:SLO-12-000-TBInstruction Manual
Features• For use with 5 to 28V outputs• Full Ratings to +50oC• Please see enclosed “Terms & Conditions and Sales & Policies & Procedures”
Maximum Current Rating
ModelIntermittent
RatingContinuous
RatingSLO-12-000-TB 12 Amps 8 Amps
Output Voltage Recommended Trigger Voltages5 6.2+/-0.4
12 14
15 17
24 27
DUAL+/-12 27
DUAL+/-15 33
Contact Technical Services at 1-800-377-4384 or [email protected] with any questions. Visit our website at www.solaheviduty.com
Mechanical Dimensions: inches (mm)
This unit is to be used on any Sola Silver Line Linear Power Supply where there is no factory provided Overvoltage Protection (OVP) built into the output. (Generally, all +/-5V outputs come with built-in OVP). These OVPs can be used on any power supply with built-in overload/short circuit protection that will not allow the current to exceed the maximum current rating of this OVP. Please note that only the Silver Line of Sola Power Supplies have mounting holes designed for these OVPs.
The above table indicates Sola’s recommended trigger voltage set point for different output voltages. Where +/-Outputs exist with a common terminal, a single OVP module located across the positive (+) and negative (-) terminals will provide functional OVP for both individual outputs.
The OVP module comes complete with mounting hardware and hookup leads. To connect the OVP to your Silver Line Series Power Supply, see your Power Supply User’s Manual for the recommended placement. Attach the black lead to the negative (-) terminal of the supply and the white lead to the positive (+) terminal. Make sure to check the positive (+) and negative (-) leads of the supply are connected to the (+) and (-) leads of the OVP module. Rotate the potentiometer (R1) on the OVP module completely counter clockwise. Without your load(s) connected, apply power, then adjust the output voltage on the supply. Adjust to the level at which you wish the OVP to trigger. Slowly adjust (R1) on the OVP module clockwise until the output of the supply drops suddenly. Remove the input power to the supply and back the potentiometer (R1) on the OVP module slightly counter clockwise. Re-energize the supply and adjust the output voltage to the nominal voltage rating. The OVP trip level is now set. You may wish to set the OVP potentiometer in place with an electrical grade varnish such as glyptol.
Contact Technical Services at 1-800-377-4384 or [email protected] with any questions. Visit our website at www.solaheviduty.com
Case J2
.22” (5.5)
.984” (25)
.40” (10)
.19” (5.0) THREADED INSERTS2 PLACES.MOUNTING SCREWSINCLUDED
.57”
(14.
5)
1.57
” (4
0)
OVPADJ.
Reenergice la fuente de alimentación y ajuste el voltaje de salida a la capacidad nominal de voltaje. El nivel de disparo de la OVP ahora está establecido. Quizá desee fijar en posición el potenciómetro del OVP con un esmalte de grado eléctrico, como glyptol.• Su carga ahora está protegida contra una condición de sobretensión que podría destruir la carga.• Si experimenta una situación donde la OVP se dispara, ¡corte la alimentación eléctrica de entrada!
Revise para ver si hay averías.• Si el fusible de entrada para la fuente de alimentación está quemado, es una buena indicación que la
fuente de alimentación eléctrica en sí está averiada.
Si no descubre ningún fallo o avería, reenergice la fuente de alimentación eléctrica. Si el voltaje de suministro regresa al valor nominal, la fuente de alimentación eléctrica y la OVP estarán listas para otra situación de OVP. Esto se conoce como un disparo injustificado. Este tipo de disparo no es raro y no indica un fallo o avería del módulo OVP. Más bien, ha funcionado como debe ser y ha protegido su circuito. Los disparos injustificados generalmente son causados por los picos de tensión creados por la carga. Si suceden continuamente, vea si hay condiciones de generación de ruido presentes en su carga y corríjalas.
Bajo toda condición, es necesario cortar la alimentación eléctrica de entrada para reponer la OVP.
Opción de Protección contra Sobretensiones (OVP) para la Línea Silver
Modelo: SLO-12-000-TBManual de Instrucciones
Características• Para uso con salidas de 5 a 28V• Plenas cargas hasta +50ºC• Sírvase consultar “Términos y Condiciones, y Políticas y Procedimientos de Ventas”
Grado Actual Máximo
Modelo Grado Intermitente Continuo Grado
SLO-12-000-TB 12 Amps 8 Amps
Voltaje De la Salida Voltajes De Disparador Recomendados
5 6.2+/-0.4
12 14
15 17
24 27
DUAL+/-12 27
DUAL+/-15 33
Contacte los Servicios Técnicos en 1-847-268-6000 o [email protected] con cualquiera preguntan. Visite nuestro sitio web en www.solaheviduty. com
Esta unidad es para uso con cualquier Fuente de Alimentación Eléctrica Lineal de la Línea Silver Sola que carezca de toda Protección contra Sobretensiones (OVP) incorporada en la salida suministrada de fábrica. (Generalmente, todas las salidas de +/-5V se suministran con la OVP incorporada). Estas OVP pueden utilizarse en cualquier fuente de alimentación eléctrica con protección incorporada contra sobrecargas y cortocircuitos, que impedirá que la corriente exceda la máxima capacidad de corriente de esta OVP. Por favor observe que sólo las unidades de la Línea Silver de Fuentes de Alimentación Eléctrica Sola tienen orificios de montaje diseñados para estas OVP.
La tabla que se muestra arriba indica los voltajes de disparo recomendados por Sola para los diferentes voltajes de salida. Donde hayan Salidas+/- a través de una terminal común, un módulo OVP individual situado entre las terminales positiva (+) y negativa (-) proporcionará la función de protección contra sobretensiones (OVP) para ambas salidas individuales.
El módulo OVP se suministra completo con los herrajes de montaje y los conductores de conexión. Para conectar la OVP a su Fuente de Alimentación Eléctrica de la Serie Línea Silver, consulte el Manual del Usuario de su Fuente de Alimentación Eléctrica para ver cuál es el lugar de instalación recomendado. Conecte el conductor negro en la terminal negativa (-) de la fuente y el conductor blanco en la terminal positiva (+). Asegúrese de comprobar que los conductores positivo (+) y negativo (-) de la fuente están conectados a los conductores (+) y (-) del módulo OVP. Gire el potenciómetro (R1) en el módulo OVP completamente en sentido contrario a las agujas del reloj (hacia la izquierda). Sin ninguna carga conectada, conecte la alimentación eléctrica, luego ajuste el voltaje de salida de la fuente de alimentación eléctrica. Ajuste al nivel al cual usted desea que la OVP se dispare. Ajuste lentamente (R1) en el módulo OVP en el sentido de las agujas del reloj hasta que la salida de la fuente de alimentación eléctrica caiga repentinamente. Corte la alimentación de entrada para la fuente de alimentación y gire ligeramente hacia la izquierda (o en sentido contrario a las agujas del reloj) el potenciómetro (R1) en el módulo OVP.
P/N A272-018 Rev. 5 (November 1, 2007)
Contacte los Servicios Técnicos en 1-847-268-6000 o [email protected] con cualquiera preguntan. Visite nuestro sitio web en www.solaheviduty. com
Dimensiones Mecánicas: pulgadas (milímetro)
Caja J2
.22” (5.5)
.984” (25)
.40” (10)
.19” (5.0) RELLENOS ROSCADOS 2 LUGARES. TORNILLOS DE MONTAJE INCLUIDOS
.57”
(14.
5)
1.57
” (4
0)
OVPADJ.
Linear Open Frame DC Power SuppliesSilver Line Instruction Manual
Models: SLS-05-030-1T, SLS-12-017T, SLS-24-012T
Features
General Specifications
Voltage/Current Ratings
Model Number Output
SLS-05-030-1T 5V/3.0A
SLS-12-017T +12V/1.7A or +15V/1.5A
SLS-24-012T +24V/1.2A
Operating Temperature Range 0 to +50oC (Derate to 40% at +70oC)
Temperature Coefficient (Typical) +/- 0.01% / oC
Stability Within +/- 0.05% (24 hours after warm-up)
Vibration Per MIL-STD-810C, Method 514
Shock Per MIL-STD-810C, Method 516
EMI/RFI
Linear power supplies have inherently low conducted and radiated noise levels. For most system applications, these power supplies will meet the requirements of FCC Class “B” and VDE 0871 for Class “B” equipment without additional noise filtering.
Cooling Forced air. 20 CFM required for full rating Derate 30% for convection cooling.
Input Specifications
Multi Input (all units) 100/120/220/230/240 VAC selectable +/- 10% except 230 VAC is +15%, -6%
Frequency Range 47-63 Hz (Typical is 60 Hz. Derate output 10% at 50 Hz)
Transient Response Time50 µsec at 50% load changes for outputs rated up to 6A
100 µsec at 50% load changes for outputs rated 6A and over
Fuse Requirements Units are not fused internally. For safe operation, user must provide input line fuse as per values given in table.
Output Specifications
Line Regulation 0.05% for +/- 10% change
Load Regulation 0.05% for 50% change
Ripple 3.0 mV maximum peak-to-peak
DC Output Adjustment Range +/- 5% minimum
Overvoltage Protection All 5 volt outputs include built-in OVP as standard (setting is 6.2V +/- 0.4V). OVP is optionally available on other outputs
Remote Sensing All units listed have remote sensing capability.
Overload Protection 125 to 150% foldback current limit
Contact Technical Services at 1-800-377-4384 or [email protected] with any questions. Visit our website at www.solaheviduty.com
InstallationStep 1: Check the input AC connections
Step 2: Connect the AC input according to table below.
Note: SLS-12-017T can be set to a +12V to +15V range by adjusting R9 V. ADJ.
Contact Technical Services at 1-800-377-4384 or [email protected] with any questions. Visit our website at www.solaheviduty.com
Input AC Connections (See Case A)
Mechanical Dimensions: Inches (mm)
For use at: Connect Apply AC to: Primary Fuse Primary Fuse
SLS-05-030-1T SLS-12-017TSLS-24-012T
100 VAC 1-3, 2-4 1 & 5 0.5A / 125V 1.0A / 125V
120 VAC* 1-3, 2-4 1 & 4 0.5A / 125V 1.0A / 125V
220 VAC 2-3 1 & 5 0.25A / 250V 0.5A / 250V
230 VAC 2-3 1 & 4 0.25A / 250V 0.5A / 250V
240 VAC 2-3 1 & 4 0.25A / 250V 0.5A / 250V
Case A Note: The SLS models DC output can be adjusted with R9 V. ADJ.
R7 I. LIM is factory set and should not be adjusted by users.
.744" (18.9)
. 450" (11.5) MAX
0.188"(4.8 )
4.843" (123)
4.142" (105.2) 0.48" (12.2)
1.62" (41)
° MTG HOLES (6 PLACES)
AC INPUT/DC OUTPUT
OVP(OPTIONAL )
.744
"(1
8.9)
.58"
(14-
8)
.378
"(9
.6)3.
992"
( 101
.4)
3.37
0"(8
5.6)
4
+S 1 235-OU
T-S+O
UT
WEIGH T: 2.43 L BS.(1.1 KG )
PEM NUT HOLE S 6-32 MT G ( 4 P LACES)
R7I-LIM ADJ
R9V. ADJ
*Note: Unit is shipped for 120V input from factory.
Application Note: User needs to provide earth ground to power supply with either solder to Tab or using washer and nut assembly. The SLS power supply is shipped from the factory with metal shorting straps connected between the + OUT and + S terminals and the (-) OUT and (-) S terminals. This strapping configuration allows the output of the SLS to be taken from either pair of terminals. This is the standard configuration. The remote sense feature is enabled by removing the shorting straps and connecting the individual OUT and S terminals to the appropriate points of the load. If an OVP circuit is used it should be connected to the + OUT and (-) OUT terminals. The OVP should never be connected to the + S, - S terminals without the use of the shorting straps. In all cases it is critical that the terminal screws be firmly tightened.
• Easy installation with strip terminal• Adjustable output• Tight regulation: 0.05% Line; 0.05% Load• Full Output Ratings to +50oC• Built in OVP on 5 Volt Outputs• OVP Option for 12V, 15V and 24V• Foldback Current Limiting Overload Protection with
Automatic Recovery
• Multi-Tap AC Inputs• 100% Four-Hour Burn-in• Please see enclosed “Terms & Conditions and
Sales & Policies & Procedures”• UL Recognized• CSA Certified• CE Marked• CB Certified
Contacte los Servicios Técnicos en 1-847-268-6000 o [email protected] con cualquiera preguntan. Visite nuestro sitio web en www.solaheviduty. com
Contacte los Servicios Técnicos en 1-847-268-6000 o [email protected] con cualquiera preguntan. Visite nuestro sitio web en www.solaheviduty. com
Serie SL - Lineales de Salida Sencilla & Múltiple Manual de la Instrucción
Modelos: SLS-05-030-1T, SLS-12-017T, SLS-24-012T
Características
Especificaciones
InstalaciónDé un paso 1: Verifica las conexiones de entrada de C.A.
Dé un paso 2: Conecte a la entrada de C.A. según posponer abajo.
La nota: SLS-12-017T se puede establecer en el rango +12V to +15V ajustando R9 V. ADJ.
P/N A272-022 Rev. 4 (August 16, 2007)
Entrada AC Conexiones (See Caja A)
Caja A La nota: La salida DC de los modelos SLS puede ser ajustada con el R9 V. ADJ
R7 I. LIM ha sido fijada en la fabrica y no se debe ajustar por los usuarios.
.744" (18.9)
. 450" (11.5) MAX
0.188"(4.8 )
4.843" (123)
4.142" (105.2) 0.48" (12.2)
1.62" (41)
° MTG HOLES (6 PLACES)
AC INPUT/DC OUTPUT
OVP(OPTIONAL )
.744
"(1
8.9)
.58"
(14-
8)
.378
"(9
.6)3.
992"
( 101
.4)
3.37
0"(8
5.6)
4
+S 1 235-OU
T-S+O
UT
WEIGH T: 2.43 L BS.(1.1 KG )
PEM NUT HOLE S 6-32 MT G ( 4 P LACES)
R7I-LIM ADJ
R9V. ADJ
Para el uso en: Conecte Aplique AC a: El fusible primario El fusible primario
SLS-05-030-1T SLS-12-017TSLS-24-012T
100 VAC 1-3, 2-4 1 & 5 0.5A / 125V 1.0A / 125V
120 VAC* 1-3, 2-4 1 & 4 0.5A / 125V 1.0A / 125V
220 VAC 2-3 1 & 5 0.25A / 250V 0.5A / 250V
230 VAC 2-3 1 & 4 0.25A / 250V 0.5A / 250V
240 VAC 2-3 1 & 4 0.25A / 250V 0.5A / 250V
* La nota: La unidad se envía para la entrada 120V de la fábrica.
La Nota de la aplicación: Las necesidades de Usuario a proporcionar la tierra el suelo para accionar el suministro con o soldadura qa la Etiqueta o utilizar arandela y asamblea de nuez. La planta SLS se envía de fábrica con bandas metálicas de cortocircuito conectadas entre los terminales + OUT (salida) y + S y los terminales (-) OUT y (-) S. Esta configuración de bandas permite la salida desde la SLS desde cualquier par de terminales, y es la configuración estándar. La función de sensor remoto se activa al retirar las bandas de cortocircuito y conectar los terminales individuales de salida (OUT) y S con los puntos pertinentes de la carga. Si se utiliza un circuito OVP, deberá conectarse con los terminales + OUT y (-) OUT. El circuito OVP no debe conectarse nunca con los terminales + S, - S sin las bandas de cortocircuito. En todos los casos es esencial ajustar los tornillos del terminal firmemente.
Dimensiones (pulg/mm)
Voltaje/Las Calificaciones ActualesNúmero de Catálogo Salida
SLS-05-030-1T 5V/3.0A
SLS-12-017T +12V/1.7A or +15V/1.5A
SLS-24-012T +24V/1.2A
Rango de Operación de Temperatura 0 to +50oC (Ajuste al 40% a +70oC)
Coeficiente de Temperatura (Típico) +/- 0.01% / oC
Estabilidad Dentro de +/- 0.05% (24 horas después del calentamiento)
Vibración De acuerdo con MIL-STD-810C, Método 514
Golpes De acuerdo con MIL-STD-810C, Método 516
EMI/RFILas fuentes de alimentación lineales tienen inherentemente bajos niveles de ruido conducido y radiado. Para la mayoría de las aplicaciones en sistemas estas cumplen con los requerimientos de FCC Clase B y VDE 0871 para Clase B.
Enfriamiento De aire forzado. 20 CFM requeridos para el grado completo reducen la capacidad normal del 30% para refrescarse de la convección.
EntradaVoltaje de Entrada 100/120/220/230/240 VAC selectable +/- 10% except 230 VAC is +15%, -6%
Frecuencia de Entrada 47-63 Hz (Típico es 60 Hz. La producción de Derate 10% en 50 Hz)
Tiempo de Respuesta a Transientes50 µsec en 50% la carga cambia para producciones valoradas hasta 6A.
100 µsec en 50% la carga cambia para producciones valoradas 6A y sobre.
Funda los RequisitosLas unidades no se funden internamente. Para la operación segura, el usuario debe proporcionar fusible de entrada de línea como por valores se rindió tabla.
SalidaRegulación de Línea 0.05% para un cambio del 10%
Regulación de la carga 0.05% para un cambio del 50%
Rizo 3.0 mV máximo Pico-a-Pico
Rango de Ajuste de CD de Salida +/- 5% Mínimo
Protección de Sobrevoltaje Las salidas de 5 voltios incluyen OVP incorporado como estándar (el ajuste es 6.2V +/- 0.4V). OVP está opcionalmente disponible en otras salidas
Protección contra Sobrecarga 125 to 150% foldback automático de limitación de corriente
Sensores Remotos Todas unidades listaron tiene la capacidad de sensores remotos.
• Terminales de conexión fáciles de instalar. • De salida ajustable• Tight regulation: 0.05% Line; 0.05% Load• Las calificaciones de salida a +50oC• OVP integrada en modelos de 5 V y opcional en los
modelos de 12, 15 y 24 V. • Foldback Current Limiting Protección contra
Sobrecarga con Automático Recupera
• Multi-Tap AC Las Entradas• 100% Cuatro Hora Burn-in• Sírvase consultar “Términos y Condiciones, y
Políticas y Procedimientos de Ventas” adjunto.• Reconocido por UL • Certificado CSA • Aprovado en CE • Certificado CB
Linear Open Frame DC Power SuppliesSilver Line Instruction Manual
Models: SLS-05-060-1T, SLS-12-034T, SLS-24-024T
Features
Input AC Connections (See Case B)
For use at: Connect Apply AC to:
Primary Fuse(SLS-05-0601T)(SLS-12-034T)(SLS-24-024T)
100 VAC 1-3, 2-4 1 & 5 1.6A / 125V
120 VAC* 1-3, 2-4 1 & 4 1.6A / 125V
220 VAC 2-3 1 & 5 0.8A / 250V
230 VAC 2-3 1 & 4 0.8A / 250V
240 VAC 2-3 1 & 4 0.8A / 250VGeneral Specifications
Voltage/Current RatingsModel Number Output
SLS-05-060-1T +5V / 6.0 A
SLS-12-034-T +12V / 3.4 A
SLS-24-024-T +24V / 2.4 A
Operating Temperature Range 0 to +50oC (Derate to 40% at +70oC)
Temperature Coefficient (Typical) +/- 0.01% / oC
Stability Within +/- 0.05% (24 hours after warm-up)
Vibration Per MIL-STD-810C, Method 514
Shock Per MIL-STD-810C, Method 516
EMI/RFI
Linear power supplies have inherently low conducted and radiated noise levels. For most system applications, these power supplies will meet the requirements of FCC Class “B” and VDE 0871 for Class “B” equipment without additional noise filtering.
Cooling Forced air. 20 CFM required for full rating Derate 30% for convection cooling.
Input SpecificationsMulti Input (all units) 100/120/220/230/240 VAC selectable +/- 10% except 230 VAC is +15%, -6%
Frequency Range 47-63 Hz (Typical is 60 Hz. Derate output 10% at 50 Hz)
Transient Response Time 50 µsec at 50% load changes for outputs rated up to 6A
Fuse Requirements Units are not fused internally. For safe operation, user must provide input line fuse as per values given in table.
Output Specifications
Line Regulation 0.05% for +/- 10% change
Load Regulation 0.05% for 50% change
Ripple 3.0 mV maximum peak-to-peak
DC Output Adjustment Range +/- 5% minimum
Overvoltage Protection All 5 volt outputs include built-in OVP as standard (setting is 6.2 V +/- 0.4 V). OVP is optionally available on other outputs.
Remote Sensing All units listed have remote sensing capability.
Overload Protection 125 to 150% foldback current limit
Contact Technical Services at 1-800-377-4384 or [email protected] with any questions. Visit our website at www.solaheviduty.com
Contact Technical Services at 1-800-377-4384 or [email protected] with any questions. Visit our website at www.solaheviduty.com
Mechanical Dimensions: inches (mm)
Case BUse Case B1 Output Configuration for SLS-05-060-1T and SLS-12-034T.
Use Case B2 Output Configuration for SLS-24-024T.
Note: The SLS models DC output can be adjusted with R10 V. ADJ. R8 I. LIM is factory set and should not be adjusted by users.
0.72" (18.3)
4.87" (123.5)
4.118" (104.6)
0.188"(4.8)
2.5
0"
(62
.8)
1.2
8"
(32
.5)
° MTG HOLES (8 PLACES )
0.433" (11)
5.6
2"
(14
2.6
)
0.252” (6.4)
4.8
75
"(1
24
)
AC
INP
UT
/D
CO
UT
PU
TO
VP
(OP
TIO
NA
L)
0.72" (18.3)
1.28" (32.5)
MAX
.450" (11.5)
.39"(10)
4
1
23
5
-S
+OUT+S
-OUT
WEIGHT: 4 LBS.(1.8 )KG
PEM NUT HOLES6-32 MTG (4 PLACES)
4
1
23
5
+S
-OUT-S
+OUT
CASE B1
CASE B2
R10 V.ADJ
R8 I.LIM
Application Note: User needs to provide earth ground to power supply with either solder to Tab or using washer and nut assembly. The SLS power supply is shipped from the factory with metal shorting straps connected between the + OUT and + S terminals and the (-) OUT and (-) S terminals. This strapping configuration allows the output of the SLS to be taken from either pair of terminals. This is the standard configuration. The remote sense feature is enabled by removing the shorting straps and connecting the individual OUT and S terminals to the appropriate points of the load. If an OVP circuit is used it should be connected to the + OUT and (-) OUT terminals. The OVP should never be connected to the + S, - S terminals without the use of the shorting straps. In all cases it is critical that the terminal screws be firmly tightened.
*Note: Unit is shipped for 120V input from factory.
• Easy installation with strip terminal• Tight regulation: 0.05% Line; 0.05% Load• Full Output Ratings to +50oC• Built in OVP on 5 Volt Outputs• OVP Option for 12V and 24V• Foldback Current Limiting Overload Protection with
Automatic Recovery
• Multi-Tap AC Inputs• 100% Four-Hour Burn-in• Please see enclosed “Terms & Conditions and
Sales & Policies & Procedures”• UL Recognized• CSA Certified• CE Marked• CB Certified
Serie SL - Lineales de Salida Sencilla & Múltiple Manual de la Instrucción
Modelos: SLS-05-060-1T, SLS-12-034T, SLS-24-024T
Características
Entrada AC Conexiones (See Caja B)
Especificaciones
Para el uso en: Conecte Aplique AC a:
El fusible primario(SLS-05-0601T)(SLS-12-034T)(SLS-24-024T)
100 VAC 1-3, 2-4 1 & 5 1.6A / 125V
120 VAC* 1-3, 2-4 1 & 4 1.6A / 125V
220 VAC 2-3 1 & 5 0.8A / 250V
230 VAC 2-3 1 & 4 0.8A / 250V
240 VAC 2-3 1 & 4 0.8A / 250V
Contacte los Servicios Técnicos en 1-847-268-6000 o [email protected] con cualquiera preguntan. Visite nuestro sitio web en www.solaheviduty. com
Contacte los Servicios Técnicos en 1-847-268-6000 o [email protected] con cualquiera preguntan. Visite nuestro sitio web en www.solaheviduty. com
P/N A272-023 Rev. 3 (August 16, 2007)
* La nota: La unidad se envia para la entrada 120V de la fábrica.
Caja BUtilice la configuración de salida del caso B1 para SLS-05-060-1T y SLS-12-034T.
Utilice la configuración de salida del caso B2 para SLS-24-024T.
La nota: La salida DC de los modelos SLS puede ser ajustada con el R10 V. ADJ R8 I. LIM ha sido fijada en la fabrica y no se debe ajustar por los usuarios.
0.72" (18.3)
4.87" (123.5)
4.118" (104.6)
0.188"(4.8)
2.5
0"
(62
.8)
1.2
8"
(32
.5)
° MTG HOLES (8 PLACES )
0.433" (11)
5.6
2"
(14
2.6
)
0.252” (6.4)
4.8
75
"(1
24
)
AC
INP
UT
/D
CO
UT
PU
TO
VP
(OP
TIO
NA
L)
0.72" (18.3)
1.28" (32.5)
MAX
.450" (11.5)
.39"(10)
4
1
23
5
-S
+OUT+S
-OUT
WEIGHT: 4 LBS.(1.8 )KG
PEM NUT HOLES6-32 MTG (4 PLACES)
4
1
23
5
+S
-OUT-S
+OUT
CASE B1
CASE B2
R10 V.ADJ
R8 I.LIM
La Nota de la aplicación: Las necesidades de Usuario a proporcionar la tierra el suelo para accionar el suministro con o soldadura qa la Etiqueta o utilizar arandela y asamblea de nuez. La planta SLS se envía de fábrica con bandas metálicas de cortocircuito conectadas entre los terminales + OUT (salida) y + S y los terminales (-) OUT y (-) S. Esta configuración de bandas permite la salida desde la SLS desde cualquier par de terminales, y es la configuración estándar. La función de sensor remoto se activa al retirar las bandas de cortocircuito y conectar los terminales individuales de salida (OUT) y S con los puntos pertinentes de la carga. Si se utiliza un circuito OVP, deberá conectarse con los terminales + OUT y (-) OUT. El circuito OVP no debe conectarse nunca con los terminales + S, - S sin las bandas de cortocircuito. En todos los casos es esencial ajustar los tornillos del terminal firmemente.
Dimensiones (pulg/mm)Voltaje/Las Calificaciones ActualesNúmero de Catálogo Salida
SLS-05-060-1T +5V / 6.0 A
SLS-12-034-T +12V / 3.4 A
SLS-24-024-T +24V / 2.4 A
Rango de Operación de Temperatura 0 to +50oC (Ajuste al 40% a +70oC)
Coeficiente de Temperatura (Típico) +/- 0.01% / oC
Estabilidad Dentro de +/- 0.05% (24 horas después del calentamiento)
Vibración De acuerdo con MIL-STD-810C, Método 514
Golpes De acuerdo con MIL-STD-810C, Método 516
EMI/RFILas fuentes de alimentación lineales tienen inherentemente bajos niveles de ruido conducido y radiado. Para la mayoría de las aplicaciones en sistemas estas cumplen con los requerimientos de FCC Clase B y VDE 0871 para Clase B.
Enfriamiento De aire forzado. 20 CFM requeridos para el grado completo reducen la capacidad normal del 30% para refrescarse de la convección.
EntradaVoltaje de Entrada 100/120/220/230/240 VAC selectable +/- 10% except 230 VAC is +15%, -6%
Frecuencia de Entrada 47-63 Hz (Típico es 60 Hz. La producción de Derate 10% en 50 Hz)
Tiempo de Respuesta a Transientes 50 µsec en 50% la carga cambia para producciones valoradas hasta 6A.
Funda los RequisitosLas unidades no se funden internamente. Para la operación segura, el usuario debe proporcionar fusible de entrada de línea como por valores se rindió tabla.
SalidaRegulación de Línea 0.05% para un cambio del 10%
Regulación de la carga 0.05% para un cambio del 50%
Rizo 3.0 mV máximo Pico-a-Pico
Rango de Ajuste de CD de Salida +/- 5% Mínimo
Protección de Sobrevoltaje Todas las salidas de 5-Volt incluyen OVP integrada como un estándar (el ajuste es 6.2 V ±0.4 V) OVP está disponible opcionalmente en otros tipos
Presentir de telemandoRefiérase al esquema Terminal del Bloque para la producción (s) con presentir de telemando.
Protección contra Sobrecarga 125 to 150% foldback automático de limitación de corriente
• Terminales de conexión fáciles de instalar. • Tight regulation: 0.05% Line; 0.05% Load• Las calificaciones de salida a +50oC• OVP integrada en modelos de 5 V y opcional en los
modelos de 12 y 24 V. • Foldback Current Limiting Protección contra
Sobrecarga con Automático Recupera
• Multi-Tap AC Las Entradas• 100% Cuatro Hora Burn-in• Sírvase consultar “Términos y Condiciones, y
Políticas y Procedimientos de Ventas” • Reconocido por UL • Certificado CSA • Aprovado en CE • Certificado CB
Linear Open Frame DC Power SuppliesSilver Line Instruction Manual
Models: SLS-12-051T, SLS-15-045T, SLS-24-036T, SLS-05-090-1T
Features
Input AC Connections (See Case C)
General Specifications
Voltage/Current RatingsModel Numbers Output
SLS-12-051T 12 V / 5.1 A
SLS-15-045T 15 V / 4.5 A
SLS-24-036T 24 V / 3.6 A
SLS-05-090-1T 5 V / 9.0 A
Operating Temperature Range 0 to +50oC (Derate to 40% at +70oC)
Temperature Coefficient (Typical) +/- 0.01% / oC
Stability Within +/- 0.05% (24 hours after warm-up)
Vibration Per MIL-STD-810C, Method 514
Shock Per MIL-STD-810C, Method 516
EMI/RFI
Linear power supplies have inherently low conducted and radiated noise levels. For most system applications, these power supplies will meet the requirements of FCC Class “B” and VDE 0871 for Class “B” equipment without additional noise filtering.
Cooling Forced air. 20 CFM required for full rating Derate 30% for convection cooling.
Input SpecificationsMulti Input (all units) 100/120/220/230/240 VAC selectable +/- 10% except 230 VAC is +15%, -6%
Frequency Range 47-63 Hz (Typical is 60 Hz. Derate output 10% at 50 Hz)
Transient Response Time50 µsec at 50% load changes for outputs rated up to 6A
100 µsec at 50% load changes for outputs rated 6A and over.
Fuse Requirements Units are not fused internally. For safe operation, user must provide input line fuse as per values given in table.
Output Specifications
Line Regulation 0.05% for +/- 10% change
Load Regulation 0.05% for 50% change
Ripple 3.0 mV maximum peak-to-peak
DC Output Adjustment Range +/- 5% minimum
Overvoltage Protection All 5 volt outputs include built-in OVP as standard (setting is 6.2 V +/- 0.4 V). OVP is optionally available on other outputs.
Remote Sensing All units listed have remote sensing capability.
Overload Protection 125 to 150% foldback current limit Contact Technical Services at 1-800-377-4384 or [email protected] with any questions. Visit our website at www.solaheviduty.com
*Note: Unit is shipped for 120V input from factory.
**Primary Fuse for SLS-24-036T
For use at: Connect Apply AC to: Primary Fuse Primary Fuse**100 VAC 1-3, 2-4 1 & 5 1.6A / 125V 2A/125V
120 VAC* 1-3, 2-4 1 & 4 1.6A / 125V 2A/125V
220 VAC 2-3 1 & 5 0.8A / 250V 1A/250V
230 VAC 2-3 1 & 4 0.8A / 250V 1A/250V
240 VAC 2-3 1 & 4 0.8A / 250V 1A/250V
Mechanical Dimensions: Inches (mm)
Case C Note: The SLS models DC output can be adjusted with R13 V. ADJ.
R7 I. LIM is factory set and should not be adjusted by users.
7.00 " ( 178)
6.250" (158.8)
AC INPUT/DC OUTPUT
.50" (12.7)
. 50" (12.9)
75”
0.83 (21.08) 6.27 (159.26)
(19.1)
4.87
"(1
23.7
)2.
75"
(69.
9)
1.24
8"
( 31.
7)
. 38" (9.6 )
4.12
5"(1
04.8
)
OV P ( OPTIONAL )° MTG HOLES (1 2 P LACES)
1.248" (31.7) . 75" (19.1)
188"(4.8 )
MA X
. 551" (14)
+S41 235 -OU
T-S+O
UT
WEIGH T: 7.28 LBS.(3.3 KG)
PEM NU T HOLES8-32 MTG (4 PLACES)
Top View
Cas e C
R13V. ADJ
R7I.LIM
Application Note: User needs to provide earth ground to power supply with either solder to Tab or using washer and nut assembly. The SLS power supply is shipped from the factory with metal shorting straps connected between the + OUT and + S terminals and the (-) OUT and (-) S terminals. This strapping configuration allows the output of the SLS to be taken from either pair of terminals. This is the standard configuration. The remote sense feature is enabled by removing the shorting straps and connecting the individual OUT and S terminals to the appropriate points of the load. If an OVP circuit is used it should be connected to the + OUT and (-) OUT terminals. The OVP should never be connected to the + S, - S terminals without the use of the shorting straps. In all cases it is critical that the terminal screws be firmly tightened.
• Easy installation with strip terminal• Tight regulation: 0.05% Line; 0.05% Load• Full Output Ratings to +50oC• Built in OVP on 5 Volt Outputs• OVP Option for 12V, 15V and 24V• Foldback Current Limiting Overload Protection with
Automatic Recovery
• Multi-Tap AC Inputs• 100% Four-Hour Burn-in• Please see enclosed “Terms & Conditions and
Sales & Policies & Procedures”• UL Recognized• CSA Certified• CE Marked• CB Certified
Serie SL - Lineales de Salida Sencilla & Múltiple Manual de la Instrucción Modelos: SLS-12-051T, SLS-15-045T,
SLS-24-036T, SLS-05-090-1T
Características
Entrada AC Conexiones (See Caja C)
Especificaciones
Contacte los Servicios Técnicos en 1-847-268-6000 o [email protected] con cualquiera preguntan. Visite nuestro sitio web en www.solaheviduty. com
* La nota: La unidad se envia para la entrada 120V de la fábrica.
**El fusible primario for SLS-24-036T
Para el uso en: Conecte Aplique AC a: El fusible primario El fusible primario**100 VAC 1-3, 2-4 1 & 5 1.6A / 125V 2A/125V
120 VAC* 1-3, 2-4 1 & 4 1.6A / 125V 2A/125V
220 VAC 2-3 1 & 5 0.8A / 250V 1A/250V
230 VAC 2-3 1 & 4 0.8A / 250V 1A/250V
240 VAC 2-3 1 & 4 0.8A / 250V 1A/250V
P/N A272-024 Rev. 4 (August 16, 2007)
Caja C La nota: La salida DC de los modelos SLS puede ser ajustada con el R13 V. ADJ
R7 I. LIM ha sido fijada en la fabrica y no se debe ajustar por los usuarios.
7.00 " ( 178)
6.250" (158.8)
AC INPUT/DC OUTPUT
.50" (12.7)
. 50" (12.9)
75”
0.83 (21.08) 6.27 (159.26)
(19.1)
4.87
"(1
23.7
)2.
75"
(69.
9)
1.24
8"
( 31.
7)
. 38" (9.6 )
4.12
5"(1
04.8
)
OV P ( OPTIONAL )° MTG HOLES (1 2 P LACES)
1.248" (31.7) . 75" (19.1)
188"(4.8 )
MA X
. 551" (14)
+S41 235 -OU
T-S+O
UT
WEIGH T: 7.28 LBS.(3.3 KG)
PEM NU T HOLES8-32 MTG (4 PLACES)
Top View
Cas e C
R13V. ADJ
R7I.LIM
La Nota de la aplicación: Las necesidades de Usuario a proporcionar la tierra el suelo para accionar el suministro con o soldadura qa la Etiqueta o utilizar arandela y asamblea de nuez. La planta SLS se envía de fábrica con bandas metálicas de cortocircuito conectadas entre los terminales + OUT (salida) y + S y los terminales (-) OUT y (-) S. Esta configuración de bandas permite la salida desde la SLS desde cualquier par de terminales, y es la configuración estándar. La función de sensor remoto se activa al retirar las bandas de cortocircuito y conectar los terminales individuales de salida (OUT) y S con los puntos pertinentes de la carga. Si se utiliza un circuito OVP, deberá conectarse con los terminales + OUT y (-) OUT. El circuito OVP no debe conectarse nunca con los terminales + S, - S sin las bandas de cortocircuito. En todos los casos es esencial ajustar los tornillos del terminal firmemente.
Dimensiones (pulg/mm)Voltaje/Las Calificaciones Actuales
Número de Catálogo Salida 1
SLS-12-051T 12 V / 5.1 A
SLS-15-045T 15 V / 4.5 A
SLS-24-036T 24 V / 3.6 A
SLS-05-090-1T 5 V / 9.0 A
Rango de Operación de Temperatura 0 to +50oC (Ajuste al 40% a +70oC)
Coeficiente de Temperatura (Típico) +/- 0.01% / oC
Estabilidad Dentro de +/- 0.05% (24 horas después del calentamiento)
Vibración De acuerdo con MIL-STD-810C, Método 514
Golpes De acuerdo con MIL-STD-810C, Método 516
EMI/RFILas fuentes de alimentación lineales tienen inherentemente bajos niveles de ruido conducido y radiado. Para la mayoría de las aplicaciones en sistemas estas cumplen con los requerimientos de FCC Clase B y VDE 0871 para Clase B.
Enfriamiento De aire forzado. 20 CFM requeridos para el grado completo reducen la capacidad normal del 30% para refrescarse de la convección.
EntradaVoltaje de Entrada 100/120/220/230/240 VAC selectable +/- 10% except 230 VAC is +15%, -6%
Frecuencia de Entrada 47-63 Hz (Típico es 60 Hz. La producción de Derate 10% en 50 Hz)
Tiempo de Respuesta a Transientes 50 µsec en 50% la carga cambia para producciones valoradas hasta 6A. 100 µsec en 50% la carga cambia para producciones valoradas 6A y sobre.
Funda los RequisitosLas unidades no se funden internamente. Para la operación segura, el usuario debe proporcionar fusible de entrada de línea como por valores se rindió tabla.
SalidaRegulación de Línea 0.05% para un cambio del 10%
Regulación de la carga 0.05% para un cambio del 50%
Rizo 3.0 mV máximo Pico-a-Pico
Rango de Ajuste de CD de Salida +/- 5% Mínimo
Protección de Sobrevoltaje Todas las salidas de 5-Volt incluyen OVP integrada como un estándar (el ajuste es 6.2 V ±0.4 V) OVP está disponible opcionalmente en otros tipos
Presentir de telemando Refiérase al esquema Terminal del Bloque para la producción (s) con presentir de telemando.
Protección contra Sobrecarga 125 to 150% foldback automático de limitación de corriente
Sensores Remotos Todas unidades listaron tiene la capacidad de sensores remotos.
• Terminales de conexión fáciles de instalar. • Tight regulation: 0.05% Line; 0.05% Load• Las calificaciones de salida a +50oC• OVP integrada en modelos de 5 V y opcional en los
modelos de 12, 15 y 24 V. • Foldback Current Limiting Protección contra
Sobrecarga con Automático Recupera
• Multi-Tap AC Las Entradas• 100% Cuatro Hora Burn-in• Sírvase consultar “Términos y Condiciones, y
Políticas y Procedimientos de Ventas” • Reconocido por UL • Certificado CSA • Aprovado en CE • Certificado CB
Linear Open Frame DC Power SuppliesSilver Line Instruction Manual
Models: SLS-05-030-1T, SLS-12-017T, SLS-24-012T
Features
General Specifications
Voltage/Current Ratings
Model Number Output
SLS-05-030-1T 5V/3.0A
SLS-12-017T +12V/1.7A or +15V/1.5A
SLS-24-012T +24V/1.2A
Operating Temperature Range 0 to +50oC (Derate to 40% at +70oC)
Temperature Coefficient (Typical) +/- 0.01% / oC
Stability Within +/- 0.05% (24 hours after warm-up)
Vibration Per MIL-STD-810C, Method 514
Shock Per MIL-STD-810C, Method 516
EMI/RFI
Linear power supplies have inherently low conducted and radiated noise levels. For most system applications, these power supplies will meet the requirements of FCC Class “B” and VDE 0871 for Class “B” equipment without additional noise filtering.
Cooling Forced air. 20 CFM required for full rating Derate 30% for convection cooling.
Input Specifications
Multi Input (all units) 100/120/220/230/240 VAC selectable +/- 10% except 230 VAC is +15%, -6%
Frequency Range 47-63 Hz (Typical is 60 Hz. Derate output 10% at 50 Hz)
Transient Response Time50 µsec at 50% load changes for outputs rated up to 6A
100 µsec at 50% load changes for outputs rated 6A and over
Fuse Requirements Units are not fused internally. For safe operation, user must provide input line fuse as per values given in table.
Output Specifications
Line Regulation 0.05% for +/- 10% change
Load Regulation 0.05% for 50% change
Ripple 3.0 mV maximum peak-to-peak
DC Output Adjustment Range +/- 5% minimum
Overvoltage Protection All 5 volt outputs include built-in OVP as standard (setting is 6.2V +/- 0.4V). OVP is optionally available on other outputs
Remote Sensing All units listed have remote sensing capability.
Overload Protection 125 to 150% foldback current limit
Contact Technical Services at 1-800-377-4384 or [email protected] with any questions. Visit our website at www.solaheviduty.com
InstallationStep 1: Check the input AC connections
Step 2: Connect the AC input according to table below.
Note: SLS-12-017T can be set to a +12V to +15V range by adjusting R9 V. ADJ.
Contact Technical Services at 1-800-377-4384 or [email protected] with any questions. Visit our website at www.solaheviduty.com
Input AC Connections (See Case A)
Mechanical Dimensions: Inches (mm)
For use at: Connect Apply AC to: Primary Fuse Primary Fuse
SLS-05-030-1T SLS-12-017TSLS-24-012T
100 VAC 1-3, 2-4 1 & 5 0.5A / 125V 1.0A / 125V
120 VAC* 1-3, 2-4 1 & 4 0.5A / 125V 1.0A / 125V
220 VAC 2-3 1 & 5 0.25A / 250V 0.5A / 250V
230 VAC 2-3 1 & 4 0.25A / 250V 0.5A / 250V
240 VAC 2-3 1 & 4 0.25A / 250V 0.5A / 250V
Case A Note: The SLS models DC output can be adjusted with R9 V. ADJ.
R7 I. LIM is factory set and should not be adjusted by users.
.744" (18.9)
. 450" (11.5) MAX
0.188"(4.8 )
4.843" (123)
4.142" (105.2) 0.48" (12.2)
1.62" (41)
° MTG HOLES (6 PLACES)
AC INPUT/DC OUTPUT
OVP(OPTIONAL )
.744
"(1
8.9)
.58"
(14-
8)
.378
"(9
.6)3.
992"
( 101
.4)
3.37
0"(8
5.6)
4
+S 1 235-OU
T-S+O
UT
WEIGH T: 2.43 L BS.(1.1 KG )
PEM NUT HOLE S 6-32 MT G ( 4 P LACES)
R7I-LIM ADJ
R9V. ADJ
*Note: Unit is shipped for 120V input from factory.
Application Note: User needs to provide earth ground to power supply with either solder to Tab or using washer and nut assembly. The SLS power supply is shipped from the factory with metal shorting straps connected between the + OUT and + S terminals and the (-) OUT and (-) S terminals. This strapping configuration allows the output of the SLS to be taken from either pair of terminals. This is the standard configuration. The remote sense feature is enabled by removing the shorting straps and connecting the individual OUT and S terminals to the appropriate points of the load. If an OVP circuit is used it should be connected to the + OUT and (-) OUT terminals. The OVP should never be connected to the + S, - S terminals without the use of the shorting straps. In all cases it is critical that the terminal screws be firmly tightened.
• Easy installation with strip terminal• Adjustable output• Tight regulation: 0.05% Line; 0.05% Load• Full Output Ratings to +50oC• Built in OVP on 5 Volt Outputs• OVP Option for 12V, 15V and 24V• Foldback Current Limiting Overload Protection with
Automatic Recovery
• Multi-Tap AC Inputs• 100% Four-Hour Burn-in• Please see enclosed “Terms & Conditions and
Sales & Policies & Procedures”• UL Recognized• CSA Certified• CE Marked• CB Certified
Contacte los Servicios Técnicos en 1-847-268-6000 o [email protected] con cualquiera preguntan. Visite nuestro sitio web en www.solaheviduty. com
Contacte los Servicios Técnicos en 1-847-268-6000 o [email protected] con cualquiera preguntan. Visite nuestro sitio web en www.solaheviduty. com
Serie SL - Lineales de Salida Sencilla & Múltiple Manual de la Instrucción
Modelos: SLS-05-030-1T, SLS-12-017T, SLS-24-012T
Características
Especificaciones
InstalaciónDé un paso 1: Verifica las conexiones de entrada de C.A.
Dé un paso 2: Conecte a la entrada de C.A. según posponer abajo.
La nota: SLS-12-017T se puede establecer en el rango +12V to +15V ajustando R9 V. ADJ.
P/N A272-022 Rev. 4 (August 16, 2007)
Entrada AC Conexiones (See Caja A)
Caja A La nota: La salida DC de los modelos SLS puede ser ajustada con el R9 V. ADJ
R7 I. LIM ha sido fijada en la fabrica y no se debe ajustar por los usuarios.
.744" (18.9)
. 450" (11.5) MAX
0.188"(4.8 )
4.843" (123)
4.142" (105.2) 0.48" (12.2)
1.62" (41)
° MTG HOLES (6 PLACES)
AC INPUT/DC OUTPUT
OVP(OPTIONAL )
.744
"(1
8.9)
.58"
(14-
8)
.378
"(9
.6)3.
992"
( 101
.4)
3.37
0"(8
5.6)
4
+S 1 235-OU
T-S+O
UT
WEIGH T: 2.43 L BS.(1.1 KG )
PEM NUT HOLE S 6-32 MT G ( 4 P LACES)
R7I-LIM ADJ
R9V. ADJ
Para el uso en: Conecte Aplique AC a: El fusible primario El fusible primario
SLS-05-030-1T SLS-12-017TSLS-24-012T
100 VAC 1-3, 2-4 1 & 5 0.5A / 125V 1.0A / 125V
120 VAC* 1-3, 2-4 1 & 4 0.5A / 125V 1.0A / 125V
220 VAC 2-3 1 & 5 0.25A / 250V 0.5A / 250V
230 VAC 2-3 1 & 4 0.25A / 250V 0.5A / 250V
240 VAC 2-3 1 & 4 0.25A / 250V 0.5A / 250V
* La nota: La unidad se envía para la entrada 120V de la fábrica.
La Nota de la aplicación: Las necesidades de Usuario a proporcionar la tierra el suelo para accionar el suministro con o soldadura qa la Etiqueta o utilizar arandela y asamblea de nuez. La planta SLS se envía de fábrica con bandas metálicas de cortocircuito conectadas entre los terminales + OUT (salida) y + S y los terminales (-) OUT y (-) S. Esta configuración de bandas permite la salida desde la SLS desde cualquier par de terminales, y es la configuración estándar. La función de sensor remoto se activa al retirar las bandas de cortocircuito y conectar los terminales individuales de salida (OUT) y S con los puntos pertinentes de la carga. Si se utiliza un circuito OVP, deberá conectarse con los terminales + OUT y (-) OUT. El circuito OVP no debe conectarse nunca con los terminales + S, - S sin las bandas de cortocircuito. En todos los casos es esencial ajustar los tornillos del terminal firmemente.
Dimensiones (pulg/mm)
Voltaje/Las Calificaciones ActualesNúmero de Catálogo Salida
SLS-05-030-1T 5V/3.0A
SLS-12-017T +12V/1.7A or +15V/1.5A
SLS-24-012T +24V/1.2A
Rango de Operación de Temperatura 0 to +50oC (Ajuste al 40% a +70oC)
Coeficiente de Temperatura (Típico) +/- 0.01% / oC
Estabilidad Dentro de +/- 0.05% (24 horas después del calentamiento)
Vibración De acuerdo con MIL-STD-810C, Método 514
Golpes De acuerdo con MIL-STD-810C, Método 516
EMI/RFILas fuentes de alimentación lineales tienen inherentemente bajos niveles de ruido conducido y radiado. Para la mayoría de las aplicaciones en sistemas estas cumplen con los requerimientos de FCC Clase B y VDE 0871 para Clase B.
Enfriamiento De aire forzado. 20 CFM requeridos para el grado completo reducen la capacidad normal del 30% para refrescarse de la convección.
EntradaVoltaje de Entrada 100/120/220/230/240 VAC selectable +/- 10% except 230 VAC is +15%, -6%
Frecuencia de Entrada 47-63 Hz (Típico es 60 Hz. La producción de Derate 10% en 50 Hz)
Tiempo de Respuesta a Transientes50 µsec en 50% la carga cambia para producciones valoradas hasta 6A.
100 µsec en 50% la carga cambia para producciones valoradas 6A y sobre.
Funda los RequisitosLas unidades no se funden internamente. Para la operación segura, el usuario debe proporcionar fusible de entrada de línea como por valores se rindió tabla.
SalidaRegulación de Línea 0.05% para un cambio del 10%
Regulación de la carga 0.05% para un cambio del 50%
Rizo 3.0 mV máximo Pico-a-Pico
Rango de Ajuste de CD de Salida +/- 5% Mínimo
Protección de Sobrevoltaje Las salidas de 5 voltios incluyen OVP incorporado como estándar (el ajuste es 6.2V +/- 0.4V). OVP está opcionalmente disponible en otras salidas
Protección contra Sobrecarga 125 to 150% foldback automático de limitación de corriente
Sensores Remotos Todas unidades listaron tiene la capacidad de sensores remotos.
• Terminales de conexión fáciles de instalar. • De salida ajustable• Tight regulation: 0.05% Line; 0.05% Load• Las calificaciones de salida a +50oC• OVP integrada en modelos de 5 V y opcional en los
modelos de 12, 15 y 24 V. • Foldback Current Limiting Protección contra
Sobrecarga con Automático Recupera
• Multi-Tap AC Las Entradas• 100% Cuatro Hora Burn-in• Sírvase consultar “Términos y Condiciones, y
Políticas y Procedimientos de Ventas” adjunto.• Reconocido por UL • Certificado CSA • Aprovado en CE • Certificado CB
Linear Open Frame DC Power SuppliesSilver Line Instruction Manual
Models: SLS-05-060-1T, SLS-12-034T, SLS-24-024T
Features
Input AC Connections (See Case B)
For use at: Connect Apply AC to:
Primary Fuse(SLS-05-0601T)(SLS-12-034T)(SLS-24-024T)
100 VAC 1-3, 2-4 1 & 5 1.6A / 125V
120 VAC* 1-3, 2-4 1 & 4 1.6A / 125V
220 VAC 2-3 1 & 5 0.8A / 250V
230 VAC 2-3 1 & 4 0.8A / 250V
240 VAC 2-3 1 & 4 0.8A / 250VGeneral Specifications
Voltage/Current RatingsModel Number Output
SLS-05-060-1T +5V / 6.0 A
SLS-12-034-T +12V / 3.4 A
SLS-24-024-T +24V / 2.4 A
Operating Temperature Range 0 to +50oC (Derate to 40% at +70oC)
Temperature Coefficient (Typical) +/- 0.01% / oC
Stability Within +/- 0.05% (24 hours after warm-up)
Vibration Per MIL-STD-810C, Method 514
Shock Per MIL-STD-810C, Method 516
EMI/RFI
Linear power supplies have inherently low conducted and radiated noise levels. For most system applications, these power supplies will meet the requirements of FCC Class “B” and VDE 0871 for Class “B” equipment without additional noise filtering.
Cooling Forced air. 20 CFM required for full rating Derate 30% for convection cooling.
Input SpecificationsMulti Input (all units) 100/120/220/230/240 VAC selectable +/- 10% except 230 VAC is +15%, -6%
Frequency Range 47-63 Hz (Typical is 60 Hz. Derate output 10% at 50 Hz)
Transient Response Time 50 µsec at 50% load changes for outputs rated up to 6A
Fuse Requirements Units are not fused internally. For safe operation, user must provide input line fuse as per values given in table.
Output Specifications
Line Regulation 0.05% for +/- 10% change
Load Regulation 0.05% for 50% change
Ripple 3.0 mV maximum peak-to-peak
DC Output Adjustment Range +/- 5% minimum
Overvoltage Protection All 5 volt outputs include built-in OVP as standard (setting is 6.2 V +/- 0.4 V). OVP is optionally available on other outputs.
Remote Sensing All units listed have remote sensing capability.
Overload Protection 125 to 150% foldback current limit
Contact Technical Services at 1-800-377-4384 or [email protected] with any questions. Visit our website at www.solaheviduty.com
Contact Technical Services at 1-800-377-4384 or [email protected] with any questions. Visit our website at www.solaheviduty.com
Mechanical Dimensions: inches (mm)
Case BUse Case B1 Output Configuration for SLS-05-060-1T and SLS-12-034T.
Use Case B2 Output Configuration for SLS-24-024T.
Note: The SLS models DC output can be adjusted with R10 V. ADJ. R8 I. LIM is factory set and should not be adjusted by users.
0.72" (18.3)
4.87" (123.5)
4.118" (104.6)
0.188"(4.8)
2.5
0"
(62
.8)
1.2
8"
(32
.5)
° MTG HOLES (8 PLACES )
0.433" (11)
5.6
2"
(14
2.6
)
0.252” (6.4)
4.8
75
"(1
24
)
AC
INP
UT
/D
CO
UT
PU
TO
VP
(OP
TIO
NA
L)
0.72" (18.3)
1.28" (32.5)
MAX
.450" (11.5)
.39"(10)
4
1
23
5
-S
+OUT+S
-OUT
WEIGHT: 4 LBS.(1.8 )KG
PEM NUT HOLES6-32 MTG (4 PLACES)
4
1
23
5
+S
-OUT-S
+OUT
CASE B1
CASE B2
R10 V.ADJ
R8 I.LIM
Application Note: User needs to provide earth ground to power supply with either solder to Tab or using washer and nut assembly. The SLS power supply is shipped from the factory with metal shorting straps connected between the + OUT and + S terminals and the (-) OUT and (-) S terminals. This strapping configuration allows the output of the SLS to be taken from either pair of terminals. This is the standard configuration. The remote sense feature is enabled by removing the shorting straps and connecting the individual OUT and S terminals to the appropriate points of the load. If an OVP circuit is used it should be connected to the + OUT and (-) OUT terminals. The OVP should never be connected to the + S, - S terminals without the use of the shorting straps. In all cases it is critical that the terminal screws be firmly tightened.
*Note: Unit is shipped for 120V input from factory.
• Easy installation with strip terminal• Tight regulation: 0.05% Line; 0.05% Load• Full Output Ratings to +50oC• Built in OVP on 5 Volt Outputs• OVP Option for 12V and 24V• Foldback Current Limiting Overload Protection with
Automatic Recovery
• Multi-Tap AC Inputs• 100% Four-Hour Burn-in• Please see enclosed “Terms & Conditions and
Sales & Policies & Procedures”• UL Recognized• CSA Certified• CE Marked• CB Certified
Serie SL - Lineales de Salida Sencilla & Múltiple Manual de la Instrucción
Modelos: SLS-05-060-1T, SLS-12-034T, SLS-24-024T
Características
Entrada AC Conexiones (See Caja B)
Especificaciones
Para el uso en: Conecte Aplique AC a:
El fusible primario(SLS-05-0601T)(SLS-12-034T)(SLS-24-024T)
100 VAC 1-3, 2-4 1 & 5 1.6A / 125V
120 VAC* 1-3, 2-4 1 & 4 1.6A / 125V
220 VAC 2-3 1 & 5 0.8A / 250V
230 VAC 2-3 1 & 4 0.8A / 250V
240 VAC 2-3 1 & 4 0.8A / 250V
Contacte los Servicios Técnicos en 1-847-268-6000 o [email protected] con cualquiera preguntan. Visite nuestro sitio web en www.solaheviduty. com
Contacte los Servicios Técnicos en 1-847-268-6000 o [email protected] con cualquiera preguntan. Visite nuestro sitio web en www.solaheviduty. com
P/N A272-023 Rev. 3 (August 16, 2007)
* La nota: La unidad se envia para la entrada 120V de la fábrica.
Caja BUtilice la configuración de salida del caso B1 para SLS-05-060-1T y SLS-12-034T.
Utilice la configuración de salida del caso B2 para SLS-24-024T.
La nota: La salida DC de los modelos SLS puede ser ajustada con el R10 V. ADJ R8 I. LIM ha sido fijada en la fabrica y no se debe ajustar por los usuarios.
0.72" (18.3)
4.87" (123.5)
4.118" (104.6)
0.188"(4.8)
2.5
0"
(62
.8)
1.2
8"
(32
.5)
° MTG HOLES (8 PLACES )
0.433" (11)
5.6
2"
(14
2.6
)
0.252” (6.4)
4.8
75
"(1
24
)
AC
INP
UT
/D
CO
UT
PU
TO
VP
(OP
TIO
NA
L)
0.72" (18.3)
1.28" (32.5)
MAX
.450" (11.5)
.39"(10)
4
1
23
5
-S
+OUT+S
-OUT
WEIGHT: 4 LBS.(1.8 )KG
PEM NUT HOLES6-32 MTG (4 PLACES)
4
1
23
5
+S
-OUT-S
+OUT
CASE B1
CASE B2
R10 V.ADJ
R8 I.LIM
La Nota de la aplicación: Las necesidades de Usuario a proporcionar la tierra el suelo para accionar el suministro con o soldadura qa la Etiqueta o utilizar arandela y asamblea de nuez. La planta SLS se envía de fábrica con bandas metálicas de cortocircuito conectadas entre los terminales + OUT (salida) y + S y los terminales (-) OUT y (-) S. Esta configuración de bandas permite la salida desde la SLS desde cualquier par de terminales, y es la configuración estándar. La función de sensor remoto se activa al retirar las bandas de cortocircuito y conectar los terminales individuales de salida (OUT) y S con los puntos pertinentes de la carga. Si se utiliza un circuito OVP, deberá conectarse con los terminales + OUT y (-) OUT. El circuito OVP no debe conectarse nunca con los terminales + S, - S sin las bandas de cortocircuito. En todos los casos es esencial ajustar los tornillos del terminal firmemente.
Dimensiones (pulg/mm)Voltaje/Las Calificaciones ActualesNúmero de Catálogo Salida
SLS-05-060-1T +5V / 6.0 A
SLS-12-034-T +12V / 3.4 A
SLS-24-024-T +24V / 2.4 A
Rango de Operación de Temperatura 0 to +50oC (Ajuste al 40% a +70oC)
Coeficiente de Temperatura (Típico) +/- 0.01% / oC
Estabilidad Dentro de +/- 0.05% (24 horas después del calentamiento)
Vibración De acuerdo con MIL-STD-810C, Método 514
Golpes De acuerdo con MIL-STD-810C, Método 516
EMI/RFILas fuentes de alimentación lineales tienen inherentemente bajos niveles de ruido conducido y radiado. Para la mayoría de las aplicaciones en sistemas estas cumplen con los requerimientos de FCC Clase B y VDE 0871 para Clase B.
Enfriamiento De aire forzado. 20 CFM requeridos para el grado completo reducen la capacidad normal del 30% para refrescarse de la convección.
EntradaVoltaje de Entrada 100/120/220/230/240 VAC selectable +/- 10% except 230 VAC is +15%, -6%
Frecuencia de Entrada 47-63 Hz (Típico es 60 Hz. La producción de Derate 10% en 50 Hz)
Tiempo de Respuesta a Transientes 50 µsec en 50% la carga cambia para producciones valoradas hasta 6A.
Funda los RequisitosLas unidades no se funden internamente. Para la operación segura, el usuario debe proporcionar fusible de entrada de línea como por valores se rindió tabla.
SalidaRegulación de Línea 0.05% para un cambio del 10%
Regulación de la carga 0.05% para un cambio del 50%
Rizo 3.0 mV máximo Pico-a-Pico
Rango de Ajuste de CD de Salida +/- 5% Mínimo
Protección de Sobrevoltaje Todas las salidas de 5-Volt incluyen OVP integrada como un estándar (el ajuste es 6.2 V ±0.4 V) OVP está disponible opcionalmente en otros tipos
Presentir de telemandoRefiérase al esquema Terminal del Bloque para la producción (s) con presentir de telemando.
Protección contra Sobrecarga 125 to 150% foldback automático de limitación de corriente
• Terminales de conexión fáciles de instalar. • Tight regulation: 0.05% Line; 0.05% Load• Las calificaciones de salida a +50oC• OVP integrada en modelos de 5 V y opcional en los
modelos de 12 y 24 V. • Foldback Current Limiting Protección contra
Sobrecarga con Automático Recupera
• Multi-Tap AC Las Entradas• 100% Cuatro Hora Burn-in• Sírvase consultar “Términos y Condiciones, y
Políticas y Procedimientos de Ventas” • Reconocido por UL • Certificado CSA • Aprovado en CE • Certificado CB
Linear Open Frame DC Power SuppliesSilver Line Instruction Manual
Models: SLS-12-051T, SLS-15-045T, SLS-24-036T, SLS-05-090-1T
Features
Input AC Connections (See Case C)
General Specifications
Voltage/Current RatingsModel Numbers Output
SLS-12-051T 12 V / 5.1 A
SLS-15-045T 15 V / 4.5 A
SLS-24-036T 24 V / 3.6 A
SLS-05-090-1T 5 V / 9.0 A
Operating Temperature Range 0 to +50oC (Derate to 40% at +70oC)
Temperature Coefficient (Typical) +/- 0.01% / oC
Stability Within +/- 0.05% (24 hours after warm-up)
Vibration Per MIL-STD-810C, Method 514
Shock Per MIL-STD-810C, Method 516
EMI/RFI
Linear power supplies have inherently low conducted and radiated noise levels. For most system applications, these power supplies will meet the requirements of FCC Class “B” and VDE 0871 for Class “B” equipment without additional noise filtering.
Cooling Forced air. 20 CFM required for full rating Derate 30% for convection cooling.
Input SpecificationsMulti Input (all units) 100/120/220/230/240 VAC selectable +/- 10% except 230 VAC is +15%, -6%
Frequency Range 47-63 Hz (Typical is 60 Hz. Derate output 10% at 50 Hz)
Transient Response Time50 µsec at 50% load changes for outputs rated up to 6A
100 µsec at 50% load changes for outputs rated 6A and over.
Fuse Requirements Units are not fused internally. For safe operation, user must provide input line fuse as per values given in table.
Output Specifications
Line Regulation 0.05% for +/- 10% change
Load Regulation 0.05% for 50% change
Ripple 3.0 mV maximum peak-to-peak
DC Output Adjustment Range +/- 5% minimum
Overvoltage Protection All 5 volt outputs include built-in OVP as standard (setting is 6.2 V +/- 0.4 V). OVP is optionally available on other outputs.
Remote Sensing All units listed have remote sensing capability.
Overload Protection 125 to 150% foldback current limit Contact Technical Services at 1-800-377-4384 or [email protected] with any questions. Visit our website at www.solaheviduty.com
*Note: Unit is shipped for 120V input from factory.
**Primary Fuse for SLS-24-036T
For use at: Connect Apply AC to: Primary Fuse Primary Fuse**100 VAC 1-3, 2-4 1 & 5 1.6A / 125V 2A/125V
120 VAC* 1-3, 2-4 1 & 4 1.6A / 125V 2A/125V
220 VAC 2-3 1 & 5 0.8A / 250V 1A/250V
230 VAC 2-3 1 & 4 0.8A / 250V 1A/250V
240 VAC 2-3 1 & 4 0.8A / 250V 1A/250V
Mechanical Dimensions: Inches (mm)
Case C Note: The SLS models DC output can be adjusted with R13 V. ADJ.
R7 I. LIM is factory set and should not be adjusted by users.
7.00 " ( 178)
6.250" (158.8)
AC INPUT/DC OUTPUT
.50" (12.7)
. 50" (12.9)
75”
0.83 (21.08) 6.27 (159.26)
(19.1)
4.87
"(1
23.7
)2.
75"
(69.
9)
1.24
8"
( 31.
7)
. 38" (9.6 )
4.12
5"(1
04.8
)
OV P ( OPTIONAL )° MTG HOLES (1 2 P LACES)
1.248" (31.7) . 75" (19.1)
188"(4.8 )
MA X
. 551" (14)
+S41 235 -OU
T-S+O
UT
WEIGH T: 7.28 LBS.(3.3 KG)
PEM NU T HOLES8-32 MTG (4 PLACES)
Top View
Cas e C
R13V. ADJ
R7I.LIM
Application Note: User needs to provide earth ground to power supply with either solder to Tab or using washer and nut assembly. The SLS power supply is shipped from the factory with metal shorting straps connected between the + OUT and + S terminals and the (-) OUT and (-) S terminals. This strapping configuration allows the output of the SLS to be taken from either pair of terminals. This is the standard configuration. The remote sense feature is enabled by removing the shorting straps and connecting the individual OUT and S terminals to the appropriate points of the load. If an OVP circuit is used it should be connected to the + OUT and (-) OUT terminals. The OVP should never be connected to the + S, - S terminals without the use of the shorting straps. In all cases it is critical that the terminal screws be firmly tightened.
• Easy installation with strip terminal• Tight regulation: 0.05% Line; 0.05% Load• Full Output Ratings to +50oC• Built in OVP on 5 Volt Outputs• OVP Option for 12V, 15V and 24V• Foldback Current Limiting Overload Protection with
Automatic Recovery
• Multi-Tap AC Inputs• 100% Four-Hour Burn-in• Please see enclosed “Terms & Conditions and
Sales & Policies & Procedures”• UL Recognized• CSA Certified• CE Marked• CB Certified
Serie SL - Lineales de Salida Sencilla & Múltiple Manual de la Instrucción Modelos: SLS-12-051T, SLS-15-045T,
SLS-24-036T, SLS-05-090-1T
Características
Entrada AC Conexiones (See Caja C)
Especificaciones
Contacte los Servicios Técnicos en 1-847-268-6000 o [email protected] con cualquiera preguntan. Visite nuestro sitio web en www.solaheviduty. com
* La nota: La unidad se envia para la entrada 120V de la fábrica.
**El fusible primario for SLS-24-036T
Para el uso en: Conecte Aplique AC a: El fusible primario El fusible primario**100 VAC 1-3, 2-4 1 & 5 1.6A / 125V 2A/125V
120 VAC* 1-3, 2-4 1 & 4 1.6A / 125V 2A/125V
220 VAC 2-3 1 & 5 0.8A / 250V 1A/250V
230 VAC 2-3 1 & 4 0.8A / 250V 1A/250V
240 VAC 2-3 1 & 4 0.8A / 250V 1A/250V
P/N A272-024 Rev. 4 (August 16, 2007)
Caja C La nota: La salida DC de los modelos SLS puede ser ajustada con el R13 V. ADJ
R7 I. LIM ha sido fijada en la fabrica y no se debe ajustar por los usuarios.
7.00 " ( 178)
6.250" (158.8)
AC INPUT/DC OUTPUT
.50" (12.7)
. 50" (12.9)
75”
0.83 (21.08) 6.27 (159.26)
(19.1)
4.87
"(1
23.7
)2.
75"
(69.
9)
1.24
8"
( 31.
7)
. 38" (9.6 )
4.12
5"(1
04.8
)
OV P ( OPTIONAL )° MTG HOLES (1 2 P LACES)
1.248" (31.7) . 75" (19.1)
188"(4.8 )
MA X
. 551" (14)
+S41 235 -OU
T-S+O
UT
WEIGH T: 7.28 LBS.(3.3 KG)
PEM NU T HOLES8-32 MTG (4 PLACES)
Top View
Cas e C
R13V. ADJ
R7I.LIM
La Nota de la aplicación: Las necesidades de Usuario a proporcionar la tierra el suelo para accionar el suministro con o soldadura qa la Etiqueta o utilizar arandela y asamblea de nuez. La planta SLS se envía de fábrica con bandas metálicas de cortocircuito conectadas entre los terminales + OUT (salida) y + S y los terminales (-) OUT y (-) S. Esta configuración de bandas permite la salida desde la SLS desde cualquier par de terminales, y es la configuración estándar. La función de sensor remoto se activa al retirar las bandas de cortocircuito y conectar los terminales individuales de salida (OUT) y S con los puntos pertinentes de la carga. Si se utiliza un circuito OVP, deberá conectarse con los terminales + OUT y (-) OUT. El circuito OVP no debe conectarse nunca con los terminales + S, - S sin las bandas de cortocircuito. En todos los casos es esencial ajustar los tornillos del terminal firmemente.
Dimensiones (pulg/mm)Voltaje/Las Calificaciones Actuales
Número de Catálogo Salida 1
SLS-12-051T 12 V / 5.1 A
SLS-15-045T 15 V / 4.5 A
SLS-24-036T 24 V / 3.6 A
SLS-05-090-1T 5 V / 9.0 A
Rango de Operación de Temperatura 0 to +50oC (Ajuste al 40% a +70oC)
Coeficiente de Temperatura (Típico) +/- 0.01% / oC
Estabilidad Dentro de +/- 0.05% (24 horas después del calentamiento)
Vibración De acuerdo con MIL-STD-810C, Método 514
Golpes De acuerdo con MIL-STD-810C, Método 516
EMI/RFILas fuentes de alimentación lineales tienen inherentemente bajos niveles de ruido conducido y radiado. Para la mayoría de las aplicaciones en sistemas estas cumplen con los requerimientos de FCC Clase B y VDE 0871 para Clase B.
Enfriamiento De aire forzado. 20 CFM requeridos para el grado completo reducen la capacidad normal del 30% para refrescarse de la convección.
EntradaVoltaje de Entrada 100/120/220/230/240 VAC selectable +/- 10% except 230 VAC is +15%, -6%
Frecuencia de Entrada 47-63 Hz (Típico es 60 Hz. La producción de Derate 10% en 50 Hz)
Tiempo de Respuesta a Transientes 50 µsec en 50% la carga cambia para producciones valoradas hasta 6A. 100 µsec en 50% la carga cambia para producciones valoradas 6A y sobre.
Funda los RequisitosLas unidades no se funden internamente. Para la operación segura, el usuario debe proporcionar fusible de entrada de línea como por valores se rindió tabla.
SalidaRegulación de Línea 0.05% para un cambio del 10%
Regulación de la carga 0.05% para un cambio del 50%
Rizo 3.0 mV máximo Pico-a-Pico
Rango de Ajuste de CD de Salida +/- 5% Mínimo
Protección de Sobrevoltaje Todas las salidas de 5-Volt incluyen OVP integrada como un estándar (el ajuste es 6.2 V ±0.4 V) OVP está disponible opcionalmente en otros tipos
Presentir de telemando Refiérase al esquema Terminal del Bloque para la producción (s) con presentir de telemando.
Protección contra Sobrecarga 125 to 150% foldback automático de limitación de corriente
Sensores Remotos Todas unidades listaron tiene la capacidad de sensores remotos.
• Terminales de conexión fáciles de instalar. • Tight regulation: 0.05% Line; 0.05% Load• Las calificaciones de salida a +50oC• OVP integrada en modelos de 5 V y opcional en los
modelos de 12, 15 y 24 V. • Foldback Current Limiting Protección contra
Sobrecarga con Automático Recupera
• Multi-Tap AC Las Entradas• 100% Cuatro Hora Burn-in• Sírvase consultar “Términos y Condiciones, y
Políticas y Procedimientos de Ventas” • Reconocido por UL • Certificado CSA • Aprovado en CE • Certificado CB
Linear Open Frame DC Power SuppliesSilver Line Instruction Manual
Models: SLS-05-120-1T, SLS-12-068T, SLS-15-060T, SLS-24-048T
Features
Input AC Connections (See Case I2)
For use at: Connect Apply AC to:
Primary FuseSLS-05-120-1T
Primary FuseSLS-15-060TSLS-12-068T
Primary FuseSLS-24-048T
100 VAC 1-3, 2-4 1 & 5 2 A / 125 V 2.5 A / 125V 3.0A / 125V
120 VAC* 1-3, 2-4 1 & 4 2 A / 125 V 2.5 A / 125V 3.0A / 125V
220 VAC 2-3 1 & 5 1 A / 250 V 1.25A / 250V 1.5A / 250V
230 VAC 2-3 1 & 4 1 A / 250 V 1.25A / 250V 1.5A / 250V
240 VAC 2-3 1 & 4 1 A / 250 V 1.25A / 250V 1.5A / 250V
General Specifications
Voltage/Current RatingsModel Numbers Output (Volts) Output (Amps)
SLS-05-120-1T 5 12.0
SLS-12-068T 12 6.8
SLS-15-060T 15 6.0
SLS-24-048T 24 4.8
Operating Temperature Range 0 to +50oC (Derate to 40% at +70oC)
Temperature Coefficient (Typical) +/- 0.01% / oC
Stability Within +/- 0.05% (24 hours after warm-up)
Vibration Per MIL-STD-810C, Method 514
Shock Per MIL-STD-810C, Method 516
EMI/RFI
Linear power supplies have inherently low conducted and radiated noise levels. For most system applications, these power supplies will meet the requirements of FCC Class “B” and VDE 0871 for Class “B” equipment without additional noise filtering.
Cooling Forced air. 20 CFM required for full rating Derate 30% for convection cooling.
Input SpecificationsMulti Input (all units) 100/120/220/230/240 VAC selectable +/- 10% except 230 VAC is +15%, -6%
Frequency Range 47-63 Hz (Typical is 60 Hz. Derate output 10% at 50 Hz)
Transient Response Time50 µsec at 50% load changes for outputs rated up to 6A
100 µsec at 50% load changes for outputs rated 6A and over.
Fuse Requirements Units are not fused internally. For safe operation, user must provide input line fuse as per values given in table.
Output Specifications
Line Regulation 0.05% for +/- 10% change
Load Regulation 0.05% for 50% change
Ripple 3.0 mV maximum peak-to-peak
DC Output Adjustment Range +/- 5% minimum
Overvoltage Protection All 5 volt outputs include built-in OVP standard (setting is 6.2V +/- 0.4 V). OVP is optionally available on other outputs
Remote Sensing All units have remote sensing capability.
Overload Protection 125 to 150% foldback current limit Contact Technical Services at 1-800-377-4384 or [email protected] with any questions. Visit our website at www.solaheviduty.com
*Note: Unit is shipped for 120V input from factory.
Mechanical Dimensions: Inches (mm)
OVP (OPTIONAL)
8.00" (203). 512" (13)
9.00" (229)AC INPUT/DC OUTPUT
°MTG HOLES (12 PLACES). 473" (12)
. 188"(4.8 )
. 75" (19)
4.87
"(124
)2.75
"( 70)
1.25
0"(32)
4.12
5"(105
)
1.250" (32)
.39"
(10)
. 75" (19)
MAX
.551" (14)
Case I1
Case I2
Case I3
Case I4
WEIGHT: 7. 5 LBS.(3.4 KG)
+O
UT
41 235
+O
UT
-O
UT
-S
+S-S-O
UT
+S
AC Input 12V5V
+12V C
OM
+5V
+5V
-12V-12V-12V
+5V
+12V
+12V
-S +O
UT
+S+S
-S -OU
T
-S+S+O
UT
PEM NU T H OLES8-32 MT G ( 4 P LACES)
+S
+O
UT
-S-O
UT
AC Input
41 235
+O
UT
+O
UT
-O
UT
-S
+S-S-O
UT
+S
AC Input 12/15V
41 235
12/15V
AC Input41 235
R13I.LIM
R14V.ADJ
OVP (OPTIONAL)
8.00" (203). 512" (13)
9.00" (229)AC INPUT/DC OUTPUT
°MTG HOLES (12 PLACES)
. 473" (12). 188"(4.8 )
. 75" (19)
4.8
7"
(12
4)
2.7
5"
( 70
)
1.2
50
"(3
2)
4.1
25
"( 1
05
)
1.250" (32)
.39
"(1
0)
. 75" (19)
MAX
. 551" (14)
Case I1
Case I2
Case I3
Case I4
WEIGHT: 7. 5 LBS.(3.4 KG)
+O
UT
41 235
+O
UT
-O
UT
-S
+S-S-O
UT
+S
AC Input 12V5V
+1
2V CO
M
+5
V+
5V
-12
V-1
2V
-12
V
+5
V
+1
2V
+1
2V
-S +O
UT
+S
+S
-S -OU
T
-S+S
+O
UT
PEM NUT HOLES8-32 MTG (4 PLACES)
+S
+O
UT
-S-O
UT
AC Input
41 235
+O
UT
+O
UT
-O
UT
-S
+S
-S-O
UT
+S
AC Input 12/15V
41 235
12/15V
AC Input41 235
Please See
Voltage &
CurrentADJ
PlacementDiagrams
Case I2 Note: The SLS models DC output can be adjusted with R14 V. ADJ.
R13 I. LIM is factory set and should not be adjusted by users.
Application Note: User needs to provide earth ground to power supply with either solder to Tab or using washer and nut assembly. The SLS power supply is shipped from the factory with metal shorting straps connected between the + OUT and + S terminals and the (-) OUT and (-) S terminals. This strapping configuration allows the output of the SLS to be taken from either pair of terminals. This is the standard configuration. The remote sense feature is enabled by removing the shorting straps and connecting the individual OUT and S terminals to the appropriate points of the load. If an OVP circuit is used it should be connected to the + OUT and (-) OUT terminals. The OVP should never be connected to the + S, - S terminals without the use of the shorting straps. In all cases it is critical that the terminal screws be firmly tightened.
• Easy installation with strip terminal• Tight regulation: 0.05% Line; 0.05% Load• Full Output Ratings to +50oC• Built in OVP on 5 Volt Outputs• OVP Option for 12V, 15V and 24V• Foldback Current Limiting Overload Protection with
Automatic Recovery
• Multi-Tap AC Inputs• 100% Four-Hour Burn-in• Please see enclosed “Terms & Conditions and
Sales & Policies & Procedures”• UL Recognized• CSA Certified• CE Marked• CB Certified
Serie SL - Lineales de Salida Sencilla & Múltiple Manual de la Instrucción
Modelos: SLS-05-120-1T, SLS-12-068T, SLS-15-060T, SLS-24-048T
Características
Entrada AC Conexiones (See Caja I2)
Especificaciones
P/N A272-025 Rev. 4 (August 16, 2007)
Contacte los Servicios Técnicos en 1-847-268-6000 o [email protected] con cualquiera preguntan. Visite nuestro sitio web en www.solaheviduty. com
Para el uso en:: Conecte Aplique
AC a:
El fusible primario
SLS-05-120-1T
El fusible primario
SLS-15-060TSLS-12-068T
El fusible primario
SLS-24-048T
100 VAC 1-3, 2-4 1 & 5 2 A / 125 V 2.5 A / 125V 3.0A / 125V
120 VAC* 1-3, 2-4 1 & 4 2 A / 125 V 2.5 A / 125V 3.0A / 125V
220 VAC 2-3 1 & 5 1 A / 250 V 1.25A / 250V 1.5A / 250V
230 VAC 2-3 1 & 4 1 A / 250 V 1.25A / 250V 1.5A / 250V
240 VAC 2-3 1 & 4 1 A / 250 V 1.25A / 250V 1.5A / 250V
* La nota: La unidad se envia para la entrada 120V de la fábrica.
OVP (OPTIONAL)
8.00" (203). 512" (13)
9.00" (229)AC INPUT/DC OUTPUT
°MTG HOLES (12 PLACES). 473" (12)
. 188"(4.8 )
. 75" (19)
4.87
"(124
)2.75
"( 70)
1.25
0"(32)
4.12
5"(105
)
1.250" (32)
.39"
(10)
. 75" (19)
MAX
.551" (14)
Case I1
Case I2
Case I3
Case I4
WEIGHT: 7. 5 LBS.(3.4 KG)
+O
UT
41 235
+O
UT
-O
UT
-S
+S-S-O
UT
+S
AC Input 12V5V
+12V C
OM
+5V
+5V
-12V-12V-12V
+5V
+12V
+12V
-S +O
UT
+S+S
-S -OU
T
-S+S+O
UT
PEM NU T H OLES8-32 MT G ( 4 P LACES)
+S
+O
UT
-S-O
UT
AC Input
41 235
+O
UT
+O
UT
-O
UT
-S
+S-S-O
UT
+S
AC Input 12/15V
41 235
12/15V
AC Input41 235
R13I.LIM
R14V.ADJ
La Nota de la aplicación: Las necesidades de Usuario a proporcionar la tierra el suelo para accionar el suministro con o soldadura qa la Etiqueta o utilizar arandela y asamblea de nuez. La planta SLS se envía de fábrica con bandas metálicas de cortocircuito conectadas entre los terminales + OUT (salida) y + S y los terminales (-) OUT y (-) S. Esta configuración de bandas permite la salida desde la SLS desde cualquier par de terminales, y es la configuración estándar. La función de sensor remoto se activa al retirar las bandas de cortocircuito y conectar los terminales individuales de salida (OUT) y S con los puntos pertinentes de la carga. Si se utiliza un circuito OVP, deberá conectarse con los terminales + OUT y (-) OUT. El circuito OVP no debe conectarse nunca con los terminales + S, - S sin las bandas de cortocircuito. En todos los casos es esencial ajustar los tornillos del terminal firmemente.
Dimensiones (pulg/mm)Voltaje/Las Calificaciones ActualesNúmero de Catálogo Salida (Voltaje) Salida (Amps)
SLS-05-120-1T 5 12.0
SLS-12-068T 12 6.8
SLS-15-060T 15 6.0
SLS-24-048T 24 4.8
Rango de Operación de Temperatura 0 to +50oC (Ajuste al 40% a +70oC)
Coeficiente de Temperatura (Típico) +/- 0.01% / oC
Estabilidad Dentro de +/- 0.05% (24 horas después del calentamiento)
Vibración De acuerdo con MIL-STD-810C, Método 514
Golpes De acuerdo con MIL-STD-810C, Método 516
EMI/RFILas fuentes de alimentación lineales tienen inherentemente bajos niveles de ruido conducido y radiado. Para la mayoría de las aplicaciones en sistemas estas cumplen con los requerimientos de FCC Clase B y VDE 0871 para Clase B.
Enfriamiento De aire forzado. 20 CFM requeridos para el grado completo reducen la capacidad normal del 30% para refrescarse de la convección.
EntradaVoltaje de Entrada 100/120/220/230/240 VAC selectable +/- 10% except 230 VAC is +15%, -6%
Frecuencia de Entrada 47-63 Hz (Típico es 60 Hz. La producción de Derate 10% en 50 Hz)
Tiempo de Respuesta a Transientes 50 µsec en 50% la carga cambia para producciones valoradas hasta 6A. 100 µsec en 50% la carga cambia para producciones valoradas 6A y sobre.
Funda los RequisitosLas unidades no se funden internamente. Para la operación segura, el usuario debe proporcionar fusible de entrada de línea como por valores se rindió tabla.
SalidaRegulación de Línea 0.05% para un cambio del 10%
Regulación de la carga 0.05% para un cambio del 50%
Rizo 3.0 mV máximo Pico-a-Pico
Rango de Ajuste de CD de Salida +/- 5% Mínimo
Protección de Sobrevoltaje Todas las salidas de 5-Volt incluyen OVP integrada como un estándar (el ajuste es 6.2 V ±0.4 V) OVP está disponible opcionalmente en otros tipos
Protección contra Sobrecarga 125 to 150% foldback automático de limitación de corriente
Sensores Remotos Todas unidades listaron tiene la capacidad de sensores remotos.
OVP (OPTIONAL)
8.00" (203). 512" (13)
9.00" (229)AC INPUT/DC OUTPUT
°MTG HOLES (12 PLACES)
. 473" (12). 188"(4.8 )
. 75" (19)
4.8
7"
(12
4)
2.7
5"
( 70
)
1.2
50
"(3
2)
4.1
25
"( 1
05
)
1.250" (32)
.39
"(1
0)
. 75" (19)
MAX
. 551" (14)
Case I1
Case I2
Case I3
Case I4
WEIGHT: 7. 5 LBS.(3.4 KG)
+O
UT
41 235
+O
UT
-O
UT
-S
+S-S-O
UT
+S
AC Input 12V5V
+1
2V CO
M
+5
V+
5V
-12
V-1
2V
-12
V
+5
V
+1
2V
+1
2V
-S +O
UT
+S
+S
-S -OU
T
-S+S
+O
UT
PEM NUT HOLES8-32 MTG (4 PLACES)
+S
+O
UT
-S-O
UT
AC Input
41 235
+O
UT
+O
UT
-O
UT
-S
+S
-S-O
UT
+S
AC Input 12/15V
41 235
12/15V
AC Input41 235
Please See
Voltage &
CurrentADJ
PlacementDiagrams
Caja I2 La nota: La salida DC de los modelos SLS puede ser ajustada con el R14 V. ADJ
R13 I. LIM ha sido fijada en la fabrica y no se debe ajustar por los usuarios.
• Terminales de conexión fáciles de instalar. • De salida ajustable de 12V a 15V• Tight regulation: 0.05% Line; 0.05% Load• Las calificaciones de salida a +50oC• OVP integrada en modelos de 5 V y opcional en los
modelos de 12, 15 y 24 V. • Foldback Current Limiting Protección contra
Sobrecarga con Automático Recupera
• Multi-Tap AC Las Entradas• 100% Cuatro Hora Burn-in• Sírvase consultar “Términos y Condiciones, y
Políticas y Procedimientos de Ventas” • Reconocido por UL • Certificado CSA • Aprovado en CE • Certificado CB
Linear Open Frame DC Power SuppliesSilver Line Instruction Manual
Models: SLS-12-051T, SLS-15-045T, SLS-24-036T, SLS-05-090-1T
Features
Input AC Connections (See Case C)
General Specifications
Voltage/Current RatingsModel Numbers Output
SLS-12-051T 12 V / 5.1 A
SLS-15-045T 15 V / 4.5 A
SLS-24-036T 24 V / 3.6 A
SLS-05-090-1T 5 V / 9.0 A
Operating Temperature Range 0 to +50oC (Derate to 40% at +70oC)
Temperature Coefficient (Typical) +/- 0.01% / oC
Stability Within +/- 0.05% (24 hours after warm-up)
Vibration Per MIL-STD-810C, Method 514
Shock Per MIL-STD-810C, Method 516
EMI/RFI
Linear power supplies have inherently low conducted and radiated noise levels. For most system applications, these power supplies will meet the requirements of FCC Class “B” and VDE 0871 for Class “B” equipment without additional noise filtering.
Cooling Forced air. 20 CFM required for full rating Derate 30% for convection cooling.
Input SpecificationsMulti Input (all units) 100/120/220/230/240 VAC selectable +/- 10% except 230 VAC is +15%, -6%
Frequency Range 47-63 Hz (Typical is 60 Hz. Derate output 10% at 50 Hz)
Transient Response Time50 µsec at 50% load changes for outputs rated up to 6A
100 µsec at 50% load changes for outputs rated 6A and over.
Fuse Requirements Units are not fused internally. For safe operation, user must provide input line fuse as per values given in table.
Output Specifications
Line Regulation 0.05% for +/- 10% change
Load Regulation 0.05% for 50% change
Ripple 3.0 mV maximum peak-to-peak
DC Output Adjustment Range +/- 5% minimum
Overvoltage Protection All 5 volt outputs include built-in OVP as standard (setting is 6.2 V +/- 0.4 V). OVP is optionally available on other outputs.
Remote Sensing All units listed have remote sensing capability.
Overload Protection 125 to 150% foldback current limit Contact Technical Services at 1-800-377-4384 or [email protected] with any questions. Visit our website at www.solaheviduty.com
*Note: Unit is shipped for 120V input from factory.
**Primary Fuse for SLS-24-036T
For use at: Connect Apply AC to: Primary Fuse Primary Fuse**100 VAC 1-3, 2-4 1 & 5 1.6A / 125V 2A/125V
120 VAC* 1-3, 2-4 1 & 4 1.6A / 125V 2A/125V
220 VAC 2-3 1 & 5 0.8A / 250V 1A/250V
230 VAC 2-3 1 & 4 0.8A / 250V 1A/250V
240 VAC 2-3 1 & 4 0.8A / 250V 1A/250V
Mechanical Dimensions: Inches (mm)
Case C Note: The SLS models DC output can be adjusted with R13 V. ADJ.
R7 I. LIM is factory set and should not be adjusted by users.
7.00 " ( 178)
6.250" (158.8)
AC INPUT/DC OUTPUT
.50" (12.7)
. 50" (12.9)
75”
0.83 (21.08) 6.27 (159.26)
(19.1)
4.87
"(1
23.7
)2.
75"
(69.
9)
1.24
8"
( 31.
7)
. 38" (9.6 )
4.12
5"(1
04.8
)
OV P ( OPTIONAL )° MTG HOLES (1 2 P LACES)
1.248" (31.7) . 75" (19.1)
188"(4.8 )
MA X
. 551" (14)
+S41 235 -OU
T-S+O
UT
WEIGH T: 7.28 LBS.(3.3 KG)
PEM NU T HOLES8-32 MTG (4 PLACES)
Top View
Cas e C
R13V. ADJ
R7I.LIM
Application Note: User needs to provide earth ground to power supply with either solder to Tab or using washer and nut assembly. The SLS power supply is shipped from the factory with metal shorting straps connected between the + OUT and + S terminals and the (-) OUT and (-) S terminals. This strapping configuration allows the output of the SLS to be taken from either pair of terminals. This is the standard configuration. The remote sense feature is enabled by removing the shorting straps and connecting the individual OUT and S terminals to the appropriate points of the load. If an OVP circuit is used it should be connected to the + OUT and (-) OUT terminals. The OVP should never be connected to the + S, - S terminals without the use of the shorting straps. In all cases it is critical that the terminal screws be firmly tightened.
• Easy installation with strip terminal• Tight regulation: 0.05% Line; 0.05% Load• Full Output Ratings to +50oC• Built in OVP on 5 Volt Outputs• OVP Option for 12V, 15V and 24V• Foldback Current Limiting Overload Protection with
Automatic Recovery
• Multi-Tap AC Inputs• 100% Four-Hour Burn-in• Please see enclosed “Terms & Conditions and
Sales & Policies & Procedures”• UL Recognized• CSA Certified• CE Marked• CB Certified
Serie SL - Lineales de Salida Sencilla & Múltiple Manual de la Instrucción Modelos: SLS-12-051T, SLS-15-045T,
SLS-24-036T, SLS-05-090-1T
Características
Entrada AC Conexiones (See Caja C)
Especificaciones
Contacte los Servicios Técnicos en 1-847-268-6000 o [email protected] con cualquiera preguntan. Visite nuestro sitio web en www.solaheviduty. com
* La nota: La unidad se envia para la entrada 120V de la fábrica.
**El fusible primario for SLS-24-036T
Para el uso en: Conecte Aplique AC a: El fusible primario El fusible primario**100 VAC 1-3, 2-4 1 & 5 1.6A / 125V 2A/125V
120 VAC* 1-3, 2-4 1 & 4 1.6A / 125V 2A/125V
220 VAC 2-3 1 & 5 0.8A / 250V 1A/250V
230 VAC 2-3 1 & 4 0.8A / 250V 1A/250V
240 VAC 2-3 1 & 4 0.8A / 250V 1A/250V
P/N A272-024 Rev. 4 (August 16, 2007)
Caja C La nota: La salida DC de los modelos SLS puede ser ajustada con el R13 V. ADJ
R7 I. LIM ha sido fijada en la fabrica y no se debe ajustar por los usuarios.
7.00 " ( 178)
6.250" (158.8)
AC INPUT/DC OUTPUT
.50" (12.7)
. 50" (12.9)
75”
0.83 (21.08) 6.27 (159.26)
(19.1)
4.87
"(1
23.7
)2.
75"
(69.
9)
1.24
8"
( 31.
7)
. 38" (9.6 )
4.12
5"(1
04.8
)
OV P ( OPTIONAL )° MTG HOLES (1 2 P LACES)
1.248" (31.7) . 75" (19.1)
188"(4.8 )
MA X
. 551" (14)
+S41 235 -OU
T-S+O
UT
WEIGH T: 7.28 LBS.(3.3 KG)
PEM NU T HOLES8-32 MTG (4 PLACES)
Top View
Cas e C
R13V. ADJ
R7I.LIM
La Nota de la aplicación: Las necesidades de Usuario a proporcionar la tierra el suelo para accionar el suministro con o soldadura qa la Etiqueta o utilizar arandela y asamblea de nuez. La planta SLS se envía de fábrica con bandas metálicas de cortocircuito conectadas entre los terminales + OUT (salida) y + S y los terminales (-) OUT y (-) S. Esta configuración de bandas permite la salida desde la SLS desde cualquier par de terminales, y es la configuración estándar. La función de sensor remoto se activa al retirar las bandas de cortocircuito y conectar los terminales individuales de salida (OUT) y S con los puntos pertinentes de la carga. Si se utiliza un circuito OVP, deberá conectarse con los terminales + OUT y (-) OUT. El circuito OVP no debe conectarse nunca con los terminales + S, - S sin las bandas de cortocircuito. En todos los casos es esencial ajustar los tornillos del terminal firmemente.
Dimensiones (pulg/mm)Voltaje/Las Calificaciones Actuales
Número de Catálogo Salida 1
SLS-12-051T 12 V / 5.1 A
SLS-15-045T 15 V / 4.5 A
SLS-24-036T 24 V / 3.6 A
SLS-05-090-1T 5 V / 9.0 A
Rango de Operación de Temperatura 0 to +50oC (Ajuste al 40% a +70oC)
Coeficiente de Temperatura (Típico) +/- 0.01% / oC
Estabilidad Dentro de +/- 0.05% (24 horas después del calentamiento)
Vibración De acuerdo con MIL-STD-810C, Método 514
Golpes De acuerdo con MIL-STD-810C, Método 516
EMI/RFILas fuentes de alimentación lineales tienen inherentemente bajos niveles de ruido conducido y radiado. Para la mayoría de las aplicaciones en sistemas estas cumplen con los requerimientos de FCC Clase B y VDE 0871 para Clase B.
Enfriamiento De aire forzado. 20 CFM requeridos para el grado completo reducen la capacidad normal del 30% para refrescarse de la convección.
EntradaVoltaje de Entrada 100/120/220/230/240 VAC selectable +/- 10% except 230 VAC is +15%, -6%
Frecuencia de Entrada 47-63 Hz (Típico es 60 Hz. La producción de Derate 10% en 50 Hz)
Tiempo de Respuesta a Transientes 50 µsec en 50% la carga cambia para producciones valoradas hasta 6A. 100 µsec en 50% la carga cambia para producciones valoradas 6A y sobre.
Funda los RequisitosLas unidades no se funden internamente. Para la operación segura, el usuario debe proporcionar fusible de entrada de línea como por valores se rindió tabla.
SalidaRegulación de Línea 0.05% para un cambio del 10%
Regulación de la carga 0.05% para un cambio del 50%
Rizo 3.0 mV máximo Pico-a-Pico
Rango de Ajuste de CD de Salida +/- 5% Mínimo
Protección de Sobrevoltaje Todas las salidas de 5-Volt incluyen OVP integrada como un estándar (el ajuste es 6.2 V ±0.4 V) OVP está disponible opcionalmente en otros tipos
Presentir de telemando Refiérase al esquema Terminal del Bloque para la producción (s) con presentir de telemando.
Protección contra Sobrecarga 125 to 150% foldback automático de limitación de corriente
Sensores Remotos Todas unidades listaron tiene la capacidad de sensores remotos.
• Terminales de conexión fáciles de instalar. • Tight regulation: 0.05% Line; 0.05% Load• Las calificaciones de salida a +50oC• OVP integrada en modelos de 5 V y opcional en los
modelos de 12, 15 y 24 V. • Foldback Current Limiting Protección contra
Sobrecarga con Automático Recupera
• Multi-Tap AC Las Entradas• 100% Cuatro Hora Burn-in• Sírvase consultar “Términos y Condiciones, y
Políticas y Procedimientos de Ventas” • Reconocido por UL • Certificado CSA • Aprovado en CE • Certificado CB
Linear Open Frame DC Power SuppliesSilver Line Instruction Manual
Models: SLS-05-030-1T, SLS-12-017T, SLS-24-012T
Features
General Specifications
Voltage/Current Ratings
Model Number Output
SLS-05-030-1T 5V/3.0A
SLS-12-017T +12V/1.7A or +15V/1.5A
SLS-24-012T +24V/1.2A
Operating Temperature Range 0 to +50oC (Derate to 40% at +70oC)
Temperature Coefficient (Typical) +/- 0.01% / oC
Stability Within +/- 0.05% (24 hours after warm-up)
Vibration Per MIL-STD-810C, Method 514
Shock Per MIL-STD-810C, Method 516
EMI/RFI
Linear power supplies have inherently low conducted and radiated noise levels. For most system applications, these power supplies will meet the requirements of FCC Class “B” and VDE 0871 for Class “B” equipment without additional noise filtering.
Cooling Forced air. 20 CFM required for full rating Derate 30% for convection cooling.
Input Specifications
Multi Input (all units) 100/120/220/230/240 VAC selectable +/- 10% except 230 VAC is +15%, -6%
Frequency Range 47-63 Hz (Typical is 60 Hz. Derate output 10% at 50 Hz)
Transient Response Time50 µsec at 50% load changes for outputs rated up to 6A
100 µsec at 50% load changes for outputs rated 6A and over
Fuse Requirements Units are not fused internally. For safe operation, user must provide input line fuse as per values given in table.
Output Specifications
Line Regulation 0.05% for +/- 10% change
Load Regulation 0.05% for 50% change
Ripple 3.0 mV maximum peak-to-peak
DC Output Adjustment Range +/- 5% minimum
Overvoltage Protection All 5 volt outputs include built-in OVP as standard (setting is 6.2V +/- 0.4V). OVP is optionally available on other outputs
Remote Sensing All units listed have remote sensing capability.
Overload Protection 125 to 150% foldback current limit
Contact Technical Services at 1-800-377-4384 or [email protected] with any questions. Visit our website at www.solaheviduty.com
InstallationStep 1: Check the input AC connections
Step 2: Connect the AC input according to table below.
Note: SLS-12-017T can be set to a +12V to +15V range by adjusting R9 V. ADJ.
Contact Technical Services at 1-800-377-4384 or [email protected] with any questions. Visit our website at www.solaheviduty.com
Input AC Connections (See Case A)
Mechanical Dimensions: Inches (mm)
For use at: Connect Apply AC to: Primary Fuse Primary Fuse
SLS-05-030-1T SLS-12-017TSLS-24-012T
100 VAC 1-3, 2-4 1 & 5 0.5A / 125V 1.0A / 125V
120 VAC* 1-3, 2-4 1 & 4 0.5A / 125V 1.0A / 125V
220 VAC 2-3 1 & 5 0.25A / 250V 0.5A / 250V
230 VAC 2-3 1 & 4 0.25A / 250V 0.5A / 250V
240 VAC 2-3 1 & 4 0.25A / 250V 0.5A / 250V
Case A Note: The SLS models DC output can be adjusted with R9 V. ADJ.
R7 I. LIM is factory set and should not be adjusted by users.
.744" (18.9)
. 450" (11.5) MAX
0.188"(4.8 )
4.843" (123)
4.142" (105.2) 0.48" (12.2)
1.62" (41)
° MTG HOLES (6 PLACES)
AC INPUT/DC OUTPUT
OVP(OPTIONAL )
.744
"(1
8.9)
.58"
(14-
8)
.378
"(9
.6)3.
992"
( 101
.4)
3.37
0"(8
5.6)
4
+S 1 235-OU
T-S+O
UT
WEIGH T: 2.43 L BS.(1.1 KG )
PEM NUT HOLE S 6-32 MT G ( 4 P LACES)
R7I-LIM ADJ
R9V. ADJ
*Note: Unit is shipped for 120V input from factory.
Application Note: User needs to provide earth ground to power supply with either solder to Tab or using washer and nut assembly. The SLS power supply is shipped from the factory with metal shorting straps connected between the + OUT and + S terminals and the (-) OUT and (-) S terminals. This strapping configuration allows the output of the SLS to be taken from either pair of terminals. This is the standard configuration. The remote sense feature is enabled by removing the shorting straps and connecting the individual OUT and S terminals to the appropriate points of the load. If an OVP circuit is used it should be connected to the + OUT and (-) OUT terminals. The OVP should never be connected to the + S, - S terminals without the use of the shorting straps. In all cases it is critical that the terminal screws be firmly tightened.
• Easy installation with strip terminal• Adjustable output• Tight regulation: 0.05% Line; 0.05% Load• Full Output Ratings to +50oC• Built in OVP on 5 Volt Outputs• OVP Option for 12V, 15V and 24V• Foldback Current Limiting Overload Protection with
Automatic Recovery
• Multi-Tap AC Inputs• 100% Four-Hour Burn-in• Please see enclosed “Terms & Conditions and
Sales & Policies & Procedures”• UL Recognized• CSA Certified• CE Marked• CB Certified
Contacte los Servicios Técnicos en 1-847-268-6000 o [email protected] con cualquiera preguntan. Visite nuestro sitio web en www.solaheviduty. com
Contacte los Servicios Técnicos en 1-847-268-6000 o [email protected] con cualquiera preguntan. Visite nuestro sitio web en www.solaheviduty. com
Serie SL - Lineales de Salida Sencilla & Múltiple Manual de la Instrucción
Modelos: SLS-05-030-1T, SLS-12-017T, SLS-24-012T
Características
Especificaciones
InstalaciónDé un paso 1: Verifica las conexiones de entrada de C.A.
Dé un paso 2: Conecte a la entrada de C.A. según posponer abajo.
La nota: SLS-12-017T se puede establecer en el rango +12V to +15V ajustando R9 V. ADJ.
P/N A272-022 Rev. 4 (August 16, 2007)
Entrada AC Conexiones (See Caja A)
Caja A La nota: La salida DC de los modelos SLS puede ser ajustada con el R9 V. ADJ
R7 I. LIM ha sido fijada en la fabrica y no se debe ajustar por los usuarios.
.744" (18.9)
. 450" (11.5) MAX
0.188"(4.8 )
4.843" (123)
4.142" (105.2) 0.48" (12.2)
1.62" (41)
° MTG HOLES (6 PLACES)
AC INPUT/DC OUTPUT
OVP(OPTIONAL )
.744
"(1
8.9)
.58"
(14-
8)
.378
"(9
.6)3.
992"
( 101
.4)
3.37
0"(8
5.6)
4
+S 1 235-OU
T-S+O
UT
WEIGH T: 2.43 L BS.(1.1 KG )
PEM NUT HOLE S 6-32 MT G ( 4 P LACES)
R7I-LIM ADJ
R9V. ADJ
Para el uso en: Conecte Aplique AC a: El fusible primario El fusible primario
SLS-05-030-1T SLS-12-017TSLS-24-012T
100 VAC 1-3, 2-4 1 & 5 0.5A / 125V 1.0A / 125V
120 VAC* 1-3, 2-4 1 & 4 0.5A / 125V 1.0A / 125V
220 VAC 2-3 1 & 5 0.25A / 250V 0.5A / 250V
230 VAC 2-3 1 & 4 0.25A / 250V 0.5A / 250V
240 VAC 2-3 1 & 4 0.25A / 250V 0.5A / 250V
* La nota: La unidad se envía para la entrada 120V de la fábrica.
La Nota de la aplicación: Las necesidades de Usuario a proporcionar la tierra el suelo para accionar el suministro con o soldadura qa la Etiqueta o utilizar arandela y asamblea de nuez. La planta SLS se envía de fábrica con bandas metálicas de cortocircuito conectadas entre los terminales + OUT (salida) y + S y los terminales (-) OUT y (-) S. Esta configuración de bandas permite la salida desde la SLS desde cualquier par de terminales, y es la configuración estándar. La función de sensor remoto se activa al retirar las bandas de cortocircuito y conectar los terminales individuales de salida (OUT) y S con los puntos pertinentes de la carga. Si se utiliza un circuito OVP, deberá conectarse con los terminales + OUT y (-) OUT. El circuito OVP no debe conectarse nunca con los terminales + S, - S sin las bandas de cortocircuito. En todos los casos es esencial ajustar los tornillos del terminal firmemente.
Dimensiones (pulg/mm)
Voltaje/Las Calificaciones ActualesNúmero de Catálogo Salida
SLS-05-030-1T 5V/3.0A
SLS-12-017T +12V/1.7A or +15V/1.5A
SLS-24-012T +24V/1.2A
Rango de Operación de Temperatura 0 to +50oC (Ajuste al 40% a +70oC)
Coeficiente de Temperatura (Típico) +/- 0.01% / oC
Estabilidad Dentro de +/- 0.05% (24 horas después del calentamiento)
Vibración De acuerdo con MIL-STD-810C, Método 514
Golpes De acuerdo con MIL-STD-810C, Método 516
EMI/RFILas fuentes de alimentación lineales tienen inherentemente bajos niveles de ruido conducido y radiado. Para la mayoría de las aplicaciones en sistemas estas cumplen con los requerimientos de FCC Clase B y VDE 0871 para Clase B.
Enfriamiento De aire forzado. 20 CFM requeridos para el grado completo reducen la capacidad normal del 30% para refrescarse de la convección.
EntradaVoltaje de Entrada 100/120/220/230/240 VAC selectable +/- 10% except 230 VAC is +15%, -6%
Frecuencia de Entrada 47-63 Hz (Típico es 60 Hz. La producción de Derate 10% en 50 Hz)
Tiempo de Respuesta a Transientes50 µsec en 50% la carga cambia para producciones valoradas hasta 6A.
100 µsec en 50% la carga cambia para producciones valoradas 6A y sobre.
Funda los RequisitosLas unidades no se funden internamente. Para la operación segura, el usuario debe proporcionar fusible de entrada de línea como por valores se rindió tabla.
SalidaRegulación de Línea 0.05% para un cambio del 10%
Regulación de la carga 0.05% para un cambio del 50%
Rizo 3.0 mV máximo Pico-a-Pico
Rango de Ajuste de CD de Salida +/- 5% Mínimo
Protección de Sobrevoltaje Las salidas de 5 voltios incluyen OVP incorporado como estándar (el ajuste es 6.2V +/- 0.4V). OVP está opcionalmente disponible en otras salidas
Protección contra Sobrecarga 125 to 150% foldback automático de limitación de corriente
Sensores Remotos Todas unidades listaron tiene la capacidad de sensores remotos.
• Terminales de conexión fáciles de instalar. • De salida ajustable• Tight regulation: 0.05% Line; 0.05% Load• Las calificaciones de salida a +50oC• OVP integrada en modelos de 5 V y opcional en los
modelos de 12, 15 y 24 V. • Foldback Current Limiting Protección contra
Sobrecarga con Automático Recupera
• Multi-Tap AC Las Entradas• 100% Cuatro Hora Burn-in• Sírvase consultar “Términos y Condiciones, y
Políticas y Procedimientos de Ventas” adjunto.• Reconocido por UL • Certificado CSA • Aprovado en CE • Certificado CB
Linear Open Frame DC Power SuppliesSilver Line Instruction Manual
Models: SLS-05-060-1T, SLS-12-034T, SLS-24-024T
Features
Input AC Connections (See Case B)
For use at: Connect Apply AC to:
Primary Fuse(SLS-05-0601T)(SLS-12-034T)(SLS-24-024T)
100 VAC 1-3, 2-4 1 & 5 1.6A / 125V
120 VAC* 1-3, 2-4 1 & 4 1.6A / 125V
220 VAC 2-3 1 & 5 0.8A / 250V
230 VAC 2-3 1 & 4 0.8A / 250V
240 VAC 2-3 1 & 4 0.8A / 250VGeneral Specifications
Voltage/Current RatingsModel Number Output
SLS-05-060-1T +5V / 6.0 A
SLS-12-034-T +12V / 3.4 A
SLS-24-024-T +24V / 2.4 A
Operating Temperature Range 0 to +50oC (Derate to 40% at +70oC)
Temperature Coefficient (Typical) +/- 0.01% / oC
Stability Within +/- 0.05% (24 hours after warm-up)
Vibration Per MIL-STD-810C, Method 514
Shock Per MIL-STD-810C, Method 516
EMI/RFI
Linear power supplies have inherently low conducted and radiated noise levels. For most system applications, these power supplies will meet the requirements of FCC Class “B” and VDE 0871 for Class “B” equipment without additional noise filtering.
Cooling Forced air. 20 CFM required for full rating Derate 30% for convection cooling.
Input SpecificationsMulti Input (all units) 100/120/220/230/240 VAC selectable +/- 10% except 230 VAC is +15%, -6%
Frequency Range 47-63 Hz (Typical is 60 Hz. Derate output 10% at 50 Hz)
Transient Response Time 50 µsec at 50% load changes for outputs rated up to 6A
Fuse Requirements Units are not fused internally. For safe operation, user must provide input line fuse as per values given in table.
Output Specifications
Line Regulation 0.05% for +/- 10% change
Load Regulation 0.05% for 50% change
Ripple 3.0 mV maximum peak-to-peak
DC Output Adjustment Range +/- 5% minimum
Overvoltage Protection All 5 volt outputs include built-in OVP as standard (setting is 6.2 V +/- 0.4 V). OVP is optionally available on other outputs.
Remote Sensing All units listed have remote sensing capability.
Overload Protection 125 to 150% foldback current limit
Contact Technical Services at 1-800-377-4384 or [email protected] with any questions. Visit our website at www.solaheviduty.com
Contact Technical Services at 1-800-377-4384 or [email protected] with any questions. Visit our website at www.solaheviduty.com
Mechanical Dimensions: inches (mm)
Case BUse Case B1 Output Configuration for SLS-05-060-1T and SLS-12-034T.
Use Case B2 Output Configuration for SLS-24-024T.
Note: The SLS models DC output can be adjusted with R10 V. ADJ. R8 I. LIM is factory set and should not be adjusted by users.
0.72" (18.3)
4.87" (123.5)
4.118" (104.6)
0.188"(4.8)
2.5
0"
(62
.8)
1.2
8"
(32
.5)
° MTG HOLES (8 PLACES )
0.433" (11)
5.6
2"
(14
2.6
)
0.252” (6.4)
4.8
75
"(1
24
)
AC
INP
UT
/D
CO
UT
PU
TO
VP
(OP
TIO
NA
L)
0.72" (18.3)
1.28" (32.5)
MAX
.450" (11.5)
.39"(10)
4
1
23
5
-S
+OUT+S
-OUT
WEIGHT: 4 LBS.(1.8 )KG
PEM NUT HOLES6-32 MTG (4 PLACES)
4
1
23
5
+S
-OUT-S
+OUT
CASE B1
CASE B2
R10 V.ADJ
R8 I.LIM
Application Note: User needs to provide earth ground to power supply with either solder to Tab or using washer and nut assembly. The SLS power supply is shipped from the factory with metal shorting straps connected between the + OUT and + S terminals and the (-) OUT and (-) S terminals. This strapping configuration allows the output of the SLS to be taken from either pair of terminals. This is the standard configuration. The remote sense feature is enabled by removing the shorting straps and connecting the individual OUT and S terminals to the appropriate points of the load. If an OVP circuit is used it should be connected to the + OUT and (-) OUT terminals. The OVP should never be connected to the + S, - S terminals without the use of the shorting straps. In all cases it is critical that the terminal screws be firmly tightened.
*Note: Unit is shipped for 120V input from factory.
• Easy installation with strip terminal• Tight regulation: 0.05% Line; 0.05% Load• Full Output Ratings to +50oC• Built in OVP on 5 Volt Outputs• OVP Option for 12V and 24V• Foldback Current Limiting Overload Protection with
Automatic Recovery
• Multi-Tap AC Inputs• 100% Four-Hour Burn-in• Please see enclosed “Terms & Conditions and
Sales & Policies & Procedures”• UL Recognized• CSA Certified• CE Marked• CB Certified
Serie SL - Lineales de Salida Sencilla & Múltiple Manual de la Instrucción
Modelos: SLS-05-060-1T, SLS-12-034T, SLS-24-024T
Características
Entrada AC Conexiones (See Caja B)
Especificaciones
Para el uso en: Conecte Aplique AC a:
El fusible primario(SLS-05-0601T)(SLS-12-034T)(SLS-24-024T)
100 VAC 1-3, 2-4 1 & 5 1.6A / 125V
120 VAC* 1-3, 2-4 1 & 4 1.6A / 125V
220 VAC 2-3 1 & 5 0.8A / 250V
230 VAC 2-3 1 & 4 0.8A / 250V
240 VAC 2-3 1 & 4 0.8A / 250V
Contacte los Servicios Técnicos en 1-847-268-6000 o [email protected] con cualquiera preguntan. Visite nuestro sitio web en www.solaheviduty. com
Contacte los Servicios Técnicos en 1-847-268-6000 o [email protected] con cualquiera preguntan. Visite nuestro sitio web en www.solaheviduty. com
P/N A272-023 Rev. 3 (August 16, 2007)
* La nota: La unidad se envia para la entrada 120V de la fábrica.
Caja BUtilice la configuración de salida del caso B1 para SLS-05-060-1T y SLS-12-034T.
Utilice la configuración de salida del caso B2 para SLS-24-024T.
La nota: La salida DC de los modelos SLS puede ser ajustada con el R10 V. ADJ R8 I. LIM ha sido fijada en la fabrica y no se debe ajustar por los usuarios.
0.72" (18.3)
4.87" (123.5)
4.118" (104.6)
0.188"(4.8)
2.5
0"
(62
.8)
1.2
8"
(32
.5)
° MTG HOLES (8 PLACES )
0.433" (11)
5.6
2"
(14
2.6
)
0.252” (6.4)
4.8
75
"(1
24
)
AC
INP
UT
/D
CO
UT
PU
TO
VP
(OP
TIO
NA
L)
0.72" (18.3)
1.28" (32.5)
MAX
.450" (11.5)
.39"(10)
4
1
23
5
-S
+OUT+S
-OUT
WEIGHT: 4 LBS.(1.8 )KG
PEM NUT HOLES6-32 MTG (4 PLACES)
4
1
23
5
+S
-OUT-S
+OUT
CASE B1
CASE B2
R10 V.ADJ
R8 I.LIM
La Nota de la aplicación: Las necesidades de Usuario a proporcionar la tierra el suelo para accionar el suministro con o soldadura qa la Etiqueta o utilizar arandela y asamblea de nuez. La planta SLS se envía de fábrica con bandas metálicas de cortocircuito conectadas entre los terminales + OUT (salida) y + S y los terminales (-) OUT y (-) S. Esta configuración de bandas permite la salida desde la SLS desde cualquier par de terminales, y es la configuración estándar. La función de sensor remoto se activa al retirar las bandas de cortocircuito y conectar los terminales individuales de salida (OUT) y S con los puntos pertinentes de la carga. Si se utiliza un circuito OVP, deberá conectarse con los terminales + OUT y (-) OUT. El circuito OVP no debe conectarse nunca con los terminales + S, - S sin las bandas de cortocircuito. En todos los casos es esencial ajustar los tornillos del terminal firmemente.
Dimensiones (pulg/mm)Voltaje/Las Calificaciones ActualesNúmero de Catálogo Salida
SLS-05-060-1T +5V / 6.0 A
SLS-12-034-T +12V / 3.4 A
SLS-24-024-T +24V / 2.4 A
Rango de Operación de Temperatura 0 to +50oC (Ajuste al 40% a +70oC)
Coeficiente de Temperatura (Típico) +/- 0.01% / oC
Estabilidad Dentro de +/- 0.05% (24 horas después del calentamiento)
Vibración De acuerdo con MIL-STD-810C, Método 514
Golpes De acuerdo con MIL-STD-810C, Método 516
EMI/RFILas fuentes de alimentación lineales tienen inherentemente bajos niveles de ruido conducido y radiado. Para la mayoría de las aplicaciones en sistemas estas cumplen con los requerimientos de FCC Clase B y VDE 0871 para Clase B.
Enfriamiento De aire forzado. 20 CFM requeridos para el grado completo reducen la capacidad normal del 30% para refrescarse de la convección.
EntradaVoltaje de Entrada 100/120/220/230/240 VAC selectable +/- 10% except 230 VAC is +15%, -6%
Frecuencia de Entrada 47-63 Hz (Típico es 60 Hz. La producción de Derate 10% en 50 Hz)
Tiempo de Respuesta a Transientes 50 µsec en 50% la carga cambia para producciones valoradas hasta 6A.
Funda los RequisitosLas unidades no se funden internamente. Para la operación segura, el usuario debe proporcionar fusible de entrada de línea como por valores se rindió tabla.
SalidaRegulación de Línea 0.05% para un cambio del 10%
Regulación de la carga 0.05% para un cambio del 50%
Rizo 3.0 mV máximo Pico-a-Pico
Rango de Ajuste de CD de Salida +/- 5% Mínimo
Protección de Sobrevoltaje Todas las salidas de 5-Volt incluyen OVP integrada como un estándar (el ajuste es 6.2 V ±0.4 V) OVP está disponible opcionalmente en otros tipos
Presentir de telemandoRefiérase al esquema Terminal del Bloque para la producción (s) con presentir de telemando.
Protección contra Sobrecarga 125 to 150% foldback automático de limitación de corriente
• Terminales de conexión fáciles de instalar. • Tight regulation: 0.05% Line; 0.05% Load• Las calificaciones de salida a +50oC• OVP integrada en modelos de 5 V y opcional en los
modelos de 12 y 24 V. • Foldback Current Limiting Protección contra
Sobrecarga con Automático Recupera
• Multi-Tap AC Las Entradas• 100% Cuatro Hora Burn-in• Sírvase consultar “Términos y Condiciones, y
Políticas y Procedimientos de Ventas” • Reconocido por UL • Certificado CSA • Aprovado en CE • Certificado CB
Linear Open Frame DC Power SuppliesSilver Line Instruction Manual
Models: SLS-12-051T, SLS-15-045T, SLS-24-036T, SLS-05-090-1T
Features• Easyinstallationwithstripterminal• Tightregulation:0.05%Line;0.05%Load• FullOutputRatingsto+50oC• BuiltinOVPon5VoltOutputs• OVPOptionfor12V,15Vand24V• FoldbackCurrentLimitingOverloadProtection
withAutomaticRecovery
Input AC Connections (See Case C)
Mechanical Dimensions: Inches (mm)
Case C Note:TheDCoutputcanbeadjustedwithV.ADJ.
I. LIM is factory set on all models and should not be adjusted by users.
• Multi-TapACInputs• 100%Four-HourBurn-in• LimitedWarrantyfortwoyears• ULRecognized• CSACertified• CEMarked• CBCertified
General Specifications
Voltage/Current RatingsModelNumbers Output
SLS-12-051T 12V/5.1A
SLS-15-045T 15V/4.5A
SLS-24-036T 24V/3.6A
SLS-05-090-1T 5V/9.0A
OperatingTemperatureRange 0to+50oC(Derateto40%at+70oC)
TemperatureCoefficient(Typical) +/-0.01%/oC
Stability Within+/-0.05%(24hoursafterwarm-up)
Vibration PerMIL-STD-810C,Method514
Shock PerMIL-STD-810C,Method516
EMI/RFI Linearpowersupplieshaveinherentlylowconductedandradiatednoiselevels.Formostsystemapplications,thesepowersupplieswillmeettherequirementsofFCCClass“B”andVDE0871forClass“B”equipmentwithoutadditionalnoisefiltering.
Cooling Forcedair.20CFMrequiredforfullratingDerate30%forconvectioncooling.
Input SpecificationsMultiInput(allunits) 100/120/220/230/240VACselectable+/-10%except230VACis+15%,-6%
FrequencyRange 47-63Hz(Typicalis60Hz.Derateoutput10%at50Hz)
TransientResponseTime 50µat50%loadchangesforoutputsratedupto6A
100µat50%loadchangesforoutputsrated6Aandover.
FuseRequirements Unitsarenotfusedinternally.Forsafeoperation,usermustprovideinputlinefuseaspervaluesgivenintable.
Output Specifications
LineRegulation 0.05%for+/-10%change
LoadRegulation 0.05%for50%change
Ripple 3.0mVmaximumpeak-to-peak
DCOutputAdjustmentRange +/-5%minimum(CheckVoltage & Current ADJ Placement Diagrams)
OvervoltageProtection All5voltoutputsincludebuilt-inOVPasstandard(settingis6.2V+/-0.4V).OVPisoptionallyavailableonotheroutputs.
RemoteSensing Allunitslistedhaveremotesensingcapability.
OverloadProtection 125to150%foldbackcurrentlimit
7.00" (178)
6.250" (158.8)
AC INPUT/DC OUTPUT
.50" (12.7)
.50" (12.9)
.75” (19.1)
4.8
7"
(12
3.7
)2
.75
"( 6
9.9
)
1.2
48
"( 3
1.7
)
.38" (9.6)
4.1
25
"(1
04
.8)
OVP (OPTIONAL)° MTG HOLES (12 PLACES)
1.248" (31.7) .75" (19.1)
188"(4.8)
MAX
.551" (14)
+S41 235 -OU
T-S+
OU
T
WEIGHT: 7.28 LBS.(3.3 KG)
PEM NUT HOLES8-32 MTG (4 PLACES)
Top View
Case C
Please See
Voltage &
CurrentADJ
PlacementDiagrams
Contact Technical Services at 1-800-377-4384 or [email protected] with any questions. Visit our website at www.solaheviduty.com
*Note:Unitisshippedfor120Vinputfromfactory.
**PrimaryFuseforSLS-24-036T
For use at: Connect Apply AC to: Primary Fuse Primary Fuse**100VAC 1-3,2-4 1&5 1.6A/125V 2A/125V
120VAC* 1-3,2-4 1&4 1.6A/125V 2A/125V
220VAC 2-3 1&5 0.8A/250V 1A/250V
230VAC 2-3 1&4 0.8A/250V 1A/250V
240VAC 2-3 1&4 0.8A/250V 1A/250V
Application Note:UserneedstoprovideearthgroundtopowersupplywitheithersoldertoTaborusingwasherandnutassembly.TheSLSpowersupplyisshippedfromthefactorywithmetalshortingstrapsconnectedbetweenthe+OUTand+Sterminalsandthe(-)OUTand(-)Sterminals.ThisstrappingconfigurationallowstheoutputoftheSLStobetakenfromeitherpairofterminals.Thisisthestandardconfiguration.Theremote sensefeatureisenabledbyremovingtheshortingstrapsandconnectingtheindividualOUTandSterminalstotheappropriatepointsoftheload.IfanOVPcircuitisuseditshouldbeconnectedtothe+OUTand(-)OUTterminals.TheOVPshouldneverbeconnectedtothe+S,-Sterminalswithouttheuseoftheshortingstraps.Inallcasesitiscriticalthattheterminalscrewsbefirmly tightened.
Voltage & CurrentADJ Placement
Diagrams
R11V. ADJ
R5I.LIM
R13V. ADJ
R6I.LIM
R11V. ADJ
R5I.LIM
SLS-12-051T
SLS-24-036T
SLS-15-045T
SLS-05-090-1T
Serie SL - Lineales de Salida Sencilla & Múltiple Manual de la Instrucción Modelos: SLS-12-051T, SLS-15-045T,
SLS-24-036T, SLS-05-090-1TCaracterísticas
•Terminalesdeconexiónfácilesdeinstalar.•Tightregulation:0.05%Line;0.05%Load•Lascalificacionesdesalidaa+50oC•OVPintegradaenmodelosde5Vyopcionalenlos
modelosde12,15y24V.•FoldbackCurrentLimitingProteccióncontra
SobrecargaconAutomáticoRecupera
Entrada AC Conexiones (See Caja C)
Caja CLanota:LasalidadelaC.C.sepuedeajustarconelajustedelV.ADJ.
I. LIM ha sido fijada en la fabrica y no se debe ajustar por los usuarios.
•Multi-TapACLasEntradas•100%CuatroHoraBurn-in•Dosañosdegarantía.•ReconocidoporUL•CertificadoCSA•AprovadoenCE•CertificadoCB
Especificaciones
Contacte los Servicios Técnicos en 1-847-268-6000 o [email protected] con cualquiera preguntan. Visite nuestro sitio web en www.solaheviduty. com
*Lanota:Launidadseenvíaparalaentrada120Vdelafábrica.
**ElfusibleprimarioforSLS-24-036T
Para el uso en: Conecte Aplique AC a: El fusible primario El fusible primario**100VAC 1-3,2-4 1&5 1.6A/125V 2A/125V
120VAC* 1-3,2-4 1&4 1.6A/125V 2A/125V
220VAC 2-3 1&5 0.8A/250V 1A/250V
230VAC 2-3 1&4 0.8A/250V 1A/250V
240VAC 2-3 1&4 0.8A/250V 1A/250V
P/N A272-005 Rev. 3 (April 20, 2006)
La Nota de la aplicación:LasnecesidadesdeUsuarioaproporcionarlatierraelsueloparaaccionarelsuministroconosoldaduraqalaEtiquetaoutilizararandelayasambleadenuez.LaplantaSLSseenvíadefábricaconbandasmetálicasdecortocircuitoconectadasentrelosterminales+OUT(salida)y+Sylosterminales(-)OUTy(-)S.EstaconfiguracióndebandaspermitelasalidadesdelaSLSdesdecualquierpardeterminales,yeslaconfiguraciónestándar.Lafuncióndesensorremotoseactivaalretirarlasbandasdecortocircuitoyconectarlosterminalesindividualesdesalida(OUT)ySconlospuntospertinentesdelacarga.SiseutilizauncircuitoOVP,deberáconectarseconlosterminales+OUTy(-)OUT.ElcircuitoOVPnodebeconectarsenuncaconlosterminales+S,-Ssinlasbandasdecortocircuito.Entodosloscasosesesencialajustarlostornillosdelterminalfirmemente.
Dimensiones (pulg/mm)
Voltaje/Las Calificaciones ActualesNúmerodeCatálogo Salida1
SLS-12-051T 12V/5.1A
SLS-15-045T 15V/4.5A
SLS-24-036T 24V/3.6A
SLS-05-090-1T 5V/9.0A
RangodeOperacióndeTemperatura 0to+50oC(Ajusteal40%a+70oC)
CoeficientedeTemperatura(Típico) +/-0.01%/oC
Estabilidad Dentrode+/-0.05%(24horasdespuésdelcalentamiento)
Vibración DeacuerdoconMIL-STD-810C,Método514
Golpes DeacuerdoconMIL-STD-810C,Método516
EMI/RFI Lasfuentesdealimentaciónlinealestieneninherentementebajosnivelesderuidoconducidoyradiado.ParalamayoríadelasaplicacionesensistemasestascumplenconlosrequerimientosdeFCCClaseByVDE0871paraClaseB.
Enfriamiento Deaireforzado.20CFMrequeridosparaelgradocompletoreducenlacapacidadnormaldel30%pararefrescarsedelaconvección.
EntradaVoltajedeEntrada 100/120/220/230/240VACselectable+/-10%except230VACis+15%,-6%
FrecuenciadeEntrada 47-63Hz(Típicoes60Hz.LaproduccióndeDerate10%en50Hz)
TiempodeRespuestaaTransientes 50µen50%lacargacambiaparaproduccionesvaloradashasta6A.100µen50%lacargacambiaparaproduccionesvaloradas6Aysobre.
FundalosRequisitos Lasunidadesnosefundeninternamente.Paralaoperaciónsegura,elusuariodebeproporcionarfusibledeentradadelíneacomoporvaloresserindiótabla.
SalidaRegulacióndeLínea 0.05%parauncambiodel10%
Regulacióndelacarga 0.05%parauncambiodel50%
Rizo 3.0mVmáximoPico-a-Pico
RangodeAjustedeCDdeSalida +/-5%Mínimo(CheckVoltage & Current ADJ Placement Diagrams)
ProteccióndeSobrevoltaje Todaslassalidasde5-VoltincluyenOVPintegradacomounestándar(elajustees6.2V±0.4V)OVPestádisponibleopcionalmenteenotrostipos
Presentirdetelemando RefiérasealesquemaTerminaldelBloqueparalaproducción(s)conpresentirdetelemando.
ProteccióncontraSobrecarga 125to150%foldbackautomáticodelimitacióndecorriente
SensoresRemotos Todasunidadeslistarontienelacapacidaddesensoresremotos.
7.00" (178)
6.250" (158.8)
AC INPUT/DC OUTPUT
.50" (12.7)
.50" (12.9)
.75” (19.1)
4.8
7"
(12
3.7
)2
.75
"( 6
9.9
)
1.2
48
"( 3
1.7
)
.38" (9.6)
4.1
25
"(1
04
.8)
OVP (OPTIONAL)° MTG HOLES (12 PLACES)
1.248" (31.7) .75" (19.1)
188"(4.8)
MAX
.551" (14)
+S41 235 -OU
T-S+
OU
T
WEIGHT: 7.28 LBS.(3.3 KG)
PEM NUT HOLES8-32 MTG (4 PLACES)
Top View
Case C
Please See
Voltage &
CurrentADJ
PlacementDiagrams
Voltage & CurrentADJ Placement
Diagrams
R11V. ADJ
R5I.LIM
R13V. ADJ
R6I.LIM
R11V. ADJ
R5I.LIM
SLS-12-051T
SLS-24-036T
SLS-15-045T
SLS-05-090-1T
Linear Open Frame DC Power SuppliesSilver Line Instruction Manual
Models: SLS-05-120-1T, SLS-12-068T, SLS-15-060T, SLS-24-048T
Features
Input AC Connections (See Case I2)
For use at: Connect Apply AC to:
Primary FuseSLS-05-120-1T
Primary FuseSLS-15-060TSLS-12-068T
Primary FuseSLS-24-048T
100 VAC 1-3, 2-4 1 & 5 2 A / 125 V 2.5 A / 125V 3.0A / 125V
120 VAC* 1-3, 2-4 1 & 4 2 A / 125 V 2.5 A / 125V 3.0A / 125V
220 VAC 2-3 1 & 5 1 A / 250 V 1.25A / 250V 1.5A / 250V
230 VAC 2-3 1 & 4 1 A / 250 V 1.25A / 250V 1.5A / 250V
240 VAC 2-3 1 & 4 1 A / 250 V 1.25A / 250V 1.5A / 250V
General Specifications
Voltage/Current RatingsModel Numbers Output (Volts) Output (Amps)
SLS-05-120-1T 5 12.0
SLS-12-068T 12 6.8
SLS-15-060T 15 6.0
SLS-24-048T 24 4.8
Operating Temperature Range 0 to +50oC (Derate to 40% at +70oC)
Temperature Coefficient (Typical) +/- 0.01% / oC
Stability Within +/- 0.05% (24 hours after warm-up)
Vibration Per MIL-STD-810C, Method 514
Shock Per MIL-STD-810C, Method 516
EMI/RFI
Linear power supplies have inherently low conducted and radiated noise levels. For most system applications, these power supplies will meet the requirements of FCC Class “B” and VDE 0871 for Class “B” equipment without additional noise filtering.
Cooling Forced air. 20 CFM required for full rating Derate 30% for convection cooling.
Input SpecificationsMulti Input (all units) 100/120/220/230/240 VAC selectable +/- 10% except 230 VAC is +15%, -6%
Frequency Range 47-63 Hz (Typical is 60 Hz. Derate output 10% at 50 Hz)
Transient Response Time50 µsec at 50% load changes for outputs rated up to 6A
100 µsec at 50% load changes for outputs rated 6A and over.
Fuse Requirements Units are not fused internally. For safe operation, user must provide input line fuse as per values given in table.
Output Specifications
Line Regulation 0.05% for +/- 10% change
Load Regulation 0.05% for 50% change
Ripple 3.0 mV maximum peak-to-peak
DC Output Adjustment Range +/- 5% minimum
Overvoltage Protection All 5 volt outputs include built-in OVP standard (setting is 6.2V +/- 0.4 V). OVP is optionally available on other outputs
Remote Sensing All units have remote sensing capability.
Overload Protection 125 to 150% foldback current limit Contact Technical Services at 1-800-377-4384 or [email protected] with any questions. Visit our website at www.solaheviduty.com
*Note: Unit is shipped for 120V input from factory.
Mechanical Dimensions: Inches (mm)
OVP (OPTIONAL)
8.00" (203). 512" (13)
9.00" (229)AC INPUT/DC OUTPUT
°MTG HOLES (12 PLACES). 473" (12)
. 188"(4.8 )
. 75" (19)
4.87
"(124
)2.75
"( 70)
1.25
0"(32)
4.12
5"(105
)
1.250" (32)
.39"
(10)
. 75" (19)
MAX
.551" (14)
Case I1
Case I2
Case I3
Case I4
WEIGHT: 7. 5 LBS.(3.4 KG)
+O
UT
41 235
+O
UT
-O
UT
-S
+S-S-O
UT
+S
AC Input 12V5V
+12V C
OM
+5V
+5V
-12V-12V-12V
+5V
+12V
+12V
-S +O
UT
+S+S
-S -OU
T
-S+S+O
UT
PEM NU T H OLES8-32 MT G ( 4 P LACES)
+S
+O
UT
-S-O
UT
AC Input
41 235
+O
UT
+O
UT
-O
UT
-S
+S-S-O
UT
+S
AC Input 12/15V
41 235
12/15V
AC Input41 235
R13I.LIM
R14V.ADJ
OVP (OPTIONAL)
8.00" (203). 512" (13)
9.00" (229)AC INPUT/DC OUTPUT
°MTG HOLES (12 PLACES)
. 473" (12). 188"(4.8 )
. 75" (19)
4.8
7"
(12
4)
2.7
5"
( 70
)
1.2
50
"(3
2)
4.1
25
"( 1
05
)
1.250" (32)
.39
"(1
0)
. 75" (19)
MAX
. 551" (14)
Case I1
Case I2
Case I3
Case I4
WEIGHT: 7. 5 LBS.(3.4 KG)
+O
UT
41 235
+O
UT
-O
UT
-S
+S-S-O
UT
+S
AC Input 12V5V
+1
2V CO
M
+5
V+
5V
-12
V-1
2V
-12
V
+5
V
+1
2V
+1
2V
-S +O
UT
+S
+S
-S -OU
T
-S+S
+O
UT
PEM NUT HOLES8-32 MTG (4 PLACES)
+S
+O
UT
-S-O
UT
AC Input
41 235
+O
UT
+O
UT
-O
UT
-S
+S
-S-O
UT
+S
AC Input 12/15V
41 235
12/15V
AC Input41 235
Please See
Voltage &
CurrentADJ
PlacementDiagrams
Case I2 Note: The SLS models DC output can be adjusted with R14 V. ADJ.
R13 I. LIM is factory set and should not be adjusted by users.
Application Note: User needs to provide earth ground to power supply with either solder to Tab or using washer and nut assembly. The SLS power supply is shipped from the factory with metal shorting straps connected between the + OUT and + S terminals and the (-) OUT and (-) S terminals. This strapping configuration allows the output of the SLS to be taken from either pair of terminals. This is the standard configuration. The remote sense feature is enabled by removing the shorting straps and connecting the individual OUT and S terminals to the appropriate points of the load. If an OVP circuit is used it should be connected to the + OUT and (-) OUT terminals. The OVP should never be connected to the + S, - S terminals without the use of the shorting straps. In all cases it is critical that the terminal screws be firmly tightened.
• Easy installation with strip terminal• Tight regulation: 0.05% Line; 0.05% Load• Full Output Ratings to +50oC• Built in OVP on 5 Volt Outputs• OVP Option for 12V, 15V and 24V• Foldback Current Limiting Overload Protection with
Automatic Recovery
• Multi-Tap AC Inputs• 100% Four-Hour Burn-in• Please see enclosed “Terms & Conditions and
Sales & Policies & Procedures”• UL Recognized• CSA Certified• CE Marked• CB Certified
Serie SL - Lineales de Salida Sencilla & Múltiple Manual de la Instrucción
Modelos: SLS-05-120-1T, SLS-12-068T, SLS-15-060T, SLS-24-048T
Características
Entrada AC Conexiones (See Caja I2)
Especificaciones
P/N A272-025 Rev. 4 (August 16, 2007)
Contacte los Servicios Técnicos en 1-847-268-6000 o [email protected] con cualquiera preguntan. Visite nuestro sitio web en www.solaheviduty. com
Para el uso en:: Conecte Aplique
AC a:
El fusible primario
SLS-05-120-1T
El fusible primario
SLS-15-060TSLS-12-068T
El fusible primario
SLS-24-048T
100 VAC 1-3, 2-4 1 & 5 2 A / 125 V 2.5 A / 125V 3.0A / 125V
120 VAC* 1-3, 2-4 1 & 4 2 A / 125 V 2.5 A / 125V 3.0A / 125V
220 VAC 2-3 1 & 5 1 A / 250 V 1.25A / 250V 1.5A / 250V
230 VAC 2-3 1 & 4 1 A / 250 V 1.25A / 250V 1.5A / 250V
240 VAC 2-3 1 & 4 1 A / 250 V 1.25A / 250V 1.5A / 250V
* La nota: La unidad se envia para la entrada 120V de la fábrica.
OVP (OPTIONAL)
8.00" (203). 512" (13)
9.00" (229)AC INPUT/DC OUTPUT
°MTG HOLES (12 PLACES). 473" (12)
. 188"(4.8 )
. 75" (19)
4.87
"(124
)2.75
"( 70)
1.25
0"(32)
4.12
5"(105
)
1.250" (32)
.39"
(10)
. 75" (19)
MAX
.551" (14)
Case I1
Case I2
Case I3
Case I4
WEIGHT: 7. 5 LBS.(3.4 KG)
+O
UT
41 235
+O
UT
-O
UT
-S
+S-S-O
UT
+S
AC Input 12V5V
+12V C
OM
+5V
+5V
-12V-12V-12V
+5V
+12V
+12V
-S +O
UT
+S+S
-S -OU
T
-S+S+O
UT
PEM NU T H OLES8-32 MT G ( 4 P LACES)
+S
+O
UT
-S-O
UT
AC Input
41 235
+O
UT
+O
UT
-O
UT
-S
+S-S-O
UT
+S
AC Input 12/15V
41 235
12/15V
AC Input41 235
R13I.LIM
R14V.ADJ
La Nota de la aplicación: Las necesidades de Usuario a proporcionar la tierra el suelo para accionar el suministro con o soldadura qa la Etiqueta o utilizar arandela y asamblea de nuez. La planta SLS se envía de fábrica con bandas metálicas de cortocircuito conectadas entre los terminales + OUT (salida) y + S y los terminales (-) OUT y (-) S. Esta configuración de bandas permite la salida desde la SLS desde cualquier par de terminales, y es la configuración estándar. La función de sensor remoto se activa al retirar las bandas de cortocircuito y conectar los terminales individuales de salida (OUT) y S con los puntos pertinentes de la carga. Si se utiliza un circuito OVP, deberá conectarse con los terminales + OUT y (-) OUT. El circuito OVP no debe conectarse nunca con los terminales + S, - S sin las bandas de cortocircuito. En todos los casos es esencial ajustar los tornillos del terminal firmemente.
Dimensiones (pulg/mm)Voltaje/Las Calificaciones ActualesNúmero de Catálogo Salida (Voltaje) Salida (Amps)
SLS-05-120-1T 5 12.0
SLS-12-068T 12 6.8
SLS-15-060T 15 6.0
SLS-24-048T 24 4.8
Rango de Operación de Temperatura 0 to +50oC (Ajuste al 40% a +70oC)
Coeficiente de Temperatura (Típico) +/- 0.01% / oC
Estabilidad Dentro de +/- 0.05% (24 horas después del calentamiento)
Vibración De acuerdo con MIL-STD-810C, Método 514
Golpes De acuerdo con MIL-STD-810C, Método 516
EMI/RFILas fuentes de alimentación lineales tienen inherentemente bajos niveles de ruido conducido y radiado. Para la mayoría de las aplicaciones en sistemas estas cumplen con los requerimientos de FCC Clase B y VDE 0871 para Clase B.
Enfriamiento De aire forzado. 20 CFM requeridos para el grado completo reducen la capacidad normal del 30% para refrescarse de la convección.
EntradaVoltaje de Entrada 100/120/220/230/240 VAC selectable +/- 10% except 230 VAC is +15%, -6%
Frecuencia de Entrada 47-63 Hz (Típico es 60 Hz. La producción de Derate 10% en 50 Hz)
Tiempo de Respuesta a Transientes 50 µsec en 50% la carga cambia para producciones valoradas hasta 6A. 100 µsec en 50% la carga cambia para producciones valoradas 6A y sobre.
Funda los RequisitosLas unidades no se funden internamente. Para la operación segura, el usuario debe proporcionar fusible de entrada de línea como por valores se rindió tabla.
SalidaRegulación de Línea 0.05% para un cambio del 10%
Regulación de la carga 0.05% para un cambio del 50%
Rizo 3.0 mV máximo Pico-a-Pico
Rango de Ajuste de CD de Salida +/- 5% Mínimo
Protección de Sobrevoltaje Todas las salidas de 5-Volt incluyen OVP integrada como un estándar (el ajuste es 6.2 V ±0.4 V) OVP está disponible opcionalmente en otros tipos
Protección contra Sobrecarga 125 to 150% foldback automático de limitación de corriente
Sensores Remotos Todas unidades listaron tiene la capacidad de sensores remotos.
OVP (OPTIONAL)
8.00" (203). 512" (13)
9.00" (229)AC INPUT/DC OUTPUT
°MTG HOLES (12 PLACES)
. 473" (12). 188"(4.8 )
. 75" (19)
4.8
7"
(12
4)
2.7
5"
( 70
)
1.2
50
"(3
2)
4.1
25
"( 1
05
)
1.250" (32)
.39
"(1
0)
. 75" (19)
MAX
. 551" (14)
Case I1
Case I2
Case I3
Case I4
WEIGHT: 7. 5 LBS.(3.4 KG)
+O
UT
41 235
+O
UT
-O
UT
-S
+S-S-O
UT
+S
AC Input 12V5V
+1
2V CO
M
+5
V+
5V
-12
V-1
2V
-12
V
+5
V
+1
2V
+1
2V
-S +O
UT
+S
+S
-S -OU
T
-S+S
+O
UT
PEM NUT HOLES8-32 MTG (4 PLACES)
+S
+O
UT
-S-O
UT
AC Input
41 235
+O
UT
+O
UT
-O
UT
-S
+S
-S-O
UT
+S
AC Input 12/15V
41 235
12/15V
AC Input41 235
Please See
Voltage &
CurrentADJ
PlacementDiagrams
Caja I2 La nota: La salida DC de los modelos SLS puede ser ajustada con el R14 V. ADJ
R13 I. LIM ha sido fijada en la fabrica y no se debe ajustar por los usuarios.
• Terminales de conexión fáciles de instalar. • De salida ajustable de 12V a 15V• Tight regulation: 0.05% Line; 0.05% Load• Las calificaciones de salida a +50oC• OVP integrada en modelos de 5 V y opcional en los
modelos de 12, 15 y 24 V. • Foldback Current Limiting Protección contra
Sobrecarga con Automático Recupera
• Multi-Tap AC Las Entradas• 100% Cuatro Hora Burn-in• Sírvase consultar “Términos y Condiciones, y
Políticas y Procedimientos de Ventas” • Reconocido por UL • Certificado CSA • Aprovado en CE • Certificado CB
Linear Open Frame DC Power SuppliesSilver Line Instruction Manual
Model: SLS-24-072T
Features
Input AC Connections (See Case K)
For use at: Connect Apply AC to: Primary Fuse
100 VAC 1-3, 2-4 1 & 5 4.0 A / 125 V
120 VAC* 1-3, 2-4 1 & 4 4.0 A / 125 V
220 VAC 2-3 1 & 5 2 A / 250 V
230 VAC 2-3 1 & 4 2 A / 250 V
240 VAC 2-3 1 & 4 2 A / 250 V
General Specifications
Voltage/Current RatingsModel Number Output
SLS-24-072T 24 V / 7.2 A
Operating Temperature Range 0 to +50oC (Derate to 40% at +70oC)
Temperature Coefficient (Typical) +/- 0.01% / oC
Stability Within +/- 0.05% (24 hours after warm-up)
Vibration Per MIL-STD-810C, Method 514
Shock Per MIL-STD-810C, Method 516
EMI/RFI
Linear power supplies have inherently low conducted and radiated noise levels. For most system applications, these power supplies will meet the requirements of FCC Class “B” and VDE 0871 for Class “B” equipment without additional noise filtering.
Cooling Forced air. 20 CFM required for full rating Derate 30% for convection cooling.
Input SpecificationsMulti Input (all units) 100/120/220/230/240 VAC selectable +/- 10% except 230 VAC is +15%, -6%
Frequency Range 47-63 Hz (Typical is 60 Hz. Derate output 10% at 50 Hz)
Transient Response Time 100 µsec for 50 to 100% load changes.
Fuse Requirements Units are not fused internally. For safe operation, user must provide input line fuse as per values given in table.
Output Specifications
Line Regulation 0.05% for +/- 10% line change
Load Regulation 0.05% for 50% load change
Ripple 3.0 mV maximum peak-to-peak
DC Output Adjustment Range +/- 5% minimum
Overvoltage Protection OVP is optionally available
Remote Sensing Standard built-in open sense load protection.
Overload Protection 125 to 150% foldback current limit
Contact Technical Services at 1-800-377-4384 or [email protected] with any questions. Visit our website at www.solaheviduty.com
Contact Technical Services at 1-800-377-4384 or [email protected] with any questions. Visit our website at www.solaheviduty.com
*Note: Unit is shipped for 120V input from factory.
Mechanical Dimensions: Inches (mm)
Case K Note: The SLS models DC output can be adjusted with R14 V. ADJ.
R5 I. LIM is factory set and should not be adjusted by users.
OVP (OPTIONAL)
12.99" (330).49" (12.5)
13.98" (355)AC INPUT/DC OUTPUT
°MTG HOLES (12 PLACES)
.49" (12.5) .188" (4.8)
.75" (19)
4.8
7"
(12
4)
2.7
5"
(70
)
1.2
50
"(3
2)
4.1
25
"(1
05
)
1.250" (32)
.49" (12.5)
.75" (19)
MAX
.59" (15)
WEIGHT: 7.5 LBS.(3.4 KG)
+S+O
UT
-S -O
UT
4 12 3 5
AC Input
PEM NUT HOLES8-32 MTG (4 PLACES)
R14V.ADJ
R5I.LIM
Application Note: User needs to provide earth ground to power supply with either solder to Tab or using washer and nut assembly. The SLS power supply is shipped from the factory with metal shorting straps connected between the + OUT and + S terminals and the (-) OUT and (-) S terminals. This strapping configuration allows the output of the SLS to be taken from either pair of terminals. This is the standard configuration. The remote sense feature is enabled by removing the shorting straps and connecting the individual OUT and S terminals to the appropriate points of the load. If an OVP circuit is used it should be connected to the + OUT and (-) OUT terminals. The OVP should never be connected to the + S, - S terminals without the use of the shorting straps. In all cases it is critical that the terminal screws be firmly tightened.
• Easy installation with strip terminal• Tight regulation: 0.05% Line; 0.05% Load• Full Output Ratings to +50oC• OVP Option Available • Foldback Current Limiting Overload Protection with
Automatic Recovery
• Multi-Tap AC Inputs• 100% Four-Hour Burn-in• Please see enclosed “Terms & Conditions and
Sales & Policies & Procedures”• UL Recognized• CSA Certified• CE Marked• CB Certified
Serie SL - Lineales de Salida Sencilla & Múltiple Manual de la Instrucción
Modelos: SLS-24-072T
Características
Entrada AC Conexiones (See Caja K)
Especificaciones
Para el uso en: Conecte Aplique AC a: El fusible primario
100 VAC 1-3, 2-4 1 & 5 4.0 A / 125 V
120 VAC* 1-3, 2-4 1 & 4 4.0 A / 125 V
220 VAC 2-3 1 & 5 2 A / 250 V
230 VAC 2-3 1 & 4 2 A / 250 V
240 VAC 2-3 1 & 4 2 A / 250 V
P/N A272-026 Rev. 3 (August 16, 2007)
Contacte los Servicios Técnicos en 1-847-268-6000 o [email protected] con cualquiera preguntan. Visite nuestro sitio web en www.solaheviduty. com
Contacte los Servicios Técnicos en 1-847-268-6000 o [email protected] con cualquiera preguntan. Visite nuestro sitio web en www.solaheviduty. com
* La nota: La unidad se envia para la entrada 120V de la fábrica.
Caja K La nota: La salida DC de los modelos SLS puede ser ajustada con el R14 V. ADJ
R5 I. LIM ha sido fijada en la fabrica y no se debe ajustar por los usuarios.
La Nota de la aplicación: Las necesidades de Usuario a proporcionar la tierra el suelo para accionar el suministro con o soldadura qa la Etiqueta o utilizar arandela y asamblea de nuez. La planta SLS se envía de fábrica con bandas metálicas de cortocircuito conectadas entre los terminales + OUT (salida) y + S y los terminales (-) OUT y (-) S. Esta configuración de bandas permite la salida desde la SLS desde cualquier par de terminales, y es la configuración estándar. La función de sensor remoto se activa al retirar las bandas de cortocircuito y conectar los terminales individuales de salida (OUT) y S con los puntos pertinentes de la carga. Si se utiliza un circuito OVP, deberá conectarse con los terminales + OUT y (-) OUT. El circuito OVP no debe conectarse nunca con los terminales + S, - S sin las bandas de cortocircuito. En todos los casos es esencial ajustar los tornillos del terminal firmemente.
Dimensiones (pulg/mm)
Voltaje/Las Calificaciones ActualesNúmero de Catálogo Salida 1
SLS-24-072T 24 V / 7.2 A
Rango de Operación de Temperatura 0 to +50oC (Ajuste al 40% a +70oC)
Coeficiente de Temperatura (Típico) +/- 0.01% / oC
Estabilidad Dentro de +/- 0.05% (24 horas después del calentamiento)
Vibración De acuerdo con MIL-STD-810C, Método 514
Golpes De acuerdo con MIL-STD-810C, Método 516
EMI/RFILas fuentes de alimentación lineales tienen inherentemente bajos niveles de ruido conducido y radiado. Para la mayoría de las aplicaciones en sistemas estas cumplen con los requerimientos de FCC Clase B y VDE 0871 para Clase B.
Enfriamiento De aire forzado. 20 CFM requeridos para el grado completo reducen la capacidad normal del 30% para refrescarse de la convección.
EntradaVoltaje de Entrada 100/120/220/230/240 VAC selectable +/- 10% except 230 VAC is +15%, -6%
Frecuencia de Entrada 47-63 Hz (Típico es 60 Hz. La producción de Derate 10% en 50 Hz)
Tiempo de Respuesta a Transientes 100 µsec para 50% en 100% la carga cambia.
Funda los RequisitosLas unidades no se funden internamente. Para la operación segura, el usuario debe proporcionar fusible de entrada de línea como por valores se rindió tabla.
SalidaRegulación de Línea 0.05% para un cambio de línea de +/-10%
Regulación de la carga 0.05% para un cambio de carga de 50%
Rizo 3.0 mV máximo Pico-a-Pico
Rango de Ajuste de DC de Salida +/- 5% Mínimo
Protección de Sobrevoltaje Opción de OVP Disponible
Presentir de telemando Refiérase al esquema Terminal del Bloque para la producción (s) con presentir de telemando.
Protección contra Sobrecarga 125 to 150% foldback automático de limitación de corriente
Sensores Remotos La protección abierta, incorporada y uniforme de la carga del sentido
• Terminales de conexión fáciles de instalar. • Tight regulation: 0.05% Line; 0.05% Load• Las calificaciones de salida a +50oC• Opción de OVP Disponible • Foldback Current Limiting Protección contra
Sobrecarga con Automático Recupera
• Multi-Tap AC Las Entradas• 100% Cuatro Hora Burn-in• Sírvase consultar “Términos y Condiciones, y
Políticas y Procedimientos de Ventas” • Reconocido por UL • Certificado CSA • Aprovado en CE • Certificado CB
OVP (OPTIONAL)
12.99" (330).49" (12.5)
13.98" (355)AC INPUT/DC OUTPUT
°MTG HOLES (12 PLACES)
.49" (12.5) .188" (4.8)
.75" (19)
4.8
7"
(12
4)
2.7
5"
(70
)
1.2
50
"(3
2)
4.1
25
"(1
05
)
1.250" (32)
.49" (12.5)
.75" (19)
MAX
.59" (15)
WEIGHT: 7.5 LBS.(3.4 KG)
+S+O
UT
-S -O
UT
4 12 3 5
AC Input
PEM NUT HOLES8-32 MTG (4 PLACES)
R14V.ADJ
R5I.LIM
Linear Open Frame DC Power SuppliesSilver Line Instruction Manual
Model: SLS-24-120T
Features
Input AC Connections (See Case L)
For use at: Connect Apply AC to: Primary Fuse
100 VAC 1-3, 2-4 1 & 5 6.0 A / 125 V
120 VAC* 1-3, 2-4 1 & 4 6.0 A / 125 V
220 VAC 2-3 1 & 5 3.0 A / 250 V
230 VAC 2-3 1 & 4 3.0 A / 250 V
240 VAC 2-3 1 & 4 3.0 A / 250 V
General Specifications
Voltage/Current RatingsModel Number Output 1
SLS-24-120T 24 V / 12 A
Operating Temperature Range 0 to +50oC (Derate to 40% at +70oC)
Temperature Coefficient (Typical) +/- 0.01% / oC
Stability Within +/- 0.05% (24 hours after warm-up)
Vibration Per MIL-STD-810C, Method 514
Shock Per MIL-STD-810C, Method 516
EMI/RFI
Linear power supplies have inherently low conducted and radiated noise levels. For most system applications, these power supplies will meet the requirements of FCC Class “B” and VDE 0871 for Class “B” equipment without additional noise filtering.
Cooling Forced air. 20 CFM required for full rating Derate 30% for convection cooling.
Input SpecificationsMulti Input (all units) 100/120/220/230/240 VAC selectable +/- 10% except 230 VAC is +15%, -6%
Frequency Range 47-63 Hz (Typical is 60 Hz. Derate output 10% at 50 Hz)
Transient Response Time 100 µsec for 50 to 100% load changes
Fuse Requirements Units are not fused internally. For safe operation, user must provide input line fuse as per values given in table.
Output Specifications
Line Regulation 0.05% for +/- 10% change
Load Regulation 0.05% for 50% change
Ripple 3.0 mV maximum peak-to-peak
DC Output Adjustment Range +/- 5% minimum
Overvoltage Protection OVP is optionally available
Remote Sensing Standard built-in open sense load protection.
Overload Protection 125 to 150% foldback current limit
Contact Technical Services at 1-800-377-4384 or [email protected] with any questions. Visit our website at www.solaheviduty.com
Contact Technical Services at 1-800-377-4384 or [email protected] with any questions. Visit our website at www.solaheviduty.com
*Note: Unit is shipped for 120V input from factory.
Mechanical Dimensions: Inches (mm)
15.98" (406). 375" (9.53)
16.85" (428)AC INPUT/DC OUTPUT
°MTG HOLES (16 PLACES). 394" (10) . 236”
(6.0)
. 39” (10)
4.92
"(125
)
2.52
"( 64)
3.46" (88)
4.13
”(105
)
2.52” (64) . 55" (14)
-S 41 235
-O
UT
+S
+O
UT
AC Input
OVP (OPTIONAL) 1.34" (34)
WEIGHT: 19 LBS.(8.55 KG)
Heat Sink
. 630 (16) Ma x.
R1 I.LIM
R20 V.ADJ
Application Note: User needs to provide earth ground to power supply with either solder to Tab or using washer and nut assembly. The SLS power supply is shipped from the factory with metal shorting straps connected between the + OUT and + S terminals and the (-) OUT and (-) S terminals. This strapping configuration allows the output of the SLS to be taken from either pair of terminals. This is the standard configuration. The remote sense feature is enabled by removing the shorting straps and connecting the individual OUT and S terminals to the appropriate points of the load. If an OVP circuit is used it should be connected to the + OUT and (-) OUT terminals. The OVP should never be connected to the + S, - S terminals without the use of the shorting straps. In all cases it is critical that the terminal screws be firmly tightened.
Case L Note: The SLS models DC output can be adjusted with R20 V. ADJ.
R1 I. LIM is factory set and should not be adjusted by users.
• Easy installation with strip terminal• Tight regulation: 0.05% Line; 0.05% Load• Full Output Ratings to +50oC• OVP Option Available• Foldback Current Limiting Overload Protection with
Automatic Recovery
• Multi-Tap AC Inputs• 100% Four-Hour Burn-in• Please see enclosed “Terms & Conditions and
Sales & Policies & Procedures”• UL Recognized• CSA Certified• CE Marked• CB Certified
Serie SL - Lineales de Salida Sencilla & Múltiple Manual de la Instrucción
Modelo: SLS-24-120T
Características
Entrada AC Conexiones (See Caja L)
Especificaciones
Para el uso en: Conecte Aplique AC a: El fusible primario
100 VAC 1-3, 2-4 1 & 5 6.0 A / 125V
120 VAC* 1-3, 2-4 1 & 4 6.0 A / 125V
220 VAC 2-3 1 & 5 3.0 A / 250V
230 VAC 2-3 1 & 4 3.0 A / 250V
240 VAC 2-3 1 & 4 3.0 A / 250V
P/N A272-027 Rev. 4 (August 16, 2007)
Contacte los Servicios Técnicos en 1-847-268-6000 o [email protected] con cualquiera preguntan. Visite nuestro sitio web en www.solaheviduty. com
Contacte los Servicios Técnicos en 1-847-268-6000 o [email protected] con cualquiera preguntan. Visite nuestro sitio web en www.solaheviduty. com
* La nota: La unidad se envia para la entrada 120V de la fábrica.
Caja L La nota: La salida DC de los modelos SLS puede ser ajustada con el R20 V. ADJ
R1 I. LIM ha sido fijada en la fabrica y no se debe ajustar por los usuarios.
La Nota de la aplicación: Las necesidades de Usuario a proporcionar la tierra el suelo para accionar el suministro con o soldadura qa la Etiqueta o utilizar arandela y asamblea de nuez. La planta SLS se envía de fábrica con bandas metálicas de cortocircuito conectadas entre los terminales + OUT (salida) y + S y los terminales (-) OUT y (-) S. Esta configuración de bandas permite la salida desde la SLS desde cualquier par de terminales, y es la configuración estándar. La función de sensor remoto se activa al retirar las bandas de cortocircuito y conectar los terminales individuales de salida (OUT) y S con los puntos pertinentes de la carga. Si se utiliza un circuito OVP, deberá conectarse con los terminales + OUT y (-) OUT. El circuito OVP no debe conectarse nunca con los terminales + S, - S sin las bandas de cortocircuito. En todos los casos es esencial ajustar los tornillos del terminal firmemente.
Dimensiones (pulg/mm)
Voltaje/Las Calificaciones ActualesNúmero de Catálogo Salida 1
SLS-24-120T 24 V / 12 A
Rango de Operación de Temperatura 0 to +50oC (Ajuste al 40% a +70oC)
Coeficiente de Temperatura (Típico) +/- 0.01% / oC
Estabilidad Dentro de +/- 0.05% (24 horas después del calentamiento)
Vibración De acuerdo con MIL-STD-810C, Método 514
Golpes De acuerdo con MIL-STD-810C, Método 516
EMI/RFILas fuentes de alimentación lineales tienen inherentemente bajos niveles de ruido conducido y radiado. Para la mayoría de las aplicaciones en sistemas estas cumplen con los requerimientos de FCC Clase B y VDE 0871 para Clase B.
Enfriamiento De aire forzado. 20 CFM requeridos para el grado completo reducen la capacidad normal del 30% para refrescarse de la convección.
EntradaVoltaje de Entrada 100/120/220/230/240 VAC selectable +/- 10% except 230 VAC is +15%, -6%
Frecuencia de Entrada 47-63 Hz (Típico es 60 Hz. La producción de Derate 10% en 50 Hz)
Tiempo de Respuesta a Transientes 100 µsec para 50% en 100% la carga cambia.
Funda los RequisitosLas unidades no se funden internamente. Para la operación segura, el usuario debe proporcionar fusible de entrada de línea como por valores se rindió tabla.
SalidaRegulación de Línea 0.05% para un cambio del 10%
Regulación de la carga 0.05% para un cambio del 50%
Rizo 3.0 mV máximo Pico-a-Pico
Rango de Ajuste de CD de Salida +/- 5% Mínimo
Protección de Sobrevoltaje Opción de OVP Disponible
Protección contra Sobrecarga 125 to 150% foldback automático de limitación de corriente
Sensores Remotos La protección abierta, incorporada y uniforme de la carga del sentido.
• Terminales de conexión fáciles de instalar. • De salida ajustable de 12V a 15V• Tight regulation: 0.05% Line; 0.05% Load• Las calificaciones de salida a +50oC• Opción de OVP Disponible• Foldback Current Limiting Protección contra
Sobrecarga con Automático Recupera
• Multi-Tap AC Las Entradas• 100% Cuatro Hora Burn-in• Sírvase consultar “Términos y Condiciones, y
Políticas y Procedimientos de Ventas” • Reconocido por UL • Certificado CSA • Aprovado en CE • Certificado CB
15.98" (406). 375" (9.53)
16.85" (428)AC INPUT/DC OUTPUT
°MTG HOLES (16 PLACES). 394" (10) . 236”
(6.0)
. 39” (10)
4.92
"(125
)
2.52
"( 64)
3.46" (88)
4.13
”(105
)
2.52” (64) . 55" (14)
-S 41 235
-O
UT
+S
+O
UT
AC Input
OVP (OPTIONAL) 1.34" (34)
WEIGHT: 19 LBS.(8.55 KG)
Heat Sink
. 630 (16) Ma x.
R1 I.LIM
R20 V.ADJ
Output AdjustmentStep 1: Check the input AC connections
Step 2: Connect the AC input according to table below.
Step 3: Use VR6 to adjust +V. Adj. to +15V or +12V.
Step 4: Use VR4 to adjust -V. Adj. to -15V or -12V.
Linear Open Frame DC Power SuppliesSilver Line Instruction Manual
Model: SLT12-20404-12T
Features
General Specifications
Voltage/Current RatingsModel Number Output 1 Output 2 Output 3
SLT12-20404-12T 5V@2A [email protected] or [email protected] [email protected] or [email protected]
*Outputs are tied common
Operating Temperature Range 0 to +50oC (Derate to 40% at +70oC)
Temperature Coefficient (Typical) +/- 0.01% / oC
Stability Within +/- 0.05% (For 24 hours after warm-up)
Vibration Per MIL-STD-810C, Method 514
Shock Per MIL-STD-810C, Method 516
EMI/RFI Linear power supplies have inherently low conducted and radiated noise levels. For most system applications, these power supplies will meet the requirements of FCC Class “B” and VDE 0871 for Class “B” equipment without additional noise filtering.
Cooling Forced air. 20 CFM required for full rating Derate 30% for convection cooling.
Input SpecificationsMulti Input (all units) 100/120/220/230/240 VAC selectable +/- 10% except 230 VAC is +15%, -6%
Frequency Range 47-63 Hz (Typical is 60 Hz. Derate output 10% at 50 Hz)
Transient Response Time 50 µsec at 50% load change
Fuse Requirements Units are not fused internally. For safe operation, user must provide input line fuse as per values given in table.
Output SpecificationsLine Regulation 0.05% for +/- 10% change
Load Regulation 0.05% for 50% change
Ripple 3.0 mV maximum peak-to-peak
DC Output Adjustment Range +/- 5% minimum
Overvoltage Protection All 5 volt outputs include built-in OVP as standard (setting is 6.2V +/-0.4V). OVP is optionally available on other outputs.
Overload Protection 125 to 150% foldback current limit
Contact Technical Services at 1-800-377-4384 or [email protected] with any questions. Visit our website at www.solaheviduty.com
Contact Technical Services at 1-800-377-4384 or [email protected] with any questions. Visit our website at www.solaheviduty.com
Input AC Connections
Mechanical Dimensions: inches (mm)
For use at: Connect Apply AC to: Primary Fuse100 VAC 1-3, 2-4 1 & 5 0.63A/125V
120 VAC* 1-3, 2-4 1 & 4 0.63A/125V
220 VAC 2-3 1 & 5 0.315A/250V
230 VAC 2-3 1 & 4 0.315A/250V
240 VAC 2-3 1 & 4 0.315A/250V
Case H2
*Note: Unit is shipped for 120V input from factory.
Application Note: User needs to provide earth ground to power supply with either solder to Tab or using washer and nut assembly. The SLT power supply is shipped from the factory with metal shorting straps connected between the + OUT and + S terminals and the (-) OUT and (-) S terminals. This strapping configuration allows the output of the SLS to be taken from either pair of terminals. This is the standard configuration. The remote sense feature is enabled by removing the shorting straps and connecting the individual OUT and S terminals to the appropriate points of the load. If an OVP circuit is used it should be connected to the + OUT and (-) OUT terminals. The OVP should never be connected to the + S, - S terminals without the use of the shorting straps. In all cases it is critical that the terminal screws be firmly tightened.
Note: I. LIM is factory set and should not be adjusted by users.
• Easy installation with strip terminal
• Output adjustable from 12V to 15V
• Tight regulation: 0.05% Line; 0.05% Load
• Full Output Ratings to +50oC
• Built in OVP on 5 Volt Outputs
• OVP Option for 12V and 15V
• Foldback Current Limiting Overload Protection with Automatic Recovery
• Multi-Tap AC Inputs
• 100% Four-Hour Burn-in
• Please see enclosed “Terms & Conditions and Sales & Policies & Procedures”
• UL Recognized
• CSA Certified
El Ajuste de SalidaDé un paso 1: Verifica las conexiones de entrada de C.A.
Dé un paso 2: Conecte a la entrada de C.A. según posponer abajo.
Dé un paso 3: Utilice VR6 para ajustar +V. Adj. to +15V or +12V
Dé un paso 4: Utilice VR4 para ajustar -V. Adj. to -15V or -12V
Serie SL - Lineales de Salida Sencilla & Múltiple Manual de la Instrucción
Modelo: SLT12-20404-12T
Características
Especificaciones
P/N A272-051 Rev. 4 (August 17, 2007)
Contacte los Servicios Técnicos en 1-847-268-6000 o [email protected] con cualquiera preguntan. Visite nuestro sitio web en www.solaheviduty. com
Contacte los Servicios Técnicos en 1-847-268-6000 o [email protected] con cualquiera preguntan. Visite nuestro sitio web en www.solaheviduty. com
Voltaje/Las Calificaciones ActualesNúmero de Catálogo Salida 1 Salida 2 Salida 3
SLT12-20404-12T 5V@2A [email protected] or [email protected] [email protected] or [email protected]
*Outputs are tied common
Rango de Operación de Temperatura 0 to +50oC (Ajuste al 40% a +70oC)
Coeficiente de Temperatura (Típico) +/- 0.01% / oC
Estabilidad Después del calentamiento inicial, ±.5%
Vibración De acuerdo con MIL-STD-810C, Método 514
Golpes De acuerdo con MIL-STD-810C, Método 516
EMI/RFI Las fuentes de alimentación lineales tienen inherentemente bajos niveles de ruido conducido y radiado. Para la mayoría de las aplicaciones en sistemas estas cumplen con los requerimientos de FCC Clase B y VDE 0871 para Clase B.
Enfriamiento De aire forzado. 20 CFM requeridos para el grado completo reducen la capacidad normal del 30% para refrescarse de la convección.
EntradaVoltaje de Entrada 100/120/220/230/240 VAC selectable +/- 10% except 230 VAC is +15%, -6%
Frecuencia de Entrada 47-63 Hz (Típico es 60 Hz. La producción de Derate 10% en 50 Hz)
Tiempo de Respuesta a Transientes 50 µsec at 50% load change
Funda los Requisitos Las unidades no se funden internamente. Para la operación segura, el usuario debe proporcionar fusible de entrada de línea como por valores se rindió tabla.
SalidaRegulación de Línea 0.05% para un cambio del 10%
Regulación de la carga 0.05% para un cambio del 50%
Rizo 3.0 mV máximo Pico-a-Pico
Rango de Ajuste de CD de Salida +/- 5% Mínimo
Protección de Sobrevoltaje Todas las salidas de 5-Volt incluyen OVP integrada como un estándar (el ajuste es 6.2 V ±0.4 V) OVP está disponible opcionalmente en otros tipos
Protección contra Sobrecarga 125 to 150% foldback automático de limitación de corriente
Input AC Conexiones
Para el uso en: Conecte Aplique AC a: El fusible primario
100 VAC 1-3, 2-4 1 & 5 0.63A/125V
120 VAC* 1-3, 2-4 1 & 4 0.63A/125V
220 VAC 2-3 1 & 5 0.315A/250V
230 VAC 2-3 1 & 4 0.315A/250V
240 VAC 2-3 1 & 4 0.315A/250V
* La nota: La unidad se envía para la entrada 120V de la fábrica.
Caja H2
La Nota de la aplicación: Las necesidades de Usuario a proporcionar la tierra el suelo para accionar el suministro con o soldadura qa la Etiqueta o utilizar arandela y asamblea de nuez. La planta SLT se envía de fábrica con bandas metálicas de cortocircuito conectadas entre los terminales + OUT (salida) y + S y los terminales (-) OUT y (-) S. Esta configuración de bandas permite la salida desde la SLS desde cualquier par de terminales, y es la configuración estándar. La función de sensor remoto se activa al retirar las bandas de cortocircuito y conectar los terminales individuales de salida (OUT) y S con los puntos pertinentes de la carga. Si se utiliza un circuito OVP, deberá conectarse con los terminales + OUT y (-) OUT. El circuito OVP no debe conectarse nunca con los terminales + S, - S sin las bandas de cortocircuito. En todos los casos es esencial ajustar los tornillos del terminal firmemente.
Dimensiones (pulg/mm)
La nota: I. LIM ha sido fijada en la fabrica y no se debe ajustar por los usuarios.
• Terminales de conexión fáciles de instalar.
• De salida ajustable de 12V a 15V
• Tight regulation: 0.05% Line; 0.05% Load
• Las calificaciones de salida a +50oC
• OVP integrada en modelos de 5 V y opcional en los modelos de 12 y 15 V.
• Foldback Current Limiting Protección contra Sobrecarga con Automático Recupera
• Multi-Tap AC Las Entradas
• 100% Cuatro Hora Burn-in
• Sírvase consultar “Términos y Condiciones, y Políticas y Procedimientos de Ventas”
• UL Reconocido
• CSA Certificado
Output AdjustmentStep 1: Check the input AC connections
Step 2: Connect the AC input according to table below.
Step 3: SLT12-31010-12T can be set to +15V or +12V by adjusting VR6.
Step 4: SLT12-31010-12T can be set to -15V or -12V by adjusting VR4.
Note: I. LIM is factory set on all models and should not be adjusted by users.
Linear Open Frame DC Power SuppliesSilver Line Instruction Manual
Model: SLT12-31010-12T
Features
General Specifications
Voltage/Current RatingsModel Number Output 1 Output 2 Output 3
SLT12-31010-12T 5V@3A +12V@1A or [email protected] -12V@1A or [email protected]
*Outputs are tied common
Operating Temperature Range 0 to +50oC (Derate to 40% at +70oC)
Temperature Coefficient (Typical) +/- 0.01% / oC
Stability Within +/- 0.05% (For 24 hours after warm-up)
Vibration Per MIL-STD-810C, Method 514
Shock Per MIL-STD-810C, Method 516
EMI/RFI Linear power supplies have inherently low conducted and radiated noise levels. For most system applications, these power supplies will meet the requirements of FCC Class “B” and VDE 0871 for Class “B” equipment without additional noise filtering.
Cooling Forced air. 20 CFM required for full rating Derate 30% for convection cooling.
Input SpecificationsMulti Input (all units) 100/120/220/230/240 VAC selectable +/- 10% except 230 VAC is +15%, -6%
Frequency Range 47-63 Hz (Typical is 60 Hz. Derate output 10% at 50 Hz)
Transient Response Time 50 µsec at 50% load change
Fuse Requirements Units are not fused internally. For safe operation, user must provide input line fuse as per values given in table.
Output SpecificationsLine Regulation 0.05% for +/- 10% change
Load Regulation 0.05% for 50% change
Ripple 3.0 mV maximum peak-to-peak
DC Output Adjustment Range +/- 5% minimum
Overvoltage Protection All 5 volt outputs include built-in OVP as standard (setting is 6.2V +/-0.4V). OVP is optionally available on other outputs.
Overload Protection 125 to 150% foldback current limit
Contact Technical Services at 1-800-377-4384 or [email protected] with any questions. Visit our website at www.solaheviduty.com
Contact Technical Services at 1-800-377-4384 or [email protected] with any questions. Visit our website at www.solaheviduty.com
Input AC Connections
Mechanical Dimensions: inches (mm)
For use at: Connect Apply AC to: Primary Fuse100 VAC 1-3, 2-4 1 & 5 1.6A / 125V
120 VAC* 1-3, 2-4 1 & 4 1.6A / 125V
220 VAC 2-3 1 & 5 0.8A / 250V
230 VAC 2-3 1 & 4 0.8A / 250V
240 VAC 2-3 1 & 4 0.8A / 250V
Case F
*Note: Unit is shipped for 120V input from factory.
Application Note: User needs to provide earth ground to power supply with either solder to Tab or using washer and nut assembly. The SLT power supply is shipped from the factory with metal shorting straps connected between the + OUT and + S terminals and the (-) OUT and (-) S terminals. This strapping configuration allows the output of the SLS to be taken from either pair of terminals. This is the standard configuration. The remote sense feature is enabled by removing the shorting straps and connecting the individual OUT and S terminals to the appropriate points of the load. If an OVP circuit is used it should be connected to the + OUT and (-) OUT terminals. The OVP should never be connected to the + S, - S terminals without the use of the shorting straps. In all cases it is critical that the terminal screws be firmly tightened.
• Easy installation with strip terminal
• Output adjustable from 12V to 15V
• Tight regulation: 0.05% Line; 0.05% Load
• Full Output Ratings to +50oC
• Built in OVP on 5 Volt Outputs
• OVP Option for 12V and 15V
• Foldback Current Limiting Overload Protection with Automatic Recovery
• Multi-Tap AC Inputs
• 100% Four-Hour Burn-in
• Please see enclosed “Terms & Conditions and Sales & Policies & Procedures”
• UL Recognized
• CSA Certified
El Ajuste de SalidaDé un paso 1: Verifica las conexiones de entrada de C.A.
Dé un paso 2: Conecte a la entrada de C.A. según posponer abajo.
Dé un paso 3: SLT12-31010-12T se puede establecer en el rango +12V to +15V ajustando VR6.
Dé un paso 4: SLT12-31010-12T se puede establecer en el rango -12V to -15V ajustando VR4.
La nota: I. LIM ha sido fijada en la fabrica y no se debe ajustar por los usuarios.
Serie SL - Lineales de Salida Sencilla & Múltiple Manual de la Instrucción
Modelo: SLT12-31010-12T
Características
Especificaciones
P/N A272-052 Rev. 2 (August 17, 2007)
Contacte los Servicios Técnicos en 1-847-268-6000 o [email protected] con cualquiera preguntan. Visite nuestro sitio web en www.solaheviduty. com
Contacte los Servicios Técnicos en 1-847-268-6000 o [email protected] con cualquiera preguntan. Visite nuestro sitio web en www.solaheviduty. com
Voltaje/Las Calificaciones ActualesNúmero de Catálogo Salida 1 Salida 2 Salida 3
SLT12-31010-12T 5V@3A +12V@1A or [email protected] -12V@1A or [email protected]
*Outputs are tied common
Rango de Operación de Temperatura 0 to +50oC (Ajuste al 40% a +70oC)
Coeficiente de Temperatura (Típico) +/- 0.01% / oC
Estabilidad Después del calentamiento inicial, ±.5%
Vibración De acuerdo con MIL-STD-810C, Método 514
Golpes De acuerdo con MIL-STD-810C, Método 516
EMI/RFI Las fuentes de alimentación lineales tienen inherentemente bajos niveles de ruido conducido y radiado. Para la mayoría de las aplicaciones en sistemas estas cumplen con los requerimientos de FCC Clase B y VDE 0871 para Clase B.
Enfriamiento De aire forzado. 20 CFM requeridos para el grado completo reducen la capacidad normal del 30% para refrescarse de la convección.
EntradaVoltaje de Entrada 100/120/220/230/240 VAC selectable +/- 10% except 230 VAC is +15%, -6%
Frecuencia de Entrada 47-63 Hz (Típico es 60 Hz. La producción de Derate 10% en 50 Hz)
Tiempo de Respuesta a Transientes 50 µsec at 50% load change
Funda los Requisitos Las unidades no se funden internamente. Para la operación segura, el usuario debe proporcionar fusible de entrada de línea como por valores se rindió tabla.
SalidaRegulación de Línea 0.05% para un cambio del 10%
Regulación de la carga 0.05% para un cambio del 50%
Rizo 3.0 mV máximo Pico-a-Pico
Rango de Ajuste de CD de Salida +/- 5% Mínimo
Protección de Sobrevoltaje Todas las salidas de 5-Volt incluyen OVP integrada como un estándar (el ajuste es 6.2 V ±0.4 V) OVP está disponible opcionalmente en otros tipos
Protección contra Sobrecarga 125 to 150% foldback automático de limitación de corriente
Input AC Conexiones
Para el uso en: Conecte Aplique AC a: El fusible primario
100 VAC 1-3, 2-4 1 & 5 1.6A / 125V
120 VAC* 1-3, 2-4 1 & 4 1.6A / 125V
220 VAC 2-3 1 & 5 0.8A / 250V
230 VAC 2-3 1 & 4 0.8A / 250V
240 VAC 2-3 1 & 4 0.8A / 250V
Caja F
* La nota: La unidad se envía para la entrada 120V de la fábrica.
La Nota de la aplicación: Las necesidades de Usuario a proporcionar la tierra el suelo para accionar el suministro con o soldadura qa la Etiqueta o utilizar arandela y asamblea de nuez. La planta SLT se envía de fábrica con bandas metálicas de cortocircuito conectadas entre los terminales + OUT (salida) y + S y los terminales (-) OUT y (-) S. Esta configuración de bandas permite la salida desde la SLS desde cualquier par de terminales, y es la configuración estándar. La función de sensor remoto se activa al retirar las bandas de cortocircuito y conectar los terminales individuales de salida (OUT) y S con los puntos pertinentes de la carga. Si se utiliza un circuito OVP, deberá conectarse con los terminales + OUT y (-) OUT. El circuito OVP no debe conectarse nunca con los terminales + S, - S sin las bandas de cortocircuito. En todos los casos es esencial ajustar los tornillos del terminal firmemente.
Dimensiones (pulg/mm)
• Terminales de conexión fáciles de instalar.
• De salida ajustable de 12V a 15V
• Tight regulation: 0.05% Line; 0.05% Load
• Las calificaciones de salida a +50oC
• OVP integrada en modelos de 5 V y opcional en los modelos de 12 y 15 V.
• Foldback Current Limiting Protección contra Sobrecarga con Automático Recupera
• Multi-Tap AC Las Entradas
• 100% Cuatro Hora Burn-in
• Sírvase consultar “Términos y Condiciones, y Políticas y Procedimientos de Ventas”
• UL Reconocido
• CSA Certificado
Output AdjustmentStep 1: Check the input AC connectionsStep 2: Connect the AC input according to table below.
Step 3: Use VR6 to adjust to +V.Adj. +15V or +12V.
Step 4: Use VR4 to adjust to -V.Adj. -15V or -12V..
Linear Open Frame DC Power SuppliesSilver Line Instruction Manual
Model: SLT12-61818-12T
Features
General Specifications
Voltage/Current RatingsModel Number Output 1 Output 2 Output 3
SLT12-61818-12T 5V@6A [email protected] or [email protected] [email protected] or [email protected]
*Outputs are tied common
Operating Temperature Range 0 to +50oC (Derate to 40% at +70oC)
Temperature Coefficient (Typical) +/- 0.01% / oC
Stability Within +/- 0.05% (For 24 hours after warm-up)
Vibration Per MIL-STD-810C, Method 514
Shock Per MIL-STD-810C, Method 516
EMI/RFI Linear power supplies have inherently low conducted and radiated noise levels. For most system applications, these power supplies will meet the requirements of FCC Class “B” and VDE 0871 for Class “B” equipment without additional noise filtering.
Cooling Forced air. 20 CFM required for full rating Derate 30% for convection cooling.
Input SpecificationsMulti Input (all units) 100/120/220/230/240 VAC selectable +/- 10% except 230 VAC is +15%, -6%
Frequency Range 47-63 Hz (Typical is 60 Hz. Derate output 10% at 50 Hz)
Transient Response Time 50 µsec at 50% load changes for outputs rated up to 6A
100 µsec at 50% load changes for outputs rated 6A and over.
Fuse Requirements Units are not fused internally. For safe operation, user must provide input line fuse as per values given in table.
Output SpecificationsLine Regulation 0.05% for +/- 10% change
Load Regulation 0.05% for 50% change
Ripple 3.0 mV maximum peak-to-peak
DC Output Adjustment Range +/- 5% minimum
Overvoltage Protection All 5 volt outputs include built-in OVP as standard (setting is 6.2V +/-0.4V). OVP is optionally available on other outputs.
Overload Protection 125 to 150% foldback current limit
Contact Technical Services at 1-800-377-4384 or [email protected] with any questions. Visit our website at www.solaheviduty.com
Contact Technical Services at 1-800-377-4384 or [email protected] with any questions. Visit our website at www.solaheviduty.com
Input AC Connections
For use at: Connect Apply AC to: Primary FuseSLT12-61818-12T (Case G2)
100 VAC 1-3, 2-4 1 & 5 2A / 125V
120 VAC* 1-3, 2-4 1 & 4 2A / 125V
220 VAC 2-3 1 & 5 1A / 250V
230 VAC 2-3 1 & 4 1A / 250V
240 VAC 2-3 1 & 4 1A / 250V
*Note: Unit is shipped for 120V input from factory.
Application Note: User needs to provide earth ground to power supply with either solder to Tab or using washer and nut assembly. The SLT power supply is shipped from the factory with metal shorting straps connected between the + OUT and + S terminals and the (-) OUT and (-) S terminals. This strapping configuration allows the output of the SLS to be taken from either pair of terminals. This is the standard configuration. The remote sense feature is enabled by removing the shorting straps and connecting the individual OUT and S terminals to the appropriate points of the load. If an OVP circuit is used it should be connected to the + OUT and (-) OUT terminals. The OVP should never be connected to the + S, - S terminals without the use of the shorting straps. In all cases it is critical that the terminal screws be firmly tightened.
Mechanical Dimensions: inches (mm)
Case G2
Note: I. LIM is factory set on all models and should not be adjusted by users.
• Easy installation with strip terminal• Output adjustable from 12V to 15V• Tight regulation: 0.05% Line; 0.05% Load• Full Output Ratings to +50oC• Built in OVP on 5 Volt Outputs• OVP Option for 12V, 15V and 24V• Foldback Current Limiting Overload Protection with
Automatic Recovery
• Multi-Tap AC Inputs• 100% Four-Hour Burn-in
• Please see enclosed “Terms & Conditions and Sales & Policies & Procedures”
• UL Recognized
• CSA Certified
El Ajuste de SalidaDé un paso 1: Verifica las conexiones de entrada de C.A.Dé un paso 2: Conecte a la entrada de C.A. según posponer abajo. Dé un paso 3: Utilice VR6 para ajustar +15V or +12V.Dé un paso 4: Utilice VR4 para ajustar -15 or -12.
P/N A272-053 Rev. 3 (August 17 , 2007)
Contacte los Servicios Técnicos en 1-847-268-6000 o [email protected] con cualquiera preguntan. Visite nuestro sitio web en www.solaheviduty. com
Input AC Conexiones
Para el uso en: Conecte Aplique AC a: El fusible primario
SLT12-61818-12T (Case G2)
100 VAC 1-3, 2-4 1 & 5 2A / 125V
120 VAC* 1-3, 2-4 1 & 4 2A / 125V
220 VAC 2-3 1 & 5 1A / 250V
230 VAC 2-3 1 & 4 1A / 250V
240 VAC 2-3 1 & 4 1A / 250V
* La nota: La unidad se envía para la entrada 120V de la fábrica.
Serie SL - Lineales de Salida Sencilla & Múltiple Múltiple Manual de la Instrucción
Modelo: SLT12-61818-12T
Características
Especificaciones
Contacte los Servicios Técnicos en 1-847-268-6000 o [email protected] con cualquiera preguntan. Visite nuestro sitio web en www.solaheviduty. com
Voltaje/Las Calificaciones ActualesNúmero de Catálogo Salida 1 Salida 2 Salida 3
SLT12-61818-12T 5V@6A [email protected] or [email protected] [email protected] or [email protected]
*Outputs are tied common
Rango de Operación de Temperatura 0 to +50oC (Ajuste al 40% a +70oC)
Coeficiente de Temperatura (Típico) +/- 0.01% / oC
Estabilidad Después del calentamiento inicial, ±.5%
Vibración De acuerdo con MIL-STD-810C, Método 514
Golpes De acuerdo con MIL-STD-810C, Método 516
EMI/RFI Las fuentes de alimentación lineales tienen inherentemente bajos niveles de ruido conducido y radiado. Para la mayoría de las aplicaciones en sistemas estas cumplen con los requerimientos de FCC Clase B y VDE 0871 para Clase B.
Enfriamiento De aire forzado. 20 CFM requeridos para el grado completo reducen la capacidad normal del 30% para refrescarse de la convección.
EntradaVoltaje de Entrada 100/120/220/230/240 VAC selectable +/- 10% except 230 VAC is +15%, -6%
Frecuencia de Entrada 47-63 Hz (Típico es 60 Hz. La producción de Derate 10% en 50 Hz)
Tiempo de Respuesta a Transientes 50 µsec en 50% la carga cambia para producciones valoradas hasta 6A. 100 µsec en 50% la carga cambia para producciones valoradas 6A y sobre.
Funda los Requisitos Las unidades no se funden internamente. Para la operación segura, el usuario debe proporcionar fusible de entrada de línea como por valores se rindió tabla.
SalidaRegulación de Línea 0.05% para un cambio del 10%
Regulación de la carga 0.05% para un cambio del 50%
Rizo 3.0 mV máximo Pico-a-Pico
Rango de Ajuste de CD de Salida +/- 5% Mínimo
Protección de Sobrevoltaje Todas las salidas de 5-Volt incluyen OVP integrada como un estándar (el ajuste es 6.2 V ±0.4 V) OVP está disponible opcionalmente en otros tipos
Protección contra Sobrecarga 125 to 150% foldback automático de limitación de corriente
Caja G2
Dimensiones (pulg/mm)
La Nota de la aplicación: Las necesidades de Usuario a proporcionar la tierra el suelo para accionar el suministro con o soldadura qa la Etiqueta o utilizar arandela y asamblea de nuez. La planta SLT se envía de fábrica con bandas metálicas de cortocircuito conectadas entre los terminales + OUT (salida) y + S y los terminales (-) OUT y (-) S. Esta configuración de bandas permite la salida desde la SLS desde cualquier par de terminales, y es la configuración estándar. La función de sensor remoto se activa al retirar las bandas de cortocircuito y conectar los terminales individuales de salida (OUT) y S con los puntos pertinentes de la carga. Si se utiliza un circuito OVP, deberá conectarse con los terminales + OUT y (-) OUT. El circuito OVP no debe conectarse nunca con los terminales + S, - S sin las bandas de cortocircuito. En todos los casos es esencial ajustar los tornillos del terminal firmemente.
La nota: I. LIM ha sido fijada en la fabrica y no se debe ajustar por los usuarios.
• Terminales de conexión fáciles de instalar.
• De salida ajustable de 12V a 15V
• Tight regulation: 0.05% Line; 0.05% Load
• Las calificaciones de salida a +50oC
• OVP integrada en modelos de 5 V y opcional en los modelos de 12, 15 y 24 V.
• Foldback Current Limiting Protección contra Sobrecarga con Automático Recupera
• Multi-Tap AC Las Entradas
• 100% Cuatro Hora Burn-in
• Sírvase consultar “Términos y Condiciones, y Políticas y Procedimientos de Ventas”
• UL Reconocido
• CSA Certificado