Date post: | 29-Mar-2015 |
Category: |
Documents |
Upload: | ayanna-hume |
View: | 227 times |
Download: | 1 times |
Linear Power Supply
Outline
• Linear Power Supply– Poor man’s cell phone charger– Small signal resistance
• Adjustable power supply• Rectifier Circuit– Half-wave rectifier circuit– Full-wave rectifier circuit– Full-wave rectifier circuit as a Frequency mixer
• Filter Circuit• Rectifier Circuit
Outline
• Large-Signal and Small-Signal Operation
• Application of Diodes (Up to 3.5.1)
How does a small increase in Vad affect Vout?
Drop in Output Voltage
(Slope)
Small Signal Resistance
Small Signal Resistance: ID/VT
I-V Characteristic of a 1n4001 Diode
Export I-V Data to a Table
Export Table
Small Signal Resistance
VF (V) IF (Computed)
0.748 67.57 mA
0.740 57.89 mA
Dynamic Resistance from the measurement:(0.748-0.740)/(67.57 mA-57.89 mA)= 0.826 Ohms
Using Small Signal Model in a Small Signal Calculation
Small Signal Model of Adaptor
Change in Vad
How should a load be modeled?
A laptop consumes an average power of 25 W with a supply voltage of 3.3 V. Determine the average current drawn from the batteries or the adaptor.
P=VII= 7.56 A
If the laptop is modeled by a resistor, then RL is 0.436 Ohms.
You Can’t Power a Laptop with a Circuit Like this!
How should a Cellphone load be modeled?
A cellphone consumes an average power of 100 mW with a supply voltage of 2.4 V. Determine the average current drawn from the batteries or the adaptor.
P=VII= 41.6 mA
If the cellphone is modeled by a resistor, then RL is 79 Ohms.
Use a 79 Ohm Resistor to Model a Cell Phone Load
Dual-Output Adjustable Linear Regulated Power
Supply
Block Diagram
Simple Description
• Transformer: “Downconvert” the AC line voltage to a smaller peak voltage Vm, usually about 2-3 Volts larger than the ultimately desired DC output.
• Diode Rectifier Circuit: produce a waveform with large DC component.
• Filter: smooth out the rectified sinusoid. • Regulator: eliminate residual ripple
c03f27
Half-Wave Rectifier
Assume constant voltage model for diodes
Voltage offset
Diode is off for Vin < VD,on
On for Vin less than –VD,on
Ideal Diode Model
An AC-DC Converter Circuit
An AC-DC Converter Circuit
Constant Voltage Diode Model
Issue: It remains to be seen whether it can provide a current to a load
How should a load be modeled?
A laptop consumes an average power of 25 W with a supply voltage of 3.3 V. Determine the average current drawn from the batteries or the adaptor.
P=VII= 7.56 A
If the laptop is modeled by a resistor, then RL is 0.436 Ohms.
Rectifier Driving a Resistive Load
Vin begins to fall after t1 because RL providesa discharge path for C1.C1 must be sufficient large so that the currentdrawn by RL does not reduce Vout significantly.
The diode is turned on again
ripples
C1 is called smoothing capacitor
Tin
Magnitude of the Ripple
(Vp-VD,on)/RL is the currentdischarged through RL
(basic form of this equation:Q=CV)
The Maximum Forward Bias Current
Maximum Forward Current Occurs at the point when the diode turns on (t1)1.C1dVout/dt is maximum2.The current supplied to RL is (Vp-VD,on)/RL
Screen Shots
Smoothed Capacitor