www.OpticArts.com tel: 213.250.6069
LineLED X18WET-T Wet Location Linear LED strip - 24 VDC
page 1 of 7REV1.0 November 14, 2019 12:54 PM
EnvironmentWet Location
Operating Voltage24 VDC
Lumen Maintenance50,000 Hours
Warranty3 Years
Technical information
Ordering code
LLX18WET-T is a high performance flexible LED fixture suitable for use in coves, under cabinets, in shelves, and virtually anywhere a linear fixture is required.
Electrical
Physical Performance
Lumen Output
Input Voltage 24VDC
Power Consumption 4.4 Watts per foot (18 LEDs per foot)
Wire Size 18AWG, 2 wire
Certification ETL - Conforms to UL Std. 2108; Certified to CSA Std. C22.2 No. 9.0.Class 2
Field Cuttable Every 3.89” (99.00mm)
Operating Temperature -40°F (-40° C) to +158°F (+70°C)
Environment Wet Location
Maximum Run Length 21.00’ (6400.80mm)
Dimensions 0.50” (12.7mm) x 0.25” (6.35mm)End Caps - 0.57” (14.29mm) x 0.38” (9.53mm)
2400K 320.54 lm/ft 72.85 lm/Watt
2700K 367.44 lm/ft 83.51 lm/Watt
3000K 371.09 lm/ft 84.34 lm/Watt
3500K 398.72 lm/ft 90.62 lm/Watt
4100K 392.39 lm/ft 89.18 lm/Watt
6000K 413.68 lm/ft 94.02 lm/WattNote: Stated lumen values have a tolerance of +/- 10%.
CRI 90+
Lumen Maintenance 50,000 Hours
Binning Tolerance +/- 100K
Warranty 3 Years
MODEL
LLX18WET-TLENGTHCOLOR SECTION START SECTION END
View specs above for increment options and maximum run limits.
F = Female connector M = Male connector SL = Soldered lead wires (72”) NC = No connector
F = Female connector M = Male connector SL = Soldered lead wires (72”) NC = No connector
24K F F
24K = 2400K27K = 2700K30K = 3000K35K = 3500K41K = 4100K60K = 6000K
R = RedG = GreenB = BlueA = Amber
www.OpticArts.com tel: 213.250.6069
LineLED X18WET-T Wet Location Linear LED strip - 24 VDC
page 2 of 7REV1.0 November 14, 2019 12:54 PM
Dimensions
LLX18WET-T
Dimensions
Width 0.50” (12.70mm)
Height 0.20” (5.15mm)
Cuttable Segment Length 0.57” (14.29mm)
Pitch Length 0.38” (9.53mm)
Max Run Length 21.00’ (6096.00mm)
Optic Arts® cuts all LLX18WET-T to length per customer specifications. Each length of LLX18WET-T is fitted with a 6’(1.8M) wire lead (custom lengths available upon request) and packaged on a reel in an anti-static bag. Bags are labeled with fixture type, length and location (if applicable). Each piece of channel is labeled with fixture type, length and location (if applicable), and is bundled by fixture type.
• Due to the nature of the LLX18WET-T product, specific lengths may not fall exactly on a cutting point. In this case, Optic Arts® will always cut to the smaller dimension unless otherwise specified.• Some on-site assembly required. See installation guides for details.
0.57
”
0.20”0.38
”
0.50”
*Encased in silicon
Specified Length~0.23” ~0.13”
www.OpticArts.com tel: 213.250.6069
LineLED X18WET-T Wet Location Linear LED strip - 24 VDC
page 3 of 7REV1.0 November 14, 2019 12:54 PM
Lens options / light transmission percentage per lens
Rounded SquareFrostedQClear
Frosted
HalfFrosted
MediumBeam FrostedM
Graze
Raised
G
R Clear 36°Beam Angle
C36
C
F
HF Satin IceSI SquareFrostedHF
Clear 10°Beam Angle
C10
0.30”(7.62mm)
KS Channel (KSC-XX)
0.69”(17.52mm)
F55%85%
HF72%
C36
83%
R51%
C
KXL Channel (KXLC-XX)
0.83”(21.08mm)
0.50”(12.70mm)
F46%74%
C HF61%
K45M Channel (K45MC-XX)0.85”
(21.59mm)
0.85”(21.59mm)
F42%71%
C HF58%
C10
67%
0.69”(17.52mm)
1.00” (25.40mm)
0.36”(9.14mm)
0.44”(11.17mm)
KRS Channel (KRSC-XX)
F55%85%
C HF72%
KL Channel (KLC-XX)
0.83”(21.08mm)
0.30”(7.62mm)
F55%85%
C HF68%
0.63”(16.00mm)
KRM Channel (KRMC-XX)1.00” (25.40mm)
0.69”(17.52mm)
0.55”(13.97mm)
F42%71%
C HF58%
KM Channel (KMC-XX)
0.49”(12.44mm)
0.69”(17.52mm)
F42%71%
C HF52%
C10
67%
R39%
CLA Channel (CLAC-XX)
0.84”(21.33mm)
0.77”(19.55mm)
Q63%
S62%
0.36”(9.14mm)
0.42”
0.83”(21.08mm)
1.21”(30.73mm)
KRL Channel (KRLC-XX)
F55%83%
C HF68%
ALS20 Channel (ALS20-XX)
0.97”(24.63mm)
0.78”(19.81mm)
F43%78%
C
KRXL Channel (KRXLC-XX)
0.55”(13.97mm)
0.63”(16.00mm)
1.21”(30.73mm)0.83”
(21.08mm)
F46%74%
C HF61%
www.OpticArts.com tel: 213.250.6069
LineLED X18WET-T Wet Location Linear LED strip - 24 VDC
page 4 of 7REV1.0 November 14, 2019 12:54 PM
Accessories
LC-O2P-MOutdoor Lead Connector (Male)
Ø 0.75”(19.00mm)
1.72”(43.75mm)
LC-O2P-FOutdoor Lead Connector (Female)
Ø 0.74”(18.75mm)
1.72”(43.75mm)
FLEX-ZIPStrain Relief Clip
0.37”(9.50mm)
0.19”(4.90mm)
0.77”(19.50mm)
FLEXMNT-SIL-EXT12Outdoor Mounting Clip
1.24” (28.00mm)
0.55” (14.00mm)
0.28” (7.00m
m)
0.24”(6.00m
m)
LO-18G-2C-W-726’ (1.8M) wire lead (not in-wall rated)
LP-18G-2C-W-726’ (1.8M) Plenum rated wire lead
www.OpticArts.com tel: 213.250.6069
LineLED X18WET-T Wet Location Linear LED strip - 24 VDC
page 5 of 7REV1.0 November 14, 2019 12:54 PM
REV0.0 09162019 page 3 of 6 www.luminii.com tel: 224-333-6033
LL91STP LineLED Linear LED strip - 24 VDC
24
24 LIN
48
3X96
Power supply
48 - 48 W96 - 96 W288 - 288 W (3x 96W)
96 - 96 WATT 3X96 - 3 X 96 WATT
24 - 24 VDC
24 - 24 VDC
Blank - 120 V240 - 240 V277 - 277 V
LIN - LinearLOG - Logarithmic
40POWER
POWER
POWER
PSV
PSD
PS010V
PSV - PSV Series dims down to 5%
PSD - PSD Series dims down to 0%
PS010V - 0-10V Power Supply dims down to 0%
MODEL
MODEL
MODEL
40 - 40 W60 - 60 W96 - 96 W
24OUTPUT
OUTPUT
OUTPUT
INPUT
DIMMING
24 - 24 VDC
U2DIM DDIMMING LOCATION
U2DIM - Dimming 0-10V D - Dry LocationIP65 - Wet Location
MODELS
A Length
B Width
C Depth
MODELS
A Length
B Width
C Depth
MODELS
A Length
B Width
C Depth
MODELS
A Length
B Width
C Depth
PSV Dry
9.2”
3.4”
1.9”
PSD 48
11.25”
3.42”
3.42”
PSV Wet
9.5”
4.12”
2.3”
PSD 96
11.25”
3.42”
3.27”
3X96
15.75”
6.60”
4.80”
Dual circuit
13.8”
4.0”
1.9”
Four circuit
13.8”
7.75”
1.9”
96 W
14.40”
5.20”
2.60”
Single circuit
13.9”
2.3”
1.3”
Three circuit
13.8”
5.9”
1.9”
PSD 288
13.06”
8.42”
4.47”
A
A
B
CB
C
C
0-10V Dimming Power Supplies:
Magnetic Low Voltage Dimming Power Supplies:
AB
48DCIRCUIT x POWER
CVECVE - CVE Series dims down to 0.1%
MODEL
48D - 48W48X2D - 2 x 48W48X3D - 3 x 48W48X4D - 4 x 48W96D - 96W96X2D - 2 x 96W96X3D - 3 x 96W96X4D - 4 x 96W
24OUTPUT
24 - 24 VDC
Electronic Low Voltage Dimming Power Supplies:
Blank - 120 V277 - 240/277 V
coverINPUT
CA
B
See fixture and power supply instructions & spec sheet for wiring information. Dimming possible in select models - view Luminii website for list of compatible dimmers.
MODELS 96W 3X96
A Length 14.40” (365.76mm) 15.75” (400.05mm)
B Width 5.20” (132.08mm) 6.60” (167.64mm)
C Depth 2.60” (66.04mm) 4.80” (121.92mm)
MODELS PSV Dry PSV Wet
A Length 9.2” (233.68mm) 9.5” (241.30mm)
B Width 3.4” (86.36mm) 4.12” (1104.64mm)
C Depth 1.9” (48.26mm) 2.3” (58.42mm)
REV0.0 09162019 page 3 of 6 www.luminii.com tel: 224-333-6033
LL91STP LineLED Linear LED strip - 24 VDC
24
24 LIN
48
3X96
Power supply
48 - 48 W96 - 96 W288 - 288 W (3x 96W)
96 - 96 WATT 3X96 - 3 X 96 WATT
24 - 24 VDC
24 - 24 VDC
Blank - 120 V240 - 240 V277 - 277 V
LIN - LinearLOG - Logarithmic
40POWER
POWER
POWER
PSV
PSD
PS010V
PSV - PSV Series dims down to 5%
PSD - PSD Series dims down to 0%
PS010V - 0-10V Power Supply dims down to 0%
MODEL
MODEL
MODEL
40 - 40 W60 - 60 W96 - 96 W
24OUTPUT
OUTPUT
OUTPUT
INPUT
DIMMING
24 - 24 VDC
U2DIM DDIMMING LOCATION
U2DIM - Dimming 0-10V D - Dry LocationIP65 - Wet Location
MODELS
A Length
B Width
C Depth
MODELS
A Length
B Width
C Depth
MODELS
A Length
B Width
C Depth
MODELS
A Length
B Width
C Depth
PSV Dry
9.2”
3.4”
1.9”
PSD 48
11.25”
3.42”
3.42”
PSV Wet
9.5”
4.12”
2.3”
PSD 96
11.25”
3.42”
3.27”
3X96
15.75”
6.60”
4.80”
Dual circuit
13.8”
4.0”
1.9”
Four circuit
13.8”
7.75”
1.9”
96 W
14.40”
5.20”
2.60”
Single circuit
13.9”
2.3”
1.3”
Three circuit
13.8”
5.9”
1.9”
PSD 288
13.06”
8.42”
4.47”
A
A
B
CB
C
C
0-10V Dimming Power Supplies:
Magnetic Low Voltage Dimming Power Supplies:
AB
48DCIRCUIT x POWER
CVECVE - CVE Series dims down to 0.1%
MODEL
48D - 48W48X2D - 2 x 48W48X3D - 3 x 48W48X4D - 4 x 48W96D - 96W96X2D - 2 x 96W96X3D - 3 x 96W96X4D - 4 x 96W
24OUTPUT
24 - 24 VDC
Electronic Low Voltage Dimming Power Supplies:
Blank - 120 V277 - 240/277 V
coverINPUT
CA
B
See fixture and power supply instructions & spec sheet for wiring information. Dimming possible in select models - view Luminii website for list of compatible dimmers.
MODELS PSD 48 PSD 96 PSD 288
A Length 11.25” (285.75mm) 11.25” (285.75mm) 13.06” (331.72mm)
B Width 3.42” (86.86mm) 3.42” (86.86mm) 8.42” (213.86mm)
C Depth 3.42” (86.86mm) 3.27” (83.05mm) 4.47” (113.53mm)
A
B C
A
C B
BA
C
Compatible Drivers
REV0.0 09162019 page 3 of 6 www.luminii.com tel: 224-333-6033
LL91STP LineLED Linear LED strip - 24 VDC
24
24 LIN
48
3X96
Power supply
48 - 48 W96 - 96 W288 - 288 W (3x 96W)
96 - 96 WATT 3X96 - 3 X 96 WATT
24 - 24 VDC
24 - 24 VDC
Blank - 120 V240 - 240 V277 - 277 V
LIN - LinearLOG - Logarithmic
40POWER
POWER
POWER
PSV
PSD
PS010V
PSV - PSV Series dims down to 5%
PSD - PSD Series dims down to 0%
PS010V - 0-10V Power Supply dims down to 0%
MODEL
MODEL
MODEL
40 - 40 W60 - 60 W96 - 96 W
24OUTPUT
OUTPUT
OUTPUT
INPUT
DIMMING
24 - 24 VDC
U2DIM DDIMMING LOCATION
U2DIM - Dimming 0-10V D - Dry LocationIP65 - Wet Location
MODELS
A Length
B Width
C Depth
MODELS
A Length
B Width
C Depth
MODELS
A Length
B Width
C Depth
MODELS
A Length
B Width
C Depth
PSV Dry
9.2”
3.4”
1.9”
PSD 48
11.25”
3.42”
3.42”
PSV Wet
9.5”
4.12”
2.3”
PSD 96
11.25”
3.42”
3.27”
3X96
15.75”
6.60”
4.80”
Dual circuit
13.8”
4.0”
1.9”
Four circuit
13.8”
7.75”
1.9”
96 W
14.40”
5.20”
2.60”
Single circuit
13.9”
2.3”
1.3”
Three circuit
13.8”
5.9”
1.9”
PSD 288
13.06”
8.42”
4.47”
A
A
B
CB
C
C
0-10V Dimming Power Supplies:
Magnetic Low Voltage Dimming Power Supplies:
AB
48DCIRCUIT x POWER
CVECVE - CVE Series dims down to 0.1%
MODEL
48D - 48W48X2D - 2 x 48W48X3D - 3 x 48W48X4D - 4 x 48W96D - 96W96X2D - 2 x 96W96X3D - 3 x 96W96X4D - 4 x 96W
24OUTPUT
24 - 24 VDC
Electronic Low Voltage Dimming Power Supplies:
Blank - 120 V277 - 240/277 V
coverINPUT
CA
B
See fixture and power supply instructions & spec sheet for wiring information. Dimming possible in select models - view Luminii website for list of compatible dimmers.
PURE DC® LITE (PDCL)
NOTE: Must be loaded at least 10% of rated load to obtain optimal dimming.
L Black N White
100 - 277 VAC
GROUND
24V DC+
24V DC-
Red+ Black-Ground
PURE DC® LITE
+
–
L Black N White
100 - 277 VAC
GROUND
24V DC+
24V DC-
Red+ Black-Ground
PURE DC® LITE
+
–
TRIAC DIMMER
PART DESCRIPTION
PDCL.30.24 30W 100-277VAC DIMMABLE DRIVER
PDCL.60.24 60W 100-277VAC DIMMABLE DRIVER
PDCL.96.24 96W 100-277VAC DIMMABLE DRIVER
DIMENSIONS
PDCL.30.24 H 1.03”(26.16mm); W 6.50”(165.10mm); D 3.62”(91.94mm)
PDCL.60.24 H 1.03”(26.16mm); W 7.40”(187.96mm); D 3.62”(91.94mm)
PDCL.96.24 H 1.61”(40.89mm); W 8.66”(219.96mm); D 3.66”(92.96mm)
DIMMING PERFORMANCE
PDCL.30.24 Dims to 1% on most MLV dimmers
See fixture and power supply instructions & spec sheet for wiring information. Dimming possible in select models - view Luminii website for list of compatible dimmers.
www.OpticArts.com tel: 213.250.6069
LineLED X18WET-T Wet Location Linear LED strip - 24 VDC
page 6 of 7REV1.0 November 14, 2019 12:54 PMREV0.0 09162019 page 4 of 6 www.luminii.com tel: 224-333-6033
LL91STP LineLED Linear LED strip - 24 VDC
24
24
96
96
96 - 96 WATT 3X96 - 3 X 96 WATT
96 - 96 WATT 3X96 - 3 X 96 WATT
24 - 24 VDC
24 - 24 VDC
POWER
POWER
PSDMX
PSDALI
PSDMX - DMX Power Supply
PSDALI - DALI Power Supply dims down to 0%
MODEL
MODEL
OUTPUT
OUTPUT
MODELS
A Length
B Width
C Depth
MODELS
A Length
B Width
C Depth
3X96 W
15.75”
6.60”
4.80”
96 W
14.40”
5.20”
2.60”
A
BCDMX Dimming Power Supplies:
DALI Dimming Power Supplies:
MODEL MODEL MODEL
LTEA4U1UKL-CV240 L3DA4U1UKL-CV240Lutron – Hi-lume™ 1% 2-wire LED driver (120V forward phase only)
Hi-lume™ 1% EcoSystem Voltage LED Driver
L3D0-96W24V-U Hi-lume™ 0.1% EcoSystem Voltage LED Driver with Soft-On, Fade-to-Black™
MODELS
A Length
B Width
C Depth
MODELS
A Length
B Width
C Depth
LTEA
4.89”
2.66”
4.00”
L3DO
10.50”
5.50”
2.00”
L3DA
4.89”
2.66”
4.00”
A
A
B C
B
C
Luminii is a Lutron OEM Advantage Partner
- Features eldoLED’s LINEARdrive configurable dimmable drivers
- Features eldoLED’s LINEARdrive configurable dimmable drivers
Power supplySee fixture and power supply instructions & spec sheet for wiring information. Dimming possible in select models - view Luminii website for list of compatible dimmers.
AB
C
REV0.0 09162019 page 4 of 6 www.luminii.com tel: 224-333-6033
LL91STP LineLED Linear LED strip - 24 VDC
24
24
96
96
96 - 96 WATT 3X96 - 3 X 96 WATT
96 - 96 WATT 3X96 - 3 X 96 WATT
24 - 24 VDC
24 - 24 VDC
POWER
POWER
PSDMX
PSDALI
PSDMX - DMX Power Supply
PSDALI - DALI Power Supply dims down to 0%
MODEL
MODEL
OUTPUT
OUTPUT
MODELS
A Length
B Width
C Depth
MODELS
A Length
B Width
C Depth
3X96 W
15.75”
6.60”
4.80”
96 W
14.40”
5.20”
2.60”
A
BCDMX Dimming Power Supplies:
DALI Dimming Power Supplies:
MODEL MODEL MODEL
LTEA4U1UKL-CV240 L3DA4U1UKL-CV240Lutron – Hi-lume™ 1% 2-wire LED driver (120V forward phase only)
Hi-lume™ 1% EcoSystem Voltage LED Driver
L3D0-96W24V-U Hi-lume™ 0.1% EcoSystem Voltage LED Driver with Soft-On, Fade-to-Black™
MODELS
A Length
B Width
C Depth
MODELS
A Length
B Width
C Depth
LTEA
4.89”
2.66”
4.00”
L3DO
10.50”
5.50”
2.00”
L3DA
4.89”
2.66”
4.00”
A
A
B C
B
C
Luminii is a Lutron OEM Advantage Partner
- Features eldoLED’s LINEARdrive configurable dimmable drivers
- Features eldoLED’s LINEARdrive configurable dimmable drivers
Power supplySee fixture and power supply instructions & spec sheet for wiring information. Dimming possible in select models - view Luminii website for list of compatible dimmers.
AB
C
MODELS 3X96 W
A Length 15.75” (400.05mm)
B Width 6.60” (167.64mm)
C Depth 4.80” (121.92mm)
MODELS 3X96 W
A Length 14.40” (365.76mm)
B Width 5.20” (132.08mm)
C Depth 2.60” (66.04mm)
MODELS L3DO
A Length 10.50” (266.70mm)
B Width 5.50” (139.70mm)
C Depth 2.00” (50.80mm)
B
A
C
A
C
B
A
C
BMODELS LTEA L3DA
A Length 4.89” (124.20mm) 4.89” (124.20mm)
B Width 2.66” (67.56mm) 2.66” (67.56mm)
C Depth 4.00” (101.60mm) 4.00” (101.60mm)
A
CB
www.OpticArts.com tel: 213.250.6069
LineLED X18WET-T Wet Location Linear LED strip - 24 VDC
page 7 of 7REV1.0 November 14, 2019 12:54 PM
REV0.0 09162019 page 5 of 6 www.luminii.com tel: 224-333-6033
LL91STP LineLED Linear LED strip - 24 VDC
Power supplySee fixture and power supply instructions & spec sheet for wiring information. Dimming possible in select models - view Luminii website for list of compatible dimmers.
24 ENL D9696 - 96 WATT 24 - 24 VDC ENL - Enlighted
DimmingD - Damp
POWER
PSVPSV- LED Power Supply
MODEL OUTPUT DIMMING Location
Enlighted Enabled Dimming Power Supplies:
40POWER
PSVPSV - PSV Series
MODEL
40 - 40 W60 - 60 W96 - 96 W
24OUTPUT
24 - 24 VDC
U2ND DDIMMING LOCATION
U2ND - Non Dimming D - Dry LocationIP65 - Wet Location
MODELS
A Length
B Width
C Depth
PSV Dry
9.2”
3.4”
1.9”
PSV Wet
9.5”
4.12”
2.3”
C
Non-Dimming Power Supplies:
AB
MODELS
A Length
B Width
C Depth
96 W
14.40”
5.20”
2.60”
AB
C
C
A B
MODELS
A Length
B Width
C Depth
Dual circuit
8.0”
8.0”
8.0”
96X2CIRCUIT x POWER
IG-CVEIG-CVE - In ground CVE Series dims down to 0.1%
MODEL
96X2 - 2 x 96W
24OUTPUT
24 - 24 VDC
In ground, Electronic Low Voltage Dimming Power Supplies:
Blank - 120 V277 - 240/277 V
INPUT
REV0.0 09162019 page 5 of 6 www.luminii.com tel: 224-333-6033
LL91STP LineLED Linear LED strip - 24 VDC
Power supplySee fixture and power supply instructions & spec sheet for wiring information. Dimming possible in select models - view Luminii website for list of compatible dimmers.
24 ENL D9696 - 96 WATT 24 - 24 VDC ENL - Enlighted
DimmingD - Damp
POWER
PSVPSV- LED Power Supply
MODEL OUTPUT DIMMING Location
Enlighted Enabled Dimming Power Supplies:
40POWER
PSVPSV - PSV Series
MODEL
40 - 40 W60 - 60 W96 - 96 W
24OUTPUT
24 - 24 VDC
U2ND DDIMMING LOCATION
U2ND - Non Dimming D - Dry LocationIP65 - Wet Location
MODELS
A Length
B Width
C Depth
PSV Dry
9.2”
3.4”
1.9”
PSV Wet
9.5”
4.12”
2.3”
C
Non-Dimming Power Supplies:
AB
MODELS
A Length
B Width
C Depth
96 W
14.40”
5.20”
2.60”
AB
C
C
A B
MODELS
A Length
B Width
C Depth
Dual circuit
8.0”
8.0”
8.0”
96X2CIRCUIT x POWER
IG-CVEIG-CVE - In ground CVE Series dims down to 0.1%
MODEL
96X2 - 2 x 96W
24OUTPUT
24 - 24 VDC
In ground, Electronic Low Voltage Dimming Power Supplies:
Blank - 120 V277 - 240/277 V
INPUT
REV0.0 09162019 page 5 of 6 www.luminii.com tel: 224-333-6033
LL91STP LineLED Linear LED strip - 24 VDC
Power supplySee fixture and power supply instructions & spec sheet for wiring information. Dimming possible in select models - view Luminii website for list of compatible dimmers.
24 ENL D9696 - 96 WATT 24 - 24 VDC ENL - Enlighted
DimmingD - Damp
POWER
PSVPSV- LED Power Supply
MODEL OUTPUT DIMMING Location
Enlighted Enabled Dimming Power Supplies:
40POWER
PSVPSV - PSV Series
MODEL
40 - 40 W60 - 60 W96 - 96 W
24OUTPUT
24 - 24 VDC
U2ND DDIMMING LOCATION
U2ND - Non Dimming D - Dry LocationIP65 - Wet Location
MODELS
A Length
B Width
C Depth
PSV Dry
9.2”
3.4”
1.9”
PSV Wet
9.5”
4.12”
2.3”
C
Non-Dimming Power Supplies:
AB
MODELS
A Length
B Width
C Depth
96 W
14.40”
5.20”
2.60”
AB
C
C
A B
MODELS
A Length
B Width
C Depth
Dual circuit
8.0”
8.0”
8.0”
96X2CIRCUIT x POWER
IG-CVEIG-CVE - In ground CVE Series dims down to 0.1%
MODEL
96X2 - 2 x 96W
24OUTPUT
24 - 24 VDC
In ground, Electronic Low Voltage Dimming Power Supplies:
Blank - 120 V277 - 240/277 V
INPUT
MODELS 96 W
A Length 14.40” (365.76mm)
B Width 5.20” (132.08mm)
C Depth 2.60” (66.04mm)
MODELS 96 W
A Length 8.00” (203.20mm)
B Width 8.00” (203.20mm)
C Depth 8.00” (203.20mm)
MODELS PSV Dry PSV Wet
A Length 9.20” (233.68mm) 9.50” (241.30mm)
B Width 3.40” (86.36mm) 4.12” (104.90mm)
C Depth 1.90” (48.26mm) 2.30” (58.42mm)
A
C
B
A
B
C
A B
C